wall-mounted
Tool Shelf 
Materials List
A Ends (2) 3/ x 6 - 14 L Large Drawer Sides (4) 1/  x 27/  - 51/
4 2 16 4
B Top Shelf/Bottom (2) 1/  x 53/  - 24 M Large Drawer Fronts/Backs (4) 1/  x 27/  - 413/
2 4 2 16 16
C Dividers (2) 1/  x 53/  - 43/ N Drawer Bottoms (4) 45/16 x 51/4 - 1/4 Ply.
2 4 4
D Drawer Shelves (2) 1/  x 53/  - 51/
2 4 8
E Cleat (1) 3/ x 21/  - 243/
4 4 4 • (12) #6 x 11/2" Fh Woodscrews
F Back (1) 121/4 x 243/4 - 1/4 Ply. • (3) #8 x 2" Fh Woodscrews
G Rear Tool Rail (1) 1/  x 1 - 23 3/
2 4 • (4) #8 x 3/4" Fh Woodscrews
H Front Tool Rail (1) 1/  x 1/  - 233/
2 2 4 • (12) 3/8"-dia. Wood Plugs
I Spacers (12) 1/  x 1/  - 1
2 2 • (4) 1/2"-dia. Brass Knobs (Bronze Finish)
 J Small Drawer Sides (4) 1/  x 17/  - 51/
2 16 4
K Small Drawer Fronts/Backs (4) 1/  x 17/  - 413/
2 16 16

Cutting Diagram
#/4" x 6" - 60" (2.5 Bd. Ft.)
E
A A

!/2" x 6" - 96" (4.0 Sq. Ft.) I G   H

B B C C D D

!/2" x 5" - 48" (1.7 Sq. Ft.) NOTE: CUT SPACERS (I)
J J J J K K K K TO LENGTH
AFTER SHAPING
L L L L M M M M

!/4" x 24" - 48" PLYWOOD

N N N N

ShopNotes No. 121 Page 1 of 1 ©2012 August Home Publishing. All rights reserved.
 

  infill
Smoothing Plane
Save time and
effort with these
patterns for
making the steel
sides and the
hardwood tote
and cheeks.

All of the parts for the infill Side Pattern. To make the steel Rear Infill. You’ll only need one
smoothing plane from ShopNotes sides, I printed two copies of the pattern to cut out and shape the
121 feature curves or irregular pattern below. One is used to tote. When making the cheeks,
shapes. You can eliminate quite a make a hardboard template. And keep in mind that they end up as
 bit of layout time by using the full- the other is used as a guide for mirror images. So the pattern is
size patterns on these two pages. drilling all the holes. only used to cut the final shape.

SIDE PATTERN (SHOWN ACTUAL SIZE) 1 SQUARE = !/4"

NOTE: ALL HOLES

ARE %/32" DIA.

FACTORY EDGE S

ShopNotes No. 121 Page 1 of 2 ©2011 August Home Publishing. All rights reserved.
 

 TOTE PATTERN (SHOWN ACTUAL SIZE) 1 SQUARE = !/4"

NOTE: CUT FINAL

BED ANGLE
AFTER GLUING
CHEEKS TO TOTE

WASTE

TOTE

   

CHEEK PATTERN (SHOWN ACTUAL SIZE) 1 SQUARE = !/4"

WASTE

CHEEK

ShopNotes No. 121 Page 2 of 2 ©2011 August Home Publishing. All rights reserved.