REPLACEMENT PARTS

Item No. Part No. Description Qty

1 E111101 ColorTouch control box suite 1

2 E111107 ColorTouch electronic board 220V suite 1

2 E111108 ColorTouch electronic board 110V suite

3 510106781 Internal Plate 1

4 510116781 Bottom Plate 1

5 106176996 Power switch 1

6 E111102 Screw suite 1

7 04013004 Two-Core cable for output 2

7 105101306 Three-Core cable for input 1

8 106231416 Cable Gland 1

9 E111106 Switch for learn key suite 1

10 E111103 Mounting bracket suite 1

11 106697000 Remote(With Battery) 1

ColorTouch Control Box

INSTRUCTION MANUAL

Keep this Manual for futrue reference

8 EMLI20010341
 CONTENTS INSTALLATION
A) Remove the mounting bracket from the control box, position the mounting bracket
to the desired fitting place and mark on the wall with the location of the drilled holes.
WARNING ------------------------------------------------------ 3 B) Then drill 4 holes of ø8mm on the marked position and insert a plastic fitting, Secure the
mounting bracket by fastening 4 screws of M5x35 to the plastic fittings. Figure .
C) The ColorTouch control box is hanged on the hook of mounting bracket,and secure the
bottom screw.
PRODUCE DESCRIPTION ---------------------------------------- 3-4

Plastic Fitting
WIRING DIAGRAM ----------------------------------------------- 5
Mounting Bracket

CONTROLS INDEX ---------------------------------------------- 5-6

M5*35 Screw
INSTALLATION -------------------------------------------------- 7

MAINTENANCE AND TROUBLE SHOOTING -------------------------- 7

MAINTENANCE AND TROUBLE SHOOTING
1) Do not leave the ColorTouch control box directly under sunlight.
REPLACEMENT PARTS ------------------------------------------- 8
2) Before switching on the control box, check the circuit boxes are running properly.
3) Warranty will be voided if the Emaux ColorTouch control box was dismantled by
unauthorized personnel.

Trouble Possible Solution

Touch remote and Display Replace battery CR2032.May enter water to

Light out. damage remote.

The display Light up on the remote

The remote is relearned by the learn key of
and pool light up,but not control
control box.
lights.

The control box works normally, Check transformer.

but pool light out. Replace pool light panel.

Check main power button.

Check connected locations of the cable.
The ColorTouch box is not work.
Check fuses at switchboard.
Contact qualified electrcian to test.

2 7
2) ColorTouch Remote WARNING
Each control box is associated with a ColorTouch remote control. You would need to have
control box nearby the ColorTouch remote. Please read the manual carefully before commencing installation. This manual contains important
· Learning process of remote: switch off main power button of the box before pressing the learn information about the correct operation of ColorTouch control box.
key of box. Then switch on main power button and pressing the learn key of the box,the
Learn key display is flash white.while keep pressing learn key of box,pressing any key on
— Before
the ColorTouch remote. When success link, the display on the remote is red momently and Learn
key display of box is out .
· This ColorTouch control box must be installed by a licensed or certified electrician or a
qualified serviceman in accordance to the requirements of your government standard or
· If there is one remote for multiple control box, repeat the learning process to each control
local authorities. Improper installation will create electric hazards which could result in
box.
serious injury, death as well as damage to the property.
· Cut the power before service and maintainance!
The Remote has two control modes:
· For safe and proper installation, ensure that those parts supplied with the
A) E-Lumen X mode-It is the default control mode after learning.
produceare used.
· The display LED under at the center of color wheel will be flashed in red
· Never handle with wet hands and feet.
color for any touch command on the remote.
· If the external flexible cable or cord of this ColorTouch control box is damaged, it shall be
· The ColorTouch remote choose direct color pick up just by tocuh the color
exclusively replaced by the manufacturer or his service agent or a similar qualified person in
area.
order to avoid a hazard.
· The rainbow color key is a toggle key for multiple modes of auto color
change . · Preferably installed in the place sheltered from rain or sunlight, ensure the longevity of
· There are three level of brightness for light brightness adjustment by these ColorTouch control box.
touch the desired brightness button.
· Z1, Z2 and ALL are ON/OFF switch to ON/OFF Zone 1, Zone 2 and both
Zones. The Reset key will turn Z1 and Z2 lights back to Cool White. It will
take three seconds to the light up after switch off. PRODUCT DESCRIPTION
· Touch any key three seconds to display Light ON/OFF.
— SPECIFICATIONS

B) E-Lumen Mode
· Long touch reset button will change the ColorTouch remote to E- Work Temperature 0-40℃
Lumen mode,the display LED at the center of color wheel will turn to
green color flash. Input Voltage AC220-240V(110V), 50/60Hz
· The color wheel buttons and brightness function is disable.
Output Voltage 2*AC220-240V(110V), 50/60Hz
· Touch Z1, Z2 and all button will change the Zone 1, Zone 2 or Both
Zones color one by one. Reset button will turn all the light color to first Maximum Power Rating 2*300VA
E-Lumen color.
Radio Frequency 433MHz
Attention:
Radio Distance At Sight(Empty area) 50m
(1) Battery replacement-reverse the remote and open the battery
compartment by pushing the right hand side lock inward. The remote Remote Battery CR2032
use CR2032 battery that life time is around six months.
(2) E-Lumen X mode or E-Lumen mode,must switch off main power button
of the box , wait three minutes and switch on it.

6 3
— CONTROL BOX DISPLAY AND FUNCTION KEYS WIRING DIAGRAM
Input
AC 220-240V(110V)

Reset Button
Learn Key Display
All Button

Z2 Button Standby ON/OFF Button Z2 Input Z1

220-240V(110V) 220-240V(110V)
Z1 Button

Main Power Switch

Transformer Transformer
AC 12V-32V AC 12V-32V

Power Cord Z2 Output Z1 Output Learn Key

E-Lumen X E-Lumen X

Attention:
— REMOTE FUCTION 1) Load of the control box should not exceed 2*300W.
2) The control box out voltage is 220~240Vac(110Vac) same as the power socket, it must be
connected to 12V-32Vac step down over transformers.
3) Please refer to the lamp power rating to choose adequate power rating transformer.

Color Wheel CONTROLS INDEX

Display
1) control box panel operation
· switch on the main power switch to turn on the power, the standby
button led will light up.
Brightness · press the standby button, ands the system is entered to operation mode.
· Z1 Button - long press ( 3 second) to switch ON / OFF Z1 power. And
short press (1 second) to change color for all the pool lights,
All
Z2 connected to the Z1 outlet, the Z1 Button LED is flash at the monment.
Z1 · Z2 Button - long press ( 3 second) to switch ON / OFF Z2 power. And
RESET short press (1 second) to change color for all the pool lights,
connected to the Z2 outlet, the Z2 Button LED is flash at the monment.
· ALL Button - Long or short press to change color for all the pool lights, connected to the Z1 and Z2
outlet, the ALL Button LED is flash at the monment.
Battery · RESET Button - Press the button to reset all the pool lights connected to Z1 & Z1 to cool white color.

4 5