Public Authority for Civil Aviation

FLIGHT INSPECTION MANUAL

For
Radio Navigation Aids

Manual No: 1.3.20.

Issue Date: 09 Apr 2020
Revision Number: Initial

Copyright © 2020 by the Public Authority of Civil Aviation (PACA), Oman

All rights reserved. No part of this publication may be stored in a retrieval system, transmitted, or reproduced in
any way, including but not limited to photo-copy, magnetic or other record, without the prior agreement and
written permission of the CEO, for PACA, Oman
 Flight Inspection Manual for Radio Navigation Aids Initial

DOCUMENT CONTROL SHEET

TITLE

FLIGHT INSPECTION MANUAL FOR RADIO NAVIGATION AIDS

CLASSIFICATION TYPE OF DOCUMENT STATUS
Technical
Public Draft
Document

Internal Presentation Under Revision

Exclusive use by Proposal /

Upgradeable
PACA Report

Confidential Other Final

NAME / RESP SIGNATURE

Musleh Abdullah Al Jahdhami

DRAFTED BY :
Vilina Eka Lestari

Khaled Eltanany

REVIEWED BY: Sulaiman Al-Zadjali: Director ANSD

Mubarak Saleh Al Ghelani : DG

APPROVED BY:
DGCAR

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 2

 Flight Inspection Manual for Radio Navigation Aids Initial

List of Effective Pages

Date Date Date
Page Rev Page Rev Page Rev
of of of
No. No. No. No. No. No.
Issue Issue Issue
1 Initial 9-4-20 41 Initial 9-4-20 81
2 Initial 9-4-20 42 Initial 9-4-20 82
3 Initial 9-4-20 43 Initial 9-4-20 83
4 Initial 9-4-20 44 Initial 9-4-20 84
5 Initial 9-4-20 45 Initial 9-4-20 85
6 Initial 9-4-20 46 Initial 9-4-20 86
7 Initial 9-4-20 47 Initial 9-4-20 87
8 Initial 9-4-20 48 Initial 9-4-20 88
9 Initial 9-4-20 49 Initial 9-4-20 89
10 Initial 9-4-20 50 Initial 9-4-20 90
11 Initial 9-4-20 51 Initial 9-4-20 91
12 Initial 9-4-20 52 Initial 9-4-20 92
13 Initial 9-4-20 53 Initial 9-4-20 93
14 Initial 9-4-20 54 Initial 9-4-20 94
15 Initial 9-4-20 55 Initial 9-4-20 95
16 Initial 9-4-20 56 Initial 9-4-20 96
17 Initial 9-4-20 57 Initial 9-4-20 97
18 Initial 9-4-20 58 Initial 9-4-20 98
19 Initial 9-4-20 59 Initial 9-4-20 99
20 Initial 9-4-20 60 Initial 9-4-20 100
21 Initial 9-4-20 61 Initial 9-4-20 101
22 Initial 9-4-20 62 Initial 9-4-20 102
23 Initial 9-4-20 63 Initial 9-4-20 103
24 Initial 9-4-20 64 Initial 9-4-20 104
25 Initial 9-4-20 65 Initial 9-4-20 105
26 Initial 9-4-20 66 Initial 9-4-20 106
27 Initial 9-4-20 67 107
28 Initial 9-4-20 68 108
29 Initial 9-4-20 69 109
30 Initial 9-4-20 70 110
31 Initial 9-4-20 71 111
32 Initial 9-4-20 72 112
33 Initial 9-4-20 73 113
34 Initial 9-4-20 74 114
35 Initial 9-4-20 75 115
39 Initial 9-4-20 79 119
40 Initial 9-4-20 80 120

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 3

 Flight Inspection Manual for Radio Navigation Aids Initial

Intentionally Left Blank

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 4

 Flight Inspection Manual for Radio Navigation Aids Initial

Glossary of Terms or Abbreviations

The following terms or acronyms may be used in any manual or document published by
PACA. Reproduction in part or whole is allowed without prior approval. The Document
Control Office reserves the rights to include such a listing in any PACA manual or document
prior to publishing.

ADF Automatic direction finder

AFC Automatic frequency control
AFIS Automatic Flight Inspection System
AGC Automatic gain control
AIP Aeronautical Information Publication
AM Amplitude modulation
ANSP Air navigation service provider
ATC Air traffic control
ATIS Automatic terminal information service
CATV Cable television
CVOR Conventional VOR
CMN Control motion noise
CW Continuous wave
DDM Difference in depth of modulation
DGNSS Differential global navigation satellite system
DME Distance measuring equipment
DVOR Doppler VOR
EIRP Equivalent isotropic radiated power
EMI/EMC Electromagnetic interference/compatibility
FM Frequency modulation
FMS Flight management system
GNSS Global navigation satellite system
GP Glide path
IF Intermediate frequency
IFR Instrument flight rules
ILS Instrument landing system
IM/MM/OM Inner/middle/outer marker
INS Inertial navigation system
ISM Industrial scientific medical
ITE Information technology equipment
ITU International Telecommunication Union
LF/MF/HF Low/medium/high frequency
LOC Localizer
MDS Minimum discernible signal
MHA Minimum holding altitude
MSL Mean sea level
MTBF Mean time between failures
MTBO Mean time between outages
NDB Non directional beacon

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 5

 Flight Inspection Manual for Radio Navigation Aids Initial

NOTAM Notice to Airmen

PAR Precision approach radar
PBN Performance-based navigation
PFE Path following error
PFN Path following noise
PLC Power line carrier
PM Phase modulation
POP Proof of performance
pp/s Pulse pairs per second
PRF Pulse repetition frequency
RDH Reference datum height
RF Radio frequency
RMS Root mean square
RNAV Area navigation
SARPs Standards and recommended practices
SDM Sum of depths of modulation
VFR Visual flight rules
VOR VHF omnidirectional radio range
VSWR Voltage standing wave ratio

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 6

 Flight Inspection Manual for Radio Navigation Aids Initial

FOREWORD

(1) This Document, Flight Inspection Manual for Radio Navigation Aids has been issued by the Public
Authority for Civil Aviation of Oman (hereinafter referred as PACA) under the provisions of the Civil
Aviation Regulation (CAR) 171, Aeronautical Telecommunication Service Provider.
(2) This Document sets out the procedures and criteria of the flight inspection, extension of flight inspection
period and approval of Radio Navigation and Visual Aids services; and
(3) The following standards have been basis for this Document:
(a) Oman Civil Aviation Law (CAL) Royal Decree 76/2019.
(b) CAR 171 (Aeronautical Telecommunication Service Provider)
(c) ICAO Annex 10 (Standards and Recommended Practices for Aeronautical Telecommunications).
(d) ICAO Doc 8071 (Manual on Testing of Radio Navigation Aids)
(4) The editing practices used in this document are as follows:
(a) ‘Shall’ is used to indicate a mandatory requirement and may appear in CARs.
(b) ‘Should’ is used to indicate a recommendation
(c) ‘May’ is used to indicate discretion by the AUTHORITY the industry or the applicant, as
appropriate.
(d) ‘Will’ indicates a mandatory requirement and is used to advise of action incumbent on the
Authority

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 7

 Flight Inspection Manual for Radio Navigation Aids Initial

Intentionally Left Blank

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 8

 Flight Inspection Manual for Radio Navigation Aids Initial

Table of Contents
DOCUMENT CONTROL SHEET ........................................................................................................................... 2
List of Effective Pages ............................................................................................................................................ 3
Glossary of Terms or Abbreviations ...................................................................................................................... 5
FOREWORD ......................................................................................................................................................... 7
Table of Contents .................................................................................................................................................. 9
1. GENERAL ................................................................................................................................................. 11
INTRODUCTION ........................................................................................................................................ 11
DEFINITION ............................................................................................................................................... 11
FACILITIY INSPECTION ............................................................................................................................... 11
INSPECTION PERIODIZATION .................................................................................................................... 13
PRIORITY OF FLIGHT INSPECTION ............................................................................................................. 14
GRACE PERIOD for PERIODIC FLIGHT INSPECTION .................................................................................... 15
EXTENTION OF FLIGHT INSPECTION PERIOD ............................................................................................. 15
UNIT OF MEASUREMENT .......................................................................................................................... 16
2. FLIGHT INSPECTION CREW AUTHORITY AND OBLIGATIONS .......................................................... 17
The Authority of Flight Inspection Crew ................................................................................................... 17
The Obligation of Flight Inspection Crew .................................................................................................. 17
3. GENERAL FLIGHT INSPECTION PROCEDURES .................................................................................... 18
The order of activities of the flight inspection implementation in general as follows: ......................................... 18
1. Pre-Flight Inspection..................................................................................................................................... 18
PRE-FLIGHT INSPECTION ........................................................................................................................... 18
PREPARTION BEFORE FLYING .................................................................................................................... 18
FLIGHT INSPECTION .................................................................................................................................. 19
ANALYSIS AND EVALUATION .................................................................................................................... 20
POST-FLIGHT INSPECTION ......................................................................................................................... 20
4. VERY HIGH FREQUENCY OMNIDIRECTIONAL RADIO RANGE (VOR) ............................................... 24
General ..................................................................................................................................................... 24
Flight Inspection performance parameter. ............................................................................................... 24
Flight Inspection Procedure ...................................................................................................................... 27
5. DISTANCE MEASURING EQUIPMENT (DME) ....................................................................................... 33
GENERAL ................................................................................................................................................... 33
FLIGHT INSPECTION PERFORMANCE PARAMETERS .................................................................................. 33
Flight Inspection Procedures ..................................................................................................................... 35
6. INSTRUMENT LANDING SYSTEM.......................................................................................................... 37

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 9

 Flight Inspection Manual for Radio Navigation Aids Initial

GENERAL ................................................................................................................................................... 37
FLIGHT INSPECTION PERFORMANCE PARAMETERS .................................................................................. 37
Flight Inspection procedure ...................................................................................................................... 47
CHARTS AND REPORTS.............................................................................................................................. 58
7. PRECISION APPROACH RADAR (PAR) ........................................................................................................ 60
8. NON-DIRECTIONAL BEACON (NDB) ........................................................................................................... 62
9. PERFORMANCE BASED NAVIGATION (PBN) .............................................................................................. 64
VOR for PBN.............................................................................................................................................. 64
DME for PBN ............................................................................................................................................. 64
10. SURVEILLANCE RADAR SYSTEM ................................................................................................................ 66
ATTACHMENT A : GROUND CHECK FORM........................................................................................................ 67

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 10

 Flight Inspection Manual for Radio Navigation Aids Initial

1. GENERAL
INTRODUCTION
Each Radio Navigation and Visual Aids operated for Air Navigation Services shall be
calibrated/tested/inspected in a manner periodically to ensure that Radio Navigation systems meet
the regulatory requirements of CAR 171 and the SARPs in ANNEX 10.
Radio Navigation Aids and Visual Aids, includes:
a. Ground Based Radio Navigation System
 VHF Omnidirectional Range (VOR)
 Distance Measurement Equipment (DME)
 Non-Directional Beacon (NDB)
 Instrument Landing System (ILS)
 VHF Marker Beacon (OM/MM/IM)
b. Surveillance Radar System
c. Visual Aids
 Precision Approach Path Indicator (PAPI)
 Visual approach Slope Indicator (VASI)

DEFINITION
The following term and meaning are applied in this document:
Flight Inspection Service Provider. Any organization that obtain certificates from Authority (PACA) to
conduct flight inspection for Radio Navigation Aids.
Flight Inspector. A Competent personal that authorized to examine the signal of Radio Navigation Aids
in space to ensure that it meet the standards in Annex 10, and state the operational status of equipment
being tested.

FACILITIY INSPECTION
The facilities calibration/testing or inspection of Radio Navigation and Visual Aids is defined in the
following categories:
a. Ground Inspection
b. Flight Inspection
1.3.1. Ground Inspection
Ground Inspection must be carried out by a trained CNS personnel using appropriate test equipment
at the facility site or at a point on the ground remote from the site.
Ground Testing shall cover:
a. Site proving; Tests carried out at proposed sites for the ground element of radio navigation
aids to prove suitability. Portable ground installations are used for this purpose.
b. Initial proof of performance: A complete inspection of the Facility after installation and prior
to commissioning to determine whether the equipment meets the Standards and
specifications.
c. Periodic: Regular or routine inspections carried out on a facility to determine whether the
equipment continues to meet the Standards and specifications.
d. Special: Tests after a failure of the facility or other circumstances that indicate special
testing is required or prior to Flight Inspection periodization. Special tests will often result
in appropriate maintenance work to restore the facility and in a special flight inspection, if
required.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 11

 Flight Inspection Manual for Radio Navigation Aids Initial

1.3.2. Flight inspection

Flight Inspection shall be carried out by Flight Inspection Service Provider approved by PACA.
Flight inspection shall cover:
a. Site proving:
A Flight Inspection conducted at the proposed site at the option of the responsible Authority to
determine the effects of the environment on the performance of the planned radio navigation aid.
b. Commissioning:
i) An extensive flight inspection following ground proof-of-performance inspection to establish
the validity of the signals-in-space. The results of this inspection should be correlated with
the results of the ground inspection. Together they form the basis for certification of the
facility.
ii) Commissioning Inspection for facilities installed on an unfinished runway.
In case of commissioning being carried out prior to the completion of ground construction
activities, including painting and lighting, Special Inspection Conditions will be implemented
only if flight inspector states that the rest of runway work shall not affect the navigational aids
performance and another special inspection will not be needed prior the facility being put
into operation.
c. Periodic:
Flight inspections to confirm the validity of the signals-in-space on a regular basis or after major
scheduled facility maintenance.
d. Special:
i) Flight inspections required as a result of suspected malfunctions, aircraft accident, etc.
Typically, it is necessary to test only those parameters which have or might have an effect on
facility performance. However, it may be economically advantageous in many cases to
complete the requirements for a periodic inspection.
ii) Equipment replacement of the same type and configuration as well as placed on locations
where the same physical condition, including the location of the antenna, is necessary to
conduct a special inspection. Items required for antenna change shall be done to a minimum
flight test performance required for the facility. Additional requirements of the inspection are
determined jointly by the flight inspector and ground technician.
iii) Equipment modification, reconfiguration and relocation on a facility that will affect the
radiant pattern is subject to a special flight inspection. Changes in type of antenna is classified
as reconfiguration. All commissioning inspections shall be carried out in accordance with the
reconfiguration of facilities, unless not required by flight inspector and facility maintenance
technician.
iv) Replacement of spare parts or modules affecting the value of parameters need to be
determined through flight inspection is subject to a special flight inspection
1.3.3. Post-Accident/Serious Incident Inspection.
This inspection is carried out at the request of the accident coordinator /investigator to verify that the
performance of the system is still eligible to use and can support instrument flight procedures.
(a) Follow-up
This inspection is a high priority and shall be implemented as soon as possible

(b) The flight inspector shall obtain the following information:

i) Configuration of equipment at the time of the accident, i.e. receiver, transmitter or radar
channel under operating conditions.
ii) The use of instrument flight procedures.
iii) Any additional information that helps in the inspection analysis.
Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 12
 Flight Inspection Manual for Radio Navigation Aids Initial

c. Inspection Procedure.
i) Coordinate with the facility maintenance technician to configure system according to
paragraph b (i).
ii) Complete periodic inspection checklist. Checking is done only on equipment and instrument
flight procedures used by the accident/incident aircraft. VOR or orbit track adjustment
TACAN (if any) is not necessary. It is strictly prohibited to perform facility adjustment after
an accident. Adjustment of equipment shall be performed on separate special conditions
inspection.
iii) If the system or procedure does not have periodic inspection requirements, evaluation shall
be done on the area where the accident occurred.
iv) Complete any additional materials requested by maintenance technician’s facilities, air
traffic control personnel (ATC) or accident coordinator / investigator.
v) In cases where the cause of the accident may be related to natural or man-made obstacles
on the earth’s surface (mountains, buildings etc.), the evaluation shall be done by
Aeronautical Study.
d. Confidentiality of accident/incident information.
Any findings on flight inspection or other information related to results of accident/incident
investigation shall be restricted and shared only with the approval of the accident Investigator.
Flight inspection results shall be submitted to PACA as soon as possible.

INSPECTION PERIODIZATION
a. Ground Check/Inspection.
(i) Periodic test, shall be conducted with the following periodization:

SR Type OF FACILITY FACILITY FUNCTION PERIOD

1. ILS LANDING 2 weeks
2. VOR HOMING 2 weeks
ENROUTE 4 weeks
3. DME HOMING 2 weeks
ENROUTE 4 weeks
CO-LOCATED GP-ILS 2 weeks
4. NDB LOCATOR 2 weeks
5. NDB HOMING/CHECK 4 weeks
POINT
6. RADAR APPROACH 2 weeks
ENROUTE 4 weeks
COMMUNICATION TOWER, APP, ACC 4 weeks
(VHF)
7. PAPI WITH ILS APPROACH 2 weeks
8. PAPI WITHOUT ILS APPROACH 4 weeks
9. VASI APPROACH 4 weeks
Table 1. Periodic Ground Test

(ii) Special test, shall be conducted in accordance with Flight Inspection periodization.
(iii) Ground Check/inspection shall be conducted using Ground Check/Inspection Form as per
attachment A of this document.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 13

 Flight Inspection Manual for Radio Navigation Aids Initial

b. Flight Inspection.
The validity period or periodization of flight inspection is as follows:
FLIGHT
FACILITY
SR NAME OF FACILITY INSPECTION
FUNCTION
PERIOD
1 ILS LANDING 6 Months
2 VOR HOMING/ENROUTE 12 Months
DVOR HOMING/ENROUTE 3 Years
3 CO-LOCATED VOR 12 Months
DME CO-LOCATED DVOR 3 Years
CO-LOCATED ILS 6 Months
4 NDB LOCATOR 6 Months
5
6 NDB HOMING/CHECK 12 Months
POINT
7 RADAR APPROACH If Required
ENROUTE If Required
8 COMMUNICATION TOWER, APP, ACC If Required
(VHF)
9 PAPI WITH ILS APPROACH 6 Months
10 PAPI WITHOUT ILS APPROACH 12 Months
11 VASI APPROACH 12 Months
Table 2. Periodic Flight Inspection

PRIORITY OF FLIGHT INSPECTION

Table 3 lists the priority of flight inspection to determine which mission will be conducted first when
two or more requirements are competing for limited flight inspection resources (flight
crew/aircraft/ground engineer or technician).

Priority Type of Service

1A Accident/Serious Incident Investigation and any facility which has
exceeded its inspection interval
1B Restoration of a commissioned facility after an unscheduled outage
and restoration of CAT II/ III ILS approach
1C Flight inspection of reported malfunctions or corrupted of the signal -
in-space
2A Commissioning inspection of new facility or new instrument flight
procedure
2B Periodic Inspection
3A Site Evaluation
3B Other Investigation
Table 3. Flight Inspection Priority List

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 14

 Flight Inspection Manual for Radio Navigation Aids Initial

GRACE PERIOD for PERIODIC FLIGHT INSPECTION

Air Navigation Service Provider must ensure that flight inspection of a commissioned Ground NAVAID
shall be completed within the grace period of 14 days calendar from the due date of Flight inspection.

EXTENTION OF FLIGHT INSPECTION PERIOD

In case flight inspection can’t be conducted within the grace period due to unforeseen circumstances
e.g. technical and/or operational issue, then ANSP shall submit a proposal to Authority requesting
approval for the extension of the Flight Inspection period.
Periodic flight inspections for NAVAID equipment may be extended by the authority up to the
following provisions:
a. For instrument of ILS (Instrument Landing System) a period of extension up to 3 months;
b. For VOR equipment (Very High Omnidirectional Range) as homing facility function a period of
extension up to 3 months;
c. For DME equipment (Distance Measuring Equipment) as homing facility function a period of
extension up to 3 months;
d. For VOR equipment (Very High Omnidirectional Range) as en-route facility function a period of
extension up to 6 months;
e. For DME equipment (Distance Measuring Equipment) as en-route facility function a period of
extension up to 6 months;
f. For NDB equipment (Non-Directional Beacon) as locator a period of extension up to 3 months;
g. For NDB equipment (Non-Directional Beacon) as homing/check point period of extension up to
6 months;
h. For PAPI equipment (Precision Approach Path Indicator) a period of extension up to 3 months;
i. For VASI equipment (Visual Approach Slope Indicator) a period of extension up to 6 months.
During the extension of Flight Inspection Period, ANSP shall:
(1) Conduct periodic Ground Check as mentioned in paragraph 1.3 (a) using Ground Check Form as
shown in Attachment A of this Manual.
(2) submit the Ground Check result of related facility to the Authority as reference to review and
evaluate the performance of facility during the proposed extension period;
(3) Continue in Conducting the maintenance activities according to the maintenance plan for the
facility, as well, the record the test result and monitor readings of critical parameters to indicate
that the equipment consistently meets performance requirements.
(4) Issue a NOTAM stating that the status of facility as:
“[Facility Name] Operating but ground checked only, awaiting flight Check”
When issuing the NOTAM, the ANSP shall indicate the validity period of the NOTAM according to
the approval issued by the Authority.
As it cannot be guaranteed that an “Operational Status” is always received after flight inspection it
is suggested that the ANSP publish the time frame as an estimated period and include the letters
EST after the expiry date and time of the NOTAM. In such cases the ANSP is required to coordinate
with the NOTAM Office (NOF) prior to the expiry time advising if the NOTAM requires extension,

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 15

 Flight Inspection Manual for Radio Navigation Aids Initial

cancellation or replacement with new criteria (i.e. if the facility returns to operation or is turned off
etc.).
If the ANSP does not include the EST letters in the NOTAM the NOTAM will automatically cancel at
the expiry date and time and the status of the facility will not be correctly notified to users.
Note: It is the responsibility of the ANSP to ensure the status of the NAV-AID is correctly published
and to ensure the correctness of all NOTAM.
1.7.1. FLIGHT INSPECTION AT NIGHT
Flight inspection may be conducted at night only in certain areas which have high densities of air traffic
during daylight hours. The following additional factors must be considered for night-time flight
inspection:
a) Effect of the environment on the radiated signal. The signals radiated by some types of radio
navigation aids are affected by propagation which differs between day and night.
b) Effect of environment on the navigation aid. The ground facility maintenance technician/
engineer should inform the flight inspector of any equipment variations, such as field monitor
performance which may change at night. The effects of the local environment, such as changes in
the position of reflecting obstacles, shall be considered.
c) Position reference. Flight inspection at night may use an independent reference system
including ground tracking equipment.
d) Evaluation of results. The flight inspector should indicate if there are differences from expected
measurements and indicate if these differences are caused by night conditions, problems with the
equipment or making the measurements at different positions.
e) Flight inspection reports. The flight inspection report should indicate whether the inspection
was made at night.
f) Types of flight. The inspection flights should be made in accordance with the guidance given in
this manual, with the exception of measurements that specifically need low-level flights. It is
recommended that at specific intervals an inspection is made under the same conditions as
prevailed at the time of commissioning.
g) Safety of flight. Flights should be conducted 300 m (1O00 ft.) above the level normally used for
daytime flight inspection in areas with terrain or obstacles. It will be necessary to change some
horizontal distances in order to retain the same vertical angle from the navigation aid, where this
is important to the measurements. Low-level below path (safety approach) glide path inspection
flights should not be made during the night or when the level of natural light is low. Flights should
normally be carried out in accordance with VFR.
UNIT OF MEASUREMENT
The references used in this manual (unless otherwise specified) are as follows:

Term Reference
Distance Nautical Mile
1 NM = 1.850 m
1 NM = 1.151 M
Airspeed and Groundspeed Knots
Bearing, Heading, Azimuth Radial, Direction Magnetic North
Information and Instruction
Altitudes Absolute

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 16

 Flight Inspection Manual for Radio Navigation Aids Initial

2. FLIGHT INSPECTION CREW AUTHORITY AND OBLIGATIONS

The Authority of Flight Inspection Crew
The flight inspection crew has the authority to:
a. Carry out flight inspections of Radio Navigation Aids (NAVAIDS) to determine that the navigation
service meets tolerance set out in this manual, and the facility may support flight procedures.
b. Report any hazard conditions during flight inspection.
c. Take action in accordance with the procedure.
d. Review, verify, and customize topography, patterns and data barriers (roads, railways, antennas,
towers, power lines, rivers, urban areas, etc.) contained on the flight map to evaluate the accuracy
and usability of navigation aids.
The Obligation of Flight Inspection Crew
The flight Inspector’s responsibility are limited to:
a. Conducting flight inspections in accordance with the procedures established by this manual;
b. Determining the adequacy of the system to meet its required functions;
c. Analyzing and evaluating the flight inspection data to enable a status classification to be assigned;
d. Certifying the signal-in-space of a NAVAID in accordance with the tolerances prescribed in this
manual;
e. Coordinating with engineering, maintenance, and/or Air Traffic Control;
f. Reporting the flight inspection results and status of the system to the ANSP;
g. providing the technical details for NOTAMs based on the flight inspection data;
h. Verifying the accuracy of NOTAMs and published information related to facility status;
i. Inspecting the flyability of instrument procedures prior to their publication;
j. Optimizing facility performance during flight inspections requiring adjustments by coordinating
with the ground engineer or technician;

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 17

 Flight Inspection Manual for Radio Navigation Aids Initial

3. GENERAL FLIGHT INSPECTION PROCEDURES

The order of activities of the flight inspection implementation in general as follows:
1. Pre-Flight Inspection.
2. Preparation before Flying
3. Flight inspection.
4. Analysis and Evaluation.
5. Flight inspection review and Reporting
6. Post Flight Inspection
PRE-FLIGHT INSPECTION
3.1.1. Status of Facility
Flight inspection should not be carried out until all facilities are installed and/or properly set and/or
ground calibrated, and operating normally.
3.1.2. Notification
a. The flight inspection service provider shall notify the Air Navigation Service Provider about the
Flight Inspection plan and Estimate Time Arrival (ETA) of aircraft.
b. The flight Inspection Service Provider shall coordinate with ANSP for any other notifications
that are required for the purpose of flight inspection i.e. field evaluation, commissioning,
periodical with monitors or inspections that require the support of the ground technician or
maintenance personnel.
c. Regular inspection of ILS without a monitor does not require initial coordination with the
maintenance personnel. This inspection must be carried out on transmitters that are in
operation. If there is nonconformity with tolerance, the flight inspector shall inform the
maintenance personnel and conduct flight inspection for back up or standby equipment.
d. NOTAM must be published if nonconformities have not been corrected.
PREPARTION BEFORE FLYING
Understanding between maintenance personnel and Flight Inspection crew is crucial to support the
smoothness of flight inspection. Coordination shall be established between Flight inspection crew and
maintenance personnel at times before, during, and after flight inspection.
The flight inspection crew shall give directions to the maintenance personnel about important steps
taken before implementation of flight inspection or commissioning and for special circumstances.
Efficiency and smoothness of Flight Inspection requires good preparation before flying and actions
from maintenance personnel. These preparations include:
a. Prepare two-way radio communications equipment and resources at facility locations.
b. Ensure that the facility is in normal operation and all parameters are in tolerance according to
technical specification requirement.
c. Ensure the presence of qualified technician to perform corrections and adjustments.
d. Prepare the means of transportation to transfer the calibration equipment and personnel.
e. Prepare accurate facility data for new facilities or relocated.
The following actions shall be conducted by Flight Inspection crew prior to flight inspection:
a. Ensure that all flight inspection equipment has been calibrated and can be operated.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 18

 Flight Inspection Manual for Radio Navigation Aids Initial

b. Gives direction to the maintenance personnel and/or ground technician.

c. Gives direction to the crew of the calibration aircraft.
d. Set up maps, charts, tools, data sheets, etc.
e. Review the status, limitations, and characteristics of the facility. Ensure that the publication and
recording of results from flight inspections which applicable previously, and all the restrictions
applied were accurate.
f. Providing direction to Air Traffic Control (ATC) personnel about the areas and altitude used for
flying maneuvers during flight inspections and possible changes.
FLIGHT INSPECTION
Flight inspection shall be carried out according to the procedures in this manual.
The following shall be considered during the flight inspection implementation
a. Expert. During the flight inspection, qualified personnel must be assigned to avoid errors of
equipment performance.
b. Standby Equipment. This is required to identify which system or transmitter is operating so
that the performance of each such equipment can be tested. If one unit of dual equipped facility
is found not according to tolerance, then the out of tolerance unit must be identified and shall
not be used in the service. The unit can be identified as transmitter number 1 or 2. Channel A or
B, serial number, etc.
c. Standby Power. During the commissioning /flight inspection. flight inspector shall check the
facility with the standby power (if it is installed with standby power), to ensure that performance
of the facility does not decrease with the standby power system and ensure that all parameters
are in tolerance. If the standby power is installed after flight commissioning / flight inspection,
then flight inspector shall check the facilities with standby power on next flight periodic
inspection.
The examination of standby power is not required for facilities equipped with batteries which
are constantly supplied by other resources.
Standby power replacement doesn’t require re-inspection.
d. Philosophy in the field. If in the implementation of flight inspection it is found that parameters
that do not meet the standards and tolerance, the flight inspector should provide assistance to
the ground engineer to attempt to resolve the issue.
e. Restrictions. When the facility parameters do not meet the tolerance or existing standards,
flight inspector shall carry out an inspection to determine the area that can be used by the facility.
This data is used as a basis for restriction, NOTAM, or to re-create a procedure.
f. Limitations of spectrum management. Facilities set in the limitation of spectrum
management is classified as "Restricted" and must be identified in the facility data sheet. This
restriction still applies although there is no disruption to facility performance. It is not allowed
to remove the limitation of spectrum management that based on the results of the flight
inspection.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 19

 Flight Inspection Manual for Radio Navigation Aids Initial

g. Incomplete Inspection. In case, the commissioning inspection of the facility must be terminated
before completing all the flight inspection procedure due to aircraft damage, weather, etc., flight
inspection crew must discuss the condition of the facility under inspection.
If the facility maintenance manual allows setting parameters without flight inspection, and there
are insufficient references on previous flight inspection, the equipment can be used in the
service. This inspection is classified as incomplete inspection until the procedure of flight
inspection completed.
If there is an item on the flight inspection checklist that cannot be set according to the tolerance
limit, the inspection must be stopped. The status of facilities is changed to "unusable", and
Inspections are classified as incomplete inspection until the rest of the flight inspection
procedure are completed.
ANALYSIS AND EVALUATION
Flight inspection data must be analyzed and evaluated during the implementation of flight inspection
in accordance with the value of tolerance which are set forth in this manual. Recording which is done
during the flight inspection shall be entered permanent into a facility performance record data.
Flight inspection recording data is created and provided to maintenance technicians for technical
analysis purpose. Aeronautical telecommunication service provider shall maintain the flight
inspection recording data.
Setting Omni-directional facility (VOR, TACAN, DF, NDB, etc.) shall be calculated through the addition
of algebra. The azimuth reference (AFIS, Theodolite, map) should always be positive (+), and the
azimuth reference of ground facilities must always be negative (-). So, if the VOR radial receiver is
090.5 and the AFIS / theodolite position 090.0, then error at facility -0.50. Setup errors can also be
understood i. e clockwise (positive) and counterclockwise (negative).
POST-FLIGHT INSPECTION
After completing the flight inspection, flight inspection crew shall perform the following actions:
(1) Advise the maintenance technician/engineer about the result of flight inspection. Flight
inspection of all facilities shall be reported to authorized personnel.
(2) Setting Facility status. Flight inspection shall set status facilities (see. 3.5.1.1). Flight inspection
also shall notify all notes about the status of the facility to authorized personnel.
(3) Preparing flight inspection report. Flight inspection reports must be accurate and clear in
describing performance and facilities characteristics. Report must be completed in accordance
with this Manual (see 3.5.1.2).

3.5.1. Flight Inspection Result (Classification), Certificate and Report

3.5.1.1. Flight Inspection Result.
The result of facility flight inspection shall be an operational status of facility, and classified as follows:
a. Usable; Available for the operational use, defined as:
i) Unrestricted: Providing safe, accurate signals-in-space conforming to established standards
within the coverage area of the facility.
ii) Restricted: Providing signals-in-space not conforming to established Standards in all
respects or in all sectors of the coverage area, but safe for use within the restrictions defined.
The facility that may be unsafe shall not be classified as limited or restricted under any
circumstance.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 20

 Flight Inspection Manual for Radio Navigation Aids Initial

b. Unusable; Not available for operational use as providing (potentially) unsafe or erroneous
signals, or providing signals of an unknown quality
The operational status of the facility as mentioned in above paragraph shall be determined by the
Authority.
The status determination by authority shall be referred to judgement (by the pilot) of the flyability of
the signal-in-space, analysis of airborne measurements of the facility by flight inspector and the
statement of readiness by authorized ground maintenance personnel of ANSP.
The flyability of the instrument procedures is assessed as part of the validation activity conducted in
accordance with the Quality Assurance Manual for Flight Procedure Design (Doc 9906), Volume 5 —
Validation of Instrument Flight The facility status classification and NOTAM indicate the boundaries
that can be applied to the facility. The facility status classification shows facility performance in
general based on flight inspection results. This classification only intended for maintenance and / or
facility users. NOTAM is required to inform the user of any restrictions on the facility.
When the range of equipment cannot be checked according to the standard the volume of flight
inspection services due to state borders or limited airspace, this facility shall be classified as
Restricted, with notes on reports to fly a limited range due border of the country. NOTAM and
publication actions shall indicate facilities as unusable in areas is not inspected.
3.5.1.2. Flight Inspection Report
Flight inspection reports shall contain the following minimum information:
a. General information with basic report, crew and facility items, such as:
(1) date(s) of inspection and next inspection due
(2) type of inspection, e.g. routine, annual, commissioning, site proofing and special;
(3) name and facility designation;
(4) facility identification, frequency assigned, nominal angle and nominal width (for ILS)
(5) manufacturer and type of system being inspected
(6) Type of antenna of system being inspected
(7) category of operation (facility);
(8) serial number of report/unique identifier;
(9) aircraft registration;
(10) wind conditions, to allow cross-wind to be established;
(11) names and functions of all personnel involved in the inspection;
b. Method of making each measurement (where alternatives are available); these may be referenced
to the operating instructions;
c. Results and tolerances;
d. Details of associated attachments, e.g. recordings (chart or graph)
e. Details of extra flights made necessary by system adjustments;
f. Assessment by the flight crew of the navigation facility performance;
g. Comments by the flight inspector;
h. Details of any immediately notifiable deficiencies;
i. Status section indicating the operational status of the facility;
j. Statement of conformance/nonconformance; and
k. Signatures of appropriate personnel.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 21

 Flight Inspection Manual for Radio Navigation Aids Initial

To reduce transcription errors, the report should be computer-generated by the flight inspection
system and include explanation of events, remarks and status of the equipment.
From the inspection report it should be possible to trace back the utilized facility database settings,
system calibration, antenna calibration diagrams, antenna lever arm corrections, cable loss and all
relevant data involved in or related to the calculations used.
Flight Inspection Service Provider shall submit Flight Inspection Interim/preliminary Report to the
Air Navigation Service Provider or Aerodrome Service Provider after completion the flight inspection,
before leaving the site.
Air Navigation Service Provider or Aerodrome Service Provider shall submit the interim report to
NOTAM Office with using a NOTAM format in accordance with the applicable regulation.
3.5.1.3. Flight Inspection Certificate
Flight Inspection Certificate shall be provided by Flight Inspection Service Provider as summary of the
implementation of flight inspection including performance and operational status for each flight
navigation facility.
Flight Inspection certificate shall content minimum the following information:
a. basic identification items such as the aircraft tail number, facility name, facility identifier,
frequency, category and type of inspection, date and time of inspection, names of the pilot and
engineer or technician;
b. an assessment reference conducted by the flight crew of the navigation facility performance;
c. comments by the flight inspector/equipment operator;
d. details of any immediately notifiable deficiencies;
e. statement of conformance/nonconformance; and
f. signatures of appropriate personnel.
The Final Report as well as Flight Inspection Certificate for the facility shall be submitted by Flight
Inspection Service Provider to Air Navigation Service Provider and Authority within 14 working days
after completion of the Flight Inspection.
3.5.1.4. NOTAM of Facility
a. The NOTAM of Facility Status.
(1) Air Navigation Service Provider must immediately draft NOTAM action whenever there is
cause of the facility classification to be restricted (Restricted) or revised from previous status.
(2) NOTAM of facility shall include name, type, component, and area/height that cannot be used.
The absence of elevation information or special distances will refer to all the altitude and
distance available, it is important to enter the information certain to avoid confusion.
(3) A NOTAM must be issued if the restriction will affect instrument flight procedures, minimum
approach, or ILS category authorization (CAT) II or III.
(4) Air Navigation Service provider must verify that the NOTAM issued is appropriate and correct
and published in the publication.
b. Notification of Change of Status
(1) Notification of a permanent change of the facility status is to be done through the appropriate
Aeronautical Information Publication (AIP); differences from Standards are to be notified to
ICAO and in the AIP.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 22

 Flight Inspection Manual for Radio Navigation Aids Initial

(2) Notification of temporary changes in the status of facilities are to be promptly and efficiently
declared. A change in the status of a commissioned facility as a direct result of ground or flight
inspection procedures, and resulting in a change of operational status
(“unrestricted/restricted/unusable”) or “unusable” designation, shall be advertised
immediately by air traffic control (ATC) personnel, and promptly by a Notice to Airmen
(NOTAM).
(3) A facility having an “unusable” status shall be removed from service and can operate only for
test or troubleshooting purposes. In such cases the facility identification shall be transmitted
as TST
(4) Particular attention shall be given to periodic or corrective maintenance procedures that
involve false guidance signals being temporarily radiated. These conditions shall be
coordinated with ATC and promulgated to users by NOTAM, before the procedures
commence.
c. Out-of-Tolerance backup equipment.
If one of the transmitters (of dual system equipment) has out of tolerance parameters, the normal
operation transmitter can be operated without NOTAM. However, the NOTAM data describing the
restriction must be reserved for maintenance technicians/engineer. In case of limited transmitter Is
used, the operation may issue a NOTAM.
d. Restricted Facilities.
The following rules shall be used in preparing NOTAM of facility Restrictions:
(1) Describe Radials or unusable bearing.
(2) Describes height and distance that cannot be used.
(3) VOR / DME / DF / NDB
Draw a radial / bearing from station in a clockwise direction (CW) direction, altitude in terms of
at above and below an MSL altitude, and distance in terms of outside or inside in units of nautical
miles (nm).
(4) Localizer / LDA / SDF / TLS azimuth.
Draw laterally in terms of degree of left or right inbound only and within nm of the threshold if
effect of signal limitation limits can be used closest to the threshold limit. Use the distance (in nm)
of the antenna to illustrate the restriction which affects the distance the facility uses. Describe the
height in the above or below the height (MSL). Additional reference of DME distance can be used
if DME is part of SIAP.
(5) Glide Slope / TLS Elevation.
Draw in degrees left or right only and inbound nm from threshold. Limitations related to altitude
must be in above or below of the MSL height. Make sure it is correct reflecting restrictions on the
volume of the original service. Additional reference to DME
3.5.2. INSTRUMENT FLIGHT PROCEDURE
The flyability of the instrument procedure of Ground NAV-AID is assessed as part of the flight
validation activity conducted in accordance with Quality Assurance Manual for Flight Procedure
Design (Doc 9906), Volume V – Validation of Instrument Flight Procedure.
The flight inspection crew must coordinate with the ANSP if the restrictions on NAVAIDs may have an
effect on the published instrument's flight procedures. The Specialist procedures shall:

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 23

 Flight Inspection Manual for Radio Navigation Aids Initial

a. Determine the impact of published instrument flight procedures.

b. Initiatives to propose NOTAMs for amendment or change delay the procedure.
c. Evaluating the NAVAID restrictions to determine whether such limits will have an effect on the
instrument flight procedure.

4. VERY HIGH FREQUENCY OMNIDIRECTIONAL RADIO RANGE (VOR)

This part provides guidance on the flight inspection requirement applicable to both CVOR and DVOR
type VHF Omnidirectional Range (VOR). Since the means by which VOR signals are produced vary
from one manufacturer to the other, broad guidelines are provided and adaptation to specific
equipment will be required.

General
VORs should meet all requirements to be classified as unrestricted. The Air Navigation Service
Provider shall, after proper coordination, prescribe the use of the facility on a restricted basis and
issue Notice to Airmen (NOTAM) accordingly when a specific area of a facility does not meet these
operating tolerances.

Flight Inspection performance parameter.

Summary of VOR Flight Inspection Requirement are listed in Table 4.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 24

 Flight Inspection Manual for Radio Navigation Aids Initial

Annex 10, Volume Doc 8071,

Parameter Measured Tolerance Uncertainty Inspection type
I, reference Volume I, reference

Rotation 3.3.1.1 2.3.4 Clockwise Correct C, P, S

Sensing 3.3.1.3 2.3.3 Correctness Correct C, P, S
Polarization 3.3.3.1 2.3.5 Deviation ±2.0° 0.3° C, P, S
Pattern 3.3.3 Deviation C, P, S
accuracy 2.3.9 to 2.3.11 ±2.0° 0.6°
Alignme 2.3.12 (2.3.47) ±3.5° 0.6°
nt 2.3.13 (2.3.47) ±3.0° 0.3°
Bends (PFE/PFN) 2.3.14 Flyable Subjective
Roughness and scalloping (CMN)
Flyability
Coverage 3.3.4 2.3.15 Power density -107 dBW/m2 3 dB C
Power density or field strength 2.3.16 (90 μV/m)*
At limits or operational
requirements
*(recommendation)
Modulation 3.3.5 2.3.17 Modulation depth up to 5º See Note. 1% C, P, S
9 960 Hz modulation (VOR without elevation 20 to 55%
voice modulation) 20 to 35%
9 960 Hz modulation (VOR with voice 25 to 35%
modulation)
30 Hz modulation
Modulation 3.3.5 2.3.17 Deviation ratio C, P
30 Hz FM deviation
ratio CVOR 16 ±1°
DVOR (below 5º 16 ±1°
elevation) DVOR (5º to >11°
40 º elevation)
Voice channel 3.3.6.2 2.3.18 Clarity Clear C, P
Identification 3.3.6.5 2.3.20 Clarity Clear C, P
2.3.21

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 25

 Flight Inspection Manual for Radio Navigation Aids Initial

Annex 10, Volume Doc 8071,

Parameter Measured Tolerance Uncertainty Inspection type
I, reference Volume I, reference

Speech effect on 3.3.6.7 2.3.19 No effect C, P

navigation Bearing Deviation 0.3°
Modulation Modulation 1%
Bearing monitor 3.3.7.1 2.3.22 to 2.3.25 Deviation ±1.0° 0.3° C
Table 4. Summary of VOR Flight Inspection Requirement

Note. — When modulation is measured during Flight inspection under strong dynamic multipath conditions, variations in the
received modulation percentage are to be expected. Short-term variations beyond these values may be acceptable.

Legend: C = Commissioning
P = Periodic as per flight inspection periodization 1.3 (b)
S = Site proving

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 26

 Flight Inspection Manual for Radio Navigation Aids Initial

Flight Inspection Procedure

4.3.1. Sensing
This check is required at the beginning of the flight inspection and need not be repeated. The bearing
of the aircraft from the station must be known. Select an appropriate radial and when the cross-pointer
is centered, the indicator should indicate “FROM”.
4.3.2. Rotation
Begin an orbit. The radial bearing as indicated should continually decrease for a counterclockwise
orbit, or increase for a clockwise orbit. Sensing should be checked before rotation. Incorrect sensing
might cause the station rotation to appear reversed.
4.3.3. Polarization effect
The polarization effect results from vertically polarized RF energy being radiated from the antenna
system. The presence of undesired “vertical polarization” should be checked by the “attitude effect”
and may be further investigated by either the “360” turn method” or the “heading effect” method.
4.3.4. Attitude effect method
The vertical polarization effect should be checked when flying directly to, or from, the facility, at a
distance of 10 to 20 NM. The aircraft should be rolled to a 30” bank, first to one side, then to the other,
and returned to a straight level flight. Track and heading deviations should be kept to a minimum.
Course deviation, as measured on the recording, is the indication of vertical polarization effect.
4.3.5. 30° bank, 360° turn method
a. Vertical polarization maybe checked by executing a 30° bank, 360° turn, 18.5 to 37 km (10 to 20
NM) from the antenna. The turn should begin from an “on-course” (toward the station) position
over a measured ground checkpoint.
b. The recording should be marked at the start of the turn and at each 90° of heading change until
the turn is completed. The turn should be completed over the starting point and the recording
marked. The recording should show a smooth departure from and return to the “on-course’’
position, deviating only by the amount that the aircraft is displaced from the original starting point
when the vertical polarization effect is not present. Other excursions of the cross-pointer may be
attributed to the vertical polarization effect. The effect of the wing shadowing the aircraft antenna
should be considered in evaluating the recording
4.3.6. Pattern accuracy
4.3.6.1. Alignment
a. Alignment can be determined by flying an orbit or by flying a series of radials. The altitude selected
for the flight should place the aircraft in the main lobe of the VOR.
b. The orbit should be flown at a height and range that allows the position reference system to
accurately determine the position of the aircraft. This will require low, close-in orbits for
theodolite-based position systems. Other automated systems will require the orbits to be
conducted at a greater range to achieve the required accuracy. The orbit should have sufficient
overlap to ensure that the measurement covers the complete 360°. The alignment of the VOR is
determined by averaging the error throughout the orbit. Judgement may be exercised where the
tracking of the orbit is interrupted to determine the effect of the lost information on the average
alignment.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 27

 Flight Inspection Manual for Radio Navigation Aids Initial

c. Alignment can also be determined by flying a series of radial approaches. These approaches
should be conducted at equal angular displacements around the facility. A minimum of eight
radials is considered necessary to determine the alignment of the VOR.
4.3.6.2. Bends
A bend is determined by flying a radial pattern and comparing the indicated course against a position
reference system. The error is measured against the correct magnetic azimuth of the radial. Deviations
of the course due to bends shall not exceed 3.5° from the computed average course alignment and shall
remain within 3.5° of the correct magnetic azimuths.
4.3.6.3. Roughness and scalloping error
Scalloping is a cyclic deviation of the course line. The frequency is high enough so that the deviation is
averaged out and will not cause aircraft displacement. Roughness is a ragged irregular series of
deviations. Momentary deviations of the course due to roughness, scalloping or combinations thereof
should not exceed 3.0" from the average course.
4.3.6.4. Flyability
Flyability is a subjective assessment by the pilot flying the inspection. Assessment of flyability shall be
performed on operational radials and during procedures based on the VOR.
4.3.7. Coverage
a. Coverage of the VOR is the usable area within the operational service volume and is determined
during the various checks of the VOR Additional flight checks are required to determine the
distance from the facility at which satisfactory coverage is obtained at the specified altitudes.
b. The coverage of a VOR can be affected by factors other than signal strength. Where out-of-
tolerance roughness, scalloping, bends, alignment, and/or interference render the facility
unusable in certain areas, a restriction should result which should be handled in the same manner
as restricted coverage due to lack of signal.
4.3.8. Modulation
The modulation of the 30 Hz reference, 30 Hz variable and 9 960 Hz subcarrier shall be measured
during the flight inspection. Note that the roles of the FM and AM signals are reversed between the
CVOR and the DVOR.
4.3.9. Identification
a. The identification signal shall be inspected for correctness, clarity, and possible detrimental effect
on the course structure. This check should be performed while flying on-course and within radio
line-of-sight of the station. Observe the course recording to determine if either code or voice
identification affects the course structure. If course roughness is suspected, the identical track
shall be flown again with the identification turned off. Maintenance personnel shall be advised
immediately if it is determined that the course characteristics are affected by the identification
signal.
b. The audible transmission of simultaneous voice/code identification signals shall appear to be
equal in volume to the user. The voice identification is not utilized during ground-to-air broadcasts
on the VOR frequency, but the coded identification must be audible in the background.
4.3.10. Bearing monitor
The requirements for checking the monitor are as follows:
a. during commissioning inspections; and

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 28

 Flight Inspection Manual for Radio Navigation Aids Initial

b. during subsequent inspections, if the alignment at the reference checkpoint has changed more
than one degree from the alignment last established and the monitor has not alarmed
The check is made over the reference checkpoint at the same altitude as that used to establish the
reference checkpoint. Position the aircraft inbound or outbound and activate the event mark exactly
over the checkpoint while the following course condition exist:
a. with the course in the normal operating condition;
b. with the course shifted to the alarm point;
c. with the course shifted to the alarm point to the opposite direction from b) above; or
d. with the course returned to the normal operating condition.
The course alignment shall be compared, in each of these conditions, by reference to the recordings to
determine the amplitude of shift to the alarm point and to verify the return to normal.
Check both transmitters in the same manner when dual monitors are installed. Both should be checked
on a systematic basis. Follow the procedure for single monitor check above, except in steps b) and c)
the course should be shifted in each direction until both monitors alarm. Determine the amplitude of
course-shift required to alarm both monitors
4.3.11. Reference checkpoint
A checkpoint shall be selected during the commissioning inspection on or close to the monitor radial
(usually 090 or 270 degrees) and located within 18.5 to 37 km (10 to 20 NM) of the antenna. This
checkpoint shall be used in establishing course alignment and shall serve as reference point for
subsequent inspections of alignment, monitors, course sensitivity and modulation measurements.
Course alignment and sensitivity shall normally be adjusted with reference to this checkpoint.
Adjustments made elsewhere will require a re-check of these parameters at this reference checkpoint.

The flight inspector shall record a description of the reference checkpoint that includes the azimuth
to the nearest tenth of a degree, the distance from the facility, and the mean sea level (MSL) altitude,
which is usually 460 m (1 500 ft) above the antenna. This data shall be revised any time the reference
check point is re-established.

The final course alignment error, measured at the reference checkpoint, shall be recorded on the
facility data sheet for subsequent reference in order to determine the necessity for a complete
monitor check.
4.3.12. Standby Power.
Stand by power, when installed, shall be checked during the commissioning inspection.
The following items shall be evaluated while operating on standby power:
a. course alignment (one radial);
b. course structure; and
c. modulations.
The inspections are to be performed when flying a portion of a radial with the station operating on
normal power, and then repeating the check at the same altitude and over the same ground track with
the station operating on standby power.
4.3.13. Standby Equipment
Both transmitters shall be checked against each required item of Table 4. These checks may be
performed using radial flights and a single alignment orbit.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 29

 Flight Inspection Manual for Radio Navigation Aids Initial

4.3.14. Complementary Facility.

Facilities associated with the VOR that complement operational use (such as marker beacons, DME,
lighting aids that support the visibility minima of an approach procedure, communications, etc.) shall
be inspected concurrently with the VOR and in accordance with applicable procedures.
4.3.15. Evaluation of Operational Procedures.
4.3.15.1. Radials
Radials used, or proposed for use, for IFR shall be inspected to determine their capability to support
the procedure. On commissioning inspections, a selection of radials proposed for IFR use shall be
inspected. The selection shall be based on the following criteria:
a. All radials supporting instrument approach procedures should be selected.
b. Radials should be selected from areas of poor performance indicated by the orbit inspection.
c. Any radials where the coverage may be affected by terrain should be selected.
d. At least one radial should be selected from each quadrant, if appropriate. In general, this should
include the longest and lowest radials.
e. Routine inspection requirements are contained in the following paragraphs.
4.3.15.2. En-route radials (airways, off-airway routes, substitute routes)
En-route radials shall be flown either inbound or outbound, along their entire length from the facility
to the extremity of their intended use, at the minimum altitude for the associated airway or route as
published. The minimum altitude for flying en-route radials, predicated on terminal facilities, is 300
m (1 000 ft) above the highest terrain or obstruction along the radial to a distance of 46.3 km (25 NM).
The aircraft shall be flown on the electronic radial and the position of the aircraft shall be recorded
using a position reference system.
Reference, variable and 9 960 Hz modulations and the vertical polarization effect shall be checked at
least once on each airway and direct-route radial. Signal strength, course deviation and aircraft
position should be recorded throughout the radial flight.
Course structure and alignment shall be determined by analysis of the recordings. The recordings
should also be analyzed for possible undesirable close-in or over-station characteristics to determine
that use of the facility for approach, holding, etc., is not adversely affected.
4.3.15.3. Terminal radials (approach, missed approach, standard instrument departure
(SID)
Approach radials shall be evaluated at a distance that includes the procedure turn, holding pattern
and missed approach on commissioning inspections. The approach radial shall be flown 30 m (100) ft
below specified altitudes. Site and commissioning inspections require two additional radials 5° either
side of the approach radial to be flown and analyzed with the same criteria as the approach radial.
This needs to be performed only if the approach radial shows performance near the set accuracy
requirement. Radials used to support SID procedures shall be evaluated to the extent to which they
are used.
4.3.15.4. Intersections
Adjacent facilities that provide intersections should be inspected to determine their capability to
support the intersection. Reliable facility performance and course guidance at the approved minimum
holding altitude (MHA) shall exist. Minimum signal strength shall exist for the radial(s) forming the
intersection within 7.4 km (4 NM) or 4.5°, whichever is greater, each side of the geographical location
of the intersection fix.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 30

 Flight Inspection Manual for Radio Navigation Aids Initial

Identification from each facility forming the intersection should be clear and distinct. The signal from
each facility should be free from interference at all altitudes below the maximum authorized altitude
for holding. A minimum reception altitude should be established for the intersection, which is
normally determined by the facility providing the weakest signal.

Note: All minimum en-route altitudes are to be corrected to and reported as true altitudes above
mean sea level. All intersections prior to being published and authorized for use are to be
flight inspected against the requirements stated above. Routine inspections of intersections
can be accomplished adequately by recording an airway radial of one facility and the
transition from other facilities forming the fix. Routine inspections can therefore be
conducted concurrently with airway radials. Departure from the airway radial that is being
inspected to evaluate another radial which is part of the fix is not required, unless detailed
investigations become necessary.

4.3.15.5. Cross-check radials

Commissioning and routine flight inspections of cross-check radials are not required provided there
is sufficient flight inspection data to support the publication of these radials. The radial(s) shall be
inspected prior to being authorized for use if cross-check radials are requested for use in areas outside
of the operational service volume of the facility(ies) for which supporting flight inspection data is not
available. Thereafter, flight inspections are not required.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 31

 Flight Inspection Manual for Radio Navigation Aids Initial

Intentionally Left Blank

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 32

 Flight Inspection Manual for Radio Navigation Aids Initial

5. DISTANCE MEASURING EQUIPMENT (DME)

This chapter provides guidance on Flight Inspection requirements applicable to the standard distance
measuring equipment (DME), as specified in Annex 10, Volume I, 3.5.
GENERAL
The flight inspection aircraft shall be equipped with a precision three-dimensional reference system,
a high quality DME interrogator, an oscilloscope with good timing capability, and a signal processing
capability. The flight inspection of DME can be performed separately or in parallel with the more
detailed check of the associated ILS, MLS, or VOR facility
In many cases, a DME is installed at the site of a VOR or ILS facility that is already operational. The
DME shall not be brought into unrestricted operational use until a commissioning flight inspection has
been performed.
FLIGHT INSPECTION PERFORMANCE PARAMETERS
When conducting a flight inspection of DME, independent of an associated facility, check the following:
1. Accuracy
2. Identification
3. Coverage
Summary of DME Flight Inspection requirement are listed in Table5.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 33

 Flight Inspection Manual for Radio Navigation Aids Initial

Annex 10, Doc

8071, Inspection type
Volume I,
Parameter reference Volume I, Measured Tolerance Uncertainty (See Notes 1-3)
reference
Coverage 3.5.3.1. 3.3.5 to Power density Signal strength such that field density ≥–89 dBW/m2 5 dB S ,C
Power density or field strength 2 3.3.8 (690 µV/m) at limits or operational requirements
3.5.4.1.5
.2
Accuracy 3.5.4.5 3.3.9 Distance ≤150 m 50 m S, C, P
≤75 m for DME associated with landing aids
Pulse shape 3.5.4.1.3 3.3.10 Time, Rise time ≤3 μs Duration 0.1 μs S, C, P
Amplitude 3.5 μs, ±0.5 μs Decay
time ≤3.5 μs
Amplitude, between 95% rise/fall amplitudes, ≥95% of 1%
maximum amplitude
Pulse spacing 3.5.4.1.4 3.3.11 Time, X channel: 12 ±0.25 μsY channel: 30 ±0.25 μs 0.05 μs S, C, P
Amplitude
Identification 3.5.3.6 3.3.13 Identification Correct, clear, properly synchronized N/A S, C, P
Reply efficiency 3.5.4.6 3.3.14 Change in Note areas where this changes significantly N/A S, C, P
efficiency,
position
Unlocks 3.3.15 Unlocking, Note where unlocking occurs N/A S, C, P
position
Standby equipment 3.3.16 Suitability Same as primary transmitter N/A S, C, P
Standby power 3.3.17 Suitability Should not affect transponder parameters N/A S, C, P

Table 5. Summary of DME Flight Inspection requirement

Notes:
1. Site proving tests (S) are usually carried out to confirm facility performance prior to final construction of the site.
2. Commissioning checks (C) are to be carried out before the DME is initially placed in service. In addition, recommissioning may be required
whenever changes that may affect its performance (e.g. variations or repairs to the antenna system) are made.
3. Periodic checks (P) are typically made as per flight inspection periodization 1.3 (b).

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 34

 Flight Inspection Manual for Radio Navigation Aids Initial

Flight Inspection Procedures

5.3.1. Coverage
DME coverage must be recorded or annotated and evaluated to the same coverage requirements as
the service (ILS/ VOR/ NDB, etc.) it supports. Coverage is validated on one transponder only.
5.3.1.1. Horizontal coverage
The aircraft is flown in a circular track with a radius depending on the service volume of the associated
facility around the ground station antenna at an altitude corresponding to an angle of elevation of
approximately 0.5° above the antenna site, or 300 m (1000 ft) above intervening terrain, whichever is
higher. If there is no associated facility, the orbit may be made at any radius greater than 18.5 km (10
NM). Since this flight is performed close to the radio horizon, it is possible to evaluate variations in
field strength by recording the AGC voltage. Flight inspection of the coverage at maximum radius and
minimum altitude, as prescribed by the operational requirements for the selected transponder, is
usually necessary only on commissioning checks, when major modifications are made in the ground
equipment, or if large structures are built in the vicinity of the antenna. The signal strength at the
aircraft is generally adequate to maintain the interrogator in the tracking mode. Thus, the equipment
itself can be used by the pilot for the desired orbit track guidance.
Note: Checking of the associated VOR can be performed on the same flight. For a terminal class
VOR, an orbit of 25 N) can be flown.
5.3.1.2. Vertical Coverage
The following flight inspection may be made to evaluate the lobe pattern of a DME transponder. The
Flight Inspection aircraft is used to perform a horizontal flight at approximately 1500 m (5000 ft) on
a bearing found suitable. The flight inspector records the RF-level or the AGC from the airborne
receiver. Airspace procedures based on the use of DME are evaluated at the minimum flight altitude.
The flight inspector verifies that the distance information is properly available in the aircraft at ATC
reporting points, along air routes.
5.3.1.3. Distance Accuracy
Check the accuracy of the DME distance information during inspection of radials, orbits, approach
procedures, and DME fixes. The exact mileage indication displayed on the distance indicators must be
noted on the recordings. Comparison of the scaled distance on the chart (converted to slant range) to
the distance indicated by the DME distance indicator at the various points may be made for accuracy
determination.
If the ground facility is emitting false reply pulses, erroneous distance information may be present.
This condition usually occurs within 25 miles of the antenna. Whenever actual false lock-ons are
experienced, the offending facility must be removed from service until this condition is remedied.
5.3.1.4. Identification
The identification must be checked for correctness and clarity, with the aircraft either in orbital or
radial flight. A DME associated with an associated facility will be checked for correct synchronization
of the two identification signals.
5.3.1.5. Standby Equipment
The standby DME transponder shall be spot- checked to ensure that it meets the same tolerances as
the primary equipment. This shall be done at the most critical points during the facility check in order
to obtain the comparison.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 35

 Flight Inspection Manual for Radio Navigation Aids Initial

5.3.1.6. Standby Power

During commissioning and periodic inspections, standby power may be checked by observing
operation and noting any appreciable differences in radiated signal characteristics that result from a
changeover to standby power. The transponder characteristics (identification, energy radiated, etc.)
shall not be degraded when switched to standby power.

5.3.1.7. Chart and Report

The parameters from a DME inspection shall be plotted on a graph relative to the distance or azimuth
from the DME under test.
When the DME is associated with ILS, MLS, or VOR, the DME details can be added to the report of this
facility. In other cases, a separate report can be issued.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 36

 Flight Inspection Manual for Radio Navigation Aids Initial

6. INSTRUMENT LANDING SYSTEM

This chapter provides instructions and performance criteria for inspecting localizer and glidepath
which operate in the VHF and UHF band as specified in Annex 10, Volume I, 2.7, 3.1 and Doc 8071
GENERAL
The ILS provides precision guidance to an aircraft during the final stages of the approach. The signals
can either be interpreted by the pilot from the instruments or be input directly into the autopilot and
flight management system.
Flight inspection of the associated facilities used as integral parts of the instrument landing system
(ILS) must be accomplished in accordance with instructions and criteria contained in their respective
chapters of this order or in other appropriate documents.

FLIGHT INSPECTION PERFORMANCE PARAMETERS

A summary of flight inspection requirements for ILS localizer, glide path and markers are given in
Tables 6, 7 and 8.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 37

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume Doc 8071, Measured Tolerance Uncertainty Inspection
I, reference Volume I, reference type

S C, C P
Identification 3.1.3.9 4.3.12 Morse code Proper keying, clearly audible to the limit of the range. Subjective x x
assessment
Voice feature 3.1.3.8 4.3.13 Audibility, Clear audio level similar to identification, no effect Subjective x x
DDM on course line. assessment
Modulation N/A 3.1.3.5 DDM, See Note 1.
3.1.3.5.3.6.1 Modulation, 0.002 DDM 0.001 DDM (x)
— Balance 4.3.14 Depth SDM 18% to 22% ±0.5% x x x
— Depth 4.3.15 <60% SDM within ±35° azimuth or actual coverage x x x
— Sum 4.4.8 sector for systems installed post January 2000
Displacement sensitivity 3.1.3.7 4.3.16 DDM Cat I: Within 17% of the nominal value Cat ±3 μA x x x
to 4.3.20 II: Within 17% of the nominal value Cat III: ±3 μA
Within 10% of the nominal value See Note ±2 μA
2. For nominal
150 μA input
Off-course clearance 3.1.3.7.4 4.3.21, DDM On either side of course line, linear increase to 175 μA, ±5 μA x x x
4.3.22 then maintenance of 175 μA to 10°. Between 10° and For nominal
35°, minimum 150 μA. Where coverage required 150 μA input
outside of ±35°, minimum of 150 μA except in back
course sector.
High-angle clearance N/A 4.3.23 DDM Minimum of 150 μA. ±5 μA x x
to 4.3.25 For nominal
150 μA input
Course alignment accuracy 3.1.3.6 4.3.26 DDM, Equivalent to the following displacements at the ILS x x x
to 4.3.28 Distance, reference datum:
Angle Cat I: ±2 m
Cat I: ±10.5 m (35 ft) Cat II: ±1 m
Cat II: ±7.5 m (25 ft)
[±4.5 m (15 ft) for those Cat II localizers
which are adjusted and maintained
within ±4.5 m]
Cat III: ±3 m (10 ft) Cat III: ±0.7m

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 38

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume Doc 8071, Measured Tolerance Uncertainty Inspection
I, reference Volume I, reference type

S C, C P
Phasing 4.3.39, DDM 10 μA of the modulation balance value. See Note 3. ±1 μA x x x
4.3.40
DDM increase linear 3.1.3.7.4 DDM >180 μA (Linear increase from 0 to >180 μA) x x
Voice no interference to basic 3.1.3.8 DDM, No interference. x x
function Speech
Phase to avoid voice null on 3.1.3.8.3.1 Speech No nulls. x x
dual frequency systems
Course structure 3.1.3.4 4.3.29 DDM Outer limit of coverage to Point A: 30 μA all categories See Annex 10, x x x
to 4.3.33 Volume I, Att. C,
See Annex 10, 2.1.5.
Volume I, Point A to Point B: From Point A to
Attachment C, Note to B, 3 μA
2.1.2.5 Cat I: Linear decrease to 15 μA decreasing
Cat II: Linear decrease to 5 μA to 1 μA
Cat III: Linear decrease to 5 μA

Beyond Point B:
From Point B to
Cat I: 15 μA to Point C E,
Cat II: 5 μA to Reference datum 1 μA
Cat III: 5 μA to Point D, then linear increase
to 10 μA at Point E.

See Note 4 for application of tolerances.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 39

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, reference type

S C, C P

Coverage (usable distance) 3.1.3.3 4.3.34 Flag status, -114 dBW/m2 (40 µV/m) in all parts of operational ±3 dB x x x
to 4.3.36 DDM coverage volume from 25 NM, when within the LOC
See Annex 10, Volume course sector and on GP:
I, Attachment C,
Figures C-7A and C-8A Cat I: -107 dBW/m2 (90 µV/m) on ILS from 10
(C-7B and C-8B for the NM to 30 m height
reduced
— Power density coverage case) Power Cat II: -106 dBW/m2 (100 µV/m) on ILS from 10
density NM, increasing to
-100 dBW/ m2 (200 µV/m) at 15 m height above
THR

Cat III: -106 dBW/m2 (100 µV/m) on ILS from 10

NM, increasing to
-100 dBW/ m2 (200 µV/m) at 6 m height above
THR,
-106 dBW/m2 (100 µV/m) along the length of the
runway

Note.— The conversion is stated in Annex 10,

Volume I, 3.1.3.3.2.
Polarization 3.1.3.2.2 4.3.37 DDM For a roll attitude of 20° from the horizontal: Cat I: ± 1 μA x x

15 μA on the course line

Cat II: 8 μA on the course line

Cat III: 5 μA within a sector bounded by 20 μA either side

of the course line.
Back course 4.3.41 DDM, Angle Not less than 3°. 0.1° x x
to 4.3.43
— Sector width N/A
— Alignment N/A DDM, Within 60 m of the extended centre line at 1 NM. ±6 m x x
Distance

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 40

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, reference type

S C, C P

— Structure N/A 4.3.79 DDM Limit of coverage to final approach fix: ±40 μA FAF to Annex 10, x x
1.85 km (1 NM) from threshold: ±40 μA Decreasing at a Volume I,
linear rate to: ±20 μA Attachment C,
2.1.4
— Modulation depth N/A Modulation 18% to 22% approximately 9 km (5 NM) from the ±0.5% x x
depth localizer.
See Note 1.
Monitor system 3.1.3.11 4.3.38 See Note 2.

— Alignment DDM, Monitor must alarm for a shift in the main course line from x x
Distance the runway centre line equivalent to or more than the
following distances at the ILS reference datum.

Cat I: 10.5 m (35 ft) 2m

Cat II: 7.5 m (25 ft) 1m
Cat III: 6.0 m (20 ft) 0.7 m

— Displacement sensitivity DDM, Monitor must alarm for a change in displacement x x

Distance sensitivity to a value differing from the nominal value by
more than:

Cat I: 17% ±4%

Cat II: 17% ±4%
Cat III: 17% ±2%

— Off-course clearance DDM Required only for certain types of localizer. Monitor must ±5 μA x x
alarm when the off-course clearance cross- pointer ±1 dB relative
deflection falls below 150 μA anywhere in the off-course
coverage area.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 41

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, reference type

S C, C P

— Power Power field Monitor must alarm either for a power reduction of 3 dB, ± 5 μA x
strength or when the coverage falls below the requirement for the
facility, whichever is the smaller change. For two-
frequency localizers, the monitor must alarm for a
change of ±1 dB in either carrier, unless tests have
proved that use of the wider limits
above will not cause unacceptable signal degradation
(>150 μA in clearance sector)

Table 5. Flight inspection requirements for localizer

Notes:
1. Recommended means by measurement is by ground check.
2. Recommended means of measurement is by ground check, provided that correlation has been established between ground and air measurement.
3. Optional, at the request of the ground technician, unless good correlation between airborne and ground phasing techniques has not been established.
4. Course structure along the runway maybe measured by flight inspection or by ground vehicle.

Legend: S = Site
C, C = Commissioning, Categorization
P = Periodic — as per flight Inspection periodization
N/A = Not applicable

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 42

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspecti type
reference Volume I, reference on

S C,C P

Angle 4.3.45, DDM, Cat I: Within 7.5% of nominal angle Cat I: 0.75% x x x
4.3.46 Angle Cat II: Within 7.5% of nominal angle Cat II: 0.75%
— Alignment 3.1.5.1.2.1 Cat III: Within 4% of nominal angle Cat III: 0.3%
of nominal
angle
— Height of reference datum 3.1.5.1.5 4.3.81 DDM Cat I: 15 m (50 ft) + 3 m (10 ft) (See Note 3) x
3.1.5.1.6 Cat II: 15 m (50 ft) + 3 m (10 ft) (See Note 3) 0.6 m
3.1.5.1.4 Cat III: 15 m (50 ft) + 3 m (10 ft) (See Note 3)

Displacement sensitivity 3.1.5.6 4.3.47 DDM, Symmetry: Cat I: 2.5% x x x

to 4.3.49 Angle Cat I: Between 0.07θ and 0.14θ above and below Cat II: 2.0%
— Value path Cat III: 1.5%
— Symmetry Cat I*: 0.12θ above and below path, within
±0.02θ
Cat II: 0.12θ above path, within
+0.02θ
and -0.05θ
Cat II: 0.12θ below path, within
±0.02θ
Cat III: 0.12θ above and below path, within
±0.02θ
* Recommendation

Value:
Cat I: Within ±25% of nominal displacement
sensitivity
Cat II: Within ±20% of nominal displacement
sensitivity
Cat III: Within ±15% of nominal displacement
sensitivity

Clearance 4.3.50 DDM, Not less than 190 μA at an angle above the horizontal of ±6 μA for a x x x
Angle not less than 0.3θ. If 190 μA is realized at an angle greater Nominal 190
— Below path 3.1.5.6.5 than 0.45θ, a minimum of 190 μA must be maintained at μA
least down to 0.45θ. input

— Above path 3.1.5.3.1 Must attain at least 150 μA and not fall below 150 μA
until 1.75θ is reached.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 43

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, reference type

S C,C P

Glide path structure 3.1.5.4 4.3.52 DDM See Note 5. x x x

4.3.79 Cat I: From coverage limit to Point C: 30 μA. Cat I: 6 μA
Cat II and III: From coverage limit to Point A: 30 μA Cat II: 4 μA
From Point A to Point B: linear decrease Cat III: 4 μA
from 30 μA to 20 μA.
From Point B to reference datum: 20
μA.
Modulation Modulation depth See Note 1.

— Balance 4.3.53 0.002 DDM 0.001 DDM (x)

— Depth 3.1.5.5.1 4.3.54 37.5% to 42.5% for each tone. 0.5% x x x
Obstruction N/A DDM Safe clearance at 180 μA (Normal), or at 150 μA Subjective x x x
(wide alarm). assessment
— Clearance 4.3.55
Coverage 3.1.5.3.1 4.3.56 Flag status Satisfactory receiver operation in sector 8° azimuth x x x
Attachment C, Figure 10 either side of the localizer centre line for at least 18.5
— Usable distance km (10 NM) up to 1.75θ and down to 0.45θ above the
horizontal, or to a lower angle, down to 0.3θ as
required to safeguard the glide path intercept
procedure.
— Power density or field 3.1.5.3.2 Power density -95 dBW/m² (400 µV/m) ±3 dB
strength
Monitor system 3.1.5.7 4.3.57, DDM, See Note 2. ±4 μA x x
4.3.58 Angle Monitor must alarm for a change in angle of -7.5/+10%
— Angle of the promulgated angle
— Displacement sensitivity DDM, Cat I: Monitor must alarm for a change in the angle
Angle between the glide path and the line below the glide
path at which 75 μA is obtained, by more than 0.037θ.
±4 μA
Cat II: Monitor must alarm for a change in x x
±1 dB
displacement sensitivity by more than 25%.
Cat III: Monitor must alarm for a change in
displacement sensitivity by more than 25%.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 44

 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, type
reference
S C,C P
— Power 4.3.58 Power Monitor must alarm either for a power reduction of 3 dB, x
or when the coverage falls below the requirement for the
facility, whichever is the smaller change.
For two-frequency glide paths, the monitor must alarm ±0.5 dB
for a change of ±1 dB in either carrier, unless tests have
proved that use of the wider limits above will not cause
unacceptable signal degradation.

Phasing N/A 4.3.59 No fixed tolerance. To be optimized for the site and N/A x x
to 4.3.65 equipment. See Note 4.

Table 7. Flight inspection requirements for Glide Path

Notes:
1. Recommended means of measurement is by ground check.
2. Recommended means of measurement is by ground check, provided that correlation has been established between ground
and air measurements.
3. This requirement only arises during commissioning and categorization checks. The method of calculating the height of the
extended glide path at the threshold is described in 4.3.81, Analysis — Reference datum height (RDH). For Category I
approaches on Code 1 and 2 runways, refer to 3.1.5.1.6 of Annex 10, Volume I.
4. Optional, at the request of the ground technician.
5. Tolerances are referenced to the mean course path between Points A and B, and relative to the mean curved path below
Point B.

Legend: S = Site
C, C = Commissioning, Categorization
P = Periodic — as per flight inspection periodization
N/A = Not applicable
Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 45
 Flight Inspection Manual for Radio Navigation Aids Initial

Parameter Annex 10, Volume I, Doc 8071, Measured Tolerance Uncertainty Inspection
reference Volume I, reference type

S C,C P

Keying 3.1.7.4 4.3.66 Keying Proper keying, clearly audible x x

3.1.7.5
Coverage 3.1.7.3 4.3.67 Signal Proper indication over the beacon or other defined x x x
to 4.3.71 level point.
— Indications distanc
e
— Field strength 3.1.7.3.2 Field strength When checked while flying on localizer and glide path,
coverage should be:
±40 m
OM: 600 m ±200 m (2 000 ft ±650 ft) ±20 m
MM: 300 m ±100 m (1 000 ft ±325 ft) ±10 m
IM: 150 m ±50 m (500 ft ±160 ft)
±3 dB
On a normal approach, there should be a well-defined
separation between the indications from the middle and
inner markers.

Measurement should use the Low sensitivity setting

on receiver. (Refer to Annex 10 for specific field
strength requirements)
Monitor system 3.1.7.7 4.3.72, An operationally usable indication should be obtained ±1 dB x x
4.3.73 for a reduction in power output of 50%, or a higher
power at which the equipment will be monitored. See
Note.
Standby equipment 4.3.74 Same checks and tolerances as main equipment. x x

Table 8. Flight inspection requirements for Marker

Note. — Alternatively, this can be checked by analyzing the field strength recording.
Legend: S = Site
C, C = Commissioning, Categorization
P = Periodic — as per flight inspection periodization
N/A = Not applicable
Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 46
 Flight Inspection Manual for Radio Navigation Aids Initial

Flight Inspection procedure

6.3.1. Localizer front course
6.3.1.1. Identification

The coded identification that is transmitted from the facility shall be monitored during the various
checks over all of the coverage area. The identification is satisfactory if the coded characters are
correct, clear and properly spaced. The transmission of the identification signal should not interfere
in any way with the basic localizer function. Monitoring the identification also serves the purpose of
detecting frequency interference, which is primarily manifested by heterodyne, or noise which affects
the identification.
6.3.1.2. Modulation

a. Modulation balance. Although the modulation balance is most easily measured on the ground,
it shall be measured as well from the air while radiating the carrier signal only. Position the
aircraft close to the runway center line and note the cross-pointer indication.
b. Modulation depth. The percentage of modulation shall be determined only while flying inbound
and on course at a point where the receiver signal strength corresponds to the value at which the
receiver modulation depth calibration was made, or on the ground during taxiing, backtracking
or lining-up operations when the aircraft is close to the runway center line. Therefore, this
requirement shall be fulfilled concurrently with the alignment check. If the receiver modulation
depth indications are influenced significantly by the RF level, measure the modulation depth near
Point A. (An adequate preliminary check of modulation can be made while the aircraft is crossing
the course during the displacement sensitivity check.) Modulation percentage is determined by
the use of calibration data furnished with the individual receiver.
6.3.1.3. Displacement sensitivity
There are two basic methods of measuring the displacement sensitivity:
1. approaches on the edges of the course sector.
2. crossovers or orbits through the course sector, at right angles to the extended runway center
line.
For special and commissioning flight inspections, the approach method is recommended. For all
flight inspections the discrepancy between ground and air measurement shall not exceed 10 per
cent of the nominal displacement sensitivity; where this degree of correlation is not achieved, the
reason for the discrepancy shall be resolved. On initial categorization, the displacement sensitivity
shall be set to the nominal value for that installation.

To determine the half-sector width in degrees using the approach method, fly the aircraft on either
side of the course line so that the average cross-pointer deflection is 75 (or 150) microamperes in
each instance. The average angular position of the aircraft, measured by the tracking device on each
side of the course line, will define the angular value of the half-sector width. The following formula
must be used to compute an equivalent angular change that corresponds to a displacement
sensitivity percentage change:
Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 47
 Flight Inspection Manual for Radio Navigation Aids Initial

New sector width = current sector width

(1+ change %)
Example calculation:
Wide sector (-17% displacement sensitivity) = 6.0 /(1 + (-0.17)) = 6.0/(1 - 0.17) = 6.0/0.83 = 7.23;
Narrow sector (+17% displacement sensitivity) = 6.0 /(1 + (+0.17) = 6.0/(1 + 0.17) = 6.0/1.17 = 5.13;

Note. — Deviation of the aircraft toward the runway extended center line will reduce the
accuracy of the measurements — normally the average cross-pointer deflection should be
within 15 (or 30) microamperes of the intended value.
The crossover or orbital method of displacement sensitivity measurement is typically used during
periodic inspections. In case of structure perturbation, the approaches on the edges of the course
sector are to be used during periodic inspections to minimize measurement errors.
When the crossover or orbital method is used, the measurement is made at a convenient known
distance from the localizer antenna, taking into account ground speed and the sampling rate and
delay of the navigation receiver and position reference system. To best calculate the displacement
sensitivity, it is necessary to use several samples from the linear DDM area and find the slope of the
straight line that fits the data. In order to provide an accurate reference for subsequent use, and to
correlate the results with the half-sector width measurement, this abbreviated procedure shall
initially be carried out during the commissioning or major inspection.
The following is an example of measuring course displacement sensitivity by this method. Fly a track
at right angles to the localizer course line so as to pass directly over the outer marker, or selected
checkpoint, at a height of 460 m (1 500 ft) above the localizer antenna site elevation. The flight
should begin sufficiently off course to assure stable airspeed prior to penetration of the course
sector. Follow the aircraft position with the tracking device and measure the angles at which -150, -
75, 0, 75 and 150 μA occur. The full sector from -150 to 150 μA should be flown so that linearity can
be assessed by examining the recordings.
6.3.1.4. Off-course clearance
The localizer clearance is checked to determine that the transmitted signals will provide the user with
the proper off-course indication and that there are no false courses. Conduct an orbital flight with a
radius of 9 to 15 km (5 to 8 NM) from the facility and approximately 1 500 ft above the antenna. Where
terrain is a factor, the height will be adjusted to provide line-of-sight between the aircraft and the
antenna.

Clearance shall be checked within the promulgated angular limits of coverage provided on either side
of the front course (typically 35 degrees), unless the back course is used for approaches. In such cases,
clearances will also be checked to the angular coverage limits of the back course. Outside of the
promulgated coverage, there may be false courses due to antenna pattern characteristics or
environmental conditions.

6.3.1.5. High angle clearance

The combination of ground environment and antenna height can cause nulls, or false courses, which
may not be apparent at all normal instrument approach altitudes. High altitude clearance shall
therefore be investigated upon:
a. initial commissioning;
Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 48
 Flight Inspection Manual for Radio Navigation Aids Initial

b. a change in the location of an antenna;

c. a change in the height of an antenna; or
d. installation of a different type antenna.

High-angle clearance is investigated within the angular limit of coverage provided, in the same manner
as for off-course clearance, at a height corresponding to an angle of 7 degrees above the horizontal
through the antenna. If the minimum clearance at this height, in an orbit of 5 to 8 NM, exceeds 150
microamperes, and the clearance is satisfactory at 1 000 ft, the localizer will be assumed as satisfactory
at all intermediate altitudes. Where the clearance is not satisfactory, additional checks will be made at
lower heights to determine the highest level at and below that which the facility may be used. In such
a case, procedural use of the localizer shall be restricted.
If approach altitudes higher than the height of 6 000 ft above the antenna elevation are required
locally, investigation shall also be made at higher heights to determine that adequate clearance is
available and that no operationally significant false courses exist.

6.3.1.6. Course alignment accuracy

The measurement and analysis of localizer course alignment shall take into account the course line
bends. The alignment of the mean course line needs to be established in the following critical region
before the appropriate decision height:
Category I : for at least 0.5 NM containing of ILS Point B
Category II : ILS Point B to ILS reference datum
Category III : ILS Point C to ILS Point D
A normal ILS approach shall be flown, using the glide path, where available. The aircraft’s position
shall be recorded using the tracking or position-reference system. By relating the aircraft average
position to the average measured DDM, the alignment of the localizer may be determined.
Where there are course line bends in the area being evaluated, they shall be analyzed so that the
average localizer alignment may be calculated.
6.3.1.7. Course structure
This is an accurate measurement of course bends and may be accomplished concurrently with the
alignment and displacement sensitivity checks. Recordings of approaches made during the course
alignment check and during the course sensitivity checks can be used for the calculation of course
bends.
The center, or mean, of the total amplitude of bends represents the course line for bend evaluation
purposes, and the tolerance for bends is applied to that as a reference. If the evaluation is made on
airborne data, low pass filtering of the position-corrected cross-pointer signal is necessary to
eliminate high-frequency structure components of no practical consequence.
The total time - constant of the receiver and recorder DDM circuits for the measurements shall be
referenced to an aircraft speed of 105 knots, for which the constant is approximately 0.5 second (refer
to Attachment C to Annex 10, Volume I, 2.1.6, for specific filter guidance). From the recording of
airborne measurements, the alignment for each zone for application of structure tolerances may be
determined as the average course position between the runway threshold and Point D, and separately
between Point D and Point E. To analyze the post-filtering low frequency spectral components, the
guidance found in Attachment C to Annex 10, Volume I, 2.1.3 and 2.1.5, shall be used, with the structure
tolerances referenced to the average course position in each zone.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 49

 Flight Inspection Manual for Radio Navigation Aids Initial

For the evaluation of a course center line structure, a normal approach shall be flown, using the glide
path, where available. For Category II and III localizers, the aircraft shall cross the threshold at
approximately the normal design height of the glide path and continue downward to the normal
touchdown point. Continue a touchdown roll until at least Point E. Optionally, the touchdown roll may
be conducted from touchdown to Point D, at which point a take- off may be executed, with an altitude
not exceeding 15 m (50 ft) until Point E is reached. These procedures shall be used to evaluate the
localizer guidance in the user’s environment. Accurate tracking or position reference shall be provided
from ILS Point A to the following points:
for Category I : ILS reference datum
for Category II : ILS reference datum
for Category III : ILS Point E
For Category III bend evaluation between the ILS reference datum and ILS Point E, ground
measurements using a suitably equipped vehicle may be substituted for flight inspection
measurements. This is the only area where a direct comparison between the ground and flight
measurement results is possible. Therefore, it is useful to perform this measurement with the flight
inspection aircraft to allow a comparison between the two measurement results.
If the localizer’s course is used for take-off guidance, bend measurements along the runway should be
made for any category of ILS.
Guidance material concerning course structure is provided in 2.1.3 to 2.1.6 of Attachment C to Annex
10, Volume I.
Note. — Course structure shall be measured only while the course sector is in its normal operating width.
6.3.1.8. Coverage
This check is conducted to determine whether the facility provides the correct information to the user
throughout the area of operational use. Coverage has been determined, to some extent, by various
other checks; however, additional procedures are necessary to complete the check of the coverage at
distances 18.5, 31.5 and 46.3 km (of 10, 17 and 25 NM) from the antenna.
Flights at appropriate heights are required for routine and commissioning inspections to ensure the
following coverage requirements are satisfied.
The localizer coverage sector is specified as follows (Annex 10, Volume I, 3.1.3.3.1):
The localizer coverage sector shall extend from the center of the localizer antenna system to distances
of:
46.3 km (25 NM) within plus or minus 10 degrees from the front course line;
31.5 km (17 NM) between 10 degrees and 35 degrees from the front course line;
18.5 km (10 NM) outside of plus or minus 35 degrees from the front course line if coverage is provided;
except that, where topographical features dictate or operational requirements permit, the limits may
be reduced down to 33.3 km (18 NM) within the plus or minus 10-degree sector and 10 NM within the
remainder of the coverage when alternative navigational means provide satisfactory coverage within
the intermediate approach area.
The localizer signals shall be receivable at the distances specified at and above a height of 600 m (2
000 ft) above the elevation of the threshold, or 300 m (1 000 ft) above the elevation of the highest
point within the intermediate and final approach areas, whichever is the higher; except that, where
needed to protect ILS performance and if operational requirements permit, the lower limit of
coverage at angles beyond 15 degrees from the front course line shall be raised linearly from its height
at 15 degrees to as high as 1350 m (4 500 ft) above the elevation of the threshold at 35 degrees from

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 50

 Flight Inspection Manual for Radio Navigation Aids Initial

the front course line. Such signals shall be receivable, to the distances specified, up to a surface
extending outward from the localizer antenna and inclined at 7 degrees above the horizontal.
Note. — Where intervening obstacles penetrate the lower surface, it is intended that guidance need not
be provided at less than the line-of-sight heights.”
In the specification above, all the localizer coverage requirements are based on the assumption that
the aircraft is heading directly towards the facility. When power density measurements are gain
compensated based on the aircraft antenna pattern polar diagram(s), arc profiles can also be
performed for coverage checks.
At periodic inspections, it is necessary to check coverage only at 31.5 km (17 NM) and 35 degrees
either side of the course, unless use is made of the localizer outside of this area. Arc profiles may be
flown at distances closer than this, provided an arc profile is flown at the same distance and altitude
during the commissioning inspection to establish reference values.

6.3.1.9. Polarization
This check is conducted to determine the effects of undesired vertically polarized signal components.
While maintaining the desired track (on the extended center line), bank the aircraft around its
longitudinal axis 20 degrees each way from level flight. The aircraft’s position shall be monitored using
an accurate tracking or position-reference system. Analyze the cross-pointer recording to determine
if there are any course deviations caused by the change in aircraft (antenna) orientation.
The effects of vertically polarized signal components are acceptable when they are within specified
tolerances. If this check is accomplished in the area of the outer marker, the possibility of errors due
to position changes will be lessened. The amount of polarization effect measured also depends on
polarization characteristics of the aircraft antenna, hence the vertical polarization effect of the aircraft
antenna should be as low as possible.
6.3.1.10. Localizer monitors
Localizer course alignment and displacement sensitivity monitors shall be checked by flight
inspection. A suggested method of flight inspection is given below:
a. Alignment monitor. Request the ground technician to adjust the localizer equipment to cause an
alarm of the alignment monitor. Fly the aircraft on the extended center line of the runway as
indicated by the position reference system and note the precise displacement in microamperes
from the recording in each condition of the alarm to the right and left of the center line. After the
course has been readjusted to a normal operating condition, its alignment should be confirmed.
b. Displacement sensitivity monitor. Request the maintenance technician to adjust the displacement
sensitivity to the broad and narrow alarm limits and check the displacement sensitivity in each
condition. This check should follow the normal displacement sensitivity check described in
6.3.1.3.
c. The crossover or orbital flight method shall be used only if good correlation with a more accurate
approach method has been established. After the alarm limits have been verified or adjusted, it is
also necessary to confirm the displacement sensitivity value in the normal operating condition.
Note.— During commissioning inspection or after major modifications, clearance shall be
checked while the displacement sensitivity is adjusted to its broad alarm limit. The values of
175 microamperes and 150 microamperes specified for application during normal
displacement sensitivity conditions will then be reduced to 160 microamperes and 135
microamperes, respectively.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 51

 Flight Inspection Manual for Radio Navigation Aids Initial

d. Power monitor. For single-frequency systems, the field strength of the localizer signal shall be
measured on course at the greatest distance at which it is expected to be used, but not less than
33.3 km (18 NM), while operating at 50 per cent of normal power. For two-frequency carrier
systems, the field strength of the localizer signal shall be measured on course at the greatest
distance at which it is expected to be used, but not less than 33.3 km (18 NM), while operating at
80 per cent of normal power for the both carriers. Power monitor requirements for single-
frequency and two-frequency systems are described in Annex 10, Volume I, 3.1.3.11.2 d) and e).
In addition, if ground inspections do not allow control of the structure along the center line, the
structure performances have to be met on course while operating at 80 per cent of normal power
for the carrier providing a radiation field pattern in the front course sector and 120 per cent for the
carrier providing a radiation field pattern outside that sector. If the alarm thresholds are lower than
these 1 dB values but not less than 3 dB, the structure performances have to be met at these lower
values (less than 100 per cent for the front course sector carrier and more than 100 per cent for the
other carrier).
The clearance areas have also to be checked, with the carrier providing a radiation field pattern in
the front course sector at 120 per cent of the nominal value or at the upper alarm limit, while the
carrier providing a radiation field pattern outside that sector at 80 per cent of the normal value or
at the lower alarm limit.

6.3.1.11. Phasing
The following phasing procedure applies to typical localizer systems. Alternative phasing procedures
in accordance with the manufacturer’s recommendations should be followed for other types of
localizers. To the extent possible, methods involving ground test procedures should be used, and
airborne measurements made only upon request from ground maintenance personnel. If additional
confirmation is desirable by means of a flight inspection, the following is a suitable example procedure:
Note.— Adjustments made during the phasing procedure may affect many of the radiated parameters.
For this reason, it is advisable to confirm the localizer phasing as early as possible during the
commissioning tests.
a. Measure the displacement sensitivity of the localizer if it is not already determined.
b. Feed the localizer antenna with the carrier equally modulated by 90 Hz and 150 Hz and load the
sideband output with a dummy load. Note the cross-pointer deflection as X (90) or X (150)
microamperes.
c. The aircraft should be flown at a suitable off-course angle (depending on the type of localizer
antenna used) during the phasing adjustment and should not be closer than 5.6 km (3 NM) from
the antenna.
d. Insert a 90-degree line in a series with the sideband input to the antenna and feed the antenna
with sideband energy.
e. Adjust the phaser until the deviation indicator reading is the same as in b) above.
f. Remove the 90-degree line, used in step d) above.
This completes the process of phasing the carrier with the composite sidebands. As an additional
check, displacement sensitivity should be rechecked, and compared with that obtained in step a)
above. The value obtained after the phasing adjustment should never be greater than the value
obtained before the phasing adjustment.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 52

 Flight Inspection Manual for Radio Navigation Aids Initial

6.3.2. Localizer back course

Where the localizer back course is to be used for approaches to landing, it shall be evaluated for
commissioning and at periodic intervals thereafter. Procedures used for checking the front course will
normally be used for the back course, the principal difference being the application of certain different
tolerances, which are given in Table 5. As a minimum, alignment, sector width, structure, and
modulation depth shall be inspected as well.
Under no circumstances should localizer equipment be adjusted to enhance performance of the back
course, if the adjustment would adversely affect the desired characteristics of the front course.

6.3.3. GLIDE PATH

Most glide path parameters can be tested with two basic flight procedures — an approach along the
course line, and a level run or orbit through the localizer course sector. Variations include approaches
above, below, or abeam the course line, and level runs left and right of the extended runway center
line. By selecting suitable starting distances and angles, several measurements can be made during a
single aircraft maneuver.
6.3.3.1. Glide path angle (site, commissioning, categorization and periodic)
The glide path angle may be measured concurrently with the glide path structure during these
inspections. To adequately check the glide path angle, an accurate tracking or positioning device shall
be employed. This is necessary in order to correct the recorded glide path for aircraft positioning
errors in the vertical plane.
The location of the tracking or positioning equipment with respect to the facility being inspected is
critical for accurate measurement. Incorrect siting can lead to unusual characteristics being shown in
the glide path structure measurements. The tracking device shall initially be located using the results
of an accurate ground survey. In certain cases, initial flight results may indicate a need to modify the
location of the tracking device.
At commissioning, the glide path angle shall be adjusted to be as near as possible to the desired
nominal angle. During periodic inspections, the glide path angle must be within the figures given in
Table 6.
6.3.3.2. Displacement sensitivity (site, commissioning, categorization and periodic)
The mean displacement sensitivity is derived from measurements made between ILS Point A and Point
B. Make approaches above and below the nominal glide path at angles where the nominal cross-
pointer deflection is 75 μA and measure the aircraft’s position using an accurate tracking device.
During these measurements, the average cross- pointer deflection should be 75 ±15 μA. Note that any
aircraft deviation toward the zero DDM course line will decrease the accuracy of the measurement.
The displacement sensitivity can be calculated by relating the average cross-pointer deflection to the
average measured angle.

6.3.3.3. Glide path angle and displacement sensitivity (routine periodic inspections)
The glide path angle and displacement sensitivity can be measured by using a level run or “slice”
method. This is only possible where the glide path is relatively free from bends so that there is a
smooth transition from fly-up to fly-down on the level run. This method shall not be used with systems
that have asymmetrical displacement sensitivity above and below the glide path.
Level run method. Fly the aircraft towards the facility at a constant height (typically the intercept
altitude), following the localizer center line, starting at a point where the cross-pointer deflection is
more than 75 μA fly-up (more than 190 μA recommended). This flight is usually made at 460 m (1 500

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 53

 Flight Inspection Manual for Radio Navigation Aids Initial

ft) above the facility unless terrain prevents a safe flight. If a different height is used, it shall be noted
on the flight inspection report and facility data sheet. During the flight, the aircraft’s angular position
shall be constantly tracked. By relating the recorded cross-pointer current to the measured angles, the
glide path angle and displacement sensitivity may be calculated. The exact method of correlating the
angle and cross-pointer measurements is dependent on the particular flight inspection system.
6.3.3.4. Clearance
The clearance of the glide path sector is determined from a level run, or slice, through the complete
sector during which the glide path transition through the sector is recorded. This measurement may
be combined with the level flight method of measuring the glide path angle and displacement
sensitivity.
This flight is made using the level run method, except that the run shall commence at a distance
corresponding to 0.3θ and shall continue until a point equivalent to twice the glide path angle has been
passed. The aircraft’s position shall be accurately measured throughout the approach. Cross-pointer
current shall be continuously recorded and the recording marked with all the necessary distances and
angles to allow the figures required in Table 6 to be evaluated. This recording shall also permit
linearity of the cross-pointer transition to be evaluated.
6.3.3.5. Glide path structure
Glide path structure is an accurate measurement of the bends and perturbations on the glide path. It
is most important to employ an accurate tracking or positioning device for this measurement. This
measurement may be made concurrently with the glide path angle measurement. Guidance material
concerning course structure evaluation is provided in 2.1.4 of Attachment C to Annex 10, Volume I.
6.3.3.6. Modulation
a. Modulation balance. The modulation balance is measured while radiating the carrier signal only.
Position the aircraft close to the glide path angle and note the cross-pointer indication. Flight
inspection of modulation balance should be conducted on specific engineering request only.
b. Modulation depth. This check can be best accomplished accurately while the aircraft is “on-path”;
therefore, final measurements are best obtained during angle checks. The measurements should
be made at a point where the receiver input corresponds to the value at which the receiver
modulation depth calibration was made. If the receiver modulation depth indications are
influenced significantly by the RF level, measure the modulation depth near Point A. For
measurement systems that do not provide separate modulation level outputs, preliminary
indications of modulation can be obtained during level runs at the time the aircraft crosses the
glide path. The depth of modulation (in per cent) can be obtained by comparing the glide path
receiver- flag-alarm-current to the receiver-flag-current-calibration data.
6.3.3.7. Obstruction clearance
Checks may be made beneath the glide path sector to assure a safe flight path area between the bottom
edge of the glide path and any obstructions. To accomplish this check, it is necessary to bias the pilot’s
indicator or use an expanded scale instrument. Position the aircraft on the localizer front course
inbound at approximately five miles from the glide path antenna at an elevation to obtain at least 180
μA “fly-up” indication. Proceed inbound maintaining at least 180 μA clearance until the runway
threshold is reached or it is necessary to alter the flight path to clear obstructions. This check will be
conducted during monitor checks when the path width is adjusted to the wide alarm limits during
which a minimum of 150 μA fly-up is used in lieu of 180 μA. When this check has been made during

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 54

 Flight Inspection Manual for Radio Navigation Aids Initial

broad path width monitor limit checks, it need not be accomplished after the path is returned to the
normal width of the normal approach envelope, except during the commissioning inspection.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 55

 Flight Inspection Manual for Radio Navigation Aids Initial

6.3.3.8. Glide path coverage

This check may be combined with the clearance check using the same flight profile. If a separate flight
is made, it is not necessary to continue the approach beyond the intercept with the glide path lower
width angle.
At site, commissioning, categorization and periodic checks this measurement shall be made along the
edges of a sector 8 degrees either side of the localizer center line. Coverage will be checked to a
distance of 18.5 km (10 NM) from the antenna. Coverage will be checked to a distance greater than
18.5 km (10 NM) to the extent required to safeguard the promulgated glide path intercept procedure.
Note. — Flight inspection alone is not sufficient to extend glide path coverage beyond 10 NM
(e.g. Frequency coordination).
6.3.3.9. Monitors
Where required, monitor checks may be made using identical measurement methods to those
described for glide path angle, displacement sensitivity and clearance. The level flight method for
angle and displacement sensitivity shall not be used if there is non-linearity in the areas being
evaluated.
Note. — If checks are required, see Note 2 of Table 7.
Power monitor (commissioning only). The field strength of the glide path signal shall be checked at
the limits of its designated coverage volume, with the power reduced to the alarm level. Alternatively,
if the monitor alarm limit has been accurately measured by ground inspection, the field strength may
be measured under normal operating conditions and the field strength at the alarm limit may be
calculated. This check may be made at the same time as clearance and coverage checks.
6.3.3.10. Phasing and associated engineering support tests
The glide path site test is made to determine whether the proposed site will provide satisfactory glide
path performance at the required path angle. It is extremely important that the site tests be conducted
accurately and completely to avoid re-siting costs and unnecessary installation delays. Because this is
functionally a site-proving test rather than an inspection of equipment performance, only one
transmitter is required.
A preliminary glide path inspection is performed upon completion of the permanent transmitter and
antenna installation, but prior to permanent installation of the monitor system. This inspection is
conducted on one transmitter as a preliminary confirmation of airborne characteristics of the
permanent installation. Additionally, it provides the installation engineer with data that enables the
engineer to complete the facility adjustment to the optimum for the commissioning inspection. This
requires the establishment of transmitter settings for monitor alarm limits. These settings may be
utilized by ground personnel to determine that the field monitor is installed at its optimum location
and that integral monitors recombining units are correctly adjusted to achieve the most satisfactory
overall monitor response.
The procedures for conducting various glide path engineering support tests are described below.
These checks will be performed by ground methods prior to the flight inspection, and airborne checks
will be conducted at the option of the ground technician. It is not intended that they will supplant
ground measurements, but that they will confirm and support ground tests. The details of these tests
will be included in the flight inspection report.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 56

 Flight Inspection Manual for Radio Navigation Aids Initial

a. Modulation balance. Although the modulation balance is most easily measured on the ground,
it may be measured from the air while radiating the carrier signal only. Fly a simulated “on-path”
approach recording the glide path indications. The average deviation of the glide path indication from
“on-path” should be noted for use in the phasing check. Ground personnel shall be advised of the result.
The optimum condition is a perfect balance, i.e. zero on the precision microammeter. If the unbalance
is 5 μA or more, corrective action shall be taken by ground personnel before continuing this test.
Note.— Level runs are not satisfactory for this test since shifting of centering may occur in low-
signal or null areas.
b. Phasing — transmitting antennas. The purpose of the phasing test is to determine that
optimum phase exists between the radiating antennas. There are several different methods of
achieving airborne phasing and these tests shall normally be made using the manufacturer’s
recommended methods. Where difficulty is experienced in achieving airborne phasing to a definite
reading by normal procedures, the flight inspector shall coordinate with the ground engineer to
determine the most advantageous area for conducting the phasing test. When this area and track are
determined, it shall be noted on the facility data record for use on future phasing tests of that facility.
c. Phasing — monitor system. Some types of glide path integral monitor need flight inspection
checks to prove that they will accurately reproduce the far-field conditions when changes occur in
transmitted signal phases. Procedures for making such checks shall be developed in conjunction with
the manufacturer’s recommendations.

d. Glide path antenna adjustment (null checks). These checks are conducted to determine the
vertical angles at which the RF nulls of the various glide path antennas may occur. The information is
used by ground engineer to assist them in determining the correct heights for the transmitting
antennas. The test is made with carrier signals radiating only from each antenna in turn. The
procedure for conducting this test is by level flight along the localizer course line. The angles of the
nulls will be computed in the same manner as the glide path angle is computed. The nulls are
characterized by a sharp fall in signal level.
6.3.4. MARKER BEACON
6.3.4.1. Keying.
The keying is checked during an ILS approach over the beacons. The keying is assessed from both the
aural and visual indication and is satisfactory when the coded characters are correct, clear and
properly spaced. The frequency of the modulating tone can be checked by observing that visual
indication is obtained on the correct lamp of a three-lamp system, i.e. outer marker (OM) — blue,
middle marker (MM) — orange and inner marker (IM) — white.
6.3.4.2. Coverage.
Coverage is determined by flying over the marker beacons during a normal ILS approach on the
localizer and glide path and measuring the total distance during which a visual indication is obtained
from a calibrated marker receiver and antenna or during which a predetermined RF carrier signal
level is obtained.
At commissioning:
a. The coverage shall be determined by making a continuous recording of the RF signal strength from
the calibrated aircraft antenna, since this allows a more detailed assessment of the ground beacon
performance. The visual indication distance should be noted for comparison with subsequent
routine checks.
For routine checks, measuring the distance over which the visual indication is received will be
sufficient, although the above procedure of recording signal strength is recommended.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 57

 Flight Inspection Manual for Radio Navigation Aids Initial

The signal strength recording shall be examined to ensure that there are no side-lobes of sufficient
signal strength to cause false indications, and that there are no areas of weak signal strength
within the main lobe.
b. A check shall be made that the center of the coverage area is in the correct position. This will be
over the marker beacon but in some cases, due to siting difficulties, the polar axis of the marker
beacon radiation pattern may have to be other than vertical. Reference shall then be made to the
operational procedures to determine the correct location of the center-of-coverage, with respect
to some recognizable point on the ground. The center-of-coverage can be checked during the
coverage flights described above, by marking the continuous recording when the aircraft is
directly over the marker beacon (or other defined point). On a normal approach there shall be a
well-defined separation (in the order of 4.5 seconds at 180 km/hr (95 kt)) between the indications
obtained from each marker.
At commissioning, categorization and annual inspections, a check shall also be made to ensure that
operationally acceptable marker beacon indications are obtained when an approach is made on the
glide path but displaced ±75 μA from the localizer center. The time at which the indication is obtained
will usually be shorter than when on the localizer center.
6.3.4.3. Monitor system
At commissioning, the coverage shall be measured with the marker beacon operating at 50 per cent of
normal power and with the modulation depth reduced to 50 per cent. An operationally usable
indication shall still be obtained; if not, the power shall be increased to provide an indication and the
monitor adjusted to alarm at this level.
Alternatively, the coverage under monitor alarm conditions can be determined by analyzing the field
strength recording as detailed in 6.3.4.2
6.3.4.4. Standby equipment
At commissioning, the standby equipment is checked in the same manner as the main equipment. It
will not be necessary to check both the main and standby equipment at each routine check, if the
equipment operation has been scheduled so that the routine checks are carried out on each equipment
alternately.
CHARTS AND REPORTS
The ILS flight inspection report shall record the conformance of the facility performance to the
Standards defined in Annex 10 as well as the equipment specific standards established by the
authorized flight inspection organization and the responsible ground maintenance organization.
Tables 6 and 7 list the parameters to be measured for localizer and glide path facilities, as well as
localizer back course approaches. Table 8 summarizes the parameters to be measured for ILS Marker
Beacons. It is recommended that the flight inspection report include an assessment of the parameters
listed in Tables 5 through 7, which are appropriate for the type of inspection. Flight inspection reports
shall allow for “As found” and “As left” results to be entered for routine documentation of the
adjustments made to facilities.
6.4.1. Report contents
The ILS flight inspection report shall contain the minimum information as mentioned in Chapter 3
paragraph 3.5.1.2.
The following are additional requirement shall be established for ILS flight Inspection report:
a. Selected receivers, antennas, reference source and other selectable parameters must be traceable
for each profile.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 58

 Flight Inspection Manual for Radio Navigation Aids Initial

b. Glide path (GP) aiming point offset calculations are terrain dependent and are normally calculated
and compensated for during commissioning.
c. Recordings and results should be configurable for ILS ground maintenance personnel in their
requested format, e.g. with DDM instead of µA, if so required.
d. A full set of applicable calculated data are presented in the result section of the enclosed report.
e. The results should be automatically checked against the tolerances specified and applied by ICAO
regulations (or otherwise towards stated regulations), and any out of tolerance situations should
be highlighted (i.e. * or red color).
f. The course and glide path structure calculation shall be based on a 95 per cent probability according
to Annex 10, Volume 1, Figure C-2.
g. As found and as left results, with adjustments and repeated profiles, shall be properly noted and
explained.
h. If specific tests are requested by ILS ground maintenance personnel, the report shall include results
accordingly.
i. If any unforeseen events occur, this shall be highlighted in the remarks section.
j. Current and any new restrictions applied shall be properly referenced in the remarks section

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 59

 Flight Inspection Manual for Radio Navigation Aids Initial

7. PRECISION APPROACH RADAR (PAR)

(RESERVED)

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 60

 Flight Inspection Manual for Radio Navigation Aids Initial

INTENTIONALLY LEFT BLANK

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 61

 Flight Inspection Manual for Radio Navigation Aids Initial

8. NON-DIRECTIONAL BEACON (NDB)

(RESERVED)

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 62

 Flight Inspection Manual for Radio Navigation Aids Initial

INTENTIONALLY LEFT BLANK

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 63

 Flight Inspection Manual for Radio Navigation Aids Initial

9. PERFORMANCE BASED NAVIGATION (PBN)

VOR for PBN

(RESERVED)

DME for PBN

(RESERVED)

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 64

 Flight Inspection Manual for Radio Navigation Aids Initial

INTENTIONALLY LEFT BLANK

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 65

 Flight Inspection Manual for Radio Navigation Aids Initial

10. SURVEILLANCE RADAR SYSTEM

(RESERVED)

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 66

 Flight Inspection Manual for Radio Navigation Aids Initial

ATTACHMENT A : GROUND CHECK FORM.

Date of Issue: 09-Apr-20 | Public Authority for Civil Aviation Page 67

 PUBLIC AUTHORITY FOR CIVIL AVIATION

ATTACHMENT A OF FLIGHT INSPECTION MANUAL

GROUND INSPECTION FORM
AERONAUTICAL TELECOMMUNICATION FACILITIES

MONTH : DATE :
AIRPORT :
EQUIPMENT : ILS LOCALIZER
SITE NAME :
EQUIPMENT FUNCTION :
TECHNICAL DATA : FREQ. : IDENTIFICATION :
LAST CALIBRATION : DATE :

GROUND INSPECTION MEASUREMENT

MEASUREMENT
SR PARAMETERS RESULT AFTER TOLERANCE TX1 TX2 REMARK
FLIGHT
CALIBRATION MEASUREMENT IN OUT OF MEASUREMENT IN OUT OF
RESULT TOLERANCE TOLERANCE RESULT TOLERANCE TOLERANCE
A BUILD IN TEST PARAMETER
1 RF POWER LEVEL POUT (Commissioning) - 3 db
2 COURSE ALIGNMENT 0.0000 DDM ±0,0015 DDM
Cat II: < 7.5 m

3 DEPTH OF MODULATION 20% ±2%

4 SUM OF MODULATION DEPTHS 40% ±4%
5 IDENTIFICATION MODULATION DEPTH 10% + 5%
6 MONITORING :
- COURSE SHIFT 7.5 m
- CHANGE IN DISPLACEMENT 0.17
SENSITIVITY
- CLEARANCE SIGNAL 150 µA
- TOTAL TIME OF OUT OF TOLERANCE 5s
RADIATION
- REDUCTION IN POWER -3 dB dari Comm
B ADDITIONAL TEST EQUIPMENT
1 RF POWER LEVEL Field strength Comm - 3 db
2 COURSE ALIGNMENT <7,5 meter (25 ft)
3 DISPLACEMENT SENSITIVITY 0,00145 DDM/m ±17%
4 SPURIOUS MODULATION <0,005 DDM peak to peak
5 DEPTH OF MODULATION 20% ±2%
6 SUM OF MODULATION DEPTHS Modulation depth <60%
7 ORIENTATION Correct
8 FREQUENCY Single frequency : 0.005%
Dual frequency : 0.002%

Halaman 1 /2
 GROUND INSPECTION MEASUREMENT
MEASUREMENT
SR PARAMETERS RESULT AFTER TOLERANCE TX1 TX2 REMARK
FLIGHT
CALIBRATION MEASUREMENT IN OUT OF MEASUREMENT IN OUT OF
RESULT TOLERANCE TOLERANCE RESULT TOLERANCE TOLERANCE
5kHz < Diff. < 14 kHz
CARRIER MODULATION FREQUENCY (90 Hz
9 and 150 Hz) ±1.5% (Cat : II)
10 IDENTIFICATION TONE FREQUENCY 1020 ±50Hz
11 IDENTIFICATION MODULATION DEPTH 5 % - 15%
C OTHERS
1 IDENTIFICATION SPEED 7 words / minutes
2 IDENTIFICATION REPETITION RATE > 6 times/minutes
3 INTERCONECTION
4 ANTENA
5 CHANGE OVER ( MAIN TO STANDBY ) 5s
6 INDICATORS
7 REMOTE CONTROL AND MONITORING SYSTEM

TECHNICIAN/ ENGINEER

CHIEF OF NAVIGATION SECTION

( )

Halaman 2 /2
 PUBLIC AUTHORITY FOR CIVIL AVIATION

ATTACHMENT A OF FLIGHT INSPECTION MANUAL

GROUND INSPECTION FORM
AERONAUTICAL TELECOMMUNICATION FACILITIES

MONTH : DATE :
AIRPORT :
EQUIPMENT : ILS GLIDE PATH
SITE NAME :
EQUIPMENT FUNCTION :
TECHNICAL DATA : FREQ. :
LAST CALIBRATION : DATE :

GROUND INSPECTION MEASUREMENT

MEASUREMENT
TX1 TX2
RESULT AFTER
SR PARAMETER TOLERANCE REMARK
FLIGHT
CALIBRATION OUT OF
MEASUREMENT RESULT IN TOLERANCE MEASUREMENT RESULT IN TOLERANCE OUT OF TOLERANCE
TOLERANCE

A. BUILT IN TEST PARAMETERS

1 RF POWER LEVEL Pout Comisioning - 3 db
PATH ANGLE 0.000 DDM ± 0.055 DDM
2 Within 7.5% of nominal angle
for Cat.II
3 DEPTH OF MODULATION 40% ±2,5%
4 SUM OF DEPTH OF MODULATION 80 % ± 5 %
(90 Hz + 150 Hz)
5 MONITORING :
- TOTAL TIME OF OUT OF TOLERANCE RADIATION 2s
- REDUCTION IN POWER -3 dB dari Comm
- PATH ANGLE Monitor must alarm for a
change in angle of 7.5% of the
promulgated angle.

- DISPLACEMENT SENSITIVITY Monitor must alarm for a

change in the angle between
the glide path and the line
below the glide path at which
75µA is obtained, by more
than 25% of path angle (for
Cat:II)

- CLEARANCE SIGNAL Monitor must alarm for

DDM<0.175 below path
clearance area

B. ADDITIONAL TEST EQUIPMENT

1 RF POWER LEVEL Field strength Comm - 3 db
2 PATH ANGLE 0.000 DDM ± 0.055 DDM
3 PATH WIDTH 0.175 DDM ± 0.050 DDM

Halaman 1 / 2
 GROUND INSPECTION MEASUREMENT

MEASUREMENT
RESULT AFTER TX1 TX2
SR PARAMETER TOLERANCE REMARK
FLIGHT
CALIBRATION OUT OF
MEASUREMENT RESULT IN TOLERANCE MEASUREMENT RESULT IN TOLERANCE OUT OF TOLERANCE
TOLERANCE

4 DEPTH OF MODULATION 40% ±2,5%

5 SUM OF DEPTH OF MODULATION 80 % ± 5 %
(90 Hz + 150 Hz)
6 ORIENTATION Correct
7 FREQUENCY Single : 0.005%
Dual : 0.002%
4kHz < Diff.<32kHz
8 CARRIER MODULATION FREQUENCY ±1.5% (for Cat:II)
C. OTHERS
1 INTERCONECTION
2 ANTENA
3 CHANGE OVER ( MAIN TO STANDBY ) 5s
4 INDICATOR LAMP&METERING
5 REMOTE CONTROL AND MONITORING
SYSTEM

TECHNICIAN/ENGINEER

CHIEF OF NAVIGATION SECTION

( )

Halaman 2 / 2
 PUBLIC AUTHORITY FOR CIVIL AVIATION

ATTACHMENT A OF FLIGHT INSPECTION MANUAL

GROUND INSPECTION FORM
AERONAUTICAL TELECOMMUNICATION FACILITIES

MONTH : DATE :
AIRPORT :
EQUIPMENT : VOR
SITE NAME :
EQUIPMENT FUNCTION :
TECHNICAL DATA : FREQ. : IDENTIFICATION :
LAST CALIBRATION : DATE :

MEASUREMENT GROUND INSPECTION MEASUREMENT

RESULT AFTER TX1 TX2
SR PARAMETER TOLERANCE REMARK
FLIGHT MEASUREMENT OUT OF MEASUREMENT OUT OF
CALIBRATION IN TOLERANCE IN TOLERANCE
RESULT TOLERANCE RESULT TOLERANCE
BUILT IN TEST MONITOR
1 CARRIER FORWARD POWER (COVERAGE) 3dB down
2 CARRIER REVERSE POWER (VSWR) ≤ 5%
3 IDENTIFICATION
a. speed 9 sec/words
b. repetition 2 kali/menit
c. clearness
4 FORWARD UPPER SIDE BAND POWER 3dB down
5 FORWARD LOWER SIDE BAND POWER 3dB down
6 FIELD DETECTOR INPUT
- BEARING field detector Az angle ± 1o
- MODULATION 30 Hz Reff 30 ± 2 %
- MODULATION 9960 Hz 30 ± 2 %
MONITOR SISTEM ALARM
- BEARING Az angle ± 1o
- MODULATION 30 Hz Reff 30 ± 2 %
- MODULATION 9960 Hz 30 ± 2 %
- IDENTIFICATION
8 BEARING CHEK (TO DVOR) :
Position 1

gcf nav 2006 1

Halaman 1 / 2
 MEASUREMENT GROUND INSPECTION MEASUREMENT
RESULT AFTER TX1 TX2
SR PARAMETER TOLERANCE REMARK
FLIGHT MEASUREMENT OUT OF MEASUREMENT OUT OF
CALIBRATION IN TOLERANCE IN TOLERANCE
RESULT TOLERANCE RESULT TOLERANCE
Position 2
Position 3
Position 4
Position 5

9 MANUAL CHANGE OVER SWITCH

10 INTERCONNECTION

11 CHANGE OVER TIME 10 Sec

12 INDICATORS

13 REMOTE MONITORING

TECHNICIAN/ ENGINEER

CHIEF NAVIGATION SECTION

( )

gcf nav 2006 1

Halaman 2 / 2
 PUBLIC AUTHORITY FOR CIVIL AVIATION

ATTACHMENT A OF FLIGHT INSPECTION MANUAL

GROUND INSPECTION FORM
AERONAUTICAL TELECOMMUNICATION FACILITIES
MONTH : DATE :
AIRPORT :
EQUIPMENT : DME
SITE NAME :
EQUIPMENT FUNCTION :
TECHNICAL DATA : FREQ. : IDENTIFICATION :
LAST CALIBRATION : DATE :

GROUND INSPECTION MEASUREMENT

MEASUREMENT
RESULT AFTER TX1 TX2
SR PARAMETER TOLERANCE REMARK
FLIGHT
CALIBRATION MEASUREMENT OUT OF MEASUREMENT OUT OF
IN TOLERANCE IN TOLERANCE
RESULT TOLERANCE RESULT TOLERANCE

1 Peak power output ± 1 dB from Nom.

2 Pulse spacing
a. INTEROGATION (X chanel) 12 ± 0.25 µs
b. REPLAY ( X chanel) 12 ± 0.25 µs
3 Variation of peak power in any pair of pulse ± 20%
4 Transponder Pulse repetition frequency (PRF) > 700 pps
5 Replay effisiensi > 70 %
6 Time delay ( X chanel) 50 uS ± 1,0 uS
7 Identification CLEAR
Tone pulse pair 1350 pulse
8 Monitor sistem alarm
a. Variation of replay Delay DME VOR< 1µ s
DME ILS < 0,5µ s
b. Spacing ± 0.25 µs
9 Monitor action Delay Delay < 10 s
10 MANUAL CHANGEOVER(MAINS/STANDBY)
11 INTERCONECTION
12 CHANGE OVER TIME max 10 SECONDS
13 INDICATORS
14 REMOTE MONITORING

TECHNICIAN/ENGINEER

CHIEF NAVIGATION SECTION

( )

gcf nav 2006 1