SUPPLY NETWORK ANALYZER

CVM-LC
(Ver 6.11 and higher)

INSTRUCTION MANUAL
( M98170301-03 / 03A )

 CIRCUTOR S.A.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 1

CONTENTS page
1.- DELIVERY SPOT CHECK .......................................................................................................... 2
2.- MAIN FEATURES ....................................................................................................................... 3
3.- MODELS ..................................................................................................................................... 5
4.- INSTALLATION AND START-UP............................................................................................... 5
4.1.- Installation. .................................................................................................................... 6
4.2.- CVM-LC connection terminal arrangement (power supply connection terminal)............................... 8
4.3.- Connection drawing for the CVM-LC :........................................................................... 9
5.- OPERATION MODE ................................................................................................................. 13
6.- SET-UP PROCEDURE ............................................................................................................. 15
6.1.- Phase-to-Phase or Phase-to-Neutral voltages............................................................ 16
6.2.- Voltage display mode .................................................................................................. 16
6.3.- Voltage Transformer Primary ...................................................................................... 17
6.4.- Voltage Transformer Secondary ................................................................................. 18
6.5.- Current Transformer Primary ...................................................................................... 18
6.6.- Setting power demand utility screens.......................................................................... 19
6.7.- Initial screen setting..................................................................................................... 20
6.8.- Setting of the display shutdown time ........................................................................... 20
6.9.- Clearing energy counters ............................................................................................ 21
6.10.- THD or D setting........................................................................................................ 22
7.- SPECIFICATIONS .................................................................................................................... 23
8.- SAFETY CONSIDERATIONS................................................................................................... 25
1.- M ............................................................................................................................................... 25
9.- AINTENANCE ........................................................................................................................... 25
10.- TECHNICAL SERVICE ............................................................................................................. 25
11.- APPENDIX A: Second SET-UP of the CVM-LC ...................................................................... 26
11.1.- SET-UP locking or unlocking .................................................................................... 26
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 2

1.- DELIVERY SPOT CHECK

This manual is issued to help all the CVM-LC users to install and use it in
order get the best from it. After receiving the unit, please check the following points:
(a) Does this device correspond to your order specifications?
(b) Check if any damage was done during the shipment process.
(c) Verify that it includes the correct instruction manual.

The manual you hold in your hands contains information and warnings
about the CVM-LC that the user should respect in order to guarantee
a proper operation of all the instrument functions and keep its safety
conditions.

Before powering the instrument for the first time, verify following points:

(a) Power supply: see rear part of your CVM-LC

Standard: 230 V a.c. Single-phase, Frequency: 50 ... 60 Hz

SDC Model : 24 .... 120 V d.c.

Other supply voltages, on request.

(b) Maximum measuring voltage:

Standard: 300 V a.c. phase-neutral / 520 V a.c. between phases

Other models: on request
CVM-LC - measuring 110V: 110 V a.c. phase-to-neutral /190 V a.c. phase-to-phase
CVM-LC - measuring 500V: 500 V a.c. phase-to-neutral /866 V a.c. phase-to-phase

(c) Maximum measurable current: Current transformer of In / 5 A a.c.

 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 3

2.- MAIN FEATURES

The CVM-LC power meter is a programmable measuring instrument, offering
several operation possibilities selectable in its SET-UP option. Before power
supplying the instrument, read the CONNECTIONS and SET-UP sections and
choose the most suitable operation mode for getting your desired data.

L1

L2

L3
CVM-LC

The CVM-LC is an instrument which measures, calculates and displays all the
main electrical parameters at any electrical network (balanced or not). The
measuring is true RMS value, through three a.c. voltage inputs and three a.c. current
inputs (from Current Transformers .../ 5A).
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 4

By means of an internal microprocessor it simultaneously measures:

Parameter Symbol L1 L2 L3 Average
Voltage (phase-neutral) V x x x
Voltage (phase-phase) V x x x
Current A x x x
Active power kW x x x x
Reactive power L kvarL x x x x
Reactive power C kvarL /(-C) x x x x
Power factor PF x x x x
Frequency Hz x
Power demand Pd x
kW h energy x
kvarhL energy x
kvarhC energy x
Neutral current IN x
Voltage THD % THD- V x x x
Current THD % THD- A x x x

The CVM-LC delivers the visualization of above listed parameters by means of

three 4-digit, led type, displays. Up to 3 parameters can be simultaneously read in
the screen.

---------------------------------------------------------------------------------------------
OTHER FEATURES
- Low-size (144 x 144 mm), panel-mounting analyzer.
- True R.M.S. measuring system.
- Memorizes maximum and minimum values.
- Maximum power demand calculation: kW, kVA, AIII, or current per phase
- Energy measurement (indication through a lighting led)
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 5

3.- MODELS

Code Model Current

measurement
7 70 561 CVM-LC Shunts
7 70 562 CVM-LC-ITF ITF

4.- INSTALLATION AND START-UP

The manual you hold in your hands contains information and warnings
that the user should respect in order to guarantee a proper operation
of all the instrument functions and keep its safety conditions. The
instrument must not be powered and used until its definitive assembly
on the cabinet’s door.

If the instrument is not used as manufacturer’s specifications, the

protection of the instrument can be damaged.

When any protection failure is suspected to exist (for example, it presents

external visible damages), the instrument must be immediately powered off. In this
case contact a qualified service representative.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 6

4.1.- Installation.
Before powering the instrument for the first time, verify following points:

a.- Power supply: see rear part of your CVM-LC

Standard supply : Single-phase 230 V ∼ (a.c.)
- Frequency : 50 - 60 Hz
- Supply voltage tolerance : - 10 % / + 15
- Connection terminal : Terminals 1 - 2 (Power supply)
- Burden : 5 VA

SDC Model : 0.24.... 120 V c.c. ( continua )
- Supply voltage tolerance : - 20 % / + 15
- Connection terminal : Terminals 1 - 2 (Power supply)
- Burden : 2,2 W

On request: other voltages

b.-Maximum voltage at the voltage measuring circuit:

Standard : 300 V a.c. phase-to-neutral/520 V a.c. phase-to-phase
45 to 65 Hz

Other models on request :
CVM-LC-measuring 500 V: 500 Va.c. phase-to-neutral/866 Va.c. phase-to-phase
CVM-LC-measuring 110 V: 110 Va.c. phase-to-neutral/190 Va.c. phase-to-phase
c.- Maximum allowable current : Current Transformer of In / 5 A a.c.
d.- Operation conditions :
- Operation temperature range : -10 to +50 ºC
- Humidity : 5 to 95 % R.H. non-condensing
- Altitude : below 2000 m
e.- Safety :
- Designed to meet protection class III- 300 V a.c. as (EN 61010).
- Protection against electric shock by class II double-isolation
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 7

Mounting:
Instrument is to be mounted on panel (cut-out 138+1 x 138+1 mm, as per DIN
43 700). All connections keep inside the cabinet.

Note that with the instrument powered on, the terminals could be dangerous to
touching and cover opening actions or elements removal may allow accessing
dangerous parts. Therefore, the instrument must not be used until this is completely
installed.
The instrument must be connected to a power supply circuit protected with gl
type (IEC 269 ) or M type fuses rated between 0.5 and 2 A. This circuit should be
provided with a circuit breaker or any equivalent element to connect (ON) or
disconnect (OFF) the instrument from the power supply network. The supply and
measuring voltage circuits will be both connected through a wire with a minimum
2
cross-section of 1 mm .
The line of the current transformer secondary will have a minimum cross-
section of 2,5 mm2.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 8

4.2.- CVM-LC connection terminal arrangement (power supply connection terminal)

(see lable on the rear part)

I n / 5A 300 V

CAT III
P2 P1 P2 P1 P2 P1
P-N P-P
230 V
L1 L2 L3 300V 520V
Power Supply S2 S1 S2 S1 S2 S1 N VL1 VL2 VL3
1 2 3 4 5 6 7 8 9 10 11 12

No. Terminal description No. Terminal description

1 Power supply AL1 7 IL3 S2 Current measurement
2 Power supply AL2 8 IL3 S1 Current measurement
3 IL1 S2 Current measurement 9 Neutral
4 IL1 S1 Current measurement 10 VL1 Measurement
5 IL2 S2 Current measurement 11 VL2 Measurement
6 IL2 S1 Current measurement 12 VL3 Measurement

NOTE: Terminals 3, 5, 7 are internally connected to the 9 terminal (Neutral)

... / 5 A current inputs are isolated for the ITF model.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 9

4.3.- Connection drawing for the CVM-LC :

a.- Three-phase network.- 4 wires (low voltage) :

P2 P1
L1

S2 S1 P2 P1
L2

S2 S1 P2 P1
L3

S2 S1 N

1 2 3 4 5 6 7 8 9 10 11 12

VL3
A.C. POWER SUPPLY VL2
VL1
PowerSupply (SDC Model) N
Terminal Description
1 + V d.c.
2 - V d.c.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 10

b.-Three-phase network – 3 wires (low voltage):

P2 P1
L1

S2 S1 P2 P1
L2

S2 S1 P2 P1
L3

S2 S1

1 2 3 4 5 6 7 8 9 10 11 12

VL3
A.C. POWER SUPPLY VL2
VL1
PowerSupply (SDC Model)
Terminal Description
1 + V d.c.
2 - V d.c.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 11

c.- Three-phase network - 3 wires (2 P.T. and 3 C.T.):

P2 P1
L1

S2 S1 P2 P1
L2

S2 S1 P2 P1
L3

S2 S1
A B A B

a b a b

A B

a b

1 2 3 4 5 6 7 8 9 10 11 12

VL3
VL2
VL1
A.C. POWER SUPPLY

PowerSupply (SDC Model)

Terminal Description
1 + V d.c.
2 - V d.c.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 12

d.- Three-phase network - 3 wires (2 P.T. and 2 C.T.):

P2 P1
L1

S2 S1
L2

P2 P1
L3

S2 S1
A B A B

a b a b

A B

a b

1 2 3 4 5 6 7 8 9 10 11 12

VL3
VL2

A.C. POWER SUPPLY

VL1

PowerSupply (SDC Model)

Terminal Description
1 + V d.c.
2 - V d.c.

IMPORTANT REMARK! if power = -0.01 is shown for any of the phases (codes 03,
09 and 15) and voltage and current are not zero for this phase, check out following
points:
- Assure that L1, L2 and L3 phases coincide in voltage and current.
- Correct polarity? Reverse the current transformer placed at this phase.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 13

5.- OPERATION MODE

The instrument has three displays. Each one has also a LED type indicators
(red colour). Every led will be on according to the parameter presently shown in
screen.
When the CVM-LC is powered on, 2 screens with the indication of the
program version and the hardware configuration.
After some seconds, the analyzer is ready for operation and shows one of the
available screens. A led next to the shown parameter is on.

Parameters on display can be switch by pressing the key . Leds on the

right or left indicate the parameters shown on screen at any moment.
When the first led (red) is on, it means that VOLTAGE values are shown on
screen, that is, the user can read the voltage of the phase L1 (V1), voltage of the
phase L2 (V2) and voltage of the phase L3 (V3).

Whether the key " " is press, the next led will be on, so indicating that for
this screen CURRENT values of each phase are now shown.

Pressing again the key " " , the next led will be on, and the screen will
shown following three parameters, and so successively.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 14

Max min
Pressing the "max" or "min" key, maximum or minimum values for the
parameters being shown by display, respectively, appear in screen.
This function is only valid while you keep pressing the "max" or "min" key. If
you stop pressing the key the instantaneous values will appear again after 5
seconds.
While showing maximum or minimum values the LED indicators will keep
blinking.

reset
Pressing the "reset" key the system is reset. This is equivalent to switch off
the power supply of the instrument. The maximum and minimum values recorded will
be automatically deleted from the internal memory.
If you are in the set-up process and press the "reset" key, you exit it without
saving any modification that you might have done (this event will depend on the set-
up section that is accessed when the reset action is carried out) and reset of the
system occurs.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 15

6.- SET-UP PROCEDURE

The set-up procedure of the CVM-LC is performed by means of several SET-
UP options.

For accessing the set-up menu the keys max & min must be
simultaneously pressed once the instrument is at the main screen.

When accessing the SET-UP, the message "SET-UP unlo " (1) is shown for
some seconds on screen, or, otherwise, the message "SET-UP loc" (2).
(1) Set-up UNLO (SET-UP unlocked ) : when the SET-UP is
accessed, configuration parameters can be either visualized and
modified.
(2) Set-up LOC (SET-UP locked ) : when the SET-UP is accessed,
configuration parameters can be visualized but cannot be modified .
Once into the SET-UP, use the keyboard to select different options and enter
required variables:
- The key validates de value and pass to the next menu.
- The key MAX permits to select among different options in a menu, or to
increase a digit when a variable is being entered.
- The key MIN permits to move the cursor along the digits.
Different options are following shown in a sequential mode:

1. Choice of visualization of phase-to-neutral or phase-to-phase voltages

2. Voltage display mode
3. Voltage transformation ratio.
4. Value of the current transformer primary : 1 a 10000 A
5. Power demand meter setting
6. Choice of default initial screen
7. Time for display shutdown
8. Deleting energy counters
9. Choice of harmonic distortion determination mode: d% or THD%
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 16

6.1.- Phase-to-Phase or Phase-to-Neutral voltages

After the word "set" you will see on the three displays the voltages of the
phases L1, L2, L3.

U1 U12
U2 or U23
U3 U31

- Phase to Neutral Voltages: U1, U2, U3

- Phase to Phase Voltages : U12, U23, U31
a) To select one of the voltage options just press the green key "max" and
both options will appear alternately.

b) When you get in the display the desired option just press the " " key to
validate it and access to the next set-up option.
6.2.- Voltage display mode
This option permits the user to select the voltage display mode. That way, the
choice between viewing the voltage with one decimal digit or without decimals is
user-programmable.

SEt SEt
Udec ó Udec
no YES
No decimals 1 decimal digit
c) To select one of the voltage options just press the green key "max" and
both options will appear alternately.

d) When you get in the display the desired option just press the " " key to
validate it and access to the next set-up option.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 17

6.3.- Voltage Transformer Primary

On the screen we read the word "SET U P" followed by 5 digits. They allow
us setting the primary of the voltage transformer.
SET U
P --
---
a.- To write or modify the value just repeatedly press the "max" key and the
blinking digit value will be increased.
b.- When the value on screen is the proper one, we can pass to the next digit
by pressing the "min" key in order to modify the other values.
c.- When the blinking digit is the last one, pressing the "min" key we go back
to the initial value: set values can be again modified.

d.- Press" " to pass to the next setup option.

Note: Maximum values of transformation ratios which are allowable to be set,

depend on the full-scale value of the measuring instrument. (see indications on the
rear side lable).

FULL-SCALE MAXIMUM ALLOWABLE

VALUE VALUE

110 V~ 99,999

300 V~ 70,000

500 V~ 40,000

- In case that a value higher than the maximum allowable value is validated
" ", the screen will blink and the previous set value will be kept in memory.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 18

6.4.- Voltage Transformer Secondary

We can now set the value of the secondary of the voltage transformer. Only
three digits are available:
SET U
S
---
Same process than in point ¡Error! No se encuentra el origen de la
referencia.:
- "max" key: Allows us modifying the value of the blinking digit. Each time it
is pressed the value is increased.
- "min" key: Allows us the validation of the blinking digit and going to the
next one.
- Press " " to pass to the next setup option.
If the CVM-LC is directly connected to the mains (without voltage
transformer) the values of primary and secondary must be the same, for instance
00001/001.

6.5.- Current Transformer Primary

"SET A P" and five digits appear on screen allowing us to set the primary of
the current transformer.
SET A
P --
---


1 A ... 10.000 A

a) To enter or modify the value of the C.T.'s primary, just repeatedly press "max" to
increase the value of the blinking digit.
b) When the value in screen is the required, pass to the next digit by pressing "min",
so that the whole value can be set.
c) When the last digit blinks, pressing then "min" the first digit is again accessed, so
that set value can be modified if required.

d) To access next set-up option press " ".

 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 19

NOTES:
- The secondary of the current transformers is not programmable. It is
automatically set at 5 A (... / 5 A ac)
- The primary current value to be set is also limited by the following
condition: The maximum allowable primary current value which can be set
is defined by the fact that the multiplication of the primary voltage value by
this primary current value cannot exceed 20,000,000.

6.6.- Setting power demand utility screens.

Push the key " " and the following screens will appear by display:

1.- PARAMETER TO CONTROL ("Pd Code xx")

None 00
Three phase active power kW III 16
Three phase apparent power kVA III 34
Average three-phase current AIII 36
Current per phase A1 – A2 – A3 A-PH
Value of power integrated during the programmed demand period.
2.- DEMAND PERIOD ( 1 to 60 min.) ("Pd Per xx")
3.- CLEAR MAXIMUM VALUE IN MEMORY
("CLr Pd xx") no or YES

Programming mode:
- "max" key: allows choosing the different available options.
- "min" key: allows the validation of the blinking digit and go forward to the
next digit (only for the "Pd Per xx" option).
- To pass to the next option press " ".

If you don't want to modify anything, just press the " " key three times
without modifying any value.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 20

6.7.- Initial screen setting

This option allows choice among fixed or rotary screen:

a) Fixed screen (choice is switch just pressing ): choice the initial screen to be
shown when the CVM-LC is powered (or when the CVM-LC is reset).
b) Rotary screens: all screens are successively shown at intervals of 5 s.
This option is noticed by means of some leds:
SET
dEF
PAGE
- The key "max": permits to modify the selected page. The led of the selected
option will be on. Whether rotary screens option is selected, then all leds will be
on.

- Press " " to validate the choice.

6.8.- Setting of the display shutdown time

Setting of the period of time to go by, from the moment that the CVM
keyboard is not touched anymore, before the CVM display is automatically shut
down (low consumption mode):
dISP
OFF
05 → Time to shutdown (Minutes)
When the display is shut down, a Led at the bottom left corner of the CVM will
keep blinking. The display will be automatically turned on when any CVM key is
pressed.
- "max" key: to modify the value of the blinking value.
- "min" key: to validate the blinking value and go to the next digit.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 21

6.9.- Clearing energy counters

On display we see "CLR ENER no" (Clear energy counters).
- "max": To select "YES" or "no"

-" ": To validate the choice and pass to the following set-up option.

Display:
If any of the energies is programmed (kWh, kvarhL or kvarhC), it is displayed
as follows:
kWh
max MWh
min Wh
Example : If the accumulated energy is 32.534,810 kWh, it will be displayed
as follows:

3 2 MWh
2 534 kWh
810 Wh

2534 kWh
max 32 MWh
min 810 Wh

Note : the energy counter range is limited at 999.999.999 Wh , that is, when
the value of 1 GWh is reached, the counter is reset to zero.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 22

6.10.- THD or D setting

SET SET
DHAR or dHAR
d Thd
Two modes for the harmonic distortion calculation can be selected:
a) d % : total value of the harmonic distortion referred to the fundamental value.
b) Thd % : total value of the harmonic distortion referred to the R.M.S. value.

The selected option will be the one shown on screen.

- To select any option just press "max" to switch between the two available
options.

- Press " " to validate the choice. Since all set-up options have been
completed, the set-up is exited, all modifications are saved in memory, and the
running mode automatically starts up.
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 23

7.- SPECIFICATIONS
Power supply : see specifications on the rear part of the CVM-LC
- CVM-LC : Single-phase 230 V a.c.
Voltage tolerance: +10 % / -15 %
Frequency: 50 ... 60 Hz
Burden ................................... 5 VA
- CVM-LC - SDC : Direct current 24 V ....... 120 V d.c.
Voltage tolerence: -20 % / +15 %
Burden .................................. 2.2 W

Operation temperature ......... -10 to 50 ºC

Humidity ……………………… 5 to 95 % R.H. non-condensing
Measuring Circuits :
Rated voltage .... 300 V a.c. Phase-to-Neutral / 520 V a.c. Phase-to-Phase
Frequency .................. 45 to 65 Hz
Rated current .............. In / 5 A (isolated inputs in the CVM-144-ITF... model)
Permanent overload .....1.2 In
Current input burden .....0.75 VA
Accuracy :
Voltage ...................................... 0.5 % of readout ± 2 digits
Current ...................................... 0.5 % of readout ± 2 digits
Powers ...................................... 1 % of readout ± 2 digits

Test conditions :
- Errors due to C.T. are not included and direct voltage measurement
- Temperature between + 5 ºC and + 45 ºC
- Power factor between 0.5 and 1
- Measured values between 5 % ... 100 %
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 24

Mechanical Characteristics :
- Connection : pluggable connection terminal
- Case material Self-extinguishable, V0 plastic
- Protection Assembled unit (frontal ) : IP 55
Un-assembled unit (side and rear covers) : IP 31
- Dimensions 144 x 144 mm - depth: 84 mm
- Weight 0.400 kg
- Safety .............. Category III - 300 V a.c. / 520 a.c., as per EN-61010

Protection against electric shock by class II double-isolation

Standards : IEC 664, VDE 0110, UL 94, IEC 801, IEC 348, IEC 571-1
EN 50081-1, EN 50082-1 , EN-61010-1

Dimensions :

144 78,5 5,3

144
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 25

8.- SAFETY CONSIDERATIONS

All installation specification described at the previous chapters

named INSTALLATION AND STARTUP, INSTALLATION MODES
and SPECIFICATIONS.
Note that with the instrument powered on, the terminals could be
dangerous to touching and cover opening actions or elements removal may allow
accessing dangerous parts. This instrument is factory-shipped at proper operation
condition.

9.- MAINTENANCE
The CVM-LC does not require any special maintenance. No adjustment,
maintenance or repairing action should be done over the instrument open and
powered and, should those actions are essential, high-qualified operators must
perform them.
Before any adjustment, replacement, maintenance or repairing operation is
carried out, the instrument must be disconnected from any power supply source.
When any protection failure is suspected to exist, the instrument must be
immediately put our of service. The instrument’s design allow a quick replacement in
case of any failure.

10.- TECHNICAL SERVICE

For any inquiry about the instrument performance or whether any failure
happens, contact to CIRCUTOR’s technical service.
CIRCUTOR S.A. - After-sales service
Vial Sant Jordi, s/n
08232 - Viladecavalls
Tel - + 34 93 745 29 00
fax - + 34 93 745 29 14
E-mail : [email protected]
 ----- Supply network analyzer CVM-LC ------ User's manual --- Page No. 26

11.- APPENDIX A: Second SET-UP of the CVM-LC

A second SET-UP menu is accessible in order to protect the configuration of
the CVM-LC against undesired modifications.
To access this menu proceed as follows:

- Being the CVM-LC powered off, simultaneously press " ", "max" and
"min" keys.
- Holding these keys pressed, powered the CVM-LC on.
When this option of the 2nd Setup menu is accessed, the following message
will be shown in screen during some seconds
Set
UP
Inic

11.1.- SET-UP locking or unlocking

SET
Up
Unlo

Loc (locked SET-UP) or Unloc (unlocked SET-UP)
Use the key "max" to modify the choice.

- Whether LOC is set, when the SET-UP is accessed, configuration

parameters can be visualized but cannot be modified.
- To modify the previously set option, a 4-figure password is required to be
entered (in case that this password is not correct, this blinks and the previous
menu is again accessed).

PASSWORD : 1234

To exit this set-up mode, the key RESET can be pressed at any moment
(WARNING: if the set-up is exited by pressing the key RESET some last
modifications might not be saved in memory) or reach the end of this set-up mode.