CONTENTS ATTACH THE SCALA RIDER AUDIO KIT TO YOUR HELMET OPTION B: USING THE GLUE PLATE POSITIONING

IT TO YOUR HELMET OPTION B: USING THE GLUE PLATE POSITIONING THE HYBRID MICROPHONE CHANGING THE MICROPHONE TYPE POSITIONING THE CORDED MICROPHONE
Glue the Audio Kit onto your helmet when the standard Back 1 Open the lining between the helmet’s inner padding.
1 2 3 4 Attach the scala rider Plate method cannot be used. Choose which of the2 glue plates Use the Velcro pad to hold the Hybrid Microphone in
Removing: Before changing
the microphone, completely
Audio Kit to your helmet is most suitable for your helmet. place. Attach the Microphone to the Velcro pad. remove the Audio Kit and
While we have no reason to believe that the gluing option 2 Adjust the location so that the microphone is located opposite the center of your mouth. backplate from the helmet. Attach Velcro to inside front of helmet
with the standard
Backplate using the might negatively affect any helmet, Cardo does not assume The Corded Microphone can be used with Full
any responsibility, irrespective of its nature and circumstances. Attaching: Replace the face helmets only (not Modular helmets).
following instructions The Glue Plate is offered as an option that you may use at your own risk and subject to renouncement of any screws to reattach the
5 future claims. backplate to the Audio Kit
Some helmets with air vents may require the mic
to be repositioned if mic audio is affected.
before reassembling on the
1 Remove the Back Plate by taking out both screws helmet and fully tightening
the screws.
Audio Kit for 6 7 2 Use the Alcohol pad to clean the exact spot on the helmet
AN ON
LY
3 Peel off protective backing sheet THIS CONE ONCE!
Qz, Q1 and Q3
OPTION A : USING THE BACK PLATE
4 Press here for 15 seconds BE D PLACING THE SPEAKERS REPLACING THE CORDED MICROPHONE SPONGE
8 9 1 Loosen both screws 5 Allow the glue to dry for 24 hours

6 Fasten both screws tightly A replacement corded microphone sponge is
2 Push the back plate between provided for future use should you need it. www.cardosystems.com
the helmet’s outer shell and
10 11 inner padding
For best clarity, place speakers directly opposite NOTE: The wires to the microphone are delicate. Avoid touching them.

3 Tighten the screws

and close to the ears. Helmets with deep recesses
may require padding to bring the speakers closer 
for ideal positioning. Optional speaker booster 1 Pinch and pull existing microphone sponge [email protected]
12 13 pads are provided for this purpose. 2 Carefully remove the existing sponge.
To use, place the speaker booster pad between the
3 Remove protective backing sheet from replacement sponge
4 Carefully attach the new sponge to the microphone

1 Noise canceling 5 Speaker Jack6 Corded 9 Alcohol pads Velcro pad in the helmet cavity and the speaker. USA & Canada: 1-800-488-0363
microphone Microphone 10 Speaker Booster 1 Attach Velcro pads to inside of Helmet. International: +49 89 450 36819
2 Hybrid mic (*Only with Q1/Q3) pads 2 Cross the long speaker wire over the center of
7 Replacement mic sponges the helmet to enhance FM radio reception.

Installation Guide
3 Release Tab 11 Velcro pads
4 Speakers 8 Allen wrench 12 Glue plates Using two speakers inside the helmet may be
prohibited in certain jurisdictions. If this is the case,

man00124 r
13 Hybrid mic clip
English - Chinese position both speakers on one side of the helmet.
 1 2 3 4 1
2

5
1
6 7 2
3
4
8 9 1 5

2 6 www.cardosystems.com
10 11 3
1
3

1 [email protected]
12 13 2
4

1 5 9 USA & Canada: 1-800-488-0363
2 7 10 International: +49 89 450 36819
3 8 11
4 12
13

man00124 r