EASTRON SDM630MV CT User Manual

SDM630MV CT
Din Rail Smart Energy Meter for Single and Three Phase Electrical Systems

 Measures kWh Kvarh, KW, Kvar, KVA, P,

F, PF, Hz, dmd, V, A, THD,etc.
 Bi-directional measurement IMP & EXP
 Two pulse outputs
 RS485 Modbus
 Din rail mounting 35mm
 0.33V CT connection
 Better than Class 1 / B accuracy

USER MANUAL
2016 V3.5
JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.
TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -1-
EASTRON SDM630MV CT User Manual

1. Introduction
This document provides operating, maintenance and installation instructions. The unit measures
and displays the characteristics of three phase four wires(3p4w) supplies, including voltage,
frequency, current, power ,active and reactive energy, imported or exported. Energy is measured
in terms of kWh, kVArh. Maximum demand current can be measured over preset periods of up to
60minutes. In order to measure energy, the unit requires voltage and current inputs in addition to
the supply required to power the product. The requisite current input(s) are obtained via current
transformers(CT).

This meter can be configured to work with a wide range of CTs with 0.33V output, giving the unit
a wide range of operation. Built-in interfaces provides pulse and RS485 Modbus RTU outputs.
Configuration is password protected.

This unit can be powered from a separate auxiliary(AC or DC)supply. Alternatively it can be
powered from the monitored supply, where appropriate.

1.1 Unit Characteristics

The Unit can measure and display:
 Line voltage and THD% (total harmonic distortion) of all phases
 Line Frequency
 Currents, Current demands and current THD% of all phases
 Power, maximum power demand and power factor
 Active energy imported and exported
 Reactive energy imported and exported

The unit has password-protected set-up screens for:

 Changing password
 Demand Interval time
 Reset for demand measurements
 Pulse output duration

Two pulse output indicates real-time energy measurement. An RS485 output allows remote
monitoring from another display or a computer.

1.2 Current Transformer Primary Current

The unit can be configured to operate with CT with 0.33V output. The secondary CT is fixed 0.33V,
and the primary is optional.

1.3 RS485 Serial – Modbus RTU

This uses an RS485 serial port with Modbus RTU protocol to provide a means of remotely
monitoring and controlling the Unit
Set-up screens are provided for setting up the RS485 port. Refers to section 4.8

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -2-
EASTRON SDM630MV CT User Manual

1.4 Pulse output

This provides two pulse outputs that clock up measured active and reactive energy. The constant
for reactive energy is 3200imp/kVArh. The pulse width for active energy can be set from the
set-up menu.

2. Start Up Screens
The first screen lights up all display segments and
can be used as a display check.

The second screen indicates the firmware

installed in the unit and its build number.

The interface performs a self-test and

indicates the result if the test passes.

After a short delay, the screen will display active energy measurements.

3. Measurements
The buttons operate as follows:
Selects the Voltage and Current display screens
In Set-up Mode, this is the “Left” or “Back” button.

Select the Frequency and Power factor display screens

In Set-up Mode, this is the “Up” button

Select the Power display screens

In Set-up Mode, this is the “Down” button

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -3-
EASTRON SDM630MV CT User Manual

Select the Energy display screens

In Set-up mode, this is the “Enter” or “Right” button

3.1 Voltage and Current

Each successive pressing of the button selects a new range:

Phase to neutral voltages

Current on each phase

Phase to neutral voltage THD%

Current THD% for each phase

3.2 Frequency and Power factor and Demand

Each successive pressing of the button selects a new range:

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -4-
EASTRON SDM630MV CT User Manual

Frequency and Power Factor (total)

Power Factor of each phase

Maximum Power Demand

Maximum Current Demand

3.3 Power

Each successive pressing of the button select a new range:

Instantaneous Active Power in kW

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -5-
EASTRON SDM630MV CT User Manual

Instantaneous Reactive Power in kVAr

Instantaneous Volt-amps in KVA

Total kW, kVArh, kVA

3.4 Energy Measurements

Each successive pressing of the button selects a new range:

Imported active energy in kWh

Exported active energy in kWh

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -6-
EASTRON SDM630MV CT User Manual

Imported reactive energy in kVArh

Exported reactive energy in kVArh

Total active energy in kWh

Total reactive energy in kVAh

4. Setting Up

To enter set-up mode, pressing the button for 3 seconds, until the password screen
appears.

Setting up is password-protected so you must enter the correct password (default ‘1000’) before
processing. If an incorrect password is entered, the display will show: PASS Err

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -7-
EASTRON SDM630MV CT User Manual

To exit setting-up mode, press repeatedly until the measurement screen is restored.

4.1 Set-up Entry Methods

Some menu items, such as password and CT, require a four-digit number entry while others, such
as supply system, require selection from a number of menu options.

4.1.1 Menu Option Selection

1) Use the and buttons to select the required item from the menu. selection
does not roll over between bottom and top of list

2) Press to confirm your selection

3) If an item flashes, then it can be adjusted by the and buttons. If not, there
maybe a further layer.

4) Having selected an option from the current layer, press to confirm your selection.
The SET indicator will appear.

5) Having completed a parameter setting, press to return to a higher menu level. The

SET indicator will be removed and you will be able to use the and buttons for
further menu selection.

6) On completion of all setting-up, press repeatedly until the measurement screen is

restored.

4.1.2 Number Entry Procedure

When Setting up the unit, some screens require the entering of a number. In particular, on entry
to the setting up section, a password must be entered. Digits are set individually, from left to
right. The procedure is as follows:

1) The current digit to be set flashes and is set using the and buttons

2) Press to confirm each digit setting. The SET indicator appears after the last digit has
JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.
TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -8-
EASTRON SDM630MV CT User Manual

been set.

3) After setting the last digit, press to exit the number setting routine. The SET indicator
will be removed.

4.2 Change password

Use the and to choose the

change password option

Press the to enter the change password

routine. The new password screen will appear
with the first digit flashing

Use and to set the first digit

and press to confirm your selection. The

next digit will flash.

Repeat the procedure for the remaining three

digits

After setting the last digit, SET will show.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. -9-
EASTRON SDM630MV CT User Manual

Press to exit the number setting routine and return to the Set-up menu.

4.3 DIT Demand Integration Time

This sets the period in minutes over which the current and power readings are integrated for
maximum demand measurement. The options are: off, 5, 10, 15 30,60 minutes

From the set-up menu, use and

buttons to select the DIT option. The screen will
show the currently selected integration time.

Press to enter the selection routine. The

current time interval will flash

Use and buttons to select the

time required.

Press to confirm the selection. SET

indicator will appear.

Press to exit the DIT selection routine and return to the menu.

4.4 CT
The CT option sets the primary current(CT2 fixed 0.333V) of the current transformer (CT) that
wires to the meter.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 10 -
EASTRON SDM630MV CT User Manual

From the Set-up menu, use and

buttons to select the CT primary(CT1).

Its’ default 5A,and ranged from 0005 to 9999

Secondary CT(CT2)
It’s fixed 0.333V, and can not be set.

4.5 PT
The PT option sets the secondary voltage (PT2 100 to 500V) of the Voltage transformer (PT) that
wires to the meter.

From the Set-up menu, use and

buttons to select the PT option. The

screen will show the voltage PT secondary voltage
value. The default value is 400V

Secondary PT setting

Press to enter the PT secondary voltage

selection routine. The range is from 100 to 500V

Set PT ratios value

Press to enter the PT ratio screen.

The range is from 0001 to 9999

For example, if set the ratio to be 100,it means the primary voltage equals secondary voltage
x100

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 11 -
EASTRON SDM630MV CT User Manual

4.6 Pulse output

This option allows you to configure the pulse output. The output can be set to provide a pulse for
a defined amount of energy active or reactive.

Use this section to set up the relay pulse output—Units: kWh, kVArh

From the Set-up menu, use and

buttons to select the Pulse output

option.

Press to enter the selection routine. The

unit symbol will flash.

Use and buttons to choose

kWh or kVArh.

On completion of the entry procedure, press to confirm the setting and press

to return to the main set up menu.

4.6.1 Pulse rate

Use this to set the energy represented by each pulse. Rate can be set to 1 pulse per
0.01kWh/0.1kWh/1kWh/10kWh/100kWh.

(It shows 1 impulse = 10kWh/kVArh)

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 12 -
EASTRON SDM630MV CT User Manual

From the Set-up menu, use and

buttons to select the Pulse Rate option.

Press to enter the selection routine. The

current setting will flash.
0.01/0.1/1/10/100kWh/kVArh per pulse

Use and buttons to choose pulse rate. On Completion of the entry procedure,

press to confirm the setting and press to return to the main set up menu.

4.6.2 Pulse Duration

The energy monitored can be active or reactive and the pulse width can be selected as 200, 100
or 60ms.

(It shows pulse width of 200ms)

From the Set-up menu, use and

buttons to select the Pulse width option.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 13 -
EASTRON SDM630MV CT User Manual

Press to enter the selection routine. The

current setting will flash.

Use and buttons to choose pulse width. On Completion of the entry procedure,

press to confirm the setting and press to return to the main set up menu.

4.7 Communication
There is a RS485 port can be used for communication using Modbus RTU protocol. For Modbus
RTU, parameters are selected from Front panel.

4.7.1 RS485 Address

(The range is from 001 to 247)

From the Set-up menu, use and

buttons to select the Address ID

Press button to enter the selection

routine. The current setting will be flashing.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 14 -
EASTRON SDM630MV CT User Manual

Use and buttons to choose

Modbus Address(001 to 247)

On completion of the entry procedure, press button to confirm the setting and press

button to return the main set-up menu.

4.7.2 Baud Rate

From the Set-up menu, use and

buttons to select the Baud Rate option.

Press to enter the selection routine. The

current setting will flash.

Use and buttons to choose

Baud rate 2.4k. 4.8k, 9.6k, 19.2k, 38.4k

On Completion of the entry procedure, press to confirm the setting and press

to return to the main set up menu.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 15 -
EASTRON SDM630MV CT User Manual

4.7.3 Parity

From the Set-up menu, use and

buttons to select the Parity option.

Press to enter the selection routine. The

current setting will flash.

Use and buttons to choose

Parity (EVEN / ODD / NONE)

On completion of the entry procedure, press to confirm the setting and press

to return to the main set up menu.

4.7.4 Stop bits

From the Set-up menu, use and

buttons to select the Stop Bit option.

Press to enter the selection routine. The

current setting will flash.

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 16 -
EASTRON SDM630MV CT User Manual

Use and buttons to choose

Stop Bit (2 or 1)

On completion of the entry procedure, press to confirm the setting and press

to return to the main set up menu.

4.8 CLR
The meter provides a function to reset the maximum demand value of current and power.

From the Set-up menu, use and

buttons to select the reset option.

Press to enter the selection routine. The

dIt will flash.

Press to confirm the setting and press to return to the main set up menu.

5 Specifications
5.1 Measured Parameters
The unit can monitor and display the following parameters of four phase four wire(3p4w) supply.

5.1.1 Voltage and Current

Phase to neutral voltages 100 to 289V a.c.
Voltages between phases 173 to 500V a.c.
Percentage total voltage harmonic distortion (THD%) for each phase to N
Percentage voltage THD% between phases
Current THD% for each phase

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 17 -
EASTRON SDM630MV CT User Manual

5.1.2 Power factor and Frequency and Max. Demand

Frequency in Hz
Instantaneous power:
 Power 0 to 3600 MW
 Reactive Power 0 to 3600 MVAr
 Volt-amps 0 to 3600 MVA
Maximum demanded power since last Demand reset Power factor
Maximum neutral demand current, since the last Demand reset (for three phase supplies only)

5.1.3 Energy Measurements

 Imported active energy 0 to 9999999.9 kWh
 Exported active energy 0 to 9999999.9 kWh
 Imported reactive energy 0 to 9999999.9 kVArh
 Exported reactive energy 0 to 9999999.9 kVArh
 Total active energy 0 to 9999999.9 kWh
 Total reactive energy 0 to 9999999.9 kVArh

5.2 Measured Inputs

Voltage inputs through 4-way fixed connector with 2.5mm² stranded wire capacity. four phase
four wire(3p4w) unbalanced. Line frequency measured from L1 voltage or L3 voltage.
Three current inputs (six physical terminals) with 2.5mm² stranded wire capacity for connection
of external CTs. Nominal rated input current 5A or 1A a.c. Rms.

5.3 Accuracy
 Voltage 0·5% of range maximum
 Current 0·5% of nominal
 Frequency 0·2% of mid-frequency
 Power factor 1% of unity (0.01)
 Active power (W) ±1% of range maximum
 Reactive power (VAr) ±2% of range maximum
 Apparent power (VA) ±1% of range maximum
 Active energy (Wh) Class 1 IEC 62053-21
 Reactive energy (VARh) ±2% of range maximum
 Total harmonic distortion 1% up to 31st harmonic

5.4 Auxiliary Supply

Two-way fixed connector with 2·5mm2 stranded wire capacity.
85 to 275V a.c. 50/60Hz ±10% or 120V to 380V d.c. ±20%. Consumption < 10W.
5.5 Interfaces for External Monitoring
Three interfaces are provided:
 an RS485 communication channel that can be programmed for Modbus RTU protocol
 an relay output indicating real-time measured energy.(configurable)

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 18 -
EASTRON SDM630MV CT User Manual

 an pulse output 3200imp/kWh (not configurable)

The Modbus configuration (Baud rate etc.) and the pulse relay output assignments (kW/kVArh,
import/export etc.) are configured through the Set-up screens.

5.5.1 Pulse Output

The pulse output can be set to generate pulses to represent kWh or kVArh.
Rate can be set to generate 1 pulse per:
0.01 = 10 Wh/VArh
0.1 = 100 Wh/VArh
1 = 1 kWh/kVArh
10 = 10 kWh/kVArh
100 = 100 kWh/kVArh
Pulse width 200/100/60 ms.
Relay Rating 240V ac 50mA

5.5.2 RS485 Output for Modbus RTU

For Modbus RTU, the following RS485 communication parameters can be configured from the
Set-up menu:
Baud rate 2400, 4800, 9600, 19200, 38400
Parity none(default)/odd/even
Stop bits 1 or 2
RS485 network address nnn – 3-digit number, 1 to 247
Modbus™ Word order Hi/Lo byte order is set automatically to normal or reverse. It cannot
be configured from the set-up menu.

5.6 Reference Conditions of Influence Quantities

Influence Quantities are variables that affect measurement errors to a minor degree. Accuracy is
verified under nominal value (within the specified tolerance) of these conditions.
 Ambient temperature 23°C ±1°C
 Input waveform 50 or 60Hz ±2%
 Input waveform Sinusoidal (distortion factor < 0·005)
 Auxiliary supply voltage Nominal ±1%
 Auxiliary supply frequency Nominal ±1%
 Auxiliary supply waveform (if AC) Sinusoidal (distortion factor < 0·05)
 Magnetic field of external origin Terrestrial flux

5.7 Environment
 Operating temperature -25°C to +55°C*
 Storage temperature -40°C to +70°C*
 Relative humidity 0 to 90%, non-condensing
 Altitude Up to 2000m
 Warm up time 1 minute

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 19 -
EASTRON SDM630MV CT User Manual

 Vibration 10Hz to 50Hz, IEC 60068-2-6, 2g

 Shock 30g in 3 planes
*Maximum operating and storage temperatures are in the context of typical daily and seasonal
variation.

5.8 Mechanics
 DIN rail dimensions 72 x 94.5 mm (WxH) per DIN 43880
 Mounting DIN rail (DIN 43880)
 Sealing IP20 (minimum)
 Material Self-extinguishing UL94 V_0

6 Dimensions

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 20 -
EASTRON SDM630MV CT User Manual

7 Installation

JIAXING EASTRON ELECTRONIC INSTRUMENTS CO.,LTD.

TEL:0086-573-83698881/83698882 FAX: 0086-573-83698883
Web: www.eastrongroup.com Email: [email protected]
Add: No.1369. Chengnan Road, Nanhu District, Jiaxing City, Zhejiang, China 314001. - 21 -