Scribd
Upload
103 views

X-Roc Multibond LX: Multi-Purpose Primer and Mortar Additive

X-Roc MultiBond LX is a multi-purpose liquid polymer additive that improves the adhesion, water resistance, and performance of cement-based mortars and renders. It can be used for water resistant renders and screeds, bonding mortars and screeds, and repairing and patching concrete. When added to mixes, it improves workability and mechanical properties. The product is supplied as a white liquid and has a shelf life of 12 months when stored properly.

Uploaded by

Amr Ragab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
103 views

X-Roc Multibond LX: Multi-Purpose Primer and Mortar Additive

X-Roc MultiBond LX is a multi-purpose liquid polymer additive that improves the adhesion, water resistance, and performance of cement-based mortars and renders. It can be used for water resistant renders and screeds, bonding mortars and screeds, and repairing and patching concrete. When added to mixes, it improves workability and mechanical properties. The product is supplied as a white liquid and has a shelf life of 12 months when stored properly.

Uploaded by

Amr Ragab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technical Datasheet

X-Roc MultiBond LX
Multi-purpose primer and mortar additive.

Product Description Laboratory Test Data


X-Roc MultiBond LX is a multi-purpose polymer used to Property Typical Results
improve adhesion and water resistance of cement based
Nature Liquid
mortar and renders.
Color White
Specific gravity 1.003 ± 0.002
Advantages Chloride content Nil
• Easy to use.
• Multi-function.
Specification Compliance
• Improves mortars and screeds.
1- ASTM C1059 Type II
• Can be used in immersed conditions.
2- BS 6319 part 4
Uses
• Water resistant renders and screeds. Packaging
• Bonding of mortars and screeds. X-Roc MultiBond LX is supplied in 1 kg, 4 kg, 20kg and 200kg
• Repair and patching of concrete.
Shelf Life
Mix Designs 12 months when stored below 95°F(35°C) under shade in a
The mix design below are for general guidance only. Due dry environment.
to the variability in cement, aggregates, sand, mix design
and properties will vary. Installation Guidelines
General Purpose Render, mortar or Screed Surface Preparation
50 kg Type 1 Portland cement
All surfaces must be clean and structurally sound. Oil and
150 kg Washed sharp sand (medium grading) grease must be removed. For best results, the surface of the
11 liters X-Roc MultiBond LX concrete should be mechanically scarified or scrabbled,
11 liters Water although other methods, including grit blasting, hydro
Yield 130 liters blasting and acid etching can be used.

Heavy Duty Floor Screed (Min. Thickness 15mm) Mixing


50kg Type 1 Portland cement Using an NCC X-Calibur approved forced action mechanical
90kg 3 to 5mm hard aggregate such as granite mixer, add the cement and aggregates and mix for one
90kg Washed sharp sand (medium grading) minute. Continue mixing and add X-Roc MultiBond LX , pre-
10 liters X-Roc MultiBond LX dispersed in the mixing water, and mix for at least a further
20 liters Water (approximate)
three minutes until fully mixed.
Yield 120 liters (approximate)

Mortars
Concrete repair mortar
Thickness is dependent on application but 15mm is normal.
50kg Type 1 Portland cement
On vertical surfaces this is built up in two applications.
125 kg Washed sharp sand (medium grading)
24 liters X-Roc MultiBond LX
Normal time between applications is 5 hours but this is
Yield 90 liters (approximate)
dependent on temperature.
Where more than one coat is applied ensure that the
Fairing coat intermediate coats are cross hatched to provide a mechanical
50kg Type 1 Portland cement key. If the surface dries out completely then the surface
100 kg Fine sand should be re-primed.
23 liters X-Roc MultiBond LX
Yield 80 liters (approximate)

Edition 4.2018
Version 1.2013
Renders Datasheet Validity
Two priming coats should be applied ideally at right NCC X-Calibur makes modifications to its product
angles to one another. The second coat should be applied datasheets on a continuous basis. Please check the
immediately after the first coat has dried, approximately datasheet update section on www.ncc.com.eg to ensure
30 minutes. Apply general purpose mortar while the you have the latest version.
primer is still tacky. Minimum thickness is 10mm. Where
more than one layer is applied, ensure that the Warranties
intermediate layers are hatched to provide a mechanical NCC X-Calibur supplies products that comply with the
key. If the surface dries out completely then the surface properties shown on the current datasheets. In the unlikely
should be re-primed. Allow 5 hours between layers. event that products supplied are proved not to comply with
these properties, then we will replace the non-compliant
Screeds product or refund the purchase price.
Apply up to 75mm in one application; the minimum NCC X-Calibur does not warrant or guarantee the
screed thickness should be 25mm. Ensure that the screed installation of the products as it does not have control over
is well bonded to the substrate and that it is fully the installation or end use of the products. Any suspected
compacted. Do not use water to finish the surface as this defects must be reported to X-Calibur in writing within five
will cause cracking, crazing and dusting of the surface. working days of being detected. NCC X-Calibur Construction
Chemistry Inc. makes no warranty as to
Curing merchantability or fitness for a particular purpose
Cure for a minimum of three days using a curing and this warranty is in lieu of all other warranties
compound or water. The longer the curing period (up to express or implied. NCC X-Calibur Construction Chemistry
seven days) the better will be the performance of the Inc. shall not be liable for damages of any sort including
mortar. Screeds should be continuously water cured for
remote or consequential damages, down time, or delay.
seven days.

Limitations
Do not allow to dry before applying mortar (when being
used as a primer).
Do not discard into the water system.
Avoid excessive application,
Avoid skin contact,

Health and Safety


This product is for industrial use only by
trained operatives. It is potentially hazardous
if not used correctly. Please refer to the
Material Safety Data Sheet (MSDS) prior to
the purchase and use of this product. The
MSDS can be obtained via our website
www.ncc.com.

Authorized Technical Specialist


Please note that only X-Calibur Authorized Technical
Specialists ('ATSs') are permitted to change any of the
information in this data sheet or to provide written
recommendations concerning the use of this product. Visit
www.ncc.com.eg for a full list of X-Calibur ATSs.

Quality Statement
All Products manufactured by NCC X-CALIBUR or imported from X-CALIBUR companies world-wide are
manufactured to procedures certified to conform the quality, environment, systems described in the
ISO 14001:2004. ISO 9001:2000.

Hotline: 16960 E-mail: [email protected] Website: www.ncc.com.eg www.x-calibur.us

You might also like