100% found this document useful (1 vote)

248 views397 pages

1.6 66 77 2.0 105 110 135 KW TDI CR Engine

Uploaded by

RST

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

100% found this document useful (1 vote)

248 views397 pages

1.6 66 77 2.0 105 110 135 KW TDI CR Engine

Uploaded by

RST

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 397

Service

Workshop Manual
Octavia III 2013 ➤
Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine
Engine ID
CLH CLH CKF CKF CRV CUP CRK
A B B C C A B
Edition 10.2013

Service Department. Technical Information

Service
List of Workshop Manual Repair GroupsList of Workshop Manual
Repair GroupsList of Workshop Manual Repair Groups

Repair Group
00 - Technical data
01 - Self-diagnosis
10 - Removing and installing engine
13 - Crankshaft group
15 - Cylinder head, valve gear
17 - Lubrication
19 - Cooling
20 - Fuel supply system
21 - Turbocharging/supercharging
23 - Mixture preparation - injection
26 - Exhaust system
28 - Glow plug system

Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.

All rights reserved.

No reproduction without prior agreement from publisher.

Copyright © 2013 ŠKODA AUTO a. s. D4B802C6D8D

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Contents

00 - Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Engine number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Engine characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

01 - Self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Self diagnosis, safety measures, cleanliness regulations and directions . . . . . . . . . . . . . . 3
1.1 Self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Supplementary instructions and assembly work on vehicles with an air conditioning
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Safety precautions when working on fuel supply system . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Safety measures for working on vehicles with start/stop system . . . . . . . . . . . . . . . . . . . . 6
1.5 Regulations concerning cleanliness when working on the fuel supply/fuel injection system
........................................................................ 6
1.6 Regulations concerning cleanliness when working on the exhaust gas turbocharger . . . . 7
1.7 General instructions for charge air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

10 - Removing and installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1 Removing and installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Removing and installing engine trim panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 Removing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 Securing the engine to the assembly stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.4 Installing engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2 Assembly bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.1 Assembly overview - assembly mountings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.2 Support the engine in its installed position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3 Removing and installing engine mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.4 Removing and installing engine support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.5 Removing and installing pendulum support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.6 Checking and adjusting the assembly bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

13 - Crankshaft group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1 Removing and installing a V-ribbed belt and a toothed belt . . . . . . . . . . . . . . . . . . . . . . . . 35
1.1 unlessV-ribbed belt - Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
35
1.2 withRemoving and installing
respect to the correctness polyin this
of information V-belt . . Copyright
document. . . . . . by
. .ŠKODA
. . . . AUTO
. . . .A..S.�
........................ 36
1.3 Removing and installing crankshaft-belt pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1.4 Removing and installing tensioning device for V-ribbed belt . . . . . . . . . . . . . . . . . . . . . . . . 38
1.5 Removing and installing bracket for auxiliary units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
1.6 Summary of components - toothed belt guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
1.7 Assembly overview - toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
1.8 Removing and installing top toothed belt guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
1.9 Removing and installing bottom toothed belt guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
1.10 Remove the toothed belt from the camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
1.11 Removing and installing toothed belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2 Removing and installing sealing flange and flywheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
2.1 Summary of components - sealing flange belt pulley side . . . . . . . . . . . . . . . . . . . . . . . . . . 59
2.2 Removing and installing the sealing flange on the belt pulley side . . . . . . . . . . . . . . . . . . 60
2.3 Summary of components - gearbox side summary of components and flywheel . . . . . . . . 61
2.4 Removing and installing sealing flange on gearbox side . . . . . . . . . . . . . . . . . . . . . . . . . . 63
2.5 Removing and installing flywheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3 Crankshaft, Piston and Conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.1 Summary of components - crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.2 Replace the needle bearing in the crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Contents i
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3.3 Assembly overview - piston and conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

3.4 Removing and installing the piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3.5 Checking piston projection in TDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
3.6 Separating new conrod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

15 - Cylinder head, valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

1 Removing and installing cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1.1 Assembly overview - cylinder head cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1.2 Removing and installing cylinder head cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
1.3 Replacing gasket rings for injection units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
1.4 Assembly overview - cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
1.5 Removing and installing cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
1.6 Checking compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
2 Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
2.1 Assembly overview - valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
2.2 Replacing camshaft gasket ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
2.3 Removing and installing camshaft control valve 1 N205 . . . . . . . . . . . . . . . . . . . . . . . . . . 102
2.4 Removing and installing camshaft control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
2.5 Removing and installing camshaft housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
2.6 Checking hydraulic balancing elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
2.7 Removing and installing valve stem seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
2.8 Valve dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
2.9 Checking valve guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

17 - Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
1 Removing and installing parts of the lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . 116
1.1 Summary of components - removing and installing parts of the lubrication system . . . . . . 116
1.2 Removing and installing oil level and oil temperature sender G266 . . . . . . . . . . . . . . . . . . 118
1.3 Summary of components - oil filter holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
1.4 Removing and installing the oil filter holder with the engine oil cooler . . . . . . . . . . . . . . . . 121
1.5 Removing and installing oil sump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
1.6 Removing and installing oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
1.7 Removing and installing oil pressure switch F1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
1.8 Removing and installing oil pressure switch for reduced oil pressure F378 . . . . . . . . . . . . 128
1.9 Removing and installing valve for oil pressure control N428 . . . . . . . . . . . . . . . . . . . . . . . . 129
1.10 Testing oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

19 - Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
1 Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
1.1 Coolant hose schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
1.2 Coolant hose schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
1.3 Coolant hose schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
1.4 Draining and filling coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
1.5 Checking cooling system for leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
2 Coolant pump and coolant regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
2.1 Summary of components - coolant pump and coolant thermostat . . . . . . . . . . . . . . . . . . . . 147
2.2 Summary of components - coolant temperature sender . . . . . . . . . . . . . . . . . . . . . . . . . . 148
2.3 Summary of components - electric coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
2.4ProtectedRemoving and installing coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
149
2.5 Removing
unless authorised andAUTO
by ŠKODA installing thermostat
A. S. ŠKODA . .not
AUTO A. S. does . .guarantee
. . . . . or. .accept
. . . any
. . liability
.......................... 150
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
2.6 Removing and installing coolant valve for cylinder head N489 . . . . . . . . . . . . . . . . . . . . . . 151
2.7 Testing coolant thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
2.8 Removing and installing coolant temperature sender G62 . . . . . . . . . . . . . . . . . . . . . . . . 152
2.9 Removing and installing charge air cooler pump V188 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
2.10 Removing and installing the heating backup pump V488 . . . . . . . . . . . . . . . . . . . . . . . . . . 154

ii Contents
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 Coolant pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

3.1 Summary of components - coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
3.2 Removing and installing the front top coolant pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
3.3 Removing and installing the front bottom coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
3.4 Removing and installing the front left coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
3.5 Removing and installing the front right coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
3.6 Remove and install the left coolant pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
3.7 Removing and installing the rear coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
3.8 Removing and installing the rear right coolant pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
4 Radiator and radiator fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
4.1 Parts of the cooling system fitted to body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
4.2 Summary of components - fan shroud and radiator fan V7 . . . . . . . . . . . . . . . . . . . . . . . . 172
4.3 Summary of components- fan shroud and radiator fan V7 and radiator fan 2 V177 . . . . . . 173
4.4 Removing and installing radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
4.5 Removing and installing fan shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
4.6 Removing and installing radiator fans V7 and V177 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

20 - Fuel supply system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

1 Measures in case of misfuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
1.1 Step 1, engine started with incorrect fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
1.2 Step 2, the engine was not started with incorrect fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
1.3 Step 3, metal swarfs are present in the
unless fuel bydelivery
authorised ŠKODA AUTO unitA.and the AUTO
S. ŠKODA fuel A.tank
S. does. not
. .guarantee
. . . . .or. accept
. . . any
182liability
1.4 Step 4, no metal swarfs are present in the fuel delivery unit and the fuel tank . . . . . . . . . . 183
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1.5 Step 5, metal swarfs are present in the high pressure pump . . . . . . . . . . . . . . . . . . . . . . . . 184
1.6 Step 6: no metal swarfs are present in the high pressure pump . . . . . . . . . . . . . . . . . . . . 184
2 Removing and installing parts of the fuel supply system . . . . . . . . . . . . . . . . . . . . . . . . . . 185
2.1 Fuel tank with attached parts, vehicles with front-wheel drive - Summary of components
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
2.2 Fuel tank with attached parts, vehicles with four-wheel drive - Summary of components . . 189
2.3 Fuel delivery unit, vehicles with front-wheel drive - Summary of components . . . . . . . . . . 192
2.4 Fuel delivery unit, vehicles with four-wheel drive - Summary of components . . . . . . . . . . 194
2.5 Fuel filter - Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
2.6 Drain fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
2.7 Removing and installing fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
2.8 Fuel hoses in the engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
2.9 Extract fuel from the fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
2.10 Removing and installing the fuel delivery unit, vehicles with front-wheel drive . . . . . . . . . . 210
2.11 Removing and installing the fuel delivery unit, vehicles with four-wheel drive . . . . . . . . . . 214
2.12 Removing and installing misfuelling protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
2.13 Deactivate misfuelling protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
2.14 Removing and installing the sender for fuel gauge display G . . . . . . . . . . . . . . . . . . . . . . 223
2.15 Removing and installing fuel gauge sender 2 G169 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
2.16 Separating push-on couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
2.17 Removing and installing the fuel delivery unit, vehicles with front-wheel drive . . . . . . . . . . 230
2.18 Removing and installing the fuel delivery unit, vehicles with four-wheel drive . . . . . . . . . . 236
2.19 Removing and installing fuel pump control unit J538 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
2.20 Check the suction jet pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
2.21 Removing and installing suction jet pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
2.22 Inspecting uel pump G6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
2.23 Check sender for fuel gauge display G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
3 Accelerator mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
3.1 Assembly overview - accelerator module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
3.2 Removing and installing accelerator module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263

21 - Turbocharging/supercharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

Contents iii
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 Charge-air system - exhaust gas turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

1.1 Exhaust gas turbocharger with component parts - Summary of components . . . . . . . . . . 265
1.2 Removing and installing exhaust gas turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
1.3 Removing and installing exhaust gas turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
1.4 Replace vacuum positioning element for charge pressure regulation with position sender for
charge pressure regulator G581 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
1.5 Connection diagram for vacuum hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
1.6 Checking vacuum system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
1.7 Hose connections with screw clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
2 Charge-air system - radiator, leaktightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
2.1 Charge air cooling - Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
2.2 Removing and installing the charge pressure sender G31 . . . . . . . . . . . . . . . . . . . . . . . . 283
2.3 Checking the charge-air system for leaktightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284

23 - Mixture preparation - injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287

1 Diesel direct injection system - fitting location, system overview . . . . . . . . . . . . . . . . . . . . 287
1.1 Installation location overview - fuel injection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
1.2 Schematic overview - fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
1.3 Filling/bleeding the fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
1.4 Check the fuel system for tightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
2 Injection units/fuel distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
2.1 Summary of components - injection units (injectors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
2.2 Fuel distributor - summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
2.3 Check injection units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
2.4 Adjust the correction values for injection units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
2.5 Check injection unit return quantity with engine running . . . . . . . . . . . . . . . . . . . . . . . . . . 298
2.6 Check injection unit return flow quantity at starter speed . . . . . . . . . . . . . . . . . . . . . . . . . . 300
2.7 Carry out the vacuum test of the injection units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
2.8 Removing and installing the injection units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
2.9 Removing and installing high pressure lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
2.10 Removing and installing the fuel distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
3 High pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
3.1 Summary of components - high pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
3.2 Removing and installing the high pressure pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
4 Senders and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
4.1 Removing and installing intake air temperature sender G42 / charge air temperature sender
after charge air cooler G811 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
4.2 Removing and installing fuel temperature sender G81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
4.3 Removing and installing air flow mass meter G70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
4.4 Check fuel pressure regulating valve N276 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
4.5 Replace fuel pressure regulating valve N276 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
4.6 Removing and installing fuel pressure sender G247 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
4.7 Removing and installing differential pressure sender G505 . . . . . . . . . . . . . . . . . . . . . . . . 319
4.8 Removing and installing pressure sensor for exhaust gas 1 G450 . . . . . . . . . . . . . . . . . . 320
5 Lambda probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
5.1 Lambda probe - Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
5.2 Removing and installing Lambda probe G39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
5.3 Removing and installing Lambda probe after catalytic converter G130 . . . . . . . . . . . . . . 323
6 Intake manifold, air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
6.1 Assembly overview
unless authorised by ŠKODA- AUTO
intake A. S.manifold
ŠKODA AUTO. A. . .S..does
. . .not. .guarantee
. . . . . or. .accept
. . . any
. . .liability
.................... 325
6.2 Removing and installing the throttle valve control unit J338 . . . . . . . . . . . . . . . . . . . . . . . .
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
327
6.3 Removing and installing intake manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
6.4 Summary of components - air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
6.5 Removing and installing air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
7 Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336

iv Contents
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

7.1 Removing and installing engine control unit J623 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336

7.2 Removing and installing engine control unit J623 , engine control unit with protective
housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
8 Engine noise speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
8.1 Removing and installing engine noise speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339

26 - Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340

1 Removing and installing exhaust pipes/silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
1.1 Summary of components - front, middle and rear silencer, vehicles with front-wheel drive
........................................................................ 340
1.2 Summary of components - front, middle and rear silencer, vehicles with front-wheel drive
........................................................................ 342
1.3 Summary of components - front, middle and rear silencer, vehicles with front-wheel drive
........................................................................ 344
1.4 Front, middle and rear silencer, vehicles with EU4 emission level . . . . . . . . . . . . . . . . . . . . 345
1.5 Summary of components - front, middle and rear silencer, vehicles with four-wheel drive
........................................................................ 347
1.6 Removing and installing exhaust pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
1.7 Removing and installing the exhaust flap control unit J883 . . . . . . . . . . . . . . . . . . . . . . . . 350
1.8 Removing and installing rear silencer, vehicles with front-wheel drive . . . . . . . . . . . . . . . . 351
1.9 Removing and installing rear silencer, vehicles with front-wheel drive . . . . . . . . . . . . . . . . 353
1.10 Removing and installing rear silencer, vehicles with four-wheel drive . . . . . . . . . . . . . . . . 354
1.11 Replacing middle or rear silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
1.12 Aligning exhaust system free of stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
1.13 Align exhaust tailpipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
1.14 Inspecting the exhaust system for leaktightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
2 Cleansing exhaust emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
2.1 Summary of components - exhaust gas cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
2.2 Summary of components - exhaust gas cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
2.3 Removing and installing exhaust gas cleaning module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
2.4 Removing and installing catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
3 Exhaust temperature regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
3.1 Summary of components - exhaust temperature regulation . . . . . . . . . . . . . . . . . . . . . . . . 370
3.2 Removing and installing the exhaust gas temperature sender 1 G235 . . . . . . . . . . . . . . . . 371
3.3 Remove and install exhaust gas temperature sender 3 G495 / exhaust gas temperature
sender 4 G648 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
3.4 Removing and installing the exhaust gas temperature sender 2 G448 . . . . . . . . . . . . . . . . 373
4 Exhaust gas recirculation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
4.1 Exhaust gas recirculation with radiator for exhaust gas recirculation - Summary of
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
4.2 Exhaust gas recirculation with radiator for exhaust gas recirculation - Summary of
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
4.3 Control motor for exhaust gas recirculation V338 - Summary of components . . . . . . . . . . 378
4.4 Removing and installing control motor for exhaust gas recirculation V338 . . . . . . . . . . . . 379
4.5 Removing and installing control motor 2 for exhaust gas recirculation V339 . . . . . . . . . . 379
4.6 Removing and installing radiator for exhaust gas recirculation . . . . . . . . . . . . . . . . . . . . . . 381
4.7 Removing and installing radiator for exhaust gas recirculation . . . . . . . . . . . . . . . . . . . . . . 383

28 - Glow plug system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385

1 Glow Plug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
1.1 Summary of components - preheating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
1.2 Removing and installing glow plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
1.3 Removing and installing automatic glow period control unit J179 . . . . . . . . . . . . . . . . . . . . 388
1.4 Removing and installing Hall sender G40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
1.5 Removing and installing engine speed sender G28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389

vi Contents
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

00 – Technical data
1 Technical data
(SRL000628; Edition 10.2013)

1.1 Engine number

The engine number (“engine identification characters” and “serial
number”) is located at the engine/gearbox joint -arrow-.
In addition, a sticker with the “engine identification characters”
and “serial number” is affixed to the timing belt guard.
The engine identification characters are also indicated on the ve‐
hicle data sticker.
♦ The engine identification characters have 4 digits starting with
the letter “C”.
♦ The first 3 digits of the engine identification characters refer to
the displacement and the mechanical construction of the en‐
gine. They are type-punched in the cylinder block including the
serial number.
♦ The 4th digit refers to the output and torque of the engine and
depends upon the
Protected by copyright. engine
Copying control
for private unit. purposes, in part or in whole, is not permitted
or commercial
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1.2 Engine characteristics

Edition 10.2013 version 4.0
Engine identification characters CLHB CLHA CKFB
Manufactured 05.13 ► 11.12 ► 11.12 ►
Exhaust limit values conforming to EU5 EU5 EU5
Displacement l 1.598 1.598 1.968
Output kW at rpm 66/2750…4800 77/3000…4000 105/3500…4000
Torque Nm at rpm 230/1400…2700 250/1500…2750 320/1750…3000
Bore ∅ mm 79.5 79.5 81.0
Stroke mm 80.5 80.5 95.5
Cylinder/valves per cylinder 4/4 4/4 4/4
Compression 16.2 16.2 16.2
Firing order 1-3-4-2 1-3-4-2 1-3-4-2
Catalytic converter yes yes yes
Exhaust gas recirculation with radiator yes yes yes
Turbocharging yes yes yes
Charge air cooler yes yes yes
Diesel particle filter yes yes yes
Balancing shafts no no no

Engine identification char‐ CKFC CRVC CUPA CRKB

acters
Manufactured 11.12 ► 05.13 ► 05.13 ► 11.13 ►
Exhaust limit values con‐ EU5 EU4 EU5 EU6
forming to
Displace‐ l 1.968 1.968 1.968 1.598
ment
Output kW at rpm 110/3500…4000 105/3500…4000 135/3500…4000 81/3250…4000

1. Technical data 1
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Engine identification char‐ CKFC CRVC CUPA CRKB

acters
Torque Nm at rpm 320/1750…3000 320/1750…3000 380/1750…3250 250/1500…3000
Bore ∅ mm 81.0 81.0 81.0 79.5
Stroke mm 95.5 95.5 95.5 80.5
Cylinder/valves per cylinder 4/4 4/4 4/4 4/4
Compression 16.2 16.2 16.2 16.2
Firing order 1-3-4-2 1-3-4-2 1-3-4-2 1-3-4-2
Catalytic converter yes yes yes yes
Exhaust gas recirculation yes yes yes yes
with radiator
Turbocharging yes yes yes yes
Charge air cooler yes yes yes yes
Diesel particle filter yes no yes yes
Balancing shafts no no yes no

2 Rep. gr.00 - Technical data

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

01 – Self-diagnosis
1 Self diagnosis, safety measures,
cleanliness regulations and direc‐
tions

1.1 Self-diagnosis
This Rep.-Gr. is deleted.
For this use the “Vehicle self-diagnosis”, “Measuring method” and
“Fault finding” ⇒ Vehicle diagnostic tester.

1.2 Supplementary instructions and assem‐

bly work on vehicles with an air condi‐
tioning system

WARNING

Do not open the refrigerant circuit of the air conditioning sys‐

tem.

Note

To prevent damage to condenser or to refrigerant lines/hoses,

ensure that the lines and hoses are not stretched, kinked or bent.

Steps which should be taken in order to remove and install the

engine without opening the refrigerant circuit:
– Unscrew the holding clamp(s) on the refrigerent lines.
– Remove V-ribbed belt ⇒ page 36 .
– Remove AC compressor from the bracket for auxiliary units
⇒ page 35 .
– Mount the air conditioning compressor and the condenser in
such a way that the refrigerent lines/hoses are not under ten‐
sion.

1. Self diagnosis, safety measures, cleanliness regulations and directions 3

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.3 Safety precautions when working on

fuel supply system

WARNING

♦ The fuel or the fuel lines in the fuel system can become
very hot (risk of burning)!
♦ The fuel system is under pressure!
♦ Wear safety goggles and safety clothing, in order to avoid
injuries and skin contact with fuel.
♦ Place cleaning cloths around the connection point before
detaching cable connections. Reduce pressure by care‐
fully removing the wiring.
For reasons of safety, the power supply to the fuel pump must
be interrupted before the fuel system is opened. The fuel pump
would otherwise be activated when the driver's door is opened.
One of the following options must be used to interrupt the cur‐
rent supply:
♦ Disconnect battery
or
♦ Take out fuse for fuel pump control unit - J538-
or
♦ Disconnect the plug on the flange of the fuel delivery unit

WARNING

When undertaking all installation work, particularly in the en‐

gine compartment because of its cramped construction, please
observe the following:
♦ Lay lines of all kinds (e.g. for fuel, hydraulic fluid, cooling
fluid and refrigerant, brake fluid, vacuum) and electrical
lines in such a way that the original line guide is re-estab‐
lished.
♦ Ensure that there is adequate free access to all moving or
hot components.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Caution

♦ Do not remove fuel hoses from the fuel filter.

♦ Pay attention to the notes ⇒ page 200 .
♦ Do not lever the connection fittings.
♦ This leads to leaks and damage to the fuel filter top part.
♦ Ensure that no diesel fuel gets onto other components in
the engine compartment. If this happens, clean affected
components immediately!

4 Rep. gr.01 - Self-diagnosis

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Caution

♦ Because of insufficient lubrication by diesel fuel, misfuel‐

ling can cause irreversible damage to high pressure com‐
ponents, particularly the high pressure pump. Damage in
the form of engine seizure and clogging by particles can
be expected. These particles create a risk of further dam‐
age in the pressure control valve and injectors.

Caution

In order to avoid the high pressure pump to run dry and to ach‐
ieve a quick engine start after parts are replaced, the following
points must be observed.
♦ If parts of the fuel system have been removed or replaced,
to bleed the fuel system it is necessary to perform the fuel
system filling/bleeding process ⇒ page 293 .
♦ If the fuel pump, fuel line or fuel filter have been removed
or replaced, the fuel system filling/bleeding process must
be performed ⇒ page 293 .
♦ If the high pressure pump is removed or replaced, the in‐
itial fuel filling of the high pressure pump must be carried
out before the first engine start ⇒ page 293 .
♦ If the high pressure system was opened, it must be
checked for tightness ⇒ page 293 .

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Whenunless
removing
authorisedand installing
by ŠKODA AUTO A.the fuel gauge
S. ŠKODA AUTO A. S.sender or the fuel
does not guarantee or accept any liability
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
deliverywith
unit from a full or partly filled fuel tank, pay attention to
the following points:
♦ The extraction hose of an exhaust extraction system which is
switched on, must be positioned close to the assembly open‐
ing of the fuel tank in order to extract the released fuel vapours,
even before the work is commenced. If no exhaust extraction
system is available, a radial fan (motor not in air flow of fan)
with a delivery volume of more than 15 m3/h must be used.
♦ Prevent skin contact with fuel! Wear fuel-resistant gloves!
Note the following if testers and measuring instruments have to
be used during a road test:
♦ Always secure the test and measuring devices on the rear seat
and have a second person operate them there.
If the test and measuring devices are operated from the passen‐
ger seat, the passenger can be injured by the release of the
passenger airbag in the event of an accident.

WARNING

Secure the diagnostic device to the rear seat and operate from
that position.

1. Self diagnosis, safety measures, cleanliness regulations and directions 5

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Observe the following points to prevent injury to persons and/or

damage to the injection and preheating system:
♦ People, who have a heart pacemaker implant, should not bend
over the engine compartment when the engine is running, as
the injection units generate an output high voltage pulse.
♦ No fuel lines must be opened when the engine is running.
♦ Disconnect and connect wires of the preheating and injection
system as well as measuring device wires when the ignition is
switched off.
♦ Do not carry out engine wash unless the ignition is switched
off.
♦ If the engine must be operated at starter speed, without it
starting, unplug the connector -2- at the fuel pressure regulat‐
ing valve - N276- -Pos. 1-.
♦ Before disconnecting the battery determine the code of the
radio fitted with anti-theft coding.
♦ Always switch off the ignition before disconnecting and re-
connecting the battery. Otherwise the engine control unit may
be damaged.
♦ After connecting the battery, carry out certain additional oper‐
ations ⇒ Electrical System; Rep. gr. 27 .

1.4 Safety measures for working on vehi‐

cles with start/stop system
When working on vehicles with start/stop system, please observe
the following instructions:

WARNING

Risk of injury from automatic engine start on vehicles with start/

stop system.
♦ In vehicles with an activated start-stop system (indicated
by a message in the dash panel insert), the engine can
start automatically if necessary.
♦ You must therefore ensure that the start/stop system is
deactivated (switch off the ignition, switch the ignition on
again if necessary) when working on the vehicle.

1.5 Regulations concerning cleanliness

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
when working on the fuel supply/fuel in‐
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

jection system
When working on the fuel supply and injection system, pay careful
attention to the following “6 rules” for cleanliness:
♦ Thoroughly clean the connection points and their surroundings
before releasing.
♦ Place removed parts on a clean surface and cover. Use only
lint-free cloths.
♦ Carefully cover or close opened components if the repair is not
completed immediately.
♦ Only install clean components: Remove spare parts from their
wrapping immediately before fitting. Do not use any parts
which have been stored unwrapped (e.g. on a shelf or in a tool
box).

6 Rep. gr.01 - Self-diagnosis

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

♦ When the system is open: Avoid using compressed air when‐

ever possible. Avoid moving the vehicle.
♦ Also make sure no diesel fuel runs onto the coolant hoses. If
this is the case clean the hoses immediately. Contaminated
hoses must be replaced.

1.6 Regulations concerning cleanliness

when working on the exhaust gas turbo‐
charger
Carefully observe the following “5 rules” for cleanliness when
working on the exhaust gas turbocharger:
♦ Thoroughly clean the connection points and their surroundings
before releasing.
♦ Place removed parts on a clean surface and cover. Use only
lint-free cloths.
♦ Carefully cover or close opened components if the repair is not
completed immediately.
♦ Only install clean components: Remove spare parts from their
wrapping immediately before fitting. Do not use any parts
which have been stored unwrapped (e.g. on a shelf or in a tool
box).
♦ When the system is open: Avoid using compressed air when‐
ever possible. Avoid moving the vehicle.

1.7 General instructions for charge air sys‐

tem
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
WARNING unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

When undertaking all installation work, particularly in the en‐

1. Self diagnosis, safety measures, cleanliness regulations and directions 7

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Caution

In case a mechanical damage to the exhaust gas turbocharger

is found, e.g. damage to the compressor wheel, it is not suffi‐
cient to only replace the turbocharger. In order to avoid con‐
sequential damage, perform the following tasks:
♦ Clean all oil lines.
♦ Change engine oil and oil filter.
♦ Check air filter housing, air filter element and charge air
pipes as well as charge air hoses for soiling.
♦ Check all the air guides and the charge air cooler for for‐
eign bodies.
If foreign bodies are detected in the charge air system, the
complete charge-air routing must be cleaned and if necessary
the charge air cooler must also be replaced.

♦ The charge-air system must be tight, check ⇒ page 284 .

♦ Replace the gaskets, the sealing rings and the self-locking
nuts.
♦ Hose connections and hoses of the charge air system must
be free of oil and grease before being installed. The gasket
ring and the sealing surface must be slightly oiled only for
push-fit couplings ⇒ page 281 .
♦ Observe assembly markings on the hoses and components.
♦ All hose connections of the charge air system are secured with
spring strap clamps or push-fit couplings.
♦ Only install approved clamps for securing the hose connec‐
tions ⇒ ETKA - Electronic Catalogue of Original Parts .
♦ Hose clip pliers are recommended to install spring-type clips.
♦ Install hose connections with screw clamps ⇒ page 281 .
♦ Before screwing down the oil feed line, fill the exhaust turbo‐
charger via the connection fitting with engine oil.
♦ After installing the turbocharger, run engine at idling speed for
about 1 minute to ensure that oil is supplied to the turbocharg‐
er.

8 Rep. gr.01 - Self-diagnosis

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 – Removing and installing engine

1 Removing and installing engine

1.1 Removing and installing engine trim

panel

Caution

When removing and installing the engine trim panel, where

applicable, prevent a collision with the fuel return-flow line or
prevent coming into contact with the lines by accident. In un‐
favourable situations, the outlets on the injectors may break
off. This can cause leaks in the fuel system.
The brackets of the engine cover on the cylinder head cover
can break off when they are incorrectly removed.
♦ It is therefore necessary to remove the engine cover ac‐
cording to the following instruction.

– Carefully pull the engine cover off the retaining bolts one after
another -arrows-. Do not pull engine cover off in jerks or on
one side.
Install
– To avoid damage, do not strike the engine cover with the fist
or a tool.
– Position the engine cover paying attention
Protected to the
by copyright. oil for
Copying fillprivate
sup‐or commercial purposes, in part or in whole, is not permitted
ports and dipstick. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– First press the engine cover into the rubber grommets on the
left side, then into the rubber grommets on the right side.

1.2 Removing engine

Special tools and workshop equipment required
♦ Removal tool for inner lining of the door panel - MP8-602/1-
♦ Engine and gearbox jack - V.A.G 1383 A-
♦ Double ladder
♦ Screw plug set for engine - VAS 6122-
♦ Catch pan , e.g. -VAS 6208-
♦ Hose clip pliers - VAS 6362-

♦ Locking pin - T10060 A-

♦ Engine mount - T10497- with bolts -T10497/1-
♦ Protective goggles
♦ Protective gloves

1. Removing and installing engine 9

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Procedure

Note

♦ If the stripped engine is replaced after engine removal, the

tightening of the injection unit clamping claws on the new strip‐
ped engine must be checked. Specified torque: -Pos. 8-
⇒ page 295 .
♦ The engine is removed downwards together with the gearbox.
♦ Fit all cable straps on again in the same place when installing.
♦ Fit all heat protection sleeves on again in the same place when
installing.

WARNING

Danger of scalding due to hot steam and hot coolant.

♦ When the engine is warm, the cooling system is under
overpressure.
♦ Reduce excess pressure by covering the cap of the cool‐
ant expansion tank with a cloth and opening it carefully.

– Remove assembly bracket -9- without steering gear ⇒ Chas‐

sis; Rep. gr. 40 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove the front left and right wheelhouse liner ⇒ Body Work;
Rep. gr. 66 .
– Drain coolant ⇒ page 139 .
– Remove engine cover ⇒ page 9 .

10 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -1, 3-.

– Unlock catch -arrows-, remove cover-2-.

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove top part-1- of air guide.

– Disconnect the plug connection -2- at the air mass meter -

G70- .
– Disconnect vacuum hose -4-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Loosen hose clamp -3-, remove air guide hose.
– Remove radiator air filter housing -1-.

– Release screw left and right -arrow-.

– Unclip and remove bottom part -1- of air guide.

1. Removing and installing engine 11

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove battery tray -1- ⇒ Electrical System; Rep. gr. 27 .

– Press release buttons on the hose -1- for crankcase ventila‐

tion, remove hose from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

Note

-Do not pay attention to the position 3-.

– Remove the vacuum hose -2- from the vacuum unit for charge
pressure control.
– Disconnect the vacuum hose -1- at the T-piece.

– Unlock catch -arrow-, remove vacuum hose -1-.

Note

-Do not pay attention to positions 2, 3-.

Note

Place a cloth under heating heat exchanger to absorb escaping

coolant.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– If installed: Remove heat with
protection sleeve.
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

12 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Raise holding clamps -arrows-, remove coolant hoses from

heat exchanger for heating.

– Expose the following plug connections and electric cables:

1- for exhaust gas temperature sender 4 - G648-
2- for exhaust gas temperature sender 3 - G495-
– Take electrical plug connection-3- for lambda probe - G39- out
of the holder, disconnect and expose electric cable.
Vehicles fitted with auxiliary heating

– Remove heat protection sleeve -2-.

– Loosen hose clamp -1-, remove coolant hose.
Continued for all vehicles

– Disconnect the plug connection -5- at the differential pressure

sender - G81- .

WARNING

Risk of scalding by very hot fuel.

♦ The temperature of the fuel lines and fuel can be up to 100
°C after switching off the engine in extreme cases. Let the
fuel cool down before opening the fuel line connections,
as otherwise there is a high risk of scalding.
♦ Wear protective gloves.
♦ Wear safety goggles.

– Loosen hose clamps -4, 6-, remove fuel supply hose and re‐
turn hose.
– Loosen hose clamps -1, 3-, remove coolant hoses.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Release screw -2-. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1. Removing and installing engine 13

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Pull out the fuel feed line -2- and catch the fuel which flows out
with a cleaning cloth. Unlock the quick coupling and discon‐
nect ⇒ page 226 .
Vehicles with radiator versions 1 and 2

– Raise holding clamp -arrow-, remove coolant hose right above

radiator for charge air circuit.
Continued for all vehicles

– Raise holding clamp -arrow-, remove top left coolant hose

from radiator.

Note

For the following clip unclipping procedure use the removal tool
for inner door trim panel - MP8-602/1- .

– Remove plug -2- from engine control unit - J623-

⇒ page 336 .
– Take electrical plug connections -1, 3, 4- out of the holder and
disconnect.
– Expose electric cables.

14 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock catches -arrows-, remove cover-1- for engine com‐

partment E-box.

– Unlock catch with a screwdriver -arrow-, pull cover -1- for E-

box engine compartment upwards.

– Unscrew nut -arrow-, remove and expose electric cable.

Vehicles fitted with a manual gearbox

– Separate electrical plug connection -2-.

– Press back B+-pole protection -1- and unscrew B+-cable from
the starter magnet switch.
– Release nuts -3-, remove earth cable.

– Disconnect front left electrical plug connections at the gear‐

box:
1- Gearbox neutral position sender - G701-
2- Reversing light switch - F4-
– Remove switching and selector linkage from gearbox, un‐
screw linkage support and lay aside with the linkages ⇒
Gearbox; Rep. gr. 34 .
Vehicles fitted with manual gearbox 0A4
– Remove clutch sender cylinder and lay to the side with con‐
nected pipe/hose line ⇒ Gearbox; Rep. gr. 30 .

– Screw out screws -arrows- for gearbox mount by approxi‐

mately 2 turns.
Vehicles fitted with manual gearbox 02Q
– Remove pressure line from breather/slave cylinder ⇒ Gear‐
box; Rep. gr. 30 .

– Screw out screws -arrows- for gearbox mount by approxi‐

mately 2 turns.
Vehicles with dual clutch gearbox 0CW

16 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate plug connection -3-.

– Press back B+-pole protection -2- and unscrew B+-cable from
the starter magnet switch.
– Release nuts -4-, remove earth cable.

Caution

Risk of destruction of the (mechatronics) control unit by static

discharge.
♦ Do not allow the gearbox plug contacts to come into con‐
tact with your hands.

– To discharge any static electric charge built up on your body,

touch the earth with your hand (without gloves).
– Disconnect electric plug connection -1- for dual clutch gearbox
mechatronics - J743- , turn the turn lock anticlockwise.
– Remove selector lever linkage from gearbox, unscrew linkage
support and strap up with selector lever linkage ⇒ Gearbox;
Rep. gr. 34 .

– Screw out screws -arrows- for gearbox mount by approxi‐

mately 2 turns.
Vehicles with dual clutch gearbox 0D9
– Remove selector lever linkage from gearbox and pull it out of
the linkage support ⇒ Gearbox; Rep. gr. 34 .

– Separate plug connection -2-.

– Press back B+-pole protection -1- and unscrew B+-cable from
the starter magnet switch.
– Unscrew the earth cable on the body.

Caution

Risk of destruction of the (mechatronics) control unit by static

discharge.
♦ Do not allow the gearbox plug contacts to come into con‐
tact with your hands.

– To discharge any static electric charge built up on your body,

touch the earth with your hand (without gloves).
– Disconnect electric plug connection -4- for dual clutch gearbox
mechatronics - J743- , turn the turn lock anticlockwise.

1. Removing and installing engine 17

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Screw out gearbox mount screws -2- by approximately 2 turns.

Note

-Do not pay attention to the position 1, A-.

Continued for all vehicles

– Screw out screws -arrows- for engine mount by approximately

2 turns.
Vehicles fitted with auxiliary heating

– Loosen clamp -1-, unscrew nut -2-, remove silencer for auxil‐
iary heating.
Continued for all vehicles
– Remove the ribbed V-belt ⇒ page 36 .

18 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electric plug connection -1- on the control valve for

the air conditioning system - N280- compressor.

Caution

Risk of damaging AC compressor, refrigerant lines and hoses.

♦ Do not over-tension, buckle or bend refrigerant lines and
hoses.

– Unscrew screws -arrows-.

WARNING

Risk of injury through refrigerant.

♦ Do not open the refrigerant circuit of the air conditioning
system.

– Remove AC compressor with connected refrigerant hoses

from the holder and strap up to the right side.

– Unscrew left and right cardan shaft -arrow- from the gearbox
⇒ Chassis; Rep. gr. 40 and strap up towards the rear.

Note

Make sure that the surface protection of the cardan shaft is not
damaged.

1. Removing and installing engine 19

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect the plug connection -1- at the exhaust flap control

unit - J883- .
– Slacken the clamping sleeve -2- and slide it backwards.

– Loosen screw -2- and remove clamping sleeve.

– Remove pre-exhaust pipe.

Note

-Do not pay attention to the position 1-.

For vehicles with engine identification characters CRKB

– Undo the left underfloor trim panel in the middle in the direction
of the exhaust pipe and press down ⇒ Body Work; Rep. gr.
50 .

– Take the electrical plug connection -arrow- for Lambda probe

after catalytic converter - G130- out of its holder and discon‐
nect, expose the electric cable.
Continued for all vehicles

– Separate electrical plug connection -4-.

– Release nut -2- and screws -3-.
– Press coolant pipe -1- and pump for charge air cooler - V188-
-Pos. 5- to the side.

Note

Different designs according to build version.

20 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen clips -arrows-, remove noise insulation -1- for oil sump.
Vehicles with four-wheel drive

– To reinstall, mark the position of the flexible disk and the angle
gearbox flange to each other.

– Unscrew the propshaft from the angle gearbox -arrows-, while

counterholding with a lever on the triangular flange.

– Push engine/gearbox assembly slightly forward (towards the

front of the body) and then pull off the propshaft from the angle
gearbox.

WARNING

Risk of damage to the gasket ring -arrow- in the flange of the

propshaft.
Push propshaft horizontally as far back and towards the right
vehicle side as possible.

Note

In case of damaged gasket ring the propshaft must be replaced.

Continued for all vehicles

1. Removing and installing engine 21

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Tighten engine mount - T10497- with bolt -T10497/1- with

screw -1- to around 20 Nm at cylinder block. Use the upper
elongated hole “A” to do so.
– Insert engine and gearbox jack - V.A.G 1383 A- at engine
mount - T10497- and slightly raise the engine/gearbox unit.

Note

Use double ladder to release the screws for the assembly bracket.

– Screw out engine mount screws -arrows- fully.

– Screw out gearbox mount screws -arrows- fully.

Note

♦ 2 or 3 screws according to gearbox.

♦ The gearbox mount for a vehicle with dual clutch gearbox 0CW
is shown as an example.

Caution
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Risk of damaging vacuum lines or electric cables and the en‐
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
gine compartment.
♦ Check that all vacuum lines and electric cables between
engine, gearbox and body have been loosened.
♦ Guide the engine/gearbox unit out of the engine compart‐
ment carefully when lowering.

– Drain engine/gearbox unit.

1.3 Securing the engine to the assembly

stand
Special tools and workshop equipment required
♦ Engine and gearbox support - VW 540-

22 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

♦ Lifting device - MP 9-201 (2024A)-

♦ Engine bracket - MP 1-202-
♦ Assembly stand - MP 9-101-
♦ Workshop crane , e.g. -VAS 6100-
Precondition
• Separate engine from gearbox.

WARNING

Use securing pins on the hooks and rig pins to prevent release.

– Attach lifting device - MP 9-201 (2024A)- to engine and work‐

shop crane , e. g. -VAS 6100- as shown.
On the belt pulley side:
♦ 2nd Hole of the attachment in Position 1
On the flywheel side:
♦ 4th Hole of the attachment in Position 8

Note

The illustration shows a pump injector engine. The attachment for

the Common Rail engine occurs in the same way.

– Lift engine down from engine mount -T10497- using workshop

crane - VAS 6100- .

– Secure engine with the engine and gearbox mount - VW 540-

at the engine and gearbox mount - MP 1-202- .

1. Removing and installing engine 23

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.4 Installing engine

Procedure

Note

♦ Observe all safety measures and notes for assembly work on

the fuel supply and injection system, at the charge air system
and observe as well the rules for cleanliness ⇒ page 3 .
♦ Replace screws which have been tightened firmly to a torquing
angle.
♦ Replace self-locking nuts and screws as well as gasket rings,
gaskets and O-rings.
♦ Hose connections and air guide pipes and hoses must be free
of oil and grease before being installed.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .
♦ Fit all cable straps on again in the same place when installing.

Caution

When undertaking all installation work, particularly in the en‐

– Installing intermediate plate ⇒ page 62 .

24 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– If there are no dowel sleeves -A- are available in the cylinder

block for centering the engine and gearbox, insert dowel
sleeves.

Note

A vehicle with manual gearbox is shown as an example.

Vehicles fitted with a manual gearbox

– If a needle bearing is installed in the crankshaft, remove the
needle bearing ⇒ page 72 .
– If the clutch release bearing is worn, remove the clutch release
bearing ⇒ Gearbox; Rep. gr. 30 .
– Lightly grease the gearing of the gearbox drive shaft using lu‐
bricating grease for clutch disc spline ⇒ ETKA - Electronic
Catalogue of Original Parts .
– Check the centering of the clutch disc.
Vehicles with dual clutch gearbox
– If no needle bearing is installed in the crankshaft, install needle
bearing ⇒ page 72 . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Continued for all vehicles with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Secure gearbox to engine.

– Install gearbox support bracket.
– Take up engine/gearbox unit with the engine mount -T10497- .
– Insert engine/gearbox unit into the body.

– Initially insert screws -arrows- for engine mount by hand as far

as the stop.

1. Removing and installing engine 25

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Initially insert screws -arrows- for gearbox mount by hand as

far as the stop.

Note

♦ The gearbox mount for a vehicle with dual clutch gearbox 0CW
is shown as an example.
♦ The screws must not be permanently tightened until the as‐
sembly bracket is adjusted ⇒ page 33 .

– Remove engine mount -T10497- from engine.

– Install the starter motor ⇒ Electrical System; Rep. gr. 27 .
– Install pump for charge air cooler - V188- ⇒ page 153 .
– Install air guide pipe ⇒ page 282 .
Vehicles with dual clutch gearbox
– Install and adjust the selector lever linkage ⇒ Gearbox; Rep.
gr. 34 .
Continued for all vehicles
– Install inlet connection ⇒ page 265 .
– Install pre-exhaust pipe ⇒ page 349 .
– Install drive shafts ⇒ Chassis; Rep. gr. 40 .
– Install AC compressor ⇒ Heating, Air Conditioning; Rep. gr.
87 .
– Install poly V-belt ⇒ page 36 .
– Install engine control unit ⇒ page 336 .
– Install differential pressure indicator - G505- ⇒ page 319 .
– Connect clutch sender cylinder ⇒ Gearbox; Rep. gr. 30 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Bleed clutch hydraulics ⇒ authorised
unless Gearbox; Rep.AUTO
by ŠKODA gr. A.30 .
S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Install linkages with linkage support ⇒ Gearbox; Rep. gr. 34 .
– Adjusting the assembly bracket ⇒ page 33 .
– Remove battery tray ⇒ Electrical System; Rep. gr. 27 .
– Electrical connections and proper routing ⇒ Electrical System;
Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
– Connect vacuum hoses ⇒ page 279 .
– Install air filter ⇒ page 332 .
– Checking the oil level ⇒ Maintenance ; Booklet Octavia III .

Caution

Risk of damaging control units as a result of overvoltage.

♦ Do not use charger for jump starting!

– Venting air from the fuel system ⇒ page 293 .

– Connect coolant hoses with quick coupling ⇒ page 172 .
– Replenish coolant ⇒ page 140 .

26 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

Do not re-used used coolant.

– Install the assembly carrier ⇒ Chassis; Rep. gr. 40 .

– Install front wheelhouse liners ⇒ Body Work; Rep. gr. 66 .
Tightening torques

Note

♦ Tightening torques apply only for lightly greased, oiled,

phosphatized or blackened nuts and screws.
♦ Other lubricants such as engine and gearbox oil are allowed,
but no lubricants containing graphite.
♦ Do not use degreased parts.
♦ The tightening torque tolerance varies by ± 15 %.

Component Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Screws and nuts M6
unless authorised by ŠKODA10 AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
M7 15
M8 20
M10 40
M12 65
♦ Assembly overview - assembly mountings
⇒ “2.1 Assembly overview - assembly mountings”, page 28
♦ Attachment of engine/gearbox ⇒ Gearbox; Rep. gr. 34 .

1. Removing and installing engine 27

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Assembly bracket

2.1 Assembly overview - assembly mountings

1 - Bolt
❑ replace after removal
❑ order of tightening
⇒ page 29
2 - Engine support bracket
❑ removing and installing
⇒ page 31
3 - Engine mounting
❑ with supporting arm
❑ removing and installing
⇒ page 30
4 - 40 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
5 - 20 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
6 - 40 Nm + torque a further 90°
(1/4 turn)
❑ replace
Protectedafter removal
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
7 - 60 Nm +with
torque
respect a
to further 90° of information in this document. Copyright by ŠKODA AUTO A. S.�
the correctness
(1/4 turn)
❑ replace after removal
8 - Pendulum support
❑ different designs; as‐
signment ⇒ ETKA -
Electronic Catalogue of
Original Parts
❑ removing and installing
⇒ page 32
9 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 29
10 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 29
11 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 29
12 - 60 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
13 - 60 Nm + torque a further 90° (1/4 turn)
❑ replace after removal

28 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

14 - Gearbox mount
❑ with supporting arm
15 - 50 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
16 - Bolt
❑ Tightening torque ⇒ Gearbox; Rep. gr. 34
17 - Gearbox support bracket
❑ for vehicles with manual gearbox
18 - Bolt
❑ Tightening torque ⇒ Gearbox; Rep. gr. 34

Engine support bracket - tightening torque and tightening order

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Tighten screws in steps in the given sequence:

Stage Screws Tightening torque/torquing angle
1. -1 … 3- 7 Nm
2. -1 … 3- 40 Nm
3. -1 … 3- Turn 180° further

Install pendulum support

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Tighten screws in steps in the given sequence:

Stage Screws Tightening torque/torquing angle
1. -2, 3- 50 Nm
2. -1- 130 Nm
3. -1 … 3- Turn 90° further

2.2 Support the engine in its installed posi‐

tion
Special tools and workshop equipment required
♦ Supporting device - T30099-
♦ Pressure screw - T30119-
♦ Supporting device - T40091/1-
♦ -T40091/3- from engine support basic set - T40091-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Support - 10-222 A/31- unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Supporting device - MP9-200/10-

2. Assembly bracket 29
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

♦ Adapter - MP9-200/18 (10-222A/18)-

Procedure
– Remove windscreen wiper arms -arrows- ⇒ Electrical System;
Rep. gr. 92 .
– Remove plenum chamber cover -5- Body Work⇒ Body Work;
Rep. gr. 50 .
– Remove engine cover ⇒ page 9 .
– Remove caps of the screw connections of the front suspension
strut dome.
– Position the supporting device - T30099- with -T40091/3- with
the adapters as shown.
– Support engine on right eye and slightly release load from as‐
sembly mounting by turning spindle.
Assembling
Install in the reverse order of removal. When doing this, note the
following:
– Install the plenum chamber cover ⇒ Body Work; Rep. gr. 50 .
– Install windscreen wiper arms ⇒ Electrical System; Rep. gr.
92 . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2.3 Removing and installing engine mount

Removing
– Remove engine cover ⇒ page 9 .
– Press release buttons on the hose -1- for crankcase ventila‐
tion, remove hose from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Slacken hose clamp -3-, remove air guide pipe from air mass
meter - G70- .
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

– Separate electrical plug connection -1-.

– Remove bracket -2- with fuel hoses.
– Unlock catches using a screwdriver -arrow-, lay coolant ex‐
pansion tank to the side.

30 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Expose bracket -3- with fuel hoses.

– Release nut -2- and screws -1-.
– Lay fuel filter -4- to the side.
– Support the engine in its installed position ⇒ page 29 .

– Release screws -arrows- and remove heat shield -1-.

Install
Install in the reverse order of removal. When doing this, note the
following:
– Check assembly bracket setting ⇒ page 33 .
Tightening torques
♦ Assembly overview - assembly mounting
⇒ “2.1 Assembly overview - assembly mountings”, page 28
♦ Exhaust gas turbocharger with component parts - Summary
of components
⇒ “1.1 Exhaust gas turbocharger with component parts - Sum‐
mary of components”, page 265
♦ Summary of components - fuel filter ⇒ page 196

2.4 Removing and installing engine support

Removing
– Remove engine mounts ⇒ page 30 .
– Remove top toothed belt guard ⇒ page 43 .
– Use the spindle - MP9-200/10- for raising and lowering until
all screws are accessible.

Note

Remove the screw -2- together with the engine support.

– Release screws -1, 2 and 3- and remove engine support.

Install Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Installation is carried out in the reverse
with respectorder. Whenofinstalling,
to the correctness information in this document. Copyright by ŠKODA AUTO A. S.�
note the following:
– Install the fixing screw -2- together with the engine support.

2. Assembly bracket 31
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Tighten the fixing screws in the sequence -1 - 2 - 3- by hand

initially.
– Tighten all bolts fully in the specified sequence
⇒ Fig. ““Engine support bracket - tightening torque and tight‐
ening order”“ , page 29 .
– Install top toothed belt guard ⇒ page 43 .
– Install engine mount ⇒ page 30 .

2.5 Removing and installing pendulum sup‐

port
Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .
– Release screws -1, 2, 3- and remove pendulum support.

Note

A vehicle with manual gearbox 02Q is shown as an example.

Install
Installation is carried out in the reverse order.
Tightening torques
♦ Install pendulum support
⇒ Fig. ““Install pendulum support”“ , page 29 .
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

32 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.6 Checking and adjusting the assembly

bracket

2.6.1 Checking the assembly bracket

Procedure
The following dimensions must be reached:
• A distance of -a- = 10 mm must be present between engine
support -2- and engine mount -1-.
• The cast edge on the engine support must be parallel with the
engine mount supporting arm.
• Dimension -b- = dimension -b-.

Note

The distance -a- = 10 mm can be checked, for example with suit‐

able round bars.

– If the measured distance is too great or too small, adjust the

assembly bracket ⇒ page 33 .

2.6.2 Adjusting the assembly bracket

Procedure
– Support the engine in its installed position ⇒ page 29 .
– Slightly pre-tension engine/gearbox unit with the spindle -
MP9-200/10- , do not raise.

– Unscrew screws -arrows- for engine mount one after another

and replace (if not already done during engine installation).
– Initially, loosely insert the screws.
– Move engine/gearbox unit with an assembly lever until the fol‐
lowing dimensions are set:

2. Assembly bracket 33
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

• A distance of -a- = 10 mm must be present between engine

support -2- and engine mount -1-.
• The cast edge on the engine support must be parallel with the
engine mount supporting arm.
• Dimension -b- = dimension -b-.

Note

The distance -a- = 10 mm can be checked, for example with suit‐

able round bars.

– Tighten engine mount screws.

Note

A gearbox mount with 2 screwed connections is shown as an ex‐

ample.

– Unscrew nut -arrow-, expose earth cable.

– Unscrew screws -arrows- for gearbox mount -1- after another

and replace (if not already done during engine installation).
– Initially, loosely insert the screws.

– Make sure that on the gearbox side the edges of the support‐
ing arm -1- and gearbox mount -2- are parallel.
• Dimension -x- = dimension -x-.
Installation is carried out in the reverse order.
Tightening torques
♦ Assembly overview - assembly mounting
⇒ “2.1 Assembly overview - assembly mountings”, page 28

34 Rep. gr.10 - Removing and installing engine

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

13 – Crankshaft group
1 Removing and installing a V-ribbed
belt and a toothed belt

1.1 V-ribbed belt - Summary of components

1 - Poly V-belt
❑ check for wear
❑ mark the direction of ro‐
tation with chalk or a felt-
tip pen before removing
❑ do not kink
❑ Routing of the ribbed V-
belt ⇒ page 37
❑ removing and installing
⇒ page 36 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ pay attention to the cor‐ with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

rect position on the belt

pulley when installing it.
2 - 10 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
❑ Use only original screws
⇒ ETKA - Electronic
Catalogue of Original
Parts
3 - Crankshaft-belt pulley
❑ with vibration damper
❑ Fitting position: Bore in
the vibration damper
must be positioned
above the elevation on
the crankshaft toothed
belt pulley
❑ removing and installing
⇒ page 38
4 - Tensioning device for V-rib‐
bed belt
❑ removing and installing
⇒ page 38
5 - 20 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
6 - Screw
❑ Tightening torque -Pos. 2- ⇒ page 309
7 - Screw
❑ Tightening torque -Pos. 12- ⇒ Item 12 (page 42)
8 - Damper wheel
9 - Fitting sleeve
❑ pay attention to correct fit in the bracket for auxiliary units

1. Removing and installing a V-ribbed belt and a toothed belt 35

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 - Bracket for auxiliary units

❑ removing and installing ⇒ page 39
11 - High pressure pump
❑ Summary of components ⇒ page 309
12 - Generator
❑ Summary of components ⇒ Electrical System; Rep. gr. 27
13 - Screw
❑ Tightening torque ⇒ Electrical System; Rep. gr. 27
14 - Screw
❑ different lengths ⇒ page 36
❑ Tightening torque and tightening order ⇒ page 36
15 - Fitting sleeve
❑ pay attention to correct fit in the AC compressor
16 - Air conditioner compressor
❑ Summary of components ⇒ Heating, Air Conditioning; Rep. gr. 87
17 - Screw
❑ Tightening torque ⇒ Heating, Air Conditioning; Rep. gr. 87

Bracket for auxiliary units - tightening torques and tightening order

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Set screws as follows:

♦ Screws -1, 2, 3, 6- M10x35.
♦ Screws -4- M10x115.
♦ Screws -5- M10x175.
– Tighten screws in steps in the given sequence:
Stage Screws Tightening torque/torquing angle
1. -1 … 6- by hand as far as the stop
2. -1 … 6- 40 Nm
3. -3- and -6- Turn 45° further
4. -1, 2, 4, 5- Turn 180° further

1.2 Removing and installing poly V-belt

Special tools and workshop equipment required
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Locking pin - T10060 A- with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

36 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .

Caution

When installing, risk of damage through reversing the rotation

direction of an already used V-ribbed belt.
♦ If the V-ribbed belt is re-installed, mark the direction of ro‐
tation with chalk or a felt-tip pen before removing it.

– To release the tension of the V-ribbed belt, use the ring span‐
ner to swivel the tensioning device anticlockwise -arrow-.
– Lock tensioning device with locking pin - T10060 A- .
– Remove poly V-belt.
Install
Installation is carried out in the reverse order. When installing,
note the following:

– Lay the V-ribbed belt onto the V-ribbed belt pulleys:

1- Crankshaft-belt pulley
2- Tensioning roller
3- Generator
4- Air conditioner compressor

– Hold the tensioning element with the ring spanner and pull out
the locking pin - T10060 A- .
– Release pressure on tensioning device.
– Check correct positioning of the V-ribbed belt.
– Start engine and check ribbed V-belt run.
Tightening torques
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

1. Removing and installing a V-ribbed belt and a toothed belt 37

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.3 Removing and installing crankshaft-belt

pulley
Removing
– Remove V-ribbed belt ⇒ page 36 .
– Loosen screws of the crankshaft-belt pulley. To do so, press
on the crankshaft-belt pulley screw with the ring spanner.
– Release screws and remove crankshaft-belt pulley.

Install
Installation is carried out in the reverse order. When installing,
note the following:

Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Replace screws which have been tightened firmly to a torquing
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

angle.

• Fitting position: The hole -arrow- in the crankshaft belt pulley

must be positioned above the elevation on the crankshaft tim‐
ing belt sprocket.
– Install poly V-belt ⇒ page 36 .
Tightening torques
♦ Assembly overview - cylinder block (pulley end)
⇒ “1.1 V-ribbed belt - Summary of components”, page 35

1.4 Removing and installing tensioning de‐

vice for V-ribbed belt
Removing
– Remove V-ribbed belt ⇒ page 36 .
– Release screws -arrows- and remove tensioning device for V-
ribbed belt.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Install poly V-belt ⇒ page 36 .

Tightening torques
♦ Assembly overview - cylinder block (pulley end)
⇒ “1.1 V-ribbed belt - Summary of components”, page 35

38 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.5 Removing and installing bracket for aux‐

iliary units
Removing
– Remove the generator ⇒ Electrical System; Rep. gr. 27 .
– Remove the high pressure pump ⇒ page 310 .
– Release nut -2- and screw -1-, push front right coolant pipe
forwards slightly.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Unclip bracket -1- with fuel hoses.
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unscrew screws -arrows-.

Note

-Do not pay attention to positions 2, 3-.

– Release screw -arrow-, remove guide pulley.

1. Removing and installing a V-ribbed belt and a toothed belt 39

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release the screws in the order -6...1-.

– Unscrew screws, remove bracket for auxiliary units.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Check that a dowel sleeve is inserted between the bracket for

the auxiliary units and the cylinder block.
Tightening torques
♦ Bracket for auxiliary units - tightening torques and tightening
order
⇒ Fig. ““Bracket for auxiliary units - tightening torques and
tightening order”“ , page 36
♦ Assembly overview - toothed belt drive
⇒ “1.7 Assembly overview - toothed belt drive”, page 42
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - high pressure pump
⇒ “3.1 Summary of components - high pressure pump”, page
309
♦ Summary of components - generator ⇒ Electrical System;
Rep. gr. 27

1.6 Summary of components - toothed belt guard

40 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Bottom toothed belt guard

❑ removing and installing
⇒ page 45
2 - 12 Nm
❑ with collar
❑ inserted in the bottom
toothed belt guard such
that it cannot be lost
3 - 5 Nm
4 - Pipeline
❑ to differential pressure
sender - G505-
5 - Top toothed belt guard
❑ removing and installing
⇒ page 43
6 - 12 Nm
❑ Insert with safety agent
⇒ ETKA - Electronic
Catalogue of Original
Parts
7 - Rear toothed belt guard
❑ to remove, remove cool‐
ant pump ⇒ page 149

1. Removing and installing a V-ribbed belt and a toothed belt 41

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.7 Assembly overview - toothed belt drive

1 - 180 Nm + 135° further

❑ Further rotation can be
done across several
stages, e.g. 90° + 45°
❑ replace after removal
❑ Release and tighten us‐
ing counterholder -
T30004 (3415)-
❑ Do not additionally oil
threads and collar
2 - Crankshaft - toothed belt
sprocket
❑ there must not be any oil
present on the contact
surface between the
toothed belt sprocket
and the crankshaft
❑ can be installed only in
one position
3 - 20 Nm
4 - Guide pulley
5 - 20 Nm + torque a further 45°
(1/8 turn)
❑ replace after removal
6 - Tensioning roller
7 - Toothed belt
❑ mark the direction of ro‐
tation with chalk or a felt-
tip pen before removing
❑ check for wear
❑ removing ⇒ page 49
❑ install (set the timing)
⇒ page 52
8 - 100 Nm
❑ to release and tighten use counterholder - T10172- with adapters -T10172/11-
❑ Do not additionally oil threads and collar
9 - 9 Nm
10 - Camshaft toothed belt pulley
❑ There must not be any oil present on the contact surface between the toothed belt pulley and the camshaft
11 - Camshaft driver
❑ removing and installing ⇒ “2.5 Removing and installing camshaft housing”, page 104
12 - 20 Nm
13 - GuideProtected
pulleyby copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
14 - High pressure
with respectpump
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ Summary of components ⇒ page 309

15 - Hub
❑ for high pressure pump
❑ Summary of components ⇒ page 309

42 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ There must not be any oil present between the lock hub and the toothed belt pulley
16 - Toothed belt pulley high pressure pump
❑ Summary of components ⇒ page 309
❑ There must not be any oil present between the lock hub and the toothed belt pulley
17 - Nut
❑ Do not additionally oil threads and collar
❑ Tightening torque -Pos. 4- ⇒ page 309
18 - O-ring
❑ replace after removal
❑ Moisten with coolant
19 - Coolant pump
❑ removing and installing ⇒ page 149
20 - Screw
❑ Tightening torque -Pos. 11- ⇒ page 147

1.8 Removing and installing top toothed belt

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
guard unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Special tools and workshop equipment required

♦ Extension SW 17 from the set of tools - T10395-

Note

Observe rules for cleanliness ⇒ page 6 .

Removing
– Remove engine cover at the top ⇒ page 9 .
– Disconnect fuel lines -1, 2-, to do so, first press hose coupling
downwards -arrow A-, then press release buttons down
-arrow B-. Unlock the quick coupling and disconnect
⇒ page 226 .
– Remove hose coupling with pressed release buttons.

– Unclip bracket -3- with fuel hoses.

– Release nut -2- and screws -1-.
– Lay fuel filter -4- to the side.

1. Removing and installing a V-ribbed belt and a toothed belt 43

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew exhaust temperature sender 3 - G495- -B- with a tool

from the tool set SW 17 - T10395- .
– Open clamp -A-, pull off coolant hose and push to the side.
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CRVC, CUPA

– Open heat protection sleeve -1-.

– Disconnect plug connection -4-.
– Unscrew screw -3-, remove differential pressure sender -
G505- from the holder.

– Release screw -arrow-.

– Open clamp -A-, pull out hose, unclip pipeline -B- and remove
with the differential pressure sender - G505- .
For vehicles with engine identification characters CRKB

– Open heat protection sleeve -1-.

– Disconnect electrical plug connection -3- and put the electric
cable to one side.
– Release screw -2-.
– Separate electrical plug connection -4-.

44 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Detach vacuum hose -arrow- and put to one side.

– Release screw -3-.

– Loosen hose clamps -1-, remove hoses.
– Lay pipelines -2- to one side.
Continued for all vehicles

– Unlock catches -arrows-, unhook and remove top toothed belt

guard -1-.
Install
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Installation is carriedunless
out in the reverse
authorised order.
by ŠKODA AUTO When
A. S. ŠKODA installing,
AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
note the following:
– Venting air from the fuel system ⇒ page 293 .
Tightening torques:
♦ Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370
♦ Summary of components - fuel filter ⇒ page 196
♦ Control line pressure difference sensor on toothed belt guard
⇒ “1.6 Summary of components - toothed belt guard”,
page 40

1.9 Removing and installing bottom toothed

belt guard
Removing

Note

♦ To simplify the production process in manufacturing plants,

the bottom toothed belt guard is fitted with a guide, which rea‐
ches into the sealing flange. To remove the bottom toothed
belt guard although the engine support is installed, this guide
in the toothed belt guard must be destroyed.
♦ Note different versions!

– Remove crankshaft-belt pulley ⇒ page 38 .

1. Removing and installing a V-ribbed belt and a toothed belt 45

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

WARNING

Risk of engine damage if the toothed belt is damaged.

♦ Perform following work step very carefully!

– For a toothed belt guard of an expiring series, set bores to the

following dimensions:
♦ Dimension -a-: 10 mm
♦ ∅ 8 mm
– Guide the screwdriver through the hole and break off the guide
peg of the toothed belt guard towards the rear.

– For a newer toothed belt guard version, put a screwdriver into

the guide peg slot.
– By turning the screwdriver in -direction of arrow-, break off the
guide peg.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unscrew screws -arrows-.

– Unhook bottom toothed belt guard -1- upwards and remove.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

When a new toothed belt guard is being installed the guide peg
-arrow- must be disconnected before installation.

46 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Position the toothed belt guard, pay attention to fit pin

-arrow- while doing so.
Tightening torques
♦ Summary of components - toothed belt guard
⇒ “1.6 Summary of components - toothed belt guard”,
page 40

1.10 Remove the toothed belt from the cam‐

shaft
Special tools and workshop equipment required
♦ Rig pin for the diesel injection pump - 3359-
♦ Counterholder - T10051-
♦ Counterholder - T10172- with adapters -T10172/11-
♦ Offset screwdriver - T10264-
♦ Rig tool - T10265-
♦ Crankshaft arrester - T10490-
♦ Rig pin - T10492-
Removing
– Remove top toothed belt guard ⇒ page 43 .
– Remove crankshaft-belt pulley ⇒ page 38 .

WARNING

Risk of destruction as a result of the toothed belt pulley jump‐

ing.
♦ Only rotate the crankshaft in the direction of rotation of the
engine!

– Turn the crankshaft at the screw for toothed belt pulley until
the camshaft toothed belt pulley is positioned on “TDC”.
– Lock hub of the camshaft using the diesel injection pump rig
pin - 3359- ; to do so, insert the rig pin into fork -2- of the driver
and into the bore behind it -1- in the cylinder head.

1. Removing and installing a V-ribbed belt and a toothed belt 47

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen fixing screw -1- in the camshaft sprocket by half a turn

but do not release it.

Note

-Do not pay attention to the position 2-.

– Lock the crankshaft toothed belt pulley using the crankshaft

arrester - T10490- .
• The studs of the crankshaft arrester - T10490- must reach into
the threaded bores of the toothed belt pulley.
• The rig pin of the crankshaft arrester - T10490- must reach into
the bores at the sealing flange.

Caution

Risk of engine damage.

♦ The diesel injection pump rig pin - 3359- must not be used
as a counterholder for loosening the camshaft toothed belt
pulley.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Loosen screw -arrow- for camshaft toothed belt
withpulley;
respect to to
the do
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
so, use counterholder - T10172- with adapters -T10172/11- .

– Lock hub of the high pressure pump using the rig pin -
T10492- ; to do so, insert the rig pin into fork -2- of the hub and
into the bore behind it -1- in the auxiliary units bracket.

48 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen nut -arrow- for high pressure pump toothed belt pulley
by approximately 90°, use counterholder - T10051- to do so.

– Loosen nut -1- for tensioning pulley.

– Carefully turn eccentric of the tensioning pulley with offset
screwdriver - T10264- clockwise -arrow- until the tensioning
pulley can be interlocked with the rig tool - T10265- .

– Then turn the eccentric of the tensioning pulley with the offset
screwdriver - T10264- clockwise -arrow- up to the stop and
tighten nut -1- by hand.
– Remove the toothed belt from the camshaft toothed belt pul‐
ley.
Installing (set the timing) ⇒ page 52

1.11 Removing and installing toothed belt

Special tools and workshop equipment required
♦ Rig pin for the diesel injection pump - 3359-
♦ Counterholder - T10051-
♦ Counterholder - T10172- with adapters -T10172/11-
♦ Offset screwdriver - T10264-
♦ Rig tool - T10265-
♦ Crankshaft arrester - T10490- Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Rig pin - T10492- with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Removing
– Remove engine support ⇒ page 31 .
– Remove top toothed belt guard ⇒ page 43 .
– Remove bottom toothed belt guard ⇒ page 45 .

1. Removing and installing a V-ribbed belt and a toothed belt 49

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

WARNING

Risk of destruction as a result of the toothed belt pulley jump‐

ing.
♦ Only rotate the crankshaft in the direction of rotation of the
engine!

– Loosen fixing screw -1- in the camshaft sprocket by half a turn

but do not release it.

Note
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
-Do not pay attention to the position
unless authorised 2-. A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
by ŠKODA AUTO
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Lock the crankshaft toothed belt pulley using the crankshaft

WARNING

Risk of engine damage.

♦ The diesel injection pump rig pin - 3359- must not be used
as a counterholder for loosening the camshaft toothed belt
pulley.

– Remove rig pin and partially undo the screws for the camshaft
sprocket. Before removing fully, peg back the rig pin.

50 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen screw -arrow- for camshaft toothed belt pulley; to do

so, use counterholder - T10172- with adapters -T10172/11- .

– Lock hub of the high pressure pump using the rig pin -
T10492- ; to do so, insert the rig pin into fork -2- of the hub and
into the bore behind it -1- in the auxiliary units bracket.
– Unscrew the rig pin and partially unscrew the nuts for the high
pressure pump toothed belt. Before removing fully, peg back
the rig pin.

– Loosen nut -arrow- for high pressure pump toothed belt pulley
by approximately 90°, use counterholder - T10051- to do so.

– Loosen nut -1- for tensioning pulley.

– Carefully turn eccentric of the tensioning pulley with offset
screwdriver - T10264- clockwise -arrow- until the tensioning
pulley can be interlocked with the rig tool - T10265- .

1. Removing and installing a V-ribbed belt and a toothed belt 51

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Then turn the eccentric of the tensioning pulley with the offset
screwdriver - T10264- clockwise -arrow- up to the stop and
tighten nut -1- by hand.

WARNING

Risk of damage through reversing the rotation direction of an

already used toothed belt.
♦ Mark the direction of rotation with chalk or a felt-tip pen for
the re-installation before removing the toothed belt pulley.

– First remove the toothed belt from the coolant pump and then
from the remaining toothed belt gears.
Installing (set the timing)

Note

The engine must be cold for performing installation work on the

toothed belt.

WARNING

Risk of damage to valves and piston crowns.

♦ When rotating the camshaft, the crankshaft must not be
positioned at “TDC” with any one piston.

Requirements:

• Tensioning pulley locked with rig tool - T10265- and fixed with
nut -1- up to right stop.

• Sheet peg -arrow- of the tensioning pulley must engage in the

cast iron recess of the cylinder head. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

52 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

• Lock the hub of the camshaft with the rig pin for diesel injection
pump - 3359- .
• Screw loosely inserted.
• It must still be possible to just turn the camshaft toothed belt
pulley, however it must not tilt.

• Fixing screw -1- of the driver loosened by one half turn, posi‐
tioned in the centre position in the elongated hole -2-.

• Interlock crankshaft with crankshaft arrester - T10490- .

• Lock hub of high pressure pump with rig pin - T10492- .

• Nut loosely inserted.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
• It must still be possible toauthorised
unless just turn the toothed
by ŠKODA AUTO A. S. belt pulley
ŠKODA AUTOof A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
the high pressure pump, however it must not tilt.

1. Removing and installing a V-ribbed belt and a toothed belt 53

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Turn the camshaft toothed belt pulley and high pressure pump
toothed belt pulley in their elongated holes clockwise as far as
the stop.
– Fit the toothed belt in the following order:
1- Crankshaft - toothed belt sprocket
2- Tensioning roller
3- Camshaft toothed belt pulley
4- Toothed belt pulley high pressure pump
5- Coolant pump toothed belt pulley

– Loosen nut -1- for tensioning pulley and remove rig tool -
T10265- .

Note

♦ Sheet peg of the tensioning pulley must engage in the cast

iron recess of the cylinder head.
♦ -Ignore arrow-.

WARNING

The locking screw -1- is not allowed to rest at the bottom stop
-2- of the elongated hole after the camshaft sprocket is tight‐
ened.

– Check whether the locking screw -1- is located between the

centre elongated hole and the bottom stop -2-, where neces‐
sary correct the position of the camshaft sprocket by one tooth
in a clockwise direction and put the toothed belt back into po‐
sition.

54 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Turn the eccentric of the tensioning pulley carefully with the

offset screwdriver - T10264- clockwise -arrow- until the pointer
-2- is in the centre of the base plate in front of the gap.
• The nut -1- must not turn along.
– Hold tensioning pulley in this position and tighten nut.

– Position counterholder - T10172- with -T10172/11- adapters

at the camshaft toothed belt pulley, as shown in the illustration.
– Push the counterholder anticlockwise -arrow- and keep it pre‐
tensioned.
– In this position, tighten screw -1- for camshaft toothed belt
pulley and nut -2- for high pressure pump toothed belt pulley.
♦ Specified torque: 10 Nm

Note

The toothed belt gear on the high pressure pump can only be
twisted to a limited extent. It is therefore crucial to check that the
toothed belt gear does not lie against the »stop« of the twisting
range after tightening.

– Make sure that the marking on the toothed belt gear is not flush
with the rig pin. You may need to correct the position of the
toothed belt gear of the high pressure pump by a tooth clock‐
wise and and put the toothed belt back into position.
– Remove the rig pins -3359- , -T10492- and crankshaft arrester
- T10490- and test the timing ⇒ page 55 .
Test timing:

WARNING
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Risk of destruction of the
unless authorised engine
by ŠKODA asA.aS.result
AUTO ŠKODA of AUTOtheA. toothed belt or accept any liability
S. does not guarantee
pulley jumping.
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Only rotate the crankshaft in the direction of rotation of the

engine!

– Turn the crankshaft at the screw for timing belt gear 2 turns in
the direction of running of the engine until the crankshaft is
positioned shortly before “TDC”.

1. Removing and installing a V-ribbed belt and a toothed belt 55

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Position again the crankshaft arrester - T10490- on the crank‐

shaft timing belt sprocket.
– Turn the crankshaft in the direction of rotation of the engine
until the stud -arrow- of the crankshaft arrester engages during
this rotary movement in the sealing flange.

WARNING

Adjustment error as a result of inaccurate “TDC” setting.

♦ If rotated out via “TDC”: Rotate crankshaft again by 2 turns
until it is again positioned shortly before “TDC”. Then lock
the crankshaft from the direction of rotation using the
crankshaft arrester - T10490- .

• The hub of the camshaft must be locked with the rig pin for
diesel injection pump - 3359- .

• The locking point of the hub of the high pressure pump is al‐
ways difficult to find again. A slight difference -arrow- does not
influence the engine running.

56 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

• The tensioning pulley pointer -2- must be positioned in the

centre between the pegs -1- and -3- of the base plate.

Note

A lateral offset of a maximum of 5 mm is permitted.

If the conditions are met, continue if timing is set correctly

⇒ page 57 .
If the conditions are not met, correct timing ⇒ page 57 .
Correct timing:
– If the hub of the camshaft cannot be locked, pull back the
crankshaft arrester - T10490- until the stud disconnects from
the bore.
– Turn the crankshaft slightly against the running direction of the
engine over the “TDC”.
– Now turn the crankshaft slowly in the running direction of the
engine until the hub of the camshaft can be locked.
– After locking, loosen camshaft toothed belt pulley screws.

A - Crankshaft arrester - T10490- stud is positioned to the left of

the bore:
– Turn the crankshaft in the direction of rotation of the engine
until the stud -arrow- of the crankshaft arrester engages during
this rotary movement in the sealing flange.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Tighten camshaft toothed belt pulley
unless authorised by ŠKODA toAUTO
20 Nm.A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
B - Crankshaft arrester - T10490- stud is positioned to the right of
the bore:
– First turn the crankshaft slightly against the running direction
of the engine.
– Turn the crankshaft in the direction of rotation of the engine
until the stud of the crankshaft arrester engages during this
rotary movement in the sealing flange.
– Tighten camshaft toothed belt pulley to 20 Nm.
Continued if the timing is correctly set or has been corrected:
– Remove rig pins for diesel injection pump - 3359- and crank‐
shaft arrester - T10490- .
– Turn the crankshaft at the screw for timing belt gear 2 turns in
the direction of running of the engine until the crankshaft is
positioned shortly before “TDC”.
– Repeat timing test ⇒ page 55 .

1. Removing and installing a V-ribbed belt and a toothed belt 57

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

WARNING

Risk of engine damage.

♦ The diesel injection pump rig pin - 3359- must not be used
as a counterholder for tightening the camshaft toothed belt
pulley.

– If it is now possible to lock the camshaft hub, tighten screws

-1- for toothed belt pulley -Pos. 8- ⇒ page 42 to the end position
using counterholder - T10172- with adapters -T10172/11- .
– Tighten the nuts -2- for the toothed belt gear, high pressure
pump -Pos. 4- ⇒ page 309 to the end position, to do so, use
the counterholder - T10051- .
– Repeat timing test ⇒ page 55 .
Assembling
Assembling is performed continuing in the reverse order, while
paying attention to the following:

Note

♦ Replace gasket.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

– Tighten fixing screw -1-.

Tightening torques
♦ Summary of components - toothed belt guard
⇒ “1.6 Summary of components - toothed belt guard”,
page 40
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Assembly overview - toothed belt drive
⇒ “1.7 Assembly overview - toothed belt drive”, page 42

58 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Removing and installing sealing

flange and flywheel

2.1 Summary of components - sealing flange belt pulley side

1 - Sealing flange on the belt

pulley side
❑ with shaft sealing ring
for crankshaft
❑ replace after removal
❑ removing and installing
⇒ page 60
2 - Screw
❑ Tightening torque and
tightening order
⇒ page 59
3 - Crankshaft - toothed belt
sprocket
❑ there must not be any oil
present on the contact
surface between the
toothed belt sprocket
and the crankshaft
❑ can be installed only in
one position
4 - Screw
❑ Tightening torque
-Pos. 1- ⇒ page 42

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Sealing flange on the belt pulleyunless
sideauthorised
- tightening
by ŠKODA torque
AUTO A. and tight‐AUTO A. S. does not guarantee or accept any liability
S. ŠKODA
ening order with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Tighten screws in steps in the given sequence:

Stage Screws Tightening torque
1. -1 … 10- by hand as far as the stop
2. -1 … 6- crosswise in steps up to 13 Nm
3. -7 … 10- 13 Nm

2. Removing and installing sealing flange and flywheel 59

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.2 Removing and installing the sealing

flange on the belt pulley side
Special tools and workshop equipment required
♦ Counterholder - T30004 (3415)- or counterholder for toothed
belt sprocket - MP 1-310 (3099)-
♦ Assembly tool - T10053-
♦ Protective goggles and gloves
♦ Sealant remover gasket stripper (bearing code GST, bearing
article no. R 34402), manufacturer Retech s.r.o.
♦ Cleaning and degreasing agent , e.g. -D 009 401 04-
♦ Silicone sealant ⇒ ETKA - Electronic catalogue of original
parts
Removing
– Remove the front right wheelhouse liner ⇒ Body Work; Rep.
gr. 66 .
– Removing toothed belt ⇒ page 49 .
– Remove crankshaft - toothed belt sprocket, to this end lock
toothed belt sprocket with counterholder - T30004 (3415)- or
counterholder - MP 1-310- .
– Removing the oil pan ⇒ page 123 .
– Unscrew the remaining screws and carefully loosen the seal‐
ing flange from the bonding.
Install
Install in the reverse order of removal. When doing this, note the
following:

WARNING

Wear protective gloves when working with sealant

Protectedand greaseCopying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
remover! unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove residual sealant from the sealing surfaces on sealing

flange, cylinder block and on the oil pan with chemical sealant
remover.
– Degrease the sealing surfaces.

– Install -T10053/1- guide bushing on the crankshaft stub.

Note

Pay attention to the use by date on sealant.

60 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Cut off nozzle on tube at front marking (∅ of nozzle approx. 2

mm).

– Apply sealant bead -arrow- onto the clean sealing surface of

the sealing flange, as shown in the illustration.
• Thickness of sealant bead: 2 … 3 mm.

Note

♦ The sealant bead must not be thicker than 3 mm otherwise

excess sealant may get into theProtected
oil pan and clogg
by copyright. the
Copying for strainer
private or commercial purposes, in part or in whole, is not permitted
in the oil suction pipe. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ The sealing flange must be installed within 5 minutes after ap‐
plying the sealant.

– Slide new sealing flange over the guide sleeve.

• The fit pins will engage with the bores in the cylinder block
during this process.
– Remove guide bushing.
– Tighten sealing flange screws ⇒ page 59 .
– Installing the oil pan ⇒ page 123 .
– install (set the timing) ⇒ page 52 .
Tightening torques
♦ Sealing flange on the belt pulley side - tightening torque and
tightening order
⇒ Fig. ““Sealing flange on the belt pulley side - tightening tor‐
que and tightening order”“ , page 59
♦ Screw for crankshaft toothed belt gear -Pos. 1- ⇒ page 42
♦ Summary of components - front wheelhouse liner ⇒ Body
Work; Rep. gr. 66

2.3 Summary of components - gearbox side summary of components and fly‐

wheel

2. Removing and installing sealing flange and flywheel 61

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - 60 Nm + torque a further 90°

(1/4 turn)
❑ replace after removal
2 - Flywheel
❑ Inspect proper opera‐
tion of two-mass fly‐
wheel ⇒ Vehicle diag‐
nostic tester
❑ removing and installing
⇒ page 69
❑ can be installed only in
one position
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
3 - Rotor
❑ for engine speed sender
- G28-
❑ removing and installing
⇒ “2.4 Removing and in‐
stalling sealing flange
on gearbox side”,
page 63
4 - Engine speed sender -
G28-
❑ Summary of compo‐
nents ⇒ page 385
5 - 4.5 Nm
6 - Fit pin
❑ Qty. 2
7 - Intermediate plate
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ do not damage or bend unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
during assembly work with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ installing ⇒ page 62
8 - Sealing flange on the gearbox side
❑ with gasket
❑ Renew. ⇒ page 63 .
9 - Bolt
❑ Tightening torque and tightening order ⇒ page 63

Installing intermediate plate

– Insert intermediate plate on sealing flange -top arrow- and
push onto the dowel sleeves -bottom arrows-.

62 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Sealing flange on the gearbox side - tightening torque and tight‐

ening order
– Tighten screws in steps in the given sequence:
Stage Screws Tightening torque
1. -1 … 6- by hand as far as the stop
2. -1 … 6- crosswise in steps up to 13 Nm

2.4 Removing and installing sealing flange

on gearbox side
Special tools and workshop equipment required
♦ Assembly tool - T10134-
♦ Depth gauges , e.g. -VAS 6082-
♦ 3x screw M6x35
♦ 2x screw M7x35
Press out sealing flange with rotor
• Gearbox removed.
– Remove the flywheel ⇒ page 69 .

Note

For a clearer illustration, see the following work sequences while

the engine is removed.

– Unhook intermediate plate at the sealing flange and dowel

sleeves -arrows-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Turn the crankshaft at the screw for toothed belt pulley until
the crankshaft is positioned on “TDC” as shown in the illustra‐
tion.
– Remove sump ⇒ page 123 .
– Remove engine speed sender - G28- ⇒ page 389 .

2. Removing and installing sealing flange and flywheel 63

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -1 … 6- for sealing flange.

Note

The sealing flange is pressed together with the crankshaft rotor .

– To press out, insert 3 screws M6x35 -arrows- into the sealing

flange alternately by a maximum of 1/2 turns each.
– Remove sealing flange with rotor
Press in sealing flange with rotor

Note

♦ The sealing flange with a PTFE seal is equipped with a sealing

lip support ring. This support ring serves as a fitting sleeve and
must not be removed prior to installation.
♦ Sealing flange and sender wheel must not be separated or
turned after removal from packaging.
♦ The rotor is held in its installation position on the assembly
device - T10134- by a locating pin.
♦ Sealing flange and oil seal form one unit and must only be
renewed together with the sender wheel.
♦ The assembly device - T10134- is held in its position relative
to the crankshaft by a guide pin that is inserted into a hole in
the crankshaft.

Assembly of the assembly device - T10134-

A - Clamping surface
B - Hexagon nut
C - Assembly housing
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
D - Locating pin unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
E - Hexagon socket head bolt
F - Guide pin for diesel engines (black knob)
G - Guide pin for petrol engines (red knob)

64 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

A - Mount sealing flange with rotor on the assembly device -

T10134- :
– Screw on hexagon nut -B- until just before it touches the
clamping surface -A- of the threaded spindle.

– Grip assembly device - T10134- on clamping surface -A- of

the threaded spindle in a vice.
– Push assembly cup -C- down so that it rests on the hexagon
nut -B- -arrow-.
• The inside of the assembly device and assembly cup must be
at the same level.

– Remove securing clip -arrow- from new sealing flange.

Note

The sender wheel must not be taken out of the sealing flange or
twisted.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
• Locating hole -A- onsender wheelto -C-
with respect must align
the correctness with marking
of information in this document. Copyright by ŠKODA AUTO A. S.�
-B- on sealing flange.
– Place sealing flange with front side facing down on a clean
level surface.

2. Removing and installing sealing flange and flywheel 65

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Press the sealing lip supporting ring -A- down -arrows- until it
rests on the level surface.

• Upper edge of sender wheel and front edge of sealing flange

must align -arrows-.

– Place sealing flange with front side facing downwards onto

assembly tool - T10134- so that locating pin -B- can be inser‐
ted in sender wheel bore -A-.
• The sealing flange must lie flat on the assembly device.

– When tightening the knurled screws -A- press the sealing

flange and sealing lip supporting ring -B- on the surface of the
assembly device - T10134- in such a way that the positioning
pin can no longer slide out of the rotor hole.
• Only the two top right knurled screws - the left knurled screw
does not fit into the sealing flange thread.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
• The rotor must remain
unless authorised by ŠKODA fixed
AUTOin the
A. S. assembly
ŠKODA AUTO A. S.device
does not while the
guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
sealing flange is being mounted.

66 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

B - Mount assembly tool - T10134- with sealing flange on crank‐

shaft flange:
• Crankshaft flange free from oil and grease.
• Engine on “TDC”.
– Screw hexagon nut -B- on until it reaches end of threaded
spindle.
– Press threaded spindle of assembly tool - T10134- in
-direction of arrow-, until hexagon nut -B- lies against assem‐
bly housing -A-.

– Align flat side of assembly housing to the cylinder block sealing

surface on the oil sump side.
– Secure assembly device - T10134- to crankshaft flange - to do
so insert hexagon socket head bolts -A- by approximately 5
threads at the crankshaft flange.

– Insert 2 screws M7x35 -Pos. A- into the cylinder block for the
sealing flange guide.

C - Bolt assembly tool - T10134- onto the crankshaft flange:

– Move the assembly cup -C- by hand in the
-direction of the arrow- until the sealing lip supporting ring
-B- rests on the crankshaft flange -A-.

Protected by copyright. WARNING

Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Risk of mix-ups.
♦ The guide bolt for petrol engines (red handle) -F- must not
be fitted into the threaded hole of the crankshaft.

– Push guide pin for diesel engines (black handle) -D- into the
crankshaft bore; this puts the rotor into the final installation
position.
– Tighten both hexagon socket head bolts of the assembly de‐
vice by hand.
– Screw hexagon nut -E- onto threaded spindle by hand until it
lies against assembly housing -C-.

2. Removing and installing sealing flange and flywheel 67

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

D - Press sender wheel onto crankshaft flange using assembly

device - T10134-
– Tighten hexagon nut for the assembly device - T10134- to 35
Nm.
• After hexagon nut is tightened to 35 Nm, a small air gap must
still be present between cylinder block and sealing flange.

E - Inspect the installation position of the rotor on the crankshaft:

– Screw in hexagon nut -E- up to the end of the threaded spindle.
– Release screws -A- from the cylinder block.
– Release knurled screws -B- from the sealing flange.
– Unscrew hexagon socket head bolts.
– Unscrew assembly device - T10134- from the crankshaft
flange - to do so, unscrew the hexagon socket head bolts from
the crankshaft flange.
– Remove assembly tool - T10134- .
– Remove sealing lip support ring.

– Position depth gauges - VAS 6082- at the crankshaft flange.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Measure distance
unless between
authorised by ŠKODA AUTO crankshaft
A. S. ŠKODAflange
AUTO A. -A- and
S. does not rotor
guarantee or accept any liability
-B-. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

• Specified value: Dimension -a- = 0.5 mm

– If dimension -a- is too small, press rotor down ⇒ page 69 .
– When the specified value has been reached, perform the re‐
maining assembly ⇒ page 69 .

68 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

F - Pressing down the rotor:

– Secure assembly device - T10134- to crankshaft flange - to do
so tighten hexagon socket head bolts -A- by hand.
– Press the assembly tool against the sealing flange by hand.

– Screw hexagon nut -E- onto threaded spindle by hand until it

lies against assembly housing -C-.

– Tighten hexagon nut for the assembly device - T10134- to 40

Nm.
– Checking sender wheel installation position on crankshaft
again ⇒ page 68 .
– If dimension “a” is still too small, tighten assembly device -
T10134- hexagon nut to 45 Nm.
– Checking sender wheel installation position on crankshaft
again ⇒ page 68 .
Assembling together:
Assembling is performed in the reverse order, while paying at‐
tention to the following:
– Install sump ⇒ pageProtected
123 .by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Installing intermediate
withplate
respect⇒
to page 62 . of information in this document. Copyright by ŠKODA AUTO A. S.�
the correctness

– Install flywheel ⇒ page 69 .

Tightening torques
♦ Sealing flange on the gearbox side - tightening torque and
tightening order
⇒ Fig. ““Sealing flange on the gearbox side - tightening torque
and tightening order”“ , page 63
♦ Summary of components - preheating system
⇒ “1.1 Summary of components - preheating system ”,
page 385

2.5 Removing and installing flywheel

Special tools and workshop equipment required
♦ Counterholder - MP1-223 (3067)-

2. Removing and installing sealing flange and flywheel 69

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing
• Gearbox removed.

WARNING

Risk of destruction of the flywheel.

♦ Do not unscrew screws -B- using a pneumatic power
wrench or impact wrench - unscrew by hand.
♦ When unscrewing screws, ensure that no screw head is
present on the flywheel.
♦ Rotate flywheel -A- so that the screws -B- are positioned
in the centre of the bores -arrows-.

– Insert counterholder - MP1-223 (3067)- into the bore on the

cylinder block -Pos. B-, loosen flywheel screws.
– Release screws and remove flywheel.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Insert counterholder - MP1-223 (3067)- into the bore on the

cylinder block -Pos. A-.
Tightening torques
♦ Summary of components - gearbox side summary of compo‐
nents and flywheel
⇒ “2.3 Summary of components - gearbox side summary of
components and flywheel”, page 61

70 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 Crankshaft, Piston and Conrod

3.1 Summary of components - crankshaft

Note

♦ The summary of components refers exclusively to engines without balancing shafts.

♦ On engines with balancing shafts, the crankshaft must not be removed. The balancing shaft system must
not be disassembled.

1 - Cylinder block
2 - Bearing shell
❑ for cylinder block with lu‐
bricating groove
❑ replace used bearing
shells
3 - Toothed belt pulley
❑ for oil pump drive
❑ not available individual‐
ly as a spare part
4 - Bearing shell
❑ for bearing cap without
lubricating groove
❑ replace used bearing
shells
5 - 65 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
6 - Bearing caps
❑ Bearing cover 1: Belt
pulley side
❑ bearing cap 3 with re‐
cesses for thrust wash‐
ers
❑ Fitting position: retain‐
ing lugs of the bearing
shells in the cylinder
block/bearing cap must
be on top of one another
7 - Thrust washer
❑ for bearing 3
❑ different version for cyl‐
inder block and bearing cap Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ pay attention to locating element with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
8 - Crankshaft
❑ for vehicles with manual gearbox, no needle bearing must be installed; remove needle bearing if nec‐
essary ⇒ page 72
❑ for vehicles with dual clutch gearbox, needle bearing must be installed in the crankshaft; install needle
bearing if necessary ⇒ page 72
❑ New axial clearance: 0.07…0.17 mm
Wear limit: 0.37 mm

3. Crankshaft, Piston and Conrod 71

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ Crankshaft bearing journals ∅ 54.00 mm
❑ Rod bearing journals (1.6 l engine): ∅ 47.80 mm
❑ Rod bearing journals (2.0 l engine): ∅ 50.90 mm

3.2 Replace the needle bearing in the crank‐

shaft

Note

♦ For vehicles with manual gearbox, no needle bearing must be

installed.
♦ For vehicles with dual clutch gearbox, needle bearing must be
installed in the crankshaft; ⇒ ETKA - Electronic Catalogue of
Original Parts .

Special tools and workshop equipment required

♦ Interior extractor - Kukko 21/2-
♦ Countersupport - Kukko 22/1-
♦ Centering mandrel - T30029 (3176)-
Removing
• Gearbox removed.
– Pull out needle bearing with interior extractor - Kukko 21/2-
and countersupport - Kukko 22/1- .
Install
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Note with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Labelled side of needle bearing must be legible in the installed

condition.

– Drive in the needle bearing using the centering pin - T30029

(3176)- .

72 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation depth, dimension -a- = 2 mm.

3.3 Assembly overview - piston and conrod

1 - 30 Nm + torque a further 90°

(1/4 turn)
❑ replace after removal
❑ Oil threads and contact
surface.
2 - Conrod bearing cap
❑ Check fitting position
❑ as a result of the con‐
rods separated in the
cracking process, the
conrod bearing cap fits
only in one position and
only to the relevant con‐
rod
❑ Mark assignment to the
cylinder in colour -B-
❑ Fitting position: mark‐
ings -A- point toward
belt pulley side
3 - Bearing shells
❑ Fitting position
⇒ page 76
❑ replace used bearing
shells
❑ Pay attention to version:
top bearing shell (to‐
wards the piston) must
be in long wearing ma‐
terial. Distinguishing
feature of new bearing
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
shells:
with respect to theblack marking
correctness on in this document. Copyright by ŠKODA AUTO A. S.�
of information
contact surface near the
separation point
❑ pay attention to correct
position
4 - Conrod
❑ Renew as set only.
❑ Mark assignment to the conrod bearing cap and to the cylinder in colour -B-
❑ Fitting position: markings -A- towards belt pulley side
❑ with cracked conrod bearing cap
❑ separate new conrod ⇒ page 79
❑ Axial play wear limit: 0.37 mm

3. Crankshaft, Piston and Conrod 73

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

5 - Pressure relief valve, 27 Nm

❑ replace without sealant
❑ removing and installing ⇒ page 77
6 - Oil injection nozzle
❑ for piston cooling
❑ removing and installing ⇒ page 77
7 - Circlip
❑ Qty. 2
❑ replace after removal
8 - Piston pin
❑ removing and installing ⇒ “3.4 Removing and installing the piston”, page 77
9 - Piston
❑ with combustion chamber
❑ replace piston if there is any sign of crack formation on the piston crown or piston body
❑ Mark the installation position and the assignment to cylinder ⇒ page 76
❑ removing and installing ⇒ page 77
❑ Checking piston and cylinder bore ⇒ page 75
❑ Measure piston projection in “TDC” ⇒ page 78
❑ Observe part number ⇒ ETKA - Electronic Catalogue of Original Parts
10 - Compression rings
❑ Measure end gap ⇒ page 74
❑ Measure vertical gap ⇒ pageProtected
75 by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ use commercially available unless
piston ring pliers
authorised by ŠKODA forAUTO
removing and
A. S. ŠKODA installing
AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ Fitting position: Identification “TOP” or labelled side for piston crown
❑ Offset gaps by 120°.
11 - Oil scraper ring
❑ Measure end gap ⇒ page 74
❑ Measure vertical gap ⇒ page 75
❑ use piston ring pliers for removing and installing
❑ Fitting position: Identification “TOP” or labelled side for piston crown
❑ Offset joint 120° to bottom compression ring

Checking piston ring gap

Special tools and workshop equipment required

♦ Feeler gauges
– Push the piston ring into the bottom cylinder opening at right
angles to the cylinder wall from above to about 15 mm from
the cylinder edge. To insert, use a piston without piston ring.

74 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Piston ring New Wear limit

(dimensions in mm)
1. Compression ring 0.30 … 0.40 0.55
2. Compression ring 0.20 … 0.45 0.95
Oil scraper ring 0.25 … 0.50 0.75
Checking ring-to-groove clearance

Special tools and workshop equipment required

♦ Feeler gauges
– Clean before inspecting the annular grooves of the piston.
Piston ring Wear limit
(dimensions in mm)
1. Compression ring 0.08
2. Compression ring 0.08
Oil scraper ring 0.08
Checking piston
Special tools and workshop equipment required
♦ External micrometer
– Measure about 15 mm from the lower edge, offset at right an‐
gles to the piston pin shaft.
• Maximum deviation from nominal dimension: 0.04 mm.
– Check piston for cracks, wear of the coating on the piston body
and oil coking.
∅ piston mm
Nominal dimen‐ 1.6 l 79.42 1)
sion
2.0 l
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
80.92 1)by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
unless authorised
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• 1) Dimensions with coating (thickness 0.02 mm). The coating
wears off.

Checking cylinder bores

Special tools and workshop equipment required

♦ Internal precision measuring instrument

3. Crankshaft, Piston and Conrod 75

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Measure cylinder at 3 points crosswise in transverse direction

-A- and lengthwise -B-.
– Check cylinder bore for wear of the honing surface, scratches
and other abnormalities.
∅ cylinder mm
Nominal dimen‐ 1.6 l 79.5
sion
2.0 l 81.0

Note

Cylinder bores must not be measured when cylinder block is

mounted on engine and gearbox support - VAS 6095- , as meas‐
urements may be incorrect.

Fitting position of piston and assignment of piston to cylinder

WARNING

Risk of damaging the piston crown.

♦ For re-installation, mark the assignment in colour on the
piston crown of cylinders that have already been used.
Piston crown not by centre punch, scratch, nick or similar
mark.

• Arrow on the piston crown to the belt pulley side -arrow-.

Installation position of the bearing shells in the conrods

– Insert bearing shells centrally in the conrod and conrod bear‐
ing cap.
• Dimension -a- = 2.5 mm

76 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Oil spray nozzle and pressure relief valve

1- Screw with pressure relief valve, 27 Nm
2- Oil spray nozzle (for cooling piston)
• Fitting position: Align the guide edge of the oil injection nozzle
to the area of the cylinder block being worked on.

WARNING

Risk of damaging the oil injection nozzles.

♦ Do not bend oil injection nozzles.
♦ Check oil injection nozzles after reinstalling the pistons.
♦ Replace the oil injection nozzles if they are bent.

3.4 Removing and installing the piston

Special tools and workshop equipment required
♦ Drift - VW 222 A-
♦ Piston ring tensioning strap
Removing
• Engine secured to engine and gearbox mount ⇒ page 22 .
– Remove cylinder head ⇒ page 88 .
– Remove oil pump ⇒ page 126 .
– For re-installation, mark the installation position and assign‐
ment of the conrod bearing cap to the cylinder head and to the
conrod -Pos. 2- ⇒ page 73 .
– Unscrew the conrod bearing cap.
– Pull out the piston with conrod upwards.

Note

In case of tightness of the piston pin, heat piston to approximately

60 °C.

– Remove the circlip from the bore of the piston pin.

– Drive off piston pin with a drift - VW 222 A- .
Install
Installation is carried out in the reverse order. When installing,
note the following: Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Oil the contact surfaces of the bearing shells.

– Install piston with piston ring tensioning strap.
Fitting position:
• Piston ⇒ page 76 .

3. Crankshaft, Piston and Conrod 77

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

• Bearing shells in the conrods ⇒ page 76 .

– Install the conrod bearing cap according to marking.
– Install oil pump ⇒ page 126 .
– Install cylinder head ⇒ page 88 .
Tightening torques
♦ Assembly overview - piston and conrod
⇒ “3.3 Assembly overview - piston and conrod”, page 73

3.5 Checking piston projection in TDC

Note

When installation a new piston or engine part, you must check the
piston protrusion in the “TDC”.

Special tools and workshop equipment required

♦ Measuring tool for liner pretension - MP 1-107-
Test procedure
– Secure measuring device for bushing pretensioning - MP
1-107- to the cylinder block as shown in the illustration.
– Measure the projection for each cylinder at 2 points.
When fitting new pistons or a partial engine, check the piston pro‐
jection in TDC on all pistons.
If different values are measured during the projection measure‐
ment of the piston, the greatest dimension applies for the seal
assignment.
Depending on the piston projection fit the relevant cylinder head
seal in accordance with the table below.
Piston projection over cylinder Identification
block top side Holes
mm
0.91 … 1.00 1
1.01 … 1.10 2
1.11 … 1.20 3

78 Rep. gr.13 - Crankshaft group

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Identification of the cylinder head gasket

♦ Part number = -arrow 1-
♦ Holes -arrow 2- (ignore)
♦ Holes -arrow 3-

Note

If different values are measured during the projection measure‐

ment of the piston, the greatest dimension applies for the seal
assignment.

3.6 Separating new conrod

It can happen that on new conrods, the provided separation point
is not completely cracked. If the conrod bearing cap cannot be
removed by hand, then proceed as follows:
– Tension the conrod slightly in a vice fitted with an aluminium
protective jaw, as shown in the illustration.

Note

♦ Only tension the conrod slightly in order to avoid damage on

the conrod.
♦ The conrod is clamped below the broken line.

– Unscrew both screws -arrows- by approx. 5 turns.

– Using a plastic hammer, carefully knock against conrod bear‐

ing cap in -direction of arrow- until it is loose.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

3. Crankshaft, Piston and Conrod 79

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

15 – Cylinder head, valve gear

1 Removing and installing cylinder
head

Note

♦ Cylinder heads with cracks between the valve seats may con‐
tinue to be used without any reduction in the life time provided
the cracks are slight and max. 0.5 mm wide.
♦ It is not permissible to rework the cylinder heads of diesel en‐
gines.
♦ Replace self-locking nuts, gasket rings, gaskets and O-rings.
♦ Replace cylinder head bolts and screws which have been
tightened to a torquing angle.
♦ Oil contact surfaces between the roller rocker finger and cam
slideway.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .
♦ If the cylinder head or the cylinder head gasket is replaced,
the system must be completely filled with fresh coolant
⇒ page 139 .

1.1 Assembly overview - cylinder head cover

80 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Seal
❑ replace if damaged or
leaking
2 - Cylinder head cover
❑ removing and installing
⇒ page 82
3 - O-ring
❑ replace after removal
4 - Plug
5 - Bracket
❑ for electrical cables
6 - 8 Nm
7 - Grommet
❑ in the cylinder head cov‐
er
8 - Clamping claw
9 - Bolt
❑ Tightening torque
-Pos. 8- ⇒ page 295
10 - O-ring
❑ replace after removal
11 - Hose
❑ for crankcase ventila‐
tion
❑ to remove, press re‐
lease buttons
12 - Fuel return line
13 - O-ring
❑ replace after removal
14 - Injection unit
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Observe rules
with respect forcorrectness
to the cleanliness ⇒ page
of information in this 6
document. Copyright by ŠKODA AUTO A. S.�

❑ Summary of components ⇒ page 295

15 - O-ring
❑ replace after removal
16 - Heat-protection seal
❑ replace after removal
17 - Sealing ring
❑ for injection unit
❑ replace after removal ⇒ page 84
18 - Vacuum hose
19 - Screw cap
20 - Seal
❑ for cap
21 - Sealing sleeve
22 - Bolt
❑ replace if the seal has been damaged

1. Removing and installing cylinder head 81

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ Tightening torque and tightening order ⇒ page 82

Cylinder head cover - tightening torque and tightening order

– Tighten the screws for the cylinder head cover in the sequence
-1…7- to 9 Nm.

1.2 Removing and installing cylinder head

cover
Special tools and workshop equipment required
♦ Extension SW 17 from the set of tools - T10395-
Removing

Note

Fit the heat protection sleeve on again in the same place when
installing.

– Remove engine cover at the top ⇒ page 9 .

– Unscrew exhaust temperature sender 3 - G495- -Pos. 2- with
a toolbyfrom
Protected theCopying
copyright. tool set SWor17
for private - T10395-
commercial . in part or in whole, is not permitted
purposes,
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– with
Unscrew
respect toscrew -3-, expose
the correctness thein pipeline
of information and
this document. pushbyitŠKODA
Copyright to theAUTO
side.A. S.�

Note

-Do not pay attention to the position 1-.

– Unlock catches -arrows-, unhook and push top toothed belt

guard -1- to the right side
– Remove the injection units ⇒ page 303 .

82 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Press release buttons on the hose -1- for crankcase ventila‐

tion, remove hose from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Slacken hose clamp -3-, remove air guide pipe from air mass
meter - G70- .
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CRVC, CUPA

– Open heat protection sleeve -1-.

– Disconnect electrical plug connections -3, 4, 5-, expose elec‐
tric wiring loom.
– Unscrew screw -2-, lay bracket with differential pressure send‐
er - G505- to the rear.
For vehicles with engine identification characters CRKB

– Open heat protection sleeve -1-.

– Disconnect electrical plug connections -3, 5, 6- expose electric
wiring loom.
– Release screw -2-.
– Separate electrical plug connection -4-.

– Detach vacuum hose -arrow- and put to one side.

– Place the bracket with the differential pressure indicator to the
rear.
Continued for all vehicles

1. Removing and installing cylinder head 83

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Detach vacuum hose -arrow-.

– Slacken the screws for the cylinder head cover in the se‐
quence -7 … 1- and release them.
– Remove cylinder head cover.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Renew O-ring.
♦ Replace gasket and screws for cylinder head cover if dam‐
aged or leaking.

– Connect vacuum hose ⇒ page 279 .

Tightening torques
♦ Cylinder head cover - tightening torque and tightening order
⇒ Fig. ““Cylinder head cover - tightening torque and tightening
order”“ , page 82
♦ Summary of components - toothed belt guard
⇒ “1.6 Summary of components - toothed belt guard”,
page 40
♦ Summary of components - exhaust gas turbocharger with
component parts
⇒ “1.1 Exhaust gas turbocharger with
Protected component
by copyright. parts
Copying for private- or
Sum‐
commercial purposes, in part or in whole, is not permitted
mary of components”, pageunless
265 authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370
♦ Summary of components - injection units (injectors)
⇒ “2.1 Summary of components - injection units (injectors)”,
page 295

1.3 Replacing gasket rings for injection units

Special tools and workshop equipment required
♦ Driver - 3390-
♦ Set of tools for FSI engines - T10133-
♦ Gasket ring extractor - T40195-
Procedure
– Remove injection unit concerned ⇒ page 303 .

84 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Insert sealing ring extractor - T40195- into the sealing ring

-1-.
– Position hammer -T10133/3- with the adapter -T10133/2- at
the sealing ring extractor, as shown in the illustration, and pull
out upwards.

– Press in the new gasket ring for the injection unit using the
driver - 3390- and a short extension -1- from the outside of the
cover up to the stop.

1.4 Assembly overview - cylinder head

1. Removing and installing cylinder head 85

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Cylinder block
2 - Cylinder head gasket
❑ Renew.
⇒ “1.5 Removing and in‐
stalling cylinder head”,
page 88 .
❑ Identification of the cyl‐
inder head gasket
⇒ page 87
❑ change coolant and en‐
gine oil after replace‐
ment
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
3 - Cylinder head
❑ removing and installing
⇒ page 88
❑ lay removed cylinder
head on a foam pad on‐
ly, otherwise the glow
plugs may be damaged
❑ check for distortion
⇒ page 87
❑ must not be reworked
❑ before installing, check
whether both dowel
sleeves for centering
the cylinder head at the
cylinder block are
present
❑ change coolant and en‐
gine oil after replace‐
ment
❑ Observe part number ⇒
ETKA - Electronic Catalogue of Original Parts
4 - Fit pin
❑ for camshaft housing
5 - Bolt
❑ replace after removal
❑ loosening order ⇒ page 94
❑ Tightening torque and tightening order ⇒ page 88
6 - 20 Nm
7 - Engine suspension eye
8 - Distance ring
❑ replace if damaged
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
9 - O-ring unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ replace after removal
❑ Moisten with coolant
10 - Coolant temperature sender - G62-
❑ removing and installing ⇒ page 152
11 - Double screw
❑ Tightening torque -Pos. 4- ⇒ page 148

86 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

12 - Fit pin
❑ for camshaft housing
13 - Inlet connections
❑ for coolant hoses
14 - 10 Nm
15 - Sealing ring
❑ replace after removal
16 - Fit pin
❑ for intake manifold with charge air cooler
17 - Dowel sleeves

Checking cylinder head for distortion

– Inspect cylinder head at several points for distortion using a
500 mm knife-edge straightedge - VAS 6075- and feeler
gauge.
• Maximum permitted distortion: 0.1 mm.

Note

Cylinder heads for TDI engines must not be reworked.

Identification of the cylinder head gasket

♦ Part number = -arrow 1-
♦ Holes -arrow 2- (ignore)
♦ Holes -arrow 3-

Note

Differing thicknesses of cylinder head gaskets are inserted ac‐

cording to the piston projection ⇒ page 78 . If only the cylinder
head gasket is replaced, install a new cylinder head gasket with
the same identification.

1. Removing and installing cylinder head 87

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Cylinder head - tightening torque and tightening order

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Tighten screws in steps in the given sequence:

Stage Screws Tightening torque/torquing angle
1. -1 … 10- 30 Nm
2. -1 … 10- 65 Nm
3. -1 … 10- Turn 90° further
4. -1 … 10- Turn 90° further

1.5 Removing and installing cylinder head

Special tools and workshop equipment required
♦ Removal tool for inner lining of the door panel - MP8-602/1-
♦ Hose clip pliers - VAS 6362-
♦ Sealant remover gasket stripper (bearing code GST, bearing
article no. R 34402), manufacturer Retech s.r.o.
♦ Protective goggles and gloves

1.5.1 Removing
Requirements Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• Engine temperature should not exceed 35°, because the cyl‐
inder head could be twisted when slackening the screws.
• The pistons must not be in TDC.

Caution

When undertaking all installation work, particularly in the en‐

gine compartment due to its cramped construction, please
observe the following:
♦ Lay lines of all kinds (e.g. for fuel, hydraulic fluid, cooling
fluid and refrigerant, brake fluid, vacuum) and electrical
lines in such a way that the original line guide is re-estab‐
lished.
♦ To avoid damage to lines/wiring, ensure sufficient clear‐
ance to all moving or hot components.
♦ Fit all heat protection sleeves on again in the same place
when installing.

Observe all safety measures and notes for assembly work on the
fuel supply and injection system, at the charge air system and
observe as well the rules for cleanliness ⇒ page 3 .
– Remove engine cover at the top ⇒ page 9 .
– Remove front top coolant pipe ⇒ page 157 .
– Remove rear coolant pipe ⇒ page 164 .

88 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove left coolant pipe ⇒ page 163 .

– Remove pre-exhaust pipe ⇒ page 349 .
– Remove the toothed belt from the camshaft ⇒ page 47 .
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CRVC, CUPA
– Open heat protection sleeve -1-.
– Take electrical plug connection-4 - out of the holder, discon‐
nect and expose electric cable.
– Disconnect electrical plug connections -3, 5-, expose electric
wiring loom:
– Unscrew screw -2-, lay bracket with differential pressure send‐
er - G505- to the rear.
For vehicles with engine identification characters CRKB

– Open heat protection sleeve -1-.

– Disconnect electrical plug connections -3, 5, 6- expose electric
wiring loom.
– Release screw -2-.
– Separate electrical plug connection -4-.

– Press release buttons on the hose -1- for crankcase ventila‐

Note

-Do not pay attention to the position 3-.

1. Removing and installing cylinder head 89

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -arrows- and remove pre-volume tank -1-.

– Loosen hose clamp -1-, remove coolant hose.

– Unscrew screw -2-, remove screw -3- and swivel coolant line
to the side.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Expose the following plug connections and electric cables:
2 - for exhaust gas temperature sender 4 - G648-
3 - for exhaust gas temperature sender 3 - G495-
– Take electrical plug connection-4- for lambda probe - G39- out
of the holder, disconnect and expose electric cable.
Vehicles with four-wheel drive
– Remove radiator for exhaust gas recirculation ⇒ page 381 .

Vehicles with front-wheel-drive

– Press heat protection sleeve to the side, disconnect electrical
plug connection -5-.
– Loosen hose clamp -3-, remove air guide hose.
– Loosen hose clamp -4-, remove coolant hose.
– Unscrew screw -1-, loosen screw -2-.

Note

-Do not pay attention to the position 6-.

Continued for all vehicles

90 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen screw -1- and remove clamping sleeve.

– Slacken the double screw -2-, press coolant pipe backwards
slightly.
– Unscrew screws -arrows-, push exhaust gas cleaning module
backwards - do the same to the exhaust gas recirculation
cooler on vehicles with front-wheel-drive.

– Release nut -2- and remove union nut -4-.

– Release screws -3, 5-, remove oil return pipe.

Note

-Do not pay attention to the position 1-.

Vehicles fitted with auxiliary heating

– Raise holding clamps -1- and undo hose clamp -3-, remove
coolant hoses.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Release nuts -arrows-,
unless remove
authorised by coolant
ŠKODA AUTO pipe.AUTO A. S. does not guarantee or accept any liability
A. S. ŠKODA
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Continued for all vehicles

1. Removing and installing cylinder head 91

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screw -2-, loosen screws -1, 3, 4- only.

For vehicles with engine identification characters CRKB

– Separate electrical plug connections -1, 3-.

– Loosen hose clamp -2-.
Continued for all vehicles

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Disconnect and expose electrical plug connections:
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1 - for charge air temperature sender after charge air cooler -

G811-
3 - for charge pressure sender - G31-
4 - for Intake air temperature sender - G42-
5 - for throttle valve control unit - J338-
– Unscrew hose clamps -2, 7-, remove coolant hose -6-.

– Release screw -1- for guide pipe for oil dipstick.

– Unscrew screws -2, 3- for intake manifold holder.
For vehicles with engine identification characters CRKB
– Remove throttle valve module - J338- ⇒ page 327 .
Continued for all vehicles
– Remove the camshaft housing ⇒ page 104 .

92 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connection -3- and remove from

cover -2-.
– Unscrew screw -1-, remove cover.

– Unlock catch -arrow-, remove vacuum hose -1-.

– Disconnect vacuum hose -2-.
– Release screw -3-.

– Disconnect the electrical plug connection -2- for coolant tem‐

perature sender - G62- .
– Loosen hose clamp -1-, remove coolant hose.
– Disconnect vacuum hose -3-.

– Disconnect electrical plug connections at the glow plugs

⇒ page 386 .
– Lay electrical wiring loom to the side.

1. Removing and installing cylinder head 93

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release the cylinder head bolts in the order -1 … 10-.

Note

A 2nd mechanic is required for removing the cylinder head.

– Swivel the cylinder head to the left out of the rear toothed belt
guard and simultaneously remove the tensioning pulley.
– Make sure that the oil return-flow line for exhaust gas turbo‐
charger is not damaged.
– Place the cylinder head so that the oil return-flow line is not
bent. If necessary, put a piece of wood under the exhaust
manifold.

WARNING

Risk of damage to the glow plugs when turning the cylinder

head.
♦ If the cylinder head is removed with installed glow plugs,
do not place it down on the sealing surface since the glow
plugs protrude slightly beyond the sealing surface.

1.5.2 Install

Note

♦ There must not be any oil or coolant present in the blind holes
for the cylinder head bolts.
♦ Replace cylinder head bolts.
♦ Renew self-locking nuts.
♦ Replace screws which have been tightened to torquing angle.
♦ Always replace gasket rings and seals.
♦ Remove the new cylinder head gasket from its wrapping im‐
mediately before fitting. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Treat the seal with the utmost care. Damage to the silicone
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
layer and in the area of the bead results in leakages.
♦ When installing an exchange cylinder head with the camshafts
installed, it is necessary to oil the contact surfaces between
the roller arms and the cams after installing the cylinder head.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .
♦ To ensure that no valve is set during starting, turn the crank‐
shaft carefully by at least 2 turns.

WARNING

Wear protective gloves when working with sealant and grease

remover!

94 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Make sure that when cleaning the cylinder head and cylinder
block no foreign bodies can get into the cylinder or into the oil
and coolant galleries.
– Carefully remove old sealant residue from the cylinder head
and cylinder block using a chemical sealant remover.
– Remove the crankshaft arrester - T10490- before fitting on the
cylinder head and turn back the crankshaft in the opposite di‐
rection of rotation of the engine until all the pistons are almost
evenly at “TDC”.
– If there are no dowel sleeves are available for centering the
cylinder block and cylinder head, insert dowel sleeves.
– Pay attention to the identification of the cylinder head gasket:
♦ Part number = -arrow 1-
♦ Holes -arrow 2- (ignore)
♦ Holes -arrow 3-

Note

♦ If the cylinder head gasket or cylinder head has been replaced,

select the new head cylinder head gasket according to the
number of holes of the old cylinder head gasket.
♦ If parts of the crankshaft drive were replaced, you must rede‐
fine the new cylinder head gasket by measuring the protrusion
of the piston in the “TDC” ⇒ page 78 .

– Place cylinder head gasket on the dowel sleeves -arrows- in

the cylinder block.
• Fitting position of the cylinder head gasket: Identification “top”
or part number for cylinder head

Note

The assistance of a 2nd mechanic is required for fitting on the

cylinder head.

– Insert the cylinder head.

– Insert screws for cylinder head and tighten ⇒ page 88 .

Note

Tightening up the cylinder head bolts after doing repair work is

not necessary.

1. Removing and installing cylinder head 95

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Turn the crankshaft in the direction of rotation of the engine

until the stud -arrow- of the crankshaft arrester engages -
T10490- during this rotary movement in the sealing flange.
– install (set the timing) ⇒ page 52 .
Continued installation is carried out in the reverse order. When
installing, note the following:
– Install exhaust gas cleaning module ⇒ page 360 .
– Install pre-exhaust pipe ⇒ page 349 .
– Install the left coolant pipe ⇒ page 163 .
– Install the rear coolant pipe ⇒ page 164 .
– Install the front top coolant pipe ⇒ page 157 .
– Electrical connections and proper routing ⇒ Electrical System;
Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
– Change engine oil ⇒ Maintenance ; Booklet Octavia III .
– Replace coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - cylinder head
⇒ “1.4 Assembly overview - cylinder head”, page 85
♦ Summary of components - removing and installing parts of the
lubrication system
⇒ “1.1 Summary of components - removing and installing parts
of the lubrication system ”, page 116
♦ Summary of components - exhaust gas turbocharger with
component parts
⇒ “1.1 Exhaust gas turbocharger with component parts - Sum‐
mary of components”, page 265
♦ Assembly overview - intake manifold
⇒ “6.1 Assembly overview - intake manifold”, page 325
♦ Summary of components
Protected - exhaust
by copyright. Copying gas
for private or recirculation
commercial purposes, inwith
part orra‐
in whole, is not permitted
diator for exhaust
unless authorisedgas recirculation
by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
⇒ “4.1 Exhaust gas recirculation with radiator for exhaust gas
recirculation - Summary of components”, page 375

1.6 Checking compression

Special tools and workshop equipment required
♦ Flexible-head wrench SW 10 - 3220-
♦ Compression tester , e.g. -V.A.G 1763-
♦ Adapter - V.A.G 1763/8-
Test prerequisite
• Engine oil temperature approx. 80 C.
• Battery voltage at least 12.5 V
Test procedure
– Remove engine cover at the top ⇒ page 9 .

96 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connection at the fuel pressure con‐

trol valve - N276- -Pos. 2-.

Note

-Do not pay attention to the position 1-.

– To relieve the fuel pressure in the high pressure accumulator,

start engine for a short time.
– Remove all glow plugs ⇒ page 386 .

– Screw in adapter - V.A.G 1763/8- in place of the respective

glow plug and connect compression tester - V.A.G 1763- .

Note

Use of the compression tester - V.A.G 1763- ⇒ Operating in‐

structions .

– The 2nd mechanic operates the starter until the tester no lon‐
ger indicates a pressure rise.
– Repeat the procedure for each cylinder.
Compression readings Pressure
New part 2.5 ... 3.1 MPa (25.0 ... 31.0
bar)
Wear limit 1.9 MPa (19.0 bar)
Maximum difference between 0.5 MPa (5.0 bar)
cylinders
Assembling
Assembling is performed in the reverse order, while paying at‐
tention to the following:
– Install the glow plug for the relevant cylinder ⇒ page 386 .
– Interrogating and erasing fault memory of engine control unit
⇒ Vehicle diagnostic tester.

1. Removing and installing cylinder head 97

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Valve gear

2.1 Assembly overview - valve gear

1 - Valve
❑ do not rework, only
grinding in is permissi‐
ble
❑ mark the fitting position
for re-installation
❑ Valve dimensions
⇒ page 115
❑ inspecting valve guides
⇒ page 115
2 - Cylinder head
❑ the valve seats must not
be reworked because of
the narrow tolerances
3 - Fit pin
❑ for camshaft housing
4 - Valve stem seal
❑ Renew. ⇒ page 109 .
5 - Valve spring
6 - Valve spring plate
7 - Hydraulic balancing ele‐
ment
❑ Checking ⇒ page 108 .
❑ mark the fitting position
for re-installation
❑ oil the contact surfaces
before installing
8 - Valve collets
9 - Roller rocker finger
❑ removing and installing
⇒ “2.5 Removing and in‐
stalling camshaft housing”, page 104
❑ mark the fitting position for re-installation
❑ inspect roller bearings for smooth
Protectedoperation
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ oil the contact surfaces beforewithinstalling
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

10 - Screw cap
❑ replace after removal
❑ removing: In cases where there is a built-in camshaft housing, insert a punch at the side of the cover and
lever out
❑ Installing: Without sealant with a suitable pressure bushing drive in driver - 3390- until flush
11 - Shaft sealing ring
❑ Renew. ⇒ page 100 .
12 - Camshaft housing
❑ with integrated camshaft
❑ removing and installing ⇒ “2.5 Removing and installing camshaft housing”, page 104

98 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

13 - Screw
❑ loosening order ⇒ page 106
❑ Tightening torque and tightening order ⇒ page 100
14 - Sealing ring
❑ replace after removal
15 - Cover
16 - 8 Nm
17 - Fitting sleeve
❑ only for vehicles with engine identification characters CRKB
18 - 8 Nm
❑ only for vehicles with engine identification characters CRKB
19 - Sealing ring
❑ only for vehicles with engine identification characters CRKB
❑ replace after removal
20 - Inlet camshaft control valve 1 - N205-
❑ only for vehicles with engine identification characters CRKB
❑ removing and installing ⇒ page 102
21 - 8 Nm
❑ only for vehicles with engine identification characters CRKB
22 - Bush
❑ for camshaft control
❑ only for vehicles with engine identification characters CRKB
23 - Fitting sleeve
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ onlywith forrespect
vehicles with engine identification characters CRKB
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

24 - Gasket
❑ only for vehicles with engine identification characters CRKB
25 - Setting valve, 50 Nm
❑ only for vehicles with engine identification characters CRKB
26 - Camshaft adjuster
❑ only for vehicles with engine identification characters CRKB
❑ removing and installing ⇒ page 102
27 - O-ring
❑ replace after removal
28 - Hall sender - G40-
❑ Summary of components ⇒ page 385
29 - 9 Nm
30 - Locking clip
❑ for hydraulic balancing element
31 - Fit pin
❑ for camshaft housing

2. Valve gear 99
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Camshaft housing - tightening torque and tightening order

– Tighten screws in steps in the given sequence:
Stage Screws Tightening torque
1. -1 … 18- by hand as far as the stop
• The camshaft housing must rest
on the cylinder head with its com‐
plete contact surface.

2. -1 … 18- 8 Nm

2.2 Replacing camshaft gasket ring

Special tools and workshop equipment required
♦ Extractor - authorised
T10443-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Assembly tool - T10493-
Procedure
– Remove the toothed belt from the camshaft ⇒ page 47 .

WARNING

♦ If it is turned back too much, the inner pressure plate loos‐

ens -T10443- from the pressure screw. The pressure plate
must then be pressed onto the pressure screw once again.

– Carefully turn back set screw -arrow- of the extractor -T10443-

until a slight resistances noticeable.

100 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Place extractor - T10443- straight, as shown in the illustration,

and lock by tightening the set screw -A-.
– Screw in the pressure screw -B- until the gasket ring is pulled
out.
– Clean the contact and sealing surfaces.

Note

The sealing lip of the shaft sealing ring must neither be oiled nor
greased additionally.

– Fit the guide bushing -T10493/1- onto the camshaft, as shown

in the illustration.
– Carefully slide the shaft sealing ring -1- over the guide bushing
onto the camshaft.

Note

The guide bushing remains fitted on the camshaft as a stop while

the oil seal is being pressed in.

– Press in the gasket ring with pressure bushing -T10493/2- and

screw -T10493/3- up to the stop.
– install (set the timing)
Protected ⇒ page
by copyright. 52 .for private or commercial purposes, in part or in whole, is not permitted
Copying
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2. Valve gear 101

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.3 Removing and installing camshaft con‐

trol valve 1 - N205-
Removing
– Remove air filter ⇒ page 334 .
– Separate electrical plug connection -2-.
– Unscrew screw -1-, remove camshaft control valve 1 - N205- .
Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

Renew O-ring.

Tightening torques
♦ Valve gear - Summary of components
⇒ “2.1 Assembly overview - valve gear”, page 98
♦ Summary of components - air filter ⇒ page 332

2.4 Removing and installing camshaft con‐

trol
Special tools and workshop equipment required
♦ Rig pin for the diesel injection pump - 3359-
♦ Rig pin - T10492-
Removing
– Remove top toothed belt guard ⇒ page 43 .
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .

Caution

Risk of destruction as a result of the toothed belt pulley jump‐

ing.
♦ Only rotate the crankshaft in the direction of rotation of the
engine!

– Turn the crankshaft using the screw on the toothed belt gear
until the camshaft sprocket is in the position for “TDC”.

102 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Lock hub of the camshaft using the diesel injection pump rig
pin - 3359- ; to do so, insert the rig pin into fork -2- of the driver
and into the bore behind it -1- in the cylinder head.

– Disconnect the electrical plug connection -2- from the injection

unit for cylinder 1.
– On the cylinder head cover, unlock and remove screw plug
-1- by turning it to the left.

– Lock the inlet camshaft with rig pin - T10492- . Please note the
following when doing so:
The cylinder head cover -1- is installed:
• The distance -a- is approx. 1 mm.

2. Valve gear 103

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

the cylinder head cover is removed:

• The groove -1- on the rig pin - T10492- must match the cam‐
shaft housing -2-.
– Remove air filter ⇒ page 334 .

– Separate electrical plug connections -3- and -4-. Remove the

clip from the housing.
– Release screws -2-, remove housing -1-.

Caution

Before removing the actuation valve, check the small pistons

in the middle of the valve for freedom of movement. Press a
finger on the piston and check whether it can be pressed in
before moving into the end position. Replace the actuation
valve if Protected
the piston jams.Copying
by copyright. Otherwise
for privatedamage topurposes,
or commercial the engine
in part ormay
in whole, is not permitted
arise. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unscrew actuation valve -2-, remove camshaft control -1-.

Install
Installation is performed in the reverse order, pay attention to the
following points:
– Install top toothed belt guard ⇒ page 43 .
Tightening torques
♦ Valve gear - Summary of components
⇒ “2.1 Assembly overview - valve gear”, page 98
♦ Sound dampening system - Summary of components ⇒ Body
Work; Rep. gr. 50 .

2.5 Removing and installing camshaft hous‐

ing
Special tools and workshop equipment required
♦ Silicone sealant ⇒ ETKA - Electronic Catalogue of Original
Parts
♦ Sealant remover gasket stripper (bearing code GST, bearing
article no. R 34402), manufacturer Retech s.r.o.
♦ Cleaning and degreasing agent , e.g. -D 009 401 04-
♦ Protective goggles and gloves

104 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing
• Cylinder head fitted.
– Remove the toothed belt from the camshaft ⇒ page 47 .
– Remove cylinder head cover ⇒ page 82 .
– Remove fuel distributor ⇒ page 307 .
– Remove left coolant pipe ⇒ page 163 .
– Release screws -arrows-, push the right charge air pipe slight‐
ly to the side.
– Disconnect the plug connection -2- for hall sender - G40- .

Note

-Do not pay attention to the position 1-.

For vehicles with engine identification characters CRKB

– Separate electrical plug connection -2-.

Continued for all vehicles

– Unscrew screw -1-, loosen screw -2-.

2. Valve gear 105

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen screw -1- and remove clamping sleeve.

– Loosen screws -2-, unscrew screws -arrows-.
– Push exhaust gas cleaning module back slightly.

– Loosen screws for camshaft housing in the sequence

-18 … 1-.
– Unscrew the screws and carefully loosen the camshaft hous‐
ing and remove from the bonding.
Install
Requirements:

• Interlock crankshaft with crankshaft arrester - T10490- .

106 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

• Lock the hub of the camshaft with the rig pin for diesel injection
pump - 3359- .
• Screw loosely inserted.

Caution

Risk of contamination of the lubrication system and bearing.

Cover opened engine parts.

WARNING

Wear protective gloves when working with sealant and grease

remover!

– Remove residual sealant on the bearing frame and cylinder

head using a chemical sealant remover.
– Clean sealing surfaces, they must be free of oil and grease.

Note

Pay attention to the use by date on sealant.

– Cut off nozzle on tube at front marking (∅ of nozzle approx.

1.5 mm).

Caution

Risk of contamination of the camshaft bearings through excess

sealant.
♦ Do not apply thicker sealant beads than indicated.

2. Valve gear 107

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Apply sealant beads -arrow- onto the clean sealing surfaces

of the cylinder head as shown in the illustration.
• Thickness of sealant bead: 2 mm.

Note

♦ After applying the sealant, install the camshaft housing within

5 minutes.
♦ After installing the camshaft housing, allow the sealant to dry
for about 30 minutes.

– Carefully place the camshaft housing on the cylinder head,

pay attention to fit pins when doing so.
– Tighten camshaft housing screws ⇒ page 100 .
Continued installation is carried out in the reverse order. When
installing, note the following:
– Install exhaust gas cleaning module ⇒ page 360 .
– Install camshaft sealing ring ⇒ page 100 by
Protected . copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Install cylinder head cover ⇒ page 82 .
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– install (set the timing) ⇒ page 52 .

Caution

Risk of damaging valves and piston crowns after work on the

valve gear.
♦ Because hydraulic compensation elements must be set,
the engine must not be started until approximately 30 mi‐
nutes after camshaft installation.
♦ To ensure that no valve is set during starting, turn the
crankshaft carefully by at least 2 turns.

Tightening torques
♦ Camshaft housing - tightening torque and tightening order
⇒ Fig. ““Camshaft housing - tightening torque and tightening
order”“ , page 100
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - fuel distributor
⇒ “2.2 Fuel distributor - summary of components”, page 297

2.6 Checking hydraulic balancing elements

Note

♦ The hydraulic balancing elements cannot be repaired.

♦ Irregular valve noises when starting engine are normal.

Special tools and workshop equipment required

♦ Feeler gauges

108 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Test procedure
– Start engine and allow to run until the radiator fan has cut in
once.
– Increase engine speed to about 2500 rpm for 2 minutes and
conduct a test drive if necessary.

Note

If the irregular valve noises disappear but occurs regularly during

short journeys, the oil backstop must be replaced. Installation lo‐
cation of oil backstop in the oil filter housing -Pos. 9 -
⇒ page 119 .

– If the hydraulic balancing elements are still loud, determine

which is the faulty balancing element as follows:
– Remove cylinder head cover ⇒ page 82 .
– Rotate crankshaft on the toothed belt pulley screw until the
cam of the compensating element being checked is positioned
at the top.
– To determine the clearance between cam and roller rocker
finger, press the roller rocker finger down - Arrow - .
– If a feeler gauge can be moved by 0.20 mm between the cam
and the roller rocker finger, change the hydraulic compensat‐
ing element
⇒ “2.5 Removing and installing camshaft housing”,
page 104 .
Concluding measures
– Install cylinder head cover ⇒ page 82 .

2.7 Removing and installing valve stem

seals

2.7.1 Removing and installing valve stem

seals with cylinder head installed
Special tools and workshop equipment required
♦ Valve stem seal extractor - MP 1-230 (3364)-
♦ Valve stem seal fitting tool - MP 1-233 (3365)-
♦ Disassembly and assembly device for valve collets - VAS
5161- with sealing bolts -VAS 5161/29-2- , guide plate -VAS
5161 A/31- and sleeve -VAS 5161 A/31-1-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Procedure unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove all glow plugs ⇒ page 386 .

– Remove the camshaft housing ⇒ page 104 .
– When installing again, mark the assignment of the roller rocker
arms and the hydraulic clearance compensation elements.
– Remove the roller rocker arms together with the hydraulic bal‐
ancing elements and lay aside on a clean surface.
– Put the piston of the relevant cylinder at “bottom dead centre”.

2. Valve gear 109

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Cylinders 1, 3, 4:
– Position the guide plate -VAS 5161 A/31- onto the cylinder
head.
• Labelling -A- points to the exhaust gas turbocharger side
• Labelling - E - points to intake manifold side
– Tighten guide plate with knurled screws -VAS 5161/12- by
hand.
• Position of the knurled screws, as shown in the illustration
Cylinder 2:

– Position the guide plate -VAS 5161 A/31- onto the cylinder
head.
• Labelling -A- points to the exhaust gas turbocharger side
• Labelling - E - points to intake manifold side
– Tighten guide plate with knurled screws -VAS 5161/12- by
hand.
• Position of the knurled screws, as shown in the illustration
Continued for all cylinders:

– Screw the sealing bolt -VAS 5161/29-2- into the guide plate.
– Screw the adapter -VAS 5161/11- into the relevant pencil type
glow plug thread by hand.

– Insert the impact drift -VAS 5161/3A- into the guide plate and
knock off the tightly fitted valve collets using a plastic hammer.

110 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Screw the detent part -VAS 5161/6- with the interlocking fork
-VAS 5161/5- into the guide plate.
– Insert assembly cartridge -VAS 5161/8- with sleeve mounted
-VAS 5161 A/31-1- into the guide plate.
– Connect the adapter to the compressed air with a commer‐
cially available intermediate piece and apply constant pres‐
sure.
• Minimum pressure: 0.6 MPa (6 bar) overpressure.
– Hook the pressure fork -VAS 5161/2- onto the detent part and
push the assembly cartridge downwards.
– Turn simultaneously the knurled screw of the assembly car‐
tridge to the right, until the tips click into the valve collets.
– Rotate the knurled screw to the left and to the right, by doing
so the valve collets are pressed apart and are installed in the
assembly cartridge.
– Release the pressure fork.
– Remove assembly cartridge with sleeve.
– Remove the valve spring with the valve spring retainer.

– Pull off valve stem seal with extractor for valve stem seal -
3364- .

WARNING

Risk of damage when installing the valve stem seals.

♦ Fit the plastic bushing -A-, which is attached to the new
valve stem seals -B-, onto the valve stem.

– Lightly oil sealing lip of the valve stem seal.

– Slide the valve stem seal onto the plastic bushing.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Carefully press the
unlessvalve stem
authorised seal AUTO
by ŠKODA with A.the valveAUTO
S. ŠKODA stem seal
A. S. does not guarantee or accept any liability
insertion tool - 3365- onto tothe
with respect the valve guide.
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove plastic sleeve.

If the valve collets were removed from the assembly cartridge,

first of all they must be inserted into the insertion device for valve
collets -VAS 5161/18- .
• The large diameter of the valve collets points to the top.
– Insert the valve spring and the valve spring retainer.
– Press the assembly cartridge from the top onto the insertion
device for valve collets and lift up the valve collets.

2. Valve gear 111

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Re-insert the assembly cartridge into the guide plate -VAS

2.7.2 Removing and installing valve stem

seals with cylinder head removed
Special tools and workshop equipment required
♦ Valve stem seal extractor - MP 1-230 (3364)-
♦ Valve stem seal fitting tool - MP 1-233 (3365)-
♦ Disassembly and assembly device for valve collets - VAS
5161- with guide plate -VAS 5161 A/31- and sleeve -VAS 5161
A/31-1-
♦ Engine and gearbox support - VAS 6095-
♦ Cylinder head tensioning device - VAS 6419-
Procedure
– Remove the camshaft housing ⇒ page 104 .
– When installing again, mark the assignment of the roller rocker
arms and the hydraulic clearance compensation elements.
– Remove the roller rocker arms together with the hydraulic bal‐
ancing elements and lay aside
Protected on aCopying
by copyright. cleanfor surface.
private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Insert the cylinder head
with tensioning device of- VAS
respect to the correctness 6419-
information in thisinto the Copyright by ŠKODA AUTO A. S.�
document.
engine and gearbox jack - VAS 6095- .
– Tension the cylinder head in the cylinder head tensioning de‐
vice, as shown in the illustration.
– Connect cylinder head tensioning device to compressed air.
– Adjust the air bellows with the lever -arrow- below the com‐
bustion chamber on which the valve stem seals should be
removed.
– Allow just enough air to flow into the air bag so that it applied
to the valve disc.
Cylinders 1, 3, 4:

112 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Position the guide plate -VAS 5161 A/31- onto the cylinder
head.
• Labelling -A- points to the turbocharger side
• Labelling - E - points to intake manifold side
– Tighten guide plate with knurled screws -VAS 5161/12- by
hand.
• Position of the knurled screws, as shown in the illustration
Cylinder 2:

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Continued for all cylinders: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Insert the impact drift -VAS 5161/3A- into the guide plate and
knock off the tightly fitted valve collets using a plastic hammer.

– Screw the detent part -VAS 5161/6- with the interlocking fork
-VAS 5161/5- into the guide plate.
– Insert assembly cartridge -VAS 5161/8- with sleeve mounted
-VAS 5161 A/31-1- into the guide plate.
– Hook the pressure fork -VAS 5161/2- onto the detent part and
push the assembly cartridge downwards.
– Turn simultaneously the knurled screw of the assembly car‐
tridge to the right, until the tips click into the valve collets.
– Rotate the knurled screw to the left and to the right, by doing
so the valve collets are pressed apart and are installed in the
assembly cartridge.
– Release the pressure fork.
– Remove assembly cartridge with sleeve.
– Remove the valve spring with the valve spring retainer.

2. Valve gear 113

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Pull off valve stem seal with extractor for valve stem seal -
3364- .

WARNING

Risk of damage when installing the valve stem seals.

♦ Fit the plastic bushing -A-, which is attached to the new
valve stem seals -B-, onto the valve stem.

– Lightly oil sealing lip of the valve stem seal.

– Slide the valve stem seal onto the plastic bushing.
– Carefully press the valve stem seal with the valve stem seal
insertion tool - 3365- onto the valve guide.
– Remove plastic sleeve.

If the valve collets were removed from the assembly cartridge,

first of all they must be inserted into the insertion device for valve
collets -VAS 5161/18- .
• The large diameter of the valve collets points to the top.
– Press the assembly cartridge from the top onto the insertion
device for valve collets and lift up the valve collets.
– Insert the valve spring and the valve spring retainer.

– Re-insert the assembly cartridge into the guide plate -VAS

5161 A/31- .
– Press down the pressure fork and turn the knurled screw to
the left and to the right while pulling it upwards, by doing so
the valve collets are inserted.
– Release the pressure fork on tightened knurled screw.
– Repeat the procedure for each valve.
Assembling
Assembling is performed in the reverse order, while paying at‐
tention to the following:
– Ensure that all the roller arms are correctly positioned on the
valve stem ends and are clipped in place on the relevant hy‐
draulic balancing elements.
– Install camshaft housing ⇒ page 104 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

114 Rep. gr.15 - Cylinder head, valve gear

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.8 Valve dimensions

Note

Inlet and exhaust valves must not be reworked. Only lapping-in

is permitted.

Dimension Inlet valve Exhaust valve

∅a mm 28.10 26.00
∅b mm 5.975 5.965
c mm 99.30 99.10
α ∠° 45 45

2.9 Checking valve guides

Special tools and workshop equipment required
♦ Universal dial gauge bracket - MP 3-447 (VW 387)-
♦ Dial gauge
Test procedure

Note
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ If theunless
valve is to bybeŠKODA
authorised renewed
AUTO A.as part of
S. ŠKODA a repair,
AUTO A. S. doesuse a new or accept any liability
not guarantee
valve with
for respect
the measurement.
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Because of the different shank diameters you must use only

one intake valve in the intake valve guide and one exhaust
valve in the exhaust valve guide.

– Secure dial gauge to the cylinder head using the universal dial
gauge bracket - MP 3-447 (VW 387)- .

Note

If the valves are replaced when carrying out repair work, use new
valves for the measurement.

– Insert valve into valve guide. The end of the valve stem must
be flush with the guide.
• Valve rock: max. 1.0 mm

Note

If the wear limit is exceeded, repeat measurement with new

valves. If the wear limit is again exceeded, replace cylinder head.
The valve guides cannot be replaced.

2. Valve gear 115

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

17 – Lubrication
1 Removing and installing parts of the
lubrication system

Note

♦ If considerable quantities of metal swarf as well as abrasion is

found in the engine oil when carrying out engine repairs, care‐
fully clean the oil galleries in order to avoid consequential
damage and additionally replace the oil injection nozzles and
the engine oil cooler as well as the oil filter element.
♦ The oil level must not be above the max. marking - risk of
damage to catalytic converter!

Check the engine oil, amount of oil and oil specification:

♦ ⇒ Maintenance ; Booklet Octavia III .

1.1 Summary of components - removing and installing parts of the lubrication

system

1 - 8 Nm
❑ self-locking
❑ replace after removal
2 - Oil level and oil temperature
sender - G266-
❑ removing and installing
⇒ page 118
3 - Sealing ring
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ replace after removal
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
4 - Oil drain plug, 30 Nm
❑ with integrated gasket
ring
❑ replace
5 - Sealing ring
❑ Component part of the
drain plug
6 - Bolt
❑ Tightening torque and
tightening order
⇒ page 118
7 - Oil sump
❑ removing and installing
⇒ page 123
8 - O-ring
❑ replace after removal
9 - 10 Nm + torque a further
180° (1/2 turn)
❑ replace after removal

116 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 - Oil pump
❑ with vacuum pump
❑ removing and installing ⇒ page 126
11 - Fitting sleeve
12 - Toothed belt
❑ removing:
– Remove oil pump ⇒ page 126

– Remove sealing flange on the belt pulley side ⇒ page 60

Caution
Do not kink or twist the
toothed belt or damage it
with sharp edges.

13 - Seal
❑ replace after removal
14 - Fitting sleeve
15 - Cylinder block
16 - O-ring
❑ replace after removal
17 - Oil pressure control valve - N428-
❑ removing and installing ⇒ page 129
18 - 8 Nm
19 - 8 Nm
20 - Guide tube for oil dipstick
21 - 8 Nm
22 - O-ring
❑ replace after removal
23 - 8 Nm + torque a further 90° (1/4 turn)
24 - Baffle
25 - Oil suction pipe

1. Removing and installing parts of the lubrication system 117

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Oil sump - tightening torque and tightening order

– Tighten screws in steps as follows:
Stage Screws Tightening torque
1. -1 … 18- crosswise 5 Nm
2. -Arrows- 40 Nm
3. -1 … 18- crosswise in steps up to 13 Nm

1.2 Removing and installing oil level and oil

temperature sender - G266-
Removing
• Engine oil drained ⇒ Maintenance ; Booklet Octavia III .
– Disconnect electrical plug connection -arrow- at the oil level
and temperature sender - G266- .

– Loosen clips -arrows-, remove noise insulation -1- for oil sump.

118 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -1- and remove oil level and oil temperature
sender - G266- -Pos. 4-.

Note

-Do not pay attention to the position 3-.

Install
Installation is performed in the reverse order, while paying atten‐
tion to the following:

Note

Replace the sealing ring-2- and the self-locking screws -1-.

– Fill with engine oil and check the oil level ⇒ Maintenance ;
Booklet Octavia III .
Tightening torques
♦ Summary of components - removing and installing parts of the
lubrication system
⇒ “1.1 Summary of components - removing and installing parts
of the lubrication system ”, page 116

1.3 Summary of components - oil filter holder

1. Removing and installing parts of the lubrication system 119

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Oil drain plug, 5 Nm

2 - O-ring
❑ replace after removal
3 - Screw cap, 25 Nm
4 - O-ring
❑ replace after removal
❑ wet with engine oil
5 - Oil filter element
❑ pay attention to note
⇒ page 116
❑ removing and installing
⇒ Maintenance ; Book‐
let Octavia III
6 - Sealing ring
❑ captive, replace if the oil
pressure switch has
leaks
7 - Oil pressure switch - F1- ,
20 Nm
❑ Switching pressure
0.25 ... 0.32 MPa (2.5 ...
3.2 bar)
❑ Isolation brown
❑ Checking ⇒ Vehicle di‐
agnostic tester.
❑ removing and installing
⇒ page 127
8 - Screw
❑ replace after removal Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Tightening torque and with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
tightening order
⇒ page 121
9 - Oil filter housing with engine oil cooler
❑ Oil filter housing and engine oil cooler must not be disconnected
❑ removing and installing ⇒ page 121
10 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 121
11 - Gasket
❑ replace after removal
12 - Sealing ring
❑ replace after removal
13 - Oil pressure switch for reduced oil pressure - F378- , 20 Nm
❑ Switching pressure 0.03 ... 0.06 MPa (0.3 ... 0.6 bar)
❑ Insulation green
❑ Checking ⇒ Vehicle diagnostic tester.
❑ removing and installing ⇒ page 128
14 - Sealing ring
❑ captive, replace if the oil pressure switch has leaks

120 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Oil filter housing - tightening torque and tightening order

Note

Replace screws which have been tightened firmly to a torquing

angle.

– Attach the top left and bottom right screws first.

– Tighten screws in steps in the given sequence:
Stage Screws Tightening torque/torquing angle
1. -1 … 5- 20 Nm
2. -1 … 5- Turn 90° further

1.4 Removing and installing the oil filter

holder with the engine oil cooler
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-

Note

The engine oil cooler must not be disconnected from the oil filter
housing In the event of a defect, the engine oil cooler must be
replaced by the oil filter holder ⇒ page 121 .

Removing
– Remove air filter ⇒ page 334 .
– Remove fan shroud for radiator fan ⇒ page 177 .
– Remove the front left coolant pipe ⇒ page 160 .
– Remove the front right coolant pipe ⇒ page 162 .
– Release vacuum hoses -arrows-. Remove coolant hose.

Note

-Do not pay attention to the position 1-.

1. Removing and installing parts of the lubrication system 121

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -2-.

– Unscrew screws -1- and push pump for charge air cooler -
V188- -Pos. 3- to the side.

– Disconnect electrical plug connection -1- at the - N428- oil

pressure control.

Note

-Do not pay attention to the position 2-.

– Disconnect electrical plug connection -arrow- at the oil pres‐

sure switch for reduced oil pressure - F378- .

122 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

Place a cloth underneath to absorb escaping engine oil.

– Unscrew screws in the order -5 ... 1-,remove oil filter housing

together with the engine oil cooler.
Install
Installation is performed in the reverse order, while paying atten‐
tion to the following:

Note

♦ Replace gasket and O-ring.

♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

– Install front right coolant pipe ⇒ page 162 .

– Install front left coolant pipe ⇒ page 160 .
– Install fan shroud for radiator fan ⇒ page 177 .
– Connect coolant hose with quick coupling ⇒ page 172 .
– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - oil filter holder
⇒ “1.3 Summary of components - oil filter holder”, page 119
♦ Summary of components - electric coolant pump
⇒ “2.3 Summary of components - electric coolant pump”, page
149
♦ Summary of components - air filter ⇒ page 332

1.5 Removing and installing oil sump

Special tools and workshop equipment required
♦ Flexible-head wrench SW 10 - 3185-
♦ Allen key, long reach - T10058-
♦ Silicone sealant ⇒ ETKA - Electronic Catalogue of Original
Parts
♦ Sealant remover gasket stripper (bearing code GST, bearing
article no. R 34402), manufacturer Retech s.r.o.
♦ Cleaning and degreasing agent , e.g. -D 009 401 04-
♦ Protective goggles and gloves
Removing
• Engine oil drained ⇒ Maintenance ; Booklet Octavia III .

1. Removing and installing parts of the lubrication system 123

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connection -arrow- at the oil level

and temperature sender - G266- .

– Loosen clips -arrows-, remove noise insulation -1- for oil sump.

– Screw out screws -arrows- of oil pan/gearbox.

– Loosen bolts -1 … 18- crosswise and release.
– Loosing oil sump carefully from the bonding.

Note

A vehicle with manual gearbox 02Q is shown as an example.

Install
Installation is carried out in the reverse order. When installing,
note the following:
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Caution with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Risk of contamination of the lubrication system and bearing.

Cover opened engine parts.

WARNING

Wear protective gloves when working with sealant and grease

remover!

– Remove residual sealant from the sealing surfaces on the cyl‐

inder block and on the oil pan with chemical sealant remover.
– Degrease the sealing surfaces.

124 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

Pay attention to the use by date on sealant.

– Cut off nozzle tube at the front marking (∅ of nozzle approx.

2 ... 3 mm).

Caution

There is risk of blockage of the lubrication system through ex‐

cess sealant.
Do not apply thicker sealant strips than indicated.

When the sealing flange on the belt pulley side was not replaced

Note

The bottom surface of the sealing flange on the belt pulley side
has a displacement of approx. 1 mm to the bottom cylinder block
surface after removing the old silicone seal, which must be com‐
pensated for by applying the required sealant on the correspond‐
ing area of the oil pan sealing surface.

– Apply sealant bead onto the clean sealing surfaces of the oil
sump, as shown in the illustration.
♦ In the area of the sealing surface of the sealing flange on the
belt pulley side -between arrows-: 3 … 4 mm
♦ In the area of the sealing surfaces of the cylinder block and
the sealing flange on the gearbox side: 2 … 3 mm
• The sealant strips must be replaced in the area of the sealing
flange on the belt pulley side with the sealant bead equal to
the height and width of the silicone seal.

Note

After applying the sealant, you must install the oil sump within 5
minutes.

When the sealing flange on the belt pulley side was not replaced

1. Removing and installing parts of the lubrication system 125

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Apply sealant bead onto the clean sealing surfaces of the oil
sump, as shown in the illustration.
♦ Thickness of sealant bead: 2 … 3 mm

Note

♦ Take particular care when applying sealant bead in the area

of the sealing flange.
♦ After applying the sealant, you must install the oil sump within
5 minutes.

Continue as follows for both procedures

– Insert baffle.
– Position oil sump and tighten screws ⇒ page 118 .
• The oil pan must be flush to the gearbox flange at the inter‐
mediate plate.

Note

♦ When installing the oil pan with the engine removed you must
ensure that the oil sump is flush with the cylinder block at the
flywheel side.
♦ After installing the oil sump, the sealant must dry for approxi‐
mately 30 minutes. Only then fill with engine oil.

– Fill with engine oil and check the oil level ⇒ Maintenance ;
Booklet Octavia III .
Tightening torques
♦ Oil sump - tightening torque and tightening order
⇒ Fig. ““Oil sump - tightening torque and tightening order”“ ,
page 118

1.6 Removing and installing

Protectedoil pumpCopying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Removing
– Remove sump ⇒ page 123 .

Caution

Do not kink or twist the toothed belt or damage it with sharp

edges.

126 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -arrows- and remove oil pump -1-.

Caution

The screw at the pump wheel must not be released.

Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace gasket.
♦ Replace screws which have been tightened firmly to a torquing
angle.

– If no dowel sleeves -arrows- are present in the oil pump, insert

dowel sleeves.
– Install sump ⇒ page 123 .
Tightening torques
♦ Summary of components - removing and installing parts of the
lubrication system
⇒ “1.1 Summary of components - removing and installing parts
of the lubrication system ”, page 116

1.7 Removing and installing oil pressure

switch - F1-
Removing
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– authorised
unless Remove engine
by ŠKODA AUTOcover at the
A. S. ŠKODA topA.⇒S. page
AUTO does not9guarantee
. or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Release screws -1, 3-.
– Unlock catch -arrows-, remove cover-2-.

1. Removing and installing parts of the lubrication system 127

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove top part-1- of air guide.

– Release screw left and right -arrow-.

– Unclip and remove bottom part -1- of air guide.

– Disconnect plug connection -arrow-.

Note

Place a cloth underneath to absorb escaping engine oil.

– Screw out oil pressure switch - F1- .

Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

Replace gasket ring.

– Checking the oil level ⇒ Maintenance ; Booklet Octavia III .

Tightening torques
♦ Summary of components - oil filter holder
⇒ “1.3 Summary of components - oil filter holder”, page 119
♦ Summary of components - air filter ⇒ page 332

1.8 Removing and installing oil pressure

switch for reduced oil pressure - F378-
Removing
– Remove air filter ⇒ page 334 .

128 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect plug connection -arrow-.

Note

Place a cloth underneath to absorb escaping engine oil.

– Unscrew oil pressure switch for reduced oil pressure - F378- .

Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

Replace gasket ring.

– Checking the oil level ⇒ Maintenance ; Booklet Octavia III .

Tightening torques
♦ Summary of components - oil filter holder
⇒ “1.3 Summary of components - oil filter holder”, page 119
♦ Summary of components - air filter ⇒ page 332

1.9 Removing and installing valve for oil

pressure control - N428-
Removing
– Remove V-ribbed belt ⇒ page 36 .
– Remove AC compressor with connected refrigerant hoses
from the holder ⇒ Heating, Air Conditioning; Rep. gr. 87 and
strap up to the right side.

1. Removing and installing parts of the lubrication system 129

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -1-.

Note

Place a cloth underneath to absorb escaping engine oil.

– Unscrew screws -2- and remove oil pressure control valve -

N428- .
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Renew O-ring.

– Install poly V-belt ⇒ page 36 .

– Checking the oil level ⇒ Maintenance ; Booklet Octavia III .
Tightening torques
♦ Summary of components - removing and installing parts of the
lubrication system
⇒ “1.1 Summary of components - removing and installing parts
of the lubrication system ”, page 116
♦ Removing and installing AC compressor ⇒ Heating, Air Con‐
ditioning; Rep. gr. 87 .

1.10 Testing oil pressure

Special tools and workshop equipment required
♦ Oil pressure tester , e.g. -V.A.G 1342-
Procedure
• Oil level o.k.
• Engine oil temperature approx. 80 C.
– Remove oil pressure switch - F1- ⇒ page 127 .
– Connect oil testing device - V.A.G 1342- to the bore for oil
pressure switch - F1- .
– Screw an old oil pressure switch into the oil pressure tester -
V.A.G 1342- bore to close it.
– Start the engine.
• Oil pressure in idle: at least 0.18 MPa (1.8 by
Protected bar)
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
• Oil pressure at 3000 rpm: at least 0.38withMPa (3.8 bar)
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

130 Rep. gr.17 - Lubrication

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

19 – Cooling
1 Cooling system

1.1 Coolant hose schematic diagram

For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC
Vehicles without auxiliary heating system

Note

♦ Blue = large coolant circuit.

♦ Red = small coolant circuit.
♦ Lilac = coolant circuit for charge air cooler.
♦ Brown = heating circuit.
♦ The arrows point in the coolant flow direction.

1 - Cooler for charge air circuit

❑ fill with fresh coolant af‐
ter replacing
2 - Charge air cooler
❑ fill with fresh coolant af‐
ter replacing
3 - Non-return valve
4 - Coolant pump
5 - Cylinder head and cylinder
block
❑ fill with fresh coolant af‐
ter replacing
6 - Coolant expansion tank
7 - Screw cap
❑ for coolant expansion
tank Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ Check pressure reliefby ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
unless authorised
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
valve ⇒ page 145
8 - Heating backup pump -
V488-
9 - Heat exchanger of heating
system
❑ fill with fresh coolant af‐
ter replacing
10 - Radiator for exhaust gas
recirculation
❑ fill with fresh coolant af‐
ter replacing

1. Cooling system 131

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

11 - Coolant temperature sender - G62-

12 - Choke
❑ integrated into the coolant hose, not visible from the outside
❑ The fitting position is not defined, therefore the coolant hose must not be unclipped with the hose clamp
(Risk of damage!)
13 - Coolant connection
14 - Gearbox oil cooler
❑ Equipment variants
15 - Coolant regulator
16 - Engine oil cooler
17 - Coolant radiator
❑ fill with fresh coolant after replacing
18 - Throttle valve module - J338-
19 - Charge air cooler pump - V188-

Vehicles fitted with auxiliary heating

Note

♦ Blue = large coolant circuit.

♦ Red = small coolant circuit.
♦ Lilac = coolant circuit for charge air cooler.
♦ Brown = heating circuit.
♦ The arrows point in the coolant flow direction.

132 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Cooler for charge air circuit

❑ fill with fresh coolant af‐
ter replacing
2 - Charge air cooler
❑ fill with fresh coolant af‐
ter replacing
3 - Non-return valve
4 - Coolant pump
5 - Cylinder head and cylinder
block
❑ fill with fresh coolant af‐
ter replacing
6 - Auxiliary heating
❑ Equipment variants
7 - Coolant expansion tank
8 - Screw cap
❑ for coolant expansion
tank
❑ Check pressure relief
valve ⇒ page 145
9 - Heating backup pump -
V488-
❑ According to build ver‐
sion
10 - Heat exchanger of heating
system
❑ fill with fresh coolant af‐
ter replacing
11 - Radiator for exhaust gas
recirculation
❑ fill with fresh coolant af‐
ter replacing
12 - Coolant temperature sender - G62-
13 - Choke
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ integrated into the coolant hose, bynot
unless authorised visible
ŠKODA AUTOfrom the outside
A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ The fitting position is not defined, therefore the coolant hose must not be unclipped with the hose clamp
(Risk of damage!)
14 - Coolant connection
15 - Gearbox oil cooler
❑ Equipment variants
16 - Coolant regulator
17 - Engine oil cooler
18 - Coolant radiator
❑ fill with fresh coolant after replacing
19 - Throttle valve module - J338-
20 - Charge air cooler pump - V188-

1. Cooling system 133

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.2 Coolant hose schematic diagram

For vehicles with engine identification characters CUPA

Note

♦ Blue = large coolant circuit.

♦ Red = small coolant circuit.
♦ Lilac = coolant circuit for charge air cooler.
♦ Brown = heating circuit.
♦ The arrows point in the coolant flow direction.

Vehicles without auxiliary heating

1 - Cooler for charge air circuit

❑ fill with fresh coolant af‐
ter replacing
2 - Charge air cooler
❑ fill with fresh coolant af‐
ter replacing
3 - Non-return valve
4 - Coolant pump
5 - Cylinder head and cylinder
block
❑ fill with fresh coolant af‐
ter replacing
6 - Coolant expansion tank
7 - Screw cap
❑ for coolant expansion
tank
❑ Check pressure relief
valve ⇒ page 145
8 - Heating backup pump -
V488-
9 - Heat exchanger of heating
system
❑ fill with fresh coolant af‐
ter replacing
10 - Radiator for exhaust gas
recirculation
❑ fill with fresh coolant af‐
ter replacing
11 - Coolant temperature
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
sender - G62-
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
12 - Choke
❑ integrated into the coolant hose, not visible from the outside
❑ The fitting position is not defined, therefore the coolant hose must not be unclipped with the hose clamp
(Risk of damage!)
13 - Coolant connection
14 - Gearbox oil cooler
❑ Equipment variants

134 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

15 - Coolant regulator
16 - Engine oil cooler
17 - Coolant radiator
❑ fill with fresh coolant after replacing
18 - Throttle valve module - J338-
19 - Charge air cooler pump - V188-

Vehicles fitted with auxiliary heating

1 - Cooler for charge air circuit

1. Cooling system 135

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

16 - Coolant regulator
17 - Engine oil cooler
18 - Coolant radiator
❑ fill with fresh coolant after replacing
19 - Throttle valve module - J338-
20 - Charge air cooler pump - V188-

1.3 Coolant hose schematic diagram

For vehicles with engine identification characters CRKB, CRVC

Note

♦ Blue = large coolant circuit.

♦ Red = small coolant circuit.
♦ Lilac = coolant circuit for charge air cooler.
♦ Brown = heating circuit.
♦ The arrows point in the coolant flow direction.

Vehicles without auxiliary heating system

136 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Cooler for charge air circuit

❑ integrated into the coolant hose, not visible from the outside
❑ The fitting position is not defined, therefore the coolant hose must not be unclipped with the hose clamp
(Risk of damage!)
13 - Coolant connection
14 - Gearbox oil cooler
❑ Equipment variants
15 - Coolant regulator
16 - Engine oil cooler
17 - Coolant radiator
❑ fill with fresh coolant after replacing
18 - Throttle valve module - J338-
19 - EGR control motor - V338-
20 - Charge air cooler pump - V188-

Vehicles fitted with auxiliary heating

1. Cooling system 137

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Cooler for charge air circuit

❑ fill with fresh coolant af‐
ter replacing
2 - Charge air cooler
❑ fill with fresh coolant af‐
ter replacing
3 - Non-return valve
4 - Coolant pump
5 - Cylinder head and cylinder
block
❑ fill with fresh coolant af‐
ter replacing
6 - Auxiliary heating
❑ Equipment variants
7 - Coolant expansion tank
8 - Screw cap
❑ for coolant expansion
tank
❑ Check pressure relief
valve ⇒ page 145
9 - Heating backup pump -
V488-
❑ According to build ver‐
sion
10 - Heat exchanger of heating
system
❑ fill with fresh coolant af‐
ter replacing
11 - Radiator for exhaust gas
recirculation
❑ fill with fresh coolant af‐
ter replacing
12 - Coolant temperature sender - G62-
13 - Choke
❑ integrated into the coolant hose, not visible from the outside
❑ The fitting position is not defined, therefore the coolant hose must not be unclipped with the hose clamp
(Risk of damage!)
14 - Coolant connection
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
15 - Gearbox oil cooler
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ Equipment variants
16 - Coolant regulator
17 - Engine oil cooler
18 - Coolant radiator
❑ fill with fresh coolant after replacing
19 - Throttle valve module - J338-
20 - EGR control motor - V338-
21 - Charge air cooler pump - V188-

138 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.4 Draining and filling coolant

Special tools and workshop equipment required
♦ Adapter for cooling system tester - V.A.G 1274/8-
♦ Cooling system charge unit - VAS 6096-
♦ Catch pan , e.g. -VAS 6208-
♦ Hose clip pliers - VAS 6362-
♦ Refractometer
♦ Protective goggles
♦ Protective gloves
Draining

WARNING

Hot steam or hot coolant may escape when the compensation

bottle is opened. Cover the cap with a cloth and open carefully.

– Open cap -arrow- for coolant expansion tank.

– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .
– Place a catch pan - VAS 6208- under the radiator.
Vehicles with radiator version 1

– Raise holding clamp -arrow-, remove bottom left coolant hose

from radiator, allow coolant to drain.

– Raise holding clamp -arrow-, remove bottom right coolant

hose from radiator, allow coolant to drain.
Vehicles with radiator version 2

1. Cooling system 139

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Raise holding clamp -1-, remove bottom right coolant hose

from radiator, allow coolant to drain.
– Raise holding clamp -2-, remove bottom right coolant hose
from radiator, allow coolant to drain.
Vehicles with radiator version 3

– Raise holding clamp -arrow-, remove bottom left coolant hose

from radiator, allow coolant to drain.

– Raise holding clamps -1, 2-, remove coolant hoses from

charge air circuit cooler, allow coolant to drain.
Continued for all vehicles

– Loosen hose clamp -arrow-, remove bottom coolant hose to

heating backup pump - V488- , allow coolant to drain.
Filling up
Procedure
Vehicles with radiator version 1

140 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect coolant hose with quick coupling -arrow- to radiator

bottom left ⇒ page 172 .

– Connect coolant hose with quick coupling -arrow- to charge

air circuit cooler bottom right ⇒ page 172 .
Vehicles with radiator version 2

– Connect coolant hose with quick coupling -1- to radiator bot‐

tom right ⇒ page 172 .
– Connect coolant hose with quick coupling -2- to charge air cir‐
cuit cooler bottom right ⇒ page 172 .
Vehicles with radiator version 3

– Connect coolant hose with quick coupling -arrow- to radiator

1. Cooling system 141

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect coolant hoses with quick coupling -1, 2- to charge air

circuit cooler ⇒ page 172 .
Continued for all vehicles

– Connect coolant hose with hose clamp -arrow- bottom to the

heating backup pump - V488- .
– Fill up the coolant reservoir -VAS 6096- with at least 8 litres of
pre-mixed coolant mixed to the correct ratio:
♦ ⇒ Maintenance ; Booklet Octavia III .

– Screw the adapter for cooling system testing device -

V.A.G 1274/8- to the coolant expansion tank.
– Mount cooling system charge unit - VAS 6096- onto the adapt‐
er -V.A.G 1274/8- .
– Lead the air hose -1- into a small container -2-.

Note

A small amount of coolant, which is entrained with the exhaust

air, must be collected.

– Close the valves -A- and -B-, while doing so turn the lever at
right angles to the direction of flow.
– Connect hose -3- to compressed air.
• Pressure: 0.6…1.0 MPa (6…10 bar)

142
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Rep. gr.19 - Cooling
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open the valve -B-, while doing so turn the lever in the direction
of flow.
• A vacuum pump is created in the cooling system by the vac‐
uum pump; the display instrument pointer must move into the
green area.
– In addition, briefly open the valve -A- by turning the lever in the
direction of flow, so that the hose of the coolant expansion
bottle is -VAS 6096- filled with coolant.
– Close the valve -A- again.
– Leave the valve -B- open a further 2 minutes.
• A vacuum pump is created in the cooling system by the vac‐
uum pump; the display instrument pointer must remain in the
green area.
– Close the valve -B-.
• If the display instrument pointer remains in the green area the
vacuum in the cooling system is sufficient for subsequent fill‐
ing.

Note

♦ If the pointer is below the green area, repeat the process.

♦ If the vacuum drops, you must check the cooling system for
leak points.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Disconnect pneumatic hose. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Open valve -A-.

• The vacuum pump in the cooling system draws the coolant out
of the coolant reservoir -VAS 6096- and fills the cooling sys‐
tem.
– Remove cooling system charge unit - VAS 6096- from coolant
expansion tank.

1. Cooling system 143

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Fill up coolant up to “Max” marking.

Note

Hose connections and air guide pipes and hoses must be free of
oil and grease before being installed.

– Install the noise insulation ⇒ Body Work; Rep. gr. 50 .

– For vehicles with auxiliary heating, switch it on for approxi‐
mately 30 seconds.
– Set temperature to “HI”.
– Switch off AC compressor. Press AC button to do so.
• The LED in the button must not illuminate.
– Fill and bleed coolant circuit ⇒ Vehicle diagnostic tester, Tar-
geted Functions , coolant circuit filling .

– Allow the engine to warm up until the thermostat has opened

or the radiator fan has been activated once.
– Allow engine to cool down.
– Check coolant level.
– Top up coolant to approximately 5 mm above the “Max” mark‐
ing.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Note with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

During driving, any residual air quantities are discharged via the
permanent vent lines.

– Check coolant level.

• If the engine is cold the coolant level must be between the
“Min” and “Max” marking.
• When the engine is at operating temperature the coolant level
may be at the “Max” marking.
– If necessary, top up with coolant.

1.5 Checking cooling system for leaks

Special tools and workshop equipment required
♦ Cooling system tester - V.A.G 1274 B-
♦ Adapter for cooling system tester - V.A.G 1274/8-
♦ Adapter for cooling system tester - V.A.G 1274/9-
Test prerequisite
• Engine must be warm.

144 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Test procedure

WARNING

Steam may escape when expansion tank is opened. Cover the

cap with a cloth and open carefully.

– Open cap -arrow- for coolant expansion tank.

– Position the cooling system testing device - V.A.G 1274 B- with

adapter -V.A.G 1274/8- onto the coolant expansion tank.
– Build up a pressure of approximately 0.1 MPa (1.0 bar) using
hand pump on cooling system tester.

WARNING

Risk of scalding!
♦ Before the cooling system testing device -V.A.G 1274 B-
is separated from the connecting hose or the connecting
piece -V.A.G 1274 B/1- , the existing pressure must ab‐
solutely be released.
♦ For this step, press the pressure relief valve on the cooling
system testing device -V.A.G 1274 B- and hold it pressed
until the pressure gauge indicates the value »0«.

If pressure drops:
– Search position of the leak andbyrepair
Protected copyright.fault.
Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Testing the pressure relief valve in the cap
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Screw the screw cap into the adapter for the cooling system
testing device -V.A.G 1274/9- .
– Connect the connecting piece -V.A.G 1274 B/1- to the adapter
for the cooling system testing device -V.A.G 1274/9- .

1. Cooling system 145

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect the connecting piece -V.A.G 1274 B/1- via the deliv‐
ered connecting hose to the cooling system testing device -
V.A.G 1274 B- .
– Operate the handpump.
• The pressure relief valve should open at a pressure of 0.14 ...
0.16 MPa (1.4 ... 1.6 bar).
If the pressure relief valve opens too early or too late:
– Renew cap.

146 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Coolant pump and coolant regulator

2.1 Summary of components - coolant pump and coolant thermostat

1 - O-rings
❑ replace after removal
❑ Moisten with coolant
2 - Inlet connections
3 - O-ring
❑ replace after removal
❑ Moisten with coolant
4 - Coolant pipe - front bottom
❑ removing and installing
⇒ page 158
5 - Sealing ring
❑ replace after removal
6 - O-ring
❑ replace after removal
❑ Moisten with coolant
7 - Coolant pump
❑ removing and installing
⇒ page 149
8 - O-rings
❑ replace after removal
❑ Moisten with coolant
9 - 8 Nm
10 - Coolant valve for cylinder
head - N489-
❑ removing and installing
⇒ page 151
11 - 20 Nm + torque a further
45° (1/8 turn)
❑ replace after removal
12 - Retaining clip
❑ check for firm seating
13 - Retaining clip
❑ check for firm seating
14 - O-ring
❑ replace after removal
❑ Moisten with coolant
15 - Sealing ring
❑ replace after removal
16 - 20 Nm
17 - Thermostat housingProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
18 - O-ring with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ replace after removal

2. Coolant pump and coolant regulator 147

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ Moisten with coolant
19 - Thermostat
❑ removing and installing ⇒ page 150
20 - 20 Nm
21 - Inlet connections

2.2 Summary of components - coolant temperature sender

1 - Coolant temperature send‐

er - G62-
❑ removing and installing
⇒ page 152
2 - Distance ring
❑ Renew if damaged.
3 - O-ring
❑ replace after removal
❑ Moisten with coolant
4 - Double screw, 8 Nm

148 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.3 Summary of components - electric coolant pump

Pump for charge air cooler - V188- , heating backup pump - V488-

1 - Charge air cooler pump -

V188-
❑ removing and installing
⇒ page 153
2 - Coolant hose
3 - Coolant hose
4 - 40 Nm
5 - 40 Nm
6 - Heating backup pump -
V488-
❑ removing and installing
⇒ page 154
7 - Coolant hose
8 - Coolant hose
9 - Bracket
❑ for heating backup
pump - V488-
10 - Brackets
11 - 40 Nm
12 - Bracket
❑ for charge air cooler
pump - V188-
13 - Brackets

2.4 Removing and installing coolant pump

Removing
– Drain coolant ⇒ page 139 .
– Remove the toothed belt from the camshaft ⇒ page 47 .

2. Coolant pump and coolant regulator 149

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screw -3-, pull off coolant valve for cylinder head -
N489- -Pos. 2-.
– Unscrew screws -arrows-, remove coolant pump -1-.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace O-rings after disassembly.

– Clean and smooth O-ring sealing surfaces.

– Moisten O-rings with coolant.
– install (set the timing) ⇒ page 52 .
– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - coolant pump and coolant thermo‐
stat
⇒ “2.1 Summary of components - coolant pump and coolant
thermostat”, page 147

2.5 Removing and installing thermostat

Removing
– Drain coolant ⇒ page 139 .
– Remove air filter ⇒Protected
page 334 .
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Unscrew screws -arrows-.
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Loosen hose clamp -2-, remove air guide pipe -1-.

For vehicles with engine identification characters CRKB

– Remove screws left and right -arrow-.

– Unscrew and remove the air guide pipe bottom - 1 -.
Continued for all vehicles

150 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock catch peg in -direction of arrow B- (from the top using

a screwdriver).
– Turn and pull off connection fittings -1- in -arrow direction A-.
– Remove thermostat.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Renew O-ring.

– Clean and smooth O-ring sealing surfaces.

– Moisten O-ring with coolant.

– Insert -2- into the thermostat housing.

• The retaining lungs must engage in the guides -arrows-.
– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - coolant pump and coolant thermo‐
stat
⇒ “2.1 Summary of components - coolant pump and coolant
thermostat”, page 147
♦ Summary of components - charge air cooler
⇒ “2.1 Charge air cooling - Summary of components”,
page 282
♦ Summary of components - air filter ⇒ page 332

2.6 Removing and installing coolant valve

for cylinder head - N489-
Removing
– Remove top toothed belt guard ⇒ page 43 .
– Disconnect electrical plug connection -2-, expose electric ca‐
ble.
– Unscrew screw -3-, pull off coolant valve for cylinder head -
N489- -Pos. 1-.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace O-rings after disassembly.

– Install top toothed belt guard ⇒ page 43 .

Tightening torques
♦ Summary of components - coolant pumpProtected
and coolant thermo‐
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
stat unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
⇒ “2.1 Summary of components - coolantwith
pump and coolant
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

thermostat”, page 147

2. Coolant pump and coolant regulator 151

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.7 Testing coolant thermostat

– Heat up the removed coolant regulator in a water bath.
Start of opening End of opening Opening stroke
87 ± 2 ℃ approximately 102 at least 9 mm
°C 1)
• 1) Cannot be tested.

2.8 Removing and installing coolant temper‐

ature sender - G62-
Removing
Test prerequisite
• Engine cold.
Procedure
– Briefly open the cap -arrow- for the coolant expansion reser‐
voir in order to remove the remaining pressure in the coolant
system.
– Remove air filter ⇒ page 334 .

– Unscrew screws -arrows-.

– Loosen hose clamp -2-, remove air guide pipe -1-.
Vehicles fitted with a manual gearbox
– Remove switching and selector linkage from gearbox, un‐
screw linkage support and lay aside with the linkages ⇒
Gearbox; Rep. gr. 34 .
Continued for all vehicles

– Expose electric wiring loom -1-.

– Release nut -4- and
unlessscrews
authorised -2, 3-. AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
by ŠKODA
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Push coolant pipes slightly to the left.

Note

♦ The left coolant pipes of version 1 are shown as an example.

♦ -Ignore arrows-.

152 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -1-.

– Unscrew double screw -2-, remove coolant temperature send‐
er - G62- .

Note

Use a wire to pull out any O-ring or distance ring that has re‐
mained stuck inside the cylinder head.

Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace O-rings after disassembly.

♦ Replace distance ring if it is damaged.

– Install the left coolant pipe ⇒ page 163 .

– Check coolant level ⇒ page 144 .
Tightening torques
♦ Summary of components - cylinder head
⇒ “1.4 Assembly overview - cylinder head”, page 85
♦ Summary of components - air filter ⇒ page 332
♦ Assembly overview - intake manifold
⇒ “6.1 Assembly overview - intake manifold”, page 325
♦ Summary of components - gearshift mechanism ⇒ Gearbox;
Rep. gr. 34

2.9 Removing and installing charge air cool‐

er pump - V188-
Special tools and workshop equipment required
♦ Hose clamps up to ∅ 25 mm - MP7-602 (3094)-
♦ Hose clip pliers - VAS 6362-
Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50by.copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Protected
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2. Coolant pump and coolant regulator 153

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -3-.

Note

Place a cloth below to catch any leaking coolant.

– Disconnect coolant hoses with hose clamps -MP7-602

(3094)- .
– Loosen hose clamps -2-, remove coolant hoses.
– Unhook pump for charge air cooler - V188- - Pos. 1- out of the
retaining strap -4-.
Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Check coolant level ⇒ page 144 .

Tightening torques
♦ Summary of components - electric coolant pump
⇒ “2.3 Summary of components - electric coolant pump”, page
149
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

2.10 Removing and installing the heating

backup pump - V488-
Special tools and workshop equipment required
♦ Hose clamps up to ∅ 25 mm - MP7-602 (3094)-
♦ Hose clip pliers - VAS 6362-
Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .

154 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -3-.

Note

Place a cloth below to catch any leaking coolant.

– Disconnect coolant hoses with hose clamps -MP7-602

(3094)- .
– Loosen hose clamps -4-, remove coolant hoses.
– Unhook heating backup pump cooler - V488- - Pos. 2- out of
the retaining strap -1-.
Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Check coolant level ⇒ page 144 .

Tightening torques
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

2. Coolant pump and coolant regulator 155

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 Coolant pipes

3.1 Summary of components - coolant pipe

Note

The arrows on the coolant pipes and the coolant hose ends must stand opposite to each other.

1 - 10 Nm
2 - Coolant pipe - front right
❑ removing and installing
⇒ page 162
3 - 10 Nm
4 - 10 Nm
5 - Coolant pipe - front top
❑ removing and installing
⇒ page 157
6 - Coolant pipe - bottom right
❑ removing and installing
⇒ page 165 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
7 - O-ring with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ replace after removal

❑ Moisten with coolant
8 - 10 Nm
9 - 23 Nm
10 - 10 Nm
11 - The coolant pipe at the
rear
❑ removing and installing
⇒ page 164
12 - 10 Nm
13 - 10 Nm
14 - 10 Nm
15 - Coolant pipe - front left.
❑ removing and installing
⇒ page 160
16 - 10 Nm
17 - Coolant pipe - left
❑ different designs; assignment ⇒ ETKA - Electronic Catalogue of Original Parts
❑ removing and installing ⇒ page 163
18 - 8 Nm
19 - 8 Nm

156 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3.2 Removing and installing the front top

coolant pipes
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
Removing
– Remove engine cover at the top ⇒ page 9 .
– Drain coolant ⇒ page 139 .
– Release screws -1, 3-.
– Unlock catch -arrows-, remove cover-2-.

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove top part-1- of air guide.

– Release screw left and right -arrow-.

– Unclip and remove bottom part -1- of air guide.

3. Coolant pipes 157

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip bracket -1- with fuel hoses.

– Unscrew screws -arrows-.
– Loosen hose clamp -3-, remove coolant hose.

Note

-Do not pay attention to the position 2-.

For vehicles with engine identification characters CLHA, CLHB,

CKFB, CKFC, CUPA, CRVC

– Release screws -1, 2-.

– Loosen hose clamps -arrows-, remove coolant hoses.
– Install the front top coolant pipes.
For vehicles with engine identification characters CRKB

– Release screws -1, 2-.

– Loosen hose clamps -arrows-, remove coolant hoses.
– Install the front top coolant pipes.
Install
Installation is performed in a similar way in the reverse order. Pay
attention to the following points:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Top up coolant ⇒ page 140 .

Tightening torques
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - air filter ⇒ page 332

3.3 Removing and installing the front bottom

coolant pipe
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
Removing
– Remove oil filter holder ⇒ page 121 .

158 Rep. gr.19 - Cooling

with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -arrows-.

– Loosen hose clamp -2-, remove air guide pipe -1-.
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CUPA, CRVC

– Release screws -arrows-, push the holder -1- with electric wir‐
ing loom slightly to the side.
For vehicles with engine identification characters CRKB
– Remove throttle valve module - J338- ⇒ page 327 .
Continued for all vehicles:

– Raise hose clamp -4-, remove coolant hose.

– Unscrew screws -arrows-.
– Pull off locking clip -2-, pull off coolant thermostat housing
-3- from bottom front -1- and remove.

– Loosen hose clamp -1-, remove coolant hose.

– Release screw -4-.
– Pull off coolant pipe bottom front -3- and remove, do not dam‐
age the vacuum line -2- when doing so.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace gaskets and O-rings after disassembly.

♦ Secure all hose connection ends with spring-type clips that
comply with the series design ⇒ ETKA - Electronic Catalogue
of Original Parts .

– Clean and smooth gasket and O-ring sealing surfaces.

– Moisten gaskets and O-rings with coolant.
– Install oil filter holder ⇒ page 121 .
– Connect coolant hose with quick coupling ⇒ page 172 .
– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - coolant pump and coolant thermo‐
stat
⇒ “2.1 Summary of components - coolant pump and coolant
thermostat”, page 147
♦ Assembly overview - intake manifold
⇒ “6.1 Assembly overview - intake manifold”, page 325

3.4 Removing and installing the front left

coolant pipe
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
Removing
– Remove engine cover at the top ⇒ page 9 .
– Drain coolant ⇒ page 139 .
– Release screws -1, 3-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Unlock catch -arrows-, remove cover-2-.

160 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove top part-1- of air guide.

– Release screw left and right -arrow-.

– Unclip and remove bottom part -1- of air guide.
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CUPA, CRVC

– Raise holding clamp -1-, remove coolant connection fittings.

– Release screw -2-.
– Loosen hose clamps -arrows-, removeProtected
coolant hoses.Copying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Remove the front left coolant pipe. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

For vehicles with engine identification characters CRKB

– Remove air filter ⇒ page 334 .

3. Coolant pipes 161

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Raise holding clamp -1-, remove coolant connection fittings.

– Release screw -2-.
– Loosen hose clamps -arrows-, remove coolant hoses.
– Remove the front left coolant pipe.
Install
Installation is performed in a similar way in the reverse order. Pay
attention to the following points:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Top up coolant ⇒ page 140 .

Tightening torques
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - air filter ⇒ page 332

3.5 Removing and installing the front right

coolant pipe
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6340-
♦ Hose clip pliers - VAS 6362-
Removing
– Drain coolant ⇒ page 139 .
– Remove V-ribbed belt ⇒ page 36 .
– Remove AC compressor with connected refrigerant hoses
from the holder ⇒ Heating, Air Conditioning; Rep. gr. 87 and
strap up to the right side.

162 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen hose clamps -1, 4, 6-, remove coolant hoses.

– Release nut -5- and screw -2-.
– Expose coolant hoses -3-, remove front right coolant hose.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Install poly V-belt ⇒ page 36 .

– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Removing and installing AC compressor ⇒ Heating, Air Con‐
ditioning; Rep. gr. 87 .

3.6 Remove and install the left coolant pipes

Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6340-
Removing
– Drain coolant ⇒ page 139 .
– Remove air filter ⇒ page 334 .
– Unscrew screws -arrows-.
– Loosen hose clamp -2-, remove air guide pipe -1-.
Vehicles fitted with manual gearbox 02Q
– Remove switching and selector linkage from gearbox, un‐
screw linkage support and lay aside with the linkages ⇒
Gearbox; Rep. gr. 34 .
Vehicles with coolant hoses left version 1

3. Coolant pipes 163

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Expose electric wiring loom -1-.

– Release nut -4- and screws -2, 3-.
– Loosen hose clamps -arrows-, remove coolant hoses.
– Remove the left coolant pipes.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Replenish coolant ⇒ page 140 .

Tightening torques
♦ Hose connections with Protected
screw by clamps
copyright.⇒ pagefor281
Copying private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Summary of componentswith
- coolant pipe
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - air filter ⇒ page 332
♦ Assembly overview - intake manifold
⇒ “6.1 Assembly overview - intake manifold”, page 325
♦ Summary of components - actuation linkages ⇒ Gearbox;
Rep. gr. 34

3.7 Removing and installing the rear coolant

pipe
Special tools and workshop equipment required
♦ Catch pan , e.g. -VAS 6208-
♦ Hose clip pliers - VAS 6340-
♦ Hose clip pliers - VAS 6362-
Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .
Vehicles with four-wheel drive
– Remove pre-exhaust pipe ⇒ page 349 .
– Release screws -arrow-, remove heat shield -1-.
Continued for all vehicles
– Place catch pan - VAS 6208- underneath.

164 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen hose clamp-4-, remove coolant hose, allow coolant to

drain.
– Loosen hose clamps -1-, remove coolant hoses.
– Release nut -3- and screw -2-, remove rear coolant pipe.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Secure all hose connections with spring-type clips that comply

with the series design ⇒ ETKA - Electronic Catalogue of Original
Parts .

– Replenish coolant ⇒ page 140 .

Tightening torques
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

3.8 Removing and installing the rear right

coolant pipe
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
Removing Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Note

Fit all heat protection sleeves on again in the same place when
installing.

– Remove engine cover at the top ⇒ page 9 .

– Drain coolant ⇒ page 139 .
– Remove rear coolant pipe ⇒ page 164 .
– Remove left coolant pipe ⇒ page 163 .
– Remove pre-exhaust pipe ⇒ page 349 .
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CUPA, CRVC
– Open heat protection sleeve -1-.
– Take electrical plug connection-4 - out of the holder, discon‐
nect and expose electric cable.
– Disconnect electrical plug connections -3, 5-, expose electric
wiring loom.
– Unscrew screw -2-, lay bracket with differential pressure send‐
er - G505- to the rear.
For vehicles with engine identification characters CRKB

3. Coolant pipes 165

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open heat protection sleeve -1-.

– Disconnect electrical plug connections -3, 4,5, 6- expose elec‐
tric wire harness.
– Release screw -2-.

– Detach vacuum hose -arrow- and put to one side.

– Place the bracket with the differential pressure indicator to the
rear.
Continued for all vehicles

– Press release buttons on the hose -1- for crankcase ventila‐

Note

-Do not pay attention to the position 3-.

– Loosen hose clamp -1-, remove coolant hose.

– Unscrew screw -2-, remove screw -3- and swivel coolant line
to the side.

166 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Expose the following plug connections and electric cables:

2 - for exhaust gas temperature sender 4 - G648-
3 - for exhaust gas temperature sender 3 - G495-
4 - for lambda probe - G39-

Vehicles fitted with auxiliary heating

– Release screws -arrows-, push the coolant pipe slightly to the
side.

Note

-Do not pay attention to positions 1, 2, 3-.

Vehicles with four-wheel drive

– Remove the right driveshaft from the angle gearbox ⇒ Sus‐
pension; Rep. gr. 40 .
Continued for all vehicles
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Press heattoprotection
with respect the correctnesssleeve to the
of information in thisside, disconnect
document. Copyright by electrical
ŠKODA AUTO A. S.�
plug connection -5-.
– Loosen hose clamp -3-, remove air guide hose.
– Loosen hose clamp -4-, remove coolant hose.
– Unscrew screw -1-, loosen screw -2-.

Note

-Do not pay attention to the position 6-.

– Loosen screw -1- and remove clamping sleeve.

– Slacken the double screw -2-, press coolant pipe backwards
slightly.
– Unscrew screws -arrows-, push exhaust gas cleaning module
and exhaust gas recirculation cooler backwards.

3. Coolant pipes 167

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen hose clamp -1-, remove coolant hose.

– Unscrew double screw -2- and screw -3-, remove rear right
coolant pipe.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace O-ring after disassembly.

♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

– Install exhaust gas cleaning module ⇒ page 360 .

– Install pre-exhaust pipe ⇒ page 349 .
– Install the rear coolant pipe ⇒ page 164 .
– Install the left coolant pipe ⇒ page 163 .
– Replenish coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - coolant pipe
⇒ “3.1 Summary of components - coolant pipe”, page 156
♦ Removing and installing exhaust pipes/silencers
⇒ page 340
♦ Summary of components - cardan shaft ⇒ Chassis; Rep. gr.
40

168 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4 Radiator and radiator fan

4.1 Parts of the cooling system fitted to body

Radiator version 1

1 - Coolant radiator
❑ removing and installing
⇒ page 173
❑ fill with fresh coolant af‐
ter replacing
2 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
3 - Not installed
4 - Not installed
5 - Not installed
6 - O-ring
❑ replace after removal
❑ Moisten with coolant
7 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
8 - O-ring
❑ replace after removal
❑ Moisten with coolant
9 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
10 - Radiator bearing
❑ if the fuse breaks, re‐
place it with a special
screw, see ⇒ ETKA -
Electronic Catalogue of Original Parts
11 - Cooler for charge air circuit
❑ removing and installing ⇒ “4.4 Removing and installing radiator”, page 173
12 - Capacitors
❑ removing and installing ⇒ Heating, Air Conditioning; Rep. gr. 87
13 - Rubber bush
❑ for radiator
14 - O-ring
❑ replace after removal
❑ Moisten with coolant
15 - Coolant hose
❑ to remove, raise holding
Protected byclamps
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

4. Radiator and radiator fan 169

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ connect ⇒ page 172
16 - O-ring
❑ replace after removal
❑ Moisten with coolant

Radiator version 2

1 - Coolant radiator
❑ removing and installing
⇒ page 173
❑ fill with fresh coolant af‐
ter replacing
2 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
3 - O-ring
❑ replace after removal
❑ Moisten with coolant
4 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
5 - O-ring
❑ replace after removal
❑ Moisten with coolant
6 - Cooler for charge air circuit
❑ removing and installing
⇒ “4.4 Removing and in‐
stalling radiator”,
page 173
7 - Radiator bearing
❑ if the fuse breaks, re‐
place it with a special
screw, see ⇒ ETKA -
Electronic Catalogue of
Original Parts
8 - Capacitors
❑ removing and installing ⇒ Heating, Air Conditioning; Rep. gr. 87
9 - Rubber bush
❑ for radiator
10 - O-ring
❑ replace after removal
❑ Moisten with coolant
11 - Coolant hose
❑ to remove, raise holding clamps
❑ connect ⇒ page 172
12 - O-ring
❑ replace after removal
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Moisten with coolant
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

170 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

13 - Coolant hose
❑ to remove, raise holding clamps
❑ connect ⇒ page 172

Radiator version 3

1 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
2 - O-ring
❑ replace after removal
❑ Moisten with coolant
3 - Cooler for charge air circuit
❑ removing and installing
⇒ “4.4 Removing and in‐
stalling radiator”,
page 173
4 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
5 - O-ring
❑ replace after removal
❑ Moisten with coolant
6 - Coolant hose
❑ to remove, raise holding
clamps
❑ Connect ⇒ page 172
7 - O-ring
❑ replace after removal
❑ Moisten with coolant
8 - Coolant radiator
❑ removing and installing
⇒ page 173
❑ fill with fresh coolant af‐
ter replacing
9 - Capacitors
❑ removing and installing ⇒ Heating, Air Conditioning; Rep. gr. 87
10 - Radiator bearing
❑ if the fuse breaks, replace it with a special
Protected screw,
by copyright. see
Copying ⇒ ETKA
for private - Electronic
or commercial Catalogue
purposes, in ofisOriginal
part or in whole, not permittedParts
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
11 - Rubber bush with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ for radiator
12 - O-ring
❑ replace after removal
❑ Moisten with coolant
13 - Coolant hose
❑ to remove, raise holding clamps

4. Radiator and radiator fan 171

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ connect ⇒ page 172

Connect coolant hose with quick coupling

– Remove old O-ring -2- in coolant hose -3-.
– Moisten new O-ring with coolant and insert into coolant hose.
– Press coolant hose onto connection -1- until there is an audible
click.
– Press coolant hose down again and check by pulling that the
plug-in connector is fully engaged.

4.2 Summary of components - fan shroud and radiator fan - V7-

1 - 5 Nm
2 - Fan shroud
❑ removing and installing
⇒ page 177
3 - Radiator fan - V7-
❑ removing and installing
⇒ page 178

172 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.3 Summary of components- fan shroud and radiator fan - V7- and radiator fan
2 - V177-

1 - 5 Nm
2 - Fan shroud
❑ removing and installing
⇒ page 177
3 - 5 Nm
4 - Radiator fan - V7-
❑ removing and installing
⇒ page 178
5 - Radiator fan 2 - V177-
❑ removing and installing
⇒ page 178

4.4 Removing and installing radiator

Note

Coolant radiator and charge air circulation cooler are removed

together.

Removing
– Drain coolant ⇒ page 139 .
– Remove front bumper ⇒ Body Work; Rep. gr. 63 .

4. Radiator and radiator fan 173

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -1, 3-.

– Unlock catch -arrows-, remove cover-2-.

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove top part-1- of air guide.

– Release screw left and right -arrow-.

– Unclip and remove bottom part -1- of air guide.
– Removing fan shroud ⇒ page 177 .
Vehicles with radiator versions 1 and 2

– Raise holding clamp -arrow-, remove coolant hose right above

radiator for charge air circuit.
Vehicles with radiator version 3

174 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Raise holding clamp -arrow-, remove bottom left coolant hose

from radiator.

– Raise holding clamps -1, 2-, remove coolant hoses from

charge air circuit cooler.
Continued for all vehicles

– Raise holding clamp -arrow-, remove top left coolant hose

from radiator.

– Press catches left and right -arrows-, press coolant radiator

slightly backwards.

4. Radiator and radiator fan 175

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

If the fuse breaks, you will not need to replace the radiator bearing
-1-. Replace the fuse with a special fuse -3- ⇒ ETKA - Electronic
Catalogue of Original Parts .

– Unlock the latches left and right -arrow A- and raise the con‐
denser -2-.
– Press the radiator downwards until the radiator bearing de‐
flects at the bottom, to do so, unhook the condenser -2- from
the radiator.
– Strap capacitor to the lock support.
Vehicles with radiator versions 1 and 2 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Press left and right radiator locking lugs simultaneously

-arrow- and remove coolant radiator from the charge air circuit
radiator.
Vehicles with radiator version 3

176 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock catches on the radiator -1- for the charge air circuit
-arrows A-
– Remove charge air circuit radiator from coolant radiator -2-
-arrow B-and unhook -arrow C-.
– Remove both radiators.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace O-rings after disassembly.

– Install front bumper ⇒ Body Work; Rep. gr. 63 .

– Install fan shroud ⇒ page 177 .
– Connect coolant hose with quick coupling ⇒ page 172 .
– Replenish coolant ⇒ page 144 .

Note

If the radiator has been replaced you must change all the coolant.

Tightening torques
♦ Parts of the cooling system fitted to body
⇒ “4.1 Parts of the cooling system fitted to body”, page 169
♦ Summary of components - air filter ⇒ page 332

4.5 Removing and installing fan shroud

Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
gr. 50 . with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Disconnect electric plug connection -1- for radiator fan, for this
purpose slide screw clamp backwards -arrow A- and press
plug connection down.
– Press locking lugs for fan shroud left and right simultaneously
-arrow B- and remove fan shroud downwards from the radia‐
tor.
Install
Installation is carried out in the reverse order.
Tightening torques
♦ Summary of components - sound damping system ⇒ Body
Work; Rep. gr. 50

4. Radiator and radiator fan 177

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.6 Removing and installing radiator fans -

V7- and -V177-
Removing

Note

All cable straps should be fitted on again in the same place when
installing.

– Removing fan shroud ⇒ page 177 .

For vehicles with a fan
– Expose electric cable.
– Unscrew screws -arrows-, remove - V7- radiator fan.
For vehicles with two fans

– Disconnect plug connection -arrow-.

– Remove screws -1- and remove the radiator fan - V7- .
– Unscrew screws -2- and radiator fan 2 - V177- .
Install Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Installation is performed in the reverse order, pay attention to the
following points:
– Install fan shroud ⇒ page 177 .
Tightening torques
♦ Summary of components - fan shroud and radiator fan - V7-
⇒ page 172
♦ Summary of components- fan shroud and radiator fan - V7-
and radiator fan 2 - V177- ⇒ page 173

178 Rep. gr.19 - Cooling

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

20 – Fuel supply system

1 Measures in case of misfuelling

Note

♦ Fuel lines are secured with quick-release couplings

⇒ page 226 .
♦ Fuel hoses must only be secured with spring-type clips ⇒ ET‐
KA - Electronic Catalogue of Original Parts .
♦ Use pliers for spring strap clips to fit the hose clamps.

Observe safety precautions ⇒ page 4 .

Observe rules for cleanliness ⇒ page 6 .

Caution

Because of insufficient lubrication by diesel fuel, misfuelling

can cause irreversible damage to high pressure components,
particularly the high pressure pump.
♦ Damage can be expected in the form of scoring and par‐
ticle erosion.
♦ Thus, free metal particles contaminate the fuel system as
well as the injection system, whereby further damage can
be expected especially to the fuel pressure regulating
valve and in the injection units.
♦ If there is uncertainty about the fuel quality, take a sample.
Analyse the fuel using the fuel analyser - VAS 6774- ⇒
Operating manual . This analyser does not replace labo‐
ratory analysis in the event of warranty claims!

Note

Operating instructions must be provided in the form of a flow chart

taking account of the various factors
unless through
authorised individual work AUTO
AUTO A. S. ŠKODA se‐ A. S. does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
by ŠKODA
quences. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

If the engine was started with incorrect fuel?

Yes
⇒ “1.1 Step 1, engine started with incorrect fuel”, page 179
No
⇒ “1.2 Step 2, the engine was not started with incorrect fuel”,
page 181

1.1 Step 1, engine started with incorrect fuel

– Empty fuel tank as far as possible through the filler neck using
the fuel extraction device - VAS 5190- ⇒ page 202 .
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

1. Measures in case of misfuelling 179

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- for closing flange with the disassembly wedge
- 3409- on the retaining tabs -arrows-.

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

WARNING

Ensure that when the battery is connected the fuel pump can‐
not be activated by the opening door! Fuel can spill out when
the system is open.

180 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect fuel return line -2- at the closing flange. Unlock the
quick coupling and disconnect ⇒ page 226 .
– Connect line connecting line - VAS 6551/1- of the pressure
gauge to the fuel return line.
– If necessary, extend the connecting line - VAS 6551/1- using
the connecting nipple - VAS 6551/5-1- and a commercially
available hose.
– Guide the free end of the line connecting line - VAS 6551/1-
into a suitable container.
– Connect a vehicle diagnosis tester .
– Perform Targeted Functions empty fuel tank .

Note

The fuel pump is now activated.

– If necessary, repeat this procedure until the fuel tank is com‐

pletely empty.
Remove fuel delivery unit ⇒ page 210 .
– Check the fuel tank for swarfs.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Empty fuel pump reservoir of the fuel delivery unit.
– Carry out a visual inspection for coarse contamination and
swarfs in the fuel pump reservoir and on the preliminary stage
screen.
Are swarfs present?
Yes
⇒ “1.3 Step 3, metal swarfs are present in the fuel delivery unit
and the fuel tank”, page 182
No
⇒ “1.4 Step 4, no metal swarfs are present in the fuel delivery
unit and the fuel tank”, page 183

1.2 Step 2, the engine was not started with

incorrect fuel
– Empty fuel tank as far as possible through the filler neck using
the fuel extraction device - VAS 5190- ⇒ page 202 .
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- for closing flange with the disassembly wedge
- 3409- on the retaining tabs -arrows-.

1. Measures in case of misfuelling 181

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

WARNING

Ensure that when the battery is connected the fuel pump can‐
not be activated by the opening door! Fuel can spill out when
the system is open.

Note

The fuel pump is now activated.

– If necessary, repeat this procedure until the fuel tank is com‐

pletely empty.
– Fill fuel tank with 5 litres of diesel fuel.
– Empty fuel tank again fully as described above.

– Reconnect the fuel return line -2-.

– Replace the fuel filter ⇒ page 196 .
– Fill vehicle tank and take it for a test run.
End

1.3 Step 3, metal swarfs are present in the

fuel delivery unit and the fuel tank
– Clean, for example
Protected using for
by copyright. Copying fuel delivery
private unitpurposes,
or commercial and fuel tank
in part or in with
whole, is not permitted
diesel suction
unless authoriseddevice
by ŠKODA -VAS
AUTO 5226-
A. S. ŠKODA. AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Install fuel delivery unit ⇒ page 210 .

182 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Vehicles fitted with auxiliary heating

– Check the fuel line between the fuel tank and dosing pump -
V54- for swarfs. Replace where necessary ⇒ Heating, Air
Conditioning; Rep. gr. 82 .
Continued for all vehicles
– Fill fuel tank with 5 litres of diesel fuel.
– Empty fuel tank again fully as described above ⇒ page 179 .
– Replace the following high pressure components:
♦ High pressure pump ⇒ page 310 .
♦ High pressure lines ⇒ page 305 .
♦ Fuel distributor including fuel pressure control valve - N276-
and fuel pressure sender - G247- ⇒ page 307 .
♦ Injector ⇒ page 303 .
♦ Fuel return-flow lines (waste fuel lines) ⇒ page 295 .
♦ Fuel filter ⇒ page 196 .
– Fill vehicle tank.
– Venting air from the fuel system ⇒ page 293 .
– Perform a test drive.
End

1.4 Step 4, no metal swarfs are present in

the fuel delivery unit and the fuel tank
– Fill fuel tank with 5 litres of diesel fuel.
– Empty fuel tank again fully as described above ⇒ page 179 .

WARNING

When removing the fuel dosage valve from the high pressure
pump, there is the risk that dirt may get into the pump whereby
damage to the pump could occur. Therefore, clean the fuel
dosage valve as well as the high pressure pump as thoroughly
as possible before removing, while doing so observe the rules
of cleanliness when working on Protected the injection system
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
⇒ page 6 . unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Disconnect the plug from the valve.

– Unscrew the screws -arrows- and carefully remove the fuel
dosage valve - N290- -A- from the high pressure pump.
– Check fuel dosing valve - N290- and high pressure pump for
swarfs.
Are swarfs present?
Yes
⇒ “1.5 Step 5, metal swarfs are present in the high pressure
pump”, page 184
No
⇒ “1.6 Step 6: no metal swarfs are present in the high pressure
pump”, page 184

1. Measures in case of misfuelling 183

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.5 Step 5, metal swarfs are present in the

high pressure pump
– Replace the following high pressure components:
♦ High pressure pump ⇒ page 310 .
♦ High pressure lines ⇒ page 305 .
♦ Fuel distributor including fuel pressure control valve - N276-
and fuel pressure sender - G247- ⇒ page 307 .
♦ Injector ⇒ page 303 .
♦ Fuel return-flow lines (waste fuel lines) ⇒ page 295 .
♦ Fuel filter ⇒ page 196 .
– Fill vehicle tank.
– Venting air from the fuel system ⇒ page 293 .
– Perform a test drive.
End

1.6 Step 6: no metal swarfs are present in

the high pressure pump

WARNING

Watch out for damages to gasket rings for fuel dosage valve -
N290- . If a gasket ring is damaged, the high pressure pump
must be replaced. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Wet the lower gasket ring for fuel dosage valve - N290- with
fuel.
– Slide the valve into the high pressure pump with light rotary
movements.
– Screw in screws -arrows- only by hand.
– Pre-tighten screws to 3 Nm, then fully tighten to 7 Nm.
– Replace the fuel filter ⇒ page 196 .
– Venting air from the fuel system ⇒ page 293 .
– Fill vehicle tank and take it for a test run.
End

184 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Removing and installing parts of the

fuel supply system

2.1 Fuel tank with attached parts, vehicles

with front-wheel drive - Summary of
components
For vehicles with multi-control arm rear axle

1 - Screw cap
❑ Pull until it can be heard
clicking into place
❑ with securing to prevent
any loss during tank fuel
filler flap operation
2 - Earth connection
❑ for fuel filler neck
❑ for discharging the elec‐
trostatic charge
⇒ page 188
3 - Vent end piece
❑ Fitting position
⇒ page 189
4 - 8 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
❑ for attaching the fuel fill‐
er neck
5 - Lock ring, 110 Nm
6 - Sealing ring
❑ replace
❑Protected
use bydry for fitting
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
7 - Fuel
with delivery
respect to theunit
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ Summary of compo‐
nents ⇒ page 192
❑ removing and installing
⇒ page 210
❑ with sender for fuel
gauge display - G-
❑ Removing and installing
fuel gauge sender - G-
⇒ page 223 .
❑ inspecting fuel pump ⇒ page 249
❑ note the correct installed position of the fuel tank ⇒ page 189
8 - Fuel tank
❑ removing and installing ⇒ page 230
9 - Heat shield
❑ for fuel tank
10 - Circlip
❑ for heat shield

2. Removing and installing parts of the fuel supply system 185

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

11 - Tensioning strap
❑ Check fitting position
❑ before removing, mark running direction
12 - 20 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
❑ New screws for tensioning strap are longer, note the part number⇒ ETKA - Electronic Catalogue of
Original Parts
13 - Support
❑ For fuel pump control unit - J538-
❑ Removing and installing fuel pump control unit - J538- ⇒ page 240
14 - Support
❑ for vehicles with auxiliary heating
❑ for dosing pump - V54-
15 - Fuel line
❑ for vehicles with auxiliary heating from the dosing pump - V54-
❑ do not kink
❑ check for firm seating
16 - Fuel feed line
❑ to fuel filter
❑ Clipped onto fuel tank.
❑ check for firm seating
❑ do not kink
❑ Fit so that it can be heard clicking into place
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
17 - Fuel return line
❑ of engine
❑ Clipped onto fuel tank.
❑ check for firm seating Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ do not kink with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ Fit so that it can be heard clicking into place

❑ Unlock the quick coupling and disconnect ⇒ page 226 .
18 - Dosing pump - V54-
❑ for vehicles with auxiliary heating

For vehicles with torsion beam rear axle

186 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Screw cap
❑ Pull until it can be heard
clicking into place
❑ with securing to prevent
any loss during tank fuel
filler flap operation
2 - Earth connection
❑ for fuel filler neck
❑ for discharging the elec‐
trostatic charge
⇒ page 188
3 - 8 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
❑ for attaching the fuel fill‐
er neck
4 - Vent end piece
❑ Fitting position
⇒ page 189
5 - Lock ring, 110 Nm
6 - Sealing ring
❑ replace
❑ use dry for fitting
7 - Fuel delivery unit
❑ Summary of compo‐ Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
nents ⇒ page 192unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ removing and installing
⇒ page 210
❑ with sender for fuel
gauge display - G-
❑ Removing and installing
fuel gauge sender - G-
⇒ page 223 .
❑ inspecting fuel pump ⇒ page 249
❑ note the correct installed position of the fuel tank ⇒ page 189
8 - Fuel tank
❑ removing and installing ⇒ page 230
9 - Heat shield
❑ for fuel tank
10 - Circlip
❑ for heat shield
11 - Tensioning strap
❑ Check fitting position
❑ before removing, mark running direction
12 - 20 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
❑ New screws for tensioning strap are longer, note the part number⇒ ETKA - Electronic Catalogue of
Original Parts
13 - Support
❑ For fuel pump control unit - J538-
❑ Removing and installing fuel pump control unit - J538- ⇒ page 240

2. Removing and installing parts of the fuel supply system 187

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

14 - Support
❑ for vehicles with auxiliary heating
❑ for dosing pump - V54-
❑ Pay attention to correct fit of the dosing pump - V54- in the holder
15 - Fuel line
❑ for vehicles with auxiliary heating from the dosing pump - V54-
❑ do not kink
❑ check for firm seating
16 - Fuel feed line
❑ to fuel filter
❑ Clipped onto fuel tank.
❑ check for firm seating
❑ do not kink
❑ Fit so that it can be heard clicking into place
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
17 - Fuel return line
❑ of engine
❑ Clipped onto fuel tank.
❑ check for firm seating
❑ do not kink
❑ Fit so that it can be heard clicking into place
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
18 - Dosing pump - V54-
❑ for vehicles with auxiliary heating

Earth connection for fuel filler neck

– Connect earth connection as shown in the illustration.
– Ensure the quick coupling fits tightly:
♦ Plug -2- of the earth connection on the threaded ring -3- of the
fuel filler neck.
– Unhook contact peg -1- of the earth connection in the securing
bore on the fuel tank -4- and press in the distance sleeve -5-.

WARNING

Risk from electrostatic charge. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ After installing, use an ohmmeter to test the electrical con‐
nection of the threaded ring on the fuel filler neck at a bare
point on the body.
• Specified value approximately 0 Ω.

188 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Fitting location of the fuel delivery unit

• Arrow -3- at the fuel tank must show marking -2- at the lock
ring -1-

Fuel line at the fuel delivery unit

1- Fuel feed line
2- Fuel return line
3- Fuel line to the dosing pump - V54-

Installation position of the vent end piece

When installing the fuel tank -2-, note the installation position of
the vent end piece -1-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• Angle -α- must be 60°.

2.2 Fuel tank with attached parts, vehicles with four-wheel drive - Summary of
components

2. Removing and installing parts of the fuel supply system 189

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Screw cap
❑ close by turning until it
audibly locks into place
❑ with securing to prevent
any loss during tank fuel
filler flap operation
2 - 8 Nm + torque a further 90°
(1/4 turn)
❑ replace after removal
3 - Earth connection
❑ for fuel filler neck
❑ for discharging the elec‐
trostatic charge
⇒ page 191
4 - Vent end piece
❑ Fitting position
⇒ page 192
5 - Fuel delivery unit
❑ Summary of compo‐
nents ⇒ page 194
❑ removing and installing
⇒ page 214
❑ with sender for fuel
gauge display - G-
❑ Removing and installing
fuel gauge sender - G-
⇒ page 223 .
❑ inspecting fuel pump
⇒ page 249
❑ note the correct instal‐
led position of the fuel
tank ⇒ page 191
6 - Rubber buffer
❑ between fuel tank and bodyshell
❑ pay attention to correct position
7 - 20 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
8 - Guide
9 - Fuel tank
❑ removing and installing ⇒ page 236
10 - 20 Nm + torque a further 90° (1/4 turn)
❑ replace after removal
11 - Tensioning strap
❑ Check fitting position
12 - Circlip
❑ for heat shield
13 - Heat shield
❑ check for firm seating
14 - Connected fuel hoses
❑ do not kink Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

190 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
❑ observe the arrow direction (feed or return line) on the closing flange when installing
❑ clipped in place on fuel tank
15 - Support
❑ For fuel pump control unit - J538-
❑ Removing and installing fuel pump control unit - J538- ⇒ page 240

Earth connection for fuel filler neck

WARNING

Risk from electrostatic charge.

♦ After installing, use an ohmmeter to test the electrical con‐
nection of the threaded ring on the fuel filler neck at a bare
point on the body.
• Specified value approximately 0 Ω.

Fitting location of the fuel delivery unit

• Arrow -3- at the fuel tank must show marking -2- at the lock
ring -1-

Fuel line at the fuel delivery unit

1- Fuel feed line
2- Fuel return-flow line
3- Fuel line to the dosing pump - V54-

2. Removing and installing parts of the fuel supply system 191

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of the vent end piece

When installing the fuel tank -2-, note the installation position of
the vent end piece -1-.
• Angle -α- must be 60°.

2.3 Fuel delivery unit, vehicles with front-wheel drive - Summary of components

1 - Fuel delivery unit

❑ With fuel system pres‐
surisation pump - G6-
❑ electrical testing of the
fuel pump in Targeted
fault finding ⇒ Vehi‐
cle diagnostic tester Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ inspecting fuel pump unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
⇒ page 249
❑ removing and installing
⇒ page 210
❑ Fill the vehicle with at
least 5 litres of fuel after
installing
❑ after installing a new
fuel delivery unit it will be
necessary to unscrew
the screw plug from the
connection on the fuel
delivery unit in order to
connect the fuel line of
the auxiliary heating
2 - Sealing ring
❑ replace
❑ install when dry
3 - Lock ring, 110 Nm
❑ loosen and/or tighten
using wrench - T30101
(3087)-

Note

Ensure that the fuel delivery unit is

not damaged when loosening and
tightening the lock ring of the holder
on the flange.

192 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4 - Fuel feed line

❑ to fuel filter
❑ pushed into the fuel tank
❑ do not kink
❑ to remove, press release button at connecting piece
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
❑ observe the arrow direction (feed or return line) on the closing flange when installing
❑ Fit so that it can be heard clicking into place
❑ Press down again and check by pulling that the plug-in connector is fully engaged.
5 - Fuel pump control unit - J538-
❑ check in Targeted fault finding ⇒ Vehicle diagnostic tester
❑ removing and installing ⇒ page 240
6 - Electrical plug connection
❑ For fuel pump control unit - J538-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
7 - Electrical plug connection
❑ for fuel system pressurisation pump - G6-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Ensure safe locking and check thatwiththe connector
respect is correctly
to the correctness locked
of information into place
in this document. by pulling
Copyright by ŠKODAitAUTO A. S.�

8 - Electrical plug connection

❑ for sender for fuel gauge display - G-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
9 - Fuel return line
❑ of engine
❑ pushed into the fuel tank
❑ do not kink
❑ to remove from connecting flange press release button on the connecting part
❑ observe the arrow direction (feed or return line) on the closing flange when installing
❑ Fit so that it can be heard clicking into place
❑ Press down again and check by pulling that the plug-in connector is fully engaged.
10 - Fuel gauge sender - G-
❑ Check resistance values ⇒ page 261
❑ removing and installing ⇒ page 223

2. Removing and installing parts of the fuel supply system 193

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.4 Fuel delivery unit, vehicles with four-wheel drive - Summary of components

1 - Fuel delivery unit

❑ Equipment variant with‐
out auxiliary heating
system
❑ with fuel pump for pre‐
delivery - G6-
❑ removing and installing
⇒ page 214
❑ electrical testing of the
fuel pump in Targeted
fault finding ⇒ Vehi‐
cle diagnostic tester
❑ Fill the vehicle with at
least 5 litres of fuel after
installing
❑ Fitting position
⇒ page 189
2 - Fuel delivery unit
❑ Equipment variant with
auxiliary heating system
❑ with fuel pump for pre‐
delivery - G6- Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ removing and installing with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
⇒ page 214
❑ electrical testing of the
fuel pump in Targeted
fault finding ⇒ Vehi‐
cle diagnostic tester
❑ Fill the vehicle with at
least 5 litres of fuel after
installing
❑ after installing a new
fuel delivery unit it will be
necessary to unscrew
the screw plug from the
connection on the fuel delivery unit in order to connect the fuel line of the auxiliary heating
❑ Observe the fitting position of the fuel discharge line for auxiliary heating ⇒ Heating, Air Conditioning;
Rep. gr. 82
❑ Fitting position ⇒ page 189
3 - Fuel gauge sender - G-
❑ check ⇒ Vehicle diagnostic tester
❑ removing and installing ⇒ page 223
4 - Sealing ring
❑ replace if damaged
❑ install when dry
5 - Lock ring, 110 Nm
❑ loosen and/or tighten using wrench - T30101 (3087)-

Note

Ensure that the fuel delivery unit is

not damaged when loosening and
tightening the lock ring of the holder
on the flange.

194 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

6 - Fuel return-flow line

❑ of engine
❑ pushed into the fuel tank
❑ do not kink
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
❑ observe the arrow direction (feed or return line) on the closing flange when installing
❑ Fit so that it can be heard clicking into place
❑ Press down again and check by pulling that the plug-in connector is fully engaged.
7 - Fuel feed line
❑ to fuel filter
❑ pushed into the fuel tank
❑ do not kink
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
❑ observe the arrow direction (feed or return line) on the closing flange when installing
❑ Fit so that it can be heard clicking into place
❑ Press down again and check by pulling that the plug-in connector is fully engaged.
8 - Fuel line
❑ for vehicles with auxiliary heating
❑ for the dosing pump of the auxilary heating
❑ Observe the fitting position of the fuel discharge line for auxiliary heating ⇒ Heating, Air Conditioning;
Rep. gr. 82
9 - Fuel pump control unit - J538-
❑ check in Targeted fault finding ⇒ Vehicle diagnostic tester
❑ removing and installing ⇒ page 240
10 - Electrical plug connection
❑ For fuel pump control unit - J538-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
11 - Electrical plug connection
❑ for fuel system pressurisation pump - G6-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
12 - Electrical plug connection
❑ for sender for fuel gauge display - G-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
13 - Electrical plug connection
❑ for Fuel gauge sender 2 - G169-
❑ Ensure safe locking and check that the connector is correctly locked into place by pulling it
14 - Lock ring, 110 Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ toloosen
with respect and/or
the correctness tighteninusing
of information wrench
this document. - T30101
Copyright by ŠKODA (3087)-
AUTO A. S.�

Note

When loosening and tightening the

lock ring of the holder on the flange
fuel gauge sender 2 - G169- is not
damaged when loosening and tight‐
ening the lock ring.

15 - Sealing ring
❑ replace if damaged
❑ install when dry

2. Removing and installing parts of the fuel supply system 195

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

16 - Fuel gauge sender 2 - G169-

❑ check ⇒ Vehicle diagnostic tester
❑ removing and installing ⇒ page 223
17 - Suction spray pump
❑ check ⇒ page 242
❑ removing and installing ⇒ page 242

2.5 Fuel filter - Summary of components

1 - Fuel filter - bottom part with

integrated bracket
❑ removing and installing
⇒ page 197
❑ Observe the instruc‐
tions for fuel hoses in
the engine compart‐
ment ⇒ page 200
2 - Fuel filter element
❑ Pay attention to change
intervals:
♦ ⇒ Maintenance ; Booklet
Octavia III
3 - Fuel filter - top part
❑ with connections
❑ removing and installing
⇒ page 197
❑ Observe the instruc‐
tions for fuel hoses in
the engine compart‐
ment ⇒ page 200
4 - 5 Nm
❑ Qty. 5
5 - Drain valve
❑ not fitted to all versions
❑ drain ⇒ page 197
6 - Hose clamps
❑ loosen with hose clip pli‐
ers - V.A.G 1921-
7 - Fuel intake hose
❑ to high Protected
pressure pumpCopying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Observe with therespect
instruc‐
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
tions for fuel hoses in the engine compartment ⇒ page 200
8 - Fuel return-flow hose
❑ of engine
❑ Observe the instructions for fuel hoses in the engine compartment ⇒ page 200
9 - Fuel intake hose
❑ from fuel tank
❑ Observe the instructions for fuel hoses in the engine compartment ⇒ page 200
❑ Unlock the quick coupling and disconnect ⇒ page 226 .

196 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 - Fuel return-flow hose

❑ Risk of damage to the fuel tank high pressure pump
❑ Observe the instructions for fuel hoses in the engine compartment ⇒ page 200
❑ Unlock the quick coupling and disconnect ⇒ page 226 .
11 - 8 Nm
❑ Qty. 2
12 - 8 Nm

2.6 Drain fuel filter

Special tools and workshop equipment required
♦ Fuel-resistant container
♦ Transparent hose

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .
♦ Make sure no diesel fuel runs onto the coolant hoses. If nec‐
essary clean the hoses immediately!
♦ Observe the disposal instructions!
♦ The drain valve is not present in all versions.

– Insert the transparent hose with a drain container onto the

drain plug -1-.
– Start engine.
– Carefully undo the drain plug -1- by 1/4 turns.

– Drain off approx. 0.3 to 0.4 litres of fluid. Once clean diesel fuel
discharges, seal the drain plug -1-.
– Switch off engine and remove the hose.

2.7 Removing and installing fuel filter

Special tools and workshop equipment required
♦ Hose clip pliers - V.A.G 1921-
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Observe rules for cleanliness ⇒ page 6 .
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Observe the instructions for the fuel hose in the engine com‐
partment ⇒ page 200 .

– Switch off ignition.

2. Removing and installing parts of the fuel supply system 197

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

If the fuel filter has to be removed because of lack of space only:

– Remove fuel hoses -1- and -2-. Unlock the quick coupling and
disconnect ⇒ page 226 .
– Push fuel lines -1- and -2- out of the holder -arrow- at the cool‐
ant expansion tank -3-.

– Unscrew securing bolts -2-.

– Unscrew nut -1-.

– Open holder -arrow- and push out fuel lines -1-.

– Equipment variant with water level sender - G120- : Discon‐

nect the electrical plug connection at the water level sender
-1-.
– Then lay the fuel filter to the side.
If the fuel filter must be opened:

198 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -1- to -5- -arrows- in the order shown.

– Collect any leaking fuel.
– Remove fuel filter top part -1- from fuel filter housing -2-.
– Lay fuel filter top part -1- to the side with the fuel lines con‐
nected.
If the fuel filter must be replaced:

– Pull off fuel hoses -3- to -5-.

– To do so, loosen hose clamps with pliers for spring strap clips.
– Release screws -2-.
– Unscrew nut -1-.

– Equipment variant with water level sender - G120- : Discon‐

nect the electrical plug connection at the water level sender
-1-.
– Remove fuel filter.
– Collect any leaking fuel.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Observe the instructions for the fuel hose in the engine com‐
partment ⇒ page 200 .
♦ Secure all hose connections with specified clamps ⇒ ETKA -
Electronic Catalogue of Original Parts .

– Filling and bleeding the fuel system ⇒ page 293 .

♦ Tightening torques
⇒ “2.5 Fuel filter - Summary of components”, page 196

2. Removing and installing parts of the fuel supply system 199

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.8 Fuel hoses in the engine compartment

Note

♦ Fuel hose supports at fuel filter -1-, at fuel temperature sender

-2- and push-on couplings are equipped with twin shaft profile
-arrows- and edge.
♦ In this way, the tightness of the fuel system is improved.
♦ The ultra-thin barrier layer on the inside of the fuel hoses will
be damaged when the fuel hoses are removed.
♦ This damage is not visible to the eye.
♦ After a time it leads to fuel system leakage.
♦ If the fuel filter must only be removed for space reasons, leave
fuel hoses on the fuel filter and high pressure pump if possible.
Lay fuel filter with connected hoses on the engine to avoid any
unnecessary replacement of hoses.
♦ For disconnection, use other fuel system connection points in
the engine compartment ⇒ page 197 .
♦ Unlock the quick coupling and disconnect ⇒ page 226 .

Caution

After fuel hoses are removed from the nozzle with twin shaft
profile and biting edge, these fuel hoses must be replaced.

If a fuel hose cannot be disconnected

by ŠKODA AUTOfrom the hoseAUTO nozzle
A. S. does by
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised A. S. ŠKODA not guarantee or accept any liability
hand: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Caution

Never push a screwdriver or a similar tool between the hose

and the hose nozzle!
Risk of damage to hose nozzle - the component must be re‐
placed.

– Turn fuel hose with suitable pliers and remove it.

If a fuel hose still cannot be disconnected from the hose nozzle:
– Cut into the hose only as far as the textile layer of the hose
lengthwise and detach the hose.
• Do not cut through the inner rubber layer. If the nozzle is dam‐
aged, it is necessary to replace the complete component.

Note

♦ Before fitting the new fuel hose, thoroughly clean the hose
nozzle from grease, oil and dirt. To do so, do not use any metal
tools that could damage the hose nozzle.
♦ Fit the fuel hose on the nozzle without lubricant and secure
with spring strap clamp.

200 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.9 Extract fuel from the fuel tank

⇒ “2.9.1 Emptying fuel tank when fuel pump is intact”,
page 201
⇒ “2.9.2 Emptying fuel tank if it is more than 3/4 full”, page 202
⇒ “2.9.3 Empty the fuel tank if less than 3/4 full, vehicles with front-
wheel drive”, page 203
⇒ “2.9.4 Empty the fuel tank if less than 3/4 full, vehicles with four-
wheel drive”, page 206

2.9.1 Emptying fuel tank when fuel pump is

intact
Special tools and workshop equipment required
♦ Fuel extraction device , e. g. -VAS 5190-
♦ Adapter for fuel extraction - VAS 5190 /2-

Note

If the fuel extraction device - VAS 5190- is still fitted with an ex‐
traction hose with a fixed tip, replace it by the version with a screw-
type tip.

– Unscrew tip -1- from extraction hose of fuel extraction unit -

VAS 5190- .
– Screw fuel extraction adapter - VAS 5190 /2- from fuel extrac‐
tion adapter set - VAS 5190 /10- onto extraction hose.
Carry out the following work procedure:
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Switch off ignition.

– Pull out the supply line -1- and catch the fuel that flows out with
a cleaning cloth. Unlock the quick coupling and disconnect
⇒ page 226 .

2. Removing and installing parts of the fuel supply system 201

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect the fuel extraction device - VAS 5190- with the adapt‐
er for the fuel extraction - VAS 5190 /3- to the fuel feed line.
– Connect ⇒ Vehicle diagnostic tester.
– Perform Targeted Functions empty fuel tank .
– Repeat the operation if necessary.

Note

The fuel pump is now activated.

– Open shut-off valve at the fuel extraction device - VAS 5190-

until the fuel tank is empty.

2.9.2 Emptying fuel tank if it is more than 3/4

full
Special tools and workshop equipment required
♦ Fuel extraction device , e. g. -VAS 5190-

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– In Protected
distance -a- from the end of the extraction hose make a
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
marking -arrow-
unless authorised on the
by ŠKODA hose.
AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Use insulating tape for this purpose.

Rear axle Distance a in mm

Vehicles with multi-control arm rear axle 945 mm
Vehicles with torsion beam rear axle 1010 mm

202 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open tank flap unit -2-.

– Clean the area around the fuel filler neck.
– Unscrew the cap -1- for the fuel filler neck.
– Remove the misfuelling protection device if present
⇒ page 219 .

Caution

Secure the earth cable of the fuel extraction device to a bare

metal part of the body.

– Push the extraction hose of the fuel extraction device as far

into the fuel tank holder as necessary until the previously ap‐
plied marking -arrow- terminates with the filler neck -2-.
– Drain the fuel tank through the filler neck as much as possible.

Note

♦ In the fuel tank there is a flap -1- on the lower end of the filler
neck, which must not be damaged by the extraction hose of
the fuel extraction device . Therefore, the hose must only be
pushed in up to the previously made marking -arrow-.
♦ If the extraction hose becomes stuck to the check valve while
being pulled out, do not pull the extraction hose violently.
♦ If this is the case, remove the fuel delivery unit and hold the
check valve open by hand. Make sure that your arm does not
come in contact with fuel.

– Carefully pull out the extraction hose.

Note

♦ When no more fuel is extracted, the tank is emptied just

enough for the sender flange to be opened without danger.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ When working on the fuel delivery unit or on
unless authorised the sender
by ŠKODA forŠKODA
AUTO A. S. fuel AUTO A. S. does not guarantee or accept any liability
gauge display , proceed as follows ⇒ page 203 .
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2.9.3 Empty the fuel tank if less than 3/4 full,

vehicles with front-wheel drive
Special tools and workshop equipment required
♦ Fuel extraction device , e. g. -VAS 5190-
♦ Wrench for union nut - T30101 (3087)-
♦ Disassembly wedge - 3409-

WARNING

To prevent large quantities of fuel from leaking when removing

the fuel delivery unit, the fuel tank must not be filled to more
than a maximum of 1/3.

2. Removing and installing parts of the fuel supply system 203

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

– Unclip cover -1- for the right closing flange with the disassem‐
bly wedge - 3409- on the retaining tabs -arrows-.

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -1- and -2- on the closing

flange and remove them.
Vehicles fitted with auxiliary heating
– Unhook plug connection -3- for the dosing pump - V54- from
the closing flange.
– Unlock plug connection -3- for the dosing pump - V54- and
remove it.

204 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Continued for all vehicles

– Push up catch -2- in -arrow direction A-.
– To do so, reach between bottom plate and fuel tank with a
finger.
– At the same time, carefully pull the fuel pump control unit -
J538- -1- carefully at the electrical wiring loom -3- out of the
uptake in -arrow direction B-.
– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Put fuel pump control unit - J538- to one side together with the
electrical wiring harness.

– Disconnect fuel line -1- at the closing flange. Unlock the quick
coupling and disconnect ⇒ page 226 .
– Disconnect fuel return line -2- at the closing flange. Unlock the
quick coupling and disconnect ⇒ page 226 .
Vehicles fitted with auxiliary heating
– Remove fuel line -3- to the dosing pump - V54- for the auxiliary
heating at the closing flange.
– To do so, open the bottom clamp.
– Carefully pull out fuel line -3-.
Continued for all vehicles

Note

Ensure that the fuel delivery unit is not damaged when loosening
the lock ring of the holder on the flange.

– Open locking ring using union nut wrench - T30101 (3087)- .

2. Removing and installing parts of the fuel supply system 205

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Carefully lift out fuel delivery unit flange -3-.

– Remove gasket -1- and raise the fuel delivery unit flange
slightly higher.

Caution

Secure the earth cable of the fuel extraction device to a bare

metal part of the body.

– Insert suction hose of fuel extractor - VAS 5190- as far as

possible into fuel tank.
– Extract fuel using the fuel extraction device - VAS 5190- .
If fuel tank needs only to be emptied, re-install the fuel delivery
unit ⇒ page 210 .
Tightening torques
♦ Fuel delivery unit, vehicles with front-wheel drive - Summary
of components ⇒ page 192
♦ ⇒ Heating, Air conditioning; Rep. gr. 82

2.9.4 Empty the fuel tank if less than 3/4 full,

vehicles with four-wheel drive
Special tools and workshop equipment required
♦ Fuel extraction device , e. g. -VAS 5190-
♦ Wrench for union nut - T30101 (3087)-
♦ Disassembly wedge - 3409-

WARNING

To prevent large quantities of fuel from leaking when removing

the fuel delivery unit, the fuel tank must not be filled to more
than a maximum of 1/3.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

206 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- for the right closing flange with the disassem‐
bly wedge - 3409- on the retaining tabs -arrows-.

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -1- and -2- on the closing

Continued for all vehicles

– Push up catch -2- in -arrow direction A-.
– To do so, reach between bottom plate and fuel tank with a
finger. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– At the same time, carefully
with respectpull
to thethe fuel pump
correctness control
of information in thisunit - Copyright by ŠKODA AUTO A. S.�
document.
J538- -1- carefully at the electrical wiring loom -3- out of the
uptake in -arrow direction B-.
– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Put fuel pump control unit - J538- to one side together with the
electrical wiring harness.

2. Removing and installing parts of the fuel supply system 207

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

Ensure that the fuel delivery unit is not damaged when loosening
the lock ring of the holder on the flange.

– Open locking ring using union nut wrench - T30101 (3087)- .

– Carefully lift out fuel delivery unit flange -3-.

– Remove gasket -1- and raise the fuel delivery unit flange
slightly higher.

Caution

Secure the earth cable of the fuel extraction device to a bare

metal part of the body.

– Insert suction hose of fuel extractor - VAS 5190- as far as

possible into fuel tank.
– Extract fuel using the fuel extraction device - VAS 5190- .

208 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- at retaining tabs -arrows-, using removal

wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -2- from left closing flange,

and remove.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Unlock electrical plug connections -1-authorised
unless and -3-byfrom ŠKODA closing
AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
flange, and disconnect. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unclip electrical plug connections -1- and -3- from the uptakes
on the closing flange.

Note

Ensure that the fuel delivery unit is not damaged when loosening
and tightening the lock ring of the holder on the flange.

– Open lock ring with the wrench - T30101 (3087)- .

2. Removing and installing parts of the fuel supply system 209

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Carefully remove the closing flange -2- on the left together with
the suction jet pump -1- from the fuel tank opening a little.
– Insert suction hose of fuel extractor - VAS 5190- as far as
possible into fuel tank.
– Extract fuel using the fuel extraction device - VAS 5190- .
When only emptying the fuel tank:
– Reinstall the fuel delivery unit ⇒ page 214 .
– Install the fuel gauge sender 2 - G169- again ⇒ page 223 .
Tightening torques
♦ Fuel delivery unit, vehicles with four-wheel drive - Summary of
components ⇒ page 194
♦ ⇒ Heating, Air conditioning; Rep. gr. 82

2.10 Removing and installing the fuel delivery

unit, vehicles with front-wheel drive
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Key - T30101 (3087)-
Precondition
• The fuel tank must not be more than 1/3 full.
Removing

Note

♦ If necessary drain the fuel tank ⇒ page 201 .

♦ Safety precautions when working on the fuel supply system
⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Move front seats all the way forward.

– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- for the right closing flange with the disassem‐
bly wedge - 3409- on the retaining tabs -arrows-.

210 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock plug connections -1, 2- on closing flange to unlock the

connector lock.
Vehicles fitted with auxiliary heating
– Unhook the electrical plug connection -3- for dosing pump of
the auxiliary heating - V54- on the closing flange.
– Unlock the connector -3- for dosing pump of the auxiliary heat‐
ing - V54- and remove.
Continued for all vehicles

– Push up fixing catch -2- with a finger between the bottom plate
and the fuel tank-arrow A-.
– Simultaneously pull the fuel pump control unit - J538- -1- at
the electric wiring loom -3- carefully out of the uptake
-arrow B-.
– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Expose the fuel pump control unit - J538- together with the
electrical wiring harness.

– Remove fuel return line -1, 2- from the closing flange. Unlock
the quick coupling and disconnect ⇒ page 226 .
Vehicles fitted with auxiliary heating
– Loosen hose clamp, fuel line -3- to the dosing pump for the
auxiliary heating from the closing flange.
Continued for all vehicles

Note

Ensure that the fuel delivery unit is not damaged when loosening
the lock ring of the holder on the flange.

2. Removing and installing parts of the fuel supply system 211

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open lock ring with the wrench - T30101 (3087)- .

– Pull sealing flange -3- slightly out of the fuel tank opening.
– Remove sealing ring -1- from fuel tank opening.
– Pull sealing flange -2- carefully out of the fuel tank opening.

WARNING

There is a risk of fuel flowing out of the fuel delivery unit which
is still full.
♦ Put cleaning cloth underneath to collect fuel.

– Pull fuel delivery unit with sender for fuel gauge display - G-
carefully out of the fuel tank opening, turning and tilting as
appropriate.

Note

When removing the fuel delivery unit, ensure that the float arm of
the fuel gauge sender - G- is not bent.

Note

♦ The old delivery unit must be emptied before disposing of it if

it should be replaced.
♦ You must be compliance with the environmental regulations
when disposing of it.
♦ Check fuel tank for contaminations.

Install
Installation is carried out in the reverse order. Pay attention to the
following:

NoteProtected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Note the fitting position of all parts.
♦ Replace damaged gasket ring.
♦ When inserting the fuel delivery unit, ensure that the float arm
of the fuel gauge sender - G- is not bent.

212 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Install new seal -1- for closing flange while dry.

– Coat inner side of gasket ring -1- with fuel.
– Insert fuel delivery unit with sender for fuel gauge display - G-
carefully through the fuel tank opening.
– Press down the closing flange against the spring force and
bring it into the installation position.

– The peg -2- at the closing flange -1- must be located against
-arrow 3- at the fuel tank.

Caution

Risk of leakage.
♦ The gasket ring must not get damaged or squashed when
inserting the sealing flange.

Note

Ensure that the fuel delivery unit is not damaged when tightening
the lock ring of the holder on the flange.

– Insert lock ring and tighten using the wrench - T30101 (3087)- .

– Fit fuel lines -1- andProtected

-2- sobythat they can be heard clicking into
place.
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– If present, install the fuel line -3- for the dosing pump of the
auxiliary heating - V54- at the closing flange ⇒ Heating, Air
Conditioning; Rep. gr. 82 .
– Press fuel lines down again and check by pulling that the plug-
in connector is fully engaged.

2. Removing and installing parts of the fuel supply system 213

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect connectors -1- and -2-.

– If present, unhook the electrical plug connection -3- for dosing
pump of the auxiliary heating - V54- on the closing flange.
– Check the connector for firm seating by pulling in the opposite
direction!
– After installing the fuel delivery unit, refuel the vehicle with at
least 5 litres of fuel.
Tightening torques
♦ Fuel delivery unit, vehicles with front-wheel drive - Summary
of components ⇒ page 192 .

2.11 Removing and installing the fuel delivery

unit, vehicles with four-wheel drive
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Key - T30101 (3087)-
Precondition
• The fuel tank must not be more than 1/3 full.
Removing

Note

♦ If necessary drain the fuel tank ⇒ page 201 .

♦ Safety precautions when working on the fuel supply system
⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Move front seats all the way forward.

– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- for the right closing flange with the disassem‐
bly wedge Protected
- 3409-by on the retaining
copyright. tabsor-arrows-.
Copying for private commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

214 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock plug connections -1, 2- on closing flange to unlock the

connector lock.
Vehicles fitted with auxiliary heating
– Unhook the electrical plug connection -3- for dosing pump of
the auxilary heating - V54- on the closing flange.
– Unlock the connector -3- for dosing pump of the auxiliary heat‐
ing - V54- and remove.
Continued for all vehicles

– Remove fuel return line -1, 2- from the closing flange. Unlock
the quick coupling and disconnect ⇒ page 226 .
Vehicles fitted with auxiliary heating
– Loosen hose clamp, remove fuel line -3- to the dosing pump
for the auxiliary heating - V54- from the closing flange.
Continued for all vehicles

Note

Ensure that the fuel delivery unit is not damaged when loosening
the lock ring of the holder on the flange.

2. Removing and installing parts of the fuel supply system 215

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open lock ring with the wrench - T30101 (3087)- .

Vehicles without auxiliary heating system

– Pull sealing flange -3- slightly out of the fuel tank opening.
– Remove sealing ring -1- from fuel tank opening.
– Pull closing flange with fuel line -2- carefully out of the fuel tank
opening.

– Reach into the fuel tank through the opening, remove the drive
jet line -1-, while doing so, press the release at the connection.
Unlock the quick coupling and disconnect ⇒ page 226 .
– Remove the pressure line for suction jet pump from the fuel
delivery unit.
– Press the catches -2- and -3- and remove the line.

WARNING

There is a risk of fuel flowing out of the fuel delivery unit which
is still full.
♦ Put cleaning cloth underneath to collect fuel.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Pull fuel delivery unit with sender for fuel unless
gauge display - G-
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
carefully out of the fuel tank opening, turning and tilting as
appropriate.

Note

When removing the fuel delivery unit, ensure that the float arm of
the fuel gauge sender - G- is not bent.

Vehicles fitted with auxiliary heating

216 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Pull sealing flange -1- slightly out of the fuel tank opening.
– Remove sealing ring -2- from fuel tank opening.
– Pull closing flange with fuel line and electrical lines carefully
out of the fuel tank opening as far as possible.

Note

When removing the fuel delivery unit, ensure that you do not bend
the float arm of the sender for the fuel gauge display.

– Reach into the fuel tank through the opening, unlock the de‐
livery unit from the locking mechanisms -2 and 3- and remove
from the fuel delivery unit.

2. Removing and installing parts of the fuel supply system 217

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove and disconnect the drive jet line -1-; to do so, press
the release at the connection. Unlock the quick coupling and
disconnect ⇒ page 226 .
– Carefully remove the fuel lines -1- and -2- from the fuel tank
opening.

WARNING

There is a risk of fuel flowing out of the fuel delivery unit which
is still full.
♦ Put cleaning cloth underneath to collect fuel.

– Pull fuel delivery unit -3- with the fuel gauge sender - G- care‐
fully out of the fuel tank opening by turning and tilting as
appropriate.
Continued for all vehicles

Note

♦ The old delivery unit must be emptied before disposing of it if

it should be replaced.
♦ You must be compliance with the environmental regulations
when disposing of it.
♦ Check fuel tank for contaminations.

Install
Installation is carried out in the reverse order. Pay attention to the
following:

Note
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Note the fitting position of all parts.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Replace damaged gasket ring.

♦ When inserting the fuel delivery unit, ensure that the float arm
of the fuel gauge sender - G- is not bent.

– Install new seal -1- for closing flange while dry.

218 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– The peg -2- at the closing flange -1- must be located against
-arrow 3- at the fuel tank.

Caution

Risk of leakage.
♦ The gasket ring must not get damaged or squashed when
inserting the sealing flange.

Note

Ensure that the fuel delivery unit is not damaged when tightening
the lock ring of the holder on the flange.

– Insert lock ring and tighten using the wrench - T30101 (3087)- .

– Fit fuel lines -1- and -2- so that they can be heard clicking into
place.
– If present, install the fuel line -3- for the dosing pump of the
auxiliary heating - V54- at the closing flange ⇒ Heating, Air
Conditioning; Rep. gr. 82 .
– Press fuel lines down again and check by pulling that the plug-
in connector is fully engaged.

– Connect connectors -1- and -2-.

– If present, unhook the electrical plug connection -3- for dosing
pump of the auxiliary heating - V54- on the closing flange.
– Check the connector for firm seating by pulling in the opposite
direction!
– After installing the fuel delivery unit, refuel the vehicle with at
least 5 litres of fuel.
Tightening torques
♦ Fuel delivery unit, vehicles with four-wheel drive - Summary of
components ⇒ page 194 .

2.12 Removing and installing misfuelling pro‐

tection
Special tools and workshop equipment required

2. Removing and installing parts of the fuel supply system 219

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

♦ Circlip pliers
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Clean the area around the fuel filler neck.

– Unscrew the cap from the fuel filler neck.
– Unlock catch for lock ring with Torx screwdriver -arrow-.

– Insert circlip pliers into both lock ring openings -arrow-.

– Turn locking ring anticlockwise by approximately 25°.

220 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Tilt lock ring out of the fuel filler neck and remove through the
opening -arrows- for the cap.

– Pull misfuelling protection out of the fuel filler neck -arrow-, use
circlip pliers if necessary.
Install
Installation is carried out in the reverse order. Pay attention to the
following:

– Place misfuelling protection in the fuel filler neck.

• The peg at the misfuelling protection must reach into the
groove on the fuel filler neck -arrows-.

2. Removing and installing parts of the fuel supply system 221

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Install lock ring with circlip pliers - to do so, turn the locking ring
clockwise by 25°.

– When installation is correct the markings on the lock ring and

fuel filler neck must be opposite to each other -arrows-.

2.13 Deactivate misfuelling protection

Procedure
– Remove misfuelling protection ⇒ page 219 .
– Remove the catches marked in red at the marked positions
-arrows-.

Note

It must be possible to open misfuelling protection closing flap of

misfuelling without it becoming hooked.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Remove misfuelling protection ⇒ page 219 . unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

222 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.14 Removing and installing the sender for

fuel gauge display - G-
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove fuel delivery unit:

♦ Vehicles with front-wheel drive ⇒ page 210 .
♦ Vehicles with four-wheel drive ⇒ page 214 .
– Disconnect electrical plug connections -2- on the closing
flange, thereby unlocking the plug lock.
– Unhook the electric cable from the holder -arrows A - and ex‐
pose it.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Unlock catches
unless authorised-1-, -3- -arrows
by ŠKODA AUTO A. S.B- andAUTO
ŠKODA pushA. out the
S. does notsender
guarantee for
or accept any liability
fuel gauge display
with respect - G- upwards
to the correctness -arrow
of information in thisC-.
document. Copyright by ŠKODA AUTO A. S.�

Install
Installation is carried out in the reverse order. When installing,
note the following:
• Installation instructions
⇒ “2.3 Fuel delivery unit, vehicles with front-wheel drive - Sum‐
mary of components”, page 192
– Insert the sender for fuel gauge display - G- in the guides at
the fuel delivery unit and press downwards until it latches into
position.
– Check the connector for firm seating by pulling in the opposite
direction!
– Connect electric cables to fuel delivery unit and fit.
– Install fuel delivery unit ⇒ page 210 .

2.15 Removing and installing fuel gauge

sender 2 - G169-
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Wrench for union nut - T30101 (3087)-
• The fuel tank must not be more than 1/3 full.

Note

♦ If necessary drain the fuel tank ⇒ page 201 .

♦ Safety precautions when working on the fuel supply system
⇒ page 4 .
♦ Observe the regulations concerning cleanliness when working
on the fuel supply/injection system ⇒ page 6 .
♦ Make sure that the sender for fuel gauge display is not bent.

2. Removing and installing parts of the fuel supply system 223

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing
– Move front seats all the way forward.
– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- at retaining tabs -arrows-, using removal
wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -2- from left closing flange,

and remove.
– Unlock electrical plug connections -1- and -3- from closing
flange, and disconnect.
– Unclip electrical plug connections -1- and -3- from the uptakes
on the closing flange.

Note

Ensure that the fuel delivery unit is not damaged when loosening
and tightening the lock ring of the holder on the flange.

– Open lock ring with the wrench - T30101 (3087)- .

224 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Carefully raise closing flange -2- and remove it from the fuel
tank opening.

Note

Remove gasket ring -3- from fuel tank opening.

– Remove the suction jet pump -1- from the fuel gauge sender
2 - G169- . To do so, carefully bend the retaining lugs
-arrows- outwards.

WARNING

Place a cleaning cloth underneath in order to collect the fuel.

– Remove the fuel gauge sender 2 - G169- carefully out of the

fuel tank opening. Turn and tilt accordingly to do so.

Note

Make sure that the float arm of the fuel gauge sender 2 - G169-
is not bent.

– Unlock and detach the connector -3- at unit -2-.

– Thread out the electrical cables.
– Unlock the fuel gauge sender 2 - G169- -1- from the unit -2-.
To do so, carefully bend the guide lugs -arrows-.
– Detach the fuel gauge sender 2 - G169- in
-direction of arrow-.

♦ You must be compliance with the environmental regulations

when disposing of it.
♦ Check fuel tank for contaminations.

Install
Installation is carried out in the reverse order. Pay attention to the
following:

Note

♦ Note the fitting position of all parts.

♦ Replace damaged gasket ring.
♦ Correctly place the electrical lines into the uptakes.

– Check the fuel gauge sender 2 - G169- for firm seating by

pulling in the opposite direction.

2. Removing and installing parts of the fuel supply system 225

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Coat inner side of gasket ring -3- with fuel.

– Install the suction jet pump -1-.

Note

When inserting the fuel delivery unit 2 - G169- , ensure that the
float arm of the fuel gauge sender is not bent.

– Press the closing flange against the spring force and bring it
into the installation position.

– Arrow -3- at the fuel tank must point to marking -2- on the
closing flange -1-.

WARNING

Risk of leakage.
♦ The gasket ring must not get damaged or squashed when
inserting the sealing flange.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Note

Ensure that the fuel delivery unit is not damaged when tightening
the lock ring of the holder on the flange.

– Tighten the lock ring with socket wrench - T30101 (3087)- .

– Check the connector for firm seating by pulling in the opposite
direction!
Tightening torques
♦ Fuel delivery unit, vehicles with four-wheel drive - Summary of
components ⇒ page 194 .

2.16 Separating push-on couplings

Special tools and workshop equipment required
♦ Lever - T10468-

226 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Assign quick couplings

Note

♦ Quick couplings of fuel, vacuum and ventilation lines are col‐

our marked. Either the colour point at the quick coupling or the
release button has the corresponding colour.
♦ The push-fit couplings must »audibly« click in place when se‐
curing it.
♦ Check the quick couplings for firm seating by pulling in the
opposite direction!

Push-on coupling Colour code on connector

Fuel feed line Black
Fuel return line Blue
Bleeding White, beige
Vacuum Green

WARNING

Fuel supply line is pressurised. Wear safety goggles and safety

clothing, in order to avoid Protected
injuriesby and skin
copyright. contact
Copying with
for private fuel. purposes, in part or in whole, is not permitted
or commercial
Place cleaning cloths around the connection point before de‐
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
taching hose connections. Reduce pressure by carefully re‐
moving the hose.

Variant 1

Note

When the push-fit coupling is fitted with a plastic circlip, leave it

inserted when removing and installing the quick release.

Quick coupling with release buttons -arrows- on right and left.

Opening

2. Removing and installing parts of the fuel supply system 227

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

The separation point -1- in the engine compartment must be held.

– Insert the lever - T10468- between the heat shield and the stop
-arrow- of the fuel feed line -2- and hold it.
Continued for all separation points

– Push push-on coupling -1- in -direction of arrow A-.

– Press the release buttons and detach the quick coupling -1- in
-direction of arrow B- from the fuel flow line -2-.
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 2

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Quick coupling with pull
with respect to the release
correctness -arrow-.
of information in this document. Copyright by ŠKODA AUTO A. S.�

Opening

228 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Push push-on coupling -1- in -direction of arrow A-.

– Pull pull-release mechanism -2- in -direction of arrow B-.
– Detach the quick coupling -1- in -direction of arrow B- from the
fuel flow line -3-.
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 3

Quick coupling with front release button -arrow-.

Opening
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Press release
unless authorisedbutton -arrow-
by ŠKODA AUTO A. and pullAUTO
S. ŠKODA push-on connectors
A. S. does off.
not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 4

Quick coupling with release buttons -arrows- on right and left.

Opening
– Press push-on coupling in -direction of arrow A-.
– Press release buttons -arrows- and pull push-on coupling off.
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 5

Quick coupling with release buttons -arrows- on right and left.

Opening
– Press release buttons -arrows- and pull push-on coupling off.
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 6

2. Removing and installing parts of the fuel supply system 229

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Quick coupling with release buttons -arrows- on right and left.

Opening
– Press push-on coupling -1- in -direction of arrow- and hold
pressed.
– Press release buttons -arrows- and pull push-on coupling off.
Pay attention to the colour assignment when installing
⇒ page 227 .
– Check the quick couplings for firm seating by pulling in the
opposite direction!
Variant 7

Quick coupling -1- with release buttons -2- right and left.
Opening
– Press push-on coupling -1- in -arrow direction A- and hold
pressed.
– Press release buttons -2- in -arrow direction B- and remove
quick coupling- 1-.
Pay attention to the colour assignment when installing
⇒ page 227 .
The quick coupling must be heard to click into place.
– Check the quick couplings for firm seating by pulling in the
opposite direction!

2.17 Removing and installing the fuel delivery

unit, vehicles with front-wheel drive
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Engine and gearbox jack , e.g. -V.A.G 1383 A-
Removing

Note

♦ Drain the fuel tank ⇒ page 201 .

♦ Safety precautions when working on the fuel supply system
⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Move front seats all the way forward.

– Switch off ignition and pull out ignition key.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

230 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- at retaining tabs -arrows-, using removal

wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock plug connections -1, 2- on closing flange to unlock the

connector lock.
– If present, disconnect electrical plug connection -3- for auxili‐
ary heating dosing pump - V54- , thereby unlocking the con‐
nector lock. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2. Removing and installing parts of the fuel supply system 231

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Push up fixing catch -2- with a finger between the bottom plate
and the fuel tank-arrow A-.
– Simultaneously pull the fuel pump control unit - J538-
-Pos. 1- at the electric wiring loom -3- carefully out of the
uptake -arrow B-.
– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Clean the area around the fuel filler neck.
– Unscrew the cap from the fuel filler neck.

Note

Close the opening of the fuel filler neck with a clean cloth so that
no dirt can penetrate.

– Remove tank flap unit ⇒ Body Work; Rep. gr. 55 .

– Unscrew right rear wheel ⇒ Chassis; Rep. gr. 44 .
– Remove the rear right wheelhouse liner ⇒ Body Work; Rep.
gr. 66 .
Vehicles with torsion beam axle
– Remove the rear wheel brake calliper and store to on side ⇒
Suspension; Rep. gr. 46 .
– Disconnect the plug connection from the ABS speed sensor,
right rear wheel, and undo the line from the mounting brackets
at the rear axle ⇒ Suspension; Rep. gr. 45 .
Continued for all vehicles

– Unscrew screws -1, 2- for fuel filler neck.

– Remove the rear silencer:
♦ For vehicles with engine identification characters CLHA,
CLHB, CKFB, CKFC, CRVC ⇒ page 351 .
♦ For vehicles with engine identification characters CUPA
⇒ page 353 .

232 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove auxiliary heating fuel line -1-. Unlock the quick cou‐
pling and disconnect ⇒ page 226 .
Vehicles with multi-link suspension
– Mark movement direction on the tensioning strap.

– Release screw -4-.

– Remove suspension/exhaust system.
– Unscrew screw -2- and remove tensioning strap.

– As shown in the illustration, place the engine and gearbox jack

- V.A.G 1383 A- under the vehicle for support purposes and
support the fuel tank.

2. Removing and installing parts of the fuel supply system 233

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -1- and -3-.

Note

♦ To provide a clearer illustration, the fuel tank is shown without

the engine and gearbox jack - V.A.G 1383 A- .
♦ The aid of a 2nd mechanic is required to remove the fuel tank.

– Lower fuel tank with engine and gearbox jack - V.A.G 1383
A- .
– Lower fuel tank by pivoting it in the side downwards.
– Pull the filler tube through between the rear axle and body‐
shell.
Vehicles with torsion beam axle
– Mark movement direction on the tensioning strap.

– Release screw -5-.

– Remove suspension/exhaust system -arrow-.
– Unscrew screws -3- and remove tensioning strap -7-.

– As shown in the illustration, place the engine and gearbox jack

- V.A.G 1383 A- under the vehicle for support purposes and
support the fuel tank -1-.

234
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Rep. gr.20 - Fuel supply system
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -2-, -4- and -6-.

Note

♦ To provide a clearer illustration, the fuel tank is shown without

the engine and gearbox jack - V.A.G 1383 A- .
♦ The aid of a 2nd mechanic is required to remove the fuel tank.

– Lower fuel tank with engine and gearbox jack - V.A.G 1383
A- .
– Lower fuel tank by pivoting it in the side downwards.
– Pull the filler tube through between the rear axle and body‐
shell.
Install
♦ Tightening torques, assembly instructions ⇒ page 185 .

Note

♦ Replace gasket rings.

♦ Ensure that catches are secure when connecting the electrical
plug connections.

– Check installation position of the vent end piece ⇒ page 185 .

– Check the earth strap for corrosion, remove any corrosion.

– Ensure the plug connection fits tightly:

• The plug -2- on the metal plate ring -3- must be pushed on
firmly.
• The contact peg -1- must be hung on the fuel tank -4- and
secured with the spacer bush -5-.

WARNING

Risk from electrostatic charge.

♦ After installing, use an ohmmeter to test the electrical con‐
nection of the threaded ring on the fuel filler neck at a bare
point on the body.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
• Specified valueunless
approximately 0 Ω. of information in this document. Copyright by ŠKODA AUTO A. S.�
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness

– Check that the fuel lines are clipped to the fuel tank.
– Position fuel tank with tensioning straps with the engine and
gearbox jack - V.A.G 1383 A- at the vehicle underside.
– When positioning the fuel tank, ensure that the fuel filler neck
is inserted correctly into the opening on the body.

Note

New screws for tensioning strap are longer than series screws,
note the part number⇒ ETKA - Electronic Catalogue of Original
Parts

Further installation occurs in reverse order.

2. Removing and installing parts of the fuel supply system 235

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.18 Removing and installing the fuel delivery

unit, vehicles with four-wheel drive
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Engine and gearbox jack , e.g. -V.A.G 1383 A-
Removing

Note

♦ Drain the fuel tank ⇒ page 201 .

♦ Safety precautions when working on the fuel supply system
⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Move front seats all the way forward.

– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover right -1- at retaining tabs -arrows-, using removal
wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

236 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock electrical plug connection -2- from closing flange, and

remove.
Vehicles fitted with auxiliary heating
– Unlock the electrical plug connection -3- for dosing pump -
V54- and disconnect.
Continued for all vehicles

– Unclip cover -1- at retaining tabs -arrows-, using removal

wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -2- from left closing flange,

and remove.
– Unlock electrical plug connections -1- and -3- from closing
flange, and disconnect.
– Unclip electrical plug connections -1- and -3- from the uptakes
on the closing flange.

2. Removing and installing parts of the fuel supply system 237

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open tank flap unit -2-.

– Clean the area around the fuel filler neck.
– Unscrew the cap -1- for the fuel filler neck.

Note

Close the opening of the fuel filler neck with a clean cloth so that
no dirt can penetrate.

– Remove tank flap unit ⇒ Body Work; Rep. gr. 55 .

– Remove right rear wheel ⇒ Chassis; Rep. gr. 44 .
– Remove the rear right wheelhouse liner ⇒ Body Work; Rep.
gr. 66 .

– Unscrew screws -1- -2- for fuel filler neck.

– Remove the rear silencer ⇒ page 354 .

– Detach the fuel feed line -1- and the fuel return-flow line -2-.
Unlock the quick coupling and disconnect ⇒ page 226 .
Vehicles fitted with auxiliary heating

– Remove auxiliary heating fuel line -1-. Unlock the quick cou‐
pling and disconnect ⇒ page 226 .
Continued for all vehicles
– Remove propshaft ⇒ Gearbox; Rep. gr. 39 .

238 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock the electrical plug connection -1- for Haldex coupling

and disconnect.

– As shown in the illustration, place the engine and gearbox jack

- V.A.G 1383 A- under the vehicle for support purposes and
support the fuel tank.

– Unscrew the screws -1- to -5-.

Note

♦ To provide a clearer illustration, the fuelProtected

tank isbyshown without
the engine and gearbox jack - V.A.G 1383
unless A- . copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ The aid of a 2nd mechanic is required to remove the fuel tank.

– The second mechanic must support the fuel tank at the rear
edge with one hand.
– Lower fuel tank with engine and gearbox jack - V.A.G 1383
A- .
– Lower fuel tank by pivoting it in the side downwards.
– Pull the filler tube through between the rear axle and body‐
shell.
– The second mechanic must support the fuel filler neck at the
longitudinal swing arm with one hand.
Install

2. Removing and installing parts of the fuel supply system 239

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Install in the reverse order of removal. When doing this, note the
following:
Observe the fitting position of the ventilation end piece -1- at the
fuel tank -2-.
• Angle -α- must be 60°.
– Lay the vent and fuel hoses without any kinks.
– Make sure the stop buffer -Pos. 6- is seated correctly
⇒ page 189 .
– Pull the filler tube through between the rear axle and body‐
shell.
– If present, check the dosing pump - V54- for firm seating.
– Make sure the fuel filler neck correctly engages in the opening
in the bodyshell.
– Position fuel tank with tensioning strap with the engine and
gearbox jack - V.A.G 1383 A- at the underbody.
– Pay attention to correct fit of the mounting bracket for the ex‐
haust system ⇒ page 347 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Pay attention to the position of the tensioning strap. by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
unless authorised
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Make sure the line connections fit tightly.
– Check that the fuel lines are clipped to the fuel tank.
– Take fitting position of earth connection into account.
– Check the earth strap for corrosion, remove any corrosion.

• The plug -2- on the metal plate ring -3- must be pushed on
firmly.
• The contact peg -1- must be hung on the fuel tank -4- and
secured with the spacer bush -5-.

WARNING

Risk from electrostatic charge.

♦ After installing, use an ohmmeter to test the electrical con‐
nection of the plate ring on the fuel filler neck at a bare
point on the body.
• Specified value approximately 0 Ω.

♦ Tightening torques, assembly instructions ⇒ page 189 .

2.19 Removing and installing fuel pump con‐

trol unit - J538-
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
Removing
– Move front seats all the way forward.
– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

240 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- for closing flange using the disassembly

wedge - 3409- from the uptake -arrows-.

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Push up fixing catch -2- with a finger between the bottom plate
and the fuel tank-arrow A-.
– Simultaneously pull the fuel pump control unit -byJ538-
Protected copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
-Pos. 1- at the electric wiring loom -3- carefully out of
unless authorised the AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
by ŠKODA
uptake -arrow B-. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Remove electrical plug connection and fuel pump control unit
- J538- .
Install
Installation is carried out in the reverse order. Pay attention to the
following:
– Connect the electrical wiring harness to the fuel pump control
unit - J538- .
– Check the connector for firm seating by pulling in the opposite
direction!
– Push fuel pump control unit - J538- into the uptake and push
in until there is an audible click.
– Check the fuel pump control unit - J538- for firm seating by
pulling in the opposite direction.

2. Removing and installing parts of the fuel supply system 241

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.20 Check the suction jet pump

The fuel tank consists of a left and right chamber. In order to pump
the fuel out of the left chamber -3- of the fuel tank into the right
chamber to the housing of the fuel delivery unit -2-, a suction jet
pump -1- is required.
Function of the suction jet pump
Suction jet pump functions according to a basic physical principle:
Drive jet from the electric fuel pump is pushed through the nozzle
in the suction jet pump and is thus accelerating. This acceleration
causes the take-up of the surrounding fuel and the latching to the
delivery chamber of the fuel delivery unit.
Fault caused by faulty ejector pump

Caution

Vehicle breakdown due to faulty suction jet pump.

In the event of a fault to the suction jet pump, the vehicle may
brake down due to a lack of fuel even if the fuel tank is up to
1/ full.
4

If the suction jet pump fails to work, up to 15 l of fuel (up to approx.

1/ content of the tank) will remain in the left-hand area of the fuel
4
tank from where the fuel delivery unit is not draw fuel.
If the vehicle remains broken down due to a lack of fuel with a fuel
tank up to approx. 1/4 full, proceed as follows:
– Check the fuel pump with Targeted fault finding ⇒ Ve‐
hicle diagnostic tester
When the fuel pump is OK and the fuel is not drawn in:
– Add around 5 litres of fuel.
– Start engine.
if the engine starts up:
– Replace the suction jet pump ⇒ page 242 .

2.21 Removing and installing suction jet

pump
Special tools and workshop equipment required
♦ Disassembly wedge - 3409-
♦ Wrench for union nut - T30101 (3087)-
• The fuel tank must not be more than 1/3 full.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Note unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ If necessary drain the fuel tank ⇒ page 201 .

242 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing
– Switch off ignition and pull out ignition key.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- for the right closing flange with the disassem‐
bly wedge - 3409- on the retaining tabs -arrows-.

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Disconnect the electrical plug connections -1 and 2- from clos‐

ing flange.
Vehicles fitted with auxiliary heating
– Unhook the electrical plug connection -3- for dosing pump -
V54- on the closing flange.
– Unlock plug connection -3- for the dosing pump - V54- and
remove it.
Continued for all vehicles

– Push up catch -2- in -arrow direction A- - to do so, reach be‐

tween bottom plate and fuel tank with a finger..
– At the same time, carefully pull the fuel pump control unit -
J538- -1- carefully at the electrical wiring loom -3- out of the
uptake in -arrow direction B-.
– Take out fuel pump control unit - J538- inwards between fuel
tank and bottom plate.
– Expose the fuel pump control unit - J538- together with the
electrical wiring harness.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

2. Removing and installing parts of the fuel supply system 243

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove the fuel lines -1, 2- from the closing flange, to do so

press the release button. Unlock the quick coupling and dis‐
connect ⇒ page 226 .
Vehicles fitted with auxiliary heating
– Remove fuel line -3- to the dosing pump - V54- for the auxiliary
heating at the closing flange.
– To do so, open the bottom clamp.
– Carefully pull out fuel line -3-.
Continued for all vehicles

Note

Ensure that the fuel delivery unit is not damaged when loosening
and tightening the lock ring of the holder on the flange.

– Open lock ring with the wrench - T30101 (3087)- .

Vehicles without auxiliary heating system

– Lift the closing flange -3- carefully out of the fuel tank opening.
– Remove sealing ring -1- from fuel tank opening.
– Pull closing flange with fuel line -2- carefully out of the fuel tank
opening.

Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
When removing the fuel delivery unit, ensure that you do not bend
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

the float arm of the sender for the fuel gauge display.

244 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Reach into the fuel tank through the opening, remove the drive
jet line -1-, while doing so, press the release at the connection.
Unlock the quick coupling and disconnect ⇒ page 226 .
– Remove the pressure line for the suction jet pump from the
fuel delivery unit, to do so press catches -2- and -3- and re‐
move the cable.
Vehicles fitted with auxiliary heating

Note

When removing the fuel delivery unit, ensure that you do not bend
the float arm of the sender for the fuel gauge display.

– Reach into the fuel tank through the opening, unlock the de‐
livery unit from the locking mechanisms -2 and 3- and remove
from the fuel delivery unit.

– Remove and disconnect the drive jet line -1-; to do so, press
the release at the connection. Unlock the quick coupling and
disconnect ⇒ page 226 .
Continued for all vehicles

2. Removing and installing parts of the fuel supply system 245

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- for left closing flange at retaining tabs

-arrows-, using removal wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unlock electrical plug connections -2- from closing flange, and

remove.
– Unlock electrical plug connections -1- and -3- from closing
flange, and disconnect.
– Unclip electrical plug connections -1- and -3- from the uptakes
on the closing flange.

Note

Ensure that the fuel delivery unit is not damaged when loosening
and tightening the lock ring of the holder on the flange.

– Open lock ring with the wrench - T30101 (3087)- .

246 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Carefully raise closing flange -2- and remove it from the fuel
tank opening.

Note

Remove gasket ring -3- from fuel tank opening.

– Remove the suction jet pump -1- from the fuel gauge sender
2 - G169- . To do so, carefully bend the retaining lugs
-arrows- outwards.

WARNING

Place a cleaning cloth underneath in order to collect the fuel.

– Remove the fuel gauge sender 2 - G169- carefully out of the

fuel tank opening. Turn and tilt accordingly to do so.

Note

Make sure that the float arm of the fuel gauge sender 2 - G169-
is not bent.

– Pull the suction jet pump through the opening for the fuel
gauge sender 2 - G169- on the fuel tank.

Note

♦ You must be compliance with the environmental regulations

when disposing of it.
♦ Check fuel tank for contaminations.

Install
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Installation occurs unless
in reverse
authorisedorder
by ŠKODAto AUTO
removal. Pay AUTO
A. S. ŠKODA attention to not guarantee or accept any liability
A. S. does
the following: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Note

♦ Note the fitting position of all parts.

♦ Replace damaged gasket rings.

– Slide in the suction jet pump with the fuel gauge sender 2 -
G169- into the fuel tank through the left opening.
– Guide the suction jet pump to the fuel delivery unit.
– Reach into the fuel tank through the opening and press the
pressure line onto the fuel delivery unit until it audibly locks
into place.
– Slide the drive jet line in until there is an audible click.
– Check that the connector and lines at the fuel delivery unit are
seated firmly by pulling in the opposite direction.

2. Removing and installing parts of the fuel supply system 247

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Fit the suction jet pump to the fuel gauge sender 2 - G169- ,
to do so, bend the retaining lugs -arrows- one after the other,
and insert the suction jet pump.
– Check for firm seating by pulling in the opposite direction.
– Insert dry gasket ring of the fuel delivery unit into the opening
of the fuel tank.

Note

When inserting the fuel delivery unit and fuel gauge sender 2 -
G169- , ensure that the float arm of the fuel gauge sender is not
bent.

– Coat inner side of gasket rings -1- with fuel.

– Push closing flange -2- downwards against spring force on
both sides.
– Bring the two closing flanges -2- into the fitting position.

– Arrow -3- at the fuel tank must point

unless authorised to marking
by ŠKODA AUTO A. S.-2- onAUTO
ŠKODA the A. S. does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

closing flange -1-. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

WARNING

Risk of leakage.
♦ The gasket ring must not get damaged or squashed when
inserting the sealing flange.

Note

Ensure that the fuel delivery unit is not damaged when tightening
the lock ring of the holder on the flange.

248 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Tighten lock ring with wrench - T30101 (3087)- to 110 Nm.

– Mount all fuel lines and connectors to the closing flanges on
both sides.
– Check that the connector and lines at the fuel delivery unit are
seated firmly by pulling in the opposite direction.
Vehicles fitted with auxiliary heating
– Observe the fitting position of the fuel discharge line for aux‐
iliary heating ⇒ Heating, Air Conditioning; Rep. gr. 82 .
♦ Tightening torques, assembly instructions ⇒ page 194 .

2.22 Inspecting uel pump - G6-

⇒ “2.22.1 Checking fuel pressure”, page 249
⇒ “2.22.2 Checking fuel delivery rate”, page 255

2.22.1 Checking fuel pressure

Special tools and workshop equipment required
♦ Pressure gauge - VAS 6551-
♦ Adapter set - VAS 6551/5-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Disassembly
unless authorised by ŠKODA wedge
AUTO A.- 3409-
S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Hose binding claw - V.A.G 1921-

WARNING

Ensure that when the battery is connected the fuel pump can‐
not be activated by the opening door! Fuel can spill out when
the system is open.

Test requirements:
• Connect battery charger, the battery voltage must be at least
12.5 volts ⇒ Electrical System; Rep. gr. 27 .
• Fuses o.k. ⇒ Current flow diagrams, Electrical fault finding and
Fitting locations.
• Fuel pump control unit - J538- OK ⇒ Vehicle diagnostic tester.
• Fuel filter o.k.
• Ensure level vehicle positioning.
• Fuel tank at least 1/2 full.
• All electrical components such as lights and rear window heat‐
er must be switched off.

2. Removing and installing parts of the fuel supply system 249

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

♦ The vehicle must be refuelled with diesel fuel corresponding

to the season. Summer diesel can sometimes coagulate at low
winter temperatures.
♦ Diesel fuel sold in summer is guaranteed filterable to 0 °C.
♦ Diesel fuel sold during the transitional period is guaranteed
filterable to -10 °C.
♦ Diesel fuel sold in winter is guaranteed filterable to -20 °C.
♦ If there is uncertainty in winter, take a sample.
♦ Expose the sample to approximately 1 hour of low outside
temperature.
♦ If the fuel flocculates at temperatures to -20 °C, the diesel fuel
is unsuitable for low temperatures. This flocculation can clog
the strainer of the fuel delivery unit and the fuel filter.

Test procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Switch off ignition.

– Remove engine cover at the top ⇒ page 9 .
– Open clamp -arrow-.
– Pull fuel feed line -1- off the high pressure pump -2-.

250 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Insert connecting nipple - VAS 6551/5-1- in the feed line -1-

and secure using a clamp.
– Connect the hose line - VAS 6551/2- between connecting nip‐
ple - VAS 6551/5-1- and connection -A- of the pressure gauge
(Diesel) - VAS 6551- .
– Connect hose line - VAS 6551/5-2- between the connection
-B- of the pressure gauge (Diesel) - VAS 6551- and the high
pressure pump -2-.
– Secure hose line - VAS 6551/5-2- to the high pressure pump
-2- using a clamp.
– Switch on the pressure gauge - VAS 6551- by pressing the
button On/Off .

– Open shut-off taps -A- and -B- of the pressure gauge - VAS
6551- -1-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Make sure that the
withshut-off tapcorrectness
respect to the -C- is closed at the
of information in thispressure
document. Copyright by ŠKODA AUTO A. S.�
gauge - VAS 6551- -1-.
– Connect a
vehicle diagnosis tester
.
– Select Targeted Function 01 activate fuel pump .
– Select function check fuel pump conveying pressure/
quantity .

– Follow the instructions of the vehicle diagnosis tester .

Note

The fuel pump is now activated.

– Read fuel pressure on pressure gauge - VAS 6551- .

• Specified value: at least 0.45 MPa (4.5 bar):
If the specification is not attained:
– Check fuel lines in the engine compartment for possible re‐
strictions (kinks) or blockages and damage.
– Check the fuel lines in the engine compartment for tightness.
If no fault is found:
Check the fuel pressure before the fuel filter, to do so proceed as
follows.
Check the fuel pressure before the fuel filter:

2. Removing and installing parts of the fuel supply system 251

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove fuel feed line -1-. Unlock the quick coupling and dis‐
connect ⇒ page 226 .

– Connect hose line - VAS 6551/2- between the fuel feed line
from the fuel tank and connection -B- from the pressure gauge
- VAS 6551- .
– Connect hose line - VAS 6551/1- between the connection
-A- from the pressure gauge (Diesel) - VAS 6551- and the fuel
line to the fuel filter -1-.
– Switch on the pressure gauge - VAS 6551- by pressing the
button On/Off .

– Open shut-off taps -A- and -B- of the pressure gauge - VAS
6551- -1-.
– Make sure that the shut-off tap -C- is closed at the pressure
gauge - VAS 6551- -1-.
– Repeat function check fuel pump conveying pressure/
quantity ⇒ page 251 .

If the specification is now attained:

Check fuel filter, replace if necessary ⇒ page 196 .
If the specification is not attained:
Proceed as follows to check fuel pressure at fuel delivery unit.
Check fuel line at the fuel delivery unit
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .

252 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unclip cover -1- at retaining tabs -arrows-, using removal

wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

– Unhook the electrical plug connections -3- for the dosing pump
- V54- at the fuel delivery unit.

– Push up catch -2- in -arrow direction A- - to do so, reach be‐

2. Removing and installing parts of the fuel supply system 253

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock fuel feed line -1- on closing flange and pull off. Unlock
the quick coupling and disconnect ⇒ page 226 .

– Connect connection line - VAS 6551/5-3- between the pres‐

sure gauge - VAS 6551- and the fuel feed line to the fuel filter
-2-.
– Connect connection line - VAS 6551/5-4- between pressure
gauge - VAS 6551- and fuel delivery unit-1-.

– The shut-off taps -A- and -B- must be open at the pressure
gauge - VAS 6551- -1-.
– Make sure that the shut-off tap -C- is closed at the pressure
gauge - VAS 6551- -1-.
– Repeat function check fuel pump conveying pressure/
quantity ⇒ page 251 .

If the specified value is reached:

– Check fuel lines to the engine for possible restrictions (kinks)
or blockages and damage.
– Test fuel lines for tightness.
If the specification is not attained:
– Remove fuel delivery unit:
♦ Removing and installing the fuel delivery unit, vehicles with
front-wheel drive ⇒ page 210 .
♦ Removing and installing the fuel delivery unit, vehicles with
four-wheel drive ⇒ page 214 .
– Check filter strainer for soiling.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

254 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Check that all hose connections are connected -arrows-.

If no fault is found:
– Replace fuel delivery unit:
♦ Removing and installing the fuel delivery unit, vehicles with
front-wheel drive ⇒ page 210 .
♦ Removing and installing the fuel delivery unit, vehicles with
four-wheel drive ⇒ page 214 .

2.22.2 Checking fuel delivery rate

Special tools and workshop equipment required
♦ Pressure gauge - VAS 6551-
♦ Adapter set - VAS 6551/5-
♦ Disassembly wedge - 3409-
♦ Hose binding claw - V.A.G 1921-
♦ Pressure control valve - VAS 6551/6-
♦ Measuring container, capacity at least 3 litres

WARNING

Ensure that when the battery is connected the fuel pump can‐
not be activated by the opening door! Fuel can spill out when
the system is open.

Test requirements:
• Connect battery charger, the battery voltage must be at least
12.5 volts ⇒ Electrical System; Rep. gr. 27 .
• Fuses o.k. ⇒ Current flow diagrams, Electrical fault finding and
Fitting locations.
• Fuel pump control unit - J538- OK ⇒ Vehicle diagnostic tester.
• Fuel filter o.k.
• Fuel tank at least 1/2 full.
• Ensure level vehicle positioning.
• All electrical components such as lights and rear window heat‐
er must be switched off.
• Fuel pressure OK ⇒ page 249 .

255
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
2. Removing and installing parts of the fuel supply system
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

♦ The vehicle must be refuelled with diesel fuel corresponding

to the season. Summer diesel can sometimes coagulate at low
winter temperatures.
♦ Diesel fuel sold in summer is guaranteed filterable to 0 °C.
♦ Diesel fuel sold during the transitional period is guaranteed
filterable to -10 °C.
♦ Diesel fuel sold in winter is guaranteed filterable to -20 °C.
♦ If there is uncertainty in winter, take a sample if necessary.
Expose the sample to approximately 1 hour of low outside
temperature. If the fuel flocculates at temperatures to -20 °C,
the diesel fuel is unsuitable for low temperatures. This floccu‐
lation can clog the strainer of the fuel delivery unit and the fuel
filter.

Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Switch off ignition.

– Remove engine cover at the top ⇒ page 9 .
– Move front right seat forward.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Open clamp -arrow- at the fuel feed line -1-.
– Pull fuel feed line -1-Protected
off thebyhigh pressure pump -2-.
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

256 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Insert connecting nipple - VAS 6551/5-1- into fuel feed line and
secure using a clamp.
– Connect the hose line - VAS 6551/2- between connecting nip‐
ple - VAS 6551/5-1- and connection -A- of the pressure gauge
(Diesel) - VAS 6551- .
– Connect pressure control valve - VAS 6551/6- to connection
-B- of the pressure gauge - VAS 6551- .
– Hold the open end of the hose from the pressure control valve
- VAS 6551/6- in a measuring vessel.
– Switch on the pressure gauge - VAS 6551- by pressing the
button On/Off .

– Make sure that the shut-off tap -C- is closed at the pressure
gauge - VAS 6551- -1-.
– The shut-off taps -A- and -B- must be open at the pressure
gauge - VAS 6551- -1-.
– Connect a
vehicle diagnosis tester
.
– Select Targeted Function 01 activate fuel pump .
– Select function check fuel pump conveying pressure/
quantity .

– Follow the instructions of the vehicle diagnosis tester .

– Using the pressure control valve - VAS 6551/6- , set pressure
to 0.45 MPa (4.5 bar).

2. Removing and installing parts of the fuel supply system 257

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Set primary pressure at setting wheel -arrow- by turning pres‐

sure control valve - VAS 6551/6- .
• Specified value: Pressure 0.45 MPa (4.5 bar)
– From this point no longer move position of the setting wheel
-arrow-.
– Drain measuring container.
– Repeat function check fuel pump conveying pressure/
quantity .

Note

The Die fuel system pressurisation pump - G6- is now activated

for 30 seconds.

– Check fuel delivery quantity in the measuring vessel.

• Specified value: Minimum delivery quantity 1100 cm3/30 sec‐
onds.
If the minimum flow rate is not reached:
– Check fuel lines in the engine compartment for possible re‐
strictions (kinks) or blockages and damage.
– Check the fuel lines in the engine compartment for tightness.
If no fault is found:
Check the fuel delivery quantity before the fuel filter, to do so pro‐
ceed as follows:
Check the fuel delivery quantity before the fuel filter:

– Remove fuel feed line -1-. Unlock the quick coupling and dis‐
connect ⇒ page 226 .

258 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect hose line - VAS 6551/2- to the fuel feed line from the
fuel tank.
– Connect the hose line - VAS 6551/2- at the connection -A- of
the pressure gauge (Diesel) - VAS 6551- .
– Connect pressure control valve - VAS 6551/6- to connection
-B- of the pressure gauge - VAS 6551- .
– Hold the open end of the hose from the pressure control valve
- VAS 6551/6- in a measuring vessel.
– Switch on the pressure gauge - VAS 6551- by pressing the
button On/Off .

– Make sure that the shut-off tap -C- is closed at the pressure
gauge - VAS 6551- -1-.
– The shut-off taps -A- and -B- must be open at the pressure
gauge - VAS 6551- -1-.
– Repeat function check fuel pump conveying pressure/
quantity ⇒ page 257 .

If the minimum delivery rate is now attained:

Check fuel filter, replace if necessary ⇒ page 196 .
If the specifications are still not attained:
Proceed as follows to check fuel delivery rate at fuel delivery unit.
Check fuel delivery quantity at the fuel delivery unit:

– Unclip cover -1- at retaining tabs -arrows-, using removal

wedge - 3409- .

– Unclip sealing grommet -1- downwards from the cover -2-.

– Guide the cover -2- backward at the electric wiring loom -3-.

2. Removing and installing parts of the fuel supply system 259

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unlock fuel feed line -1- on closing flange and pull off. Unlock
the quick coupling and disconnect ⇒ page 226 .

– Connect connection line - VAS 6551/5-4- to the fuel feed line

connection on the fuel delivery unit -1-.
– Connect connection line - VAS 6551/5-4- to connection -A-
from pressure gauge - VAS 6551- .
– Connect pressure control valve - VAS 6551/6- to connection
-B- of the pressure gauge - VAS 6551- .
– Hold the open end of the hose from the pressure control valve
- VAS 6551/6- in a measuring vessel.
– Switch on the pressure gauge - VAS 6551- by pressing the
button On/Off .

If the minimum delivery rate is now attained:

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Check fuel lines for possible restrictions (kinks) or blockages
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
and damage.
– Test fuel lines for tightness.
If the specifications are still not attained:
– Remove fuel delivery unit:
♦ Removing and installing the fuel delivery unit, vehicles with
front-wheel drive ⇒ page 210 .
♦ Removing and installing the fuel delivery unit, vehicles with
four-wheel drive ⇒ page 214 .
– Check filter strainer for soiling.

260 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Check that all hose connections are connected -arrows-.

Only if no fault has yet been detected:
– Replace fuel delivery unit:
♦ Removing and installing the fuel delivery unit, vehicles with
front-wheel drive ⇒ page 210 .
♦ Removing and installing the fuel delivery unit, vehicles with
four-wheel drive ⇒ page 214 .

2.23 Check sender for fuel gauge display - G-

Special tools and workshop equipment required
♦ Multimeter , e.g. -V.A.G 1526E-
♦ Measuring tool set , e.g. -V.A.G 1594 C-
♦ Disassembly wedge - 3409-
Procedure
– Move front seats all the way forward.
– Switch off ignition.
– Removing rear seat bench ⇒ Body Work; Rep. gr. 72 .
– Unclip cover -1- using the disassembly wedge - 3409- from the
uptake -arrows-.

– Disconnect electrical plug connections -2- on the closing

flange, thereby unlocking the plug lock.

Note

-Ignore positions 1, 3-.

2. Removing and installing parts of the fuel supply system 261

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Sender for fuel gauge display - G- installed:

Note

To achieve a precise indication of the resistance with a “full fuel

tank ” the fuel tank must be filled completely with the sender in‐
stalled. After filling of the full fuel tank, drive at least 500 m so that
any air bubbles can escape from the fuel tank. Then top up.

– Connect multimeter to resistance measurement between con‐

tacts -B1- and -B2-.
• Fuel tank empty: approximately 270 Ω.
• Fuel tank full: approximately 70 Ω.
– Connect multimeter to resistance measurement between con‐
tacts -B1- and -B3-.
• Fuel tank empty: approximately 70 Ω.
• Fuel tank full: approximately 270 Ω.
– Connect multimeter to resistance measurement between con‐
tact -B2- and -B3-.
• Fuel tank sender position: approximately 340 Ω.

Sender for fuel gauge display - G- removed:

Note

♦ When testing resistance values with “fuel tank full ” or “fuel tank
empty ” the sender for fuel gauge display - G- must be removed
and the float arm must be displaced to the top or bottom.
♦ Because of the large displacement of the float arm, the fol‐
lowing values are reached when the sender for fuel gauge
display is removed:

– Connect multimeter to resistance measurement between con‐

tacts -B1- and -B2-.
• Fuel tank empty: approximately 300 Ω.
• Fuel tank full: approximately 52 Ω.
– Connect multimeter to resistance measurement between con‐
tacts -B1- and -B3-.
• Fuel tank empty: approximately 52 Ω.
• Fuel tank full: approximately 300 Ω.
– Connect multimeter to resistance measurement between con‐
tact -B2- and -B3-.
• Fuel tank sender position: approximately 340 Ω.
The sender for fuel gauge display - G- is faulty if the following facts
are established:
♦ Large variations of measured
Protected values.
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Measured valuewith
0 respect
Ω (short
to thecircuit).
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Measured value ∞ Ω (line break).

♦ No fault on electric cables.
– Install sender for fuel gauge display - G- ⇒ page 223 .

262 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 Accelerator mechanism

3.1 Assembly overview - accelerator module

1 - 9 Nm
2 - Connector
❑ Ensure safe locking and
check that the connec‐
tor is correctly locked in‐
to place by pulling it
3 - Accelerator pedal module
❑ with accelerator pedal
position sender - G79-
and accelerator pedal
position sender 2 -
G185-
❑ removing and installing
⇒ page 263

3.2 Removing and installing accelerator

module
Removing
– Bend up carpet cover for accelerator pedal.

3. Accelerator mechanism 263

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connections -2- on the accelerator

pedal module, thereby pressing the release upwards.
– Release screw -1-.
– Remove accelerator module -3- from the uptake.
Install
Installation is carried out in the reverse order. When installing,
note the following:
♦ Tightening torque, assembly instructions
⇒ “3.1 Assembly overview - accelerator module ”, page 263

Caution

Risk of damage to knee airbag surface by mechanical stress.

♦ After completion of the visual inspection, check that the
knee airbag surface is not damaged.

264 Rep. gr.20 - Fuel supply system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

21 – Turbocharging/supercharging
1 Charge-air system - exhaust gas tur‐
bocharger

1.1 Exhaust gas turbocharger with component parts - Summary of components

1 - Hollow screw, 30 Nm
2 - Oil feed line
❑ check continuity
❑ before installing, fill the
exhaust turbocharger
on the connection fitting
for the oil feed line with
engine oil
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
3 - 12 Nm
4 - Union nut, 22 Nm
5 - Exhaust gas temperature
sender 1 - G235-
❑ Summary of compo‐
nents ⇒ page 370
6 - Bolt
❑ for vehicles with ex‐
haust gas cleaning
module ⇒ page 357
❑ Tightening torque and
tightening order
⇒ page 266
7 - 15 Nm
8 - Heat shield
9 - O-ring
❑ replace after removal
10 - Pulsation dampener
❑ Observe part
Protected by number ⇒ for private or commercial purposes, in part or in whole, is not permitted
copyright. Copying
ETKAunless
- Electronic
authorised by Cata‐
ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
logue ofwithOriginal Parts
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

11 - 8 Nm
12 - Inlet connections
13 - 8 Nm
14 - O-ring
❑ replace after removal
15 - Bracket
❑ for electrical cables

1. Charge-air system - exhaust gas turbocharger 265

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

16 - 15 Nm
17 - Heat shield
18 - Exhaust gas turbocharger
❑ removing and installing ⇒ page 267
❑ For vehicles with engine identification characters CKFB, CKFC, CRVC, CUPA: Replace vacuum posi‐
tioning element for charge pressure regulation with position sender for charge pressure regulator - G581-
⇒ page 276
❑ Observe part number ⇒ ETKA - Electronic Catalogue of Original Parts
19 - Gasket
❑ replace after removal
❑ Observe part number ⇒ ETKA - Electronic Catalogue of Original Parts
20 - Nut
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 267
21 - Support
❑ for exhaust gas cleaning module ⇒ page 357
❑ Tightening torque and tightening order ⇒ page 266
22 - Screw
❑ for vehicles with exhaust gas cleaning module ⇒ page 357
❑ Tightening torque and tightening order ⇒ page 266
23 - Seal
❑ replace after removal
24 - O-ring
❑ replace after removal
❑ wet with engine oil
25 - Oil return-flow line Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
26 - 10 Nm
27 - Ribbed bolt, 14 Nm
28 - Gasket rings
❑ replace after removal

Bracket for exhaust gas cleaning module - tightening torques and

tightening order
– Bring holder to installation position.
– Tighten screws in steps in the specified sequence:
Stage Screws Tightening torque
1. -1, 2, 3, 4- by hand as far as the stop
2. -2- 20 Nm
3. -1- 40 Nm
4. -3, 4- 40 Nm

266 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Exhaust gas turbocharger - tightening torque and tightening order

– Tighten screws in steps in the specified sequence:
Stage Screws Tightening torque
1. -Arrows- from inside to outside crosswise 11
Nm
2. -Arrows- from inside to outside crosswise 22
Nm
3. -Arrows- from inside to outside crosswise 22
Nm
• This measure takes account of the
settling behaviour of components

1.2 Removing and installing exhaust gas

turbocharger
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
♦ Socket insert XZN 10 - T10501-

Caution

In case of mechanical damage to the exhaust gas turbocharg‐

er, e.g. damage of the compressor wheel, it is not sufficient to
only replace the exhaust gas turbocharger. In order to prevent
consequential damage
Protected by copyright. to forthe
Copying engine,
private perform
or commercial the
purposes, following
in part or in whole, is not permitted
tasks: with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability

♦ Clean all oil lines.

♦ Change engine oil and oil filter.
♦ Check air filter housing, air filter element and charge air
pipes as well as charge air hoses for soiling.
♦ Check all the air guides and the charge air cooler for for‐
eign bodies.
If foreign bodies are detected in the charge air system, the
complete charge-air routing must be cleaned and if necessary
the charge air cooler must also be replaced.

Note

♦ Observe rules for cleanliness ⇒ page 7 .

♦ Observe general instructions for charge-air system
⇒ page 7 .

Removing

Note

Fit all heat protection sleeves on again in the same place when
installing.

– Remove engine cover at the top ⇒ page 9 .

1. Charge-air system - exhaust gas turbocharger 267

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Drain coolant ⇒ page 139 .

– Remove rear coolant pipe ⇒ page 164 .
– Remove pre-exhaust pipe ⇒ page 349 .
– Remove left coolant pipe ⇒ page 163 .
Right-hand drive
– Remove exhaust gas cleaning module ⇒ page 360 .
Left-hand drive
– Press release buttons on the hose -1- for crankcase ventilation
and remove from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

Note

-Do not pay attention to the position 3-.

– Release screws -arrows- and remove pre-volume tank -1-.

– Open heat protection sleeve -1-.

– Take electrical plug connection-4 - out of the holder, discon‐
nect and expose electric cable.
– Disconnect electrical plug connections -3, 5-, expose electric
wiring loom.
– Unscrew screw -2-, lay bracket with differential pressure send‐
er - G505- to the rear.

268 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen hose clamp -1-, remove coolant hose.

– Unscrew screw -2-, remove screw -3- and swivel coolant line
to the side.

– Expose the following plug connections and electric cables:

2 - for exhaust gas temperature sender 4 - G648-
3 - for exhaust gas temperature sender 3 - G495-
– Take electrical plug connection-4- for lambda probe - G39- out
of the holder, disconnect and expose electric cable.
Vehicles with four-wheel drive
– Remove radiator for exhaust gas recirculation ⇒ page 381 .
Vehicles with auxiliary heating

– Raise holding clamp -1- and loosen hose clamp -2-, remove
coolant hoses.
– Release nuts -arrows-, remove coolant pipe.
Continued for left-hand drive vehicles

– Press heat protection sleeve to the side, disconnect electrical

plug connection -5-.
– Loosen hose clamp -3-, remove air guide hose.
– Loosen hose clamp -4-, remove coolant hose.
– Unscrew
Protectedscrew -1- Copying
by copyright. using forsocket insert
private or XZN
commercial 10 - T10501-
purposes, , is not permitted
in part or in whole,
loosen screw -2-.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

WARNING

When pressing out the exhaust gas cleaning module, take ac‐
count of electric cable of exhaust gas temperature sender 1 -
G235- -1-!

1. Charge-air system - exhaust gas turbocharger 269

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Loosen screw -1- and remove screw clamp.

– Slacken the double screw -2-, lay coolant pipe backwards
slightly.
– Unscrew screws -arrows-, push exhaust gas cleaning module
and exhaust gas recirculation cooler backwards.
Continued for all vehicles

– Release hollow screw -1-, unscrew screw -2- and union nut
-4-, remove oil feed line.
– Unscrew screws -3, 5-, remove oil return-flow line.

270 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws 1-…4- and remove bracket for diesel particle

filter.

– Release screws -arrows- and remove heat shield -1-.

– Remove the vacuum hose -2- from the vacuum unit for charge
pressure control.

Note

-Do not pay attention to the position 1-.

1. Charge-air system - exhaust gas turbocharger 271

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew nuts -arrows- and remove the exhaust gas turbo‐

charger with exhaust manifold from the cylinder head.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace sealing rings, gaskets, O-rings and the self-locking

nuts after disassembly.
♦ Fill the exhaust turbocharger with engine oil at the connection
fitting for the oil feed line.
♦ Observe the assembly instruction for hose connections with
screw clamps ⇒ page 281 .
♦ Hose connections and air guide pipes and hoses must be free
of oil and grease before being installed.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .
♦ To ensure the oil supply to the exhaust gas turbocharger,
leave the engine running for about 1 minute after installing the
exhaust gas turbocharger; do not rev up immediately.

– Electrical connections and proper routing ⇒ Electrical System;

Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
– Install exhaust gas cleaning module ⇒ page 360 .
– Install the left coolant pipe ⇒ page 163 .
– Install pre-exhaust pipe ⇒ page 349 .
– Install the rear coolant pipe ⇒ page 164 .
– Connect vacuum hose ⇒ page 279 .
Tightening torques
♦ Summary of components - exhaust gas turbocharger with
component parts
⇒ “1.1 Exhaust gas turbocharger with component parts - Sum‐
mary of components”, page 265
♦ Bracket for exhaust gas cleaning module - tightening torques
and tightening order
⇒ Fig. ““Bracket for exhaust gas cleaning module - tightening
torques and tightening order”“ , page 266
♦ Summary of components - exhaust gas cleaning
⇒ “2.1 Summary of components - exhaust gas cleaning”, page
357

1.3 Removing and installing exhaust gas

turbocharger
For vehicles with engine identification characters CRVC
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362- Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Socket insert XZN 10 - T10501- with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

272 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Caution

In case of mechanical damage to the exhaust gas turbocharg‐

er, e.g. damage of the compressor wheel, it is not sufficient to
only replace the exhaust gas turbocharger. In order to prevent
consequential damage to the engine, perform the following
tasks:
♦ Clean all oil lines.
♦ Change engine oil and oil filter.
♦ Check air filter housing, air filter element and charge air
pipes as well as charge air hoses for soiling.
♦ Check all the air guides and the charge air cooler for for‐
eign bodies.
If foreign bodies are detected in the charge air system, the
complete charge-air routing must be cleaned and if necessary
the charge air cooler must also be replaced.

Note

♦ Observe rules for cleanliness ⇒ page 7 .

♦ Observe general instructions for charge-air system
⇒ page 7 .

Removing

Note

Fit all heat protection sleeves on again in the same place when
installing.

– Remove engine cover ⇒ page 9 .

– Drain coolant ⇒ page 139 .
– Remove pre-exhaust pipe ⇒ page 349 .
– Remove rear coolant pipe ⇒ page 164 .
– For vehicles with auxiliary heating, remove coolant hoses from
front wall ⇒ Heating, Air Conditioning; Rep. gr. 82 .
– Press release buttons on the hose -1- for crankcase ventilation
and remove from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

273
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
1. Charge-air system - exhaust gas turbocharger
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -arrows- and remove pre-volume tank -1-.

– Disconnect the line from the exhaust temperature sender 1 -
G235- .
– Remove catalytic converter ⇒ page 368 .
– Remove radiator for exhaust gas recirculation ⇒ page 381

– Release screws -1...5- and remove bracket for radiator for ex‐
haust gas recirculation.

– Release nut -2- and remove union nut -4-.

– Unscrew screws -3, 5-, remove oil return-flow line.

– Release screws -arrows- and remove heat shield -1-.

274 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove the vacuum hose -2- from the vacuum unit for charge
pressure control.

– Unscrew nuts -arrows- and detach the exhaust gas turbo‐

charger with exhaust manifold from the cylinder head, and
remove from the top.
Install
Install in the reverse order of removal. When doing this, note the
following:

Note

♦ Replace sealingProtected
rings,bygaskets, O-rings
copyright. Copying andorthe
for private self-locking
commercial purposes, in part or in whole, is not permitted
nuts after disassembly.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Fill the exhaust turbocharger with engine oil at the connection
fitting for the oil feed line.
♦ Hose connections and air guide pipes and hoses must be free
of oil and grease before being installed.
♦ Secure all hose connection ends with spring-type clips that
comply with the series design ⇒ ETKA - Electronic Catalogue
of Original Parts .
♦ To ensure the oil supply to the exhaust gas turbocharger,
leave the engine running for about 1 minute after installing the
exhaust gas turbocharger; do not rev up immediately.

– Electrical connections and proper routing ⇒ Electrical System;

Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
– Install the rear coolant pipe ⇒ page 164 .
– Install mounting bracket for radiator for exhaust gas recircu‐
lation ⇒ page 378 .
– Install radiator for exhaust gas recirculation ⇒ page 383 .
– Install high catalytic converter ⇒ page 368 .
– Install pre-exhaust pipe ⇒ page 349 .
– Connect vacuum hose ⇒ page 279 .
Tightening torques
♦ Summary of components - exhaust gas turbocharger with
component parts
⇒ “1.1 Exhaust gas turbocharger with component parts - Sum‐
mary of components”, page 265
♦ Summary of components - exhaust gas cleaning
⇒ page 359

1. Charge-air system - exhaust gas turbocharger 275

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.4 Replace vacuum positioning element for

charge pressure regulation with position
sender for charge pressure regulator -
G581-
Special tools and workshop equipment required
♦ Hand vacuum pump - VAS 6213-
Removing
– Remove engine cover ⇒ page 9 .
Version 1:
– Disconnect the electrical plug connection -3- from the position
sender for charge pressure regulator - G581- .
– Remove the vacuum hose -2- from the vacuum unit for charge
pressure control.
– Remove detention ring -4-.
– Release screws -1- from the pressure box.
– Unhook the control rod from the adjuster lever and remove the
pressure box with position sender for charge pressure regu‐
lator - G581- .

Version 2:
– Disconnect the electrical plug connection -2- from the position
sender for charge pressure regulator - G581- .
– Remove the vacuum hose -1- from the vacuum unit for charge
pressure control.
– Remove detention ring -4-.
– Unscrew screws -3- from the pressure box.
– Unhook the control rod from the adjuster lever and remove the
pressure box with position sender for charge pressure regu‐
lator - G581- .
Install

Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Use new screws and a new circlip from the repair kit!

276 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Version 1:
– Hook in the control rod at the adjuster lever, attach the pres‐
sure box, and turn in the screws -1- as far as they can go by
hand.
– Install the circlip -4-.
– Connect the electrical plug connection -3- to the position send‐
er for charge pressure regulator - G581- .

Version 2:
– Hook in the control rod at the adjuster lever, attach the pres‐
sure box, and turn in the screws -3- as far as they can go by
hand.
– Install the circlip -4-.
– Connect the electrical plug connection -2- to the position send‐
er for charge pressure regulator - G581- .
Continued for all versions
– Adjust the control rod for the dashpot, measuring the initial
tension as you do so.
– You must use ⇒ Vehicle diagnostic tester.
• Targeted functions

• 01 - read measured value block

– Put the sliding ring -1- of the hand vacuum pump - VAS 6213-
in position-A- for “vacuum”

1. Charge-air system - exhaust gas turbocharger 277

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect the hand vacuum pump - VAS 6213- to the pressure

box -arrow-.

Caution

Risk of damage to the pressure box from excessive vacuum.

♦ Under no circumstances, must a vacuum greater than
-800 mbar be generated.

Adjust the voltage value

– Using the hand vacuum pump - VAS 6213- continue pumping
until the pressure gauge indicates a vacuum between
-650…-700 mbar.

Version 1:
– Slide the pressure box in the -direction of arrow- until a voltage
of 0.75 ± 0.02 V appears on the ⇒ Vehicle diagnostic tester.
– Tighten screws -1- to 10 Nm.

Version 2:
– Slide the pressure box in the -direction of arrow- until a voltage
of 0.75 ± 0.02 V appears on the ⇒ Vehicle diagnostic tester.
– Tighten screws -1- to 10 Nm.

278 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Put the sliding ring -1- of the hand vacuum pump - VAS 6213-
into position -B- to ensure the pressure box is vented until the
pressure reaches the ambient pressure.
Check the voltage value
– Put the sliding ring -1- of the hand vacuum pump - VAS 6213-
in position-A- for “vacuum”
– Using the hand vacuum pump - VAS 6213- continue pumping
until the pressure gauge indicates a vacuum between
-650…-700 mbar.
– The ⇒ Vehicle diagnostic tester should now indicate a voltage
of 0.75 ± 0.02 V.

Voltage not OK.

Note

Version 1 is shown as an example.

– Release screws -1-.

– Adjust the voltage value ⇒ page 278 .
Voltage value o.k. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Coat the screws with sealing varnish
with respect from the
to the correctness repair inkit.
of information this document. Copyright by ŠKODA AUTO A. S.�

– Install the engine cover ⇒ page 9 .

– Start engine and erase fault memory ⇒ Vehicle diagnostic
tester.

1.5 Connection diagram for vacuum hoses

1. Charge-air system - exhaust gas turbocharger 279

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Vacuum line
2 - Non-return valve
❑ Check fitting position
❑ the positive side points
to the cylinder head cov‐
er
3 - Cylinder head cover
❑ with vacuum unit
4 - Vacuum unit
❑ at exhaust gas turbo‐
charger
❑ with position sender for
charge pressure regula‐
tor - G581-
❑ for charge pressure
control
5 - Head tube for vacuum
❑ from charge pressure
control solenoid valve -
N75- for vacuum unit on
the exhaust gas turbo‐
charger
6 - Solenoid valve for charge
pressure control - N75-
7 - To the brake servo unit
8 - Non-return valve
❑ Check fitting position
9 - Vent line
10 - To air filter housing
11 - To vacuum pump
❑ in the oil pump
⇒ page 116

1.6 Checking vacuum system

Special tools and workshop equipment required
♦ Hand vacuum pump , e.g. -VAS 6213-
Procedure
– Check all the vacuum lines in the complete vacuum system
for:
♦ tears
♦ Interruption (marten bites)
♦ Crimping
♦ porous points and other leaks
– Check vacuum line to the solenoid valve and check solenoid
valve for the respective component.
– In the event of an event memory entry, check the vacuum lines
to the mentioned Protected
component and also the remaining vacuum
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
lines to the other unless
components.
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

280 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– If no vacuum can be created or the vacuum drops immediately

with the hand vacuum pump - VAS 6213- , check hand vacuum
pump and connecting hoses for leaks.

1.7 Hose connections with screw clamps

Note

♦ Connections, charge air pipes and hoses of charge air system

must be free of oil and grease before being installed.
♦ Only install approved screw clamps for securing the hose con‐
nections ⇒ ETKA - Electronic Catalogue of Original Parts .
♦ In order to secure the charge air hoses on their connection
fittings, the threads must be treated with rust solvent if the
screw clamps have been used beforehand.
♦ After a repair, check all the charge air pipes, charge air hoses
and vacuum lines for tight connection and leaktightness.

Caution

The screw clamps -A- on the charge air hoses must definitely
be precisely tightened in accordance with the specifications
⇒ page 281 .
♦ A too low or on the contrary, a too high tightening torque
of the screw clamps, may result in the charge air hose
slipping off the fluted pipe or the charge air pipe while
driving.

Tightening torques of the screw clamps

1- Hose clamp -a- = 12 mm wide: 5.5 Nm
2- Screw clamp -b- = 9 mm wide: 3 Nm Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1. Charge-air system - exhaust gas turbocharger 281

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Charge-air system - radiator, leak‐

tightness

2.1 Charge air cooling - Summary of components

1 - Sealing ring
❑ replace after removal
2 - Fit pin
3 - 8 Nm
4 - Seal
❑ replace after removal
5 - Screw
❑ Tightening torque and
tightening order
⇒ page 327
6 - Support
❑ for the intake manifold
7 - Screw
❑ Tightening torque and
tightening order
⇒ page 327
8 - Screw
❑ replace after removal
❑ Tightening torque and Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
tightening order unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
⇒ page 326 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

9 - Fit pin
10 - 8 Nm
11 - Intake manifold with
charge air cooler
❑ The intake manifold and
charge air cooler form a
single building unit
❑ removing and installing
⇒ page 329
12 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 326
13 - Charge air temperature sender after charge air cooler - G811- , 22 Nm
❑ removing and installing ⇒ page 313
14 - Seal
❑ replace after removal
15 - Supports
❑ for throttle valve control unit - J338-
16 - Intake air temperature sender - G42- , 22 Nm
❑ removing and installing ⇒ page 313

282 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

17 - 10 Nm
18 - Coolant pipe
19 - 10 Nm
20 - Coolant pipe
21 - O-rings
❑ replace after removal
❑ Moisten with coolant
22 - Throttle valve control unit - J338-
❑ With throttle valve potentiometer - G69-
❑ removing and installing ⇒ page 327
23 - O-ring
❑ replace after removal
24 - Air guide pipe
25 - 8 Nm
26 - Bracket
❑ for throttle valve control unit - J338-
27 - Screw
❑ Tightening torque and tightening order ⇒ page 327
28 - Screw
❑ Tightening torque and tightening order ⇒ page 327

Charge pressure sender - G31- - tightening torque

– Tighten -2- to 9 Nm.

2.2 Removing and installing the charge

pressure sender - G31-
Removing
– Remove engine cover at the top ⇒ page 9 .

2. Charge-air system - radiator, leaktightness 283

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -3-.

– Spray hose with a solvent at charge pressure sender - G31-
before removing it.

Caution

Risk of destruction of the charge pressure sender as a result

of the connection fitting breaking.
♦ Pull hose off carefully and straight from the connection fit‐
ting.

– Release screws -2- and remove charge pressure sender -

G31- .
Install
Installation is carried out in the reverse order. When installing,
note the following:
Tightening torques
♦ Charge pressure sender - G31- - tightening torque
⇒ Fig. ““ Charge pressure sender -G31- - tightening torque”“ ,
page 283

2.3 Checking the charge-air system for

leaktightness
Special tools and workshop equipment required
♦ Charge-air system testing device , e. g. -V.A.G 1687-
♦ Adapter , e.g. -V.A.G 1687/11-
♦ Adapter , e.g. -V.A.G 1687/15-
♦ Hose binding claw
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Test procedure
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove engine cover at the top ⇒ page 9 .

– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Loosen hose clamps -1, 2-, remove air guide pipe.

284 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect adapter with - V.A.G 1687/11- with -V.A.G 1687/15-

to the exhaust gas turbocharger.
– Connect tester for the charge air systems - V.A.G 1687- to the
adapter.
Prepare tester for charge air system - V.A.G 1687- as follows:

– Unscrew pressure control valve -2- fully and close the valves
-3- and -4-.

Note

The rotary knob must be pulled to the top in order to rotate the
pressure control valve -2-.

2. Charge-air system - radiator, leaktightness 285

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect the pneumatic hose -1- (pneumatic support) to tester

for charge air system.

Note

If there is water in the inspection glass, drain water via the drain
plug -6-.

– Open valve -3-.

Caution

The pressure must not be greater than 0.05 MPa (0.5 bar)! A
too high pressure can damage the engine.

– Set the pressure to 0.05 MPa (0.5 bar) with the pressure con‐
trol valve -2-.
– Open valve -4- and wait until the test circuit is filled. If neces‐
sary regulate the pressure to 0.05 MPa (0.5 bar).
– Listen to, touch or use commercially available leak search
spray or the ultrasonic measuring device e. g. -V.A.G 1842- to
check the charge-air system with exhaust gas turbocharger for
leak points.

Note

♦ Minor leaks are permissible on the suction side of the turbo‐

charger, because the intake hoses are not designed for over‐
pressure.
♦ A small amount of air escapes via the valves into the engine.
For this reason no pressure test is possible.
♦ Use of ultrasonic measuring device - V.A.G 1842- ⇒ operating
instructions .
♦ In case of a leak point, observe the instructions for charge air
system ⇒ page 7 during the installation.
♦ Before removing the adapter, depressurize the test circuit by
detaching the hose coupling.

286 Rep. gr.21 - Turbocharging/supercharging

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

23 – Mixture preparation - injection

1 Diesel direct injection system - fitting
location, system overview
The control unit is equipped with a fault memory. Before repairs,
setting operations and fault finding, interrogate the fault memory
and execute a self-diagnosis ⇒ Vehicle diagnostic tester.

Note

♦ Faults can be detected by the control unit as checking and

adjustment work is being undertaken and then saved. It is
therefore absolutely necessary to delete the fault memory af‐
ter completing all checking and adjustment work ⇒ Vehicle
diagnostic tester
♦ Observe the safety precautions when working on the diesel
direct injection system ⇒ page 4 .

1.1 Installation location overview - fuel injection system

Installation location overview - engine compartment

1 - Coolant valve for cylinder

head - N489-
❑ Fitting location
⇒ page 289
2 - Injection units
♦ Injector, cylinder 1 - N30-
♦ Injector, cylinder 2 - N31-
♦ Injector, cylinder 3 - N32-
♦ Injector, cylinder 4 - N33-
❑ Summary of compo‐
nents ⇒ page 295
3 - Differential pressure sender
- G505-
❑ Summary of compo‐
nents ⇒ page 370
4 - Exhaust gas pressure sen‐
sor 1 - G450-
❑ only for vehicles with en‐
gine identification char‐
acters CRKB
❑ Summary of compo‐
nents ⇒ page 322
5 - Position sender for charge
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
pressure regulator - G581-
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
6 - Engine noise speaker
❑ only for vehicles with en‐
gine identification char‐
acters CUPA
❑ removing and installing
⇒ page 339

1. Diesel direct injection system - fitting location, system overview 287

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

7 - Coolant temperature sender - G62-

❑ Summary of components ⇒ page 148
8 - Solenoid valve for charge pressure control - N75-
❑ Electrical plug connection for solenoid valve for charge pressure control - N75-
❑ Electrical plug connection for exhaust gas temperature sender 4 - G648-
❑ Electrical plug connection for exhaust gas temperature sender 3 - G495-
❑ Electrical plug connection for lambda probe - G39-
❑ Fitting location ⇒ page 289
9 - Air mass meter - G70-
❑ Fitting location ⇒ page 289
10 - Engine control unit - J623-
❑ removing and installing ⇒ page 336
11 - Charge pressure sender - G31-
❑ Summary of components ⇒ page 282
12 - Intake air temperature sender - G42-
❑ Summary of components ⇒ page 325
13 - Control valve for fuel pressure - N276-
❑ Summary of components ⇒ page 297
14 - Charge air temperature sender after charge air cooler - G811-
❑ Summary of components ⇒ page 325
15 - Hall sender - G40- (camshaft position sensor)
❑ Summary of components ⇒ page 385
16 - Glow plugs
♦ Glow plug 1 - Q10-
♦ Glow plug 2 - Q11-
♦ Glow plug 3 - Q12- ; for engine identification characters CRKB with combustion chamber pressure sender
for cylinder 3 - G679-
♦ Glow plug 4 - Q13-
❑ Summary of components ⇒ page 385
17 - Fuel pressure sender - G247-
❑ Summary of components ⇒ page 297
18 - Fuel temperature sender - G81-
❑ in the fuel feed line
❑ Protected
removing and installing
by copyright. ⇒ page
Copying for private 313 purposes, in part or in whole, is not permitted
or commercial
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
19 - High
withpressure
respect to thepump
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

❑ with fuel dosage valve - N290- (do not open)

❑ Summary of components ⇒ page 309

288 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Accelerator pedal position sender - G79- and accelerator pedal

position sender 2 - G185-
♦ In the accelerator pedal module.
2 - Electrical plug connections for accelerator pedal module

Note

Accelerator pedal position sender - G79- and accelerator pedal

position sender 2 - G185- are incorporated into the accelerator
pedal module and cannot be replaced individually.

Electrical plug connections

1- Solenoid valve for charge pressure control - N75-
2- Exhaust gas temperature sender 4 - G648-
3- Exhaust gas temperature sender 3 - G495-
4- Exhaust temperature sender 2 - G448- only for vehicles with
engine identification characters CRKB
5- Lambda probe - G39-
6- Air mass meter - G70-

Installation location of exhaust flap control unit - J883-

• in the pre-exhaust pipe
Removing and installing:
♦ For 1.6l engine ⇒ page 340 .
♦ For 2.0l engine ⇒ page 342 .

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Installation location of coolant valve for
withcylinder head
respect to the - N489-
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

• -Pos. 1- top on coolant pump.

Removing and installing ⇒ page 151 .

Installation location overview - engine from left

1. Diesel direct injection system - fitting location, system overview 289

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Charge air cooler pump -

V188-
❑ Summary of compo‐
nents ⇒ page 149
2 - Oil pressure control valve -
N428-
❑ Summary of compo‐
nents ⇒ page 116
❑ removing and installing
⇒ page 129
3 - Control motor for exhaust
gas recirculation - V338- with
exhaust gas recirculation po‐
tentiometer - G212-
❑ only for vehicles with en‐
gine identification char‐
acters CRKB, CRVC
❑ Summary of compo‐
nents ⇒ page 378
4 - Inlet camshaft control valve
1 - N205-
❑ only for vehicles with en‐
gine identification char‐
acters CRKB
❑ Summary of compo‐
nents ⇒ page 98
5 - Throttle valve module -
J338-
❑ With throttle valve po‐ Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
tentiometer - G69- unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ Summary of compo‐
nents ⇒ page 325
6 - Oil pressure switch for re‐
duced oil pressure - F378-
❑ Summary of components ⇒ page 119
7 - Oil pressure switch - F1-
❑ Summary of components ⇒ page 119
8 - Engine speed sender - G28-
❑ Summary of components ⇒ page 385

Installation location overview - engine from right

Note

The Summary of components only concerns vehicles with engine identification characters CLHA, CLHB, CRKB,
CKFB, CKFC, CUPA.

290 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Oil level and oil temperature

sender - G266-
❑ Summary of compo‐
nents ⇒ page 116
2 - Control motor 2 for exhaust
gas recirculation - V339-
❑ Summary of compo‐
nents ⇒ page 375
3 - Exhaust gas temperature
sender 1 - G235-
❑ Summary of compo‐
nents ⇒ page 370
4 - Exhaust gas temperature
sender 2 - G448-
❑ only for vehicles with en‐
gine identification char‐
acters CRKB
❑ Summary of compo‐
nents ⇒ page 370
❑ Electrical plug connec‐
tion for exhaust gas
temperature sender 2 -
G448- ⇒ page 289
5 - lambda probe - G39- with
heating for lambda probe - Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Z19- unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ Summary of compo‐
nents ⇒ page 370
❑ electrical plug connec‐
tion for Lambda probe -
G39- ⇒ page 289
6 - Exhaust gas temperature
sender 3 - G495-
❑ Summary of compo‐
nents ⇒ page 370
❑ Electrical plug connection for exhaust gas temperature sender 3 - G495- ⇒ page 289
7 - Exhaust gas temperature sender 4 - G648-
❑ Summary of components ⇒ page 370
❑ Electrical plug connection for exhaust gas temperature sender 4 - G648- ⇒ page 289
8 - Lambda probe downstream of catalytic converter - G130- with heating for lambda probe - Z29-
❑ only for vehicles with engine identification characters CRKB
❑ Summary of components ⇒ page 370
❑ electrical plug connection for lambda probe downstream of catalytic converter - G130- ⇒ page 292
9 - Heating backup pump - V488-
❑ Summary of components ⇒ page 149

1. Diesel direct injection system - fitting location, system overview 291

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Fitting location of electrical plug connection for Lambda probe af‐

ter catalytic converter - G130- (only for vehicles with engine
identification characters CRKB)
• Below the left centre console -arrow-.

1.2 Schematic overview - fuel system

Note

♦ Red = fuel feed line

♦ Blue = fuel return line
♦ The arrows point in the fuel flow direction.

1 - Fuel filter
❑ Summary of compo‐
nents ⇒ page 196
2 - High pressure pump
❑ Summary of compo‐
nents ⇒ page 309
3 - Fuel dosage valve - N290-
4 - Fuel temperature sender -
G81-
5 - Fuel pressure sender -
G247-
❑ Summary of compo‐
nents ⇒ page 297
6 - Fuel distributor
❑ Summary of compo‐
nents ⇒ page 297
7 - Control valve for fuel pres‐
sure - N276-
❑ Summary of compo‐
nents ⇒ page 297
8 - Injection units
❑ Summary of compo‐
nents ⇒ page 295
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
9 - Fuel tank Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ with fuel pump for pre‐ unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
delivery - G6-
❑ Summary of compo‐
nents ⇒ page 185

292 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 - Choke

1.3 Filling/bleeding the fuel system

Caution

In order to prevent the high pressure pump from running dry

(very narrow tolerances) and to achieve a quick engine start
after parts are replaced, the following must be observed:
♦ If fuel system between tank and pump parts/components
have been removed or replaced the fuel system must be
filled/bled before the engine is started up for the first time.

In order to fill up the high pressure pump with fuel, proceed as

follows:
• Vehicle must be refuelled.
– Connect vehicle diagnosis tester and switch on ignition sys‐
tem.
– Perform Targeted Function Activate fuel delivery
unit , bleed fuel system .

• The fuel pump activates.

• The fuel pump must run for approximately 3 minutes to ensure
that the pump is sufficiently filled with fuel.
– After filling the fuel system, start the engine.
– Run the engine at medium speed for several minutes, then
turn it off again.
– Test fuel system for tightness ⇒ page 293 .
– Delete event memory entry with Vehicle diagnosis tester .
– Then conduct test drive with at least one full load acceleration.
– Then check high-pressure area again for tightness.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Note with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

If there is still air in the fuel system the engine may enter dry-
running operation during the test drive. Switch off engine and
delete the event memory. Then continue the test drive.

– Delete event memory entry with Vehicle diagnosis tester .

1.4 Check the fuel system for tightness

– Let the engine run at idling speed for a few minutes.
– Carry out a visual inspection of the complete fuel system for
leaks after switching off the engine.
If there is leakage despite the correct tightening torque:
– Replace the affected component part and repeat the test se‐
quence.
If no leaks are found:
– Carry out a test drive with minimum one full load acceleration
up to max. speed.

1. Diesel direct injection system - fitting location, system overview 293

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Then once again carry out a visual inspection of the complete

fuel system for leaks.

294 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Injection units/fuel distributor

2.1 Summary of components - injection units (injectors)

1 - Sealing ring
❑ in the cylinder head cov‐
er
❑ replace after removal
⇒ page 80
2 - Copper disc
❑ replace after removal
3 - O-ring
❑ replace after removal
4 - Injection unit
❑ removed injection units,
high pressure lines and
clamping claws to be re-
installed must only be
mounted again at the
same cylinder.
❑ removing and installing
⇒ page 303
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
5 - O-ring
❑ replace after removal
6 - Fuel return line
❑ to fuel tank
❑ must not be kinked,
damaged or blocked
❑ do not disassemble
❑ fill/bleed fuel system af‐
ter exchange
⇒ page 293 .

2. Injection units/fuel distributor 295

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

7 - Clamping claw

Caution
Risk of engine damage!
When
♦ installing a new
engine without attached
parts it is imperative to
tighten the clamping
claws of the injection
units to the specified
tightening torque
-Pos. 8- - after installing
the high pressure lines
⇒ Item 8 (page 296) for
alignment of the injection
units when installing the
high pressure lines the
clamping claws must be
tightened »hand-tight on‐
ly« after delivery.

❑ removed injection units and clamping claws to be re-installed must only be mounted again at the same
cylinder.
❑ Fitting position ⇒ page 296
8 - 9 Nm + torque a further 180° (1/2 turn)
❑ replace after removal
9 - High pressure line, 28 Nm
❑ between fuel distributor and injection units
❑ follow all instructions for installation of high pressure lines
⇒ “2.9.2 Installing high pressure line”, page 306
❑ install free of stress
10 - Grommet
❑ in the cylinder head cover
❑ Renew if damaged.

Fitting position of the clamping claw

• One clamping claw has 2 injection units.
• The clamping claw gasket -arrow- points downwards.

296 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.2 Fuel distributor - summary of components

1 - Fuel pressure sender -

G247- , 100 Nm
❑ removing and installing
⇒ page 317
❑ Reuse possible
⇒ page 317
2 - High pressure line, 28 Nm
❑ between fuel distributor
and injection units
❑ follow all instructions for
installation of high pres‐
sure lines
⇒ “2.9.2 Installing high
pressure line”,
page 306
3 - Fuel distributor
❑ removing and installing
⇒ page 307
4 - 20 Nm
5 - O-ring
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ replace after removal
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

6 - Fuel pressure regulating

valve - N276- , 80 Nm
❑ Renew. ⇒ page 316 .
❑ replace after each re‐
moval
❑ Re-adjust after replac‐
ing the learning values
in “Targeted Functions”
⇒ Vehicle diagnostic
tester
7 - Fuel return-flow hose
8 - Fuel return-flow line
9 - 8 Nm
10 - High pressure line, 28 Nm
❑ between the high pressure pump and the fuel distributor
❑ follow all instructions for installation of high pressure lines
⇒ “2.9.2 Installing high pressure line”, page 306
11 - 8 Nm

2.3 Check injection units

There are 3 ways to check the injection units.
♦ ⇒ “2.4 Adjust the correction values for injection units”,
page 298
♦ ⇒ “2.5 Check injection unit return quantity with engine run‐
ning”, page 298
♦ ⇒ “2.6 Check injection unit return flow quantity at starter
speed”, page 300

2. Injection units/fuel distributor 297

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.4 Adjust the correction values for injection

units
♦ The “injector quantity adjustment (IQA)” functionality has the
task of correcting the injection quantity individually for each
cylinder of a common rail system in the entire map range.
♦ The 7-digit adjustment values are printed on each injection
unit. The printed values may be letters and/or digits.

View from the top of the injection unit

1- Adjustment value (checksum; information in the image is
only an example)
2- Data Matrix Code
3- Part number
♦ After replacement of an injection unit the adjustment value
must be written to the engine control unit.
♦ After replacement of the engine control unit the “injection unit
adjustment values” must be transferred to the new engine
control unit.
♦ In addition, check all other “injector quantity adjustment (IQA)”
injection units to ensure that all values have been entered cor‐
rectly. If the correct values are stored in the engine control unit,
these values must never be entered again.
♦ The work procedure for the adaptation is described in the
“Targeted fault finding”. (The work sequence is also described
in “Targeted Functions”.) ⇒ Vehicle diagnostic tester.

2.5 Check injection unit return quantity with

engine running
A - Check return quantity of all injection units
Special tools and workshop equipment required
♦ Measuring vessel, fuel test
Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

298 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect hose connection -2- at the fuel feed line.

– Close the return-flow line connection with a blind plug -1-.
– Keep fuel return-flow hose -2- (extend if necessary) in a meas‐
uring vessel to measure the overall return flow quantity.
– Start engine and run in idle for 2 minutes.
• Specified value in 2 minutes: 0 ml to 50 ml
– If the specified value is reached, increase engine rpm to 2000
to 2500 rpm for 2 minutes, then check the return flow quantity.
• Specified value in 2 minutes: less than 250 ml
If the specified value is exceeded, this indicates that there is one
(or more) defective fuel injection unit(s). Check the return flow
quantity of each individual injection unit
B - Check return quantity of the individual injection units

Special tools and workshop equipment required

♦ Hose clamps up to ∅ 25 mm - MP7-602 (3094)-
♦ Return flow quantity measuring device - VAS 6684-
Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

Note

Each injection unit has a small fuel return-flow quantity. If this re‐
turn flow quantity is relatively great (in relation to the return flow
quantity of the other injection units), this injection unit is probably
defective.

– Before removing, clean all return flow connections (for exam‐

ple with a commercially available cold cleaner).
– Dry all cleaned parts.
– Pinch of coolant hose -arrow- using a hose clamp of up to 25
mm - MP7-602 (3094)- .
– Remove noise insulation.

2. Injection units/fuel distributor 299

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Pull off return-flow line connections on injection unit by pulling

release buttons upwards -arrows-.

Note

Pay attention to cleanliness; no dirt must get into the removed

return lines and the connections of the injection units.

– Firmly fit adapter C6 to the return-flow line connections of all

4 injection units.
– Connect hose lines of the return flow quantity measuring de‐
vice - VAS 6684- to the adapter.
– Start engine and run in idle for a few minutes.

Caution

Risk of damage to injection units when return-flow lines are

removed.
♦ No acceleration must occur during testing - the engine
must run in idle.

– When the engine is at operating temperature while the engine

is idling there must be only minimal difference in the return flow
quantity of all 4 return-flow lines (example -1-).
– If one injection unit has
unless authorised by a significantly higherAUTO
AUTO A. S. ŠKODA return
A. S. flow quan‐
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
ŠKODA does not guarantee or accept any liability
tity (example with-2-), this
respect injection
to the correctnessunit must inbethisreplaced
of information document. Copyright by ŠKODA AUTO A. S.�
⇒ page 303 .
Assembly of fuel feed lines
– Carefully press the connections of the return-flow lines onto
the injection units. The cap must click audibly into place, af‐
terwards carefully press the unlocking bolt downwards.
– Check fuel system for tightness ⇒ page 293 .

2.6 Check injection unit return flow quantity

at starter speed

Note

If the engine will not start the return flow quantity of the injection
units can also be tested at starter speed.

Special tools and workshop equipment required

♦ Return flow quantity measuring device - VAS 6684-
Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

300 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

– Remove engine cover at the top ⇒ page 9 .

– Before removing, clean all return flow connections (for exam‐
ple with a commercially available cold cleaner).
– Dry all cleaned parts.
– Remove noise insulation.
– Pull return-flow line connections of the injection units - to do
so, pull the bracket upwards -arrows-.

Note

Pay attention to cleanliness; no dirt must get into the removed

return lines and the connections of the injection units.

– Disconnect electrical plug connection -2- at the fuel pressure

control valve - N276- -Pos. 1-.

Note

This prevents fuel from being injected during the start attempt.

– Firmly fit adapter C6 to the return-flow line connections of all

4 injection units.
– Connect hose lines of the return flow quantity measuring de‐
vice - VAS 6684- to the adapter.
– Actuate the starter 3 times (leave a pause of 20 seconds be‐
tween each start attempt - starter overheating protection).
• Specified value of the return flow quantity: 0 ml
– If fuel is leaking from one fuel injection unit, that injection unit
must be replaced.
– Put the electrical plug connection from the fuel pressure con‐
trol valve - N276- back in place.
Assembly of fuel feed lines
– Press connections of return-flow lines onto the injection units
until they audibly locks into place.
– Then press
Protected the brackets
by copyright. Copying for down
private oron both sides.
commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Check fuel system
with respect for tightness
to the correctness of information⇒
in page 293 Copyright
this document. . by ŠKODA AUTO A. S.�

– Interrogating and erasing fault memory of engine control unit

⇒ Vehicle diagnostic tester.

2. Injection units/fuel distributor 301

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.7 Carry out the vacuum test of the injec‐

tion units
Special tools and workshop equipment required
♦ Hand vacuum pump , e.g. -VAS 6213-
♦ Adapter C6 from return quantity measuring device - VAS
6684-
Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Delete event memory entry with vehicle diagnosis tester ⇒ Ve‐

hicle diagnostic tester.
– Remove engine cover at the top ⇒ page 9 .
– Before removing, clean all connections (for example with a
commercially available cold cleaner).

Note

♦ Pay attention to cleanliness, no dirt must get into the fuel sys‐
tem.
♦ Check cylinders one after another.

– Dry all cleaned parts.

Start with cylinder 1.
– Remove noise insulation.
– Pull off return-flow line connections on injection unit by pulling
release buttons upwards -arrows-.

302 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect the clean, blown through adapter on the injection unit

to be tested.
– A vacuum of -500 mbar is built up using the hand vacuum
pump - VAS 6213- .
If the injection units ar O.K, the vacuum remains constant for more
than 30 s.
If the injection units are defective, the vacuum drops within 2 ... 3
s to 0 bar.
If necessary repeat the test, pay attention to the vacuum loss on
the hand vacuum pump - VAS 6213- .
– Replace injection units ⇒ page 303 .

2.8 Removing and installing the injection

units
Special tools and workshop equipment required
♦ Extractor - T10055-
♦ Assembly sleeve - T10377-
♦ Extractor - T10415-
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

– Remove noise insulation. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Pull off return-flow line connections on injection unit by pulling
release buttons upwards -arrows-.

– Disconnect electrical plug connections -arrows- at the glow

plugs.

Note

Each clamping claw secures 2 injection valves and can only be

removed when both injection units are »removed«.

– Unscrew union nuts of the respective high pressure lines

-1…4- and pull off the corresponding high pressure lines.
– Close open lines and connections with blind plugs.

2. Injection units/fuel distributor 303

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screw -1- and remove clamping claws.

• Order for injection unit expansion: First remove injection unit
on cylinder “2” and then on cylinder “1”, on cylinder “4” and
then on cylinder “3” respectively.
– Position extractor - T10055- with the extractor - T10415- as
shown in the illustration and pull out upwards.
– Remove the clamping screw before removing the injection
unit.

Note

To avoid damaging the sealing lip, use rotary motion to pull off
injection units.

– Place the removed injection units on a clean cloth.

Install

Caution

Risk of damage to injection unit sealing surfaces.

♦ To remove the soot particles on the sealing surface of the
injection unit, clean the injection unit shaft in the cylinder
head with cleaning set - VAS 6811- or with a cloth soaked
in engine oil. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Installing new injection units

When installing a new injection unit the following must be re‐
placed:
♦ Copper gasket
♦ O-ring for the injection unit shaft
♦ O-ring for fuel feed line connection
– Follow all instructions for installation of high pressure lines
⇒ “2.9.2 Installing high pressure line”, page 306 .
Installing used injection units
When reinstalling a used injection unit the following must be re‐
placed:
♦ Copper gasket
♦ O-ring for the injection unit shaft
♦ O-ring for fuel feed line connection
– Spray the tip of the injection unit with a rust solvent spray. Re‐
move soot particles or oil particles with a cloth after approxi‐
mately 5 minutes.
– For disassembling the old copper gasket ring from the injection
unit, carefully tighten the gasket ring in a vice until the copper
gasket ring is prevented from spinning between the chuck
jaws. Pull the injection unit out of the copper gasket ring with
slight turning and pulling movements of the hand.
– Clean the deposit below the copper sealing ring.

304 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Replace the gasket ring for the injection channel, for this step
use the assembly sleeve - T10377- .
Continuation for used and new injection units:
– Coat all O-rings with assembly oil, engine oil or diesel fuel be‐
fore installation.
– Install the injection units.
– First tighten the union nuts of the high pressure lines hand-
tight. Check that seating is free of tension.
– After replacement of one or more injection units the correction
values for the new injection units must be written to the engine
control unit ⇒ page 298 .
– Filling and bleeding the fuel system ⇒ page 293 .
Tightening torque
♦ Summary of components - injection units (injectors)
⇒ page 295 .

2.9 Removing and installing high pressure

lines

2.9.1 Remove high pressure line between fuel

distributor and the high pressure pump.
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

– Clean fuel line and line end with cold cleaner and blow dry with
compressed air.
– Release screw -1-.
– Unscrew union nuts -arrows- and remove high pressure line.

2. Injection units/fuel distributor 305

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2.9.2 Installing high pressure line

Special tools and workshop equipment required
♦ Tool insert SW 17
♦ Socket wrench insert - T40055-

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

Procedure

Note

♦ Clean fuel line and line end with cold cleaner before removal,
and blow dry with compressed air.
♦ Pay attention to the cylinder specific marking when re-using
the high pressure lines.
♦ The high pressure lines can be re-used after the following
tests:
♦ Check the sealing cone of the respective high pressure line for
deformations and cracks.
♦ The line borings must not be deformed,
Protected byconstricted orfordam‐
copyright. Copying private or commercial purposes, in part or in whole, is not permitted
aged. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Corroded lines must no longer be used.

Caution

Risk of line break because of high pressure line being under

tension.
♦ Loosen fuel distributor and clamps for improved, tension-
free positioning of injection lines. If necessary, move the
fuel distributor slightly and turn the corresponding injection
unit slightly. The lines must be never bent or twisted.

– Suction off dirt from the sealing cone at the fuel distributor.
– Moisten thread of the nut with clean engine oil.
– Hand-tighten union nuts, ensure that the fit is tension-free.
– To tighten the high pressure lines on the fuel distributor and
injection units, use torque wrench -1- with tool insert SW 17 or
socket wrench insert - T40055- .

306 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Set balancing weight -1- on the high-pressure lines as shown

in the diagram.
– Check fuel system for tightness ⇒ page 293 .
Tightening torques
♦ ⇒ “2.1 Summary of components - injection units (injectors)”,
page 295
♦ ⇒ “2.2 Fuel distributor - summary of components”, page 297

2.10 Removing and installing the fuel distrib‐

utor
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ pageunless
4 . authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove high pressure line between fuel distributor and the

high pressure pump ⇒ page 305 .
– Expose fuel return-flow hose -1-.
– Open holding clamps -arrows-, unclip and remove cable duct
-2-.

2. Injection units/fuel distributor 307

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connections:

1 - for fuel pressure sender - G247-
3 - for fuel pressure regulating valve - N276-
– Loosen hose clamp -4-, pull off fuel return-flow hose.
– Unscrew high pressure line union nuts -2-.
– Remove high pressure line and place it on a clean cloth.
– Screw out screws -arrows- and remove fuel distributor.
Install
Installation is carried out in the reverse order. When installing,
note the following:
– Follow all instructions for installation of high pressure lines
⇒ “2.9.2 Installing high pressure line”, page 306 .
Tightening torques
♦ Summary of components - injection units (injectors)
⇒ “2.1 Summary of components - injection units (injectors)”,
page 295
♦ Summary of components - fuel distributor
⇒ “2.2 Fuel distributor - summary of components”, page 297

308 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 High pressure pump

3.1 Summary of components - high pressure pump

1 - Bracket for auxiliary units

❑ removing and installing
⇒ page 39
2 - Bolt
❑ Qty. 3
❑ different lengths
❑ replace after removal
❑ Specified torque:
♦ short screw, 20 Nm + tor‐
que a further 45° (1/8 turn)
♦ long screw, 20 Nm + torque
a further 180° (1/2 turn)
3 - Toothed belt pulley high
pressure pump
4 - 95 Nm
❑ to release and tighten
use counterholder -
T10051-
5 - Hub
❑ to remove, use extractor
-T10489-
6 - High pressure pump
❑ with fuel dosage valve -
N290- (do not open)
❑ removing and installing
⇒ page 310

Caution
Risk of damage to the
high pressure pump
through running dry.
If♦the high pressure pump
is removed or replaced,
the fuel system must be
filled/bled before the en‐
gine is started for the first
time ⇒ page 293 .

❑ Re-adjust after replacing the learning values in “Targeted Functions” ⇒ Vehicle diagnostic tester
7 - Fuel intake hose
8Protected
- Fuelbyreturn-flow hose
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
9 -with
High pressure
respect line of information in this document. Copyright by ŠKODA AUTO A. S.�
to the correctness

❑ between fuel distributor and high pressure pump

❑ removing ⇒ page 305
❑ follow all instructions for installation of high pressure lines
⇒ “2.9.2 Installing high pressure line”, page 306

3. High pressure pump 309

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3.2 Removing and installing the high pres‐

sure pump
Special tools and workshop equipment required
♦ Counterholder - T10051-
♦ Extractor -T10489-
♦ Locking pin -T10492-
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

Caution

Risk of damage to the high pressure pump through running dry.

♦ If the high pressure pump is removed or replaced, the fuel
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
system must be filled/bled
with respect to before the ofengine
the correctness is instarted
information for Copyright by ŠKODA AUTO A. S.�
this document.
the first time ⇒ page 293 .

– Remove the toothed belt from the camshaft ⇒ page 47 .

– Remove high pressure line between fuel distributor and the
high pressure pump ⇒ page 305 .
– Place counterholder - T10051- at the high pressure pump
toothed belt pulley.
– Tighten nuts -arrow- hand tight.
– Pull off rig pin -T10492- , carefully turn high pressure pump
shaft in stress-free position.
– Unscrew nuts -arrow-, remove counterholder - T10051- .
– Remove the high pressure pump toothed belt pulley.

– Suspend extractor -T10489- at the hub by turning to the right.

– Remove the hub of the high pressure pump.

310 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove fuel return-flow hoses -2-.

– Separate electrical plug connection -1-.
– Unscrew screws -arrows-.
– Carefully remove the high pressure pump.
Install
Installation is carried out in the reverse order. When installing,
note the following:

– Place hub -arrow- on the high pressure pump shaft.

• The key on the high pressure pump shaft must engage into
the slot in the hub.

– Mount the toothed belt pulley onto the hub.

• There must not be any oil present between the counterholder
and the toothed belt pulley

– Turn nuts -arrow- to the thread of the high pressure pump

shaft. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Place counterholder on toothed
with respect to the correctness belt pulley
of information and tighten
in this document. nuts
Copyright by ŠKODA AUTO A. S.�
hand-tight -arrow-.
– Turn high pressure pump toothed belt pulley using the coun‐
terholder - T10051- until it can be locked with the rig pin -
T10492- .

3. High pressure pump 311

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– To do so, insert the rig pin -T10492- into fork -2- of the hub
and into the bore behind it -1- in the auxiliary units bracket.
– Loosen nuts -arrow- again.
• It must still be possible to just turn the high pressure pump
toothed belt pulley, however it must not hang loose.
– Installing the timing belt ⇒ page 49 .
– Installing high pressure line ⇒ page 306 .

Caution

Risk of damage to the high pressure pump through running dry.

♦ If the high pressure pump is removed or replaced, the fuel
system must be filled/bled before the engine is started for
the first time ⇒ page 293 .

– After replacing the high pressure pump, re-adjust the learning

values in “Targeted Functions” ⇒ Vehicle diagnostic tester.
♦ Tightening torques
⇒ “3.1 Summary of components - high pressure pump”, page
309

312 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4 Senders and sensors

4.1 Removing and installing intake air tem‐

perature sender - G42- / charge air tem‐
perature sender after charge air cooler -
G811-
Removing
– Remove engine cover ⇒ page 9 .
– Disconnect the electrical plug connection -1 or 2-.
1 - Charge air temperature sender after charge air cooler - G811-
2 - Intake air temperature sender - G42-
– Unscrew the corresponding charge air temperature sender.
Install
Installation is performed in the reverse order, pay attention to the
following points:
• Tightening torque ⇒ page 325 .

4.2 Removing and installing fuel tempera‐

ture sender - G81-
Removing
– Remove engine cover Protected
⇒ pageby 9copyright.
. Copying for private or commercial purposes, in part or in whole, is not permitted
– Separate electrical plug connection
respect to the -1-.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unscrew fuel temperature sender - G81- -arrow-.

Install
Installation is performed in the reverse order, pay attention to the
following points:
– Check fuel system for tightness ⇒ page 293 .

4.3 Removing and installing air flow mass

meter - G70-
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
– Remove engine cover ⇒ page 9 .

4. Senders and sensors 313

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect vacuum hoses on the air guide pipe -arrows-.

– Loosen hose clamps -1, 2-, remove intake hose.

– Release screw -1-.

– Turn the air mass meter - G70- - Pos. 2- in
-direction of arrow B- and remove.
Install
It is essential that the following work instructions be performed to
ensure perfect functioning of the air mass meter - G70- .

Note

♦ If the air filter is heavily soiled or soaked, dirt particles or mois‐

ture can enter the air mass meter and distort the measured air
flow values. This results in a reduction of output, because a
lower injection quantity is calculated.
♦ Always use an original air filter element.
♦ Always replace any damaged gasket rings (unmetered air).
♦ Use a silicone-free lubricant for installing the air guide hose
and gasket ring.
♦ The hose- and pipe supports and the air guide hoses must be
de-oiled and degreased before installing.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

– Check air mass meter as well as air guide hose (on the side
of the fresh air) for salt residues, dirt and leaves.
– Check suction channel up to air filter insert for dirt. if you find
it is dirty, remove salt residues, dirt and leaves from the air filter
housing (top and bottom section) (clean by washing or using
a vacuum as required).

– To install, position the air mass meter - G70- - Pos. 2- and turn
in the -direction of arrow A-.
Tightening torques
♦ Summary of components - air filter ⇒ page 332

314 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.4 Check fuel pressure regulating valve -

N276-
Special tools and workshop equipment required
♦ Suitable auxiliary hose for connection to the fuel return-flow
line
♦ Fuel tank, approx. 200 ml
Procedure

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

– Loosen hose clamp -arrow-, remove fuel return-flow hose from
the fuel distributor.
– Close the return-flow line connection with a blind plug.

4. Senders and sensors 315

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect an auxiliary hose -3- to the fuel distributor return hose

-2-.
– Hold this hose line -3- in a suitable vessel in order to measure
the return flow quantity.
1) Test with engine running
– Start engine and run at idling speed.
• Specified value: greater than 75 ml in 30 seconds
If the specified value is not reached, the fuel pressure regulating
valve - N276- is defective.
2) Test with engine running
If the condition under point 1) is fulfilled, increase the engine
speed to ≥ 2000 rpm.
• Return flow quantity specified value: 0 ml
• A drop-leakage is permissible
If the specified value is not reached, the fuel pressure regulating
valve - N276- is defective.
3) The engine will no longer start
Perform test at starter speed.
• Return flow quantity specified value: 0 ml
• A drop-leakage is permissible
If the specified value is not reached, the fuel pressure regulating
valve - N276- is defective.
– Replace fuel pressure regulating valve - N276- ⇒ page 316 .

4.5 Replace fuel pressure regulating valve -

N276-
The fuel pressure regulating valve - N276- is located on the fuel
distributor and provides a constant pressure in the fuel distributor
and in the injection lines (fuel high pressure circuit).
The regulating valve opens if there is too high a pressure in the
fuel high pressure circuit so that one part of the fuel from the fuel
distributor returns to the fuel tank via a return-flow line.
The pressure control valve closes if there is too low a pressure in
the high-pressure fuel circuit and thus seals the high-pressure
side from the low-pressure side.

Note

The fuel pressure regulating valve - N276- is not reusable.

Special tools and workshop equipment required

♦ Cleaning and degreasing agent , e.g. -D 009 401 04-
♦ Protective goggles and gloves
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Open-end wrench SW 30 unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

316 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

– Expose fuel return-flow hose -1-.
– Open holding clamps -arrows-, unclip and remove cable duct
-2-.
– Before removing, clean the threaded area of the fuel pressure
regulating valve - N276- .
• No dirt must get into the hole of the fuel distributor.
• No cleaning agent must get into the plug connection, clean
carefully.
– Dry fuel pressure regulating valve - N276-

– Separate electrical plug connection -2-.

– Loosen union nuts -1- - to do so, hold on hexagon against the
fuel distributor. Afterwards release by hand.
– Suction the dirt out ofunless
the fuel distributor hole (thread and con‐
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
tact surface). To do so with
do respect
not useto theany mechanical
correctness tools.
of information in this document. Copyright by ŠKODA AUTO A. S.�

– Close the open port on the fuel rail with a clean plugs.
Install
• Tightening torque
⇒ “2.2 Fuel distributor - summary of components”, page 297

Note

♦ Replace the fuel pressure regulating valve - N276- each time

it is removed.
♦ Moisten the threaded insert and the biting edge of the fuel
pressure regulating valve - N276- with diesel fuel.

– Tighten the union nut by hand.

– Align the new control valve so that the connecting cable is re-
installed free of tension after the plug has been repositioned.
– Counterhold housing hexagon of the regulating valve in this
position using a wrench or pliers (such as water pump pliers).
– To tighten the union nuts use a suitable torque wrench with an
open-end wrench (size 30).
– Filling and bleeding the fuel system ⇒ page 293 .

4.6 Removing and installing fuel pressure

sender - G247-
Special tools and workshop equipment required
♦ Socket insert size 27 - T40218-

4. Senders and sensors 317

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

♦ Cleaning and degreasing agent , e.g. -D 009 401 04-

♦ Protective goggles and gloves
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove engine cover at the top ⇒ page 9 .

WARNING

Wear protective gloves and protective googles when working

with grease remover!

– Before removing, clean the thread area around the fuel pres‐
sure sender - G247- with a grease remover (no dirt must get
into the hole of the fuel distributor).

Note

No grease remover must get into the plug connection, carefully

clean.

– Dry the fuel pressure sender - G247- .

318 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Separate electrical plug connection -2-.

– Unscrew the fuel pressure sender - G247- with the socket in‐
sert size 27 - T40218- .
– Suction the dirt out of the fuel distributor hole (thread and con‐
tact surface). To do so do not use any mechanical tools.

Note

Close the fuel distributor hole immediately with a suitable screw

plug in order to prevent dirt from penetrating.

Install

Note

♦ Pay attention to damage of the sealing surfaces (biting edge

seal) and the thread of the new fuel pressure sender - G247- .
It is possible to use the fuel pressure sender - G247- again.
♦ Also check the sealing surface in the hole of the fuel distributor.
♦ Coat the threaded insert and biting edge of the fuel pressure
sender - G247- with Diesel fuel.

– Tighten the fuel pressure sender - G247- by hand.

– Tighten the sender:
♦ Specified torque: ⇒ page 297 .
– Filling and bleeding the fuel system ⇒ page 293 .
• Tightening torque
⇒ “2.2 Fuel distributor - summary of components”, page 297

4.7 Removing and installing differential

pressure sender - G505-

Note

The differential pressure sender - G505- determines the loading

statuts of the particle filter.

Removing
– Remove engine cover at the top ⇒ page 9 .

4. Senders and sensors 319

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open heat protection sleeve -1-.

– Separate electrical plug connection -4-.
– Unscrew screw -3-, remove differential pressure sender -
G505- from the holder.
– Spray hose with a solvent at charge pressure sender - G505-
before removing it.
– Loosen hose clamp -2-.
– Disconnect hose carefully and straight from the connection fit‐
tings (the connection fittings move slightly out of the differential
pressure sender - G505- ).
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Blow out control lines of the differential pressure sender -

G505- to the particle filter with compressed air before instal‐
lation in particle filter direction (it may by
unless authorised beŠKODA
blockedAUTOor iced
A. S. up AUTO
ŠKODA by A. S. does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

condensation water). with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Pay attention to the tight connection and leaktightness of the

hose.
♦ Only install approved spring strap clips for securing the hose
connections ⇒ ETKA - Electronic Catalogue of Original Parts .

– After replacing the differential pressure sender - G505- , an

adaption must be performed in the function “Targeted func‐
tions ” ⇒ Vehicle diagnostic tester.
Tightening torques
• Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370
• Summary of components - exhaust gas cleaning
⇒ page 357

4.8 Removing and installing pressure sen‐

sor for exhaust gas 1 - G450-
Removing
– Remove engine cover ⇒ page 9 .

320 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open heat protection sleeve -1-.

– Separate electrical plug connection -8-.
– Unscrew screw -2-, lightly press the differential pressure send‐
er - G505- -3- to one side.
– Separate electrical plug connection -6-.
– Release screw -4-.
– Spray hoses on the pressure sensor 1 for exhaust gas - G450-
-5- with a solvent before removal.
– Loosen hose clamps -7-.

Caution

Risk of destruction of the pressure sensor as a result of the

connection fitting breaking.
♦ Pull hoses off carefully and straight from the connection
fitting.

Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

♦ Blow out control lines of the differential pressure sender -

G450- to the particle filter with compressed air before instal‐
lation in particle filter direction (it may be blocked or iced up by
condensation water).
♦ Pay attention to the tight connection and leaktightness of the
hose.
♦ Only install approved spring strap clips for securing the hose
connections ⇒ ETKA - Electronic Catalogue of Original Parts .

– After replacing the pressure sensor 1 for exhaust gas - G450-

the adapted values must be set in the function “Targeted
functions” ⇒ Vehicle diagnostic tester.
Tightening torques
• Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370

4. Senders and sensors 321

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

5 Lambda probe

5.1 Lambda probe - Summary of components

1 - Lambda probe downstream

of catalytic converter - G130-
with heating for lambda probe
- Z29- , 52 Nm
❑ only for vehicles with en‐
gine identification char‐
acters CRKB
❑ removing and installing
⇒ page 323
❑ Observe mounting in‐
structions ⇒ page 323
2 - Exhaust gas temperature
sender 4 - G648-
❑ removing and installing
⇒ page 372
❑ the thread of the ex‐
haust gas temperature
sender is coated and
must not be coated ad‐
ditionally with hot bolt
paste
3 - Exhaust gas temperature
sender 1 - G235-
❑ removing and installing
⇒ page 371
❑ Coat threads with hot
bolt paste; hot bolt paste
⇒ ETKA - Electronic
Catalogue of Original
Parts
4 - Exhaust gas temperature
sender 2 - G448-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ only for vehicles with en‐ unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
gine identification char‐ with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
acters CRKB
❑ removing and installing
⇒ page 373
5 - 8 Nm
6 - Differential pressure sender - G505-
❑ removing and installing ⇒ page 319
7 - Support
8 - Exhaust gas pressure sensor 1 - G450-
❑ only for vehicles with engine identification characters CRKB
❑ removing and installing ⇒ page 320
9 - 8 Nm
10 - Exhaust gas temperature sender 3 - G495-
❑ removing and installing ⇒ page 372
❑ the thread of the exhaust gas temperature sender is coated and must not be coated additionally with hot
bolt paste

322 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

11 - Lambda probe - G39- with heating for lambda probe - Z19- , 55 Nm

❑ removing and installing ⇒ page 323
12 - Exhaust gas cleaner

5.2 Removing and installing Lambda probe

- G39-
Special tools and workshop equipment required
♦ Extension piece (No. 22) - T10491-
Removing
– Remove engine cover ⇒ page 9 .
– Take the electrical plug connection -4- for Lambda probe -
G39- out of its holder and disconnect, expose the electric
cable.

– Unscrew lambda probe - G39- -arrow- with extension (No. 22)

- T10491- .
Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

♦ New lambda probes are coated with an assembly paste; the

paste is not allowed to reach to slots on the body of the probe.
♦ For a re-used lambda probe, only coat the thread with hot bolt
paste . This paste must not come into contact with the slots of
the lambda probe body.
♦ The electrical wiring of the lambda probe must be attached to
the same position when installing. This prevents the lambda
probe cable from coming into contact with the exhaust pipe.

Tightening torques
♦ Lambda probe - Summary of components ⇒ page 322 .

5.3 Removing and installing Lambda probe

after catalytic converter - G130-
Special tools and workshop equipment required
♦ Socket insert for Lambda probe - 3337-
Removing
– Remove the sound dampening systems and tunnel cover ⇒
Body Work; Rep. gr. 50 .

5. Lambda probe 323

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove the right underfloor trim panel ⇒ Body Work; Rep.

gr. 50 .
– Take the electrical plug connection -arrow- for Lambda probe
after catalytic converter - G130- out of its holder and discon‐
nect, expose the electric cable.

– Unscrew the lambda probe after catalytic converter - G130-

-arrow- with a socket wrench from the Socket insert for Lamb‐
da probe - 3337- .
Install
Installation is performed in the reverse order, pay attention to the
following points:

Note

♦ New lambda probes are coated with an assembly paste; the

paste is not allowed to reach to slots on the body of the probe.
♦ For a re-used lambda probe, only coat the thread with hot bolt
paste . This paste must not come into contact with the slots of
the lambda probe
Protected body.Copying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ The electrical wiring
with respect to theof the lambda
correctness probe
of information must
in this be attached
document. to
Copyright by ŠKODA AUTO A. S.�
the same position when installing. This prevents the lambda
probe cable from coming into contact with the exhaust pipe.

Tightening torques
♦ Lambda probe - Summary of components ⇒ page 322 .
♦ Sound dampening system - Summary of components ⇒ Body
Work; Rep. gr. 50 .
♦ Underfloor trim panel - Summary of components ⇒ Body
Work; Rep. gr. 50 .

324 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

6 Intake manifold, air filter

6.1 Assembly overview - intake manifold

1 - Sealing ring
❑ replace after removal
2 - Fit pin
3 - 8 Nm
4 - Seal
❑ replace after removal
5 - Screw
❑ Tightening torque and
tightening order
⇒ page 327
6 - Support
❑ for the intake manifold
❑ Tightening torque and
tightening order
⇒ page 327
7 - Screw
❑ Tightening torque and
tightening order
⇒ page 327
8 - Screw
❑ replace after removal
❑ Tightening torque and
tightening order
⇒ page 326
9 - Fit pin
10 - 8 Nm
11 - Intake manifold with
charge air cooler
❑ The intake manifold and
charge air cooler form a
single building unit
❑ removing and installing ⇒ page 329
12 - Screw
❑ replace after removal
❑ Tightening torque and tightening order ⇒ page 326
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
13 - Charge air temperature sender after charge
unless authorised by ŠKODA airAUTO
cooler - G811-
A. S. ŠKODA AUTO , 22
A. S.Nm
does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ removing and installing ⇒ page 313
14 - Seal
❑ replace after removal
15 - Inlet connections
❑ for throttle valve control unit - J338-
16 - Intake air temperature sender - G42- , 22 Nm
❑ removing and installing ⇒ page 313

6. Intake manifold, air filter 325

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

17 - 10 Nm
18 - Coolant pipe
19 - 10 Nm
20 - Coolant pipe
21 - O-rings
❑ replace after removal
22 - Throttle valve control unit - J338-
❑ With throttle valve potentiometer - G69-
❑ removing and installing ⇒ page 327
23 - O-ring
❑ replace after removal
24 - Air guide pipe
25 - Bolt
❑ Tightening torque ⇒ page 282
26 - Bracket
❑ for throttle valve control unit - J338-
❑ Tightening torque and tightening order ⇒ page 327
27 - Screw
❑ Tightening torque and tightening order ⇒ page 327
28 - Screw
❑ Tightening torque and tightening order ⇒ page 327

Intake manifold with charge air cooler - tightening torque and

tightening order
– Tighten screws in steps:
Stage Screws Tightening torque
1. -1…10- by hand as far as the stop
2. -1…10- tighten to 20 Nm
Protected -1…10- turnfor90°
by copyright. Copying further
private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

326 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Mounting bracket for intake manifold and mounting bracket for

throttle flap control unit - tightening torque and -sequence
– Tighten screws in steps:

WARNING

When installing the mounting bracket for the intake manifold

and, where necessary, the throttle flap control unit, ensure that
the appropriate bracket is not screwed into place under tension
or at an angle- crucial.

Stage Nuts and Tightening torque

bolts
1. -2, 3, 4, 7- firmly by hand as far as the stop
2. -2, 3, 4, 7- tighten to 20 Nm
3. -5- tighten to 10 Nm
4. -1- tighten to 10 Nm

6.2 Removing and installing the throttle

valve control unit - J338-
Special tools and workshop equipment required
♦ Hose clamps up to ∅ 25 mm - MP7-602 (3094)-
♦ Hose clip pliers - VAS 6362-
Removing
– Remove engine cover at the top ⇒ page 9 .
– Remove air filter housing
⇒ “6.5 RemovingProtected
and installing
by copyright. air filter”,
Copying page
for private 334 . purposes, in part or in whole, is not permitted
or commercial
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Release screw leftwith
and right
respect -arrow-.
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Unclip and remove bottom part -1- of air guide.

– Unscrew screws -arrows-.

– Loosen hose clamp -2-, remove air guide pipe -1-.
For vehicles with engine identification characters CLHA, CLHB,
CKFB, CKFC, CUPA, CRVC

6. Intake manifold, air filter 327

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -arrows-.

– Unclamp coolant hose -1- and -4- with hose clamps to 25 mm
- MP7-602 (3094)- .

Note

Place a cloth below to absorb leaking coolant.

– Loosen hose clamps -2, 3-, remove coolant hoses.

For vehicles with engine identification characters CRKB

– Release screws -arrows-.

– Unclamp coolant hose -1- and -5- with hose clamps to 25 mm
- MP7-602 (3094)- .

Note

Place a cloth below to absorb leaking coolant.

– Loosen hose clamps -2, 3, 4-, remove coolant hoses.

– Release screw -3-.

Note

-Ignore positions 1, 2-.

Continued for all vehicles

328 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connections:

2 - for Intake air temperature sender - G42-
3 - for throttle valve control unit - J338-
– Loosen hose clamp -4-, remove air guide hose.
– Unscrew screws -1-, remove connection fittings with throttle
valve control unit - J338- .
Install
Installation is carried out in the reverse order. When installing,
note the following:
• Tightening torque
⇒ “6.1 Assembly overview - intake manifold”, page 325 .

Note

Replace gasket and O-ring.

– When attaching the inlet connection to the throttle valve con‐

trol unit - J338- , pay attention to the fit pins.
– Install the front top coolant pipe ⇒ page 157 .
– Install air filter ⇒ page 334 .

6.3 Removing and installing intake manifold

The intake manifold and charge air cooler form a single building
unit.

Special tools and workshop equipment required

♦ Hose clip pliers - VAS 6362-
♦ Socket insert XZN 10 - T10501-
Removing

Note

♦ Safety precautions when working on the fuel supply system

⇒ page 4 .
♦ Observe rules for cleanliness ⇒ page 6 .

– Remove front top coolant pipe ⇒ page 157 .

– Remove high pressure line ⇒ page 305 .
– Remove air filter ⇒ page 334 .

6. Intake manifold, air filter 329

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew screws -arrows-.

– Loosen hose clamp -2-, remove air guide pipe -1-.

– Separate electrical plug connection -4-.

– Loosen hose clamps -1, 2-, remove fuel hoses.
– Unscrew screws -3-, lay fuel lines towards the rear.

– Unlock catch -arrow-, remove vacuum hose -1-.

– Unscrew screw -3-, remove vacuum hose -2-.
For vehicles with engine identification characters CRKB
– Removing the cover for the radiator fan ⇒ page 177 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Separate electrical plug connection -1-.

– Loosen hose clamp -2-.
Continued for all vehicles

330 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect and expose electrical plug connections:

1 - for charge air temperature sender after charge air cooler -
G811-
3 - for charge pressure sender - G31-
4 - for Intake air temperature sender - G42-
5 - for throttle valve control unit - J338-
– Unscrew hose clamps -2, 7-, remove coolant hose -6-.

– Release screw -1- for guide pipe for oil dipstick.

– Unscrew nuts -5- and remove the mounting bracket -6- from
the double screw -4-.
– Release screws -4, 7-.
– Unscrew screws -2, 3- for intake manifold holder.

– Unscrew screws -10…1- with the Polydrive socket XZN 10 -

T10501- , remove the intake
Protectedmanifold
by copyright.with charge
Copying for privateair cooler. purposes, in part or in whole, is not permitted
or commercial
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Install
– Place the new cylinder head gasket onto the fitted pins.

WARNING

Do not damage the sealing surface of the intake manifold when

placing it onto the fitted pins.

6. Intake manifold, air filter 331

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Tighten screws -1…10- as per the tightening torques and -

sequence
⇒ Fig. ““Intake manifold with charge air cooler - tightening tor‐
que and tightening order”“ , page 326 .
Continued installation is carried out in the reverse order. When
installing, note the following:

Note

Replace gasket.

– Install air filter ⇒ page 334 .

– Installing high pressure line ⇒ page 306 .
– Install the front top coolant pipe ⇒ page 157 .
Tightening torques
♦ Hose connections with screw clamps ⇒ page 281
♦ Intake manifold - Summary of components
⇒ “6.1 Assembly overview - intake manifold”, page 325 .
♦ Summary of components - removing and installing parts of the
lubrication system ⇒ page 116

6.4 Summary of components - air filter

332 Rep. gr.23 - Mixture preparation - injection

1 - Air deflector
❑ on the air filter lower part
2 - 2 Nm
3 - Air guide lower part
❑ on the lock support
4 - air guide pipe top
❑ on the lock support
5 - Cover
❑ for air guide
6 - 2 Nm
7 - 1.5 Nm
8 - Air filter upper part
❑ remove mechanical
contaminations
9 - Breather hose
❑ from charge pressure
control solenoid valve -
N75-
10 - Spring strap clamp
11 - Intake hose
12 - Screw clamp
❑ installing ⇒ page 281
13 - 1.5 Nm
14 - Air mass meter - G70-
removing and installing
⇒ page 313

15 - O-ring
❑ Renew if damaged.
16 - Air filter element
❑ pay attention to change intervals ⇒ Maintenance ; Booklet Octavia III
17 - Insert
❑ for air filter lower part

unless18 - Air filter lower part

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ remove mechanical contaminations
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

19 - Rubber pads
20 - O-ring
❑ Renew if damaged.
21 - Water drain hose
❑ with valve
❑ clean

6. Intake manifold, air filter 333

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

6.5 Removing and installing air filter

Removing
– Release screws -1, 3-.
– Unlock catch -arrows-, remove cover-2-.

– Expose coolant hose -2-.

– Unlock catches -arrows-, remove air guide pipe upper part
-1-.

– Disconnect the plug connection -2- at the air mass meter -

G70- .
– Disconnect vacuum hose -4-.
– Loosen hose clamp -3-, remove extraction hose.
– Remove air filter -1-.
Install
Installation is carried out in the reverse order. When installing,
note the following:
♦ Tightening torque ⇒ page 332

Note
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
♦ Connections,
with respect tocharge air pipes
the correctness and hoses
of information of charge
in this document. airbysystem
Copyright ŠKODA AUTO A. S.�
must be free of oil and grease before being installed.
♦ Use a silicone lubricant to assemble the suction hose.
♦ Only install approved spring strap clips for securing the hose
connections ⇒ ETKA - Electronic Catalogue of Original Parts .

334 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect water drainage hose -arrow-.

– Clean connection and air filter lower part and hose to remove
dirt and leaves.

– When attaching the suction nozzle to the air filter housing, pay
attention to the installation markings -arrows-.
– Put air filter onto the battery tray and push in until there is an
audible click.
– Press air filter down again and check by pulling that the air
filter is fully engaged.

6. Intake manifold, air filter 335

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

7 Engine control unit

7.1 Removing and installing engine control

unit - J623-
Removing

Note

♦ If the engine control unit is replaced, the must be ⇒ Vehicle

diagnostic tester connected and the function “replace engine
control unit” must be carried out.
♦ If the adjustment values of the injection units can no longer be
read from the old (defective) engine control unit, these adjust‐
ment values must be manually entered into the new engine
control unit and adapted to it.

WARNING

If the engine control unit touches the plus pole of the battery,
this will destroy the engine control unit.

– Unlock catch in -direction of the arrow- and remove the engine

control unit -1-.
– Unlock plug connections for engine control unit - J623- and
pull off.
Install
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Installation is carried out in reverse order.unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
After installing a new engine control unit, the following work step
must be performed:
– Activate engine control unit ⇒ Vehicle diagnostic tester.

7.2 Removing and installing engine control

unit - J623- , engine control unit with
protective housing
Removing
Special tools and workshop equipment required
♦ commercially available miniature grinder
♦ Hot air blower , e.g. -VAS 1978/14A- with push-on nozzle from
wiring harness repair set , e.g. -VAS 1978 B-

336 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

♦ If the engine control unit is replaced, the must be ⇒ Vehicle

Unscrew shear bolts -arrows- to remove the protective housing

-1- as follows:

– In the shear bolt head -1-, using a miniature grinder -2-, make
a slot for a screwdriver.

Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
♦ The threads of the pull-off screws are equipped with safety
agent. Warming the pull-off screw when grinding a slot for a
screwdriver makes it easier to undo the screw afterwards.
♦ If the pull-off screws still cannot be undone, warm the, up with
a hot air blower.

Undoing pull-off screws with a hot air blower

– Set the temperature adjustment potentiometer -2- to maximum

heating performance and set the air flow two stage switch
-3- to position 3.

Caution

Risk of burns from hot air blower.

♦ Only warm up the pull-off screws with a hot air blower.
♦ By warming the pull-off screws, the cover plate and parts
in its vicinity are heated up strongly too. Where necessary,
protect these parts by a piece of sheet covering.

7. Engine control unit 337

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Heat the shear bolt head -1- for approximately 20 to 30 sec‐

onds.
Continued for slackened screws

– Release shear bolt -1- using the screwdriver -2-.

– Remove protective housing -1-.

WARNING

If the engine control unit touches the plus pole of the battery,
this will destroy the engine control unit.

– Unlock catch in -direction of the arrow- and remove the engine

control unit -1-.
– Unlock plug connections for engine control unit - J623- and
pull off.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Install unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Install in the reverse order of removal. When doing this, note the
following:
– It is imperative for the protective housing to be put back in
place on the engine control unit - J623- .
– Clean the threaded holes for the shear bolts to remove safety
agent residues. Cleaning can be done using a tapper.
– Secure the protective housing with new shear bolts.
After installing a new engine control unit, the following work step
must be performed:
– Activate engine control unit ⇒ Vehicle diagnostic tester.

338 Rep. gr.23 - Mixture preparation - injection

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

8 Engine noise speaker

8.1 Removing and installing engine noise

speaker
Removing
– Removing plenum chamber cover and then bulkhead plenum
chamber ⇒ Body Work; Rep. gr. 50 .
– Disconnect the plug connections -arrows-.
– Unscrew nut -2- (7 Nm) and the control element of the engine
noise speaker -3-.
– Unscrew nuts -1- (3 Nm) and the control element of the engine
noise speaker -4-.
Install
Installation is carried out in the reverse order.

8. Engine noise speaker 339

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

26 – Exhaust system
1 Removing and installing exhaust
pipes/silencers

1.1 Summary of components - front, middle

and rear silencer, vehicles with front-
wheel drive
For vehicles with engine identification characters CLHA, CLHB,
CRKB

1 - Seal
❑ replace after removal
❑ Check fitting position
⇒ page 341
2 - Warm-type clamp, 7 Nm
❑ replace
❑ Fitting position
⇒ page 341
3 - Pre-exhaust pipe
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
❑ Observe part number ⇒
ETKA - Electronic Cata‐
logue of Original Parts
4 - Support
❑ replace if damaged
5 - 23 Nm
6 - Exhaust flap control unit -
J883-
❑ removing and installing
⇒ page 350
7 - Front clamping sleeve, 30
Nm
❑ before tightening, align
exhaust system free of
stress ⇒ page 355
❑ Fitting position
⇒ page 341
❑ Tighten screwed con‐
nections uniformly
8 - Retaining strap
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
❑ replace if damaged unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
9 - Hanger
❑ replace if damaged

340 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

10 - 20 Nm
11 - Rear tunnel bridge
12 - Front tunnel bridge
13 - Middle and rear silencer
❑ for first equipment a building unit, replace individually when carrying out repairs ⇒ page 355
❑ Align exhaust system free of stress ⇒ page 355
❑ removing and installing ⇒ page 351
14 - Separation point
❑ for repairs
❑ marked with recesses around the circumference
❑ Separation point ⇒ page 355

Installation position of gasket between exhaust gas cleaning mod‐

ule and pre-exhaust pipe
• The square catch of the gasket -arrow- must be in the groove
of the exhaust gas cleaning module.

Installation position of clamping sleeve for pre-exhaust pipe

• Angle -α- = 0 ± 30°.

Installation position of front clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 20°.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
• Bolted connection to the
unless authorised by right.
ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• Nuts upwards

1. Removing and installing exhaust pipes/silencers 341

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of rear clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 30°.
• Bolted connection to the left.
• Nut downwards

1.2 Summary of components - front, middle

and rear silencer, vehicles with front-
wheel drive
For vehicles with engine identification characters CKFB, CKFC

1 - Seal
❑ replace after removal
❑ Check fitting position
⇒ page 343
2 - Warm-type clamp, 7 Nm
❑ replace
❑ Fitting position
⇒ page 343
3 - Pre-exhaust pipe
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
4 - Support
❑ replace if damaged
5 - 23 Nm
6 - Exhaust flap control unit -
J883-
❑ removing and installing
⇒ page 350
7 - Front clamping sleeve, 30
Nm
❑ before tightening, align
exhaust system free of
stress ⇒ page 355
❑ Fitting position
⇒ page 343
❑ Tighten screwed con‐
nections uniformly
8 - Retaining strap
❑ replace if damaged
9 - Hanger Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ replace if damaged with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

342 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of gasket between exhaust gas cleaning mod‐

ule and pre-exhaust pipe
• The square catch of the gasket -arrow- must be in the groove
of the exhaust gas cleaning module.

Installation position of clamping sleeve for pre-exhaust pipe

• Angle -α- = 0 ± 30°.

Installation position of front clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 20°.
• Bolted connection to the right.
• Nuts upwards.

1. Removing and installing exhaust pipes/silencers 343

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of rear clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 30°.
• Bolted connection to the left.
• Nut downwards

1.3 Summary of components - front, middle

and rear silencer, vehicles with front-
wheel drive
For vehicles with engine identification characters CUPA

1 - Gasket
❑ replace after removal
❑ Check fitting position
⇒ page 345
2 - Warm-type clamp, 7 Nm
❑ replace
❑ Fitting position
⇒ page 345
3 - Support
❑ replace if damaged
4 - 23 Nm
5 - Exhaust flap control unit -
J883-
❑ removing and installing
⇒ page 350
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
6 - Pre-exhaust pipe unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
7 - Front clamping sleeve, 30
Nm
❑ before tightening, align
exhaust system free of
stress ⇒ page 355
❑ Fitting position
⇒ page 345
❑ Tighten screwed con‐
nections uniformly
8 - Retaining strap
❑ replace if damaged
9 - Middle and rear silencer
❑ for first equipment a building unit, replace individually when carrying out repairs ⇒ page 355
❑ Align exhaust system free of stress ⇒ page 355

344 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013
❑ removing and installing ⇒ page 351
10 - Hanger
❑ replace if damaged
11 - 20 Nm
12 - Rear tunnel bridge
13 - Front tunnel bridge
14 - Separation point
❑ for repairs
❑ marked with recesses around the circumference
❑ Separation point ⇒ page 355

Installation position of gasket between exhaust gas cleaning mod‐

ule and pre-exhaust pipe
• The square catch of the gasket -arrow- must be in the groove
of the exhaust gas cleaning module.

Installation position of clamping sleeve for pre-exhaust pipe

• Angle -α- = 0 ± 30°.

Installation position of front clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 20°.
• Bolted connection to the right.
• Nuts upwards.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1.4 Front, middle and rear silencer, vehicles

with EU4 emission level
For vehicles with engine identification characters CRVC

1. Removing and installing exhaust pipes/silencers 345

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Gasket
❑ replace after removal
❑ Check fitting position
⇒ page 347
2 - Warm-type clamp, 7 Nm
❑ replace
❑ Fitting position
⇒ page 347
3 - Pre-exhaust pipe
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
4 - 23 Nm
5 - Support
❑ replace if damaged
6 - Front clamping sleeve, 30
Nm
❑ before tightening, align
exhaust system free of
stress ⇒ page 355
❑ Fitting position
⇒ page 347
❑ Tighten screwed con‐
nections uniformly
7 - Front tunnel bridge
8 - 20 Nm
9 - Retaining strap
❑ replace if damaged
10 - Hanger
❑ replace if damaged
11 - Rear tunnel bridge
12 - Separation point
❑ for repairs
❑ marked with recesses around the circumference
❑ Separation point ⇒ page 355
13 - Middle and rear silencer
❑ for first equipment a building unit, replace individually when carrying out repairs ⇒ page 355
❑ Align exhaust system free of stress ⇒ page 355
❑ removing and installing ⇒ page 351

346 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of gasket between exhaust gas cleaning mod‐

ule and pre-exhaust pipe
• The square catch of the gasket -arrow- must be in the groove
of the exhaust gas cleaning module.

Installation position of clamping sleeve for pre-exhaust pipe

• Angle -α- = 0 ± 30°.

Installation position of front clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 20°.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
• Bolted connection to the right.
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• Nuts upwards.

Installation position of rear clamp

– Install clamping sleeve in the angle position shown.
• Angle -α- = approximately 30°.
• Bolted connection to the left.
• Nut downwards

1.5 Summary of components - front, middle

and rear silencer, vehicles with four-
wheel drive
For vehicles with engine identification characters CLHA, CKFC

1. Removing and installing exhaust pipes/silencers 347

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1 - Gasket
❑ replace after removal
❑ Check fitting position
⇒ page 349
2 - Warm-type clamp, 7 Nm
❑ replace
❑ Fitting position
⇒ page 349
3 - Support
❑ replace if damaged
4 - Exhaust flap control unit -
J883-
❑ removing and installing
⇒ page 350
5 - 23 Nm
6 - Pre-exhaust pipe
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
7 - Front clamping sleeve, 30
Nm
❑ before tightening, align
exhaust system free of
stress ⇒ page 355
❑ Fitting position
⇒ page 349
❑ Tighten screwed con‐
nections uniformly
8 - Middle and rear silencer
❑ Align exhaust system
free of stress ⇒ page 355
❑ removing and installing ⇒ page 351
9 - Retaining strap
❑ replace if damaged
10 - Hanger
❑ replace if damaged
11 - 20 Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
12 - Rear tunnelunless
bridge
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

348 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Installation position of gasket between exhaust gas cleaning mod‐

ule and pre-exhaust pipe
• The square catch of the gasket -arrow- must be in the groove
of the exhaust gas cleaning module.

Installation position of clamping sleeve for pre-exhaust pipe

• Angle -α- = 0 ± 30°.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Installation position of front
with respect to theclamp
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Install clamping sleeve in the angle position shown.

• Angle -α- = approximately 50°.
• Bolted connection to the right.
• Nuts upwards.

1.6 Removing and installing exhaust pipe

Removing
– Remove tunnel cover at bottom ⇒ Body Work; Rep. gr. 50 .
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA
– Separate electrical plug connection -1-.
Continued for all vehicles
– Slacken the clamping sleeve -2- and slide it backwards.

1. Removing and installing exhaust pipes/silencers 349

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -1-.

– Slacken screw -2- and remove air filter housing.
– Remove pre-exhaust pipe.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

Replace gasket.

– check fitting position:

• ⇒ Fig. ““Installation position of clamping sleeve for pre-exhaust
pipe”“ , page 341
• ⇒ Fig. ““Installation position of gasket between exhaust gas
cleaning module and pre-exhaust pipe”“ , page 341
– Align exhaust system free of stress ⇒ page 355 .
Tightening torques
♦ Vehicles with front-wheel drive (for 1.6 ltr engines)
⇒ “1.1 Summary of components - front, middle and rear si‐
lencer, vehicles with front-wheel drive”, page 340
♦ Vehicles with front-wheel drive (for 2.0 ltr engines)
⇒ “1.2 Summary of components - front, middle and rear si‐
lencer, vehicles with front-wheel drive”, page 342
♦ Vehicles with four-wheel drive
⇒ “1.5 Summary of components - front, middle and rear si‐
lencer, vehicles with four-wheel drive”, page 347
♦ Vehicles with EU4 emission level
⇒ “1.4 Front, middle and rear silencer, vehicles with EU4 emis‐
sion level”, page 345

1.7 Removing and installing the exhaust

flap control unit - J883-
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Removing with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Remove tunnel cover at bottom ⇒ Body Work; Rep. gr. 50 .

– Separate electrical plug connection -1-.
– Release screws -arrows-, remove exhaust flap control unit -
J883- .
Install
Installation is carried out in the reverse order. When installing,
note the following:
♦ Specified torque: 9 Nm.

350 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.8 Removing and installing rear silencer,

vehicles with front-wheel drive
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CRVC
Removing
– Vehicles without separation point Replace middle or rear si‐
lencer ⇒ page 355 .
– Vehicles with separation point: Loosen clamping sleeve
-arrow- and press forwards.
– Release screws -arrows-, remove rear silencer.

Vehicles with 1.6l engine

Vehicles with 2.0l engine

Continued for all vehicles
If the exhaust pipe must be removed:
– Remove the rear left underfloor trim panel ⇒ Body Work; Rep.
gr. 50 .

1. Removing and installing exhaust pipes/silencers 351

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove rear tunnel bridge -2- ⇒ page 340 .

– Loosen the clamping sleeve -2- and slide it forwards.

Note

-Do not pay attention to the position 1-.

– Unscrew screws -arrows-, remove middle silencer.

Install
Installation isProtected
carried out in the reverse order. When installing,
note the following:
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

Note

Replace gasket.

– check fitting position:

• Installation position of clamping sleeve for pre-exhaust pipe
⇒ Fig. ““Installation position of clamping sleeve for pre-exhaust
pipe”“ , page 341
• Installation position of gasket between exhaust gas cleaning
module and pre-exhaust pipe
⇒ Fig. ““Installation position of gasket between exhaust gas
cleaning module and pre-exhaust pipe”“ , page 341
• Installation position of front clamp
⇒ Fig. ““Installation position of front clamp”“ , page 341
• Installation position of rear clamp
⇒ Fig. ““Installation position of rear clamp”“ , page 342
– Align exhaust system free of stress ⇒ page 355 .
Tightening torques
♦ For 1.6l engine
⇒ “1.1 Summary of components - front, middle and rear si‐
lencer, vehicles with front-wheel drive”, page 340
♦ For 2.0l engine
⇒ “1.2 Summary of components - front, middle and rear si‐
lencer, vehicles with front-wheel drive”, page 342

352 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.9 Removing and installing rear silencer,

vehicles with front-wheel drive
For vehicles with engine identification characters CUPA
Removing
– Vehicles without separation point Replace middle or rear si‐
lencer ⇒ page 355 .
– Vehicles with separation point: Unhook suspension -3- from
the rear silencer.

– Loosen clamping sleeve -arrow- and press forwards.

– Screw out screw -4- and remove rear silencer.

If the exhaust pipe must be removed:
– Remove the rear left underfloor trim panel ⇒ Body Work; Rep.
gr. 50 .

– Remove rear tunnel bridge -2- ⇒ page 344 .

– Loosen the clamping sleeve -2- and slide it forwards.

Note

-Do not pay attention to the position 1-.

– Unscrew screw -2-, remove middle silencer -1-.

Install
Install in the reverse order of removal. When doing this, note the
following:
– Align exhaust system free of stress ⇒ page 355 .
Tightening torques
♦ Summary of components - front, middle and rear silencer, ve‐
hicles with front-wheel drive ⇒ page 344

1.10 Removing and installing rear silencer,

vehicles with four-wheel drive
For vehicles with engine identification characters CLHA, CKFC
Removing
– Loosen clamping sleeve -arrow- and press forwards.

– Unhook suspension -3- frombythe

Protected rearCopying
copyright. silencer.
for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Remove screws -2 andwith
4-,respect
remove rear silencer -1-.
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

354 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.11 Replacing middle or rear silencer

Special tools and workshop equipment required
♦ Body saw e.g. -V.A.G 1523 A-
♦ Protective goggles

Note

♦ For vehicles with torsion beam axle, a disconnection is provi‐

ded in the exhaust pipe to facilitate removal of the exhaust
system.
♦ The separation point is marked by indentation on the circum‐
ference of the exhaust pipe.

Procedure

WARNING

To avoid injury from metal shavings, wear eye protection and

protective clothing.

– Separate exhaust pipe at right angles at the separation point

-arrow 2-.
– When installing, position warm-type clamp -4- at the side
markings -arrow 1- and -arrow 3-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– check
unless fitting
authorised position:
by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
• ⇒ Fig. ““Installation position of rear clamp”“ , page 342
– Align exhaust system free of stress ⇒ page 355 .
– Tighten bolted connections of warm-type clamp evenly to 30
Nm.
• The bolted connection points to the left.

1.12 Aligning exhaust system free of stress

• The exhaust system is aligned when cold.
– Slacken bolted connections of clamping sleeve -2-.

1. Removing and installing exhaust pipes/silencers 355

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Push the rear silencer so far forward until the pre-tensioning

on the retaining strap on the exhaust pipe is -a- = 5 mm.

– Install clamping sleeve in the angle position shown.

• Vehicles with front-wheel-drive: Angle -α- = approximately 20°.
• Vehicles with four-wheel drive: Angle -α- = approximately 50°.
• Bolted connection to the right.
• Nuts upwards.
– Tighten bolted connections of clamping sleeve evenly to 30
Nm.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

1.13 Align exhaust tailpipes

– Align rear silencer in such a way that there is an equal distance
-a- and -b- between bumper opening and exhaust tailpipes.
– For centering the exhaust tailpipes, if necessary loosen the
suspension of the rear silencer.

1.14 Inspecting the exhaust system for leak‐

tightness
– Start engine and run at idling speed.
– Close off exhaust tailpipes for the duration of the leak test, for
example using cloths or plugs.
– Check connection points for leaktightness by listening: ex‐
haust manifold at cylinder head, exhaust gas turbocharger at
pre-exhaust pipe, etc.
– Eliminate any leak found.

356 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

2 Cleansing exhaust emissions

2.1 Summary of components - exhaust gas

cleaning
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA

1 - Pre-exhaust pipe
❑ removing and installing
⇒ page 349
❑ Align exhaust system
free of stress
⇒ page 355
2 - Open warm-type clamp
❑ replace after removal
❑ Fitting position
⇒ page 341
❑ Tightening torque
-Pos. 2- ⇒ page 340
3 - Gasket
❑ Check fitting position
⇒ page 341
4 - Screw
❑ Tightening torque and
tightening order
⇒ page 366
5 - Gasket
6 - Open warm-type clamp
❑ Fitting position
⇒ page 376
❑ Tightening torque and
tightening order
⇒ page 376
7 - Radiator for exhaust gas re‐
circulation
❑ removing and installing
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
⇒ page
unless 381
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
8 - Screw
❑ Tightening torque and
tightening order ⇒ page 375
9 - Screw
❑ Tightening torque and tightening order ⇒ page 375
10 - Bracket
❑ for radiator for exhaust gas recirculation
11 - Open warm-type clamp
❑ Fitting position ⇒ page 358
12 - Bolt
❑ Tightening torque and tightening order ⇒ page 265

2. Cleansing exhaust emissions 357

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

13 - Exhaust gas turbocharger

❑ removing and installing ⇒ page 267
14 - Seal
❑ put it onto the catalyst
15 - Bracket
❑ for exhaust gas cleaning module
❑ with balancing element
❑ Prepare balancing element for installation ⇒ page 365
16 - Bolt
Tightening torque and tightening order ⇒ page 265

17 - Screw
❑ Tightening torque and tightening order ⇒ page 366
18 - 9 Nm
19 - Measurement pipe
❑ to differential pressure sender - G505-
❑ Union nut tightening torque 45 Nm
20 - Bolt
❑ Tightening torque and tightening order ⇒ page 366
21 - Screw
❑ Tightening torque and tightening order ⇒ page 359
22 - Bracket
❑ for exhaust gas cleaning module
❑ with balancing elements
❑ Prepare balancing elements for installation ⇒ page 365
23 - Screw
❑ Tightening torque and tightening order ⇒ page 359
24 - Exhaust gas cleaning module
❑ Particle filter with catalyser
❑ removing and installing ⇒ page 360
25 - Screw Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Tightening torque and tightening order
with respect to ⇒ page
the correctness 366
of information in this document. Copyright by ŠKODA AUTO A. S.�

Installation position of gripper clamp for exhaust gas cleaning

module
• Angle -α- = 30°.

358 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Bracket -2- for exhaust gas cleaning module - tightening torques

and tightening order
– Tighten screws in steps in the specified sequence:
Stage Screws Tightening torque
1. -3- by hand as far as the stop
2. -1- 20 Nm
3. -3- 20 Nm

2.2 Summary of components - exhaust gas

cleaning
For vehicles with engine identification characters CRVC

1 - Screw
❑ Tightening torque and
tightening order
⇒ page 369
2 - Support
❑ must not be fitted
❑ screwed onto the cylin‐
der head
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
❑ Tightening
with respect torque
to the correctness and in this document. Copyright by ŠKODA AUTO A. S.�
of information

tightening order
⇒ page 369
3 - Catalytic converter/diesel
particulate filter
❑ Country-specific com‐
ponents
❑ removing and installing
⇒ page 368
4 - Screw
❑ Tightening torque and
tightening order
⇒ page 369
5 - Gasket
❑ replace after removal
6 - Clamping sleeve
❑ Tightening torque and
tightening order
⇒ page 369
7 - Gasket
❑ replace after removal
8 - Clamping sleeve, 7 Nm
9 - Pre-exhaust pipe
❑ removing and installing ⇒ page 349
❑ Align exhaust system free of stress ⇒ page 355
10 - Screw
❑ Tightening torque and tightening order ⇒ page 369

2. Cleansing exhaust emissions 359

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

11 - Nuts
❑ Tightening torque and tightening order ⇒ page 369
12 - Support
❑ screwed onto the crankcase
❑ Tightening torque and tightening order ⇒ page 369

2.3 Removing and installing exhaust gas

cleaning module
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA

Note

The exhaust gas cleaning module is attached to the engine with

4 balancing elements among other items. These balancing ele‐
ments have a left-hand thread on the outside. When being
screwed on, the screw -1- by
Protected initially
copyright.moves the
Copying for balancing
private or commercialelement
purposes, in part or in whole, is not permitted
-2-as a result of the friction on thebypegs
unless authorised ŠKODA-3-.AUTOTheA. S.balancing
ŠKODA AUTOelement
A. S. does not guarantee or accept any liability
moves across the screw head against the left-hand thread, de‐
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

spite the fact that the screw is rotating in the anticlockwise direc‐
tion, thus compensating for the clearance between the compo‐
nents. The balancing element must be freely rotatable via its left-
hand thread, otherwise the pegs do not create friction on the
screw that is needed to move the balancing element. In order not
to minimise the friction, no lubricant should get onto the peg.

Function of the balancing element

Special tools and workshop equipment required

♦ Socket insert SW 8 - 3247-
♦ Assembly aid - T10511-
♦ Calibration tool - T10512-
Removing
– Remove assembly carrier with steering gear ⇒ Chassis; Rep.
gr. 40 .
– Remove pre-exhaust pipe ⇒ page 349 .
– Drain coolant ⇒ page 139 .

360 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Remove rear coolant pipe ⇒ page 164 .

– Remove radiator for exhaust gas recirculation ⇒ page 381 .
For engines with identification characters CLHA, CLHB, CKFB,
CKFC, CUPA
– Remove exhaust temperature sender -1- and -2-
⇒ page 372 .

– Remove lambda probe - G39- ⇒ page 370 .

– Open heat protection sleeve -1-.

– Release screw -arrow-.

– Open clamp -A-, pull out hose, unclip pipeline -B- and remove
with the differential pressure sender - G505- .
For engines with identification characters CRKB

2. Cleansing exhaust emissions 361

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect electrical plug connections and lay the electric ca‐

bles to one side:
1- for exhaust gas temperature sender 4 - G648-
2- for exhaust gas temperature sender 3 - G495-
3- for exhaust gas temperature sender 2 - G448-
– Remove exhaust temperature sender - G648- , -G495- and -
G448- ⇒ page 370 .

– Remove lambda probe - G39- ⇒ page 370 .

– Remove lambda probe - G130- ⇒ page 323 .

– Open heat protection sleeve -1-.

– Take electrical plug connection-5 - out of the holder, discon‐
nect and expose electric cable.
– Disconnect electrical plug connections -3 and 4- expose elec‐
tric wiring loom.
– Release screw -2-.

– Detach vacuum hose -arrow- and put to one side.

362 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screw -3-.

– Loosen hose clamps -1-, remove hoses.
– Press out pipeline -2- and remove the differential pressure
sender.
Continued for all vehicles

– Open hose clamp -1-, remove coolant hose.

– Unscrew screws -2- and -3- and swivel coolant line to the side.
Vehicles fitted with auxiliary heating

– Raise holding clamps -1- and undo hose clamp -3-, remove
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
coolant hoses. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Release nuts -arrows-, remove coolant pipe.
Vehicles with four-wheel drive
– Unscrew the right driveshaft from the angle gearbox ⇒ Sus‐
pension; Rep. gr. 40 and tie up towards the rear.

– Release screws -arrows- and remove heat shield -1-.

– To reinstall, mark the position of the flexible disk and the angle
gearbox flange to each other.
– Unscrew the propshaft from the angle gearbox -arrows-, while
counterholding with a lever on the triangular flange.

2. Cleansing exhaust emissions 363

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Push engine/gearbox assembly slightly forward (towards the

front of the body) and then pull off the propshaft from the angle
gearbox.

WARNING

Risk of damage to the gasket ring -arrow- in the flange of the

propshaft.
Push propshaft horizontally as far back and towards the left
vehicle side as possible.

Note

In case of damaged gasket ring the propshaft must be replaced.

– Tie up propshaft towards the left vehicle side.

Continued for all vehicles

– Release screw -arrow-.

Note

The feet of the assembly aid - T10511- are supported on the

screw heads of the cylinder head cover.

– Place assembly aid - T10511- as shown, suspend retaining

bracket -arrow- in the suspension catch of the exhaust gas
cleaning module.

364 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open clamp -1- and position it on the flared opening of the

exhaust gas cleaning module.
– Unscrew the remaining screws in the order -4 … 2-.
Right-hand drive
– Push engine forwards with the assistance of a second me‐
chanic.
Continued for all vehicles
– Swivel the exhaust gas cleaning module downwards away
from the engine and push it upwards.
– Pull retaining bracket out of the suspension catch of the ex‐
haust gas cleaning module and remove the exhaust gas clean‐
ing module downwards.
Install
• Mounting aid - T10511- positioned on engine

Note

♦ Ensure that the retaining bracket of the assembly aid -

T10511- pivoted in the front wall direction is - »open«-.
♦ Replace seals, self-locking nuts and gripper clamp for exhaust
gas cleaning module.
♦ Fit all cable straps back at the same points when re-installing.

Caution

Risk of stress fractures and engine damage caused by the

built-in exhaust gas cleaning module being under tension.
♦ Before installation, ensure that these balancing elements
are not stiff or tight.
♦ The balancing element must turn freely in the thread.
♦ Lubricant must only be applied to the thread, the retaining
lugs must remain »clean«.
♦ The screw retaining lugs must be bent far enough for the
balancing element to be moved when the screw is
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
screwed in. with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Check for and ensure ease of movement of the balancing el‐

ements -arrow-.
– Fully unscrew balancing elements in the clockwise direction
(left-hand thread).
– Clean stiff threads and moisten them with lubricant if neces‐
sary.

Caution

Retaining lugs of the balancing elements must not be mois‐

tened with lubricants of any kind. Reducing the friction would
impair the function of the balancing element.

2. Cleansing exhaust emissions 365

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Bring retaining lugs to the functional dimension using the cal‐

ibration tool - T10512- .
– Slide the balancing element onto the firing pin, insert into the
centring sleeve and turn the retaining lugs back by striking the
ball stud lightly using the palm of your hand.
– Screw balancing elements in fully by hand and unscrew again
by 45°.

– Disconnect the gasket -1- at the exhaust gas cleaning module.

– Unhook clamp screw and lay clamp -2- entirety on the flared
opening of the exhaust gas cleaning module. Do not bend
clamp
Right-hand drive
– Push engine forwards with the assistance of a second me‐
chanic. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
Continued for all vehicles
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

– Guide exhaust cleaning module to the installation position

from below, push it up and hook the bracket in the suspension
catch of the exhaust gas cleaning module.
The exhaust gas cleaning module is now suspended in weight-
neutral manner in the approximate installation position.

Note

Replace all fixing screws of the exhaust gas cleaning module.

Tightening order for exhaust gas cleaning module

Stage Bolt Measure
1. Warm-type Position using the sealing flange and
clamp -1- tighten to 3 Nm
2. Screw -2- Tighten until hand-tight and immedi‐
ately loosen by a torquing angle of 90°
3. Warm-type tighten to 8 Nm
clamp -1-
4. Screw -2- tighten to 20 Nm
5. Screw -3- insert and lock by pressing. Do not
tighten or turn screw
6. Screws -4- insert and lock by pressing. Tighten
screws to 20 Nm
7. Screw -3- tighten to 20 Nm

366 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew balancing element (left-hand thread) -1- on the cyl‐

inder head using socket insert SW 8 - 3247- in
-arrow direction- as far as the stop, then rotate a further 90°.

Continued tightening order

Stage Bolt Measure
8. Screw -5- insert and lock by pressing
9. Screw -5- tighten to 20 Nm
10. Screw -5- Turn 90° further
11. Screw -5- turn 45° further
Assembling is performed continuing in the reverse order, while
paying attention to the following:
Vehicles with four-wheel drive
– Unscrew propshaft from angle gearbox ⇒ Gearbox; Rep. gr.
39 .
– Screw on the right driveshaft to the angle gearbox ⇒ Suspen‐
sion; Rep. gr. 40 .
Continued for all vehicles
– Install radiator for exhaust gas recirculation ⇒ page 381 .
– Electrical connections and proper routing ⇒ Electrical System;
Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
– Install the left coolant pipe ⇒ page 163 .
– Install the rear coolant pipe ⇒ page 164 .
– Install pre-exhaust pipe ⇒ page 349 .

– Connect coolant hose, fit hose clamp -1-.

– Screw in screws -2- and -3- and tighten to 10 Nm.

2. Cleansing exhaust emissions 367

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Connect hoses, fit hose clamps -1-.

– Tighten screw -3-, -Position 3- ⇒ page 40 .
– Screw on holder for differential pressure sender to cylinder
head cover, -Position 5- ⇒ page 80 .
– Install the assembly carrier ⇒ Chassis; Rep. gr. 40 .
– After replacing the exhaust gas cleaning module, reset the
learning values⇒ Vehicle diagnostic tester, Targeted Func-
tions , Resetting learning values .

2.4 Removing and installing catalytic con‐

verter
For vehicles with engine identification characters CRVC
Removing
– Remove the sound dampening systems and tunnel cover ⇒
Body Work; Rep. gr. 50 .
– Undo the screws of the clamping sleeve -2-, leave the clamp‐
ing sleeve in the fitting position.
– Open clamp -1- and remove.
– Unscrew the screws -3-, slide the clamping sleeve -2- to the
rear and remove the pre-exhaust pipe -A-.

– Unscrew the fixing nuts -1-, undo the screws -2- by a quarter
turn.
– Remove engine cover ⇒ page 9 .

368 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Unscrew the screws -arrows- of the coolant line , pull the cool‐
ant line slightly to the front.
– Unscrew screws -1- and -3-, open and remove the clamp -2-.
– Carefully remove the catalytic converter upwards.
Install

Note

♦ Replace self-locking nuts and screws as well as gasket rings,

gaskets and O-rings after disassembly.
♦ Secure all hose connection ends with spring-type clips that
comply with the series design ⇒ ETKA - Electronic Catalogue
of Original Parts .
♦ Fit all cable straps on again in the same place when installing.

– Position the new seal onto the centering studs of the flared
opening onto the catalytic converter, slide the new clamp over
the flared opening.
– Place the catalytic converter into position from the top and,
using the pin bolts, insert into the bottom mounting bracket.
– For further tightening sequence, see the following table
⇒ page 369

Tightening torques and tightening sequence, catalytic converter

Stage Screw Measure
I Warm-type Position via the sealing flange, secure
clamp -1- screw
II Screws Tighten until hand-tight and immedi‐
-2 and 3- ately loosen by a torquing angle of 90°
III Warm-type tighten to 8 Nm
clamp -1-
IV Nuts -4- tighten to 20 Nm
V Screws -5- tighten to 20 Nm
VI Screw -2- tighten to 20 Nm, turn a further 90°,
then turn another 45°
VII Screw -3- tighten to 20 Nm
Further installation occurs in reverse order.

2. Cleansing exhaust emissions 369

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

3 Exhaust temperature regulation

3.1 Summary of components - exhaust tem‐

perature regulation

Caution

Malfunction caused by loose exhaust gas temperature sender

♦ The threads of the exhaust gas temperature sender -
G495- and -G648- are coated. They must NOT be coated
additionally with hot bolt paste and must be tightened to
the specified tightening torque.

1 - Lambda probe downstream

4 - Exhaust gas temperature

sender 2 - G448- , 60 Nm
❑ only for vehicles with en‐
gine identification characters CRKB
❑ removing and installing ⇒ page 373
5 - 8 Nm
6 - Differential pressure sender - G505-
❑ removing and installing ⇒ page 319

370 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

7 - Support
8 - Exhaust gas pressure sensor 1 - G450-
❑ only for vehicles with engine identification characters CRKB
❑ removing and installing ⇒ page 320
9 - 8 Nm
10 - Exhaust gas temperature sender 3 - G495-
❑ removing and installing ⇒ page 372
❑ the thread of the exhaust gas temperature sender is coated and must not be coated additionally with hot
bolt paste
❑ 2.0l engines: 60 Nm
❑ 1.6l engines: 45 Nm
11 - Lambda probe - G39- with heating for lambda probe - Z19- , 55 Nm
❑ removing and installing ⇒ page 323
12 - Exhaust gas cleaner

3.2 Removing and installing the exhaust

gas temperature sender 1 - G235-
Special tools and workshop equipment required
♦ Flexible-head wrench SW 17 , e.g. -V.A.G 1331/10-
Removing

Note

♦ Fit all cable straps on again in the same place when installing.
♦ When removing, the electric cable must be not cut off, since
doing so would mean that fault diagnosis would no longer be
possible. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Remove engine cover at the topwith
⇒ respect
page to9the
. correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Open heat protection sleeve.
– Take electrical plug connection-1 - out of the holder, discon‐
nect and expose electric wiring loom.
– Unscrew exhaust gas temperature sender 1 - G235-
-Position 2- using extension SW 17 - V.A.G 1331/10- .
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Protect exhaust gas temperature sender from impacts and

shocks: Do not use any exhaust gas temperature sender that
has been dropped.
♦ Coat threads with hot bolt paste; hot bolt paste ⇒ ETKA -
Electronic Catalogue of Original Parts .

3. Exhaust temperature regulation 371

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Fitting position of the exhaust gas temperature sender -G235- :

• Angled shank -1- downwards horizontally.
– Electrical connections and proper routing ⇒ Electrical System;
Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
Tightening torques
♦ Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370

3.3 Remove and install exhaust gas tem‐

perature sender 3 - G495- / exhaust gas
temperature sender 4 - G648-
Special tools and workshop equipment required
♦ Set of tools - T10395-
Removing

Note

– Remove engine cover at the top ⇒ page 9 .

– Expose the following plug connections and electric cables:
2 - for exhaust gas temperature sender 4 - G648-
3 - for exhaust gas temperature sender 3 - G495-

372 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Screw exhaust gas temperature sender concerned out using

a tool from the tool kit - T10395- and a suitable insertion tool.
1- for exhaust gas temperature sender 4 - G648-
2- for exhaust gas temperature sender 3 - G495-
Install
Installation is carried out in the reverse order. When installing,
note the following:

Caution

Malfunction caused by loose exhaust gas temperature sender

♦ The threads of the exhaust gas temperature sender -
G495- and -G648- are coated. They must NOT be coated
additionally with hot bolt paste and must be tightened to
the specified tightening torque.

Note

Protect exhaust gas temperature sender from impacts and

shocks: Do not use any exhaust gas temperature sender that has
been dropped.

– Electrical connections and proper routing ⇒ Electrical System;

Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations.
Tightening torques
♦ Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370

3.4 Removing and installing the exhaust

gas temperature sender 2 - G448-
For vehicles with engine identification characters CRKB
Special tools and workshop equipment required
♦ Set of tools - T10395 A-
Removing

Note

– Remove engine cover ⇒ page 9 . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

3. Exhaust temperature regulation 373

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Disconnect plug connection -3- and lay the electric cable to

one side.

– Unscrew exhaust temperature sender 2 - G448- -arrow-.

Install
Installation is performed in a similar way in the reverse order. Pay
attention to the following points:

Caution

Malfunction caused by a loose exhaust gas temperature send‐

er.
♦ the thread of the temperature sender 2 - G448- is coated.
It must NOT be coated additionally with hot bolt paste and
must be tightened to the specified tightening torque.

Note

Protect exhaust gas temperature sender from impacts and

shocks: Do not use any exhaust gas temperature sender that has
been dropped.

Fitting position of the exhaust gas temperature sender 2 - G448- :

• The angled shaft -1- must point vertically upwards.

– Electrical connections and proper routing ⇒ Electrical System;
Rep. gr. 97 and ⇒ Current flow diagrams, Electrical fault find‐
ing and Fitting locations. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Tightening torques
♦ Summary of components - exhaust temperature regulation
⇒ “3.1 Summary of components - exhaust temperature regu‐
lation”, page 370

374 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4 Exhaust gas recirculation system

4.1 Exhaust gas recirculation with radiator

for exhaust gas recirculation - Summary
of components
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA

1 - Radiator for exhaust gas re‐

circulation
❑ removing and installing
⇒ page 381
2 - Screw
❑ Tightening torque and
tightening order
⇒ page 376 , if only the
radiator for exhaust gas
recirculation has been
removed
3 - Support
❑ for radiator for exhaust
gas recirculation
4 - Screw
❑ Tightening torque and
tightening order
⇒ page 376 , if only the
radiator for exhaust gas
recirculation has been
removed
5 - Open warm-type clamp
❑ replace after removal
❑ Fitting position
⇒ page 376
❑ Tightening torque and
tightening order
⇒ page 376
6 - Seal
❑ replace after removal
7 - Exhaust gas cleaning mod‐
ule
❑ removing and installing
⇒ page 360
8 - Control motor 2 for exhaust gas recirculation - V339-
❑ removing and installing ⇒ page 379

4. Exhaust gas recirculation system 375

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Note

Control motor for exhaust gas recir‐

culation is protected against dam‐
age using heat from a heat-protec‐
tion matting. If this heat-protection
matting gets damaged it will need to
be replaced and the control motor
checked by heat damage (it may al‐
so need to be replaced).

9 - 9 Nm
10 - Seal
❑ replace after removal

Installation position of air guide hose at radiator for exhaust gas

recirculation

Installation position for radiator for exhaust gas recirculation

• Angle -α- = 10 … 15°.

Radiator for exhaust gas recirculation - tightening torques and

tightening order
– Tighten screws in steps in the given sequence:
Stage Screws Tightening torque
1. Warm-type 7 Nm
clamp -3-
2. -1, 2- by hand as far as the stop
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
3. -1, 2-authorised20by Nm
unless ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

376 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.2 Exhaust gas recirculation with radiator

for exhaust gas recirculation - Summary
of components
For vehicles with engine identification characters CRVC

1 - Gasket
❑ replace after removal
2 - Connecting pipe
❑ to exhaust manifold
3 - 20 Nm
❑ replace after removal
4 - 8 Nm
❑ replace after removal
5 - 20 Nm
❑ replace after removal
6 - Temperature for exhaust
gas recirculation - G98-
❑ remove with wrench
from tool set - T10395 A-
7 - Double screw, 20 Nm
❑ replace after removal
8 - Vacuum line
9 - 8 Nm
10 - Vacuum line
11 - Changeover valve
Protected for ra‐Copying for private or commercial purposes, in part or in whole, is not permitted
by copyright.
diator of exhaust gas recircu‐
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
lation - N345-
12 - Connecting pipe
❑ to cylinder head
13 - 20 Nm
❑ replace after removal
14 - Screw
❑ observe the order of
tightening up ⇒ page 378
15 - Support
❑ for radiator for exhaust gas recirculation
❑ screwed onto the cylinder head
❑ observe the order of tightening up ⇒ page 378
16 - 20 Nm
17 - Radiator for exhaust gas recirculation
❑ removing and installing ⇒ page 383

4. Exhaust gas recirculation system 377

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

Tightening torques and -sequence holder for radiator for exhaust

gas recirculation
Stage Bolts Tightening torque
1. -2 ... 5- by hand as far as the stop
2. -1- tighten to 20 Nm
3. -2 ... 5- tighten to 55 Nm

4.3 Control motor for exhaust gas recircula‐

tion - V338- - Summary of components
For vehicles with engine identification characters CRKB, CRVC

1 - Coolant hose
2 - Spring strap clamp
3 - EGR control motor - V338-
❑ with EGR potentiometer
- G212-
❑ removing and installing
⇒ page 379
4 - Gasket
❑ replace after removal
5 - Gasket
❑ replace after removal
6 - 9 Nm

378 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.4 Removing and installing control motor

for exhaust gas recirculation - V338-
For vehicles with engine identification characters CRVC, CRKB
Special tools and workshop equipment required
♦ Hose clamps up to ∅ 25 mm - MP7-602 (3094)-
Removing

Note

Observe rules for cleanliness.

– Remove throttle valve module - J338- ⇒ page 327 .

– Separate electrical plug connection -3-.
– Disconnect the coolant hose with the hose clamp -MP7-602
(3094)- .
– Loosen hose clamp -2-, remove coolant hose.
– Unscrew screws -arrows-, remove control motor for exhaust
gas recirculation - V338- .
Install
Install in the reverse order of removal. When doing this, note the
following:

Note

♦ Replace gasket.
♦ Secure all hose connection ends with spring-type clips that
comply with the series design ⇒ ETKA - Electronic Catalogue
of Original Parts .

Tightening torques
♦ Control motor for exhaust gas recirculation - V338- - Summary
of components
⇒ “4.3 Control motor for exhaust gas recirculation V338 -
Summary of components”, page 378
♦ Intake manifold - Summary of components
⇒ “6.1 Assembly overview - intake manifold”, page 325 .

4.5 Removing and installing control motor 2

for exhaust gas recirculation - V339-
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6362-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Removing unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Remove engine cover at the top ⇒ page 9 .

4. Exhaust gas recirculation system 379

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– if a vacuum hose is present: Remove it -arrow- and lay to the

side.

– Press release buttons on the hose -1- for crankcase ventila‐

tion, remove hose from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Loosen spring strap clip -3-, remove air guide pipe from air
mass meter - G70- .
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

– Loosen spring strap clips -1, 2-, remove exhaust gas recircu‐
lation hose.
– Press heat protection sleeve to the side, disconnect electrical
plug connection -3-.
– Unscrew screws -arrows-, remove control motor 2 for exhaust
gas recirculation - V339- .
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Replace gasket and O-ring after disassembly.

♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

Tightening torques
♦ Summary of components - exhaust gas recirculation with ra‐
diator for exhaust gas recirculation
⇒ “4.1 Exhaust gas recirculation with radiator for exhaust gas
recirculation - Summary of components”, page 375
♦ Summary of components - exhaust gas turbocharger with
component parts
⇒ “1.1 Exhaust gas turbocharger with component parts - Sum‐
mary of components”, page 265
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

380 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

4.6 Removing and installing radiator for ex‐

haust gas recirculation
For vehicles with engine identification characters CLHA, CLHB,
CRKB, CKFB, CKFC, CUPA
Special tools and workshop equipment required
♦ Hose clip pliers - VAS 6340-
Removing
– Remove battery tray ⇒ Electrical System; Rep. gr. 27 .
– Remove left coolant pipe ⇒ page 163 .
– if a vacuum hose is present: Remove it -arrow- and lay to the
side.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Press release buttons on the hose -1- for crankcase ventila‐
tion, remove hose from cylinder head cover.
– Disconnect vacuum hoses on the air guide pipe -arrows-.
– Release screw -2-, swivel air guide pipe with inlet connection
towards the rear and detach from exhaust gas turbocharger.

Note

-Do not pay attention to the position 3-.

– Unscrew screws -arrows-, remove pulsation dampener -1-.

Vehicles fitted with a manual gearbox:
– Remove switching and selector linkage from gearbox, un‐
screw linkage support and lay aside with the linkages ⇒
Gearbox; Rep. gr. 34 .
Vehicles with dual clutch gearbox 0CW:
– Remove selector lever linkage from gearbox, unscrew linkage
support and strap up with linkages ⇒ Gearbox; Rep. gr. 34 .
Vehicles with dual clutch gearbox 0D9:
– Remove selector lever linkage from gearbox and pull it out of
the linkage support ⇒ Gearbox; Rep. gr. 34 .
Vehicles with four-wheel drive
– Remove pre-exhaust pipe ⇒ page 349 .
Continued for all vehicles

4. Exhaust gas recirculation system 381

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Press heat protection sleeve to the side, disconnect electrical

plug connection -5-.
– Loosen hose clamp -3-, remove air guide hose.
– Loosen hose clamp -4-, remove coolant hose.
– Loosen screw -6-, remove particle filter clamp.
– Unscrew screw -1-, loosen screw -2-.
– Remove radiator for exhaust gas recirculation.
Install
Installation is carried out in the reverse order. When installing,
note the following:

Note

♦ Check seal for damage, renew if necessary.

♦ If heat protection seal is defective, check control motor 2 for
exhaust gas recirculation - V339- for heat damage, replace if
necessary.
♦ Replace gaskets, clamp and spring strap clips after disassem‐
bly.
♦ Secure all hose connections with spring-type clips that comply
with the series design ⇒ ETKA - Electronic Catalogue of Orig‐
inal Parts .

– Mount hose -2- on radiator -1- for exhaust gas recirculation.

• Fitting position: Marking “EGR side” -arrow- points to the ex‐
haust gas recirculation radiator.
– Ensure that the air guide hose fitting is free of tension.

– Position radiator -1- for exhaust gas recirculation on the ex‐

haust gas cleaning module with gasket and gripper clamp.
– Turn radiator for exhaust gas recirculation in anticlockwise di‐
rection -arrow- and simultaneously put hose -3- onto the ex‐
haust gas turbocharger-2-.

382 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Bring gripper clamp -3- to installation position ⇒ page 376 .

– Tighten screw connections ⇒ page 376 .
– Install the left coolant pipe ⇒ page 163 .
Tightening torques
♦ Radiator for exhaust gas recirculation - tightening torques and
tightening order
⇒ Fig. ““Radiator for exhaust gas recirculation - tightening tor‐
ques and tightening order”“ , page 376
♦ Summary of components - front, middle and rear silencer, ve‐
hicles with four-wheel drive ⇒ page 347

4.7 Removing and installing radiator for ex‐

haust gas recirculation
For vehicles with engine identification characters CRVC
Special tools and workshop equipment required
♦ Socket insert - T10347-
♦ Socket insert XZN 10 - T10501-
♦ Set of tools - T10395 A-
Removing
– Remove catalytic converter ⇒ page 368 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– respect
Drainto coolant ⇒ page 139 in. this document. Copyright by ŠKODA AUTO A. S.�
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with the correctness of information

– Loosen hose clamp -1- and disconnect hose. Unscrew the

nuts -arrows-.
– Tie up coolant pipe, e.g. using cable ties.

– Unscrew screws -1- with the Polydrive socket - T10347- , un‐

screw nuts -2-.
– Remove connection pipe -A-.

4. Exhaust gas recirculation system 383

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Open the clamps -arrows-, remove the coolant hoses, un‐

screw the temperature sender for exhaust gas recirculation -
G98- -1- using a suitable socket from the tool set - T10395 A- .

– Unscrew the screws -1- with the Polydrive socket XZN 10 -

T10501- , unscrew mounting bracket for vacuum line -2-.
– Detach vacuum line from radiator for exhaust gas recircula‐
tion.

– Unscrew screws -arrows- and carefully remove the radiator for

exhaust gas recirculation -A- through the vehicle tunnel.
Install
Install in the reverse order of removal. When doing this, note the
following:

Note

♦ Replace self-locking nuts and screws as well as gasket rings,

– Install high catalytic converter ⇒ page 368 .

– Top up coolant ⇒ page 140 .
Tightening torques
♦ Summary of components - exhaust gas recirculation with ra‐
diator for exhaust gas recirculation
⇒ “4.2 Exhaust gas recirculation with radiator for exhaust gas
recirculation - Summary of components”, page 377

384 Rep. gr.26 - Exhaust system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

28 – Glow plug system

1 Glow Plug System

1.1 Summary of components - preheating system

1 - Hall sender - G40-

❑ removing and installing
⇒ page 388
2 - 9 Nm
3 - O-ring
❑ no spare parts, in case
of damage replace to‐
gether with Hall sender -
G40-
4 - Glow plug
♦ Glow plug 1 - Q10-
♦ Glow plug 2 - Q11-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Glow plug 3 - Q12- unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�

♦ Glow plug 4 - Q13-

❑ the combustion cham‐
ber pressure sender for
cylinder 3 - G679- is only
integrated for cylinder 3
in the glow plug for en‐
gine identification char‐
acters CRKB
❑ Glow plug variants
⇒ page 386
❑ Glow plugs without
combustion chamber
pressure sender 17 Nm
❑ Glow plugs with com‐
bustion chamber pres‐
sure sender 12 Nm
❑ removing and installing
⇒ page 386
5 - Electrical plug connection
❑ for glow plugs
6 - Sealing flange on the gearbox side
❑ removing and installing ⇒ page 63
7 - Rotor
❑ for engine speed sender - G28-
❑ removing and installing ⇒ page 63
8 - Engine speed sender - G28-
❑ removing and installing ⇒ page 389
9 - 4.5 Nm

1. Glow Plug System 385

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

1.2 Removing and installing glow plugs

Note

Metal glow plugs are installed in this engine.

Special tools and workshop equipment required

♦ Flexible-head wrench SW 10 -3220-
♦ Pliers - 3314-
♦ Cleaning and degreasing agent , e.g. -D 009 401 04-
♦ Protective goggles and gloves
♦ Polydrive socket 12 mm - VAS 6454- , only for engine identi‐
fication characters CRKB
Removing
Glow plug variants
1- Glow plugs with combustion chamber pressure sender - on‐
ly for cylinder 3 with engine identification characters CRKB
2- Glow plugs without combustion chamber pressure sender
Observe all safety measures and notes for assembly work on the
fuel system and on the injection system as well as the rules for
cleanliness ⇒ page 3 .
– Switch off ignition and pull out ignition key.
– Remove engine cover at the top ⇒ page 9 .

Caution

Risk of damaging support sleeves.

♦ Only press pliers - 3314- for disconnecting glow plug con‐
nectors so far together that they grip the support sleeve
collar securely without damaging it.

– Open holding clamps of the electrical wiring loom and discon‐

nect the electrical plug connections from the glow plugs as
follows.

386 with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Rep. gr.28 - Glow plug system
Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Position pliers - 3314- using the sliding groove -arrow A- at the

support sleeve collar -arrow B-, as shown in the illustration.

Caution

♦ Carefully remove the glow plug connectors from the glow

plugs.
♦ If the plug is damaged when disconnecting it, the complete
wiring loom including the plugs must be replaced (plugs
cannot be replaced separately).

– Carefully disconnect the plug from the glow plugs.

– Clean glow plugs in the cylinder head (no dirt must fall into the
cylinder).
When cleaning, for example:

WARNING

Wear protective gloves and protective googles when working

with grease remover!

1. Suction off heavy dirt using a vacuum cleaner.

2. Spray the pencil type glow plug channel using a brake
cleaner or a suitable cleaner, let it take effect for a short
period of time and blow out with compressed air.
3. Then clean the pencil type glow plug channel with a cloth
which is wetted with oil.

– To release the glow plugs, use socket wrench SW 10 - 3220- .

Note

With engine identification characters CRKB, use Polydrive socket

12 mm - VAS 6454- to remove the glow plug in cylinder 3.

Install
Installation is carried out in reverse order.
– To tighten the glow plugs, use socket wrench SW 10 - 3220- .

Note

With engine identification characters CRKB, use Polydrive socket

12 mm - VAS 6454- to tighten the glow plug in cylinder 3.

1. Glow Plug System 387

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Place the glow plug connectors -1- back onto the glow plugs
-arrows-.

Note

Make sure the glow plug connectors fit tightly.

Tightening torques
♦ Summary of components - preheating system ⇒ page 385

1.3 Removing and installing automatic glow

period control unit - J179-
Removing
– Unlock catches -arrows-, remove cover.

– Remove automatic glow period control unit - J179- -arrow-

from the socket in the e-box engine compartment.
Install
Installation is carried out in the reverse order.

1.4 Removing and installing Hall sender -

G40-
Removing
– Remove engine cover at the top ⇒ page 9 .

388 Rep. gr.28 - Glow plug system

Octavia III 2013 ➤ , Octavia III 2014 ➤
1.6/66; 77; 81; 2.0/105; 110; 135 kW TDI CR engine - Edition 10.2013

– Release screws -arrows-, push the right charge air pipe slight‐
ly to the side.
– Separate electrical plug connection -2-.
– Unscrew screw -1-, pull off Hall sender - G40- .
Install
Installation is carried out in the reverse order.
♦ Tightening torque
⇒ “1.1 Summary of components - preheating system ”,
page 385

1.5 Removing and installing engine speed

sender - G28-
Special tools and workshop equipment required
♦ Assembly tool - T10118-
♦ Socket insert size 4 - T10370-
Removing
– Remove the sound dampening system ⇒ Body Work; Rep.
gr. 50 .
– Disconnect electrical plug connection -1- using the assembly
tool - T10118- .

Note

To unlock the electrical

Protectedplug connection
by copyright. without
Copying for private orthe assembly
commercial tool
purposes, in part or in whole, is not permitted
- T10118- , use a unless
screwdriver to press plug on the engine speed
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
sender and simultaneously raise release button with a thin wire
hooklet.

– Unscrew screw -2-, remove engine speed sender - G28- .

Install
Installation is carried out in the reverse order. When installing,
note the following:
Tightening torque
♦ Summary of components - preheating system ⇒ page 385

1. Glow Plug System 389

Tdi CR Engine 1 6 and 2 0 Repair Manual Eng
100% (1)
Tdi CR Engine 1 6 and 2 0 Repair Manual Eng
713 pages
Manual Service Motor TSI 63-77 KW D3E802BE98F-1 - 2 - 63 - KW - 77 - KW - TSI - Engine
50% (2)
Manual Service Motor TSI 63-77 KW D3E802BE98F-1 - 2 - 63 - KW - 77 - KW - TSI - Engine
173 pages
SM 20
No ratings yet
SM 20
351 pages
Engine Daca Dada Dacb Dpba Dpbe Dpca Dfya Repair Manual Eng
No ratings yet
Engine Daca Dada Dacb Dpba Dpbe Dpca Dfya Repair Manual Eng
550 pages
Audi A6 2005-2011 - 6-Cyl. TDI Engine (2.7l. 3.0l. 4-Valve Common Rail, EU5), Mechanics - PDFs Free Online
No ratings yet
Audi A6 2005-2011 - 6-Cyl. TDI Engine (2.7l. 3.0l. 4-Valve Common Rail, EU5), Mechanics - PDFs Free Online
386 pages
Isuzu 4fb1 Engine Manual
36% (11)
Isuzu 4fb1 Engine Manual
3 pages
5-Service Manual 6-Cylinder Engine ASN & BBJ Mechanics
No ratings yet
5-Service Manual 6-Cylinder Engine ASN & BBJ Mechanics
243 pages
1 2 55 KW TDI CR Engine PDF
No ratings yet
1 2 55 KW TDI CR Engine PDF
266 pages
Sistema Electrico Toureg
No ratings yet
Sistema Electrico Toureg
538 pages
TDI Injection and Glow Plug System 6-Cyl 3 0 LTR 4-Valve Common Rail Generation II
100% (2)
TDI Injection and Glow Plug System 6-Cyl 3 0 LTR 4-Valve Common Rail Generation II
87 pages
Clha CLHB CKFB CKFC CRVC Cupa CRKB CRMB Cuna Tdi CR Engine Eng
100% (2)
Clha CLHB CKFB CKFC CRVC Cupa CRKB CRMB Cuna Tdi CR Engine Eng
432 pages
Q5 2015+ A005FY20020-Basic Equipment (L0L) From September 2016
No ratings yet
Q5 2015+ A005FY20020-Basic Equipment (L0L) From September 2016
1,612 pages
Seat 4 Cylinder Diesel Engine 16l and 20l 4v Tdi Common Rail Ea288 Workshop Manual
100% (1)
Seat 4 Cylinder Diesel Engine 16l and 20l 4v Tdi Common Rail Ea288 Workshop Manual
456 pages
VW Touareg 2 Body Repairs Exterior Eng
No ratings yet
VW Touareg 2 Body Repairs Exterior Eng
410 pages
Skoda Scala 2019+ - 1.6l70 85 KW TDI CR Engine (DGTA, DGTD)
No ratings yet
Skoda Scala 2019+ - 1.6l70 85 KW TDI CR Engine (DGTA, DGTD)
415 pages
Workshop Manual Transporter 2016 1-29
No ratings yet
Workshop Manual Transporter 2016 1-29
167 pages
MC 10073951 2280
No ratings yet
MC 10073951 2280
228 pages
Engine Mechanical Cnta Cxba Cnsa CXBB CNSB Cxca CXCB Eng
100% (1)
Engine Mechanical Cnta Cxba Cnsa CXBB CNSB Cxca CXCB Eng
372 pages
VW Tiguan 2 Fuel System Diesel Eng
No ratings yet
VW Tiguan 2 Fuel System Diesel Eng
126 pages
Skyactiv-X An Innovative Gasoline Engine With Compression Ignition
100% (3)
Skyactiv-X An Innovative Gasoline Engine With Compression Ignition
37 pages
1 4 51kW TDI 1 4 59kW TDI Engine
No ratings yet
1 4 51kW TDI 1 4 59kW TDI Engine
162 pages
Engine Cuaa Repair Manual Eng
100% (1)
Engine Cuaa Repair Manual Eng
631 pages
Diesel Engine 1 6 and 2 0 Tdi Common Rail Ea288 - Eng PDF
No ratings yet
Diesel Engine 1 6 and 2 0 Tdi Common Rail Ea288 - Eng PDF
456 pages
SSP00054220-Nr 542 The Passat 2015
No ratings yet
SSP00054220-Nr 542 The Passat 2015
60 pages
Engine Dcya Ddma Dfga DFGB CRFC Cykb Dfha Dcyb DGDB Dbga Crga DFGC Cykc DBGC CRGB CRFZ CRFD Dgte Dffa DGTC DGTD Repair Manual Eng
No ratings yet
Engine Dcya Ddma Dfga DFGB CRFC Cykb Dfha Dcyb DGDB Dbga Crga DFGC Cykc DBGC CRGB CRFZ CRFD Dgte Dffa DGTC DGTD Repair Manual Eng
745 pages
VW Golf Gti 2005
No ratings yet
VW Golf Gti 2005
8 pages
FABIA - Accessories Brochure - January 2019 PDF
No ratings yet
FABIA - Accessories Brochure - January 2019 PDF
64 pages
Electrical System
100% (1)
Electrical System
404 pages
Maintenance-Oil Change T6F
No ratings yet
Maintenance-Oil Change T6F
5 pages
Cfpa 4cyl Injection Engine Eng Amarok VW
No ratings yet
Cfpa 4cyl Injection Engine Eng Amarok VW
259 pages
The Sharan 2011 Electrics/Electronics Design and Function: Service Training
100% (1)
The Sharan 2011 Electrics/Electronics Design and Function: Service Training
40 pages
Workshop Manual Transporter 2016 17-29
No ratings yet
Workshop Manual Transporter 2016 17-29
288 pages
4-Cylinder Direct Injection Engine (1 8 2 0 LTR 4-Valve - Generation II)
No ratings yet
4-Cylinder Direct Injection Engine (1 8 2 0 LTR 4-Valve - Generation II)
397 pages
Service: Passat 2015 Passat Variant 2015
No ratings yet
Service: Passat 2015 Passat Variant 2015
69 pages
Workshop Manual Transporter 2016 19-29
No ratings yet
Workshop Manual Transporter 2016 19-29
157 pages
Maintenance PDF
No ratings yet
Maintenance PDF
155 pages
1 9 77 KW Tdi PD Engine
100% (1)
1 9 77 KW Tdi PD Engine
397 pages
Tiguan 2020navigation - Navigation Circuit (W - Amplifier & Central Speaker) (Navigation System) - ALLDATA Repair
No ratings yet
Tiguan 2020navigation - Navigation Circuit (W - Amplifier & Central Speaker) (Navigation System) - ALLDATA Repair
4 pages
BMW ETM + Documentation Files List
No ratings yet
BMW ETM + Documentation Files List
17 pages
SSP 510 Active Cylinder Management ACT in The 1.4l 103 KW TSI Engine
No ratings yet
SSP 510 Active Cylinder Management ACT in The 1.4l 103 KW TSI Engine
36 pages
D4B805AB6B6-Technical Data For Petrol Engines
No ratings yet
D4B805AB6B6-Technical Data For Petrol Engines
6 pages
938 G
100% (1)
938 G
24 pages
SSP 337 20l Fsi Engine With Turbocharger
No ratings yet
SSP 337 20l Fsi Engine With Turbocharger
28 pages
SSP 104 Skoda Fabia III Vehicle Introduction Part II
No ratings yet
SSP 104 Skoda Fabia III Vehicle Introduction Part II
64 pages
Service: FABIA 2000
No ratings yet
Service: FABIA 2000
52 pages
VW Repair - Noise Detection and Diagnosis Guide
No ratings yet
VW Repair - Noise Detection and Diagnosis Guide
29 pages
Body Work
No ratings yet
Body Work
201 pages
Service: León 2013 León ST 2013
No ratings yet
Service: León 2013 León ST 2013
268 pages
Engine Ajh Awc Mechanics Eng PDF
No ratings yet
Engine Ajh Awc Mechanics Eng PDF
290 pages
25-Service Manual Fuel Supply System Diesel Engines ASB, ASE, BNG, BVN & BMC
No ratings yet
25-Service Manual Fuel Supply System Diesel Engines ASB, ASE, BNG, BVN & BMC
83 pages
Golf 2010 2.0L
No ratings yet
Golf 2010 2.0L
162 pages
SM 9 PDF
No ratings yet
SM 9 PDF
218 pages
Technical Specifications New Volvo V60
No ratings yet
Technical Specifications New Volvo V60
3 pages
1,6 75 KW Engine
No ratings yet
1,6 75 KW Engine
144 pages
BRC PDF
No ratings yet
BRC PDF
106 pages
SSP 840233 Ea288 Diesel Engine Family
No ratings yet
SSP 840233 Ea288 Diesel Engine Family
4 pages
SM 7
No ratings yet
SM 7
237 pages
Users Manual: Mitsubishi Delica Spacegear: DR D John Pons
No ratings yet
Users Manual: Mitsubishi Delica Spacegear: DR D John Pons
49 pages
SSP-288 Audi A8 03' Distributed Funktion PDF
No ratings yet
SSP-288 Audi A8 03' Distributed Funktion PDF
32 pages
Service: Wheel and Tire Guide
No ratings yet
Service: Wheel and Tire Guide
113 pages
Wheel Loader Specifications: Service Weight 13.7 T - 14,5 T Engine Output 130 KW Loading Buckets 2.3 - 6.0 M
No ratings yet
Wheel Loader Specifications: Service Weight 13.7 T - 14,5 T Engine Output 130 KW Loading Buckets 2.3 - 6.0 M
10 pages
CX-5 - General Information
No ratings yet
CX-5 - General Information
71 pages
Audi A6 2.8L 2011 (C7) 7th Generation Brochure
0% (1)
Audi A6 2.8L 2011 (C7) 7th Generation Brochure
80 pages
Mercedes Transmission Overview
100% (1)
Mercedes Transmission Overview
12 pages
Skid Steer Loader Hydraulic System - Caterpillar
No ratings yet
Skid Steer Loader Hydraulic System - Caterpillar
2 pages
SSP 265 Vehicle Electrics in Polo MY 02
100% (1)
SSP 265 Vehicle Electrics in Polo MY 02
24 pages
New Car Pre-Delivery Inspection Checklist - The Automotive India - Com PDF
No ratings yet
New Car Pre-Delivery Inspection Checklist - The Automotive India - Com PDF
6 pages
BMW E39 TIS Blower Motor Replacement
100% (2)
BMW E39 TIS Blower Motor Replacement
24 pages
Sponsorship Proposal: Email ID
No ratings yet
Sponsorship Proposal: Email ID
14 pages
Jib Crane Inspection Report 04-1003736 - J1604751 - NQ5643 - PDF
No ratings yet
Jib Crane Inspection Report 04-1003736 - J1604751 - NQ5643 - PDF
3 pages
Drive Belt Replacement: Removal Procedure
No ratings yet
Drive Belt Replacement: Removal Procedure
55 pages
C10 Builder's Guide - Summer 2025 USA
No ratings yet
C10 Builder's Guide - Summer 2025 USA
116 pages
Steering Column
No ratings yet
Steering Column
61 pages
MB Pricelist April 2021
No ratings yet
MB Pricelist April 2021
4 pages
Data Sheet WP4D108E200
No ratings yet
Data Sheet WP4D108E200
5 pages
Parts - 3121275 - 02-01-18 - Global - English - Manual de PArtes de 1930 - 3246 2011 PDF
No ratings yet
Parts - 3121275 - 02-01-18 - Global - English - Manual de PArtes de 1930 - 3246 2011 PDF
222 pages
Engine Volvo Penta Tad1641ve
No ratings yet
Engine Volvo Penta Tad1641ve
2 pages
Brochure p5770c p5870c p6870c t3 en 30 20035803 e
No ratings yet
Brochure p5770c p5870c p6870c t3 en 30 20035803 e
24 pages
Wiring Diagrams
No ratings yet
Wiring Diagrams
11 pages
2013 Hyundai Sonata 2.4L ABS 2
No ratings yet
2013 Hyundai Sonata 2.4L ABS 2
1 page
Cranes - Rough Terrain Crane Specifications - RT300-1 Series
No ratings yet
Cranes - Rough Terrain Crane Specifications - RT300-1 Series
4 pages
Cat Forklift p4000 p5000 p5000 p6500 p7000 Schematic Service Operation Maintenance Manual
No ratings yet
Cat Forklift p4000 p5000 p5000 p6500 p7000 Schematic Service Operation Maintenance Manual
28 pages
00000935 (1)
No ratings yet
00000935 (1)
5 pages
Note!: Shock Absorber For Honda Forza 350-MY2020
No ratings yet
Note!: Shock Absorber For Honda Forza 350-MY2020
8 pages
Inventario Seminuevos 20 Marzo
No ratings yet
Inventario Seminuevos 20 Marzo
41 pages
The Comparison of Octane 90 Mixed Fuel With Bioaditive Towards The Performance of The Otto Engine
No ratings yet
The Comparison of Octane 90 Mixed Fuel With Bioaditive Towards The Performance of The Otto Engine
4 pages
Xemodex Cem Removal 99 04
No ratings yet
Xemodex Cem Removal 99 04
1 page
Toyota Innova Overdrive Advertorial
No ratings yet
Toyota Innova Overdrive Advertorial
6 pages
Pneus Militares
No ratings yet
Pneus Militares
7 pages
Epson Epl n3000 Part List
No ratings yet
Epson Epl n3000 Part List
22 pages