Test Report: FCC PART 15.407 Rss-Gen, Issue 5, April 2018 RSS-247, ISSUE 2, FEBRUARY 2017
Test Report: FCC PART 15.407 Rss-Gen, Issue 5, April 2018 RSS-247, ISSUE 2, FEBRUARY 2017
407
RSS-GEN, ISSUE 5, APRIL 2018
RSS-247, ISSUE 2, FEBRUARY 2017
TEST REPORT
For
Jerry Zhang
Reviewed By: EMC Manager
Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or
used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report must not be
used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal
Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*”.
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
TABLE OF CONTENTS
FCC §15.407 (f) & §1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................11
APPLICABLE STANDARD ............................................................................................................................................11
RSS-102 § 2.5.2 - EXEMPTION LIMITS FOR ROUTINE EVALUATION – RF EXPOSURE
EVALUATION ............................................................................................................................................................12
APPLICABLE STANDARD ............................................................................................................................................12
FCC §15.203& RSS-GEN CLAUSE 6.8 - ANTENNA REQUIREMENT ..............................................................13
APPLICABLE STANDARD ............................................................................................................................................13
ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................................14
FCC §15.209, §15.205 , §15.407(b) &RSS-247 §6.2, RSS-GEN§8.10 –UNWANTED EMISSION ........................15
APPLICABLE STANDARD ............................................................................................................................................15
EUT SETUP ................................................................................................................................................................17
EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................18
TEST PROCEDURE ......................................................................................................................................................19
CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................19
TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................20
TEST DATA ................................................................................................................................................................21
FCC §15.407(a)(e) & RSS-247 §6.2,RSS-Gen §6.7–EMISSION BANDWIDTH AND OCCUPIED
BANDWIDTH..............................................................................................................................................................32
APPLICABLE STANDARD ............................................................................................................................................32
TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................32
TEST PROCEDURE ......................................................................................................................................................32
TEST DATA ................................................................................................................................................................32
FCC §15.407(a) & RSS-247 §6.2 –MAXIMUM CONDUCTED OUTPUT POWER ............................................42
APPLICABLE STANDARD ............................................................................................................................................42
TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................44
TEST PROCEDURE ......................................................................................................................................................44
TEST DATA ................................................................................................................................................................45
FCC §15.407(a)& RSS-247 §6.2- POWER SPECTRAL DENSITY .......................................................................46
APPLICABLE STANDARD ............................................................................................................................................46
Page 2 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 3 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
GENERAL INFORMATION
Product Description for Equipment under Test (EUT)
Note: Both the adapter and battery have two manufacturer; Battery #1 was used in test.
Objective
This type approval report is prepared on behalf of SZ DJI TECHNOLOGY CO., LTD in accordance with
Part 2-Subpart J, Part 15-Subparts A, and E of the Federal Communications Commission’s rules. And
RSS-247, Issue 2, February 2017, RSS-Gen Issue 5, April 2018 of the Innovation, Science and Economic
Development Canada.
The tests were performed in order to determine compliance with FCC Rules Part 15, Subpart E, section
15.203, 15.205, 15.209 and 15.407 rules and RSS-247, Issue 2, February 2017, RSS-Gen Issue 5, April
2018 of the Innovation, Science and Economic Development Canada.
Related Submittal(s)/Grant(s)
FCC Part 15B JBP submissions with FCC ID: SS3-MT1SS51905.
Part of system submissions with FCC ID: SS3-MR1SS51905.
Test Methodology
All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices. And KDB 789033 D02
General U-NII Test Procedures New Rules v02r01, and RSS-247, Issue 2, February 2017, RSS-Gen Issue
5, April 2018 of the Innovation, Science and Economic Development Canada.
All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Dongguan).
Page 4 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Measurement Uncertainty
Parameter Measurement Uncertainty
Occupied Channel Bandwidth ±5 %
RF output power, conducted ±0.61dB
Power Spectral Density, conducted ±0.61 dB
30M~200MHz: 4.55 dB,200M~1GHz: 5.92 dB,1G~6GHz: 4.98 dB,
Unwanted Emissions, radiated
6G~18GHz: 5.89 dB,18G~26.5G:5.47 dB,26.5G~40G:5.63 dB
Unwanted Emissions,conducted ±1.5 dB
Temperature ±1℃
Humidity ±5%
DC and low frequency voltages ±0.4%
Duty Cycle 1%
AC Power Lines Conducted Emission 3.12 dB (150 kHz to 30 MHz)
Test Facility
The Test site used by Bay Area Compliance Laboratories Corp. (Dongguan) to collect test data is located
on the No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China.
The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the
FCC Public Access Link (PAL) database, FCC Registration No. : 897218, the FCC Designation No. :
CN1220.
The lab has been recognized by Innovation, Science and Economic Development Canada to test to
Canadian radio equipment requirements, the CAB identifier: CN0022.
Page 5 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
The device employs 5 channels for 5MHz mode and 20MHz mode, 2 channels for 40 MHz mode as
below:
5MHz/20MHz mode:
Frequency Frequency
Channel Channel
(MHz) (MHz)
1 5745 4 5805
2 5765 5 5825
3 5785 / /
40MHz mode:
Frequency Frequency
Channel Channel
(MHz) (MHz)
1 5755 2 5795
The devices have two antenna chains can transmission, but only supports SISO mode.
Page 6 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
5 MHz Mode
RBW 10 MHz
* VBW 10 MHz
Ref 41 dBm * Att 25 dB SWT 100 ms
40 Offset 11 dB
A
30 SGL
1 PK *
CLRWR
20 LVL
10
-10
3DB
-20
-30
-40
-50
20 MHz Mode
RBW 10 MHz
* VBW 10 MHz
Ref 41 dBm * Att 25 dB SWT 100 ms
40 Offset 11 dB
A
30 SGL
1 PK *
CLRWR
20 LVL
10
-10
3DB
-20
-30
-40
-50
Page 7 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
40 MHz Mode
RBW 10 MHz
* VBW 10 MHz
Ref 41 dBm * Att 25 dB SWT 100 ms
40 Offset 11 dB
A
30 SGL
1 PK *
CLRWR
20 LVL
10
-10
3DB
-20
-30
-40
-50
Equipment Modifications
No modification was made to the EUT.
Page 8 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
1.0 Meter
EUT
SD Card
Non-Conductive Table
80/150 cm above Ground
Plane
1.5 Meter
Page 9 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Note:
Not Aplicable*: The EUT was powered by battery.
Page 10 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Calculation formula:
Calculated Data:
Conducted
output power Evaluation Power MPE
Frequency Antenna Gain
including Tune- Distance Density Limit
(MHz)
up Tolerance (cm) (mW/cm2) (mW/cm2)
(dBi) (numeric) (dBm) (mW)
5745-5825 4 2.51 24 251 20.00 0.13 1.0
Note 1: the Max. Target Power including Tolerance was declared by manufacturer.
Result: Compliance, The device meets MPE requirement for Devices Used by the General Public
(Uncontrolled Environment) at distance ≥20 cm.
Page 11 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
RF exposure evaluation is required if the separation distance between the user and/or bystander and the
device’s radiating element is greater than 20 cm, except when the device operates as follows:
• below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less
than 1 W (adjusted for tune-up tolerance);
• at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the
device is equal to or less than 4.49/ƒ0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz;
• at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the
device is equal to or less than 0.6 W (adjusted for tune-up tolerance);
• at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the
device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz;
• at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or
less than 5 W (adjusted for tune-up tolerance).
In these cases, the information contained in the RF exposure technical brief may be limited to information
that demonstrates how the e.i.r.p. was derived.
Calculated Data:
The maximum power including tune-up tolerance is 24dBm@ 5.8 GHz band, the maximum antenna gain
is 4.0 dBi, so the maximum e.r.i.p. is 28 dBm (0.631W)
So the device is compliance exemption from Routine Evaluation Limits –RF exposure Evaluation.
Result: Compliance
Page 12 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
According to RSS-Gen §6.8, The applicant for equipment certification shall provide a list of all antenna
types that may be used with the transmitter, where applicable (i.e. for transmitters with detachable
antenna), indicating the maximum permissible antenna gain (in dBi) and the required impedance for each
antenna. The test report shall demonstrate the compliance of the transmitter with the limit for maximum
equivalent isotropically radiated power (e.i.r.p.) specified in the applicable RSS, when the transmitter is
equipped with any antenna type, selected from this list.
For expediting the testing, measurements may be performed using only the antenna with highest gain of
each combination of transmitter and antenna type, with the transmitter output power set at the maximum
level. However, the transmitter shall comply with the applicable requirements under all operational
conditions and when in combination with any type of antenna from the list provided in the test report
(and in the notice to be included in the user manual, provided below).
When measurements at the antenna port are used to determine the RF output power, the effective gain of
the device’s antenna shall be stated, based on a measurement or on data from the antenna’s manufacturer.
The test report shall state the RF power, output power setting and spurious emission measurements with
each antenna type that is used with the transmitter being tested.
For licence-exempt equipment with detachable antennas, the user manual shall also contain the following
notice in a conspicuous location:
This radio transmitter [enter the device’s ISED certification number] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types listed below, with the
maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than
the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Immediately following the above notice, the manufacturer shall provide a list of all antenna types which
can be used with the transmitter, indicating the maximum permissible antenna gain (in dBi) and the
required impedance for each antenna type.
Page 13 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Result: Compliance.
Page 14 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
(b) Undesirable emission limits. Except as shown in paragraph (b)(7) of this section, the maximum
emissions outside of the frequency bands of operation shall be attenuated in accordance with the
following limits:
(1) For transmitters operating in the 5.15-5.25 GHz band: All emissions outside of the 5.15-5.35
GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz.
(2) For transmitters operating in the 5.25-5.35 GHz band: All emissions outside of the 5.15-5.35
GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz.
(3) For transmitters operating in the 5.47-5.725 GHz band: All emissions outside of the 5.47-5.725
GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz.
(i) All emissions shall be limited to a level of −27 dBm/MHz at 75 MHz or more above or below the
band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25
MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or
below the band edge, and from 5 MHz above or below the band edge increasing linearly to a level of 27
dBm/MHz at the band edge.
(ii) Devices certified before March 2, 2017 with antenna gain greater than 10 dBi may demonstrate
compliance with the emission limits in §15.247(d), but manufacturing, marketing and importing of
devices certified under this alternative must cease by March 2, 2018. Devices certified before March 2,
2018 with antenna gain of 10 dBi or less may demonstrate compliance with the emission limits in
§15.247(d), but manufacturing, marketing and importing of devices certified under this alternative must
cease before March 2, 2020.
(5) The emission measurements shall be performed using a minimum resolution bandwidth of 1
MHz. A lower resolution bandwidth may be employed near the band edge, when necessary, provided the
measured energy is integrated to show the total power over 1 MHz.
(6) Unwanted emissions below 1 GHz must comply with the general field strength limits set forth
in §15.209. Further, any U-NII devices using an AC power line are required to comply also with the
conducted limits set forth in §15.207.
(7) The provisions of §15.205 apply to intentional radiators operating under this section.
Page 15 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
According to RSS-247§6.2
Page 16 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
EUT Setup
Below 1 GHz:
Page 17 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
1-26.5 GHz:
26.5-40 GHz:
The radiated emission Below 1GHz tests were performed in the 10 meters chamber test site, above 1GHz
tests were performed in the 3 meters chamber test site A, using the setup accordance with the ANSI
C63.10-2013. The specification used was the FCC 15.209, and FCC 15.407 and RSS-247, RSS-Gen
limits.
The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the
middle.
During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the
following configurations:
Page 18 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
30-1000MHz:
1GHz- 40GHz:
If the maximized peak measured value complies with under the QP/Average limit more than 6dB, then it
is unnecessary to perform an QP/Average measurement.
Test Procedure
During the radiated emission test, the adapter was connected to the first AC floor outlet.
Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-1GHz, peak and
Average detection modes for frequencies above 1GHz.
According to KDB 789033 D02 General UNII Test Procedures New Rules v02r01, emission shall be
computed as: E [dBμV/m] = EIRP[dBm] + 95.2, for d = 3 meters.
According to C63.10, the above 1G test result shall be extrapolated to the specified distance using an
extrapolation factor of 20dB/decade from 3m to 1.5m or 1m
Distance extrapolation factor =20 log (specific distance [3m]/test distance [1.5m]) dB= 6.02 dB
or
Distance extrapolation factor =20 log (specific distance [3m]/test distance [1m]) dB= 9.54 dB
All emissions under the average limit and under the noise floor have not recorded in the report.
Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain
The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin
calculation is as follows:
Page 19 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
For the range 1GHz-40GHz, Test performed at 1.5m or 1m, the Corrected Amplitude is calculated by
adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading
and the Distance extrapolation factor. The basic equation is as follows:
Corrected Amplitude
= Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain-Distance extrapolation factor
The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin
calculation is as follows:
* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations
have been performed, traceable to National Primary Standards and International System of Units (SI).
Page 20 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Test Data
Environmental Conditions
Temperature: 22.6~24C
Relative Humidity: 51~55 %
ATM Pressure: 100.1kPa
* The testing was performed by Tyler Pan and Neil Liao on 2019-06-05.
Horizontal
Page 21 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Vertical
Page 22 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
2) 1GHz-40GHz:
Chain 0, 5MHz mode:
Receiver Rx Antenna Cable Amplifier Corrected Extrapolation
Frequency Limit Margin
Reading Polar Factor loss Gain Amplitude result
(MHz) Detector (dBμV/m) (dB)
(dBμV) (H/V) (dB/m) (dB) (dB) (dBμV/m) (dBμV/m)
Page 23 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 24 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 25 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 26 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 27 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 28 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Fundamental
Test with Band
Rejection Filter
Page 29 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Vertical
Fundamental
Test with Band
Rejection Filter
Page 30 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Page 31 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Calibration Calibration
Manufacturer Description Model Serial Number
Date Due Date
* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations
have been performed, traceable to National Primary Standards and International System of Units (SI).
Test Procedure
According to KDB 789033 D02 General UNII Test Procedures New Rules v02r01
Test Data
Environmental Conditions
Temperature: 25.1C
Relative Humidity: 68 %
ATM Pressure: 101.4 kPa
Page 32 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
99%
6dB 6dB
Frequency Occupied
Mode Channel Bandwidth Bandwidth
(MHz) Bandwidth
(MHz) Limit (MHz)
(MHz)
Low 5745 4.180 0.5 6.020
5 MHz Middle 5785 4.180 0.5 5.740
High 5825 4.200 0.5 5.340
Low 5745 15.952 0.5 22.000
20 MHz Middle 5785 15.551 0.5 22.960
High 5825 15.952 0.5 18.960
Low 5755 35.110 0.5 36.960
40 MHz
High 5795 35.271 0.5 36.960
Note: the 99% Occupied Bandwidth have not fall into the band 5470-5725MHz, please refer to the test plots of 99%
Occupied Bandwidth.
Page 33 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
6dB Bandwidth:
5 MHz mode, Low Channel
* RBW 100 kHz Delta 1 [T1 ]
* VBW 300 kHz 1.34 dB
Ref 36 dBm * Att 20 dB SWT 20 ms 4.180000000 MHz
1 PK 20
MAXH
D1 15.9 dBm
LVL
1
1
10 D2 9.9 dBm
-10
-20 3DB
-30
-40
-50
-60
1 PK 20
MAXH
D1 15.3 dBm LVL
1 1
10 D2 9.3 dBm
-10
-20 3DB
-30
-40
-50
-60
Page 34 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
1 PK 20
MAXH
D1 14.5 dBm LVL
1
10 1
D2 8.5 dBm
-10
-20 3DB
-30
-40
-50
-60
1 PK
MAXH D1 11.66 dBm
10 1 1 LVL
D2 5.66 dBm
-10
-20
3DB
-30
-40
-50
-60
-70
Page 35 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
1 PK
MAXH
D1 12.47 dBm
10 1 1 LVL
D2 6.47 dBm
-10
-20
3DB
-30
-40
-50
-60
-70
1 PK
MAXH D1 10.58 dBm
10
1 1 LVL
D2 4.58 dBm
-10
-20
3DB
-30
-40
-50
-60
-70
Page 36 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
1 PK
MAXH
10
LVL
0
D1 -1.99 dBm
1 1
D2 -7.99 dBm
-10
-20
3DB
-30
-40
-50
-60
-70
1 PK
MAXH
10
LVL
0 D1 -0.77 dBm
1 1
D2 -6.77 dBm
-10
-20
3DB
-30
-40
-50
-60
-70
Page 37 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
10
0 T1 T2
-10
3DB
-20
-30
-40
-50
10
0 T1 T2
-10
3DB
-20
-30
-40
-50
Page 38 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
10
0 T1 T2
-10
3DB
-20
-30
-40
-50
0 T1 T2
-10
-20
3DB
-30
-40
-50
-60
-70
Page 39 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
0 T1 T2
-10
-20
3DB
-30
-40
-50
-60
-70
0 T1
T2
-10
-20
3DB
-30
-40
-50
-60
-70
Page 40 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
0
T1 T2
-10
-20
3DB
-30
-40
-50
-60
-70
0 T1 T2
-10
-20
3DB
-30
-40
-50
-60
-70
Page 41 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
(i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted
output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna
gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in
any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the
maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any
elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm).
(ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output
power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain
does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any
1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the
maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi.
(iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum
conducted output power over the frequency band of operation shall not exceed 1 W. Fixed point-to-point
U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding
reduction in the maximum conducted output power or maximum power spectral density. For fixed point-
to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in
maximum conducted output power and maximum power spectral density is required for each 1 dB of
antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint
systems, omnidirectional applications, and multiple collocated transmitters transmitting the same
information. The operator of the U-NII device, or if the equipment is professionally installed, the installer,
is responsible for ensuring that systems employing high gain directional antennas are used exclusively for
fixed, point-to-point operations.
(iv) For mobile and portable client devices in the 5.15-5.25 GHz band, the maximum conducted
output power over the frequency band of operation shall not exceed 250 mW provided the maximum
antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11
dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used,
both the maximum conducted output power and the maximum power spectral density shall be reduced by
the amount in dB that the directional gain of the antenna exceeds 6 dBi.
(2) For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over
the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm 10 log B, where B is
the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not
exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi
are used, both the maximum conducted output power and the maximum power spectral density shall be
reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi.
Page 42 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
(3) For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of
operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30
dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both
the maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII
devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi
without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations
exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated
transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is
professionally installed, the installer, is responsible for ensuring that systems employing high gain
directional antennas are used exclusively for fixed, point-to-point operations.
(4) The maximum conducted output power must be measured over any interval of continuous
transmission using instrumentation calibrated in terms of an rms-equivalent voltage.
Page 43 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations
have been performed, traceable to National Primary Standards and International System of Units (SI).
Test Procedure
According to KDB 789033 D02 General UNII Test Procedures New Rules v02r01
Page 44 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Test Data
Environmental Conditions
Temperature: 24.6C
Relative Humidity: 68 %
ATM Pressure: 100.5 kPa
Note: The antenna gain is 4dBi, meet the RSS-247 EIPR requirement.
Page 45 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
(i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted
output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna
gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in
any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the
maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any
elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm).
(ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output
power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain
does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any
1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the
maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi.
(iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum
conducted output power over the frequency band of operation shall not exceed 1 W. Fixed point-to-point
U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding
reduction in the maximum conducted output power or maximum power spectral density. For fixed point-
to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in
maximum conducted output power and maximum power spectral density is required for each 1 dB of
antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint
systems, omnidirectional applications, and multiple collocated transmitters transmitting the same
information. The operator of the U-NII device, or if the equipment is professionally installed, the installer,
is responsible for ensuring that systems employing high gain directional antennas are used exclusively for
fixed, point-to-point operations.
(iv) For mobile and portable client devices in the 5.15-5.25 GHz band, the maximum conducted
output power over the frequency band of operation shall not exceed 250 mW provided the maximum
antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11
dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used,
both the maximum conducted output power and the maximum power spectral density shall be reduced by
the amount in dB that the directional gain of the antenna exceeds 6 dBi.
(2) For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over
the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm 10 log B, where B is
the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not
exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi
are used, both the maximum conducted output
Page 46 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
power and the maximum power spectral density shall be reduced by the amount in dB that the directional
gain of the antenna exceeds 6 dBi.
(3) For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of
operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30
dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both
the maximum conducted output power and the maximum power spectral density shall be reduced by the
amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII
devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi
without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations
exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated
transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is
professionally installed, the installer, is responsible for ensuring that systems employing high gain
directional antennas are used exclusively for fixed, point-to-point operations.
Page 47 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Test Procedure
According to KDB 789033 D02 General UNII Test Procedures New Rules v02r01
* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations
have been performed, traceable to National Primary Standards and International System of Units (SI).
Page 48 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
Test Data
Environmental Conditions
Temperature: 24.4~26.6C
Relative Humidity: 62~68 %
ATM Pressure: 100.5~100.6 kPa
Maximum Power
Reading
Test Spectral Density
(dBm/300kHz) Limit
Mode Frequency (dBm/500kHz)
(dBm/500kHz)
(MHz) Chain
0 Chain 1 Chain 0 Chain 1
5745 13.26 12.72 15.46 14.92
5 MHz 5785 12.75 12.48 14.95 14.68
5825 12.11 11.37 14.31 13.57
5745 8.17 8.28 10.37 10.48
30
20 MHz 5785 8.77 9.03 10.97 11.23
5825 7.57 7.29 9.77 9.49
5755 -4.80 -3.92 -2.60 -1.72
40 MHz
5795 -3.46 -4.31 -1.26 -2.11
Note: For 5.8GHz band, If measurement bandwidth of Maximum PSD is specified in 500 kHz, add
10log(500kHz/RBW) to the measured result, whereas RBW (< 500 KHz) is the reduced resolution bandwidth of the
spectrum analyzer set during measurement.
Page 49 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
Page 50 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
Page 51 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
Page 52 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
30 Offset 11 dB
A
20
1 RM *
MAXH
10
LVL
0
1
-10
-20
3DB
-30
-40
-50
-60
-70
30 Offset 11 dB
A
20
1 RM *
MAXH
10
LVL
0 1
-10
-20
3DB
-30
-40
-50
-60
-70
Page 53 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
Page 54 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
40 Offset 11 dB
A
30
1 RM *
MAXH
20 LVL
1
10
-10
3DB
-20
-30
-40
-50
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
Page 55 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
30 Offset 11 dB
A
20
1 RM *
MAXH 1
10
LVL
-10
-20
3DB
-30
-40
-50
-60
-70
Page 56 of 57
Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG190526002-00B
30 Offset 11 dB
A
20
1 RM *
MAXH
10
LVL
0 1
-10
-20
3DB
-30
-40
-50
-60
-70
30 Offset 11 dB
A
20
1 RM *
MAXH
10
LVL
0 1
-10
-20
3DB
-30
-40
-50
-60
-70
Page 57 of 57