AUTOMATION and CONTROL SYSTEMS

SIZES and MODELS

32
AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

33
SEISMIC
IP65
TESTED
 INTERNATIONAL CERTIFICATES
UL CERTIFICATE

VALID CERTIFICATE IN THE USA AND CANADA

You can view the complete certficate on our website.

34
 INTERNATIONAL CERTIFICATES
SEISMIC (EARTHQUAKE) RESISTANCE
TEST REPORT
SEISMIC
1.7. Testing laboratory
TESTED
1. GENERAL DATA P&P LMC S.r.l.
via Pastrengo, 9
24068 Seriate (BG)

ZONE 3 SEISMIC (EARTHQUAKE)

1.1. Customer
ITALY
TEKPAN TEKNIK ELEKTRIK,
Ankara Asfalt 14. km. Istiklal Mh. 17. Sk. No.8 1.8. Test date
Ulucak Kemalpasa / Izmir

RESISTANCE TEST REPORT

October 17th – 18th – 19th – 22nd, 2012.
TURKEY
1.9. Responsibilities
1.2. Unit under test
A. Bonzi, test responsible
The tests were performed on the following unit: M. Civera, test engineer
• TEOS plus+ double door enclosure, with a total mass of 395 kg. D. Recalcati, test engineer

1.3. Manufacturer
TEKPAN TEKNIK ELEKTRIK.
2. TESTING PROCEDURES
‘Zone3’ All Teos series products are within the scope of
Zone 3 seismic resistance tests.
1.4. Reference documents 2.1. General remarks
To perform the tests, three reference directions have been considered for the unit: X (front - rear), Y
1.4.1. Contract documents
(side - side) and Z (vertical).
a. Offer P&P LMC No. OF-AB-041/12 rev.01, dated June 18 , 2012. th
The sequence of the tests for the unit has been:
b. Order Tekpan dated June 19rd, 2012.
• Seismic tests, performed in three directions (X, Y, Z) and consisted in:

‘Zone3’ test was conducted for double-door enclosures of

- vibration response investigation
1.4.2. Technical documents and standards
- earthquake
1. Telcordia Generic Requirement GR-63-CORE, NEBS Requirements: Physical Protection, Issue - vibration response investigation

size 1200 widthx2000+100 height and 600 mm depth, and

1, October 1995; All the applied vibrations were monodirectional.
2. IEC 60068-3-3: Environmental testing - Part 3: Guidance – Seismic test methods for equipment; Tests in Z direction were performed on a vertical shaking table moved by an electro-dynamic shaker.
3. IEC 60068-2-6: Environmental testing - Part 2: Tests - Test Fc: Vibration (sinusoidal); For the other excitation directions, a horizontal shaking table was used. Excitation directions are

covers all sizes and types of the Teos series.

shown in the photographs.
4. IEC 60068-2-57: Environmental testing - Part 2: Tests - Test Ff: Vibration - Time-history
method; All the performed tests are listed in the table of page from 15. Tests were numbered following the
chronological sequence.
5. ISO 2041 Vibration and Shock – Vocabulary.
2.2. Mounting techniques
1.5. Test objective

You can view the complete report on our website.

For all tests the unit was mounted in its intended operating configuration.
The purpose of the tests were to demonstrate that the unit behave in compliance with the requirements
stated in doc. |1| to |4| referring to a seismic risk classified as Zone 3. The unit was fixed to the shaking table with No. 12 M14 screws with a tightening torque of 80 Nm.

1.6. Tests overall results 2.3. Control and measuring positions

At the end of the tests, at a visual inspection, any damages on the unit were detected. During the tests, for the motion control the signal of a monoaxial accelerometer in the excitation
direction (CP1) was used. Moreover two triaxial accelerometers (MP1 and MP2) were placed on the
unit for the vibration measurement (see photos). In the table reported below are summarized model
and serial number of the transducers mounted in the control and measuring positions during the tests.

Ident ification Tit le

RT-AB-085/12, rev. 00 Seismic tests on double door enclosure Teos Plus+ page 4 of 69 Ident ification Tit le
On behalf of:Tekpan Teknik Elektrik - Ulucak Kemalpasa / Izmir - Turkey RT-AB-085/12, rev. 00 Seismic tests on double door enclosure Teos Plus+ page 5 of 69
On behalf of:Tekpan Teknik Elektrik - Ulucak Kemalpasa / Izmir - Turkey

SEISMIC
TESTED
1.7. Testing laboratory
1. GENERAL DATA
P&P LMC S.r.l.
1.1. Customer via Pastrengo, 9
24068 Seriate (BG)

ZONE 4 SEISMIC (EARTHQUAKE)

TEKPAN TEKNIK ELEKTRIK, ITALY
Ankara Asfalt 14. km. Istiklal Mh. 17. Sk. No.8
Ulucak Kemalpasa / Izmir 1.8. Test date
TURKEY October 17th – 18th, 2012.

1.2. Unit under test

The tests were performed on the following unit:
1.9.
A. Bonzi,
Responsibilities
test responsible
M. Civera, test engineer
RESISTANCE TEST REPORT
• TEOS Plus+ single door enclosure, with a total mass of 315 kg.
D. Recalcati, test engineer
1.3. Manufacturer

For ‘Zone 4’ seismic resistance tests, an enclosure

TEKPAN TEKNIK ELEKTRIK. 2. TESTING PROCEDURES

1.4. Reference documents

sized 800 width x 2000+100 height x 800 with an extra

2.1. General remarks
1.4.1. Contract documents To perform the tests, three reference directions have been considered for the unit: X (front - rear), Y
(side - side) and Z (vertical).
a. Offer P&P LMC No. OF-AB-041/12 rev.01, dated June 18 , 2012.

reinforced interior and welded plinth was used.

th

The sequence of the tests for the unit has been:

b. Order Tekpan dated June 19rd, 2012.
• Seismic tests, performed in three directions (X, Y, Z) and consisted in:
1.4.2. Technical documents and standards - vibration response investigation
- earthquake
1. Telcordia Generic Requirement GR-63-CORE, NEBS Requirements: Physical Protection, Issue - vibration response investigation
1, October 1995;

The abovementioned size and structure are required for

All the applied vibrations were monodirectional.
2. IEC 60068-3-3: Environmental testing - Part 3: Guidance – Seismic test methods for equipment;
Tests in Z direction were performed on a vertical shaking table moved by an electro-dynamic shaker.
3. IEC 60068-2-6: Environmental testing - Part 2: Tests - Test Fc: Vibration (sinusoidal); For the other excitation directions, a horizontal shaking table was used. Excitation directions are

your needs within the scope of ‘Zone 4’. Please contact our
shown in the photographs.
4. IEC 60068-2-57: Environmental testing - Part 2: Tests - Test Ff: Vibration - Time-history
method; All the performed tests are listed in the tables of page 15. Tests were numbered following the
chronological sequence.

sales department for your needs.

5. ISO 2041 Vibration and Shock – Vocabulary.
2.2. Mounting techniques
1.5. Test objective
For all tests the unit was mounted in its intended operating configuration.
The purpose of the tests were to demonstrate that the unit behave in compliance with the requirements
stated in doc.|1| to |4| referring to a seismic risk classified as Zone 4. The unit was fixed to the shaking table with No. 8 M14 screws with a tightening torque of 80 Nm.

1.6. Tests overall results

At the end of the tests, at a visual inspection, no damages on the unit were detected.
2.3. Control and measuring positions
During the tests, for the motion control the signal of a monoaxial accelerometer in the excitation
You can view the complete report on our website.
direction (CP1) was used. Moreover two triaxial accelerometers (MP1 and MP2) were placed on the
unit for the vibration measurement (see photos). In the table reported below are summarized model
and serial number of the transducers mounted in the control and measuring positions during the tests.

Ident ification Tit le

RT-AB-084/12, rev. 00 Seismic tests on single door enclosure Teos Plus+ page 4 of 69 Ident ification Tit le
On behalf of:Tekpan Teknik Elektrik - Ulucak Kemalpasa / Izmir - Turkey RT-AB-084/12, rev. 00 Seismic tests on single door enclosure Teos Plus+ page 5 of 69
On behalf of:Tekpan Teknik Elektrik - Ulucak Kemalpasa / Izmir - Turkey

GOST CERTIFICATE

You can view the complete certificate on our website.

SEISMIC
IP65
TESTED
POWERED FRAME STRUCTURE

Produced with a closed rail structure, Teos

enclosure rails are clamped with a special
non-welded clamping system. Their resistance
to both vertical and horizontal pressures is
extremely high compared to open rail structures.
This force enables full resistance for the
movement of the installed equipments and
resistance in overcurrents.

Turkish Patent No: TR 201009615Y

 CORROSION PROTECTION

Teos closed frame made by galvanized steel (DIN EN Manufactured from aliminum-cast (E-160) material, the rail
10142_00 DX51 D+Z) and coated iron-phosphated and connection corners do not corrode thanks to their aliminium
powder coated from outside of the surface. Non-powder structure.
coated inside surface can not corrade because of the
galvanized material style.

All coated parts respectively undergo the automatic

processes of washing, phosphating, deionized passivation-
drying- coating- firing and are treated with active coating.
70-90 μm epoxy polyester powder-coating
500 hour salt test resistance is acquired according to the
test results of this process.
8-10 μm fosfat

Metal

SEISMIC
IP65
TESTED
 EARTHING CONTINUITY

Placed on the aliminium corner combination, the earthing

hooks are tightly mounted on the uncoated inner surface
of the rails by means of eroding. Thereby, the earthing
continuity is ensured for all rails and their parts.

Placed on the bottom-top inner parts of the front door,

the earthing screw increases conductive surface. Thereby,
the front door is more efficiently grounded as the most
important part to be grounded.

Applied to all other cover plates, the earthing screws allow

for the complete earthing of all enclosure cover plates.
Furthermore, Toes Plus+ allows for earthing all parts by
use of special grounding washers.

38
CLASSY AND MODERN VIEW

SEISMIC
IP65
TESTED
 EASY ASSEMBLING AND LOGISTICAL ADVANTAGES

1 2

3 4

Offered as flat package, the TEOS Plus+ series is designed Offered as flat package, TEOS Plus+ series save space
for an easy mounting in a minimal amount of time. It does during transportation and storage.
not require angulation for the body and can be mounted
between 15-20 minutes by two people.
 FRONT DOOR

Lock and hinge

placed in four points.

Standard swing
handle lock

Wide Space and

Strong Door Rail
Since locking is performed on the rails, inner space
of the cover plates allows for a maximum efficiency.

As the closed support rails are manufactured as a

completely closed box, they are more resistant to
bending. This ensures a stronger cover plate.

Rigid and Durable Lock Structure

Lock failures experienced in most enclosures are prevented in TEOS Plus+. Thanks to
their corrugated and long-lasting structure, the locking plates do not bend and corrode.

SEISMIC
IP65
TESTED
PLINTH SYSTEM

Front surfaces of the corner parts are open in the plinth

system which is designed with a height of 100 mm and
200 mm. This enables not only an easy mounting on
the enclosure but also an easy ground fixing. Upon the
completion of this process, the plastic panel closes without
use of screws.

Plinth front panels are mounted with screws while the side
panels are screwed from the inside.

A separate corner can be used for plinth applications with

a height of 200 mm as well as plinths with a height of 100
mm can be superimposed to reach the 200 mm height.
 AUTOMATION and
CONTROL SYSTEMS Page 44-63

POWER / ENERGY
DISTRIBUTION SYSTEMS Page 64-89

SERIES
ACCESSORIES Page 90-109

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

44
AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

45
SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

46
AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

SEISMIC
IP65
TESTED
 IP 65 PROTECTION CATEGORY

Sealing foam gaskets are used on the All gaskets apply pressure on the convex With the help of the gasket, the
body door, back door, side panels and frame curves. Dust and water particles bottom base system enables complete
top panels of the enclosure. This gasket are left in the space between the convex protection from the frame contact
enables complete isolation between curves, and thus pressure on the gasket surface and on the contact point of the
-10°C and +50°C. is prevented. gland plate and bottom panel.
 IP 65 PROTECTION CATEGORY

Applied to double-door enclosures, the insulating Applied to all front doors and panels, the liquid seal
gasket assumes a full protective role between two is used in all double-door enclosures and acts as an
panels and the frame when both doors close over the insulator between two doors. Locking system of both
gasket. doors work separately and this enables a full gasket
pressing.

SEISMIC
IP65
TESTED
BOTTOM AND GLAND PLATE SYSTEM

Bottom part of the enclosure is closed by means of a

centre-bore closure system which allows for insulation.
According to their depth, the perforations in the middle
of bottom enclosure part are covered with 3-4 pieces of
galvanized steel. .

As partial gland plates are replacable, their position can

be changed according to needs. Plate positions can be
changed in single mounting plate or double mounting plate
applications.

Foam and brush options available.

(See page 92 for cable entry accessories).
 MOUNTING PLATE SYSTEM

Manufactured from a 3,00 mm galvanized steel, TEOS plus+ Connected to the mounting plates, the intermediate mounting
mounting plates are railed and easily mounted. With its thick plate increases space and can move back and front together
steel sheet structure, the mounting plate can carry heavy with the mounting plates.
equipment with its rigid structure and does not need additional
side support parts. In this way, bayed enclosure space is
increased in combined enclosures.

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

TOP / BOTTOM GROUP

Relevant Size : ENCLOSURE WIDTH x DEPTH
Material : Body : 1,50mm galvanized steel+RAL7035 powder-coating
Top Cover : 1,50mm mild steel +RAL7035 powder-coating
Bottom : 1,50mm mild steel + RAL7035 powder-coating
Gland Plate : 1,50mm galvanized steel

Supply includes : 1 set of upper body, 1 set of lower body, 1 pcs gland plate,
1 pcs top cover, 4 pcs lifting egebolts and body mounting parts.

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE
(W) (D) NO. (W) (D) NO. (W) (D) NO.
400 500 701.450 700 400 701.740 1000 400 701.040
400 600 701.460 700 500 701.750 1000 500 701.050
400 800 701.480 700 600 701.760 1000 600 701.060
600 400 701.640 700 800 701.780 1000 800 701.080
600 500 701.650 800 400 701.840 1200 400 701.240
600 600 701.660 800 500 701.850 1200 500 701.250
600 800 701.680 800 600 701.860 1200 600 701260
800 800 701.880 1200 800 701.280

VERTICAL FRAME GROUP

Relevant Size : ENCLOSURE HEIGHT

Material : Frame : 1,50mm galvanized steel +

RAL7035 powder-coating

Supply includes : 4 pcs vertical frame

WIDTH REFERENCE
(W) NO.
1200 702.120
1600 702.160
1800 702.180
2000 702.200
2200 702.220
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

PLINTH CORNER PART

Relevant Size : PLINTH HEIGHT

Material : Corner part : 2,00mm galvanized steel + RAL 7012

powder-coating
Plastic Panel : RAL 7012 ABS Plastic

Supply includes : 4 pcs 100 mm or 200mm high plinth corner part,

4 pcs plastic panel and mounting parts

Note : Please see page 90-91 for plinth accessories.

TEOS PLINTH REFERENCE

HEIGHT(H2) NO.
100 708.100
200 708.200

PLINTH FRONT COVERS PLINTH SIDE COVERS

Relevant Size : ENCLOSURE WIDTH Relevant Size : ENCLOSURE DEPTH

Material : 1,50mm galvanized steel + 1,50mm galvanized steel +

Material :
RAL 7012 powder-coating RAL 7012 powder-coating

Supply includes : 2 pcs 100mm high front plinth panel Supply includes : 2 pcs 100mm high side plinth panel
and mounting parts and mounting parts

Required : 2 sets of front plinth panel group Required : 2 sets of front plinth panel group
for 200mm height plinths. for 200mm high plinths.

ENCLOSURE REFERENCE
WIDTH(W) NO. ENCLOSURE REFERENCE
400 709.140 DEPTH(D) NO.
600 709.160 400 710.140
700 709.170 500 710.150
800 709.180 600 710.160
1000 709.100 800 710.180
1200 709.120

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

REAR PANEL GROUP

Relevant size : ENCLOSURE WIDTH x HEIGHT

1,50mm mild steel + RAL 7035 powder-coating

Material :

Supply includes : 1 pcs rear panel and mounting parts

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE
(W) (HT) NO. (W) (HT) NO. (W) (HT) NO.
400 1800 703.418 700 1800 703.718 1000 1800 703.018
400 2000 703.420 700 2000 703.720 1000 2000 703.020
600 1200 703.612 800 1200 703.812 1200 1200 703.212
600 1600 703.616 800 1600 703.816 1200 1600 703.216
600 1800 703.618 800 1800 703.818 1200 1800 703.218
600 2000 703.620 800 2000 703.820 1200 2000 703.220
600 2200 703.622 800 2200 703.822 1200 2200 703.222

SIDE PANELS

Relevant size : ENCLOSURE HEIGHT x DEPTH

1,50mm mild steel + RAL 7035 powder-coating

Material :

Supply includes : 2 pcs side panel and mounting parts

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

HEIGHT DEPTH REFERENCE HEIGHT DEPTH REFERENCE HEIGHT DEPTH REFERENCE
(H) (D) NO. (H) (D) NO. (H) (D) NO.
1200 400 706.124 1800 400 706.184 2000 400 706.204
1200 500 706.125 1800 500 706.185 2000 500 706.205
1200 600 706.126 1800 600 706.186 2000 600 706.206
1600 400 706.164 1800 800 706.188 2000 800 706.208
1600 500 706.165 2200 600 706.226
1600 600 706.166
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

SOLID FRONT DOOR GLAZED FRONT DOOR

Relevant size : ENCLOSURE WIDTH x HEIGHT

Material : Solid Door : 2,00mm mild steel + RAL 7035 powder-coating

Glazed Door : 2,00mm mild steel + RAL 7035 powder-coating
4,00mm tempered glass
Supply includes : Solid Door : 1 pcs solid door, 1 set of lock, 4 set hinges and door stiffeners
Glazed Door : 1 adet Glazed Door , 1 pcs glazed door, 1 set of lock, 4 sets of hinge and door support profile

Attention : 800mm and 1000mm wide enclosures come in both single and double-door versions. 1200mm wide enclosures come
only in double-door versions. Only 600mm and 800mm wide enclosures come with glazed doors.

Attention : Doors of the double-door version are delivered in two separate packages.

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

WIDTH HEIGHT DOOR REFERENCE WIDTH HEIGHT DOOR REFERENCE WIDTH HEIGHT DOOR REFERENCE
(W) (H) NO. (W) (H) NO. (W) (H) NO.
400 1800 Single 704.418 800 1200 Single 704.812 1000 1800 Double 704.018
400 2000 Single 704.420 800 1600 Single 704.816 1000 2000 Double 704.020
600 1200 Single 704.612 800 1800 Single 704.818 1000 2000 Single 704.021
600 1600 Single 704.616 800 1800 Double 704.811 1200 1200 Double 704.212
600 1800 Single 704.618 800 2000 Single 704.820 1200 1600 Double 704.216
600 2000 Single 704.620 800 2000 Double 704.821 1200 1800 Double 704.218
600 2200 Single 704.622 800 2200 Single 704.822 1200 2000 Double 704.220
700 1800 Single 704.718 1200 2200 Double 704.222
700 2000 Single 704.720
GLAZED DOOR GLAZED DOOR GLAZED DOOR
600 1800 Single 705.618 700 1800 Single 705.718 800 1800 Single 705.818
600 2000 Single 705.620 700 2000 Single 705.720 800 2000 Single 705.820

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

MOUNTING PLATE
Relevant size : ENCLOSURE WIDTH x HEIGHT

Material : 3,00mm Galvanized steel

Supply includes : 1 pcs mounting plate and mounting parts.

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE
(W) (H) NO. (W) (H) NO. (W) (H) NO.
600 1200 707.612 700 1800 707.718 1000 1800 707.018
600 1600 707.616 700 2000 707.720 1000 2000 707.020
600 1800 707.618 800 1200 707.812 1200 1200 707.212
600 2000 707.620 800 1600 707.816 1200 1600 707.216
600 2200 707.622 800 1800 707.818 1200 1800 707.218
800 2000 707.820 1200 2000 707.220
800 2200 707.822 1200 2200 707.222

INTERMEDIATE MOUNTING PLATE

Relevant size : ENCLOSURE HEIGHT

Material : 2,00 mm galvanized steel

Supply includes : 1 pcs mounting plate, 3 pcs bracket and mounting parts

ENCLOSURE REFERENCE
HEIGHT(H) NO.
1200 712.120
1600 712.160
1800 712.180
2000 712.200
2200 712.220
AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

MOUNTING PLATE FOR CORNER EXTENSION

Materyal : 2,00 mm Galvanized steel

Supply includes : 2 pcs extension parts and assembly parts.

ENCLOSURE REFERENCE
HEIGHT(H) NO.
1200 712.121
1600 712.161
1800 712.181
2000 712.201
2200 712.221

SHORT MOUNTING PLATE APPLICATION

Depth rails allow for use of shorter mounting plates inside the
enclosure. Thereby, this allows for busbar support and busbar
applications on the mounting plate.

Each mounting plate needs 2 pcs depth rails and 4 pcs brackets.
Please see page 75-77 for related products.

Please see page 160-180 for busbar support needs.

Attention : There is no inconvenience in using intermediate mounting

plates and corner extension parts for short mounting
plate applications. It can move front to back with
these accessories

MOUNTING PLATE LEANING SYSTEM

Used for placing the mounting plate in the backmost position inside
the enclosure.

Material : 2.00 mm mild steel + zinc coated

Supply includes : 2 pcs mounting plate bracket and assembly parts

Reference number : 943.465 (2 pcs)

Attention : Intermediate mounting plate and corner extension

parts cannot be used in the mounting plate leaning
application. Short mounting plate can be applied.

Required : 6 pcs bracket required.

SEISMIC
IP65
TESTED
AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

BAYING KIT
Material : 3,00mm - 4,00mm mild steel parts + zinc coated

Supply includes : 2 pcs combination, 4 pcs angular brackets,

2 pcs adjustable bracket, 4 pcs fixing bracket,
5,60m intermediate insulation gasket and mounting parts

Reference number : 711.000

Note : Please see page 105-107 for other combination and

support systems.
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

HEIGHT (H): 1200 mm

W D ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTHmm (W)
Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.640 701.840 701.240
H 2 VERTICAL FRAMES GROUP 702.120 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
H2 4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140
6 REAR PANEL 703.612 703.812 703.212
7 FRONT DOOR (SOLID) 704.612 704.812 704.212
8 SIDE PANELS (2 pcs.) 706.124 706.124 706.124
9 MOUNTING PLATE 707.612 707.812 707.212
10 BAYING KIT 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTHmm (W)

Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.650 701.850 701.250
2 VERTICAL FRAMES GROUP 702.120 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150 710.150
6 REAR PANEL 703.612 703.812 703.212
7 FRONT DOOR (SOLID) 704.612 704.812 704.212
8 SIDE PANELS (2 pcs.) 706.125 706.125 706.125
9 MOUNTING PLATE 707.612 707.812 707.212
10 BAYING KIT 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTHmm (W)

Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.660 701.860 701.260
2 VERTICAL FRAMES GROUP 702.120 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160
6 REAR PANEL 703.612 703.812 703.212
7 FRONT DOOR (SOLID) 704.612 704.812 704.212
8 SIDE PANELS (2 pcs.) 706.126 706.126 706.126
9 MOUNTING PLATE 707.612 707.812 707.212
10 BAYING KIT 711.000 711.000 711.000

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

HEIGHT (H): 1600 mm

W D ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTHmm (W)
Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.640 701.840 701.240
H 2 VERTICAL FRAMES GROUP 702.160 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
H2 4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140
6 REAR PANEL 703.616 703.816 703.216
7 FRONT DOOR (SOLID) 704.616 704.816 704.216
8 SIDE PANELS (2 pcs.) 706.164 706.164 706.164
9 MOUNTING PLATE 707.616 707.816 707.216
10 BAYING KIT 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTHmm (W)

Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.650 701.850 701.250
2 VERTICAL FRAMES GROUP 702.160 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150 710.150
6 REAR PANEL 703.616 703.816 703.216
7 FRONT DOOR (SOLID) 704.616 704.816 704.216
8 SIDE PANELS (2 pcs.) 706.165 706.165 706.165
9 MOUNTING PLATE 707.616 707.816 707.216
10 BAYING KIT 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTHmm (W)

Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.660 701.860 701.260
2 VERTICAL FRAMES GROUP 702.160 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160
6 REAR PANEL 703.616 703.816 703.216
7 FRONT DOOR (SOLID) 704.616 704.816 704.216
8 SIDE PANELS (2 pcs.) 706.166 706.166 706.166
9 MOUNTING PLATE 707.616 707.816 707.216
10 BAYING KIT 711.000 711.000 711.000
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS
HEIGHT (H): 1800 mm
ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door Single Door Double Door Double Door Double Door
STEP PRODUCT DESCRIPTION 600 700 800 800 1000 1200
1 TOP/BOTTOM GROUP 701.640 701.740 701.840 701.840 701.040 701.240
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.170 709.180 709.180 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140 710.140 710.140 710.140
6 REAR PANEL 703.618 703.718 703.818 703.818 703.018 703.218
7 FRONT DOOR (SOLID) 704.618 704.718 704.818 704.811 704.018 704.218
7 FRONT DOOR (GLAZED) 705.618 705.718 705.818 - - -
8 SIDE PANELS (2 pcs.) 706.184 706.184 706.184 706.184 706.184 706.184
9 MOUNTING PLATE 707.618 707.718 707.818 707.818 707.018 707.218
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1200
1 TOP/BOTTOM GROUP 701.450 701.650 701.750 701.850 701.850 701.050 701.250
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150 710.150 710.150 710.150 710.150 710.150
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018 703.218
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018 704.218
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - - -
8 SIDE PANELS (2 pcs.) 706.185 706.185 706.185 706.185 706.185 706.185 706.185
9 MOUNTING PLATE - 707.618 707.718 707.818 707.818 707.018 707.218
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1200
1 TOP/BOTTOM GROUP 701.460 701.660 701.760 701.860 701.860 701.060 701.260
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160 710.160 710.160 710.160 710.160
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018 703.218
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018 704.218
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - - -
8 SIDE PANELS (2 pcs.) 706.186 706.186 706.186 706.186 706.186 706.186 706.186
9 MOUNTING PLATE - 707.618 707.718 707.818 707.818 707.018 707.218
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 800 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1200
1 TOP/BOTTOM GROUP 701.480 701.680 701.780 701.880 701.880 701.080 701.280
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.180 710.180 710.180 710.180 710.180 710.180 710.180
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018 703.218
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018 704.218
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - - -
8 SIDE PANELS (2 pcs.) 706.188 706.188 706.188 706.188 706.188 706.188 706.188
9 MOUNTING PLATE - 707.618 707.718 707.818 707.818 707.018 707.218
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

SEISMIC
IP65
TESTED
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS
HEIGHT (H): 2000 mm
ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door Single Door Double Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 600 700 800 800 1000 1000 1200
1 TOP/BOTTOM GROUP 701.640 701.740 701.840 701.840 701.040 701.040 701.240
2 VERTICAL FRAMES GROUP 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.170 709.180 709.180 709.100 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140 710.140 710.140 710.140 710.140
6 REAR PANEL 703.620 703.720 703.820 703.820 703.020 703.020 703.220
7 FRONT DOOR (SOLID) 704.620 704.720 704.820 704.821 704.021 704.020 704.220
7 FRONT DOOR (GLAZED) 705.620 705.720 705.820 - - - -
8 SIDE PANELS (2 pcs) 706.204 706.204 706.204 706.204 706.204 706.204 706.204
9 MOUNTING PLATE 707.620 707.720 707.820 707.820 707.020 707.020 707.220
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000 1200
1 TOP/BOTTOM GROUP 701,450 701.650 701.750 701.850 701.850 701.050 701.050 701.250
2 VERTICAL FRAMES GROUP 702,200 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708,100 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708,200 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709,140 709.160 709.170 709.180 709.180 709.100 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710,150 710.150 710.150 710.150 710.150 710.150 710.150 710.150
6 REAR PANEL 703,420 703.620 703.720 703.820 703.820 703.020 703.020 703.220
7 FRONT DOOR (SOLID) 704,420 704.620 704.720 704.820 704.821 704.021 704.020 704.220
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - - -
8 SIDE PANELS (2 pcs) 706,205 706.205 706.205 706.205 706.205 706.205 706.205 706.205
9 MOUNTING PLATE - 707.620 707.720 707.820 707.820 707.020 707.020 707.220
10 BAYING KIT 711,000 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000 1200
1 TOP/BOTTOM GROUP 701,460 701.660 701.760 701.860 701.860 701.060 701.060 701.260
2 VERTICAL FRAMES GROUP 702,200 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708,100 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708,200 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709,140 709.160 709.170 709.180 709.180 709.100 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710,160 710.160 710.160 710.160 710.160 710.160 710.160 710.160
6 REAR PANEL 703,420 703.620 703.720 703.820 703.820 703.020 703.020 703.220
7 FRONT DOOR (SOLID) 704,420 704.620 704.720 704.820 704.821 704.021 704.020 704.220
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - - -
8 SIDE PANELS (2 pcs) 706,206 706.206 706.206 706.206 706.206 706.206 706.206 706.206
9 MOUNTING PLATE - 707.620 707.720 707.820 707.820 707.020 707.020 707.220
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 800 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000 1200
1 TOP/BOTTOM GROUP 701,480 701.680 701.780 701.880 701.880 701.080 701.080 701.280
2 VERTICAL FRAMES GROUP 702,200 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708,100 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708,200 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709,140 709.160 709.170 709.180 709.180 709.100 709.100 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710,180 710.180 710.180 710.180 710.180 710.180 710.180 710.180
6 REAR PANEL 703,420 703.620 703.720 703.820 703.820 703.020 703.020 703.220
7 FRONT DOOR (SOLID) 704,420 704.620 704.720 704.820 704.821 704.021 704.020 704.220
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - - -
8 SIDE PANELS (2 pcs) 706,208 706.208 706.208 706.208 706.208 706.208 706.208 706.208
9 MOUNTING PLATE - 707.620 707.720 707.820 707.820 707.020 707.020 707.220
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000 711.000
 AUTOMATION and CONTROL SYSTEMS
SIZES and MODELS

HEIGHT (H): 2200 mm

W D ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 800 1200
1 TOP/BOTTOM GROUP 701.660 701.860 701.260
H 2 VERTICAL FRAMES GROUP 702.220 702.220 702.220
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200
H2 4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180 709.120
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160
6 REAR PANEL 703.622 703.822 703.222
7 FRONT DOOR (SOLID) 704.622 704.822 704.222
8 SIDE PANELS (2 pcs) 706.226 706.226 706.226
9 MOUNTING PLATE 707.622 707.822 707.222
10 BAYING KIT 711.000 711.000 711.000

SEISMIC
IP65
TESTED
POWER/ ENERGY DISTRIBUTION SYSTEMS
POWER/ ENERGY DISTRIBUTION SYSTEMS

SEISMIC
IP65
TESTED
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

TOP / BOTTOM GROUP

(WITHOUT GLAND PLATE)
Material : Body : 1,50 mm galvanized steel + RAL 7035 coating
Top Panel : 1,50 mm mild steel + RAL 7035 coating

Supply includes : 1 set of upper body, 1 set of lower body, 1 pcs top panel,
4 pcs eyebolt and body assembling parts

TEOS standard ENCLOSURE mm TEOS standard ENCLOSURE mm TEOS standard ENCLOSURE mm

WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE
(W) (D) NO. (W) (D) NO. (W) (D) NO.
400 500 701.451 700 400 701.741 1000 400 701.041
400 600 701.461 700 500 701.751 1000 500 701.051
400 800 701.481 700 600 701.761 1000 600 701.061
600 400 701.641 700 800 701.781 1000 800 701.081
600 500 701.651 800 400 701.841
600 600 701.661 800 500 701.851
600 800 701.681 800 600 701.861
800 800 701.881

BASE SYSTEM/ GLAND PLATE

Materyal : Base : 1,50 mm mild steel + RAL 7035 coating

Gland plate : 1,50 mm galvanized steel

Supply includes : 1 pcs base, 1 set gland plate

TEOS standard ENCLOSURE mm TEOS standard ENCLOSURE mm TEOS standard ENCLOSURE mm

WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE WIDTH DEPTH REFERENCE
(W) (D) NO. (W) (D) NO. (W) (D) NO.
400 500 923.450 700 400 923.740 1000 400 923.040
400 600 923.460 700 500 923.750 1000 500 923.050
400 800 923.480 700 600 923.760 1000 600 923.060
600 400 923.640 700 800 923.780 1000 800 923.080
600 500 923.650 800 400 923.840
600 600 923.660 800 500 923.850
600 800 923.680 800 600 923.860
800 800 923.880
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

VERTICAL FRAME GROUP

Material : Body : 1,50mm galvanized steel + RAL 7035 powder-coating

Supply includes : 4 pcs vertical frame

WIDTH REFERENCE
(W) NO.
1200 702.120
1600 702.160
1800 702.180
2000 702.200
2200 702.220

PLINTH CORNER PART PLINTH FRONT COVER PLINTH SIDE COVER

Material : Material : Material :

Corner part : 2,00mm galvanized steel + 1,50mm galvanized steel + 100mm Baza Yan kapağı : 1,50mm galvanized
RAL 7012 powder-coating RAL 7012 powder-coating steel + RAL 7012 powder-coating
Plastic Panel : RAL 7012 ABS Plastic
Supply includes : 2 pcs 100mm height front Supply includes : 2 pcs 100mm height side
Supply includes : 4 pcs 100mm or 200mm plinth cover and mounting plinth cover and mounting
high plinth corner part, parts parts
4 pcs plastic panel and
mounting parts. Required : 2 sets of side plinth cover Required : 2 sets of side plinth panel
group for 200mm height group for 200mm height
plinths plinths

TEOS PLINTH REFERENCE ENCLOSURE REFERENCE ENCLOSURE REFERENCE

HEIGHT(H2) NO. WIDTH(W) NO. DEPTH(D) NO.
100 708.100 400 709.140 400 710.140
200 708.200 600 709.160 500 710.150
700 709.170 600 710.160
800 709.180 800 710.180
1000 709.100
1200 709.120

SEISMIC
IP65
TESTED
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

REAR PANEL GROUP

Materyal : 1,50mm mild steel + RAL 7035 powder-coating

Supply includes : 1 pcs back rear and mounting parts

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE WIDTH HEIGHT REFERENCE
(W) (HT) NO. (W) (HT) NO. (W) (HT) NO.
400 1800 703.418 700 1800 703.718 1000 1800 703.018
400 2000 703.420 700 2000 703.720 1000 2000 703.020
600 1200 703.612 800 1200 703.812 1200 1200 703.212
600 1600 703.616 800 1600 703.816 1200 1600 703.216
600 1800 703.618 800 1800 703.818 1200 1800 703.218
600 2000 703.620 800 2000 703.820 1200 2000 703.220
600 2200 703.622 800 2200 703.822 1200 2200 703.222

SIDE PANELS

Materyal : 1,50mm mild steel TEOS plus ENCLOSURE mm

+ RAL 7035
powder-coating HEIGHT DEPTH REFERENCE
(H) (D) NO.
Supply includes : 2 pcs side panels 1200 400 706.124
and mounting parts 1200 500 706.125
1200 600 706.126
1600 400 706.164
1600 500 706.165
1600 600 706.166

TEOS plus ENCLOSURE mm TEOS plus ENCLOSURE mm

HEIGHT DEPTH REFERENCE HEIGHT DEPTH REFERENCE
(H) (D) NO. (H) (D) NO.
1800 400 706.184 2000 400 706.204
1800 500 706.185 2000 500 706.205
1800 600 706.186 2000 600 706.206
1800 800 706.188 2000 800 706.208
2200 600 706.226
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

FRONT DOOR (SOLID) GLAZED FRONT DOOR

Material : 2,00mm mild steel + Material : 2,00mm mild steel +

RAL 7035 powder-coating RAL 7035 powder-coating
Supply includes : 1 pcs solid door, 1 set of lock, 4,00mm tempered glaze
4 sets of hinge and door support rails. Supply includes : 1 pcs glazed door, 1 set of lock,
4 sets of hinge and door support
Attention : There is both a single-door and double-door version of 800mm and 1000mm wide enclosures. 1200mm enclosures come
only with double-doors. 600mm and 800mm wide enclosures come only with glazed doors.
Attention : Doors of double-door models are delivered in two separate packages.

WIDTH HEIGHT DOOR REFERENCE WIDTH HEIGHT DOOR REFERENCE WIDTH HEIGHT DOOR REFERENCE
(W) (H) NO. (W) (H) NO. (W) (H) NO.
400 1800 Single 704.418 800 1200 Single 704.812 1000 1800 Double 704.018
400 2000 Single 704.420 800 1600 Single 704.816 1000 2000 Double 704.020
600 1200 Single 704.612 800 1800 Single 704.818 1000 2000 Single 704.021
600 1600 Single 704.616 800 1800 Double 704.811 1200 1200 Double 704.212
600 1800 Single 704.618 800 2000 Single 704.820 1200 1600 Double 704.216
600 2000 Single 704.620 800 2000 Double 704.821 1200 1800 Double 704.218
600 2200 Single 704.622 800 2200 Single 704.822 1200 2000 Double 704.220
700 1800 Single 704.718 1200 2200 Double 704.222
700 2000 Single 704.720
Glazed Door Glazed Door Glazed Door
600 1800 Single 705.618 700 1800 Single 705.718 800 1800 Single 705.818
600 2000 Single 705.620 700 2000 Single 705.720 800 2000 Single 705.820

BAYING KIT
Materyal : 3,00mm - 4,00mm mild steel parts zinc coated +
galvanized

Supply includes : 2 pcs combination angles, 4 pcs angular brackets,

2 pcs adjustable bracket, 4 pcs fixing bracket
5,60 insulation gasket and mounting parts

Reference No : 711.000

Note : Please see page 105-107

for other combination
and support systems.

SEISMIC
IP65
TESTED
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

HEIGHT (H): 1200 mm

W D ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.641 701.841
H 2 VERTICAL FRAMES GROUP 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
H2 4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140
6 REAR PANEL 703.612 703.812
7 FRONT DOOR (SOLID) 704.612 704.812
8 SIDE PANELS (2 pcs) 706.124 706.124
10 BAYING KIT 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.651 701.851
2 VERTICAL FRAMES GROUP 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150
6 REAR PANEL 703.612 703.812
7 FRONT DOOR (SOLID) 704.612 704.812
8 SIDE PANELS (2 pcs) 706.125 706.125
10 BAYING KIT 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.661 701.861
2 VERTICAL FRAMES GROUP 702.120 702.120
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160
6 REAR PANEL 703.612 703.812
7 FRONT DOOR (SOLID) 704.612 704.812
8 SIDE PANELS (2 pcs) 706.126 706.126
10 BAYING KIT 711.000 711.000
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

HEIGHT (H): 1600 mm

W D ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.641 701.841
H 2 VERTICAL FRAMES GROUP 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
H2 4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140
6 REAR PANEL 703.616 703.816
7 FRONT DOOR (SOLID) 704.616 704.816
8 SIDE PANELS (2 pcs) 706.164 706.164
10 BAYING KIT 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.651 701.851
2 VERTICAL FRAMES GROUP 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150
6 REAR PANEL 703.616 703.816
7 FRONT DOOR (SOLID) 704.616 704.816
8 SIDE PANELS (2 pcs) 706.165 706.165
10 BAYING KIT 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door
STEP PRODUCT DESCRIPTION 600 800
1 TOP/BOTTOM GROUP 701.661 701.861
2 VERTICAL FRAMES GROUP 702.160 702.160
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.180
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160
6 REAR PANEL 703.616 703.816
7 FRONT DOOR (SOLID) 704.616 704.816
8 SIDE PANELS (2 pcs) 706.166 706.166
10 BAYING KIT 711.000 711.000

SEISMIC
IP65
TESTED
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

HEIGHT (H): 1800 mm

ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 600 700 800 800 1000
1 TOP/BOTTOM GROUP 701.641 701.741 701.841 701.841 701.041
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.170 709.180 709.180 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140 710.140 710.140
6 REAR PANEL 703.618 703.718 703.818 703.818 703.018
7 FRONT DOOR (SOLID) 704.618 704.718 704.818 704.811 704.018
7 FRONT DOOR (GLAZED) 705.618 705.718 705.818 - -
8 SIDE PANELS (2 pcs) 706.184 706.184 706.184 706.184 706.184
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000
1 TOP/BOTTOM GROUP 701.451 701.651 701.751 701.851 701.851 701.051
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150 710.150 710.150 710.150 710.150
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - -
8 SIDE PANELS (2 pcs) 706.185 706.185 706.185 706.185 706.185 706.185
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000
1 TOP/BOTTOM GROUP 701.461 701.661 701.761 701.861 701.861 701.061
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160 710.160 710.160 710.160
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - -
8 SIDE PANELS (2 pcs) 706.186 706.186 706.186 706.186 706.186 706.186
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 800 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000
1 TOP/BOTTOM GROUP 701.481 701.681 701.781 701.881 701.881 701.081
2 VERTICAL FRAMES GROUP 702.180 702.180 702.180 702.180 702.180 702.180
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.180 710.180 710.180 710.180 710.180 710.180
6 REAR PANEL 703.418 703.618 703.718 703.818 703.818 703.018
7 FRONT DOOR (SOLID) 704.418 704.618 704.718 704.818 704.811 704.018
7 FRONT DOOR (GLAZED) - 705.618 705.718 705.818 - -
8 SIDE PANELS (2 pcs) 706.188 706.188 706.188 706.188 706.188 706.188
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000
 POWER/ ENERGY DISTRIBUTION SYSTEMS
SIZES and MODELS

HEIGHT (H): 2000 mm

ENCLOSURE DEPTH 400 mm (D) ENCLOSURE WIDTH mm (W)
Single Door Single Door Single Door Double Door Single Door Double Door
STEP PRODUCT DESCRIPTION 600 700 800 800 1000 1000
1 TOP/BOTTOM GROUP 701.641 701.741 701.841 701.841 701.041 701.041
2 VERTICAL FRAMES GROUP 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.160 709.170 709.180 709.180 709.100 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.140 710.140 710.140 710.140 710.140 710.140
6 REAR PANEL 703.620 703.720 703.820 703.820 703.020 703.020
7 FRONT DOOR (SOLID) 704.620 704.720 704.820 704.821 704.021 704.020
7 FRONT DOOR (GLAZED) 705.620 705.720 705.820 - - -
8 SIDE PANELS (2 pcs) 706.204 706.204 706.204 706.204 706.204 706.204
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 500 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000
1 TOP/BOTTOM GROUP 701.451 701.651 701.751 701.851 701.851 701.051 701.051
2 VERTICAL FRAMES GROUP 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.150 710.150 710.150 710.150 710.150 710.150 710.150
6 REAR PANEL 703.420 703.620 703.720 703.820 703.820 703.020 703.020
7 FRONT DOOR (SOLID) 704.420 704.620 704.720 704.820 704.821 704.021 704.020
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - -
8 SIDE PANELS (2 pcs) 706.205 706.205 706.205 706.205 706.205 706.205 706.205
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 600 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000
1 TOP/BOTTOM GROUP 701.461 701.661 701.761 701.861 701.861 701.061 701.061
2 VERTICAL FRAMES GROUP 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.160 710.160 710.160 710.160 710.160 710.160 710.160
6 REAR PANEL 703.420 703.620 703.720 703.820 703.820 703.020 703.020
7 FRONT DOOR (SOLID) 704.420 704.620 704.720 704.820 704.821 704.021 704.020
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - -
8 SIDE PANELS (2 pcs) 706.206 706.206 706.206 706.206 706.206 706.206 706.206
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

ENCLOSURE DEPTH 800 mm (D) ENCLOSURE WIDTH mm (W)

Single Door Single Door Single Door Single Door Double Door Single Door Double Door
STEP PRODUCT DESCRIPTION 400 600 700 800 800 1000 1000
1 TOP/BOTTOM GROUP 701.481 701.681 701.781 701.881 701.881 701.081 701.081
2 VERTICAL FRAMES GROUP 702.200 702.200 702.200 702.200 702.200 702.200 702.200
3 PLINTH CORNER PART H100mm (H2) 708.100 708.100 708.100 708.100 708.100 708.100 708.100
3 PLINTH CORNER PART H200mm (H2) 708.200 708.200 708.200 708.200 708.200 708.200 708.200
4 PLINTH FRONT COVERS H100mm (H2) 709.140 709.160 709.170 709.180 709.180 709.100 709.100
5 PLINTH SIDE COVERS H100mm (H2) 710.180 710.180 710.180 710.180 710.180 710.180 710.180
6 REAR PANEL 703.420 703.620 703.720 703.820 703.820 703.020 703.020
7 FRONT DOOR (SOLID) 704.420 704.620 704.720 704.820 704.821 704.021 704.020
7 FRONT DOOR (GLAZED) - 705.620 705.720 705.820 - - -
8 SIDE PANELS (2 pcs) 706.208 706.208 706.208 706.208 706.208 706.208 706.208
10 BAYING KIT 711.000 711.000 711.000 711.000 711.000 711.000 711.000

SEISMIC
IP65
TESTED
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

1
1 SCISSILE RAIL, page 75
50 x25 Perforated structure

2 HEAVY EQUIPMENT PROFILE, page 76

6

5 3 AUXILIARY RAIL, page 76

7
4 PLUG-IN RAIL BRACKET, page 77
3

6
5 ADJUSTABLE RAIL BRACKET,
page 78

6 ADJUSTABLE RAIL BRACKET, page 79

In terms of both width and
interior depth size, TEOS
body structure is designed 7
at the same coefficient rate.
AUXILIARY RAIL
The complete structure
BRACKET, page 80
inside the body is designed
at the 25mm coefficient.
Thus, the width rail can also
be installed on the depth rail.
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

SCISSILE RAIL SYSTEM (50x25 cross-section)

Material : 2.00 mm Mild steel + zinc coated

Supply includes : In product pack there is only rail included. Please be check
quantities of rails in pack on sheet below

Required : There is brackets required to assemble rail.

Please see page 77 to 79.

Kesme Detayı

It is designed for assembling electrical

equipments into the enclosure. It is given
advantages for assembling in 3D every
directions.

It is produced from 2 mm sheet thickness, thanks

to this advantage and with bended structure it
gives force.

There is standard sizes, also the rail can cut to

adjust required dimension.

The rail coated zinc after production. Thanks to

this coating all cutted edges protected against
corrosion.

To see using styles of rail, please see page 77

t0 84.

ENCLOSURE RAIL NET PACKS REFERENCE

DEPTH (D) LENGTH (mm) OF NO.
ENCLOSURE WIDTH(W) 400 291 2 944.422
500 391 2 944.423
ENCLOSURE WIDTH(W) 600 491 2 944.424
ENCLOSURE WIDTH(W) 700 591 2 944.432
ENCLOSURE WIDTH(W) 800 691 2 944.425
ENCLOSURE WIDTH(W) 1000 891 2 944.426
ENCLOSURE HEIGHT (H) 1200 1091 2 944.427
ENCLOSURE HEIGHT (H) 1600 1491 2 944.428
ENCLOSURE HEIGHT (H) 1800 1691 2 944.429
ENCLOSURE HEIGHT (H) 2000 1891 4 944.430
ENCLOSURE HEIGHT (H) 2200 2091 4 944.431

SEISMIC
IP65
TESTED
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

HEAVY EQUIPMENT PROFILE

Material : 3 mm Mild steel + zinc coated

Supply includes : 2 pcs rail and assembly screws

Used for mounting heavy equipments such as base mounting MCCB

and transformer.

ENCLOSURE RAIL NET PACKS REFERENCE

WIDTH(W) LENGTH (mm) OF NO.
400 360 2 998.540
600 560 2 998.560
700 660 2 998.570
800 760 2 998.580
1000 960 2 998.510

Heavy Equipment application Heavy Equipment application Application with adjustable

on rails on base flat busbar support
Required :It is required to fixing on Required :It is required to fixing on
frame, 4 pcs of M6 hide nut. frame, 4 pcs of M6 hide nut.
Page 97 Page 97

AUXILIARY RAIL

Materyal : 2 mm Mild steel + zinc coated

Supply includes : 1 pcs rail

Used as top tightener on busbar supports. It can be used as

freestanding or be fixed on the body with its bracket

Required : Page 80 for rail bracket and assembling parts.

ENCLOSURE RAIL NET PACKS REFERENCE

DEPTH(D) LENGTH (mm) OF NO.
400 291 1 998.640
500 391 1 998.650
600 491 1 998.660
800 691 1 998.680
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

PLUG-IN RAIL BRACKET

Material : 2 mm mild steel + zinc coated

Reference number : 944.421 (12 pcs.) (Screws included)

944.420 (100 pcs.) (Screws included)

Thanks to this bracket, the enclosure body can be mounted, and the
scissile rail can be mounted on the enclosure body. It holds tightly on
the enclosure body thanks to its fitting hook. The low relief on the front
surface allows for a strong profile hold on the bracket and removes the
weight off the bolt.

Recommended for profile mounting on the body.

Moves on the profile or body at 25,00mm long steps.

Frame width and depth combination Vertical frame combination Frame top combination

Frame bottom combination Rail width combination (vertical) Rail width combination (horizontal)

Vertical rail combination Mounting plate combination

SEISMIC
IP65
TESTED
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

ADJUSTABLE RAIL BRACKET (TYPE T)

Material : 2 mm mild steel + zinc coated

reference number : 944.433 (4 pcs) ( screws included)

Used for mounting the scissile rail on the enclosure body.

Its slot perforations provides the profile with a 25mm axis movement.

The rail is able to reciprocate in vertical position. Thanks to this, the

equipments mounted on the rail can be aligned to the inner panel
position.

The busbar support is used to fix the top part on the body when the
rail is depth-combined on the body. See page 163

The bulge placed on the combination part of the bracket and the rail
holds the rail weight and takes the load off the screw.

25mm movement ability on

the axis

Depth combination on the frame Combination on the top frame

Vertical combination on the Vertical combination on the rail Width combination on the rail
frame (vertical)
 INTERIOR RAIL SYSTEM
SCISSILE RAIL SYSTEM

ADJUSTABLE RAIL BRACKET (TYPE L)

Material : 2 mm mild steel + zinc coated

Reference number : 944.434 (4 pcs) (screws included)

Used for mounting the scissile rail on the enclosure body.

Its slot perforations provides the profile with a 25mm axis movement

It is possible to adjust the equipment on the rail placed in the width

position according to the inner panel.

Positions the rail vertically on the enclosure and allows for busbar
support mounting. See page 163

25mm movement ability on

the axis

Width combination on the rail Frame depth combination

Frame top combination Frame bottom combination

(vertical) (vertical)

SEISMIC
IP65
TESTED
INNER RAIL SYSTEM
SCISSILE RAIL SYSTEM

AUXILIARY RAIL BRACKET

Materyal : 2 mm mild steel + zinc coated

Reference number : 944.435 (4 pcs) (bolts included)

It is brocket for fixing auxiliary rail on the depth frame.

The rail position can be adjusted with the help of the slot perforations
on the bracket which allow for a 25mm movement on its axis.

Used particularly for fixing the top part of the busbar supports on the
body.
 INNER RAIL SYSTEM
CIRCUIT BREAKER KITS

25A - 630A MCCB KIT

4x Kit Bracket

Material : 2 mm mild steel + zinc coated

Reference number : 944.436 (2 pcs.) (Screws included)

4 x Plug-in Rail Bracket (page 77)

Reference number : 944.420 (100 pcs.) (Screws included)

944.421 (12 adet) (Screws included)

2x Scissile Width Rail (page 75)

ENCLOSURE RAIL NET PACKS REFERENCE

WIDTH(W) LENGTH (mm) OF NO.
400 291 2 944.422
600 491 2 944.424

700 591 2 944.432
800 691 2 944.425

1x Part Mounting Plate page 84

This is the kit which enables compact MCCB (from lowest upto 630
Amperes) mounting.

As mounted from the front part of the enclosure, it makes it possible

for a copper busbar installation by creating space at the back of the
enclosure

Enables strong mounting with the plug-in rail bracket, and 7,00mm
reciprocating motion ability.

Offers a more economical solution as it eliminates the use of an entire

depth rail.

It is accord with cover plate.

SEISMIC
IP65
TESTED
 INTERIOR RAIL SYSTEM
CIRCUIT BREAKER KITS

MCB AND TERMINAL KIT (BACK-MOUNTED CABLE DUCT)

2x Kit Bracket

Material : 2 mm mild steel + zinc coated

Reference number : 944.436 (2 pcs.) (Screws included)

2x Plug-in rail bracket page 77

Reference number : 944.420 (100 pcs.) (Screws included)

944.421 (12 pcs.) (Screws included)

1x scissile width rail

ENCLOSURE RAIL NET PACKS REFERENCE

WIDTH(W) LENGTH (mm) OF NO.
400 291 2 944.422
600 491 2 944.424
700 591 2 944.432
800 691 2 944.425

1x terminal / MCB rail H7,5 mm (2 meter) page 211

Reference number : 990.102 (1 pcs.)

3x duct bracket

Material : 2 mm mild steel + zinc coated

Reference number : 944.437 (12 pcs.) (Screws included)

Mounts MCBs and terminals on the front enclosure panel without

depth profiles.

Enables to connect cable ducts from the rear for MCB mountings and
mount a maximum number of MCBs.

Suitable size: 60x60mm for vertical ducts and 40x60mm for horizontal
cable duct layings

Mounted on the enclosure body, the mounting kits are designed with
7,00mm stepping perforations and enable mounting both on the
MCBs and the terminal boxes.

Maximum number of MCBs on the mounting rail:

Enclosure Width MCB Capacity

400 10
600 22
700 27
800 33
 INTERIOR RAIL SYSTEM
CIRCUIT BREAKER KITS

MCB KIT (FRONT-MOUNTED CABLE DUCT)

2x MCB kit:

Material : 2 mm mild steel + zinc coated

Reference number : 944.478 (2 pcs.) (Screws included)

1x Scissile width MCB rail.

ENCLOSURE RAIL NET PACKS REFERENCE

WIDTH(W) LENGTH (mm) OF NO.
400 141 1 944.438
600 341 1 944.439
700 441 1 944.440
800 541 1 944.441

2x duct bracket

Material : 2 mm mild steel + zinc coated

Reference number : 944.437 (12 pcs.) (Screws included)

1x terminal / MCB rail H7,5 mm (2 meter) (page 211)

Reference number : 990.102 (1 pcs.)

Mounts the MCBs on the front enclosure body without depth rails.

Cable ducts can be connected from the front for MCB mountings.

Suitable size: 60x60mm for vertical cables and 40x60mm for

horizontal cable duct layings

Maximum number of MCBs on the mounting rail:

Enclosure Width MCB Capacity

400 5
600 16
700 22
800 27

SEISMIC
IP65
TESTED
 İÇ ATKI SİSTEMİ
PARTIAL MOUNTING PLATE

PARTIAL MOUNTING PLATE

Material : 2,00 mm galvanized steel.

Supply includes : 1 pcs. mounting plate

Required : 4 pcs plug-in rail bracket required for mounting

the mounting plate. Page 77
Reference number: 944.420 (100 pcs.) (Screws included)
944.421 (12 pcs.) (Screws included)

ENCLOSURE PLATE NET PLATE NET PACKS REFERENCE

WIDTH(W) WIDTH(mm) HEIGHT(mm) OF NO.
400 295 150 1 944.442
ENCLOSURE DEPTH (D)

400 295 175 1 944.443

400 295 200 1 944.444
400 295 250 1 944.445
400 295 300 1 944.446
400 295 400 1 944.447
400 295 500 1 944.448
400 295 600 1 944.449
500 395 400 1 944.450
D

600 495 150 1 944.451

ENCLOSURE DEPTH (D)

600 495 175 1 944.452

600 495 200 1 944.453
600 495 250 1 944.454
600 495 300 1 944.455
600 495 400 1 944.456
Application on MCCB kit, page 81 600 495 500 1 944.457
600 495 600 1 944.458
700 595 150 1 944.459
700 595 175 1 944.460
700 595 200 1 944.461
700 595 250 1 944.462
700 595 300 1 944.463
700 595 400 1 944.464
700 595 500 1 944.465
700 595 600 1 944.466
800 695 150 1 944.467
944.468
ENCLOSURE DEPTH (D)

800 695 175 1

800 695 200 1 944.469
800 695 250 1 944.470
800 695 300 1 944.471
800 695 400 1 944.472
800 695 500 1 944.473
800 695 600 1 944.474
Application on enclosure frame
1000 895 175 1 944.475
1000 895 200 1 944.476
1000 895 250 1 944.477
BUSBAR SUPPORT SYSTEM

According to Busbar Supports

see page 160-181

SEISMIC
IP65
TESTED
 COVER PLATE SYSTEM

For covering off the electrical equipment from the front of enclosure.
Modular structure and optional-combination
Fixed cover plate application is standard. The panels can move with
additional hinge supplies.
With cover plate bracket profile, cover plate can be partially or entirely
hinged.

1 Cover plate frame set.

Page 87

1
2 Cover plate. Page 88

3 Cover Plate. Page 89

1
4

4 Bracket profile for

cover plate. Page 89

5 Cable protector. Page 89

 COVER PLATE SYSTEM

COVER PLATE FRAME SET

Material : 1,50 mm mild steel + RAL 7035 coating

Supply includes : 2 pcs vertical profile, 2 pcs bottom-top closer,

2 pcs bottom-top cover plate, 4 pcs cable protection
and assembly parts.

Attention : You can find the size of the vertical inner panel profile in
the drawing and table. Cover plate sizes will be
determined according to this size.

ENCLOSURE ENCLOSURE COVER FRAME NET REFERENCE

WIDTH(W) HEIGHT(H) HEIGHT (H1)(mm) NO.
400 1800 1600 943.401
2000 1800 943.402
600 1200 1000 943.403
1600 1400 943.404
1800 1600 943.405
2000 1800 943.406
700 1800 1600 943.407
2000 1800 943.408
800 1200 1000 943.409
1600 1400 943.410
H1

1800 1600 943.411

2000 1800 943.412

SEISMIC
IP65
TESTED
 COVER PLATE SYSTEM

COVER PLATE

Material : 1,50 mm mild steel + RAL 7035 coating

Supply includes : 1 pcs cover plate and mounting parts

Required : To make hinged cover plate, it is required to select

2 pcs hinge page 89

ENCLOSURE PLATE NET PLATE NET MCB REFERENCE

WIDTH (W) WIDTH (W1) HEIGHT (H1) QTY NO.
400 247 50 943.413
100 943.414
150 943.415
150W 10 943.416
150C 943.417
200 943.418
200W 10 943.419
200C 943.420
300 943.421
400 943.422
550 943.423
600 943.424
10,5 600 447 50 943.425
100 943.426
150 943.427
24,5

150W 22 943.428
H1

150C 943.429
200 943.430
200W 22 943.431
943.432
W1
200C
300 943.433
400 943.434
550 943.435
600 943.436
700 547 50 943.437
150W , 200W 100 943.438
26,5 26,51 150 943.439
150W 27 943.440
150C 943.441
200 943.442
47

H1

200W 27 943.443
W1
200C 943.444
300 943.445
400 943.446
550 943.447
600 943.448
800 647 50 943.449
100 943.450
150C , 200C 150 943.451
150W 33 943.452
150C 943.453
200 943.454
H1

200W 33 943.455
200C 943.456
W1
300 943.457
400 943.458
550 943.459
600 943.460
 COVER PLATE SYSTEM

COVER PLATE HINGE

Material : Zamac 5 ABS plastic

Supply includes : 10 set hinge

Reference number : 950.108 (10 pcs)

BRACKET PFOFILE FOR COVER PLATE

Material : 1,50 mm mild steel + RAL 7035 coating

Supply includes : 1 pc profile and assembly parts

TEOS ENCLOSURE COVER FRAME PACKS REFERENCE

HEIGHT(H) NET HEIGHT(mm) OF NO.
1200 1000 1 943.461
1600 1400 1 943.462
1800 1600 1 943.463
2000 1800 1 943.464

CABLE PROTECTOR

Material : PVC rubber

Reference No : 950.109 (10 pcs)

SEISMIC
IP65
TESTED
 ACCESSORIES
PLINTH ACCESSORIES

FIXED PLINTH

Material : 3,00 mm / galvanized steel + RAL 7012 coating

Supply includes : Plinth width : 2 pcs plinth and combination parts.

Plinth depth : 2 pcs plinth and combination parts.

Required : It is required M12x30 screw set for fixing (page 215)

Mounts the enclosures combined side-to-side on a single platform.

Enclosures are connected to the plinth via M12 perforations placed on

the combination corners.

It gives advantages in the lifting and forklift. Please see page 108-109

Enclosures can be mounted directly on the (standard) plinth.

Please refer to our sales department for the manufacturing schedule.

ENCLOSURE REFERENCE ENCLOSURE REFERENCE

WIDTH (W) NO. WIDTH (W) NO.
1800 912.100 2900 912.111
1900 912.101 3000 912.112
2000 912.102 3100 912.113
2100 912.103 3200 912.114
2200 912.104 3300 912.115
2300 912.105 3400 912.116
2400 912.106 3500 912.117
2500 912.107 3600 912.118
2600 912.108 3700 912.119
2700 912.109 3800 912.120
2800 912.110 3900 912.121

ENCLOSURE REFERENCE ENCLOSURE REFERENCE

WIDTH (W) NO. DEPTH (D) NO.
4000 912.122 400 912.133
4100 912.123 500 912.134
4200 912.124 600 912.135
4300 912.125 800 912.136
4400 912.126
4500 912.127
4600 912.128
4700 912.129
4800 912.130
4900 912.131
5000 912.132
 ACCESSORIES
PLINTH ACCESSORIES

M12 LEVELING FEET

Supply includes : 4 pcs M12 Leveling Feet

Reference No : 995.510

SEISMIC
IP65
TESTED
 ACCESSORIES
GLAND PLATE / CABLE ENTRY ACCESSORIES

FOAM RUBBER CABLE ENTRY SYSTEM

Related Size : ENCLOSURE WIDTH

Material : Polyurethane foam

Supply includes : Polyurethane foam, combination profile and parts

Note : 2 accessories per (1000mm and 1200mm wide)

ENCLOSURE WIDTH(mm) REFERENCE NO. foam entry system
400 923.400
600 923.600 Attention : This application can only be used on teos plus+
or gland plate applications.
700 923.700
800 923.800
1000 * 923.100
1200 * 923.120

BRUSHED CABLE ENTRY SYSTEM

Related size : ENCLOSURE WIDTH

Material : ABS plastic

Supply includes : Strip brush, combination profile and parts

Note : 2 accessories per ( 1000mm and 1200mm wide)

brush entry system
ENCLOSURE WIDTH(mm) REFERENCE NO.
400 923.401 Attention : This application can only be used on teos plus+
600 923.601 or gland plate applications.
700 923.701
800 923.801
1000 * 923.101
1200 * 923.121

CABLE CLAMP RAIL (CLIP-ON)

Related size : ENCLOSURE WIDTH

Material : 2,00 mm mild steel + zinc-plating

Supply includes : Cable bracket combination profile and combination parts.

ENCLOSURE WIDTH(mm) REFERENCE NO. Attention : This application can only be used on teos plus+
or gland plate applications.
400 998.400
600 998.600
700 998.700
800 998.800
1000 998.100
1200 998.120
 ACCESSORIES
INTERIOR MOUNTING ACCESSORIES

MOUNTING PLATE in 2,00 mm sheet thickness

Material : 2,00 mm / galvanized steel

Supply includes : 1 pcs mounting plate and mounting parts.

Required : 2 pcs mounting plate bracket for supporting the mounting

plate from middle. 943.465 (2 pcs) page 94

Attention : 2 pcs scissile support rail for moving front to back the
mounting plate.

TEOS ENCLOSURE mm
WIDTH HEIGHT REFERENCE
(W) (H) NO.
600 1200 717.612
600 1600 717.616
600 1800 717.618
600 2000 717.620

TEOS ENCLOSURE mm
WIDTH HEIGHT REFERENCE
(W) (H) NO.
700 1800 717.718
700 2000 717.720
800 1200 717.812
800 1600 717.816
800 1800 717.818
800 2000 717.820

SEISMIC
IP65
TESTED
 ACCESSORIES
INTERIOR MOUNTING ACCESSORIES

MOUNTING PLATE BRACKET

Material : 2,00mm mild steel + zinc-coated

Supply includes : 2 pcs bracket and assembling screws.

Reference No : 943.465 (2 pcs)

Attention : 6 pcs part necessary for using the mounting plate at

the bottom-most inside the enclosure body.

This part can be used for centre-support in the mounting plates.

This part is needed for bottom-most use of the mounting plate.

Enables side-use for mounting plates

INTERMEDIATE MOUNTING PLATE

Related size : ENCLOSURE WIDTH

Material : 2,00 mm galvanized steel

Supply includes : 1 pcs mounting plate, 3 pcs bracket and assembling parts.

NCLOSURE WIDTH(mm) REFERENCE NO.

E
1200 712.120
1600 712.160
1800 712.180
2000 712.200
2200 712.220

EDGE EXTENSION FOR MOUNTING PLATE

Material : 2,00 mm galvanized steel

Supply includes : 2 pcs extension part and assembling parts

NCLOSURE HEIGHT(H)
E REFERENCE NO.
1200 712.121
1600 712.161
1800 712.181
2000 712.201
2200 712.221
 ACCESSORIES
INTERIOR MOUNTING ACCESSORIES

DIVIDING PANEL

Material : 1,5 mm Mild steel + RAL 7035 coating

Supply includes : 1 pcs panel and assembling parts.

Used for separating enclosures and mounting applications.

TEOS ENCLOSURE mm TEOS ENCLOSURE mm

HEIGHT DEPTH REFERANS HEIGHT DEPTH REFERANS
(H) (D) NO. (H) (D) NO.
1800 400 935.001 2000 400 935.005
1800 500 935.002 2000 500 935.006
1800 600 935.003 2000 600 935.007
1800 800 935.004 2000 800 935.008
2200 600 935.009

19’’ COMBINATION PROFILES

Material : 2,00mm mild steel+ zinc-plating

Supply includes : 4 pcs profile and combination screws

Required : 6 pcs scissile rail for 600mm width enclosure applications

on depth side of enclosure. In 800 mm width enclosures,
6 pcs 800 mm width adapter requires. See page 95

TEOS ENCLOSURE HEIGHT(H) UNIT U REFERENCE NO.

1200 24 944.930
1600 33 944.931
2000 42 944.932

800 mm WIDTH ADAPTER (19”)

Material : 2,00mm mild steel+ zinc-plating

Supply includes : 6 pcs adapter and assembling parts.

Reference No : Enclosure depth: 600 mm: 944.933

Enclosure depth: 800 mm: 944.934

SEISMIC
IP65
TESTED
 ACCESSORIES
INTERIOR MOUNTING ACCESSORIES

19’’ SWING FRAME

Material : 2,00 mild steel + RAL 7035 coating

Supply includes : 1 set of swing frame (lock-hinges included)

TEOS ENCLOSURE
WIDTH HEIGHT UNIT REFERANS
(W) (H) U NO.
600 1200 22 944.935
1600 31 944.936
1800 36 944.937
2000 40 944.938
2200 45 944.939

TEOS ENCLOSURE
WIDTH HEIGHT UNIT REFERANS
(W) (H) U NO.
800 1200 22 944.940
1600 31 944.941
1800 36 944.942
2000 40 944.943
2200 45 944.944

FIXED and MOVABLE SHELF

Material : 1,50mm mild steel+RAL 7035 coating

Supply includes : 1 pcs shelf and combination parts.

TEOS ENCLOSURE TEOS ENCLOSURE

WIDTH DEPTH REFERANS WIDTH DEPTH REFERANS
(W) (D) NO. (W) (D) NO.
FIXED SHELF IN FULL SIZE FIXED SHELF IN FULL SIZE
600 600 945.200 800 600 945.202
800 945.201 800 945.203
MOVABLE SHELF IN FULL SIZE MOVABLE SHELF IN FULL SIZE
600 600 945.400 800 600 945.402
800 945.401 800 945.403
FIXED SHELF IN 19” SYTEM
600 945.204
800 945.205
MOVABLE SHELF IN 19” SYSTEM
600 945.404
800 945.405
 ACCESSORIES
INTERIOR MOUNTING ACCESSORIES

KNITTED EARTHING CABLE

Material : Copper-+tin-plating

Supply includes : 5 pcs cable and screws

Reference No : 991.202 (5 pcs)

M6 HIDE NUT

Necessary for installing the support and mounting rails on the enclosure.
Installed from square perforations placed on the front surface of closed
profiles.

Reference No : 994.170 (100 pcs packs)

SEISMIC
IP65
TESTED
 ACCESSORIES
DOOR ACCESSORIES

SWING LOCK INSERT APPLICATIONS SWING LOCK KEYS

Reference No : 4444 key : 950.104 Reference No : 4444 key : 952.301

Doublebit key : 950.105 Doublebit key : 952.101
6,50 mm triangle key : 950.106 6,50 mm triangle key : 952.200
7,00 mm square key : 950.107 7,00 mm square key : 952.201

DOOR RAIL FOR CABLE DUCT

Related size : ENCLOSURE WIDTH
Material : 2,00 mm mild steel + zinc-plating
Supply includes : 1 pcs door rail and assembling parts.

Attention Note : 2 pcs of door channel profile accessory needed for

800mm, 1000mm and 1200mm wide double doors.

ENCLOSURE WIDTH(mm) REFERENCE NO.

400 997.104
600 997.113
700 997.116
800 997.114
Double Door 800 997.118
1000 997.111
Double Door 1000 997.115
Double Door 1200 997.112

DOOR STOPPER
It is using for angle limitation door.

Reference No : 905.202

METAL PLAN POCKET

Related size : ENCLOSURE WIDTH
Material : 1,50 mm mild steel + RAL 7035 powder-coating
Supply includes : 1 pcs metal plan pocket and assembling parts

ENCLOSURE WIDTH(mm) REFERENCE NO.

400 994.704
600 994.706
700 994.707
800 994.708
Double Door 800 994.718
1000 994.711
Double Door 1000 994.710
Double Door 1200 994.712
 ACCESSORIES
LIGHTING ACCESSORIES

LED LIGHT ENCLOSURE LAMP (Screwed Type)

230V AC 6W
2 pcs of socket plugs + switch cable

Reference No : 901.110

Required : Lamp rail is required for fixing the lamp. See page 100.

LED LIGHT ENCLOSURE LAMP (Magnetic Type)

230V AC 6W
2 pcs of socket plugs + switch cable

Reference No : 901.120

DOOR LAMP SWITCH

230V, 3A ve IP 65 protectıon
Without cable

Reference No : 902.110

Required : Switch bracket for switch mounting.

(See other lighting accessories, page 100)

SEISMIC
IP65
TESTED
 ACCESSORIES
LIGHTING ACCESSORIES

LAMP RAIL

Related size : ENCLOSURE WIDTH

Material : 2,00mm mild steel + zinc-plating

Supply includes : 1 pcs lamp bracket rail and assembling parts

ENCLOSURE WIDTH(mm) REFERENCE NO.

400 903.204
600 903.206
700 903.207
800 903.208
1000 903.210
1200 903.212

SWITCH BRACKET

Material : 2,00mm mild steel + zinc-plating

Supply includes : 1 pcs switch bracket and assembling parts

Reference No : 903.300
 ACCESSORIES
AIR-CONDITIONING ACCESSORIES

ROOF TYPE VENTILATION FAN

Colour : RAL 7035

IP Protection : IP 54

Used Fan : Ebm

Used in 230V AC.

It ejects the heated air inside of the enclosure coming from vertical angle
to horizantal angle. From the reason type of fan which ejects the air with
horizantal angle, the counterpressure is at the minumum level. By this way it
makes active and economic cooling with less power/ consumption and low
fan cost.

İt requires sufficient size of air filters for compensation of the enclosure inside
pressure between fan force of gravity.

It suggests using at the situation which the maximum inside required

temprature is higher than or equal maximum outside temperature

Required max. inside temp. Outside max. temp

FAN FLOW FAN POWER REFERENCE NO.

560 m3/saat 58 W 982.202
970 m3/saat 85 W 982.203

SEISMIC
IP65
TESTED
 ACCESSORIES
AIR-CONDITIONING ACCESSORIES

FAN WITH FILTERS

Colour : RAL 7035

IP Protection : IP 54

Fan : Ebm

230V AC Voltage

It suggets using at the situation which the maximum inside required

temprature is higher than or equal maximum outside temprature.

At standard fans fix to eject air. For opposite the fan positions must be
changed.

FILTER SIZE AIR FLOW FAN POWER REFERENCE NO

150 x 150 mm 60 m /saat
3
19 W 983.131
250 x 250 mm 160 m3/saat 45 W 983.141
250 x 250 mm 450 m3/saat 64 W 983.151

AIR FILTERS

Colour : RAL 7035

IP Protection : IP 54

FILTER SIZE REFERENCE NO

150 x 150 mm 983.106
250 x 250 mm 983.107
325 x 325 mm 983.110
 ACCESSORIES
AIR-CONDITIONING ACCESSORIES

PLEASE SEE PAGE 188-190 FOR

ENCLOSURE AIR-CONDITIONERS

PLEASE SEE PAGE 191-193 FOR

ENCLOSURE HEAT EXCHANGER

PLEASE SEE PAGE 194 FOR

ENCLOSURE HEATERS

PLEASE SEE PAGE 195 FOR

ENCLOSURE THERMOSTATS

SEISMIC
IP65
TESTED
 ACCESSORIES
FIRE PROTECTION and
EXTINQUISHING SYSTEMS

Please see page 196 - 201 for Fire Protection And Extinquishing Systems
 ACCESSORIES
ENCLOSURE BAYING / COMBINATING and
LIFTING ACCESSORIES

BAYING KIT GENERAL PACK (711.000

Please see page 58

1-) 2x Combination angles. Reference no: 711.001 (2 pcs)

2-) 4x Fixing bracket. Reference no: 711.002 (4 pcs)

3-) 4x angular brackets. Reference no: 711.003 (4 pcs)

4-) 2x adjustable bracket. Reference no: 711.004 (2 pcs)

5-) 5,60 m 10x3 gasket. Z: 992.100 (see page 211)

6-) Top angle iron lifting, page 106

7-) Fixed plinth, page 90

8-) Corner enclosure, page 107

SEISMIC
IP65
TESTED
 ACCESSORIES
ENCLOSURE BAYING / COMBINATING and
LIFTING ACCESSORIES

TOP ANGLE IRON COMBINATION

Material : 60x60 mm x 5 mm + RAL 7012 coating

Supply includes : 2 length angle bending

Required : 4 pcs M12x30 screw set is required for each enclosure.

See page 215.

This connection type is particularly used for heavy enclosure combination

and support applications. Do the supporting in accordance with supporting
instructions. Please see page 108-109 for supporting instructions.

Please refer to our sales department for the manufacturing schedule.

W
60

60

ANGLE BRACKET REFERENCE ANGLE BRACKET REFERENCE ANGLE BRACKET REFERENCE

WIDTH(mm) NO. WIDTH(mm) NO. WIDTH(mm) NO.
1800 912.137 2900 912.148 4000 912.159
1900 912.138 3000 912.149 4100 912.160
2000 912.139 3100 912.150 4200 912.161
2100 912.140 3200 912.151 4300 912.162
2200 912.141 3300 912.152 4400 912.163
2300 912.142 3400 912.153 4500 912.164
2400 912.143 3500 912.154 4600 912.165
2500 912.144 3600 912.155 4700 912.166
2600 912.145 3700 912.156 4800 912.167
2700 912.146 3800 912.157 4900 912.168
2800 912.147 3900 912.158 5000 912.169
 ACCESSORIES
ENCLOSURE BAYING / COMBINATING and
LIFTING ACCESSORIES

CORNER ENCLOSURE

Designed for enclosures when enclosures are

combined as an L. Door opening has been increased
by means of door suspending adapter.

Use the table below for corner enclosure options.

Bottom-top plinth frame and vertical frame group are
standard. Only the panel set and adapter group is
chosen in accordance with enclosure depth.

Inner enclosure applications and panel combination

parts can be applied as standard.

HEIGHT DEPTH REFERENCE

(H) (D) NO.
ADAPTER PART
1800 600 933.000
800 933.001
2000 600 933.002
800 933.003
PANEL SET
1800 600 933.004
800 933.005
2000 600 933.006
800 933.007

SEISMIC
IP65
TESTED
LIFTING- LOADING INSTRUCTIONS
SUPPORTING- LOADING INSTRUCTIONS

SEISMIC
IP65
TESTED