ISO

CATEGORY
ER COLLET CHUCK SYSTEM J-3
SKS COLLET CHUCK SYSTEM J-4
SBL SLIM-FIT COLLET CHUCK J-5
SBLC SLIM-FIT COLLET CHUCK J-6
EBL SLIM-FIT COLLET CHUCK J-7
 TOOLING MEASUREMENT GUIDE FOR SPECIAL ORDERS
ISO

When ordering the custom-made ISO tool holders, please offer the following dimensions
(shown as the drawing) by filling out the form. Thank you!

Machine Spindle
d3
θ
l4
d2

D
d1
Please measure
l2 GAUGE LINE
the clearance with
a thickness gauge.
l3

l1

l5

J-2 General catalogue

 ISO / ER COLLET CHUCK

ISO
W/OUT SLOTS
ISO / ER 立銑刀夾頭

ＴＷ PAT NO. M298033

ＴＷ PAT NO. M311791
ＪＰ PAT NO. 3128766
ＫＲ PAT NO. 20-0433603
ＣＮ PAT NO. ZL200620132661.0
ＣＨ PAT NO. 696550
ＴＲ PAT NO. TR 2007 02942 Y
ＩＴ PAT NO. N.0000266731

SIZE WEIGHT
MODEL NO. TYPE L l1 l2 l3 D d1 d2 d3 T RANGE (KGS)
86102 ISO20 x ER11A - 52 83.3 52 2 8 33 19 21.642 8.5 M6 1~7 0.55
86103 ISO20 x ER16AD - 52 85.4 52 2 15.9 30 28 22.255 8.5 M10 1 ~ 10 0.60
86104 ISO20 x ER16A - 52 83.3 52 2 8 33 28 21.642 8.5 M10 1 ~ 10 0.60
86105 ISO20 x ER20AD - 52 85.4 52 2 15.9 30 34 22.255 8.5 M10 1 ~ 13 0.65
86106 ISO20 x ER20A - 52 83.3 52 2 8 33 34 21.642 8.5 M12 1 ~ 13 0.65
86112 ISO25 x ER11A - 52 89.7 52 2.95 8 37 19 25.114 8.5 M6 1~7 0.60
86114 ISO25 x ER16A - 52 89.7 52 2.95 8 37 28 24.91 8.5 M10 1 ~ 10 0.65
86116 ISO25 x ER20A - 52 89.7 52 2.95 8 37 34 25.114 8.5 M12 1 ~ 13 0.70
86122 ISO30 x ER11A - 80 127.8 80 3.2 15.9 50 19 31.75 13 M6 1~7 0.70
86124 ISO30 x ER16A - 63 110.8 63 3.2 15.9 50 28 31.75 13 M10 1 ~ 10 0.80
86126 ISO30 x ER20A - 63 110.8 63 3.2 15.9 50 34 31.75 13 M12 1 ~ 13 0.85
86128 ISO30 x ER25 - 63 110.8 63 3.2 15.9 50 42 31.75 13 M16 1 ~ 16 0.90
86130 ISO30 x ER32 - 63 110.8 63 3.2 15.9 50 50 31.75 13 M16 2 ~ 20 0.90
86132 ISO30 x ER40 - 57 104.8 57 3.2 15.9 50 63 31.75 13 M16 3 ~ 26 0.95

Features:
▸ Whole shank body with grinding.
▸ Balance: G2.5 40,000RPM.
Standard Accessory: ● NUT
Collet Nut Pull Stud Preset Screw Spanner

P.W-7~28 P.W-48 P.W-64 P.W-88 P.W-68~71

General catalogue J-3

 ISO / SKS COLLET CHUCK
ISO

W/OUT SLOTS
ISO / SKS 高速機專用夾頭

ＴＷ PAT NO. M270871

SIZE WEIGHT
MODEL NO. TYPE L l1 l2 l3 D d1 d2 d3 T RANGE (KGS)
86852 ISO20 x SKS6 - 45 76.3 45 3.9 8 33 18 21.642 8.5 M8 3~6 0.55
86854 ISO20 x SKS6 - 60 91.3 60 3.9 8 33 18 21.642 8.5 M8 3~6 0.60
86856 ISO20 x SKS10 - 45 76.3 45 3.9 8 33 30 21.642 8.5 M12 3 ~10 0.60
86858 ISO20 x SKS10 - 60 91.3 60 3.9 8 33 30 21.642 8.5 M12 3 ~ 10 0.70
86862 ISO25 x SKS6 - 45 82.7 45 2.0 8 37 18 25 8.5 M8 3~6 0.60
86864 ISO25 x SKS6 - 60 97.7 60 2.0 8 37 18 25 8.5 M8 3~6 0.65
86866 ISO25 x SKS10 - 40 77.7 40 2.0 8 37 30 25 8.5 M12 3 ~ 10 0.70
86868 ISO25 x SKS10 - 60 97.7 60 2.0 8 37 30 25 8.5 M12 3 ~ 10 0.75
86872 ISO30 x SKS6 - 45 92.8 45 3.2 15.9 50 18 31.75 13 M8 3~6 0.65
86874 ISO30 x SKS6 - 60 107.8 60 3.2 15.9 50 18 31.75 13 M8 3~6 0.70
86876 ISO30 x SKS10 - 45 92.8 45 3.2 15.9 50 30 31.75 13 M12 3 ~ 10 0.80
86878 ISO30 x SKS10 - 60 107.8 60 3.2 15.9 50 30 31.75 13 M12 3 ~ 10 0.85
86880 ISO30 x SKS16 - 60 107.8 60 3.2 15.9 50 40 31.75 13 M18 3 ~ 16 0.72

Features:
▸ Whole shank body with grinding.
Product information:
▸ Balance: G2.5 25,000 rpm. Higher balancing grade and revolution can be done upon request but additional charge is needed.
Standard Accessory: ● NUT
Collet Nut Pull Stud Preset Screw Spanner

P.W-29~32 P.W-53~54 P.W-64 P.W-88 P.W-68~72

J-4 General catalogue

 ISO / SBL SLIM-FIT COLLET CHUCK

ISO
W/OUT SLOTS
ISO / SBL 後拉式立銑刀夾頭

ø13
°

ø31.75
ＴＷ PAT NO. M274178

RECOMMENDED
TORQUE SIZE WEIGHT
MODEL NO. TYPE L l1 l2 d1 d2 T RANGE (KGS)
N.m 1bf-ft
86822 ISO30 x SBL6 - 70 117.8 70 39 14 18 M6 12 9 3~6 0.70
86824 ISO30 x SBL12 - 70 117.8 70 46 26 30 M10 45 33 3 ~ 12 0.80
86826 ISO30 x SBL20 - 80 127.8 80 58 35 37 M12 60 44 3 ~ 20 0.85

Features:
▸ Slim designs avoid interference.
▸ Chucking in the front part of collet which hides inside.
▸ Good design for high speed rotation with good stability because of non-clamping nut.
▸ 4° taper angle is good for powerful chucking and can strip easily.
Product information:
▸ Balance: G2.5 25,000 rpm. Higher balancing grade and revolution can be done upon request but additional charge is needed.
Collet Pull Stud Screw Spanner

P.W-33 P.W-64 P.W-91 P.W-72

General catalogue J-5

 ISO / SBLC SLIM-FIT COLLET CHUCK
ISO

W/OUT SLOTS
ISO / SBLC 後拉式立銑刀夾頭

ø13
°

ø31.75
ＴＷ PAT NO. M274178

RECOMMENDED
TORQUE SIZE WEIGHT
MODEL NO. TYPE L l1 l2 d1 d2 T RANGE (KGS)
N.m 1bf-ft
86822C ISO30 x SBLC6 - 70 117.8 70 39 14 18 M6 12 9 3~6 0.70
86824C ISO30 x SBLC12 - 70 117.8 70 46 26 30 M10 45 33 3 ~ 12 0.80
86826C ISO30 x SBLC20 - 80 127.8 80 58 35 37 M12 60 44 3 ~ 20 0.85

Features:
▸ Slim designs avoid interference.
▸ Chucking in the front part of collet which hides inside.
▸ Good design for high speed rotation with good stability because of non-clamping nut.
▸ 4° taper angle is good for powerful chucking and can strip easily.
Product information:
▸ Balance: G2.5 25,000 rpm. Higher balancing grade and revolution can be done upon request but additional charge is needed.
▸ Used with SLC sealed collet and coolant through cutters.
Standard Accessory: ● SPANNER
Collet Pull Stud Screw Spanner

P.W-34 P.W-64 P.W-91 P.W-72

J-6 General catalogue

 ISO / EBL SLIM-FIT COLLET CHUCK

ISO
ISO / EBL 後拉式刀桿

TORQUE SIZE WEIGHT

MODEL NO. TYPE L l1 I2 d1 d2 T
N.m lbf-ft RANGE (KGS)
113.277.06.070 ISO30 x EBL6 - 70 117.8 70 41.2 19.05 23.1 M6 x 1.0P 12 9 3~6 0.52

▸ BT40 x SBL6 - 70
▸ SBL ▸ BT40 x EBL6 - 70
▸ EBL

Features:
▸ The extended length of EBL collet and special longer inner hole design of holder allow deeper tool insertion and shorter tool overhanging length,
improving the machining stability.
▸ The optimized design of thicker neck improves the machining rigidity and eliminates micro-vibration.
▸ Use with CTS to achieve better dustproof ability and chip evacuation. Capable of coolant pressure up to 25 bar.
Product information:
▸ Balance: G2.5 25,000rpm.
Standard Accessory: ● ALLEN WRENCH ●TORX WRENCH
Collet Sealed Collet Pull Stud Screw Spanner Spanner

P.W-35 P.W-36 P.W-64 P.W-91 P.W-72

General catalogue J-7

 MEMO

J-8 General catalogue