Scribd
Upload
110 views1 page

Crafco Roadsaver 522 PDS Sept 2016

Uploaded by

jorge silva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
110 views1 page

Crafco Roadsaver 522 PDS Sept 2016

Uploaded by

jorge silva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

PRODUCT DATA SHEET

ROADSAVER 522
PART NO. 34522
SEPTEMBER 2016
6165 W Detroit St. • Chandler AZ 85226
+1 (602) 276-0406 • +1 (800) 528-8242 • FAX +1 (480) 961-0513
www.crafco.com
READ BEFORE USING THIS PRODUCT

GENERAL Crafco RoadSaver 522 sealant is a hot-applied asphalt based product used to seal and fill cracks and joints in both asphalt and
Portland cement concrete pavements in cold to very cold climates. RoadSaver 522 is supplied in solid form which when melted and properly
applied forms an adhesive flexible compound with high elongation and low stress development at low temperatures, while resisting flow during
the summer. RoadSaver 522 can be used in highway, street, and airfield pavements and is applied using either pressure feed melter
applicators or pour pots. At application temperature, RoadSaver 522 is a free flowing, self-leveling product. RoadSaver 522 was developed
specifically to perform in temperature extremes and movement conditions that exist in the coldest climates. Over the last 20 years, RoadSaver
522 has proven to be one of the best, if not the best performing crack sealant for very cold climates. Several states and Canadian provinces
have adopted specification based on the exceptional performance of RoadSaver 522. Due to the softness of the product RoadSaver 522 is not
recommended for use as crack sealant or filler in parking lots or other areas with high foot traffic. VOC = 0 g/l.

USAGE GUIDELINES Roadsaver 522 is applicable


for Sealant/ Reservoir or Filler/Overband use in cold to very High Temperature (°C) High Temperature (°C)
cold climates with low and high pavement temperatures
°C 52 58 64 70 76 82 °C 52 58 64 70 76 82

Low Temperature (°C)


identified in the charts. Pavement temperatures for the

Low Temperature (°C)


project location are determined at 98% reliability using -10 -10
FHWA LTPPBind V3.1, and sealant or filler use is -16 -16
determined following Crafco Product Selection Procedures. -22 -22
-28 -28
-34 -34
-40 -40
-46 -46
Applicable Pavement Temperatures
Sealant / Reservoir Use Filler / Overband Use

SPECIFICATION CONFORMANCE RoadSaver 522 meets requirements of several Agency specifications for low modulus
sealant including Minnesota, Montana, and Manitoba as follows:

Test Spec. Limits


Cone Penetration, 77°F (25°C) (ASTM D5329) 100-150
Cone Penetration, 0°F (-18°C) (ASTM D5329 modified) 25 min.
Flow, 140°F (60°C), 5h (ASTM D5329) 10 mm max.
Resilience (ASTM D5329) 30-60%
Bond, -20°F (-29°C), 200% ext. (1/2" (12.7mm) thick specimen (ASTM D5329) Pass 3 cycles
Asphalt Compatibility (ASTM D5329) Pass
Recommended Application Temperature 380°F (193°C)
Maximum Heating Temperature 400°F (204°C)

APPLICATION The unit weight of Crafco RoadSaver 522 is 10.0 lb. per gallon (1.20 kg/L) at 60°F (15.5°C). Prior to use, the user must
read and follow Installation Instructions for Hot-Applied RoadSaver, PolyFlex, Parking Lot and Asphalt Rubber Products to verify proper
product selection, heating methods, pavement preparation procedures, application geometry, usage precautions and safety procedures.
These instructions are provided with each pallet of product.

PACKAGING Product is supplied in either cardboard boxes, or in meltable, boxless PLEXI-melt packaging. Both package types are
labeled in accordance with OSHA, GHS, and specification requirements; are sold by net weight; are interlock stacked on 48 x 40 in. (122 x102
cm) 4-way pallets; can be stored outside; and are covered with a weather resistant pallet cover and 2 layers of UV protected stretch wrap.
o BOX packaging consists of cardboard boxes containing approximately 30 lb. (13.6 kg) of product with 75 boxes per pallet, weighing
approximately 2250 lb. (1020 kg). Boxes contain a quick melting release film for easy removal and are taped closed, without any staples.
o PLEXI-melt packaging consists of 30 lb. (13.6 kg) blocks of product with 70 packages per pallet, weighing 2100 lb. (952 kg). To use, the
pallet wrap is removed, and individual blocks are placed in the melter. There are no cardboard boxes or other cardboard components to
open, empty, handle, or dispose of. PLEXI-melt packaging quickly melts into the product without affecting specification conformance.

WARRANTY CRAFCO, Inc. warrants that CRAFCO products meet applicable ASTM, AASHTO, Federal or State specifications at time
of shipment. Techniques used for the preparation of the cracks and joints prior to sealing or filling are beyond our control as are the use and
application of the products; therefore, Crafco shall not be responsible for improperly applied or misused products. Remedies against Crafco,
Inc., as agreed to by Crafco, are limited to replacing nonconforming product or refund (full or partial) of purchase price from Crafco, Inc. All
claims for breach of this warranty must be made within three (3) months of the date of use or twelve (12) months from the date of delivery by
Crafco, Inc. whichever is earlier. There shall be no other warranties expressed or implied. For optimum performance, follow Crafco
recommendations for product installation.

©2016, Crafco, Inc., #A1138

You might also like