GIANI ZAIL SINGH CAMPUS COLLEGE

OF
ENGINEERING & TECHNOLOGY
BATHINDA

NOTICE, CSE Department (Training Report)

INSTRUCTIONS FOR TRAINING REPORT SUBMISSION BY B. TECH (CSE 3rd, 5th, &
7thSEM ) STUDENTS

All students (B.Tech. CSE 3rd,5th& 7thsem) are required to submit their training report as per
Date announced by HOD of CSE Deptt. The seminar and viva of the training report will be held
on that particular date. Students are advised to follow a prescribed sequential format for writing
training reports given below:
1. The sequence in which the training report material should be arranged and boundshould
be asfollows:
i. Cover page (sample copy attached as annexure-A).
ii. Title page (sample copy attached as annexure-B).
iii. Certificate by company (if any)
iv. Preface (sample copy attached as annexure-C)
v. Acknowledgment (sample copy attached as annexure-D)
vi. Candidate Declaration (sample copy attached as annexure-E)
vii. Contents with title & subtitle, page no. (Breakup of sections according to
explanation is advised).
viii. List of Figures
ix. List of Tables
x. Notations/nomenclature (if any)
xi. Executive summary (with Chapters &sections)
xii. Appendix / Annexure/Data sheets( if any)

2. For text in the of the report a proper format must be followed

i.e.
Chapter heading : 16 font-Times New Roman-Bold
Section heading :14 font-Times New Roman-Bold
Rest of the text :12 font-Times New Roman
Line spacing : 1.5
3. There should be Separator sheets between the chapters
mentioning chapter no. & the title & should also carry one
transparency with each separator sheet.
4. The report must consist of following chapters
 Chapter 1- Introduction
 Chapter 2- Project work (It can span in two or three subchapters
depending on type & volume of work. This contains the text & related to
hardware & software implementation. This section should follow the
software engineering approach)
  Chapter 3- Results and Discussion
 Chapter 4 Conclusions and future scope

5. Numbering of pages upto List of tables should be in (ROMAN -8 font) and the text,
beginning with the Introduction, or of Chapter 1, should be numbered
consecutively with Arabic numerals. Page numbers must be placed 1.5cm from the
bottom center of eachpage.
6. Numbering of Tables, Figures and Illustrations must be done sequentially, including the
Chapter number in which it is placed (for example, Figure 2.1, 3.2,etc).
7. Captions for Figures, Tables and Illustrations must be placed at the bottom of each, and
centered.
8. Text should be properly adjusted, justified and aligned at required positions.
9. One reports per student need to be submitted (Spiral binded).
10. Cover of Hard bounded should be with Front Page black and with golden color font(If
Instructed for final viva).
11. Students are advised to prepare a 8 min. power point presentation
12. A CD inculcating soft copy of the report and power point presentation along with the
project needs to be submitted as well at the time ofviva.
13. Training viva will be awarded as per the following criterion
i. Timely submission of report in proper format -10%
ii. Ability to express – 10%
iii. Knowledge –30%
iv. Presentation/ Daily Diary -30%
v. Questions/viva -20%

Er. Manpreet Kaur Sidhu Dr. Dinesh kumar

Training &Placement Incharge (HOD, CSEDeptt.)
(AnnexureA)* (CoverPage)*

TRAINING REPORT
(16 Normal Arial)

On
(14 Arial)

NAME OF TOPIC
(20 Arial)

Submitted to MAHARAJA RANJIT SINGH PUNJAB TECHNICAL

UNIVERSITY in partial fulfillment of the requirement for the award of the
degree of
(14 Arial)

B.TECH
(18 Arial)
in
(14 Arial)
COMPUTER SCIENCE & ENGINEERING
16 Arial)

Submitted By
NAME OF THE STUDENT
Roll.No.
(16 Arial)

DEPARTMENT OF COMPUTER SCIENCE & ENGINEERING

(14 Times New Roman)
GIANI ZAIL SINGH CAMPUS COLLEGE OF ENGINEERING&
TECHNOLOGY, MRSPTU, BATHINDA-151001
(1stletter 20, rest 14 Times NewRoman)-Bold
JULY 2019
(AnnexureB)* (TitlePage)*
TRAINING REPORT
(16 Normal Arial)

On
(14 Arial)
NAME OF TOPIC
(20 Arial)

Submitted to MAHARAJA RANJIT SINGH PUNJAB TECHNICAL

UNIVERSITY in partial fulfillment of the requirement for the award of the
degree of
(14 Arial)

B.TECH
(18 Arial)
in
(14 Arial)
COMPUTER SCIENCE & ENGINEERING
(16 Arial)

Submitted By
NAME OF THE STUDENT
Roll.No.
(16 Arial)

DEPARTMENT OF COMPUTER SCIENCE & ENGINEERING

(14 Times New Roman)
GIANI ZAIL SINGH CAMPUS COLLEGE OF ENGINEERING &
TECHNOLOGY, MRSPTU, BATHINDA-151001
( 1stletter 20, rest 14 Times New Roman)-Bold
JULY 2019
(Annexure -C)*

PREFACE
Training is an integral part of B.Tech and each and every student has to undergo the training for
_____weeks in a company.

This record is concerned about our practical training during the ____semester of our B.Tech. We
have taken our Practical training in …………………………… During this training, we got to
learn many new things about the industry and the current requirements of companies. This
training proved to be a milestone in our knowledge of present industry. Every say and every
moment was an experience in itself, an experience which theoretical study can’t provide.
(Annexure -D)*

ACKNOWLEDGEMENT
It is my pleasure to be indebted to various people, who directly or indirectly contributed in the
development of this work and who influenced my thinking, behavior and acts during the course
of study.

I express my sincere gratitude to Dr. Dinesh kumar worthy HOD and Er. Naresh Garg and Er.
Manpreet Kaur, Training & Placement In-charge for providing me an opportunity to undergo
summer training at……………..

I am thankful to ……………......... for his support, cooperation, and motivation provided to me

during the training for constant inspiration, presence and blessings.

I also extend my sincere appreciation to …………………………who provided his valuable

suggestions and precious time in accomplishing my training report.(if you want to thank
someone else)

Lastly, I would like to thank the almighty and my parents for their moral support and my friends
with whom I shared my day-to-day experience and received lots of suggestions that my quality
of work.

Name of student
(Annexure –E )*

CANDIDATE’S DECLARATION

I, ……NAME………., Roll No. …………, B.Tech (Semester- III / V / VII) of the Gaini Zail
Singh Campus College of Engineering & Technology, Bathinda hereby declare that the
Training Report entitled “……………TITLE…………………..” is an original work and data
provided in the study is authentic to the best of my knowledge. This report has not been
submitted to any other Institute for the award of any other degree.

Name of Student
(Roll No.…………)

Place:
Date:
Text marked with a star(*) on the top of pages is only for information purpose, do not print it on
actual pages.