Scribd
Upload
64 views

Loadings - NSCP 2015

The document discusses the design of a two-story reinforced concrete residential structure using STAAD and STAAD Advanced Concrete Designer. The objectives are to calculate wind loads, design the roof truss and purlins, determine dead and live loads, input seismic parameters, and design the concrete elements. Load cases are defined based on dead, live, and earthquake loads. Seismic parameters are calculated based on the structure's location in Bulacan, Philippines and UBC 1997 standards. Reinforced concrete sections, material properties, and load values are also provided.

Uploaded by

Gabs De Guzman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
64 views

Loadings - NSCP 2015

The document discusses the design of a two-story reinforced concrete residential structure using STAAD and STAAD Advanced Concrete Designer. The objectives are to calculate wind loads, design the roof truss and purlins, determine dead and live loads, input seismic parameters, and design the concrete elements. Load cases are defined based on dead, live, and earthquake loads. Seismic parameters are calculated based on the structure's location in Bulacan, Philippines and UBC 1997 standards. Reinforced concrete sections, material properties, and load values are also provided.

Uploaded by

Gabs De Guzman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 29

DESIGN OF

TWO-STOREY REINFORCED-CONCRETE RESIDENTIAL STRUCTURE U


STAAD.Pro & STAAD Advanced Concrete Designer RC

Main objectives
1) Calculate Wind Pressure for Components and Cladding per NSCP 20
2) Design the Roof Truss and Purlins per NSCP 2015/AISC 360-10 by LR
3) Derive dead load and live load values per NSCP 2015
4) Discuss NSCP 2015/UBC 97 Seismic parameters input to STAAD
5) Design the concrete elements in STAAD Advanced Concrete Designe
(beams, slabs, columns and footings)
SIDENTIAL STRUCTURE USING
Concrete Designer RCDC

and Cladding per NSCP 2015/ASCE 7-10


P 2015/AISC 360-10 by LRFD Method

eters input to STAAD


dvanced Concrete Designer RCDC
Seismic Source Type A
LEGARDA, BAGUIO CITY
Bulacan
Bulacan
Bulacan = 250 kph
Bulacan = 250 kph
STORIES (LEVELS)
Levels Storey Height (m)

GF to 2F 4.5
2F - 3F 3
3F-ROOF 3
10.5

PROPERTIES
Beams Columns Slabs fc' fy
B-1 300x450 RC300X300 S110 20.68 Mpa 275 Mpa
B-2 250x400 S100 20.68 Mpa 276 Mpa
RB-1 250x350 20.68 Mpa 277 Mpa

LOADS
Dead Load
1) Selfweight
Concrete unit weight = 24 kN/m3

2) Member Load
150mm CHB 3.11 kN/m per meter height
100mm CHB 2.98 kN/m per meter height

Floor Load Floors


100mm slab 2.40 kN/m2
Floor finish 1.10 kN/m2
Ceiling 0.10 kN/m2
MEP 0.10 kN/m2
Interior Partition 0.00 kN/m2
Water proofing - kN/m2
1.30

Live Load
1.9 kN/m2

Seismic Parameters
UBC 97 / NSCP 2015
Zone = 4
Seismic Source Type = A
Importance Factor ( I ) = 1.0 (Standard Occupancy)
R = 8.5 - Special Moment Frame
Structure is located 40km from seismic source
Ct = 0.0731
2.63 0.24 0.24 3.11
2.5 0.24 0.24 2.98
UBC 1997

PARAMETERS T = Ct (hn)0.75 sec UBC Eq. (30-8)


Z 0.4 = 0.341 sec
I 1 < 0.70 sec therefore Ft = 0;
Rwx 8.5
Rwz 8.5
Na 1
Nv 1 V= CvIW KN UBC Eq. (30-4)
S 4 RT
Ct 0.0731 = 386.90 KN
hn 7.8
W 1753.2
Cv 0.64
Ca 0.44

Total design base shear need not exceed:


V = 2.5Ca IW KN UBC Eq. (30-5)
R
= 226.88 KN DESIGN BASE SHEAR IS TOO LARGE!
USE THIS VALUE!

Design base shear shall not be less than:


V = 0.11CaIW KN UBC Eq. (30-6)
= 84.85 KN OK!

V = 0.8ZNvIW KN UBC Eq. (30-7)


R
= 66.00 KN OK!

If Ft≠ 0:
Ft = 0.07TV UBC Eq. (30-14)
= 9.24 KN
< 0.25V = 96.73

ENGR JOHN PAUL DELA ROSA (CE)


LICENSE # 98600_PRC MANILA
0.004202
1.2 DL + 1.00 E + 0.5 LL

1 1.400 D
1 1.200 D + 1.600 Lp
1 1.420 D + 0.500 Lp + 1.250 E1
1 1.420 D + 0.500 Lp + 1.250 E2
1 1.420 D + 0.500 Lp - 1.250 E1
1 1.420 D + 0.500 Lp - 1.250 E2
1 1.420 D + 1.250 E1
1 1.420 D + 1.250 E2
1 1.420 D - 1.250 E1
1 1.420 D - 1.250 E2
1 0.680 D + 1.250 E1
1 0.680 D + 1.250 E2
1 0.680 D - 1.250 E1
1 0.680 D - 1.250 E2
E = ρ Eh + Ev
1.25

= 1.25 Eh

Ev = 0.5 Ca I DL
0.5 0.44 1 DL
= DL

= 0.22 DL

You might also like