Scribd
Upload
2K views

110v DC System

The document discusses the components and operation of a 110V DC power system. The key components are batteries, a battery charger, and loads. Batteries produce voltage through chemical reactions between electrodes and electrolytes. Common types include alkaline and nickel-cadmium batteries. Batteries provide power to loads but must be recharged, which is done by connecting them to a battery charger that converts AC power to DC and injects current into the batteries. Battery chargers are rated by their maximum current output and include components to monitor voltage, current, and electrolyte levels.

Uploaded by

Dani Khalid John
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
2K views

110v DC System

The document discusses the components and operation of a 110V DC power system. The key components are batteries, a battery charger, and loads. Batteries produce voltage through chemical reactions between electrodes and electrolytes. Common types include alkaline and nickel-cadmium batteries. Batteries provide power to loads but must be recharged, which is done by connecting them to a battery charger that converts AC power to DC and injects current into the batteries. Battery chargers are rated by their maximum current output and include components to monitor voltage, current, and electrolyte levels.

Uploaded by

Dani Khalid John
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

1

110V DC SYSTEM

1. DC system consist of:

a. Battery
b. Battery charger
c. Loads

2. Battery Introduction

If two electrodes of different metals are immersed into a proper


solution or chemicals, a chemical reaction will occur such that there
will be voltage (EMF) across the electrodes. Those arrangements are
called cell. Batteries are combination of two or more cells.

3. Types of Batteries

a. Alkaline/Nickel cadmium battery


Positive electrodes – Nickel Oxides + Cadmium Oxides

b. Negative electrodes – Nickel – Iron


c. Electrolytes – Potassium Hydroxides in distilled water

4. Charging & Discharging

When the cells are connected to loads, current will flow from negative
electrodes to positive via the load connections. This is called
discharging. This flow of current causes all the properties of the
electrolyte and the electrodes to change and this reduces the
capabilities of the cell to provide voltage.

To normalize the reduction and its properties an external DC current


(charger) is introduced to the electrodes. This is called charging.

5. Specific Gravity

5.1 is a method of measuring its contents or density of solution in


water (S.G for water = 1).
5.2 Measurement of specific gravity is done using hydrometer
5.3 S.G for acid battery = 1.25 to 1.28
2

S.G for alkaline battery > 1.120

Note; hydrometer used for acid not to be used for alkaline

6. Terminal Voltage

6.1 The output voltage for individual cells


6.2 Values varies depending on manufacturer and setting but in
sub-station normally:

Acid batteries - 2.2 to 2.25 volt


Alkaline batteries - 1.4 to 1.5 volt

7. Battery Ratings

7.1 Usually battery rating is rated at Ampere-Hours

8. Battery charger

8.1 To inject DC current to battery to charge battery


8.2 Consists mainly of a rectifier that converts AC to DC
8.3 It can be single phase or three phase input rectifier. The
three phase rectifier is superior and more stable (low ripple)
8.4 Battery charger is rated at the maximum current output it
can produce

9. Charging Facilities of A Battery Charger

9.1 Float charger

A system where the rectifier + battery + load connected


together to maintain the DC voltage and at the same time
charge the battery.

9.2 Boost charge

Charging batteries to higher voltage and current. This is usually


done when:

a. Commissioning
3

b. AC failure
c. Adding electrolytes

10.Meters on Battery Charger

Meters on battery charger varies depending on charger design but all


chargers should have the following:

a. AC input
b. DC volt
c. Battery ammeter
d. Charger ammeter
e. Load ammeter
f. Electrolyte (warning/alarm)

You might also like