Software Installation / Preparation

It is VERY important that you setup/install the software in the following

order. Please DO NOT rush and follow the instructions carefully.

1. Run 'VC141_redist.x64.exe' and begin the ESYS Software Setup (click

T

through, accept all agreements, use default locations for all software file
ec

locations when prompted during setup).

2. Run 'E-Sys_Setup-3.30.1-49938.exe' and begin the ESYS Software
h

Setup (click through, accept all agreements, use default locations for all
ni

software file locations when prompted during setup).

c_

3. Copy/Paste 'psdzdata' folder to C:\data\psdzdata\ (delete existing

psdzdata folder prior copy/paste)
S
al

The sub-folders should be moved directly to C:\data\psdzdata\ as indicated

es

in the picture below:

(c
)
C
op
yr
ig
ht
3. Run the ESYS Launcher PRO Setup (Requires MS .NET Framework 4.0)
a. This is the program you should use to run ESYS. Do not use the icon that
the ESYS installer provides to launch the program, instead use the icon that
the Launcher PRO provides.

Windows 10 might need to disable Windows Defender.

T
ec

If you reinstall your Windows OS you will need a new

activation code!
hn

The app won't work on Windows 10 build 1809 (all other builds
are ok)! Please contact me on WhatsApp on 07572426877 to fix this!
ic
_S

PLEASE DO NOT REQUEST ANY CODING JOBS TO BE DONE!

al
es
(c
)
C
op
yr
i gh
t
 T
E-SYS LAUNCHER PRO ACTIVATION

ec
hn
Place the token from 'TOKEN' folder of DVD in C:/Data Folder

ic
Open E-Sys Launcher Pro and select the path to E-Sys and then select the token from C:/Data folder

_S
al
es
(c
)
C
op
yr
ig
Enter the PIN: 00000 and press Launch Now

ht
 T
ec
You will see a code (Request Code).

hn
Copy this code CORRECTLY.

ic
It cost me £10 to generate, so MAKE sure is COPY and PASTE only to

_S
eBay message and send over to me!

al
NO manual type of this code, Copy&Paste ONLY!

es
SEND IT TO ME over eBay message ONLY (NO telephone texting) and

(c
I will get back to you ASAP with correct activation code for the

)
Launcher.

C
op
The launcher will work with
E-Sys up to the 3.30.1 version. The token is valid for 10 years. NO

yr
REFUND IF SEND WRONG CODE!

ig
ht
 BE SURE TO RUN ESYS from the ESYS LAUNCHER SHORTCUT … DO NOT USE THE
SHORTCUT THAT WAS CREATED BY THE ESYS INSTALLER!!!

4. Before we begin, here’s the MOST IMPORTANT PIECE OF INFORMATION THAT YOU NEED WHEN CODING

Under NO CIRCUMSTANCES SHOULD YOU EVER PRESS THE BUTTON “Code Default Values”
T

See BELOW for the location of that button in the Expert Mode; Coding Screen in ESYS
ec
hn
i c_
S
al
es
(c
)
C
op
y

CODING TUTORIAL NOW BEGINS

ri
gh

Step 1: Connect cable to computer then to car (Ensure that your car’s engine is running during coding)

Step 2: Wait until LAN network adapter in task bar has established limited network capability (no screenshot)
t

To validate that the cable has a proper connection to the car, open up the LAN properties in Windows. The adapter should be
set to obtain IP Address via DHCP (You can NOT set a STATIC IP Address for LAN Adapter)

If you have a proper connection, your IP Address should be: 169.xxx.xxx.xxx

Remember to DISABLE Anti-Virus and Firewall Programs, which are KNOWN to interfere with ESYS communication via
Ethernet / LAN connection.
Step 3: Open E-Sys
T
ec
hn
ic
_S
al
es

Step 4: Click the Connect button

(c
)
C
op
yr
i
gh
t
Step 5: Select F series you are working on, my case F10=F010 Project … then select:
Connection via VIN and click “Connect”

DO NOT USE ANY CONNECTION THAT SAYS “_DIRECT” at the end of the description

F001 – 7-Series (all, including Alpina variants) & 5-Series GT Models Only
F010 – 5-Series; 6-Series (including ///M variants and Alpina vairants)
F020 – 2, 3, 4 Series (all) (including ///M variants and Alpina variants)
T

F025 – X3, X4, X5, X6 (all) (including ///M variants)

F056 – 2014+ Mini Cooper (all variants with iDrive controller)
ec

I001 – i3, i8 (all variants)

hn
i c_
S
al
es
(c
)
C

Step 6: Click “OK”

op
y ri
gh
t
 Step 7: Click “Read”
T
ec
hn
ic
_S
al
es

Note: Option to save or not to save

Step 8: Right click FA, select “Activate FA”

(c
)
C
op
yr
ig
ht
Activating FA, just wait till it finishes. Once finished, FA should show (active) in green. If not, try again.
T
ec
hn
i

Note: If you do not activate FA as described in Step 8, you will receive this message
c_
S
al
es

Step 9: Click "Read (ECU)"

(c
)
C
op
yr
i gh
t
Step 10: Select CAFD (only one with a green Check mark) file under the module you want to read and
select “Read Coding Data” …. (Note: the ACSM ECU has 3 with green check marks … pick first one)
T
ec
hn
ic
_S
al
es
(c
)
C
op
yr
ig
ht
Step 11: Error Report, Click “Close”

You want to see that CAFD_xxxxxxxx_xxx_xxx_xxx.ncd was generated as shown below:

T
ec
hn
i c_
S
al
es
(c
)
C
op
yr
i
gh
t
Step 12: New option under CADF, a folder. Expand the folder by clicking + and right click that file, Select “EDIT FDL”
T
ec
hn
ic
_S
al
es

Step 13: Browse the folders till you find your option, I want option KOMFORTSCHLIESSUNG_FB
(c
)
C
op
y ri
g ht
Step 14: Factory option set to nicht_active. Right click, select “Edit”
T
ec
hn
ic
_S
al
es

Step 15: Select option desired, in this case, select “aktiv”

(c
)
C
op
yr
ig
ht
Step 16: Once all changes have been made, Click the “Save” icon
T
ec
hn
ic
_S
al
es

Step 17: Once saved, click the green back arrow

(c
)
C
op
yr
ig
ht
Step 18: Select the CAFD file that you just edited and then click “CODE FDL”
T
ec
hn
i c_
S
al
es

Step 19: Coding FDL (progress)

(c
)
C
op
yri
gh
t
 Step 20: After it completes, Click “Close”
T
ec
hn
i c_
S

Step 21: Error report will open, view and click “Close” (or save if necessary)
al
es
(c
)
C
op
yr
ig
ht

Cycle key and test for function. In my case, “0 errors” so it should work. I tested the new function
and windows rolled up via remote by pressing and holding the lock button.
 How to: Change Werte Values
Continuing from FDL CODING GUIDE above (after step 13)

Step 14b: This time right click on the werte value, Click “Edit”
T
ec
hn
i c_
S
al
es
(c
)
C
op
y
ri
gh
t
 15b: The option to change the value is in the lower window. Replace current value with new, Click the button on the right.
T
ec
hn
ic
_S
al
es

Step 16b: Save

(c
)
C
op
yr
i gh
t

Step 17b: Proceed to Step 18 in the FDL Coding Guide above and follow to the end.
 T
How to change FA (VO) in F-series car

ec
Version 8-24-2013

hn
Connect to the car by clicking icon at the top.

ic
_S
al
es
(c
)
C
op
yr
i
gh
1

t
 T
Select the correct TargetSelector, e.g. F010 (not F010_DIRECT) for an F10

ec
Select “Connection via VIN" and press the “Connect” button.
(Ignore the Vehicle-Specific parameter options.)

hn
Click OK in the popup box which appear when connection established.

ic
_S
al
es
(c
)
C
op
y ri
gh
2

t
 T
ec
Select "Expert Mode“.
Click on the "Coding" tile.
In Vehicle Order Box, click on the "Read" button. This will display the car’s FA .

hn
i c_
S
al
es
(c
)
C
op
yr
ig
ht
3
 T
ec
Click on the “Save” button.

hn
ic
_S
al
es
(c
)
C
op
yr
ig
ht
4
T
ec
Create a file name and Save it.
(Note: In this example the file name is “SAT”)

hn
i c_
S
al
es
(c
)
C
op
yr
ig
ht
5
 T
ec
Click on the “Edit” button.

hn
i c_
S
al
es
(c
)
C
op
yr
i
gh
6

t
 T
ec
The view will automatically change to FA-editor.

h ni
c_
S
al
e s
(c
)
C
op
yr
i
gh
7

t
 T
Expand the FAList folder system on left until SALAPA-Element is

ec
visible. Click on SALAPA-Element to select it.
You will see the SALAPA-Elements in the window at the bottom

h ni
c_
S
al
es
(c
)
C
op
yr
i gh
8

t
 T
Delete or add Elements directly into the bottom window.

ec
In this example 205 is highlighted and will be deleted. The
syntax is alpha-numeric and commas only, no spaces.

hn
ic
_S
al
es
(c
)
C
op
y ri
gh
9

t
 T
2TB has been added (and is highlighted for illustration purpose

ec
only.) Note that 205 is gone.
The syntax is to add new elements in alphabetical order.

hn
ic
_ S
al
es
(c
)
C
op
yr
ig
ht
10
 T
ec
Click on the Save Changes Icon at the upper right corner of the lower window.

hn
ic
_S
al
es
(c
)
C
op
yr
i gh
11

t
 T
The edited FA must be verified before it can be written to

ec
car. Right-click on FA and select Calculate FP.
If the FA has any errors, an error pop-up will be shown.

hn
After FP is calculated, WITHOUT ERROR, save the new FA.

ic
2

_S
1

al
es
(c
)
C
op
yr
i
gh
12

t
 T
ec
The new FA has been saved

hn
ic
_S
al
es
(c
)
C
op
yr
ig
ht
13
 T
Select “Expert Mode”

ec
Click on the “VCM” tile.
Load your saved FA file

h
Right-click on FA and Calculate FP again.

ni
c_
S
2

al
es
(c
)
C
op
1

y ri
g
ht
14
 T
Select the “VCM Master” tab Click
on the “Write FA FP” button.

ec
New FA will be written to the car.

h ni
c_
S
al
es
(c
)
C
1

op
2

yri
gh
15

t
 T
ec
What Next?
hn
For the new FA to be used for configuring ECUs,

ic
follow these steps:

_S
(Skip this if you have just completed the previous page)
Connect => Select "Expert Mode“

al
(If you have just completed the previous step, or are continuing from the previous

es
page, start here)
Click on "Coding" button.

(c
Read FA (VO).
Activate FA (VO).

)
Read SVT (…

C
Right-Click on ECU (the ECU itself not the underlying CAFD).

op
Select CODE.
Repeat for all ECUs applicable to your project

yr
ig
h t