Service.

Self-Study Programme 304

Electronic Diesel Control EDC 16

Design and Function

ProCarManuals.com
 The new EDC 16 engine management system With EDC 16 electronic diesel control, an engine
from Bosch has its debut in the management system has been made available
V10-TDI- and R5-TDI-engines. that meets these demands. This has been achie-
Increasing demands on today's diesel engines in ved above all by the greatly improved proces-
terms of comfort, fuel consumption, exhaust sing performance of the engine control unit and
emissions and road handling, mean greater a new signal processing system.
complexity in the hardware and software of
engine management systems.
ProCarManuals.com

304_065

In this Self-Study Programme, you will be made familiar with the EDC 16 engine management
system, using the V10-TDI-engine as an example. Your attention will be drawn to changes
between the V10-TDI- and R5-TDI-engines.

NEW Important
Note

This Self-Study Programme explains the design and For the latest testing, adjusting and repair
function of new developments. instructions, please refer to the relevant workshop
The contents will not be updated. literature.

2
 Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Engine management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

V10-TDI-engine system overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Metering regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Start of injection regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Exhaust gas recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Charge pressure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preglow system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Idling speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Smooth running control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Active pulse damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cruise control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ProCarManuals.com

V10-TDI-engine functional diagram . . . . . . . . . . . . . . . . . . . . . . . 44

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Workshop equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

3
 Introduction

Bosch EDC 16

Bosch EDC 16 is a torque-orientated engine management system which is featured for the first time in a
diesel engine. As is the case with petrol engines, in the EDC 16 system all torque demands are collected,
evaluated and co-ordinated in the engine control unit. This has the advantage of better adaptability
between the individual vehicle systems (engine management, brake system, automatic gearbox, air
conditioning, ...).

Internal torque demands

Engine control unit J...
– Start
– Idling speed control
– Full throttle
– Power limitation
– Speed governor
ProCarManuals.com

– Driving comfort
– Component protection

External torque demands Realisation of torque demands

EGR valve N18

Accelerator pedal module

Cruise control system Unit injector solenoid valves N240 … 244

Automatic gearbox
control unit J217

Turbocharger 1 positioning motor V280

ABS with ESP control unit J104

Turbocharger 2 positioning motor V281

Climatronic control unit J255

304_062
4
 The Bosch EDC 16 engine management system is designed to be compatible as both a single and double
control unit concept. The actual concept used depends on the number of cylinders in the engine.

– On the R5-TDI-engine, engine control unit 1 J623 fulfils all functions.

– On the V10-TDI-engine, engine control unit 1 J623 fulfils the basic functions for cylinder bank 1 and
engine control unit 2 J624 for cylinder bank 2. Basic functions are, for example, actuation of the unit
solenoid injector valves and exhaust gas recirculation.

Functions that cover whole cylinder banks, such Information received by engine control
as the coolant supply, are carried out by unit 1 J623 is sent to engine control unit 2 J624
engine control unit 1 J623, or the smooth running via an internal CAN databus.
control by engine control unit 2 J624.
ProCarManuals.com

Engine control
Engine control
unit 1 J623
unit 2 J624
Both control units are identical and
have the same part number.
The allocation of engine control unit 1
and engine control unit 2 is done via a
coding link in the connector for engine
control unit 2. Following allocation,
the control units can no longer be
changed over.
304_071

Engine control units in the CAN drive train databus

Engine control Control unit Turbocharger 1 Automatic Entry and start

unit 1 J623 for ABS with positioning gearbox control authorisation
ESP J104 motor V280 unit J217 control unit J518
Internal CAN
databus

Engine control Steering column Turbocharger 2 Airbag control Control unit

with display in
unit 2 J624 electronics positioning unit J234 dash panel
control unit J527 motor V281 insert J285 304_026

5
 Engine management

System overview for V10-TDI-engine

Sensors Actuators
Altitude sensor
Engine speed sender G28
Engine control unit 1 J623

Unit injector solenoid valves N240 ... N244

Accelerator pedal position sender G79

Kick-down switch F8
Idle switch F60
Exhaust gas recirculation valve N18
Turbocharger 1 positioning motor V280

Air mass meter G70

Intake manifold flap motor V157
Control unit for ABS with ESP J104

Engine speed
Automatic gearbox control unit J217
Hall sender G40
ProCarManuals.com

Control unit for display in dash panel insert J285

EGR cooler changeover
Lambda probe G39 Diagnosis connection Airbag control unit J234
. valve N345
.
.
Fuel pump relay J17
Coolant temperature sender G62 Turbocharger 2 positioning motor V281 Fuel pump (presupply pump) G6
Fuel pump G23

Thermostat for map-controlled

Coolant temperature sender
engine cooling F265
radiator outlet G83
Engine control unit 2 J624
Additional coolant pump relay J496
Unit injector solenoid valves Continued coolant circulation pump V51
Fuel temperature sender G81 N245, N303 ... N306

Air mass meter 2 G246 Fuel cooling pump relay J445

Exhaust gas recirculation valve 2 N213 Fuel cooling pump V166
Charge pressure sender G31
Intake air temperature sender G42
Lambda probe 2 G108 Right solenoid valve for electro-hydraulic
engine mounting N145
Intake manifold flap motor 2 V275
Brake light switch F
Brake pedal switch F47 Intake air temperature sender 2 G299
EGR cooler changeover Lambda probe heating Z19
Charge pressure sender 2 G447
valve 2 N381

Fuel composition
Fuel temperature sender 2 G248 Glow plug relay J52
sender G133 Lambda probe heating 2 Z28
Glow plugs Q10 ... Q14

Glow plug relay 2 J495

Additional input signals Additional output signals
Glow plugs Q15 ... Q19
6 304_003 7
Engine management

System overview for V10-TDI-engine

Sensors Actuators
Altitude sensor
Engine speed sender G28
Engine control unit 1 J623

Unit injector solenoid valves N240 ... N244

Accelerator pedal position sender G79

Kick-down switch F8
Idle switch F60
Exhaust gas recirculation valve N18
Turbocharger 1 positioning motor V280

Air mass meter G70

Intake manifold flap motor V157
Control unit for ABS with ESP J104

Engine speed
Automatic gearbox control unit J217
Hall sender G40

ProCarManuals.com
Control unit for display in dash panel insert J285
EGR cooler changeover
Lambda probe G39 Diagnosis connection Airbag control unit J234
. valve N345
.
.
Fuel pump relay J17
Coolant temperature sender G62 Turbocharger 2 positioning motor V281 Fuel pump (presupply pump) G6
Fuel pump G23

Thermostat for map-controlled

Coolant temperature sender
engine cooling F265
radiator outlet G83
Engine control unit 2 J624
Additional coolant pump relay J496
Unit injector solenoid valves Continued coolant circulation pump V51
Fuel temperature sender G81 N245, N303 ... N306

Air mass meter 2 G246 Fuel cooling pump relay J445

Exhaust gas recirculation valve 2 N213 Fuel cooling pump V166
Charge pressure sender G31
Intake air temperature sender G42
Lambda probe 2 G108 Right solenoid valve for electro-hydraulic
engine mounting N145
Intake manifold flap motor 2 V275
Brake light switch F
Brake pedal switch F47 Intake air temperature sender 2 G299
EGR cooler changeover Lambda probe heating Z19
Charge pressure sender 2 G447
valve 2 N381

Fuel composition
Fuel temperature sender 2 G248 Glow plug relay J52
sender G133 Lambda probe heating 2 Z28
Glow plugs Q10 ... Q14

Glow plug relay 2 J495

Additional input signals Additional output signals
Glow plugs Q15 ... Q19
6 304_003 7
 Engine management

Metering regulation

The quantity of fuel injected influences important engine properties, such as the torque,
output, fuel consumption, exhaust gas emissions and mechanical and thermal stress
of the engine.
Thanks to the metering regulation, the engine can operate in all working conditions with optimal fuel
combustion.

G79
F8
J624 J623
F60
G70

G42
ProCarManuals.com

N240 … 244

G62
G81

G28

304_079

F8 Kick-down switch G81 Fuel temperature sender

F60 Idle switch J623 Engine control unit 1 (cylinder bank 1)
G28 Engine speed sender J624 Engine control unit 2 (cylinder bank 2)
G42 Intake air temperature sender N240 Unit injector solenoid valves, cylinders 1 - 5,
G62 Coolant temperature sender … N244 cylinder bank 1
G70 Air-mass flow meter
G79 Accelerator pedal position sender A Altitude sensor

Air intake, normal Input signal

Air intake, compressed Output signal

Exhaust gas CAN drive train databus

8
 This is how it works:

The specified torque is calculated from the internal and external torque demands. To reach this torque
specification, a set quantity of fuel is required.

The quantity of fuel, for example, is calculated by the engine control unit with respect to

– the driver's requirements,

– the engine speed,
– the amount of air drawn,
– the coolant temperature,
– the fuel temperature and
– the intake air temperature.

However, to protect the engine against mechanical damage and to prevent black smoke, there should be
ProCarManuals.com

limitations on the quantity of fuel injected. For this reason, the engine control unit calculates a limit value
for this quantity.

The limit value depends on

– the engine speed,

– the air mass and
– the air pressure.

The parts systems illustrated as follows in this Self-Study Programme are based on the
V10-TDI-engine as fitted in the Phaeton.
As can already be seen in the illustrated overview, reference is made only to cylinder bank 1
for description of the systems. Likewise, only the components belonging to the relevant parts
system are included in the key.

9
 Engine management

Start of injection regulation

The start of injection regulation influences a number of engine properties, such as the engine
performance, the fuel consumption, the noise emissions and, equally as important, the exhaust
emissions.
The start of injection regulation thus has the task of determining the correct point of fuel delivery and
injection.

This is how it works:

The engine control unit calculates the start of

injection.

The specification depends on Further influencing factors are

– the engine speed and – the coolant temperature and

– the calculated quantity of fuel to be injected – the air pressure.
ProCarManuals.com

from the metering regulation.

G28 Engine speed sender

A G42 Intake air temperature sender
G62 Coolant temperature sender
J623 Engine control unit 1
J624 J623
J624 Engine control unit 2
N240 Unit injector solenoid valves, cylinders 1 - 5
G42
… N244
BIP
IM

A Altitude sensor
t

N240 … 244

Air intake, normal

G62
Air intake, compressed

Exhaust gas

G28 Input signal

304_073 Output signal

CAN drive train databus

10
 In order that the start of delivery can be
calculated optimally, the actual point at which
delivery begins must also be registered. Current pattern - Unit injector solenoid valve

To do this, the engine control unit monitors the

flow at the unit injector solenoid valve. From the BIP Holding current
special flow pattern, the actual start of delivery, IM
and thereby the start of injection, is determined.

Control limit

This is how it works:

ProCarManuals.com

Start of injection is initiated when the unit injector Pickup current

solenoid valve is actuated. For actuation, a
304_072
magnetic field is created, current increases and
the valve shuts. t
When the valve shuts on the valve seat, a
Start of valve actuation End of valve actuation
distinctive jolt is noticeable in the current flow.
This is known as COI (Commencement Of
Injection period).
COI signalises complete closure of the unit IM – Solenoid valve current
injector solenoid valve and thereby the point of t – Time
delivery. The signal is received by the engine COI (BIP) – Point at which valve shuts
control unit.

If the valve is closed, current is maintained at a

constant level. Once the required period of
delivery has elapsed, actuation will cease and
the valve will open. In order that faults can be detected at the
solenoid valve, the engine control unit evaluates
The actual moment at which the unit injector the COI position from the current flow pattern. If
solenoid valve closes, that is COI, is determined there are no faults, COI will be within the control
so that the point of actuation for the next limit. If this is not the case, the valve is faulty.
injection period can be calculated.
Effects of signal loss
If the actual COI deviates from the mapped
details stored in the engine control unit, the If faults are detected at the solenoid valve, start
engine control unit will correct the point of valve of delivery is determined based on fixed values
actuation. from the map. Regulation is no longer possible
and performance will be impaired.

11
 Engine management

Exhaust gas recirculation

Exhaust gas recirculation means that some of the exhaust emissions from the combustion process are
used again. Because the exhaust gases contain very little oxygen, the peak combustion temperature is
lowered and nitrogen oxide emissions (NOX) are reduced.
Exhaust gas recirculation occurs up to an engine speed of approximately 3000 rpm.

N345
J624 J623
N18
G70
V157
ProCarManuals.com

F E I

H
C
N240 … 244
B
D
G62

G
G28 G39

304_044

G28 Engine speed sender A Altitude sensor

G39 Lambda probe B EGR cooler
G62 Coolant temperature sender (V10-TDI-engine, Phaeton)
G70 Air mass meter C EGR changeover flap
J623 Engine control unit 1 D Vacuum unit
J624 Engine control unit 2 E Intake manifold flap
N18 Exhaust gas recirculation valve F EGR valve
N240 Unit injector solenoid valve, cylinders 1 - 5 G Starter catalyst
… N244 H Vacuum pump
N345 EGR cooler changeover valve I Charged air cooler
V157 Intake manifold flap motor

12
 This is how it works:

The amount of recirculated exhaust gas will always depend on the engine speed, the amount of fuel
injected, the amount of air drawn in, the intake air temperature and the air pressure.

Lambda regulation for exhaust gas recirculation

(V10-TDI-engine)

On the V10-TDI-engine, the amount of – If the oxygen content is too high, the amount
recirculated exhaust gas is corrected by Lambda of recirculated exhaust gas is increased.
regulation. With this system, the remaining oxygen
content in the exhaust gas is calculated and the – If the oxygen content is too low, the amount of
figure is sent to the engine control unit. If the recirculated exhaust gas is lowered.
ProCarManuals.com

actual oxygen content deviates from the specified

figure, the engine control unit actuates the exhaust
gas recirculation valve N18 and increases or
decreases the amount of recirculated exhaust gas.
With Lambda regulation, the amount of
recirculated exhaust gas can be determined
precisely.

Exhaust gas recirculation control

(R5-TDI-engine)

On the R5-TDI-engine, the amount of recircula- If the air mass drawn in deviates from the
ted exhaust gas is stored in a map in the engine specified figure, the amount of recirculated
control unit. It contains a value for the necessary exhaust gas is adjusted respectively.
amount of fresh air for every operating situation.

Air intake, normal Input signal

Air intake, compressed Output signal

Exhaust gas, not cooled CAN drive train databus

Exhaust gas, cooled

Coolant

Vacuum

13
 Engine management

Exhaust gas recirculation cooling

The V10-TDI-engine in the Phaeton has an independent cooler for exhaust gas recirculation
for each cylinder bank due to its emissions classification. The system cools the recirculated exhaust gas
when the coolant temperature exceeds 50 oC.

This has two advantages:

– The combustion temperature is reduced and

– A greater amount of exhaust gases can be recirculated.

This means that there is less nitrogen oxide and the build up of carbon is reduced.

This is how it works:

An independent exhaust gas recirculation cooler is used because continual cooling of the recirculated
exhaust gas lengthens the period required for the engine to reach optimal operating temperature and
ProCarManuals.com

leads to an increase in carbon dioxide and carbon monoxide emissions. For the independent cooling pro-
cess, the exhaust gas is directed either past or through the cooler to the exhaust gas recirculation valve.

Without exhaust gas cooling With exhaust gas cooling

Up to a coolant temperature of 50 oC, the From a coolant temperature of 50 oC, the

exhaust gas flap remains closed and the exhaust exhaust gas flap is opened by the changeover
gas is directed past the cooler. valve. The recirculated exhaust gas will now flow
past the cooler. The cooler output depends on
the coolant temperature and the amount of
recirculated exhaust gas.

From coolant temperature Exhaust gas recirculation

Engine control sender G62 cooler changeover valve N345
unit 1 J623

Vacuum unit,
To exhaust gas Vacuum unit, not
actuated
recirculation valve actuated

Exhaust gas flap

Cooler for exhaust

gas recirculation To exhaust gas
turbocharger
From exhaust
manifold

304_063 304_064

14
 Charge pressure control

The charge pressure is controlled by a map that is stored in the engine control unit.

This is how it works:

The engine control unit sends a signal via the Charge pressure control works depending on the
CAN drive train databus to the turbocharger torque demand. To control the charge pressure,
positioning motors. The signal will read between signals from the charge pressure sender are
0 and 100 % and is the value required for the used.
guide vane setting. The positioning motor will The signals from the intake air temperature
adjust the position of the turbocharger guide sender, coolant temperature sender and the
vanes respectively and speed changes will result altitude sensor are used as correction factors.
from the different angles. The charge pressure The charge pressure is reduced gradually when
will be increased or reduced. the vehicle is travelling at high altitudes to
protect the charger.
ProCarManuals.com

Air intake, normal

J624 J623
G31 G70 Air intake, compressed
G42
Exhaust gas

B Input signal

Output signal
N240 … 244
CAN drive train databus

G62

V280
C

304_045

G31 Charge pressure sender N240 Unit injector solenoid valves, cylinder 1 - 5
G42 Intake air temperature sender … N244
G62 Coolant temperature sender V280 Turbocharger 1 positioning motor
G70 Air mass meter
J623 Engine control unit 1 A Altitude sensor
J624 Engine control unit 2 B Charged air cooler
C Turbocharger
15
 Engine management

Preglow system

The preglow system makes it easier to start the engine at low outside temperatures.
It is activated by the engine control unit at coolant temperatures below +9 oC.
The glow plug relay is actuated by the engine control unit. Once actuated it provides
the current required for the glow plugs.

Engine control unit 1 J623 Engine control unit 2 J624

ProCarManuals.com

CAN drive train databus

Engine speed Glow plug relay J52

sender G28 Glow plugs Q10 … Q14

Glow plug relay 2 J495

Glow plugs Q15 … Q19

Coolant temperature Preglow warning

sender G62 lamp K29

304_043

Preglow period Extended glow period

The glow plugs are activated when the ignition is Once the engine starts, there is an extended
switched on and outside temperature is below glow period. This helps to lower the combustion
+9 oC. The preglow warning lamp will light up. noise, it improves the idling speed quality
Once the glow period has elapsed, the warning and the carbon dioxide emissions are reduced.
lamp will go out and the engine can be started. The extended glow period lasts for a maximum
of four minutes and is deactivated at engine
speeds at above 2500 rpm.
There is no extended glow period if, for example,
the battery voltage is too low.

16
 Idling speed control

Idling speed control means a specified speed is This is how it works:

set before the accelerator pedal is applied. This
is then adapted to the currently active operating The specified speed is regulated by a map in the
condition of the engine. engine control unit. The map draws on
Therefore, a cold engine will have a higher idling information
speed than a warm engine. Furthermore, other
performance demands are considered such as – from the coolant temperature sender,
– the load on the alternator and
– the large amount of energy drawn by the – the load on the vehicle electrical system.
alternator when the electrical system has low
power, the power-assisted steering pump, The engine control unit continually adapts the
– the high level of pressure required for diesel amount of fuel injected until the actual speed
injection, equates to the specified value.
– the energy required to overcome the internal
friction of the engine and To avoid unnecessary emissions, the idling speed
ProCarManuals.com

– from the torque converter at different loads. is kept to a minimum level, though during this
process, demands on smooth running also play a
role.

Engine control unit 1 J623 Engine control unit 2 J624

Accelerator pedal position

sender G79
Idle switch F60

Engine speed Unit injector solenoid

sender G28 valves N245, N303 … 306

Coolant temperature
sender G62

Alternator load (DFM signal)

Unit injector solenoid
304_074
valves N240 … 244
Additional requirements

17
 Engine management

Smooth running control

Smooth running control improves engine running The effects of these differences in torque are
at idling speed.
– imbalanced engine running and
Different cylinders in an engine can often – an increase in exhaust gas emissions.
generate different levels of torque even though
the same amount of fuel has been injected. The smooth running control is designed to detect
Possible causes of this are, among other things, the pulses in speed that are caused as a result.
differences in The pulses in speed are then balanced by
targeted control of the amount injected at the
– the tolerances of the parts, affected cylinders.
– cylinder compressions,
– friction caused by the cylinders and
– the hydraulic injector components.
ProCarManuals.com

Example: Necessary changes in the amount of fuel injected at specified speeds of 580 rpm

304_058
Actual speed Change in quantity of fuel injected

This is how it works:

Detection works at idling speed via a signal from And in the same way, a cylinder that performs
the engine speed sender. better than the others will have a shorter path.
If the signals are received in a balanced rhythm, If the engine control unit detects a deviation, the
the cylinders are all working the same way. affected cylinder will receive a smaller or greater
If one cylinder performance is less than the amount of fuel until the engine runs smoothly
others, the crankshaft needs longer to reach the again.
next point of ignition.

18
 Active pulse damping

With the active pulse damping system, there is a reduction in jolt-type vehicle movements
that are generated by load changes from different acceleration requirements.

Without active pulse damping With active pulse damping

When the accelerator pedal is depressed, a When the accelerator pedal is depressed, the
large amount of fuel (blue curve) is injected for a amount of fuel injected (blue curve) is not the full
brief period. amount demanded at the start. Instead it is
delayed half way.
This sudden load change can lead to pulsations If there are pulsations in the vehicle drive train,
(red curve) in the vehicle drive train due to strong these will be detected through evaluation of the
changes in engine torque. engine speed signal. When speed increases, the
amount of fuel injected is reduced and likewise
These pulsations are perceived as uncomfortable when speed decreases, fuel is increased.
ProCarManuals.com

changes in acceleration by the occupants of the

vehicle. These damped pulsations (red curve) are less
noticeable by the occupants of the vehicle.

Without active pulse damping With active pulse damping

1000
n (1/min)

n (1/min)

1000
V (mm3)

V (mm3)
25 25

800 20 800 20

12 12

0 1 2 304_053 0 1 2
304_054
t (s) t (s)

n – Engine speed
t – Time
V – Amount of fuel injected

When the clutch is depressed, active

pulse damping is switched off. In this
way, a quicker response from the
engine is achieved.

19
 Engine management

Governor

The governor protects the engine from overrevving and thereby from damage. The engine is therefore
governed to a maximum permissible speed that cannot be exceeded for long periods of time.

This is how it works:

After regulation has started, the amount of fuel The adaptive function is kept as smooth as
injected is continually reduced. possible in order that jolts in the amount of fuel
If the highest permitted engine speed is reached, injected are not caused during acceleration.
the amount of fuel injected remains constant until
the driving conditions change again.
ProCarManuals.com

Maximum speed
Start of regulation
1/min

Engine control unit 1 J623 Engine control unit 2 J624

t

Unit injector solenoid

valves N245, N303 … 306
Engine speed sender G28

304_069
Unit injector solenoid
valves N240 … 244

20
 Cruise control

The Cruise Control System (CCS) allows the vehicle to be driven at a constant speed without the driver
having to press the accelerator pedal.

The start of cruise control depends on the vehicle. Cruise control on the Touareg, for example,
starts in the reduction gear at 6 km/h and in normal operation at 20 km/h. On the Phaeton, it starts
at 20 km/h.

This is how it works:

The specified speed is set via a button on the The engine control units adapt the amount of fuel
multi-function steering wheel. The signal is sent to injected so that the actual speed is the same as
engine control unit 1 J623 and passed on to the specified speed.
engine control unit 2 J624 via an internal CAN
ProCarManuals.com

databus.

Engine control unit 1 J623 Engine control unit 2 J624

Brake light switch F

Brake pedal switch F47
Unit injector solenoid valves N245, N303 … 306
Accelerator pedal position sender G79
Control unit with
display in dash panel
insert J285

Airbag control
Engine speed sender G28
unit J234

Multi-function steering wheel

with CCS operator buttons
Control unit for ABS
with ESP J104

304_066
Unit injector solenoid
valves N240 … 244

21
 Engine management

Sensors

Engine speed sender G28

The engine speed sender is bolted to the side of

the cylinder block. It picks up the position of the
crankshaft via a 60–2 ratio sender wheel.

Signal application

The engine speed sensor signal is used to

determine the speed of the engine and the
precise position of the crankshaft. With this
information, the amount of fuel injected and start
of injection is calculated.

Effects of signal loss

ProCarManuals.com

304_008
In the case of signal loss, the engine will switch
Engine speed
off and cannot be restarted.
sender G28

The signal from the engine speed sender is sent to engine control unit 1.
In order that engine control unit 2 can receive the engine speed at the same time, the signal is
also sent via a separate cable from engine control unit 1 to engine control unit 2.

Engine speed
sensor wheel

304_059

Reference point Engine speed

sender G28

22
 Hall sender G40
Hall sender G40

The Hall sender is bolted to the cylinder head at

cylinder bank 1 below the mechanical fuel pump. It
picks up the signal from the quick start sender
wheel with which the position of the camshaft is
detected.

Signal application

With the Hall sender signal, the relation of the

camshaft to the crankshaft is picked up very
quickly when the engine is started. Together with
the signal from the engine speed sensor G28, the
system can detect which cylinder is at TDC.
ProCarManuals.com

Effects of signal loss

If the signal fails, the signal from the engine speed

sender G28 is used in its place. Because the
304_007
position of the camshaft and the cylinders cannot
be detected immediately, starting of the engine
could take slightly longer than normal. On the V10-TDI-engine, just one Hall
sender is installed. However, the signal
is sent to both engine control units.

Hall sender G40

Quick start sender wheel

304_020

23
 Engine management

Accelerator pedal position sender G79,

Kick-down switch F8, Idle switch F60

The accelerator pedal position sender, the idle Accelerator pedal position sender G79
switch and the kick-down switch can be found in Kick-down switch F8
an accelerator pedal module on the pedal Idle switch F60
cluster.

Signal application

The accelerator pedal position sender G79

detects the position of the accelerator pedal
across the entire range. It is a main input signal
to calculate the amount of fuel to be injected.
ProCarManuals.com

The idle switch F60 detects when there is no

pressure on the accelerator pedal and activates
idling speed control.
304_017
The kick-down switch F8 sends a message to
the engine control unit when the accelerator
pedal is depressed fully. This information is sent
Accelerator pedal
by the engine control unit to the automatic gear-
position sender G79
box control unit and the kick-down function is
then activated.

Effects of signal loss

If the signal fails, the position of the accelerator

pedal will no longer be detected. The engine will
only run at increased idling speed and the glow
period warning lamp K29 will flash.
The driver can still reach the nearest workshop.
The engine should then be checked.

Kick-down switch F8

Idle switch F60

24
 Air mass meters G70 and G246 Intake manifold bridge
Air cleaner
Each cylinder bank has a hot film air mass meter
with backflow detection. It is installed in the
intake passage in front of the intake manifold
bridge.
The meters determine the actual air mass drawn
in for both cylinder banks.

Signal application

With these signals, the amount of fuel injected 304_060

Air mass meter G70
and the amount of recirculated exhaust gas for
each cylinder bank is calculated. Air mass meter 2 G246
ProCarManuals.com

Effects of signal loss

If the signal from the air mass meter fails, the

respective engine control unit operates using a
replacement value and exhaust gas recirculation
is switched off.

Lambda probes G39 and G108

(V10-TDI-engine)

Both broadband Lambda probes can be found

in the exhaust system in front of the starter
catalyst.
With these probes, the remaining oxygen content
in the exhaust gas is measured.

Signal application

With the signals from both Lambda probes, the

amount of recirculated exhaust gas is corrected.

Effects of signal loss

If the signals fail, the amount of recirculated

exhaust gas will be determined by the air mass
304_033
meter. Because this type of regulation is not Lambda Lambda
precise, the level of nitrogen oxide emissions probe 2 G108 probe G39
may rise.

25
 Engine management

Coolant temperature sender G62

The coolant temperature sender can be found in

the coolant connecting pipe between the cylinder
heads. It sends the coolant temperature to
engine control unit 1 J623.

Signal application

The coolant temperature is used by the engine

control units as a correction value to calculate
the amount of fuel to be injected, the charge
pressure, start of delivery and the amount of 304_035
recirculated exhaust gas, for example. In addi- Coolant connecting
tion, this information is used to regulate the coo- pipe Coolant temperature
ProCarManuals.com

lant temperature depending on the operating sender G62

conditions.

Effects of signal loss

If the signal fails, the engine control units use the

signals from the coolant temperature sender G83
and the fuel temperature senders G81 and G248.

Coolant temperature sender -

radiator outlet G83

The coolant temperature sender G83 can be

found in the line at the radiator outlet and it is
from this position that the coolant temperature is
measured.

Signal application

By comparing both signals from coolant tempe-

rature senders G62 and G83, the radiator fans
can be actuated.

Effects of signal loss

If the signal from coolant temperature 304_034

sender G83 fails, radiator fan output stage 1
Coolant temperature sender -
remains constantly active. Coolant temperature
radiator outlet G83
regulation is continued.

26
 Fuel temperature senders G81 and G248 Fuel filter module

The engine has a fuel temperature sender for

each cylinder bank. The senders can be found in
the return line to the fuel filter module on each
side. The senders are used to determine the fuel
temperature.

Signal application

The respective engine control unit calculates the

fuel density from the fuel temperature. This is
used as a correction value to calculate the
amount of fuel to be injected.
304_006
ProCarManuals.com

Effects of signal loss

Fuel temperature
If the signal fails, the relevant engine control unit sender 2 G248
will use a replacement value from the signal sent
by the coolant temperature sender G62. Fuel temperature
sender G81

The altitude sensor

The sender can be found in engine control unit 1 Altitude sensor Engine control unit 1 J623
J623 and is a permanent element of the control
unit.

Signal application

The signal is used to determine a correction

value for charge pressure control and exhaust
gas recirculation. If air pressure is lost, exhaust
gas recirculation will be switched off and charge
pressure increased. In this way, the same
304_039
performance at sea level is guaranteed at high
altitudes.

Effects of signal loss

If the signal fails, a replacement value is used.

At high altitudes black smoke could be the result.

27
 Engine management

Charge pressure sender G31,

Charge pressure sender 2 G447 and
Charge pressure sender 2 G447,
intake air temperature sender 2 G299
Intake air temperature sender G42,
Intake air temperature sender 2 G299

Charge pressure sender G31 and intake air

temperature sender G42 are integrated as one
component and can be found in the intake
manifold for cylinder bank 1.

Charge pressure sender 2 G447 and intake air

temperature sender 2 G299 are installed in the
intake manifold for cylinder bank 2. They are
also combined together to form one component.
ProCarManuals.com

304_024

Charge pressure senders G31 and G447 Intake air temperature senders G42 and G299

Signal application Signal application

The signals from the charge pressure senders are The signal from the intake air temperature senders
required to regulate and monitor the charge is required by the engine control units to calculate
pressure. a correction value for the charge pressure. When
The calculated value is compared by the the signal from these senders is evaluated, the
respective engine control units with the influence of the temperature on the density of the
specifications from the charge pressure maps. fuel is also considered.
If the actual value deviates from the specifica-
tion, the charge pressure is altered accordingly
by the engine control unit via the turbocharger
positioning motor.

Effects of signal loss Effects of signal loss

The charge pressure is controlled at an extremely If a signal fails, the engine control units will use a
low level to protect the engine from damage. fixed replacement value. The result could
Because of this, performance is impaired be impaired performance.
considerably.

28
 Brake light switch F and Brake pedal
switch F47

The brake light switch and the brake pedal switch

are part of one component and can be found on
Clutch pedal switch F36
the pedal cluster. Both switches send a signal to
engine control unit 1 when the brake is applied.
Brake pedal switch F and
brake pedal switch F47
Signal application

When the brake is applied, the cruise control

system is switched off.
If actuation of the accelerator pedal and the
brake pedal is detected, idling speed is
increased.
ProCarManuals.com

Effects of signal loss

If the signal fails from one of the senders, the

amount of fuel injected will be reduced and the
engine will have less output.
In addition, the cruise control system will be
switched off.

Clutch pedal switch F36 (manual gearbox)

The clutch pedal switch can be found on the

pedal cluster. The switch detects whether the 304_081
clutch is depressed or not.

Signal application

When the clutch is depressed, the amount of fuel

injected is reduced for a brief period to prevent
engine jolts during gear selection.

Effects of signal loss

If signal failure is encountered from the clutch

pedal switch, load jolts could become noticeable
from gear changes.
The cruise control system and active pulse
damping are no longer available.

29
 Engine management

Fuel composition sender G133

Fuel filter module
The fuel composition sender is bolted to the fuel
filter module and is engaged in the filter. The
sender detects excessive levels of water in the
fuel filter module and informs the engine control
unit.

304_082
ProCarManuals.com

Drainage connection to extract water

and fuel using hand vacuum pump
V.A.G 1390 and water drainage
container V.A.G 1390/1

Fuel filter module

304_047

Fuel composition
sender G133

Signal application

The signal from the sender prevents water from

entering the injection system and thereby
prevents corrosion.

30
 This is how it works:

A constant voltage is applied to the fuel composition sender by the engine control unit.

Contact pins
Water level OK Fuel

The contact pins are surrounded by diesel fuel.

Because diesel fuel has a low level of
450
conductivityconductivity, there is a high signal
response. In this way, the engine control unit V

detects that the water level is OK and sends the

information to the dash panel insert. The preglow
ProCarManuals.com

warning lamp K29 does not light up.

304_050
Water

Water level not OK

The contact pins are surrounded by water.

Because water has a high level of conductivity,
450
there is a low signal response. The engine control
unit detects that the water level is too high and V

sends the information to the dash panel insert.

The glow period warning lamp K29 will be
actuated in the dash panel insert and it will flash.
Flashing indicates a fault in the engine manage-
ment system. The engine should be checked in a
specialist workshop.

304_055

Wiring colour key

Positive Earth Input signal CAN drive train

databus

31
 Engine management

Actuators

Unit injector solenoid valves, cylinders 1 - 6

N240 … N244 and N245,
Unit injector solenoid valves, cylinders 7 - 10
N303 … 306

The unit injector solenoid valves are secured to

the unit injector bodies by union nuts.
The solenoid valves are actuated by the engine
control units.
These control start of delivery and the amount of
fuel injected.

As soon as a unit injector solenoid valve is

actuated by the engine control unit, the valve
needle is pushed onto its seat by the magnetic
ProCarManuals.com

coil and this closes the path of fuel to the

compression chamber of the unit injector.
Thereafter, injection will start.

The amount of fuel injected is determined by the

actuating period of the solenoid valve. As long
304_022
as the unit injector solenoid valve is closed, fuel
Unit injector solenoid valve
will be injected into the combustion chamber.

Effects of failure

If a unit injector solenoid valve should fail in its

function, the engine will not run smoothly and
performance will be impaired.

The unit injector solenoid valve has two safety

functions. If the valve stays open, pressure
cannot be built up in the unit injector. If the valve
stays closed, the compression chamber of the
unit injector can no longer be filled. In both
cases, no fuel can be injected into the cylinder. Unit injector solenoid valve

304_032

32
 Turbocharger positioning motors V280
and V281 (V10-TDI-engine)

The turbocharger positioning motors are bolted

to a bracket beneath the turbocharger. One con-
trol unit can be found in each positioning motor.

Task

The positioning motors are actuated by the

304_010
respective engine control unit via a CAN
databus. This improves regulation and fault Turbocharger 2
diagnosis. The improvement is thanks to positioning motor V281 Turbocharger 1
information about guide vane positioning and positioning motor V280
detected faults that the engine control units
ProCarManuals.com

receive. The turbocharger guide vanes are

actuated via a rod assembly.
The turbocharger positioning motor is
Effects of failure designed specifically for use with the
turbocharger. For this reason, both
If the positioning motors fail in their function, parts should be only be removed or
charge pressure control is no longer possible. The replaced together.
amount of fuel injected is limited according to the It is critical that reference be made to
engine speed and engine performance will be the workshop manual.
impaired.

Charge pressure limitation solenoid valve N75

(R5-TDI-engine)

The charge pressure limitation solenoid valve can

be found beneath the variable turbocharger. 304_078

Task Effects of failure

The charge pressure limitation solenoid valve is The vacuum unit is filled with atmospheric
actuated by the engine control unit. Vacuum is pressure. Charge pressure is lower as a result
built up in the vacuum unit for guide vane and engine performance is impaired.
adjustment depending on the duty cycle.

33
 Engine management

Exhaust gas Exhaust gas

Exhaust gas recirculation solenoid valves N18 recirculation valve 2 N213 recirculation valve N18
and N213

The solenoid valves for exhaust gas recirculation

can be found on the suspension strut domes on
each side. The valves are electro-pneumatic.

Task

The valves are actuated with a duty cycle by the

engine control unit depending on the map. In this
way, the control pressure for the recirculation valve
can be set. The cross section of the exhaust Exhaust gas
manifold is changed in the exhaust gas recirculation valve
recirculation valve depending on the control
ProCarManuals.com

pressure and the amount of recirculated exhaust

gas set.

Effects of failure

If the signal fails, exhaust gas recirculation may no

longer be possible.
304_012
Intake manifold
flap motor 2 V275 Intake manifold
Intake manifold flap motors V157 and V275 flap motor V157

The V10-TDI-engine has two electrically adjustable

intake manifold flaps and there is one electric
motor for each flap. These can be found directly in
front of the respective exhaust gas recirculation
valve.

Task

– With the electrically adjustable intake manifold

flaps, differences between air intake pressure
and exhaust gas pressure are generated in 304_011
certain operating conditions. Effective exhaust
gas recirculation is guaranteed thanks to the
differences in pressure.
– When the engine is switched off, the flap is Effects of failure
closed and the flow of air interrupted. In this
way, less air is drawn in and compressed which In case of failure, effective exhaust gas
helps smooth run-down of the engine. recirculation is no longer possible.

34
 Intake manifold flap changeover valve N239
(R5-TDI-engine)

The intake manifold flap changeover valve can

be found on the right-hand suspension strut
dome.
304_048

Task Effects of failure

When the engine is switched off, the intake If the changeover valve fails in its function, the
manifold flap changeover valve is actuated by intake manifold flap will stay in the open
ProCarManuals.com

the engine control unit. Following this, the intake position. If this happens, strong jolts will be
manifold flap is closed and the flow of air noticeable when the engine is switched off.
interrupted. In this way, less air is drawn in and
compressed and the engine will run down
smoothly as a result.

EGR cooler changeover valves N345 and N381

(Phaeton only)

The exhaust gas recirculation cooler changeover

valves can be found in the vicinity of the exhaust
gas recirculation cooler.
304_048

Task Effects of failure

The changeover valve is actuated by the engine If the changeover valve fails in its function, the
control unit depending on the temperature. It exhaust gas cooling flap will stay in the closed
clears the path from the vacuum pump to the position and the exhaust gas will no longer be
membrane valve, the exhaust gas cooling flap cooled. This can lead to an increase in nitrogen
is actuated and the path through the cooler is oxide emissions.
cleared.

35
 Engine management

Exhaust gas recirculation cooler

(Phaeton only)

The V10-TDI-engine in the Phaeton is equipped

with independent coolers for the exhaust gas
recirculation system.

The pneumatically controlled flaps for exhaust

gas cooling allow activation of the cooler from a
coolant temperature of 50 oC.

304_014
Cooler for exhaust gas recirculation
ProCarManuals.com

To valve
Cooler for exhaust gas recirculation for exhaust gas recirculation

From
exhaust manifold
From
exhaust manifold
304_031

Vacuum unit

Coolant connection
Coolant distribution to switch unit
with flap for exhaust gas cooling

36
 To valve
for exhaust gas recirculation
Without exhaust gas cooling
Cooler for exhaust gas recirculation

304_037
Coolant From
connection Flap for exhaust manifold
Coolant exhaust gas cooling
ProCarManuals.com

The engine and the catalyst are cold. The exhaust gas cooling flap is closed. The exhaust gases are
directed past the cooler and are therefore not cooled. In this way, the engine will reach its effective
operating temperature quickly.

With exhaust gas cooling To valve

for exhaust gas recirculation
From exhaust manifold
to cooler through flow

304_025

Flap for
Coolant exhaust gas cooling

The engine and the catalyst have reached effective operating temperature. The exhaust gas cooling flap is
open. The exhaust gas is directed through the cooler and is therefore cooled.
The combustion temperature is reduced due to the cooled exhaust gases and a greater amount of
exhaust gas can be recirculated. In this way, fewer nitrogen oxides are produced and carbon build-up is
avoided.

37
 Engine management

Fuel pumps G6 and G23

Both electrical fuel pumps are installed in the fuel tank.

– Fuel pump G23 with fuel gauge sender G – Fuel pump G6 with fuel gauge sender 3 G237
and a suction jet pump can be found in the and a suction jet pump can be found in the
main chamber of the fuel tank. secondary chamber of the fuel tank.

Actuation of both electrical fuel pumps is done in parallel sequence via the fuel pump relay J17.
ProCarManuals.com

Fuel pump G23

Fuel pump G6
(presupply pump)
Fuel gauge sender G

Fuel gauge sender 3 G237

Suction jet pump 2

Suction jet pump 1

304_049

Suction jet pump 1 draws fuel from the main chamber into the presupply reservoir of fuel pump G6 and
suction jet pump 2 pumps out the secondary chamber into the presupply reservoir of fuel pump G23.
Both suction jet pumps are driven by the electrical fuel pumps.

Effects of failure

If one pump fails, engine performance will be The maximum speed is unattainable and the
impaired due to a restriction in the amount of engine will not run smoothly at high revs.
fuel supplied.

38
 Thermostat for map-controlled
engine cooling F265

The thermostat for map-controlled engine

cooling can be found in the coolant distribution
housing. It has the task of switching between the
large and small coolant circuits. To do this, it is
actuated by the engine control unit according to
the engine operating conditions. Maps are
stored in the engine control unit which contain
temperature specifications depending on the
engine load.

Map-controlled engine cooling has the

advantage that the coolant temperature can be 304_016
ProCarManuals.com

adapted to the current operating conditions of

Coolant distribution housing
the engine. This helps to reduce fuel consumption
in the part-throttle range and also exhaust gas
emissions.

304_029

Coolant distribution housing

Spring

Resistance heater

A more detailed description of the

map-controlled engine cooling can Expanding material
be found in Self-Study Programme element
No. 222 "Electronically Controlled Plunger pin
Cooling System".

39
 Engine management

Additional coolant pump relay J496,

Continued coolant circulation pump V51 Continued coolant circulation pump V51

The continued coolant circulation pump can be

found on cylinder bank 1 on the vibration
damper side.
Due to the high working current, the pump is
actuated via a relay.
The additional coolant pump relay is installed in
the electronics box which can be found in the
plenum chamber.

Task
ProCarManuals.com

When the engine is switched off, the continued

coolant circulation pump will remain activate for
a maximum of 10 minutes. In this way, controlled 304_027
cooling of the engine is achieved. Vibration damper

Effects of failure

If the replay or the continued coolant circulation

pump fail, continued coolant circulation is no
longer possible. If the relay is defective, a fault
will be stored. A defective pump cannot be
detected.

Electrical actuation

The engine control unit actuates the continued

coolant circulation pump via the additional
coolant pump relay.
J496
V51
M

J623 Engine control unit 1

J496 Additional coolant pump relay J623
V51 Continued coolant circulation pump
304_067

40
 Fuel cooling pump relay J445 and fuel cooling
pump V166 (Touareg) Fuel cooling pump V166

The fuel cooling pump can be found on cylinder

bank 1 on the vibration damper side.
The pump is actuated via a relay due to the high
working current.
The relay for the fuel cooling pump is installed in
the electronics box which can be found in the
plenum chamber.

Task

The engine control unit actuates the fuel cooling

pump relay at and above a fuel temperature of
ProCarManuals.com

approximately 70 oC. The engine control unit

sends a working current to the fuel cooling pump
and the fuel cooler is then surrounded by 304_009
coolant. Fuel temperature will drop.
Vibration damper

Effects of failure

If the fuel cooling relay or fuel cooling pump fail,

fuel will no longer be cooled. The fuel tank and
the fuel gauge sender could become damaged.
A defective relay is stored as a fault. A defective
pump cannot be detected.

Electrical actuation

The fuel cooling pump is actuated via fuel

cooling pump relay J445 by engine control unit 1
J623.
J445
V166
M

J623 Engine control unit 1

J445 Fuel cooling pump relay J623
V166 Fuel cooling pump
304_068

41
 Engine management

Right solenoid valve for electro-hydraulic

engine mounting N145 (Phaeton)

The V10-TDI-engine in the Phaeton features

hydraulically dampening engine mountings.

These engine mountings reduce the transmission

of engine vibration to the body and in doing so
provide a high level of driving comfort.
ProCarManuals.com

304_041

Right solenoid valve for

electro-hydraulic engine
mounting N145

Right engine mounting

Left engine mounting

Left engine bracket

Right engine bracket

Engine carrier

304_040

42
 This is how it works:

The hydraulically dampening engine mountings The road speed and engine speed are used as
are actuated pneumatically via solenoid valve input signals.
N145. The engine mountings reduce vibrations
that are transmitted to the body by the engine
across the entire throttle range.

Engine control unit 1 J623

Control unit for ABS
with ESP J104
ProCarManuals.com

(road speed)

Engine speed
sender G28

Right solenoid valve for

From vacuum electro-hydraulic engine
pump mounting N145

Engine Engine
mounting, right mounting, left

304_042

More detailed information about the function of the engine mountings can be found in
Self-Study Programme No. 249 "Management of the W8 Engine in the Passat".

43
 Engine management

Functional diagram for V10-TDI-engine Key

F Brake light switch Q10 Glow plugs

30 30 F8 Kick-down switch ... Q19
15 15 F47 Brake pedal switch
F60 Idle switch V51 Continued coolant circulation pump
F265 Thermostat for map-controlled engine V157 Intake manifold flap motor
cooling V166 Fuel cooling pump
V275 Intake manifold flap motor 2
G6 Fuel pump (presupply pump) V280 Turbocharger 1 positioning motor
G23 Fuel pump V281 Turbocharger 2 positioning motor
G
G28 Engine speed sender
J317 G31 Charge pressure sender Z19 Lambda probe heating
G39 Lambda probe Z28 Lambda probe heating 2
J689
G40 Hall sender
A A G42 Intake air temperature sender
G62 Coolant temperature sender
G70 Air mass meter
ProCarManuals.com

G79 Accelerator pedal position sender

G81 Fuel temperature sender Additional signal
G83 Coolant temperature sender
B B
radiator outlet 1 CAN drive train databus (high)
C C C
D D G108 Lambda probe 2 2 CAN drive train databus (low)
G133 Fuel composition sender 3 Radiator fan output stage 1
V157 V280 V281 F265 F47 F J17 G108 Z28 V275 G246
G246 Air mass meter 2 4 Radiator fan output stage 2
J496 J445 J52 N145 H J495
G248 Fuel temperature sender 2 5 Coms lead (diagnosis connection)
M M M V51 V166 λ M N213 N381
G299 Intake air temperature sender 2 6 Cruise control system switch
M M M M
G447 Charge pressure sender 2 (ON/OFF)
G23 G6
N18 N345 7 Road speed signal
J17 Fuel pump relay
Q10...Q14 Q15...Q19 8 Alternator terminal DFM
J52 Glow plug relay
1 9 Starter relay J...
J317 Voltage supply relay - term. 30
J445 Fuel cooling pump relay
2
J495 Glow plug relay 2
J496 Additional coolant pump relay
J623 Engine control unit 1
J623 J624 J624 Engine control unit 2
J689 Voltage supply relay 2 term. 30 A
B
N18 Exhaust gas recirculation valve C
E G D
N145 Electro-hydraulic engine mounting Connections within functional diagram
F E F solenoid valve E
N213 Exhaust gas recirculation valve 2 F
+ N240 Unit injector solenoid valves G
H
λ ... N245
N303
3 4 5 6 7 8 9 1 2 5
... N306
N240 N241 N242 N243 N244 G81 G62 G83 G133 G31 G42 G40 G28 F60/F8 G79 G70 G39 Z19 N245 N303 N304 N305 N306 G248 G447 G299
N345 EGR cooler changeover valve
N381 EGR cooler changeover valve 2
H 304_001

44 45
 Engine management

Functional diagram for V10-TDI-engine Key

F Brake light switch Q10 Glow plugs

30 30 F8 Kick-down switch ... Q19
15 15 F47 Brake pedal switch
F60 Idle switch V51 Continued coolant circulation pump
F265 Thermostat for map-controlled engine V157 Intake manifold flap motor
cooling V166 Fuel cooling pump
V275 Intake manifold flap motor 2
G6 Fuel pump (presupply pump) V280 Turbocharger 1 positioning motor
G23 Fuel pump V281 Turbocharger 2 positioning motor
G
G28 Engine speed sender
J317 G31 Charge pressure sender Z19 Lambda probe heating
G39 Lambda probe Z28 Lambda probe heating 2
J689
G40 Hall sender
A A G42 Intake air temperature sender
G62 Coolant temperature sender
G70 Air mass meter

ProCarManuals.com
G79 Accelerator pedal position sender
G81 Fuel temperature sender Additional signal
G83 Coolant temperature sender
B B
radiator outlet 1 CAN drive train databus (high)
C C C
D D G108 Lambda probe 2 2 CAN drive train databus (low)
G133 Fuel composition sender 3 Radiator fan output stage 1
V157 V280 V281 F265 F47 F J17 G108 Z28 V275 G246
G246 Air mass meter 2 4 Radiator fan output stage 2
J496 J445 J52 N145 H J495
G248 Fuel temperature sender 2 5 Coms lead (diagnosis connection)
M M M V51 V166 λ M N213 N381
G299 Intake air temperature sender 2 6 Cruise control system switch
M M M M
G447 Charge pressure sender 2 (ON/OFF)
G23 G6
N18 N345 7 Road speed signal
J17 Fuel pump relay
Q10...Q14 Q15...Q19 8 Alternator terminal DFM
J52 Glow plug relay
1 9 Starter relay J...
J317 Voltage supply relay - term. 30
J445 Fuel cooling pump relay
2
J495 Glow plug relay 2
J496 Additional coolant pump relay
J623 Engine control unit 1
J623 J624 J624 Engine control unit 2
J689 Voltage supply relay 2 term. 30 A
B
N18 Exhaust gas recirculation valve C
E G D
N145 Electro-hydraulic engine mounting Connections within functional diagram
F E F solenoid valve E
N213 Exhaust gas recirculation valve 2 F
+ N240 Unit injector solenoid valves G
H
λ ... N245
N303
3 4 5 6 7 8 9 1 2 5
... N306
N240 N241 N242 N243 N244 G81 G62 G83 G133 G31 G42 G40 G28 F60/F8 G79 G70 G39 Z19 N245 N303 N304 N305 N306 G248 G447 G299
N345 EGR cooler changeover valve
N381 EGR cooler changeover valve 2
H 304_001

44 45
 Service

Self-diagnosis

Diagnosis

On vehicle diagnosis, testing and information

systems VAS 5051 and VAS 5052:

– Guided fault finding* and

– Vehicle self-diagnosis

can be selected.

Operating mode "Guided fault finding"

checks all vehicle-specific control units for stored

ProCarManuals.com

faults and automatically compiles an individual

testing plan based on the results.
This plan is carried out in conjunction with ELSA
information, such as current flow diagrams or
workshop manuals, selected to aid fault finding.
304_051

In addition to this, you can also compile your

own testing plan. The tests you choose from the
selection of functions and components will be
added to the testing plan and can be carried out
as a diagnostic sequence in any order.

Operating mode "Vehicle Self-Diagnosis"

can be used in the same way as normal but no

additional information is available from ELSA.

304_052

More detailed information about

guided fault finding can be found in
chapter 7 of the VAS 5051 operating
handbook.
* Not with vehicle diagnosis and
service information system VAS 5052

46
 Workshop Equipment

Designation Tool

Test box
V.A.G 1598/42
ProCarManuals.com

304_083

Adapter lead
V.A.G 1598/39-1

304_084

Adapter lead
V.A.G 1598/39-2

304_085

47
 Test your knowledge

Which answers are correct?

One or more answers could be correct.

1. Which special features does Bosch EDC 16 have?

a) It is designed for both single control unit and double control unit concepts.

b) It was designed exclusively for the V10-TDI-engine.

c) It has torque-orientated engine management.

2. Which statements about the V10-TDI-engine are correct?

ProCarManuals.com

a) The basic functions for cylinder bank 1 are carried out by engine control unit 1
and the basic functions for cylinder bank 2 by engine control unit 2.

b) Information that is received by engine control unit 1 is sent to engine control unit 2
via an internal CAN databus.

c) Engine control unit 1 is responsible for injection and exhaust gas recirculation and
engine control unit 2 is responsible for the remaining functions.

3. On the V10-TDI-engine, how are the engine control units allocated to the cylinder banks?

a) The engine control units have different part numbers.

b) The engine control units are coded using VAS 5051.

c) In the connector for engine control unit 2 J624 there is an additional coding link
which facilitates allocation.

48
 4. On the V10-TDI-engine, Lambda probes calculate the remaining oxygen content in the
exhaust gas. In this way, ...

a) the amount of fuel injected is adapted.

b) the amount of nitrogen oxide in the exhaust gas is calculated.

c) the amount of recirculated exhaust gas is corrected.

ProCarManuals.com

5. Why is an independent cooler for exhaust gas recirculation used on the V10-TDI-engine in the
Phaeton?

a) To prevent excessive warm-up periods of the engine caused by cooled exhaust gases.

b) So that the coolant does not get too hot.

c) To prevent increased carbon dioxide and carbon monoxide emissions during warm-up.

6. What are the advantages of turbocharger positioning motor actuation via the CAN drive
train databus?

a) More precise regulation is made possible as the position of the guide vanes is detected.

b) More precise fault diagnosis is made possible as detected faults are sent to the engine
control units.

c) It is cheaper.

49
 Test your knowledge

7. Which statements about the fuel cooling pump are correct?

a) The fuel cooling pump operates continually while the engine is running.

b) The fuel cooling pump can be found in the Touareg on the V10-TDI-and R5-TDI-engines.

c) The fuel cooling pump is actuated when the fuel temperature is approximately 70 °C.

8. The engine speed sender G28 on the V10-TDI-engine ...

ProCarManuals.com

a) sends its signals directly to both engine control units.

b) sends its signals to engine control unit 1 J623 and these are then passed on
to engine control unit 2 J624 via an internal CAN databus.

c) sends its signals to engine control unit 1 J623 and these are then passed on
to engine control unit 2 J624 via a separate cable.

1. a, c; 2. a, b; 3. c; 4. c; 5. a, c; 6. a, b; 7. b, c; 8. c

Answers

50
 ProCarManuals.com

Notes

51
 Service. 304
ProCarManuals.com

For internal use only. © VOLKSWAGEN AG, Wolfsburg

All rights reserved. Technical specifications subject to change without notice.
000.2811.24.20 Technical status: 11/02

❀ This paper is produced from

non-chlorine-bleached pulp.