M-73 & M-88

Compasses
Nothing else measures up!
Follow us!
York Survey Supply Centre
@York_Survey
@York_Survey

Prospect House
George Cayley Drive
Clifton Moor
York
England
YO30 4XE Code: 36020, 36022

Tel: +44 (0) 1904 692723

Fax: +44 (0) 1904 690385

E-Mail: [email protected]
Operating
Instructions
...for secure online ordering of all our products!

Ref:.. \operat98\instructions 19\36020.qxp 07-01-19 ©York Survey Supply Centre 2019

 M-73 & M-88 Compass Taking Bearings from a Map
Note: This procedure gives a True bearing, which may need to be converted to Magnetic before using it for other purposes.
This prismatic compass is built to full military specifications. It will operate with precision accuracy to within half a degree, in (a) Lay your map on a level, flat surface, and use the sight line axis of the compass to help you position the map so that it’s grid
temperatures from 55ºC (131ºF) down to -30ºC (-22ºF) for the M-73, and -20ºC (-4ºF) for the M-88. It is shock resistant, and lines lie correctly North & South.
built to withstand the roughest and toughest conditions you are likely to encounter anywhere in the world. (b) Draw a line on the map from your present position to the object or point that is your objective.
(c) Place the compass down on the map on the line you have drawn (with the sighting prism nearest to your present position).
Lid tab Open the lid fully so that it lies flat on the map, then align the axis of the compass in line with the line you’ve already drawn to
your objective.
(d) Slacken the bezel clamp (M-73 only) to allow free movement of the bezel. Rotate the bezel until it’s luminous mark
Window coincides with the luminous North pointer marked on the compass card. Re-tighten the bezel clamp to lock the bezel if you
sight line wish.
(e) Close to the hinge, you will see an ‘index line’ marked on a luminous patch under the bezel glass. The bezel glass itself is
marked in graduations. Read off the bearing on the bezel glass that is now directly over this index line. This figure is the re-
quired bearing of the target object from your present position - or the direction in which you wish to travel.
Index line
To Follow a Heading
Bezel
Bezel glass
luminous mark
Note: For this exercise, the bearing of the course you are going to follow must be converted to Magnetic before being applied to
the compass bezel. In the case of a bearing worked out from a map, that will mean making a slight adjustment to the bezel as
explained under ‘Magnetic and True Bearings’ (see below).
Sighting prism
Bezel clamp
Prism slide Compass card
Thumb ring
luminous mark Given a direction that you wish to travel, whether it is supplied to you or one that you have calculated from a map as explained,
you can see that course on the compass bezel and use the compass to guide you in the right direction.
(1) First set the bezel for the direction you wish to travel, either from a map as already described or in the case of a known
bearing (which must be Magnetic) simply turn the bezel until the graduation on the bezel corresponding to that bearing
coincides with the index line. Before proceeding, tighten the bezel clamp to lock the bezel if you wish.
Preparing the Compass for Use (2) To travel in the desired direction, open the lid right back and hold the compass so that the luminous marks on the bezel and
When using the compass, always keep it level to avoid inaccuracies. Ensure that any ferrous metal objects, such as a watch, the compass card are directly over one another. The axis of the compass is then the direction in which you should
knife, etc., are kept well away from the compass, otherwise they too will cause errors. proceed. You can close the compass lid if you wish; you will still be able to see the two luminous marks and keep them in line.
(3) From time to time, check your course more accurately by viewing through the sighting prism to confirm that you are still
(a) Open the lid until it stands up at right angles to the main body of the compass. following the correct bearing.
(b) Turn the sighting prism fully over, to the limit of it’s movement so that the sighting slit is on top of the prism.
(c) To adjust the sighting prism focus your eyesight, hold the body of the compass in one hand and look through the sighting Applying Known Bearings to a Map
prism at the compass card graduations. With your free thumb, push up at the base of the prism mount to raise the prism in it’s Note: Before carrying out the following procedure to apply bearings to a map, their values must be converted to True.
slide; continue raising it until you see the compass card numerals in focus through the prism (this slide is purposely stiff to A known bearing, or a bearing that you yourself have taken by sighting an object, can be transferred onto a map using a
prevent it moving inadvertently when the compass is in normal use). procedure that is almost exactly the reverse of that described for taking bearings from a map.
(a) First, set the known bearing by turning the compass bezel until the graduation on the bezel corresponding to that bearing
Correct Method of Sighting coincides with the index line.
(b) Lay the map on a level surface and orientate it correctly North and South as described under ‘taking bearings from a map’.
(c) Open the lid of the compass fully. Keeping the two luminous marks directly over one another, place the compass down on
the map with the prism end over your present position.
(d) The sight line axis of the compass then indicates the direction of the map which corresponds to the known bearing you
began with.

Using the Compass at Night

The compass contains Tritium light sources to enable it to be used in complete darkness without the aid of artificial light.
When travelling at night, it can be very difficult to follow a compass course accurately without a lot of practice. However, it is
often possible to distinguish objects and features of the landscape at some distance, particularly against the skyline. In such cir-
cumstances, the easiest way to maintain a straight course is to pick out an object on the required bearing, and advance directly
towards it. When you reach it, pick out another object, and so on.
When sighting through the prism at night, the sight line on the lid window will almost certainly not be visible. The lid should
*GRADUATIONS IN MILS
therefore be laid back almost to the horizontal, which will reveal a luminous marker on the underside of the lid tab which can be
If your compass is graduated
in mils rather than degrees, used as a sight line instead.
each graduation represents
approximately 20 mils. Magnetic and True Readings
In most parts of the world, there are a few degrees difference between the position of the geographical North Pole and that of
the Magnetic North Pole. This is known as Magnetic Variation. In all workings with a compass it must be taken into account.
Taking Bearings on Distant Objects A True bearing must always be converted to Magnetic before setting it on your compass. Magnetic bearings taken with the
Note: this procedure gives a Magnetic bearing, which may need to be converted to a True bearing before using it for other pur- compass must always be converted to True before applying them to a map.
poses. To convert a True bearing to Magnetic, the number of degrees Variation should be subtracted if the Variation is to the East, and
(a) The correct way to hold the compass for taking bearings is with your thumb through the large metal ring and the base of the added if it is to the West.
compass resting on top of your closed fist. If converting from Magnetic to True, then obviously these adjustments should be made in the opposite directions.
(b) Hold the compass level, about 2 inches (50mm) from your eye. Sight through the prism, and line up the object on which you
are taking the bearing with the prism slit and the sight line marked on the lid window.
(c) Allow the card to settle. Still looking through the prism, you will see that the sight line on the lid window appears
superimpose on the graduations visible on the outer ring of the compass card. Whichever graduation mark lines up with the
sight line on the lid window, that is the bearing you require. Each graduation on this outer ring represents one degree*.
Ref:.. \operat98\instructions 19\36020.qxp 07-01-19 ©York Survey Supply Centre 2019