MP 255000-01-AFL

CARGO COMPARTMENT NETS

visual inspection of the cargo compartment
door nets and divider nets.

MJC 25-50-00-01-AFL
 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

DATE A/C TYPE A/C REGISTRATION PAGE

22.07.2008 A319/A320/ A321 1 of 10

TITLE

Visual inspection of FWD and AFT Cargo Compartment Door Nets and Divider Nets.

REFERENCE MEN MAN-HOURS DOWN TIME

EO A20-25-0007 rev 00 1 1.5 1.5

MP Task 255000-01-AFL DEP/TEL NAME

ED/45-50 Vorushkin
ITEM TASK/JOB DESCRIPTION MECH INSP

1. Get access

(1) Open the applicable cargo compartment door and install the actuator safety locks
(Ref. AMM TASK 52-30-00-860-001).
(2) Put the access platform in position at the opening of the FWD and/or AFT cargo compartment
door.
(3) Put a WARNING NOTICE on the control panel of applicable CLS to tell persons not to use it.

2. Door Nets and Divider Nets inspection

NOTE: For net parts definition refer to figures 10 and 11.

(1) Make sure all the nets are present in cargo compartment. Refer to applicable figures 1 to 9.

NOTE: Refer to Table 1 for damage allowances.

(2) Examine the webbing of the door nets and the divider nets for:
- cuts, twists, wear, damaged stitches and any other damage
(3) Examine the fittings and the metal parts of the nets for:
- missing, corroded and damaged fittings.
- correct operation.
(4) Examine the stanchions of the nets (if installed) for:
- dents and damage to the tube
- corrosion of the metal parts
- loose, missing and damaged metal loops and connectors
- correct operation of the telescopic section and the end fittings.
(5) Examine the identification labels of the nets:
- look for loose, missing and damaged identification labels
- make sure that you can read the data on the identification labels.
(6) Examine the rubber coated fabric of the nets:
- look for cuts, missing areas and other damage
- make sure that the screen is correctly attached to the webbing.

3. Net Attachment Points inspection

NOTE: Refer to Table 1 for damage allowances.

(1) Examine all the net attachment points and the adjacent areas for cracks, corrosion and other
damage.
(2) Make sure that the net attachment points are correctly attached.

Revision 0 From 2.13.7/1

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

2 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

4. Close-up

(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the warning notices.
(3) Remove the actuator safety locks, remove the access platform(s) and close the FWD or AFT
cargo-compartment door (Ref. TASK 52-30-00-860-002).

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

3 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Table 1. Damage allowances.

Component Damage Action Required

Webbing - Dirt and contamination that you can remove. Allowable

- Small areas where the web fibers are damaged from Allowable
wear or chafing.
- Damaged stitches or stitch patterns at the web Replace part at the
intersections. Not more than two damaged flag stitch next convinient
patterns at the intersections are permitted. opportunity
- Damaged stitches at the flag stitch patterns that attach Part is
the fittings. uncerviceable

- All cuts Part is

unserviceable
Net fittings - Dirt and corrosion that you can remove, and does not Allowable
and metal have an effect on the function of the component.
parts - Damage to the adjusters that stops you to correct Replace at the
adjustment of the net. next convinient
opportunity
- Missing or damaged fittings that stop the connection of Fittings is
the net to the aircraft or to another net. unserviceable
Stanchions - Small areas of corrosion on the tube that you can Allowable
remove.
- One metal loop or connector missing. Allowable
- More than one metal loop or connector missing. Replace part at the
next convinient
opportunity
- Dents in the tube less than 2.0mm (0.08 in.) deep. Allowable
- Dents in the tube more than 2.0mm (0.08 in.) deep. Replace part at the
next convinient
opportunity
Identification - Damaged material, but you can read the data. Allowable
labels - Label missing, or you cannot read the data. Part is
unserviceable
Rubber - Small areas of chafing or cuts in the fabric, less than Allowable
coated fabric 250.0mm (10.0 in.) long.
(if installed) - Cuts in the fabric more than 250.0mm (10.0 in.). Replace at the
next convinient
opportunity

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

4 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 1. A319 FWD Cargo Compartment Nets (ref. to Figure 7 for detail)

Figure 2. A319 AFT Cargo Compartment Nets (ref. to Figure 7 for detail)

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

5 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 3. A320 FWD Cargo Compartment Nets (ref. to Figure 7 for detail)

Figure 4. A320 AFT Cargo Compartment Nets (ref. to Figure 7 for detail)

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

6 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 5. A321 FWD Cargo Compartment Nets (ref. to Figure 7 for detail)

Figure 6. A321 AFT Cargo Compartment Nets (ref. to Figure 7 for detail)

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

7 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 7. Details A, B, C, D for Fig. 1 to 6

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

8 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 8. A319 Bulk Cargo Compartment Nets location

Figure 9. A320/A321 Bulk Cargo Door and Compartment Nets location

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

9 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 10. Net Parts Definition

Revision 0 From 2.13.7/2

 MAINTENANCE JOB CARD WORK No: 25-50-00-01-AFL

A/C REGISTRATION PAGE

10 of 10
ITEM TASK/JOB DESCRIPTION MECH INSP

Figure 11. Net Parts Definition

Revision 0 From 2.13.7/2

 A20-33-0127
NAVIGATION LIGHTS
operational test of the navigation lights

AMM Task 33-41-00-710-001

 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.
** ON A/C FSN ALL
TASK 33-41-00-710-001-A
Operational Test of the Navigation Lights
FIN: 10LA
** ON A/C FSN 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-300
15LA
** ON A/C FSN 001-050, 301-350, 401-450, 551-650
16LA
** ON A/C FSN ALL
9LA

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE
YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR
CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE
LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING
GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE
AIRCRAFT AND/OR EQUIPMENT.

WARNING: DO NOT LOOK DIRECTLY AT THE LIGHT FLASH DURING THE TEST.
SUPPLY A COVER, OR SHIELD, TO GIVE PROTECTION FROM THE LIGHT FLASH TO
PERSONS IN THE TEST AREA.

1. Reason for the Job

Self explanatory

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

Q
REFERENCE DESIGNATION
TY
No specific A SAFETY BARRIER(S)
R

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

Q
REFERENCE DESIGNATION
TY
No specific A WARNING NOTICE(S)
R

B. Referenced Information

REFERENCE DESIGNATION
Ref. 24-41-00-861-002-A Energize the Aircraft Electrical Circuits from the External
Power
Ref. 24-41-00-861-002-A01 Energize the Aircraft Electrical Circuits from the APU
Ref. 24-41-00-861-002-A02 Energize the Aircraft Electrical Circuits from Engine 1(2)
Ref. 24-41-00-862-002-A De-energize the Aircraft Electrical Circuits Supplied from
the External Power
Ref. 24-41-00-862-002-A01 De-energize the Aircraft Electrical Circuits Supplied from
the APU
Ref. 24-41-00-862-002-A02 De-energize the Aircraft Electrical Circuits Supplied from
the Engine 1(2)
** ON A/C FSN 551-650
Ref. 44-33-00-040-804-A Deactivation of Broadband System for Maintenance
Ref. 44-33-00-440-804-A Reactivation of Broadband System after Maintenance
** ON A/C FSN 116-117, 122-125, 128-143, 211-212, 215-215, 222-300
Ref. Fig. Navigation Lights - Component Location
** ON A/C FSN 144-150, 152-200
Ref. Fig. Navigation Lights - Component Location
** ON A/C FSN 001-050, 301-350, 401-450, 551-650
Ref. Fig. Navigation Lights - Component Location

** ON A/C FSN ALL

3. Job Set-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350,
401-450

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

SUBTASK 33-41-00-941-056-A
A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's
instructions and your local regulations.
(2) Put a WARNING NOTICE(S) on the panel 25VU to tell persons not to operate the
navigation lights or the strobe lights.
** ON A/C FSN 551-650
SUBTASK 33-41-00-941-056-B
A. Safety Precautions

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A RADIUS OF 29

METERS (96 FEET) AROUND AND ABOVE THE BROADBAND
ANTENNA, MAKE SURE THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS AND CAN
CAUSE INJURY TO PERSONS.
(1) Deactivate the broadband antenna Ref. AMM TASK 44-33-00-040-804.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's
instructions and your local regulations.
(3) Put a WARNING NOTICE(S) on the panel 25VU to tell persons not to operate the
navigation lights or the strobe lights.
** ON A/C FSN ALL
SUBTASK 33-41-00-861-050-A
B. Energize the Electrical Circuits
(1) Energize the aircraft electrical circuits Ref. AMM TASK 24-41-00-861-002.

4. Procedure
** ON A/C FSN 116-117, 122-125, 128-143, 211-212, 215-215, 222-300
Ref. Fig. Navigation Lights - Component Location
** ON A/C FSN 144-150, 152-200

EMB SB 57-1186 for A/C 144-150, 152-153

Ref. Fig. Navigation Lights - Component Location
** ON A/C FSN 001-050, 301-350, 401-450, 551-650
Ref. Fig. Navigation Lights - Component Location
** ON A/C FSN 116-117, 122-125, 128-143, 211-212, 215-215, 222-300

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

SUBTASK 33-41-00-710-050-D
A. Operational Test
(1) Operational Test of the Navigation Lights

ACTION RESULT
1. On the EXT LT control panel 25VU: - the NAV 1 lamps of the navigation
- put the toggle switch NAV & lights (9LA and 10LA) come on
LOGO (3LA) to the 1 position - the NAV 1 lamp of the navigation
light (15LA) comes on
- put the toggle switch NAV & - the NAV 2 lamps of the navigation
LOGO (3LA) to the 2 position lights (9LA and 10LA) come on
and the NAV 1 lamps go off
- the NAV 2 lamp of the navigation
light (15LA) comes on and the
NAV 1 lamp goes off
- put the toggle switch NAV & - the navigation lights (9LA, 10LA
LOGO (3LA) to the OFF position. and 15LA) go off.

** ON A/C FSN 144-150, 152-200

EMB SB 57-1186 for A/C 144-150, 152-153

SUBTASK 33-41-00-710-050-G
A. Operational Test
(1) Operational Test of the Navigation Lights

ACTION RESULT
1. On the section EXT LT of the - The NAV 1 LEDs of the navigation
overhead control and indicating panel light of the left wing tip (9LA) come
25VU: on.
- Put the toggle switch NAV & - The NAV 1 LEDs of the navigation
LOGO (3LA) to the 1 position. light of the right wing tip (10LA)
come on.
- The NAV 1 lamp of the rear
navigation light (15LA) comes on.
2. On the section EXT LT of the - The NAV 1 LEDs of the navigation
overhead control and indicating panel light of the left wing tip (9LA) go
25VU: off.

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

ACTION RESULT
- Put the toggle switch NAV & - The NAV 2 LEDs of the navigation
LOGO (3LA) to the 2 position. light of the left wing tip (9LA) come
on.
- The NAV 1 LEDs of the navigation
light of the right wing tip (10LA) go
off.
- The NAV 2 LEDs of the navigation
light of the right wing tip (10LA)
come on.
- The NAV 1 lamp of the rear
navigation light (15LA) goes off.
- The NAV 2 lamp of the rear
navigation light (15LA) comes on.
3. On the section EXT LT of the - The NAV 2 LEDs of the navigation
overhead control and indicating panel light of the left wing tip (9LA) go
25VU: off.
- Put the toggle switch NAV & - The NAV 2 LEDs of the navigation
LOGO (3LA) to the OFF position. light of the right wing tip (10LA) go
off.
- The NAV 2 lamp of the rear
navigation light (15LA) goes off.

** ON A/C FSN 001-050, 301-350, 401-450, 551-650

SUBTASK 33-41-00-710-050-H
A. Operational Test
(1) Operational Test of the Navigation Lights

ACTION RESULT
1. On the section EXT LT of the - The NAV 1 LEDs of the left light
overhead control and indicating panel navigation-assembly (9LA) come
25VU: on.
- Put the toggle switch NAV & - The NAV 1 LEDs of the right light
LOGO (3LA) to the 1 position. navigation-assembly (10LA) come
on.
- The NAV 1 LEDs of the navigation
and strobe rear light-assembly
(16LA) come on.

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

ACTION RESULT
2. On the section EXT LT of the - The NAV 1 LEDs of the left light
overhead control and indicating panel navigation-assembly (9LA) go off.
25VU: - The NAV 2 LEDs of the left light
- Put the toggle switch NAV & navigation-assembly (9LA) come
LOGO (3LA) to the 2 position. on.
- The NAV 1 LEDs of the right light
navigation-assembly (10LA) go off.
- The NAV 2 LEDs of the right light
navigation-assembly (10LA) come
on.
- The NAV 1 LEDs of the navigation
and strobe rear light-assembly
(16LA) go off.
- The NAV 2 LEDs of the navigation
and strobe rear light-assembly
(16LA) come on.
3. On the section EXT LT of the - The NAV 2 LEDs of the left light
overhead control and indicating panel navigation-assembly (9LA) go off.
25VU: - The NAV 2 LEDs of the right light
- Put the toggle switch NAV & navigation-assembly (10LA) go off.
LOGO (3LA) to the OFF position. - The NAV 2 LEDs of the navigation
and strobe rear light-assembly
(16LA) go off.

** ON A/C FSN ALL

5. Close-up
SUBTASK 33-41-00-862-050-A
A. De-energize the Electrical Circuits
(1) De-energize the aircraft electrical circuits Ref. AMM TASK 24-41-00-862-002.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350,
401-450
SUBTASK 33-41-00-942-054-A
B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 6 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

(3) Remove the WARNING NOTICE(S).

(4) Remove the ground support and maintenance equipment, the special and standard
tools and all other items.
** ON A/C FSN 551-650
SUBTASK 33-41-00-942-054-B
B. Removal of Equipment
(1) Reactivate the broadband antenna Ref. AMM TASK 44-33-00-440-804.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Remove the safety barriers.
(4) Remove the WARNING NOTICE(S).
(5) Remove the ground support and maintenance equipment, the special and standard
tools and all other items.

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 7 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

L R

Figure 33-41-00-991-00100-00-D (SHEET 1) - Navigation Lights - Component Location

** ON A/C FSN 116-117, 122-125, 128-143, 211-212, 215-215, 222-300

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 8 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

B D
C

A A

B C

Figure 33-41-00-991-00100-00-J (SHEET 1) - Navigation Lights - Component Location

** ON A/C FSN 144-150, 152-200
EMB SB 57-1186 for A/C 144-150, 152-153

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 9 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-41-00-710-001-A
Tail Number - MSN - TITLE: 33-41-00-05 CONF 00
FSN: 33-41-00-710-001-A - Operational Test of the Navigation
ALL Lights

MECH. INSP.

B D
C

A A

B C

Figure 33-41-00-991-00100-00-K (SHEET 1) - Navigation Lights - Component Location

** ON A/C FSN 001-050, 301-350, 401-450, 551-650
© *** END OF CARD ***

JCP Title: A20-33-0127 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 10 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 MP 521000-01-1
PASSENGER/CREW DOOR
check emergency cylinder/accumulator pressure

AMM Task 52-10-00-210-004

 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
52-10-00-210-004-A
Tail Number - MSN - TITLE: 52-10-00-06 CONF 00
FSN: 52-10-00-210-004-A - Check Pressure of Emergency Cylinder/
ALL Accumulator of the Passenger/Crew Doors

MECH. INSP.
** ON A/C FSN ALL
TASK 52-10-00-210-004-A
Check Pressure of Emergency Cylinder/Accumulator of the Passenger/Crew Doors
1. Reason for the Job
Refer to the MPD TASK: 521000-01
CHECK EMERGENCY CYLINDER/ACCUMULATOR PRESSURE

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer
to the MPD task applicability.
NOTE: This task is only applicable to aircraft with the door damper and emergency operation
cylinder not connected to the CIDS.

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

Q
REFERENCE DESIGNATION
TY
No specific 1 ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE

B. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

831 FORWARD PASSENGER/CREW DOOR
832 AFT PASSENGER/CREW DOOR
841 FORWARD PASSENGER/CREW DOOR
842 AFT PASSENGER/CREW DOOR
831, 832, 841, 842

C. Referenced Information

REFERENCE DESIGNATION
Ref. 52-10-00-010-001-A Opening of the Passenger/Crew Door
Ref. 52-10-00-410-001-A Closing of the Passenger/Crew Door
Ref. 52-10-00-614-001-A Discharging/Charging of the Door Damper and Emergency
Operation Cylinder of the Passenger/Crew Doors

JCP Title: 521000-01-1 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
52-10-00-210-004-A
Tail Number - MSN - TITLE: 52-10-00-06 CONF 00
FSN: 52-10-00-210-004-A - Check Pressure of Emergency Cylinder/
ALL Accumulator of the Passenger/Crew Doors

MECH. INSP.

REFERENCE DESIGNATION
** ON A/C FSN 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450,
551-650
Ref. Fig. Door-Damper and Emergency-Operation Cylinder

** ON A/C FSN ALL

3. Job Set-up
SUBTASK 52-10-00-010-079-A
A. Get Access

WARNING: DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS

MORE THAN 65 KNOTS.

WARNING: STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT

FLASHES. IF THE RED WARNING LIGHT FLASHES, REMAINING
PRESSURE CAN CAUSE THE DOOR TO OPEN SUDDENLY AND CAN:
- KILL OR CAUSE SERIOUS INJURY TO PERSONS
- CAUSE DAMAGE TO THE AIRCRAFT.
(1) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in front of the
passenger/crew door 831 or 841 or 832 or 842.
(2) Open the passenger/crew door Ref. AMM TASK 52-10-00-010-001.

4. Procedure
SUBTASK 52-10-00-210-080-A
A. Check of the Pressure.
** ON A/C FSN 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450,
551-650
Ref. Fig. Door-Damper and Emergency-Operation Cylinder
** ON A/C FSN ALL

CAUTION: THE PRESSURE ON THE PRESSURE INDICATOR OF THE BOTTLE

MUST BE RELATED TO THE PRESSURE CORRECTED FOR
TEMPERATURE.
(1) Make sure that the door is open.
(2) Do a check of the pressure:

JCP Title: 521000-01-1 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
52-10-00-210-004-A
Tail Number - MSN - TITLE: 52-10-00-06 CONF 00
FSN: 52-10-00-210-004-A - Check Pressure of Emergency Cylinder/
ALL Accumulator of the Passenger/Crew Doors

MECH. INSP.

(a) Write the pressure value shown on the pressure gauge (1).
(b) Compare this value with the value on the placard (2) for the ambient
temperature.

NOTE: The minimum operating pressure value for the door to be

serviceable is 1305 PSI at 20°C only for maintenance operation.
NOTE: To get a correct pressure, the air bottle must be stable at ambient
temperature before you do the inspection.
NOTE: Bubbles in the pressure gauge with a maximum diameter equal to
the dial are permitted.
(3) If the oil level, in the pressure gauge, is not sufficient to have the pointer in the liquid
(with the dial horizontal), you must discard the pressure gauge.
(4) If the pressure is not correct, charge the cylinder bottle. Ref. AMM TASK
52-10-00-614-001

5. Close-up
SUBTASK 52-10-00-410-088-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the applicable passenger/crew door 831 or 841 or 832 or 842 Ref. AMM TASK
52-10-00-410-001:
(3) Remove the access platform(s).

JCP Title: 521000-01-1 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
52-10-00-210-004-A
Tail Number - MSN - TITLE: 52-10-00-06 CONF 00
FSN: 52-10-00-210-004-A - Check Pressure of Emergency Cylinder/
ALL Accumulator of the Passenger/Crew Doors

MECH. INSP.

B A

D 2

D C

C C

Figure 52-10-00-991-04400-00-C (SHEET 1) - Door-Damper and Emergency-Operation Cylinder

** ON A/C FSN 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450, 551-650
© *** END OF CARD ***

JCP Title: 521000-01-1 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 MP 791000-02-AFL
OIL STORAGE
check pop out indicator of EMCD

AMM Task 12-13-79-610-002

 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350,
401-450
TASK 12-13-79-610-002-A
Check oil level and replenish Check Pop Out Indicator of EMCD (Electrical Master Chip Detector)

WARNING: DO NOT REMOVE THE FILLER CAP OF THE OIL TANK IMMEDIATELY AFTER
ENGINE OPERATION. LET THE OIL PRESSURE DECREASE FOR A MINIMUM OF 5
MINUTES AFTER THE ENGINE SHUTDOWN. IF YOU OPEN THE FILLER CAP WHEN
THERE IS PRESSURE IN THE TANK, THE OIL CAN BURN YOU DANGEROUSLY.

1. Reason for the Job

Self explanatory

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

Q
REFERENCE DESIGNATION
TY
No specific 1 DETECTOR-COMBUSTIBLE GAS
No specific 1 VISCOMETER

B. Consumable Materials

REFERENCE DESIGNATION
CP2442 engine oil
14SBA1 Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS ZONE DESCRIPTION

FOR 1000EM1(ENGINE-1)
437BL
FOR 1000EM2(ENGINE-2)
447BL

D. Referenced Information

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

REFERENCE DESIGNATION
Ref. 73-11-20-000-002-A Removal of the Servo Fuel Heater
Ref. 73-11-20-400-002-A Installation of the Servo Fuel Heater
Ref. 79-11-10-300-003-A Replacement of the O-ring of the Oil Tank Filler Cap
Ref. 79-21-20-000-002-A Removal of the Main Oil/Fuel Heat Exchanger
Ref. 79-21-20-400-002-A Installation of the Main Oil/Fuel Heat Exchanger
Ref. TSM 79-00-00-810-833 The Electrical Master Chip Detector indication is popped
out - Engine 1
Ref. TSM 79-00-00-810-834 The Electrical Master Chip Detector indication is popped
out - Engine 2
Ref. Fig. Oil Tank Sight Gage
Ref. Fig. Measuring the Viscosity of the Oil
Ref. Fig. Removal of the Oil Tank Filler Cap

3. Job Set-up
SUBTASK 12-13-79-941-068-A
A. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before
you do this procedure.
SUBTASK 12-13-79-010-065-A
B. Open the oil tank servicing access door :
(1) FOR 1000EM1 (ENGINE-1)
437BL
(2) FOR 1000EM2 (ENGINE-2)
447BL

4. Procedure
Ref. Fig. Oil Tank Sight Gage
Ref. Fig. Measuring the Viscosity of the Oil
SUBTASK 12-13-79-210-065-A
A. Check oil level and master Magnetic Chip Detector (MCD) visual indicator.

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

NOTE: In order to reduce burden for nuisance EMCD pop out indication, the inspection
of the Electrical Master Chip Detector can be deferred to the next convenient
maintenance opportunity where trained personnel can perform the inspection
without interfering with revenue service operation.
(1) Check the Electrical Master Chip Detector visual indication after the next flight. If the
pop-out is extended Ref. TSM 79-00-00-810-833 or Ref. TSM 79-00-00-810-834.
(2) Check oil level on the sight gage.

NOTE: This task is the procedure to replenish the engine oil.

- Oil should be added not less than 5 minutes and not more than 60
minutes after engine shutdown while the oil in the tank is still
warm. This will prevent the over-servicing of the engine.
- If the oil in the tank is cool or cold, the oil density will increase
(volume decreases) and the oil tank can be over-serviced.
- If the oil tank is over-serviced, this will not damage the engine.
The extra oil will be blown overboard through the engine vent
system.
- The quantity of oil can cause incorrect calculations for the
consumption rate.
(a) If oil level is below full mark, add oil as follows.
SUBTASK 12-13-79-100-051-A
B. Clean the oil tank scupper:

CAUTION: MAKE SURE THAT THE OIL TANK SCUPPER IS CLEAN TO PREVENT
CONTAMINATION OF THE TANK DURING THE SERVICING
OPERATIONS.
(1) Clean the oil tank scupper with a Textile-Lint free Cotton - (Material Ref. 14SBA1)
before you remove the oil tank filler cap.
SUBTASK 12-13-79-010-066-B
C. Open the Oil Tank.
Ref. Fig. Removal of the Oil Tank Filler Cap

WARNING: DO NOT REMOVE THE FILLER CAP OF THE OIL TANK IMMEDIATELY
AFTER ENGINE OPERATION. LET THE OIL PRESSURE DECREASE
FOR A MINIMUM OF 5 MINUTES AFTER THE ENGINE SHUTDOWN. IF
YOU OPEN THE FILLER CAP WHEN THERE IS PRESSURE IN THE
TANK, THE OIL CAN BURN YOU DANGEROUSLY.

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

CAUTION: BE CAREFUL TO REMOVE THE OIL TANK FILLER-CAP, DO NOT

APPLY MORE FORCE THAN IS NECESSARY TO ITS HANDLE. TOO
MUCH FORCE CAN CAUSE DAMAGE TO OCCUR TO ITS LOCKING
DEVICE.

CAUTION: DO NOT TRY TO PULL THE HANDLE OF THE OIL-TANK FILLER-CAP

OUT OF ITS STOP LIMITS.
(1) Raise oil tank filler cap handle to vertical (unlocked) position.
(2) Turn the handle of the filler cap counterclockwise 45° against its stop to disengage
the locking device and remove the cap.

NOTE: If it is difficult to open the filler cap, you must stay for 5 more minutes at
least to do step (2) again.
(3) Do a check for fuel in the oil.

CAUTION: BEFORE YOU ADD OIL IN THE OIL TANK DURING ITS
SERVICING, MAKE SURE THE OIL IN TANK DOES NOT
CONTAIN FUEL. IF IT SMELLS OF FUEL, REPLACE THE MAIN
OIL/FUEL HEAT EXCHANGER AND SERVO FUEL HEATER
THEN FLUSH THE ENGINE OIL SYSTEM.

CAUTION: IF YOU THINK THERE ARE FUEL FUMES WHEN YOU REMOVE
THE OIL FILLER CAP, DO A CHECK FOR FUEL IN THE OIL. IF
THERE IS FUEL IN THE OIL TANK, REPLACE THE MAIN OIL/
FUEL HEAT EXCHANGER AND THE SERVO FUEL HEATER
THEN FLUSH THE ENGINE OIL SYSTEM.
(a) If you think there is fuel in the oil, use one of the following available on-site
test kits to examine the oil:
- VISCOMETER (measuring the viscosity of the oil),
- DETECTOR-COMBUSTIBLE GAS (checking for presence of a combustible
vapor).
1 If the test fails then fuel is found, do these steps:

a Replace the Main Oil/Fuel Heat Exchanger Ref. AMM TASK

79-21-20-000-002 Ref. AMM TASK 79-21-20-400-002.

b Replace the servo fuel heater Ref. AMM TASK

73-11-20-000-002 Ref. AMM TASK 73-11-20-400-002.

2 If the test passes, no fuel is found.

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.
SUBTASK 12-13-79-612-070-A
D. Added oil in the oil tank:
Ref. Fig. Oil Tank Sight Gage

CAUTION: MAKE SURE THAT THERE IS NO CONTAMINATION ON THE OPENING

OF THE CONTAINER FROM WHICH YOU FILL THE OIL TANK.
(1) Add engine oil (Material Ref. CP2442) by pouring into oil tank fill port up to full mark.
SUBTASK 12-13-79-210-066-A
E. Before you install oil tank filler cap, ensure that the O'ring seal is in good condition or does
not show sign of leakage. If not, replace the O'ring seal Ref. AMM TASK 79-11-10-300-003.
SUBTASK 12-13-79-410-066-B
F. Close the Oil Tank.
Ref. Fig. Removal of the Oil Tank Filler Cap

WARNING: IF THE HANDLE POSITION IS OPPOSITE TO THE OIL QUANTITY

TRANSMITTER, THERE IS A RISK OF INJURY TO YOUR FINGERS.

WARNING: WHEN THE HANDLE OF THE FILLER CAP IS IN THE LOCKED

POSITION, MAKE SURE THAT IT CANNOT ACCIDENTALLY MOVE TO
ITS VERTICAL (UNLOCKED) POSITION. IF IT DOES, THERE IS A RISK
THAT PRESSURIZED HOT OIL WILL FLOW OUT OF THE TANK AND
CAUSE INJURY (DANGEROUS BURNS).

CAUTION: MAKE SURE THAT THE OIL TANK FILLER-CAP IS LOCKED. ITS
HANDLE MUST POINT TO THE OIL QUANTITY TRANSMITTER.

CAUTION: MAKE SURE THAT THE FILLER CAP IS CORRECTLY CLOSED. IF IT IS

NOT CORRECTLY CLOSED, A BAD SUPPLY PRESSURE OF THE OIL
LUBRICATION UNIT DURING ENGINE OPERATION CAN OCCUR.

CAUTION: DO NOT USE FORCE TO MOVE THE HANDLE OF THE FILLER CAP.
DAMAGE CAN OCCUR TO ITS LOCKING DEVICE.

CAUTION: DO NOT TRY TO PULL THE HANDLE OF THE FILLER CAP OUT OF ITS
STOP LIMITS.
(1) Install the oil tank filler cap with handle in vertical position.
(2) Turn the handle of the oil tank filler cap clockwise 45° against its stop to engage the
locking device.

NOTE: If the locking device is correctly engaged, the cap cannot be pulled from
tank.

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

(3) Push hinged oil tank cap handle down flat into the locked position.

5. Close-up
SUBTASK 12-13-79-410-065-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the oil tank access door :

(a) FOR 1000EM1 (ENGINE-1)

437BL
(b) FOR 1000EM2 (ENGINE-2)
447BL

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 6 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

B
B

Figure 12-13-79-991-30100-06-A (SHEET 1) - Oil Tank Sight Gage

** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 7 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

Figure 12-13-79-991-30500-06-A (SHEET 1) - Measuring the Viscosity of the Oil

** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 8 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

Figure 12-13-79-991-30000-06-B (SHEET 1/2) - Removal of the Oil Tank Filler Cap
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 9 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
12-13-79-610-002-A
Tail Number - MSN - TITLE: 12-13-79-03 CONF 06
FSN: 12-13-79-610-002-A - Check oil level and replenish Check Pop
ALL Out Indicator of EMCD (Electrical Master Chip Detector)

MECH. INSP.

1 2

C C
2

Figure 12-13-79-991-30000-06-B (SHEET 2/2) - Removal of the Oil Tank Filler Cap
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212, 215-215, 222-350, 401-450
© *** END OF CARD ***

JCP Title: 791000-02-AFL CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 10 of 10

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 A20-33-0950
EXTERIOR LIGHTS – TESTING AND INSPECTION

Detailed inspection (DI) of the lenses and/or operational

test (as applicable) of the following external lights

AMM Task 33-42-00-710-001

AMM Task 33-43-00-710-001
AMM Task 33-46-00-710-001
AMM Task 33-48-00-710-001
AMM Task 33-49-00-710-001
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-42-00-710-001-A
Tail Number - MSN - TITLE: 33-42-00-05 CONF 00
FSN:
ALL 33-42-00-710-001-A - Operational Test of the Landing Lights

MECH. INSP.
** ON A/C FSN ALL
TASK 33-42-00-710-001-A
Operational Test of the Landing Lights
FIN: 7LB 8LB

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN

POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO
PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN

POSITION ON THE LANDING GEAR. THIS WILL PREVENT
UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS
POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE
AIRCRAFT AND/OR EQUIPMENT.

WARNING: MAKE SURE THAT THERE ARE NO SIGNS OF FUEL

CONTAMINATION IN THE LANDING LIGHT ASSEMBLY.
IF YOU FIND FUEL CONTAMINATION, NO PERSON MUST OPERATE
THE LANDING LIGHT UNTIL:
- YOU REPAIR THE FUEL LEAK
- YOU REPLACE THE LANDING LIGHT ASSEMBLY.
IF YOU DO NOT OBEY THIS PRECAUTION, IGNITION OF THE
REMAINING FUEL IN THE LANDING LIGHT CAN OCCUR.

1. Reason for the Job

Self explanatory

2. Job Set-up Information

A. Fixtures, Tools, Test and Support Equipment

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 5

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-42-00-710-001-A
Tail Number - MSN - TITLE: 33-42-00-05 CONF 00
FSN:
ALL 33-42-00-710-001-A - Operational Test of the Landing Lights

MECH. INSP.

Q
REFERENCE T DESIGNATION
Y
No specific A SAFETY BARRIER(S)
R
No specific 1 WARNING NOTICE(S)

B. Referenced Information

REFERENCE DESIGNATION
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002-A External Power
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002- APU
A01
Ref. Energize the Aircraft Electrical Circuits from
24-41-00-861-002- Engine 1(2)
A02
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002-A Supplied from the External Power
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the APU
A01
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the Engine 1(2)
A02
** ON A/C FSN 551-650
Ref. Deactivation of Broadband System for
44-33-00-040-804-A Maintenance
Ref. Reactivation of Broadband System after
44-33-00-440-804-A Maintenance

** ON A/C FSN ALL

3. Job Set-up
SUBTASK 33-42-00-941-051-A

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 5

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-42-00-710-001-A
Tail Number - MSN - TITLE: 33-42-00-05 CONF 00
FSN:
ALL 33-42-00-710-001-A - Operational Test of the Landing Lights

MECH. INSP.

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified
by the operator's instructions and your local regulations.
(2) Put a WARNING NOTICE(S) in position on the panel 25VU to tell
persons not to operate the landing lights.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-42-00-861-050-A
B. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN 551-650
SUBTASK 33-42-00-861-050-B
B. Aircraft Maintenance Configuration

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A

RADIUS OF 29 METERS (96 FEET) AROUND AND
ABOVE THE BROADBAND ANTENNA, MAKE SURE
THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS
AND CAN CAUSE INJURY TO PERSONS.
(1) Deactivate the broadband antenna Ref. AMM TASK
44-33-00-040-804.
(2) Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN ALL
SUBTASK 33-42-00-865-050-A
C. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL DESIGNATION FIN LOCATION

LIGHTING/LANDING LT/R/
122VU 4LB T07
CTL
LIGHTING/LANDING LT/R/
122VU 2LB T06
SPLY
LIGHTING/LANDING LT/L/
122VU 3LB T05
CTL

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 5

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-42-00-710-001-A
Tail Number - MSN - TITLE: 33-42-00-05 CONF 00
FSN:
ALL 33-42-00-710-001-A - Operational Test of the Landing Lights

MECH. INSP.

PANEL DESIGNATION FIN LOCATION

LIGHTING/LANDING LT/L/
122VU 1LB T04
SPLY

4. Procedure
SUBTASK 33-42-00-710-050-A
A. Operational Test of the Landing Lights

CAUTION: DO NOT OPERATE THE RETRACTABLE LANDING

LIGHT 7LB (8LB) FOR MORE THAN ONE MINUTE
WHEN THE AIRCRAFT IS ON THE GROUND. THE
LANDING LIGHT CAN BECOME DAMAGED IF IT
OPERATES WITH NO AIRFLOW TO KEEP THE LIGHT
UNIT COOL. MAKE SURE THAT THERE IS A MINIMUM
PERIOD OF FIVE MINUTES BETWEEN EACH
OPERATION, TO LET THE TEMPERATURE OF THE
LIGHT UNIT DECREASE.
(1) Make sure that the travel range(s) of the applicable landing
light(s) is(are) clear.
(2) Do this test:

NOTE: This test is for the left landing light. For the right
landing light, use the indications in parenthesis.

ACTION RESULT
On panel 25VU: At zone 571(671):
1.Set the LAND L(LAND R) - the landing light extends
switch to OFF. fully in not more than 10
seconds.
2.Set the LAND L(LAND R) - the landing light comes
switch to ON. on.
3.Set the LAND L(LAND R) - the landing light goes off.
switch to OFF.
4.Set the LAND L(LAND R) - the landing light retracts
switch to RETRACT. in not more than 10
seconds.

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 5

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-42-00-710-001-A
Tail Number - MSN - TITLE: 33-42-00-05 CONF 00
FSN:
ALL 33-42-00-710-001-A - Operational Test of the Landing Lights

MECH. INSP.

ACTION RESULT
5.Set the LAND L(LAND R) - the landing light extends
switch to ON. - before the landing light is
fully extended, the light
comes on.
6.Set the LAND L(LAND R) - the landing light retracts
switch to RETRACT. - after the landing light
starts to retract, the light
goes off.

5. Close-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-42-00-862-050-A
A. Aircraft Maintenance Configuration
(1) De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.
** ON A/C FSN 551-650
SUBTASK 33-42-00-862-050-B
A. Aircraft Maintenance Configuration
(1) Reactivate the broadband antenna Ref. AMM TASK
44-33-00-440-804.
(2) De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.
** ON A/C FSN ALL
SUBTASK 33-42-00-942-051-A
B. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the WARNING NOTICE(S).
(3) Remove the ground support and maintenance equipment, the
special and standard tools and all other items.

© *** END OF CARD ***

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 5

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-43-00-710-001-A
Tail Number - MSN - TITLE: 33-43-00-05 CONF 00
FSN: 33-43-00-710-001-A - Operational Test of the Runway Turnoff
ALL Lights

MECH. INSP.
** ON A/C FSN ALL
TASK 33-43-00-710-001-A
Operational Test of the Runway Turnoff Lights
1. Reason for the Job
Make sure that the turnoff lights operate correctly.

2. Job Set-up Information

A. Referenced Information

REFERENCE DESIGNATION
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002-A External Power
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002- APU
A01
Ref. Energize the Aircraft Electrical Circuits from
24-41-00-861-002- Engine 1(2)
A02
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002-A Supplied from the External Power
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the APU
A01
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the Engine 1(2)
A02
** ON A/C FSN 551-650
Ref. Deactivation of Broadband System for
44-33-00-040-804-A Maintenance
Ref. Reactivation of Broadband System after
44-33-00-440-804-A Maintenance

** ON A/C FSN ALL

3. Job Set-up

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-43-00-710-001-A
Tail Number - MSN - TITLE: 33-43-00-05 CONF 00
FSN: 33-43-00-710-001-A - Operational Test of the Runway Turnoff
ALL Lights

MECH. INSP.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-43-00-861-051-A
A. Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN 551-650
SUBTASK 33-43-00-861-051-B
A. Aircraft Maintenance Configuration

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A

RADIUS OF 29 METERS (96 FEET) AROUND AND
ABOVE THE BROADBAND ANTENNA, MAKE SURE
THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS
AND CAN CAUSE INJURY TO PERSONS.
(1) Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
(2) Deactivate the broadband antenna Ref. AMM TASK
44-33-00-040-804.
** ON A/C FSN ALL
SUBTASK 33-43-00-865-050-A
B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL DESIGNATION FIN LOCATION

LIGHTING/EXT LT/TAXI
122VU 2LR W09
AND TAKE OFF/CTL
LIGHTING/EXT LT/RWY
122VU 1LC1 W06
TURN OFF/L
LIGHTING/EXT LT/RWY
122VU 1LC2 W05
TURN OFF/R

4. Procedure
SUBTASK 33-43-00-710-050-A
A. Operational Test of Lights

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-43-00-710-001-A
Tail Number - MSN - TITLE: 33-43-00-05 CONF 00
FSN: 33-43-00-710-001-A - Operational Test of the Runway Turnoff
ALL Lights

MECH. INSP.

ACTION RESULT
On the panel 25VU: On the nose landing gear:
- set the RWY TURN OFF - the runway turnoff lights
switch to ON, come on,
- set the RWY TURN OFF - the runway turnoff lights go
switch to OFF. off.

SUBTASK 33-43-00-862-051-A
B. De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.

5. Close-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-43-00-942-054-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other
items.
** ON A/C FSN 551-650
SUBTASK 33-43-00-942-054-B
A. Close Access
(1) Reactivate the broadband antenna Ref. AMM TASK
44-33-00-440-804.
(2) Make sure that the work area is clean and clear of tools and other
items.

© *** END OF CARD ***

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-46-00-710-001-A
Tail Number - MSN - TITLE: 33-46-00-05 CONF 00
FSN: 33-46-00-710-001-A - Operational Test of the Taxi and Take
ALL Off Lights

MECH. INSP.
** ON A/C FSN ALL
TASK 33-46-00-710-001-A
Operational Test of the Taxi and Take Off Lights
1. Reason for the Job
Make sure that the taxi and take off lights operate correctly.

2. Job Set-up Information

A. Referenced Information

REFERENCE DESIGNATION
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002-A External Power
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002- APU
A01
Ref. Energize the Aircraft Electrical Circuits from
24-41-00-861-002- Engine 1(2)
A02
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002-A Supplied from the External Power
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the APU
A01
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the Engine 1(2)
A02
** ON A/C FSN 551-650
Ref. Deactivation of Broadband System for
44-33-00-040-804-A Maintenance
Ref. Reactivation of Broadband System after
44-33-00-440-804-A Maintenance

** ON A/C FSN ALL

3. Job Set-up

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-46-00-710-001-A
Tail Number - MSN - TITLE: 33-46-00-05 CONF 00
FSN: 33-46-00-710-001-A - Operational Test of the Taxi and Take
ALL Off Lights

MECH. INSP.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-46-00-861-051-A
A. Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN 551-650
SUBTASK 33-46-00-861-051-B
A. Aircraft Maintenance Configuration

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A

RADIUS OF 29 METERS (96 FEET) AROUND AND
ABOVE THE BROADBAND ANTENNA, MAKE SURE
THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS
AND CAN CAUSE INJURY TO PERSONS.
(1) Deactivate the broadband antenna Ref. AMM TASK
44-33-00-040-804.
(2) Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN ALL
SUBTASK 33-46-00-865-050-A
B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL DESIGNATION FIN LOCATION

LIGHTING/EXT LT/TAXI
122VU 2LR W09
AND TAKE OFF/CTL
LIGHTING/EXT LT/TAXI
122VU 1LR W08
AND TAKE OFF/TAXI
LIGHTING/EXT LT/TAXI
122VU 3LR W07
AND TAKE OFF/TO

4. Procedure
SUBTASK 33-46-00-710-050-A
A. Operational test of Lights

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-46-00-710-001-A
Tail Number - MSN - TITLE: 33-46-00-05 CONF 00
FSN: 33-46-00-710-001-A - Operational Test of the Taxi and Take
ALL Off Lights

MECH. INSP.

ACTION RESULT
1.On the panel 25VU: On the nose landing gear:
- set the NOSE selector - the taxi light comes on,
switch to TAXI,
- set the NOSE selector switch to - the taxi and take off lights
TO, come on,
- set the NOSE selector switch to - the taxi and take off lights go
OFF. off.

5. Close-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-46-00-862-051-A
A. De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.
** ON A/C FSN 551-650
SUBTASK 33-46-00-862-051-B
A. Put the aircraft back to its initial configuration.
(1) Reactivate the broadband antenna Ref. AMM TASK
44-33-00-440-804.
(2) De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.

© *** END OF CARD ***

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-48-00-710-001-A
Tail Number - MSN - TITLE: 33-48-00-05 CONF 00
FSN: 33-48-00-710-001-A - Operational Test of the Anti-Collision
ALL Lighting

MECH. INSP.
** ON A/C FSN ALL
TASK 33-48-00-710-001-A
Operational Test of the Anti-Collision Lighting
FIN: 6LV 7LV

WARNING: DO NOT LOOK DIRECTLY AT THE LIGHT FLASH DURING THE

TEST.
SUPPLY A COVER, OR SHIELD, TO GIVE PROTECTION FROM THE
LIGHT FLASH TO PERSONS IN THE TEST AREA.

1. Reason for the Job

Make sure that the Beacon/Strobe Lights operate correctly.

2. Job Set-up Information

A. Referenced Information

REFERENCE DESIGNATION
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002-A External Power
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002- APU
A01
Ref. Energize the Aircraft Electrical Circuits from
24-41-00-861-002- Engine 1(2)
A02
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002-A Supplied from the External Power
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the APU
A01
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the Engine 1(2)
A02
** ON A/C FSN 551-650
Ref. Deactivation of Broadband System for
44-33-00-040-804-A Maintenance

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-48-00-710-001-A
Tail Number - MSN - TITLE: 33-48-00-05 CONF 00
FSN: 33-48-00-710-001-A - Operational Test of the Anti-Collision
ALL Lighting

MECH. INSP.

REFERENCE DESIGNATION
Ref. Reactivation of Broadband System after
44-33-00-440-804-A Maintenance

** ON A/C FSN ALL

3. Job Set-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-48-00-861-050-A
A. Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN 551-650
SUBTASK 33-48-00-861-050-B
A. Aircraft Maintenance Configuration

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A

RADIUS OF 29 METERS (96 FEET) AROUND AND
ABOVE THE BROADBAND ANTENNA, MAKE SURE
THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS
AND CAN CAUSE INJURY TO PERSONS.
(1) Deactivate the broadband antenna Ref. AMM TASK
44-33-00-040-804.
(2) Energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-861-002.
** ON A/C FSN ALL
SUBTASK 33-48-00-865-050-A
B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL DESIGNATION FIN LOCATION

LIGHTING/EXT LT/
122VU 1LV U06
BEACON/UPPER
LIGHTING/EXT LT/
122VU 5LV U03
BEACON/LOWER

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-48-00-710-001-A
Tail Number - MSN - TITLE: 33-48-00-05 CONF 00
FSN: 33-48-00-710-001-A - Operational Test of the Anti-Collision
ALL Lighting

MECH. INSP.

WARNING: DO NOT LOOK DIRECTLY AT THE LIGHT FLASH DURING THE

TEST.
SUPPLY A COVER, OR SHIELD, TO GIVE PROTECTION FROM THE
LIGHT FLASH TO PERSONS IN THE TEST AREA.
4. Procedure
SUBTASK 33-48-00-710-050-B
A. Test of the Anti-Collision/Strobe Lighting
(1) Do this test:

ACTION RESULT
1.On the overhead panel On the upper and lower
25VU: fuselage:
- Put the switch BEACON - The upper beacon light
2LV in the ON position. 7LV and the lower
beacon light 6LV come
on.
These lights flash at a rate of
55 +/- 5 flashes per minute.
2.On the overhead panel On the upper and lower
25VU: fuselage:
- Put the switch BEACON - The upper beacon light
2LV in the OFF position. 7LV and the lower
beacon light 6LV go off.

5. Close-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-48-00-862-050-A
A. De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.
** ON A/C FSN 551-650
SUBTASK 33-48-00-862-050-B
A. Aircraft Maintenance Configuration
(1) De-energize the aircraft electrical circuits Ref. AMM TASK
24-41-00-862-002.

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-48-00-710-001-A
Tail Number - MSN - TITLE: 33-48-00-05 CONF 00
FSN: 33-48-00-710-001-A - Operational Test of the Anti-Collision
ALL Lighting

MECH. INSP.

(2) Reactivate the broadband antenna Ref. AMM TASK

44-33-00-440-804.

© *** END OF CARD ***

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 4

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-49-00-710-001-A
Tail Number - MSN - TITLE: 33-49-00-05 CONF 00
FSN: 33-49-00-710-001-A - Operational Test of the Wing and
ALL Engine Scan Lights

MECH. INSP.
** ON A/C FSN ALL
TASK 33-49-00-710-001-A
Operational Test of the Wing and Engine Scan Lights
1. Reason for the Job
Make sure that the wing/engine scan lights operate correctly.

2. Job Set-up Information

A. Referenced Information

REFERENCE DESIGNATION
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002-A External Power
Ref. Energize the Aircraft Electrical Circuits from the
24-41-00-861-002- APU
A01
Ref. Energize the Aircraft Electrical Circuits from
24-41-00-861-002- Engine 1(2)
A02
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002-A Supplied from the External Power
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the APU
A01
Ref. De-energize the Aircraft Electrical Circuits
24-41-00-862-002- Supplied from the Engine 1(2)
A02
** ON A/C FSN 551-650
Ref. Deactivation of Broadband System for
44-33-00-040-804-A Maintenance
Ref. Reactivation of Broadband System after
44-33-00-440-804-A Maintenance

** ON A/C FSN ALL

3. Job Set-up

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-49-00-710-001-A
Tail Number - MSN - TITLE: 33-49-00-05 CONF 00
FSN: 33-49-00-710-001-A - Operational Test of the Wing and
ALL Engine Scan Lights

MECH. INSP.
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-49-00-861-051-A
A. Energize the aircraft electrical circuits
Ref. AMM TASK 24-41-00-861-002.
** ON A/C FSN 551-650
SUBTASK 33-49-00-861-051-B
A. Aircraft Maintenance Configuration

WARNING: BEFORE YOU DO MAINTENANCE WORK WITHIN A

RADIUS OF 29 METERS (96 FEET) AROUND AND
ABOVE THE BROADBAND ANTENNA, MAKE SURE
THAT THE ANTENNA IS DE-ENERGIZED. THE
ANTENNA USES HIGH POWER WHEN IT TRANSMITS
AND CAN CAUSE INJURY TO PERSONS.
(1) Deactivate the broadband antenna Ref. AMM TASK
44-33-00-040-804.
(2) Energize the aircraft electrical circuits
Ref. AMM TASK 24-41-00-861-002.
** ON A/C FSN ALL
SUBTASK 33-49-00-865-050-A
B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL DESIGNATION FIN LOCATION

LIGHTING/EXT LT/WING/
122VU 1LX W03
AND ENG SCAN/R
LIGHTING/EXT LT/WING/
122VU 5LX W02
AND ENG SCAN/L

4. Procedure
SUBTASK 33-49-00-710-050-A
A. Operational Test of the Wing and Engine Scan Lights

ACTION RESULT
1.On the panel 25VU: From each side of the fuselage:

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE
 REV DATE: Nov
JOB CARD
01/2020
AMM - AFL - A318/A319/A320/A321 TASK:
33-49-00-710-001-A
Tail Number - MSN - TITLE: 33-49-00-05 CONF 00
FSN: 33-49-00-710-001-A - Operational Test of the Wing and
ALL Engine Scan Lights

MECH. INSP.

ACTION RESULT
- set the EXT LT/WING - the wing/engine scan-lights
selector switch to ON, come on,
- set the EXT LT/WING - the wing/engine scan lights
selector switch to OFF. go off.

5. Close-up
** ON A/C FSN 001-050, 116-117, 122-125, 128-150, 152-200, 211-212,
215-215, 222-350, 401-450
SUBTASK 33-49-00-862-051-A
A. De-energize the aircraft electrical circuits
Ref. AMM TASK 24-41-00-862-002.
** ON A/C FSN 551-650
SUBTASK 33-49-00-862-051-B
A. Put the aircraft back to its initial configuration.
(1) Reactivate the broadband antenna Ref. AMM TASK
44-33-00-440-804.
(2) De-energize the aircraft electrical circuits
Ref. AMM TASK 24-41-00-862-002.

© *** END OF CARD ***

JCP Title: A20-33-0950 CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 3

PRINT DATE: Nov 03/2020
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN
COMPLETED TO THE REQUIRED STANDARD AND SUPPORTS
THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF
RELEASE TO SERVICE