Physical Parameters

Display LCD
Communication RS485
Operating Temperature Range -40°C~60°C
DDSU666 Single phase electronic Ambient Humidity 0-95% Non-condensing
energy meter user manual Ingress Protection IP54
Installation method mounting rack
Dimensions[H*W*D][mm] 98*36*65
1.Overview of products Weight [kg] 0.2
1.1 Applicable range Applicable Standard CE, RoHS
The DDSU666 meter mainly applied
into the measurement and display for
3.Instructions for installation
the photovoltaic system parameters in 3.1 Check the Package
the electric circuit including voltage, Check whether the product shell in the carton is damaged, if is,
current, power, frequency, power please contact the supplier
factor, active energy, etc. The network
can be realized through RS485 3.2 Installation
communication interface and external Directly clip the instrument on the rail and
device. Adopting the standard install it on the distribution box.
(1)When installing, firstly clip one
DIN35mm din rail mounting and
terminal of the slot and then clip to the
modular design, it is characterized
rail with power. (standard DIN35mm)
with small volume, easy installation (2)When disassembling, press the
and easy networking. movable card with a screwdriver and take
out the instrument.
1.Overview of products Figure 3.1 Meter installation
1.2 Specification for product model
3.3 Instruction of wiring terminal

1.3 Outline & Mounting Dimension

Figure 3.2 Direct connection

Figure 1.1 Configuration

2.Datasheet
Type DDSU666
Electrical Characteristics
Application Single phase
Nominal Voltage[V] 220,230,240 Figure 3.3 Meter connection diagram

Operating range 0.7~1.2Un

Max. Current [A] 80
Frequency/Range [Hz] 50,60/±5
Power Consumption[W] ≤1
Max. Instant Consumption [VA] ≤5
 LCD is current
The unit of the active power, the display data of
3.4 RS485 interface of inverter W
indicating LCD is active power
The unit of the reactive power, the display data of
var
indicating LCD is reactive power
The unit of the frequency, the display data of
Hz
indicating LCD is frequency
The unit of the active energy, the display data of
kWh
indicating LCD is active energy

6.Export limitation function setting

The steps for matching R5 series inverters are as follows:
Figure 3.4 RS485 pin (1)Download eSolar O&M APP
Web to eSolar website https://fop.saj-electric.com to scan the QR
code and download “eSolar O&M” APP (or download it from
PinNumber Description Effect
Google Play or App Store by searching “eSolar O&M”). After the
1 NC
installation on your phone, please login it with your installer account.
2 GND_W Ground wire
3 +7V_W Power supply
4 NC (2)Log in APP→ Click “My” → Click “Remote control” → Click
5 NC “WiFi” /“Bluetooth”→ Click “Next step”. as shown in Figure6.1.
6 NC Please refer to WiFi/GPRS/4G module manual for detailed
7 RS485-A Transmission RS485 connection operation.
8 RS485-B differential signal
Table 3.1 RS485 pin port definition (3)Enter “local connect” page and select “Export limitation setting”
→ input password：201561 as shown in Figure6.2.
4.Fault and troubleshooting

Fault Analysis of Troubleshooting Remark

phenomenon causes
Check if the actual
connection is the same
as the requirement of
The wiring
may not the wiring diagram.
connected Pay special attention to While
Display fault according to “N” position of the checking the
the wiring voltage, the high & low
connection, be
diagram of end of the current and
the meter sure the meter
terminal labeling are
is in the state Figure 6.1 Local connect Figure 6.2 Export limitation setting
different from actual
of
number.
disconnection,
Check if the
guarantee the (4)Turn on “export limitation”, Wait for 15s countdown seconds to
The communication setting
communicati safety of set successfully，supply the power mode and current mode，as shown
information such as
on setting communication human life.
Communicati in Figure6.3 and Figure6.4
on fault information
address, baud rate,
of the meter
may be verification mode is the
incorrect same as the PC
settings.

5.Displayed functions

When the energy meter is in normal working condition (on load

state), the positive pulse indicator should be flashed. If long time for
no flashing or light for the indicator, please check whether the wiring
mode of the energy meter is right or not.

Figure6.3 Countdown interface Figure6.4 Power limit/Current limit setting

Note:
Table 5.1 LCD logo meanings 1.Power mode and current mode could be alternatively selected;
Symbol Meaning 2.The setting parameter cannot exceed the given range value
The unit of the voltage, the display data of indicating
V 3.When the setting is completed, the export limitation system will
LCD is voltage
A The unit of the current, the display data of indicating begin to run.