Scribd
Upload
203 views

ACONIS Maintenance

This document provides instructions for recovering an ACONIS server using Norton Ghost recovery software. It describes preparing for recovery by booting from the recovery CD and agreeing to the license. The recovery process is outlined in steps, replacing the first CD with the second halfway through. After recovery is complete, the server must be rebooted and have its network settings and computer name configured before the LAN cables are reconnect and the server restarted.

Uploaded by

Fede Ronchi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
203 views

ACONIS Maintenance

This document provides instructions for recovering an ACONIS server using Norton Ghost recovery software. It describes preparing for recovery by booting from the recovery CD and agreeing to the license. The recovery process is outlined in steps, replacing the first CD with the second halfway through. After recovery is complete, the server must be rebooted and have its network settings and computer name configured before the LAN cables are reconnect and the server restarted.

Uploaded by

Fede Ronchi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Maintenance Guide

Maintenance Guide
Introduction

CHAPTER 1: Introduction
Introduction

1. Who Should Use This Document

This Document is intended for those interested in the overall


ACONIS functional capabilities, those interested in the ACONIS
interconnection with other systems, and those interested in the
ACONIS configuration.

This includes the following personnel:

1. Hardware Engineers

2. Software Developers

3. Database Maintenance Technicians

4. Console Operators
Introduction

CHAPTER 2: Recovery Software


Recovery Software

1. General Description

　This Chapter explains how to recover your ACONIS server.


　It’s made by detailed procedure based on step-by-step Installation.
　Make sure to back up important data, before Recovering ACONIS server.
Recovery process will initialize your server, therefore you may lose all data.
　Now, follow each step, and you can complete recovering your server without any
mistake.
　Norton Ghost is used for recovering your Aconis server.
　Symantec and Norton Ghost are registered trademarks of Symantec Co.

2. Preparation

　STEP.1
- Insert ACONIS2000 Recovery CD #1 into CD-ROM.
- Reboot your OWS.
- OWS will boot on Recovery CD with the following message.
- If you are asked to boot on CD, then press any key.
Recovery Software

　STEP.2
- If successfully boot on CD, you’ll see the same screen as below.
- Press “Enter” key to select choice 1.

　STEP.3
- Then you’ll see several messages about preparing Recovery process. Just wait till
the next screen comes up.
Recovery Software

3. Emergency Recovery (Using Norton ghost)

　STEP.1
- You’ll be asked to agree to License agreement of Symantec Co.
- Press “OK” to proceed.

　STEP.2
- You’ll be asked whether partition size is correct or not.
- Press “OK” to proceed.
Recovery Software

　STEP.3
- You’ll be asked to whether proceed with disk restore.
- Press “OK” if you don’t have any data to back up on your server.

　STEP.4
- Now you’ll see the proceeding status with bar graph.
- Wait till a pop-up window asks you to replace CD 1 with CD 2.
Recovery Software

　STEP.5
- When it reaches about 75%, you’ll be asked to insert CD 2.
- After replacing CD 1 with CD 2, press “OK” to proceed.

　STEP.6
- When it reaches 100%, you’ll be asked to whether continue or reset computer.
- Remove CD from your CD-ROM, then press “Reset computer”
Recovery Software

4. End of Procedure.

　STEP.1
- After pressing “Reset computer”, your server will reboot with Recovered data.
- When your server boot successfully, you’ll see an Error message.

　STEP.2
- Ignore the error message.
- Reboot the ENTIRE system to synchronize the whole data.
Recovery Software

5.ACONIS Server Restore Proc.

1. Remove the Lan cables(2 cables).


2. Restore system with ghost CD(Recovery CD) : The above procedure(Item 1-4)
3. rebooting( restart )
4. Change the network IP as follows;

(1) My Network Place 에 right click

(2) In Properties Window, Right Click on Local Connection 1


Recovery Software

3) In Properties window, select the Internet Protocal(TCP/IP)

(4) Set the IP Address


ex) ACONIS2 : 10.8.1.202
ACONIS3 : 10.8.1.203
Recovery Software

5) In Properties Window, Right Click on Local Connection 2

then repeat (3), (4)


Caution : You must set the IP Address, start 11..
Recovery Software

ex) ACONIS2 : 11.8.1.202


ACONIS3 : 11.8.1.203

5. Change the Computer Name


(1) My Computer icon 에 right click

(2) select ‘Network Identification’ tab, click the ‘Properties’ button


Recovery Software

(3) Change the ‘Computer Name’


ex) If N0.2 CRT , You must change “ACONIS2”
If No. 4 CRT , You must change “ACONIS4”

6. Connect the LAN cables again (2 cables)


7. Restart the computer

You might also like