Sub-218 Refeseries

rence
Introduction

The D.A.S. Sub-218 is a bass-reflex

subwoofer system for use in active systems
where bass reinforcement is required.

Applications

The Sub-218 is designed for applications

where high sound pressure levels of bass
frequencies are required such as sound
reinforcement in dance clubs.

Description
The Sub-218 houses two D.A.S. G-45 18"
cone transducer configured as a direct
radiators. This long excursion driver features
a 4" edgewound coil, massive magnet
structure and carefully engineered cooling
scheme, resulting in high power handling
and low power compression.

The ultra-compact enclosure is

manufactured from Wisa Birch plywood

and is finished with a hard wearing

catalyzed polyurethane paint that permits
color adaptations and provides weather
FEATURES resistance. 16 integrated rigging points that
accept 10M forged steel eyebolts make
» Direct radiator subwoofer suspension in either the horizontal or vertical
positions safe and simple. Loudspeaker
» 2 x 18" low frequency speakers components are protected by a heavy-duty
» 1200 W power handling steel grille sealed against corrosion using a
poliamide powder coat finish.
» Rugged steel grille
SPECIFICATIONS Placement

RMS (Average) Power HandlingR: 1200 W As with any bass unit, the Sub-218’s low
Program Power HandlingP: 2400 W frequency output will benefit from placement
Peak Power HandlingK: 4800 W against walls and/or floors.
On-axis Frequency RangeF: 35 Hz - 3.3 kHz
Usable Frequency Range: 35 Hz - 1 kHz
Nominal Impedance: 4Ω
Minimum ImpedanceI: 3.8 Ω (at 44 Hz)
On-axis Sensitivity 1W / 1 mS: 101 dB SPL
Rated Peak SPL at Full Power: 138 dB SPL at 1m
Nominal -6 dB BeamwidthsB: 360° Horizontal
(100 Hz octave) 360° Vertical
1120

Enclosure Material: Wisa Birch plywood

Finish: Black catalyzed polyurethane paint
Transducers/Replacement Parts: G-45/GM G-45
Connector: 2 paralleled NL4 Speakon, wired to ±1
Dimensions (H x W x D): 112 x 55 x 48 cm 43

(44 x 21.7 x 18.9 in)

550
Weight: 59 kg 224 128

(130 lbs)
Shipping Weight: 63.8 kg 37
480

(140.4 lbs)
256

ALL DIMENSIONS IN MILIMETERS

112

R Corresponds to the AES power handling rating for the component, based on a 2 hour test using a 6 dB crest factor bandlimited pink noise
signal.
P Conventionally 3 dB higher than the RMS measure, although this already utilizes a program signal.
K Corresponds to the signal crests for the test described inR.
F As per IEC 268-5 (1989), re. a one octave band centred at 500 Hz. Half space anechoic.
I In practice cable and connector impedance has to be added to all impedance values.
S For the 250 Hz one octave band.
B Average of one-third octave band measures.
One and one-third octave bands comply to ANSI S1.11-1986.
Sub-218
Frequency Response
Figure 1 shows the frequency response at 1 m
of a unit radiating to a half space anechoic envi-
ronment and driven by a 1 W (2 V) swept sine
signal.

Impedance
Figure 2 shows impedance with frequency.

Distortion
Figure 3 shows the Second Harmonic Distortion
(grey) and Third Harmonic Distortion (dotted)
curves for a unit driven at 10% of its nominal
power handling rating.

Beamwidth
Figure 4 shows the -3, -6 and -10 dB horizontal
(solid) and vertical (dashed) beamwidth with
frequency curves. -6 dB ones are shown with
thicker traces for clarity.

Axial Directivity Q(Rθ) and Di

Figure 5 shows the above characteristics with
frequency. Thin continuous and dashed lines
show partial horizontal and vertical,
respectively, characteristics.

Polar Response
Figure 6 shows the one octave band horizontal
(solid) and vertical (dashed) polars for the
indicated frequencies. Full scale is 50 dB, 5 dB
per division.
NOTES. 1.Frequency response: referred to 1 m; low end
obtained through the use of near field techniques; one-third
octave smoothed for correlation with human hearing. 2.In
practice, cable and connector impedance need to be added.
3.Low frequency near-field techniques used. 4.Directivity
characteristics plotted with respect to frequency are the
average within the one-third octave bands of center
frequencies noted by the marks at the bottom of the graphs,
but are joined up for display purposes. Interpolation was
used below 100 Hz. All other characteristics plotted vs.
frequency use 1/24th octave resolution. Regions of less than
1 dB below goal level and sharp notches may be ignored
when calculating beamwidths. 5.Directivity factor and index
were computed from two degree resolution vertical and
horizontal polars using sinusoidal weighting. 6.Polars were
acquired by placing the unit on a computer controlled
turntable inside our anechoic chamber. Measurement
distance was 4 m.

Product improvement through research and development is

a continuous process at D.A.S. Audio. All specifications
subject to change without notice.

TE/035-03

D.A.S. Audio, S.A.

07/00

C/. Islas Baleares, 24 - 46988 Fuente del Jarro - Valencia, SPAIN

Tel. 96 134 0525 - Tel. Intl. +34 96 134 0860 - Fax. 96 134 0607 - Fax. Intl. +34 96 134 06 07
D.A.S. Audio of
America, Inc. 6970 N.W. 50th St. Miami, FL 33166, U.S.A.
Tel. +1 305 436 0521 - Fax. +1 305 436 0528
http://www.dasaudio.com