Length Width Height MASS (Each) Total Mass LCG TCG VCG Maximum Force Seafastening Type

ITEM DESCRIPTION QTY. Cargo Strap D-Ring Max UC Remark

(m) (m) (m) (Te) (Te) (m) (m) (m) Transv (Te) Long (Te) Vert (Te) Dog Plate/Stopper
(WLL) (WLL)/Padeye
1 LARS 5.4 3.7 3.7 1 6 6 18.5 8.7 7.04 0.759 0.794 6.789 12mm (min. 3nos each side) 0.13 Pass
2 Container 20ft 6.1 2.44 2.59 2 8 16 11.40 7.3 6.21 0.972 0.971 8.952 12mm (min. 2nos each side) 0.20 Pass
Generator, Compressor
3 6.1 2.44 2 1 10 10 25.90 7.3 5.77 1.215 1.454 11.44 12mm (min. 2nos each side) 0.19 Pass
and Fabrication Equipment
4 Concrete Mattress 6.02 2.4 0.35 1 32 32 15.00 2 4.26 3.293 4.040 36.01 12mm T-Bar (min. 2nos each side) 5Te 5Te 0.43 Pass

Typical Dog Plate Design Typical T-Bar Design

Dimension of Stopper
A= 200 mm Dimension of Stopper
B= 207 mm A= 100 mm
C= 215 mm B= 100 mm
D= 140 mm C= 12 mm
E= 18 mm (to be adjusted on site) D= 12 mm
tp = 12 mm d= 100 mm Length of base frame
Fy = 248 Mpa yield strength of plate material Fy = 248 Mpa yield strength of plate material
Fw = 480 Mpa yield strength of weld material Fw = 480 Mpa yield strength of weld material
GENERATOR SEAFASTENING
1.0 Scope

This worksheet assesses the adequacy of the stopper plate

for effective supporting of loads from the Generator in
accordance with API RP 2A - WSD (21st Edition).

2.0 Input Particulars

FH 2.72 MT Horizontal force

g 9.807 m/s^2
n 2 total stopper

Fh = g*FH/n total horizontal force on each stopper

13.31 kN

Dimension of Stopper
A= 200 mm
B= 207 mm
C= 215 mm
D= 140 mm
E= 18 mm
tp = 12 mm
Fy = 248 Mpa yield strength of plate material
Fw = 480 Mpa yield strength of weld material

3.0 Calculations

3.1 Strength Check

Shear Plane

Shear plane A1 = A*D 2400 mm^2

Allowable Shear stress fv = 0.4Fy 99.20 Mpa

Shear Stres σ.1 = F.h/A.1 5.55 MPa

UC.s σ.1/f.v 0.06

Bending Check

Inplane Bending Moment M= Fh*(B*0.75) 2066.89 kN.mm

Inplane Section Modulus Sxx = 80000 mm^3
Bending stress τ.1 = M/S.xx 25.84 MPa
Allowable bending stress fb = 0.66*F.y 163.68 MPa

UC.b = τ.1/f.b 0.16

Combined Stress Check

2 2
Combines stress σ.comb1:= 3 σ+
.1 τ.1

σ.comb1 = 27.56 Mpa

Allowable Combine Stress f.c = 0.6*F.y 148.8 Mpa

UC.c = σ.comb1/f.c 0.19

3.2 Strength Check on Weld

Shear Stress

Weld size Sw = 10 mm

Weld throat size Ew = 0.707*Sw

7.07 mm
Allowable Stress on weld fw = 0.3Fw
144 Mpa
Weld Length Lw = A*2
400 mm
Shear Stress F.ws = F.h/L.w*E.w
4.71 MPa

Bending stress

Allowable bending stress on Weldf.bw = 0.3*Fw

144 Mpa
Moment Inertia I.xy = 537781.7 mm^4

Section Modulus
SMy = 82292.54 mm^3

Bending Stress (weld) Fb = M/SMy 25.12 Mpa

UC = 0.17

Combined Stress Check

Combines stress σ.wcomb = 26.41 Mpa

Allowable Combine Stress f.wcomb = 0.3*F.w 144 Mpa

UC.cw = σ.wcomb/f.wcomb 0.18

CONTAINER SEAFASTENING
1.0 Scope

This worksheet assesses the adequacy of the stopper plate

for effective supporting of loads from the Container in
accordance with API RP 2A - WSD (21st Edition).

2.0 Input Particulars

FH 2.97 MT Horizontal force

g 9.807 m/s^2
n 2 total stopper

Fh = g*FH/n total horizontal force on each stopper

14.57 kN

Dimension of Stopper
A= 200 mm
B= 207 mm
C= 215 mm
D= 140 mm
E= 18 mm (to be adjusted on site)
tp = 12 mm
Fy = 248 Mpa yield strength of plate material
Fw = 480 Mpa yield strength of weld material

3.0 Calculations

3.1 Strength Check

Shear Plane

Shear plane A1 = A*D 2400 mm^2

Allowable Shear stress fv = 0.4Fy 99.20 Mpa

Shear Stres σ.1 = F.h/A.1 6.07 MPa

UC.s σ.1/f.v 0.06

Bending Check

Inplane Bending Moment M= Fh*(B*0.75) 2262.53 kN.mm

Inplane Section Modulus Sxx = 80000 mm^3
Bending stress τ.1 = M/S.xx 28.28 MPa
Allowable bending stress fb = 0.66*F.y 163.68 MPa

UC.b = τ.1/f.b 0.17

Combined Stress Check

2 2
Combines stress σ.comb1:= 3 σ+
.1 τ.1

σ.comb1 = 30.17 Mpa

Allowable Combine Stress f.c = 0.6*F.y 148.8 Mpa

UC.c = σ.comb1/f.c 0.20

3.2 Strength Check on Weld

Shear Stress

Weld size Sw = 10 mm

Weld throat size Ew = 0.707*Sw

7.07 mm
Allowable Stress on weld fw = 0.3Fw
144 Mpa
Weld Length Lw = A*2
400 mm
Shear Stress F.ws = F.h/L.w*E.w
5.15 MPa

Bending stress

Allowable bending stress on Weldf.bw = 0.3*Fw

144 Mpa
Moment Inertia I.xy = 537781.7 mm^4

Section Modulus
SMy = 82292.54 mm^3

Bending Stress (weld) Fb = M/SMy 27.49 Mpa

UC = 0.19

Combined Stress Check

Combines stress σ.wcomb = 28.91 Mpa

Allowable Combine Stress f.wcomb = 0.3*F.w 144 Mpa

UC.cw = σ.wcomb/f.wcomb 0.20

T-BAR for MATTRESS
1.0 Scope
This worksheet assesses the adequacy of the stopper plate for effective supporting of
loads from the Container in accordance with API RP 2A - WSD (21st Edition).

2.0 Input Particulars

FH = 5.29 MT Horizontal force
FL = 6.04 MT Longitudinal force
g= 9.807 m/s^2
n= 2 total stopper

Fh = g*FH/n total horizontal force on each stopper

25.95 kN
Fl = g*FL/n total Longitudinal force on each stopper
29.62 kN

Dimension of Stopper
A= 100 mm
B= 100 mm
C= 12 mm
D= 12 mm
d= 100 mm Length of base frame
Fy = 248 Mpa yield strength of plate material
Fw = 480 Mpa yield strength of weld material

3.0 Calculations

Strength Check
Shear Check

Shear plane A1 = (A+C)*D 1344 mm^2

Allowable Shear stress fv = 0.4Fy 99.20 Mpa

Shear Stres σ.1 = F.h/A.1 19.31 MPa

UC.s σ.1/f.v 0.19

Bending Check

Inplane Bending Moment M= Fh*(d) 2595.24 kN.mm

Inplane Section Modulus Sxx 47718 mm^3

Bending stress τ.1 = M/S.xx 54.39 MPa

Allowable bending stress fb = 0.66*F.y 163.68 MPa

UC.b = τ.1/f.b 0.33

Combined Stress Check

2 2
Combines stress σ.comb1:= 3 σ+
.1 τ.1

σ.comb1 = 63.85 Mpa

Allowable Combine Stress f.c = 0.6*F.y 148.8 Mpa

UC.c = σ.comb1/f.c 0.43

3.1 Strength Check on Weld

Shear Stress

Weld size Sw = 7 mm

Weld throat size Ew = 0.707*Sw

4.95 mm
Allowable Stress on weld fw = 0.3Fw
144 Mpa
Weld Length Lw = A*2
200 mm
Shear Stress F.ws = F.h/L.w*E.w
26.22 MPa

Bending stress

Allowable bending stress on Weldf.bw = 0.3*Fw

144 Mpa
Moment Inertia I.xy = 175009.7 mm^4

Section Modulus
SMy = 31968.16 mm^3
Bending Stress (weld) Fb = M/SMy 81.18 Mpa
UC = 0.56

Combined Stress Check

Combines stress σ.wcomb = 93.02 Mpa

Allowable Combine Stress f.wcomb = 0.3*F.w 144

UC.cw = σ.wcomb/f.wcomb 0.65

LARS SEAFASTENING
1.0 Scope

This worksheet assesses the adequacy of the stopper plate

for effective supporting of loads from the Diving Lars in
accordance with API RP 2A - WSD (21st Edition).

2.0 Input Particulars

FH 2.76 MT Horizontal force + Wind Force

g 9.807 m/s^2
n 3 total stopper

Fh = g*FH/n total horizontal force on each stopper

9.02 kN

Dimension of Stopper
A= 200 mm
B= 207 mm
C= 215 mm
D= 140 mm
E= 18 mm
tp = 12 mm
Fy = 248 Mpa yield strength of plate material
Fw = 480 Mpa yield strength of weld material

3.0 Calculations

3.1 Strength Check

Shear Plane

Shear plane A1 = A*D 2400 mm^2

Allowable Shear stress fv = 0.4Fy 99.20 Mpa

Shear Stres σ.1 = F.h/A.1 3.76 MPa

UC.s σ.1/f.v 0.04

Bending Check

Inplane Bending Moment M= Fh*(B*0.75) 1399.99 kN.mm

Inplane Section Modulus Sxx = 80000 mm^3
Bending stress τ.1 = M/S.xx 17.50 MPa
Allowable bending stress fb = 0.66*F.y 163.68 MPa

UC.b = τ.1/f.b 0.11

Combined Stress Check

2 2
Combines stress σ.comb1:= 3 σ+
.1 τ.1

σ.comb1 = 18.67 Mpa

Allowable Combine Stress f.c = 0.6*F.y 148.8 Mpa

UC.c = σ.comb1/f.c 0.13

3.2 Strength Check on Weld

Shear Stress

Weld size Sw = 8 mm

Weld throat size Ew = 0.707*Sw

5.66 mm
Allowable Stress on weld fw = 0.3Fw
144 Mpa
Weld Length Lw = A*2
400 mm
Shear Stress F.ws = F.h/L.w*E.w
3.99 MPa

Bending stress

Allowable bending stress on Weldf.bw = 0.3*Fw

144 Mpa
Moment Inertia I.xy = 364696.4 mm^4

Section Modulus
SMy = 62576.59 mm^3

Bending Stress (weld) Fb = M/SMy 22.37 Mpa

UC = 0.16

Combined Stress Check

Combines stress σ.wcomb = 23.41 Mpa

Allowable Combine Stress f.wcomb = 0.3*F.w 144 Mpa

UC.cw = σ.wcomb/f.wcomb 0.16

 Bending Stress = 61.63 N/mm2 Stress Ratio 0.381 OK !
CLIENT : Pertamina BY : DBP
12 Check Tension / Compression of Base Material @ Welding Toe
CONTRACT : CHECK : AFS
Tension / Comp Stress = 20.42 N/mm2 Stress Ratio 0.139 OK !
SUBJECT : Padeye Check DATE : 10-Jan-22
13 Check Shear Stress of Base Material @ Welding Toe
Shear Stress = 11.79 N/mm2 Stress Ratio 0.120 OK !
P
Padeye on Stanchion Design R
14 Check Von Mises Stress of Base Material @ Welding Toe
INPUT: Ø Von Mises Stress = 84.55 N/mm2 Stress Ratio 0.383 OK !

Main Plate Thickness t 25 mm
15 Check 10% Side Force Section Modulus of Bracket 25500 mm3 =1/6 x 1 x 170 x 30^2
Length L 160 mm
Additional Bending Stress 19.24 N/mm2 @weak axis
Hole Distance A 45 mm
Vertical Distance V 100 mm Von Mises Stress = 62.81 N/mm2 Stress Ratio 0.285 OK !

Pin Diameter Phai 28 mm

Outer Radius R 45 mm Thk V
Welding Toe tw 6.5 mm
Yielding Y for Main Plate 245 N/mm2
A
Yielding Y for Welding Material 400 N/mm2
tw L
Yielding Y for Base Material 245 N/mm2
Loading P 49.05 KN 5.0 MT (x2 lashing tension)
Loading Angle Alpha 60 degree
Safety Factor Ksf 1.0 Actually, Loading P already considered Safety Factor of 2.0 in Analysis
For PadEye Main Plate For Welding Material For Base Material
Allowable Bearing Stress 220.5 N/mm2
Allowable Bending Stress 161.7 N/mm2 264 N/mm2 161.7 N/mm2 0.66 Y
Allowable T/C Stress 147 N/mm2 240 N/mm2 147 N/mm2 0.6 Y
Allowable VM Stress 220.5 N/mm2 360 N/mm2 220.5 N/mm2 0.9 Y
Allowable Shear Stress 98 N/mm2 160 N/mm2 98 N/mm2 0.4 Y

Maximum Unity Check 0.404 OK ! NO 1/3 Increasment Applied

1 Check Bearing
Bearing Stress = 89.18 N/mm2 Stress Ratio 0.404 OK !

2 Check tear along hole

Shear Stress = 31.65 N/mm2 Stress Ratio 0.323 OK !

3 Check Bending @ Main Plate Bottom

Bending Stress = 32.05 N/mm2 Stress Ratio 0.198 OK !

4 Check Tension / Compression @ Main Plate Bottom

Tension / Comp Stress = 10.62 N/mm2 Stress Ratio 0.072 OK !

5 Check Shear Stress @ Main Plate Bottom

Shear Stress = 6.13 N/mm2 Stress Ratio 0.063 OK !

6 Check Von Mises Stress @ Main Plate Bottom

Von Mises Stress = 43.97 N/mm2 Stress Ratio 0.199 OK !

7 Check Bending @ Main Plate Bottom Welding Toe

Bending Stress = 87.15 N/mm2 Stress Ratio 0.330 OK !

8 Check Tension / Compression @ Main Plate Bottom Welding Toe

Tension / Comp Stress = 28.88 N/mm2 Stress Ratio 0.120 OK !

9 Check Shear Stress @ Main Plate Bottom Welding Toe

Shear Stress = 16.67 N/mm2 Stress Ratio 0.104 OK !

10 Check Von Mises Stress @ Main Plate Bottom Welding Toe

Von Mises Stress = 119.58 N/mm2 Stress Ratio 0.332 OK !

11 Check Bending of Base Material @ Welding Toe