W

FOR TYPICAL REMOTE CONTROL

M 2
CIRCUIT DRAWN WITH POWER SUPPLY OFF
2 DETAILS, SEE DOCUMENT
3 V
4
1
3
3
PHASE
RWS100
SUPPLY
U
3 1
6

5 U V W E
FS1

C1 C2
U W X

SK2
0VAC 1
TRANSISTOR SWITCHING FOR
PS1
24VDC CONTACTORS (IQ10-35) 120VAC 4
RELAYS ONLY FITTED WHEN
0VDC
120VAC CONTACTOR IS FITTED 3 4
FOR IQ40,70,90,91 & 95 24VDC
24VDC 6
_ 5 NOMINAL SUPPLY

+
(OUTPUT)
SK14
0VDC 1

24VDC 2
SK13

26 WAY
REFER TO SHEET 2 FOR NOTES
& OPTION PCB'S IF FITTED

SK3 SK13 SK14

6 1 42
MONITOR RELAY
5 3 43
TORQUE 4 2 44
3
SK7
SENSOR 2
1 1 6
SK8
MAKE AT FULLY SHUT S1 8 7
POSITION 10 WAY 2 8
SENSOR MAKE AT FULLY OPEN S2 7 9 CONFIGURABLE FEEDBACK
3 10 SIGNALS FROM MOV
BATTERY - SK9 BREAK AT FULLY SHUT
4
S3 6 11
4 12
+ 1 BREAK AT FULLY OPEN S4 5 13
FS2 (IF FITTED) 100mA SK4
CLOSE 9 33
STOP/ MAINTAIN 10 34 COMMAND SIGNALS
50% SK6 OPEN 8 35 FROM PLC TO MOV

COMMON -VE 1 36
18 WAY
REMOTE
ESD 12 25
CLOSED

OPEN
STOP
OPEN INTERLOCK 13 37
LOCAL

CLOSE INTERLOCK 14 38
COMMON -VE 5 31
SK1 SK2
SLOT A SLOT B

Iss Date Chkd Revision Details IQ BASIC DIAGRAM

5 090113 PMJ Re-track of the 24V DC pin
of SK14 to behind the diode.
6 060614 PMJ 400v added to type 1 ROTORK CONTROLS LTD ROTORK CONTROLS INC Drawn by: PMJ Circuit Diagram Number Issue Sheet
Date : 160512 No
tapping Y. Note added to
sheet 2 note 1.
BATH, BA1 3JQ
ENGLAND
ROCHESTER
NY 14624, USA
Base WD: 100B0000
Job No : - -
100B0000 6
1
of 2
Tel:01225-733200 Tel:585-247-2304 MI No : - - B1 C1 B2 C2
IQ3
 CIRCUIT DRAWN WITH POWER SUPPLY OFF

NO
OPTIONS
FITTED

NOTES
1.FUSES:
-PS1 is a self-resetting fuse. 3.INDICATION:
-Refer to publication PUB002-039 for approved fuses FS1 and FS2. -For typical position, status and alarm indication see PUB002-041.
-Actuator rated voltage specified on nameplate. Voltage tolerance +/-10%, -“S” contacts are user configurable and are shown in their default
applies for rated torque performance; duty cycle is not gauaranteed. setting.
2.REMOTE CONTROL: -Refer to PUB002-040 for functions and configuration instructions.
-For typical remote control circuits refer to: -Monitor Relay indicates actuator availability for remote control (shown
-RWS indicated or PUB002-041. “unavailable”). It can be configured to exclude local/remote selection.
-For DC and AC control, connect –ve/0V to terminal 36. -Refer to PUB002-040 for monitored functions and configuration
-(For negative switch / positive common, refer to RWS indicated). instructions.
-Control signal threshold voltages: -Voltage applied to indication contacts must not exceed 150Vac
-DC: “on” ≥16Vdc / “off” ≤8Vdc, max 60Vdc. -Individual Switch current must not exceed 3.5A inductive, 5A resistive
-AC: “on” ≥60Vac / “off” ≤40Vac, max 120Vac. and no more than 8A in total for all 4 contacts.
-Control signal duration to be 300ms minimum. 4.BATTERY:
-Maximum current drawn from remote control signals is: -Battery maintains local and remote “S” contact indication only.
-8mA at 24Vdc or 12mA at 120Vac. -Refer to installation manual for approved replacement battery types.
-Supply provided on terminals 4 & 5:
-Intended for remote control. Issue Sheet
-Max external load 5W at 24Vdc / 5VA at 120Vac Circuit Diagram Number
100B0000 6
No
2
See Sheet 1 for all Revision details/information of 2
IQ3