Scribd
Upload
133 views

Packet Tracer - Configure Ipv6 Addressing

This document describes configuring IPv6 addressing on a router and connected devices. It involves assigning IPv6 addresses to interfaces on the router according to an addressing table. It also includes assigning IPv6 addresses to servers and clients based on the table. Finally, connectivity is tested by accessing server web pages from clients and pinging the ISP address from various devices.

Uploaded by

Yana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
133 views

Packet Tracer - Configure Ipv6 Addressing

This document describes configuring IPv6 addressing on a router and connected devices. It involves assigning IPv6 addresses to interfaces on the router according to an addressing table. It also includes assigning IPv6 addresses to servers and clients based on the table. Finally, connectivity is tested by accessing server web pages from clients and pinging the ISP address from various devices.

Uploaded by

Yana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Packet Tracer - Configure IPv6 Addressing

Addressing Table
Device Interface IPv6 Address/Prefix Default Gateway

R1 G0/0 2001:db8:1:1::1/64 N/A

R1 G0/0
fe80::1 N/A

R1
G0/1 2001:db8:1:2::1/64 N/A

R1 G0/1
fe80::1 N/A

R1
S0/0/0 2001:db8:1:a001::2/64 N/A

R1 S0/0/0
fe80::1 N/A

Sales NIC 2001:db8:1:1::2/64 fe80::1


Billing NIC 2001:db8:1:1::3/64 fe80::1
Accounting NIC 2001:db8:1:1::4/64 fe80::1
Design NIC 2001:db8:1:2::2/64 fe80::1
Engineering NIC 2001:db8:1:2::3/64 fe80::1
CAD NIC 2001:db8:1:2::4/64 fe80::1
ISP S0/0/0 2001:db8:1:a001::1 fe80::1

Objectives
Part 1: Configure IPv6 Addressing on the Router
Part 2: Configure IPv6 Addressing on Servers
Part 3: Configure IPv6 Addressing on Clients
Part 4: Test and Verify Network Connectivity

Background
In this activity, you will practice configuring IPv6 addresses on a router, servers, and clients. You will
also practice verifying your IPv6 addressing implementation.

Part 1: Configure IPv6 Addressing on the Router


Step 1: Enable the router to forward IPv6 packets.
a.     Click R1 and then the CLI tab. Press Enter.
Open a configuration window

b.     Enter privileged EXEC mode.


c.     Enter the ipv6 unicast-routing global configuration command. This command must be entered to
enable the router to forward IPv6 packets.
R1(config)# ipv6 unicast-routing

Step 2: Configure IPv6 addressing on GigabitEthernet0/0.


a.     Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/0.
b.     Configure the IPv6 address with the following command:
R1(config-if)# ipv6 address 2001:db8:1:1::1/64
c.     Configure the link-local IPv6 address with the following command:
R1(config-if)# ipv6 address fe80::1 link-local
d.     Activate the interface.
R1(config-if)# no shutdown

Step 3: Configure IPv6 addressing on GigabitEthernet0/1.


a.     Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/1.
b.     Refer to the Addressing Table for the correct IPv6 address.
c.     Configure the IPv6 address, the link-local address and activate the interface.

Step 4: Configure IPv6 addressing on Serial0/0/0.


a.     Enter the commands necessary to move to interface configuration mode for Serial0/0/0.
b.     Refer to the Addressing Table for the correct IPv6 address.
c.     Configure the IPv6 address, the link-local address and activate the interface.

Step 5: Verify IPv6 addressing on R1.


It is good practice to verify addressing when it is complete by comparing configured values with the
values in the addressing table.
a.     Exit configuration mode on R1.
b.     Verify the addressing configured by issuing the following command:
R1# show ipv6 interface brief
c.     If any addresses are incorrect, repeat the steps above as necessary to make any corrections.
Note: To make a change in addressing with IPv6, you must remove the incorrect address or else
both the correct address and incorrect address will remain configured on the interface.
Example:
R1(config-if)# no ipv6 address 2001:db8:1:5::1/64
d.     Save the router configuration to NVRAM.
Close a configuration window

Part 2: Configure IPv6 Addressing on the Servers


Step 1: Configure IPv6 addressing on the Accounting Server.
a.     Click Accounting and click the Desktop tab > IP Configuration.
b.     Set the IPv6 Address to 2001:db8:1:1::4 with a prefix of /64.
c.     Set the IPv6 Gateway to the link-local address, fe80::1.

Step 2: Configure IPv6 addressing on the CAD Server.


Configure the CAD server with addresses as was done in Step 1. Refer to the Addressing Table for
the addresses to use.

Part 3: Configure IPv6 Addressing on the Clients


Step 1: Configure IPv6 addressing on the Sales and Billing Clients.
a.     Click Billing and then select the Desktop tab followed by IP Configuration.
b.     Set the IPv6 Address to 2001:db8:1:1::3 with a prefix of /64.
c.     Set the IPv6 Gateway to the link-local address, fe80::1.
d.     Repeat Steps 1a through 1c for Sales. Refer to the Addressing Table for the IPv6 address.

Step 2: Configure IPv6 Addressing on the Engineering and Design Clients.


a.     Click Engineering and then select the Desktop tab followed by IP Configuration.
b.     Set the IPv6 Address to 2001:db8:1:2::3 with a prefix of /64.
c.     Set the IPv6 Gateway to the link-local address, fe80::1.
d.     Repeat Steps 2a through 2c for Design. Refer to the Addressing Table for the IPv6 address.

Part 4: Test and Verify Network Connectivity


Step 1: Open the server web pages from the clients.
a.     Click Sales and click the Desktop tab. Close the IP Configuration window, if necessary.
b.     Click Web Browser. Enter 2001:db8:1:1::4 in the URL box and click Go.
The Accounting website should appear.
c.     Enter 2001:db8:1:2::4 in the URL box and click Go. The CAD website should appear.
d.     Repeat steps 1a through 1c for the rest of the clients.
Step 2: Ping the ISP.
a.     Click on any client.
b.     Click the Desktop tab > Command Prompt.
c.     Test connectivity to the ISP by entering the following command:
PC> ping 2001:db8:1:a001::1
d.     Repeat the ping command with other clients until full connectivity is verified.
End of Document

You might also like