330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...

Página 1 de 7

Cerrar SIS

Pantalla anterior

Producto: EXCAVATOR
Modelo: 330B L EXCAVATOR 6DR
Configuración: 330B L Excavator 6DR00001-UP (MACHINE) POWERED BY
3306 Engine

Pruebas y Ajustes
308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B
Excavators Engine and Pump Control
Número de medio -RENR1998-06 Fecha de publicación -01/10/2004 Fecha de actualización -06/10/2004

i01256784

Parameter - Adjust
SMCS - 1931-025-NQ

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 2 de 7

Illustration 1 g00662996
Monitor Panel

Hydraulic Oil Type

Service code 80 allows you to select the type of oil that is being used. This automatically determines
the alert values that are used for the oil level and temperature.

1. Enter service code 80.

The character display identifies the type of oil that has been selected. Mineral oil or biological
oil may be selected.

2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the third position from the right.

3. Depress the boom priority mode switch (23) in order to select the mineral oil. "Std" "80Std".

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 3 de 7

4. Depress the swing priority mode switch (24) in order to select the biological oil. "b10"
"80b1o".

5. Set the type of oil.

a. Depress travel alarm cancel switch (22) in order to set the new value.

When the new value is set, the position of the blinking character does not change. The
service code will flash.

Automatic Engine Control (AEC) (Engine Speed)

When minimum hydraulic load exists and the AEC is active, engine speed is reduced. Service code
81 sets the engine speed that is used by the AEC.

1. Enter service code 81.

2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the fourth position from the right.

3. Depress boom priority mode switch (23) in order to INCREASE the speed setting by 10 RPM.

The speed setting can be set at any speed that is between 800 RPM and high idle.

4. Depress swing priority mode switch (24) in order to DECREASE the speed setting by 10
RPM.

The speed setting can be set at any speed that is between 800 RPM and high idle.

5. Set the new value for the AEC.

a. Depress travel alarm cancel switch (22) in order to set the new values.

When the new value is set, the position of the blinking character does not change. The
service code flashes.

Automatic Engine Control (AEC) (Activation Time Delay)

When minimum hydraulic load exists and the AEC is active, engine speed is reduced. Service code
82 sets the time delay that is used by the AEC.

1. Enter service code 82.

The character display indicates the current time delay in 0.1 second.

2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the second position from the right.

3. Depress boom priority mode switch (23) in order to INCREASE the setting of the time delay
by 0.5 second.

The time delay can be set from 0 to 20 seconds.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 4 de 7

4. Depress swing priority mode switch (24) in order to DECREASE the setting of the time delay
by 0.5 second.

The time delay can be set from 0 to 20 seconds.

5. Set the new value for the AEC.

a. Depress travel alarm cancel switch (22) in order to set the new values.

When the new value is set, the position of the blinking character does not change. The
service code flashes.

Automatic Engine Control (AEC) (Memory Mode)

An activation delay of three seconds is the standard for the AEC. Service code 83 is used to input
changes from the standard time delay. The changes are stored in the controller memory.

When the machine is secured, the machine automatically defaults to the work mode and the power
mode. Also, the travel speed automatically defaults to the LOW speed position. This is accomplished
regardless of the state of the memory mode.

1. Enter service code 83.

The memory mode may be turned "ON" or turned "OFF". Display (1) indicates the state of the
memory mode. The mode can be "on" or "oF".

2. Depress fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the position on the right.

3. Depress boom priority mode switch (23) in order to turn the mode "ON". "83on".

The mode can be "on" or "oF".

4. Depress swing priority mode switch (24) in order to turn the mode "OFF". "83oF".

The mode can be "on" or "oF".

5. Set the new value for the AEC.

a. Depress travel alarm cancel switch (22) in order to set the new values.

When the new value is set, the position of the blinking character does not change. The
service code flashes.

Reduced Setting Of Horsepower (Attachment Pump)

When an attachment pump is installed on the machine, the engine will maintain the target speed.
This is done until a maximum of 30 percent of the available engine horsepower is used by the
attachment pumps. Service code 84 is used to adjust the upper limit of the main pump horsepower.

1. Enter service code 84.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 5 de 7

The character display indicates the upper limit of the main pump. The value is displayed in
percent.

2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the right two positions.

3. Depress the boom priority mode switch (23) in order to INCREASE the upper limit by 5
percent.

The upper limit can be between 0 and 100 percent.

4. Depress the swing priority mode switch (24) in order to DECREASE the upper limit by 5
percent.

The upper limit can be between 0 and 100 percent.

5. Set the new value for the AEC.

a. Depress the travel alarm cancel switch (22) in order to set the new values.

When the new value is set, the position of the blinking character does not change. The
service code flashes.

Adjustment of the Low Idle Speed

Service code 85 allows you to adjust the engine speed that is used by the low idle switch.

1. Enter service code 85.

The character display indicates the engine speed setting that is used by the low idle switch.
The value is displayed in RPM.

2. Depress the fine control mode switch (25) in order to shift the blinking character. Position the
blinking character to the right two positions.

3. Depress the boom priority mode switch (23) in order to INCREASE the speed setting by 10
RPM.

The speed setting can be between 800 RPM and high idle.

4. Depress the swing priority mode switch (24) in order to DECREASE the speed setting by 10
RPM.

The upper limit can be between 800 RPM and high idle.

5. Set the new value for the AEC.

a. Depress the travel alarm cancel switch (22) in order to set the new values.

When the new value is set, the position of the blinking character does not change. The
service code flashes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 6 de 7

Fixed Power Shift Pressure

This function allows the command signal of the power shift pressure to remain constant at a desired
pressure level. The command signal for the power shift pressure is necessary in order to perform
testing and adjusting procedures to line relief valves and procedures to perform "P-Q" tests on the
pump .

1. Enter service code 66. The character display shows the current power shift pressure in kPa.

2. Depress the fine control mode switch (25) in order to shift the blinking position of the
character display to the fourth character position from the right.

3. When the boom priority mode switch (23) is depressed, the command signal of the power shift
pressure is increased by 10 kPa (1.5 psi).

4. When the swing priority mode switch (24) is depressed, the command signal of the power shift
pressure decreases by 10 kPa (1.5 psi).

5. When the boom priority mode switch (23) and the power mode switch (19) are depressed
simultaneously, the command signal to the power shift pressure increases by 200 kPa (29 psi).

6. When the swing priority mode switch (24) and the power mode switch (19) are depressed
simultaneously, the command signal to the power shift pressure decreases by 200 kPa (29 psi).

Note: The engine speed cannot be checked with the monitor panel while you are in the mode
of fixed power shift pressure.

7. The engine speed will be displayed, if the service code 67 is entered and the power shift
pressure has been fixed by using the above procedure.

Engine Speed Change

This function changes the engine speed except the high idle and low idle engine speeds. This
function is useful for measuring the noise level.

1. Enter service code 67. The character display shows the engine speed in rpm.

2. Depress the fine control mode switch (25) in order to shift the blinking position of the
character display to the fourth position from the right.

3. When the boom priority mode switch (23) is depressed, the engine speed increases.

4. When the swing priority mode switch (24) is depressed, the engine speed decreases. The above
figure shows 1521 rpm.

5. When the boom priority mode switch (23) and the power mode switch (19) are depressed
simultaneously, the engine speed rapidly increases.

6. When the swing priority mode switch (24) and the power mode switch (19) are depressed
simultaneously, the engine speed decreases rapidly.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine(SEB... Página 7 de 7

Copyright 1993 - 2008 Caterpillar Inc. Sat Nov 22 20:36:12 EST 2008
Todos los derechos reservados.
Red privada para licenciados del SIS.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 22/11/2008