TL084I, TL084AI, TL084BI,

TL084C, TL084AC, TL084BC

General purpose JFET quad operational amplifiers

Datasheet — production data

Features
• Wide common-mode (up to VCC+) and
differential voltage range
• Low input bias and offset current
• Output short-circuit protection P
• High input impedance JFET input stage TSSOP14
(Thin shrink small outline package)
• Internal frequency compensation
• Latch up free operation
• High slew rate: 16 V/μs (typical)

Description
D
The TL084I, TL084AI, TL084BI, TL084C,
SO-14
TL084AC and TL084BC are high-speed, JFET
(Plastic micropackage)
input, quad operational amplifiers incorporating
well matched, high voltage JFET and bipolar
transistors in a monolithic integrated circuit. Output 1 1 14 Output 4

Inverting Input 1 2 13 Inverting Input 4

The devices feature high slew rates, low input - -
+
bias and offset currents, and low offset voltage Non-inverting Input 1 3 + 12 Non-inverting Input 4

temperature coefficient. VC C + 4 11 VC C -

Non-inverting Input 2 5 + + 10 Non-inverting Input 3

Inverting Input 2 6 - - 9 Inverting Input 3

Output 2 7 8 Output 3

Pin connections
(Top view)

October 2017 DocID2301 Rev 7 1/17

This is information on a product in full production. www.st.com
Contents TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

Contents

1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4

3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Parameter measurement information . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 SO-14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Schematic diagram

1 Schematic diagram

Figure 1. Circuit schematics (for each amplifier)

VC C

N o n- inve r ting
input
I nverting
input
1 0 0Ω
2 0 0Ω
Output

1 0 0Ω
30k

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

VC C

DocID2301 Rev 7 3/17

17
Absolute maximum ratings and operating conditions TL084I, TL084AI, TL084BI, TL084C,

2 Absolute maximum ratings and operating conditions

Table 1. Absolute maximum ratings

Symbol Parameter Value Unit

VCC Supply voltage(1) ±18

Vin (2)
Input voltage ±15 V
(3)
Vid Differential input voltage ±30
Thermal resistance junction to ambient(4)(5)
Rthja TSSOP14 100 °C/W
SO-14 105
Ptot Power dissipation 680 mW
(6)
Output short-circuit duration Infinite
Operating free-air temperature range:
-40 to +125
for TL084I/TL084AI/TL084BI
Toper
Operating free-air temperature range: °C
0 to +70
for TL084C/TL084AC/TL084BC
Tstg Storage temperature range -65 to +150
HBM: human body model(7) 1000
ESD MM: machine model(8) 150 V
(9)
CDM: charged device model 1500
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the
supply voltages where the zero reference level is the midpoint between VCC+ and VCC-.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts,
whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. Short-circuits can cause excessive heating and destructive dissipation.
5. Rth are typical values.
6. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be
limited to ensure that the dissipation rating is not exceeded.
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
8. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
9. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to the ground.

Table 2. Operating conditions

Symbol Parameter TL084I/AI/BI TL084C/AC/BC Unit

VCC Supply voltage range 6 to 36 V

Toper Operating free-air temperature range -40 to +125 0 to +70 °C

4/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Electrical characteristics

3 Electrical characteristics

Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified)

TL084I/AI/AC/BI/BC TL084C
Symbol Parameter Unit
Min. Typ. Max. Min. Typ. Max.

Input offset voltage (Rs = 50 Ω)

Tamb = +25 °C TL084 3 10 3 10
Tamb = +25 °C TL084A 3 6
Vio Tamb = +25 °C TL084B 1 3 mV
Tmin ≤ Tamb ≤ Tmax TL084 13 13
Tmin ≤ Tamb ≤ Tmax TL084A 7
Tmin ≤ Tamb ≤ Tmax TL084B 5
ΔVio/ΔT Input offset voltage drift 10 10 μV/°C
Input offset current
Iio Tamb = +25 °C 5 100 5 100 pA
Tmin ≤ Tamb ≤ Tmax 4 4 nA
Input bias current(1)
Iib Tamb = +25 °C 20 200 30 200 pA
Tmin ≤ Tamb ≤ Tmax 20 20 nA
Large signal voltage gain (RL = 2 kΩ, Vo = ±10 V)
Avd Tamb = +25 °C 50 200 25 200 V/mV
Tmin ≤ Tamb ≤ Tmax 25 15
Supply voltage rejection ratio (RS = 50 Ω)
SVR Tamb = +25 °C 80 86 70 86 dB
Tmin ≤ Tamb ≤ Tmax 80 70
Supply current, no load
ICC Tamb = +25 °C 1.4 2.5 1.4 2.5 mA
Tmin ≤ Tamb ≤ Tmax 2.5 2.5
±11 +15 ±11 +15
Vicm Input common mode voltage range V
-12 -12
Common mode rejection ratio (RS = 50 Ω)
CMR Tamb = +25 °C 80 86 70 86 dB
Tmin ≤ Tamb ≤ Tmax 80 70
Output short-circuit current
Ios Tamb = +25 °C 10 40 60 10 40 60 mA
Tmin ≤ Tamb ≤ Tmax 10 60 10 60
Output voltage swing
Tamb = +25 °C RL = 2 kΩ 10 12 10 12
±Vopp RL = 10 kΩ 12 13.5 12 13.5 V
Tmin ≤ Tamb ≤ Tmax RL = 2 kΩ 10 10
RL = 10 kΩ 12 12
Slew rate
SR 8 16 8 16 V/μs
Vin = 10 V, RL = 2 kΩ, CL = 100 pF, unity gain

DocID2301 Rev 7 5/17

17
Electrical characteristics TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued)

TL084I/AI/AC/BI/BC TL084C
Symbol Parameter Unit
Min. Typ. Max. Min. Typ. Max.

Rise time
tr 0.1 0.1 μs
Vin = 20 mV, RL = 2 kΩ, CL = 100 pF, unity gain
Overshoot
Kov 10 10 %
Vin = 20 mV, RL = 2 kΩ, CL = 100 pF, unity gain
Gain bandwidth product
GBP 2.5 4 2.5 4 MHz
Vin = 10 mV, RL = 2 kΩ, CL = 100 pF, F= 100 kHz
Ri Input resistance 1012 1012 Ω
Total harmonic distortion
THD F= 1 kHz, RL = 2 kΩ,CL = 100 pF, Av = 20 dB, 0.01 0.01 %
Vo = 2 Vpp)
Equivalent input noise voltage nV
en 15 15 ------------
RS = 100 Ω, F= 1 kHz Hz

∅m Phase margin 45 45 degrees

Channel separation
Vo1/Vo2 120 120 dB
Av = 100
1. The input bias currents are junction leakage currents which approximately double for every 10°C increase in the junction
temperature.

6/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Electrical characteristics

Figure 2. Maximum peak-to-peak output voltage Figure 3. Maximum peak-to-peak output voltage
vs. frequency (RL = 2 kΩ) vs. frequency (RL = 10 kΩ)

Figure 4. Maximum peak-to-peak output voltage Figure 5. Maximum peak-to-peak output voltage
vs. frequency and temp. vs. free air temp.

Figure 6. Maximum peak-to-peak output voltage Figure 7. Maximum peak-to-peak output voltage
vs. load resistance vs. supply voltage

30
MAXIMUM PE AK-T O -PE AK OUTPUT

R L = 10 kΩ
25
Tamb = +25˚C
20
VOLT AG E (V)

15

10

0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE ( V )

DocID2301 Rev 7 7/17

17
Electrical characteristics TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

Figure 8. Input bias current vs. free air Figure 9. Large signal differential voltage
temp. amplification vs. free air temp.

100 1000
VCC = 15V 400
INPUT BIAS C UR R E NT (nA)

200

AMPLIFICATION (V/mV)
10

DIFFERENTIAL VOLTAGE
100

1 40
20
10 V CC = 15V
0.1 V O = 10V
4
2 R L = 2k Ω
0.01 1
-50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C ) TEMPERATURE (˚C)

Figure 10. Large signal differential voltage Figure 11. Total power dissipation vs. free air
amplification and phase shift vs. frequency temp.

250
(V/mV)

225 V C C = 15V
TOTAL P OW E R DIS S IP AT ION (mW )

200 No signal
175 No load
150
125
100
75
50
25
0
-75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C )

Figure 12. Supply current per amplifier vs. free Figure 13. Supply current per amplifier vs.
air temp. supply voltage

2.0 2.0
S UPPLY C UR R E NT (mA)

1.8 V C C = 15V 1.8 T a mb = +25˚C

1.6 No signal 1.6 No signal
S UP PL Y C UR R E NT (mA)

1.4 No load 1.4 No load

1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
0.4 0.4
0.2 0.2
0 0
-75 -50 -25 0 25 50 75 100 125 2 4 6 8 10 12 14 16
TEMPERATURE (˚C ) SUPPLY VOLTAGE ( V )

8/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Electrical characteristics

Figure 14. Common mode rejection ratio vs. Figure 15. Voltage follower large signal pulse
free air temp. response

89
R L = 1 0 kΩ
C OMMON MODE MODE R E JE C T ION

88
V C C = 1 5V
87
R ATIO (dB)

86

85

84

83
-75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C )

Figure 16. Output voltage vs. elapsed time Figure 17. Equivalent input noise voltage vs.
frequency

28 70
24 V C C = 15V
60
OVERSHOOT A V = 10
OUT P UT VOLT AGE (mV)

E QUIVALE NT INP UT NOIS E

20 90% 50 R S = 100 Ω
VOLT AG E (nV/VHz)

16 T amb = +25˚C
40
12
30
8
V C C = 15V
20
4 R L = 2k Ω
10%
0 Tamb = +25˚C 10
tr
-4 0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 10 40 100 400 1k 4k 10k 40k 100k
TIME ( μs ) FREQUENCY (Hz)

Figure 18. Total harmonic distortion vs.

frequency

1
V VC C = = 15V 15V
T OTAL HAR MONIC DIS TOR T ION

C
0.4
A AV V= =1 1
V VO O(rms) = =6V6V
(rms)
0.1
T amb
T amb= =+25˚
+25˚CC
0.04
(%)

0.01
0.004

0.001
100 400 1k 4k 10k 40k 100k
FREQUENCY (Hz)

DocID2301 Rev 7 9/17

17
Parameter measurement information TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

4 Parameter measurement information

Figure 19. Voltage follower Figure 20. Gain-of-10 inverting amplifier

10k Ω
1k Ω
eI -
1/4
T L084 eo

RL C L = 100pF

10/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Typical applications

5 Typical applications

Figure 21. Audio distribution amplifier

fO = 1 00 kH z

-
1 /4
T L 0 84 Output A
1M Ω

-
1 /4 -
1 μF T L 0 84
1 /4
Input T L084 Output B

100k Ω 100k Ω
100k Ω
V C C+
1OO μF -
100k Ω 1 /4
T L 0 84 Output C

Figure 22. Positive feeback bandpass filter

16k Ω 16k Ω

2 2 0 pF 2 2 0 pF

43k Ω 43 k Ω
43k Ω 30k Ω 43k Ω 30k Ω
Input - -
2 2 0 pF 1/4 1/4 43k Ω
- 2 2 0 pF -
T L 084 T L 084
43 k Ω 1/4 1/4
T L 084 T L 084
Output B
1 .5 k Ω 1 .5 k Ω

Ground
Output A

DocID2301 Rev 7 11/17

17
Typical applications TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

Figure 23. Output A Figure 24. Output B

Second order bandpass filter Cascaded bandpass filter

fo = 100 kHz; Q = 30; Gain = 4 fo = 100 kHz; Q = 69; Gain = 16

12/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Package information

6 Package information

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

6.1 TSSOP14 package information

Figure 25. TSSOP14 package mechanical drawing

A A2
K L
A1 b e c E

E1

PIN 1 IDENTIFICATION
1

Table 4. TSSOP14 package mechanical data

Millimeters Inches
Ref.
Min. Typ. Max. Min. Typ. Max.

A 1.2 0.047
A1 0.05 0.15 0.002 0.004 0.006
A2 0.8 1 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.012
c 0.09 0.20 0.004 0.0089
D 4.9 5 5.1 0.193 0.197 0.201
E 6.2 6.4 6.6 0.244 0.252 0.260
E1 4.3 4.4 4.48 0.169 0.173 0.176
e 0.65 BSC 0.0256 BSC
K 0° 8° 0° 8°
L1 0.45 0.60 0.75 0.018 0.024 0.030

DocID2301 Rev 7 13/17

17
Package information TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

6.2 SO-14 package information

Figure 26. SO-14 package mechanical drawing

Table 5. SO-14 package mechanical data

Dimensions

Millimeters Inches
Ref.
Min. Typ. Max. Min. Typ. Max.

A 1.35 1.75 0.05 0.068

A1 0.10 0.25 0.004 0.009
A2 1.10 1.65 0.04 0.06
B 0.33 0.51 0.01 0.02
C 0.19 0.25 0.007 0.009
D 8.55 8.75 0.33 0.34
E 3.80 4.0 0.15 0.15
e 1.27 0.05
H 5.80 6.20 0.22 0.24
h 0.25 0.50 0.009 0.02
L 0.40 1.27 0.015 0.05
k 8° (max.)
ddd 0.10 0.004

14/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC Ordering information

7 Ordering information

Table 6. Order codes

Order code Temperature range Package Packing Marking

TL084IDT 084I
TL084AIDT -40°, +125° SO-14 084AI
TL084BIDT 084BI
TL084IYDT(1) -40°, +125° 084IY
SO-14
TL084BIYDT(1) Automotive grade 084BIY
Tape & reel
TL084IPT -40°, +125° TSSOP14 084I
TL084CDT 084C
TL084ACDT SO-14 084AC
0°, +70°
TL084BCDT 084BC
TL084CPT TSSOP14 084C
TL084CD 0°, +70° SO-14 Tube 084C
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening
according to AEC Q001 & Q002 or equivalent.

DocID2301 Rev 7 15/17

17
Revision history TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

8 Revision history

Table 7. Document revision history

Date Revision Changes

28-Mar-2001 1 Initial release.

Added values for Rthja, Rthjc and ESD in Table 1: Absolute maximum
ratings.
30-Jul-2007 2 Added Table 2: Operating conditions.
Expanded Table 6: Order codes.
Template update.
Removed information concerning military temperature ranges
15-Jul-2008 3 (TL084Mx, TL084AMx, TL084BMx).
Added automotive grade order codes in Table 6: Order codes.
Removed commercial types TL084IYD, TL084AIYD and
05-Jul-2012 4 TL084BIYD.
Updated Table 6: Order codes.
Added part numbers TL084A and TL084B.
Added SO-14 package silhouette.
Updated layout of Table 1: Absolute maximum ratings.
Updated of Table 3: VCC = ±15 V, Tamb = +25 °C (unless otherwise
29-Jan-2013 5 specified).
Replaced SO-14 package mechanical drawing (Figure 27: SO-14
package mechanical drawing).
Replaced SO-14 package mechanical data (Table 5: SO-14 package
mechanical data).
Replaced 105 °C by 125 °C in Table 1: Absolute maximum ratings
and Table 2: Operating conditions.
11-Jul-2017 6
Removed DIP14 package information.
Updated Table 6: Order codes to remove obsolete part numbers.
17-Oct-2017 7 Updated part numbers in the title, and in Table 6: Order codes.

16/17 DocID2301 Rev 7

TL084I, TL084AI, TL084BI, TL084C, TL084AC, TL084BC

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2017 STMicroelectronics – All rights reserved

DocID2301 Rev 7 17/17

17