Service Manual: /mitsubishi
Service Manual: /mitsubishi
COLOR MONITOR
SERVICE MANUAL
Better Service
Better Reputation
Better Profit
MODELS:
MultiSync V920
MultiSync V921-1
MultiSync 95
AccuSync 90
AccuSync 90 M
(N9902-1 Series Model)
/MITSUBISHI
NEC-MITSUBISHI ELECTRIC VISUAL SYSTEMS
This equipment utilized a micro-gap power switch. Turn off the monitor by first
pushing the front panel power switch. Next, remove the power cord from the AC
outlet.
To prevent fire or shock hazards, do not expose this unit to rain or moisture
This symbol warns the personnel that un-insulated voltage within the unit
may have sufficient magnitude to cause electric shock.
This symbol alerts the personnel that important literature concerning the
! operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
Page No.
SPECIFICATIONS ...................................................................................................... 1
CONTROLS ................................................................................................................ 2
DISASSEMBLY .......................................................................................................... 5
3) MultiSync 95 ............................................................................................. 55
4) AccuSync 90 ............................................................................................. 57
SCHEMATIC ............................................................................................................. 63
– +
SELECT RESET
On-screen display control buttons on the front of the monitor Function as follows:
SELECT Enters and exits the OSD menu and decides the icon.
CONTROL − / + Selects one of the controls and increases or decreases the
adjustment.
RESET Resets the highlighted control to the factory Setting.
Increases or decreases the top of the screen to be the same as the bottom.
Increases or decreases the tilt of the sides either to the left or right.
9300 This color setting is adjusted at the factory to the stated Kelvin
OSD: There are 3 background color (blue,black, and white). To choose background
color, press SELECT button after the selection of OSD in “Icon select window”.
EXIT: To exit the OSD window. Select EXIT in “Icon select window”, then push
SELECT button to exit OSD window.
Note: If no buttons are pushed after 10 seconds while in OSD, the window will
automactically disappear.
MODEL N9902
SERIAL No.
Manufactured Year :
( Last digit )
Manufactured Month :
January to September 1 to 9
October X 00001 ~ on ward
November Y (Start from 00001 ~ when
December Z month is changed.)
Factory mark :
• Before you disassemble the set, turn off power and pull out the power plug.
• Use a proper screwdriver. If you user screwdriver that does not fit, you may damage the
screws.
• Disassembly is the opposite process of assembly.
• Carefully discharge the CRT anode potential by grounding to CRT dag ground harness before
removing Anode Cap.
EXPLANATION
TABLE OF CONTENTS
Page
(1) Adjustment Tools ........................................................................................................................... 7
(2) Timing Table .................................................................................................................................. 7
(3) Definition for Normal Condition ...................................................................................................... 7
(4) B+ Adjustment ............................................................................................................................... 7
(5) Free Run Adjustment ..................................................................................................................... 8
(6) H. V. Adjustment ............................................................................................................................ 8
(7) X-ray Test ...................................................................................................................................... 8
(8) H-Center Adjustment ..................................................................................................................... 8
(9) H-Size Adjustment ......................................................................................................................... 8
(10) Mode 11 Pre-Adjustment ............................................................................................................. 8
(11) G2 Voltage Adjustment(Raster Brightness Adjustment) ............................................................. 8
(12) Focus Adjust ................................................................................................................................ 9
(13) Convergence Adjust .................................................................................................................... 9
(14) Automatically Adjust .................................................................................................................... 9
(15) White Balance Adjustment .......................................................................................................... 9
(16) White Balance Check and ABL Adjust ........................................................................................ 9
(17) Power Saving Test .................................................................................................................... 10
(18) DCC 1/2B Test .......................................................................................................................... 10
(19) Timing Table .............................................................................................................................. 11
Reference
(4) B+ Adjustment:
10
P re s e t M o d e N o . 1 2 3 4 5 6
VGA VGA VESA VESA VESA (M A C )
S ig n a l N a m e 6 4 0 *4 0 0 6 4 0 *4 8 0 6 4 0 *4 8 0 6 4 0 *4 8 0 8 0 0 *6 0 0 8 3 2 *6 2 4
(7 5 ) (8 5 ) (7 5 ) (7 5 )
R e s o lu tio n 6 4 0 *4 0 0 6 4 0 *4 8 0 6 4 0 *4 8 0 6 4 0 *4 8 0 8 0 0 *6 0 0 8 3 2 *6 2 4
D o t C lo c k (M H z) 2 5 .1 7 5 2 5 .1 7 5 3 1 .5 0 0 3 6 .0 0 0 4 9 .5 0 0 5 7 .2 8 3
fh (k H z ) 3 1 .4 7 3 1 .4 6 9 3 7 .5 0 4 3 .2 6 9 4 6 .8 7 5 4 9 .7 2 5
fv (H z ) 7 0 .0 9 5 9 .9 4 0 7 5 .0 0 8 5 .0 0 8 7 5 .0 0 7 4 .5 5 0
To ta l (d o t) 800 800 840 832 1056 11 5 2
(u S ) 3 1 .7 8 3 1 .7 7 8 2 6 .6 6 7 2 3 .111 2 1 .3 3 3 2 0 .111
D is p (d o t) 640 640 640 640 800 832
(u S ) 2 5 .4 2 2 5 .4 2 2 2 0 .3 1 7 1 7 .7 7 8 1 6 .1 6 2 1 4 .5 2 3
F ro n t (d o t) 16 16 16 56 16 32
(u S ) 0 .6 4 0 .6 3 6 0 .5 0 8 1 .5 5 6 0 .3 2 3 0 .5 5 9
S yn c P u ls e (d o t) 96 96 64 56 80 64
(u S ) 3 .1 8 3 .8 1 3 2 .0 3 2 1 .5 5 6 1 .6 1 6 1 .11 7
B ack (d o t) 48 48 120 80 160 224
(u S ) 1 .9 1 1 .9 0 7 3 .8 1 0 2 .2 2 2 3 .2 3 2 3 .9 1 0
To ta l (H ) 449 525 500 509 625 667
(m S ) 1 4 .2 6 8 1 6 .6 8 3 1 3 .3 3 3 11 .7 6 4 1 3 .3 3 3 1 3 .4 1 4
D is p (H ) 400 480 480 480 600 624
(m S ) 1 2 .7 11 1 5 .2 5 3 1 2 .8 0 0 11 .0 9 3 1 2 .8 0 0 1 2 .5 4 9
F ro n t (H ) 12 10 1 1 1 1
(m S ) 0 .3 8 1 0 .3 1 8 0 .0 2 7 0 .0 2 3 0 .0 2 1 0 .0 2 0
S yn c P u ls e (H ) 2 2 3 3 3 3
(m S ) 0 .0 6 4 0 .0 6 4 0 .0 8 0 0 .0 6 9 0 .0 6 4 0 .0 6 0
B ack (H ) 35 33 16 25 21 39
(m S ) 1 .11 2 1 .0 4 9 0 .4 2 7 0 .5 7 8 0 .4 4 8 0 .7 8 4
In te rla c e NON NON NON NON NON NON
P o la rity ( H /V ) N E G /P O S N E G /N E G N E G /N E G N E G /N E G P O S /P O S N E G /N E G
C o m p o s ite S yn c
C o m p o s ite V id e o
C h a ra c te r F o n t 7*9 7*9 7*9 7*9 7*9 7*9
S e rra tio n O FF O FF O FF O FF O FF O FF
EQP O FF O FF O FF O FF O FF O FF
11
12
13
1. Construction of System
Program Disk
Monitor
PC
Signal Cable
Fixture Power Cable
2) Run the specified EDID write and inspection program under PC-DOS mode.
14
Digit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Format * N N N N N N N N _ Y M S S S S S F R *
Example * N A 5 0 0 0 8 T _ 0 6 0 0 0 0 1 Y A *
*+Model Code + 1 space + Serial No. + *
Serial No. Descriptions;
Y: Manufactured Year (Last digit) ex. 0 à 2000
M: Manufactured Month 1 ~ 9, X(October), Y(Novenber), Z(December)
S: Serial No. ( 5digits) 00001 ~ onward (restart when month is changed)
F: Factory Code: Y is NPG China Factory
R: Product Revision code: start from A
EDID Code Input Procedure ex.
1) Scan Bar code (20 digits) NA50008T_ 9600001YA
2) Skip 9 digits then find the Serial No. 0600001YA
3) Make Year hex Code from Year digit 0 à 0Ah
4) Make Week hex Code from Month digit 6*4 = 24 à 18h
5) Change Serial No. to ASCII code 30h 36h 30h 30h 30h
30h 31h 59h 41h
6) Apply Serial No. Information to the default EDID code.
7) Download EDID from PC to Monitor.
8) DDC1 Inspection
9) DDC2B Inspection
15
16
Refer to User’s Manual trouble shooting section before using this chart.
TABLE OF CONTENTS
Page
4 . NO VIDEO ................................................................................................................................... 21
17
POWER SW
TURN OFF
MULTIMETER TEST
Q315, Q312, D114,
D110,D111,D112,D113
POWER SW
TURN OFF
18
POWER SW
TURN OFF
CHECK
F101
CHECK
Q101
U101
CHECK
U101 PIN6 U101 PIN 7 VCC
NO
PULSE O/P
PIN 4 SAWTOOTH
POWER SW FAILURE
TURN ON R111, ZD103
19
CHECK
Q101 G-S FREQUENCY
YES
YES
CHECK
Q312 FREQUENCY
SYNCRONIZE
CHECK U301 NO
WITH H-SYNC
NORMAL OPERATION
20
NO VIDEO
YES
CHECK
REFER
SCREEN CONTROL NO
NO RASTER
CLOCKWISE
YES
CHECK TROUBLE IN
U201 PIN 2, 6, 11 NO R/G/B SIGNAL,
SIGNAL LEVEL SIGNAL CABLE
YES
YES
CHECK
TROUBLE IN U203
U203 PIN 1, 3, 5 NO
SIGNAL LEVEL 8V, 12V, 80V VOLTAGE
YES
CHECK
TROUBLE IN U203
CATHODE VIDEO NO
LEVEL R220, R240, R260
YES
TROUBLE IN CRT
21
NO RASTER
YES
YES
CHECK
U301 PIN 1, PIN 2 NO TROUBLE IN
H/V SYNC MCU U701
YES
CHECK
NO
U701 PIN 31 IS LOW
YES
CHECK
TROUBLE IN
U301 PIN 26, 28 NO
H/V SYNC U301
YES
CHECK TROUBLE IN
T302 PIN 3 VOLTAGE U301,Q312,D317,D111,R387,
NO
57V AT 31.5KHz, 172V R312, Q307, Q308
AT 93.7KHz OR DEFLECTION YOKE
YES
YES
CHECK G1 TROUBLE IN
VOLTAGE ABOUT NO Q331, Q323, Q329, R394,
-45~65V D314, T302, C328, U701
YES
TROUBLE IN
G2 VOLTAGE
22
TROUBLE IN
HOR. OR VER. SYNC
YES
CHECK
CONNECTOR S701 TROUBLE IN
NO
(PIN6,7), SIGNAL SIGNAL CABLE
YES
CHECK
TROUBLE IN
U701(PIN 39,40)
NO H/V SYNC LINE &
H/V SYNC.
Q701, Q702
SIGNAL
YES
CHECK CHECK
U701(PIN 32,33) U701(PIN 5) TROUBLE IN
NO NO
H/V SYNC. VOLTAGE 5V LINE
SIGNAL 5V?
YES
YES
CHECK
U701 (PIN 7, 8) TROUBLE IN
YES NO
FREQ.12MHz X701, U701
CHECK TROUBLE IN
NO H.V SIGNAL LINE
U701(PIN 1, 2)
R301, R302, C706,
C301, C302
YES
TROUBLE IN
U301
23
PINCUSHION
YES
PARABOLA
WAVE YES CHECK Q309, Q311,
NO
CHECK
U301 PIN 24 CHECK C350, Q332,
YES
PARABOLA R30V, R30W
NO
TROUBLE IN U301
24
FOCUS POOR
YES
NO
TROUBLE IN
CHECK
T303, Q305, R360, R32H,
T303 H AND V PARABOLA NO R331, R339, C322, C324,
WAVEFORM V-PARABOLA C320
NO
CHECK
C323 H-PARABOLA
YES TROUBLE IN T303
WAVEFORM 29Vpp
NO
CHECK
Q303, Q304 EMITTER TROUBLE IN
NO
H-PARABOLA Q302, Q303, Q304, Q338
32-Vpp
YES
CHECK
TROUBLE IN
Q301, Q317 COLLECT NO
H-PARABOLA Q301, Q307
5-Vpp
YES
GO TO
FACTORY MODE,
CHOICE H-FOCUS ICON, ADJUST
TO 80~100%, CHECK U301
10PIN FOCUS 3.8Vpp
NO
TROUBLE IN U301
25
Page
26
(a) The filter network consists of L104, C101, C107, L101, L102, C103 and C104. The main function of this
filter circuit is to eliminate the noise that is produced from monitor itself.
(b) T101 is an energy converter which transfers the energy from primary winding to secondary load. R105,
C112 and D105 are the snubber circuit and they function to absorb the spike to protect Q101.
(c) U101 is a pulse width modulation IC which supplies the drive pulse to Q101. The sync pulse is got from
FBT secondary to ensure the power supply and horizontal deflection are synchronized.
(d) D110, D111, D112, D113, D114 are output rectifier diodes which are filtered by C119, C120, C121,
C122 and C143. The output voltage will supply and control all the deflection circuit.
(e) DC to DC step-up PWM is output from U301 pin28. This waveform through Q307 and Q308 to drive the
Q312. This pulse width is varied with horizontal frequency, and then the DC voltage is difference of
FBT pin3.
The video amplifier system is consist of the Pre-Amplifier, the Video-Power-Amplifier, and the cutoff-
Voltage circuit.
(a)The U201 (M52743B) is a three channel video pre-amplifier IC, that controlled by MCU IIC bus for the
features of contrast, output DC level, 3 SUB gain controls (R-Gain, G-Gain, B-Gain).
(b)U201 PIN 19 need a positive pulse for clamping and PIN 27 also need a positive pulse for blanking.
(c)The OSD mixer processes are on pin 2, 3, 4, and the OSD Blk input on pin 1.
(d)The Video-Power-Amplifier U203 (LM2435) is a three channel hybrid IC which functions as a cascade
type transistor amplifier to reach the high bandwidth performance.
(e)The Cutoff- Adjusting circuit is consist of Q211, Q212, Q231, Q232, Q251 and Q252 to provide the
function of background white-balance.
(f)The U202 (MTV021N-38) is a OSD generator outputs the R. G. B. and FBLK signals that MCU shows
the monitor’s status and the user adjusting indications. This IC is synchronized by horizontal and
vertical sync input on pin 5 and pin 10.
27
(b)The U702 is an EEPROM IC which stores the parameters of each mode and the user adjusting result
and also DDC data. It is controlled by IIC bus from MCU.
4. Vertical Deflection
(a)Vertical deflection Saw-tooth waveform is provided by U301, pin 23, and amplified by U401
TDA8172.
(b)A voltage multiplier connected to pin 3 and pin 6, consists of D402, C409 to avoid flyback scanning
line appeared during the vertical flyback period.
(c)U301 (TDA9111) pin 21 provides a DC level as a V-Position control voltage.
(d)U401 pin 5 is output to drive vertical yoke.
5. Horizontal Deflection
(a)U301 is a horizontal signal processing IC. Horizontal Driver signal is output from pin 26 of U301
TDA9111 and through Q333, Q334 to drive Q316 and T301.
(b)T301 is an on/off type driver transformer. It functions to convert primary energy to secondary, and
drive the horizontal output transistor Q315, R369 and C363 are the snubber.
28
(2)The control voltage is from U701 pin 30, it varied with horizontal frequency. When the horizontal
frequency > 52K, U701 pin 36 output voltage is high and L302 is on, the horizontal frequency <
52K U701 pin 30 output voltage is low and the L302 is off.
(3)C344 is the Cs capacitor, and Q324 controls C345, Q326 controls C347, Q325 controls C346,
Q327 controls C348. The U701 pin 1, 2, 3, 4 controls the Q324, Q326, Q325 and Q327
respectively. So different frequency has different combination to meet the requirement.
Cs Table By Frequency
CS1 CS2 CS3 CS4
FH < 30K 0 0 0 0
30K < fH < 34K 0 0 0 0
34K < fH < 36.5K 0 0 1 0
36.5K < fH < 45K 0 1 1 0
45K < fH < 52K 1 0 0 1
52K < fH < 62.5K 1 1 0 1
62.5K < fH < 67K 0 0 1 1
67K < fH < 74K 1 0 1 1
74K < fH < 83K 1 1 1 1
83K < fH < 96.5K 1 1 1 1
96.5 < fH 1 1 1 1
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
53
54
55
56
57
58
59
60
61
H/H+V
Micro-Processor OSD Process Horizontal & Vertical AMP
Output V-DY
V U701 U202 Vertical Process
U301 U401
62
H-DY
EEPROM G2
U702 Horizontal Driver High Voltage 2 G4
& Output Generator
T301, Q315, Q316 T302
PS1 PS2
BRIGHTNESS
CONTROL
80V Q329,Q323,VR304
Switch Power 47V Voltage 12V Dynamic Focus
AC Input 15V
Supply Regulator 5V Q302, Q303, Q304
7V
U101, T101 -12V
Q106, Q113 Q305, Q338, T303,
Q301, Q317
63
64