Operation Manual Volume II – MPLS

Quidway S8500 Series Routing Switches Table of Contents

Table of Contents

Chapter 1 MPLS Architecture....................................................................................................... 1-1

1.1 MPLS Overview ................................................................................................................. 1-1
1.2 MPLS Basic Concepts ....................................................................................................... 1-1
1.2.1 FEC ......................................................................................................................... 1-1
1.2.2 Label........................................................................................................................ 1-2
1.2.3 LDP ......................................................................................................................... 1-4
1.3 MPLS Architecture ............................................................................................................. 1-4
1.3.1 MPLS Network Structure......................................................................................... 1-4
1.3.2 Forwarding Labeled Packets................................................................................... 1-5
1.3.3 Establishing LSP ..................................................................................................... 1-6
1.3.4 LSP Tunnel and Hierarchy ...................................................................................... 1-7
1.3.5 MPLS and Other Protocols (Routing Protocols) ..................................................... 1-8
1.3.6 MPLS Application (MPLS-based VPN) ................................................................... 1-8

Chapter 2 MPLS Basic Capability Configuration ....................................................................... 2-1

2.1 MPLS Basic Capability Overview ...................................................................................... 2-1
2.2 MPLS Configuration........................................................................................................... 2-1
2.2.1 Defining MPLS LSR ID............................................................................................ 2-1
2.2.2 Enabling MPLS and Entering MPLS View .............................................................. 2-2
2.2.3 Configuring the Topology-Driven LSP Setup Policy ............................................... 2-2
2.2.4 Configuring Static LSP ............................................................................................ 2-3
2.3 LDP Configuration.............................................................................................................. 2-3
2.3.1 Enabling LDP protocol ............................................................................................ 2-4
2.3.2 Enabling LDP on VLAN interface ............................................................................ 2-4
2.3.3 Configuring Remote-Peer for Extended Discovery Mode....................................... 2-4
2.3.4 Configuring session parameters ............................................................................. 2-5
2.3.5 Configuring LDP Loop Detection Control................................................................ 2-7
2.3.6 Configuring LDP Authentication Mode Between Every Two Routers ..................... 2-8
2.4 Displaying and Debugging MPLS Basic Capability ........................................................... 2-9
2.4.1 Displaying and Debugging MPLS ........................................................................... 2-9
2.4.2 Displaying and Debugging LDP ............................................................................ 2-11
2.5 Typical MPLS Configuration Example ............................................................................. 2-12
2.6 Troubleshooting MPLS Configuration.............................................................................. 2-15

Chapter 3 BGP/MPLS VPN Configuration ................................................................................... 3-1

3.1 BGP/MPLS VPN Overview ................................................................................................ 3-1
3.1.1 BGP/MPLS VPN Model........................................................................................... 3-2
3.1.2 BGP/MPLS VPN Implementation............................................................................ 3-5
3.1.3 Nested BGP/MPLS VPN Implementation ............................................................... 3-7

Huawei Technologies Proprietary

i
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Table of Contents

3.1.4 Hierarchical BGP/MPLS VPN Implementation........................................................ 3-7

3.1.5 Introduction to OSPF Multi-instance ....................................................................... 3-8
3.1.6 Introduction to Multi-Role Host................................................................................ 3-9
3.2 BGP/MPLS VPN Configuration........................................................................................ 3-10
3.2.1 3.2.1 Configuring Various Kinds of Routers ..................................................... 3-10
3.2.2 Configuring CE Router .......................................................................................... 3-11
3.2.3 Configuring PE Router .......................................................................................... 3-12
3.2.4 Configuring P Router............................................................................................. 3-24
3.3 Displaying and Debugging BGP/MPLS VPN................................................................... 3-25
3.4 Typical BGP/MPLS VPN Configuration Example ............................................................ 3-27
3.4.1 Integrated BGP/MPLS VPN Configuration Example............................................. 3-27
3.4.2 Extranet Configuration Example ........................................................................... 3-33
3.4.3 Hub&Spoke Configuration Example ..................................................................... 3-38
3.4.4 CE Dual-home Configuration Example ................................................................. 3-44
3.4.5 Cross-domain BGP/MPLS VPN Configuration Example ...................................... 3-50
3.4.6 Cross-Domain BGP/MPLS VPN Configuration Example — Option C.................. 3-55
3.4.7 Hierarchical BGP/MPLS VPN Configuration Example.......................................... 3-62
3.4.8 OSPF Multi-instance Sham-link Configuration Example....................................... 3-65
3.4.9 Nested BGP/MPLS VPN Configuration Example ................................................. 3-71
3.4.10 OSPF Multi-instance CE Configuration Example................................................ 3-77
3.4.11 Multi-Role Host Configuration Example .............................................................. 3-79
3.5 Troubleshooting ............................................................................................................... 3-84

Chapter 4 MPLS L2VPN ................................................................................................................ 4-1

4.1 MPLS L2VP Overview ....................................................................................................... 4-1
4.1.1 Introduction to MPLS L2VP..................................................................................... 4-1
4.1.2 Packet Forwarding .................................................................................................. 4-2
4.1.3 Implementation........................................................................................................ 4-3
4.2 CCC MPLS L2VPN Configuration ..................................................................................... 4-5
4.2.1 Configuring CCC MPLS L2VPN.............................................................................. 4-5
4.2.2 CCC MPLS L2VPN Configuration Example............................................................ 4-6
4.3 Martini MPLS L2VPN Configuration ................................................................................ 4-10
4.3.1 Configuring Martini MPLS L2VPN......................................................................... 4-10
4.3.2 Martini MPLS L2VPN Configuration Example....................................................... 4-11
4.4 Kompella MPLS L2VPN Configuration ............................................................................ 4-15
4.4.1 Configuring Kompella MPLS L2VPN..................................................................... 4-15
4.4.2 Kompella MPLS L2VPN Configuration Example .................................................. 4-17
4.5 Displaying and Debugging MPLS L2VPN ....................................................................... 4-21
4.6 Troubleshooting MPLS L2VPN........................................................................................ 4-22

Chapter 5 Card Intermixing for MPLS Support .......................................................................... 5-1

5.1 Overview ............................................................................................................................ 5-1
5.1.1 Introduction to Card Intermixing .............................................................................. 5-1
5.1.2 Card Intermixing Mechanism .................................................................................. 5-1

Huawei Technologies Proprietary

ii
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Table of Contents

5.2 Restrictions in Intermixing Networking............................................................................... 5-2

5.2.1 Rules of Intermixing Configuration .......................................................................... 5-2
5.2.2 Restrictions in Card Intermixing .............................................................................. 5-3
5.3 5.3 Introduction to intermixing configuration task .............................................................. 5-4
5.3.2 Configuring Routing Protocols ................................................................................ 5-4
5.3.3 Configuring Basic Capability of MPLS .................................................................... 5-4
5.3.4 Configuring MPLS VPN........................................................................................... 5-4
5.3.5 Configuring flow template and ACL rules................................................................ 5-4
5.3.6 Applying Flow Template and Redirection in Port Mode .......................................... 5-6
5.3.7 Typical Networking Example................................................................................... 5-7
5.4 Restrictions in Networking of Various MPLS Cards ........................................................ 5-13
5.4.1 Exclusively non-MPLS Cards................................................................................ 5-14
5.4.2 Exclusively MPLS Cards ....................................................................................... 5-14
5.4.3 Exclusively VPLS Service Cards........................................................................... 5-14
5.4.4 Combination of One MPLS Card and Multiple non-MPLS Cards ......................... 5-14
5.4.5 Combination of Multiple MPLS cards and Multiple non-MPLS Cards................... 5-15
5.4.6 Combination of One VPLS Card and Multiple non-MPLS Cards.......................... 5-15
5.4.7 Combination of One VPLS card and Multiple MPLS Cards.................................. 5-15
5.4.8 Combination of One VPLS card, One MPLS Card and Multiple non-MPLS Cards
........................................................................................................................................ 5-15

Huawei Technologies Proprietary

iii
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

Chapter 1 MPLS Architecture

Note:
The Quidway S8500 Series Routing Switches (hereinafter referred to as S8500 series)
running MPLS can serve as routers. Routers mentioned in this manual can be either a
router in common sense, or a layer 3 Ethernet switch running MPLS.
For S8500 switches, only the interface boards with the suffixes C, CA and CB and
VPLS service processor cards support the MPLS function. To enable MPLS function on
the S8500 switches, you must select the interface cards that support MPLS or VPLS
service processor cards. The suffix of a board can be identified through the silkscreen
on the upper right corner of the front panel of the card. For example, the silkscreen on
LSB1GP12B0 card is GP12B, so the suffix of the card is B.

1.1 MPLS Overview

MPLS (Multiprotocol Label Switching) encapsulates network layer packets with short
and fixed-length labels. As the name implies, it supports multiple protocols, such as IP,
IPv6, and IPX. And it allows a device to make forwarding decision based on the labels
attached to the received packets without going through the complex routing table
lookup procedures with IP. MPLS brings together the advantages of the connectionless
control with IP and the connection-oriented forwarding with ATM. In addition to the
support from IP routing and control protocols, its powerful and flexible routing functions
allows it to accommodate to various emerging applications.
MPLS was initially proposed to accelerate the packet forwarding on routers, but it has
been widely used in Traffic Engineering (TE), Virtual Private Network (VPN), and other
aspects, and is becoming one of the most important standards on large scale IP
networks.

1.2 MPLS Basic Concepts

1.2.1 FEC

Forwarding Equivalence Class (FEC) is an important concept in MPLS. MPLS is

actually a kind of classify-and-forward technology. It categorizes packets with the same
forwarding strategy (same destination addresses, same forwarding routes and same
QoS levels) into one class, which is called a FEC. Generally, the FEC classification is

Huawei Technologies Proprietary

1-1
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

based on network layer address. Packets of the same FEC are processed in the same
way in MPLS network.

1.2.2 Label

I. Label definition

A label is a locally significant short identifier with fixed length, which is used to identify a
FEC. When reaching at MPLS network ingress, packets are divided into different FECs,
based on their FECs, different labels are encapsulated into the packets. Later
forwarding is based on these labels.

II. Label structure

The structure of the label is shown in Figure 1-1.

Label Exp S TTL

Figure 1-1 Label structure

Label is located between the link layer header and the network layer packet, with the
length of four bytes. A label contains four fields:
Label: label value, 20 bits.
Exp: three bits, reserved, used for COS.
S: one bit, MPLS supports hierarchical label structure, namely multi-layer label. Value 1
refers to the label of bottom layer.
TTL: eight bits, with the same meaning as TTL in IP packet.

III. Label operations

1) Label mapping
There are two types of label mapping: label mapping at ingress routers, and label
mapping in MPLS domain.
The first type of mapping is implemented at Ingress label switching routers (LSR). The
Ingress LSRs group the incoming packets into multiple FECs based on certain
principles, and then map corresponding labels to these FECs and record the mapping
results into the label information base (LIB). In simple words, label mapping is to assign
a label to a FEC.
The second type is also called incoming label mapping (ILM), that is, to map each input
label to a series of next hop label forwarding entries (NHLFE). The packets are
forwarded along the paths based on the mapping results.
2) Label encapsulation
Figure 1-2 illustrates label encapsulation in different media:

Huawei Technologies Proprietary

1-2
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

Ethernet
/SONET
以太网报头/
packet
Ethernet /PPP
PPP
header/ 报头
PPP header flag Layer 3 data
/ SDH 以太网报头 报头 标签 三层数据

Frame mode
ATM packet ATM报头
ATM header
报头 标签
flag 三层数据
Layer 3 data

Cell mode
ATM packet VPE/VCI
VPI/VCI
标签
flag 三层数据
Layer 3 data

Figure 1-2 Label position in packet

In Ethernet packets and PPP packets, label stack lies between layer 2 header and layer
3 data, acting like a shim. In ATM cell mode packets, VPI/VCI is used as the label.
3) Label assignment and distribution
Label distribution refers to the process of creating a corresponding label switching path
(LSP) for a FEC.
In the MPLS architecture, the decision to bind a particular label to a particular FEC is
made by downstream LSR; after making the decision, the downstream LSR notifies the
upstream LSR. That is to say, the label is assigned by the downstream LSR, and the
assigned label is distributed from downstream to upstream.
Two label distribution modes are available in MPLS: downstream unsolicited (DU)
mode and downstream on demand (DoD) mode.
z For a specific FEC, if LSR originates label assignment and distribution even
without receiving label request message from upstream, it is in DU mode.
z For a specific FEC, if LSR begins label assignment and distribution only after
receiving label request message from upstream, it is in DoD mode.
The upstream and downstream which have adjacency relation in-label distribution
should reach agreement on label distribution mode.
To distribute labels to its peer, the LSR can use Label Distribution Protocol (LDP)
messages or make the labels carried on other routing protocol messages.

Note:
Upstream and downstream are just on a relative basis: For a packet forwarding process,
the transmit router serves as upstream LSR and receive router serves as downstream
LSR. Currently, the S8500 series adopt the DU label distribution mode.

4) Label assignment control mode

There are two modes to control the assignment and distribution of labels: independent
mode and ordered mode.

Huawei Technologies Proprietary

1-3
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

In independent control mode, each LSR can send label mapping messages to the
LSRs it connects to at anytime.
In ordered control mode, a LSR can send label mapping messages to upstream only
when it receives a specific label mapping messages of the next hop of a FEC or the
LSR serves as LSP (Label Switching Path) egress node.

Note:
Currently, the S8500 series adopt the ordered label control mode.

5) Label retention mode

There are two label-retention modes: liberal label retention mode and conservative
label retention mode.
Suppose there are two LSRs: Ru and Rd. For a specific FEC, if LSR Ru has received
the label binding from LSR Rd, in case Rd is not the next hop of Ru and Ru saves this
binding, then it is the liberal label retention. And if Ru discards this binding, then it is the
conservative label retention mode.
In case it is required that LSR is capable of adapting route variation rapidly, you can use
the liberal label retention mode. In case it is required that a few labels are saved in LSR,
you can use the conservative label retention mode.

Note:
Currently, the S8500 series adopt the liberal label retention mode.

1.2.3 LDP

Label distribution protocol (LDP) is the signaling control protocol in MPLS, which
controls binding labels and FECs between LSRs and coordinates a series of
procedures between LSRs.

1.3 MPLS Architecture

1.3.1 MPLS Network Structure

The basic composing unit of MPLS network is LSR (Label Switching Router). It runs
MPLS control protocol and L3 routing protocol, exchanges routing messages with other
LSRs and create the routing table, maps FECs with IP packet headers, binds FECs

Huawei Technologies Proprietary

1-4
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

with labels, distributes label binding messages, establishes and maintains label
forwarding table.
The network consisting of LSRs is called MPLS domain. The LSR that is located at the
edge of the domain is called edge LSR (LER, Labeled Edge Router). It connects an
MPLS domain with a non-MPLS domain or with another MPLS domain, classifies
packets, distributes labels (as ingress LER) and distracts labels (as egress LER). The
ingress LER is termed as ingress and egress LER as egress.
The LSR that is located inside the domain is called core LSR, which provides functions
such as label swapping and label distribution. The labeled packets are transmitted
along the LSP (Label Switched Path) composed of a series of LSRs.

LSP
Ingress

Egress

MPLS core router (LSR)

MPLS edge router (LER)

Figure 1-3 MPLS basic principle

1.3.2 Forwarding Labeled Packets

At the ingress, the packets entering the network are classified into FECs according to
their characteristics. Usually, packets are classified into FECs according to the IP
address prefix or host address. Packets in the same FEC pass through the same path
(that is, LSP) in MPLS area. LSR assigns a short label of fixed length for the incoming
FEC packet, and then forwards it through the corresponding interface.
On the LSR along the LSP, the mapping table of the import/export labels has been
established (the element of this table is referred to as Next Hop Label Forwarding Entry
(NHLFE)). When the labeled packet arrives, LSR only needs to find the corresponding
NHLFE from the table according to the label and replace the original label with a new
one, and then forwards the labeled packet. This process is called Incoming Label Map
(ILM).
At the ingress, MPLS specifies a FEC for a specific packet, and the following routers
only need to forward the packet by label switching, therefore this method is much
simpler than general network layer forwarding and increases the forwarding speed.

Huawei Technologies Proprietary

1-5
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

1.3.3 Establishing LSP

Actually, the establishment of LSP refers to the process of binding FEC with the label,
and then advertising this binding to the adjacent LSR on LSP. This process is
implemented through LDP, which regulates the message in interactive processing and
message structure between LSRs as well as routing mode.

I. LDP working process

Through sending Hello message periodically, an LSR finds its neighbor and then
establish LDP session with the newly discovered adjacent LSR. By LDP session, the
adjacent LSRs advertise such information as label switching mode, label space,
session Keepalive timer value to each other. LDP session is a TCP connection, which
needs to be maintained through LDP message. In case there is not any other LDP
message during the time period specified by the session Keepalive timer value, and
then it is necessary to send session Keepalive message to maintain the existence of
LDP session. Figure 1-4 illustrates the diagram of LDP label distribution.
LSP1

Ingress
A B
C
LSP2
Egress
Label request message D
E

Label map message

F G
MPLS core router (LSR)

MPLS edge router (LER)

LDP session H

Figure 1-4 Label distribution process

For the label distribution mentioned previously, there are two modes: DoD and DU. The
main difference between these two modes is that the label mapping messages are
distributed actively or passively.
In DoD mode, the label is distributed in this way: the upstream LSR sends label request
message (containing FEC descriptive information) to the downstream LSR, and the
downstream LSR distributes label for this FEC, and then it sends the bound label back
to the upstream LSR through label map message. The time when the downstream LSR
feeds back the label map message depends on whether this LSR uses independent
label control mode or sequential label control mode. When the sequential label control
mode is used by the downstream LSR, the label map message is sent back to its
upstream LSR if only it has received the label map message from its downstream LSR.
And when the independent label control mode is used by the downstream LSR, then it
will send label map message to its upstream LSR immediately, no matter whether it has

Huawei Technologies Proprietary

1-6
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

received the returned label map message from its downstream LSR. Usually, the
upstream LSR selects the downstream LSR according to the information in its routing
table. In Figure 1-4, LSRs on the way along LSP1 use the sequential label control mode,
and the LSR F on LSP2 uses independent label control mode.
In DU mode, the label is distributed in the following way: when LDP session is
established successfully, the downstream LSR will actively distribute label map
message to its upstream LSR. And the upstream LSR saves the label map information
and processes the received label map information according to the routing table.

II. LSP loop control

While establishing LSP in MPLS domain, it is also necessary to prevent the presence of
path loop. Then, such two methods as maximum hop count and path vector can be
used.
The maximum hop count method refers to that the hop-count information is contained
in the message bound with the forwarding label, and the value pluses one for each hop.
When the value exceeds the threshold value, it is considered that a loop presents, and
the process for establishing LSP is terminated.
The path vector method refers to that the path information is recorded in the message
bound with the forwarding label, and, for every hop, the corresponding router checks if
its ID is contained in this record. If not, the router adds its ID into the record; and if yes,
it indicates that a loop presents and the process for establishing LSP is terminated.

1.3.4 LSP Tunnel and Hierarchy

I. LSP tunnel

MPLS supports LSP tunnel technology. On an LSP path, LSR Ru and LSR Rd are both
the upstream and the downstream for each other. However, the path between LSR Ru
and LSR Rd may not be part of the path provided by routing protocol. MPLS allows
establishing a new LSP path <Ru R1...Rn Rd> between LSR Ru and LSR Rd, and LSR
Ru and LSR Rd are respectively the starting point and ending point of this LSP. The
LSP between LSR Ru and LSR Rd is referred to as the LSP tunnel, which avoids the
traditional encapsulated tunnel on the network layer. If the route along which the tunnel
passes and the route obtained hop by hop from routing protocol is consistent, this
tunnel is called hop-by-hop routing tunnel. And if the two routes are not consistent, then
the tunnel of this type is called explicit routing tunnel.

R1 R2 R3 R4 Layer 1

R21 R22 Layer 2

Figure 1-5 LSP tunnel

Huawei Technologies Proprietary

1-7
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

As shown in Figure 1-5, LSP <R2 R21 R22 R3> is a tunnel between R2 and R3.

II. Multi-layer label stack

In MPLS, a packet may carry multiple labels which are in the form of stack. Operations
to the stack follow the “last in first out” principle and it is always the labels at the top of
the stack that decide how to forward packets. Pushing label indicates to add a label into
a outgoing packet, then the depth of the label stack is the former one plus 1, and the
current label of the packet changes to the newly added one; popping a label indicates to
remove a label form a packet, then the depth of the packet is the former one minus 1,
and the current label of the packet changes to the label of its underlayer.
Multiple-layer label stack is used in LSP tunnel. When a packet travels in LSP tunnel,
there will be multiple layers for the label of the packet. Then, at the ingress and egress
of each tunnel, it is necessary to implement pushing and popping operation for the label
stack. For each pushing operation, the label will be added with one layer. And there is
no depth limitation for the label stack from MPLS.
The labels are organized according to the principle of “last in first out” in the label stack,
and MPLS processes the labels beginning from the top of the stack.
If the depth of the label stack for a packet is m, it indicates that the label at the bottom of
that stack is level 1 label, and the label at the top of the stack is level m label. A packet
with no label can be regarded as a packet with empty label stack, that is, the depth of its
label stack is 0.

1.3.5 MPLS and Other Protocols (Routing Protocols)

When LDP establishes LSP in hop-by-hop mode, the next hop is determined by using
the information, which is usually collected by such routing protocols as IGP, BGP in
each LSR route forwarding table, on the way. However, LDP just uses the routing
information indirectly, rather than associates with various routing protocols directly.
On the other hand, although LDP is the special protocol for implementing label
distribution, it is not the sole protocol for label distribution. The existing protocols such
as BGP, RSVP, after being extended, can also support MPLS label distribution. For
some MPLS applications, it is also necessary to extend some routing protocols. For
example, the application of MPLS VPN requires extending the BGP protocol, thus the
BGP protocol can propagate VPN routing information.

1.3.6 MPLS Application (MPLS-based VPN)

To transmit data stream of private network on public network, traditional VPN uses
tunnel protocols like GRE, L2TP, and PPTP. LSP itself is a tunnel on public network, so
there are obvious advantages to implement VPN by MPLS. MPLS VPN connects the
geographically different branches of private network by using LSP, forming a united
network. MPLS VPN also supports the interconnection between different VPNs.

Huawei Technologies Proprietary

1-8
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 1 MPLS Architecture

CE3
Private
network branch 3
PE3

CE2
CE1 PE1
Private Private
Backbone network
network branch 1 network branch 2

PE2

Figure 1-6 MPLS-Based VPN

The basic structure of MPLS-based VPN is shown in Figure 1-6. CE is the customer
edge device, and it may either be a router or a switch, or perhaps a host. PE is a service
provider edge router, which is located on the backbone network. PE is responsible for
the management of VPN customers, establishing LSP connection between various
PEs, route allocation among different branches of the same VPN customer.
Usually the route allocation between PEs is implemented by using extended BGP.
MPLS VPN supports the IP address multiplexing between different branches and the
interconnection between different VPNs. Compared with traditional route, it is
necessary to add branch and VPN identifier information in VPN route. So, it is
necessary to extend BGP so as to carry VPN routing information.

Huawei Technologies Proprietary

1-9
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Chapter 2 MPLS Basic Capability Configuration

2.1 MPLS Basic Capability Overview

Basic MPLS forwarding functions includes LDP session establishment and LSP path
maintenance.
The typical configuration procedure for enabling basic MPLS functions on a routing
switch is as follows:
1) Configure LSR ID
2) Enable MPLS
3) Enable LDP
4) Enter VLAN interface view and enable MPLS and LDP on the interface
Then the routing switch can provide MPLS forwarding and LDP signaling functions.
If you want to modify the default parameters or enable some special functions, for
example, manually creating LSP or explicit route, you can configure according to the
methods in configuration list. For some complicated functions, configuration
combination may be required.

2.2 MPLS Configuration

The following sections describe the required configuration tasks for MPLS basic
capability:
z Defining MPLS LSR ID
z Enabling MPLS and Entering MPLS View
The following sections describe the optional configuration tasks for MPLS basic
capability:
z Configuring the Topology-Driven LSP Setup Policy
z Configuring Static LSP

2.2.1 Defining MPLS LSR ID

Before configuring any other MPLS command, it is necessary to configure LSR ID firstly.
This ID is usually in IP address format and must be unique in the domain.
Perform the following configuration in the system view.

Huawei Technologies Proprietary

2-1
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Table 2-1 Define MPLS LSR ID

Operation Command
Define LSR ID mpls lsr-id ip-address
Delete LSR ID undo mpls lsr-id

By default, LSR ID is not defined.

2.2.2 Enabling MPLS and Entering MPLS View

In system view, you can first enable MPLS globally and enter MPLS view using the
mpls command. Then you can directly enter MPLS view after using the mpls
command in system view.
Use the mpls command in VLAN interface view to enable MPLS on the VLAN
interface.

Table 2-2 Enter MPLS view

Operation Command
Enable MPLS globally and enter MPLS view (system view)
mpls
Enable MPLS on a VLAN interface (VLAN interface view)
Disable MPLS globally or on a VLAN interface (system or VLAN
undo mpls
interface view)

By default, MPLS is not enabled.

2.2.3 Configuring the Topology-Driven LSP Setup Policy

It refers to specifying filtering policy as all or ip-prefix.

Perform the following configuration in MPLS view.

Table 2-3 Configure the topology-driven LSP setup policy

Operation Command
Configure the topology-Driven LSP
lsp-trigger { all | ip-prefix ip-prefix }
setup policy
Use the default value, which only allows undo lsp-trigger { all | ip-prefix
32-bit IP to trigger LSP. ip-prefix }

Huawei Technologies Proprietary

2-2
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

2.2.4 Configuring Static LSP

You can manually set an LSR to be a node along an LSP, and place a limit on the traffic
over the LSP. Depending on the position in an MPLS domain, an LSR along an LSP can
be the ingress node, an intermediate node (also called transit node), or the egress
node. Note that an LSP operates normally only after all the LSRs along the LSP have
been properly configured.
Perform the following configuration in MPLS view.

Table 2-4 Set the local LSR to a node on a specified LSP

Operation Command
static-lsp ingress lsp-name { destination
Set the current LSR to the
dest-addr { addr-mask | mask-length } | l2vpn }
ingress node of the specified
nexthop next-hop-addr } } out-label
LSP
out-label-value
Cancel the ingress node
undo static-lsp ingress lsp-name
setting of the specified LSP
static-lsp transit lsp-name [ l2vpn ]
Set the current LSR to an
incoming-interface interface-type
intermediate node along the
interface-number in-label in-label-value nexthop
specified LSP
next-hop-addr out-label out-label-value
Cancel the intermediate node
undo static-lsp transit lsp-name
setting of the specified LSP
Set the current LSR to the static-lsp egress lsp-name [ l2vpn ]
egress node of the specified incoming-interface interface-type
LSP interface-number in-label in-label-value
Cancel the egress node
undo static-lsp egress lsp-name
setting of the specified LSP

2.3 LDP Configuration

The following sections describe the required LDP configuration tasks for MPLS basic
capability:
z Enabling LDP protocol
z Enabling LDP on VLAN interface
The following sections describe the optional LDP configuration tasks for MPLS basic
capability:
z Configuring Remote-Peer for Extended Discovery Mode
z Configuring session parameters

Huawei Technologies Proprietary

2-3
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

2.3.1 Enabling LDP protocol

To configure LDP, first enable LDP.

Perform the following configuration in the system view.

Table 2-5 Enable/disable LDP view

Operation Command
Enable LDP protocol mpls ldp
Disable LDP undo mpls ldp

By default, LDP is disabled.

2.3.2 Enabling LDP on VLAN interface

To make the VLAN interface support LDP, you must enable LDP function on the
interface in VLAN interface mode. After enabling the LDP function, the interface then
sets up session. It begins to set up LSP if in topology-driven mode,.
Disabling LDP function on interface causes the break of all LDP session in VLAN
interface, and all the LSP based on those sessions are deleted. So you must use this
command with cautiously.
Perform the following configuration in the interface view.

Table 2-6 Enable/disable LDP on interface

Operation Command
Enable LDP function on interface mpls ldp enable
Disable LDP function on interface mpls ldp disable

By default, the interface LDP function is disabled.

2.3.3 Configuring Remote-Peer for Extended Discovery Mode

The Remote-peer configuration is mainly used for extended discovery mode so that
this LSR can establish sessions with LSRs that are not directly connected with it at the
link layer.

I. Enter Remote-peer view

Perform the following configuration in the system view.

Huawei Technologies Proprietary

2-4
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Table 2-7 Enter Remote-peer view

Operation Command
Enter Remote-peer view mpls ldp remote-peer index
Delete the corresponding Remote-peer undo mpls ldp remote-peer index

There is no default remote-peer.

II. Configuring an address for the Remote-peer

You can specify the address of any LDP-enabled interface on the Remote-peer or the
address of the Loopback interface on the LSR that has advertised the route as the
address of the Remote-peer.
Perform the following configuration in the Remote-peer view.

Table 2-8 Configure a Remote-peer address

Operation Command
Configure a remote-peer address remote-ip remoteip

remoteip: the IP address of the Remote-peer. It should be the ID of the peer LSR.

2.3.4 Configuring session parameters

I. Configuring session hold-time

The LDP entity on the interface sends Hello packets periodically to find out LDP peer,
and the established sessions must also maintain their existence by periodic message
(if there is no LDP message, then Keepalive message must be sent).

Note:
There are two types of LDP sessions: Basic and Remote. Basic session can be
established only on two direct-connect switches, while Remote session can be on two
switches which are not directly connected. You can only configure Basic sessions in
VLAN interface view and Remote sessions in remote-peer view.

Huawei Technologies Proprietary

2-5
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Caution:

Modifying the holdtime parameter results in re-establish the original session, as well as
the LSP over this session. Here the session refers to Basic session, but not Remote
session.

Configure Basic session hold-time in VLAN interface view.

Table 2-9 Configure Basic session hold-time

Operation Command
mpls ldp timer { session-hold
Configure session hold-time
session-holdtime | hello hello-holdtime }
Return to the default value undo mpls ldp timer { session-hold | hello }

By default, the session-holdtime is 60 seconds and hello-holdtime is 15 seconds.

Configure Remote session hold-time in Remote-peer view.

Table 2-10 Configure Remote session hold-time

Operation Command
mpls ldp timer { targeted-session-hold |
Configure session hold-time
targeted-hello } {holdtime | interval } }

undo mpls ldp timer

Return to the default value
{ targeted-session-hold | targeted-hello }

By default, targeted-session-hold holdtime is 60 seconds, and the interval is 24

seconds; targeted-hello holdtime is 45 seconds and the interval is 13 seconds.

II. Configuring Hello transport-address

The transport-address discussed here refers to the address carried in the transport
address TLV in Hello messages. Generally, you can configure the transport-address to
the MPLS LSR ID of the current LSR, but you can also configure the transport-address
to other address flexibly as required by some applications.
Perform the following configuration in VLAN interface view.

Huawei Technologies Proprietary

2-6
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Table 2-11 Configure Hello transport-address

Operation Command
mpls ldp transport-ip { interface |
Configure Hello transport-address
ip-address }
Return to the default Hello
undo mpls ldp transport-ip
transport-address

Transport-address defaults to the MPLS LSR ID of the current LSR.

If there are multiple links connecting two neighboring LSRs, all the LDP-enabled
interfaces on the links connecting LSR and its neighbor must have the same transport
address. You are recommended to use the same interface address for all of them, that
is, LSR-ID.

2.3.5 Configuring LDP Loop Detection Control

I. Enabling loop detection

You can enable or disable the loop detection function during LDP signaling process.
The loop detection includes maximum hop count mode and path vector mode.
The maximum hop count method refers to that the hop-count information is contained
in the message bound with the forwarding label, and the value pluses one for each hop.
When the value exceeds the threshold value, it is considered that a loop presents, and
the process for establishing LSP is terminated.
The path vector method refers to that the path information is recorded in the message
bound with the forwarding label, and, for every hop, the corresponding router checks if
its ID is contained in this record. If not, the router adds its ID into the record; and if yes,
it indicates that a loop presents and the process for establishing LSP is terminated.
When this method is used, if the defined maximum value is exceeded, it is considered
that a loop happens and the LSP establishment fails.
Perform the following configuration in the system view.

Table 2-12 Enable loop detection

Operation Command
Enable loop detection mpls ldp loop-detect
Disable loop detection undo mpls ldp loop-detect

By default, the loop detection is disabled.

II. Setting the maximum hop count for loop detection

Huawei Technologies Proprietary

2-7
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

When maximum hop count mode is adopted for loop detection, the maximum
hop-count value can be defined. And if the maximum value is exceeded, it is
considered that a loop happens and the LSP establishment fails.
Perform the following configuration in the system view.

Table 2-13 Set the maximum hop count for loop detection

Operation Command
Set maximum hop count for loop detection mpls ldp hops-count hop-number
Return to the default maximum hop count undo mpls ldp hops-count

The maximum hop count of loop detection is 32 by default.

III. Setting the maximum hop count in path vector mode

When path vector mode is adopted for loop detection, it is also necessary to specify the
maximum value of LSP path. In this way, when one of the following conditions is met, it
is considered that a loop happens and the LSP establishment fails.
z The record of this LSR already exists in the path vector recording table.
z The path hop count exceeds this maximum value.
Perform the following configuration in the system view.

Table 2-14 Set the maximum hop count in path vector mode

Operation Command
Set the maximum hop count in path vector
mpls ldp path-vectors pv-number
mode
Return to the default maximum hop count in
undo mpls ldp path-vectors
path vector mode

The maximum of the maximum hop count of path vector is 32 by default.

2.3.6 Configuring LDP Authentication Mode Between Every Two Routers

Perform the following configuration in VLAN interface view or Remote-peer view.

Table 2-15 Configure LDP authentication mode (between every two routers)

Operation Command
mpls ldp password [ cipher | simple ]
Configure LDP authentication Mode
password
Remove LDP authentication undo mpls ldp password

Huawei Technologies Proprietary

2-8
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

2.4 Displaying and Debugging MPLS Basic Capability

2.4.1 Displaying and Debugging MPLS

I. Displaying static LSPs

After accomplishing the configuration tasks mentioned previously, you can execute the
display command in any view to view the running state of a single or all the static LSPs
and thus to evaluate the effect of the configurations.

Table 2-16 Display the static LSP information

Operation Command
display mpls static-lsp [ include text |
Display the static LSP information
verbose ]

II. Displaying the MPLS statistics information or LSP information of all ports or
a single VLAN interface

After finishing the configurations above, execute the display command in any view to
view the MPLS statistics information or LSP information of all ports or a single VLAN
interface. You can verify the effect of the configuration by checking the information on
display.

Table 2-17 Display statistics information of static LSP

Operation Command
Displaying the MPLS statistics display mpls statistics { interface
information or LSP information of all { Vlan-interface | all } | lsp { lsp-Index | all |
ports or a single VLAN interface lsp-name }

III. Displaying MPLS-enabled interfaces

After accomplishing the configuration tasks mentioned previously, you can execute the
display command in any view to view the information related to the MPLS-enabled
interfaces and thus to evaluate the effect of the configurations.

Table 2-18 Display information of the MPLS-enabled interfaces

Operation Command
Display information of the
display mpls interface
MPLS-enabled interfaces

Huawei Technologies Proprietary

2-9
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

IV. Displaying MPLS LSP information

Execute the following commands in any view to display the information related to MPLS
LSP.

Table 2-19 Display the information about MPLS LSP

Operation Command
Display the information about MPLS
display mpls lsp [ include text | verbose ]
LSP

V. Debugging MPLS

You may execute the debugging command in user view to debug the information
concerning all interfaces with MPLS function enabled.
As enabling debugging may affect the router performance, you are recommended to
use this command when necessary. Execute the undo form of this command to disable
the corresponding debugging.

Table 2-20 Enable/disable debugging for MPLS

Operation Command
Enable debugging for debugging mpls lspm { agent | all | event | ftn |
MPLS LSP interface | packet | policy process | vpn }
Disable debugging for undo debugging mpls lspm { agent | all | event | ftn |
MPLS LSP interface | packet | policy process | vpn }

VI. Trap information of MPLS

This command is used to enable the trap function of MPLS during an LSP/LDP setup
process.
Perform the following configuration in system view.

Table 2-21 Enable the trap function of MPLS

Operation Command
Enable the LDP Trap function of MPLS snmp-agent trap enable ldp
Disable the LDP Trap function of MPLS undo snmp-agent trap enable ldp
Enable the LSP Trap function of MPLS snmp-agent trap enable lsp
Disable the LSP Trap function of MPLS undo snmp-agent trap enable lsp

Huawei Technologies Proprietary

2-10
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

2.4.2 Displaying and Debugging LDP

I. LDP display commands

VRP provides abundant MPLS monitoring commands for monitoring states of LSRs,
LDP sessions, interfaces and peers. These commands are the powerful debugging and
diagnosing tools.
After accomplishing the configuration tasks described earlier, you can execute the
display command in any view to view the running state of LDP and thus to evaluate the
effect of the configurations.

Table 2-22 Display LDP

Operation Command
Display LDP information display mpls ldp
Display buffer information for LDP display mpls ldp buffer-info
Display LDP-enabled interface
display mpls ldp interface
information
Display LDP saved label information display mpls ldp lsp
Display information on all peers of LDP
display mpls ldp peer
session
Display information of the remote-peers
display mpls ldp remote
in the LDP sessions
Display states and parameters of LDP
display mpls ldp session
sessions

II. LDP debugging commands

Execute debugging command in user view for the debugging of various messages
related to LDP

Table 2-23 Enable/disable debugging for MPLS LDP

Operation Command
debugging mpls ldp { all | main | advertisement |
Enable debugging for
session | pdu | notification | remote }[ interface
MPLS LDP
interface-type interface-number ]
undo mpls debugging ldp { all | main | advertisement |
Disable debugging for
session | pdu | notification | remote } [ interface
MPLS LDP
interface-type interface-number]

Use the mpls ldp reset-session command in VLAN interface to reset a specific LDP
session on the VLAN interface.

Huawei Technologies Proprietary

2-11
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

Table 2-24 Reset LDP

Operation Command
Reset a specific LDP session on the
mpls ldp reset-session peer-address
VLAN interface (VLAN interface view)

2.5 Typical MPLS Configuration Example

I. Network requirements

Figure 2-1 illustrates a network with four switches, which connects to each other
through Ethernet.
The four switches all support MPLS, and LSP can be established between any two
switches with the routing protocol OSPF.LDP establishes LSP by using routing
information of OSPF.

II. Network diagram

SwitchB
VLAN201 VLAN203
Switch A 168.1.1.2 172.17.1.1 SwitchD
VLAN202
VLAN201 100.10.1.2
VLAN203
168.1.1.1 172.17.1.2

VLAN202
100.10.1.1

SwitchC

Figure 2-1 Network diagram

III. Configuration procedure

1) Configure Switch A
# Configure LSR ID and enable MPLS and LDP.
[Quidway] mpls lsr-id 168.1.1.1
[Quidway] mpls
[Quidway-mpls] quit
[Quidway] mpls ldp

# Configure IP address and enable MPLS and LDP for VLAN interface 201.
[Quidway] vlan 201

Huawei Technologies Proprietary

2-12
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

[Quidway-vlan201] port gigabitethernet 2/1/1

[Quidway-vlan201] quit
[Quidway] interface Vlan-interface 201
[Quidway-Vlan-interface201] ip address 168.1.1.1 255.255.0.0
[Quidway-Vlan-interface201] mpls
[Quidway-Vlan-interface201] mpls ldp enable
[Quidway-Vlan-interface201] mpls ldp transport-ip interface

# Enable OSPF on the interface connecting Switch A with Switch B.

[Quidway] Router id 168.1.1.1
[Quidway] ospf
[Quidway-ospf-1] area 0
[Quidway-ospf-1-area-0.0.0.0] network 168.1.0.0 0.0.255.255
2) Configure Switch B
# Configure LSR ID and enable MPLS and LDP.
[Quidway] mpls lsr-id 172.17.1.1
[Quidway] mpls
[Quidway-mpls] quit
[Quidway] mpls ldp

# Configure IP address and enable MPLS and LDP for VLAN interface 201.
[Quidway] vlan 201
[Quidway-vlan201] port gigabitethernet 2/1/1
[Quidway-vlan201] quit
[Quidway] interface vlan-interface 201
[Quidway-Vlan-interface201] ip address 168.1.1.2 255.255.0.0
[Quidway-Vlan-interface201] mpls
[Quidway-Vlan-interface201] mpls ldp enable
[Quidway-Vlan-interface201] mpls ldp transport-ip interface

# Configure IP address and enable MPLS and LDP for VLAN interface 203.
[Quidway] vlan 203
[Quidway-vlan203] port gigabitethernet 2/1/3
[Quidway-vlan203] quit
[Quidway] interface vlan-interface 203
[Quidway-Vlan-interface203] ip address 172.17.1.1 255.255.0.0
[Quidway-Vlan-interface203] mpls
[Quidway-Vlan-interface203] mpls ldp enable
[Quidway-Vlan-interface203] mpls ldp transport-ip interface

# Configure IP address and enable MPLS and LDP for VLAN interface 202.
[Quidway] vlan 202
[Quidway-vlan202] port gigabitethernet 2/1/2
[Quidway-vlan202] quit

Huawei Technologies Proprietary

2-13
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

[Quidway] interface Vlan-interface 202

[Quidway-Vlan-interface202] ip address 100.10.1.2 255.255.255.0
[Quidway-Vlan-interface202] mpls
[Quidway-Vlan-interface202] mpls ldp enable
[Quidway-Vlan-interface202] mpls ldp transport-ip interface
[Quidway-Vlan-interface202] quit

# Enable OSPF on the interfaces respectively connecting Switch B with Switch A,

Switch D and Switch C.
[Quidway] Router id 172.17.1.1
[Quidway] ospf
[Quidway-ospf-1] area 0
[Quidway-ospf-1-area-0.0.0.0] network 168.1.0.0 0.0.255.255
[Quidway-ospf-1-area-0.0.0.0] network 172.17.0.0 0.0.255.255
[Quidway-ospf-1-area-0.0.0.0] network 100.10.1.0 0.0.0.255
[Quidway-ospf-1-area-0.0.0.0] quit
3) Configure Switch C
# Configure LSR ID and enable MPLS and LDP.
[Quidway] mpls lsr-id 100.10.1.1
[Quidway] mpls
[Quidway-mpls] quit
[Quidway] mpls ldp

# Configure IP address and enable LDP and MPLS for VLAN interface 202.
[Quidway] vlan 202
[Quidway-vlan202] port gigabitethernet 2/1/1
[Quidway-vlan202] quit
[Quidway] interface Vlan-interface 202
[Quidway-Vlan-interface202] ip address 100.10.1.1 255.255.255.0
[Quidway-Vlan-interface202] mpls
[Quidway-Vlan-interface202] mpls ldp enable
[Quidway-Vlan-interface202] quit

# Enable OSPF on the interface connecting Switch C with Switch B.

[Quidway] Router id 100.10.1.1
[Quidway] ospf
[Quidway-ospf-1] area 0
[Quidway-ospf-1-area-0.0.0.0] network 100.10.1.0 0.0.0.255
4) Configure Switch D
# Configure LSR ID and enable MPLS and LDP.
[Quidway] mpls lsr-id 172.17.1.2
[Quidway] mpls
[Quidway-mpls] quit

Huawei Technologies Proprietary

2-14
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 2 MPLS Basic Capability Configuration

[Quidway] mpls ldp

# Configure IP address and enable MPLS and LDP for VLAN interface 203.
[Quidway] vlan 203
[Quidway-vlan203] port gigabitethernet 2/1/3
[Quidway-vlan203] quit
[Quidway] interface vlan-interface 203
[Quidway-Vlan-interface203] ip address 172.17.1.2 255.255.0.0
[Quidway-Vlan-interface203] mpls
[Quidway-Vlan-interface203] mpls ldp enable

# Enable OSPF on the interface connecting Switch D with Switch B.

[Quidway] Router id 172.17.1.2
[Quidway] ospf
[Quidway-ospf-1] area 0
[Quidway-ospf-1-area-0.0.0.0] network 172.17.0.0 0.0.255.255

2.6 Troubleshooting MPLS Configuration

Symptom: Session cannot be setup with the peer after LDP is enabled on the interface.
Troubleshooting:
Cause 1: Loop detection configuration is different at the two ends.
Solution: Check loop detection configuration at both ends to see if one end is
configured while the other end is not (this will result in session negotiation failure).
Cause 2: Local machine cannot get the route to peer LSR ID, so TCP connection
cannot be set up and session cannot be established.
Solution: The default address for session transfer is MPLS LSR ID. The local machine
should issue the LSR ID route (often the Loopback address) and lean the peer LSR ID
route.

Huawei Technologies Proprietary

2-15
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Chapter 3 BGP/MPLS VPN Configuration

3.1 BGP/MPLS VPN Overview

Traditional VPN, for which layer 2 tunneling protocols (L2TP, L2F and PPTP, and so on.)
or layer 3 tunnel technology (IPSec, GRE and so on.) is adopted, is a great success
and is therefore widely used. However, along with the increase of the size of VPNs , the
deficiency of traditional VPN in such aspects as expansibility and manageability
becomes more and more obvious. In addition, QoS (Quality of Service) and security
are also the difficult problem for traditional VPN.
Using the MPLS technology, service providers can implement the IP-based VPN
services easily and enable their networks to meet the expansibility and manageability
requirement for VPN. The VPN constructed by using MPLS also provides the possibility
for the implementation of value-added service. Multiple VPNs can be formed from a
single access point, and each VPN represents a different service, making the network
able to transmit services of different types in a flexible way.
Product currently provides comparatively complete BGP/MPLS VPN networking
capabilities:
z Address isolation, allowing the overlap of address of different VPNs and public
networks.
z Supporting MBGP advertising VPN routing information through public network,
establishing BGP/MPLS VPN.
z Forwarding VPN data stream over MPLS LSP.
z Providing MPLS VPN performance monitoring and fault detecting tools.

Huawei Technologies Proprietary

3-1
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3.1.1 BGP/MPLS VPN Model

I. BGP/MPLS VPN model

VPN1 site 1
site 1 Backbone network of
PE the service provider CE
P P
CE
PE VPN 2

CE
site 2

VPN2
P
site 3 PE VPN1
PE
site 2
CE
CE

Figure 3-1 MPLS VPN model

As shown in Figure 3-1, MPLS VPN model contains three parts: CE, PE and P.
z CE (Customer Edge) device: It is a composing part of the customer network, which
is usually connected with the service provider directly through an interface. It may
be a router or a switch which cannot sense the existence of VPN.
z PE (Provider Edge) router: It is the Provider Edge router, namely the edge device
of the provider network, which connects with your CE directly. In MPLS network,
PE router processes all the operations for VPN.PE needs to possess MPLS basic
forwarding capability.
z P (Provider) router: It is the backbone router in the provider network, which is not
connected with CE directly. P router needs to possess MPLS basic forwarding
capability.
The classification of CE and PE mainly depends on the range for the management of
the provider and the customer, and CE and PE are the edges of the management
ranges.

II. Nested BGP/MPLS VPN model

In a basic BGP/MPLS VPN model, the PEs are in the network of the service provider
and are managed by the service provider.
When a VPN user wants to subdivide the VPN into multiple VPNs, the traditional
solution is to configure these VPNs directly on the PEs of the service provider. This
solution is easy to implement, but has the following disadvantages: the number of the
VPNs carried on PEs may increase rapidly; the operator may have to perform more
operations when required by a user to adjust the relation between the user's internal

Huawei Technologies Proprietary

3-2
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

VPNs. These disadvantages not only increase the network operating cost, but also
bring relevant management and security issues.
The nested VPN is a better solution. Its main idea is to transfer VPNv4 route between
PE and CE of common BGP MPLS/VPN such that user themselves can manage their
internal VPN division, and the service provider can be saved from participating into
users' internal VPN management.
The following figure shows the network model for nested VPN:
CE5
VPN1
provider PE provider PE
CE6
P
VPN2
CE7

VPN3

customer VPN customer VPN

customer PE customer PE

CE1 CE2 CE3 CE4

VPN1 VPN2 VPN1 VPN3

Figure 3-2 Network model for nested BGP/MPLS VPN

III. Basic concepts in BGP/MPLS VPN

1) VPN-instance
VPN-instance is an important concept in VPN routing in MPLS. In an MPLS VPN
implementation, each site corresponds to a specific VPN-instance on PE (their
association is implemented by binding VPN-instance to the VALN interface). If
subscribers on one site belong to multiple VPNs, then the corresponding VPN-instance
includes information about all these VPNs.
Specifically, such information should be included in VPN-instance: label forwarding
table, IP routing table, the interfaces bound with VPN-instance, and the management
information (RD, route filtering policy, member interface list, and so on). It includes the
VPN membership and routing rules of this site.
PE is responsible for updating and maintaining the relationship between VPN-instance
and VPN. To avoid data leakage from the VPN and illegal data entering into the VPN,
each VPN-instance on the PE has an independent set of routing table and label
forwarding table, in which the forwarding information of the message is saved
2) MBGP
MBGP (multiprotocol extensions for BGP-4, see RFC2283) propagates VPN
membership information and routes between PE routers. It features backward

Huawei Technologies Proprietary

3-3
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

compatibility: It not only supports traditional IPv4 address family, but also supports
other address families, for example, VPN-IPv4 address family. MP-BGP ensures that
VPN private routes are only advertised within VPNs, as well as implementing
communication between MPLS VPN members.
3) VPN-IPv4 address
VPN is just a private network, so it can use the same IP address to indicate different
sites. But the IP address is supposed as unique when MP-BGP advertises CE routes
between PE routers, so routing errors may occur for the different meaning in two
systems. The solution is to switch IPv4 addresses to VPN-IPv4 address to generate
globally unique addresses before advertising them, so PE routers is required to support
MP-BGP.
A VPN-IPv4 address consists of 12 bytes, and the first eight bytes represent the RD
(Route Distinguisher), which are followed by a 4-byte IPv4 address. The service
providers can distribute RD independently. However, their special AS (Autonomous
System) number must be taken as a part of the RD. After being processed in this way,
even if the 4-byte IPv4 address contained in VPN-IPv4 address has been overlapped,
the VPN-IPv4 address can still maintain globally unique. RD is only used within the
carrier network to differentiate routes. When the RD is 0, a VPN-IPv4 address is just a
IPv4 address in general sense.
The route received by PE from CE is the IPv4 route that needs to be redistributed into
VPN-instance routing table, and in this case a RD needs to be added. It is
recommended that the same RD be configured for all routes from the same user site.

IV. VPN Target attribute

VPN Target attribute is one of the MBGP extension community attributes and is used to
limit VPN routing information advertisement. It identifies the set of sites that can use
some route, namely by which Sites this route can be received, and the PE router can
receive the route transmitted by which Sites. The PE routers connected with the site
specified in VPN Target can all receive the routes with this attribute.
For PE routers, there are two sets of VPN Target attributes: one of them, referred to as
Export Targets, is added to the route received from a direct-connect site in advertising
local routes to remote PE routers. And the other one, known as Import Targets, is used
to decide which routes can be imported into the routing table of this site in receiving
routes from remote PE routers.
When matching the VPN Target attribute carried by the route to filter the routing
information received by the PE router, if the export VPN target set of the received route
contains identical items with the import VPN target set of the local end, the route is
imported into the VPN routing table and then advertised to the connected CE .
Otherwise, the route will be rejected.

Huawei Technologies Proprietary

3-4
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

ERT: Export Route Targets

RD IPv4 address ... ERT1 ERT2 ... ERTn

MPLS VPN Route

Import Route Targets:
( IRT1, IRT2, ... ,IRTm )

Figure 3-3 Route filtering through matching VPN Target attribute

Note:
The routes for other VPNs will not appear in the VPN's routing table by using VPN
Target attribute to filter routing information received at PE router, so the CE-transmitted
data will only be forwarded within the VPN.

3.1.2 BGP/MPLS VPN Implementation

BGP/MPLS VPN works on this principle: It uses BGP to propagate VPN private routing
information on carrier backbone network, and uses MPLS to forward VPN service
traffic.
The following are introductions to BGP/MPLS implementation from two aspects:
advertising VPN routing information and forwarding VPN packets.

I. Advertising VPN routing information

Routing information exchange has the following four types:

1) Between CE and PE
A PE router can learn routing information about the CE connected to it through static
route, RIP (supporting multi-instance), OSPF (supporting multi-instance) or EBGP, and
imports it in a vpn-instance.
2) Between ingress PE and egress PE
The ingress PE router uses MP-BGP to send information across public network: It
advertises routing information learned from CE to the egress PE router (with MPLS
label) and learns the CE routing information learned at the egress PE router.
The internal connectivity among the VPN internal nodes is ensured through enabling
IGP (for example, RIP and OSPF) or configuring static routes on the PEs.
3) LSP setup between PEs

Huawei Technologies Proprietary

3-5
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

LSPs must be set up between PEs for VPN data traffic forwarding with MPLS LSP. The
PE router which receives packets from CE and create label protocol stack is called
Ingress LSR, while the BGP next hop (Egress PE router) is Egress LSR. Using LDP to
create fully connected LSPs among PEs.
4) Between PE and CE
A CE can learn remote VPN routes from the PE connected through static routes, RIP,
OSPF or EBGP.
With above-mentioned steps, reachable routes can be established between CEs, for
transmission of VPN private routing information over public network.

II. Forwarding VPN packets

On the ingress PE, two-layer label stack is formed for each VPN packet:
Interior-layer label, also called MPLS label, is at the bottom of the label stack and
distributed by M-BGP when the egress PE advertises routing information (in VPN
forwarding table) to ingress GE. When VPN packets from public network reach the CE,
they can be forwarded from the designated interface to the designated CE or site by
searching for the target MPLS forwarding table according to the labels contained.
Exterior-layer label, known as LSP initialization label, distributed by MPLS LDP, is at
the top of the label stack and indicates an LSP from the ingress PE to egress PE. By the
switching of exterior-layer label, VPN packets can be forwarded along the LSP to the
peer PE.
Figure 3-4 illustrates the details:

Layer1

1.1.1.2 Layer2 Layer2 1.1.1.2

1.1.1.2 1.1.1.2
CE1 CE2
PE1 PE2

P P
site1 site2

1.1.1.1/24 1.1.1.2/24

Figure 3-4 Forwarding VPN packets

1) Site 1 sends an IPv4 packet with the destination address 1.1.1.2 of to CE1. CE1
looks up the IP routing table for a matched entry and sends the packet to PE1
according to the matched entry.
2) Depending on the interface the packet reaches and the destination of it, PE1 looks
up the VPN-instance entry to obtain interior-layer label, exterior-layer label, BGP
next hop (PE2), and output interfaces. After the establishment of labels, PE1
forwards MPLS packets to the first P of LSP through output interface.

Huawei Technologies Proprietary

3-6
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3) Each P router on LSP forwards MPLS packets using exterior-layer label to the
penultimate-hop router, namely the P router before PE2. The penultimate-hop
router extracts the exterior-layer and sends MPLS packet to PE2.
4) PE2 looks up in the MPLS forwarding table according to the interior-layer label and
destination address to determine the egress interface for labeling operation and
the packet. It then extracts the interior-layer label and forwards through the egress
interface the IPv4 packet to CE2.
5) CE2 looks up in the routing table and sends the packet in normal IPv4 packet
forwarding mode to the site2.

3.1.3 Nested BGP/MPLS VPN Implementation

When implementing a nested BGP/MPLS VPN, pay attention to the following items:
z No address overlap is allowed between user's internal sub-VPNs.
z To ensure the VPN routing information is correctly advertised over the backbone
network, the VPN-Targets of the user VPN and the internal sub-VPNs cannot be
overlapped and must be specified by the service provider.
z The provider PE and the customer PE must be directly connected and cannot
exchange VPNv4 route in Multihop-EBGP mode.
Before configuring a nested BGP/MPLS VPN, you must complete the following tasks:
z Configuring IGP on the MPLS backbone network (including provider PE and P
routers) to implement the IP connectivity on the backbone network.
z Configuring basic MPLS capability on the MPLS backbone network.
z Configuring MPLS LDP and setting up LDP LSP on the MPLS backbone network.
z Configuring BGP on the MPLS backbone network (create IBGP peers between
provider PEs).
z Configuring basic MPLS capability on user-end network (including customer PEs).

3.1.4 Hierarchical BGP/MPLS VPN Implementation

As PE is required to aggregate multiple VPN routes on a BGP/MPLS VPN, it is prone to

forming a bottleneck in a large-scale deployment or in the case that PE capacity is
small. To solve the problem, Huawei Technologies introduced the HoVPN (Hierarchy of
VPN, Hierarchical BGP/MPLS VPN) solution.
Hierarchical BGP/MPLS VPN divides an MPLS VPN into several MPLS VPNs in a
hierarchical network structure. Each VPN takes on a role depending on its level. There
are high performance requirements in routing and forwarding on the PEs at the higher
level of MPLS VPN, because they are primarily used for connecting the backbone
networks and providing access service for huge VPN clients. However, such
requirements are relatively low for PEs at the lower level of the network as they
primarily function to access the VPN clients at the edges. Congruous with the IP
network model, HoVPN model improves the scalability of BGP/MPLS VPN, and hence

Huawei Technologies Proprietary

3-7
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

allows lower-layer MPLS VPNs comprising low-end equipment to provide MPLS VPN
accessing and interconnect through the high-end MPLS VPN backbone.
As shown in Figure 3-5, the PEs directly connected with user devices are called UPE
(underlayer PE or user-end PE); the devices in the core network connected with the
UPEs are called SPE (superstratum PE or service-provider-end PE).
Hierarchical PEs have the same appearance as that of the traditional PEs and can
coexist with other PEs in the same MPLS network.
UPEs are responsible for user access; they only maintain the routes of directly
connected VPN sites, but not that of the remote sites. SPEs, however, are responsible
for the maintenance and advertisement of VPN routes; they maintain all the routes of
the VPNs connected by their UPEs, including the routes in both local and remote sites.
UPE and SPE are relative concepts. In a multi-layer PE architecture, an upper layer PE
is an SPE for its lower layer PE, and a lower layer PE is an UPE for its upper layer PE.
The MBGP runs between SPE and UPE can be either MP-IBGP or MP-EBGP,
depending on whether the SPE and the UPE are in the same AS.

PE MPLS backbone
MPLS 骨干网 PE
Upper VPN network

SPE

Lower VPN
UPE
UPE

VPN1 Site1 VPN2 Site1 VPN1 Site1

VPN2 Site1

CE CE CE CE

Figure 3-5 Hierarchical BGP/MPLS VPN

3.1.5 Introduction to OSPF Multi-instance

As one of the most popular IGP routing protocols, OSPF is used as an internal routing
protocol in many VPNs. Using OSPF on PE-CE links brings convenience to you
because in this case CE routers only need to support OSPF protocol, without the need
of supporting other protocols, and network administrator only have to know the OSPF
protocol. If you want to transform conventional OSPF backbone into BGP/MPLS VPN,
using OSPF between PE and CE can simplify this transform process.
Therefore IETF raised two new OSPF VPN extension drafts, to provide a complete
solution to SPPF problems in BGP/MPLS VPN application when OSPF is used as

Huawei Technologies Proprietary

3-8
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

PE-CE routing protocol. In this case, PE router must be able to run multiple OSPF
instances, each of which corresponds to one VPN instance, owns an individual
interface, routing table, and sends VPN routing information over MPLS network using
BGP/OSPF interaction.
If supporting OSPF multi-instance, one router can run multiple OSPF processes, which
can be bound to different VPN instances. In practice, you can create one OSPF
instance for each service type. OSPF multi-instance can fully isolate different services
in transmission, which can solve security problems with low cost to meet the needs of
customers. Generally, OSPF multi-instance is run on PEs; The CE running OSPF
multi-instance in the LAN is called multi-VPN-instance CE. At present, isolation of LAN
services implements by VLAN function of the switch. OSPF Multi-VPN-Instance CE
provides schemes of services isolation implemented on routers.

VPN-GREEN
VPN -GREEN
Site2
Site2
OSPFArea2
OSPF Area2 CE31
VPN --RED
VPN RED
Area 2
Site1
Site1 PE3
OSPF Area0
OSPF Area0 OSPF 100 VPN -GREEN

CE21
CE11 VPN-RED
VPN -RED
Area 0 Site2
Site2
OSPF 100 VPN - RED OSPF Area1
OSPF Area1
MPLSVPN
MPLS VPNBac
Backbone
kbone Area 0
OSPF 200 VPN -GREEN OSPF 100 VPN -RED
Area 1
PE1
OSPF 200 VPN -GREEN
Area 1
VPN-GREEN
VPN-GREEN CE12 PE2
Site1
Site1 CE22
OSPF Area1
OSPF Area1

Figure 3-6 OSPF multi-instance application in MPLS/BGP VPN PE

Engineering

ospf 100
vpn-engineering
ospf 100
vpn-engineering
MPLS Network opsf 200 opsf 200
vpn-rd vpn-rd R&D
ospf 300
PE vpn-finances
Multi-VPN-Instance CE
ospf 300
vpn-finances Finances

Figure 3-7 Multi-VPN-instance CE application in conventional LAN

3.1.6 Introduction to Multi-Role Host

The VPN attribute of the packets from a CE to its PE lies on the VPN bound with the
ingress interface. This, in fact determines that all the CEs forwarded by the PE through
the same ingress interface belong to the same VPN; but in actual network
environments, a CE may need to access multiple VPNs through one physical interface.

Huawei Technologies Proprietary

3-9
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Though you can configure different logical interfaces to meet this need, this
compromised method brings additional configuration burden and has limitation in
actual use.
To resolve this problem, the idea of multi-role host is generated. Specifically to say, this
idea is to differentiate the accesses to different VPNs through configuring policy routing
based on IP addresses, and transmit downstream data flow from PE to CE by
configuring static routing. The static routing under multi-role host circumstance is
different from common hosts; it is implemented by specifying an interface of another
VPN as the egress interface through a static route in a VPN; and thus allowing one
logical interface to access multiple VPNs.

3.2 BGP/MPLS VPN Configuration

3.2.1 3.2.1 Configuring Various Kinds of Routers

Implementing BGP/MPLS VPN functions requires the following procedures in general:

Configure basic information on PE, CE and P; establish the logical or physical link with
IP capabilities from PE to PE; advertise and update VPN network information.

I. CE router

The configuration on CE is relative simple. Only static route, RIP, OSPF or EBGP
configuration is needed for VPN routing information exchange with the PE connected,
MPLS configuration is not needed.

II. PE router

The configuration on PE is relative complex. After the configuration, the PE implements

MPLS/BGP VPN core functions.
The following sections describe the configuration tasks on a PE device:
z Configuring basic MPLS capability
z Defining BGP/MPLS VPN site
z Configuring PE-CE route exchanging
z Configuring PE-PE route exchanging

III. P router

The configuration on P device is relative simple. The main task is to configure MPLS
basic capacity on the P device to support LDP and MPLS forwarding.
The following are detailed configurations.

Huawei Technologies Proprietary

3-10
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3.2.2 Configuring CE Router

As a customer-side device, only basic configuration is required on a CE router, for

routing information exchange with PE router. Currently route switching modes available
include static route, RIP, OSPF, EBGP, and so on.

I. Creating static route

If you select static route mode for CE-PE route switching, you should then configure a
private static route pointing to PE on CE.
Perform the following configuration in the system view.

Table 3-1 Create/delete a static route in VPN instance routing table

Operation Command
Create a specified ip route-static ip-address { mask | mask-length }
VPN-instance static { interface-name | gateway-address } [ preference
route preference-value ] [ reject | blackhole ]
Delete a specified undo ip route-static ip-address { mask | mask-length }
VPN-instance static [ interface-name | gateway-address ] [ preference
route preference-value ]

By default, the preference value for a static route is 60. You can also specify preference
for a static route.

II. Configuring RIP

If you select RIP mode for CE-PE route switching, you should then configure RIP on CE.
For detailed RIP configuration steps, see the RIP configuration part in routing protocol
in Quidway S8500 Series Routing Switches Operation Manual Volume I.

III. Configuring OSPF

If you select OSPF mode for CE-PE route switching, you should then configure OSPF
on CE. For configuring OSPF, see the routing protocol part in Quidway S8500 Series
Routing Switches Operation Manual Volume II.
You must configure OSPF multi-instance to isolate services of different VPNs on CE
router, which is now called Multi-VPN-Instance CE.
You can bind OSPF processes with VPN with the following command in OSPF view.

Table 3-2 Configure the router as multi-VPN-instance CE

Operation Command
Configure the router as multi-VPN-instance CE vpn-instance-capability simple
Remove the configuration undo vpn-instance-capability

Huawei Technologies Proprietary

3-11
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

IV. Configuring EBGP

If you select BGP mode for CE-PE route switching, you should then configure EBGP
peer, import direct-connect route, static route and other IGP routes, for BGP to
advertise VPN routes to PE.

3.2.3 Configuring PE Router

I. Configuring basic MPLS capability

It includes configuring MPLS LSR ID, enable MPLS globally and enable MPLS in the
corresponding VLAN interface view.
Refer to Chapter 2 MPLS Basic Capacity Configuration for details.

II. Defining BGP/MPLS VPN site

1) Create VPN-instance and enter VPN-instance view

The VPN instance is associated with a site. The VPN membership and routing rules of
a site is configured in the corresponding VPN instance.
This command is used to create a new VPN-instance and enter the VPN-instance view,
or directly enter the VPN-instance view if the VPN-instance already exists.
Perform the following configuration in the system view.

Table 3-3 Create a VPN-instance and enter VPN-instance view

Operation Command
Create a VPN-instance and enter
ip vpn-instance vpn-instance-name
VPN-instance view
Delete a VPN-instance undo ip vpn-instance vpn-instance-name

By default, no VPN-instance is defined.

2) Configure RD for the vpn-instance
After PE router is configured with RD, when a VPN route learned from CE is imported
into BGP, BGP attaches the RD in front of the IPv4 address. Then the general IPv4
address which may overlaps between several VPN IPv4 addresses in the VPN is
turned into a globally unique VPN IPv4 address and thus ensure the correct routing in
the VPN.
Perform the following configuration in VPN-instance view.

Table 3-4 Configure RD for the VPN-instance

Operation Command
Configure RD for the VPN-instance route-distinguisher route-distinguisher

Huawei Technologies Proprietary

3-12
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

The parameter in the above command has no default value. A VPN-instance works only
when a RD is configured for it. Other parameters for a VPN-instance cannot be
configured before configuring a RD for it.
To modify the RD, you must first delete the VPN-instance and reconfigure it.
3) Configure VPN-instance description
Perform the following configuration in VPN-instance view

Table 3-5 Configure VPN-instance description

Operation Command
Configure VPN-instance description description vpn-instance-description
Delete VPN-instance description undo description

4) Configure VPN-target attribute for the VPN-instance

VPN-target attribute, a BGP extension community attribute, controls advertisement of
VPN routing information.
The following is the advertisement controlling process of VPN routing information:
z When BGP is imported into a VPN route learned at CE, it associates a VPN-target
extension community attribute list for the route. Usually the list is the VPN-instance
output routing attribute list which is associated with CE.
z VPN instance defines input routing attribute list according to the
import-extcommunity in VPN-target, defines the acceptable route range and
import it.
z VPN instance modifies VPN-target attributes for the routes to be advertised,
according to the export-extcommunity in VPN-target.
Like an RD, an extension community includes an ASN plus an arbitrary number or an IP
address plus an arbitrary number. There are two types of formats:
The first one is related to autonomous system number (ASN), in the form of 16-bit ASN
(can be 0 here): 32-bit user-defined number, for example, 100:1.
The second one is related to IP address, in the form of 32-bit IP address (can be 0.0.0.0
here):16-bit user-defined number, for example, 172.1.1.1:1.
Perform the following configuration in the VPN-instance view.

Table 3-6 Create VPN-target extended community for the VPN-instance

Operation Command
vpn-target vpn-target-extcommunity
Configure VPN-target extended
[ import-extcommunity |
community for the VPN-instance
export-extcommunity | both ]

Huawei Technologies Proprietary

3-13
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Operation Command
undo vpn-target
Delete the specified VPN-target
vpn-target-extcommunity
attribute from the VPN-target attribute
[ import-extcommunity |
list associated with the VPN-instance
export-extcommunity | both ]

By default, the value is both. In general all Sites in a VPN can be interconnected, and
the import-extcommunity and export-extcommunity attributes are the same, so you
can execute the command only with the both option.
Up to 16 VPN-targets can be configured with a command, and up to 20 vpn-targets can
be configured for a VPN-instance.
5) Limit the maximum number of routes in a VPN-instance
This command is used to limit the maximum number of routes for a VPN-instance so as
to avoid too many routes imported from a Site.
Perform the following configuration in the VPN-instance view.

Table 3-7 Limit the maximum number of routes in the VPN-instance

Operation Command
Limit the maximum number of routes in routing-table limit integer
the VPN-instance { alarm-integer | syslog-alert }
Remove the maximum number limitation undo routing-table limit

Integer is in the range of 1 to 65536 and alarm-integer is in the range of 1 to 100.

Note:
Changing the maximum route limit for VPN-instance will not affect the existing routing
table. To make the new configuration take effect immediately, you should rebuild the
corresponding routing protocol or perform shutdown/undo shutdown operation on
the corresponding interface.

6) Configure vlan-id larger than 1024 on the fast Ethernet port of Trunk type
(Optional)
Configure vlan-id larger than 1024, with the range of MPLS/VPN VLANs allowed to
pass the port from vlan-id to vlan-id + 1023
Perform the following configuration in Ethernet port view.

Huawei Technologies Proprietary

3-14
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Table 3-8 Configure the vlan id range of MPLS/VPN VLANs allowed to pass the
Ethernet port of C card

Operation Command
Configure the vlan id range of MPLS/VPN
port trunk mpls vlan from vlan-id [ to ]
VLANs allowed to pass the Trunk fast
vlanid
Ethernet port
Remove the configured vlan id range of
MPLS/VPN VLANs allowed to pass the undo port trunk mpls
Trunk fast Ethernet port

By default, the vlan-id range of MPLS/VPN VLANs is from 0 to 1023, and the default
value of vlan-id is 0. The value range of vlan-id is from 1 to 3071.

Caution:

z This command is only applicable to fast Ethernet ports of C cards.

z This command can only be executed on Trunk ports, and MPLS/VPN enabled
VLANs and VLANs out of the configured range are excluded (a Trunk port contains
VLAN1 by default, so it is not judged).

7) Associate interface with VPN-instance

VPN instance is associated with the direct-connect Site through interface binding.
When the packets from the Site reach the PE router though the interface bound, then
the PE can look routing information (including next hop, label, egress interface, and so
on.) up in the corresponding VPN-instance.
This command can associate a VPN-instance with an interface.
Perform the following configuration in VLAN interface view.

Table 3-9 Associate interface with VPN-instance

Operation Command
ip binding vpn-instance vpn-instance-
Associate interface with VPN-instance
name
Remove the association of the interface undo ip binding vpn-instance vpn-inst
with VPN-instance ance-name

Huawei Technologies Proprietary

3-15
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Caution:

As executing the ip binding vpn-instance command on an interface will delete the IP

address of the interface, you must configure the IP address of the interface after
executing that command when you bind the interface with a VPN-instance.

III. Configuring PE-CE route exchanging

These route exchanging modes are available between PE and CE: static route, RIP,
OSPF, EBGP.
1) Configure static route on PE
You can configure a static route pointing to CE on PE for it to learn VPN routing
information from CE.
Perform the following configuration in the system view.

Table 3-10 Create/Delete static route in VPN-instance routing table

Operation Command

ip route-static vpn-instance vpn-instance-name1

Create the static vpn-instance-name2 … ip-address { mask | mask-length }
route of a specific { interface-name | [ vpn-instance vpn-nexthop-name
VPN-instance vpn-nexthop-address ] } [ preference preference-value |
public ] [ reject | blackhole ]

undo ip route-static vpn-instance vpn-instance-name1

Delete a static vpn-instance-name2 … ip-address { mask | mask-length }
route of a specific { interface-name [ vpn-instance vpn-nexthop-name
VPN-instance vpn-nexthop-address ] } [ preference preference-value |
public ] [ reject | blackhole ]

By default, the preference value for a static route is 60. You can also specify another
preference for the static route you are configuring.
2) Configure RIP multi-instance
If you select RIP mode for CE-PE route switching, you should then specify running
environment for RIP instance on PE. With this command, you can enter RIP view and
import and advertise RIP instance in the view.
Perform the following configuration in the RIP view.

Huawei Technologies Proprietary

3-16
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Table 3-11 Configure PE-CE RIP instance

Operation Command
ipv4-family [ unicast ] vpn-instance
Create PE-CE RIP instance
vpn-instance-name
undo ipv4-family [ unicast ] vpn-instance
Delete PE-CE RIP instance
vpn-instance-name

Then configuring RIP multi-instance to import IBGP route.

For details about RIP configuration, see RIP configuration section in Routing Protocol
of this manual.
3) Configure OSPF multi-instance on PE
If you select OSPF mode for CE-PE route switching, you should then configure OSPF
multi-instance on PE. Other configurations, such as MPLS basic configuration,
VPN-instance configuration, do not change. Noted that when OSPF routes and
direct-connect routes are imported in the VPN instance address family view, BGP
routes should also be imported into OSPF. Here only introduces OSPF multi-instance
configuration in detail.
First step: Configure OSPF process.
Perform the following configuration in the system view.

Table 3-12 Configure OSPF process

Operation Command
ospf process-id [ router-id router-id-number ]
Configure an OSPF process
[ vpn-instance vpn-instance-name ]
Delete an OSPF process undo ospf process-id

By default, the process index is 1.

Caution:

An OSPF process can only belong to one VPN instance, while one VPN instance may
contain multiple OSPF processes. By default, an OSPF process belongs to public
network.

Step 2: Configure Domain ID

The Domain ID is used to identify an OSPF autonomous system (AS), and the same
OSPF domain must have the same Domain ID. One process can be configured with

Huawei Technologies Proprietary

3-17
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

only one Domain ID; different processes can be configured with the same Domain ID or
different Domain IDs.
Perform the following configuration in the OSPF view.

Table 3-13 Configure Domain ID

Operation Command
Configure Domain ID domain-id { id-number | id-addr }
Return to the default value undo domain-id

By default, id-number is 0 and id-addr is 0.0.0.0.

It is recommended that all OSPF instances in a VPN are configured with either the
same domain ID or the default value.

Caution:

The configured value will not take effect unit the command reset ospf is executed.

Step 3: Configure tag for imported VPN route (optional)

If a VPN Site links to multiple PEs, routing ring may present when the routes learned by
MPLS/BGP are received by another PE router in being advertised by category-5/-7 LSA
of a PE to the VPN Site. To solve this problem, you should configure Route-tag. It is
recommended to configure identical Route-tag for the PEs in the same VPN.
Perform the following configuration in the OSPF view.

Caution:

The configured Route-tag will not take effect unit the command reset ospf is executed.

Table 3-14 Configure tag for imported VPN route

Operation Command
Configure tag for imported VPN route route-tag tag-number

Return to the default value undo route-tag

Huawei Technologies Proprietary

3-18
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

tag-number is used to identify Tag value; by default, the first two bytes are fixed, that is,
0xD000, and the last two bytes is AS number of local BGP. For example, the AS
number of local BGP is 100, and then its default tag value is 3489661028 in decimal
notation. This value is an integer ranging from 0 to 4294967295.
Step 4: Configure Sham-link (optional)
Sham-links are required between two PEs when Backdoor links (that is, the OSPF links
that do not pass through the MPLS backbone network) exist between the two PEs and
data is expected to be transported over the MPLS backbone. A Sham-link between two
PEs is considered as a link in OSPF domain. Its source and destination addresses are
both the Loopback interface address with 32-bit mask, but this Loopback interface
should be bound to a VPN instance and direct routes must be imported into BGP by
BGP. OSPF processes of the VPN cannot directly import the routes of the Loopback
interface (so the import direct command cannot be executed in an OSPF processes of
VPN); instead, an OSPF process can only advertise the route indirectly by importing a
BGP route.
Perform the following configuration in the OSPF area view.

Table 3-15 Configure Sham-link

Operation Command
sham-link source-addr destination-addr [ cost cost-value ]
[ simple password | md5 keyid key ] [ dead seconds ]
Configure Sham-link
[ hello seconds ] [ retransimit seconds ] [ trans-delay
seconds ]
Delete a Sham-link undo sham-link source-addr destination-addr

By default, the cost value is 1, dead value is 40 seconds, hello value is 10 seconds,
retransmit value is 5 seconds and trans-delay value is 1 second.
4) Configure EBGP on PE
If you select EBGP between PE and CE, you should configure a neighbor for each VPN
in VPN instance address family sub-view, and import IGP route of CE.
Step 1: Configure peer group
Configuring peer group in VPN instance address family view.

Table 3-16 Configure peer group

Operation Command
Configure a peer group group group-name [ internal | external ]
Delete the specified peer group undo group group-name

Huawei Technologies Proprietary

3-19
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

By default, the peer group is configured as internal. When BGP mode is used for
PE-CE route switching, they often belong to different ASs, so you should configure
EBGP peer as external.
Step 2: Configure AS number for a specific neighbor and add group member to a peer
group
When EBGP mode is used for PE-CE route switching, you should configure AS number
for a specific neighbor for every CE VPN-instance.
Perform the following configuration in VPN instance address family view.

Table 3-17 Configure AS number for a specific neighbor

Operation Command
Configure AS number for peer { group-name | [ peer-address group
a specific neighbor group-name ] } as-number as-number
Delete the AS number of a undo peer { group-name | [peer-address group
specific neighbor group-name ] } as-number as-number]

Step 3: Activate peer (group)

By default, BGP neighbor is active while MBGP neighbor is inactive. You should
activate MBGP neighbor in VPNv4 sub-address family view.
Perform the following configuration in VPNv4 sub-address family view.

Table 3-18 Activate/deactivate peer (group)

Operation Command
Activate the peer (group) peer group-name enable
Deactivate the peer (group) undo peer group-name enable

Step 4: Configure MBGP to import VPN route of direct-connect CE

To advertise correct VPN route over public network to other PEs with which BGP
adjacency has been created, a PE must import the VPN routing information of the
direct-connect CE into its MBGP routing table.
For example, if a static route is used between PE and CE, PE must import a static route
in VPN-instance address family sub-view of MBGP (import-route static). If RIP is run
between PE and CE, PE must import an RIP route in VPN-instance view of MBGP
(import-route rip). If BGP is run between PE and CE, MBGP imports a direct-connect
route.
Perform the following configuration in VPN instance address family sub-view.

Huawei Technologies Proprietary

3-20
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Table 3-19 Import IGP route

Operation Command
Import IGP route import-route protocol [ process-id ] [ med med ]
Remove IGP route import undo import-route protocol

Step 5: Configure BGP as asynchronous.

Perform the following configuration in VPN instance address family sub-view.

Table 3-20 Configure BGP asynchronous with IGP

Operation Command
Configure BGP asynchronous with IGP undo synchronization

By default, BGP is in asynchronous mode.

Step 6: Permit route loop configuration in Hub&Spoke networking (optional)
Generally speaking, PE-CE configuration is completed after you specify the AS number
of neighbor; for the rest configuration, you can keep the system default values.
In the case of standard BGP, BGP tests routing loop via AS number to avoid generating
routing loop. In the case of Hub&Spoke networking, however, PE carries the AS
number of the local autonomous system when advertising the routing information to CE,
if EBGP is run between PE and CE. Accordingly, the updated routing information will
carry the AS number of the local autonomous system when route update is received
from CE. In this case, PE will not accept the route update information.
This phenomenon can be avoided by executing the peer allow-as-loop command,
which makes the PE still receives the route update information containing the local AS
number from CE.
Perform the following configuration in IPv4 instance sub-address family view.

Table 3-21 Configure to allow/disable routing loop

Operation Command
peer { group-name | peer-address }
Configure to allow routing loop
allow-as-loop asn-limit
undo peer { group-name | peer-address }
Configure to disable routing loop
allow-as-loop asn-limit

By default, the received route update information is not allowed to generate loop
information.
Step 7: Configure BGP features.

Huawei Technologies Proprietary

3-21
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

IV. Configuring PE-PE route exchanging

To exchange VPN-IPv4 routing information between PEs, you should configure

MP-IBGP on PEs.
Perform the following configuration in BGP view or PVN instance address family
sub-view.
1) Configure IBGP
These steps are often required.
Step 1: Configure BGP as asynchronous.
Step 2: Configure BGP neighbor.
Note that BGP adjacency is established through Loopback interface and the sub-net
mask must be 32 bits.
Step 3: Permit BGP session over any operable TCP interface.
In general, BGP uses the best local address in TCP connection. To keep TCP
connection available even when the interface involved fails, you can perform the
following configuration to permit BGP session over any interface through which TCP
connection with the peer can be set up. The command here is usually executed
together with the Loopback interface.
Perform the following configuration in VPNv4 sub-address family view.

Table 3-22 Permit BGP session over any operable TCP interface

Operation Command
peer { peer-address | group-name }
Permit BGP session over any operable
connect-interface { interface-type
TCP interface
interface-number }
Use the best local address for TCP undo peer { peer-address |
connection group-name } connect-interface

BGP creates BGP adjacency to the peer end using specific interfaces, which is usually
the loopback interface. Because this interface is always in the up state, thus it reduces
the strike brought by network shock.
2) Configure MP-IBGP
Step 1: Enter protocol address family view.
Perform the following configuration in BGP view.

Huawei Technologies Proprietary

3-22
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Table 3-23 Configure VPNv4 address family

Operation Command
Enter VPNv4 sub-address family view ipv4-family vpnv4 [ unicast ]
Delete VPNv4 sub-address family view
undo ipv4-family vpnv4 [ unicast ]
configuration

Step 2: Configure MBGP neighbor

Configure internal neighbor of MBGP in VPNv4 sub-address family view.

Table 3-24 Configure peer group

Operation Command
Create a peer group group group-name [ internal | external ]
Delete a specific peer group undo group group-name

Choose the internal keyword when using the command to create an IBGP peer group.
Step 3: Activate peer (group)
By default, BGP neighbor is active while MBGP neighbor is inactive. You must enable
MBGP neighbor in VPNv4 sub-address family view.

Table 3-25 Enable/disable IBGP peer group

Operation Command
Enable a peer group peer group-name enable
Disable a specific peer group undo peer group-name enable

Step 4: Configure the local address as the next hop in route advertisement (optional)
Since the default value is no configuration, you must show clearly to add in this
configuration command when configuring MBGP of PE-PE.
Perform the following configuration in VPNv4 sub-address family view.

Table 3-26 Configure the local address as the next hop in route advertisement

Operation Command
peer { peer-address | group-name }
Configure the local address as the
next-hop-localpeer { peer-address |
next hop in route advertisement
group-name } next-hop-local
undo peer { peer-address | group-name }
Remove the configuration
next-hop-local

Huawei Technologies Proprietary

3-23
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Step 5: Transfer BGP update packet without AS number (optional)

Perform the following configuration in VPNv4 sub-address family view.

Table 3-27 Transfer BGP update packet without AS number

Operation Command
Transfer BGP update packet peer { peer-address | group-name }
without AS number public-as-only
Transfer BGP update packet with undo peer { peer-address | group-name }
AS number public-as-only

Step 6: Advertise default route to the peer (group)

This command adds a default route which uses local address as the next hop on the PE
SPE (system processing engine)
Perform the following configuration in VPNv4 sub-address family view.

Table 3-28 Advertise default route to the peer (group)

Operation Command
Advertise default route to the peer peer ip-address default-route-advertise
(group) vpn-instance vpn-instance name
undo peer ip-address
Remove to advertise default route
default-route-advertise vpn-instance
to the peer (group)
vpn-instance name

Step 7: Configure BGP neighbor as the UPE of BGP/MPLS VPN

This command is only used for UPE (User-end PE) of BGP/MPLS VPN.
Configure the following commands in the VPNv4 sub-address family view.

Table 3-29 Configure BGP neighbor as the UPE of BGP/MPLS VPN

Operation Command
Configure BGP neighbor as the
peer peer-address upe
UPE of BGP/MPLS VPN
Disable the configuration undo peer peer-address upe

3.2.4 Configuring P Router

P router does not maintain VPN routes, but do keep connection with public network and
coordinate with PE in creating LSPs. These configurations are required on P router:

Huawei Technologies Proprietary

3-24
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Step 1: Configure MPLS basic capacity and enable LDP on the interfaces connecting P
router to PE router, for forwarding MPLS packets. See Chapter 2 MPLS Basic
Capability Configuration.
Step 2: Enable OSPF protocol at the interfaces connecting P router to PE router and
import direct-connect routes. See “OSPF” part in “Routing Protocol” for details.

3.3 Displaying and Debugging BGP/MPLS VPN

I. Displaying VPN address information from BGP table

After the above configuration, execute display command in any view to display the
running of the VPNv4 information in BGP database configuration, and to verify the
effect of the configuration.

Table 3-30 Display VPN address information from BGP table

Operation Command
display bgp vpnv4 { all | route-distinguisher
Display VPN address information
rd-value | vpn-instance vpn-instance-name }
from BGP table
{ group | network | peer | routing-table }

II. Displaying IP routing table associated with VPN-instance

After the above configuration, you can execute display command in any view to
display the corresponding information in the IP routing tables related to VPN-instance,
and to verify the effect of the configuration.

Table 3-31 Display IP routing table associated with VPN-instance

Operation Command
display ip routing-table vpn-instance
Display IP routing table
vpn-instance-name [ [ip-address ] [ verbose ] |
associated with VPN-instance
statistics ]

III. Displaying VPN-instance related information

After the above configuration, executing the display command in any view can display
the VPN-instance related information, including its RD, description, the interfaces
associated with it, and so on. You can view the information to verify the configuration
effect.

Huawei Technologies Proprietary

3-25
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Table 3-32 Display VPN-instance related information

Operation Command
Display the VPN-instance related
display ip vpn-instance
information, including its RD, description,
[ vpn-instance-name | verbose ]
the interfaces associated with it, and so on.

IV. Debugging information concerning processing BGP

Execute debugging command in user view for the debugging of the related
vpn-instance information.

Table 3-33 Enable the debugging for processing BGP

Operation Command
debugging bgp { all | event | normal | { keepalive |
Enable the debugging for
mp-update | open | packet | update | route-refresh |
processing BGP
update } [ receive | send |] [ verbose ] }
undo debugging bgp { {all | event | normal |
keepalive | mp-update | open | packet | update |
Disable the debugging
route-refresh } [ receive | send | verbose ] } { all |
event | normal | update }

V. Displaying MPLS L3VPN-LSP information

Table 3-34 Display MPLS L3VPN-LSP information

Operation Command
Display MPLS L3VPN
display mpls l3vpn-lsp [ verbose] include text
LSP information
Display MPLS L3VPN display mpls l3vpn-lsp [ vpn-instance
LSP VPN-instance vpn-instance-name ] [ transit | egress | ingress ]
information [include text | verbose ]

VI. Displaying Sham-link

Table 3-35 Display Sham-link

Operation Command
Display Sham-link display ospf [ process-id ] sham-link

Huawei Technologies Proprietary

3-26
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3.4 Typical BGP/MPLS VPN Configuration Example

3.4.1 Integrated BGP/MPLS VPN Configuration Example

I. Network requirements

z VPNA includes CE1 and CE3; VPNB includes CE2 and CE4.
z Subscribers in different VPNs cannot access each other. The VPN-target attribute
for VPNA is 111:1 and that for VPNB is 222:2.
z The PEs and P are Quidway switches supporting MPLS, and CEs are common
layer 3 switches.

Note:
The configuration in this case is focused on:
z Configure EBGP to exchange VPN routing information between CEs and PEs.
z Configure OSPF for inter-PE communication between PEs.
z Configure MP-IBGP to exchange VPN routing information between PEs.

II. Network diagram

AS 65410 AS 65430

CE1 CE3
VLAN201 VLAN201
168.1.1.1/16 168.3.1.1/16
AS 100
VPN-A VPN-A
PE1 PE3
RD(100:1) RD(100:3)
VLAN202 VLAN201 VLAN201 VLAN202
168.1.1.2/16 172.1.1.1/16 172.3.1.1/16 168.3.1.2/16
Loopback0 P Loopback0
202.100.1.1./32 VLAN301 VLAN303 202.100.1.3./32
VLAN302 VLAN304
PE2 PE4
RD(100:2) RD(100:4)
AS 65440
AS 65420 VLAN202 VLAN201 VLAN201 VLAN202
168.2.1.2/16 168.4.1.2/16
172.2.1.1./16 172.4.1.1./16
CE2 CE4
Loopback0 Loopback0
VLAN201 202.100.1.2./32 202.100.1.4./32 VLAN201
168.2.1.1/16 168.4.1.1/16
VPN-B VPN-B

Figure 3-8 Network diagram for integrated BGP/MPLS VPN

III. Configuration procedure

The following are the configuration introduction to PE, CE and P switches.

Huawei Technologies Proprietary

3-27
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

1) Configure CE1.
# Configure CE1 and PE1 as EBGP neighbors, import direct-connect routes and static
routes to import intra-CE1 VPN routes into BGP and advertise to PE1.CE1connects to
PE1 through interface Gigabitethernet 2/1/1.
[CE1] vlan 201
[CE1-vlan201] port gigabitethernet 2/1/1
[CE1-vlan201] quit
[CE1] interface Vlan-interface 201
[CE1-Vlan-interface201] ip address 168.1.1.1 255.255.0.0
[CE1-Vlan-interface201] quit
[CE1] bgp 65410
[CE1-bgp] group 168 external
[CE1-bgp] peer 168.1.1.2 group 168 as-number 100
[CE1-bgp] import-route direct
[CE1-bgp] import-route static

Note:
The configuration on the other three CE switches (CE2 to CE4) is similar to that on CE1,
the details are omitted here.

2) Configure PE1
# Configure vpn-instance for VPNA on PE1, as well as other associated attributes to
control advertisement of VPN routing information.
[PE1] ip vpn-instance vpna
[PE1-vpn-vpna] route-distinguisher 100:1
[PE1-vpn-vpna] vpn-target 111:1 both
[PE1-vpn-vpna] quit

# Configure PE1 and CE1 as MP-EBGP neighbors, import CE1 VPN routes learned
into MBGP VPN-instance address family.
[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpna
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 168 external
[PE1-bgp-af-vpn-instance] peer 168.1.1.1 group 168 as-number 65410
[PE1-bgp-af- vpn-instance] quit
[PE1-bgp] quit

Huawei Technologies Proprietary

3-28
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Bind the VLAN interface connecting PE1 and CE1 to the VPNA. Note that you should
first configure association between the VLAN interface and VPN-instance, and then
configure the IP address of the VLAN interface.
[PE1] vlan 202
[PE1-vlan202] port gigabitethernet 2/1/2
[PE1-vlan202] quit
[PE1] interface Vlan-interface 202
[PE1-Vlan-interface202] ip binding vpn-instance vpna
[PE1-Vlan-interface202] ip address 168.1.1.2 255.255.0.0
[PE1-Vlan-interface202] quit

# Configure Loopback interface. (For PE, the IP address for Loopback interface must
be a host address with 32-bit mask, to prevent the route is aggregated and then LSP
cannot process correctly interior-layer labels.)
[PE1] interface loopback0
[PE1-LoopBack 0] ip address 202.100.1.1 255.255.255.255
[PE1-LoopBack 0] quit

# Configure MPLS basic capacity and enable MPLS and LDP on VLAN interface
connecting PE1 and P. Create LSP and achieve MPLS packet forwarding.
[PE1] mpls lsr-id 202.100.1.1
[PE1] mpls
[PE1-mpls] quit
[PE1] mpls ldp
[PE1] vlan 201
[PE1-vlan201] port gigabitethernet 2/1/1
[PE1-vlan201] quit
[PE1] interface Vlan-interface 201
[PE1-Vlan-interface201] ip address 172.1.1.1 255.255.0.0
[PE1-Vlan-interface201] mpls
[PE1-Vlan-interface201] mpls ldp enable
[PE1-Vlan-interface201] quit

# Enable OSPF on the interface connecting PE1 and P and on the Loopback interface,
import direct-connect routes. Achieve inter-PE communication.
[PE1] ospf
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 172.1.0.0 0.0.255.255
[PE1-ospf-1-area-0.0.0.0] network 202.100.1.1 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] import-route direct
[PE1-ospf-1] quit

Huawei Technologies Proprietary

3-29
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE1] bgp 100
[PE1-bgp] group 202 internal
[PE1-bgp] peer 202.100.1.3 group 202
[PE1-bgp] peer 202.100.1.3 connect-interface loopback0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 202 enable
[PE1-bgp-af-vpn] peer 202.100.1.3 group 202
[PE1-bgp-af-vpn] quit
[PE1-bgp] quit
3) Configure P:
# Configure MPLS basic capacity, enable LDP on the interfaces connecting P and PE
for MPLS packet forwarding.
[P] mpls lsr-id 172.1.1.2
[P] mpls
[P-mpls] quit
[P] mpls ldp
[P] interface loopback0
[P-LoopBack 0] ip address 172.1.1.2 255.255.255.255
[P-LoopBack 0] quit
[P] vlan 301
[P-vlan301] port gigabitethernet 3/1/1
[P-vlan301] quit
[P] interface Vlan-interface 301
[P-Vlan-interface301] ip address 172.1.1.2 255.255.0.0
[P-Vlan-interface301] mpls
[P-Vlan-interface301] mpls ldp enable
[P-Vlan-interface301] quit
[P] vlan 302
[P-vlan302] port gigabitethernet 3/1/2
[P-vlan302] quit
[P] interface Vlan-interface 302
[P-Vlan-interface302] ip address 172.2.1.2 255.255.0.0
[P-Vlan-interface302] mpls
[P-Vlan-interface302] mpls ldp enable
[P-Vlan-interface302] quit
[P] vlan 303
[P-vlan303] port gigabitethernet 3/1/3
[P-vlan303] quit
[P] interface Vlan-interface 303
[P-Vlan-interface303] ip address 172.3.1.2 255.255.0.0

Huawei Technologies Proprietary

3-30
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[P-Vlan-interface303] mpls
[P-Vlan-interface303] mpls ldp enable
[P-Vlan-interface303] quit
[P] vlan 304
[P-vlan304] port gigabitethernet 3/1/4
[P-vlan304] quit
[P] interface Vlan-interface 304
[P-Vlan-interface304] ip address 172.4.1.2 255.255.0.0
[P-Vlan-interface304] mpls
[P-Vlan-interface304] mpls ldp enable
[P-Vlan-interface304] quit

# Enable OSPF protocol on the interfaces connecting P and PE, import direct-connect
route to achieve inter-PE communication.
[P] ospf
[P-ospf-1] area 0
[P-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.255.255
[P-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.255.255
[P-ospf-1-area-0.0.0.0] network 172.3.1.0 0.0.255.255
[P-ospf-1-area-0.0.0.0] network 172.4.1.0 0.0.255.255
[P-ospf-1-area-0.0.0.0] quit
[P-ospf-1] import-route direct
4) Configure PE3

Note:
The configuration on PE3 is similar to that on PE1, you should pay more attention to
VPN routing attribute setting on PE3 to get information about how to control
advertisement of a same VPN routing information (with same VPN-target) over MPLS
network.

# Create VPN-instance for VPNA on PE3, configure correlative attributes to control

advertisement of VPN routing information.
[PE3] ip vpn-instance vpna
[PE3-vpn-vpna] route-distinguisher 100:3
[PE3-vpn-vpna] vpn-target 111:1 both
[PE3-vpn-vpna] quit

# Set up MP-EBGP adjacency between PE3 and CE3, import intra-CE3 VPN routes
learned into MBGP VPN-instance address family.
[PE3] bgp 100
[PE3-bgp] ipv4-family vpn-instance vpna

Huawei Technologies Proprietary

3-31
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE3-bgp-af-vpn-instance] import-route direct

[PE3-bgp-af-vpn-instance] group 168 external
[PE3-bgp-af-vpn-instance] peer 168.3.1.1 group 168 as-number 65430
[PE3-bgp-af-vpn-instance] quit
[PE3-bgp] quit

# Bind the interface connecting PE3 and CE3 to VPNA.

[PE3] vlan 202
[PE3-vlan202] port gigabitethernet 2/1/2
[PE3-vlan202] quit
[PE3] interface Vlan-interface 202
[PE3-Vlan-interface202] ip binding vpn-instance vpna
[PE3-Vlan-interface202] ip address 168.3.1.2 255.255.0.0
[PE3-Vlan-interface202] quit

# Configure Loopback interface

[PE3] interface loopback0
[PE3-LoopBack 0] ip address 202.100.1.3 255.255.255.255
[PE3-LoopBack 0] quit

# Configure MPLS basic capacity and enable MPLS and LDP on VLAN interface
connecting PE3 and P. Creates LSP and achieve MPLS packet forwarding.
[PE3] mpls lsr-id 202.100.1.3
[PE3] mpls
[PE3-mpls] quit
[PE3] mpls ldp
[PE3] vlan 201
[PE3-vlan201] interface gigabitethernet 2/1/1
[PE3-vlan201] quit
[PE3] interface Vlan-interface 201
[PE3-Vlan-interface201] ip address 172.3.1.1 255.255.0.0
[PE3-Vlan-interface201] mpls
[PE3-Vlan-interface201] mpls ldp enable
[PE3-Vlan-interface201] quit

# Enable OSPF on the interface connecting PE3 and P and the Loopback interface,
import direct-connect routes.
[PE3] ospf
[PE3-ospf-1] area 0
[PE3-ospf-1-area-0.0.0.0] network 172.3.0.0 0.0.255.255
[PE3-ospf-1-area-0.0.0.0] network 202.100.1.3 0.0.0.0
PE3-ospf-1-area-0.0.0.0] quit
[PE3-ospf-1] import-route direct
[PE3-ospf-1-area-0.0.0.0] import-route direct

Huawei Technologies Proprietary

3-32
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information.
[PE3] bgp 100
[PE3-bgp] group 202 internal
[PE3-bgp] peer 202.100.1.1 group 202 as-number 100
[PE3-bgp] peer 202.100.1.1 connect-interface loopback0
[PE3-bgp] ipv4-family vpnv4
[PE3-bgp-af-vpn] peer 202 enable
[PE3-bgp-af-vpn] peer 202.100.1.1 group 202
[PE3-bgp-af-vpn] quit
5) Configure PE2 and PE4
The configuration of PE2 and PE4 is similar to that of PE1 and PE3. The details are
omitted here.

3.4.2 Extranet Configuration Example

I. Network requirements

Company A and Company B are located at City A and City B respectively. Their
headquarters is located at City C. They respectively own VPN1 and VPN2.
In this case, VPN function is provided by MPLS. There are some shared resources at
the City C for the two VPNs. All subscribers in both VPNs can access the shared
resources, but VPN subscribers in City A and City B cannot access each other.
The two companies cannot use identical IP addresses, for they share the same
VPN-instance at PE-C.

Note:
In the case the configuration is focused on controlling access authority of VPN
subscribers at different cities by configuring different VPN-target attributes at different
PEs.

Huawei Technologies Proprietary

3-33
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

II. Network diagram

SP network

AS100
PE-A PE-C PE-B
10.1.1.1 20.1.1.1 30.1.1.1
VLAN301 VLAN301
VLAN301
172.15.0.1/16 172.16.0.1/16
172.17.0.1/16
VLAN201 VLAN201 VLAN201
172.15.1.1/16 172.16.1.1/16 172.17.1.1/16
City A
CE-A City C City B CE-B
CE-C
AS65011 AS65012 AS65013
10.11.1.0/24 10.12.1.0/24

PC PC PC PC PC PC PC
VPN 1
VPN 2

Figure 3-9 Network diagram for Extranet

III. Configuration procedure

Note:
This configuration procedure has omitted configurations between PE and P, and
configurations on CEs. For these details refer to the former example.

1) Configure PE-A:
# Configure VPN-instance 1 for VPN1 on PE-A, so that it can send and receive VPN
routing information of VPN-target 111:1.
[PE-A] ip vpn-instance vpn-instance 1
[PE-A-vpn-1] route-distinguisher 100:1
[PE-A-vpn-1] vpn-target 111:1 both
[PE-A-vpn-1] quit

# Set up MP-EBGP adjacency between PE-A and CE-A, import intra-CE-A VPN routes
learned into MBGP VPN-instance address family.
[PE-A] bgp 100
[PE-A-bgp] ipv4-family vpn-instance vpn-instance1

Huawei Technologies Proprietary

3-34
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE-A-bgp-af-vpn-instance] import-route direct

[PE-A-bgp-af-vpn-instance] import-route static
[PE-A-bgp-af-vpn-instance] group 172 external
[PE-A-bgp-af-vpn-instance] peer 172.15.1.1 group 172 as-number 65011
[PE-A-bgp-af-vpn-instance] quit
[PE-A-bgp] quit

# Bind VPN-instance1 with the interface of VLAN301 which connects CE-A.

[PE-A] vlan 301
[PE-A-vlan301] port gigabitethernet 3/1/1
[PE-A-vlan301] quit
[PE-A] interface Vlan-interface 301
[PE-A-Vlan-interface301] ip binding vpn-instance vpn-instance1
[PE-A-Vlan-interface301] ip address 172.15.0.1 255.255.0.0
[PE-A-Vlan-interface301] quit

# Configure Loopback interface

[PE-A] interface loopback 0
[PE-A-LoopBack0] ip address 10.1.1.1 255.255.255.255
[PE-A-LoopBack0] quit

# Configure MPLS basic capacity.

[PE-A] mpls lsr-id 10.1.1.1
[PE-A] mpls
[PE-A-mpls] quit
[PE-A] mpls ldp

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE-A] bgp 100
[PE-A-bgp] group 20 internal
[PE-A-bgp] peer 20.1.1.1 group 20
[PE-A-bgp] peer 20.1.1.1 connect-interface loopback 0
[PE-A-bgp] ipv4-family vpnv4
[PE-A-bgp-af-vpn] peer 20 enable
[PE-A-bgp-af-vpn] peer 20.1.1.1 group 20
[PE-A-bgp-af-vpn] quit
2) Configure PE-C.
# Create a VPN-instance 2 on PE-C, so that it can send and receive VPN routing
information of VPN-target 111:1 and 222:2.
[PE-C] ip vpn-instance vpn-instance 2
[PE-C-vpn-2] route-distinguisher 100:2
[PE-C-vpn-2] vpn-target 111:1 both
[PE-C-vpn-2] vpn-target 222:2 both

Huawei Technologies Proprietary

3-35
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE-C-vpn-2] quit

# Set up MP-EBGP adjacency between PE-C and CE-C, import intra-CE-C VPN routes
learned into MBGP VPN-instance address family.
[PE-C] bgp 100
[PE-C-bgp] ipv4-family vpn-instance vpn-instance2
[PE-C-bgp-af-vpn-instance] import-route direct
[PE-C-bgp-af-vpn-instance] import-route static
[PE-C-bgp-af-vpn-instance] group 172 external
[PE-C-bgp-af-vpn-instance] peer 172.16.1.1 group 172 as-number 65012
[PE-C-bgp-af-vpn-instance] quit
[PE-C-bgp] quit

# Bind VPN-instance2 with the interface of VLAN301 which connects CE-C.

[PE-C] vlan 301
[PE-C-vlan301] port gigabitethernet 3/1/1
[PE-C-vlan301] quit
[PE-C] interface Vlan-interface 301
[PE-C-Vlan-interface301] ip binding vpn-instance vpn-instance2
[PE-C-Vlan-interface301] ip address 172.16.0.1 255.255.0.0
[PE-C-Vlan-interface301] quit

# Configure Loopback interface

[PE-C] interface loopback 0
[PE-C-LoopBack0] ip address 20.1.1.1 255.255.255.255
[PE-C-LoopBack0] quit

# Configure MPLS basic capacity.

[PE-C] mpls lsr-id 20.1.1.1
[PE-C] mpls
[PE-C-mpls] quit
[PE-C] mpls ldp

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE-C] bgp 100
[PE-C-bgp] group 10
[PE-C-bgp] peer 10.1.1.1 group 10
[PE-C-bgp] peer 10.1.1.1 connect-interface loopback 0
[PE-C-bgp] group 30
[PE-C-bgp] peer 30.1.1.1 group 30
[PE-C-bgp] peer 30.1.1.1 connect-interface loopback 0
[PE-C-bgp] ipv4-family vpnv4
[PE-C-bgp-af-vpn] peer 10 enable
[PE-C-bgp-af-vpn] peer 10.1.1.1 group 10

Huawei Technologies Proprietary

3-36
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE-C-bgp-af-vpn] peer 30 enable

[PE-C-bgp-af-vpn] peer 30.1.1.1 group 30
[PE-C-bgp-af-vpn] quit
3) Configure PE-B:
# Create VPN-instance 3 for VPN2 on PE-B, so that it can send and receive VPN
routing information of VPN-target 222:2.
[PE-B] ip vpn-instance vpn-instance 3
[PE-B-vpn-3] route-distinguisher 100:3
[PE-B-vpn-3] vpn-target 222:2 both
[PE-B-vpn-3] quit

# Set up MP-EBGP adjacency between PE-B and CE-B, import intra-CE-B VPN routes
learned into MBGP VPN-instance address family.
[PE-B] bgp 100
[PE-B-bgp] ipv4-family vpn-instance vpn-instance3
[PE-B-bgp-af-vpn-instance] import-route direct
[PE-B-bgp-af-vpn-instance] import-route static
[PE-B-bgp-af-vpn-instance] group 172 external
[PE-B-bgp-af-vpn-instance] peer 172.17.1.1 group 172 as-number 65013
[PE-B-bgp-af-vpn-instance] quit
[PE-B-bgp] quit

# Bind VPN-instance3 with the interface of VLAN301 which connects to CE-B.

[PE-B] vlan 301
[PE-B-vlan301] port gigabitethernet 3/1/1
[PE-B-vlan301] quit
[PE-B] interface Vlan-interface 301
[PE-B-Vlan-interface301] ip binding vpn-instance vpn-instance3
[PE-B-Vlan-interface301] ip address 172.17.0.1 255.255.0.0
[PE-B-Vlan-interface301] quit

# Configure Loopback interface

[PE-B] interface loopback 0
[PE-B-LoopBack0] ip address 30.1.1.1 255.255.255.255
[PE-B-LoopBack0] quit

# Configure MPLS basic capacity.

[PE-B] mpls lsr-id 30.1.1.1
[PE-B] mpls
[PE-B-mpls] quit
[PE-B] mpls ldp

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.

Huawei Technologies Proprietary

3-37
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE-B] bgp 100

[PE-B-bgp] group 20
[PE-B-bgp] peer 20.1.1.1 group 20
[PE-B-bgp] peer 20.1.1.1 connect-interface loopback 0
[PE-B-bgp] ipv4-family vpnv4
[PE-B-bgp-af-vpn] peer 20 enable
[PE-B-bgp-af-vpn] peer 20.1.1.1 group 20
[PE-B-bgp-af-vpn] quit

3.4.3 Hub&Spoke Configuration Example

I. Network requirements

Hub&Spoke networking is also called central server networking. The Site in the center
is called Hub-Site, while the one not in the center is called Spoke-Site. The Hub-Site
knows the routes to all other Sites in the same VPN, and the Spoke-Site must send its
traffic first to the Hub-Site and then to the destination. Hub-Site is the central node of
Spoke-Sites.
A bank has a headquarters network and subsidiary networks, and it requires that the
subsidiaries cannot directly exchange data with each other, but they can exchange data
through the headquarters network which provides uniform control. In this case,
Hub&Spoke networking topology is used: CE2 and CE3 are spoke-sites, while CE1 is a
hub-site in the bank data center. CE1 controls communication between CE2 and CE3.
z Set up IBGP adjacency between PE1 and PE2 or PE1 and PE3, but not between
PE2 and PE3, that is, VPN routing information cannot be exchanged between PE2
and PE3.
z Create two VPN-instances on PE1, import VPN routes of VPN-target 100:11 and
100:12, set VPN-target for VPN routes advertised as 100:2.
z Create a VPN-instance on PE2, import VPN routes of VPN-target 100:2, set
VPN-target for VPN routes advertised as 100:11.
z Create a VPN-instance on PE3, import VPN routes of VPN-target 100:2, set
VPN-target for VPN routes advertised as 100:12.
Then PE2 and PE3 can only learn their neighbor’s routes through PE1.

Huawei Technologies Proprietary

3-38
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Note:
In this case the configuration is focused on four points:
z Route advertisement can be controlled by VPN-target settings on different PEs.
z Routing loop is permitted only once, so that PE can receive route update messages
with AS number included from CE.
z In Hub&Spoke networking, VPN-target of VPN-instance (VPN-instance3) which is
used to release route on the PE1 cannot be the same with any VPN-target of
VPN-instance (VPN-instance2) which is used to import route on PE1.
z In Hub&Spoke networking, route-distinguisher rd2 (100:3) of VPN-instance which is
used to release route on the PE1 cannot be the same with the route-distinguisher
rd1 (100:1) or rd4 (100:4) of corresponding VPN-instances on each PE2 and PE3;
rd 1 and rd4 can be the same or not.

II. Network diagram

CE1
Hub Site

VLAN202 VLAN201
172.17.0.1/16 172.16.0.1/16
PE1

Loopback0
11.1.1.1/32

Internet
Spoke Site Spoke Site
PE3
CE2 PE2 20.1.1.2 CE3

VLAN201 VLAN201
172.15.0.1/16 Loopback0 Loopback0 172.18.0.1/16
22.1.1.1/32 33.1.1.1/32

Figure 3-10 Network diagram for Hub&Spoke

III. Configuration procedure

Huawei Technologies Proprietary

3-39
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Note:
The following contents are omitted in this case: MPLS basic capacity configuration
between PEs, configuration between PE and P, configuration between CEs. For the
details refer to 3.4.1 .

1) Configure PE1
# Configure two VPN-instances on PE1, set specified VPN-target for the routes
received from PE2 and PE3.
[PE1] ip vpn-instance vpn-instance2
[PE1-vpn-vpn-instance2] route-distinguisher 100:2
[PE1-vpn-vpn-instance2] vpn-target 100:11 import-extcommunity
[PE1-vpn-vpn-instance2] vpn-target 100:12 import-extcommunity
[PE1-vpn-instance2] quit
[PE1] ip vpn-instance vpn-instance3
[PE1-vpn-vpn-instance3] route-distinguisher 100:3
[PE1-vpn-vpn-instance3] vpn-target 100:2 export-extcommunity
[PE1-vpn-vpn-instance3] quit

# Set up EBGP adjacency between PE1 and CE1, import intra-CE1 VPN routes
learned into MBGP VPN-instance address family, with one routing loop permitted.
[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpn-instance2
[PE1-bgp-af-vpn-instance] import-route static
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 17216 external
[PE1-bgp-af-vpn-instance] peer 172.16.1.1 group 17216 as-number 65002
[PE1-bgp-af-vpn-instance] quit
[PE1-bgp] ipv4-family vpn-instance vpn-instance3
[PE1-bgp-af-vpn-instance] import-route static
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 17217 external
[PE1-bgp-af-vpn-instance] peer 172.17.1.1 group 17217 as-number 65002
[PE1-bgp-af-vpn-instance] peer 172.17.1.1 allow-as-loop 1
[PE1-bgp-af-vpn] quit
[PE1-bgp] quit

# Bind the VLAN interface connecting PE1 and CE1 to different VPN-instances. Bind
the interface of the VLAN to which the Ethernet port Gigabitethernet 2/1/1 belongs to
VPN-instance2, bind the interface of the VLAN to which the Ethernet port
Gigabitethernet 2/1/2 belongs to VPN-instance3.
[PE1] vlan 201

Huawei Technologies Proprietary

3-40
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-vlan201] port gigabitethernet 2/1/1

[PE1-vlan201] quit
[PE1] interface Vlan-interface 201
[PE1-Vlan-interface201] ip binding vpn-instance vpn-instance2
[PE1-Vlan-interface201] ip address 172.16.0.1 255.255.0.0
[PE1-Vlan-interface201] quit
[PE1] vlan 202
[PE1-vlan202] port gigabitethernet 2/1/2
[PE1-vlan202] quit
[PE1] interface Vlan-interface 202
[PE1-Vlan-interface202] ip binding vpn-instance vpn-instance3
[PE1-Vlan-interface202] ip address 172.17.0.1 255.255.0.0
[PE1-Vlan-interface202] quit

# Configure Loopback interface

[PE1] interface loopback 0
[PE1-LoopBack0] ip address 11.1.1.1 255.255.255.255
[PE1-LoopBack0] quit

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE1] bgp 100
[PE1-bgp] group 22
[PE1-bgp] peer 22.1.1.1 group 22 as-number 100
[PE1-bgp] peer 22.1.1.1 connect-interface loopback 0
[PE1-bgp] group 33
[PE1-bgp] peer 33.1.1.1 group 33 as-number 100
[PE1-bgp] peer 33.1.1.1 connect-interface loopback 0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 22 enable
[PE1-bgp-af-vpn] peer 22.1.1.1 group 22
[PE1-bgp-af-vpn] peer 33 enable
[PE1-bgp-af-vpn] peer 33.1.1.1 group 33
[PE1-bgp-af-vpn] quit
2) Configure PE2
# Create a VPN-instance on PE2, import VPN routing information of VPN-target 100:2
and advertise VPN routing information of VPN-target 100:1.
[PE2] ip vpn-instance vpn-instance1
[PE2-vpn-vpn-instance1] route-distinguisher 100:1
[PE2-vpn-vpn-instance1] vpn-target 100:11 export-extcommunity
[PE2-vpn-vpn-instance1] vpn-target 100:2 import-extcommunity
[PE2-vpn-vpn-instance1] quit

Huawei Technologies Proprietary

3-41
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Set up EBGP adjacency between PE2 and CE2, import intra-CE2 VPN routes
learned into MBGP VPN-instance address family.
[PE2] bgp 100
[PE2-bgp] ipv4-family vpn-instance vpn-instance1
[PE2-bgp-af-vpn-instance] import-route static
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] group 172 external
[PE2-bgp-af-vpn-instance] peer 172.15.1.1 group 172 as-number 65003
[PE2-bgp-af-vpn-instance] quit
[PE2-bgp] quit

# Bind the interface of the VLAN to which the port connecting PE2 and CE2 belongs to
VPN-instance.
[PE2] vlan 201
[PE2-vlan201] port gigabitethernet 2/1/1
[PE2-vlan201] quit
[PE2] interface Vlan-interface 201
[PE2-Vlan-interface201] ip binding vpn-instance vpn-instance1
[PE2-Vlan-interface201] ip address 172.15.0.1 255.255.0.0
[PE2-Vlan-interface201] quit

# Configure Loopback interface

[PE2] interface loopback 0
[PE2-LoopBack0] ip address 22.1.1.1 255.255.255.255
[PE2-LoopBack0] quit

# Set up MP-IBGP adjacency between PE2 and PE1 to exchange inter-PE VPN routing
information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE2] bgp 100
[PE2] group 11
[PE2-bgp] peer 11.1.1.1 group 11 as-number 100
[PE2-bgp] peer 11.1.1.1 connect-interface loopback 0
[PE2-bgp] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer 11 enable
[PE2-bgp-af-vpn] peer 11.1.1.1 allow-as-loop 1
[PE2-bgp-af-vpn] quit
[PE2-bgp] quit
3) Configure PE3
# Create a VPN-instance on PE3, import VPN routing information of VPN-target 100:2
and advertise VPN routing information of VPN-target 100:12.
[PE3] ip vpn-instance vpn-instance2
[PE3-vpn-vpn-instance2] route-distinguisher 100:4
[PE3-vpn-vpn-instance2] vpn-target 100:12 export-extcommunity

Huawei Technologies Proprietary

3-42
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE3-vpn-vpn-instance2] vpn-target 100:2 import-extcommunity

[PE3-vpn-vpn-instance2] quit

# Set up EBGP adjacency between PE3 and CE3 import intra-CE3 VPN routes learned
into MBGP VPN-instance address family.
[PE3] bgp 100
[PE3-bgp] ipv4-family vpn-instance vpn-instance2
[PE3-bgp-af-vpn-instance] import-route static
[PE3-bgp-af-vpn-instance] import-route direct
[PE3-bgp-af-vpn-instance] group 172 external
[PE3-bgp-af-vpn-instance] peer 172.18.1.1 group 172 as-number 65001
[PE3-bgp-af-vpn-instance] quit
[PE3-bgp] quit

# Bind the interface of the VLAN to which the port connecting PE3 and CE3 belongs to
VPN-instance.
[PE3] vlan 201
[PE3-vlan201] port gigabitethernet 2/1/1
[PE3-vlan201] quit
[PE3] interface Vlan-interface 201
[PE3-Vlan-interface201] ip binding vpn-instance vpn-instance2
[PE3-Vlan-interface201] ip address 172.18.0.1 255.255.0.0
[PE3-Vlan-interface201] quit

# Configure Loopback interface

[PE3] interface loopback 0
[PE3-LoopBack0] ip address 33.1.1.1 255.255.255.255
[PE3-LoopBack0] quit

# Set up MP-IBGP adjacency between PE3 and PE1 to exchange inter-PE VPN routing
information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE3] bgp 100
[PE3-bgp] group 11
[PE3-bgp] peer 11.1.1.1 group 11
[PE3-bgp] peer 11.1.1.1 connect-interface loopback 0
[PE3-bgp] ipv4-family vpnv4
[PE3-bgp-af-vpn] peer 11 enable
[PE2-bgp-af-vpn] peer 11.1.1.1 group 11
[PE2-bgp-af-vpn] peer 11.1.1.1 allow-as-loop 1
[PE3-bgp-af-vpn] quit
[PE3-bgp] quit

Huawei Technologies Proprietary

3-43
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3.4.4 CE Dual-home Configuration Example

I. Network requirements

For the applications which require high robustness of network, you may use CE
dual-home networking mode.
CE1 and CE2 are dual-homed; they are connected to both PE1 and PE2. Three PEs
are connected to each other so the links between them are backed up. CE3 and CE4
are single-homed; each of them is only connected to one PE.
CE1 and CE3 are in one VPN, and CE2 and CE4 are in another VPN. The two VPNs
cannot intercommunicate with each other.

II. Network diagram

AS:65003 AS:65004
CE3 CE4
VLAN211 VLAN211
192.168.13.2/24 192.168.23.2/24
Loopback0
3.3.3.3/32 VLAN314
VLAN311
192.168.13.1/24 192.168.23.1/24

VLAN312 VLAN313
30.1.1.1/24 20.1.1.2/24
PE3
VLAN214 VLAN214
30.1.1.2/24 AS:100 20.1.1.1/24
Loopback0 Loopback0
1.1.1.1/32 VLAN213 VLAN213
10.1.1.1/24 10.1.1.2/24 2.2.2.2/32
VLAN211 PE1 VLAN212 VLAN212 PE2 VLAN211
172.11.11.1/24 172.21.21.1/24 172.12.12.1/24 172.22.22.1/24

VLAN211 VLAN211
172.11.11.2/24 172.22.22.2/24
VLAN212 VLAN212
172.12.12.2/24 172.21.21.2/24

CE1 CE2
AS:65001 AS:65002

Figure 3-11 Network diagram for CE dual-home

Huawei Technologies Proprietary

3-44
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

III. Configuration procedure

Note:
The configuration of CE router is omitted in this case and you can refer to Section 3.4.1
Integrated BGP/MPLS VPN Configuration .

1) Configure PE1
# Configure two VPN-instances 1.1 and 1.2 respectively for CE1 and CE2 on PE1, set
different VPN-targets for them.
[PE1] ip vpn-instance vpn-instance1.1
[PE1-vpn-vpn-instance1.1] route-distinguisher 1.1.1.1:1
[PE1-vpn-vpn-instance1.1] vpn-target 1.1.1.1:1
[PE1-vpn-vpn-instance1.1] quit
[PE1] ip vpn-instance vpn-instance1.2
[PE1-vpn-vpn-instance1.2] route-distinguisher 2.2.2.2:2
[PE1-vpn-vpn-instance1.2] vpn-target 2.2.2.2:2
[PE1-vpn-vpn-instance1.2] quit

# Set up EBGP adjacency between PE1 and CE1 in VPN-instance 1, import intra-CE1
VPN routes learned into VPN-instance 1.1.
[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpn-instance1.1
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] import-route static
[PE1-bgp-af-vpn-instance] group 17211 external
[PE1-bgp-af-vpn-instance] peer 172.11.11.2 group 17211 as-number 65001
[PE1-bgp-af-vpn-instance] quit
[PE1-bgp] quit

# Set up EBGP adjacency between PE1 and CE2 in VPN-instance 1.2, import
intra-CE2 VPN routes learned into VPN-instance 1.2.
[PE1-bgp] ipv4-family vpn-instance vpn-instance1.2
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] import-route static
[PE1-bgp-af-vpn-instance] group 17221 external
[PE1-bgp-af-vpn-instance] peer 172.21.21.2 group 17221 as-number 65002
[PE1-bgp-af-vpn] quit
[PE1-bgp] quit

# Bind the interface connecting PE1 and CE1 to VPN-instance 1.1 and interface
connecting PE1 and CE2 to VPN-instance 1.2.

Huawei Technologies Proprietary

3-45
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1] vlan 211

[PE1-vlan211] port gigabitethernet 2/1/1
[PE1-vlan211] quit
[PE1] interface Vlan-interface 211
[PE1-Vlan-interface211] ip binding vpn-instance vpn-instance1.1
[PE1-Vlan-interface211] ip address 172.11.11.1 255.255.255.0
[PE1-Vlan-interface211] quit
[PE1] vlan 212
[PE1-vlan212] port gigabitethernet 2/1/2
[PE1-vlan212] quit
[PE1] interface Vlan-interface 212
[PE1-Vlan-interface212] ip binding vpn-instance vpn-instance1.2
[PE1-Vlan-interface212] ip address 172.21.21.1 255.255.255.0
[PE1-Vlan-interface212] quit

# Configure Loopback interface

[PE1] interface loopback 0
[PE1-LoopBack0] ip address 1.1.1.1 255.255.255.255
[PE1-LoopBack0] quit

# Configure MPLS basic capacity, enable LDP on the interface connecting PE1 and
PE2 and the interface connecting PE1 and PE3.
[PE1] mpls lsr-id 1.1.1.1
[PE1] mpls
[PE1-mpls] quit
[PE1] mpls ldp
[PE1] vlan 213
[PE1-vlan213] port gigabitethernet 2/1/3
[PE1-vlan213] quit
[PE1] interface Vlan-interface213
[PE1-Vlan-interface213] mpls
[PE1-Vlan-interface213] mpls ldp enable
[PE1-Vlan-interface213] mpls ldp transport-ip interface
[PE1-Vlan-interface213] ip address 10.1.1.1 255.255.255.0
[PE1-Vlan-interface213] quit
[PE1] vlan 214
[PE1-vlan214] port gigabitethernet 2/1/4
[PE1-vlan214] quit
[PE1] interface Vlan-interface 214
[PE1-Vlan-interface214] mpls
[PE1-Vlan-interface214] mpls ldp enable
[PE1-Vlan-interface214] mpls ldp transport-ip interface
[PE1-Vlan-interface214] ip address 30.1.1.2 255.255.255.0

Huawei Technologies Proprietary

3-46
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-Vlan-interface214] quit

# Enable OSPF on the interface connecting PE1 and PE2 and the interface connecting
PE1 and PE3 and the Loopback interface, to achieve inter-PE communication.
[PE1] Router-id 1.1.1.1
[PE1] ospf
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] network 30.1.1.2 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] network 10.1.1.1 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit

# Set up MP-IBGP adjacency between PEs to exchange inter-PE VPN routing

information and activate MP-IBGP peer in VPNv4 sub-address family view.
[PE1] bgp 100
[PE1-bgp] group 2
[PE1-bgp] peer 2.2.2.2 group 2
[PE1-bgp] peer 2.2.2.2 connect-interface loopback 0
[PE1-bgp] group 3
[PE1-bgp] peer 3.3.3.3 group 3
[PE1-bgp] peer 3.3.3.3 connect-interface loopback 0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 2 enable
[PE1-bgp-af-vpn] peer 2.2.2.2 group 2
[PE1-bgp-af-vpn] peer 3 enable
[PE1-bgp-af-vpn] peer 3.3.3.3 group 3
[PE1-bgp-af-vpn] quit
2) Configure PE2

Note:
The configuration of PE2 is similar to that of PE1, so only VPN-instance configuration is
detailed here.

# Create two VPN-instances 2.1 and 2.2 respectively for CE1 and CE2 on PE2,
configure different VPN-targets for them.
[PE2] ip vpn-instance vpn-instance2.1
[PE2-vpn-vpn-instance2.1] route-distinguisher 1.1.1.1:1
[PE2-vpn-vpn-instance2.1] vpn-target 1.1.1.1:1
[PE2-vpn-vpn-instance2.1] quit
[PE2] ip vpn-instance vpn-instance2.2

Huawei Technologies Proprietary

3-47
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE2-vpn-vpn-instance2.2] route-distinguisher 2.2.2.2:2

[PE2-vpn-vpn-instance2.2] vpn-target 2.2.2.2:2
[PE2-vpn-vpn-instance2.2] quit

# Set up EBGP adjacency between PE2 and CE1 in VPN-instance 2.1, import
intra-CE1 VPN routes learned into VPN-instance2.1.
[PE2] bgp 100
[PE2-bgp] ipv4-family vpn-instance vpn-instance2.1
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] import-route static
[PE2-bgp-af-vpn-instance] group 17212 external
[PE2-bgp-af-vpn-instance] peer 172.12.12.2 group 17212 as-number 65001
[PE2-bgp-af-vpn] quit

# Set up EBGP adjacency between PE2 and CE2 in VPN-instance2.2, import intra-CE2
VPN routes learned into VPN-instance2.2.
[PE2-bgp] ipv4-family vpn-instance vpn-instance2.2
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] import-route static
[PE2-bgp-af-vpn-instance] group 17222 external
[PE2-bgp-af-vpn-instance] peer 172.22.22.2 group 17222 as-number 65002
[PE2-bgp-af-vpn] quit
[PE2-bgp] quit

# Bind the interface connecting PE2 and CE1 to VPN-instance 2.1 and the interface
connecting PE2 and CE2 to VPN-instance 2.2.
[PE2] vlan 212
[PE2-vlan212] port gigabitethernet 2/1/2
[PE2-vlan212] quit
[PE2] interface Vlan-interface 212
[PE2-Vlan-interface212] ip binding vpn-instance vpn-instance2.1
[PE2-Vlan-interface212] ip address 172.12.12.1 255.255.255.0
[PE2-Vlan-interface212] quit
[PE2] vlan 211
[PE2-vlan211] port gigabitethernet 2/1/1
[PE2-vlan211] quit
[PE2] interface Vlan-interface 211
[PE2-Vlan-interface211] ip binding vpn-instance vpn-instance2.2
[PE2-Vlan-interface211] ip address 172.22.22.1 255.255.255.0
[PE2-Vlan-interface211] quit
3) Configure PE3

Huawei Technologies Proprietary

3-48
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

Note:
Only the VPN-instance configuration of PE3 is detailed here, other configurations are
similar to that of the PE1 and PE2, and are omitted here.

# Create two VPN-instances 3.1 and 3.2 respectively for CE3 and CE4 on PE3,
configure different VPN-targets for them.
[PE3] ip vpn-instance vpn-instance3.1
[PE3-vpn-vpn-instance3.1] route-distinguisher 1.1.1.1:1
[PE3-vpn-vpn-instance3.1] vpn-target 1.1.1.1:1
[PE3-vpn-vpn-instance3.1] quit
[PE3] ip vpn-instance vpn-instance3.2
[PE3-vpn-instance] route-distinguisher 2.2.2.2:2
[PE3-vpn-instance] vpn-target 2.2.2.2:2
[PE3-vpn-instance] quit

# Set up EBGP adjacency between PE3 and CE3 in VPN-instance3.1, import intra-CE3
VPN routes learned into VPN-instance3.1.
[PE3] bgp 100
[PE3-bgp] ipv4-family vpn-instance vpn-instance3.1
[PE3-bgp-af-vpn-instance] import-route direct
[PE3-bgp-af-vpn-instance] import-route static
[PE3-bgp-af-vpn-instance] group 192 external
[PE3-bgp-af-vpn-instance] peer 192.168.13.2 group 192 as-number 65003
[PE3-bgp-af-vpn-instance] quit
[PE3-bgp] quit

# Set up EBGP adjacency between PE3 and CE4 in VPN-instance3.2, import intra-CE4
VPN routes learned into VPN-instance3.2.
[PE3-bgp] ipv4-family vpn-instance vpn-instance3.2
[PE3-bgp-af-vpn-instance] import-route direct
[PE3-bgp-af-vpn-instance] import-route static
[PE3-bgp-af-vpn-instance] group 232 external
[PE3-bgp-af-vpn-instance] peer 192.168.23.2 group 232 as-number 65004
[PE3-bgp-af-vpn-instance] quit
[PE3-bgp] quit

# Bind the interface connecting PE3 and CE3 to VPN-instance3.1 and the interface
connecting PE3 and CE4 to VPN-instance 3.2.
[PE3] vlan 311
[PE3-vlan311] port gigabitethernet 3/1/1
[PE3-vlan311] quit
[PE3] interface Vlan-interface 311

Huawei Technologies Proprietary

3-49
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE3-Vlan-interface311] ip binding vpn-instance vpn-instance3.1

[PE3-Vlan-interface311] ip address 192.168.13.1 255.255.255.0
[PE3-Vlan-interface311] quit
[PE3] vlan 314
[PE3-vlan314] port gigabitethernet 3/1/4
[PE3-vlan314] quit
[PE3] interface Vlan-interface 314
[PE3-Vlan-interface314] ip binding vpn-instance vpn-instance3.2
[PE3-Vlan-interface314] ip address 192.168.23.1 255.255.255.0
[PE3-Vlan-interface314] quit

3.4.5 Cross-domain BGP/MPLS VPN Configuration Example

I. Network requirements

A VPN subscriber has sites in both city A and B. Because of the geographical reason,
site in City A accesses to the MPLS/VPN network of service provider in City A, and gets
AS100 as the AS number; site in City B accesses to the MPLS/VPN network of service
provider in City B, and gets AS200 as the AS number. The VPN goes through two ASs.
CE1 and CE2 belong to VPN-A, while CE3 and CE4 belong to VPN-B.

II. Network diagram

AS 100 AS 200

VLAN205 VLAN205 VLAN205 VLAN205

10.1.1.2/24 10.1.1.1/24 VLAN206 20.1.1.1/24 20.1.1.2/24
PE1:1.1.1.1/32 98.98.98.1/24 PE2:2.2.2.2/32
VLAN201 VLAN202 98.98.98.2/24 VLAN203 VLAN204
172.11.11.1/24 172.21.21.1/24 VLAN206 172.12.12.1/24 172.22.22.1/24
P1
P1:3.3.3.3/32 P2:4.4.4.4/32
VLAN201 VLAN201 VLAN201 VLAN201
172.11.11.2/24 172.21.21.2/24 172.12.12.2/24 172.22.22.2/24

CE1 CE3 CE2 CE4

PC1 PC3 PC2 PC4

192.168.11.10 192.168.21.10 192.168.12.10 192.168.22.10

Figure 3-12 Network diagram for ASBR

III. Configuration procedure

1) Configure PE1
# Enable MPLS and LDP.
[PE1] mpls lsr-id 1.1.1.1
[PE1] mpls
[PE1-mpls] quit
[PE1] mpls ldp

Huawei Technologies Proprietary

3-50
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Configure the VLAN interface connecting CE.

[PE1] vlan 201
[PE1-vlan201] port gigabitethernet 2/1/1
[PE1-vlan201] quit
[PE1] vlan 202
[PE1-vlan202] port gigabitethernet 2/1/2
[PE1-vlan202] quit

# Configure Loopback interface.

[PE1] interface loopback 0
[PE1-LoopBack0] ip address 1.1.1.1 255.255.255.255

# Configure VPN-instance.
[PE1] ip vpn-instance vpna
[PE1-vpn-vpna] route-distinguisher 100:1
[PE1-vpn-vpna] vpn-target 100:1 both
[PE1] ip vpn-instance vpnb
[PE1-vpn-vpnb] route-distinguisher 100:2
[PE1-vpn-vpnb] vpn-target 100:2 both

# Configure VLAN interface connecting PE1 and P1.

[PE1] vlan 205
[PE1-vlan205] port gigabitethernet 2/2/1
[PE1-vlan205] quit
[PE1] interface Vlan-interface 205
[PE1-Vlan-interface205] mpls
[PE1-Vlan-interface205] mpls ldp enable
[PE1-Vlan-interface205] ip address 10.1.1.2 255.255.255.0

# Bind the VLAN interface with the VPN-instance.

[PE1] interface Vlan-interface 201
[PE1-Vlan-interface201] ip binding vpn-instance vpna
[PE1-Vlan-interface201] ip address 172.11.11.1 255.255.255.0
[PE1-Vlan-interface201] quit
[PE1] interface Vlan-interface 202
[PE1-Vlan-interface202] ip binding vpn-instance vpnb
[PE1-Vlan-interface202] ip address 172.21.21.1 255.255.255.0
[PE1-Vlan-interface202] quit

# Enable EBGP between PE and CE.

[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpna
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 172-11 external
[PE1-bgp-af-vpn-instance] peer 172.11.11.2 group 172-11 as-number 65011

Huawei Technologies Proprietary

3-51
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-bgp- af-vpn] quit

[PE1-bgp] ipv4-family vpn-instance vpnb
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 172-21 external
[PE1-bgp-af-vpn-instance] peer 172.21.21.2 group 172-21 as-number 65021
[PE1-bgp-af-vpn-instance] peer 172.21.21.2 next-hop-local
[PE1-bgp-af-vpn-instace] quit

# Enable MP-IBGP between PE-ASBRs.

[PE1-bgp] group 3 internal
[PE1-bgp] peer 3.3.3.3 group 3
[PE1-bgp] peer 3.3.3.3 connect-interface loopback0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 3 enable
[PE1-bgp-af-vpn] peer 3.3.3.3 group 3
[PE1-bgp-af-vpn] quit
[PE1-bgp] quit
2) Configure PE2
# Configure MPLS.
[PE2] mpls lsr-id 2.2.2.2
[PE2] mpls
[PE2-mpls] quit
[PE2] mpls ldp

# Configure the VLAN interface connecting CE.

[PE2] vlan 203
[PE2-vlan203] port gigabitethernet 2/1/1
[PE2-vlan203] quit
[PE2] vlan 204
[PE2-vlan204] port gigabitethernet 2/1/2
[PE2-vlan204] quit

# Configure Loopback interface.

[PE2] interface loopback 0
[PE2-LoopBack0] ip address 2.2.2.2 255.255.255.255

# Configure VPN-instance.
[PE2] ip vpn-instance vpna
[PE2-vpn-vpna] route-distinguisher 200:1
[PE2-vpn-vpna] vpn-target 100:1 both
[PE2] ip vpn-instance vpnb
[PE2-vpn-vpnb] route-distinguisher 200:2
[PE2-vpn-vpnb] vpn-target 100:2 both

# Configure the VLAN interface connecting PE2 and P2.

Huawei Technologies Proprietary

3-52
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1] vlan 205

[PE1-vlan205] port gigabitethernet 2/2/1
[PE1-vlan205] quit
[PE1] interface Vlan-interface 205
[PE1-Vlan-interface205] mpls
[PE1-Vlan-interface205] mpls ldp enable
[PE1-Vlan-interface205] ip address 20.1.1.2 255.255.255.0

# Bind the VLAN interface with the VPN-instance.

[PE2] interface Vlan-interface 203
[PE2-Vlan-interface203] ip binding vpn-instance vpna
[PE2-Vlan-interface203] ip address 172.12.12.1 255.255.255.0
[PE2-Vlan-interface203] quit
[PE2] interface Vlan-interface 204
[PE2-Vlan-interface204] ip binding vpn-instance vpnb
[PE2-Vlan-interface204] ip address 172.22.22.1 255.255.255.0
[PE2-Vlan-interface204] quit

# Enable EBGP between PE and CE.

[PE2] bgp 200
[PE2-bgp] ipv4-family vpn-instance vpna
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] group 172-12 external
[PE2-bgp-af-vpn-instance] peer 172.12.12.2 group 172-12 as-number 65012
[PE2-bgp] ipv4-family vpn-instance vpnb
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] group 172-22 external
[PE2-bgp-af-vpn-instance] peer 172.22.22.2 group 172-22 as-number 65022
[PE2-bgp-af-vpn-instance] quit
[PE2] quit

# Enable MB-IBGP between PE-ASBRs

[PE2-bgp] group 4
[PE2-bgp] peer 4.4.4.4 group 4
[PE2-bgp] peer 4.4.4.4 connect-interface loopback0
[PE2-bgp] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer 4 enable
[PE2-bgp-af-vpn] peer 4.4.4.4 group 4
3) Configure P1 (P2 in similar way)
# Configure MPLS basic capability.
[P1] mpls lsr-id 3.3.3.3
[P1] mpls
[P1-mpls] quit

Huawei Technologies Proprietary

3-53
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[P1] mpls ldp

# Configure the interface Loopback 0.

[P1] interface loopback 0
[P1-LoopBack0] ip address 3.3.3.3 255.255.255.255

# Configure VLAN interface connecting PE1.

[P1] vlan 205
[P1-vlan205] port gigabitethernet 2/1/1
[P1-vlan205] quit
[P1] interface Vlan-interface 205
[P1-Vlan-interface205] mpls
[P1-Vlan-interface205] mpls ldp enable
[P1-Vlan-interface205] ip address 10.1.1.1 255.255.255.0
[P1-Vlan-interface205] quit

# Configure VLAN interface connecting PE2.

[P1] vlan 206
[P1-vlan206] port gigabitethernet 2/1/2
[P1-vlan206] quit
[P1] interface Vlan-interface 206
[P1-Vlan-interface206] mpls
[P1-Vlan-interface206] mpls ldp enable
[P1-Vlan-interface206] ip address 98.98.98.1 255.255.255.0
[P1-Vlan-interface206] quit

# Configure IBGP neighbors and EBGP neighbors.

[P1] bgp 100
[P1-bgp] group 1 internal
[P1-bgp] peer 1.1.1.1 group 1
[P1-bgp] peer 1.1.1.1 connect-interface loopback0
[P1-bgp] group 4 external
[P1-bgp] peer 98.98.98.2 group 4 as-number 200
[P1-bgp] ipv4-family vpnv4
[P1-bgp-af-vpn] peer 1 enable
[P1-bgp-af-vpn] peer 1.1.1.1 group 1
[P1-bgp-af-vpn] peer 1 next-hop-local
[P1-bgp-af-vpn] peer 98 enable
[P1-bgp-af-vpn] peer 98.98.98.2 group 98
[P1-bgp-af-vpn] undo policy vpn-target

Huawei Technologies Proprietary

3-54
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

3.4.6 Cross-Domain BGP/MPLS VPN Configuration Example — Option C

I. Network requirements

CE1 and CE2 belong to the same VPN. CE1 accesses the MPLS network through PE1
in AS100; and CE2 accesses the MPLS network through PE2 in AS200.
The example adopts Option C to implement a cross-domain BGP/MPLS VPN, that is,
the VPN routing is managed by the Multi-hop MP-EBGP which advertise label
VPN-IPv4 routes between PEs.

II. Network diagram

BGP/MPLS Backbo ne BGP/MPLS Backbo ne

AS 100 AS 200

Loop back0: Loop back0:

202.1 00. 1.1/ 32 202.2 00. 1.1/ 32
VLAN 210 :
VLAN 210
:
VLAN 110 :
VLAN 310
192.1 .1.1 /24 192.1 .1.2 /24
Loop back0: 172.1 .1.1 /16 162.1 .1.1 /16 Loop back0:
202.1 00. 1.2/ 32 200.2 00. 1.2/ 32
ASBR -PE1 ASBR-PE2
LSR I D:1 72.1 .1.1 LSR I D:1 62.1 .1.1
:
VLAN 110 :
VLAN 310
172.1 .1.2 /16 162.1 .1.2 /16
PE1 PE2
LSR I D: :
VLAN 510 LSR I D:
:
VLAN 410
172.1.1.2 168.2 .2.1 /16 162.1.1.2
168.1 .1.1 /16
VLAN 410 VLAN 510
168.1 .1.2 /16 168.2 .2.2 /16

CE1 CE2
AS 650 01 AS 650 02

Figure 3-13 Network diagram for Multihop EBGP cross-domain VPN

III. Configuration procedure

z Configuring OSPF on the MPLS backbone network

z Configuring basic MPLS capability on the MPLS backbone network
z Configuring a VPN instance on PEs.
z Configuring MP-BGP
1) Configure OSPF as the IGP protocol on the MPLS backbone network; making
OSPFs on PEs can learn routes from each other. Create OSPF neighbor between
ASBR-PE and PE in the same AS.
# Configure PE1.
[PE1] interface loopback0
[PE1-LoopBack0] ip address 202.100.1.2 255.255.255.255
[PE1-LoopBack0] quit
[PE1] vlan 110
[PE1-vlan110] interface vlan-interface 110
[PE1-Vlan-interface110] ip address 172.1.1.2 255.255.0.0
[PE1-Vlan-interface110] quit
[PE1] ospf

Huawei Technologies Proprietary

3-55
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 172.1.0.0 0.0.255.255
[PE1-ospf-1-area-0.0.0.0] network 202.100.1.2 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit

# Configure ASBR-PE1.
[ASBR-PE1] interface loopback0
[ASBR-PE1-LoopBack 0] ip address 202.100.1.1 255.255.255.255
[ASBR-PE1-LoopBack 0] quit
[ASBR-PE1] vlan 110
[ASBR-PE1-vlan110] interface vlan 110
[ASBR-PE1-Vlan-interface110] ip address 172.1.1.1 255.255.0.0
[ASBR-PE1-Vlan-interface110] quit
[ASBR-PE2] vlan 210
[ASBR-PE1-vlan210] interface vlan 210
[ASBR-PE1-Vlan-interface210] ip address 192.1.1.1 255.255.255.0
[ASBR-PE1-Vlan-interface210] quit
[ASBR-PE1] ospf
[ASBR-PE1-ospf-1] area 0
[ASBR-PE1-ospf-1-area-0.0.0.0] network 172.1.0.0 0.0.255.255
[ASBR-PE1-ospf-1-area-0.0.0.0] network 202.100.1.1 0.0.0.0
[ASBR-PE1-ospf-1-area-0.0.0.0] quit
[ASBR-PE1-ospf-1] quit

# Configure PE2.
[PE2] interface loopback0
[PE2-LoopBack0] ip address 202.200.1.2 255.255.255.255
[PE2-LoopBack0] quit
[PE2]vlan 310
[PE2-vlan310] interface vlan 310
[PE2-Vlan-interface310] ip address 162.1.1.2 255.255.0.0
[PE2- Vlan-interface310] quit
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 162.1.0.0 0.0.255.255
[PE2-ospf-1-area-0.0.0.0] network 202.200.1.2 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit

# Configure ASBR-PE2.
[ASBR-PE2] interface loopback0
[ASBR-PE2-LoopBack0] ip address 202.200.1.1 255.255.255.255
[ASBR-PE2-LoopBack0] quit

Huawei Technologies Proprietary

3-56
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[ASBR-PE2] interface vlan 310

[ASBR-PE2-Vlan-interface310] ip address 162.1.1.1 255.255.0.0
[ASBR-PE2-Vlan-interface310] quit
[ASBR-PE2] vlan 210
[ASBR-PE2-vlan210] interface vlan 210
[ASBR-PE2-Vlan-interface210] ip address 192.1.1.2 255.255.255.0
[ASBR-PE2-Vlan-interface210] quit
[ASBR-PE2] ospf
[ASBR-PE2-ospf-1] area 0
[ASBR-PE2-ospf-1-area-0.0.0.0] network 162.1.0.0 0.0.255.255
[ASBR-PE2-ospf-1-area-0.0.0.0] network 202.200.1.1 0.0.0.0
[ASBR-PE2-ospf-1-area-0.0.0.0] quit
[ASBR-PE2-ospf-1] quit
2) Configure basic MPLS capability on the MPLS backbone network to enable the
network to forward VPN traffic.

Note:
MPLS must be enabled between the ASBR-PEs.

# Configure basic MPLS capability on PE1 and enable LDP on the interface connected
to ASBR-PE1.
[PE1] mpls lsr-id 172.1.1.2
[PE1-mpls] lsp-trigger all
[PE1-mpls] quit
[PE1] mpls ldp
[PE1-mpls-ldp] quit
[PE1] interface vlan 110
[PE1-Vlan-interface110] mpls
[PE1-Vlan-interface110] mpls ldp
[PE1-Vlan-interface110] quit

# Configure basic MPLS capability on ASBR-PE1, enable LDP on the interface

connected to PE1, and enable MPLS on the interface connected to ASBR-PE2.
[ASBR-PE1] mpls lsr-id 172.1.1.1
[ASBR-PE1-mpls] lsp-trigger all
[ASBR-PE1-mpls] quit
[ASBR-PE1] mpls ldp
[ASBR-PE1-mpls-ldp] quit
[ASBR-PE1] interface vlan 110
[ASBR-PE1-Vlan-interface110] mpls

Huawei Technologies Proprietary

3-57
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[ASBR-PE1-Vlan-interface110] mpls ldp

[ASBR-PE1-Vlan-interface110] quit
[ASBR-PE1] interface vlan 210
[ASBR-PE1-Vlan-interface210] mpls
[ASBR-PE1-Vlan-interface210] quit

# Configure basic MPLS capability on ASBR-PE2, enable LDP on the interface

connected to PE2, and enable MPLS on the interface connected to ASBR-PE1.
[ASBR-PE2] mpls lsr-id 162.1.1.1
[ASBR-PE2-mpls] lsp-trigger all
[ASBR-PE2-mpls] quit
[ASBR-PE2] mpls ldp
[ASBR-PE2-mpls-ldp] quit
[ASBR-PE2] interface vlan 310
[ASBR-PE2-Vlan-interface310] mpls
[ASBR-PE2-Vlan-interface310] mpls ldp
[ASBR-PE2-Vlan-interface310] quit
[ASBR-PE2] interface vlan 210
[ASBR-PE2-Vlan-interface210] mpls
[ASBR-PE2-Vlan-interface310] quit

# Configure basic MPLS capability on PE2 and enable LDP on the interface connected
to ASBR-PE2.
[PE2] mpls lsr-id 162.1.1.2
[PE2-mpls] lsp-trigger all
[PE2-mpls] quit
[PE2] mpls ldp
[PE2-mpls-ldp] quit
[PE2] interface vlan 310
[PE2-Vlan-interface310] mpls
[PE2-Vlan-interface310] mpls ldp
[PE2-Vlan-interface310] quit
3) Create a VPN instance on each PE, and bind the instance to the interface
connected to the corresponding CE.
# Configure CE1
[CE1] vlan 410
[CE1-vlan410] interface vlan 410
[CE1-Vlan-interface410] ip address 168.1.1.2 255.255.0.0
[CE1-Vlan-interface410] quit

# Create a VPN instance on PE1 and bind it to the interface connected to CE1
[PE1] ip vpn-instance vpna
[PE1-vpn-vpna] route-distinguisher 100:2

Huawei Technologies Proprietary

3-58
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-vpn-vpna] vpn-target 100:1 both

[PE1-vpn-vpna] quit
[PE1]vlan 410
[PE1] interface vlan 410
[PE1-Vlan-interface410] ip binding vpn-instance vpna
[PE1-Vlan-interface410] ip address 168.1.1.1 255.255.0.0
[PE1-Vlan-interface410] quit

# Configure CE2
[CE2] vlan 510
[CE2-vlan510] interface vlan 510
[CE2-Vlan-interface510] ip address 168.2.2.2 255.255.0.0
[CE2-Vlan-interface510] quit

# Create a VPN instance on PE2 and bind it to the interface connected to CE2
[PE2] ip vpn-instance vpna
[PE2-vpn-instance] route-distinguisher 200:2
[PE2-vpn-instance] vpn-target 100:1 both
[PE2-vpn-instance] quit
[PE2] vlan 510
[PE2] interface vlan 510
[PE2-Vlan-interface510] ip binding vpn-instance vpna
[PE2-Vlan-interface510] ip address 168.2.2.1 255.255.0.0
[PE2-Vlan-interface510] quit
4) Configure MP-BGP, set up IBGP peer relation between PEs, and set up EBGP
peer relation between PEs and their CEs.

Note:
z Enable the exchanging of label-carried IPv4 route between the following routers:
PE1 and ASBR-PE1, PE2 and ASBR-PE2, ASBR-PE1 and ASBR-PE2.
z Make each ASBR-PE change the next hop to its own when it advertises routes to
the PE in the same AS.
z Configure routing policy on each ASBR-PE as follows: make the ASBR-PE assign
MPLS label when it advertises a route received from the PE in this AS to the
ASBR-PE in the peer AS, and let the ASBR-PE assign a new MPLS label when it
advertises a label-carried IPv4 route to the PE in this AS.

# Configure CE1
[CE1] bgp 65001
[CE1-bgp] group 20 external
[CE1-bgp] peer 168.1.1.1 group 20 as-number 100

Huawei Technologies Proprietary

3-59
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[CE1-bgp] quit

# Configure PE1: set up EBGP peer relation with CE1, IBGP peer relation with
ASBR-PE1, and Multihop MP-EBGP peer relation with PE2.
[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpna
[PE1-bgp-af-vpn-instance] group 10 external
[PE1-bgp-af-vpn-instance] peer 168.1.1.2 group 10 as-number 65001
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] quit
[PE1-bgp] group 20
[PE1-bgp] peer 20 label-route-capability
[PE1-bgp] peer 202.100.1.1 group 20
[PE1-bgp] peer 202.100.1.1 connect-interface loopback0
[PE1-bgp] group 30 external
[PE1-bgp] peer 30 ebgp-max-hop
[PE1-bgp] peer 200.200.1.2 group 30 as-number 200
[PE1-bgp] peer 200.200.1.2 connect-interface loopback0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 30 enable
[PE1-bgp-af-vpn] peer 200.200.1.2 group 30
[PE1-bgp-af-vpn] quit
[PE1-bgp] quit

# Configure ASBR-PE1: configure the route policy.

[ASBR-PE1] acl number 2001
[ASBR-PE1-acl-basic-2001] rule permit source 202.100.1.2 0
[ASBR-PE1-acl-basic-2001] rule deny source any
[ASBR-PE1-acl-basic-2001] quit
[ASBR-PE1] route-policy rtp-ebgp permit node 1
[ASBR-PE1-route-policy] if-match acl 2001
[ASBR-PE1-route-policy] apply mpls-label
[ASBR-PE1-route-policy] quit
[ASBR-PE1] route-policy rtp-ibgp permit node 10
[ASBR-PE1-route-policy] if-match mpls-label
[ASBR-PE1-route-policy] apply mpls-label
[ASBR-PE1-route-policy] quit

# Configure ASBR-PE1: set up EBGP peer relation with ASBR-PE2, and IBGP peer
relation with PE1.
[ASBR-PE1] bgp 100
[ASBR-PE1-bgp] import-route ospf
[ASBR-PE1-bgp] group 10 external
[ASBR-PE1-bgp] peer 10 label-route-capability

Huawei Technologies Proprietary

3-60
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[ASBR-PE1-bgp] peer 10 route-policy rtp-ebgp export

[ASBR-PE1-bgp] peer 192.1.1.2 group 10 as-number 200
[ASBR-PE1-bgp] group 20
[ASBR-PE1-bgp] peer 20 label-route-capability
[ASBR-PE1-bgp] peer 20 next-hop-local
[ASBR-PE1-bgp] peer 20 route-policy rtp-ibgp export
[ASBR-PE1-bgp] peer 202.100.1.2 group 20
[ASBR-PE1-bgp] peer 202.100.1.2 connect-interface loopback0
[ASBR-PE1-bgp] quit

# Configure CE2.
[CE2] bgp 65002
[CE2-bgp] group 10 external
[CE2-bgp] peer 168.2.2.1 group 10 as-number 200
[CE2-bgp] quit

# Configure PE2: set up EBGP peer relation with CE2, IBGP peer relation with
ASBR-PE2, and Multihop MP-EBGP peer relation with PE1.
[PE2] bgp 200
[PE2-bgp] ipv4-family vpn-instance vpna
[PE2-bgp-af-vpn-instance] group 10 external
[PE2-bgp-af-vpn-instance] peer 168.2.2.2 group 10 as-number 65002
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] quit
[PE2-bgp] group 20
[PE2-bgp] peer 20 label-route-capability
[PE2-bgp] peer 202.200.1.1 group 20
[PE2-bgp] peer 202.200.1.1 connect-interface loopback0
[PE2-bgp] group 30 external
[PE2-bgp] peer 30 ebgp-max-hop
[PE2-bgp] peer 202.100.1.2 group 30 as-number 100
[PE2-bgp] peer 202.100.1.2 connect-interface loopback0
[PE2-bgp] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer 30 enable
[PE2-bgp-af-vpn] peer 202.100.1.2 group 30
[PE2-bgp-af-vpn] quit
[PE2-bgp] quit

# Configure ASBR-PE2: configure the route policy.

[ASBR-PE2] acl number 2001
[ASBR-PE2-acl-basic-2001] rule permit source 200.200.1.2 0
[ASBR-PE2-acl-basic-2001] rule deny source any
[ASBR-PE2-acl-basic-2001] quit
[ASBR-PE2] route-policy rtp-ebgp permit node 1

Huawei Technologies Proprietary

3-61
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[ASBR-PE2-route-policy] if-match acl 2001

[ASBR-PE2-route-policy] apply mpls-label
[ASBR-PE2-route-policy] quit
[ASBR-PE2] route-policy rtp-ibgp permit node 10
[ASBR-PE2-route-policy] if-match mpls-label
[ASBR-PE2-route-policy] apply mpls-label
[ASBR-PE2-route-policy] quit

# Configure ASBR-PE2: set up EBGP peer relation with ASBR-PE1, and IBGP peer
relation with PE2.
[ASBR-PE2] bgp 200
[ASBR-PE2-bgp] import-route ospf
[ASBR-PE2-bgp] group 10 external
[ASBR-PE2-bgp] peer 10 label-route-capability
[ASBR-PE2-bgp] peer 10 route-policy rtp-ebgp export
[ASBR-PE2-bgp] peer 192.1.1.1 group 10 as-number 100
[ASBR-PE2-bgp] group 20
[ASBR-PE2-bgp] peer 20 label-route-capability
[ASBR-PE2-bgp] peer 20 next-hop-local
[ASBR-PE2-bgp] peer 20 route-policy rtp-ibgp export
[ASBR-PE2-bgp] peer 202.200.1.2 group 20
[ASBR-PE2-bgp] peer 202.200.1.2 connect-interface loopback0

3.4.7 Hierarchical BGP/MPLS VPN Configuration Example

I. Network requirements

For those VPNs that have distinct hierarchy, an MPLS VPN covering a province and its
cities, for example, incorporating the backbone network at the province level and the
networks at the city level into a single MPLS VPN will impose a high requirement in
performance on the equipment on the entire network, in the event that the network
topology size is large. However, the requirement in equipment performance can
become lower if this MPLS VPN is separated into two VPNs, the network at the
province level and the network at the city level, for example.
SPE acts as a PE on the network at the province level, and is connected with a
downstream MPLS VPN at the city level. UPE acts as a PE on the network at the city
level and provide access service for the VPN clients which are normally low-end
routers.

Huawei Technologies Proprietary

3-62
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

II. Network diagram

PE MPLS backbone
MPLS 骨干网 PE

Upper VPN
VLAN201
10. 0.0.1/8 Loopbac k0:10.0.0.2
SPE
VLAN301
10.0.0. 2/8
Loopbac k0:1.0.0.1

UPE
Lower VPN UPE

VPN1 Sit e1 VPN2 Sit e1 VPN1 Sit e1

VPN2 Sit e1

CE CE CE CE

Figure 3-14 Network diagram for hierarchical BGP/MPLS VPN

III. Configuration procedure

Note:
This case only illustrates the configurations concerned with PEs in a hierarchical
BGP/MPLS VPN.

1) Configure SPE
# Configure the basic MPLS capability.
[SPE] mpls lsr-id 1.0.0.2
[SPE] mpls
[SPE-mpls] quit
[SPE] mpls ldp

# Configure VPN-instance
[SPE] ip vpn-instance vpn1
[SPE-vpn-vpn1] route-distinguisher 100:1
[SPE-vpn-vpn1] vpn-target 100:1 both

# Configure interfaces (So far as a PE router concerned, its Loopback 0 interface must
be assigned with a host address of 32-bit mask.
[SPE] vlan 201
[SPE-vlan201] port gigabitethernet 2/1/1

Huawei Technologies Proprietary

3-63
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[SPE-vlan201] quit
[SPE] interface Vlan-interface 201
[SPE-Vlan-interface201] ip address 10.0.0.1 255.0.0.0
[SPE-Vlan-interface201] mpls
[SPE-Vlan-interface201] mpls ldp enable
[SPE-Vlan-interface201] quit
[SPE] interface loopback0
[SPE-LoopBack 0] ip address 1.0.0.2 255.255.255.255
[SPE-LoopBack 0] quit

# Configure BGP
[SPE] bgp 100
[SPE] import direct
[SPE-bgp] group 1 internal
[SPE-bgp] peer 1.0.0.1 group 1
[SPE-bgp] peer 1 connect-interface LoopBack0
[SPE-bgp] ipv4-family vpn-instance vpn1
[SPE--bgp-af-vpn-instance] import direct
[SPE--bgp-af-vpn-instance] quit
[SPE-bgp] ipv4-family vpnv4
[SPE-bgp-af-vpn] peer 1 enable
[SPE-bgp-af-vpn] peer 1.0.0.1 group 1
[SPE-bgp-af-vpn] peer 1.0.0.1 upe
[SPE-bgp-af-vpn] peer 1.0.0.1 default-route-advertise vpn-instance vpn1
[SPE-bgp-af-vpn] quit
[SPE-bgp] quit

# Configure OSPF
[SPE] ospf
[SPE] import-route direct
[SPE-ospf-1] area 0
[SPE-ospf-1-area-0.0.0.0] network 1.0.0.2 0.0.0.0
[SPE-ospf-1-area-0.0.0.0] network 10.0.0.0 0.255.255.255
2) Configure UPE
# Configure the basic MPLS capability.
[UPE] mpls lsr-id 1.0.0.1
[UPE] mpls
[UPE-mpls] quit
[UPE] mpls ldp

# Configure VPN-instance
[UPE] ip vpn-instance vpn1
[UPE-vpn-vpn1] route-distinguisher 100:1

Huawei Technologies Proprietary

3-64
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[UPE-vpn-vpn1] vpn-target 100:1 both

# Configure interfaces
[UPE] vlan 301
[UPE-vlan301] port gigabitethernet 2/2/1
[UPE-vlan301] quit
[UPE] interface Vlan-interface 301
[UPE-Vlan-interface301] mpls
[UPE-Vlan-interface301] mpls ldp enable
[UE1-Vlan-interface301] mpls ldp transport-ip interface
[UPE-Vlan-interface301] ip address 10.0.0.2 255.0.0.0
[UPE-Vlan-interface301] quit
[UPE] interface loopback0
[UPE-LoopBack 0] ip address 1.0.0.1 255.255.255.255

# Configure BGP
[UPE] bgp 100
[UPE-bgp] group 1 internal
[UPE-bgp] peer 1.0.0.2 group 1
[UPE-bgp] ipv4-family vpn-instance vpn1
[UPE--bgp-af-vpn-instance] import direct
[UPE-bgp] ipv4-family vpnv4
[UPE-bgp-af-vpn] peer 1 enable
[UPE-bgp-af-vpn] peer 1.0.0.2 group 1

# Configure OSPF
[UPE] ospf
[UPE-ospf-1] import-route direct
[UPE-ospf-1] area 0
[UPE-ospf-1-area-0.0.0.0] network 1.0.0.1 0.0.0.0
[UPE-ospf-1-area-0.0.0.0] network 10.0.0.2 0.255.255.255
[UPE-ospf-1-area-0.0.0.0] quit

3.4.8 OSPF Multi-instance Sham-link Configuration Example

I. Network requirements

As shown in the following picture, a company connects to a WAN through OSPF

multi-instance function of Quidway router. OSPF is bind to VPN1.MPLS VPN backbone
runs between PEs and OSPF runs between PE and CE. Configure a Sham-link
between PE1 and PE2 to ensure the traffic between CE1 and CE2 does not pass the
Backdoor link that directly connects CE1 and CE2.

Huawei Technologies Proprietary

3-65
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

II. Network diagram

LoopBack0: 1.1.1.1 LoopBack0: 3.3.3.3

CE1 VLAN202 PE3
PE1 1.1.1.1 VLAN202
3.3.3.3
10.10.10.10 168.1.13.1/24 168.1.13.2/24
VLAN201 VLAN201
10.1.1.1/24 10.1.1.2/24 LoopBack1: LoopBack1:
50.1.1.1 50.1.1.3
VLAN203
VLAN202 VLAN201
168.1.12.1/24
12.1.1.1/24 168.1.23.1/24

MPLS VPN Backbone

12.1.1.0/24 (backdoor) sham link (168.1.1.0/24)

VLAN202
VLAN203 VLAN202
12.1.1.2/24
168.1.12.2/24 168.1.23.2/24
20.2.1.0/24
VLAN201 VLAN201 LoopBack1:50.1.1.2
20.1.1.1/24 20.1.1.2/24 PE2
CE2
2.2.2.2
20.20.20.20
LoopBack0: 2.2.2.2

Figure 3-15 Network diagram for OSPF multi-instance

III. Configuration procedure

1) Configure PE1
# Enable MPLS and LDP.
[PE1] mpls lsr-id 50.1.1.1
[PE1] mpls
[PE1-mpls] quit
[PE1] mpls ldp

# Configure VPN-instance.
[PE1] ip vpn-instance vpn1
[PE1-vpn-vpn1] route-distinguisher 2:1
[PE1-vpn-vpn1] vpn-target 100:1 export-extcommunity
[PE1-vpn-vpn1] vpn-target 100:1 import-extcommunity

# Configure VLAN interface.

[PE1] vlan 203
[PE1-vlan203] port gigabitethernet 2/1/3
[PE1-vlan203] quit
[PE1] interface Vlan-interface 203
[PE1-Vlan-interface203] ip address 168.1.12.1 255.255.255.0
[PE1-Vlan-interface203] mpls
[PE1-Vlan-interface203] mpls ldp enable
[PE1-Vlan-interface203] quit
[PE1] vlan 201

Huawei Technologies Proprietary

3-66
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-vlan201] port gigabitethernet 2/1/1

[PE1-vlan201] quit
[PE1] interface Vlan-interface 201
[PE1-Vlan-interface201] ip binding vpn-instance vpn1
[PE1-Vlan-interface201] ip address 10.1.1.2 255.255.255.0
[PE1-Vlan-interface201] ospf cost 1
[PE1-Vlan-interface201] quit
[PE1] vlan 202
[PE1-vlan202] port gigabitethernet 2/1/2
[PE1-vlan202] quit
[PE1] interface Vlan-interface 202
[PE1-Vlan-interface202] ip address 168.1.13.1 255.255.255.0
[PE1-Vlan-interface202] ospf cost 1
[PE1-Vlan-interface202] mpls
[PE1-Vlan-interface202] mpls ldp enable
[PE1-Vlan-interface202] mpls ldp transport-ip interface
[PE1-Vlan-interface202] quit
[PE1] interface loopback0
[PE1-LoopBack0] ip binding vpn-instance vpn1
[PE1-LoopBack0] ip address 1.1.1.1 255.255.255.255
[PE1-LoopBack0] quit
[PE1] interface loopback1
[PE1-LoopBack1] ip address 50.1.1.1 255.255.255.255

# Configure BGP Peer.

[PE1] bgp 100
[PE1-bgp] undo synchronization
[PE1-bgp] group fc internal
[PE1-bgp] peer 50.1.1.2 group fc
[PE1-bgp] peer 50.1.1.2 connect-interface LoopBack1
[PE1-bgp] peer 50.1.1.3 group fc

# Configure BGP and import OSPF routing and direct-connect route.

[PE1-bgp] ipv4-family vpn-instance vpn1
[PE1-bgp-af-vpn-instance] import-route ospf 100
[PE1-bgp-af-vpn-instance] import-route ospf-ase 100
[PE1-bgp-af-vpn-instance] import-route ospf-nssa 100
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] undo synchronization

# Create and activate Peer in MBGP.

[PE1-bgp-af-vpn] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer fc enable
[PE1-bgp-af-vpn] peer fc advertise-community

Huawei Technologies Proprietary

3-67
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-bgp-af-vpn] peer 50.1.1.2 group fc

# Bind OSPF process to VPN-instance.

[PE1] ospf 100 router-id 1.1.1.1 vpn-instance vpn1
[PE1-ospf-100] import-route bgp
[PE1-ospf-100] area 0.0.0.0
[PE1-ospf-100-area-0.0.0.0] network 10.1.1.0 0.0.0.255

# Configuring Sham-link
[PE1-ospf-100-area-0.0.0.1] sham-link 1.1.1.1 2.2.2.2

# Configure the routes distributed to PE2 and PE3.

[PE1] ospf 1000
[PE1-ospf-1000] area 0
[Quidway-ospf-1000-area-0.0.0.0] network 168.12.1.0 0.0.0.255
[Quidway-ospf-1000-area-0.0.0.0] network 50.1.1.1 0.0.0.0
2) Configure PE2
# Enable MPLS and LDP.
[PE2] mpls lsr-id 50.1.1.2
[PE2] mpls
[PE2-mpls] quit
[PE2] mpls ldp

# Configure VPN-instance VPN1.

[PE2] ip vpn-instance vpn1
[PE2-vpn-vpn1] route-distinguisher 2:1
[PE2-vpn-vpn1] vpn-target 100:1 export-extcommunity
[PE2-vpn-vpn1] vpn-target 100:1 import-extcommunity

# Configure VLAN interface.

[PE2] vlan 203
[PE2-vlan203] port gigabitethernet 2/1/3
[PE2-vlan203] quit
[PE2] interface Vlan-interface 203
[PE2-Vlan-interface203] ip address 168.1.12.2 255.255.255.0
[PE2-Vlan-interface203] mpls
[PE2-Vlan-interface203] mpls ldp enable
[PE2-Vlan-interface203] quit
[PE2] vlan 201
[PE2-vlan201] port gigabitethernet 2/1/1
[PE2-vlan201] quit
[PE2] interface Vlan-interface 201
[PE2-Vlan-interface201] ip binding vpn-instance vpn1
[PE2-Vlan-interface201] ip address 20.1.1.2 255.255.255.0

Huawei Technologies Proprietary

3-68
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE2-Vlan-interface201] ospf cost 1

[PE2-Vlan-interface201] quit
[PE2] vlan 202
[PE2-vlan202] port gigabitethernet 2/1/2
[PE2-vlan202] quit
[PE2] interface Vlan-interface 202
[PE2-Vlan-interface202] ip address 168.1.23.2 255.255.255.0
[PE2-Vlan-interface202] ospf cost 1
[PE2-Vlan-interface202] mpls
[PE2-Vlan-interface202] mpls ldp enable
[PE2-Vlan-interface202] quit
[PE2] interface LoopBack0
[PE2-LoopBack0] ip binding vpn-instance vpn1
[PE2-LoopBack0] ip address 2.2.2.2 255.255.255.255
[PE2-LoopBack0] quit
[PE2] interface LoopBack1
[PE2-LoopBack1] ip address 50.1.1.2 255.255.255.255

# Configure BGP.
[PE2] bgp 100
[PE2-bgp] undo synchronization
[PE2-bgp] group fc internal
[PE2-bgp] peer 50.1.1.1 group fc
[PE2-bgp] peer 50.1.1.1 connect-interface LoopBack1
[PE2-bgp] peer 50.1.1.3 group fc

# Configure VPN-instance and import OSPF and direct-connect route.

[PE2-bgp] ipv4-family vpn-instance vpn1
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] import-route ospf-nssa 100
[PE2-bgp-af-vpn-instance] import-route ospf-ase 100
[PE2-bgp-af-vpn-instance] import-route ospf 100
[PE2-bgp-af-vpn-instance] undo synchronization

# Configure MBGP and enable Peer.

[PE2-bgp-af-vpn] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer fc enable
[PE2-bgp-af-vpn] peer fc advertise-community
[PE2-bgp-af-vpn] peer 50.1.1.1 group fc

# Configure OSPF and import BGP and direct-connect route.

[PE2] ospf 100 router-id 2.2.2.2 vpn-instance vpn1
[PE2-ospf-100] import-route bgp
[PE2-ospf-100] import-route static

Huawei Technologies Proprietary

3-69
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE2-ospf-100] area 0.0.0.0

[PE2-ospf-100-area-0.0.0.0] network 20.1.1.0 0.0.0.255

# Configuring Sham-link
[PE2-ospf-100-area-0.0.0.0] sham-link 2.2.2.2 1.1.1.1

# Configure static route to PE1 and PE3.

[PE2] ip route-static 50.1.1.1 255.255.255.255 168.1.12.1
[PE2] ip route-static 50.1.1.3 255.255.255.255 168.1.23.3

# Configure the routes distributed to PE1 and PE3.

[PE1] ospf 1000
[PE1-ospf-1000]area 0
[Quidway-ospf-1000-area-0.0.0.0] network 168.12.1.0 0.0.0.255
[Quidway-ospf-1000-area-0.0.0.0] network 50.1.1.1 0.0.0.0
3) Configure CE1.
# Configure interfaces
[CE1] vlan 202
[CE1-vlan202] port gigabitethernet 2/1/2
[CE1-vlan202] quit
[CE1] interface Vlan-interface 202
[CE1-Vlan-interface202] ip address 12.1.1.1 255.255.255.0
[CE1-Vlan-interface202] ospf cost 100
[CE1-Vlan-interface202] quit
[CE1] vlan 201
[CE1-vlan201] port gigabitethernet 2/1/1
[CE1-vlan201] quit
[CE1] interface Vlan-interface 201
[CE1-Vlan-interface201] ip address 10.1.1.1 255.255.255.0
[CE1-Vlan-interface201] ospf cost 1

# Configure OSPF.
[CE1] ospf 100 router-id 10.10.10.129
[CE1-ospf-100] import-route direct
[CE1-ospf-100] area 0.0.0.0
[CE1-ospf-100-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[CE1-ospf-100-area-0.0.0.0] network 12.1.1.0 0.0.0.255
4) Configure CE2
# Configure interface.
[CE2] vlan 202
[CE2-vlan202] port gigabitethernet 2/1/2
[CE2-vlan202] quit
[CE2] interface Vlan-interface 202

Huawei Technologies Proprietary

3-70
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[CE2-Vlan-interface202] ip address 12.1.1.2 255.255.255.0

[CE2-Vlan-interface202] ospf cost 100
[CE2-Vlan-interface202] quit
[CE2] vlan 201
[CE2-vlan201] port gigabitethernet 2/1/1
[CE2-vlan201] quit
[CE2] interface Vlan-interface 201
[CE2-Vlan-interface201] ip address 20.1.1.1 255.255.255.0
[CE2-Vlan-interface201] ospf cost 1

# Configure OSPF.
[CE2] ospf 100 router-id 20.20.20.20
[CE2-ospf-100] area 0.0.0.0
[CE2-ospf-100-area-0.0.0.0] network 12.1.1.0 0.0.0.255
[CE2-ospf-100-area-0.0.0.0] network 20.1.1.0 0.0.0.255

3.4.9 Nested BGP/MPLS VPN Configuration Example

I. Network requirements

A VPN user has multiple nodes to access the service provider's BGP/MPLS backbone
network. And this VPN is divided into three sub-VPNs: VPN1, VPN2 and VPN3.
Some of the nodes of these sub-VPNs directly access a PE in the network, and some
access a PE through the father VPN. That is, the adopted network structure is
unsymmetrical.
This example mainly describes the configuration of VPN1; the configuration of other
sub-VPNs is similar.

Huawei Technologies Proprietary

3-71
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

II. Network diagram

CE5
VLAN 210
18.1.1.2/8 AS100
VPN1 prov_pe1 prov_pe2
AS50003 5.5.5.5 4.4.4.4 CE6
VLAN 210
18.1.1.1/8
VLAN 110 VLAN 110 VPN2
10.1.1.1/8 10.1.1.2/8
CE7
VLAN 310 VLAN 410
1.1.1.2/8 2.1.1.2/8
VPN3
VLAN 310 VLAN 410
cust_pe1 cust_pe2
1.1.1.1/8 2.1.1.1/8
6.6.6.6 7.7.7.7
AS600 AS500
VLAN 510 VLAN 610
15.1.1.2/8 16.1.1.2/8

VLAN 510 CE3 VLAN 610 CE4

15.1.1.1/8 CE2 16.1.1.1/8
CE1

VPN1 VPN1 VPN3

VPN2
AS50001 AS50002

Figure 3-16 Network diagram for nested VPN

III. Configuration procedure

Note:
This procedure omits part of the configuration for CE router.

1) Configure IGP on the service provider's backbone network.

# Configure prov_pe1.
<Quidway> system-view
[Quidway] sysname prov_pe1
[prov_pe1] interface LoopBack0
[prov_pe1-LoopBack0] ip address 5.5.5.5 255.255.255.255
[prov_pe1-LoopBack0] quit
[prov_pe1] vlan 110
[prov_pe1-vlan110] interface vlan 110
[prov_pe1-Vlan-interface110] ip address 10.1.1.1 255.0.0.0
[prov_pe1-Vlan-interface110] quit
[prov_pe1] ospf
[prov_pe1-ospf] area 0
[prov_pe1-ospf-area-0.0.0.0] network 5.5.5.5 0.0.0.0
[prov_pe1-ospf-area-0.0.0.0] network 10.0.0.0 0.255.255.255

Huawei Technologies Proprietary

3-72
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Configure prov_pe2.
<Quidway> system-view
[Quidway] sysname prov_pe2
[prov_pe2] interface LoopBack0
[prov_pe2-LoopBack0] ip address 4.4.4.4 255.255.255.255
[prov_pe2-LoopBack0] quit
[prov_pe1] vlan 110
[prov_pe1-vlan110] interface vlan-interface 110
[prov_pe1-Vlan-interface110] ip address 10.1.1.2 255.0.0.0
[prov_pe1-Vlan-interface110] quit
[prov_pe2] ospf
[prov_pe2-ospf] area 0
[prov_pe2-ospf-area-0.0.0.0] network 4.4.4.4 0.0.0.0
[prov_pe2-ospf-area-0.0.0.0] network 10.0.0.0 0.255.255.255

Configure basic MPLS capability and MPLS LDP on the backbone network.
# Configure prov_pe1.
[prov_pe1] mpls lsr-id 5.5.5.5
[prov_pe1] mpls ldp
[prov_pe1] interface vlan 110
[prov_pe1- Vlan-interface110] mpls
[prov_pe1- Vlan-interface110] mpls ldp
[prov_pe1- Vlan-interface110] quit

# Configure prov_pe2.
[prov_pe2] mpls lsr-id 4.4.4.4
[prov_pe2] mpls ldp
[prov_pe2] interface vlan 110
[prov_pe2- Vlan-interface110] mpls
[prov_pe2- Vlan-interface110] mpls ldp
[prov_pe2- Vlan-interface110] quit

Configure IBGP between provider PEs.

# Configure prov_pe1.
[prov_pe1] bgp 100
[prov_pe1-bgp] group ibgp internal
[prov_pe1-bgp] peer 4.4.4.4 group ibgp
[prov_pe1-bgp] peer 4.4.4.4 connect-interface LoopBack0
[prov_pe1-bgp] ipv4-family vpnv4
[prov_pe1-bgp-af-vpn] peer ibgp enable
[prov_pe1-bgp-af-vpn] peer ibgp next-hop-local
[prov_pe1-bgp-af-vpn] peer 4.4.4.4 group ibgp
[prov_pe1-bgp-af-vpn] quit

Huawei Technologies Proprietary

3-73
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[prov_pe1-bgp] quit

# Configure prov_pe2.
[prov_pe2] bgp 100
[prov_pe2-bgp] group ibgp internal
[prov_pe2-bgp] peer 5.5.5.5 group ibgp
[prov_pe2-bgp] peer 5.5.5.5 connect-interface LoopBack0
[prov_pe2-bgp] ipv4-family vpnv4
[prov_pe2-bgp-af-vpn] peer ibgp enable
[prov_pe2-bgp-af-vpn] peer ibgp next-hop-local
[prov_pe2-bgp-af-vpn] peer 5.5.5.5 group ibgp
[prov_pe2-bgp-af-vpn] quit
[prov_pe2-bgp] quit
2) Create a VPN instance on provider PEs to access customer PEs and directly
connected user CEs.
# Configure prov_pe1.
[prov_pe1] ip vpn-instance customer_vpn
[prov_pe1-vpn-instance] route-distinguisher 3:3
[prov_pe1-vpn-instance] vpn-target 3:3 export-community
[prov_pe1-vpn-instance] quit
[prov_pe1] ip vpn-instance vpn1
[prov_pe1-vpn-instance] route-distinguisher 1:1
[prov_pe1-vpn-instance] vpn-target 1:1
[prov_pe1-vpn-instance] vpn-target 3:3
[prov_pe1-vpn-instance] quit
[prov_pe1] vlan 310
[prov_pe1] interface vlan 310
[prov_pe1-Vlan-interface310] ip binding vpn-instance customer_vpn
[prov_pe1-Vlan-interface310] ip address 1.1.1.2 255.0.0.0
[prov_pe1- Vlan-interface310] mpls
[prov_pe1- Vlan-interface310] quit
[prov_pe1] interface vlan 210
[prov_pe1-Vlan-interface210] ip binding vpn-instance vpn1
[prov_pe1- Vlan-interface210] ip address 18.1.1.1 255.0.0.0
[prov_pe1- Vlan-interface210] quit

# Configure prov_pe2.
[prov_pe2] ip vpn-instance customer_vpn
[prov_pe2-vpn-instance] route-distinguisher 3:3
[prov_pe2-vpn-instance] vpn-target 3:3
[prov_pe2-vpn-instance] quit
[prov_pe2] interface vlan 410
[prov_pe2-Vlan-interface410] ip binding vpn-instance customer_vpn

Huawei Technologies Proprietary

3-74
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[prov_pe2- Vlan-interface410] ip address 2.1.1.2 255.0.0.0

[prov_pe2- Vlan-interface410] mpls
[prov_pe2- Vlan-interface410] quit

# Configure cust_pe1.
<Quidway> system-view
[Quidway] sysname cust_pe1
[cust_pe1] interface LoopBack0
[cust_pe1-LoopBack0] ip address 6.6.6.6 255.255.255.255
[cust_pe1-LoopBack0] quit
[cust_pe1] mpls lsr-id 6.6.6.6
[cust_pe1] interface vlan 310
[cust_pe1-Vlan-interface310] ip address 1.1.1.1 255.0.0.0
[cust_pe1- Vlan-interface310] mpls
[cust_pe1- Vlan-interface310] quit

# Configure cust_pe2.
<Quidway> system-view
[Quidway] sysname cust_pe2
[cust_pe2] interface LoopBack0
[cust_pe2-LoopBack0] ip address 7.7.7.7 255.255.255.255
[cust_pe2-LoopBack0] quit
[cust_pe2] mpls lsr-id 7.7.7.7
[cust_pe2] interface vlan 410
[cust_pe2-Vlan-interface410] ip address 2.1.1.1 255.0.0.0
[cust_pe2-Vlan-interface410] mpls
[cust_pe2-Vlan-interface410] quit
3) Configure EBGP between provider PE and customer PE.
# Configure prov_pe1 to access the corresponding Customer PE.
[prov_pe1] route-policy comm permit node 10
[prov_pe1-route-policy-comm-10] if-match vpn-target 1:1
[prov_pe1-route-policy-comm-10] quit
[prov_pe1] bgp 100
[prov_pe1-bgp] ipv4-family vpn-instance customer_vpn
[prov_pe1-bgp-af-vpn-instance] group ebgp external
[prov_pe1-bgp-af-vpn-instance] undo peer ebgp enable
[prov_pe1-bgp-af-vpn-instance] peer 1.1.1.1 group ebgp as-number 600
[prov_pe1-bgp] ipv4-family vpnv4
[prov_pe1-bgp-af-vpn] nesting-vpn
[prov_pe1-bgp-af-vpn] peer ebgp vpn-instance customer_vpn enable
[prov_pe1-bgp-af-vpn] peer 1.1.1.1 vpn-instance customer_vpn group ebgp
[prov_pe1-bgp-af-vpn] peer 1.1.1.1 vpn-instance customer_vpn route-policy
comm import

Huawei Technologies Proprietary

3-75
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[prov_pe1-bgp-af-vpn] quit

# Configure prov_pe1 to access CE5

[prov_pe1-bgp] ipv4-family vpn-instance vpn1
[prov_pe1-bgp-af-vpn-instance] group ebgp external
[prov_pe1-bgp-af-vpn-instance] peer 18.1.1.2 group ebgp as-number 50003

# Configure prov_pe2 to access the corresponding Customer PE.

[prov_pe2] route-policy com2 permit node 10
[prov_pe2-route-policy-com2-10] if-match vpn-target 1:1
[prov_pe2-route-policy-com2-10] quit
[prov_pe2] bgp 100
[prov_pe2-bgp] ipv4-family vpn-instance customer_vpn
[prov_pe2-bgp-af-vpn-instance] group ebgp external
[prov_pe2-bgp-af-vpn-instance] undo peer ebgp enable
[prov_pe2-bgp-af-vpn-instance] peer 2.1.1.1 group ebgp as-number 500
[prov_pe2-bgp] ipv4-family vpnv4
[prov_pe2-bgp-af-vpn] nesting-vpn
[prov_pe2-bgp-af-vpn] peer ebgp vpn-instance customer_vpn enable
[prov_pe2-bgp-af-vpn] peer 2.1.1.1 vpn-instance customer_vpn group ebgp
[prov_pe2-bgp-af-vpn] peer 2.1.1.1 vpn-instance customer_vpn route-policy
com2 import

# Configure cust_pe1
[cust_pe1] bgp 600
[cust_pe1-bgp] group ebgp external
[cust_pe1-bgp] undo peer ebgp enable
[cust_pe1-bgp] peer 1.1.1.2 group ebgp as-number 100
[cust_pe1-bgp] ipv4-family vpnv4
[cust_pe1-bgp-af-vpn] peer ebgp enable
[cust_pe1-bgp-af-vpn] peer 1.1.1.2 group ebgp

# Configure cust_pe2
[cust_pe2] bgp 500
[cust_pe2-bgp] group ebgp external
[cust_pe2-bgp] undo peer ebgp enable
[cust_pe2-bgp] peer 2.1.1.2 group ebgp as-number 100
[cust_pe2-bgp] ipv4-family vpnv4
[cust_pe2-bgp-af-vpn] peer ebgp enable
[cust_pe2-bgp-af-vpn] peer 2.1.1.2 group ebgp
4) On each Customer PE, configure the sub-VPN that accesses the network through
the Customer PE.
# Configure cust_pe1.
[cust_pe1] ip vpn-instance vpn1

Huawei Technologies Proprietary

3-76
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[cust_pe1-vpn-instance] route-distinguisher 1:1

[cust_pe1-vpn-instance] vpn-target 1:1
[cust_pe1-vpn-instance] quit
[cust_pe1] interface vlan 510
[cust_pe1-Vlan-interface510] ip binding vpn-instance vpn1
[cust_pe1- Vlan-interface510] ip address 15.1.1.2 255.0.0.0
[cust_pe1-Vlan-interface510] quit
[cust_pe1] bgp 600
[cust_pe1-bgp] undo peer ebgp enable
[cust_pe1-bgp] ipv4-family vpn-instance vpn1
[cust_pe1-bgp-af-vpn-instance] group cegroup external
[cust_pe1-bgp-af-vpn-instance] peer 15.1.1.1 group cegroup as-number 50001
[cust_pe1-bgp-af-vpn-instance] quit
[cust_pe1-bgp] quit

# Configure cust_pe2
[cust_pe2] ip vpn-instance vpn1
[cust_pe2-vpn-instance] route-distinguisher 1:1
[cust_pe2-vpn-instance] vpn-target 1:1
[cust_pe2] interface vlan 610
[cust_pe2-Vlan-interface610] ip binding vpn-instance vpn1
[cust_pe2-Vlan-interface610] ip address 16.1.1.2 255.0.0.0
[cust_pe2-Vlan-interface510] quit
[cust_pe2] bgp 500
[cust_pe2-bgp] undo peer ebgp enable
[cust_pe2-bgp] ipv4-family vpn-instance vpn1
[cust_pe2-bgp-af-vpn-instance] group cegroup external
[cust_pe2-bgp-af-vpn-instance] peer 16.1.1.1 group cegroup as-number 50002
[cust_pe2-bgp-af-vpn-instance] quit
[cust_pe2-bgp] quit

3.4.10 OSPF Multi-instance CE Configuration Example

I. Network requirements

CE router in a VPN achieves service isolation by configuring multiple VPN instances.

Huawei Technologies Proprietary

3-77
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

II. Network diagram

vpn1
VLAN202
ospf 100 VLAN201
10.2.1.2/24
vpn1 10.1.1.2/24

MPLS Network
PE
vpn2
VLAN203 VLAN204
ospf 300
20.1.1.2/24 20.2.1.2/24
vpn2
Multi-VPN-Instance CE

Figure 3-17 Network diagram for OSPF multi-instance CE configuration

III. Configuration procedure

1) Configuring CE router
# Configure instance VPN1
[CE] ip vpn-instance vpn1
[CE-vpn-vpn1] route-distinguisher 100:1
[CE-vpn-vpn1] vpn-target 100:1 export-extcommunity
[CE-vpn-vpn1] vpn-target 100:1 import-extcommunity

# Configure instance VPN2

[CE] ip vpn-instance vpn2
[CE-vpn-vpn2] route-distinguisher 200:1
[CE-vpn-vpn2] vpn-target 200:1 export-extcommunity
[CE-vpn-vpn2] vpn-target 200:1 import-extcommunity

# Configure VLAN201.
[CE] vlan 201
[CE-vlan201] port gigabitethernet 2/1/1
[CE-vlan201] quit
[CE] interface Vlan-interface 201
[CE-Vlan-interface201] ip binding vpn-instance vpn1
[CE-Vlan-interface201] ip address 10.1.1.2 255.255.255.0

# Configure VLAN202.
[CE] vlan 202
[CE-vlan202] port gigabitethernet 2/1/2
[CE-vlan202] quit
[CE] interface Vlan-interface 202
[CE-Vlan-interface202] ip binding vpn-instance vpn1
[CE-Vlan-interface202] ip address 10.2.1.2 255.255.255.0
[CE-Vlan-interface202] ospf cost 100

# Configure VLAN203.

Huawei Technologies Proprietary

3-78
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[CE] vlan 203

[CE-vlan203] port gigabitethernet 2/1/3
[CE-vlan203] quit
[CE] interface Vlan-interface 203
[CE-Vlan-interface203] ip binding vpn-instance vpn2
[CE-Vlan-interface203] ip address 20.1.1.2 255.255.255.0

# Configure VLAN204.
[CE] vlan 204
[CE-vlan204] port gigabitethernet 2/1/4
[CE-vlan204] quit
[CE] interface Vlan-interface 204
[CE-Vlan-interface204] ip binding vpn-instance vpn2
[CE-Vlan-interface204] ip address 20.2.1.2 255.255.255.0

# Configure ospf 100.

[CE] ospf 100 vpn-instance vpn1
[CE-ospf-100] vpn-instance-capability simple
[CE-ospf-100] area 0.0.0.0
[CE-ospf-100-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[CE-ospf-100-area-0.0.0.0] network 10.2.1.0 0.0.0.255

# Configure OSPF 300.

[CE] ospf 300 vpn-instance vpn2
[CE-ospf-300] vpn-instance-capability simple
[CE-ospf-300] area 0.0.0.1
[CE-ospf-300-area-0.0.0.1] network 20.1.1.0 0.0.0.255
[CE-ospf-300-area-0.0.0.1] network 20.2.1.0 0.0.0.255

3.4.11 Multi-Role Host Configuration Example

I. Network requirements

CE1 and CE3 belong to VPN1, and CE2 belong to VPN2.

The host PC2 with the IP address of 172.16.0.1 accesses the network through CE2. As
a multi-role host, it can access both VPN1 and VPN2.

II. Network diagram

Huawei Technologies Proprietary

3-79
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

PC1
172.18.0.1/16

AS65410 Ethernet2/1/0
172.18.0.2/16
CE1

Ethernet1/1/0
20.2.1.1/24 AS100
Loopback0: Loopback0:
1.1.1.9/32 2.2.2.9/32
Ethernet3/1/0 Ethernet1/1/0
20.2.1.2/24 Ethernet1/1/0
192.168.1.2/24
192.168.1.1/24 PE2
PE1
Ethernet2/1/0
Ethernet1/1/0 Ethernet2/1/0 20.3.1.2/24 Ethernet1/1/0
20.1.1.1/24 20.1.1.2/24 20.3.1.1/24
CE2
CE3

Ethernet2/1/0 Ethernet2/1/0
AS65420 AS65430
172.16.0.2/16 172.19.0.2/
172.19.0.2/16

PC2 PC3
172.16.0.1/16 172.19.0.1/16

Figure 3-18 Network diagram for multi-role host application

III. Configuration procedure

1) Configure OSPF as the IGP protocol on the MPLS backbone network.

# Configure OSPF on PE1:
[PE1] interface loopback 0
[PE1-LoopBack0] ip address 1.1.1.9 32
[PE1-LoopBack0] quit
[PE1] vlan 110
[PE1-vlan110] interface vlan-interface 110
[PE1-Vlan-interface110] ip address 192.168.1.1 24
[PE1-Vlan-interface110] quit
[PE1] ospf
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit

# Configure OSPF on PE2:

[PE2] interface loopback 0
[PE2-LoopBack0] ip address 2.2.2.9 32

Huawei Technologies Proprietary

3-80
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE2-LoopBack0] quit
[PE2] vlan 110
[PE2-vlan110] interface vlan-interface 110
[PE1-Vlan-interface110] ip address 192.168.1.2 24
[PE2-Vlan-interface110] quit
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
2) Configure basic MPLS capability and create VPN instances.
# Configure basic MPLS capability on PE1:
[PE1] mpls lsr-id 1.1.1.9
[PE1-mpls] lsp-trigger all
[PE1-mpls] quit
[PE1] mpls ldp
[PE1-mpls-ldp] quit
[PE1] vlan 110
[PE1-vlan110] interface vlan-interface 110
[PE1-Vlan-interface110] mpls
[PE1-Vlan-interface110] mpls ldp
[PE1-Vlan-interface110] quit

# Create VPN instances for VPN1 and VPN2 on PE1, bind the address of the interface
of VLAN310 to VPN1 and VPN2.
[PE1] ip vpn-instance vpn1
[PE1-vpn-vpn1] route-distinguisher 100:1
[PE1-vpn-vpn1] vpn-target 100:1 both
[PE1-vpn-vpn1] quit
[PE1] ip vpn-instance vpn2
[PE1-vpn-vpn2] route-distinguisher 100:2
[PE1-vpn-vpn2] vpn-target 100:2 both
[PE1-vpn-vpn2] quit
[PE1] vlan 310
[PE1-vlan310] interface vlan-interface 310
[PE1-Vlan-interface310] ip binding vpn-instance vpn1
[PE1-Vlan-interface310] ip address 20.2.1.2 24
[PE1-Vlan-interface310] quit
[PE1] vlan 210
[PE1-vlan210] interface vlan-interface 210
[PE1-Vlan-interface210] ip binding vpn-instance vpn2

Huawei Technologies Proprietary

3-81
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE1-Vlan-interface210] ip address 20.1.1.2 24

[PE1-Vlan-interface210] quit

# Configure basic MPLS capability on PE2.

[PE2] mpls lsr-id 2.2.2.9
[PE2-mpls] lsp-trigger all
[PE2-mpls] quit
[PE2] mpls ldp
[PE2-mpls-ldp] quit
[PE2] vlan 110
[PE2-vlan110] interface vlan-interface 110
[PE2-Vlan-interface110] mpls
[PE2-Vlan-interface110] mpls ldp
[PE2-Vlan-interface110] quit

# Create a VPN instance for VPN1 on PE2, and bind the address of the interface of
VLAN210 to VPN1.
[PE2] ip vpn-instance vpn1
[PE2-vpn-vpn1] route-distinguisher 300:1
[PE2-vpn-vpn1] vpn-target 100:1 both
[PE2-vpn-vpn1] quit
[PE2] vlan 210
[PE2-vlan210] interface vlan-interface 210
[PE2-Vlan-interface210] ip binding vpn-instance vpn1
[PE2-Vlan-interface210] ip address 20.3.1.2 24
[PE2-Vlan-interface210] quit

Configure BGP.
# Configure CE1:
[CE1] vlan 310
[CE1-vlan310] interface vlan-interface 310
[CE1-Vlan-interface310] ip address 20.2.1.1 24
[CE1-Vlan-interface310] quit
[CE1] bgp 65410
[CE1-bgp] import-route direct
[CE1-bgp] group 10 external
[CE1-bgp] peer 20.2.1.2 group 10 as-number 100
[CE1-bgp] quit

# Configure CE2:
[CE2] vlan 210
[CE2-vlan210] interface vlan-interface 210
[CE2-Vlan-interface210] ip address 20.1.1.1 24
[CE2-Vlan-interface210] quit

Huawei Technologies Proprietary

3-82
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

# Configure CE3:
[CE3] vlan 210
[CE3-vlan210] interface vlan-interface 210
[CE3-Vlan-interface210] ip address 20.3.1.1 24
[CE3-Vlan-interface210] quit
[CE3] bgp 65430
[CE3-bgp] import-route direct
[CE3-bgp] group 10 external
[CE3-bgp] peer 20.3.1.2 group 10 as-number 100
[CE3-bgp] quit

# Configure PE1: Configure PE1 to be the IBGP peer of PE2 in BGP-VPNv4

sub-address family view. Configure PE1 to be the EBGP peer of CE1 in the BGP VPN1
instance view. Configure a static route between CE2 and PE1 to enable them to
communicate with each other. Import a static route in BGP VPN2 instance view to
advertise it to the remote PE.
[PE1] bgp 100
[PE1-bgp] group 10
[PE1-bgp] peer 2.2.2.9 group 10
[PE1-bgp] peer 2.2.2.9 connect-interface loopback 0
[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 10 enable
[PE1-bgp-af-vpn] peer 2.2.2.9 group 10
[PE1-bgp-af-vpn] quit
[PE1-bgp] ipv4-family vpn-instance vpn1
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] group 20 external
[PE1-bgp-af-vpn-instance] peer 20.2.1.1 group 20 as-number 65410
[PE1-bgp-af-vpn-instance] quit
[PE1-bgp] ipv4-family vpn-instance vpn2
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] import-route static

# Configure PE2: set up IBGP peer relation with PE1 in BGP-VPNv4 sub-address
family view; set up EBGP peer relation with CE3 in BGP-VPN instance view.
[PE2] bgp 100
[PE2-bgp] group 10
[PE2-bgp] peer 1.1.1.9 group 10
[PE2-bgp] peer 1.1.1.9 connect-interface loopback 0
[PE2-bgp] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer 10 enable
[PE2-bgp-af-vpn] peer 1.1.1.9 group 10
[PE2-bgp-af-vpn] quit

Huawei Technologies Proprietary

3-83
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

[PE2-bgp] ipv4-family vpn-instance vpn1

[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] group 20 external
[PE2-bgp-af-vpn-instance] peer 20.3.1.1 group 20 as-number 65430
[PE2-bgp-af-vpn-instance] quit
[PE2-bgp] quit

Configure multi-role host feature: If a routing protocol is employed between CE2 and
PE1, configure PE1 not to advertise any route information to CE2 to avoid route loops.
Following depicts a way to achieve this. You can also avoid route loops in other ways.
Directly configure a static route to PC2 on PE1 if no routing protocol is employed
between PE1 and CE2.
# Configure a default route pointing to PE1 on CE2.
[CE2] ip route-static 0.0.0.0 0.0.0.0 20.1.1.2

# Configure a multiple-role host route on PE1.

[PE1] ip route-static vpn-instance vpn1 172.16.0.0 16 vpn2 20.1.1.1

# Import the route of VPN1 to VPN2 using the RT attribute.

[PE1] ip vpn-instance vpn2
[PE1-vpn-vpn2] vpn-target 100:1 import-extcommunity

3.5 Troubleshooting
I. Symptom 1

In central server topology networking mode, the local end switch (spoke PE) cannot
learn the routing information of the peer end switch (spoke PE).
Solution:
z Check whether the BGP adjacent of spoke PE and hub PE is created correctly.
z Check whether the routing attributes import/export relation of each VPN-instance
is correct.
z Check from the hub PE that whether the routing information between two VPN
instances can be learnt by each other. if not, perform the following operation:
check if the EBGP protocol runs between hub PE and hub CE, check whether the
peer peer-address allow-as-loop command is configured between PE and CE.

II. Symptom 2

PE at the local end can learn private network route of the PE at peer end, but two PEs
cannot intercommunicate with each other.
Solution:
z Check whether the loopback interface configured on the PE has the address with
32-bit mask.

Huawei Technologies Proprietary

3-84
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 3 BGP/MPLS VPN Configuration

z Check whether the tag of private network route is correct.

z Check whether the LDP session is established using the display mpls ldp
session command.
z Check whether the LSP tunnel is established using the display mpls lsp
command.

III. Symptom 3

In Hub&Spoke networking mode, spoke PE cannot learn the private networking route of
Hub PE.
Solution:
z Check whether the LSP tunnel is established using the display mpls lsp
command.
z Check whether the BGP adjacent is established correctly.
z Check whether the routing import/export relation of the VPN-instance is correct.
z Check whether allow-as-loop is configured between spoke PE and hub PE.

IV. Symptom 4

Fall to specify the Loopback interface at the peer end as the BGP neighbor.
Solution:
z Check whether the local routing table has learnt the Loopback interface routing
information of the peer end using the display ip routing-table command.
z Check whether the address of the Loopback interface at the peer end can be
pinged using the ping command.
z Check whether the configuration information is correct using the display
current-configuration bgp command; confirm that you have specified the local
loopback interface as the interface to create adjacent interface with the peer end
by using the peer peer-address connect-interface command; confirm that you
have activate the neighbor in VPNv4 sub-address family view.
z Check whether the BGP information is correct on the PE at the peer end; check
whether specified the local Loopback interface as the interface to create adjacent
with the peer end; and check whether you have configured VPN capacity.

V. Symptom 5

During ASBR configuration, VPN route interior label does not switch on the ASBR.
Solution:
z Check whether the VPN neighbor is created correctly using the display bgp
vpnv4 all peer command.
z Check whether ASBR is configured with the undo policy vpn-target command. If
not, configure this command.

Huawei Technologies Proprietary

3-85
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Chapter 4 MPLS L2VPN

Note:
L2VPN mentioned in the following section refers to the L2VPN implemented through
virtual leased line (VLL).

4.1 MPLS L2VP Overview

4.1.1 Introduction to MPLS L2VP

MPLS L2VPN provides MPLS network-based Layer 2 VPN services. For users, an
MPLS L2VPN is a Layer 2 switched network, through which Layer 2 connections can
be established between network nodes.

CE
VPN A
VPN A PE VC
CE

PE
VC LSP
P
P
PE

VPN B
CE
CE
VPN B

Figure 4-1 MPLS L2VPN

MPLS L2VPN has the following advantages:

z Multiple network layer protocols supported, such as IP, IPv6, IPX, and SNA.
z Powerfulextensibility. MPLS L2VPN only establishes Layer 2 connections, rather
than imports and manages the routing information. This eases work load of PE
(provider edge) devices and the entire SP (service provider) network remarkably
and thus enables SPs to provide more VPNs and accommodate more users.

Huawei Technologies Proprietary

4-1
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

z Reliability and privacy of user routes. As no user routing information is imported,

there is no need for MPLS L2VPN to obtain and process the information, ensuring
the privacy of user routes.
Figure 4-2 illustrates the structure of an MPLS L2VPN packet.

Tunnel label
label VC label
label

Label Stack
Stack L2 PDU
PDU

Figure 4-2 Structure of an MPLS L2VPN packet

The fields in an MPLS L2VPN packet are described as follows:

Tunnel label (the outer label) is an MPLS label or a GRE label. It is used to transmit a
packet from one PE to anther.
VC label (the inner label) is a lower layer label used to identify the links between PEs
and CEs. Packets of MPLS L2VPNs implemented through circuit cross connect (CCC)
do not contain this label.
Data in MPLS L2VPN can be encapsulated as Ethernet or VLAN packets at the data
link layer. At present, data of different nodes in a VPN must be encapsulated as the
same type of packets.

4.1.2 Packet Forwarding

In an MPLS L2VPN, CE, PE, and P operate in the same way as those in a BGP/MPLS
VPN. That is, they also forward packets in an MPLS network transparently by using
label stacks. To forward packets in an MPLS L2VPN, tunnels must be established first
between PEs (this can be achieved by either manual configuration or signaling
protocols). When the interfaces connecting PEs and CEs are up, PEs insert VC labels
for packets sent by CE, and then mark them with tunnel labels. On receiving these
packets, the remote PEs strip off the tunnel labels and send the packets to the
corresponding CEs according to their VC labels.
Table 4-3 illustrates changes of the label stack of a packet during the forwarding.

Huawei Technologies Proprietary

4-2
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

CE1 PE1 P PE2

CE2

L2 PDU V L2 PDU L2 PDU

T V L2 PDU

L2 PDU: Data link layer packet

T: Tunnel label
V: VC label

Figure 4-3 Label stack processing of MPLS L2VPN

4.1.3 Implementation

At present, the official standard for MPLS L2VPN has not been established yet.
However, the PPVPN (Provider-provisioned Virtual Private Network) group of IETF
(Internet Engineering Task Force) defines multiple framework drafts, two of which are
commonly used. They are known as Martini draft and Kompella draft. Till May, 2005,
they are depicted in the following documents respectively:
draft-martini-l2circuit-trans-mpls-09.txt
draft-kompella-ppvpn-l2vpn-02.txt
Martini draft defines the way to implement MPLS L2VPN by establishing point-to-point
links. Here, LDP (Label Distribution Protocol) is used as the signaling protocol to
exchange VC labels. This kind of MPLS L2VPNs is known as Martini MPLS L2VPNs.
Kompella draft defines how to establish MPLS L2VPNs in MPLS networks through
end-to-end (CE-to-CE) connections. At present, BGP (border gateway protocol) is used
as the signaling protocol to propagate the information about Layer 2 reachability and
VC labels. This kind of MPLS L2VPNs is known as Kompella MPLS L2VPN.
Also, you can establish MPLS L2VPNs without signaling protocols. In this case, MPLS
L2VPN services are provided through statically configured VC labels. An example of
this is CCC, which implement MPLS L2VPNs through static configuration.
Table 4-1 describes the features and implementation ways of the above three types of
MPLS L2VPNs.

Huawei Technologies Proprietary

4-3
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Table 4-1 Features and implementation ways of the three types of MPLS L2VPNs

VPN type Implementation Feature

Data is transmitted
Configures static LSPs to implement through packets with
MPLS L2VPN. single-layer labels. LSPs
You must manually configure two LSPs are used exclusively.
(for sending and receiving packets No signaling is needed to
CCC respectively) for each CCC connection transmit the Layer 2 VPN
node by node (including PEs and Ps). information. Only MPLS
The configured LSPs can only be used forwarding is required. In
to transmit packets of the this way, CEs of different
corresponding CCC connections. SPs can be
interconnected easily.
Uses extended LDP as the signaling to
transmit the VC information.
Uses VC-TYPE and VC-ID to identify Local switching like CCC
VCs. VC-TYPE indicates the is not available.
Martini encapsulation type of data link layer,
and VC-ID uniquely identifies a VC. An LSP can be shared by
multiple VCs.
PEs connecting CEs exchange VC
labels through LDPs. They bind the
corresponding CEs through VC-IDs.

Users can assign extra

labels to VPNs for future
use. This eases the
configuration work loads
of VPN deployment and
capacity expansion.
Similar to Layer 3 BGP/MPLS VPN
VPN-target is used to
defined in RFC2547.
identify VPNs. This brings
PEs discover Layer 2 VPN nodes great flexibility for VPN
automatically through IBGP sessions networking.
established between them. They also
Connections between
propagate the VPN information.
CEs are not concerned.
Kompella Labels are distributed in the form of This type of MPLS
label blocks, which enables multiple L2VPN is implemented
connections being assigned tags by dividing the entrie SP
simultaneously. The size of a tag block network into different
is determined by CE Range VPNs and numbering
(user-configurable). these CEs in the VPNs.
VPN-target is used to differentiate To establish a connection
VPNs. between two CEs, you
need to set the local CE
ID and the remote CE ID
on the PE, and specify
the Circuit ID assigned for
the connection by the
local CE.

Huawei Technologies Proprietary

4-4
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Note:
You also can configure LSPs without P devices.

4.2 CCC MPLS L2VPN Configuration

4.2.1 Configuring CCC MPLS L2VPN

Table 4-2 Configure CCC MPLS L2VPN

Configuration
Command Description
step
Enter system view system-view —
Configure LASR ID mpls lsr-id X.X.X.X Required
Enable MPLS mpls Required

static-lsp egress
lsp-name l2vpn
Create the egress
incoming-interface
for the static LSP
vlan-interface vlan-id
in-label in-label Required. Before configuring a
CCC connection, you need to
static-lsp ingress
configure two static LSPs
Create the ingress lsp-name l2vpn nexthop
between the two PEs and all P
for the static LSP next-hop-addr out-label
routers in between for
out-label
bidirectional packets. Refer to
static-lsp transit corresponding sections in the
lsp-name l2vpn command manual for more
incoming-interface information about these
vlan-interface vlan-id commands and corresponding
Create the transit undo commands.
in-label in-label
for the static LSP
{ nexthop next-hop-addr
| outgoing-interface
vlan-interface vlan-id }
out-label out-label
Quit MPLS view
and enter system quit —
view
Enable MPLS
mpls l2vpn Required
L2VPN

Huawei Technologies Proprietary

4-5
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Configuration
Command Description
step

ccc Required. Two types of CCC

Establish local ccc-connection-name connections exist: local CCC
CCC connection interface vlan-interface connection and remote CCC
vlan-id out-interface connection. A local CCC
connection is established
between two local CEs. It can be
switched directly by the PE
ccc without being configured a static
ccc-connection-name LSP. A remote CCC connection
interface vlan-interface is established between the local
Establish remote
vlan-id transmit-lsp CE and a remote CE. The two
CCC connection
transmit-lsp-name CEs are attached to different
receive-lsp PEs. In this case, you need to
receive-lsp-name configure two static LSPs for
bidirectional packets transmitted
between the two PEs.

Caution:

z In L2VPN, you can configure only one virtual circuit for each VLAN interface.
z L2VPN supports VLAN interfaces only. When you configure an L2VPN on a VLAN
interface, data is encapsulated as Ethernet packets by default.
z You must use cards with the suffix CA (such as LSB2FT48CA) for the access sides
of CCC public/private network.
z You can configure only one VLAN on the access side of each VPN private network.
Each VLAN can have only one interface, and all the VLANs connecting to the
interface must have IGMP disabled.
z You must configure two static LSPs for each remote CCC connection. Two CCC
connections cannot share one static LSP.
z A static LSP used by a remote CCC connection cannot be used for other purposes
(such as carrying IP packets and BGP/MPLS VPN packets). When you configure a
static LSP for a CCC connection, the next hop must be the IP address from which
the ARP packets are learnt.

4.2.2 CCC MPLS L2VPN Configuration Example

I. Network requirements

CEs and the corresponding PEs shown in Figure 4-4 are interconnected through their
GigabitEthernet ports. Data is encapsulated as Ethernet packets at the data link layer. A
local connection is required between CE-A and CE-B, and a remote connection
between CE-A and CE-C.

Huawei Technologies Proprietary

4-6
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

II. Network diagram

CE B

Local connection

VLAN213
VLAN211 VLAN211
VLAN211 VLAN212
VLAN212 VLAN214
CE A P A
PE VLAN212
P PE B CE C
Remote connection

Figure 4-4 Network diagram for CCC MPLS L2VPN

III. Configuration procedure

1) Configure PE-A.
# Enable MPLS globally.
[Quidway] mpls lsr-id 1.1.1.1
[Quidway] mpls

# Enable MPLS L2VPN globally.

[Quidway] mpls l2vpn

# Configure VLAN 211.

[Quidway] vlan 211
[Quidway-vlan211] port gigabitethernet 2/1/1
[Quidway-Vlan211] interface vlan-interface 211
[Quidway-Vlan-interface211] quit

# Configure VLAN 212.

[Quidway] vlan 212
[Quidway-vlan212] port gigabitethernet 2/1/2
[Quidway-vlan212] interface vlan-interface 212
[Quidway-Vlan-interface212] quit

# Configure VLAN 213.

[Quidway] vlan 213
[Quidway-vlan213] port gigabitethernet 2/1/3
[Quidway-vlan213] interface vlan-interface 213
[Quidway-Vlan-interface213] quit

# Enable MPLS on the interface of VLAN 214.

[Quidway] vlan 214
[Quidway-vlan214] port gigabitethernet 2/1/4
[Quidway-vlan214] quit
[Quidway] interface vlan-interface 214

Huawei Technologies Proprietary

4-7
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-Vlan-interface214] ip address 5.5.5.1 24

[Quidway-Vlan-interface214] mpls
[Quidway-Vlan-interface214] quit

# Configure the local connection.

[Quidway] ccc local-conn interface vlan-interface 211 outgoing-interface
vlan-interface 213

# Configure a static LSP, with the out-label of 100 and the egress interface being the
interface of VLAN 214.
[Quidway] mpls
[Quidway-mpls] static-lsp ingress PEA-PEB l2vpn nexthop 5.5.5.2 out-label 100

# Configure a static LSP, with the in-label of 211 and the ingress interface being the
interface of VLAN 214.
[Quidway-mpls] static-lsp egress PEB-PEA l2vpn incoming-interface
vlan-interface 214 in-label 211

# Configure the remote connection.

[Quidway] ccc remote-connection interface vlan-interface 212 transmit-lsp
PEA-PEB receive-lsp PEB-PEA
2) Configure PE-B.
# Enable MPLS globally.
[Quidway] mpls lsr-id 10.0.0.1
[Quidway] mpls

# Enable MPLS L2VPN globally.

[Quidway] mpls l2vpn

# Configure VLAN 211.

[Quidway] vlan 211
[Quidway-vlan211] port gigabitethernet 2/1/1
[Quidway] interface vlan-interface 211
[Quidway-Vlan-interface211] quit

# Enable MPLS on the interface of VLAN 212.

[Quidway] vlan 212
[Quidway-vlan212] port gigabitethernet 2/1/2
[Quidway-vlan212] quit
[Quidway] interface Vlan-interface 212
[Quidway-Vlan-interface212] ip address 6.6.6.1 24
[Quidway-Vlan-interface212] mpls

# Configure a static LSP, with the out-label of 200 and the egress interface being the
interface of VLAN 212.
[Quidway-mpls] static-lsp ingress nexthop 6.6.6.2 out-label 200

Huawei Technologies Proprietary

4-8
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

# Configure a static LSP, with the in-label of 101 and the ingress interface being the
interface of VLAN 212.
[Quidway-mpls] static-lsp egress PEA-PEB l2vpn incoming-interface
vlan-interface 212 in-label 101

# Configure the remote connection.

[Quidway] ccc remote-connection interface vlan-interface 211 transmit-lsp
PEB-PEA receive-lsp PEA-PEB
3) Configure P.
[Quidway] mpls lsr-id 10.0.0.2
[Quidway] mpls
[Quidway] vlan 211
[Quidway-vlan211] port gigabitethernet 2/1/1
[Quidway-vlan211] quit
[Quidway] interface Vlan-interface 211
[Quidway-Vlan-interface211] ip address 5.5.5.2 24
[Quidway-Vlan-interface211] mpls
[Quidway] vlan 212
[Quidway-vlan212] port gigabitethernet 2/1/2
[Quidway-vlan212] quit
[Quidway] interface Vlan-interface 212
[Quidway-Vlan-interface212] ip address 6.6.6.2 24
[Quidway-Vlan-interface212] mpls

# Configure a static LSP, with the in-label of 100, the ingress interface being the
interface of VLAN 211, the out-label of 101, and the egress interface being the interface
of VLAN 212.
[Quidway-mpls] static-lsp transit PEA-PEB l2vpn incoming-interface
vlan-interface 211 in-label 100 nexthop 6.6.6.1 vlan-interface 212 out-label
101

# Configure a static LSP, with the in-label of 200, the ingress interface being the
interface of VLAN 212, the out-label of 211, and the egress interface being the interface
of VLAN 211.
[Quidway-mpls] static-lsp transit PEB-PEA l2vpn incoming-interface
vlan-interface 212 in-label 200 nexthop 5.5.5.1 out-label 211

Huawei Technologies Proprietary

4-9
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Caution:

Following must be met to make a local CCC connection to go up:

z The interfaces of the two CE are physically up.
z The encapsulation types of the interfaces of the two CEs are the same and are
supported by the MPLS L2VPN.
For Layer 2 connections with the MPLS L2VPN being VLAN encapsulation, the VLAN
IDs of the interfaces of the two CEs can either be the same or different. However, if a
trunk is configured between the CEs and the PEs on both sides, the VLAN IDs of the
interfaces of the two CEs must be the same.

4.3 Martini MPLS L2VPN Configuration

4.3.1 Configuring Martini MPLS L2VPN

Table 4-3 Configure Martini MPLS L2VPN

Configuration
Command Description
step
Enter system view system-view —
Configure the LSR
mpls lsr-id X.X.X.X Required
ID
Enable MPLS mpls Required

Quit to system view quit —

Required. Before configuring
the connection, you need to
enable LDP on each router
and each port of the public
Configure the LDP network along the connection
mpls ldp remote-peer index
remote peer and configure the LDP
remote peer on the peer PE.
Refer to LDP Configuration in
MPLS module for the
configuration related to LDP .
Quit to system view quit —

Enter VLAN interface vlan-interface

—
interface view vlan id
Enable MPLS
mpls l2vpn Required
L2VPN

Huawei Technologies Proprietary

4-10
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Configuration
Command Description
step
Required. To configure a
Martini MPLS L2VPN on a
Create a Martini PE, you need to provide the
MPLS L2VPN IP address (Lsr-id) of the
virtual connection mpls l2vc ip-address vc-id peer PE and specify the VC
in VLAN interface ID. The combination of the
view VC ID and the encapsulation
type must be unique on the
PE.
Quit to system view quit —

Caution:

z You must use cards with the suffix CA (such as LSB2FT48CA) on the public/private
network access sides when configuring Martini MPLS L2VPN.
z You can configure only one VLAN on the access side of each VPN private network.
Each VLAN can have only one interface. And all the VLANs connecting to the
interface must have IGMP disabled.
z L2VPN supports VLAN interfaces only. When you configure an L2VPN on a VLAN
interface, data is encapsulated as Ethernet packets by default.

4.3.2 Martini MPLS L2VPN Configuration Example

I. Network requirements

CEs shown in Figure 4-5 are in the same VLAN as the corresponding PEs resides in. A
remote connection is required between CE-A and CE-B.

II. Network diagram

VLAN211
VLAN211 VLAN212

CE A VLAN212 PE A VLAN211 P VLAN212 PE B CE B

Figure 4-5 Network diagram for Martini MPLS L2VPN

III. Configuration procedure

1) Configure PE-A.
# Configure the LSR ID. Enable MPLS, LDP, and MPLS L2VPN.
[Quidway-A] mpls lsr-id 192.1.1.1
[Quidway-A] mpls

Huawei Technologies Proprietary

4-11
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-A-mpls] quit
[Quidway-A] mpls ldp
[Quidway-A] mpls l2vpn

# Configure VLAN 212.

[Quidway-A] vlan 212
[Quidway-A-vlan212] port gigabitethernet 2/1/2
[Quidway-A-vlan212]interface vlan-interface 212
[Quidway-Vlan-interface212] quit

# Configure the VLAN interface.

[Quidway-A] vlan 211
[Quidway-A-vlan211] port gigabitethernet 2/1/1
[Quidway-A-vlan211] quit
[Quidway-A] interface Vlan-interface 211
[Quidway-A-Vlan-interface211] ip address 168.1.1.1 255.255.0.0
[Quidway-A-Vlan-interface211] mpls
[Quidway-A-Vlan-interface211] mpls ldp enable

# Configure an IP address for the Loopback interface, which is used as the Router ID.
[Quidway-A] interface loopback 0
[Quidway-A-LoopBack0] ip address 192.1.1.1 255.255.255.255

# Enable OSPF.
[Quidway-A] ospf 1
[Quidway-A-ospf-1] area 0.0.0.0
[Quidway-A-ospf-1-area-0.0.0.0] network 192.1.1.1 0.0.0.0
[Quidway-A-ospf-1-area-0.0.0.0] network 168.1.1.1 0.0.255.255

# Create an LSP tunnel.

[Quidway-A] mpls ldp

# Configure the LDP Remote Peer.

[Quidway-A] mpls ldp remote-peer 1
[Quidway-A-remote-peer-1] remote-ip 192.1.1.2

# Configure a Martini MPLS L2VPN connection.

[Quidway-A] interface vlan-interface 212
[Quidway-A-Vlan-interface212] mpls l2vc 192.1.1.2 20
2) Configure PE-B.
# Configure the LSR ID. Enable MPLS, LDP, and MPLS L2VPN.
[Quidway-B] mpls lsr-id 192.1.1.2
[Quidway-B] mpls
[Quidway-B-mpls] quit
[Quidway-B] mpls ldp

Huawei Technologies Proprietary

4-12
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-B] mpls l2vpn

# Configure VLAN 211.

[Quidway-B] vlan 211
[Quidway-B-vlan211] port gigabitethernet 2/1/1
[Quidway-B-vlan211] interface Vlan-interface 211
[Quidway-Vlan-interface 211] quit

# Configure the VLAN interface.

[Quidway-B] vlan 212
[Quidway-B-vlan212] port gigabitethernet 2/1/2
[Quidway-B-vlan212] quit
[Quidway-B] interface Vlan-interface 212
[Quidway-B-Vlan-interface212] ip address 169.1.1.1 255.255.0.0
[Quidway-B-Vlan-interface212] mpls
[Quidway-B-Vlan-interface212] mpls ldp enable

# Configure an IP address for the Loopback interface, which is used as the LSR ID.
[Quidway-B] interface loopback 0
[Quidway-B-LoopBack0] ip address 192.1.1.2 255.255.255.255

# Enable OSPF.
[Quidway-B] ospf 1
[Quidway-B-ospf-1] area 0.0.0.0
[Quidway-B-ospf-1-area-0.0.0.0] network 192.1.1.2 0.0.0.0
[Quidway-B-ospf-1-area-0.0.0.0] network 169.1.0.0 0.0.255.255
[Quidway-B-ospf-1-area-0.0.0.0] network 192.2.0.0 0.0.0.255

# Create an LSP tunnel.

[Quidway-B] mpls
[Quidway-B-mpls] mpls ldp

# Configure the LDP Remote Peer.

[Quidway-B] mpls ldp remote-peer 1
[Quidway-B-mpls-remote1] remote-ip 192.1.1.1

# Configure a Martini MPLS L2VPN connection.

[Quidway-B] interface vlan-interface 211
[Quidway-B-Vlan-interface211] mpls l2vc 192.1.1.1 20
3) Configure P.
# Configure the LSR ID. Enable MPLS, LDP, and MPLS L2VPN.
[Quidway-P] mpls lsr-id 192.1.1.3
[Quidway-P] mpls
[Quidway-P-mpls] quit
[Quidway-P] mpls ldp

Huawei Technologies Proprietary

4-13
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-P] mpls l2vpn

# Configure an IP address for the Loopback interface, which is used as the LSR ID.
[Quidway-P] interface loopback 0
[Quidway-P-LoopBack0] ip address 192.1.1.3 255.255.255.255
[Quidway-P-LoopBack0] quit

# Configure the VLAN interface.

[Quidway-P] vlan 211
[Quidway-P-vlan211] port gigabitethernet 2/1/1
[Quidway-P-vlan211] quit
[Quidway-P] interface Vlan-interface 211
[Quidway-P-Vlan-interface211] mpls
[Quidway-P-Vlan-interface211] mpls ldp enable
[Quidway-P-Vlan-interface211] ip address 168.1.1.2 255.255.0.0
[Quidway-P-Vlan-interface211] quit
[Quidway-P] vlan 212
[Quidway-P-vlan212 port gigabitethernet 2/1/2
[Quidway-P-vlan212] quit
[Quidway-P] interface Vlan-interface 212
[Quidway-P-Vlan-interface212] mpls
[Quidway-P-Vlan-interface212] mpls ldp enable
[Quidway-P-Vlan-interface212] ip address 169.1.1.2 255.255.0.0

# Enable OSPF.
[Quidway-P] ospf 1
[Quidway-P-ospf-1] area 0.0.0.0
[Quidway-P-ospf-1-area-0.0.0.0] network 168.1.0.0 0.0.255.255
[Quidway-P-ospf-1-area-0.0.0.0] network 169.1.0.0 0.0.255.255
[Quidway-P-ospf-1-area-0.0.0.0] network 192.1.1.3 0.0.0.0

Caution:

Following must be met to make an LDP Layer 2 VPN to go up:

z The interfaces of the two CE are physically up.
z Two LSP tunnels, which are opposite in direction, exist between two PEs.
z The encapsulation types of interfaces of the two CEs are the same and are
supported by the MPLS L2VPN.
z LDP remote sessions exist between PEs and are in Operational state.
To establish a tunnel, routes to the peer PE are necessary. So you need to configure
IGP (interior gateway protocol) on each router along the path, such as OSPF.

Huawei Technologies Proprietary

4-14
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

4.4 Kompella MPLS L2VPN Configuration

4.4.1 Configuring Kompella MPLS L2VPN

Table 4-4 Configure Kompella MPLS L2VPN

Configuration step Command Description

Enter system view system-view —
Configure the LSR
mpls lsr-id X.X.X.X Required
ID
Enable MPLS mpls Required
Required. In a Kompella MPLS
Perform BGP
L2VPN, the extended BGP is
(border gateway
used as the signaling protocol to
protocol) related
Refer to BGP distribute VC labels. So, you
configuration. Make
Configuration in Routing also need to configure BGP
sure BGP operates
Protocol module. parameters on PEs. As for the
properly and routers
MPLS L2VPN itself, it has no
can discover routes
special requirements on the
to other routers.
BGP configuration.
Enter L2VPN
l2vpn-family Required
address family view.
Required. By default, only the
peers of BGP IPv4 unicast
address families are active. The
Activate the peer or peer { group-name |
peer groups of other types are
peergroup. peer-address } enable
deactivated and thus cannot
exchange the routing
information.
Quit to system view quit —

Huawei Technologies Proprietary

4-15
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Configuration step Command Description

Required. The default
encapsulation type is Ethernet.
In the Kompella mode, the
encapsulation type of the access
side of the private network can
be Ethernet access and VLAN
access. Ethernet access is the
default type. If you configure the
encapsulation type as Ethernet
Create a VPN and mpls l2vpn vpn-name access, the port link type in a
specify the [ encapsulation private network VLAN is Access
encapsulation type. { ethernet | vlan } ] type; if you configure the
encapsulation type as VLAN
access, the port link type in a
private network VLAN is Trunk
type. It is not recommended to
use Hybrid type as the port link
type in a private network VLAN.
The user access modes of the
instance in all the peer PEs must
be consistent.
Required. For an MPLS L2VPN,
you must configure the RD
before performing other
configurations. An RD cannot be
modified once it is configured.
Configure the RD
route-distinguisher The only way to modify a
(route distinguisher)
route-distinguisher configured RD is to remove the
of the MPLS L2VPN
corresponding MPLS L2VPN
and create another one. As for
L2VPN, it is recommended that
you assign a unique RD for each
VPN.

vpn-target
vpn-target-ext-communit
Configure the
y
VPN-target of the Required
[ import-extcommunity
MPLS L2VPN
| export-extcommunity
| both ]
Configure the Layer
Optional. The same MTU value
2 MTU (maximum
mtu mtu must be configured for all PEs in
transmission unit) of
the same VPN.
the VPN
Create a CE or Required. Each CE created on a
ce name id id [ range
modify the CE PE needs to uniquely
range ] [ default-offset
Range of an existing correspond to one actual CE
offset ]
CE device connected to the PE. You
need to specify a unique ID for
these CEs. You can also specify
Enter an existing CE ce name the CE Range. It is desired that
the CE ID begins with 1 and
increases in step of 1.

Huawei Technologies Proprietary

4-16
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Configuration step Command Description

Required. When planning a
VPN, you can specify CE IDs for
CEs beginning with 1 and
increasing in step of 1, and then
connection [ ce-offset
Create connections establish connections by CE
offset ] { interface
between CEs IDs. You can establish
vlan-interface vlan-id }
connections with CE Offset not
provided for simplifying the
configuration. In this case, the
default CE Offset is used.

Caution:

z You can only change the CE range to a number larger than the existing one. For
example, you can change a CE range from 10 to 20, rather than from 10 to 5. The
only way to change a CE range to a smaller number is to remove the CE and create
a new one.
z You must use cards with suffix CA (such as LSB2FT48CA) on the public/private
network access side when configuring Kompella MPLS L2VPN.
z You can configure only one VLAN on the access side of each VPN private network.
Each VLAN can have only one interface. And all the VLANs connecting to the
interface must have IGMP disabled.
z In Kompella MPLS L2VPN, the encapsulation type on the access side of each
private network can be Ethernet access and VLAN access. Ethernet access is the
default type. If you configure the encapsulation type as Ethernet access, the port
link type in a private network VLAN is Access type; if you configure the
encapsulation type as VLAN access, the port link type in a private network VLAN is
Trunk type. It is not recommended to use Hybrid type as the port link type in a
private network VLAN. The user access modes of the instance in all the peer PEs
must be consistent.

4.4.2 Kompella MPLS L2VPN Configuration Example

I. Network requirements

CEs shown in Figure 4-6 are in the same VLAN as the corresponding PEs resides in. A
remote connection is required between CE-A and CE-B.

Huawei Technologies Proprietary

4-17
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

II. Network diagram

VLAN211
VLAN211 VLAN212

CE A VLAN212 PE A VLAN211 P VLAN212 PE B CE B

Figure 4-6 Network diagram for Kompella MPLS L2VPN

III. Configuration procedure

1) Configure PE-A.
# Enable MPLS globally.
[Quidway] mpls lsr-id 1.1.1.1
[Quidway] mpls

# Configure an IP address for the Loopback interface.

[Quidway] interface loopback 0
[Quidway-LoopBack0] ip address 1.1.1.1 32

# Enable MPLS L2VPN globally.

[Quidway] mpls l2vpn

# Configure VLAN 211.

[Quidway] vlan 211
[Quidway-vlan211] port gigabitethernet 2/1/1
[Quidway-Vlan211] interface vlan-interface 211
[Quidway-Vlan-interface211] quit

# Configure VLAN 212.

[Quidway] vlan 212
[Quidway-vlan212] port gigabitethernet 2/1/2
[Quidway-vlan212] interface vlan-interface 212
[Quidway-Vlan-interface212] quit

# Configure VLAN 213.

[Quidway] vlan 213
[Quidway-vlan213] port gigabitethernet 2/1/3
[Quidway-vlan213] interface vlan-interface 213
[Quidway-Vlan-interface 213] quit

# Enable MPLS on the interface of VLAN 214.

[Quidway] vlan 214
[Quidway-vlan214] port gigabitethernet 2/1/4
[Quidway-vlan214] quit
[Quidway] interface vlan-interface 214
[Quidway-Vlan-interface214] ip address 5.5.5.1 24
[Quidway-Vlan-interface214] mpls

Huawei Technologies Proprietary

4-18
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-Vlan-interface214] mpls ldp enable

[Quidway-Vlan-interface214] mpls ldp transport-ip interface
[Quidway-Vlan-interface214] quit

# Configure BGP.
[Quidway] bgp 100
[Quidway-bgp] group 100 internal
[Quidway-bgp] peer 100 connect-interface loopback0
[Quidway-bgp] peer 3.3.3.3 group 100
[Quidway-bgp] l2vpn-family
[Quidway-bgp-af-l2vpn] peer 100 enable

# Create and configure the VPN.

[Quidway] mpls l2vpn vpn1 encapsulation ethernet
[Quidway-mpls-l2vpn-vpn1] route-distinguisher 100:1
[Quidway-mpls-l2vpn-vpn1] vpn-target 100:1

# Create CE1 and configure the corresponding connection.

[Quidway-mpls-l2vpn-vpn1] ce ce1 id 1 range 200
[Quidway-mpls-l2vpn-vpn1-ce1] connection ce-offset 2 interface
vlan-interface 212
[Quidway-mpls-l2vpn-vpn1-ce1] connection ce-offset 3 interface
vlan-interface 213
[Quidway-mpls-l2vpn-vpn1-ce1] quit

# Enable OSPF.
[Quidway] ospf 1 router-id 1.1.1.1
[Quidway-ospf-1] area 0.0.0.0
[Quidway-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0
[Quidway-ospf-1-area-0.0.0.0] network 5.5.5.0 0.0.0.255
2) Configure PE-B.
# Enable MPLS globally.
[Quidway] mpls lsr-id 3.3.3.3
[Quidway] mpls

# Configure an IP address for the Loopback interface.

[Quidway] interface loopback 0
[Quidway-LoopBack0] ip address 3.3.3.3 32

# Enable MPLS L2VPN globally.

[Quidway] mpls l2vpn

# Configure VLAN 211.

[Quidway] vlan 211
[Quidway-vlan211] port gigabitethernet 2/1/1

Huawei Technologies Proprietary

4-19
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-vlan211] quit

# Configure VLAN 212.

[Quidway] vlan 212
[Quidway-vlan212] port gigabitethernet 2/1/2
[Quidway-vlan212] interface vlan-interface 212
[Quidway-Vlan-interface 212] quit

# Configure VLAN 213.

[Quidway] vlan 213
[Quidway-vlan213] port gigabitethernet 2/1/3
[Quidway-vlan212] interface vlan-interface 213
[Quidway-Vlan-interface 213] quit

# Enable MPLS on the interface of VLAN 214.

[Quidway] vlan 214
[Quidway-vlan214] port gigabitethernet 2/1/4
[Quidway-vlan214] quit
[Quidway] interface vlan-interface 214
[Quidway-Vlan-interface214] ip address 6.6.6.1 24
[Quidway-Vlan-interface214] mpls
[Quidway-Vlan-interface214] mpls ldp enable
[Quidway-Vlan-interface214] mpls ldp transport-ip interface
[Quidway-Vlan-interface214] quit

# Configure BGP.
[Quidway] bgp 100
[Quidway-bgp] group 100 internal
[Quidway-bgp] peer 100 connect-interface loopback0
[Quidway-bgp] peer 1.1.1.1 group 100
[Quidway-bgp] l2vpn-family
[Quidway-bgp-af-l2vpn] peer 100 enable

# Create and configure VPN1.

[Quidway] mpls l2vpn vpn1 encapsulation ethernet
[Quidway-mpls-l2vpn-vpn1] route-distinguisher 100 :1
[Quidway-mpls-l2vpn-vpn1] vpn-target 100 :1

# Create CE2 and configure the corresponding connection.

[Quidway-mpls-l2vpn-vpn1] ce ce2 id 2 range 200
[Quidway-mpls-l2vpn-vpn1-ce2] connection ce-offset 1 interface
vlan-interface 212
[Quidway-mpls-l2vpn-vpn1-ce2] quit
[Quidway-mpls-l2vpn-vpn1] ce ce3 id 3 range 200

Huawei Technologies Proprietary

4-20
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

[Quidway-mpls-l2vpn-vpn1-ce3] connection ce-offset 1 interface

vlan-interface 213
[Quidway-mpls-l2vpn-vpn1-ce3] quit

# Enable OSPF.
[Quidway] ospf 1 router-id 3.3.3.3
[Quidway -ospf-1] area 0.0.0.0
[Quidway -ospf-1-area-0.0.0.0] network 3.3.3.3 0.0.0.0
[Quidway -ospf-1-area-0.0.0.0] network 6.6.6.0 0.0.0.255
3) Configure the P device.
The configuration of P device is the same as that of standard MPLS configuration.
Refer to the P router Configuration of BGP/MPLS VPN in Basic MPLS Operation
Manual.

4.5 Displaying and Debugging MPLS L2VPN

After the above configuration, you can verify your configuration concerning MPLS
L2VPN by executing the display command in any view and checking the output
information.
You can execute the debugging command in user view to debug MPLS L2VPN.

Table 4-5 Display and debug L2VPN

Configuration
Command Description
step
Display information
display ccc [ ccc-name |
about a CCC MPLS
type [ local | remote ] ]
L2VPN connection
Display information
display mpls l2vc
about a Martini
[ interface vlan-interface
MPLS L2VPN
vlan-id | verbose ]
connection

display mpls l2vpn

[ vsi-name [ local-ce |
remote-ce ] | connection You can execute the display
Display information command in any view.
[ vsi-name [ down |
about a Kompella
remote-ce | up | verbose ] |
MPLS L2VPN
brief | interface
connection
Vlan-interface vlan-id ] |
forwarding-info { vc-label |
interface interface-type } ]
Display information
about the system or
display bgp l2vpn all
about Kompella
MPLS L2VPNs

Huawei Technologies Proprietary

4-21
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

Configuration
Command Description
step
debugging mpls l2vpn { all
| advertisement | error |
Enable debugging Execute this command in
event | connections
for MPLS L2VPN user view.
[ interface vlan-interface
vlan-id ] }

4.6 Troubleshooting MPLS L2VPN

Symptom 1: Fail to configure Layer 2 VPN on the VLAN interface.
Solution:
z Check to see if MPLS/BGP VPN, multicast, or VLL is enabled on the VLAN
interface. Because you cannot perform Layer 2 VPN configuration on a VLAN
interface if MPLS/BGP VPN, multicasting, or VLL is enabled on it.
z Check to see if the VLAN is a Super-Vlan or a Sub-Vlan. You can perform the
Layer 2 VPN configuration only on common VLAN interfaces.
Symptom 2: Fail to ping the peer from one end of a Martini MPLS L2VPN connection.
The VC is down and the Remote value is invalid.
Solution:
z VC state being down indicates the encapsulation types or VC IDs of the two ends
are not the same. Make sure the interface types (Access or Trunk) of the two PE
interfaces and the VC IDs of the two ends are consistent.
z As for the invalid Remote value, make sure you have configured the Remote
parameters and the peer addresses correctly.
Symptom 3: Fail to ping the peer of a Kompella MPLS L2VPN connection. The
Connection is down and the VPN value is null.
Solution:
z VPN value being null indicates the VPN is configured incorrectly. Make sure the
VPN configurations (such as RD) of the both ends are consistent, and the
connection configurations of the two CEs on both ends are correct.
z Connection being down indicates configurations concerning encapsulation of the
two ends are not the same. Make sure the encapsulation types and MTUs
configured for the local and remote PE devices are consistent. A connection fails if
the encapsulation types configured on the two ends are not the same.
Symptom 4: Fail to ping the peer end of a CCC MPLS L2VPN connection. The sending
and receiving channels are up, so does the linkconnection.
Solution:

Huawei Technologies Proprietary

4-22
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 4 MPLS L2VPN

z Make sure the in-label and out-label configured on the both ends correspond to
each other. If a P device exists, make sure its forwarding connection configuration
is correct, and the next hop configured statically is configured.

Huawei Technologies Proprietary

4-23
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

Chapter 5 Card Intermixing for MPLS Support

5.1 Overview
5.1.1 Introduction to Card Intermixing

For S8500 series routing switches, only the interface cards with suffixes C, CA and CB
and VPLS service processor cards support MPLS function. If you want to enable MPLS
VPN function of S8500 switches, you need MPLS-supporting interface cards or VPLS
service processor cards. The intermixing feature is used to enable deployment of
MPLS VPN services on cards that do not support MPLS. S8500 routing switches
support various modes of MPLS VPN function and provide abundant and differentiated
MPLS VPN service to meet the differentiated needs of different users in the
performance, reliability, port utilization of MPLS VPN functions.

Note:
z Unless otherwise specified, MPLS VPN services are processed by the
MPLS-supporting interface cards. In this manual, an interface card that supports
MPLS function is called MPLS card for short, and an interface card that does not
support MPLS function is called non-MPLS card for short.
z The purpose of card intermixing is to enable the non-MPLS cards to support MPLS
function through the MPLS cards. Refer to the “NAT&URPF&VPLS” section in this
manual for the information on the processing of MPLS VPN through VPLS service
processor cards.

5.1.2 Card Intermixing Mechanism

The implementation mechanism for card intermixing is as follows:

z The MPLS card and the non-MPLS card co-exist in the same switch;
z Use the port of the non-MPLS card for the access to the service private network
side of the MPLS VPN ;
z Redirect the port of the non-MPLS card through QACL, to redirect the received
packets to the specified MPLS card for processing;
z The port of MPLS card is set as Loopback port automatically and the port type is
Trunk;
z The access port of the non-MPLS card and the Loopback port of the MPLS card
belong to the same VLAN.

Huawei Technologies Proprietary

5-1
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

The port on the MPLS card can also be used for the access to the service private
network side of the MPLS VPN. In this case, you do not need to configure card
intermixing, and you must use the port of the MPLS card for the connection with the
MPLS public network side.

Note:
Because the destination port in intermixing configuration is to be looped back and
therefore is locked automatically, you cannot enter the port view. Therefore, you cannot
perform other configurations on the destination port.

5.2 Restrictions in Intermixing Networking

5.2.1 Rules of Intermixing Configuration

z A non-MPLS card can be used for access to the private network side, and an
MPLS card must be used for access to the public network side;
z You cannot perform other configurations on the destination port in intermixed
networking, that is to say, the port view is unavailable. In addition, the destination
port in intermixing networking cannot be deleted from the VLAN in the normal way,
and the destination port is an inloop port;
z The configured connection status of the source port in intermixing networking is
protected. For example, the port type cannot be changed form Trunk to Access or
from Access to Trunk, and the source port cannot be deleted from VLAN in the
normal way;
z The configuration of the service ports in intermixing networking cannot be
changed, and the service ports can be reconfigured only after the intermixing
configuration is removed;
z In a VLAN, multiple ports of the non-MPLS card can be redirected to one port of
the MPLS card. The destination port of the MPLS card is Looped back
automatically (becomes a Loopback port) after it is configured for redirection, and
you cannot perform other configurations on the port. Therefore, make sure that the
destination port is not in manual Shutdown state before configuring redirection.
Only one Loopback port is allowed in the redirected VLAN that the destination port
belongs to, but other MPLS card ports are allowed to join in;
z On the Trunk port of a non-MPLS card, you can redirect the MPLS VPNs of
multiple VLANs to one destination port to meet the need when the access CE is a
Layer 2 switch;
z In non-intermixing networking, VLL application requires that VLANs with only one
port be used at the private network side; In intermixing networking, VLL supports

Huawei Technologies Proprietary

5-2
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

only VLANs with two ports: one is the source port (port of the non-MPLS card) and
the other is the destination port (port of the MPLS card);
z When the source port (Trunk port) in intermixing networking belongs to multiple
VLANs, VPN binding must be implemented on the VLAN interfaces after the
redirection configuration;
z If VRRP is configured on the VLAN interface to which the redirected source port of
the MPLS VPN belongs, the plugging/unplugging of the MPLS card will cause
VRRP group state switching on the VLAN interface.

5.2.2 Restrictions in Card Intermixing

z Source port aggregation and destination port aggregation are not supported;
z Nested VPN is not supported;
z Super VLAN is not supported;
z It is not allowed to change the attributes of the redirected source port;
z It is not allowed to make the redirected source port or destination port to leave
redirected VLAN in the normal way;
z It is not allowed to configure protocol VLANs on the redirected source port or
destination port;
z It is not allowed to delete the redirected VLAN or VLAN interface;
z It is not allowed to configure/add Loopback ports in the redirected VLAN;
z It is not allowed to use STP edge port as the redirected destination port;
z It is not allowed to change the VLANs and the default VLAN ID which the
redirected destination port is permitted to pass;
z If normal ports are used, 4,094 VLL VPNs are supported; if the Trunk port of the
card of a fast Ethernet card is used, a maximum of 1024 VLL VPNs are supported;
z Only cards with suffix CA can be used at the public network side for VLL
configuration;
z Redirection configuration for MPLS VPN intermixing is not supported on the POS
and RPR ports, and the POS port cannot be used as the destination port for MPLS
VPN redirection;
A Trunk-type 100M Ethernet port can use only 1024 VLANs for VPN access or MPLS
forwarding, but you can specify the start VLAN ID of the 100M Ethernet Trunk port.
Assume the start VLAN ID is VLAN ID, the range of VLAN IDs of the VLANs that pass a
certain 100M Ethernet port is from VLAN ID to VLAN ID + 1023.

Huawei Technologies Proprietary

5-3
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

5.3 5.3 Introduction to intermixing configuration task

Table 5-1 Introduction to intermixing configuration task

Configuration task Description Detailed configuration

Configuring public network Refer to related sections in Routing
Required
routing protocols Protocol Operation
Configure the basic Refer to Chapter 2 in MPLS
Required
capability of MPLS Operation
Refer to Chapter 3 and Chapter 4 in
Configuring MPLS VPN Required
MPLS Operation
Configuring flow template
Required Refer to 5.3.5
and ACL rules
Applying flow template on
the port and configuring Required Refer to 5.3.5.
redirection

5.3.2 Configuring Routing Protocols

The Switch should be configured with some basic routing configurations so that it can
exchange public network routing information with other P devices and PE devices. The
routing protocols available currently include: static routing, RIP, OSPF, BGP and so on.
Refer to the “Routing Protocols” part of the Quidway S8500 Routing Switches
Operation Manual Volume I for detailed configuration information.

5.3.3 Configuring Basic Capability of MPLS

Configure MPLS basic capability to enable MPLS and LDP globally and on the public
network interface, to establish an LSP tunnel for the public network. Refer to Chapter 2
MPLS Basic Capability Configuration for detailed configuration information.

5.3.4 Configuring MPLS VPN

Configure BGP/MPLS VPN (L3VPN) or L2VPN. Refer to Chapter 3 BGP/MPLS VPN

Configuration and Chapter 4 MPLS L2VPN for detailed configuration information.

5.3.5 Configuring flow template and ACL rules

The packets to be redirected are identified through the flow template and ACL
configurations.

Huawei Technologies Proprietary

5-4
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

I. For L2VPN

Table 5-2 Configure the flow template and ACL of L2VPN

Operation Command Description

Enter system view system-view -

acl { number acl-number

Enter
| name acl-name link ] }
corresponding ACL Required
[ match-order { config |
view
auto } ]
Required.
L2VPN can use either the
default flow template or a
Configure rules of rule [ rule-id ] permit custom flow template. It is
ACL ingress vlan-id recommended to redirect the
packets in the specified VLAN
through matching them with a
Layer 2 rule so that the specified
VLAN packets can pass.

II. For L3VPN

Table 5-3 Configure flow template and ACL rules of L3VPN

Operation Command Description

Enter system view system-view -
Require.
When a custom flow template
flow-template is specified, at least two items
Set self-defined user-defined slot slotid IP and DMAC are required.
flow template dmac wildcard sip wildcard You can use the IP + VLAN +
vlanid DMAC method to define the
flow template so that different
kinds of packets are
processed in different ways.
acl { number acl-number |
Enter
name acl-name [ advanced
corresponding ACL Required
| basic ] } [ match-order
view
{ config | auto } ]
Required.
rule [ rule-id ] permit
Configure IP ACL source { source-addr You can use the parameter
wildcard | any } permit any or specify an IP
address.

Huawei Technologies Proprietary

5-5
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

Operation Command Description

Required.
Use a Layer 2 rule to
rule [ rule-id ] permit configure VLAN+DMAC.
Configure Layer 2 ingress vlan-id egress DMAC refers to the virtual
ACL dest-mac-addr MAC of the switch. You can
dest-mac-wildcard get it through the display
interface vlan vlanid
command.

You can define the flow template by means of the IP + VLAN + DMAC method to make
sure that different kinds of packets are processed in different ways:
z If ARP packets do not match IP rules in redirection, they will be processed on the
non-MPLS card;
z If Layer 2 traffic does not match DMAC in redirection, it will be L2-forwarded on the
non-MPLS card;
z If Layer 3 packets (including unicast protocol packets) match the rule, they will be
redirected to the MPLS card.
Refer to section “QACL” and the following networking example in the manual for
detailed information on configuring flow template and ACL rules.

5.3.6 Applying Flow Template and Redirection in Port Mode

Table 5-4 Applying Flow Template and Redirect in Port Mode

Operation Command Description

Enter system view system-view -
interface interface-type
Enter port view -
interface-number
Apply flow template
flow-template user-defined Required
in port mode

traffic-redirect inbound Required

ip-group { acl-number | l3-vpn | l2-vpn means the
acl-name } [ rule rule] command is applicable to
Configure the link-group [ rule rule ] L2VPN or L3VPN of MPLS.
traffic-redirect interface interface-type slot slotid vlanid: the slot id
command interface-number of the service card which
destination-vlan { l2-vpn | the VPLS packets are
l3-vpn } slot slotid vlanid redirected to and the ID of
[Join-vlan ] } the VLAN to join in.

The traffic-redirect command is used to enable ACL flow classification and redirect
the packets (only applicable to the rules whose action is permit in the ACL). There are
two kinds of redirection commands:

Huawei Technologies Proprietary

5-6
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

z Redirect packets to a port: You can redirect packets received by the source port of
the non-MPLS card to the specified destination port of the MPLS card.
z Redirect packets to a service processor card: You can redirect packets received by
the source port of the non-MPLS card or MPLS card to the VPLS card.
There are two kinds of redirection services:
z VPLS-related redirection services: The key word join-vlan must be specified, and
the system will add the current port into destination-vlan after the redirection
enabled; when redirection is disabled, the system will log the current port out of the
VLAN if what is deleted is a join-vlan enabled redirection in the VLAN.
z MPLS-independent redirection services: Such redirection services include NAT,
URPT, reflexive ACL, BT traffic control and so on. join-vlan cannot be enabled in
such a service. The port will not be added into VLAN when redirection is
configured, and the port will not be removed from the VLAN when redirection is
deleted.

Note:
z The source port joins in the corresponding VLAN automatically after the
configuration of intermixing redirection, and the source port leaves the
corresponding VLAN automatically after the intermixing redirection is deleted.
z When using the VPLS intermixing redirection command, you have to enable
join-vlan explicitly.
z When using the VLL VPN intermixing redirection command, you must not enable
the QinQ function on the source port and destination port.

5.3.7 Typical Networking Example

I. Network requirements

z CE1 and CE3 constitute VPN A, and CE2 and CE4 constitute VPN B. In PE1, a
port of an interface card with suffix C is shared, and in PE2, a Layer 2 switch is
shared to connect with the host directly.
z The PE devices (PE1 and PE2) are S8500 series switches, and the PE devices
need to support the MPLS function. CE1 and CE2 are common mid-range and
low-end routers. CE3 and CE4 are Layer 2 switches connected with users directly.
z The configurations of the interface cards of the two PE devices are the same. On
slot3 is a non-MPLS card with 100M Ethernet ports, and on Slot 2 is an MPLS card
with Gigabit Ethernet ports.

Huawei Technologies Proprietary

5-7
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

II. Networking diagram

MPLSNetwork
MPLS Netw ork vlan 10
loopback0 1.1.1.1/32
VLAN 211 Loopback0 1.1.1.1/32 loopback02.2.2.2/32
Loopback0 2.2.2.2/32 CE3
CE3
vlan 10
VLAN 10 VLAN 10
CE1
CE1 P VLAN
vlan 200300

VLAN 100 VLAN 200 vlan20

VLAN 20
VLAN 20
vlan 20 vlan 100
PE 11
PE VLAN100
vlan 100 vlan 300 PE 2
1 PE 2
P CE4
CE4
CE2
CE2

Figure 5-1 Network diagram for BGP/MPLS VPN intermixing

III. Configuration procedure

1) Configure CE1
# Configure CE1 and CE2 as EBGP neighbors and import direct routes and static
routes So that the VPN user routes of CE1 are imported into BGP routes and then
advertised to PE1.
<CE1>system-view
[CE1] vlan 211
[CE1] interface vlan-interface 211
[CE1-vlan-interface211] ip address 10.10.10.10 255.255.255.0
[CE1-vlan-interface211] quit
[CE1] bgp 65410
[CE1-bgp] group vpna external
[CE1-bgp] peer 10.10.10.1 group vpna as-number 100
[CE1-bgp] import-route direct
[CE1-bgp] import-route static

Note:
The configuration on CE2 is similar to that on CE1, so the configuration procedure is
omitted.

2) Configure PE1
# Configure global MPLS.
[PE1] mpls lsr-id 1.1.1.1
[PE1] mpls
[PE1] mpls ldp

# Configure public network interface and enable MPLS on the interface.

Huawei Technologies Proprietary

5-8
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

[PE1] interface loopback0

[PE1-LoopBack0] ip address 1.1.1.1 32
[PE1-LoopBack0] quit
[PE1] vlan 100
[PE1-vlan100] port GigabitEthernet 2/2/1
[PE1-vlan100] interface vlan-interface 100
[PE1-vlan-interface100] ip address 196.168.1.1 255.255.255.0
[PE1-vlan-interface100] mpls
[PE1-vlan-interface100] mpls ldp enable
[PE1-vlan-interface100] quit

# Enable OSPF on the interface connecting PE1 and P router and the Loopback
interface.
[PE1] ospf 1 route-id 1.1.1.1
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 196.168.1.0 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit

# Configure VPN-instance. The configuration of VPN B is similar to that of VPN A, so

followed is only the configuration of VPN A.
<PE1> system-view
[PE1] ip vpn-instance vpna
[PE1-vpn-vpna] route-distinguisher 100:1
[PE1-vpn-vpna] vpn-target 100:1 both
[PE1-vpn-vpna] quit

# Configure ACL and redirection, and configure a basic IP ACL to permit all the IP
packets in CE devices to be redirected.
[PE1] flow-template user-defined slot 3 dmac 0000-0000-0000 sip 0.0.0.0
vlan-id
[PE1] acl number 2000
[PE1-acl-basic-2000] rule 0 permit source any
[PE1-acl-basic-2000] quit
[PE1] acl number 4000
[PE1-acl-link-4000]rule 0 permit ingress 10 egress 00e0-fc99-6738
0000-0000-0000
[PE1-acl-link-4000] quit

Huawei Technologies Proprietary

5-9
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

Caution:

If the VRRP protocol is enabled on the VLAN port to which the source port of MPLS
VPN redirection belongs, you must configure another ACL rule to redirect the packets
whose destination address is the virtual MAC address of VRRP, so that ICMP packets
whose destination address is the virtual MAC address of VRRP can be processed
normally.

# Configure VLAN interface.

[PE1] vlan 10
[PE1-vlan10] interface vlan-interface 10
[PE1-vlan-interface10] quit

# Configure redirection on ports.

[PE1] interface Ethernet 3/1/1
[PE1-Ethernet3/1/1] flow-template user-defined
[PE1-Ethernet3/1/1] traffic-redirect inbound ip-group 2000 rule 0 link-group
4000 rule 0 interface GigabitEthernet 2/1/1 10 l3-vpn
[PE1-Ethernet3/1/1] quit

# Bind VPN A to the VLAN port connecting PE1 and CE1.

[PE1] interface vlan-interface 10
[PE1-vlan-interface10] ip binding vpn-instance vpna
[PE1-vlan-interface10] ip address 10.10.10.1 255.255.255.0
[PE1-vlan-interface10] quit

# Establish EBGP neighbor relationship between PE1 and CE1 and import the interface
routes of VPN-instance.
[PE1] bgp 100
[PE1-bgp] ipv4-family vpn-instance vpna
[PE1-bgp-af-vpn-instance] group vpna external
[PE1-bgp-af-vpn-instance] peer 10.10.10.10 group vpna as-number 65410
[PE1-bgp-af-vpn-instance] import-route direct
[PE1-bgp-af-vpn-instance] quit
[PE1-bgp] quit

# Establish MBGP neighbor relationship between PE and PE to exchange the VPN

routing information between the PEs and activate IBGP peers in VPNv4 address family
view.
[PE1] bgp 100
[PE1-bgp] group 100
[PE1-bgp] peer 2.2.2.2 group 100

Huawei Technologies Proprietary

5-10
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

[PE1-bgp] peer 2.2.2.2 connect-interface loopback0

[PE1-bgp] ipv4-family vpnv4
[PE1-bgp-af-vpn] peer 100 enable
[PE1-bgp-af-vpn] peer 2.2.2.2 group 100
3) Configure P
# Configure global MPLS.
[P] mpls lsr-id 3.3.3.3
[P] mpls
[P] mpls ldp

# Configure an interface and enable MPLS on the interface.

[P] interface loopback0
[P-LoopBack0] ip address 3.3.3.3 32
[P-LoopBack0] quit
[P] vlan 100
[P-vlan100] port GigabitEthernet 2/1/1
[P-vlan100] interface vlan-interface 100
[P-vlan-interface100] ip address 196.168.1.2 255.255.255.0
[P-vlan-interface100] mpls
[P-vlan-interface100] mpls ldp enable
[P-vlan-interface100] quit
[P] vlan 200
[P-vlan200] port GigabitEthernet 2/1/2
[P-vlan200] interface vlan-interface 200
[P-vlan-interface200] ip address 196.168.2.2 255.255.255.0
[P-vlan-interface200] mpls
[P-vlan-interface200] mpls ldp enable
[P-vlan-interface200] quit

# Configure OSPF.
[P] ospf 1 route-id 3.3.3.3
[P-ospf-1] area 0
[P-ospf-1-area-0.0.0.0] network 196.168.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 196.168.2.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 3.3.3.3 0.0.0.0
4) Configure PE2
# Configure global MPLS.
[PE2] mpls lsr-id 2.2.2.2
[PE2] mpls
[PE2] mpls ldp

# Configure a public network interface and enable MPLS on the interface.

[PE2] interface loopback0

Huawei Technologies Proprietary

5-11
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

[PE2-LoopBack0] ip address 2.2.2.2 32

[PE2-LoopBack0] quit
[PE2] vlan 300
[PE2-vlan300] port GigabitEthernet 2/2/1
[PE2-vlan300] interface vlan-interface 300
[PE2-vlan-interface300] ip address 196.168.2.1 255.255.255.0
[PE2-vlan-interface300] mpls
[PE2-vlan-interface300] mpls ldp enable
[PE2-vlan-interface300] quit

# Enable OSPF on the interface connecting PE2 with P router and the Loopback
interface.
[PE2] ospf 1 route-id 2.2.2.2
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 196.168.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] network 2.2.2.2 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit

# Configure VPN-instance. The configuration of VPN B is similar to that of VPN A, so

followed is only the configuration of VPN A.
[PE2] ip vpn-instance vpna
[PE2-vpn-vpna] route-distinguisher 100:1
[PE2-vpn-vpna] vpn-target 100:1 both
[PE2-vpn-vpna] quit

# Configure ACL, redirection and Layer 2 ACL (Custom flow template should be
configured before this step).
[PE2] acl number 2000
[PE2-acl-basic-2000] rule 0 permit source any
[PE2-acl-basic-2000] quit
[PE2] flow-template user-defined slot 3 dmac 0000-0000-0000 sip 0.0.0.0
vlan-id
[PE2] acl number 4000
[PE2-acl-link-4000] rule 0 permit ingress 10 egress 00e0-fc99-6738
0000-0000-0000
[PE2-acl-link-4000] quit

# Configure VLAN interface.

[PE2] vlan 10
[PE2-vlan10] interface vlan-interface 10
[PE2-vlan-interface10] quit

# Configure redirection on the port.

[PE2] interface Ethernet 3/1/1
[PE2-Ethernet3/1/1] port link-type trunk

Huawei Technologies Proprietary

5-12
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

[PE2-Ethernet3/1/1] flow-template user-defined

[PE2-Ethernet3/1/1] traffic-redirect inbound ip-group 2000 rule 0 link-group
4000 rule 0 interface GigabitEthernet 2/1/1 10 l3-vpn

# Bind VPN A on the VLAN interface between PE2 and CE3.

[PE2] interface vlan-interface 10
[PE2-vlan-interface10] ip binding vpn-instance vpna
[PE2-vlan-interface10] ip address 20.2.1.2 255.255.255.0
[PE2-vlan-interface10] quit

# Import the interface routes of private network between PE2 and CE 3 for VPNA.
[PE2] bgp 100
[PE2-bgp] ipv4-family vpn-instance vpna
[PE2-bgp-af-vpn-instance] import-route direct
[PE2-bgp-af-vpn-instance] quit
[PE2-bgp] quit

# Establish MBGP neighbor relationship between PE and PE to exchange VPN routing

information between PEs and activate IBGP peers in VPNv4 address family view.
[PE2] bgp 100
[PE2-bgp] group 100
[PE2-bgp] peer 1.1.1.1 group 100
[PE2-bgp] peer 1.1.1.1 connect-interface loopback0
[PE2-bgp] ipv4-family vpnv4
[PE2-bgp-af-vpn] peer 100 enable
[PE2-bgp-af-vpn] peer 1.1.1.1 group 100

Note:
The configuration of L2 VPN VLL intermixing is similar to that of L3VPN intermixing, so
the description of configuration process is omitted. The configuration of L2 VPN VLL
intermixing is also implemented through the traffic-redirect command. You do not
need to customize the flow template needed for VLL redirection and you can use the
default flow template. In addition, the flow template only needs to match Layer 2 ACL of
4000 series and only the VLAN ID needs to be specified in ACL rules.

5.4 Restrictions in Networking of Various MPLS Cards

Huawei Technologies Proprietary

5-13
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

Note:
MPLS cards with suffix CA support VLL and BGP/MPLS VPN, and common MPLS
cards (with suffix C0) do not support VLL.

5.4.1 Exclusively non-MPLS Cards

I. Introduction to networking

Non-MPLS cards do not support related MPLS functions.

II. Configuration restrictions

If related MPLS service is configured, the service cannot work normally.

5.4.2 Exclusively MPLS Cards

I. Introduction to networking

MPLS cards support MPLS VPN (VLL and BGP/MPLS VPN), and VLL and BGP/MPLS
VPN can be configured on MPLS cards at the same time.

II. Configuration restrictions

z Not supporting VPLS;

z VLL and BGP/MPLS VPN cannot be configured on a VLAN interface at the same
time.

5.4.3 Exclusively VPLS Service Cards

I. Introduction to networking

This networking mode does not exist. Other service cards are needed to forward data.

II. Configuration restrictions

None.

5.4.4 Combination of One MPLS Card and Multiple non-MPLS Cards

I. Introduction to networking

The deployment of MPLS VPN (VLL and BGP/MPLS VPN) services can be
implemented on non-MPLS cards through card intermixing configuration.

II. Configuration restrictions

z VLL and BGP/MPLS VPN are mutually exclusive, so it is not allowed to configure
the two types of services on the same VLAN interface;

Huawei Technologies Proprietary

5-14
Operation Manual Volume II – MPLS
Quidway S8500 Series Routing Switches Chapter 5 Card Intermixing for MPLS Support

z In card intermixing networking, non-MPLS cards can only be used for access at
the private network side, and MPLS card must be used for access at the public
network side.
z MPLS card has influence on the forwarding performance of a switch.

5.4.5 Combination of Multiple MPLS cards and Multiple non-MPLS Cards

I. Introduction to networking

The combination of multiple MPLS cards and multiple non-MPLS cards is similar to
“Combination of one MPLS card and multiple non-MPLS cards” in Section 5.4.4;
however, MPLS VPN services can be processed on the MPLS cards directly, without
the need of card intermixing configuration.

II. Configuration restrictions

It is not allowed to bind VLL and BGP/MPLS VPN to the same VLAN.

5.4.6 Combination of One VPLS Card and Multiple non-MPLS Cards

I. Introduction to networking

A VPLS card supports VPLS. However, a VPLS card does not have egress interfaces,
so another interface card must be used data forwarding.

5.4.7 Combination of One VPLS card and Multiple MPLS Cards

I. Introduction to networking

VPLS cards can work with any type of interface cards to support VPLS.

5.4.8 Combination of One VPLS card, One MPLS Card and Multiple
non-MPLS Cards

I. Introduction to networking

Assume only non-MPLS cards were used at the beginning, and then one MPLS card
was added to support MPLS VPN services (VLL and BGP/MPLS VPN) through card
intermixing configuration. Then one VPLS card was added to process VPLS services.

II. Configuration restrictions

The MPLS card is used to process MPLS VPN services. It is recommended to use
non-MPLS cards for the access of MPLS services at the private network side.

Huawei Technologies Proprietary

5-15