Pectel C2 ECU

Introduction

The Pectel C2 ECU is designed for use in pre-2007 Subaru Impreza WRX Group N rally
cars. The ECU is a direct replacement for the factory fitted ECU and is supplied complete
with engine maps. It is also supplied with configuration software.

The Pectel C2 ECU has an onboard Engine Logbook facility. Data from this is downloaded
using the ECU Offload Tool software.

Installation

The ECU is a direct replacement for the factory fitted ECU. Unplug the factory supplied
ECU and plug in the Pectel C2 ECU.

Product Information 29E-071594-1E 1

Dimensions
Comms connector

167.00 (6.57”)
176.00 (6.92”)
172.00 (6.77”)

157.00 (6.18”)

(1.25”)
32.00
Block E Block C Block A
Pins 92 to 122 Pins 51 to 67 Pins 1 to 22
Block D Block B
Pins 68 to 91 Pins 23 to 50

Dimensions in millimetres and (inches)

Specifications

Description Value Description Value

Voltage Range 6V to 18V Communication RS232
Injector Drives 4 High Impedance Internal Sensors Barometric Pressure
Ignition Drives 2 Internal Clamp ECU Temperature
PWM / Relay Outputs 3 Battery voltage
Crank Sensor Type Inductive Temperature Range –40°C to 85°C
Cam Sensor Type Inductive Weight 325 grams
Analogue Inputs 6
Application Software DESCPRO,
Ordering information
ECU Offload Tool and
Pi Toolbox
Data logging 40 Channels Product Part number
Data Throughput 100Hz Pectel C2 ECU 01E-500229
RAM 128kB or 512kB
Flash 128kB
A/D Accuracy 10bit

2 Product Information 29E-071594-1E

Connector information

Comms connector

Connector Mating connector

Lemo EEA-1B-307-CLV Lemo PFA-1B-307

Comms connector pinout details

Pin Function Pin Function

1 Ground 5 RX232
2 12V 6 TX232
3 CAN High 7 Ground
4 CAN Low

Main connector pinout

The main connector is divided into five sections, Blocks A to E. The location of pins on the connector blocks are
shown in the connector diagram before each pinout table.

Main Connector Block A

A1 A2 A3 A4 A5 A6 A7
A8 A9 A10 A11 A12 A13 A14 A15
A16 A17 A18 A19 A20 A21 A22
Face view of Block A, 22 way

Pin Signal name Description

A1 SPD 5 Road speed
A2 RLAL 14 ALS light (AC) / main relay
A3 AN 9 (ALSSW) ALS switch (defog)
A4 SPD 6 Turbo speed
A5 VIGIN 1 Ignition power +ve
A6 MAIN 1 Main relay
A7 PWR GND Power ground
A8 SW 1 (NTLSW) Neutral switch
A9 SW 2 (FANSW) Fan switch
A10 DIG GND Digital ground
A11 No connection -
A12 No connection -
A13 RLAL 9 Fuel pump Sig / AC relay
A14 VIGIN 2 Ignition power +ve
A15 PWR GND Power ground
A16 No connection -
A17 No connection -
A18 SW 1 (HBKSW) Handbrake switch
A19 SW 2 (FBKSW) Foot brake switch
A20 RS232 RX RS232 RX
A21 RS232 TX RS232 TX
A22 PWR GND Power ground

Product Information 29E-071594-1E 3

Main Connector Block B

B1 B2 B3 B4 B5 B6 B7 B8 B9
B10 B11 B12 B13 B14 B15 B16 B17 B18 B19
B20 B21 B22 B23 B24 B25 B26 B27 B28
Face view of Block B, 28 way

Pin Signal name Description

B1 CAM Cam sensor +ve
B2 CRANK Crank sensor +ve
B3 AN 8 Diff select
B4 KNOCK 1 Knock 1
B5 No connection -
B6 VDIF +5VE Diff control
B7 AN 3 (TPS) Throttle sensor
B8 AN 1 (MAP) Manifold pressure
B9 5V SENSOR OUT 5V sensor power
B10 ANA GND Analogue ground
B11 ANA GND Analogue ground
B12 AN 13 ISC sw / RH TGV sensor
B13 No connection -
B14 No connection -
B15 ANA 7 (EXT LAM) External Lambda
B16 No connection -
B17 REGO Rear A/F sensor +ve
B18 AN 4 (ECT) Water temperature
B19 No connection -
B20 No connection -
B21 PWR GND Power ground
B22 PWR GND Power ground
B23 AN 13 ISC sw / RH TGV sensor
B24 No connection -
B25 AN 11 Launch select
B26 PWR GND Power ground
B27 AN 5 (AAT) Ambient air temp
B28 AN 10 ALS Switch

4 Product Information 29E-071594-1E

Main Connector Block C
C1 C2 C3 C4 C5 C6
C7 C8 C9 C10 C11 C12
C13 C14 C15 C16 C17
Face view of Block C, 17 way

Pin Signal name Description

C1 PWR GND Power ground
C2 RVCAM (DIG) RH AVCS sensor +ve
C3 ANA GND Analogue ground
C4 MOT OUT 2A RH TGV valve open
C5 MOT OUT 2B RH TGV valve close
C6 VBAT OUT RH AVCS +12ve
C7 No connection -
C8 PWR GND Power ground
C9 LVCAM (DIG) LH AVCS sensor +ve
C10 MOT OUT 1A LH TGV open
C11 MOT OUT 1B LH TGV close
C12 RLAH6 RH AVCS valve
C13 AN 2 (MAF) Airflow sensor
C14 PWR GND Power ground
C15 ANA GND Analogue ground
C16 RLAH 5 LH AVCS valve
C17 VBAT OUT LH AVCS +12ve

Product Information 29E-071594-1E 5

Main Connector Block D

D1 D2 D3 D4 D5 D6 D7
D8 D9 D10 D11 D12 D13 D14 D15 D16
D17 D18 D19 D20 D21 D22 D23 D24
Face view of Block D, 24 way

Pin Signal name Description

D1 ANA GND Analogue ground
D2 No connection -
D3 No connection -
D4 INJ 4 Fuel injector 4
D5 INJ 3 Fuel injector 3
D6 INJ 2 Fuel injector 2
D7 No connection -
D8 PWR GND Power ground
D9 TACHO Tacho output
D10 RLAH 3 Idle valve
D11 SPD 1 FL speed
D12 SPD 2 FR speed
D13 RHTR (RLAH4) Rear A/F heater
D14 SPEEDO Speedo output
D15 RLAH 2 Fuel pump PWM no Imob
D16 RLAH 2 Fuel pump PWM Imob
D17 PWR GND Power ground
D18 PWR GND Power ground
D19 SPD 3 RL speed
D20 SPD 4 RR speed
D21 IGN 4 Ignition coil 4
D22 IGN 3 Ignition coil 3
D23 IGN 2 Ignition coil 2
D24 IGN 1 Ignition coil 1

Product Information 29E-071594-1E 6

Main Connector Block E

E1 E2 E3 E4 E5 E6 E7 E8 E9
E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E21
E22 E23 E24 E25 E26 E27 E28 E29 E30 E31
Face view of Block E, 31 way

Pin Signal name Description

E1 INJ 1 Fuel injector 1
E2 VBAT IN Switched power
E3 VBAT IN Switched power
E4 FHTR (RLAH4) Front A/F heater
E5 FHTR (RLAH4) Front A/F heater
E6 No connection -
E7 No connection -
E8 PWR GND Power ground
E9 PWR GND Power ground
E10 PERM +VE Permanent power +ve
E11 RLAL 13 Water spray (ISC)
E12 No connection -
E13 No connection -
E14 AN 12 (ACT) Air charge temperature
E15 RLAL 11 Check light
E16 RLAL 10 Purge valve
E17 RLAL 8 Rad Fan 1
E18 PWR GND Power ground
E19 FEGO Front A/F sensor +ve
E20 No connection -
E21 No connection -
E22 No connection -
E23 No connection -
E24 RLAH 1 Boost control valve
E25 No connection -
E26 RLAL 12 Shift light
E27 RLAL 9 Fuel pump Sig / AC relay
E28 RLAL 7 Rad fan 2
E29 ANA GND Analogue ground
E30 Knock 2 Knock sensor 2
E31 No connection -

Product Information 29E-071594-1E 7