Notice

Note that when converting this document from its original format to a
.pdf file, some minor font and format changes may occur. When
viewing and printing this document, we cannot guarantee that your
specific PC or printer will support all of the fonts or graphics.
Therefore, when you view the document, fonts may be substituted and
your individual printer may not have the capability to print the
document correctly.
Hardware Manual

A50-031693-003 NA
ISSUE 1.0
September 2011
Copyright
NEC Corporation reserves the right to change the specifications, functions, or features at any time
without notice.

NEC Corporation has prepared this document for use by its employees and customers. The informa-
tion contained herein is the property of NEC Corporation and shall not be reproduced without prior
written approval of NEC Corporation.

Copyright 2011

NEC Corporation

Printed in Japan
 TABLE OF CONTENTS

Regulatory
Chapter 1 Introduction
Section 1 GENERAL INFORMATION .................................................... 1-1
Section 2 EQUIPMENT LIST ................................................................ 1-2
2.1 KSUs and Optional Unit .................................................................. 1-3
2.1.1 IP4[ ]-1228M-B KSU ................................................................. 1-3
2.1.2 IP4[ ]-1228ME-B EXP ............................................................... 1-3
2.1.3 IP4WW-EXIFB-C1 ................................................................... 1-4
2.1.4 IP4WW-Battery Box ................................................................. 1-4
2.2 Trunk/Extension/ISDN Expansion Interface Cards ................................ 1-5
2.2.1 IP4WW-080E-B1 ..................................................................... 1-5
2.2.2 IP4WW-008E-B1 ..................................................................... 1-5
2.2.3 IP4WW-4COIDB-B1 ................................................................. 1-5
2.2.4 IP4WW-1PRIU-C1 ................................................................... 1-5
2.3 Optional Interface Cards ................................................................. 1-6
2.3.1 IP4WW-VOIPDB-C1 ................................................................. 1-6
2.3.2 IP4WW-CFVMS-C1/IP4WW-CFVML-C1 ......................................... 1-6
2.4 Multiline Telephones and Optional Equipment ......................................1-6
2.4.1 IP4WW-12TXH-B TEL ............................................................... 1-6
2.4.2 IP4WW-24TXH-B TEL ............................................................... 1-6
2.4.3 IP4[ ]-24TIXH-C TEL ................................................................. 1-7
2.4.4 IP4WW-60D DSS-B ................................................................. 1-7
2.4.5 DP-D-1D ............................................................................... 1-7
2.5 Wireless DECT Telephones ............................................................. 1-8
2.5.1 DTL-8R-1 Cordless DECT Telephone ............................................. 1-8
2.5.2 DTL-RPT-1 Cordless DECT Telephone Repeater ............................... 1-8
2.5.3 ML440 and AP20 Wireless DECT Telephone .................................... 1-8
Section 3 SYSTEM CAPACITY ............................................................. 1-9
3.1 System Capacity ........................................................................... 1-9
3.2 KSU Capacity ............................................................................. 1-10
3.2.1 Expandability of Trunk and Extension (without PRI) ...........................1-11
3.2.2 Expandability of Trunk and Extension (with PRI) ...............................1-12

Chapter 2 Installation
Section 1 INSTALLING THE MAIN & EXPANSION KSUs ....................... 2-1
1.1 Before Installing the KSU(s) ............................................................. 2-1
1.1.1 General Precautions ................................................................. 2-1
1.1.2 Preparations .......................................................................... 2-1
1.1.3 Site Requirements ................................................................... 2-1
1.1.4 Environmental Requirements ...................................................... 2-1
1.1.5 Unpacking ............................................................................. 2-2
1.2 Installing the Main KSU (1228M-B KSU) ............................................2-2
1.3 Wall-Mounting the KSU(s) ............................................................... 2-3
1.3.1 KSU Dimensions ..................................................................... 2-3
1.3.2 Wall Installation of KSU ............................................................. 2-4
1.3.3 Mounting Procedure of KSU ........................................................ 2-5
1.4 Installing the Expansion KSU(s) ....................................................... 2-7

Hardware Manual i
 TABLE OF CONTENTS
1.4.1 General ................................................................................ 2-7
1.4.2 Unpacking (EXIFB-C1) .............................................................. 2-7
1.4.3 Connectors Location (EXIFB-C1) .................................................. 2-8
1.4.4 Installing the EXIFB-C1 PCB ....................................................... 2-8
1.4.5 KSUs Inter-connection .............................................................2-10
1.5 Grounding and AC Cabling ............................................................ 2-12
1.5.1 Grounding the KSU .................................................................2-12
1.5.2 AC Power Requirement ............................................................2-12
1.5.3 AC Power Cord ......................................................................2-13
1.6 Trunk/Extension Cabling ............................................................... 2-13
1.6.1 General ...............................................................................2-13
1.6.2 Precautions for Cabling ............................................................2-13
1.6.3 Trunk Cabling ........................................................................2-14
1.6.4 Extension Cabling ...................................................................2-14
1.6.5 Cable Routing and Clamping ......................................................2-16
Section 2 INSTALLING THE EXTERNAL BACKUP BATTERY .............. 2-17
2.1 General ......................................................................................2-17
2.2 Unpacking ..................................................................................2-17
2.3 Battery Box Dimensions ................................................................ 2-18
2.4 Battery Specifications ................................................................... 2-18
2.5 Battery Installation ....................................................................... 2-18
2.6 Mounting the IP4WW-Battery Box ................................................... 2-24
2.6.1 Floor-Mounting the IP4WW-Battery Box .........................................2-24
2.6.2 Wall-Mounting the IP4WW-Battery Box ..........................................2-26
2.6.3 Mounting One KSU on the Battery Box ..........................................2-30
2.7 IP4WW-Battery Box to KSU Connection ........................................... 2-33
2.8 IP4WW-Battery Box Fuse Replacement ........................................... 2-34
Section 3 INSTALLING THE EXPANSION INTERFACE CARDS ........... 2-38
3.1 General ......................................................................................2-38
3.2 Unpacking ..................................................................................2-38
3.3 Mounting the Expansion Interface Card ............................................ 2-39
3.3.1 Mounting the 080E-B1/008E-B1/1PRIU-C1 PCBs .............................2-39
3.3.2 Mounting the 4COIDB PCB ........................................................2-43
3.4 Cabling and Setting the Expansion Interface Card .............................. 2-44
3.4.1 Cabling IP4WW-080E-B1 ..........................................................2-45
3.4.2 Cabling IP4WW-008E-B1 ..........................................................2-46
3.4.3 Cabling and Setting IP4WW-4COIDB-B1 .......................................2-48
3.4.4 Cabling and Setting IP4WW-1PRIU-C1 .........................................2-49
3.5 Power Failure Transfer (4COIDB-B1 only) ........................................ 2-51
3.5.1 General ...............................................................................2-51
Section 4 INSTALLING THE OPTIONAL INTERFACE CARDS ............. 2-52
4.1 VoIP Card (VOIPDB-C1) ............................................................... 2-52
4.1.1 General ...............................................................................2-52
4.1.2 Unpacking ............................................................................2-52
4.1.3 Installing the VOIPDB-C1 PCB ...................................................2-52
4.1.4 LED Indication .......................................................................2-55
4.2 Installing the CF Card (CFVMS/CFVML) .......................................... 2-56
Section 5 INSTALLING THE MULTILINE TELEPHONES AND OPTIONAL
TERMINALS ....................................................................... 2-57

ii Hardware Manual
 TABLE OF CONTENTS
5.1 Installing the Multiline Telephones ................................................... 2-57
5.1.1 Location of Controls ................................................................2-57
5.1.2 Multiline Telephone Legs Adjustment ............................................2-58
5.1.3 Wall-Mounting the Multiline Telephone ...........................................2-60
5.2 Install the IP Multiline Telephone (IP4WW-24TIXH-C1 TEL) .................. 2-62
5.2.1 System Connection .................................................................2-62
5.2.2 Installing the IP Multiline Telephone ..............................................2-62
5.2.3 Applying Power to the IP Multiline Telephone ...................................2-62
5.3 Installing the DSS Console ............................................................ 2-63
5.3.1 DSS Console Leg Adjustment .....................................................2-63
5.3.2 Wall-Mounting the DSS Console .................................................2-64
5.4 Installing the Headset ................................................................... 2-65
5.5 Installing the Doorphone Box ......................................................... 2-66
5.5.1 Wall-Mounting the Doorphone ....................................................2-66
5.5.2 Connecting the Doorphone ........................................................2-68
5.5.3 Doorphone Interface Specifications ..............................................2-68
5.6 Installing the Door Unlock Devices .................................................. 2-69
5.7 Installing the External Paging Speaker/External MOH/BGM Sources ...... 2-70
5.7.1 Connecting the Audio Equipment .................................................2-70
5.7.2 External Paging Output Specifications ...........................................2-70
5.7.3 BGM/External MOH Source Input Specifications ..............................2-71
5.8 SMDR (Station Message Detail Recording) ....................................... 2-71
5.8.1 General ...............................................................................2-71
Section 6 INSTALLING WIRELESS DECT TELEPHONES .................... 2-72
6.1 Installing the DTL-8R-1 Cordless DECT Telephone ............................. 2-72
6.1.1 Selecting a Location ................................................................2-72
6.1.2 Installation Precautions ............................................................2-73
6.1.3 Connecting the Telephone Cords .................................................2-73
6.1.4 Applying Power to the Charging Unit .............................................2-74
6.1.5 Mounting the Base to a Standard Wall Plate ....................................2-74
6.1.6 Mounting the Base Directly to the Wall ..........................................2-76
6.1.7 Wall Mounting the Charging Unit .................................................2-78
6.1.9 Attaching and Removing the Belt Clip ...........................................2-80
6.1.9 Installing the Handset Battery Pack ..............................................2-80
6.1.10 Charging Batteries .................................................................2-81
6.1.11 Charging Spare Battery Packs ...................................................2-81
6.2 Installing the DTL-RPT-1 Cordless DECT Telephone REPEATER .......... 2-82
6.2.1 Setting Up Your Repeater ..........................................................2-84
6.2.2 Installing the Repeater .............................................................2-85
6.2.3 Troubleshooting Chart ..............................................................2-88
6.2.4 Turning on the Verification Tone ..................................................2-88
6.2.5 Maintenance .........................................................................2-88
6.3 Installing the ML440 and AP20 Wireless DECT Telephone ................... 2-88
6.3.1 Connecting the Base Station ......................................................2-89
6.3.2 Wall Mounting the Base Station ...................................................2-90
6.3.3 Handset and Charger ...............................................................2-92

Chapter 3 System Start Up

Section 1 SYSTEM START UP ............................................................. 3-1
1.1 Before Starting Up the System ......................................................... 3-1
1.2 Starting Up the System ................................................................... 3-1

Hardware Manual iii

 TABLE OF CONTENTS
1.2.1 Perform a Cold Start ................................................................. 3-2
1.2.2 Perform a Hot Start .................................................................. 3-3
Section 2 PROGRAMMING MODE ....................................................... 3-4
2.1 Entering the Programming Mode ...................................................... 3-4
2.2 Exiting the Programming Mode ........................................................ 3-4
2.3 Saving (Backup) the Customer Data .................................................. 3-4
2.4 Loading the Customer Data ............................................................. 3-5
Section 3 SYSTEM SHUT DOWN ......................................................... 3-7
3.1 Powering Off the System ................................................................ 3-7
3.2 Resetting the System ..................................................................... 3-7

Chapter 4 Maintenance
Section 1 FUSE REPLACEMENT ......................................................... 4-1
1.1 Replacing the Fuse ........................................................................ 4-1
Section 2 LITHIUM BATTERY REPLACEMENT ..................................... 4-4
2.1 General ....................................................................................... 4-4
2.2 Lithium Battery Specification ............................................................ 4-4
2.3 Replacing the Lithium Battery .......................................................... 4-4
Section 3 MAIN SOFTWARE UPGRADING ........................................... 4-8
3.1 General ....................................................................................... 4-8
3.2 Before Upgrading the Main Software ................................................. 4-8
3.3 Main Software Version Confirmation .................................................. 4-8
3.4 Upgrading the Main Software ........................................................... 4-9
Section 4 LED INDICATIONS ............................................................. 4-12

Chapter 5 Specifications
Section 1 SYSTEM CAPACITY ............................................................. 5-1
Section 2 SYSTEM SPECIFICATIONS .................................................. 5-3
2.1 General Precautions ...................................................................... 5-3
2.2 Environmental Requirements ........................................................... 5-3
2.3 Operating Conditions ..................................................................... 5-3
2.4 Site Requirements ......................................................................... 5-3
2.5 AC Power Requirement .................................................................. 5-3
2.6 Electrical Specifications <Power Supply> (KSU) .................................. 5-4
2.7 IP Terminal Power Chart ................................................................. 5-4
2.8 IEEE802.af Class Specification ........................................................ 5-4
2.9 Mechanical Specifications ............................................................... 5-5
2.10 Optional Unit Mechanical Specifications ........................................... 5-5
2.11 Doorphone Interface Specifications ................................................. 5-5
2.12 General Purpose/Door Unlock Relay Specifications ............................ 5-6
2.13 External Paging Output Specifications .............................................. 5-6
2.14 BGM/ExMOH Source Input Specifications ......................................... 5-6
2.15 External Sensor Device Interface Specifications ................................. 5-6
2.16 CPU Card LAN Port Specifications .................................................. 5-6
2.17 Cabling Requirements .................................................................. 5-7

iv Hardware Manual
 TABLE OF CONTENTS
2.18 Cable Requirements .................................................................... 5-7

Hardware Manual v
 LIST OF TABLES
Table 1-1 System Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Table 2-1 KSU Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Table 2-2 Items on the CPU card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Table 2-3 EXIFB-C1 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Table 2-4 Connectors of EXIFB-C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Table 2-5 Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Table 2-6 RJ61 Cable Connector Pin-Outs (J101-J103) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Table 2-7 IP4WW-Battery Box Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Table 2-8 Battery Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Table 2-9 Expansion Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Table 2-10 Expansion Card Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Table 2-11 RJ-61 Digital Connector Pin-Outs (J101, J102) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-46
Table 2-12 RJ-61 Analog Pin-Outs (J101, J102) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-47
Table 2-13 RJ-61 CO/PF Pin-Outs (J2, J3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Table 2-14 RJ-45 PRI Pin-Outs (S-Bus, T-Bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-49
Table 2-15 Switch Setting of 1PRIU-C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
Table 2-16 LED Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50
Table 2-17 T1 LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51
Table 2-18 VOIPDB-C1 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
Table 2-19 VOIPDB LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55
Table 2-20 Operation of VOIPDB LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
Table 2-21 Multiline Telephone Functions (12TXH/24TXH/24TIXH (IP)) . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-57
Table 2-22 Doorphone Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-68
Table 2-23 RJ-61 General Purpose/Door Unlock Relay Control Connector (J7) . . . . . . . . . . . . . . . . . . .2-69
Table 2-24 General Purpose/Door Unlock Relay Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69
Table 2-25 External Paging Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
Table 2-26 BGM/External MOH Source Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-71
Table 2-27 Base Station LEDs States and Meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-90
Table 3-1 Start Up Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Table 4-1 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Table 4-2 CPU LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Table 5-1 System Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Table 5-2 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Table 5-3 Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Table 5-4 Electrical Specifications of KSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-5 IP Terminal Power Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-6 IEEE802.af Class Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Table 5-7 Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Table 5-8 Optional Unit Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Table 5-9 Doorphone Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Table 5-10 General Purpose/Door Unlock Relay Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Table 5-11 External Paging Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Table 5-12 BGM/External MOH Source Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Table 5-13 External Sensor Device Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Table 5-14 CPU Card LAN Port Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Table 5-15 Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

vi Hardware Manual
 LIST OF FIGURES
Figure 1-1 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Figure 1-2 System Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI) . . . . . .1-11
Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI) . . . . . . . . . 1-12
Figure 2-1 CPU Card Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Figure 2-2 Dimension of the Main and Expansion KSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Figure 2-3 Vertical Arrangement of KSUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-4 Horizontal Arrangement of KSUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-5 Wall-Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-6 Screw Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-7 Sub-Cover Slide-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-8 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-9 Sub-Cover Open Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Figure 2-10 Mounting the KSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Figure 2-11 Connectors of EXIFB-C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-12 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-13 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-14 EXIFB-C1 PCB Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-15 Removing the Plastic Knockouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-16 Replacing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Figure 2-17 Connection of KSUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Figure 2-18 Installing Ferrite Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Figure 2-19 ETH Lug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Figure 2-20 AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Figure 2-21 Digital Extension Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Figure 2-22 Analog Extension Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Figure 2-23 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Figure 2-24 Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Figure 2-25 Dimension of the IP4WW-Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Figure 2-26 Removing the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Figure 2-27 Disconnect Battery Connection Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Figure 2-28 Batt Stopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Figure 2-29 Pulling out the Battery Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20
Figure 2-30 Remove the Battery Tray Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21
Figure 2-31 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Figure 2-32 Connecting the Battery Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Figure 2-33 Installation of Battery Tray Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Figure 2-34 Inserting the Battery Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Figure 2-35 Secure Batt Stopper Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Figure 2-36 Connecting the Battery Connection Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Figure 2-37 Installation of Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Figure 2-38 Bases and Support of the Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-25
Figure 2-39 Floor-Mount Spacing Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Figure 2-40 Mounting the Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Figure 2-41 Securing the Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Figure 2-42 Assemble Battery Box Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Figure 2-43 Wall-Mount Spacing Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Figure 2-44 Removing the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Figure 2-45 Mounting the Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Figure 2-46 Securing the Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Figure 2-47 Removing the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Figure 2-48 Removing the L-Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Figure 2-49 Securing the L-Bracket and WM Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-32

Hardware Manual vii

 LIST OF FIGURES
Figure 2-50 Attaching the KSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Figure 2-51 KSU Mounting on Battery Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Figure 2-52 Sub-Cover Open and Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Figure 2-53 Connecting Battery Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Figure 2-54 Removing the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Figure 2-55 Disconnecting the Battery Connection Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Figure 2-56 Loosen the Fuse Unit Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Figure 2-57 Replacing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Figure 2-58 Install the Fuse Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Figure 2-59 Securing the Fuse Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Figure 2-60 Connect Battery Connection Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Figure 2-61 Installation of the Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Figure 2-62 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Figure 2-63 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Figure 2-64 Mounting the 1st Expansion Interface Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-40
Figure 2-65 Mounting the 2nd Expansion Interface Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-41
Figure 2-66 Mounting Two Expansion Interface Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
Figure 2-67 Plastic Knockouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Figure 2-68 Replacing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Figure 2-69 Plastic Knockouts on 084M-B1/080E-B1/008E-B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Figure 2-70 Installing the 4COIDB-B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Figure 2-71 Mounting the 4COIDB-B1 into the KSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-44
Figure 2-72 Replacing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44
Figure 2-73 Connectors of 080E-B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45
Figure 2-74 Connectors of 008E-B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
Figure 2-75 Connectors of 4COIDB-B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Figure 2-76 Connector of 1PRIU-C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-49
Figure 2-77 Switches and LEDs Location of 1PRIU-C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50
Figure 2-78 1PRIU-C1 LED Indication Pattern of Layer 1 on T1 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-51
Figure 2-79 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
Figure 2-80 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-53
Figure 2-81 Removing the CPU Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-53
Figure 2-82 Installing the VOIPDB-C1 PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-53
Figure 2-83 Installing the CPU Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54
Figure 2-84 Removing the Plastic Knockout and Replacing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . .2-54
Figure 2-85 Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55
Figure 2-86 Location of LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55
Figure 2-87 Installing the CF Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
Figure 2-88 Multiline Telephone (12TXH/24TXH/24TIXH (IP)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57
Figure 2-89 Leg Setting for Low Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58
Figure 2-90 Cabling of Multiline Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58
Figure 2-91 Setting for High Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
Figure 2-92 Leg Setting for High Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
Figure 2-93 Cabling for Wall-Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60
Figure 2-94 Wall-Mount Unit - 24TIXH-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60
Figure 2-95 Hook-Switch Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61
Figure 2-96 Wall-Mount Screw Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61
Figure 2-97 Mounting the Multiline Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61
Figure 2-98 IP Multiline Telephone Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62
Figure 2-99 IP Multiline Telephone Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62
Figure 2-100 Low Position Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63
Figure 2-101 Cabling of DSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63
Figure 2-102 Leg Stopper of DSS Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64
Figure 2-103 High Position Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64
Figure 2-104 Cabling for Wall-Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65

viii Hardware Manual

 LIST OF FIGURES
Figure 2-105 Wall-Mount Screw Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65
Figure 2-106 Mounting the DSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-65
Figure 2-107 Headset Socket (2-wire Multiline Telephone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
Figure 2-108 Headset Socket (IP Multiline Telephone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
Figure 2-109 Doorphone Box and Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67
Figure 2-110 Doorphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67
Figure 2-111 Connecting the Doorphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-68
Figure 2-112 Connecting the Door Unlock Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69
Figure 2-113 Connecting Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
Figure 2-114 Connecting a PC for SMDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-71
Figure 2-115 Cordless DECT Telephone (DTL-8R-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-72
Figure 2-116 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-72
Figure 2-117 Connecting Telephone Cords to the Telephone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73
Figure 2-118 Connecting the DTL-8R-1 Cordless DECT to the Multiline Terminal . . . . . . . . . . . . . . . . 2-73
Figure 2-119 Applying Power to the Charging Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-74
Figure 2-120 Polarized Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-74
Figure 2-121 Attaching the Wall Mount Stand to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-75
Figure 2-122 Placing the AC Adapter Cord Inside the Wall Mount Stand . . . . . . . . . . . . . . . . . . . . . . . . . . 2-75
Figure 2-123 Placing the Base Unit on the Posts of the Wall Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-76
Figure 2-124 Plugging the AC Adapter into the AC Wall Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-76
Figure 2-125 Inserting Screws into the Wall for Wall Mounting the Telephone . . . . . . . . . . . . . . . . . . . . 2-77
Figure 2-126 Placing the Telephone Cords Inside the Wall Mount Stand . . . . . . . . . . . . . . . . . . . . . . . . . . 2-77
Figure 2-127 Attaching the Wall Mount Unit to the Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-77
Figure 2-128 Inserting Screws for Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78
Figure 2-129 Wrapping the AC Adapter Cord Around the Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78
Figure 2-130 Placing the Charging Unit on the Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-79
Figure 2-131 Attaching the Belt Clip to the Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-79
Figure 2-132 Removing the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80
Figure 2-133 Removing the Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80
Figure 2-134 Replacing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80
Figure 2-135 Replacing the Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-81
Figure 2-136 Cordless DECT Telephone Repeater DTL-RPT-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-82
Figure 2-137 Single Repeater Attached to Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83
Figure 2-138 Six Repeaters Attached to Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83
Figure 2-139 Daisy-Chain Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-84
Figure 1-174 Base Coverage Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-113
Figure 2-141 Incorrect Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87
Figure 2-142 Base Coverage Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87
Figure 2-143 Daisy-Chain Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88
Figure 2-144 Base Station Front and Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-89
Figure 2-145 Connecting the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-90
Figure 2-146 Base Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-91
Figure 2-147 Handset Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-92
Figure 2-148 Charger Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93
Figure 2-149 Installing the Handset Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-93
Figure 2-150 Inserting Handset into the Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-94
Figure 3-1 Lithium Battery Protection Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Figure 3-2 Power Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Figure 3-3 Load Button (S1) Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Figure 3-4 Status LED (D5) and RUN LED Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Figure 3-5 Display Indication (Idle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Figure 3-6 Entering Programming Mode Display 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-7 Entering Programming Mode Display 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-8 Exiting the Programming Mode Display 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-9 Exiting Programming Mode Display 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Hardware Manual ix
 LIST OF FIGURES
Figure 3-10 Inserting the CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Figure 3-11 PRG90-03 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Figure 3-12 PRG90-04 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Figure 3-13 Inserting the CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-14 PRG90-04 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-15 Next PRG Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-16 Power Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Figure 4-1 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Figure 4-2 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-3 Exchanging the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-4 Replacing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-5 Warning of Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-6 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-7 Disconnecting the AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-8 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-9 Removing the CPU Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-10 Location of Lithium Battery Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-11 Removing the Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-12 Inserting the Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Figure 4-13 Installing the CPU Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Figure 4-14 Display of Multiline Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Figure 4-15 Removing the Sub-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Figure 4-16 Removing the Main-Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Figure 4-17 Inserting the CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-18 LOAD Button (S1) Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-19 Removing the CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

x Hardware Manual
ISSUE 1.0 SL1100

Regulatory
GENERAL INFORMATION
This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.
On the equipment is a label that contains, among other information, a product identifier in the format:
US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The telephone company may make changes in its technical operations and procedures. When such
changes affect the compatibility or use of the SL1100 system, the telephone company is required to
give adequate notice of the changes in order for you to maintain uninterrupted service.

The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the local
telephone company. For products approved after July 23, 2001, the REN for this product is the
product identifier in format: US:AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3).

Connection to party line service is subject to state tariffs. Contact the state public utilities commission,
public service commission or corporation commission for information.

For single and two-line equipment that connects to the telephone network via a plug and jack, the plug
and jack used with this equipment must comply with FCC Part 68 rules.

A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It must be connected to a compatible
modular jack that is also compliant.

TELEPHONE/SERVICE PROVIDER COMPANY NOTIFICATION

Before connecting this telephone system to the telephone network, the following information must be
provided to the telephone company:
1. Your telephone number.
2. FCC registration number:
• When the system is to be installed as a Key Function system (no dial access to Trunk Groups/Route
Advance Blocks), use the following number:
US:NIFKF10BSL1100
• When the system is to be installed as a Multifunction system, use the following number:
US:NIFMF10BSL1100
• When the system is to be installed as a PBX system, use the following number:
US:NIFPF10BSL1100

Ringer Equivalence Number (REN): 1.0B

USOC jacks required: RJ11C, RJEX, RJ2FX, RJ2HX, RJ48C, RJ21X

INCIDENCE OF HARM
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not prac-
tical, the telephone company will notify the customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide
advance notice in order for you to make necessary modifications to maintain interrupted service.

Hardware Manual R-1

SL1100 ISSUE 1.0

REPAIR SERVICE REQUIREMENTS

If the equipment is causing harm to the telephone network, the telephone company may request that
you disconnect the equipment until the problem is resolved.

If equipment malfunctions, all repairs must be performed by an authorized agent of NEC Corporation
of America or by NEC Corporation of America. The user requiring service is responsible for reporting
the need for service to a NEC Corporation of America authorized agent or to NEC Corporation of
America.

PRIVATE (LEASED) LINES

For Private (Leased) Line (Analog Data Format) equipment, type JM8 jack is required. Refer to ATIS
Technical Report No. 5 for details on this connector.
The Facility Interface Code (FIC) associated with each private line application represents the type of
service that will be provided by the telephone company. The user instructions must contain a detailed
list of private line ports and the associated FICs for which the equipment has been approved. In
addition, the Service Order Code (SOC) must also be included for analog systems. The SOC indicates
the degree of network protection provided by the equipment,.
For Private (Leased) Line (Digital Format) equipment, in addition to the general requirements for all
equipment, certain digital connections require that an encoded analog content and billing protection
affidavit be provided the telephone company. Customer instructions must contain information on the
preparation and submission of the affidavit.
To comply with state tariffs, the telephone company must be given notification prior to connection. In
some states, the state public utility commission, public service commission or corporation commission
must give prior approval of connection.

TOLL RESTRICTION AND LEAST COST ROUTING EQUIPMENT

The consumer/purchaser/supplier instructions accompanying this equipment and/or software features
must contain the following notice:
• The software contained in the SL1100 to allow user access to the network must be upgraded to
recognize newly established network area codes and exchange codes as they are placed into
service.
• Failure to upgrade the premises systems or peripheral equipment to recognize the new codes as
they are established will restrict the customer and the customer's employees from gaining access to
the network and these codes.

DIRECT INWARD DIALING

ALLOWING THIS EQUIPMENT TO BE OPERATED IN SUCH A MANNER AS TO NOT PROVIDE
FOR PROPER ANSWER SUPERVISION IS A VIOLATION OF PART 68 OF THE FCC RULES.

Direct Inward Dialing (DID) must contain the following:

Proper Answer Supervision is when:

• This equipment returns answer supervision to the Public Switched Telephone Network (PSTN) when
Direct Inward Dialing (DID) calls are:
• Answered by the called station.
• Answered by the Attendant.
• Routed to a recorded announcement that can be administered by the Customer Premise Equipment
(CPE) user.
• Routed to a dial prompt.
• This equipment returns answer supervision on all DID calls forwarded to the Public Switched Tele-
phone Network (PSTN). Permissible exceptions are:
• A call is unanswered.
• A busy tone is received.

R-2 Regulatory
ISSUE 1.0 SL1100

• A reorder tone is received.

VOICE ANNOUNCEMENT/MONITORING OVER DID LINES

When using voice announcement or monitoring over DID Lines, observe the following.

CAUTION

Using the Voice Announcement feature to eavesdrop or record sound activities at the other end of the
telephone line may be illegal under certain circumstances and laws. Consult a legal advisor before
implementing any practice to monitor or record a telephone conversation. Some federal and state laws
require a party monitoring or recording a telephone to use a beep-tone(s), notify all parties to the tele-
phone conversation and/or obtain consent of all parties to the telephone conversation. In monitoring or
recording sound activities at the other end of the telephone line using the Voice Announcement
feature, the sound of the alert tone at the beginning of the Voice Announcement may or may not be
considered sufficient under applicable laws. Some of the applicable laws provide for strict penalties for
illegal monitoring or recording of telephone conversations.

EQUAL ACCESS REQUIREMENTS

If equipment such as Private Branch Exchanges (PBX), key systems or customer-owned coin/credit
card telephones is sold to a call aggregator, it must be capable of providing users access to interstate
providers of operator services through the use of access codes. Modification of this equipment by call
aggregators to block access dialing codes is a violation of the Telephone Operator Consumers Act of
1990.

ELECTRICAL SAFETY ADVISORY

Parties responsible for equipment requiring AC power should consider including an advisory notice in
their customer information suggesting the customer use a surge arrestor. Telephone companies report
that electrical surges, typically lightening transients, are very destructive to customer terminal equip-
ment connected to AC power sources. This has been identified as a major nationwide problem.

HEARING AID COMPATIBILITY

NEC Multiline Terminals and NEC Single Line Telephones that are provided for this system are hearing
aid compatible. The manufacturer of other Single Line Telephones for use with the system must
provide notice of hearing aid compatibility to comply with FCC rules that now prohibit the use of
non-hearing aid compatible telephones.

MUSIC ON HOLD
IMPORTANT NOTE

"In accordance with U.S. Copyright Law, a license may be required from the American Society of
Composers, Authors and Publishers, or other similar organization, if radio or TV broadcasts are trans-
mitted through the Music On Hold feature of this telecommunication system. NEC Corporation of
America, hereby disclaims any liability arising out of the failure to obtain such a license."

RADIO FREQUENCY INTERFERENCE

In compliance with FCC Part 15 rules, the following statement is provided:

IMPORTANT NOTE

“This equipment generates, uses, and can radiate radio frequency energy and if not installed and used
in accordance with the System Hardware Manual, may cause interference to radio communications.
This equipment has been tested and approved for compliance with the limits for a Class B (except as
noted below) computing device pursuant to subpart J of Part 15 of FCC Rules, that are designed to

Hardware Manual R-3

SL1100 ISSUE 1.0

provide reasonable protection against such interference when operated in a commercial environment.
Operation of this telephone system in a residential area is likely to cause interference, in which case,
the user, at his or her own expense, is required to take whatever measures may be required to correct
the interference.”

When equipped with the 1228M/ME-B KSU, the SL1100 can be operated as a Class B device.

SAFETY INFORMATION
This equipment has been certified by CSA International and found to comply with all Applicable safety
requirements:
• CAN/CSA C22.2 No. 0-M – General Requirements – Canadian Electrical Code, Part II
• CAN/CSA C22.2 No. 60950-1-07 – Safety of Information Technology Equipment – Part l: General
Requirements
• UL 60950-1-SAFETY, 2nd Edition – Safety of Information Technology Equipment – Part I: General
Requirements

INDUSTRY CANADA REQUIREMENTS

Industry Canada has established rules that permit this telephone system to be directly connected to
the telephone network. Prior to the connection or disconnection of this telephone system to or from the
telephone network, the telephone company must be provided with the following information.

This product meets the applicable Industry Canada Technical Specifications/Le present material est
conforme aux specifications techniques applicables d’industrie Canada.
1. Your telephone number.
2. IC registration number: IC: 140L-SL1100
3. Ringer Equivalence Number (REN) of the equipment: 1.0B

Before installing this equipment, users should ensure that it is permissible to be connected to the facili-
ties of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, when present, are connected together. This
precaution may be particularly important in rural areas.

CAUTION

Users should not attempt to make such connections themselves, but should contact the applicable
electrical inspection authority or electrician.

The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to
be connected to the telephone interface. The termination on an interface may consist of any combina-
tion of devices subject only to the requirement that the sum of RENs of all the devices does not exceed
five/L’indice d’equivalence de la sonnerie (IES) sert a indiquer le nombre maximal de terminaus qui
peuvent etre raccordes a une interface telephonique. La terminaison d’une interface peut consister en
une combinaison quelconque de dispositifs, a la seule condition que la somme d’indices d’equivalence
de la sonnerie de tous les dispositifs n’excede pas 5.

This equipment meets Industry Canada Requirements in accordance with IC CS-03, issue 9 Part 1.

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital appa-
ratus as set out in the radio interference regulations of Industry Canada/Le present appareil numerique
n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de
Classe A prescrites dans le reglement sur le brouillage radioelectrique edicte par Industrie Canada.

R-4 Regulatory
ISSUE 1.0 SL1100

BATTERY DISPOSAL
The SL1100 system includes the batteries listed below. When disposing of these batteries, KSU,
and/or Unit, you must comply with applicable federal and state regulations regarding proper disposal
procedures.

Unit Name Type of Battery Quantity Note

IP4[ ]-CPU-B1 Lithium 1

External Battery Sealed Lead 2 per IP4WW-Battery Box

(IP4WW-Battery Box)

DTL-8R-1 Cordless Handset Ni-MH 1

ML440 Wireless Handset Lithium-ion 1

The SL1100 IP4[ ]-CPU-B1 provides memory backup for approximately three years. The Lithium
battery should be replaced every two years.

IMPORTANT SAFEGUARDS FOR BATTERY DISPOSAL

DO NOT PLACE USED BATTERIES IN YOUR REGULAR WASTE! THE PRODUCT YOU
PURCHASED CONTAINS LITHIUM, SEALED LEAD BATTERIES. LITHIUM, SEALED LEAD
BATTERIES MUST BE COLLECTED, RECYCLED, OR DISPOSED OF IN AN ENVIRONMENTALLY
SOUND MANNER.

The incineration, landfilling or mixing of sealed lead batteries with the municipal solid waste stream is
PROHIBITED BY LAW in most areas. Contact your local solid waste management officials for other
information regarding the environmentally sound collection, recycling, and disposal of the battery.

Sealed lead batteries must be returned to a federal or state approved sealed lead battery recycler. This
may be where the batteries were originally sold or a local seller of automotive batteries. Contact your
local waste management officials for other information regarding the environmentally sound collection,
recycling and disposal of the battery contained in this product.

The packaging for the SL1100 system contains the following labels regarding proper disposal.

CONTAINS SEALED LEAD BATTERY.

BATTERY MUST BE RECYCLED. MUST NOT
BE DISPOSED OF IN MUNICIPAL WASTE.

Pb

EUROPEAN UNION INFORMATION

Notice to the user
The system described in this manual is intended to be connected to analog and digital networks and
supports a wide range of peripheral equipment. The following interfaces are available for connection to
public analog and digital telecommunication networks:
• TBR3 ISDN basic rate interface
• TBR4 ISDN primary rate interface
• ES203-021 Analogue interface

To take advantage of all features of this system and the connected equipment, the country or network
specific features should match the supported features of the system. For an overview of the supported
features, refer to the detailed documentation that comes with this system, contact your local NEC
Unified Solutions representative or the support desk of NEC Unified Solutions.

Hardware Manual R-5

SL1100 ISSUE 1.0

Declaration of conformity
Hereby, NEC Unified Solutions, declares that the SL1100 is in compliance with the essential require-
ments and other relevant provisions of Directive 1999/5/EC.

For the Declaration of Conformity, visit: http://www.nec-unified.com/doc

Electromagnetic Compatibility
For the SL1100 system the following warning is applicable:

Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

PRODUCT DISPOSAL INFORMATION

For Countries in the European Union

The symbol depicted here has been affixed to your product to inform you that electrical and electronic
products should not be disposed of as municipal waste.

Electrical and electronic products including the cables, plugs and accessories should be disposed of
separately to allow proper treatment, recovery and recycling. These products should be taken to a
designated facility where the best available treatment, recovery and recycling techniques are available.
Separate disposal has significant advantages: valuable materials can be re-used and it prevents the
dispersion of unwanted substances into the municipal waste stream. This contributes to the protection
of human health and the environment.

Please be informed that a fine may be imposed for illegal disposal of electrical and electronic products
via the general municipal waste stream.

To facilitate separate disposal and environmentally sound recycling arrangements have been made for
local collection and recycling. If your electrical and electronic products must be disposed of please
refer to your supplier or the contractual agreements that your company has made upon acquisition of
these products.

At www.nec-unified.com/weee you can find information about separate disposal and environmentally
sound recycling.

R-6 Regulatory
ISSUE 1.0 SL1100

BATTERY INFORMATION
Defective or exhausted batteries should never be disposed of as municipal waste. Return old batteries
to the battery supplier, a licensed battery dealer or a designated collection facility. Do not incinerate
batteries. This product uses Lithium batteries. Do not use any other type.

For an overview of the location of batteries used in these systems, the battery replacement or removal
instructions, please refer to the SL1100 System Hardware Manual.

Hardware Manual R-7

SL1100 ISSUE 1.0

Memo

R-8 Regulatory
Introduction
SECTION 1 GENERAL INFORMATION
1
The SL1100 system is designed to support small/medium businesses with simple installation and easy
operation. The small compact KSU comes with an installed CPU and eight digital and four analog

Introduction
extension ports and has two stackable slots for further expansion.
Two more expansion KSUs provide a maximum of 36 analog trunks and 72 Multiline terminals. The
SL1100 is also equipped to support Digital Network (PRI, T1) and IP Trunks (SIP) or IP extensions.
Also, the SL1100 initially bundles Voice Mail and MEMDB.
KSU3
KSU2

IP/VoIP

KSU1
ISDN
Expanded

Embedded VRS/VM
R em ote P C
B ackup B attery

PSTN Audio Port

Extension Port

M ultiline IP Telephone

Office LAN/CTI
M ultiline Telephone (2-wire)
External Music Source
(E X M O H , B G M ..)
PC

D S S C onsole

E xternal P aging S ystem P C P ro/ W eb P ro

A nalog Telephone

C T I S erver

FA X

D oorB ox

Relay Control Port

P rinter
D oor O pener (General Purpose Relay)

Figure 1-1 System Configuration

Hardware Manual 1-1

SL1100 ISSUE 1.0

SECTION 2 EQUIPMENT LIST

The following table lists all equipment for the SL1100 system.

Stock Number Equipment Name Equipment Description Note

1100001 SL1100 TDM Basic Kit SL1100 Basic Kit (4x8x4)
(4x8x4) <Including> IP4NA-1228M-B KSU, IP4WW-4COIDB-B1,
IP4WW-12TXH-B-TEL (BK) (3 sets)

1100010 IP4NA-1228M-B KSU IP4NA-1228M-B KSU with AC Cable (for NA)

<Including> IP4NA-CPU-B1, IP4WW-084M-B1, Power
Supply, PZ-VM21, IP4NA-MEMDB-C1

1100011 IP4NA-1228ME-B EXP IP4WW-1228ME-B EXP with AC Cable

<Including> IP4WW-EXIFE-C1, IP4WW-084M-B1,
Power Supply

1100110 IP4WW-EXIFB-C1 Expansion KSU Interface Unit, 3 jacks (two only are
used)

1100114 IP4WW-Battery Box External Battery Box without Batteries

1100020 IP4WW-080E-B1 8 Digital Extensions Interface

1100021 IP4WW-008E-B1 8 Analog Extensions Interface

1100022 IP4WW-4COIDB-B1 4 Analog Trunks Interface, mounted on 084M-B1/080E-

B1/008E-B1 board

1100024 IP4WW-1PRIU-C1 1 Primary Rate Interface (PRI/T1)

1100111 IP4WW-VOIPDB-C1 16-channel VOIP on CPU

1100112 IP4WW-CFVMS-C1 Compact Flash for VRS and InMail ( Approx. 15 hours,
VRS: 4ch (default)/InMail: 2ch (default))

1100113 IP4WW-CFVML-C1 Compact Flash for VRS and InMail ( Approx. 40 hours,
VRS: 4ch (default)/InMail: 4ch (default))

1100060 IP4WW-12TXH-B-TEL 2-wire 12-key Multiline Telephone

(WH)

1100061 IP4WW-12TXH-B-TEL
(BK)

1100062 IP4WW-24TXH-B-TEL 2-wire 24-key Multiline Telephone

(WH)

1100063 IP4WW-24TXH-B-TEL
(BK)

1100160 IP4WW-24TIXH-C-TEL 24-Keys, Multiline IP Telephone

(WH)

1100161 IP4WW-24TIXH-C-TEL
(BK)

1100064 IP4WW-60D DSS-B 60-button Direct Station Selection (DSS) Console

CONSOLE (WH)

1100065 IP4WW-60D DSS-B

CONSOLE (BK)

721160 DP-D-1A Doorphone

922450 DX4NA Doorphone Doorphone

690631 AC-L UNIT AC/DC Adapter for 24TIXH TEL

780135 AC-2R UNIT AC/DC Adapter for 24TIXH TEL

1100080 SL-IP-SIPTRK-1 LIC SIP Trunk License (1 port)

1100089 SL-IP-SIPEXT-1 LIC Standard SIP Terminal License (1 port)

1100081 SL-IP-ENCRYPTION LIC Encryption License for Multiline IP Telephone (1 license

per system)

1100083 SL-VM-CHANNEL-2 LIC Additional InMail Channel License (2 ports)

1-2 Introduction
ISSUE 1.0 SL1100

Stock Number Equipment Name Equipment Description Note

1100084 SL-VM-ADVANCE LIC InMail Advanced Features License (1 license per
system)

1100085 SL-SYS-MOBILE-1 LIC Additional Mobile Extension Port License (1 port)

1100086 SL-SYS-HOTEL LIC Hotel/Motel Feature License (1 license per system)

1100082 SL-IP-CHANNEL-16 LIC Additional 16 DSP Resource License (1 license per

system)

1100162 IP4WW-WALL MOUNT Wall-Mount Unit for IP4WW-24TIXH-C-TEL

UNIT

730095 DTL-8R-1 Cordless Cordless DECT Handset

Handset

730639 DTL-RPT-1 Repeater Repeater for DTL-8R-1

730651 AP20 Base Unit Base Unit for ML440

730650 ML440 Multiline Wireless ML440 Multiline Wireless Handset

Handset

2.1 KSUs and Optional Unit

2.1.1 IP4[ ]-1228M-B KSU

The Main or controlling KSU is shipped fully assembled. The following are included with the KSU:

• CPU with main software (CPU-B1)

• Power supply (110V/240V)
• 1 External backup battery connector
• 2 mounting spaces for 080E/008E/1PRIU
• 8 digital and 4 analog extension I/F (084M-B1)
• 1 mounting space for 4COIDB-B1
• 1 slot for EXIFB-C1
• 2 general purpose relay
• 1 audio output for Paging (mini-jack)
• 2 audio inputs for ExMOH/BGM (mini-jack)
• SLT ringer
• Message waiting lamp driver
• 2ch Built-in Auto Attendant
• VMDB/MEMDB are initially equipped on the IP4NA-
CPU-B1.

The on-board DSP provides:

• 16 telephony resources (DTMF/Dial tone/Busy tone/FSK caller-ID receiver/sender)
• 128 tone sender resources (System tones sender/DTMF sender)
• 32 ch conference resources

2.1.2 IP4[ ]-1228ME-B EXP

A maximum of two additional 1228ME EXPs can be connected to expand the system capacity of the
1228M KSU. Although similar in shape and size as the 1228M KSU, the capabilities are not the same.
The following are included with the 1228ME EXP:

Hardware Manual 1-3

SL1100 ISSUE 1.0

• Power supply (110 V/240 V)

• 1 external backup battery connector
• 2 mounting spaces for 080E/008E/1PRIU
• 8 digital and 4 analog extension I/F (084M-B1)
• 1 mounting space for 4COIDB-B1
• EXIFE-C1 (1 connector for 1228M-B KSU)
• 2 general purpose relay
• 1 audio output for Paging (mini-jack)
• 2 audio inputs for ExMOH/BGM (mini-jack)
• SLT ringer
• Message waiting lamp driver

The EXIFE DSP provides:

• 32 telephony resources (DTMF/Dial tone/Busy tone/FSK caller-ID receiver/sender)

The 1228ME-B EXP does NOT have CPU and main software and cannot be used in a stand-alone
mode.

2.1.3 IP4WW-EXIFB-C1
Using a Cat5 cable, EXIFB-C1 card installed in the Main KSU
is individually connected to each EXIFE-C1 card (Expansion
KSU).
• Install this card to the Main KSU.
• Two connections for Expansion KSUs
(No.3 connector is not used).

2.1.4 IP4WW-Battery Box

Connected to each KSU power supply, the external backup
battery provides DC power in case a loss of AC power occurs.
An optional (locally procured), external battery source can be
used to provide power during a power failure.
• Connect this box to the power supply at each KSU.
• Wall/floor-mountable
• One KSU can be mounted on the Battery box.
• Backup duration is approximately one hour.

1-4 Introduction
ISSUE 1.0 SL1100

2.2 Trunk/Extension/ISDN Expansion Interface Cards

2.2.1 IP4WW-080E-B1
The 080E card is installed in the 1228M KSU or 1228ME EXP
and provides a total of eight digital ports. The analog trunk
daughter board (4COIDB) can be mounted on this card.
• Install this card to the expansion card slot at
Main/Expansion KSU.
• Enables the DSS console to connect to any extension port.
• One analog trunk daughter board connection.

2.2.2 IP4WW-008E-B1
This 008E card is installed in the 1228M KSU or 1228ME EXP
and provides a total of eight analog ports. The analog trunk
daughter board (4COIDB) can be mounted on this card.
• Install this card to the expansion card slot at
Main/Expansion KSU.
• One analog trunk daughter board connection.

2.2.3 IP4WW-4COIDB-B1
The 4COIDB provides four analog trunk and is mounted on the
084M, 080E or 008E card. A total of nine 4COIDBs can be
installed per system or three 4COIDBs per KSU.
• Mount this board onto the 084M, 080E or 008E card.
• 1 power failure transfer circuit

2.2.4 IP4WW-1PRIU-C1
The 1PRIU is installed in the 1228M KSU or 1228ME EXP
providing for either an ISDN Primary Rate Interface, T1 Inter-
face. A total of two 1PRIUs can be installed per system or one
1PRIU per KSU.
• Install this card to the expansion card slot at
Main/Expansion KSU.
• Supports T/S point connection (Hard-switch).

Hardware Manual 1-5

SL1100 ISSUE 1.0

2.3 Optional Interface Cards

2.3.1 IP4WW-VOIPDB-C1
The VOIPDB-C1 card provides the RTP/RTCP voice
processing function.
• Mount this card onto the CPU card (VoIPDB slot) at Main
KSU.
• Max. 32 channels by license control.

2.3.2 IP4WW-CFVMS-C1/IP4WW-CFVML-C1
Two types of VRS/VM CF cards are available:
• Install into the VMDB mounted on the CPU card at Main
KSU.
• CFVMS: VRS and 2-channel InMail (Approx. 15 hours)
• CFVML: VRS and 4-channel InMail (Approx. 40 hours)

2.4 Multiline Telephones and Optional Equipment

2.4.1 IP4WW-12TXH-B TEL

The 12TXH-B TEL is a 2-wire digital multiline telephone
featuring:
• Programmable keys: 12
• Soft Keys: 4
• LCD: 24 digits x 3 lines with Backlit
• Handsfree: Full-duplex
• Backlit dial pad: Yes
• Angle Adjustment: 2-steps
• Wall-Mounting kit: Built-in

2.4.2 IP4WW-24TXH-B TEL

The 24TXH-B TEL is a 2-wire digital multiline telephone
featuring:
• Programmable keys: 24
• Soft Keys: 4
• LCD: 24 digits x 3 lines with Backlit
• Handsfree: Full-duplex
• Backlit dial pad: Yes
• Angle Adjustment: 2-steps
• Wall-Mounting kit: Built-in

1-6 Introduction
ISSUE 1.0 SL1100

2.4.3 IP4[ ]-24TIXH-C TEL

The 24TIXH-C TEL is an IP multiline telephone featuring:
• Programmable keys: 24
• Soft Keys: 4
• LCD: 24 digits x 3 lines with Backlit
• Handsfree: Full-duplex
• Interface: 2 x RJ45 Ethernet Ports (10Base-T/100Base-TX)
for LAN and PC
• Power Feeding: AC Adapter (optional) or PoE (IEEE802.3af)
• Support CODEC: G.711/G.729a/G.722
• Backlit dial pad: Yes
• Angle Adjustment: 2-steps
• Wall-Mounting kit: IP4WW-WALL MOUNT UNIT (Optional)

2.4.4 IP4WW-60D DSS-B

The DSS console gives a multiline terminal user a Busy Lamp
Field (BLF) and one-button access to extensions, trunks and
system features. Mainly designed for operator use, the
60-button DSS console provides an additional 60 program-
mable keys.
• Connect this console to digital extension port at
084M/080E of each KSU.
• Programmable keys: 60
• Angle Adjustment: 2-steps
• Wall-Mounting kit: Built-in

2.4.5 DP-D-1D
This is the Doorphone Box.
• Connects to analog port number 3 or 4 on the 084M of
each KSU.

Hardware Manual 1-7

SL1100 ISSUE 1.0

2.5 Wireless DECT Telephones

2.5.1 DTL-8R-1 Cordless DECT Telephone
DTL-8R-1 is a single-cell cordless DECT telephone that is
adapted for digital NEC SL1100 system. It is designed for use
in the office environment.
The following are included with the DTL-8R-1 Cordless DECT
Telephone.
• DTL-8R-1 Base Unit
• DTL-8R-1 Cordless Handset

2.5.2 DTL-RPT-1 Cordless DECT Telephone Repeater

DTL-RPT-1 is a repeater to extend the coverage area of
DTL-8R-1 Cordless DECT telephone system in all directions.

2.5.3 ML440 and AP20 Wireless DECT Telephone

ML440 and AP20 is a multi-cell wireless DECT telephone that
is adapted for digital NEC SL1100 System. It is designed for
use in the office environment.
The following are included with the ML440 Wireless DECT.
• AP20 Base Unit
• ML440 Wireless Handset

1-8 Introduction
ISSUE 1.0 SL1100

SECTION 3 SYSTEM CAPACITY

3.1 System Capacity

Table 1-1 System Capacity

Items 1 KSU 2 KSU 3 KSU Note

(1228) (2456) (3684)
Expansion Slot 2 4 6

System Maximum Port 52 104 144 1KSU: 084M+PRI+080E+4COIDBx2

2KSU: (084M+PRI+080E)x2+4COIDBx4
3KSU: 084Mx3+PRIx2+080Ex4+4COIDBx7

Trunk Port Max. 32 64 76 1KSU: PRIx1+4COIDBx2

2KSU: PRIx2+4COIDBx4
3KSU: PRIx2+4COIDBx7

Trunk Port Analog Trunks 12 24 36 1KSU: 4COIDBx3 on 084M/080E/008E

(COT) 2KSU: 4COIDBx6
3KSU: 4COIDBx9

PRI (24B) 24 48 48 Max. one PRI/KSU

Max. two PRIs/system

IP Trunk (SIP) 32

Station Port Max. 28 56 84 1KSU: 084M+080Ex2

2KSU: 084Mx2+080Ex4
3KSU: 084Mx3+080Ex6

Station Port 2W Key Set 24 48 72 Max. 24/KSU

084M+080Ex2

SLT (–28V) 20 40 60 1KSU: 084M+008Ex2

2KSU: 084Mx2+008Ex6
3KSU: 084Mx3+008Ex9

2W DSS Console 12 Connect to digital extension Port at

084M/080E

Doorphone 2 4 6 2DPH I/F on 084M (analog extension port 3,

4)
Alternative use with SLT

SIP-MLT/ SIP Std. 64

terminal

VM/VRS 2 VM ports/ 4 VRS ports (default) CFVMS-C1

Channels (Total Max.16) Port increased by license.

4 VM ports/ 4 VRS ports (default) CFVML-C1

(Total Max.16) Port increased by license.

Virtual Extension 50

Relay 2 4 6 2 circuits on 084M

Power Failure Transfer 3 6 9 1 PFT circuit on 4COIDB (COI port 1 and PF

port)

External Paging (Audio Out) 1 2 3 1 audio-In/Out and 2 audio-In circuits on

084M.
External MOH (Audio In) 1 Select one of 084M for MOH/BGM.

External BGM (Audio In) 1

Ethernet Port 1 1 circuit on CPU

Built-In Answering Machine 2 2 circuits on CPU

Channel

VoIP Channels 32 Port increased by license.

V.34 Modem 1 1 circuit on CPU-B1 (VMDB)

Conference Circuits 32 (Max. 16 parties per Conference)

Hardware Manual 1-9

SL1100 ISSUE 1.0

Items 1 KSU 2 KSU 3 KSU Note

(1228) (2456) (3684)
DSP Resource *1 32 For 1228M KSU (DSP on CPU)

- 32 64 For 1228ME EXP 32ch DSP on each

EXIFE-C1

DSP Sender*2 128

*1. Service Tone receiver, DTMF receiver, Caller ID sender / receiver, MF receiver, MFC receiver
*2. Service Tone sender, DTMF sender, MF sender, MFC sender

3.2 KSU Capacity

System image of KSU capacity (ISDN, Trunk, Extension) is shown as below.

Expansion
Interface Card x 2
Mother Board Mother Board
084M*1 : Digital Extension x 8, Analog Extension x 4

Expansion Interface Card

080E*1 : Digital Extension x 8
008E*1 : Analog Extension x 8
1PRIU : ISDN PRI x 30
Main KSU (1228M-B) *1. Optional 4COIDB Analog Trunk x 4

Expansion
Interface Card x 2

Mother Board

Expansion KSU (1228ME-B) x 2

Figure 1-2 System Image

1-10 Introduction
ISSUE 1.0 SL1100

3.2.1 Expandability of Trunk and Extension (without PRI)

(Trunk)
36

24
1228ME EXP
(2nd exp. KSU)
1228ME EXP
12 (1st exp. KSU)
1228M KSU
(Extension)
28 56 84

Detail of one KSU

Example 1: 084M + 4Trk, (8Ext + 4Trk) x 2
12

8 080E or 008E +
1 KSU 080E or 008E + 4COIDB
4 4COIDB (2nd opt. slot)
084M + (1st opt. slot)
4COIDB
12 20 28
Example 2: 084M + 4Trk, 8Ext + 4Trk, 8Ext
8
080E or 008E +
1 KSU 080E or 008E
4 4COIDB
084M + (2nd opt. slot)
(1st opt. slot)
4COIDB
12 20 28

Example 3: 084M + 4Trk, 8Ext

4
084M + 080E or 008E
1 KSU 4COIDB (1st opt. slot)
12 20
Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI)

Hardware Manual 1-11

SL1100 ISSUE 1.0

3.2.2 Expandability of Trunk and Extension (with PRI)

(Trunk) Max 2PRI in three KSUs.

76

64
1228ME EXP
(2nd exp. KSU)
1228ME EXP
32 (1st exp. KSU)
1228M KSU
(Extension)
20 40 68

Detail of PRI installed KSU

Example 1: 084M + 4Trk, 8Ext + 4Trk, PRI x 1
32

PRI
(2nd opt. slot)
1 KSU

8
080E or 008E +
4 4COIDB
084M +
4COIDB (1st opt. slot)

12 20
Example 2: 084M, PRI x 1
24

PRI (1st opt. slot) +

1 KSU 084M

4
12
Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI)

1-12 Introduction
Installation
SECTION 1 INSTALLING THE MAIN & EXPANSION KSUS
2
1.1 Before Installing the KSU(s)

Installation
1.1.1 General Precautions
• To avoid shock or equipment damage, do not plug in or turn the system power on before completing
the installation process.
• Avoid working with the Equipment during electrical storms.
• Use only commercial AC power to prevent shock or fire.
• Use the power cord supplied with the KSU.
• Install batteries with the correct polarity to prevent damaging equipment.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet loca-
tions.
• Never touch uninsulated telephone wires or terminals unless the telephone line is disconnected at
the network interface.
• To avoid damage, the KSU should not be placed on unstable surfaces.
• To prevent overheating, do not bundle AC power cords together.
• Make sure the KSU has proper Earth ground.
• If Expansion KSU(s) are installed, turn the power on/off in the following order:
Expansion 2 KSU, Expansion 1 KSU and then Main KSU

1.1.2 Preparations
• Make sure the necessary tools (screw driver set, pliers set, etc) are available.
• Make sure you have a building plan showing common equipment, extensions, the telecom demarca-
tion, and earth ground location. The installation site must meet the following site / environmental
requirements.

1.1.3 Site Requirements

Each Main or Expansion KSU(s) can have the optional Battery Box connected, before deciding on the
mounting location refer to Figure 2-4 Horizontal Arrangement of the KSUs on page 2-5 and
INSTALLING THE EXTERNAL BACKUP BATTERY on page 2-17.
• The system without the IP4WW-Battery Box should be wall-mounted only. The system with the
IP4WW-Battery Box can be installed on either the floor or wall (horizontally). Ensure enough space
exists to allow the installation of additional KSU(s) and/or battery box.
• A dedicated 100V-120V/220V/230V/240VAC circuit located within two meters of the KSU is required.
A separate dedicated AC outlet is necessary for each KSU.

1.1.4 Environmental Requirements

Meeting established environmental standards maximizes the life of the system. Make sure that the site
is not:
• In direct sunlight or in hot, cold or humid places.
• In dusty areas or in areas where sulfuric gases are produced.
• In places where shocks or vibrations are frequent or strong.
• In places where water or other fluids comes in contact with the equipment.

Hardware Manual 2-1

SL1100 ISSUE 1.0

• In areas near high-frequency machines or electric welders.

• Near computers, telexes, microwaves, air conditioners, etc.
• Near radio antennas (including shortwave).

1.1.5 Unpacking

Unpack the KSU and check it against the following list. Inspect for physical damage.

Table 2-1 KSU Packing List

Items List of Contents QTY

1228M-B KSU 1228M-B KSU 1

AC Power Cord 1

Screws (M4.1x25) 4

Wall-Mounting Template 1

1228ME-B EXP 1228ME-B EXP 1

AC Power Cord 1

Screws (M4.1x25) 4

Expansion Cable 1

Wall-Mounting Template 1

1.2 Installing the Main KSU (1228M-B KSU)

The Main KSU has a CPU-B card, an eight digital and four analog extension Interface, a control relay
circuit for External devices, and two mounting spaces for optional cards (080E-B1/008E-B1/1PRIU-
C1).

An Expansion KSU can be added increasing system capacity. Each KSU (Main or Expansion) is
powered by its own power supply.
Tab
CPU card
Sub-Cover
S1

Tab
LOAD SERIAL
EXP3

EXP3

VOIP

VOIP
EXP2

EXP1 EXP2

J3
EXP1

LAN

< Front view >

Figure 2-1 CPU Card Location

Table 2-2 Items on the CPU card

Item Description
S1 (LOAD) Switch for System Restart/System Reset (Cold start occurs)/Upload Software

2-2 Installation
ISSUE 1.0 SL1100

Item Description
Ethernet Cable Connection (for SMDR (PC, Printer), PCPro or WebPro….etc)

Pin No. Connection

1 Tx+
J3 (RJ45) 2 Tx-

3 Rx+

4 -

8 765 4321 5 -

6 Rx-

7 -

8 -

For the detail of LED (D1 - D5), refer to Figure 4-17 Inserting the CF Card on page 4-10 and
Table 4-2 CPU LED Indications on page 4-12.

1.3 Wall-Mounting the KSU(s)

1.3.1 KSU Dimensions

For Dimensions of the 1228M-B and 1228ME-B KSUs, refer to Figure 2-2 Dimension of the Main and
Expansion KSU on this page.

290 mm
(11.417″)

115 mm
(4.528″)

375 mm (14.764″)
Figure 2-2 Dimension of the Main and Expansion KSU

Hardware Manual 2-3

SL1100 ISSUE 1.0

1.3.2 Wall Installation of KSU

The Main KSU (1228M-B) and Expansion KSU(s) (1228ME-B) be mounted on the wall. Before
installing, ensure the appropriate spacing exists as shown below. In case of horizontal arrangement,
refer to Mounting one KSU on the Battery Box on page 2-30 for mounting on the IP4WW-Battery Box.
Ceiling

Minimum 200 mm
(7.874″)
for ventilation
EXP. KSU

Minimum 100 mm (3.937″)

for ventilation and wiring Main KSU Minimum 300 mm
Minimum 300 mm (11.811″) (11.811″)
Wall

Minimum 100 mm (3.937″)

for ventilation and wiring EXP. KSU

Minimum 200 mm
(7.874″)
for wiring

Floor

Figure 2-3 Vertical Arrangement of KSUs

• Due to the limit of extension cable length to connect Main KSU and Expansion KSU(s), the install location of
Main KSU and each Expansion KSU(s) must be considered as above or as the next figure.
• When KSU is mounted on the Battery Box, it cannot be wall-mounted for vertically as above.
• In the case, the KSU is mounted on Battery Box must be wall-mounted horizontally as shown on the
Figure 2-4 Horizontal Arrangement of KSUs on the next page.

2-4 Installation
ISSUE 1.0 SL1100

Ceiling

Minimum 200 mm (7.874″)

for ventilation

Minimum Minimum Minimum Minimum

300 mm 100 mm 100 mm 300 mm
(11.811″) (3.937″) (3.937″) (11.811″)

Wall

EXP. KSU Main KSU EXP. KSU

Minimum 200 mm (7.874″)

for ventilation

Floor
Figure 2-4 Horizontal Arrangement of KSUs
Due to the limit of extension cable length to connect between Main KSU and Expansion KSU(s), the install
location of Main KSU and each Expansion KSU(s) must be considered as Figure 2-4 Horizontal Arrangement
of KSUs on this page.

1.3.3 Mounting Procedure of KSU

One Main KSU or Expansion KSU(s) can be mounted per IP4WW-Battery Box. For the mounting, refer to
Mounting one KSU on the Battery Box on page 2-30.
1. Place the attached template on the wall to mark the four screw positions.

Template

UP

Figure 2-5 Wall-Mounting Template

2. Install four screws into the wall. The screw heads must stand off from the wall about 2.5 mm
(0.098″) to 3.5 mm (0.138″).

Hardware Manual 2-5

SL1100 ISSUE 1.0

2.5 mm (0.098″) -
285 mm (11.221″) 3.5 mm (0.138″)

180 mm
(7.087″)

285 mm (11.221″)
Figure 2-6 Screw Positions
• Wall-Mounting Screws (M4.1x 25: 4 pcs) are attached to the KSU.
• The screw diameter is 4 mm (0.158″) to 4.5 mm (0.177″).
3. Push the center of the Sub-Cover and slide it outward.

Sub-Cover
Figure 2-7 Sub-Cover Slide-out
4. Pull out the Sub-Cover by pushing out the tabs.

Tab

Sub-Cover

Tab

Figure 2-8 Removing the Sub-Cover

2-6 Installation
ISSUE 1.0 SL1100

• The Sub-Cover can be opened and held in the open position.

Push to hold

Open

Figure 2-9 Sub-Cover Open Position

5. Align the four holes on the back of the KSU with the four screws installed in the wall.

Screw head

Hook

Fasten screws
Screw head
Figure 2-10 Mounting the KSU
6. Slide the KSU into position and tighten the lower two screws.

1.4 Installing the Expansion KSU(s)

1.4.1 General

Each Expansion KSU is connected to the Main KSU individually. The EXIFB-C1 card must be installed
in the Main KSU (1228M-B).

1.4.2 Unpacking (EXIFB-C1)

Unpack the EXIFB-C1 and check it against physical damage.

Table 2-3 EXIFB-C1 Packing List

Items List of Contents QTY

EXIFB-C1 EXIFB-C1 PCB 1

Hardware Manual 2-7

SL1100 ISSUE 1.0

1.4.3 Connectors Location (EXIFB-C1)

J5 J6
J1

J2

J3

J4
Figure 2-11 Connectors of EXIFB-C1
Table 2-4 Connectors of EXIFB-C1

No. Connectors Connectable Devices

J1 Expansion Connector (Not used) -

J2 Expansion Connector Expansion KSU 2

J3 Expansion Connector Expansion KSU 1

J4 Mother PCB J1 connector on 084M-B1

J5, J6 Debug Purpose (Not used) -

1.4.4 Installing the EXIFB-C1 PCB

Do Not Power on until all installations have been completed.

1. Turn off the system power and disconnect the AC cord from KSU.
2. Open and pull out the Sub-Cover of the Main KSU.

Tab

Sub-Cover

Tab

Sub-Cover

Figure 2-12 Removing the Sub-Cover

3. Loosen two screws and pull out the Main-Cover by pressing the two hooks.

2-8 Installation
ISSUE 1.0 SL1100

Main-Cover
Two screws

Hooks

Figure 2-13 Removing the Main-Cover

4. Press tab A and lift the CPU support bracket.

EXIFB-C1 PCB
CPU support
CPU support

084M-B1 at 1228M KSU

J1
Figure 2-14 EXIFB-C1 PCB Installation
5. Insert the EXIFB-C1 PCB into the J1 connector on the 084M-B1 at 1228M-B KSU.
6. Close the CPU support and make sure the tab A locks into place.
7. Cut and remove the Plastic Knockouts as needed for Expansion KSU.

Main-Cover

Plastic Knockouts

Figure 2-15 Removing the Plastic Knockouts

8. Replace the Main-Cover and fasten two screws.

Hardware Manual 2-9

SL1100 ISSUE 1.0

Main-Cover
Two screws

Hooks

Figure 2-16 Replacing the Main-Cover

1.4.5 KSUs Inter-connection

1. Connect the Main KSU (1228M-B) and Expansion KSU (1228ME-B) using the cables attached to
the Expansion KSU. The cable must pass two times (two rounds) through the Ferrite Core refer to
Figure 2-17 Connection of KSUs on the next page. (Ferrite Core is attached with the Expansion
KSU.)

2-10 Installation
ISSUE 1.0 SL1100

Exp. KSU No.1 (1228ME-B)

EXIFE-C1 PCB

Pass 2 times

EXP
Ferrite Core
< Bottom View >

Main KSU (1228M-B)

EXIFB-C1 PCB CPU card

EXP 2
EXP 1

LAN
< Bottom View >
Exp. KSU No.2 (1228ME-B)
EXIFE-C1 PCB

Pass 2 times

EXP

Ferrite Core
< Bottom View >
Figure 2-17 Connection of KSUs
Use attached cables for the above inter-connection.
Because of cable length, KSU positioning is limited.

30 - 50 mm
EXIFE-C1 PCB (1.181″ - 1.969″)

LAN Cable
Ferrite Core
Pass 2 times

to Main KSU

Exp. KSU
< Bottom View >
Figure 2-18 Installing Ferrite Core

Hardware Manual 2-11

SL1100 ISSUE 1.0

1.5 Grounding and AC Cabling

The ETH (Earth Ground Lug) is located near the power supply on each KSU. The Sub-Cover must be
opened in order to access to it.

1.5.1 Grounding the KSU

Ensure all Main and Expansion KSU(s) are powered off and unplug the AC cord.

In each KSU, connect the ETH lug to the verified grounding point using a minimum cable size of
14AWG (Φ2.0 mm) wire.

Screw

To Earth
ETH Lug

Figure 2-19 ETH Lug

• The grounding cable is supplier-provided.(not attached to the system)
1. Loosen the screw.
2. Insert a grounding wire (user supplied).
3. Tighten the screw.
4. Connect the grounding wire to earth ground.

Proper grounding is very important to protect the system from external noise
and to reduce the risk of electrocution in the event of a lightning strike.
1.5.2 AC Power Requirement

A dedicated 100V-120V/220V/230V/240V 50/60Hz circuit located within two meters of the KSU is
required. A separate dedicated AC outlet is necessary for each KSU.

Double Pole/Neutral Fusing

(Power supply fuses are located at both the L and N side.)

Table 2-5 Power Requirement

110VAC 120VAC 220VAC 230VAC 240VAC

Power Requirement 110 VAC@15 A 120 VAC@15 A 220 VAC@15 A 230 VAC@15 A 240 VAC@15 A

Power Consumption Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
128 VA 130 VA 154 VA 154 VA 156 VA

3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total = 3KSU Total =
384 VA 390 VA 462 VA 462 VA 468 VA

Input Voltage (Rated Voltage) 90 VAC to 264 VAC (100VAC/120VAC/220VAC/230VAC/240VAC)

Frequency 47 Hz - 63 Hz (Rated Frequency: 50/60 Hz)

Phase and Wire Single Phase, 2 Line + PE Type

2-12 Installation
ISSUE 1.0 SL1100

110VAC 120VAC 220VAC 230VAC 240VAC

Ground Requirement No.14 AWG Copper Wire

Feeding Voltage SLT: 20 mA/ -27 V

AC Input I Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
1.16 A 1.08 A 0.70 A 0.67 A 0.65 A
3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total =
3.48 A 3.24 A 2.10 A 2.01 A 1.95 A

KWh Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
0.128 KWh 0.130 KWh 0.154 KWh 0.154 KWh 0.156 KWh
3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total
=0.384 KWh =0.390 KWh =0.462 KWh =0.462 KWh =0.468 KWh

BTU (KWh x 3413) Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
437 BTU 444 BTU 526 BTU 526 BTU 532 BTU
3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total
=1311 BTU =1332 BTU =1578 BTU =1578 BTU =1596 BTU

1.5.3 AC Power Cord

The AC power switch and AC power inlet are located at the left side of each KSU. The AC power cord
is connected to the AC inlet and the commercial AC power socket.

Do not plug-in AC power cord if the KSU Cover is removed.

Before connecting the AC power cord, make sure:

• The power switch at the left side of each KSU is turned OFF.
• The power switch at the commercial AC power socket is turned OFF.
• The AC plug fits the commercial AC power socket. The plug adapter is neces-
sary if it does not fit.

Connect

“B” type

To Commercial
AC Power Socket

AC Power Cord KSU

Figure 2-20 AC Power Cord

• Each KSU must have its own commercial AC power socket.
• DO NOT POWER ON until all KSU installation has been completed.

1.6 Trunk/Extension Cabling

1.6.1 General
The system provides RJ61 modular jacks for analog trunk and analog/digital extension connections.

1.6.2 Precautions for Cabling

• Do not wire the cable with an AC cable, computer, etc.

Hardware Manual 2-13

SL1100 ISSUE 1.0

• Do not run the cable near a high frequency generating device.

• Use cable protectors in case the cables are run on the floor.
• Aerial distribution wiring is not allowed.
• Trunks must be installed with lightning protectors.
• Do not install the DSX Terminal in the SL1100 system, it does not work properly.

1.6.3 Trunk Cabling

Trunk cabling is required for the 4COIDB or 1PRIU PCBs.

Refer to INSTALLING THE EXPANSION INTERFACE CARDS on page 2-38 for mounting and cabling
4COIDB and 1PRIU PCBs.

1.6.4 Extension Cabling

The 084M-B1 PCB within each KSU provides two "RJ61" modular jacks for digital extension (8ports)
and one for analog extensions (4ports).

Before plugging in the Multiline Telephone, DSS Console, Single line Telephone
or Doorphone, ensure all Main and Expansion KSUs are powered off.

DSX Terminal does not work properly when it connected.

J421
J103 J431 J411
J102 J101 J7

ESI 5-8 ESI 1-4

5 43 6 2 7 1 8

Port 1 Port 2 Port 3 Port 4

T R T R
T: Tip Max cable length
R: Ring 24AWG ( 0.5 mm)
Modular Cable
(2-wire, Straight) 300 m
MLT, DSS (984.3 ft)

Exit Help

ABC DEF
Flash Transfer
1 2 3
GHI JKL MNO
Mute DND
4 5 6
PQRS TUV WXYZ
Clear/Back
7 8 9
0 㧏
Speaker Hold

Multiline Telephone DSS Console

Figure 2-21 Digital Extension Cabling

2-14 Installation
ISSUE 1.0 SL1100

J421
J103 J431 J411
J102 J101 J7

SLI 9-12
/DPH 1-2

5 43 6 2 7 1 8

Port 1 Port 2 Port 3 Port 4

T : Tip T R T R T R
R : Ring
Modular Cable
Max cable length (2-wire, Straight)
24AWG ( 0.5 mm)
1,125 m
SLT (3,691 ft)
150 m
Doorphone (492.1 ft)

5 6

䂯 䂥

SLT Doorphone External

Sensor Device
Figure 2-22 Analog Extension Cabling

While a Digital/Analog Telephone (port) is ringing or MW-lamp is flashing on a

Digital/Analog Phone (port), do not disconnect the phone from the port or
connect another type of the terminal to this port.

• Doorphone/External Sensor Device must be connected to the No. 3 or 4 PORT of the RJ61 connector for
Analog extensions on each 084M-B1.
• Setting program 10-03 to "Door Phone" is required when connecting a Door phone Box or Sensor device.

1.6.4.1 Connectors

The following table shows the pin-outs for the RJ-61 cable connector for Digital/Analog extension
connections.

Hardware Manual 2-15

SL1100 ISSUE 1.0

Table 2-6 RJ61 Cable Connector Pin-Outs (J101-J103)

Pin No. ESI 1-4 (J101), ESI 5-8 (J102): SLI 9-12/DPH 1-2 (J103): Analog
2-Wire Digital Extension Port Extension Port Connector
Connector (RJ-61) (RJ-61)
1 T4 (Tip for port 4) T4 (Tip for port 4)

2 T3 (Tip for port 3) T3 (Tip for port 3)

3 T2 (Tip for port 2) T2 (Tip for port 2)

8 765 4321 4 R1 (Ring for port 1) R1 (Ring for port 1)

5 T1 (Tip for port 1) T1 (Tip for port 1)

6 R2 (Ring for port 2) R2 (Ring for port 2)

7 R3 (Ring for port 3) R3 (Ring for port 3)

8 R4 (Ring for port 4) R4 (Ring for port 4)

1.6.5 Cable Routing and Clamping

1. Depending on cabling requirement, select either a right or left route. Clamp and route cable to
outside.

Cable clamp

Cables

Figure 2-23 Cabling

2. Cut and remove the Plastic Knockouts as needed from the Sub-Cover.

Sub-Cover

Plastic Knockouts
Figure 2-24 Sub-Cover
3. Replace the Sub-Cover.

2-16 Installation
ISSUE 1.0 SL1100

SECTION 2 INSTALLING THE EXTERNAL BACKUP BATTERY

2.1 General

The external backup battery box (IP4WW-Battery Box) with batteries provides power to the system
when AC power fails. It is connected to the power supply of each KSU.

• An optional (locally procured), external battery source can be used to provide power during a power failure.
• Each KSU must have own IP4WW-Battery Box.

To avoid damage to equipment, do not install the Topaz Battery Box (DX2E-
32i/NX7E Battery Box) to the SL1100 system.

2.2 Unpacking

Unpack the IP4WW-Battery Box and check it against the following list. Inspect for physical damage.

Table 2-7 IP4WW-Battery Box Packing List

Items List of Contents QTY

IP4WW-Battery Box Battery Box 1

Battery Connection Cable (Black & Red) 1

Battery Connection Cable (Blue) 1

Screws: M4 x 8 10
M3 x 6 with Washer 1
Screws: M4.1 x 16 6

Battery Box FM/WM Base-F 1

Battery Box FM/WM Base-R 1

Battery Box WM Support 1

Battery Box WM Hook 1

Hardware Manual 2-17

SL1100 ISSUE 1.0

2.3 Battery Box Dimensions

230 mm
(9.055″)

340 mm
(13.386″)

500 mm (19.685″)
Figure 2-25 Dimension of the IP4WW-Battery Box

2.4 Battery Specifications

Table 2-8 Battery Specifications

Item Data
Capacity 12 V, 7.0 Am/H or equivalent (Voltage must be 12 V)

Recommended Battery GS Yuasa NP7-12 (151 x 65 x 97.5 mm / 2.7 kg)

<GS Yuasa International LTD.>
The Battery must be UL recognized product.

Number of Batteries (per Box) 2

Backup Duration (Estimated) 1 hour

2.5 Battery Installation

Before floor-mounting or wall-mounting the IP4WW-Battery Box, the batteries must be installed into the
IP4WW-Battery Box.
1. Loosen two screws and remove the Front Cover.

2-18 Installation
ISSUE 1.0 SL1100

Two screws
(with stopper)

Front Cover

Figure 2-26 Removing the Front Cover

2. Disconnect the Battery Connection Cable from the Fuse Unit if the cable is plugged already.

Battery Connection Cable

Fuse Unit

Figure 2-27 Disconnect Battery Connection Cable

3. Loosen the screw and lift the Batt Stopper.

Hardware Manual 2-19

SL1100 ISSUE 1.0

Batt Stopper

Screw

Figure 2-28 Batt Stopper

4. Pull out the Battery tray.

Battery tray

Figure 2-29 Pulling out the Battery Tray

5. Loosen two screws and remove the Battery tray cover.
6. Remove two screws and remove the Battery tray bracket.

2-20 Installation
ISSUE 1.0 SL1100

Two screws
(with stopper)

Battery tray cover

Two screws
(M3 X 8) Battery tray bracket

Figure 2-30 Remove the Battery Tray Bracket

7. Install two batteries into the Battery tray.

Two screws
Battery tray bracket (M3 X 8)

Two batteries

Figure 2-31 Battery Installation

8. Connect the battery cables.

Hardware Manual 2-21

SL1100 ISSUE 1.0

Battery Connection Cable (black)

Terminal Terminal
(black) (black)

Battery Connection
Cable (red)
Terminal
Terminal (red)
(red)
Battery Connection
Cable (blue)
< Front View > Two batteries

Figure 2-32 Connecting the Battery Cables

Incorrect installation of batteries may damage the Fuse Unit or cause possible
fire.
9. Insert Battery Connection Cable into the Cable guides as shown in the next diagram.
10. Install the Battery tray cover aligning the three tabs and tightening the two screws.

Two screws
Three tabs (with stopper)

Battery tray cover

Battery
Connection Cable
Cable guides
Figure 2-33 Installation of Battery Tray Cover
• Do not pull the Battery connection cable strongly.
• Be careful not to catch the Battery Connection Cable when installing the
Battery tray cover.

Write down the year and month of the next battery replacement in the label on Front cover.

11. Insert the Battery tray into the Battery Box.

2-22 Installation
ISSUE 1.0 SL1100

Battery tray

Figure 2-34 Inserting the Battery Tray

12. Set the Batt Stopper bracket in place and secure with screw.

Batt Stopper

Screw

Figure 2-35 Secure Batt Stopper Bracket

13. Plug the Battery Connection Cable into the Fuse unit.

Hardware Manual 2-23

SL1100 ISSUE 1.0

Battery Connection
Cable

Fuse unit

Figure 2-36 Connecting the Battery Connection Cable

14. Align tabs a to f to holes A to F on Battery Box. Slide the Front cover and tighten the two screws.

D E
f
b
B

c
C
a A
e

Front cover

Two screws
(with stopper)
Figure 2-37 Installation of Front Cover

2.6 Mounting the IP4WW-Battery Box

The IP4WW-Battery Box can be installed on either the floor or wall. One KSU can be mounted on an
IP4WW-Battery Box.

2.6.1 Floor-Mounting the IP4WW-Battery Box

Battery box can be mounted on the floor using the FM/WM Base-F, FM/WM Base-R and WM Support.
(Note: FM = Floor-Mount and WM = Wall-Mount)
1. Assemble the FM/WM Base-F, Base-R and WM Support.

2-24 Installation
ISSUE 1.0 SL1100

FM/WM Base-R
WM Support

FM/WM Base-F

Figure 2-38 Bases and Support of the Battery Box

2. Refer to Figure 2-39 Floor-Mount Spacing Guide on this page for required spacing before drilling
holes for 10 mm (0.394″) anchor bolts (locally procured).
Mark and drill the four holes required to install the FM/WM Base.
3. Using anchor bolts, secure the FM/WM Base to the floor.

Four Anchor bolts

M10 mm (0.394!)

Wall
AC inlet
side
)
5!
68
9.
(1
m

Anchor bolt location

15 .9
m

(5

46
0 06
0
50

m !)

0
m

m
m
(1
8.
11

80 m

Front side
.4 m
0

!)
!)

(7 90
1

: Maintenance space

Figure 2-39 Floor-Mount Spacing Guide

4. Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box on the Base.

Hardware Manual 2-25

SL1100 ISSUE 1.0

IP4WW-Battery Box

Hooks
FM/WM Base
Hooks

Figure 2-40 Mounting the Battery Box

5. Using four supplied screws, secure the IP4WW-Battery Box to the FM/WM Base.

IP4WW-Battery Box

Two Screws
(M4 X 8)

FM/WM Base

Two Screws
(M4 X 8)

Figure 2-41 Securing the Battery Box

2.6.2 Wall-Mounting the IP4WW-Battery Box

When wall-mounting the IP4WW-Battery Box, ensure the wall can support the
weight of the Battery Box (Total weight=17.6 kg (620.75 oz) - Including
2-batteries, cord, KSU, etc). The Battery Box is secured to the wall using the
FM/WM BASE. Ensure that enough space is available to allow the installation
of additional KSU.

Plywood should first be installed on the wall where the Battery Box will be positioned. This allows secure
anchoring of the screws which support the weight of the Battery Box.

2-26 Installation
ISSUE 1.0 SL1100

1. Using four supplied screws, secure the WM Support to the FM/WM Base-F and Base-R.

Four Screws
(M4 X 8)

WM Support

FM/WM Base-R

FM/WM Base-F

Figure 2-42 Assemble Battery Box Base

2. Refer to Figure 2-43 Wall-Mount Spacing Guide on the next page for required spacing before
drilling holes for 10 mm anchor bolts (locally procured).
Mark and drill the four holes required to install the FM/WM Base.
3. Using anchor bolts, secure the FM/WM Base to the wall.

Hardware Manual 2-27

SL1100 ISSUE 1.0

500 mm (19.685!)
Wall Front side
m
0m)
15 906!
(5.

Anchor bolt location

AC inlet
side
460 mm (18.110!)

Anchor bolt location

4!)
3 .50
(1 Four Anchor bolts
3 mm M10 mm (0.394!)
34
: Maintenance space

Figure 2-43 Wall-Mount Spacing Guide

4. Loosen two screws and remove the Front Cover.

2-28 Installation
ISSUE 1.0 SL1100

Two screws
(with stopper)

Front Cover

Figure 2-44 Removing the Front Cover

5. Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box to the Base.

Square hole

Hooks
A IP4WW-Battery Box
a

b
B

Hooks
E
d
c C

Figure 2-45 Mounting the Battery Box

6. Using one supplied screw (M3x6 with washer), secure the back plane of the Battery Box to the
FM/WM Base.

Hardware Manual 2-29

SL1100 ISSUE 1.0

Two screw holes

(Use either one)

< Front view>

Figure 2-46 Securing the Battery Box

2.6.3 Mounting One KSU on the Battery Box

Before wall-mounting or floor-mounting the IP4WW-Battery Box, a single KSU can be mounted on the
Battery Box.
1. Loosen two screws and remove the Front Cover of the Battery Box.

Two screws
(with stopper)

Front Cover

Figure 2-47 Removing the Front Cover

2. Loosen two screws and remove the L-Bracket.

2-30 Installation
ISSUE 1.0 SL1100

L-Bracket

Two screws
(M4 X 8)

Figure 2-48 Removing the L-Bracket

3. Turn the L-Bracket upside down.
Rotate the L-Bracket 180 degrees so that the upper FACE as shown in Figure 2-48 Removing
the L-Bracket on this page is located at the bottom as shown in Figure 2-49 Securing the
L-Bracket and WM Hook on the next page.
4. Insert tabs on Battery Box into holes on L-Bracket.
Secure the L-Bracket to the Battery Box using two screws.
5. Using two screws (M4x8), secure the WM Hook to the L-Bracket.
6. Using two anchor bolts (locally procured), secure the WM Hook to the wall.

The WM Hook is required for securing both Floor-mount and Wall-mount cases.

Hardware Manual 2-31

SL1100 ISSUE 1.0

Anchor Bolts

WM Hook

Two screws
(M4 X 8)

L-Bracket

Two screws
(M4 X 8)

Figure 2-49 Securing the L-Bracket and WM Hook

7. Install four screws into the L-Bracket (Do not tighten). A space of 2.5 mm (0.098″) to 3.5 mm
(0.138″) for KSU mounting is required. Mount the KSU on the screw heads.

KSU
A
a
B
C
b c Four Screws
D (M4 X 8)
d

Four holes

Figure 2-50 Attaching the KSU

8. Hold open the Sub-Cover of the KSU, and fasten two screws to mount the KSU.

2-32 Installation
ISSUE 1.0 SL1100

Sub-Cover

Two screws

Figure 2-51 KSU Mounting on Battery Box

2.7 IP4WW-Battery Box to KSU Connection

To avoid damage to equipment, do not install the Topaz Battery Box (DX2E-
32i/NX7E Battery Box) to the SL1100 system.

• Make sure the system power is off.

• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.

1. Power off the KSU and disconnect AC cord.

2. Open the Sub-Cover of the KSU.

Push to hold

Open
Sub-Cover

Figure 2-52 Sub-Cover Open and Hold

3. Cut and remove Plastic Knockout from the Sub-Cover to connect Battery cable.

Hardware Manual 2-33

SL1100 ISSUE 1.0

Plastic
Knockout

Sub-Cover

Battery cable

Figure 2-53 Connecting Battery Cable

4. Connect Battery cable from the Battery box to Battery connector on the KSU.

2.8 IP4WW-Battery Box Fuse Replacement

• In the event of a blown fuse correct the fault causing the fuse to blow before
replacing the fuse; otherwise you may cause fire or electrical hazards.
• Be sure to use only the specified fuse (250VT8AL).
• Be sure to install the fuse into the correct location.
• Be careful not to burn yourself on the heated fuse. The blown fuse may be
heated soon after blowing.
• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.

1. Power off the KSU and disconnect AC cord.

2. Loosen two screws and remove the Front Cover.

Two screws
(with stopper)

Front Cover

Figure 2-54 Removing the Front Cover

3. Disconnect the Battery connection cable from the Fuse Unit.

2-34 Installation
ISSUE 1.0 SL1100

Battery Connection Cable

Fuse Unit

Figure 2-55 Disconnecting the Battery Connection Cable

4. Loosen the screw from the Fuse Unit.

Fuse Unit

Screw
Figure 2-56 Loosen the Fuse Unit Screw
5. Slide Fuse Unit out of the Battery box.
6. Replace the fuse (250VT8AL).

Fuse Unit

250VT8AL
Fuse

Fuse Unit guide

Figure 2-57 Replacing the Fuse

7. Using the Fuse Unit guides, slide the Fuse Unit into the Battery Box.

Hardware Manual 2-35

SL1100 ISSUE 1.0

Fuse Unit

Fuse Unit guide

Figure 2-58 Install the Fuse Unit

8. Secure the Fuse Unit by tightening the screw.

Fuse Unit

Screw
Figure 2-59 Securing the Fuse Unit
9. Reconnect the Battery Connection Cable to the Fuse Unit.

Battery Connection Cable

Fuse Unit

Figure 2-60 Connect Battery Connection Cable

10. Align tabs a to f to holes A to F on Battery Box. Slide the Front Cover into position and tighten the
two screws.

2-36 Installation
ISSUE 1.0 SL1100

D E
f
b
B

c
C
a A
e

Front cover

Two screws
(with stopper)
Figure 2-61 Installation of the Front Cover

Hardware Manual 2-37

SL1100 ISSUE 1.0

SECTION 3 INSTALLING THE EXPANSION INTERFACE CARDS

3.1 General

Up to two expansion interface cards can be installed per KSU.

Table 2-9 Expansion Cards

Expansion Interface Card Description Note

IP4WW-080E-B1 8 digital extensions card

IP4WW-008E-B1 8 analog extensions card

IP4WW-4COIDB-B1 4 analog trunk daughter board (Mount on the 084M-B1/080E-B1/008E-B1)

IP4WW-1PRIU-C1 1 PRI (PRI/T1) card

• The 4COIDB-B1 can be installed in following combinations;

Option Unit
Daughter Board
084M-B1 080E-B1 008E-B1
4COIDB-B1 Yes Yes Yes

3.2 Unpacking

Unpack the 080E-B1/008E-B1/4COIDB-B1/1PRIU-C1 and check it against the following list. Inspect for
physical damage.

Table 2-10 Expansion Card Packing List

Items List of Contents QTY Note

IP4WW-080E-B1 080E-B1 PCB (with PKG Spacer) 1

Nylon Spacers 2

Metal Spacers 2

Screws (with circular washer) 2

IP4WW-008E-B1 008E-B1 PCB (with PKG Spacer) 1

Nylon Spacers 2

Metal Spacers 2

Screws (with circular washer) 2

IP4WW-4COIDB-B1 4COIDB-B1 PCB 1

Nylon Spacers 2

4COIDB Label 1

Metal Spacers 1

Screws (with circular washer) 2

IP4WW-1PRIU-C1 1PRIU-C1 PCB (with PKG Spacer) 1

Nylon Spacers 2

Metal Spacers 2

Screws (with circular washer) 2

2-38 Installation
ISSUE 1.0 SL1100

3.3 Mounting the Expansion Interface Card

DO NOT POWER ON until all installation has been completed.

Fit the optional 4COIDB-B1 daughter boards before installing the 084M-B1/080E-B1/008E-B1 PCBs.

3.3.1 Mounting the 080E-B1/008E-B1/1PRIU-C1 PCBs

The procedure for mounting the expansion interface cards is as follows;

• Do Not Power on until all installation have been completed.

• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.

1. Turn off the system power and disconnect the AC cord from KSU.
2. Open and remove the Sub-Cover.

Tab

Sub-Cover

Tab

Sub-Cover

Figure 2-62 Removing the Sub-Cover

3. Loosen two screws and remove the Main-Cover.

Main-Cover
Two screws

Hooks

Figure 2-63 Removing the Main-Cover

4. Insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified
holes. (Both Nylon and Metal spacers are provided with 080E/008E/1PRIU)
If no more Expansion Interface cards are to be mounted on the 1st PCB, fasten two screws to

Hardware Manual 2-39

SL1100 ISSUE 1.0

secure the 1st PCB on the top of the 080E/008E/1PRIU.

Expansion Interface Card J1

Screws
(1st PCB)
Screw position

1st EXP.
PCB

Both sides are

Nylon-Spacers the same.

Metal-Spacers

J21

Figure 2-64 Mounting the 1st Expansion Interface Card

5. In case a 2nd PCB is mounted, insert two Nylon-spacers into the specified holes, and fasten two
Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with
080E/008E/1PRIU)

2-40 Installation
ISSUE 1.0 SL1100

Fasten two screws to secure the 2nd PCB to the top of the 080E/008E/1PRIU.
Screws
Expansion Interface Card J1
(2nd PCB) Screw position
2nd EXP.
PCB
Nylon-Spacers
Both sides are
J2 the same.
Expansion Interface Card
(1st PCB)
Metal-Spacers

Figure 2-65 Mounting the 2nd Expansion Interface Card

6. Following illustration shows an example for installing two expansion PCBs onto the KSU.

2nd PCB

1st PCB

Figure 2-66 Mounting Two Expansion Interface Cards

7. Cut and remove the Plastic Knockouts as required for each Expansion interface card.

Hardware Manual 2-41

SL1100 ISSUE 1.0

EXP.1st PCB
Main-Cover

EXP.2nd PCB

Plastic
Knockouts

Figure 2-67 Plastic Knockouts

8. Replace the Main-Cover and fasten two screws.

Main-Cover
Two screws

Hooks

Figure 2-68 Replacing the Main-Cover

2-42 Installation
ISSUE 1.0 SL1100

3.3.2 Mounting the 4COIDB PCB

1. Cut and remove specified Plastic Knockouts on the 084M-B1/080E-B1/008E-B1 PCB.

Plastic Knockout

084M-B1

Plastic Knockout

080E-B1/008E-B1
Figure 2-69 Plastic Knockouts on 084M-B1/080E-B1/008E-B1
2. Insert two Nylon-spacers into the specified holes. Using supplied screw, fasten Metal Spacer to
4COIDB-B1 PCB.
3. Mount the 4COIDB-B1 PCB onto the 084M-B1/080E-B1/008E-B1 PCB using two Nylon-spacers
and one screw. (Refer to Figure 2-70 Installing the 4COIDB-B1 on this page)
4. Attach the 4COIDB Label to the specified position on the 084M-B1/080E-B1/008E-B1 PCB.

4COIDB-B1 PCB
J1
Screw

Nylon-Spacers
Metal-Spacer
4COIDB Label

J3

084M-B1/080E-B1/008E-B1 PCB Screw

Figure 2-70 Installing the 4COIDB-B1
The 4COIDB-B1 cannot be mounted on the 1PRIU-C1 PCB.

5. Mount the 4COIDB-B1 with 084M-B1/080E-B1/008E-B1 PCB into the KSU.

Hardware Manual 2-43

SL1100 ISSUE 1.0

Screws
084M-B1/080E-B1/008E-B1 PCB
and 4COIDB-B1 PCB J1

Nylon-
Spacers

J21

Metal-Spacers

Figure 2-71 Mounting the 4COIDB-B1 into the KSU

6. Replace the Main-Cover and fasten two screws.

Main-Cover
Two screws

Hooks

Figure 2-72 Replacing the Main-Cover

3.4 Cabling and Setting the Expansion Interface Card

Precautions for Cabling
• Do not wire the cable with an AC cable, computer, etc.
• Do not run the cable near the high frequency generating device.
• Use cable protectors in case the cables run on the floor.
• Aerial distribution wiring is not allowed.
• Trunks must be installed with lightning protectors.

2-44 Installation
ISSUE 1.0 SL1100

• Do not install the DSX Terminal in the SL1100 system, it does not work properly.

3.4.1 Cabling IP4WW-080E-B1

This IP4WW-080E-B1 PCB provides two RJ-61 connections for digital extensions.

Before plugging in the Multiline Telephone, DSS Console, Single line Telephone
or Doorphone, ensure all Main and Expansion KSUs are powered off.

DSX Terminal does not work properly when it connected.

J102 J101

ESI 5-8 ESI 1-4

5 43 6 2 7 1 8

Port 1 Port 2 Port 3 Port 4

T R T R
T: Tip
R: Ring
Modular Cable
(2-wire, Straight)

Exit Help

ABC DEF
Flash Transfer
1 2 3
GHI JKL MNO
Mute DND
4 5 6
PQRS TUV WXYZ
Clear/Back
7 8 9
0 㸡
Speaker Hold

Multiline Telephone DSS Console

Figure 2-73 Connectors of 080E-B1

Hardware Manual 2-45

SL1100 ISSUE 1.0

3.4.1.1 Connectors

The following table shows the pin-outs for the RJ-61 cable connector for Digital extension connections.

Table 2-11 RJ-61 Digital Connector Pin-Outs (J101, J102)

Pin No. ESI 1-4 (J101), ESI 5-8 (J102): 2-Wire Digital Extension
Port Connector (RJ-61)
1 T4 (Tip for port 4)

2 T3 (Tip for port 3)

3 T2 (Tip for port 2)

8 765 4321 4 R1 (Ring for port 1)

5 T1 (Tip for port 1)

6 R2 (Ring for port 2)

7 R3 (Ring for port 3)

8 R4 (Ring for port 4)

3.4.2 Cabling IP4WW-008E-B1

This IP4WW-008E-B1 PCB provides two RJ-61 connections for analog extensions.

Before plugging in the Multiline Telephone, DSS Console, Single line Telephone
or Doorphone, ensure all Main and Expansion KSUs are powered off.

DSX Terminal does not work properly when it connected.

2-46 Installation
ISSUE 1.0 SL1100

J102 J101

SLI 5-8 SLI 1-4

5 43 6 2 7 1 8

Port 1 Port 2 Port 3 Port 4

T R

T : Tip
R : Ring Modular Cable
(2-wire, Straight)

5 6

䂯 䂥

SLT
Figure 2-74 Connectors of 008E-B1

While an Analog Telephone (port) is ringing or MW-lamp is flashing on an

Analog Phone (port), do not disconnect the phone from the port and or connect
another type of the terminal to this port.

3.4.2.1 Connectors

The following table shows the pin-outs for the RJ-61 cable connector for Analog extension connec-
tions.

Table 2-12 RJ-61 Analog Pin-Outs (J101, J102)

Pin No. SLI 1-4 (J101), SLI 5-8 (J102): 2-Wire Analog Extension
port Connector (RJ-61)
1 T4 (Tip for port 4)

2 T3 (Tip for port 3)

3 T2 (Tip for port 2)

8 765 4321 4 R1 (Ring for port 1)

5 T1 (Tip for port 1)

6 R2 (Ring for port 2)

7 R3 (Ring for port 3)

8 R4 (Ring for port 4)

Hardware Manual 2-47

SL1100 ISSUE 1.0

3.4.3 Cabling and Setting IP4WW-4COIDB-B1

This IP4WW-4COIDB-B1 PCB provides two RJ-61 connections for CO lines (J2) and PFT TEL (J3).
J3 J2

PF1 CO1-4

2-Core Cable
(Non polarity)
5 T1
Analog trunk 1
4 R1
3 T2
Analog trunk 2
Single Line T1 5 6 R2
Telephone R1 4 2 T3
Analog trunk 3
7 R3
1 T4
Analog trunk 4
8 R4
Figure 2-75 Connectors of 4COIDB-B1

3.4.3.1 Connectors

The following table shows the pin-outs for the RJ-61 cable connector for CO (J2) and PF (J3) connec-
tions.

Table 2-13 RJ-61 CO/PF Pin-Outs (J2, J3)

Pin No. CO1-4 (J2): CO Port Connector PF1 (J3): PF Tel Port Connector
(RJ-61) (RJ-61)
1 T4 (Tip for port 4) -

2 T3 (Tip for port 3) -

3 T2 (Tip for port 2) -

8 765 4321 4 R1 (Ring for port 1) R1 (Ring for port 1)

5 T1 (Tip for port 1) T1 (Tip for port 1)

6 R2 (Ring for port 2) -

7 R3 (Ring for port 3) -

8 R4 (Ring for port 4) -

2-48 Installation
ISSUE 1.0 SL1100

3.4.4 Cabling and Setting IP4WW-1PRIU-C1

This IP4WW-1PRIU-C1 PCB provides one RJ-45 PRI connection.

J5

PRI 1

PRI/T1 Line
Figure 2-76 Connector of 1PRIU-C1

3.4.4.1 Connector

Following table shows the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus RJ-45 connec-
tions.

Table 2-14 RJ-45 PRI Pin-Outs (S-Bus, T-Bus)

Pin No. RJ-45 Cable Connector- PRI 1 RJ-45 Cable Connector- PRI 1
(J5) S-Bus Connection (J5) T-Bus Connection
1 TA RA

2 TB RB

3 - -
8 765 4321 4 RA TA

5 RB TB

6 - -

7 - -

8 - -

3.4.4.2 Switch Setting

The following figure shows the location of the switches and LEDs on the IP4WW-1PRIU-C1 Card.
1. Set the switches J6 to J9 according to the system, referring the Table 2-15 Switch Setting of
1PRIU-C1 on this page.

Table 2-15 Switch Setting of 1PRIU-C1

Switch No. Switch Position Description

J6, J7 2M Connect PRI/E1 (2.048 Mb/s) line

1.5M (default) Connect PRI/T1 (1.544 Mb/s) line

J8, J9 T (default) T-Bus connection

S S-Bus connection

2. Connect the cables from the NT1 Network Termination cable to the J5 connector on the 1PRIU-C1
Card.

Hardware Manual 2-49

SL1100 ISSUE 1.0

3. Assign whether the unit works as PRI/T1 by PRG10-51-01.

With normal operation, D4 LED flashes green.

IP4WW-1PRIU-C1
J6
1.5M 2M

J7

1.5M 2M

J6
J8/9
J7
S
T

J8 J9

J5
D3 D4
D3 D4 PRI 1
(Red) (Green)

Figure 2-77 Switches and LEDs Location of 1PRIU-C1

3.4.4.3 LED Indication

LED indications for the IP4WW-1PRIU-C1 are listed in following table. Each LED is listed with its asso-
ciated function and LED and operational status.

Table 2-16 LED Indication

LED Indication
Live LED (D4) Busy LED (D3) Operation Status Remarks
(Green) (Red)
On On System Initializing -

Flash (1s) On The assignment of the unit is refused When you exceed the system
capacity.
When the main software version
is not matched.

Flash (1s) Trouble found during self-diagnostics. -

Flash (100ms) On Normal A Channel is busy (use another -

Operation from Ch1 - Chx)

Off All channels are Idle. -

2-50 Installation
ISSUE 1.0 SL1100

LED Indication

Live LED (D4) Busy LED (D3) Operation Status Remarks

(Green) (Red)
Off On Unit Busy A Channel is busy (use another -
from Ch1 - Chx)

Off All channels are Idle. -

Flash 80ms Downloading firmware -

(On/Off) x3/
400ms Off

T1 Alarm Mode
Refer to following figure for LED pattern information. LED indications for the T1 are listed in
Table 2-17 T1 LED Indications on this page.
120 ms
red
LOS
green

red
AIS
green

red
OOF
green

red
RAI
green

1 cycle 3.8 sec (120ms x 32=3840 ms)

Figure 2-78 1PRIU-C1 LED Indication Pattern of Layer 1 on T1 Unit

Table 2-17 T1 LED Indications

Alarm Details of the alarm The LED indication pattern

LOS LOS (Loss of Signal (Red Alarm)) Following an alarm blink (red, green, red, green), a red
No Signal (Analog Interface) LED lighting up.

AIS AIS (Alarm Indication Signal (Blue Following an alarm blink (red, green, red, green), a red
Alarm)) LED flashes on and off slowly twice

OOF OOF (Out of Frame (Red Alarm)) Following an alarm blink (red, green, red, green), a red
LED and a green LED flash on and off 3 times simultane-
ously.

RAI RAI (Remote Alarm Indication (Yellow Following an alarm blink (red, green, red, green), a green
Alarm)) LED flashes on and off twice.

No alarm System does LED control

3.5 Power Failure Transfer (4COIDB-B1 only)

3.5.1 General
In the event of AC power failure, the specified trunk is directly connected to the specified extension
port as below. And SLT must be connected to the specified extension. The multiline telephone (2W)
does not work when the specified trunk is connected to the specified extension port.

J2 (CO1-4): Trunk Port 1 J3 (PF1): Extension Port 1

Refer to Table 2-13 RJ-61 CO/PF Pin-Outs (J2, J3) on page 2-48 for wiring of the power failure tele-
phone.

• The connected extension must be SLT (Single Line Telephone).

Hardware Manual 2-51

SL1100 ISSUE 1.0

SECTION 4 INSTALLING THE OPTIONAL INTERFACE CARDS

4.1 VoIP Card (VOIPDB-C1)

4.1.1 General

The IP4WW-VOIPDB-C1 daughter board is used to convert the RTP (Real Time Transfer Protocol)
packets via the IP Network and PCM highway. The daughter board is installed on the CPU card.

4.1.2 Unpacking

Table 2-18 VOIPDB-C1 Packing List

Items List of Contents QTY

IP4WW-VOIPDB-C1 IP4WW-VOIPDB-C1 1

Ferrite Core (for Ethernet Cable) 1

4.1.3 Installing the VOIPDB-C1 PCB

• Do not remove or install the CPU Card with the power on.
• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
• When the VOIPDB-C1 is installed on the CPU-B1, the NIC card on the CPU
does not function anymore.

1. Turn off the system power and disconnect AC cord.

2. Open and remove the Sub-Cover.

Tab

Sub-Cover

Tab

Sub-Cover

Figure 2-79 Removing the Sub-Cover

3. Loosen two screws and remove the Main-Cover.

2-52 Installation
ISSUE 1.0 SL1100

Main-Cover
Two screws

Hooks

Figure 2-80 Removing the Main-Cover

4. Press tab A and lift the CPU support bracket. Remove the CPU card.

CPU card

CPU support

084M-B1 at 1228M KSU

Figure 2-81 Removing the CPU Card
5. Install the VOIPDB-C1 daughter board to J5 connector on the CPU card.

Nylon-Spacers

VOIPDB-C1 PCB

J5
CPU card
Nylon-Spacers

Figure 2-82 Installing the VOIPDB-C1 PCB

Hardware Manual 2-53

SL1100 ISSUE 1.0

6. Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure
tab A locks into place.

CPU card

CPU support

084M-B1 at 1228M KSU

Figure 2-83 Installing the CPU Card

7. Cut and remove the Plastic Knockout for VoIP connector, then replace the Main-Cover and fasten
two screws.

Main-Cover Two screws

Plastic
Knockout

Hooks

Figure 2-84 Removing the Plastic Knockout and Replacing the Main-Cover
8. Connect the VOIPDB-C1 to an Switching hub using an LAN Cable.

2-54 Installation
ISSUE 1.0 SL1100

The LAN Cable must pass two times (two rounds) through the Ferrite Core as below. (Ferrite Core
is attached with VOIPDB-C1)

30 - 50 mm
VOIPDB-C1 board (CN1) (1.181″ - 1.967″)

LAN Cable
Ferrite Core
VOIP
Pass 2 times

to HUB

< Bottom View >

Figure 2-85 Connecting a LAN Cable
9. Refer to the SL1100 Programming Manual for detailed programming instructions.
The VoIP feature requires system configuration.
For the details of setting and operation, refer to the SL1100 Features & Specifications Manual
(separate issue).

4.1.4 LED Indication

LED indications for the IP4WW-VOIPDB-C1 are listed Table 2-19 VOIPDB LED Indications on this
page. Each LED is listed with its associated function and operational status.

VOIPDB-C1
board

LINK10
LINK100
LINK1000
ACT

< Bottom View >

Figure 2-86 Location of LEDs
Table 2-19 VOIPDB LED Indications

LED Function LED Status Operation status

ACT Link activity or data transmission and On Green LED lights when link up is completed. LED flash
reception. when data is transmitting or receiving.

LINK1000 1000Base-T link speed indicator On Yellow Lights up when 1000Base-T link up.

Hardware Manual 2-55

SL1100 ISSUE 1.0

LED Function LED Status Operation status

LINK100 100Base-TX link speed indicator. On Red Lights up when 100Base-TX link up.

LINK10 10Base-TX link speed indicator. On Red Lights up when 10Base-T link up.

Table 2-20 Operation of VOIPDB LED Indications

LED Operation status

ACT LINK1000 LINK100 LINK10

Off Off Flash Flash Internal Error (Hardware Error)

Off On Flash Flash

On On Flash Flash

On Off Flash Flash State of half duplex transmission (Not support)

Please change HUB etc. to full duplex transmission.

Flash Blinking one by one The firmware is being updated.

4.2 Installing the CF Card (CFVMS/CFVML)

• Do not remove or install the CPU Card with the power on.
• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
• When installing a compact flash card onto the VMDB the system MUST be
powered off. Never install or uninstall the compact flash card while the system
is under power.
1. Turn off the system power and disconnect AC cord.
2. Remove the CPU card and insert the compact flash card into the CF slot (CN2).

CF card
CPU card
CF Slot (CN2)
VMDB

Figure 2-87 Installing the CF Card

3. Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure
tab A locks into place.

2-56 Installation
ISSUE 1.0 SL1100

SECTION 5 INSTALLING THE MULTILINE TELEPHONES AND

OPTIONAL TERMINALS
5.1 Installing the Multiline Telephones
There are three types of Multiline Telephones available in the SL1100 system.
• IP4WW-12TXH-B-TEL
• IP4WW-24TXH-B-TEL
• IP4WW-24TIXH-C-TEL (IP)

5.1.1 Location of Controls

Handset
Alphanumeric Display
Indicator

Exit
Exit Help
Soft key
Help

Programmable
function keys
24T( )XH only

ABC DEF
Flash Transfer
Flash
1 2 3 Transfer
GHI JKL MNO
Mute DND
4 5 6 DND
PQRS TUV WXYZ
Clear/Back
Mute
7 8 9 Clear/Back

0 㧏
Speaker Hold
Cursor control key
Light Sensor

Hold
Speaker
Dial keys
Speaker
Figure 2-88 Multiline Telephone (12TXH/24TXH/24TIXH (IP))
Table 2-21 Multiline Telephone Functions (12TXH/24TXH/24TIXH (IP))

Functions 12TXH 24TXH 24TIXH

Programming Keys 12 24 24
(Busy lamp field: Red-Green) (Busy lamp field: Red-Green) (Busy lamp field: Red-Green)

Display 24-digit x 3 lines with Backlit

Handsfree Full-duplex

Wall-Mount Kit Yes (Built-in) Yes (Optional)

SoftKeys Yes

Backlit Dial Pad Yes

Incoming LED 2 colors (Red/Green)

Hardware Manual 2-57

SL1100 ISSUE 1.0

Functions 12TXH 24TXH 24TIXH

Connected to Digital Extension Port Ethernet Port on the Network

Headset Port Yes

Power Feeding - - AC Adapter (DC27 V,1 A) or

PoE (IEEE802.3af)

5.1.2 Multiline Telephone Legs Adjustment

The Multiline Telephone provides adjustable legs for angling the phone to best suit each user. The leg
can be set for two different heights (Low/High).

5.1.2.1 Low Position Setting

1. Turn telephone over (button side down).
2. Adjust the legs to desired height.

Leg

< Low position >

Figure 2-89 Leg Setting for Low Position

3. Lead the Line and Handset cords through the applicable grooves.

Handset cord

Telephone
line cord
< Bottom view>

Figure 2-90 Cabling of Multiline Telephone

4. Turn telephone over (button side up).

5.1.2.2 High position setting

1. Turn telephone over (button side down).
2. Pull up the Leg Stoppers.

2-58 Installation
ISSUE 1.0 SL1100

Leg Stopper

Leg

Figure 2-91 Setting for High Position

3. Adjust the leg to desired height.

Leg

< High position >

Figure 2-92 Leg Setting for High Position

4. Lead the Line and Handset cords through the applicable grooves.
(Refer to Figure 2-90 Cabling of Multiline Telephone on the previous page)

Hardware Manual 2-59

SL1100 ISSUE 1.0

5.1.3 Wall-Mounting the Multiline Telephone

1. Arrange the cables and put down the leg as shown below.

Leg Handset cord

Telephone
line cord
< Bottom view>

Figure 2-93 Cabling for Wall-Mount

For IP4WW-24TIXH-C only:
When wall-mounting the IP4WW-24TIXH-C, attach the IP4WW-WALL MOUNT UNIT to the bottom panel
as shown.

IP4WW-WALL
MOUNT UNIT
Claws

Claws

IP4WW-24TIXH-C

Figure 2-94 Wall-Mount Unit - 24TIXH-C

2. Remove the switch-hook from the unit. Turn the tab toward the top. Then slide the hook-switch
into position. Refer to Figure 2-95 Hook-Switch Hanger on the next page.

2-60 Installation
ISSUE 1.0 SL1100

Hook-switch hanger Hook-switch hanger

Figure 2-95 Hook-Switch Hanger
3. Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″).

3 - 4 mm 1 - 3 mm
(0.12″ - 0.16″) (0.04″ - 0.12″)

83.5 mm
(3.287″)

7 - 9.5 mm
(0.28″ - 0.37″)

Minimum 10 mm (0.39″)
Figure 2-96 Wall-Mount Screw Guide
4. Mount the telephone on the wall.

Wall-mounting
holes

Wall side

Figure 2-97 Mounting the Multiline Telephone

Hardware Manual 2-61

SL1100 ISSUE 1.0

5.2 Install the IP Multiline Telephone (IP4WW-24TIXH-C1 TEL)

5.2.1 System Connection

The IP Multiline Telephone is connected via HUB.

KSU
IP Multiline Telephone

LAN Cable
Exit Help

(10BASE-T/100BASE-TX)
ABC DEF
Flash Transfer
1 2 3
GHI JKL MNO
Mute DND
4 5 6
PQRS TUV WXYZ
Clear/Back
7 8 9
0 㧏
Speaker Hold

VOIPDB-C1 Ferrite Core Hub

board (CN1) LAN(=) Connector
PC (X)Connector
Commercial Power
AC-[ ]
UNIT

PC Commercial Power
Figure 2-98 IP Multiline Telephone Connection

5.2.2 Installing the IP Multiline Telephone

1. Connect the LAN Network 10Base-T/100Base-TX cable to the LAN(=) connector.
2. If the Power feeding is used by AC-[ ] UNIT, plug the AC-[ ] UNIT cable to the DC input jack on the
IP Multiline Telephone Base.
3. The IP Multiline Telephone has a Switching HUB to connect a PC to the LAN Network. Connect
the 10Base-T/100Base-TX straight cable used for connection to the PC to the PC(X) connector
and to the PC.

PC(X) LAN(=)
PC(X) LAN(=)

< Bottom view>

Figure 2-99 IP Multiline Telephone Connectors

5.2.3 Applying Power to the IP Multiline Telephone

IP Multiline Telephone (IP4WW-24TIXH-C1) supports two different power sources for the Telephone.
• AC-2R UNIT/AC-L UNIT

2-62 Installation
ISSUE 1.0 SL1100

Plug the Optional AC-[ ] AC adapter input jack in the telephone base unit, and plug the 2-prong wall
plug of the AC adapter in AC outlet.
• PoE(IEEE802.3af)
PoE (Power Over Ethernet) is a LAN technology that allows standard 10Base-T/100Base-TX data
cables to pass electrical current from a power source to a requesting end device.

5.3 Installing the DSS Console

The 60D DSS-B Console can be installed on any digital extension port of each 084M-B1/080E-B1 card
directly. The pair extension for the DSS Console is assigned using system programming.
For the settings, refer to the SL1100 Features & Specifications Manual.

5.3.1 DSS Console Leg Adjustment

The DSS Console provides the leg for angling the console to best suit each user. The leg can be set
for two different heights (Low/High).

5.3.1.1 Low Position Setting

1. Turn DSS Console over (button side down).
2. Adjust the legs to desired height.

Leg

< Low position >

Figure 2-100 Low Position Setting
3. Lead the Line cord through the applicable grooves.

Figure 2-101 Cabling of DSS

5.3.1.2 High position setting

1. Turn DSS Console over (button side down).
2. Pull up the Leg Stoppers.

Hardware Manual 2-63

SL1100 ISSUE 1.0

Leg Stopper

Figure 2-102 Leg Stopper of DSS Console

3. Adjust the leg to desired height.

Leg

< High position >

Figure 2-103 High Position Setting

4. Lead the Line cord through the applicable grooves.
(Refer to Figure 2-101 Cabling of DSS on the previous page)

5.3.2 Wall-Mounting the DSS Console

1. Lift the leg and lead the cable through the applicable grooves. Refer to Figure 2-104 Cabling for
Wall-Mount on the next page. Lower leg to stowed position.

2-64 Installation
ISSUE 1.0 SL1100

Leg

< Bottom view>

Figure 2-104 Cabling for Wall-Mount

2. Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″).

3 - 4 mm 1 - 3 mm
(0.12″ - 0.16″) (0.04″ - 0.12″)

83.5 mm
(3.287″)

7 - 9.5 mm
(0.28″ - 0.37″)

Minimum 10 mm (0.39″)
Figure 2-105 Wall-Mount Screw Guide
3. Mount the DSS Console to the wall.

Wall-mounting
holes

Wall side

Figure 2-106 Mounting the DSS

5.4 Installing the Headset

The Multiline Telephone user can utilize a customer-provided headset in place of the handset. Like
using Handsfree, using the headset frees up the user's hands for other work. However, Headset
Operation provides privacy not available from Handsfree.

Hardware Manual 2-65

SL1100 ISSUE 1.0

1. Connect the Headset cord into the Headset socket.

Headset socket

< Bottom view>

Figure 2-107 Headset Socket (2-wire Multiline Telephone)

Headset socket

PC(X) LAN(=)
LAN(=)

< Bottom view>

Figure 2-108 Headset Socket (IP Multiline Telephone)
<Recommended Headset>
• HW251N-A10-NE
This Item is made by Plantronics, inc.

For the details of setting and operation, refer to the SL1100 Feature & Specifications Manual. (separate issue)
The headset configuration is assigned using system programming.

5.5 Installing the Doorphone Box

5.5.1 Wall-Mounting the Doorphone

1. Remove the screw on the front of the Doorphone Box.
2. Remove the Wall-Mount bracket from the Doorphone Box.
3. Connect the cable to the screw terminals on the Doorphone box. (No polarity sensitive)

2-66 Installation
ISSUE 1.0 SL1100

Wall-mount
bracket Upper housing

Screw
terminals
Screw

Connect cable
Figure 2-109 Doorphone Box and Bracket
4. Mount the Wall-Mount bracket on the wall using supplied screws.
5. Replace the Upper housing and tighten the screw.

Hole
Wall-mount
bracket
Attached screws
Upper housing

Hook

Screw
Figure 2-110 Doorphone

Hardware Manual 2-67

SL1100 ISSUE 1.0

5.5.2 Connecting the Doorphone

J421
J103 J431 J411
J102 J101 J7

RY1/2
SLI 9-12
/DPH 1-2

5 43 6 2 7 1 8

Port 1 Port 2 Port 3 Port 4

T R
T : Tip
R : Ring
Modular Cable
(2-wire, Straight)

Doorphone
Figure 2-111 Connecting the Doorphone
The Doorphone configuration is assigned using system programming.

The 3rd party Doorphone Boxes cannot be connected to the port.

5.5.3 Doorphone Interface Specifications

Table 2-22 Doorphone Interface Specifications

Item Specification
Output Impedance 600 Ω

Output Level Nominal 250 mV (-10 dBm)

Maximum Output 400 mV RMS

2-68 Installation
ISSUE 1.0 SL1100

5.6 Installing the Door Unlock Devices

A maximum of two door unlock devices can be connected to each KSU.

J7 (RJ61)

8 765 4321
RY1/2

Door unlock control devices

Figure 2-112 Connecting the Door Unlock Device

The following table shows the pin-outs for the RJ-61 cable connector.

Table 2-23 RJ-61 General Purpose/Door Unlock Relay Control Connector (J7)

Pin No. Connection

1 -

2 -

3 Relay 2

4 Relay 1

5 Relay 1
8 765 4321
RY1/2 (J7) 6 Relay 2

7 -

8 -

Table 2-24 General Purpose/Door Unlock Relay Specifications

Item Specification
Rated Voltage DC 48 V Maximum

Rated Current DC 320 mA Maximum

Contact Normally Open

Hardware Manual 2-69

SL1100 ISSUE 1.0

5.7 Installing the External Paging Speaker/External MOH/BGM Sources

5.7.1 Connecting the Audio Equipment

• The audio jack labeled PAGE, MOH, BGM can be used for audio port (External paging, External MOH,
BGM)
• Audio port configuration is assigned using system programming.

Audio IN/OUT Jack PAGE : Audio in/out

(External paging)
MOH : Audio in
BGM MOH PAGE (External MOH)
BGM : Audio in
(BGM)

PAGE MOH, BGM

Paging system Audio resource

Figure 2-113 Connecting Audio Equipment

5.7.2 External Paging Output Specifications

Table 2-25 External Paging Output Specifications

Item Specification
Output Impedance 600 Ω @ 1kHz

Output Level Nominal 250 mV (-10 dBm)

Maximum Output 400 mV RMS

2-70 Installation
ISSUE 1.0 SL1100

5.7.3 BGM/External MOH Source Input Specifications

Table 2-26 BGM/External MOH Source Input Specifications

Item Specification
Input Impedance 600 Ω @ 1 kHz

Input Level Nominal 250 mV (-10 dBm)

Maximum Input 1 V RMS

5.8 SMDR (Station Message Detail Recording)

5.8.1 General

SMDR (Station Message Detail Recording) provides a record of the system's outside calls. Typically,
the record outputs to a customer-provided SMDR device such as PC via LAN port (J3) on the CPU
card.

LAN connector
J3 (RJ45)

8 765 4321

PC

Hub

Figure 2-114 Connecting a PC for SMDR

1. Connect the straight type Ethernet cable (CAT5) between the system and In-house LAN.

The SMDR feature is assigned using system programming.

Hardware Manual 2-71

SL1100 ISSUE 1.0

SECTION 6 INSTALLING WIRELESS DECT TELEPHONES

6.1 Installing the DTL-8R-1 Cordless DECT Telephone
DTL-8R-1 is a cordless telephone that is adapted for NEC SL1100 System. It is designed for use in the
office environment.

Figure 2-115 Cordless DECT Telephone (DTL-8R-1)

• A Handset and wired phone cannot be used at the same time.
• The Handset and Base Station must have the original ID that is written on
each unit at the factory.

SL1100 System

Figure 2-116 System Overview

6.1.1 Selecting a Location

Select a location for the DTL-8R-1 Cordless DECT to avoid excessive heat or humidity. The base unit
of the DTL-8R-1 Cordless DECT can be placed on a desk or tabletop near a standard 120 V AC outlet

2-72 Installation
ISSUE 1.0 SL1100

and telephone line jack. The base unit can also be mounted on a standard wall plate using the wall
mount adapter. Keep the base unit and handset away from sources of electrical noise (motors, fluores-
cent lighting, computers, PC monitor).

6.1.2 Installation Precautions

To ensure optimum performance follow these guidelines.
• Base units must be placed at least 20 feet apart.
• Always place the base unit on top of a desk or on higher shelves. Avoid locations surrounded by
metal surfaces.
• Place the base away from any electrical component such as a PC, monitor and other telephone.

6.1.3 Connecting the Telephone Cords

When connecting the telephone cords, observe the following precautions.

• Never install telephone wiring during a lightning storm.

• Never touch bare telephone wires or terminals unless the telephone line is
disconnected at the network interface.
• Use caution when installing or modifying telephone lines.

To connect the telephone cords:

1. Connect the cord from the telephone jack to the Line In on the DTL-8R-1 Cordless DECT.

Figure 2-117 Connecting Telephone Cords to the Telephone Jack

2. Connect a SL1100 digital multiline terminal to the DTL-8R-1 Cordless DECT.

Line "OUT"

To SL1100 Multiline Terminals

Figure 2-118 Connecting the DTL-8R-1 Cordless DECT to the Multiline Terminal

Hardware Manual 2-73

SL1100 ISSUE 1.0

6.1.4 Applying Power to the Charging Unit

The unique design of the telephone allows the user to place the handset in the charging unit with or
without the belt clip attached. The charging unit can charge a second battery with or without the
handset being charged. The battery packs can be recharged automatically either in or out of the
handset.

Figure 2-119 Applying Power to the Charging Unit

Use only the supplied AC adapter for the charging unit.

The AC adapter furnished with this telephone usually has a polarized line plug with one blade wider
than the other. This plug fits in the power outlet only one way. If you cannot insert the plug fully in the
outlet, try reversing the plug.

Refer to Figure 2-120 Polarized Plug on this page.

If you cannot plug the AC adapter in the outlet, you may need to replace it.

Route the power cord where it can not create a trip hazard, or where it could
become chafed and create a fire or other electrical hazards.

Figure 2-120 Polarized Plug

6.1.5 Mounting the Base to a Standard Wall Plate

The base unit can be mounted on a standard wall plate. To attach the wall mount stand to the base
unit:
1. Slide the wall mount stand in the notches at the top of the base unit.

2-74 Installation
ISSUE 1.0 SL1100

Rotate the wall mount stand down and snap it into place.

Figure 2-121 Attaching the Wall Mount Stand to the Base Unit
2. Plug the AC adapter into the base unit.
3. Place the AC adapter cord inside the molded channel of the wall mount stand.

Figure 2-122 Placing the AC Adapter Cord Inside the Wall Mount Stand
4. Plug one end of the short telephone cord (locally supplied) in the LINE jack on the base unit. Plug
one end of the SL1100 digital multiline terminal into the PHONE jack. Place the telephone cords
inside the molded channels on the bottom of the wall mount stand.
5. Plug the other end of the short telephone cord into the modular wall jack in the center of the wall
plate.
6. Place the base unit on the posts of the wall plate and push down until it is firmly seated.

Hardware Manual 2-75

SL1100 ISSUE 1.0

Figure 2-123 Placing the Base Unit on the Posts of the Wall Plate
Because of variation in wall plates, this method is not recommended.

7. Plug the AC adapter into a standard 120 Vac wall outlet.

Do not use an outlet controlled by a wall switch.

Figure 2-124 Plugging the AC Adapter into the AC Wall Outlet

6.1.6 Mounting the Base Directly to the Wall

If a standard wall plate is not available, mount the telephone directly on the wall. Before mounting the
telephone, consider the following:
• Select a location away from electrical cables, pipes, or other items behind the mounting location that
could cause a hazard when inserting screws into the wall.
• Make sure the wall material can support the weight of the base unit.
• Use #10 screws with anchoring devices suitable for the wall material where the base unit will be
placed.

To mount the telephone:

1. Insert two mounting screws 3-15/16 inches apart. Allow about 3/16 of an inch between the wall
and screw heads for mounting the telephone.

2-76 Installation
ISSUE 1.0 SL1100

Figure 2-125 Inserting Screws into the Wall for Wall Mounting the Telephone
2. Plug in and secure the AC adapter.
3. Plug the AC adapter into the base unit.
4. Plug one end of the short telephone cord into the LINE jack on the base unit. Then plug one end
of a SL1100 multiline terminal into the PHONE jack. Place the telephone cords inside the molded
channels on the bottom of the wall mount stand.

Figure 2-126 Placing the Telephone Cords Inside the Wall Mount Stand
5. Place the base unit on the posts of the wall screws and push down until it is firmly seated.

Figure 2-127 Attaching the Wall Mount Unit to the Wall

Hardware Manual 2-77

SL1100 ISSUE 1.0

6. Plug the other end of the short telephone cord into a telephone wall jack.
7. Plug the AC adapter into a standard 120 Vac wall outlet. Refer to Figure 2-124 Plugging the AC
Adapter into the AC Wall Outlet on page 2-76.

Do not use an outlet controlled by a wall switch.

6.1.7 Wall Mounting the Charging Unit

The charging unit can be wall mounted as well. Before mounting the charging unit, consider the
following:
• Select a location away from electrical cables, pipes, or other items behind the mounting location that
could cause a hazard when inserting screws into the wall.
• Make sure the wall material can support the weight of the charging unit.
• Use #10 screws with anchoring devices suitable for the wall material where the charging unit will be
placed.

To mount the charging unit:

1. Insert two mounting screws as shown below. Allow about 3/16 of an inch between the wall and
screw heads for mounting the telephone.

Figure 2-128 Inserting Screws for Wall Mounting

2. Plug the AC adapter in the charging unit. Wrap the AC adapter cord around the strain relief.

Figure 2-129 Wrapping the AC Adapter Cord Around the Strain Relief
3. Place the charging unit on the posts of the wall screws and push down until it is firmly seated.

2-78 Installation
ISSUE 1.0 SL1100

Figure 2-130 Placing the Charging Unit on the Wall

4. Plug the AC adapter into a standard 120 Vac wall outlet. Refer to Figure 2-130 Placing the
Charging Unit on the Wall on this page.

6.1.8 Attaching and Removing the Belt Clip

A belt clip can be used to attach the handset to a belt or pocket for convenient portability.
1. Slide the clip into the tab slots. Press firmly until it snaps into place. The belt clip fits snugly onto
the handset.

Figure 2-131 Attaching the Belt Clip to the Handset

2. To remove the clip, press the retaining clip in toward the belt clip blade and slide the clip up at the
same time.

Hardware Manual 2-79

SL1100 ISSUE 1.0

Figure 2-132 Removing the Belt Clip

6.1.9 Installing the Handset Battery Pack

Before installing batteries, refer to Dterm® Cordless DECT Owner’s Manual Specifications and Battery
Safety. It is important to follow safety regulations when handling batteries.
1. Remove the battery cover by pressing the latch and sliding the cover down and off of the handset.

Figure 2-133 Removing the Battery Cover

2. Slide the battery pack down into the handset.

It may be necessary to remove the old battery at this time.

Figure 2-134 Replacing the Battery Pack

3. Replace the cover and slide it up until it latches onto the handset.

2-80 Installation
ISSUE 1.0 SL1100

Figure 2-135 Replacing the Battery Cover

6.1.10 Charging Batteries

The rechargeable battery pack must be fully charged before using the DTL-8R-1 Cordless DECT for
the first time.

Charge the battery pack without interruption for five to eight hours.

6.1.11 Charging Spare Battery Packs

The DTL-8R-1 Cordless DECT is equipped with a battery charger for charging the spare battery pack.

Hardware Manual 2-81

SL1100 ISSUE 1.0

6.2 Installing the DTL-RPT-1 Cordless DECT Telephone REPEATER

The UDR100 repeater lets you extend the coverage area of your cordless DECT telephone system in
all directions.

Figure 2-136 Cordless DECT Telephone Repeater DTL-RPT-1

If the repeaters are installed so their coverage area overlaps the coverage area of the base, the base
can hand-off calls to the repeaters as the user moves from one coverage area to another. When
connected to the repeater, the mobile handset operates the exact same way as it does when
connected to the base, and the hand-off from the base to the repeater can be completely invisible to

2-82 Installation
ISSUE 1.0 SL1100

the end user, even during an active call.

Figure 2-137 Single Repeater Attached to Base

Each base supports up to six repeaters, so you can extend coverage in all directions, including through
floors and ceilings:

Figure 2-138 Six Repeaters Attached to Base

Hardware Manual 2-83

SL1100 ISSUE 1.0

In addition, the UDR100 supports a sequential or "daisy-chain" layout to extend coverage in a single
direction. Up to three repeaters can be installed in sequence:

Figure 2-139 Daisy-Chain Layout

For detailed information on daisy-chain layout and configuration, contact your installer or refer to the
UDR100 Administrator's Guide.

6.2.1 Setting Up Your Repeater

Before installing the repeater, you must activate the repeater mode on your base and then register the
repeater to the base and any handsets. Before you start the registration process, be sure you have:
• A working base
• A working handset registered to that base
• Any repeaters you want to register to this base (you must complete the registration process sepa-
rately for each repeater)
• At least one of the AC adapters supplied with the repeaters

Use ONLY the power adapter that came with your repeater. A different power adapter may cause an electrical
hazard or damage the repeater.

6.2.1.1 Changing the Telephone System PIN

Before you start the registration process, you must reset the system PIN of your telephone to 0000
(consult the manual that came with your base for more information). After you reset the PIN, make
sure to register the handset you used back to the base station.

6.2.1.2 Automatic Registration

The repeater seeks out the base with strongest DECT/GAP signal and automatically registers to that
base.
1. Make sure the repeater is powered off (i.e., the AC power adapter is not connected).
2. Set the base in registration mode. (Consult the owner's manual that came with your base station
for more information.
3. Use the AC adapter to connect the repeater to a standard 120 V AC outlet. (Do not use a power
outlet controlled by a wall switch.) The LED on the repeater flashes briefly, then remains on and
steady.

If the LED continues to flash, register the repeater again.

The repeater is now registered to this base and is ready to use.

You can safely disconnect the power and move the repeater to the selected location; the repeater
stays registered to the base.

6.2.1.3 Manual Registration

If you are registering more than one repeater to the same base, you must use the manual registration
procedure.
1. Connect the repeater to power for 1 ~ 5 seconds and then disconnect it.

2-84 Installation
ISSUE 1.0 SL1100

2. Reconnect the power to the repeater. The LED on the repeater flashes slowly, indicating the
repeater is in registration mode.

The repeater stays in registration mode for five minutes. If you cannot complete the registration in five
minutes, repeat the procedure starting with step 1.
3. Set the base in registration mode. (Consult the owner's manual that came with your base station
for more information.)
4. The LED on the front of the repeater flashes quickly, with no interruptions.

If the LED has brief interruptions in the flash, you need to reset your telephone system PIN to 0000. (Refer to
Changing the Telephone System PIN on the previous page.)
5. Press the handset TALK? key to go off-hook. The LED stops flashing.
6. Use the number pad on the handset to assign a repeater number. Press a number between 2 and
7. Each repeater number can be used only once per base. (These numbers are independent of
any handset extension number.)
7. When the repeater accepts the assignment, the LED flashes a corresponding number of times.
8. Press the STAR? key to confirm the registration, and then the END? key. The LED goes off for two
seconds, flashes for a brief moment, and then remains on steady.

The repeater is now registered to this base station. You can repeat the procedure with each repeater
that you want to register to this base, or you can disconnect the power and move the repeater to the
selected location.

The repeater remains registered even if you disconnect the AC adapter or there is a power failure. If you want
to clear the registration (for example, so you can register to a different base), you must reset the repeater.

6.2.1.4 Registration for a Daisy-Chain Layout

Registering the repeaters to operate in a daisy-chain or sequential layout requires network adminis-
trator access and configuration software. Contact your installer or refer to the DTL-RPT-1
Administrator's Guide (provided with the configuration software) for more information.

6.2.1.5 Registering to a Different Base

After the repeater is registered, you must reset it before you can change the registration to a different
base. If you want to reset the repeater and clear its registration, follow the steps below:
1. Disconnect the power.
2. Connect the power for one to five seconds, and disconnect it again.
3. Connect the power for 25 ~ 35 seconds.
4. Disconnect the power, and perform the registration procedure with the new base.

6.2.2 Installing the Repeater

6.2.2.1 Finding the Right Location

To get the best operating conditions for the repeater, it is important to place it correctly. Here are a few
tips for placing repeaters:
• Place the repeater as high as possible, but at least six feet above the floor.
• Make sure you have good reception from the base.
• Make sure the location is close to a standard 120 V AC power outlet. Never install electrical cords
across a traffic area: they can create a trip hazard or become damaged and create a fire or electrical
hazard.
• Allow at least 30 feet between repeaters (if you are installing repeaters across multiple floors,
remember to allow 30 feet vertically, also).
• Avoid sources of electrical interference, such as hi-fi systems, office equipment or microwave ovens.
• Avoid heat sources and direct sunlight.
• Avoid things that can interfere with radio signals, such as metal doors, thick walls, niches and
cupboards.

Hardware Manual 2-85

SL1100 ISSUE 1.0

6.2.2.2 Map the Base Coverage Area

To find the best location for the repeater, you need to determine the base coverage area. Stand near
the base and make a call. Walk away from the base with the handset, and make a note where the
signal becomes weaker. The optimum location for the repeater is as far from the base as possible
while still maintaining a good signal, or just inside the location where the signal became weaker.

Base Coverage Area

6.2.2.3 Test the Location

To test the location, plug the AC adapter into the repeater, then hold the repeater in the place where
you plan to mount it. The LED should remain on and steady, indicating that the repeater has a good
signal from the base.

If the LED flashes, the repeater is not getting a good signal. The repeater may be too far away from
the base, there may be interference from electronic devices, or the signal might be blocked by thick
walls or metal objects. Try moving the repeater to another location.

6.2.2.4 Installing the Repeater

Be sure the wall material can hold the weight of the repeater. Never install a
repeater in damaged or decaying wall material.
1. Hold the repeater in its final location, and mark the center of the top edge.
2. From the edge mark, measure down approximately 1-1/2 inches, and mark the screw location.
3. At the screw location, use a 3/16ths drill bit to make a pilot hole approximately one inch deep.
4. Place the wall anchor into the pilot hole and tap it gently with a hammer until the anchor is flush
with the wall.
5. Insert the mounting screw into the anchor, leaving approximately 1/4 inch space between the
screw head and the wall.
6. Put the repeater over the screw head and slide it down into place.
7. Connect the repeater to the 120V AC power outlet.

2-86 Installation
ISSUE 1.0 SL1100

6.2.2.5 Multiple Repeater Systems

You can register up to six repeaters to one base as long as the repeaters are a minimum of 30 feet
apart. Remember that the signal can cross through walls and floors.

Incorrect Installation

Figure 2-141 Incorrect Installation on this page illustrates repeaters that are incorrectly installed.

Figure 2-141 Incorrect Installation

Correct Installation

Figure 2-142 Base Coverage Area on this page illustrates repeaters that are correctly installed.

Figure 2-142 Base Coverage Area

Daisy-Chain Installation

Hardware Manual 2-87

SL1100 ISSUE 1.0

You can combine normal and daisy-chain connections to create a wide variety of coverage configura-
tions, as long as you have no more than six repeaters per base unit.

Figure 2-143 Daisy-Chain Layout

6.2.3 Troubleshooting Chart

To review common problems and possible solutions, refer to the Cordless DECT Repeater Guide
DTL-RPT-1.

6.2.4 Turning on the Verification Tone

To activate the verification tone to aid in troubleshooting installation problems, refer to the Cordless
DECT Repeater Guide DTL-RPT-1.

6.2.5 Maintenance

For user maintenance of the repeater, refer to the Cordless DECT Repeater Guide DTL-RPT-1.

6.3 Installing the ML440 and AP20 Wireless DECT Telephone

This section outlines the steps for connecting and mounting the base station, charging the battery, and
powering on the handset.

The following topics are included in this section:

• Connecting the Base Station on the next page
• Wall Mounting the Base Station on page 2-90
• Handset and Charger on page 2-92

2-88 Installation
ISSUE 1.0 SL1100

6.3.1 Connecting the Base Station

Figure 2-144 Base Station Front and Back View on this page provides a front and rear view of the
base station.
Front View Rear View

Figure 2-144 Base Station Front and Back View

If your network connection does not provide Power Over Ethernet, you will need to order a base station AC
adapter and a standard Ethernet-to-PoE adapter. Contact Customer Service.

Follow the steps below to connect the base station.

1. Connect a standard Ethernet cable (Cat 5 or higher) to the Ethernet/PoE jack on the rear of the
base station.
2. Route the cable through the channel as shown in Figure 2-145 Connecting the Base Station on
the next page.

Hardware Manual 2-89

SL1100 ISSUE 1.0

Figure 2-145 Connecting the Base Station

3. Connect the other end of the cable to your TCP/IP network.
When the base station powers on, the STATUS LED on the front briefly lights orange and then
turns off while it initializes and connects to the network. After the base station successfully initial-
izes and connects to the network, the LED lights green and remains steady on.
Table 2-27 Base Station LEDs States and Meanings on this page provides a list of base station
LEDs and their meanings.

Table 2-27 Base Station LEDs States and Meanings

Color State Meaning

Green Flickering Stage in base flash memory rewrite at the end of the base firmware update.

Green Steady on All operations normal.

N/A Off No power in unit

OR
initializing and connecting to the network.

Orange Briefly on Powering on.

Orange Flickering Stage in base flash memory rewrite at the end of the base firmware update.

Red Blinking Factory reset warning. A factory reset has been initiated or is in progress.

Red Blinking No Ethernet connection available

OR
handset registration failed.

Red Flickering Stage in base flash memory rewrite at the end of the base firmware update.

Red Steady on Critical error. Contact technical support.

6.3.2 Wall Mounting the Base Station

Follow the steps below to mount the base station to a wall.

Be sure the wall material can hold the weight of the base.
1. Hold the base in its final location and mark the screw location based on the measurements shown
in Figure 2-146 Base Mounting Dimensions on the next page.

2-90 Installation
ISSUE 1.0 SL1100

Figure 2-146 Base Mounting Dimensions

2. Insert the appropriate anchors for the wall material.
3. Insert the mounting screws into the anchors, leaving about 1/4 inch of space between the screw
head and the wall.
4. Connect the Ethernet cable and route the cord as shown in Figure 2-146 Base Mounting
Dimensions on this page.
5. Place the base over the screw heads and slide it down into place.

Hardware Manual 2-91

SL1100 ISSUE 1.0

6.3.3 Handset and Charger

Figure 2-147 Handset Front View on this page provides a front view of the handset and
Figure 2-148 Charger Top View on the next page provides a top view of the charger.

Figure 2-147 Handset Front View

2-92 Installation
ISSUE 1.0 SL1100

Figure 2-148 Charger Top View

6.3.3.1 Charging the Battery

Follow the steps below to charge the battery.

1. Install the handset battery as shown below in Figure 2-149 Installing the Handset Battery on this
page.

Figure 2-149 Installing the Handset Battery

2. Use the charger AC adapter to connect the charger's AC jack to a standard 120 V AC power
outlet.
3. Place the handset in the charger with the display facing forward. The HANDSET STATUS LED
should turn on; if it doesn't, reseat the handset or try plugging the AC adapter into a different
outlet.

Hardware Manual 2-93

SL1100 ISSUE 1.0

4. Place the spare battery (if available) in the back section of the charger; the BATTERY STATUS
LED should turn on. (Pull the battery latch back slightly to fit the battery in the slot.) See
Figure 2-150 Inserting Handset into the Charger on the previous page.

Figure 2-150 Inserting Handset into the Charger

Charge each battery completely (about 10 hours) before use.

6.3.3.2 Powering on the Handset

To power up the handset, press and hold End until the display flashes once (about 3 seconds). The
handset searches for the base station or multi-cell chain it is registered to and connects to the unit with
the strongest signal.

2-94 Installation
System Start Up
SECTION 1 SYSTEM START UP
3
1.1 Before Starting Up the System

System Start Up
Before starting up the system, make sure:
• KSU(s) are installed correctly.
• All extensions are cabled correctly.
• All earth ground and PSTN Trunks are cabled correctly.
• All PCBs are configured, equipped, and secured correctly.
• AC power cord is cabled correctly.
• At least one display type Multiline Telephone is connected to the system. (for Programming)
• Pull out the Lithium battery protection sheet, before starting up the system.

Lithium battery protection sheet

Figure 3-1 Lithium Battery Protection Sheet

• If Expansion KSU(s) are installed, turn the power on/off in the order of Expansion 2 KSU, Expansion
1 KSU and then Main KSU.

1.2 Starting Up the System

There are two methods for startup (COLD Start and HOT Start).

Table 3-1 Start Up Method

Start Up Method Description Purpose

COLD Start The factory setting data is loaded. • First time start up
• System Initialization

HOT Start The customer setting data is loaded. • System Reboot

Hardware Manual 3-1

SL1100 ISSUE 1.0

1.2.1 Perform a Cold Start

This section describes the process for starting the system for the first time or starting a system that
requires the customer data be deleted.

System software is loaded from flash memory, and the customer data is deleted
from RAM memory.

If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
To perform a Cold Start;
1. Set the power switch to off position.

Figure 3-2 Power Switch Location

2. Open the Sub-Cover on the Main KSU and identify the LOAD button (S1) location on the CPU
card.

Tab

Sub-Cover CPU card

S1
Tab
LOAD

< Front view >

Figure 3-3 Load Button (S1) Location

3. Once the system has powered off, push in and hold the LOAD button (S1).

If Expansion KSU(s) are installed, the Power Switch must be ON at Expansion

KSU(s).
4. Turn the power switch ON at the Main KSU.

3-2 System Start Up

ISSUE 1.0 SL1100

5. Continue holding the LOAD button (S1) for approximately three seconds or until Status LED (D5)
starts flashing red.

RUN LED

LED (D5)

< Front view >

Figure 3-4 Status LED (D5) and RUN LED Location

6. Release the LOAD button.
7. When the system has completed reloading the software (about two minutes), the RUN LED is
flashing blue on the CPU card and the connected Multiline Telephone's display will show the Time
& Date and Extension Number.

11-10 WED 1:49PM

200
Menu Dir VM:00 CL:00

Figure 3-5 Display Indication (Idle)

1.2.2 Perform a Hot Start

This section describes how to load system software from flash memory, and the customer data from
RAM memory.

System software is loaded from flash memory, and the customer data is loaded
from RAM memory.

If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
To perform a Hot Start;
1. Turn the system power off.
2. After it has powered off, turn the power switch back to ON. Wait approximately two minutes.
3. When the system has completed reloading the software, the RUN LED is flashing blue on the
CPU card, and the connected Multiline Telephone's display will show the Time & Date and Exten-
sion Number as Figure 3-5 Display Indication (Idle) on this page.

Hardware Manual 3-3

SL1100 ISSUE 1.0

SECTION 2 PROGRAMMING MODE

2.1 Entering the Programming Mode

The installer/system administrator can enter to the system programming mode from the Display Type
Multiline Telephone. (A maximum of two users can enter mode at the same time)

In a newly installed system, use extension port 1.

1. Press Speaker key. (Do not lift the handset)

2. Dial # # .
* *
11-10 WED 1:49PM
200 Password
Menu Dir VM:00 CL:00
Figure 3-6 Entering Programming Mode Display 1
3. Dial the system password, then press Hold key to enter the Program Mode.

Password@@@@@@@@ Program Mode

Base Service OP1 OP2
Figure 3-7 Entering Programming Mode Display 2
For the details of programming, refer to the SL1100 Programming Manual. (separate issue)

2.2 Exiting the Programming Mode

1. Press Mute key several times to return to the "Program Mode" Screen.

10-01- Sys Config

Time&Date Setup |01 Program Mode
back Select Base Service OP1 OP2
Figure 3-8 Exiting the Programming Mode Display 1
2. Press Speaker key to exit.

11-10 WED 1:49PM

Program Mode 200
Base Service OP1 OP2 Menu Dir VM:00 CL:00
Figure 3-9 Exiting Programming Mode Display 2
The system automatically saves the customer data to the memory which is backed up by lithium battery.

2.3 Saving (Backup) the Customer Data

When the installer/system administrator exits from the programming mode, the system will automati-
cally save the customer data to the on-board memory which is backed up by lithium battery.
Additionally, the customer data can be saved to a CF Card for backup purpose. The BLANK CF card
is inserted to the CF slot on the VMDB.
1. Turn the system power off, insert the blank CF card (32 MB or larger) to the CF slot on VMDB.

3-4 System Start Up

ISSUE 1.0 SL1100

CPU card

CF Slot (CN2)
CF card
VMDB

Figure 3-10 Inserting the CF card

2. Turn the power on, enter the Program Mode then PRG90-03.

90-03-01
Program Mode Data Save YES:1 1
Base Service OP1 OP2
Figure 3-11 PRG90-03 Display
3. Dial 1 and press Hold key.
4. When the data backup to the CF card is completed, the display will be changed to the next PRG.

90-04- M’tenance
Saving System Data Load Data |01
back Select

Figure 3-12 PRG90-04 Display

5. Remove the CF Card and exit from the Programming Mode.

The saved data on CF Card cannot be edited by the PC.

2.4 Loading the Customer Data

The backed up customer data can be loaded to the system by CF Card.

1. Turn the power off, insert the Customer Data CF card into the CF Slot on VMDB.

Hardware Manual 3-5

SL1100 ISSUE 1.0

CPU card

CF Slot (CN2)
CF card
VMDB

Figure 3-13 Inserting the CF card

2. Turn the power on, enter the Program Mode then PRG90-04.

90-04-01
Program Mode Data Load YES:1 1
Base Service OP1 OP2
Figure 3-14 PRG90-04 Display
3. Dial 1 and press Hold key.
4. When the data backup to the CF card is completed, the display changes to the next PRG.

90-05- M’tenance
Loading System Data Slot Control |01
back Select

Figure 3-15 Next PRG Display

5. Remove the CF card and exit from the Program Mode.

3-6 System Start Up

ISSUE 1.0 SL1100

SECTION 3 SYSTEM SHUT DOWN

3.1 Powering Off the System

1. Turn the all KSU(s) power off using the power switch.

Figure 3-16 Power Switch Location

• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
• DO NOT power off by disconnecting the AC (or DC for battery backup) power.
Always use the Power Switch on the Main/Expansion KSU.
• All calls in progress will be cut off when the system is powered off, and if the
Power Failure is set, the applicable extension will become operational.
• All user's setting (such as Call Forward, Camp-On, etc) will be kept.

3.2 Resetting the System

The system reset is carried out using the "Power OFF and ON" operation.

Hardware Manual 3-7

SL1100 ISSUE 1.0

Memo

3-8 System Start Up

Maintenance
SECTION 1 FUSE REPLACEMENT
4
1.1 Replacing the Fuse

Maintenance
This fuse is only for external battery box connection, it is not used for AC power
to the system.

If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
1. Turn off the system power and disconnect AC cord.
2. Open and remove the Sub-Cover.

Tab

Sub-Cover

Tab

Sub-Cover

Figure 4-1 Removing the Sub-Cover

3. Loosen two screws and remove the Main-Cover.

Hardware Manual 4-1

SL1100 ISSUE 1.0

Main-Cover
Two screws

Hooks

Figure 4-2 Removing the Main-Cover

4. Exchange the fuse (250 V/8 A) on 084M-B1 PCB.

084M-B1

FUSE (8 A / 250 V)

< Top View >

Figure 4-3 Exchanging the Fuse

5. Replace the Main-Cover and fasten two screws.

4-2 Maintenance
ISSUE 1.0 SL1100

Main-Cover
Two screws

Hooks

Figure 4-4 Replacing the Main-Cover

Hardware Manual 4-3

SL1100 ISSUE 1.0

SECTION 2 LITHIUM BATTERY REPLACEMENT

2.1 General
The Lithium Battery (CR2032) is installed on the CPU Card in Main KSU. It provides the battery-
backup of the RAM memory for approximately 36 months. When the battery power becomes low, the
system will display a "Warning Message" to the assigned Display Multiline Telephone as below.

11-10 WED 1:49PM

Low battery!
Menu Dir VM:00 CL:00

Figure 4-5 Warning of Low Battery

2.2 Lithium Battery Specification

Before replacing the Lithium battery, make sure which type of Lithium battery is required and prepare
the new Lithium battery. (CR2032)

NEC recommends that a backup of the customer data is performed before

powering off the system (either PCPro file or CF card backup) in order to replace
the backup battery.
• Risk of explosion if the battery is replaced by an incorrect type.
• Dispose of used batteries as instructed by the manufacturer of the battery.
• If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.

2.3 Replacing the Lithium Battery

1. Remove the Sub-Cover at the Main KSU.

Tab

Sub-Cover

Tab

Figure 4-6 Removing the Sub-Cover

4-4 Maintenance
ISSUE 1.0 SL1100

2. Power off the system, and remove the AC plug from the AC outlet.
3. Disconnect the AC power cord from the KSU.

AC power cord must be disconnected, otherwise the Main-Cover cannot be

opened.

Disconnect

AC Power Cord

Figure 4-7 Disconnecting the AC Power Cord

4. Loosen two screws and remove the Main-Cover.

Main-Cover
Two screws

Hooks

Figure 4-8 Removing the Main-Cover

5. Press tab A and lift the CPU support bracket.
6. Remove CPU card from the Main KSU.

Hardware Manual 4-5

SL1100 ISSUE 1.0

CPU card

CPU support

084M-B1 at 1228M KSU

Figure 4-9 Removing the CPU Card
7. Refer to following figure for the Lithium battery location on the CPU card.

CPU card

J12

< Conductor side > Battery socket

Figure 4-10 Location of Lithium Battery Socket
8. Remove the old Lithium battery and insert the new one into the socket.

The polarity “+” symbol must be on top as illustrated in following figure.

Lithium battery

Socket
Figure 4-11 Removing the Lithium Battery

4-6 Maintenance
ISSUE 1.0 SL1100

Lithium battery

Socket
Figure 4-12 Inserting the Lithium Battery

9. Reinstall the CPU card into the 084M-B1 mother board and close the CPU support bracket.

CPU card

CPU support

084M-B1 at 1228M KSU

Figure 4-13 Installing the CPU Card
10. Replace the Main-Cover and Sub-Cover.

Hardware Manual 4-7

SL1100 ISSUE 1.0

SECTION 3 MAIN SOFTWARE UPGRADING

3.1 General
The main system software is initially stored in the Flash memory located on the CPU card of the Main
KSU. It can be upgraded by the new software on the CF (Compact Flash) card.

3.2 Before Upgrading the Main Software

NEC recommends that a backup of the customer data is performed before

upgrading the main software (either PCPro file or CF card backup).

Before upgrading the main system software, the following preparations are necessary.
• Prepare the CF Card (32MB, or upwards and formatting by FAT(16)), and store the new main
software on the CF card by PC. (New main system software is supplied by NEC.)

3.3 Main Software Version Confirmation

The main system software version is confirmed by the following operation at the display type Multiline
Telephone.
The following steps assume that program 15-02-60 is set to Advanced 1 or Advanced 2. If set to Standard the
operation is as follows:
1. On-hook Condition.
2. Press Enter Key (Navigation Key).
3. Press "3" On Keypad to show the Main System Software version and Hardware Key Code.

1. On-hook Condition.

11-10 WED 1:49PM

200
Menu Dir VM:00 CL:00
Figure 4-14 Display of Multiline Telephone
2. Press Enter Key (Navigation Key).

10:Volume Preferences

Prev Next Select Exit

3. Dial 93.

93:Option Preferences
System Information
Prev Next Select Back

4. Press Enter Key (Navigation Key) to show the main system software version and Hardware Key
Code.

VERSION: 01.00
MAC: 00-60-B9-D8-DF-8E
HKEY: 2810-0000-0000

4-8 Maintenance
ISSUE 1.0 SL1100

5. Off-Hook and return to Time & Date mode.

11-10 WED 1:49PM

200
Menu Dir VM:00 CL:00

3.4 Upgrading the Main Software

If Expansion KSU(s) are installed, turn the power on/off in the order of Expan-
sion 2 KSU, Expansion 1 KSU and then Main KSU.
1. Power off the system and disconnect the AC cord from the KSU.
2. Remove the Sub-Cover.

Tab

Sub-Cover

Tab

Figure 4-15 Removing the Sub-Cover

3. Loosen two screws and remove the Main-Cover.

Main-Cover
Two screws

Hooks

Figure 4-16 Removing the Main-Cover

4. Insert the CF card (with the new main system software loaded) to the CF slot on VMDB daughter
board.

Hardware Manual 4-9

SL1100 ISSUE 1.0

CPU card

CF Slot (CN2)
CF card VMDB
D2 (Red)
D1 (Blue)
D3 (Red)
D4 (Red)

D5 (Red)

Figure 4-17 Inserting the CF card

5. Push in and hold the LOAD button (S1 on the CPU card).

Tab

Sub-Cover CPU card

S1
Tab

LOAD

< Front view >

Figure 4-18 LOAD Button (S1) Location

6. Turn the system power on.
7. Continue holding the LOAD button (S1) for approximately 10 seconds or until Status LED (D5)
starts flashing red.
8. Release the LOAD button (S1).
9. Wait until the Status LEDs (D2 to D5) on the CPU card has the following indications (approxi-
mately two minutes).

Table 4-1 Status LEDs

LED No. Indication Remarks

D2 Flashing Red

D3 Flashing Red

D4 Flashing Red

D5 Off

10. Turn the power off and remove the CF card from the CF slot on VMDB.

4-10 Maintenance
ISSUE 1.0 SL1100

CPU card

CF Slot (CN2)
CF card
VMDB

Figure 4-19 Removing the CF card

11. Replace the Main-Cover and Sub-Cover.
12. Turn the system power back on.
13. When the system has completed reloading the software, the RUN LED (D1) will flash blue.
• To confirm the new software version number, press the Navigation key on any display telephone to view the
system version number see Main Software Version Confirmation on page 4-8.
• The existing system data in the flash memory is replaced, but the customer data (stored in the RAM) is
saved.

Hardware Manual 4-11

SL1100 ISSUE 1.0

SECTION 4 LED INDICATIONS

The LEDs on the CPU indicate the following:
• RUN (D1) = The CPU is operating (Blue)
• D2, and D3 = Alarms (Red)
• D4 = Flash access indication (Red)
• D5 = Boot status (Red)
• Refer to Program 90-10: System Alarm Setup for details on assigning alarm LEDs.

Table 4-2 CPU LED Indications on this page provides a list of each LED and associated operation
and status indications. Refer to Figure 4-17 Inserting the CF card on page 4-10 for the location of the
LEDs on the CPU.

Table 4-2 CPU LED Indications

Status LED Indication

RUN (D1) D2 D3 D4 D5
System Operating Normally Blinking Off Off Off Off

System Operate Normal + File accessing Blinking Off Off Access Off
Blinking

System Starting Up On Off Off Off Off

Boot is starting On Off Off Off Blinking

Initializing the disk or formatting Blinking Off Off Off Off

Reading System Program Blinking Off On Access Off

Blinking

Reading Error of System Program Off On Off Off Off

System Initializing + DSP loading process On Off On Access Off

Blinking

Initializing System Program Blinking Off On Access Off

Blinking

Upgrading System Program (in the Flash Memory) Off Blinking Off Access Off
Blinking

Batch file Error Off On On Off Off

Completed the System Program Upgrade Off Blinking Blinking Blinking Off

Security Tip Error Off Blinking Off Off Off

Error alarm (Major) occurred Blinking Blinking Off Off Off

Error alarm (Minor) occurred Blinking Blinking Off Off Off

Shutting Down Blinking Off Off Off Off

Power Off Off Off Off Off Off

4-12 Maintenance
Specifications
SECTION 1 SYSTEM CAPACITY
5
Table 5-1 System Capacity

Specifications
Items 1 KSU 2 KSU 3 KSU Note
(1228) (2456) (3684)
Expansion Slot 2 4 6

System Maximum Port 52 104 144 1KSU: 084M+PRI+080E+4COIDBx2

2KSU: (084M+PRI+080E)x2+4COIDBx4
3KSU: 084Mx3+PRIx2+080Ex4+4COIDBx7

Trunk Port Max. 32 64 76 1KSU: PRIx1+4COIDBx2

2KSU: PRIx2+4COIDBx4
3KSU: PRIx2+4COIDBx7

Trunk Port Analog Trunks 12 24 36 1KSU: 4COIDBx3 on 084M/080E/008E

(COT) 2KSU: 4COIDBx6
3KSU: 4COIDBx9

PRI (24B) 24 48 48 Max. one PRI/KSU

Max. two PRIs/system

IP Trunk (SIP) 32

Station Port Max. 28 56 84 1KSU: 084M+080Ex2

2KSU: 084Mx2+080Ex4
3KSU: 084Mx3+080Ex6

Station Port 2W Key Set 24 48 72 Max. 24/KSU

084M+080Ex2

SLT (–28V) 20 40 60 1KSU: 084M+008Ex2

2KSU: 084Mx2+008Ex6
3KSU: 084Mx3+008Ex9

2W DSS Console 12 Connect to digital extension Port at

084M/080E

Doorphone 2 4 6 2DPH I/F on 084M (analog extension port 3,

4)
Alternative use with SLT

SIP-MLT/ SIP Std. 64

terminal

VM/VRS 2 VM ports/ 4 VRS ports (default) CFVMS-C1

Channels (Total Max.16) Port increased by license.

4 VM ports/ 4 VRS ports (default) CFVML-C1

(Total Max.16) Port increased by license.

Virtual Extension 50

Relay 2 4 6 2 circuits on 084M

Power Failure Transfer 3 6 9 1 PFT circuit on 4COIDB (COI port 1 and PF

port)

External Paging (Audio Out) 1 2 3 1 audio-In/Out and 2 audio-In circuits on

084M.
External MOH (Audio In) 1 Select one of 084M for MOH/BGM.

External BGM (Audio In) 1

Hardware Manual 5-1

SL1100 ISSUE 1.0

Items 1 KSU 2 KSU 3 KSU Note

(1228) (2456) (3684)
Ethernet Port 1 1 circuit on CPU

Built-In Answering Machine 2 2 circuits on CPU

Channel

VoIP Channels 32 Port increased by license.

V.34 Modem 1 1 circuit on CPU-B1 (VMDB)

Conference Circuits 32 (Max. 16 parties per Conference)

*1
DSP Resource 32 For 1228M KSU (DSP on CPU)

- 32 64 For 1228ME EXP 32ch DSP on each

EXIFE-C1

DSP Sender*2 128

*1. Service Tone receiver, DTMF receiver, Caller ID sender / receiver, MF receiver, MFC receiver
*2. Service Tone sender, DTMF sender, MF sender, MFC sender

5-2 Specifications
ISSUE 1.0 SL1100

SECTION 2 SYSTEM SPECIFICATIONS

2.1 General Precautions

• Never attempt to insert wires, pins, etc. into the vents or other holes of the equipment.
• Do not use benzene, thinner, or the like, or any abrasive powder to clean the equipment. Wipe it with
a soft cloth.

2.2 Environmental Requirements

Meeting established environmental standards maximizes the life of the system. Be sure that the site is
not:
• In direct sunlight or in hot, cold or humid places.
• In dusty areas or in areas where sulfuric gases are produced.
• In places where shocks or vibrations are frequent or strong.
• In places where water or other fluids comes in contact with the equipment.
• In areas near high-frequency machines or electric welders.
• Near computers, telexes, microwaves, air conditioners, etc.
• Near radio antennas (including shortwave)

2.3 Operating Conditions

Table 5-2 Operating Conditions

Unit Operating Conditions

KSU, PCBs and Multiline Telephones Temperature: 0 to +40 degree C (32 to 104 degree F)
Humidity: 10 to 90(non-condensing)

Doorphone Box Temperature: -20 to +60 degree C (-4 to 140 degree F)

Humidity: 20 to 80(non-condensing)

2.4 Site Requirements

A KSU can only be wall-mounted, it can only be floor-mounted if the optional External Backup Battery
Box is installed.

2.5 AC Power Requirement

A dedicated 100V-120V/220V/230V/240V 50/60Hz circuit located within 2 meters of the KSU is
required. A separate dedicated AC outlet is necessary for each KSU.

Double Pole/Neutral Fusing

(Power supply fuses are located at both the L and N side.)

Table 5-3 Power Requirement

110VAC 120VAC 220VAC 230VAC 240VAC

Power Requirement 110 VAC@15 A 120 VAC@15 A 220 VAC@15 A 230 VAC@15 A 240 VAC@15 A

Power Consumption Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
128 VA 130VA 154 VA 154 VA 156 VA

3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total = 3KSU Total =
384 VA 390VA 462 VA 462 VA 468 VA

Input Voltage (Rated Voltage) 90 VAC to 264 VAC (100VAC/120VAC/220VAC/230VAC/240VAC)

Frequency 47 Hz - 63 Hz (Rated Frequency: 50/60 Hz)

Hardware Manual 5-3

SL1100 ISSUE 1.0

110VAC 120VAC 220VAC 230VAC 240VAC

Phase and Wire Single Phase, 2 Line + PE Type

Ground Requirement No.14 AWG Copper Wire

Feeding Voltage SLT: 20 mA/-27 V

AC Input I Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
1.16 A 1.08 A 0.70 A 0.67 A 0.65 A
3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total = 3 KSU Total =
3.48 A 3.24 A 2.10 A 2.01 A 1.95 A

KWh Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
0.128 KWh 0.130 KWh 0.154 KWh 0.154 KWh 0.156 KWh
3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total
=0.384 KWh =0.390 KWh =0.462 KWh =0.462 KWh =0.468 KWh

BTU(KWh x 3413) Main KSU = Main KSU = Main KSU = Main KSU = Main KSU =
437 BTU 444 BTU 526 BTU 526 BTU 532 BTU
3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total 3 KSU Total
=1311 BTU =1332 BTU =1578 BTU =1578 BTU =1596 BTU

2.6 Electrical Specifications <Power Supply> (KSU)

Table 5-4 Electrical Specifications of KSU

Item Specification
Output Voltage -27 V (81 W)

Related Voltage -27 V

Load Fluctuation -25.92 V to -28 V (-27.0 V ±4)

Output Current 3.0 A

Ripple/Noise 200 mVp-p or less

Noise -65 dBm or less

Over Voltage Protection -31.2 V to -36.9 V

Over Current Protection 3.3 A to 3.9 A

Load Capacity 5000 µF

2.7 IP Terminal Power Chart

Table 5-5 IP Terminal Power Chart

IEEE Label Indication (Maximum Current with All Options)

IP Terminal 802.3af
Class 48 VDC 27 VDC
IP4WW-24TIXH-C TEL Class 2 130 mA 6.2 W 235 mA 6.3 W

2.8 IEEE802.af Class Specification

Table 5-6 IEEE802.af Class Specification

IEEE802.af Minimum Maximum

Class 2 3.84 W 6.49 W

5-4 Specifications
ISSUE 1.0 SL1100

2.9 Mechanical Specifications

Table 5-7 Mechanical Specifications

Equipment Width Depth Height Weight Note

1228M-B KSU, 375 mm 115 mm 290 mm Approx. 2 kg
1228ME-B EXP (14.76 in) (4.53 in) (11.42 in) (70.55 oz)

External Backup Battery 500 mm 230 mm 340 mm 10.3 kg (excluding battery)

(19.69 in) (90.55 in) (13.39 in) (363.32 oz)
15.6 kg (including battery)
(550.27 oz)

Multiline Telephone 180 mm 221 mm 136 mm 0.90 kg

(7.09 in) (8.70 in) (5.35 in) (31.75 oz)

DSS Console 122 mm 221 mm 113 mm 0.45 kg

(4.80 in) (8.70 in) (4.45 in) (15.87 oz)

Doorphone 98 mm 28.5 mm 130 mm 0.2 kg

(3.89 in) (1.12 in) (5.12 in) (7.05 oz)

2.10 Optional Unit Mechanical Specifications

Table 5-8 Optional Unit Mechanical Specifications

Unit Width Depth Height Weight

IP4WW-VOIPDB-C1 66 mm 138 mm 18 mm 0.05 kg
(2.60 in) (5.43 in) (0.71 in) (1.76 oz)

IP4WW-080E-B1 160 mm 198 mm 32 mm 0.17 kg

(6.30 in) (7.80 in) (1.26 in) (6.00 oz)

IP4WW-008E-B1 160 mm 198 mm 32 mm 0.16 kg

(6.30 in) (7.80 in) (1.26 in) (5.64 oz)

IP4WW-4COIDB-B1 75 mm 170 mm 18 mm 0.08 kg

(2.95 in) (6.69 in) (0.71 in) (2.82 oz)

IP4WW-1PRIU-C1 160 mm 198 mm 32 mm 0.15 kg

(6.30 in) (7.80 in) (1.26 in) (5.29 oz)

IP4WW-EXIFB-C1 70 mm 115 mm 16 mm 0.04 kg

(2.76 in) (4.53 in) (0.63 in) (1.41 oz)

IP4WW-CFVMS-C1 43 mm 37 mm 3.5 mm 0.01 kg

(1.69 in) (1.46 in) (0.14 in) (0.35 oz)

IP4WW-CFVML-C1 43 mm 37 mm 3.5 mm 0.01 kg

(1.69 in) (1.46 in) (0.14 in) (0.35 oz)

2.11 Doorphone Interface Specifications

Table 5-9 Doorphone Interface Specifications

Item Specification
Output Impedance 600 Ω

Output Level Nominal 250 mV (-10 dBm)

Maximum Output 400 mV RMS

Hardware Manual 5-5

SL1100 ISSUE 1.0

2.12 General Purpose/Door Unlock Relay Specifications

Table 5-10 General Purpose/Door Unlock Relay Specifications

Item Specification
Rated Voltage DC 48 V Maximum

Rated Current DC 320 mA Maximum

Contact Normally Open

2.13 External Paging Output Specifications

Table 5-11 External Paging Output Specifications

Item Specification
Output Impedance 600 Ω @ 1 kHz

Output Level Nominal 250 mV (-10 dBm)

Maximum Output 400 mV RMS

2.14 BGM/ExMOH Source Input Specifications

Table 5-12 BGM/External MOH Source Input Specifications

Item Specification
Output Impedance 600 Ω @ 1 kHz

Input Level Nominal 250 mV (-10 dBm)

Maximum Input 1 V RMS

2.15 External Sensor Device Interface Specifications

Table 5-13 External Sensor Device Interface Specifications

Applied Voltage during Loop Current during Sensor Port Assignment

Sensor Off On
24 V Program10-03-05: 0
40 mA
5V Program10-03-05: 1

The External Sensor device configuration shall be assigned by system program and the programming
is different with a Sensor Type.

2.16 CPU Card LAN Port Specifications

Table 5-14 CPU Card LAN Port Specifications

Item Specification
Standard IEEE802.3 10Base-T and 100Base-TX Compliant

Access CSMA/CD

I/F (Layer 1) Speed: 10 Mbps/100 Mbps Auto Negotiation

Cable: CAT5 or better, Straight/Cross Auto Crossover

5-6 Specifications
ISSUE 1.0 SL1100

2.17 Cabling Requirements

• Do not run extension cable in parallel with the AC source, telex or computer etc. If the cables are
near cable runs to those devices, use shielded cable with grounded shields or install the cable in
conduit.
• When cables must be run on the floor, cable protectors must be used.
• Cable runs for Multiline Telephones, DSS Consoles, Single Line Telephones, and Doorphone Boxes
must be a dedicated, isolated cable pair.
• Aerial distribution cabling is not allowed.
• Trunk Lines must be installed with lightning protectors.
• Do not use 4-wire cabling for SLT connections.

2.18 Cable Requirements

Table 5-15 Cable Requirements

Device Cable Type Cable Run Length

Multiline Telephone 24 AWG (Φ0.5 mm) 300 m (984.3 ft)

Multiline IP Telephone CAT5 Straight Cable 100 m (328.1 ft)

DSS Console 24 AWG (Φ0.5 mm) 300 m (984.3 ft)

Single Line Telephone Analog Terminals 24 AWG (Φ0.5 mm) 1,125 m (3,691ft)
(20mA)

Doorphone Box 24 AWG (Φ0.5 mm) 150 m (492.1 ft)

CPU LAN Port to External Device Ethernet Cross Cable 100 m (328.1 ft)

CPU LAN Port to Switching Hub Ethernet Straight Cable 100 m (328.1 ft)

ISDN Terminal 4-wire, 24 AWG (Φ0.5 mm) 100 m (328.1 ft)

(P-MP Short -passive)
300 m (984.3 ft)
(P-MP Long -passive)
500 m (1,640.4 ft)
(P-P)

1228ME-B EXP Ethernet Straight Cable (Attached to 1.2 m (3.9 ft)

1228ME-B EXP)

Hardware Manual 5-7

SL1100 ISSUE 1.0

Memo

5-8 Specifications
ISSUE 1.0 SL1100

Memo

Hardware Manual 5-9

Hardware Manual
NEC Corporation

ISSUE 1.0