Cura Software User Manual

1.Installation of Cura14.07 .......................................................................................................1

1.1 File location in the TF card ...........................................................................................2

2. Cura Setting ........................................................................................................................ 9

2.1 Clear platform .......................................................................................................... ..9

2.2 Layer height settings ...................................................................................................13

2.3 Expert Setting .......................................................................................................... .21

0
 Cura Software

1.Installation of Cura14.07

a: Where can I find the software?

1) TF card with shipment;

2) download from Internet; b: Installation process

1) From TF card with shipment

Insert TF card and open the file

1
 1.1 File location in the TF card
1)Insert TF card , open the file

2) Download from Internet

Official Website：https://ultimaker.com/en/cura-software/list

2
Choose corresponding software to download

3
 .
b.Software Installation Process

1. Installation
Please wait for installation Positioning

2. Click Next

Choose 3 options below

1
2
3

1.Click Next

4. Click Install

4
 1.Installation Success

2.Click to finish

Installation complete

Click Next

5
1.Choose to run Cura

2. Click to finish

Click Next

6
 This is A8 parameter
1.Choose other to customize

You can customize name here.

We 2default
.Choose this data
these option
.
You can fill in according to
actual condition

1.Choose to customize

Choose this option

DO NOT choose this option !!!

3.Click Next
1.Click
2.ClicktoNext
finish

7
Now you have finished the installation. Next , enter Cura .

8
2. Cura Setting

2.1 Clear platform

Delete the dog. Two ways for you :

1.Move mouse to dog ,right click, click “delete object”.

2.Left click “File” , choose ”Clear platform”.

9
 Switch to full settings
for parameter setting

Open file：A8 Cura 14.07.ini

10
Position of configuration file: Computer/TF card)/ configuration file for cura-14.07

（suggestion :keep this file copy to your computer）

After Loading,the basic and advanced

configuration will be changed to the A8
regular printing configuration.

11
If print once at a time , it will influence the printing
quality, even cause damage to priner. So please
choose “Printer at once”.

12
2.2 Layer height settings

Layer height ： 0.1mm cost long time but have the best
printing precision. 0.2mm cost half time compared to
0.1mm , but have general printing precision. 0.3 cost less
time with not good precision. It defaults 0.2mm.

Left：0.1mm Right：0.2mm
Layer height Layer height

Layer height setting

0.8mm

1.2mm
Shell thickness setting

2mm
0.8mm is too thin for shell, 2mm shell 13
costs more time , 1.2mm is relatively
better. Please use the integer mutiple
of nozzle diameter.
 The Blue line is
the leak filament

Enable retraction

Enable retraction to avoid filaments

leakage when nozzles move in
empty area

Bottom/Top thickness: 1.2mm

Under the same
fill density

When fill density is less than 20%,

it’s easy for 0.6mm thickness to
cause hollow on the top. 1.2mm
normally won’t have this issue. Bottom/Top thickness: 0.6mm
14
Bottom/Top thickness setting

Fill Density
20%
Setting

50%

Fill Density: If strength requirement

is not so high , set 10% is ok.
Please improve fill density when
strength requirement gets higher.
Printing time will go up as well.

90%

Printing Speed setting

This is default speed. If other settings aren’t changed,

it prints more accurately while the printing process
takes more time.
High printing speed takes less time while it cannot
print accurately , making the model have bad quality.
Normally 40-60 print speed is suitable for printing.

Pringting Temperature

PLA filament temperature setting: nozzle: 190-210 ℃ hotbed: 40-60℃

ABS filament temperature setting: nozzle: 230-250℃ hotbed: 60-90℃

15
 Original Model Support type: None

Support type setting Support type: Touching Support type: Everywhere

Attention: Normally we add support to complex model or model with vacant parts. It
may have influence on the surface if you choose everywhere. You’d better circle
around the model and try to avoid unnecessary support.

16
Support setting

17
 None: no support

Brim:Touch with the adge

Raft: Totally touch with the bottom

Attention: please choose None if the printing platform is ready and the high temperature adhesive
tape is good. Please choose Brim when the model is small . Choosing Raft makes it difficult to
seperate model from the platform

18
 Attention: A8 use 1.75mm filament

Attention:
Flow is proportion of filament , we suggest to use 100
Increasing flow & decrease diameter has the similar
effect.
Model surface gets many bumps when flow is too
big;model frame gets flimsy if flow is too small.

We suggest not to change

it , A8 default 0.4mm

We suggest not to change it ,

or use the date in the picture

We suggest 0.2mm to avoid initial layer tilt,0.3mm

is more easy to seperate from the platform.

Initial layer line proportion

“0” means using default speed

Min printing time for each layer. When the time is

less than 10 , it prints slower. It’s better to
decrease time when printing thin and long models.

We suggest not choose this when printing ABS.

19
Attention:Normally this option cannot be
changed , if changed ,it’s at your peril.

Attention:Normally this option cannot be

changed , if changed , it’s at your peril.

Starting
Ending

20
2.3 Expert Setting

21
 1
2
3
4

1. The minimum length before retraction . Used to avoid frequent retraction. No need to
change.
2. Enable Combing: Digital for surface quality , the nozzle will try not to go through surface ,
that’s why Cura is better than Slic3r.
3. Minimum extrusion length , to avoid frequent extrusion.
4. The height extruder rise in the retraction . If you need to set this option , 2mm is suitable .

Printing route
Printing route
without Combing
with Combing

Go through the
Go aside of the
surface
surface

22
Skirt is to avoid extruder unfilled before printing , and it appears only when platform
attachment type is None. Normally “1” is ok . Change it to “0” when your model reaches the
maximum size , or the printing size will be too big.

Peripheral line quantity: 1 Peripheral line quantity: 1

Start distance: 3 Start distance: 3

23
1. To ensure the attachment of model to platform , fan won’t start at the beginning.
2-4. Fan speed min & max : If they are not equal , the soft ware will choose a suitable speed
during them.
5. Condition to choose cool head lift : When it’s printing with the minimum speed but still cannot
reach the minimum time , you need to choose cool head lift . But it may cause filament leak.

24
 If no solid infill top , the only qualification is the surface thickness .
Please check the detail below.

No solid infill top With solid infill top

25
No solid infill bottom With solid infill bottom

Infill coverlap: 20 Infill coverlap: 40

26
 Structure types:lines Structure types:lines Structure types:grids
Infill covertap: 15 Infill covertap: 30 Infill covertap: 15
Distance X/Y: 0.7 Distance X/Y: 0.7 Distance X/Y: 0.7

These above are examples , you can set these options according to actual requirements. The
biggest progress Cura has made is the kinds of support
structure types , making it easier to seperate from the model.

27
 60° 45° 30°

It’s difficult to seperate if the distance between support and the supported place is too close;
The surface will be influenced if the distance is too far.
Different angle will generate different support , you can try the examples we provide above
which will have different effect.

28
 When choosing “Spiralize When choosing “Only follow
the outer contour” : Z axis mesh surface” : The nozzle
rises while X,Y axis moves , prints along the surface.
and only a hollow bottom
and a single layer of surface.

Attention: The software defaults not open the option above , you’d better not turnit on .

29
 Brim line amount: 10 Brim line amount: 20

Guidance to use Brim if needed: Expert → Expert Settings → Support → Support

Types → Birm.
The images above are only for reference , please set the parameter according to
actual requirement.

30
 Guidance to use Raft if needed: Expert → Expert Settings → Support → Support Types →
Raft.
The images above are only for reference , please set the parameter according to actual
requirement.

31
Load model Save the Gcode file Link to Youmagine

Model Display

Estimated Print Time

Estimated Length of Filament

Scaling

Whirling Mirroring

Left click the model and you will see the icon of “whirling, scaling, mirroring.

Left click to select model and move → move model.

Slide mouse wheel → scaling.
Right click to select model and move → whirling.
Shift + right click platform and move → move platform

32
 Green: X axis

Yellow: Y axis

Place platform

Reset Red: Z axis

Zoom to max size

Scaling ratio

Reset Modification ratio

33
 Z axis mirroring

Z axis mirroring

Z axis mirroring

Attention: The model will be converse after mirroring .

34
 Normal: Most used. Overhang: Used to see the vacant part.

X-Ray
Transparent

Layers:Used to s imulate the effect of

each layer and the path.

35
Right click model → Left click “Multiply
object” → Example: copy 4 model

5 models in total

Attention: You can try other

functions by yourself.

36