Scribd
Upload
419 views

Keypad IEI Programing

This document provides instructions for programming a keypad access control system. It outlines 20 different programming options including changing the master code, adding/editing user codes, setting relay times for different outputs, and configuring additional settings like keypress feedback and auto entry modes. Each programming step involves entering a unique code combination followed by the desired programming input and confirmation to save the changes.

Uploaded by

GUILLERMO ENRIQUE MORALES MENDOZA
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
419 views

Keypad IEI Programing

This document provides instructions for programming a keypad access control system. It outlines 20 different programming options including changing the master code, adding/editing user codes, setting relay times for different outputs, and configuring additional settings like keypress feedback and auto entry modes. Each programming step involves entering a unique code combination followed by the desired programming input and confirmation to save the changes.

Uploaded by

GUILLERMO ENRIQUE MORALES MENDOZA
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Keypad IEI programing

PROGRAMMING 
Press 99 # (master code )
1. Enter programming mode Yellow LED 1
* Flashes slowly 

2. To change master code   2

Press 1 # (new master code)


* Flashes fast
Repeat (new master code)
* Flashes slowly 

If main relay time must be changed, substitute option 2 from PROGRAMMING OPTIONS CHART for
step above. 3. To add/change second code 
Press 2 # (new user code)
* Flashes fast Repeat (new user code) * Flashes slowly 

4. To add/change third code 


Press 3 # (new user code)
* Flashes fast
Repeat (new user code)
* Flashes slowly 

5. Up to 120 codes may be added in this fashion 

6. Exit programming mode 


Press
* Out 

A user code is stored in it’s own user location.  


There are 120 user locations available. 

• Some Door•Gard products contain a sounder in place of the yellow LED. In these products
1

the flashing is replaced by a beeping. 


• The master code is always in user location 1. • The master code allows access to the 
2

programming mode & activates the main relay. • All codes must be followed by the * key. 
• Codes may be from 1-6 digits in length, and digits may be repeated. 
• If the master code is forgotten or does not seem to be working, momentarily push SW1 on the
circuit board, (see wiring diagram for location) to enter pro gramming mode and follow step
two from above to program a new master code. 
• If the yellow LED lights (or sounder sounds) solid while in programming mode an error has occurred. Press * to clear
(yellow LED should flash or sounder sound) and start over from step 2 or 3 above.

PROGRAMMING OPTIONS CHART 


If the pre-programmed default values must be changed 
or additional functions are desired, the following options may be programmed. 
1. Enter programming mode Press 99 # (master code)
* 
2. Change master code/set main relay time 1 (SEE BELOW) Press (Relay Time) # 1 # (new code) (repeat code)
* * Example: Master
code of 4321/relay time of 10 seconds Press 10 # 1 # 4321 * 4321 * 

3. Add/change user code Press (user location) # (new code) (repeat code)
* * 
4. Add/change user code with a different output Press (Relay Time) # (user location) # (new code)
* time on main relay 1 (SEE BELOW) (repeat
code)
* 
5. Delete user codes Press (user location) #
* * 
Press 12 # (Relay Time) # 0 #
6. Set output 2 time 1 (SEE BELOW)
* * 7. Set output 3 time 1 (SEE

Press 13 # (Relay Time) # 0 # Press 14 # (Relay Time) # 0 #


BELOW)
* * 8. Set output 4 time 1 (SEE BELOW)
* * 
9. Set outputs for Remote Triggering Input Press 17 # (outputs: .ie. 1, 2 or 2, 3 etc.) # 0 #
* * Note: 0= no outputs 
Press 18 # (outputs: i.e. 1, 2 or 2, 3 etc.) # 0 #
10. Set outputs for Panic 2 (SEE BELOW)
* * Note 0= no outputs 
11. Turn keypress feedback/audible keypress on Press 30 # 0 # 1 #
* * 
12. Turn keypress feedback/audible keypress off Press 30 # 0 # 0 #
* * 
13. Turn yellow LED/sounder on with relay Press 30 # 1 # 1 #
* * 
14. Turn yellow LED/sounder off with relay Press 30 # 1 # 0 #
* * 
15. Turn auto entry on Press 30 # 2 # 1 #
* * 
16. Turn auto entry off Press 30 # 2 # 0 #
* * 
17. Turn keypad active output on 3 (SEE BELOW) Press 43 # 0 # 99 #
* * 
18. Turn keypad active off Press 43 # 0 # 00 #
* * 
19. Erase keypad memory/reset defaults Press 46 # 00000 # 00000 #
* * 
code Press 59 # (outputs: i.e. 1, 2 or 2, 3 etc.) # (user location) # (new code) * (repeat
4

code) * 
Example: User 2; code of 4321*; energize outputs 2 & 3 Press 59 # 23 # 02# 4321 * 4321 *

You might also like