AIR CONDITIONER

REMOTE CONTROLLER MANUAL

The design and specification are subject to change without prior notice
for product improvement. Consult with the sales agency or manufacturer
for details.

MODELS

KSM-IW10WAE-7J1M
KSM-IW15WAE-7J1M
KSM-IW20WAE-7J1M
KSM-IW26WAE-7J1M
KSM-IW30WAE-7J1M

Thank you very much for purchasing our air conditioner.

Please read this owner's manual carefully before using
KPII2018416-15001
your air conditioner.

KPII2018416-15001
 Function Buttons

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
CONTENTS control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

Remote controller Specifications................................................... 1 ON/OFF ECO

Turns the unit on or off Used to enter the energy
efficient mode.
Function buttons .................. ......................................................... 2
MODE
Handling the remote controller ...................................................... 4 Scrolls through operation TEMP p
modes as follows: Increases temperate in
Remote LCD screen indicators ..................................................... 6 COOL g DRY g FAN 1OC increments.
Max. temperature is
How to use the basic functions........................................................ 7 30OC .
FAN SPEED
Selects fan speeds in
TEMP q
How to use the advanced functions ............................................... 13 the following order:
Decreases temperate in
AUTO g LOW g
ON/OFF 1OC increments.
MED g HIGH ECO
Min. temperature is
17OC .
SLEEP MODE TIMER
ON
Saves energy during TEMP
TIMER ON
sleeping hours Sets timer to turn unit
TIMER
Remote Controller Specifications FAN OFF on (seeHow to Use
Basic Functions for
FRESH
SLEEP FRESH instructions)
Press this button, the
Model RG57A3/BGCEF, RG57A3/BGCEFU1,RG57A8/BGCEF Ionizer/Plasma Dust SELF
TURBO CLEAN LED FOLLOW
TIMER OFF
ME
Collector(depending Sets timer to turn unit
on models) is energized off (see How to Use
Rated Voltage 3.0V(Dry batteries R03/LR03×2) and will help to remove Basic Functions for
pollen and impurities instructions)
Signal Receiving Range 8m
from the air.
SWING
Starts and stops louver
TURBO
Environment
O O O O
-5 C~60 C(23 F~140 F) Enables unit to reach movement
preset temperature in FOLLOW ME
shortest possible time Temperature sensing
and room temperature
SELF CLEAN display button.
Starts and stops
self clean feature. LED
,
Turns indoor unit s LED
display on and off.

MODEL:RG57A8/BGCEF

1 2
 Function Buttons Handling The Remote Controller
NOT SURE WHAT A FUNCTION DOES? TIPS FOR USING REMOTE CONTROL
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote Refer to the How to Use Basic Functions and
control. The following is a brief introduction to the remote control itself. For instructions on how to The remote control must be used within 8
How to Use Advanced Functions sections
operate your air conditioner, refer to the How to Use Basic Functions section of this manual. of this manual for a detailed description of meters of the unit.
how to use your air conditioner. The unit will beep when remote signal is
SHORT CUT
ON/OFF Sets and activates your received.
Turns the unit on or off favourite pre-settings SPECIAL NOTE
Curtains, other materials and direct sunlight
TEMP p Button designs on your unit may differ can interfere with the infrared signal receiver.
MODE Increases temperate in slightly from the example shown.
Scrolls through operation 1OC/1OF increments. If the indoor unit does not have a particular Remove batteries if the remote will not be
,
modes as follows: Max. temperature is function, pressing that function s button used more than 2 months.
COOL g DRY g FAN 30OC(86OF) . on the remote control will have no effect.
TEMP q ,,When there are wide differences between
,,
Decreases temperate in ,, Remote controller,,Illustration and
,, ,,
FAN SPEED USER'S MANUAL on function description,
Selects fan speeds in 1OC/1OF increments. the description of USER'S MANUAL
the following order: Min. temperature is shall prevail.
AUTO g LOW g 17OC(62OF) .
MED g HIGH
ON/OFF SHORT NOTE: Press and hold Inserting and Replacing Batteries
CUT
SLEEP p and q buttons Your air conditioning unit comes with two AAA
Saves energy during TIMER together for 3 seconds will batteries. Put the batteries in the remote control
MODE ON
sleeping hours TEMP
alternate the temperature before use.
display between the 1. Slide the back cover from the remote
TIMER
FRESH FAN OFF
O
C & OF scale. control downward, exposing the battery
Press this button, the (Applicable to model of compartment.
Ionizer/Plasma Dust SLEEP FRESH
RG57A3/BECEFU1 only).
Collector(depending 2. Insert the batteries, paying attention to match
on models) is energized SELF
TURBO CLEAN LED FOLLOW
ME
TIMER ON up the (+) and (-) ends of the batteries with
and will help to remove Sets timer to turn unit the symbols inside the battery compartment.
pollen and impurities on (seeHow to Use 3. Slide the battery cover back into place.
from the air. Basic Functions for
instructions)
TURBO TIMER OFF BATTERY NOTES
Enables unit to reach Sets timer to turn unit
preset temperature in off (see How to Use For optimum product performance:
shortest possible time Basic Functions for Do not mix old and new batteries, or
instructions) batteries of different types.
SELF CLEAN Do not leave batteries in the remote control
SWING ,
Starts and stops Starts and stops louver if you don t plan on using the device for
self clean feature. movement more than 2 months.

LED FOLLOW ME
, Temperature sensing
Turns indoor unit s LED and room temperature BATTERY DISPOSAL
display on and off. display button.
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
MODEL:RG57A3/BGCEF,RG57A3/BGCEFU1 proper disposal of batteries.

3 4
NOTE: Remote LCD Screen Indicators
The device could comply with the local national regulations.
Information are displayed when the remote controller is powered up.
In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the Transmission Indicator
following two conditions: Lights up when remote sends
(1) This device may not cause harmful interference, and signal to indoor unit
(2) this device must accept any interference received, including interference that may
cause undesired operation. ON/OFF display
Appears when the unit is turned on,
This equipment has been tested and found to comply with the limits for a Class B digital and disappears when it is turned off
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide MODE display
reasonable protection against harmful interference in a residential installation. This Displays the current TIMER ON display TIMER OFF display
equipment generates, uses and can radiate radio frequency energy and, if not installed mode, including: Displays when TIMER Displays when TIMER
and used in accordance with the instructions, may cause harmful interference to radio COOL ON is set OFF is set
communications. However, there is no guarantee that interference will not occur in a DRY
ECO display
particular installation. If this equipment does cause harmful interference to radio or Displays when
FAN ECO function is
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following activated(applicable
measures: to RG57A8/BGCEF
Reorient or relocate the receiving antenna. only).
Increase the separation between the equipment and receiver.
Battery display
Connect the equipment into an outlet on a circuit different from that to which the Low battery
receiver is connected. detection
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could SLEEP display
void user s authority to operate the equipment. Displays when
SLEEP function
is activated

FOLLOW ME
display
Indicates that
the FOLLOW ME
function is on

FAN SPEED display

Displays selected FAN SPEED:
HIGH, MED,
or LOW
Temperature/Timer display
This display is blank when
Displays the set temperature by default, or timer setting
set to AUTO speed or DRY mode.
when using TIMER ON/OFF functions
Temperature range: 17-30 C/62-86 F
o O

Timer setting range: 0-24 hours

This display is blank when operating in FAN mode.
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual
operation only the relative functional signs are shown on the display window.

5 6
How To Use The Basic Functions How To Use The Basic Functions

SETTING TEMPERATURE
The operating temperature range for units is DRY operation(dehumidifying)
17-30 OC/62-86 OF. You can increase or
decrease the set temperature in 1 OC/1 OF 1. Press the MODE button to select DRY
increments. mode.
2. Set your desired temperature using the
Temp or Temp button.
3. Press the ON/OFFbutton to start the unit.
COOL operation 2 2 ,
4 ON/OFF SHORT
CUT 3 ON/OFF SHORT NOTE: FAN SPEED can t be changed in
1. Press the MODE button to select CUT
DRY mode.
COOL mode. 1 MODE TIMER
MODE TIMER

2. Set your desired temperature using TEMP

ON
1 TEMP
ON

the Temp or Temp button. 3 FAN

TIMER
OFF FAN
TIMER
OFF
3. Press the FAN button to select the
SLEEP FRESH
fan speed: AUTO, LOW, MED, or SLEEP FRESH

HIGH. SELF
TURBO CLEAN LED FOLLOW
ME
SELF
TURBO CLEAN LED FOLLOW
ME
4. Press the ON/OFF button to start the
unit.

FAN operation

1. Press the MODE button to select FAN

mode.
2. Press FAN button to select the fan
speed: AUTO, LOW, MED or HIGH.
ON/OFF SHORT
3. Press the ON/OFFbutton to start the 3 CUT

unit.
,
1 MODE TIMER
ON
TEMP
NOTE: You can t set temperature in FAN
,
mode. As a result, your remote control s
2 FAN
TIMER
OFF

LCD screen will not display temperature. SLEEP FRESH

SELF
TURBO CLEAN LED FOLLOW
ME

7 8
 TIMER OFF function
Setting the TIMER function The TIMER OFF function allows you to NOTE: When setting the TIMER ON or
set a period of time after which the unit TIMER OFF functions, up to 10 hours,
X4
1 2 will automatically turn off, such as when the time will increase in 30 minute
Your air conditioning unit has two
timer-related functions: you wake up. increments with each press. After 10
TIMER ON- sets the amount of timer after hours and up to 24, it will increase in 1
which the unit will automatically turn on. 1. Press the TIMER OFF button. By
TIMER ON TIMER ON hour increments. The timer will revert to
TIMER OFF- sets the amount of time after default, the last time period that you
set and an "h" (indicating hours)will zero after 24 hours.
which the unit will automatically turn off. You can turn off either function by
appear on the display.
Note: This number indicates the setting its timer to " 0.0h " .
TIMER ON function
The TIMER ON function allows you to set amount of time after the current time
a period of time after which the unit will 3 4 that you want the unit to turn off.
1sec For example, if you set TIMER OFF for
automatically turn on, such as when you 2sec 5 hours, " 5.0h " will appear on the
come home from work.
screen, and the unit will turn off after
1. Press the TIMER ON button. By 5 hours.
default, the last time period that you
2. Press the TIMER OFF button repeatedly
set and an "h" (indicating hours)will
to set the time when you want the unit to
appear on the display.
turn off.
Note: This number indicates the
ON/
OFF

3. Wait 2 seconds, then the TIMER OFF

MO
DE
SH
FA CUORT

amount of time after the current time

N TE T
MP TIM
ER
SLEE ON

function will be activated. The digital Continue to press

P TIM
ER
OFF

that you want the unit to turn on.

For example, if you set TIMER ON for
display on your remote control will then TIMER ON or
return to the temperature display.
ON/OFF

2 hours, " 2.0h " will appear on the Example: Setting unit to turn on after 2.5 SHORT
CUT TIMER OFF until
screen, and the unit will turn on after hours. MODE TIMER desired time is
ON
2 hours. TEMP reached.
1 2
x10
TIMER
FAN
2. Press the TIMER ON button repeatedly OFF

to set the time when you want the unit to SLEEP FRESH
turn on. SELF
LED FOLLOW
3. Wait 2 seconds, then the TIMER ON
TURBO CLEAN
TIMER OFF TIMER OFF ME

function will be activated. The digital

display on your remote control will then
return to the temperature display.

3 4
1sec 2sec

ON
/OFF

MOD
E SH
FA CUORT
N TE T
MP TIM
ER
SLEE ON
P TIM
ER
OF
F

Example: Setting unit to turn off after 5

hours.

9 10
Setting both TIMER ON and TIMER OFF at the same time Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off
(see the figure below)
Keep in mind that the time periods you set for both functions refer to hours after the
current time. For example, say that the current time is 1:00 PM, and you want the unit Your remote display
to turn on automatically at 7:00 PM. You want it to operate for 2 hours, then automa-
tically turn off at 9:00 PM.
Timer on
Do the following:
Timer is set To turn ON
6 hours from current time
1 2 3 4
X12
3sec
Timer off
TIMER ON TIMER ON
Timer is set to turn OFF
8 hours from current time

ON
/OFF

MO
DE
SH
CUORT
TE T
MP TIM
ER
ON

5 6 7 8 Unit turns Unit turns

X16 Timer starts
ON OFF
3sec
TIMER OFF TIMER OFF

ON
/OFF

MO

2PM 3PM 4PM 5PM 6PM 7PM 8PM 9PM

DE
SH
CUORT
TE
MP TIM
ER
T

ON
Current
time 1PM
6 hours later
8 hours later

11 12
How To Use The Advanced Functions How To Use The Advanced Functions

TURBO function ECO function

(for RG57A8/BGCEF only) SHORTCUT function
The TURBO function makes the unit work (For RG57A3/BGCEF, RG57A3/BGCEFU1 only)
extra hard to reach your present temperature Used to enter the energy efficient mode.
in the shortest amount of time possible. Under cooling mode, press this button, Used to restore the current settings or resume
When you press the TURBO button in the remote controller will adjust the previous settings.
COOL mode, the unit will blow cool air temperature automatically to 24OC/75OF, Push this button when remote controller is on, the
with strongest wind setting to jump-start fan speed of Auto to save energy(but system will automatically revert back to the
the cooling process. only if the set temperature is less than previous settings including operating mode, setting
When you press the TURBO button in 24OC/75OF). If the set temperature is temperature, fan speed level and sleep feature
HEAT mode, for units with Electric heat above 24OC/75OF , press the ECO button, (if activated).
elements, the Electric Heater will activate the fan speed will change to Auto, the If pushing more than 2 seconds, the system will
ON/OFF SHORT
and jump-start the heating process. set temperature will remain unchanged. CUT automatically restore the current operation settings
NOTE: including operating mode, setting temperature, fan
Pressing the ECO button, or modifying MODE TIMER
ON speed level and sleep feature(if activated ).
the mode or adjusting the set temperature TEMP
SELF CLEAN function
to less than 24OC/75OF will stop ECO FAN
TIMER
OFF
Airborne bacteria can grow in the moisture that operation. SWING function
condenses around heat exchanger in the unit. Under ECO operation, the set temper- SLEEP FRESH

With regular use, most of this moisture is ature should be 24OC/75OF or more. it Swing Button
evaporated from the unit. By pressing the may result in insufficient cooling. If you
SELF
TURBO CLEAN LED FOLLOW
ME Used to stop or start vertical louver movement
CLEAN button, your unit will clean itself feel uncomfortable, just press the ECO and set the desired left/right air flow direction.
automatically. After cleaning, the unit will turn button again to stop it. The vertical louver changes 6 degree in angle
off automatically. Pressing the CLEAN button for each press. If keep pushing more than 2
mid-cycle will cancel the operation and turn seconds, the vertical louver auto swing feature
off the unit. is activated.

You can use CLEAN as often as you like. Swing Button

Note: You can only activate this function Used to stop or start horizontal louver movement
in COOL or DRY mode. or set the desired up/down air flow direction. The
MODEL:RG57A3/BGCEF louver changes 6 degree in angle for each press.
If keep pushing more than 2 seconds, the louver
RG57A3/BGCEFU1 will swing up and down automatically.
FOLLOW ME function
ON/OFF
ECO
The FOLLOW ME function enables the
remote control to measure the temper- MODE TIMER
SLEEP Function
ature at its current location. When using TEMP
ON

COOL, or HEAT functions, The SLEEP function is used to decrease

FAN
TIMER ,
measuring ambient temperature from OFF energy use while you sleep (and don t need
the remote control (instead of from the SLEEP FRESH
the same temperature settings to stay
indoor unit itself) will enable the air comfortable). This function can only be
conditioner to optimize the temperature
SELF
TURBO CLEAN LED FOLLOW
ME activated via remote control.
around you and ensure maximum comfort.
1. Press FOLLOW ME button to activate Note: The SLEEP function is not available
function. The remote control will send in FAN or DRY mode.
temperature signal to the indoor unit
every three minutes.
2. Press FOLLOW ME button again to
turn off this function.
MODEL:RG57A8/BGCEF

13