05.

Detailed Specification
 Construction of Obstacle Courses for training of SDRF personnel under SDRF Phase-2 at SDRF Campus, Jollygrant, Dehradun

CIVIL WORKS - SPECIFICATIONS FOR SCHEDULE ITEMS / NON SCHEDULE ITEMS

BOQ Item
S.No. Description of BOQ Item Indicative Figure/Image SI/ NSI CPWD/PWD/Other/MR Ref. Code Ref. Drawing No.
No.
Earth work in excavation by mechanical means (Hydraulic
excavator) / manual means in foundation trenches or drains (not
As per latest CPWD
exceeding 1.5 m in width or 10 sqm on plan), including dressing
specifications with
1 2.8.1 of sides and ramming of bottoms, lift upto 1.5 m, including SI 2.8.1
amendment and relevant
getting out the disposal of surplus excavated soil as directed,
IS Code
within a lead of 50 m.excavated soil All kinds of soil.

Excavating, supplying and filling of local earth (including

As per latest CPWD
royalty) by mechanical transport upto a lead of 5km also
specifications with
2 2.25a including ramming and watering of the earth in layers not SI 2.25a M&A-SDRF-PH-II-
amendment and relevant
exceeding 20cm in renches, plinth, sides of foundation etc. OC-AR-6003 to
IS Code
complete. 6024
Supplying and filling in plinth with sand under floors, including As per latest CPWD
3 2.27 watering, ramming, consolidating and dressing complete. SI specifications with 2.27
amendment and relevant
Providing and laying in position cement concrete of specified IS Code
grade excluding the cost of centering and shuttering - All work As per latest CPWD
up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) specifications with
5 4.1.3 SI 4.1.3
derived from natural sources : 4 graded stone aggregate 20 mm amendment and relevant
nominal size derived from natural sources) IS Code

Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work As per latest CPWD
up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) specifications with
4 4.1.5 SI 4.1.5
derived from natural sources : 6 graded stone aggregate 20 mm amendment and relevant
nominal size derived from natural sources) IS Code

Centering and shuttering including strutting, propping etc. and As per latest CPWD
removal of form work for : Foundations, footings, bases for specifications with
9 4.3.1 SI 4.3.1
columns amendment and relevant
IS Code
Centering and shuttering including strutting, propping etc. and
As per latest CPWD
removal of form work for : Retaining walls, return walls, walls
specifications with
10 4.3.2 (any thickness) including attached pilasters, buttresses, plinth SI 4.3.2
amendment and relevant
and string courses fillets, kerbs and steps etc.
IS Code
 BOQ Item
S.No. Description of BOQ Item Indicative Figure/Image SI/ NSI CPWD/PWD/Other/MR Ref. Code Ref. Drawing No.
No.
Centering and shuttering including strutting, propping etc. and As per latest CPWD
11 5.9.1 removal of form for : Foundations, footings, bases of SI specifications with 5.9.1
columns, etc. for mass concrete amendment and relevant
Centering and shuttering including strutting,propping etc. and As perISlatest
CodeCPWD
removal of form for : Walls (any thickness) including attached specifications with
12 5.9.2 SI 5.9.2
pilasters, utteresses,plinth and string courses etc. amendment and relevant
IS Code
Centering and shuttering including strutting, propping etc. and As per latest CPWD
12 5.9.3 removal of form for : Suspended floors, roofs, landings, SI specifications with 5.9.3
balconies and access platform amendment and relevant
Centering and shuttering including strutting, propping etc. and As perISlatest
CodeCPWD
12 5.9.6 removal of form for : Columns, Pillars, Piers, Abutments, Posts SI specifications with 5.9.6
and Struts amendment and relevant
Steel reinforcement for R.C.C. work including straightening, IS Code
As per latest CPWD
cutting, bending, placing in position and binding all complete specifications with
13 5.22.6 Upto plinth level. Thermo-Mechanically Treated bars of SI 5.22.6
amendment and relevant
grade Fe-500D IS Code
Steel reinforcement for R.C.C. work including straightening, As per latest CPWD
cutting, bending, placing in position and binding all complete specifications with
14 5.22A.6 SI 5.22A.6
above plinth level. Thermo-Mechanically Treated bars of amendment and relevant
grade Fe-500D IS Code
Providing and laying in position ready mixed or site batched
design mix cement concrete for reinforced cement concrete
work; using coarse aggregate and fine aggregate derived from
natural sources, Portland Pozzolana / Ordinary Portland
/Portland Slag cement, admixtures in recommended proportions
as per IS: 9103 to accelerate / retard setting of concrete, to
improve durability and workability without impairing strength;
including pumping of concrete to site of laying, curing, carriage
for all leads; but excluding the cost of centering, shuttering, As per latest CPWD
finishing and reinforcement as per direction of the engineer-in- specifications with 5.33.1 &
15 5.33.1.2 charge; for the following grades of concrete. Note: Extra cement SI
amendment and relevant 5.33.1.2
up to 10% of the minimum specified cement content in design IS Code
mix shall be payable separately. In case the cement content in
design mix is more than 110% of the specified minimum cement
content, the contractor shall have discretion to either re-design
the mix or bear the cost of extra cement. - Concrete of M30
grade with minimum cement content of 350 kg /cum - upto
plinth level
 BOQ Item
S.No. Description of BOQ Item Indicative Figure/Image SI/ NSI CPWD/PWD/Other/MR Ref. Code Ref. Drawing No.
No.
Providing and laying in position ready mixed or site batched
design mix cement concrete for reinforced cement concrete
work; using coarse aggregate and fine aggregate derived from
natural sources, Portland Pozzolana / Ordinary Portland
/Portland Slag cement, admixtures in recommended proportions
as per IS: 9103 to accelerate / retard setting of concrete, to
improve durability and workability without impairing strength;
including pumping of concrete to site of laying, curing, carriage
for all leads; but excluding the cost of centering, shuttering,
As per latest CPWD
finishing and reinforcement as per direction of the engineer-in-
charge; for the following grades of concrete. Note: Extra cement specifications with 5.33.2 &
15 5.33.2.2 SI
up to 10% of the minimum specified cement content in design amendment and relevant 5.33.2.2
mix shall be payable separately. In case the cement content in IS Code
design mix is more than 110% of the specified minimum cement
content, the contractor shall have discretion to either re-design
the mix or bear the cost of extra cement. - Concrete of M30
grade with minimum cement content of 350 kg /cum - All
works above plinth level upto floor V level

Brick work with common burnt clay F.P.S. (non modular) bricks
As per latest CPWD
of class designation 7.5 in foundation and plinth in: Cement
specifications with
15 6.1.2 mortar 1:6 (1 cement : 6 coarse sand) SI 6.1.2
amendment and relevant
IS Code
Brick work with common burnt clay F.P.S. (non modular) bricks As per latest CPWD
of class designation 7.5 in superstructure above plinth level up specifications with
16 6.4.2 to floor V level in all shapes and sizes in : Cement mortar 1:6 SI 6.4.2
amendment and relevant
(1 cement : 6 coarse sand) IS Code
Structural steel work in single section, fixed with or without As per latest CPWD
connecting plate,including cutting, hoisting, fixing in specifications with
17 10.1 SI 10.1
position and applying a priming coat of approved steel primer amendment and relevant
all complete. IS Code
Structural steel work riveted, bolted or welded in built up As per latest CPWD
sections, trusses and framed work, including cutting, hoisting, specifications with
17 10.2 SI 10.2
fixing in position and applying a priming coat of approved steel amendment and relevant
primer all complete. IS Code
Providing and fixing hand rail of approved size by welding etc. As per latest CPWD
to steel ladder railing, balcony railing, staircase railing and specifications with
18 10.26.3 similar works, including applying priming coat of approved steel SI 10.26.3
amendment and relevant
primer. G I Pipe IS Code
 BOQ Item
S.No. Description of BOQ Item Indicative Figure/Image SI/ NSI CPWD/PWD/Other/MR Ref. Code Ref. Drawing No.
No.
13.1.1 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) As per latest CPWD
specifications with
19 SI 13.1.1
amendment and relevant
IS Code
Finishing with Epoxy paint (two or more coats) at all As per latest CPWD
locations prepared and applied as per manufacturer's specifications with
23 13.52.2 SI 13.52.2
specifications including appropriate priming coat, preparation amendment and relevant
of surface, etc. complete : On concrete work IS Code
13.60.1 Wall painting with acrylic emulsion paint of approved brand As per latest CPWD
and manufacture to give an even shade : Two or more coats on specifications with
20 SI 13.60.1
new work amendment and relevant
IS Code
Painting with synthetic enamel paint of approved brand and As per latest CPWD
manufacture to give an even shade :Two or more coats on specifications with
21 13.61.1 SI 13.61.1
new work amendment and relevant
IS Code
Providing and laying Non Pressure NP-4 class (Heavy duty)
As per latest CPWD
R.C.C. pipes including collars/spigot jointed with stiff mixture of
specifications with
22 19.36.3 cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) SI 19.36.3
amendment and relevant
including testing of joints etc. complete : 900 mm dia RCC pipes.
IS Code
Providing, making and fixing in position of First Class Teak wood
As per latest CPWD
as per drawings. Cost includes, Matrerial, conveyance, erection
Derived from specifications with
24 in position, all necessary fixing accessories, machinery etc as SI 9.1.1
DSR 9.1.1 amendment and relevant
per instruction of engineers in charge.
IS Code
Supplying, laying and tying G.I barbed wire including cost of As per latest CPWD
Derived from material, fixing accessories, labours, transportation etc. specifications with
25 SI 16.18.1
DSR 16.18.1 compltete as per drawings and instruction of engineers incharge amendment and relevant
IS Code
Supplying and erecting the 50mm dia manila rope as per
28 Non DSR drawings including cost of rope, transportation, tying and NSI As per Market Analysis
knotting etc. as per direction of engineers in charge .
Supplying installing and tying the Tyre wall of size 6m x8m and
spider web net of size 6mx9m using G.I Pipes of 100mm dia /
80mm dia, Garware PP Rope net,Colourful Used Tyre ,Static
29 Non DSR NSI As per Market Analysis
Rope etc as per drawings including cost of rope, transportation,
making spider web / tyre wall, tying and knotting etc. as per
direction of engineers in charge .
 BOQ Item
S.No. Description of BOQ Item Indicative Figure/Image SI/ NSI CPWD/PWD/Other/MR Ref. Code Ref. Drawing No.
No.
Supplying, installing and tying the Burma bridge of 15m length,
width of 0.75m and overall length of 23m using G.I Pipes of
50mm dia / 32mm dia / 25mm dia as per drawings including
30 Non DSR NSI As per Market Analysis
rope, Static Rope, juth rope etc, transportation, making bridge ,
tying and knotting etc. as per direction of engineers in charge .