15 Frame

Plunger Pump

Standard Brass
Model 650

FEATURES SPECIFICATIONS U.S. Measure Metric Measure

● Triplex design delivers high efficiency and low pulsation. Flow.......................................................................7.0 gpm (27 lpm)
● Durable V-Packings are lubricated and cooled by the liquid being Pressure Range....................................100 to 3000 psi (7 to 210 bar)
RPM.....................................................................1000 rpm (1000 rpm)
pumped.
Inlet Pressure Range...............................–5 to +60 psi (–0.35 to +4 bar)
● Pre-set Lo-Pressure Seals provide secondary protection against Bore.................................................................. .787" (20 mm)
external leaks and require no packing adjustment. Stroke..............................................................1.181" (30 mm)
● Special high-density, polished, concentric plungers provide a true Crankcase Capacity.....................................42 oz. (1.26 l)
wear surface and extended seal life. Maximum Liquid Temperature...............160°F (71°C)
Above 130F call Cat Pumps for inlet conditions and elastomer recommendations.
Inlet Ports (2).........................................3/4" NPTF (3/4" NPTF)
Discharge Ports (2)..............................1/2" NPTF (1/2" NPTF)
Pulley Mounting................................ Either Side (Either Side)
Shaft Diameter........................................... 1.181" (30 mm)
Weight............................................................44 lbs. (19.9 kg)
Dimensions......................16.28x12.99x6.44" (413.50x330x163.50 mm)

ELECTRIC HORSEPOWER REQUIREMENTS

FLOW PRESSURE MOTOR PULLEY SIZE
psi psi psi Using 1725 rpm Motor
2000 2500 3000 10" O.D. Pump Pulley
U.S. bar bar bar Pulley
gpm rpm
lpm 140 175 210 O.D.
7.0 27 9.6 12.0 14.4 1000 5.7
6.0 23 8.2 10.3 12.4 858 4.9
All High Pressure Systems require a primary pressure regulating device (i.e. regulator,
unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure 5.0 19 6.9 8.6 10.3 715 4.1
to install such relief devices could result in personal injury or damage to pump or
property. CAT PUMPS does not assume any liability or responsibility for the operation
of a customer’s high pressure system.
DETERMINING Rated gpm = “Desired” gpm
Read all CAUTIONS and WARNINGS before commencing service or operation of any THE PUMP R.P.M. Rated rpm “Desired” rpm
high pressure system. The CAUTIONS and WARNINGS are included in each service
DETERMINING gpm x psi = Electric Brake
manual and with each Accessory Data sheet. CAUTIONS and WARNINGS can also be
viewed online at www.catpumps.com/cautions-warnings or can be requested directly THE REQUIRED H.P. 1460 H. P. Required
from CAT PUMPS. DETERMINING Motor Pulley O.D. = Pump Pulley O.D.
MOTOR PULLEY SIZE Pump rpm Motor rpm

See complete Drive Packages [Inclds: Pulleys, Belts, Hubs, Key] Tech Bulletin 003.
Refer to pump Service Manual for repair procedure and additional technical information.
 PARTS LIST
ITEM PART NUMBER MATL DESCRIPTION QTY
2 30067 STL Key (M8x7.5x25) 1
5 92519 STZP Screw, HHC (M6x16) 8
8 43496 AL Cover, Bearing 2
9 815281 FBR Split Shim, Bearing Cover, 2 Pc. 2
10 11340 NBR O-Ring, Bearing Case - 70D 2
11 43495 NBR Seal, Oil, Crankshaft - 70D 2
15 39060 STL Bearing, Roller 2
20 48600 TNM Rod Assy, Connecting [11/00] 3
25 43494 FCM Crankshaft - Dual End 1
31 828710 PE Protector, Oil Cap w/Foam Gasket 1
32 43211 ABS Cap, Oil Filler 1
33 14177 NBR O-Ring, Filler Cap - 70D 1
37 92241 — Gauge, Oil, Bubble w/Gasket - 80D 1
38 44428 NBR Gasket, Flat, Oil Gauge - 80D 1
40 92520 STZP Screw, Sems HHC (M6x20) 4
48 25625 STCP Plug, Drain (1/4"x19BSP) 1
49 23170 NBR O-Ring, Drain Plug - 70D 1
50 43491 AL Cover, Rear 1
51 44834 NBR O-Ring, Rear Cover - 70D 1
53 115471 AL Crankcase w/Guide Pins 1
54 27488 S Pin, Guide 2
56 44664 POP Pan, Oil 1
64 43507 CM Pin, Crosshead 3
65 43501 SZZ Rod, Plunger 3
69 126592 STCP R Washer, Seal 3
70 43500 NBR Seal, Oil, Crankcase - 80D 3
75 43506 S Slinger, Barrier 3
88 45675 S Washer, Keyhole 3
89 43505 BB Spacer, Plunger 3
90 43300 CC Plunger (M20x77) 3
96 43235 PTFE Back-up-Ring, Plunger Retainer 3
97 17399 NBR O-Ring, Plunger Retainer - 80D 3
14160 FPM O-Ring, Plunger Retainer - 80D 3
◆ 46204 EPDM O-Ring, Plunger Retainer - 70D 3
98 45891 CU Gasket, Plunger Retainer 3
99 104360 S Retainer w/stud, Plunger (M5) 3
100 855001 POP Retainer, Seal (See Tech Bulletin 098) 3
101 43508 — Wick, Long Tab 3
106 44071 NBR Seal, LPS w/SS-Spg 3
44381 FPM Seal, LPS w/S-Spg 3
701974 SFTB Seal, LPS w/NIH-Spg 3
120 49291 BB Case, Seal [07/05] 3
121 14762 NBR O-Ring, Seal Case - 70D 3
11737 FPM O-Ring, Seal Case - 75D 3
◆ 46205 EPDM O-Ring, Seal Case 3
126 43515 BB Adapter, Female [01/04] 3
127 44607 STG V-Packing 6
44386 FPM V-Packing 6
128 43517 BB Adapter, Male 3
139 20326 BBCP Plug, Inlet (3/4" NPT) 1
162 43248 PTFE Back-up-Ring, Seat 6
163 43249 NBR O-Ring, Seat - 80D 6
44383 FPM O-Ring, Seat - 70D 6
◆ 46206 EPDM O-Ring, Seat - 70D 6
164 43722 S Seat 6
166 43721 S Valve 6
167 43751 S Spring 6
168 44564 PVDF Retainer, Spring 6
172 17617 NBR O-Ring, Valve Plug - 90D 6
11691 FPM O-Ring, Valve Plug - 90D 6
◆ 46207 EPDM O-Ring, Valve Plug - 70D 6
174 43851 BBCP Plug, Valve 6
43850 BB Plug, Valve 6
185 45975 NAB Head, Manifold 1
187 126545 STCP R Stud (M10x45) 4
192 126231 STCP R Lockwasher (M10) 4
194 126522 STCP R Nut, Hex (M10) 4
250 30764 NY Protector, Shaft w/2 Screws 1
255 30264 STZP Mount, Direct 1
260 30613 STZP R Mount, Rail Assy - A (30635,30903,30921,30912) 1
990550 STZP R Mount, Rail (Required on Diesel/Gas) 1
269 30206 F Pulley (10") [See Tech Bulletin 003] 1
274 30059 STL Hub, “H” (M30) (Keyway M8) [See Tech Bulletin 003] 1
283 34334 — Kit, Oil Drain (3/8"x24") 1
299 814561 BB Head, Complete 1
300 30798 NBR* Kit, Seal (Inclds: 97,100,106,121,127) 1
31033 FPM Kit, Seal (Inclds: 97,100,106,121,127) 1
◆ 33919 EPDM* Kit, Seal (Inclds: 97,100,106,121,127) 1
 EXPLODED VIEW

Model
Brass - 650
July 2012
ITEM PART NUMBER MATL DESCRIPTION QTY
310 30820 NBR Kit, Valve (Inclds: 162,163,164,166,167,168,172) 2
31263 FPM Kit, Valve (Inclds: 162,163,164,166,167,168,172) 2
◆ 31259 EPDM Kit, Valve (Inclds: 162,163,164,166,167,168,172) 2
350 30696 STZP Plier, Reverse 1
351 43523 STZP Tool, Seal Case Removal 1
33006 STZP Socket, Seal Case 1/2" Drive 1
352 44050 STZP Tool, Oil Gauge Removal 1
6107 — Oil, Bottle (21 oz.) ISO 68 Hydraulic 2
(Fill to specified crankcase capacity prior to start-up)
6575 — Plunger Pump Service DVD 1

Italics are optional items.  ◆ Silicone oil/grease required.

[ ] Date of latest production change.  R Components comply with RoHS Directive.
See Tech Bulletins 002, 003, 024, 027, 035, 036, 043, 045, 048, 049, 052, 053, 062, 074, 077,083 and 098 for additional information.
MATERIAL CODES (Not Part of Part Number):  ABS=ABS Plastic AL=Aluminum  BB=Brass  BBCP=Brass/Chrome Plated  CC=Ceramic  CM=Chrome-Moly
CU=Copper  EPDM=Ethylene Propylene Diene Monomer  F=Cast Iron  FBR=Fiber  FCM=Forged Chrome-Moly  FPM=Fluorocarbon  NAB=Nickel Aluminum Bronze
NBR=Medium Nitrile (Buna-N)  NY=Nylon PE=Polyethylene POP=Polypropylene PTFE=Pure Polytetrafluoroethylene PVDF=Polyvinylidene Fluoride S=304SS
SFTB=Special Blend PTFE Black  SHS=304SS/High Strength  STCP=Steel/Chrome Plated  STG=Special Blend PTFE White  STL=Steel  STZP=Steel/Zinc Plated
SZZ=304SS/Zamak  TNM=Special High Strength
 12.99 (330) 16.28 (413.50)

12.60 (320)
5.08 (129) 9.65 (245)
9.59 (243.50)
(2)- 1/2" NPTF
DISCHARGE
2.28
(58)
1.22 (31)
6.44
(163.50) 1.30 (33)
.315 (8)
3.54
(90) 1.181 (30)
5.28 (134)

.39 (10)
(2) - 3/4" NPTF INLET .59 (15) 2X 1.38 (35)
2.18 .78 (20)
4 - M10x1.5 1.95 (50) 4 - ø11
(55.40) .043 (11) 18 DEEP

2.05 (52)
3.46 (88) 2 SLOTS 6.69 (170)
4.17 (106) 6.58 (167) 1.07
(27)
6.06 (154) 11.81 (300)

Model 650

2
4

5 3

2 4

1 Special concentric, high density, polished, 3 100% wet seal design adds to service life by 5 Specially formulated, Cat Pump exclusive,
solid ceramic plungers provide a true wear allowing pumped liquids to cool and V-Packing offer unmatched performance
surface and extended seal life. lubricate on both sides. and seal life.
2 Manifolds are a high tensile strength 4 Stainless steel valves, seats and springs
bronze for long term, continuous duty and provide corrosion-resistance, ultimate
corrosion resistance. seating and extended life.

CAT PUMPS
1681 - 94TH LANE N.E. MINNEAPOLIS, MN 55449-4324
PHONE (763) 780-5440 — FAX (763) 780-2958
e-mail: [email protected]
www.catpumps.com

For International Inquiries go to www.catpumps.com and navigate to the “Contact Us” link. PN 993298 Rev C 7/12 12295