Short stroke cylinders W series Ø 12 ÷ 100 mm

The wide product range and unique design make Univer “Short stroke cylinders W series” essential for all applications
where compact overall dimensions and short strokes are required. This product, thanks to its versatility, the vast
variety of accessories, the various bore sizes combined with mechanical shock-absorbers, complies perfectly
with the requirements of the industry.

Cylinders
TECHNICAL CHARACTERISTICS

Operating pressure: 1,5 ÷ 10 bar

Ambient temperature: - 20 ÷ 80°C
Fluid: Filtered air, with or without lubrication
Construction details
Barrel profile of extruded aluminium alloy, internally and
externally anodized (15 - 18 µ).
Removable end-caps for easy inspection.
Piston fitted with permanent plastoferrite magnetic ring (upon
request; bore sizes 16 ÷ 100)
Piston seals produced in a special nitrile compound self-
compensate against wear.
Rolled stainless steel rod (AISI 303) with female thread (male
thread upon request). Codification key
Self-lubricating guide bearings.
W 100 032 0050 S M
With mechanical end stroke shock-absorbers
Magnetic switch Series DH---- or flush-mounted magnetic
sensor DF... series (Section Accessories page 2 - 3) Magnetic (upon request)
Nominal tolerance on stroke
Cyl. Tolerance Safety distance* (upon request)
Ø mm
12 ÷ 25 + 1,5/0 Stroke (mm)
32 ÷ 50 + 2/0
63 ÷ 100 + 2,5/0 Bore size (mm)
Upon request
- Rear trunnion (page 64) Cylinder type
- Nipple
- Non-rotating piston rod (bore sizes Ø 16 ÷ 100) (page 60-61) Series
- Hollow through piston rod (bore sizes Ø 20 ÷ 100)
- Magnetic option (bore sizes Ø 16 ÷ 100)
- Tandem cylinders (page 64)
CYLINDER TYPE
- Slide units, bore sizes Ø 20 ÷ 80
(Section High-Tech page 47) 100 D.A.
Double-acting cylinder
101 D.A.
Double-acting cylinder-throug piston rod
Developed forces 110 D.A.
Double-acting cylinder-non-rotating piston rod*
Calculated by applying the following formula: 111 D.A.
Double-acting cylinder-through, non-rotating
piston rod*
Thrust force Traction force 131 D.A. Double-acting cylinder- hollow through piston
Thf = S · p - a Tf = s · p - a rod (min. Ø 20 mm)

where: p = supply pressure 160 S.A. Single-acting cylinder-retracted piston rod

S = piston push surface (cm2) 170 S.A. Single-acting cylinder-extended piston rod
s = piston pull surface (cm2)
a = friction (10%) VERSION WITH REAR MALE HINGE
(except for bore size Ø 12)
Piston Max. reaction 700 D.A. Double-acting cylinder
Cyl. S s
rod Ø of the springs 760 S.A. Single-acting cylinder - retracted piston rod
Ø (cm²) (cm²)
(mm) (N) 770 S.A. Single-acting cylinder - extended piston rod
12 6 1,1 0,8 6,8 BORE
16 6 2 1,7 7,8 12 - 16 - 20 - 25 - 32 - 40 - 50 - 63 - 80 - 100 mm
20 10 3,1 2,3 13,2
STANDARD STROKE
25 10 4,9 4,1 19,6
32 12 8 6,9 35,3
Ø 12 - 25 S.A.: 5 - 10 mm
Ø 32 - 100 S.A.: 5 - 10 - 25 mm
40 16 12,6 10,6 45 Ø 12 - 16 D.A.: 5 - 10 - 20 - 25 - 30 - 40 - 50 mm
50 16 19,6 17,6 70,5 Ø 20 - 100 D.A.: 5 - 10 - 20 - 25 - 30 - 40 - 50 - 75 mm
63 20 31,1 28 96 * The cylinder types without safety distance requested by the
80 25 50,3 54,3 119,5 customer have to be installed by the user in accordance with
EC rules EN 294 (page 90-91).
100 25 78,5 73,6 237,2

55-I
 Double-acting cylinder

Double-acting cylinder W 100 . . / W 100 . . M Series

Ø 12 mm cylinder
Cylinders

A + stroke
C + stroke

Ø 16 ÷ 100 cylinder

C + stroke
B + stroke
A + stroke

Mass
Stroke 0
Stroke 0
Cyl. non Increase
magnetic
Ø magnetic per mm (g)
kg
kg
12 0,045 - 1,2
16 0,074 0,102 1,4
20 0,095 0,12 2
25 0,1355 0,155 2,85
32 0,233 0,292 4,06
40 0,394 0,43 5,47
50 0,39 0,446 6,4
63 0,64 0,772 9,7
80 1,19 1,275 14,85
100 1,72 1,92 19,7

Cyl. A B C A* B* C* V
D E F G H J L M N P Q R S T U W Y Z
Ø + STROKE hole thread

12 32 - 35,5 - - - 6 - 5 M5 M3 6,5 28,5 - 20 11 13 - 9 16 6 3,7 M4 8,2 9 3,4

16 32 - 35,5 42 - 45,5 6 - 5 M5 M3 6,5 31 28 28 11 20 20 10 17 5,8 3,7 M4 6,5 9 3,4
20 35 - 42 45 - 52 10 - 8 M5 M5 10 35 32 32 11 22 22 11 19 7,5 4,6 M5 7 10 4,6
25 35 - 42 45 - 52 10 - 8 G 1/8 M5 10 44,5 39 37 18 26 28 14 25 7,5 4,6 M5 7,5 10 4,6
32 37 42 49 47 52 59 12 23 10 G 1/8 M6 12 54 48 45 18 32 36 18 30 8,5 5,55 M6 9 16 5,7
40 40 47 55 45 52 60 16 29,5 13 G 1/8 M8 14 60 54,5 54,5 18 40 40 20 33 8,5 5,55 M6 9,5 16 5,7
50 40 46,5 55 45 51,5 60 16 35,5 13 G 1/4 M8 14 72 64 64 22 50 50 25 40 10,5 7,4 M8 10 16 6,8
63 42 50,5 59 47 55,5 64 20 43 17 G 1/4 M10 15 88 80 80 22 62 62 31 48 13,5 9,3 M10 10 20 9
80 52 60 71,5 57 65 76,5 25 50 22 G 3/8 M12 20 110 100 100 26 82 82 41 60 13,5 9,3 M10 15 20 9
100 52 60 71,5 57 65 76,5 25 56 22 G 3/8 M12 20 134 124 124 26 103 103 51,5 72 16,5 11,2 M12 15 25 11

* Magnetic version

56-I
Double-acting cylinder, through or hollow through piston rod

Double-acting cylinder with through piston rod W 101 . . / W 101 . . M Series

Ø 12 mm cylinder

Cylinders
Mass
Stroke 0
Cyl. non magnetic
Stroke 0 Increase
Ø magnetic kg per mm (g)
kg

12 0,055 - 1,4
A + stroke X + stroke 16 0,086 0,114 1,6
C + (2 x stroke)
20 0,112 0,137 2,65
25 0,165 0,185 3,5
32 0,295 0,354 5
40 0,5 0,536 7
50 0,478 0,534 8

Ø 16 ÷100 mm cylinder 63 0,79 0,922 12,2

80 1,345 1,43 18,7
100 1,875 2,075 23,6

A + stroke
B + stroke X + stroke
C + (2 x stroke)

Double-acting cylinder with hollow through piston rod W 131 . . / W 131 . . M Series
(from. Ø 20 ÷ 100 mm)

Cyl. Ø 12 16 20 25 32 40 50 63 80 100
K - - 2,5 2,5 3 4 4 6 6 6

For weights see table above

Cyl. A B C A* B* C* V
D E F G H J L M N P Q R S T U W X Y Z
Ø + STROKE hole thread

12 37 - 44 - - - 6 - 5 M5 M3 6,5 28,5 - 20 11 13 - 9 16 6 3,7 M4 8,2 3,5 9 3,4

16 37 - 44 47 - 54 6 - 5 M5 M3 6,5 31 28 28 11 20 20 10 17 5,8 3,7 M4 6,5 3,5 9 3,4
20 40 - 54 50 - 64 10 - 8 M5 M5 10 35 32 32 11 22 22 11 19 7,5 4,6 M5 7 7 10 4,6
25 40 - 54 50 - 64 10 - 8 G 1/8 M5 10 44,5 39 37 18 26 28 14 25 7,5 4,6 M5 7,5 7 10 4,6
32 42 52 66 52 62 76 12 23 10 G 1/8 M6 12 54 48 45 18 32 36 18 30 8,5 5,55 M6 9 7 16 5,7
40 45 59 75 50 64 80 16 29,5 13 G 1/8 M8 14 60 54,5 54,5 18 40 40 20 33 8,5 5,55 M6 9,5 8 16 5,7
50 45 58 75 50 63 80 16 35,5 13 G 1/4 M8 14 72 64 64 22 50 50 25 40 10,5 7,4 M8 10 8,5 16 6,8
63 47 64 81 52 69 86 20 43 17 G 1/4 M10 15 88 80 80 22 62 62 31 48 13,5 9,3 M10 10 8,5 20 9
80 52 68 91 57 73 96 25 50 22 G 3/8 M12 20 110 100 100 26 82 82 41 60 13,5 9,3 M10 15 11,5 20 9
100 52 68 91 57 73 96 25 56 22 G 3/8 M12 20 134 124 124 26 103 103 51,5 72 16,5 11,2 M12 15 11,5 25 11
* Magnetic version

57-I
 Single-acting cylinder, retracted piston rod

Single-acting cylinder, with retracted piston rod W 160 . . / W 160 . . M series

Ø 12 mm cylinder
Cylinders

A + stroke
C + stroke

Ø 16 ÷ 100 mm cylinder

A + stroke

C + stroke Mass
Stroke 0 Stroke 0
Cyl. non magnetic magnetic
Increase
Ø per mm (g)
kg kg

12 0,038 - 1,2
16 0,059 0,079 1,4
20 0,07 0,095 2
25 0,096 0,116 2,85
32 0,194 0,253 4,06
40 0,326 0,362 5,47
50 0,322 0,378 6,4
63 0,533 0,715 9,7
80 1,02 1,105 14,85
100 1,49 1,69 19,7

Cyl. A C A* C* V
D F G H J L M N P Q R S T U W Y Z
Ø + STROKE hole thread

12 27 28 - - 6 5 M5 M3 6,5 28,5 - 20 11 13 - 9 16 6 3,7 M4 8,2 9 3,4

16 22 23 37 38 6 5 M5 M3 6,5 31 28 28 11 20 20 10 17 5,8 3,7 M4 6,5 9 3,4
20 25 26 40 41 10 8 M5 M5 10 35 32 32 11 22 22 11 19 7,5 4,6 M5 7 10 4,6
25 25 26 40 41 10 8 G 1/8 M5 10 44,5 39 37 18 26 28 14 25 7,5 4,6 M5 7,5 10 4,6
32 32 33 47 48 12 10 G 1/8 M6 12 54 48 45 18 32 36 18 30 8,5 5,55 M6 9 16 5,7
40 35 36 45 46 16 13 G 1/8 M8 14 60 54,5 54,5 18 40 40 20 33 8,5 5,55 M6 9,5 16 5,7
50 35 36 45 46 16 13 G 1/4 M8 14 72 64 64 22 50 50 25 40 10,5 7,4 M8 10 16 6,8
63 37 39 47 49 20 17 G 1/4 M10 15 88 80 80 22 62 62 31 48 13,5 9,3 M10 10 20 9
80 47 53 57 63 25 22 G 3/8 M12 20 110 100 100 26 82 82 41 60 13,5 9,3 M10 15 20 9
100 47 53 57 63 25 22 G 3/8 M12 20 134 124 124 26 103 103 51,5 72 16,5 11,2 M12 15 25 11

* Magnetic version

58-I
Single-acting cylinder, extended piston rod

Single-acting cylinder with extended piston rod W 170 . . / W 170 . . M Series

Ø 12 mm cylinder

Cylinders
A + stroke
C + 2 stroke

Ø 16 ÷ 100 mm cylinder

A + stroke
Mass
B + stroke
C + 2 stroke Stroke 0
Cyl. non magnetic
Stroke 0 Increase
Ø magnetic kg per mm (g)
kg

12 0,045 - 1,2
16 0,7 0,098 1,4
20 0,86 0,111 2
25 0,122 0,142 2,85
32 0,212 0,271 4,06
40 0,366 0,402 5,47
50 0,352 0,408 6,4
63 0,59 0,772 9,7
80 1,104 1,189 14,85
100 1,576 1,776 19,7

Cyl. A B C A* B* C* V
D E F G H J L M N P Q R S T U W Y Z
Ø + STROKE hole thread

12 32 - 35,5 - - - 6 - 5 M5 M3 6,5 28,5 - 20 11 13 - 9 16 6 3,7 M4 8,2 9 3,4

16 27 - 30,5 42 - 45,5 6 - 5 M5 M3 6,5 31 28 28 11 20 20 10 17 5,8 3,7 M4 6,5 9 3,4
20 30 - 37 45 - 52 10 - 8 M5 M5 10 35 32 32 11 22 22 11 19 7,5 4,6 M5 7 10 4,6
25 30 - 37 45 - 52 10 - 8 G 1/8 M5 10 44,5 39 37 18 26 28 14 25 7,5 4,6 M5 7,5 10 4,6
32 32 37 44 47 52 59 12 23 10 G 1/8 M6 12 54 48 45 18 32 36 18 30 8,5 5,55 M6 9 16 5,7
40 35 42 50 45 52 60 16 29,5 13 G 1/8 M8 14 60 54,5 54,5 18 40 40 20 33 8,5 5,55 M6 9,5 16 5,7
50 35 41,5 50 45 51,5 60 16 35,5 13 G 1/4 M8 14 72 64 64 22 50 50 25 40 10,5 7,4 M8 10 16 6,8
63 37 45,5 54 47 55,5 64 20 43 17 G 1/4 M10 15 88 80 80 22 62 62 31 48 13,5 9,3 M10 10 20 9
80 47 55 66,5 57 65 76,5 25 50 22 G 3/8 M12 20 110 100 100 26 82 82 41 60 13,5 9,3 M10 15 20 9
100 47 55 66,5 57 65 76,5 25 56 22 G 3/8 M12 20 134 124 124 26 103 103 51,5 72 16,5 11,2 M12 15 25 11

* Magnetic version

59-I
 Cylinders with non-rotating piston rod

Non-rotating piston rod Non-rotating through piston rod

W 110 . . / W 110 . . M Series W 111 . . / W 111 . . M Series
Cylinders

A + stroke A + (2 x stroke)

Section: A-A Section: A-A

Non-rotating piston rod Non-rotating through piston rod

W 110 . . S / W 110 . . SM Series W 111 . . S / W 111 . . SM Series

(with safety distance) (with safety distance)

A + stroke A + (2 x stroke)

Section: A-A
Section: A-A

Mass Mass

Cyl. Stroke 0 non Stroke 0 Increase Cyl. Stroke 0 non Stroke 0 Increase per
Ø magnetic kg magnetic kg per mm (g) Ø magnetic kg magnetic kg mm (g)

16 0,092 0,12 1,6 16 0,104 0,132 1,8

20 0,133 0,158 2,45 20 0,15 0,175 3,1
25 0,185 0,205 3,3 25 0,214 0,234 3,95
32 0,33 0,39 4,85 32 0,392 0,452 5,8
40 0,545 0,58 6,7 40 0,651 0,686 8,2
50 0,6 0,656 7,6 50 0,688 0,744 9,2
63 0,96 1,092 11,5 63 1,11 1,242 14
80 1,75 1,835 17,25 80 1,905 1,99 21
100 2,63 2,83 22,8 100 2,785 2,985 26,7

60-I
Chart relating to load / protrusion

Cylinders
Load(N)
S
Protrusion P
Load(N)

S = point of application of load

P = load (N)

Protrusion (mm) Protrusion (mm)

Overall dimensions of non-rotating cylinders

Cyl. W110 W111 W110M W111M

X L A + stroke A + (2 x stroke) A* + stroke A* + (2 x stroke)
D DD E F H K M P Q R S Y Z
Ø

16 3,5 3,5 42,5 51 52,5 61 6 4 6 3,5 3,5 27,5 7 6 20 20 10 27,5 M3

20 7 7 50 62 60 72 7,5 6 7,5 4,5 4,5 31,5 8 7,5 22 22 11 31,5 M4

25 7 7 50 62 60 72 7,5 6 7,5 4,5 5 36 8 7,5 26 28 14 38 M4

32 7 12 59 76 69 86 9 8 10 5,5 6 44,5 10 10 32 36 18 47,5 M4

40 8 15 65 85 70 90 10,5 10 10 5,5 6 53,5 10 10 40 40 20 53,5 M5

50 8,5 15 67 87 72 92 10,5 10 11 6,5 7 63,5 12 11 50 50 25 63,5 M6

63 8,5 17 71 93 76 98 13,5 12 14 9 9 79,5 12 15 62 62 31 79,5 M6

80 11,5 19,5 85,5 105 90,5 110 13,5 14 14 9 9 99,5 14 15 82 82 41 99,5 M8

100 11,5 19,5 87,5 107 92,5 112 16,5 16 16,5 10,5 10,5 123,5 16 17 103 103 51,5 123,5 M8

* Magnetic version

Overall dimensions of cylinder with non-rotating

piston rod and safety distance option

Cyl. W110 W111 W110M W111M Accident prevention safety distance in

A + stroke A + (2 x stroke) A* + stroke A* + (2 x stroke)
L a accordance with EC rules EN 294 to
Ø
be provided by the user.
16 67,5 76 77,5 86 28,5 28,5
20 70 82 80 92 27 27
25 70 82 80 92 27 27
32 79 96 89 106 32 27
40 85 105 90 110 35 28
50 87 107 92 112 35 28,5
63 91 113 96 118 37 28,5
80 100,5 120 105,5 125 34,5 26,5
100 102,5 122 107,5 127 34,5 26,5

* Magnetic version

NOTE: for additional dimensions, please refer to models without non-rotating device

61-I
 Options upon request

Tandem cylinder

W 1A 032 050 M Tandem short stroke "W series"

Cylinders

Vér.
L2 = A + C2 L1 = B + C1 L0 = (A+B) + C1 + C2
Ø
Magnetic option
(upon request) 16 L2 = 37 + C2 L1 = 22 + C1 L0 = 59 + C1 + C2
20 L2 = 40 + C2 L1 = 25 + C1 L0 = 65 + C1 + C2
Stroke (C1 and C2)
25 L2 = 40 + C2 L1 = 25 + C1 L0 = 65 + C1 + C2
32 L2 = 42 + C2 L1 = 23 + C1 L0 = 65 + C1 + C2
Bore (mm)
40 L2 = 45 + C2 L1 = 26,5 + C1 L0 = 71,5 + C1 + C2

Tandem with double thrust (output only) 50 L2 = 45 + C2 L1 = 26 + C1 L0 = 71 + C1 + C2

63 L2 = 47 + C2 L1 = 29 + C1 L0 = 76 + C1 + C2
Series 80 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1 + C2
100 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1 + C2

Tandem short stroke "W series" magnetic

Cyl.
L2 = A + C2 L1 = B + C1 L0 = (A+B) + C1 + C2
Ø

16 L2 = 47 + C2 L1 = 37 + C1 L0 = 84 + C1 + C2
20 L2 = 50 + C2 L1 = 40 + C1 L0 = 90 + C1 + C2
25 L2 = 50 + C2 L1 = 40 + C1 L0 = 90 + C1 + C2
32 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1 + C2
40 L2 = 50 + C2 L1 = 36.5 + C1 L0 = 86.5 + C1 + C2
50 L2 = 50 + C2 L1 = 36 + C1 L0 = 86 + C1 + C2
63 L2 = 52 + C2 L1 = 39 + C1 L0 = 91 + C1 + C2
80 L2 = 57 + C2 L1 = 48 + C1 L0 = 105 + C1 + C2
100 L2 = 57 + C2 L1 = 48 + C1 L0 = 105 + C1 + C2

Tandem cylinder with two positions Stroke C1 is always lower than stroke C2

W 1B 032 050 090 M Tandem short stroke two positions "W series"
Cyl.
Magnetic option L2 = A + C2 L1 = B + C1 L0 = (A+B) + C1< + C2
Ø
(upon request)
16 L2 = 37 + C2 L1 = 22 + C1 L0 = 59 + C1< + C2
Stroke of head cylinder 20 L2 = 40 + C2 L1 = 25 + C1 L0 = 65 + C1< + C2
25 L2 = 40 + C2 L1 = 25 + C1 L0 = 65 + C1< + C2
Stroke of rear cylinder (C1)
32 L2 = 42 + C2 L1 = 23 + C1 L0 = 65 + C1< + C2
40 L2 = 45 + C2 L1 = 26.5 + C1 L0 = 71.5 + C1< + C2
Bore (mm)
50 L2 = 45 + C2 L1 = 26 + C1 L0 = 71 + C1< + C2
63 L2 = 47 + C2 L1 = 29 + C1 L0 = 76 + C1< + C2
Option tandem two positions
80 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1< + C2

Series 100 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1< + C2

Tandem short stroke two positions "W series" magnetic

Cyl.
L2 = A + C2 L1 = B + C1 L0 = (A+B) + C1< + C2
Ø

16 L2 = 47 + C2 L1 = 37 + C1 L0 = 84 + C1< + C2
20 L2 = 50 + C2 L1 = 40 + C1 L0 = 90 + C1< + C2
25 L2 = 50 + C2 L1 = 40 + C1 L0 = 90 + C1< + C2
32 L2 = 52 + C2 L1 = 38 + C1 L0 = 90 + C1< + C2
40 L2 = 50 + C2 L1 = 36.5 + C1 L0 = 86.5 + C1< + C2
50 L2 = 50 + C2 L1 = 36 + C1 L0 = 87 + C1< + C2
63 L2 = 52 + C2 L1 = 39 + C1 L0 = 91 + C1< + C2
80 L2 = 57 + C2 L1 = 48 + C1 L0 = 105 + C1< + C2
100 L2 = 57 + C2 L1 = 48 + C1 L0 = 105 + C1< + C2

62-I
Multiple position cylinder WS (see drawing for references)

Cylinders
Multiple position tandem short stroke "W series"
Cyl.
L3 = A + C3 L2 = B + C2 L1 = D + C1 L0 = (A+B+D) + C1< + C2< + C3
Ø

16 L3 = 37 + C3 L2 = 27 + C2 L1 = 22 + C1 L0 = 86 + C1< + C2< + C3
20 L3 = 40 + C3 L2 = 30 + C2 L1 = 25 + C1 L0 = 95 + C1< + C2< + C3
25 L3 = 40 + C3 L2 = 30 + C2 L1 = 25 + C1 L0 = 95 + C1< + C2< + C3
32 L3 = 42 + C3 L2 = 28 + C2 L1 = 23 + C1 L0 = 93 + C1< + C2< + C3
40 L3 = 45 + C3 L2 = 31.5 + C2 L1 = 26.5 + C1 L0 = 103 + C1< + C2< + C3
50 L3 = 45 + C3 L2 = 31 + C2 L1 = 26 + C1 L0 = 102 + C1< + C2< + C3
63 L3 = 47 + C3 L2 = 36 + C 2 L1 = 29 + C1 L0 = 112 + C1< + C2< + C3
80 L3 = 52 + C3 L2 = 38 + C2 L1 = 38 + C1 L0 = 128 + C1< + C2< + C3
100 L3 = 52 + C3 L2 = 38 + C 2 L1 = 38 + C1 L0 = 128 + C1< + C2< + C3

Multiple position tandem short stroke "W series" magnetic

Cyl.
L3 = A + C3 L2 = B + C2 L1 = D + C1 L0 = (A+B+D) + C1< + C2< + C3
Ø

16 L3 = 47 + C3 L2 = 42 + C2 L1 = 37 + C1 L0 = 126 + C1< + C2< + C3

20 L3 = 50 + C3 L2 = 45 + C2 L1 = 40 + C1 L0 = 135 + C1< + C2< + C3
25 L3 = 50 + C3 L2 = 45 + C2 L1 = 40 + C1 L0 = 135 + C1< + C2< + C3
32 L3 = 52 + C3 L2 = 43 + C2 L1 = 38 + C1 L0 = 133 + C1< + C2< + C3
40 L3 = 50 + C3 L2 = 41.5 + C2 L1 = 36.5 + C1 L0 = 128 + C1< + C2< + C3
50 L3 = 50 + C3 L2 = 41 + C2 L1 = 36 + C1 L0 = 127 + C1< + C2< + C3
63 L3 = 52 + C3 L2 = 44 + C2 L1 = 39 + C1 L0 = 135 + C1< + C2< + C3
80 L3 = 57 + C3 L2 = 48 + C2 L1 = 48 + C1 L0 = 153 + C1< + C2< + C3
100 L3 = 57 + C3 L2 = 48 + C2 L1 = 48 + C1 L0 = 153 + C1< + C2< + C3

NOTE: options with non-rotating rod are possible

Additional dimensions are reported in W100 ... series at page 56

63-I
 Mounting elements - accessories

Rear male hinge

W 700 . . . / W 700 . . . M series
Cylinders

W 760 . . . / W 760 . . . M series

W 770 . . . / W 770 . . . M series

Mass
Cyl. Ø Y Z Ø WH7 V
W700.../W700...M W760.../W760...M W770.../W770...M
Stroke 0 Stroke 0 Stroke 0 12 - - - -
Stroke 0 Increase Stroke 0 ncrease Stroke 0 ncrease
Cyl. non non non
magnetic per mm magnetic per mm magnetic per mm 16 5,5 9 6 H7
6,2
Ø magnetic magnetic magnetic
kg (g) kg (g) kg (g)
kg kg kg
H7
12 - - - - - - - - - 20 5,5 9 6 6,5
H7
16 0,082 0,11 1,4 0,067 0,087 1,4 0,078 0,106 1,4 25 6 12 6 8
20 0,1075 0,1325 2 0,0825 0,0975 2 0,0985 0,1235 2 H7
32 9 14 10 11
25 0,1585 0,1785 2,85 0,119 0,139 2,85 0,145 0,165 2,85
H7
40 10 16 12 13
32 0,2765 0,3355 4,06 0,2375 0,2965 4,06 0,2555 0,3155 4,06
H7
40 0,4705 0,5065 5,47 0,4025 0,4385 5,47 0,442 0,4785 5,47 50 12 17 12 16,5
50 0,417 0,473 6,4 0,349 0,405 6,4 0,379 0,435 6,4 63 14 21 16 H7
18
63 0,6815 0,8135 9,7 0,5745 0,7565 9,7 0,6315 0,9135 9,7
80 14 21 16 H 7 16,5
80 1,2385 1,3235 14,85 1,0685 1,1535 14,85 1,1525 1,2375 14,85
100 1,775 1,975 19,7 1,545 1,745 19,7 1,631 1,831 19,7 100 17 25 20 H 7 21

Fixing screws Nipple

Ø D

Cyl. Ø 12 16* 20 25 32 40 50 63 80 100

M 3 3 4 4 5 5 6 8 8 10

Part
Cyl. Ø A AM C D d
number
12-16 22,5 16 6,5 6x1 M3 WF-50012
20-25 30 20 10 8 x 1,25 M5 WF-50020
32 34 22 12 10 x 1,25 M6 WF-50032
40 38 24 14 12 x 1,25 M8 WF-50040
50 46 32 14 16 x 1,5 M8 WF-50050
63 47 32 15 16 x 1,5 M 10 WF-50063
* Magnetic version only for bore 16, the fixing screws have
to be of the non magnetic type. 80-100 60 40 20 20 x 1,5 M 12 WF-50080

64-I