Dar Vol2 Update Dec 2021
Uploaded by
sspawarDar Vol2 Update Dec 2021
Uploaded by
sspawarGOVERNMENT OF INDIA
(VOL. 2)
2021
© All rights reserved. No part of this publication, either in English or in Hindi, may be reproduced in any form or by
any means, electronic or mechanical including photocopy, recording or any information storage and retrieval system,
without permission, in writing, from the Director General, CPWD, New Delhi.
DISCLAIMER
The Delhi Analysis of Rates is indicative, as coefficients for labour are likely to vary due to technological innovations,
skill of workman and other local factors affecting the efficiency and output of labour. Further its use by Govt.
Departments, PSUs, private bodies & individuals shall be at their own discretion. CPWD shall not be responsible for
any ambiguity, discrepancy, dispute or financial loss, arising directly or indirectly by using or following items of Delhi
Analysis of Rates by such Govt./Private bodies or individuals.
For feedback and suggestions, please contact SE(TAS),CPWD, Room No. 418, ''A'' Wing, Nirman Bhawan,
New Delhi- 110011. Tel No. 01123062339. Email: [email protected]
A GOVERNMENT OF INDIA PUBLICATION
Published by
DIRECTOR GENERAL
CPWD, Nirman Bhawan, New Delhi - 110011
Printed & Marketed by
JAIN BOOK AGENCY (CENTRAL)
4638/21, Ground Floor, Ansari Road,
Daryaganj, Opp. Fire Station, New Delhi-110002
Phone : 011-43513689, 44556677 Mob: 9667274446, 8810566260
E-mail : [email protected]
Also available at
All Leading Booksellers & Authorised Govt. Dealers In India
Price : Rs. 3200/- (for both volumes) excluding postage and forwarding charges etc.
Hkkjr ljdkj dsUnzh; yksd fuekZ.k foHkkx
Government of India fuekZ.k Hkou] ubZ fnYyh 110011
Central Public Works Department
Vinit Kumar Jayaswal Nirman Bhawan, New Delhi- 110011
Director General Tel : 23062556 / 1317, Fax : 23061884
E-Mail : [email protected]
FOREWORD
Central Public Works Department Delhi Analysis of Rates 2021 is a
comprehensive and useful document forming basis for the rates of various
items of DSR 2021. It is based on scientific assessment of inputs of materials,
labour and machinery in various items of work normally involved in civil works.
It was first compiled in the year 1950, followed by subsequent publications or
revisions in the years 1955, 1962, 1972, 1977, 1985, 1997, 2007, 2012, 2013,
2014, 2016 and 2019.
Last edition of Delhi Analysis of Rates was published in the year 2019.
Revision of this DAR has become necessary due to changes in wages of
labour and prices of materials, adoption of new construction technologies &
materials as well as implementation of GST. This has necessitated revision of
existing Delhi Analysis of Rates 2019.
I wish to place on record the technical input and effective coordination on the
part of Shri D.C.Goel ADG (Tech.), Shri Vinayak Rai CE (CSQ) (Civil) and the
sincere efforts put in by Shri Divakar Agrawal SE (TAS), Shri S.N.Jaiswal
EE(TAS), Shri Mukesh Varma Chief Estimator, Shri Naveenkumar P JE (TAS),
Shri Chalapaka Ramaraju JE (TAS) and team of officers in CSQ unit in
preparation and finalizing the DAR 2021 in a short time.
I am sure that Delhi Analysis of Rates 2021 will be useful to all the engineers
and architects in Building Construction Industry in general and CPWD in
particular.
(Vinit Kumar Jayaswal)
Director General
Place : New Delhi
Date : July 12, 2021
Hkkjr ljdkj
Government of India
dsUnzh; yksd fuekZ.k foHkkx
fuekZ.k Hkou] ubZ fnYyh 110011
Dharmesh Chandra Goel Central Public Works Department
Addl. Director General (Tech) Nirman Bhawan, New Delhi- 110011
Tel : 23063389, Fax : 23061833
E-Mail : [email protected]
PREFACE
1. CPWD Delhi Analysis of Rates 2021 is the revised edition of CPWD Delhi Analysis of Rates for
Delhi 2019.
2. Delhi Analysis of Rates 2021 incorporates all the analysis of items of Delhi Schedule of Rates
2019 with updated correction slips, including analysis of existing items and also corresponding
new items introduced in DSR 2021.
3. Delhi Analysis of Rates 2021 is published in two volumes as under:
Volume Sub-head No. Content/ Sub-head
Number
One 00 Basic Rates
01 Carriage of Materials
02 Earth Work
03 Mortars
04 Concrete Work
05 Reinforced Cement Concrete
06 Masonry Work
07 Stone Work
08 Cladding Work
09 Wood and PVC Work
10 Steel Work
11 Flooring
12 Roofing
Two 13 Finishing
14 Repairs to Buildings
15 Dismantling and Demolishing
16 Road Work
17 Sanitary Installations
18 Water Supply
19 Drainage
20 Pile work
21 Aluminium Work
V
Volume Sub-head No. Content/ Sub-head
Number
22 Water Proofing
23 Rain Water Harvesting & Tubewells
24 Conservation of Heritage Buildings.
25 Structural Glazing Aluminium Composite Panel
26 New Technologies and Materials
4. Delhi Analysis of Rates 2021 is based on the study of current market rates of materials at Delhi,
prevailing as on or just before 01.04.2021. The basic rates of materials, incorporated in the analysis,
pertain to materials conforming to BIS Standards/ CPWD Specifications/Materials of good quality
generally available in the market. The effect of GST on works contracts has been incorporated in
all items. Labour rates are taken from the minimum wages issued by the Government of Delhi and
Govt. of India (whichever is higher) w.e.f. 01.04.2021.
5. The nomenclature of main items has been printed along with the analysis of first Sub item only to
conserve the space and number of pages.
6. Sundries have been considered as 2.12 times based on Cost Index of Delhi as on 01.04.2021
which is 105 over Delhi Plinth Area Rates 2020 with base 100 as on 01.04.2020 and cost
index as on 01.04.2020 which is 101 over CPWD Delhi Plinth Area Rates 2019 having base 100
as on 01.04.2019.
7. I wish to place on record the technical input and effective coordination on the part of Shri Vinayak
Rai CE (CSQ) (Civil) and the sincere efforts put in by Shri Divakar Agrawal SE (TAS), Shri
S.N.Jaiswal EE(TAS), Shri Mukesh Varma Chief Estimator, Shri Naveenkumar P JE (TAS), Shri
Chalapaka Ramaraju JE (TAS) and team of officers in CSQ unit in finalizing the DAR 2021 in a
short time.
8. I convey my gratitude to field offices at Delhi who rose to the occasion and provided sufficient data
base of market rates to CSQ office and thus enabled them to come out with this edition of DAR in
a short time.
9. Although due care has been taken in bringing out DAR 2021, there is possibility that some errors
are still there inadvertently. Error or omission may be brought to the notice of Superintending
Engineer (TAS), CPWD, Room No. 418A, A-wing, Nirman Bhawan, New Delhi -110011
(Tele fax. 011-23062339).
Suggestions for improvement are welcome.
Dharmesh Chandra Goel
ADG (Tech) CPWD
VI
C O N T E N T S
Vol. 1
SH. No. NAME OF SUB-HEAD PAGE No.
A. BASIC RATES
0.1 HIRE CHARGES OF PLANTS & MACHINERY 3-6
0.2 LABOUR 7-8
0.3 MATERIALS 9-74
0.4 CARRIAGE CODES 75-78
B. SUB -HEADS
1. Carriage of Materials 79-90
2. Earth Work 91-144
3. Mortars 145-154
4. Concrete Work 155-222
5. Reinforced Cement Concrete 223-338
6. Masonry Work 339-380
7. Stone Work 381-424
8. Cladding Work 425-484
9. Wood and PVC Work 485-734
10. Steel Work 735-780
11. Flooring 781-882
12. Roofing 883-992
VII
C O N T E N T S
Vol. 2
SH. No. NAME OF SUB-HEAD PAGE No.
13. Finishing 993-1090
14. Repairs to Building 1091-1158
15. Dismantling and Demolishing 1159-1208
16. Road Work 1209-1354
17. Sanitary Installations 1355-1472
18. Water Supply 1473-1802
19. Drainage 1803-1908
20. Pile work 1909-1940
21. Aluminium Work 1941-1974
22. Water Proofing 1975-2000
23. Rain Water Harvesting & Tubewells 2001-2026
24 Conservation of Heritage Buildings 2027-2034
25. Structural Glazing Aluminium Composite Panel 2035-2046
26. New Technologies and Materials 2047-2206
Note: For remaining Sub Heads refer to Vol. 1
VIII
SUB HEAD : 13.0
FINISHING
993
13.1 12 mm cement plaster of mix :
13.1.1 1:4 (1 cement: 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.144 3713.20 534.70
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2203.89 W
Add 1 % Water charges on "W" 22.04
TOTAL 2225.93 X
Add GST on "X" (multiplying
factor 0.1405) 312.74
TOTAL 2538.68 Y
Add 15% CPOH on "Y" 380.80
TOTAL 2919.48 Z
Add Cess @ 1% on "Z" 29.19
Cost of 10.00 sqm 2948.67
Cost of 1.00 sqm 294.87
Say 294.85
13.1.2 1:6 (1 cement: 6 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.144 3044.30 438.38
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2107.57 W
Add 1 % Water charges on "W" 21.08
TOTAL 2128.65 X
Add GST on "X" (multiplying
factor 0.1405) 299.08
TOTAL 2427.72 Y
Add 15% CPOH on "Y" 364.16
TOTAL 2791.88 Z
Add Cess @ 1% on "Z" 27.92
Cost of 10.00 sqm 2819.80
Cost of 1.00 sqm 281.98
Say 282.00
SUB HEAD : 13- FINISHING 995
13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :
13.2.1 1:4 (1 cement: 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.172 3713.20 638.67
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2539.06 W
Add 1 % Water charges on "W" 25.39
TOTAL 2564.45 X
Add GST on "X" (multiplying
factor 0.1405) 360.31
TOTAL 2924.76 Y
Add 15% CPOH on "Y" 438.71
TOTAL 3363.47 Z
Add Cess @ 1% on "Z" 33.63
Cost of 10.00 sqm 3397.11
Cost of 1.00 sqm 339.71
Say 339.70
13.2.2 1:6 (1 cement: 6 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.172 3044.30 523.62
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2424.01 W
Add 1 % Water charges on "W" 24.24
TOTAL 2448.25 X
Add GST on "X" (multiplying
factor 0.1405) 343.98
TOTAL 2792.23 Y
Add 15% CPOH on "Y" 418.83
TOTAL 3211.07 Z
Add Cess @ 1% on "Z" 32.11
Cost of 10.00 sqm 3243.18
Cost of 1.00 sqm 324.32
Say 324.30
SUB HEAD : 13- FINISHING 996
13.3 20 mm cement plaster of mix :
13.3.1 1:4 (1 cement: 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.224 3713.20 831.76
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3005.85 W
Add 1 % Water charges on "W" 30.06
TOTAL 3035.91 X
Add GST on "X" (multiplying
factor 0.1405) 426.55
TOTAL 3462.45 Y
Add 15% CPOH on "Y" 519.37
TOTAL 3981.82 Z
Add Cess @ 1% on "Z" 39.82
Cost of 10.00 sqm 4021.64
Cost of 1.00 sqm 402.16
Say 402.15
13.3.2 1:6 (1 cement: 6 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.224 3044.30 681.92
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2856.02 W
Add 1 % Water charges on "W" 28.56
TOTAL 2884.58 X
Add GST on "X" (multiplying
factor 0.1405) 405.28
TOTAL 3289.86 Y
Add 15% CPOH on "Y" 493.48
TOTAL 3783.34 Z
Add Cess @ 1% on "Z" 37.83
Cost of 10.00 sqm 3821.17
Cost of 1.00 sqm 382.12
Say 382.10
SUB HEAD : 13- FINISHING 997
13.4 12 mm cement plaster of mix :
13.4.1 1:4 (1 cement: 4 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.144 4355.20 627.15
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2296.34 W
Add 1 % Water charges on "W" 22.96
TOTAL 2319.31 X
Add GST on "X" (multiplying
factor 0.1405) 325.86
TOTAL 2645.17 Y
Add 15% CPOH on "Y" 396.78
TOTAL 3041.94 Z
Add Cess @ 1% on "Z" 30.42
Cost of 10.00 sqm 3072.36
Cost of 1.00 sqm 307.24
Say 307.25
13.4.2 1:6 (1 cement: 6 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 coarse sand)
3.11 Rate as per Item Number 3.11 of
SH: Mortars cum 0.144 3686.30 530.83
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2200.02 W
Add 1 % Water charges on "W" 22.00
TOTAL 2222.02 X
Add GST on "X" (multiplying
factor 0.1405) 312.19
TOTAL 2534.21 Y
Add 15% CPOH on "Y" 380.13
TOTAL 2914.35 Z
Add Cess @ 1% on "Z" 29.14
Cost of 10.00 sqm 2943.49
Cost of 1.00 sqm 294.35
Say 294.35
SUB HEAD : 13- FINISHING 998
13.5 15 mm cement plaster on rough side of single or half brick wall of mix:
13.5.1 1:4 (1 cement: 4 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.172 4355.20 749.09
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2649.49 W
Add 1 % Water charges on "W" 26.49
TOTAL 2675.98 X
Add GST on "X" (multiplying
factor 0.1405) 375.98
TOTAL 3051.96 Y
Add 15% CPOH on "Y" 457.79
TOTAL 3509.75 Z
Add Cess @ 1% on "Z" 35.10
Cost of 10.00 sqm 3544.85
Cost of 1.00 sqm 354.48
Say 354.50
13.5.2 1:6 (1 cement: 6 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 coarse sand)
3.11 Rate as per Item Number 3.11 of
SH: Mortars cum 0.172 3686.30 634.04
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2534.44 W
Add 1 % Water charges on "W" 25.34
TOTAL 2559.78 X
Add GST on "X" (multiplying
factor 0.1405) 359.65
TOTAL 2919.43 Y
Add 15% CPOH on "Y" 437.91
TOTAL 3357.34 Z
Add Cess @ 1% on "Z" 33.57
Cost of 10.00 sqm 3390.92
Cost of 1.00 sqm 339.09
Say 339.10
SUB HEAD : 13- FINISHING 999
13.6 20 mm cement plaster of mix :
13.6.1 1:4 (1 cement: 4 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.224 4355.20 975.56
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3149.66 W
Add 1 % Water charges on "W" 31.50
TOTAL 3181.15 X
Add GST on "X" (multiplying
factor 0.1405) 446.95
TOTAL 3628.11 Y
Add 15% CPOH on "Y" 544.22
TOTAL 4172.32 Z
Add Cess @ 1% on "Z" 41.72
Cost of 10.00 sqm 4214.05
Cost of 1.00 sqm 421.40
Say 421.40
13.6.2 1:6 (1 cement: 6 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 6 (1 cement :
6 coarse sand)
3.11 Rate as per Item Number 3.11 of
SH: Mortars cum 0.224 3686.30 825.73
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2999.82 W
Add 1 % Water charges on "W" 30.00
TOTAL 3029.82 X
Add GST on "X" (multiplying
factor 0.1405) 425.69
TOTAL 3455.51 Y
Add 15% CPOH on "Y" 518.33
TOTAL 3973.84 Z
Add Cess @ 1% on "Z" 39.74
Cost of 10.00 sqm 4013.58
Cost of 1.00 sqm 401.36
Say 401.35
SUB HEAD : 13- FINISHING 1000
13.7 12 mm cement plaster finished with a floating coat of neat cement of mix :
13.7.1 1:3 (1 cement: 3 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.144 4382.15 631.03
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 2796.60 W
Add 1 % Water charges on "W" 27.97
TOTAL 2824.57 X
Add GST on "X" (multiplying
factor 0.1405) 396.85
TOTAL 3221.42 Y
Add 15% CPOH on "Y" 483.21
TOTAL 3704.64 Z
Add Cess @ 1% on "Z" 37.05
Cost of 10.00 sqm 3741.68
Cost of 1.00 sqm 374.17
Say 374.15
13.7.2 1:4 (1 cement: 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.144 3713.20 534.70
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
SUB HEAD : 13- FINISHING 1001
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 2700.28 W
Add 1 % Water charges on "W" 27.00
TOTAL 2727.28 X
Add GST on "X" (multiplying
factor 0.1405) 383.18
TOTAL 3110.46 Y
Add 15% CPOH on "Y" 466.57
TOTAL 3577.03 Z
Add Cess @ 1% on "Z" 35.77
Cost of 10.00 sqm 3612.80
Cost of 1.00 sqm 361.28
Say 361.30
13.8 15 mm cement plaster on rough side of single or half brick wall finished with a
floating coat of neat cement of mix :
13.8.1 1:3 (1 cement: 3 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.172 4382.15 753.73
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 3150.50 W
Add 1 % Water charges on "W" 31.51
TOTAL 3182.01 X
Add GST on "X" (multiplying
factor 0.1405) 447.07
TOTAL 3629.08 Y
Add 15% CPOH on "Y" 544.36
TOTAL 4173.44 Z
Add Cess @ 1% on "Z" 41.73
Cost of 10.00 sqm 4215.18
Cost of 1.00 sqm 421.52
Say 421.50
SUB HEAD : 13- FINISHING 1002
13.8.2 1:4 (1 cement: 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.172 3713.20 638.67
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 3035.45 W
Add 1 % Water charges on "W" 30.35
TOTAL 3065.80 X
Add GST on "X" (multiplying
factor 0.1405) 430.74
TOTAL 3496.54 Y
Add 15% CPOH on "Y" 524.48
TOTAL 4021.03 Z
Add Cess @ 1% on "Z" 40.21
Cost of 10.00 sqm 4061.24
Cost of 1.00 sqm 406.12
Say 406.10
13.9 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of
neat cement.
13.9.1 12 mm cement plaster
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:3 (1 cement :
3 coarse sand)
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.144 5024.15 723.48
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
SUB HEAD : 13- FINISHING 1003
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 2889.05 W
Add 1 % Water charges on "W" 28.89
TOTAL 2917.94 X
Add GST on "X" (multiplying
factor 0.1405) 409.97
TOTAL 3327.91 Y
Add 15% CPOH on "Y" 499.19
TOTAL 3827.10 Z
Add Cess @ 1% on "Z" 38.27
Cost of 10.00 sqm 3865.37
Cost of 1.00 sqm 386.54
Say 386.55
13.9.2 20 mm cement plaster
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:3 (1 cement :
3 coarse sand)
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.224 5024.15 1125.41
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 3795.88 W
Add 1 % Water charges on "W" 37.96
TOTAL 3833.84 X
Add GST on "X" (multiplying
factor 0.1405) 538.65
TOTAL 4372.50 Y
Add 15% CPOH on "Y" 655.87
TOTAL 5028.37 Z
Add Cess @ 1% on "Z" 50.28
Cost of 10.00 sqm 5078.66
Cost of 1.00 sqm 507.87
Say 507.85
SUB HEAD : 13- FINISHING 1004
13.10 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating
coat of neat cement on the rough side of single or half brick wall.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:3 (1 cement :
3 coarse sand)
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.172 5024.15 864.15
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 3260.93 W
Add 1 % Water charges on "W" 32.61
TOTAL 3293.54 X
Add GST on "X" (multiplying
factor 0.1405) 462.74
TOTAL 3756.28 Y
Add 15% CPOH on "Y" 563.44
TOTAL 4319.72 Z
Add Cess @ 1% on "Z" 43.20
Cost of 10.00 sqm 4362.92
Cost of 1.00 sqm 436.29
Say 436.30
13.11 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5
(1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster
1:6 (1 cement : 6 fine sand).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Under layer Cement mortar
1 : 5 (1 cement : 5 coarse sand)
3.10 Rate as per Item Number 3.10 of
SH: Mortars cum 0.144 3995.00 575.28
Top layer Cement mortar
1 : 6 (1 cement : 6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.072 3044.30 219.19
LABOUR
0155 Mason (average) day 1.21 749.00 906.29
0115 Coolie day 1.29 645.00 832.05
0101 Bhisti day 1.05 714.00 749.70
SUB HEAD : 13- FINISHING 1005
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3309.24 W
Add 1 % Water charges on "W" 33.09
TOTAL 3342.34 X
Add GST on "X" (multiplying
factor 0.1405) 469.60
TOTAL 3811.93 Y
Add 15% CPOH on "Y" 571.79
TOTAL 4383.72 Z
Add Cess @ 1% on "Z" 43.84
Cost of 10.00 sqm 4427.56
Cost of 1.00 sqm 442.76
Say 442.75
13.12 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5
(1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1
cement : 3 coarse sand) finished rough with sponge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Under layer Cement mortar
1 : 5 (1 cement : 5 coarse sand)
3.10 Rate as per Item Number 3.10 of
SH: Mortars cum 0.144 3995.00 575.28
Top layer Cement mortar
1:3 (1 cement : 3 coarse sand)
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.072 5024.15 361.74
LABOUR
0155 Mason (average) day 1.21 749.00 906.29
0115 Coolie day 1.29 645.00 832.05
0101 Bhisti day 1.05 714.00 749.70
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3451.79 W
Add 1 % Water charges on “W” 34.52
TOTAL 3486.31 X
Add GST on “X” (multiplying
factor 0.1405) 489.83
TOTAL 3976.14 Y
Add 15% CPOH on “Y” 596.42
TOTAL 4572.56 Z
Add Cess @ 1% on “Z” 45.73
Cost of 10.00 sqm 4618.28
Cost of 1.00 sqm 461.83
Say 461.85
SUB HEAD : 13- FINISHING 1006
13.13 12 mm cement plaster 1:2 (1 cement : 2 stone dust).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:2 (1 Cement :
2 stone dust)
3.12 Rate as per Item Number 3.12 of
SH: Mortars cum 0.144 5319.25 765.97
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2435.17 W
Add 1 % Water charges on "W" 24.35
TOTAL 2459.52 X
Add GST on "X" (multiplying
factor 0.1405) 345.56
TOTAL 2805.08 Y
Add 15% CPOH on "Y" 420.76
TOTAL 3225.84 Z
Add Cess @ 1% on "Z" 32.26
Cost of 10.00 sqm 3258.10
Cost of 1.00 sqm 325.81
Say 325.80
13.14 15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single
or half brick wall.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:2 (1 Cement :
2 stone dust)
3.12 Rate as per Item Number 3.12 of
SH: Mortars cum 0.172 5319.25 914.91
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0115 Coolie day 0.88 645.00 567.60
0101 Bhisti day 0.99 714.00 706.86
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2815.30 W
Add 1 % Water charges on "W" 28.15
TOTAL 2843.46 X
Add GST on "X" (multiplying
factor 0.1405) 399.51
TOTAL 3242.96 Y
Add 15% CPOH on "Y" 486.44
TOTAL 3729.41 Z
Add Cess @ 1% on "Z" 37.29
Cost of 10.00 sqm 3766.70
Cost of 1.00 sqm 376.67
Say 376.65
SUB HEAD : 13- FINISHING 1007
13.15 20 mm cement plaster 1:2 (1 cement : 2 stone dust).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:2 (1 Cement :
2 stone dust)
3.12 Rate as per Item Number 3.12 of
SH: Mortars cum 0.224 5319.25 1191.51
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3365.61 W
Add 1 % Water charges on “W” 33.66
TOTAL 3399.26 X
Add GST on “X” (multiplying
factor 0.1405) 477.60
TOTAL 3876.86 Y
Add 15% CPOH on “Y” 581.53
TOTAL 4458.39 Z
Add Cess @ 1% on “Z” 44.58
Cost of 10.00 sqm 4502.97
Cost of 1.00 sqm 450.30
Say 450.30
13.16 6 mm cement plaster of mix :
13.16.1 1:3 (1 cement : 3 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.072 4382.15 315.51
LABOUR
0155 Mason (average) day 0.51 749.00 381.99
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Extra for removing burrs, cleaning with
wire brushes, pock making with pointed
tool etc. complete. L.S. 13.39 2.12 28.39
9999 Scaffolding and sundries L.S. 11.70 2.12 24.80
TOTAL 1891.33 W
Add 1 % Water charges on "W" 18.91
TOTAL 1910.24 X
Add GST on "X" (multiplying
factor 0.1405) 268.39
TOTAL 2178.63 Y
Add 15% CPOH on "Y" 326.79
TOTAL 2505.42 Z
Add Cess @ 1% on "Z" 25.05
Cost of 10.00 sqm 2530.48
Cost of 1.00 sqm 253.05
Say 253.05
SUB HEAD : 13- FINISHING 1008
13.17 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of
neat cement and thick coat of Lime wash on top of walls when dry for bearing
of R.C.C. slabs and beams.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.072 4382.15 315.51
LABOUR
0155 Mason (average) day 0.51 749.00 381.99
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Extra for removing burrs, cleaning with
wire brushes, pock making with pointed
tool etc. complete. L.S. 13.39 2.12 28.39
9999 Scaffolding and sundries L.S. 11.7 2.12 24.80
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
0776 Satna lime quintal 0.01 370.00 3.70
9999 Indigo gum etc L.S. 2.08 2.12 4.41
9999 Sundries ladder etc. L.S. 0.52 2.12 1.10
0141 White Washer day 0.07 714.00 49.98
0115 Coolie day 0.07 645.00 45.15
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 2497.84 W
Add 1 % Water charges on “W” 24.98
TOTAL 2522.82 X
Add GST on “X” (multiplying
factor 0.1405) 354.46
TOTAL 2877.27 Y
Add 15% CPOH on “Y” 431.59
TOTAL 3308.86 Z
Add Cess @ 1% on “Z” 33.09
Cost of 10.00 sqm 3341.95
Cost of 1.00 sqm 334.19
Say 334.20
13.18 Neat cement punning.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0367 Portland Cement (OPC-43 grade) tonne 0.022 5000.00 110.00
2209 Carriage of Cement tonne 0.022 145.72 3.21
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
SUB HEAD : 13- FINISHING 1009
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 506.67 W
Add 1 % Water charges on "W" 5.07
TOTAL 511.74 X
Add GST on "X" (multiplying
factor 0.1405) 71.90
TOTAL 583.64 Y
Add 15% CPOH on "Y" 87.55
TOTAL 671.19 Z
Add Cess @ 1% on "Z" 6.71
Cost of 10.00 sqm 677.90
Cost of 1.00 sqm 67.79
Say 67.80
13.19 Rough cast plaster upto 10 m height above ground level with a mixture of sand
and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over
and including the fresh plaster in two layers, under layer 12 mm cement plaster
1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement
: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.
13.19.1 Ordinary cement finish using ordinary cement
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Under layer 12 mm thick cement plaster
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.144 4355.20 627.15
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0114 Beldar day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
Top layer 10 mm thick cement plaster
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.12 4382.15 525.86
0155 Mason (average) day 0.61 749.00 456.89
0114 Beldar day 0.69 645.00 445.05
0101 Bhisti day 0.85 714.00 606.90
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
1179 Crushed stone 2.36 mm to
12.5 mm size cum 0.10 900.00 90.00
0101 Bhisti day 0.01 714.00 7.14
0777 Dry hydrated lime (factory made) quintal 0.09 290.00 26.10
9977 Carriage of lime L.S. 3.64 2.12 7.72
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.50 645.00 322.50
0101 Bhisti day 0.10 714.00 71.40
SUB HEAD : 13- FINISHING 1010
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
Labour for scooping
0123 Mason (brick layer) 1st class day 0.25 784.00 196.00
0114 Beldar day 0.25 645.00 161.25
TOTAL 5623.75 W
Add 1 % Water charges on “W” 56.24
TOTAL 5679.99 X
Add GST on “X” (multiplying
factor 0.1405) 798.04
TOTAL 6478.03 Y
Add 15% CPOH on “Y” 971.70
TOTAL 7449.73 Z
Add Cess @ 1% on “Z” 74.50
Cost of 10.00 sqm 7524.23
Cost of 1.00 sqm 752.42
Say 752.40
13.20 Pebble dash plaster upto 10 m height above ground level with a mixture of
washed pebble or crushed stone 6 mm to 12.5 mm nominal size, dashed over
and including fresh plaster in two layers under layer 12 mm cement plaster 1:4
(1 cement : 4 coarse sand) and top layer 10 mm cement plaster with cement
mortar 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated
lime by volume of cement.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Under layer 12 mm thick cement plaster
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.144 4355.20 627.15
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0114 Beldar day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
Top layer 10 mm thick cement plaster
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.12 4382.15 525.86
0155 Mason (average) day 0.61 749.00 456.89
0114 Beldar day 0.69 645.00 445.05
0101 Bhisti day 0.85 714.00 606.90
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
1179 Crushed stone 2.36 mm to 12.5 mm size cum 0.10 900.00 90.00
0101 Bhisti day 0.01 714.00 7.14
0777 Dry hydrated lime (factory made) quintal 0.09 290.00 26.10
9977 Carriage of lime L.S. 3.64 2.12 7.72
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.50 645.00 322.50
SUB HEAD : 13- FINISHING 1011
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.10 714.00 71.40
9999 Scaffolding and sundries L.S. 9.88 2.12 20.95
9999 Scaffolding and sundries L.S. 4.42 2.12 9.37
TOTAL 5275.87 W
Add 1 % Water charges on "W" 52.76
TOTAL 5328.63 X
Add GST on "X" (multiplying
factor 0.1405) 748.67
TOTAL 6077.30 Y
Add 15% CPOH on "Y" 911.60
TOTAL 6988.90 Z
Add Cess @ 1% on "Z" 69.89
Cost of 10.00 sqm 7058.79
Cost of 1.00 sqm 705.88
Say 705.90
13.21 Extra for providing and mixing water proofing material in cement plaster work
in proportion recommended by the manufacturers.
Code Description Unit Quantity Rate Amount
Detail of cost for 12mm cement
plaster 1:3
(1 cement :3 sand) = 10 sqm or
1.48 bags of cement used in the mix.
Cement required for 10 sqm = 73.89kg.
Water proofing material required @
1 kg per 50 kg of cement = 1.48 kg.
1213 Water proofing materials kilogram 1.48 35.00 51.80
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 66.96 W
Add 1 % Water charges on "W" 0.67
TOTAL 67.63 X
Add GST on "X" (multiplying
factor 0.1405) 9.50
TOTAL 77.13 Y
Add 15% CPOH on "Y" 11.57
TOTAL 88.70 Z
Add Cess @ 1% on "Z" 0.89
Cost of 1.48 bags of cement used
in the mix. 89.59
Cost of 1.00 bag of 50 kg cement
used in the mix. 60.53
Say 60.55
13.22 Extra for plastering exterior walls of height more than 10 m from ground level
for every additional height of 3 m or part thereof.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
9999 Scaffolding and sundries L.S. 53.82 2.12 114.10
SUB HEAD : 13- FINISHING 1012
Code Description Unit Quantity Rate Amount
LABOUR
0155 Mason (average) day 0.20 749.00 149.80
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.10 714.00 71.40
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 543.96 W
Add 1 % Water charges on “W” 5.44
TOTAL 549.40 X
Add GST on “X” (multiplying
factor 0.1405) 77.19
TOTAL 626.59 Y
Add 15% CPOH on “Y” 93.99
TOTAL 720.57 Z
Add Cess @ 1% on “Z” 7.21
Cost of 10.00 sqm 727.78
Cost of 1.00 sqm 72.78
Say 72.80
13.23 Extra for plastering on circular work not exceeding 6 m in radius:
13.23.1 In one coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 293.96 W
Add 1 % Water charges on “W” 2.94
TOTAL 296.90 X
Add GST on “X” (multiplying
factor 0.1405) 41.71
TOTAL 338.61 Y
Add 15% CPOH on “Y” 50.79
TOTAL 389.40 Z
Add Cess @ 1% on “Z” 3.89
Cost of 10.00 sqm 393.30
Cost of 1.00 sqm 39.33
Say 39.35
13.23.2 In two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.30 749.00 224.70
0114 Beldar day 0.30 645.00 193.50
SUB HEAD : 13- FINISHING 1013
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 446.59 W
Add 1 % Water charges on “W” 4.47
TOTAL 451.05 X
Add GST on “X” (multiplying
factor 0.1405) 63.37
TOTAL 514.43 Y
Add 15% CPOH on “Y” 77.16
TOTAL 591.59 Z
Add Cess @ 1% on “Z” 5.92
Cost of 10.00 sqm 597.51
Cost of 1.00 sqm 59.75
Say 59.75
13.24 Extra for plastering done on moulding, cornices or architraves including neat
finish to line and level:
13.24.1 In one coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 3.00 749.00 2247.00
0114 Beldar day 2.00 645.00 1290.00
0115 Coolie day 1.00 645.00 645.00
0101 Bhisti day 0.25 714.00 178.50
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 4388.89 W
Add 1 % Water charges on "W" 43.89
TOTAL 4432.78 X
Add GST on "X" (multiplying
factor 0.1405) 622.80
TOTAL 5055.58 Y
Add 15% CPOH on "Y" 758.34
TOTAL 5813.92 Z
Add Cess @ 1% on "Z" 58.14
Cost of 10.00 sqm 5872.06
Cost of 1.00 sqm 587.21
Say 587.20
13.24.2 In two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 5.00 749.00 3745.00
0114 Beldar day 3.00 645.00 1935.00
0115 Coolie day 2.00 645.00 1290.00
0101 Bhisti day 0.33 714.00 235.62
SUB HEAD : 13- FINISHING 1014
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 7234.01 W
Add 1 % Water charges on "W" 72.34
TOTAL 7306.35 X
Add GST on "X" (multiplying
factor 0.1405) 1026.54
TOTAL 8332.89 Y
Add 15% CPOH on "Y" 1249.93
TOTAL 9582.82 Z
Add Cess @ 1% on "Z" 95.83
Cost of 10.00 sqm 9678.65
Cost of 1.00 sqm 967.87
Say 967.85
13.25 Extra for plastering:
13.25.1 Spherical ceiling
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.75 749.00 561.75
0114 Beldar day 0.74 645.00 477.30
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 1096.10 W
Add 1 % Water charges on "W" 10.96
TOTAL 1107.06 X
Add GST on "X" (multiplying
factor 0.1405) 155.54
TOTAL 1262.60 Y
Add 15% CPOH on "Y" 189.39
TOTAL 1451.99 Z
Add Cess @ 1% on "Z" 14.52
Cost of 10.00 sqm 1466.51
Cost of 1.00 sqm 146.65
Say 146.65
13.25.2 Groined ceiling
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.80 749.00 599.20
0114 Beldar day 0.80 645.00 516.00
9999 Sundries L.S. 34.06 2.12 72.21
TOTAL 1187.41 W
Add 1 % Water charges on "W" 11.87
TOTAL 1199.28 X
Add GST on "X" (multiplying
factor 0.1405) 168.50
TOTAL 1367.78 Y
Add 15% CPOH on "Y" 205.17
TOTAL 1572.95 Z
Add Cess @ 1% on "Z" 15.73
Cost of 10.00 sqm 1588.68
Cost of 1.00 sqm 158.87
Say 158.85
SUB HEAD : 13- FINISHING 1015
13.25.3 Flewing soffits
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 725.39 W
Add 1 % Water charges on “W” 7.25
TOTAL 732.64 X
Add GST on “X” (multiplying
factor 0.1405) 102.94
TOTAL 835.58 Y
Add 15% CPOH on “Y” 125.34
TOTAL 960.91 Z
Add Cess @ 1% on “Z” 9.61
Cost of 10.00 sqm 970.52
Cost of 1.00 sqm 97.05
Say 97.05
13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered
surface to prepare the surface even and smooth complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Plaster of paris 10x0.002x1121 = 22.42kg
Add 2% wastage= 0.45kg
Total = 22.87kg. Say23kg
0869 Plaster of Paris kilogram 23.00 5.00 115.00
9977 Carriage of plaster of paris L.S. 3.90 2.12 8.27
LABOUR
0122 Mason (for plaster of paris work)
1st class day 0.91 784.00 713.44
0114 Beldar day 0.91 645.00 586.95
9999 Scaffolding and sundries L.S. 83.98 2.12 178.04
TOTAL 1601.70 W
Add 1 % Water charges on “W” 16.02
TOTAL 1617.71 X
Add GST on “X” (multiplying
factor 0.1405) 227.29
TOTAL 1845.00 Y
Add 15% CPOH on “Y” 276.75
TOTAL 2121.75 Z
Add Cess @ 1% on “Z” 21.22
Cost of 10.00 sqm 2142.97
Cost of 1.00 sqm 214.30
Say 214.30
SUB HEAD : 13- FINISHING 1016
13.27 Extra for lining out plaster to imitate stone or concrete blocks walling.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.50 645.00 322.50
9999 Solution of lime putty L.S. 1.82 2.12 3.86
TOTAL 700.86 W
Add 1 % Water charges on “W” 7.01
TOTAL 707.87 X
Add GST on “X” (multiplying
factor 0.1405) 99.46
TOTAL 807.32 Y
Add 15% CPOH on “Y” 121.10
TOTAL 928.42 Z
Add Cess @ 1% on “Z” 9.28
Cost of 10.00 sqm 937.70
Cost of 1.00 sqm 93.77
Say 93.75
13.28 12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine
sand):
13.28.1 Flush Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.014 3713.20 51.98
LABOUR
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
0101 Bhisti day 0.05 714.00 35.70
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 467.10 W
Add 1 % Water charges on "W" 4.67
TOTAL 471.77 X
Add GST on "X" (multiplying
factor 0.1405) 66.28
TOTAL 538.05 Y
Add 15% CPOH on "Y" 80.71
TOTAL 618.76 Z
Add Cess @ 1% on "Z" 6.19
Cost of 10.00 metre long and
10 cm wide band 624.95
Cost of 1.00 metre long and
1 cm wide band 6.25
Say 6.25
SUB HEAD : 13- FINISHING 1017
13.28.2 Sunk Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.014 3713.20 51.98
LABOUR
0155 Mason (average) day 0.30 749.00 224.70
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Sundries L.S. 2.08 2.12 4.41
TOTAL 510.29 W
Add 1 % Water charges on “W” 5.10
TOTAL 515.40 X
Add GST on “X” (multiplying
factor 0.1405) 72.41
TOTAL 587.81 Y
Add 15% CPOH on “Y” 88.17
TOTAL 675.98 Z
Add Cess @ 1% on “Z” 6.76
Cost of 10.00 metre long and 10 cm
wide band 682.74
Cost of 1.00 metre long and 1 cm
wide band 6.83
Say 6.85
13.28.3 Raised Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.014 3713.20 51.98
LABOUR
0155 Mason (average) day 0.35 749.00 262.15
0115 Coolie day 0.35 645.00 225.75
0101 Bhisti day 0.05 714.00 35.70
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 581.37 W
Add 1 % Water charges on “W” 5.81
TOTAL 587.19 X
Add GST on “X” (multiplying
factor 0.1405) 82.50
TOTAL 669.69 Y
Add 15% CPOH on “Y” 100.45
TOTAL 770.14 Z
Add Cess @ 1% on “Z” 7.70
Cost of 10.00 metre long and 10 cm
wide band 777.84
Cost of 1.00 metre long and 1 cm
wide band 7.78
Say 7.80
SUB HEAD : 13- FINISHING 1018
13.28.4 Moulded Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.014 3713.20 51.98
LABOUR
0155 Mason (average) day 0.65 749.00 486.85
0115 Coolie day 0.65 645.00 419.25
0101 Bhisti day 0.05 714.00 35.70
9999 Sundries L.S. 1.56 2.12 3.31
TOTAL 997.09 W
Add 1 % Water charges on “W” 9.97
TOTAL 1007.06 X
Add GST on “X” (multiplying
factor 0.1405) 141.49
TOTAL 1148.56 Y
Add 15% CPOH on “Y” 172.28
TOTAL 1320.84 Z
Add Cess @ 1% on “Z” 13.21
Cost of 10.00 metre long and 10 cm
wide band 1334.05
Cost of 1.00 metre long and 1 cm
wide band 13.34
Say 13.35
13.29 18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine
sand):
13.29.1 Flush Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.02 3713.20 74.26
LABOUR
0155 Mason (average) day 0.32 749.00 239.68
0115 Coolie day 0.32 645.00 206.40
0101 Bhisti day 0.06 714.00 42.84
SUB HEAD : 13- FINISHING 1019
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.08 2.12 4.41
TOTAL 567.59 W
Add 1 % Water charges on "W" 5.68
TOTAL 573.27 X
Add GST on "X" (multiplying
factor 0.1405) 80.54
TOTAL 653.81 Y
Add 15% CPOH on "Y" 98.07
TOTAL 751.89 Z
Add Cess @ 1% on "Z" 7.52
Cost of 10.00 metre long and 10 cm
wide band 759.40
Cost of 1.00 metre long and 1 cm
wide band 7.59
Say 7.60
13.29.2 Sunk Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.02 3713.20 74.26
LABOUR
0155 Mason (average) day 0.36 749.00 269.64
0115 Coolie day 0.36 645.00 232.20
0101 Bhisti day 0.06 714.00 42.84
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 624.73 W
Add 1 % Water charges on "W" 6.25
TOTAL 630.98 X
Add GST on "X" (multiplying
factor 0.1405) 88.65
TOTAL 719.63 Y
Add 15% CPOH on "Y" 107.94
TOTAL 827.58 Z
Add Cess @ 1% on "Z" 8.28
Cost of 10.00 metre long and 10 cm
wide band 835.85
Cost of 1.00 metre long and 1 cm
wide band 8.36
Say 8.35
SUB HEAD : 13- FINISHING 1020
13.29.3 Raised Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.02 3713.20 74.26
LABOUR
0155 Mason (average) day 0.42 749.00 314.58
0115 Coolie day 0.42 645.00 270.90
0101 Bhisti day 0.06 714.00 42.84
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 711.95 W
Add 1 % Water charges on "W" 7.12
TOTAL 719.07 X
Add GST on "X" (multiplying
factor 0.1405) 101.03
TOTAL 820.10 Y
Add 15% CPOH on "Y" 123.02
TOTAL 943.12 Z
Add Cess @ 1% on "Z" 9.43
Cost of 10.00 metre long and 10 cm
wide band 952.55
Cost of 1.00 metre long and 1 cm
wide band 9.53
Say 9.55
13.29.4 Moulded Band
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.40 Rate as per Item Number 3.4 of
SH: Mortars cum 0.024 3713.20 89.12
LABOUR
0155 Mason (average) day 0.86 749.00 644.14
0115 Coolie day 0.86 645.00 554.70
0101 Bhisti day 0.05 714.00 35.70
SUB HEAD : 13- FINISHING 1021
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 1329.44 W
Add 1 % Water charges on "W" 13.29
TOTAL 1342.74 X
Add GST on "X" (multiplying
factor 0.1405) 188.65
TOTAL 1531.39 Y
Add 15% CPOH on "Y" 229.71
TOTAL 1761.10 Z
Add Cess @ 1% on "Z" 17.61
Cost of 10.00 metre long and 10 cm
wide band 1778.71
Cost of 1.00 metre long and 1 cm
wide band 17.79
Say 17.80
13.30 18 mm thick moulded cement mortar band in two coats under layer 12 mm thick
with cement mortar 1:5 (1 cement : 5 coarse sand) top layer 6 mm thick with
cement mortar 1:4 (1 cement : 4 fine sand).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre long and
10 cm wide band
MATERIAL
Cement mortar 1 : 5 (1 cement :
5 coarse sand)
3.10 Rate as per Item Number 3.10 of
SH: Mortars cum 0.014 3995.00 55.93
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.01 3713.20 37.13
LABOUR
0155 Mason (average) day 0.86 749.00 644.14
0115 Coolie day 0.86 645.00 554.70
0101 Bhisti day 0.05 714.00 35.70
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 1333.39 W
Add 1 % Water charges on "W" 13.33
TOTAL 1346.72 X
Add GST on "X" (multiplying
factor 0.1405) 189.21
TOTAL 1535.94 Y
Add 15% CPOH on "Y" 230.39
TOTAL 1766.33 Z
Add Cess @ 1% on "Z" 17.66
Cost of 10.00 metre long and 10 cm
wide band 1783.99
Cost of 1.00 metre long and 1 cm
wide band 17.84
Say 17.85
SUB HEAD : 13- FINISHING 1022
13.31 Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3
fine sand):
13.31.1 Flush / Ruled/ Struck or weathered pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.03 4382.15 131.46
LABOUR
0155 Mason (average) day 0.50 749.00 374.50
0115 Coolie day 0.60 645.00 387.00
0101 Bhisti day 0.93 714.00 664.02
9999 Sundries L.S. 7.15 2.12 15.16
9999 Scaffolding and racking out joints
including sundries L.S. 14.30 2.12 30.32
TOTAL 1602.46 W
Add 1 % Water charges on “W” 16.02
TOTAL 1618.48 X
Add GST on “X” (multiplying
factor 0.1405) 227.40
TOTAL 1845.88 Y
Add 15% CPOH on “Y” 276.88
TOTAL 2122.76 Z
Add Cess @ 1% on “Z” 21.23
Cost of 10.00 sqm 2143.99
Cost of 1.00 sqm 214.40
Say 214.40
13.31.2 Raised and cut pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.046 4382.15 201.58
LABOUR
0155 Mason (average) day 1.07 749.00 801.43
0115 Coolie day 1.31 645.00 844.95
0101 Bhisti day 1.00 714.00 714.00
9999 Sundries L.S. 7.15 2.12 15.16
SUB HEAD : 13- FINISHING 1023
Code Description Unit Quantity Rate Amount
9999 Scaffolding and racking out joints
including sundries L.S. 16.12 2.12 34.17
TOTAL 2611.29 W
Add 1 % Water charges on “W” 26.11
TOTAL 2637.40 X
Add GST on “X” (multiplying
factor 0.1405) 370.56
TOTAL 3007.96 Y
Add 15% CPOH on “Y” 451.19
TOTAL 3459.15 Z
Add Cess @ 1% on “Z” 34.59
Cost of 10.00 sqm 3493.74
Cost of 1.00 sqm 349.37
Say 349.35
13.32 Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand):
13.32.1 Flush/ Ruled/ Struck or weathered pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.046 4382.15 201.58
9999 Sundries L.S. 7.15 2.12 15.16
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.80 645.00 516.00
0101 Bhisti day 1.28 714.00 913.92
9999 Scaffolding and racking out joints
including sundries L.S. 16.12 2.12 34.17
TOTAL 2182.66 W
Add 1 % Water charges on “W” 21.83
TOTAL 2204.49 X
Add GST on “X” (multiplying
factor 0.1405) 309.73
TOTAL 2514.22 Y
Add 15% CPOH on “Y” 377.13
TOTAL 2891.35 Z
Add Cess @ 1% on “Z” 28.91
Cost of 10.00 sqm 2920.26
Cost of 1.00 sqm 292.03
Say 292.05
13.33 Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :
13.33.1 Flush/ Ruled pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
SUB HEAD : 13- FINISHING 1024
Code Description Unit Quantity Rate Amount
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.023 4382.15 100.79
9999 Sundries L.S. 7.15 2.12 15.16
LABOUR
0155 Mason (average) day 0.92 749.00 689.08
0115 Coolie day 1.37 645.00 883.65
0101 Bhisti day 0.93 714.00 664.02
9999 Scaffolding and racking out joints
including sundries L.S. 16.12 2.12 34.17
TOTAL 2386.87 W
Add 1 % Water charges on “W” 23.87
TOTAL 2410.74 X
Add GST on “X” (multiplying
factor 0.1405) 338.71
TOTAL 2749.45 Y
Add 15% CPOH on “Y” 412.42
TOTAL 3161.87 Z
Add Cess @ 1% on “Z” 31.62
Cost of 10.00 sqm 3193.49
Cost of 1.00 sqm 319.35
Say 319.35
13.33.2 Raised and cut pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.038 4382.15 166.52
9999 Sundries L.S. 7.15 2.12 15.16
LABOUR
0155 Mason (average) day 2.00 749.00 1498.00
0115 Coolie day 2.96 645.00 1909.20
0101 Bhisti day 1.00 714.00 714.00
9999 Scaffolding and racking out joints
including sundries L.S. 16.12 2.12 34.17
TOTAL 4337.05 W
Add 1 % Water charges on "W" 43.37
TOTAL 4380.42 X
Add GST on "X" (multiplying
factor 0.1405) 615.45
TOTAL 4995.87 Y
Add 15% CPOH on "Y" 749.38
TOTAL 5745.26 Z
Add Cess @ 1% on "Z" 57.45
Cost of 10.00 sqm 5802.71
Cost of 1.00 sqm 580.27
Say 580.25
SUB HEAD : 13- FINISHING 1025
13.34 Raised and cut pointing on stone work in white cement mortar 1:3 (1 white
cement : 3 marble dust).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
White Cement mortar 1:3 (1 white
cement : 3 marble dust)
3.16 Rate as per Item Number 3.16 of
SH: Mortars cum 0.038 7790.25 296.03
9999 Sundries L.S. 7.15 2.12 15.16
LABOUR
0155 Mason (average) day 2.00 749.00 1498.00
0115 Coolie day 2.96 645.00 1909.20
0101 Bhisti day 1.00 714.00 714.00
9999 Scaffolding and racking out joints
including sundries L.S. 16.12 2.12 34.17
TOTAL 4466.56 W
Add 1 % Water charges on “W” 44.67
TOTAL 4511.23 X
Add GST on “X” (multiplying
factor 0.1405) 633.83
TOTAL 5145.05 Y
Add 15% CPOH on “Y” 771.76
TOTAL 5916.81 Z
Add Cess @ 1% on “Z” 59.17
Cost of 10.00 sqm 5975.98
Cost of 1.00 sqm 597.60
Say 597.60
13.35 Pointing on stone slab ceiling with cement mortar 1:2 (1 cement : 2 fine sand):
13.35.1 Flush/ Ruled pointing
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1:2 (1 cement :
2 fine sand)
3.2 Rate as per Item Number 3.2 of
SH: Mortars cum 0.015 5129.25 76.94
LABOUR
0155 Mason (average) day 0.47 749.00 352.03
0115 Coolie day 0.69 645.00 445.05
0101 Bhisti day 0.59 714.00 421.26
9999 Scaffolding and racking out joints
including
sundries L.S. 16.12 2.12 34.17
TOTAL 1329.45 W
Add 1 % Water charges on "W" 13.29
TOTAL 1342.75 X
Add GST on "X" (multiplying
factor 0.1405) 188.66
TOTAL 1531.40 Y
Add 15% CPOH on "Y" 229.71
TOTAL 1761.11 Z
Add Cess @ 1% on "Z" 17.61
Cost of 10.00 sqm 1778.73
Cost of 1.00 sqm 177.87
Say 177.85
SUB HEAD : 13- FINISHING 1026
13.36 Extra for pointing on walls on the outside at height more than 10 m from ground
level for every additional height of 3 m or part there of.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
9999 Scaffolding L.S. 13.39 2.12 28.39
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 56.77 W
Add 1 % Water charges on "W" 0.57
TOTAL 57.34 X
Add GST on "X" (multiplying
factor 0.1405) 8.06
TOTAL 65.40 Y
Add 15% CPOH on "Y" 9.81
TOTAL 75.21 Z
Add Cess @ 1% on "Z" 0.75
Cost of 10.00 sqm 75.96
Cost of 1.00 sqm 7.60
Say 7.60
13.37 White washing with lime to give an even shade :
13.37.1 New work (three or more coats)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0775 Dehradun white lime quintal 0.03 600.00 18.00
9977 Carriage of lime L.S. 0.91 2.12 1.93
LABOUR
0141 White Washer day 0.20 714.00 142.80
0115 Coolie day 0.10 645.00 64.50
9999 Indigo gum etc L.S. 4.42 2.12 9.37
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 242.39 W
Add 1 % Water charges on “W” 2.42
TOTAL 244.81 X
Add GST on “X” (multiplying
factor 0.1405) 34.40
TOTAL 279.21 Y
Add 15% CPOH on “Y” 41.88
TOTAL 321.09 Z
Add Cess @ 1% on “Z” 3.21
Cost of 10.00 sqm 324.30
Cost of 1.00 sqm 32.43
Say 32.45
SUB HEAD : 13- FINISHING 1027
13.38 Satna lime wash on walls with one coat.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0776 Satna lime quintal 0.01 370.00 3.70
9977 Carriage of lime L.S. 2.08 2.12 4.41
9999 Indigo gum etc L.S. 0.52 2.12 1.10
LABOUR
0141 White Washer day 0.08 714.00 57.12
0115 Coolie day 0.04 645.00 25.80
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 97.92 W
Add 1 % Water charges on “W” 0.98
TOTAL 98.90 X
Add GST on “X” (multiplying
factor 0.1405) 13.90
TOTAL 112.79 Y
Add 15% CPOH on “Y” 16.92
TOTAL 129.71 Z
Add Cess @ 1% on “Z” 1.30
Cost of 10.00 sqm 131.01
Cost of 1.00 sqm 13.10
Say 13.10
13.39 Colour washing such as green, blue or buff to give an even shade :
13.39.1 New work (two or more coats) with a base coat of white washing with lime
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0775 Dehradun white lime quintal 0.03 600.00 18.00
9977 Carriage of lime L.S. 8.06 2.12 17.09
9999 Add for colouring stuff L.S. 0.91 2.12 1.93
LABOUR
0141 White Washer day 0.30 714.00 214.20
0115 Coolie day 0.10 645.00 64.50
9999 Indigo gum etc L.S. 4.42 2.12 9.37
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 330.87 W
Add 1 % Water charges on "W" 3.31
TOTAL 334.18 X
Add GST on "X" (multiplying
factor 0.1405) 46.95
TOTAL 381.14 Y
Add 15% CPOH on "Y" 57.17
TOTAL 438.31 Z
Add Cess @ 1% on "Z" 4.38
Cost of 10.00 sqm 442.69
Cost of 1.00 sqm 44.27
Say 44.25
SUB HEAD : 13- FINISHING 1028
13.39.2 New work (two or more coats) with a base coat of whiting
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0775 Dehradun white lime quintal 0.03 600.00 18.00
9977 Carriage of lime L.S. 8.06 2.12 17.09
9999 Add for colouring stuff L.S. 0.91 2.12 1.93
LABOUR
0141 White Washer day 0.30 714.00 214.20
0115 Coolie day 0.10 645.00 64.50
9999 Indigo gum etc L.S. 2.73 2.12 5.79
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 327.29 W
Add 1 % Water charges on “W” 3.27
TOTAL 330.56 X
Add GST on “X” (multiplying
factor 0.1405) 46.44
TOTAL 377.01 Y
Add 15% CPOH on “Y” 56.55
TOTAL 433.56 Z
Add Cess @ 1% on “Z” 4.34
Cost of 10.00 sqm 437.90
Cost of 1.00 sqm 43.79
Say 43.80
13.41 Distempering with oil bound washable distemper of approved brand and
manufacture to give an even shade :
13.41.1 New work (two or more coats) over and including water thinnable priming coat
with cement primer
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0808 Water thinnable cement primer for
interior wall surface, having VOC
content less than 50 gms/lit. litre 0.70 50.00 35.00
9999 Brushes, putty etc L.S. 7.15 2.12 15.16
9988 Sundries including Carriage L.S. 8.06 2.12 17.09
0802 Acrylic distemper 1st quality , having
VOC content less than 50 grams/ litre kilogram 1.50 40.00 60.00
9977 Carriage of material L.S. 4.42 2.12 9.37
9999 Brushes, sand paper and putty for filling
holes L.S. 11.70 2.12 24.80
LABOUR
0131 Painter day 1.00 714.00 714.00
0115 Coolie day 0.50 645.00 322.50
SUB HEAD : 13- FINISHING 1029
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1215.01 W
Add 1 % Water charges on “W” 12.15
TOTAL 1227.16 X
Add GST on “X” (multiplying
factor 0.1405) 172.42
TOTAL 1399.57 Y
Add 15% CPOH on “Y” 209.94
TOTAL 1609.51 Z
Add Cess @ 1% on “Z” 16.10
Cost of 10.00 sqm 1625.60
Cost of 1.00 sqm 162.56
Say 162.55
13.42 Distempering with 1st quality acrylic distemper (ready mixed) having VOC
content less than 50 gms/litre, of approved manufacturer, of required shade
and colour complete, as per manufacturer's specification.
13.42.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0802 Acrylic distemper 1st quality , having
VOC content less than 50 grams/ litre kilogram 1.50 40.00 60.00
9977 Carriage of material L.S. 4.42 2.12 9.37
9999 Brushes, sand paper and putty for
filling holes L.S. 11.57 2.12 24.53
LABOUR
0131 Painter day 0.40 714.00 285.60
0114 Beldar day 0.46 645.00 296.70
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 693.29 W
Add 1 % Water charges on “W” 6.93
TOTAL 700.22 X
Add GST on “X” (multiplying
factor 0.1405) 98.38
TOTAL 798.60 Y
Add 15% CPOH on “Y” 119.79
TOTAL 918.39 Z
Add Cess @ 1% on “Z” 9.18
Cost of 10.00 sqm 927.57
Cost of 1.00 sqm 92.76
Say 92.75
SUB HEAD : 13- FINISHING 1030
13.43 Applying one coat of water thinnable cement primer of approved brand and
manufacture on wall surface :
13.43.1 Water thinnable cement primer
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0808 Water thinnable cement primer for
interior wall surface, having VOC
content less than 50 gms/lit. litre 0.70 50.00 35.00
9999 Brushes, putty etc L.S. 7.15 2.12 15.16
LABOUR
0131 Painter day 0.40 714.00 285.60
0115 Coolie day 0.20 645.00 129.00
9988 Sundries including carriage L.S. 8.06 2.12 17.09
TOTAL 481.85 W
Add 1 % Water charges on "W" 4.82
TOTAL 486.66 X
Add GST on "X" (multiplying
factor 0.1405) 68.38
TOTAL 555.04 Y
Add 15% CPOH on "Y" 83.26
TOTAL 638.30 Z
Add Cess @ 1% on "Z" 6.38
Cost of 10.00 sqm 644.68
Cost of 1.00 sqm 64.47
Say 64.45
13.44 Finishing walls with water proofing cement paint of required shade :
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0851 Water proofing cement paint kilogram 3.84 38.00 145.92
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.46 714.00 328.44
0115 Coolie day 0.23 645.00 148.35
0101 Bhisti day 0.10 714.00 71.40
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 729.66 W
Add 1 % Water charges on "W" 7.30
TOTAL 736.96 X
Add GST on "X" (multiplying
factor 0.1405) 103.54
TOTAL 840.50 Y
Add 15% CPOH on "Y" 126.08
TOTAL 966.58 Z
Add Cess @ 1% on "Z" 9.67
Cost of 10.00 sqm 976.24
Cost of 1.00 sqm 97.62
Say 97.60
SUB HEAD : 13- FINISHING 1031
13.45 Finishing walls with textured exterior paint of required shade :
13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including
priming coat of exterior primer applied @ 2.20kg/10 sqm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8507 Textured exterior paint litre 3.28 280.00 918.40
0837 Acrylic Exterior Primer kilogram 2.20 100.00 220.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.02 2.12 14.88
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1831.28 W
Add 1 % Water charges on “W” 18.31
TOTAL 1849.59 X
Add GST on “X” (multiplying
factor 0.1405) 259.87
TOTAL 2109.46 Y
Add 15% CPOH on “Y” 316.42
TOTAL 2425.88 Z
Add Cess @ 1% on “Z” 24.26
Cost of 10.00 sqm 2450.13
Cost of 1.00 sqm 245.01
Say 245.00
13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :
13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming
coat of exterior primer applied @ 2.20 kg/10 sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8505 Acrylic exterior paint litre 1.67 200.00 334.00
0837 Acrylic Exterior Primer Kg 2.20 100.00 220.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1247.15 W
Add 1 % Water charges on "W" 12.47
TOTAL 1259.62 X
Add GST on "X" (multiplying
factor 0.1405) 176.98
TOTAL 1436.60 Y
Add 15% CPOH on "Y" 215.49
TOTAL 1652.09 Z
Add Cess @ 1% on "Z" 16.52
Cost of 10.00 sqm 1668.61
Cost of 1.00 sqm 166.86
Say 166.85
SUB HEAD : 13- FINISHING 1032
13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone
additives of required shade:
13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including
priming coat of exterior primer applied @ 2.20 kg/10 sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8506 Premium Acrylic exterior paint litre 1.43 210.00 300.30
0837 Acrylic Exterior Primer kilogram 2.20 100.00 220.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1213.45 W
Add 1 % Water charges on "W" 12.13
TOTAL 1225.59 X
Add GST on "X" (multiplying
factor 0.1405) 172.19
TOTAL 1397.78 Y
Add 15% CPOH on "Y" 209.67
TOTAL 1607.45 Z
Add Cess @ 1% on "Z" 16.07
Cost of 10.00 sqm 1623.52
Cost of 1.00 sqm 162.35
Say 162.35
13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using
Primer as per manufacturers specifications :
13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one
coat of Special primer applied @ 0.75 ltr /10 sqm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8504 Multi surface paint litre 1.25 300.00 375.00
8509 Special Primer (C.W.) litre 0.75 160.00 120.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.02 2.12 14.88
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1187.88 W
Add 1 % Water charges on "W" 11.88
TOTAL 1199.76 X
Add GST on "X" (multiplying factor 0.1405) 168.57
TOTAL 1368.32 Y
Add 15% CPOH on "Y" 205.25
TOTAL 1573.57 Z
Add Cess @ 1% on "Z" 15.74
Cost of 10.00 sqm 1589.31
Cost of 1.00 sqm 158.93
Say 158.95
SUB HEAD : 13- FINISHING 1033
13.48.2 Painting wood work with Deluxe Multi Surface Paint of required shade. Two or
more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75
ltr/10 sqm of approved brand and manufacture
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8504 Multi surface paint litre 0.90 300.00 270.00
8509 Special Primer (C.W.) litre 0.75 160.00 120.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.02 2.12 14.88
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1082.88 W
Add 1 % Water charges on "W" 10.83
TOTAL 1093.71 X
Add GST on "X" (multiplying
factor 0.1405) 153.67
TOTAL 1247.37 Y
Add 15% CPOH on "Y" 187.11
TOTAL 1434.48 Z
Add Cess @ 1% on "Z" 14.34
Cost of 10.00 sqm 1448.82
Cost of 1.00 sqm 144.88
Say 144.90
13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two
or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @
0.80 ltr/10 sqm of approved brand and manufacture
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8504 Multi surface paint litre 0.90 300.00 270.00
8510 Metal Primer (U.G.) litre 0.80 105.00 84.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.30 645.00 193.50
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.02 2.12 14.88
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1046.88 W
Add 1 % Water charges on "W" 10.47
TOTAL 1057.35 X
Add GST on "X" (multiplying
factor 0.1405) 148.56
TOTAL 1205.90 Y
Add 15% CPOH on "Y" 180.89
TOTAL 1386.79 Z
Add Cess @ 1% on "Z" 13.87
Cost of 10.00 sqm 1400.66
Cost of 1.00 sqm 140.07
Say 140.05
SUB HEAD : 13- FINISHING 1034
13.48A Finishing walls with 100% Premium acrylic emulsion paint having VOC less
than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal
resistance, dirt resistance exterior paint of required shade (Company Depot
Tinted) with silicon additives.
13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including
priming coat of exterior primer applied @ 0.90 litre/10 sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm (Based on
item no 13.47)
Material
0836 100% Premium acrylic dirt resistance,
Silicone additives exterior paint litre 1.43 270.00 386.10
0837 Acrylic Exterior Primer litre 0.90 100.00 90.00
9977 Carriage of material L.S. 1.56 2.12 3.31
Labour
0131 Painter day 0.45 714.00 321.30
0101 Bhisti day 0.45 714.00 321.30
9999 Brushes, sand paper etc. L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
Total 1154.25 W
Add 1 % Water charges on "W" 11.54
TOTAL 1165.79 X
Add GST on "X" (multiplying
factor 0.1405) 163.79
TOTAL 1329.59 Y
Add 15% CPOH on "Y" 199.44
TOTAL 1529.03 Z
Add Cess @ 1% on "Z" 15.29
Cost of 10 sqm 1544.32
Cost of 1 sqm 154.43
Say 154.45
13.50 Applying priming coat:
13.50.1 With ready mixed pink or Grey primer of approved brand and manufacture on
wood work (hard and soft wood)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0806 Ready mixed pink or grey primer on
wood work (hard and soft wood) having
VOC content less than 50 grams/ litre litre 0.75 105.00 78.75
9999 Putty L.S. 2.73 2.12 5.79
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
SUB HEAD : 13- FINISHING 1035
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 459.29 W
Add 1 % Water charges on "W" 4.59
TOTAL 463.88 X
Add GST on "X" (multiplying
factor 0.1405) 65.18
TOTAL 529.06 Y
Add 15% CPOH on "Y" 79.36
TOTAL 608.42 Z
Add Cess @ 1% on "Z" 6.08
Cost of 10.00 sqm 614.50
Cost of 1.00 sqm 61.45
Say 61.45
13.50.2 With ready mixed aluminium primer of approved brand and manufacture on
resinous wood and plywood
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
4201 Aluminium primer litre 0.75 120.00 90.00
9999 Putty L.S. 2.73 2.12 5.79
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 470.54 W
Add 1 % Water charges on "W" 4.71
TOTAL 475.24 X
Add GST on "X" (multiplying
factor 0.1405) 66.77
TOTAL 542.02 Y
Add 15% CPOH on "Y" 81.30
TOTAL 623.32 Z
Add Cess @ 1% on "Z" 6.23
Cost of 10.00 sqm 629.55
Cost of 1.00 sqm 62.96
Say 62.95
13.50.3 With ready mixed red oxide zinc chromate primer of approved brand and
manufacture on steel galvanised iron/ steel works
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.54 120.00 64.80
9977 Carriage L.S. 0.52 2.12 1.10
SUB HEAD : 13- FINISHING 1036
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.24 714.00 171.36
0115 Coolie day 0.24 645.00 154.80
9999 Brushes,sand paper including sundries L.S. 10.79 2.12 22.87
TOTAL 414.94 W
Add 1 % Water charges on "W" 4.15
TOTAL 419.09 X
Add GST on "X" (multiplying
factor 0.1405) 58.88
TOTAL 477.97 Y
Add 15% CPOH on "Y" 71.70
TOTAL 549.66 Z
Add Cess @ 1% on "Z" 5.50
Cost of 10.00 sqm 555.16
Cost of 1.00 sqm 55.52
Say 55.50
13.50.4 With ready mixed red oxide zinc chromate primer of approved brand and
manufacture on steel work (second coat)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.36 120.00 43.20
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.12 714.00 85.68
0115 Coolie day 0.12 645.00 77.40
9999 Brushes,sand paper including L.S. 7.15 2.12 15.16
TOTAL 222.26 W
Add 1 % Water charges on "W" 2.22
TOTAL 224.49 X
Add GST on "X" (multiplying
factor 0.1405) 31.54
TOTAL 256.03 Y
Add 15% CPOH on "Y" 38.40
TOTAL 294.43 Z
Add Cess @ 1% on "Z" 2.94
Cost of 10.00 sqm 297.38
Cost of 1.00 sqm 29.74
Say 29.75
13.51 Painting with silicon & acrylic emulsion based water thinnable sealer of approved
brand and manufacture on wet or patchy portion of plastered surfaces :
13.51.1 One coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0801 Silicon and acrylic emulsion litre 1.80 120.00 216.00
9977 Carriage of material L.S. 0.52 2.12 1.10
9999 Putty etc L.S. 2.73 2.12 5.79
SUB HEAD : 13- FINISHING 1037
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.27 714.00 192.78
0115 Coolie day 0.27 645.00 174.15
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 623.99 W
Add 1 % Water charges on "W" 6.24
TOTAL 630.23 X
Add GST on "X" (multiplying
factor 0.1405) 88.55
TOTAL 718.78 Y
Add 15% CPOH on "Y" 107.82
TOTAL 826.60 Z
Add Cess @ 1% on "Z" 8.27
Cost of 10.00 sqm 834.87
Cost of 1.00 sqm 83.49
Say 83.50
13.51.2 Two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0801 Silicon and acrylic emulsion litre 2.88 120.00 345.60
9977 Carriage of material L.S. 0.52 2.12 1.10
9999 Putty etc L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.43 714.00 307.02
0115 Coolie day 0.43 645.00 277.35
9999 Brushes, sand paper etc L.S. 8.53 2.12 18.08
9999 Sundries L.S. 17.26 2.12 36.59
TOTAL 991.53 W
Add 1 % Water charges on "W" 9.92
TOTAL 1001.45 X
Add GST on "X" (multiplying
factor 0.1405) 140.70
TOTAL 1142.15 Y
Add 15% CPOH on "Y" 171.32
TOTAL 1313.48 Z
Add Cess @ 1% on "Z" 13.13
Cost of 10.00 sqm 1326.61
Cost of 1.00 sqm 132.66
Say 132.65
13.52 Finishing with Epoxy paint (two or more coats) at all locations prepared and
applied as per manufacturer's specifications including appropriate priming coat,
preparation of surface, etc. complete.
13.52.1 On steel work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
PRIMING COAT
SUB HEAD : 13- FINISHING 1038
Code Description Unit Quantity Rate Amount
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.75 120.00 90.00
9999 Putty L.S. 2.73 2.12 5.79
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc L.S. 5.46 2.12 11.58
9999 Sundries L.S. 10.66 2.12 22.60
EPOXY PAINTING
MATERIAL
7239 Epoxy paint litre 1.25 215.00 268.75
9977 Carriage of material L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Putty, brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1507.60 W
Add 1 % Water charges on "W" 15.08
TOTAL 1522.67 X
Add GST on "X" (multiplying
factor 0.1405) 213.94
TOTAL 1736.61 Y
Add 15% CPOH on "Y" 260.49
TOTAL 1997.10 Z
Add Cess @ 1% on "Z" 19.97
Cost of 10.00 sqm 2017.07
Cost of 1.00 sqm 201.71
Say 201.70
13.52.2 On concrete work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
PRIMING COAT
MATERIAL
0808 Water thinnable cement primer for
interior wall surface, having VOC
content less than 50 grams/ litre litre 0.84 50.00 42.00
9999 Putty L.S. 13.52 2.12 28.66
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc L.S. 2.73 2.12 5.79
9999 Sundries L.S. 8.06 2.12 17.09
EPOXY PAINTING
MATERIAL
7239 Epoxy paint litre 1.21 215.00 260.15
9999 Materials for filling in holes
and cracks L.S. 6.76 2.12 14.33
9977 Carriage of material L.S. 1.43 2.12 3.03
SUB HEAD : 13- FINISHING 1039
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Putty, brushes, sand paper etc L.S. 10.79 2.12 22.87
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 1482.97 W
Add 1 % Water charges on "W" 14.83
TOTAL 1497.80 X
Add GST on "X" (multiplying
factor 0.1405) 210.44
TOTAL 1708.24 Y
Add 15% CPOH on "Y" 256.24
TOTAL 1964.47 Z
Add Cess @ 1% on "Z" 19.64
Cost of 10.00 sqm 1984.12
Cost of 1.00 sqm 198.41
Say 198.40
13.53 Painting on G.S. sheet with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade :
13.53.1 New work (two or more coats) including a coat of approved steel primer but
excluding a coat of mordant solution
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
PRIMING COAT
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.36 120.00 43.20
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.12 714.00 85.68
0114 Beldar day 0.12 645.00 77.40
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
Synthetic enamel painting
MATERIAL
0834 Synthetic enamel paint in all shades
except black or chocolate shade litre 0.80 165.00 132.00
9977 Carriage L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Putty, brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1122.57 W
Add 1 % Water charges on "W" 11.23
TOTAL 1133.80 X
Add GST on "X" (multiplying
factor 0.1405) 159.30
TOTAL 1293.10 Y
Add 15% CPOH on "Y" 193.96
TOTAL 1487.06 Z
Add Cess @ 1% on "Z" 14.87
Cost of 10.00 sqm 1501.94
Cost of 1.00 sqm 150.19
Say 150.20
SUB HEAD : 13- FINISHING 1040
13.54 Applying a coat of mordant solution on G.S. sheet:
13.54.1 With a solution of 38 gms of copper acetate in a litre of soft water
Code Description Unit Quantity Rate Amount
Detail of cost for 25 sqm
MATERIAL
4203 Copper acetate kilogram 0.038 300.00 11.40
9999 Soft Water L.S. 1.82 2.12 3.86
9977 Carriage L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.60 645.00 387.00
9999 Brushes, sand paper etc L.S. 35.88 2.12 76.07
9999 Sundries L.S. 35.88 2.12 76.07
TOTAL 984.72 W
Add 1 % Water charges on "W" 9.85
TOTAL 994.57 X
Add GST on "X" (multiplying
factor 0.1405) 139.74
TOTAL 1134.30 Y
Add 15% CPOH on "Y" 170.15
TOTAL 1304.45 Z
Add Cess @ 1% on "Z" 13.04
Cost of 25 sqm 1317.49
Cost of 1.00 sqm 52.70
Say 52.70
13.54.2 With a solution made of 13 gms of hydrochloric acid in a solution of 13 gms
each of copper chloride, copper nitrate and ammonium chloride dissolved in a
litre of soft water
Code Description Unit Quantity Rate Amount
Detail of cost for 25 sqm
MATERIAL
4204 Hydrochloric acid kilogram 0.013 35.00 0.46
4205 Copper chloride kilogram 0.013 300.00 3.90
4206 Copper nitrate kilogram 0.013 210.00 2.73
4207 Ammonium chloride kilogram 0.013 22.00 0.29
9999 Soft Water L.S. 1.82 2.12 3.86
9977 Carriage L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 0.60 714.00 428.40
0115 Coolie day 0.60 645.00 387.00
9999 Brushes, sand paper etc L.S. 35.88 2.12 76.07
9999 Sundries L.S. 35.88 2.12 76.07
TOTAL 980.69 W
Add 1 % Water charges on "W" 9.81
TOTAL 990.50 X
Add GST on "X" (multiplying
factor 0.1405) 139.16
TOTAL 1129.66 Y
Add 15% CPOH on "Y" 169.45
TOTAL 1299.11 Z
Add Cess @ 1% on "Z" 12.99
Cost of 25 sqm 1312.10
Cost of 1.00 sqm 52.48
Say 52.50
SUB HEAD : 13- FINISHING 1041
13.55 Painting (two or more coats) on rain water, soil waste and vent pipes and fittings
with black anticorrosive bitumastic paint of approved brand and manufacture,
over and including a priming of ready mixed zinc chromate yellow primer on
new work:
13.55.1 100 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Area=22/7 x106.4mm x30m =10.032sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.54 120.00 64.80
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.24 714.00 171.36
0115 Coolie day 0.24 645.00 154.80
9999 Brushes, sand paper etc L.S. 10.79 2.12 22.87
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.95 100.00 95.00
9977 Carriage L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Putty, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
9999 Wire brushes for cleaning L.S. 5.33 2.12 11.30
9999 Extra for delays L.S. 61.10 2.12 129.53
TOTAL 1416.05 W
Add 1 % Water charges on "W" 14.16
TOTAL 1430.21 X
Add GST on "X" (multiplying
factor 0.1405) 200.94
TOTAL 1631.15 Y
Add 15% CPOH on "Y" 244.67
TOTAL 1875.82 Z
Add Cess @ 1% on "Z" 18.76
Cost of 30.00 mtrs 1894.58
Cost of 1.00 metre 63.15
Say 63.15
13.55.2 150 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Area=22/7 x0.1572 m x30m =14.82sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.80 120.00 96.00
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 15.99 2.12 33.90
9977 Carriage L.S. 0.91 2.12 1.93
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 1.41 100.00 141.00
9977 Carriage L.S. 2.08 2.12 4.41
LABOUR
0131 Painter day 0.80 714.00 571.20
0115 Coolie day 0.80 645.00 516.00
SUB HEAD : 13- FINISHING 1042
Code Description Unit Quantity Rate Amount
9999 Putty, sand paper etc L.S. 8.06 2.12 17.09
9999 Sundries L.S. 11.96 2.12 25.36
9999 Wire brushes for cleaning L.S. 7.15 2.12 15.16
9999 Extra for delays L.S. 94.12 2.12 199.53
TOTAL 2110.81 W
Add 1 % Water charges on "W" 21.11
TOTAL 2131.92 X
Add GST on "X" (multiplying
factor 0.1405) 299.53
TOTAL 2431.46 Y
Add 15% CPOH on "Y" 364.72
TOTAL 2796.17 Z
Add Cess @ 1% on "Z" 27.96
Cost of 30.00 mtrs 2824.14
Cost of 1.00 metre 94.14
Say 94.15
13.56 Painting (two or more coats) on rain water, soil waste and vent pipes and fittings
with synthetic enamel paint of approved brand and manufacture and required
colour over a priming coat of approved steel primer on new work.
13.56.1 100 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Area=22/7x0.1064m x30m =10.032sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.54 120.00 64.80
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.24 714.00 171.36
0115 Coolie day 0.24 645.00 154.80
9999 Sundries L.S. 10.79 2.12 22.87
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 1.16 175.00 203.00
9977 Carriage L.S. 1.43 2.12 3.03
9999 Putty, sand paper etc L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Sundries L.S. 6.76 2.12 14.33
9999 Wire brushes for cleaning L.S. 11.96 2.12 25.36
9999 Extra for delays L.S. 66.43 2.12 140.83
TOTAL 1546.65 W
Add 1 % Water charges on "W" 15.47
TOTAL 1562.11 X
Add GST on "X" (multiplying
factor 0.1405) 219.48
TOTAL 1781.59 Y
Add 15% CPOH on "Y" 267.24
TOTAL 2048.83 Z
Add Cess @ 1% on "Z" 20.49
Cost of 30.00 mtrs 2069.32
Cost of 1.00 metre 68.98
Say 69.00
SUB HEAD : 13- FINISHING 1043
13.56.2 150 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Area=22/7 x157.2mm x30m =14.82sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.80 120.00 96.00
9977 Carriage L.S. 0.65 2.12 1.38
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Sundries L.S. 15.99 2.12 33.90
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 1.72 175.00 301.00
9977 Carriage L.S. 2.08 2.12 4.41
9999 Putty, sand paper etc L.S. 7.93 2.12 16.81
LABOUR
0131 Painter day 0.80 714.00 571.20
0115 Coolie day 0.80 645.00 516.00
9999 Sundries L.S. 10.01 2.12 21.22
9999 Wire brushes for cleaning L.S. 17.81 2.12 37.76
9999 Extra for delays L.S. 101.40 2.12 214.97
TOTAL 2303.88 W
Add 1 % Water charges on "W" 23.04
TOTAL 2326.92 X
Add GST on "X" (multiplying
factor 0.1405) 326.93
TOTAL 2653.86 Y
Add 15% CPOH on "Y" 398.08
TOTAL 3051.93 Z
Add Cess @ 1% on "Z" 30.52
Cost of 30.00 mtrs 3082.45
Cost of 1.00 metre 102.75
Say 102.75
13.57 Painting with oil type wood preservative of approved brand and manufacture :
13.57.1 New work (two or more coats)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0859 Oil type wood preservative litre 1.00 130.00 130.00
9977 Carriage of material L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.15 714.00 107.10
0115 Coolie day 0.15 645.00 96.75
9999 Brushes etc L.S. 4.16 2.12 8.82
SUB HEAD : 13- FINISHING 1044
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 3.90 2.12 8.27
TOTAL 352.04 W
Add 1 % Water charges on "W" 3.52
TOTAL 355.56 X
Add GST on "X" (multiplying
factor 0.1405) 49.96
TOTAL 405.52 Y
Add 15% CPOH on "Y" 60.83
TOTAL 466.34 Z
Add Cess @ 1% on "Z" 4.66
Cost of 10.00 sqm 471.01
Cost of 1.00 sqm 47.10
Say 47.10
13.58 Providing and applying two coats of fire retardant paint on cleaned wood / ply
surface @ 3.5 sqm per litre per coat including preparation of base surface as
per recommendations of manufacturer to make the surface fire retardant.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
7240 Fire retardant paint litre 5.70 240.00 1368.00
9977 Carriage of material L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0114 Beldar day 0.54 645.00 348.30
9999 Putty, brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 2136.31 W
Add 1 % Water charges on “W” 21.36
TOTAL 2157.67 X
Add GST on “X” (multiplying
factor 0.1405) 303.15
TOTAL 2460.83 Y
Add 15% CPOH on “Y” 369.12
TOTAL 2829.95 Z
Add Cess @ 1% on “Z” 28.30
Cost of 10.00 sqm 2858.25
Cost of 1.00 sqm 285.82
Say 285.80
13.59 Coal tarring two coats on new work using 0.16 Litre and 0.12 litre coal tar per
sqm in the first coat and second coat respectively.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
9999 Lime L.S. 1.43 2.12 3.03
0324 Coal Tar litre 2.80 30.00 84.00
9977 Carriage of material L.S. 1.43 2.12 3.03
0771 Kerosene oil litre 0.50 50.00 25.00
SUB HEAD : 13- FINISHING 1045
Code Description Unit Quantity Rate Amount
LABOUR
0114 Beldar day 0.43 645.00 277.35
9999 Brushes etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 415.01 W
Add 1 % Water charges on "W" 4.15
TOTAL 419.16 X
Add GST on "X" (multiplying
factor 0.1405) 58.89
TOTAL 478.05 Y
Add 15% CPOH on "Y" 71.71
TOTAL 549.76 Z
Add Cess @ 1% on "Z" 5.50
Cost of 10.00 sqm 555.26
Cost of 1.00 sqm 55.53
Say 55.55
13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture
to give an even shade :
13.60.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0804 Premium plastic acrylic emulsion of
interior grade, having VOC content less
than 50 grams/ litre litre 1.21 200.00 242.00
9999 For filling holes and cracks with putty etc L.S. 6.76 2.12 14.33
9977 Carriage of material L.S. 1.43 2.12 3.03
LABOUR 0.00
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc L.S. 10.79 2.12 22.87
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 1030.43 W
Add 1 % Water charges on "W" 10.30
TOTAL 1040.73 X
Add GST on "X" (multiplying
factor 0.1405) 146.22
TOTAL 1186.96 Y
Add 15% CPOH on "Y" 178.04
TOTAL 1365.00 Z
Add Cess @ 1% on "Z" 13.65
Cost of 10.00 sqm 1378.65
Cost of 1.00 sqm 137.86
Say 137.85
SUB HEAD : 13- FINISHING 1046
13.61 Painting with synthetic enamel paint of approved brand and manufacture to
give an even shade :
13.61.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 1.16 175.00 203.00
9999 For filling holes and cracks with putty etc L.S. 5.33 2.12 11.30
9977 Carriage L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 982.61 W
Add 1 % Water charges on "W" 9.83
TOTAL 992.44 X
Add GST on "X" (multiplying
factor 0.1405) 139.44
TOTAL 1131.87 Y
Add 15% CPOH on "Y" 169.78
TOTAL 1301.65 Z
Add Cess @ 1% on "Z" 13.02
Cost of 10.00 sqm 1314.67
Cost of 1.00 sqm 131.47
Say 131.45
13.62 Painting with synthetic enamel paint of approved brand and manufacture of
required colour to give an even shade :
13.62.1 Two or more coats on new work over an under coat of suitable shade with
ordinary paint of approved brand and manufacture
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0806 Ready mixed pink or grey primer on
wood work (hard and soft wood) having
VOC content less than 50 grams/ litre litre 0.75 105.00 78.75
9999 Putty L.S. 2.73 2.12 5.79
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 10.79 2.12 22.87
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 1.16 175.00 203.00
9977 Carriage of paint and material L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
SUB HEAD : 13- FINISHING 1047
Code Description Unit Quantity Rate Amount
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1430.60 W
Add 1 % Water charges on "W" 14.31
TOTAL 1444.90 X
Add GST on "X" (multiplying
factor 0.1405) 203.01
TOTAL 1647.91 Y
Add 15% CPOH on "Y" 247.19
TOTAL 1895.10 Z
Add Cess @ 1% on "Z" 18.95
Cost of 10.00 sqm 1914.05
Cost of 1.00 sqm 191.41
Say 191.40
13.63 Painting with aluminium paint of approved brand and manufacture to give an
even shade .
13.63.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0826 Aluminium paint litre 0.80 150.00 120.00
9977 Carriage of paint and material L.S. 1.43 2.12 3.03
9999 Putty etc L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 11.96 2.12 25.36
TOTAL 907.88 W
Add 1 % Water charges on "W" 9.08
TOTAL 916.96 X
Add GST on "X" (multiplying
factor 0.1405) 128.83
TOTAL 1045.79 Y
Add 15% CPOH on "Y" 156.87
TOTAL 1202.66 Z
Add Cess @ 1% on "Z" 12.03
Cost of 10.00 sqm 1214.68
Cost of 1.00 sqm 121.47
Say 121.45
13.64 Painting with acid proof paint of approved brand and manufacture of required
colour to give an even shade :
13.64.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0827 Acid proof paint (chocolate or black) litre 1.16 225.00 261.00
SUB HEAD : 13- FINISHING 1048
Code Description Unit Quantity Rate Amount
9977 Carriage of paint L.S. 1.43 2.12 3.03
9999 Putty etc L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1040.61 W
Add 1 % Water charges on "W" 10.41
TOTAL 1051.02 X
Add GST on "X" (multiplying
factor 0.1405) 147.67
TOTAL 1198.68 Y
Add 15% CPOH on "Y" 179.80
TOTAL 1378.49 Z
Add Cess @ 1% on "Z" 13.78
Cost of 10.00 sqm 1392.27
Cost of 1.00 sqm 139.23
Say 139.25
13.65 Painting with black anti-corrosive bitumastic paint of approved brand and
manufacture to give an even shade :
13.65.1 Two or more coats on new work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.95 100.00 95.00
9977 Carriage L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Putty, brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 860.28 W
Add 1 % Water charges on "W" 8.60
TOTAL 868.88 X
Add GST on "X" (multiplying
factor 0.1405) 122.08
TOTAL 990.96 Y
Add 15% CPOH on "Y" 148.64
TOTAL 1139.60 Z
Add Cess @ 1% on "Z" 11.40
Cost of 10.00 sqm 1151.00
Cost of 1.00 sqm 115.10
Say 115.10
SUB HEAD : 13- FINISHING 1049
13.67 Varnishing with varnish of approved brand and manufacture :
13.67.1 Two or more coats of glue sizing with copal varnish over an under coat of flatting
varnish
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0856 Ordinary varnish litre 0.70 100.00 70.00
0763 Glue kilogram 0.07 75.00 5.25
0857 Superior copal varnish litre 1.16 115.00 133.40
9977 Carriage L.S. 1.43 2.12 3.03
9999 Putty for repair to holes etc L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.90 714.00 642.60
(0.36+0.54=0.90)
0115 Coolie day 0.90 645.00 580.50
(0.36+0.54=0.90)
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 1475.57 W
Add 1 % Water charges on "W" 14.76
TOTAL 1490.33 X
Add GST on "X" (multiplying
factor 0.1405) 209.39
TOTAL 1699.72 Y
Add 15% CPOH on "Y" 254.96
TOTAL 1954.67 Z
Add Cess @ 1% on "Z" 19.55
Cost of 10.00 sqm 1974.22
Cost of 1.00 sqm 197.42
Say 197.40
13.67.2 Two or more coats glue sizing with spar varnish or an under coat of flatting
varnish
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0856 Ordinary varnish litre 0.70 100.00 70.00
0763 Glue kilogram 0.07 75.00 5.25
0858 Superior spar varnish litre 1.26 115.00 144.90
9977 Carriage L.S. 1.43 2.12 3.03
9999 Repair etc L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.90 714.00 642.60
(0.36+0.54=0.90)
0115 Coolie day 0.90 645.00 580.50
(0.36+0.54=0.90)
9999 Brushes, sand paper etc L.S. 6.76 2.12 14.33
SUB HEAD : 13- FINISHING 1050
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 1481.56 W
Add 1 % Water charges on "W" 14.82
TOTAL 1496.37 X
Add GST on "X" (multiplying
factor 0.1405) 210.24
TOTAL 1706.61 Y
Add 15% CPOH on "Y" 255.99
TOTAL 1962.61 Z
Add Cess @ 1% on "Z" 19.63
Cost of 10.00 sqm 1982.23
Cost of 1.00 sqm 198.22
Say 198.20
13.68 French spirit polishing :
13.68.1 Two or more coats on new works including a coat of wood filler
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
1000 Spirit litre 1.63 48.00 78.24
9999 Pigment L.S. 7.15 2.12 15.16
0999 Shellac kilogram 0.24 300.00 72.00
9977 Carriage of material L.S. 2.73 2.12 5.79
9999 White woolen cloth, putty L.S. 16.12 2.12 34.17
9999 Sand paper cotton etc L.S. 13.39 2.12 28.39
9999 Lineseed oil L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 3.50 714.00 2499.00
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 2752.87 W
Add 1 % Water charges on "W" 27.53
TOTAL 2780.39 X
Add GST on "X" (multiplying
factor 0.1405) 390.65
TOTAL 3171.04 Y
Add 15% CPOH on "Y" 475.66
TOTAL 3646.70 Z
Add Cess @ 1% on "Z" 36.47
Cost of 10.00 sqm 3683.16
Cost of 1.00 sqm 368.32
Say 368.30
13.69 Polishing on wood work with ready mixed wax polish of approved brand and
manufacture :
13.69.1 New work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0855 Wax polish (ready made) kilogram 0.50 230.00 115.00
SUB HEAD : 13- FINISHING 1051
Code Description Unit Quantity Rate Amount
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.80 714.00 571.20
0115 Coolie day 0.80 645.00 516.00
9999 Soap, brushes, cloth etc L.S. 4.16 2.12 8.82
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 1227.00 W
Add 1 % Water charges on "W" 12.27
TOTAL 1239.27 X
Add GST on "X" (multiplying
factor 0.1405) 174.12
TOTAL 1413.39 Y
Add 15% CPOH on "Y" 212.01
TOTAL 1625.40 Z
Add Cess @ 1% on "Z" 16.25
Cost of 10.00 sqm 1641.65
Cost of 1.00 sqm 164.17
Say 164.15
13.70 Floor polishing on masonry or concrete floors with wax polish of approved
brand and manufacture.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0855 Wax polish (ready made) kilogram 0.10 230.00 23.00
LABOUR
0131 Painter day 0.40 714.00 285.60
0115 Coolie day 0.40 645.00 258.00
9999 Acetic acid soap, cloth etc L.S. 5.33 2.12 11.30
9988 Sundries including Carriage L.S. 8.06 2.12 17.09
TOTAL 594.99 W
Add 1 % Water charges on "W" 5.95
TOTAL 600.94 X
Add GST on "X" (multiplying
factor 0.1405) 84.43
TOTAL 685.37 Y
Add 15% CPOH on "Y" 102.81
TOTAL 788.17 Z
Add Cess @ 1% on "Z" 7.88
Cost of 10.00 sqm 796.06
Cost of 1.00 sqm 79.61
Say 79.60
13.71 Lettering with black Japan paint of approved brand and manufacture
Code Description Unit Quantity Rate Amount
Detail of cost for 100 letters of
15 cm height
MATERIAL
0829 Black Japan paint litre 0.56 90.00 50.40
SUB HEAD : 13- FINISHING 1052
Code Description Unit Quantity Rate Amount
9977 Carriage L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 6.00 714.00 4284.00
0115 Coolie day 2.00 645.00 1290.00
9999 Painting brushes, turpentine, stencil etc L.S. 13.39 2.12 28.39
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 5671.80 W
Add 1 % Water charges on "W" 56.72
TOTAL 5728.52 X
Add GST on "X" (multiplying
factor 0.1405) 804.86
TOTAL 6533.38 Y
Add 15% CPOH on "Y" 980.01
TOTAL 7513.39 Z
Add Cess @ 1% on "Z" 75.13
Cost of 100 letters of 15 cm height 7588.52
Cost of 1 letters of 1 cm height 5.06
Say 5.05
13.72 Washed stone grit plaster on exterior walls height upto 10 metre above ground
level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse
sand ), furrowing the under layer with scratching tool, applying cement slurry
on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement
plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal
size), in panels with groove all around as per approved pattern, including
scrubbing and washing the top layer with brushes and water to expose the
stone chippings ,complete as per specification and direction of Engineer-in-
charge (payment for providing grooves shall be made separately).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Under layer 12 mm cement plaster with
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.144 4355.20 627.15
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0114 Beldar day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding L.S. 8.97 2.12 19.02
Applying cement slurry
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
0114 Beldar day 0.25 645.00 161.25
Top layer 15 mm thick stone chipping
plaster Quantity required = 0.172 cum
including wastage
Preparation of cement concrete
mix 1:1/2:2
(1 cement : 1/2 coarse sand : 2 stone
chipping 10 mm nominal size)
SUB HEAD : 13- FINISHING 1053
Code Description Unit Quantity Rate Amount
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.14 1200.00 168.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.14 163.93 22.95
0982 Coarse sand (zone III) cum 0.04 1500.00 60.00
2203 Carriage of Coarse sand cum 0.04 163.93 6.56
0367 Portland Cement (OPC-43 grade) tonne 0.10 5000.00 500.00
2209 Carriage of Cement tonne 0.10 145.72 14.57
0114 Beldar day 0.10 645.00 64.50
0101 Bhisti day 0.05 714.00 35.70
9999 Hire and running charges of
mechanical mixer L.S. 4.29 2.12 9.09
9999 Sundries L.S. 2.08 2.12 4.41
LABOUR
0123 Mason (brick layer) 1st class Day 1.75 784.00 1372.00
0114 Beldar Day 1.75 645.00 1128.75
0101 Bhisti Day 0.30 714.00 214.20
9999 Scaffolding L.S. 24.44 2.12 51.81
Labour for washing
0123 Mason (brick layer) 1st class Day 1.00 784.00 784.00
0115 Coolie Day 0.50 645.00 322.50
9999 Sundries soft brushes etc L.S. 25.22 2.12 53.47
TOTAL 7365.30 W
Add 1 % Water charges on "W" 73.65
TOTAL 7438.96 X
Add GST on "X" (multiplying
factor 0.1405) 1045.17
TOTAL 8484.13 Y
Add 15% CPOH on "Y" 1272.62
TOTAL 9756.75 Z
Add Cess @ 1% on "Z" 97.57
Cost of 10.00 sqm 9854.32
Cost of 1.00 sqm 985.43
Say 985.45
13.73 Forming groove of uniform size in the top layer of washed stone grit plaster
as per approved pattern using wooden battens, nailed to the under layer,
including removal of wooden battens, repair to the edges of panels and
finishing the groove complete as per specifications and direction of the
Engineer-in-charge :
13.73.1 15 mm wide and 15 mm deep groove
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Second class kail wood in plank
30 x0.015 x0.015m =6.75cudm
Wastage @ 10% = 0.68
Total = 7.43 cudm
Assuming that the battens shall
become unserviceable after using 5
times
Cost for using once = 7.43 / 5 =
1.48 cudm
SUB HEAD : 13- FINISHING 1054
Code Description Unit Quantity Rate Amount
MATERIAL
1198 Second class kail wood in planks 10 cudm 0.148 260.00 38.48
9977 Carriage of wood L.S. 0.39 2.12 0.83
Labour for making battens
0112 Carpenter 2nd class day 0.15 714.00 107.10
0114 Beldar day 0.15 645.00 96.75
9999 Sundries L.S. 2.86 2.12 6.06
Labour for nailing the battens to under
layer and finishing and repairing
grooves
0123 Mason (brick layer) 1st class day 0.70 784.00 548.80
0114 Beldar day 0.70 645.00 451.50
9999 Nails and cement mortar L.S. 71.76 2.12 152.13
TOTAL 1401.65 W
Add 1 % Water charges on "W" 14.02
TOTAL 1415.67 X
Add GST on "X" (multiplying
factor 0.1405) 198.90
TOTAL 1614.57 Y
Add 15% CPOH on "Y" 242.19
TOTAL 1856.75 Z
Add Cess @ 1% on "Z" 18.57
Cost of 30.00 mtrs 1875.32
Cost of 1.00 metre 62.51
Say 62.50
13.73.2 20 mm wide and 15 mm deep groove
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Second class kail wood in plank
30 x0.02 x0.015m =9.00 cudm
Wastage @ 10% = 0.90
Total = 9.90 cudm
Assuming that the battens shall
become unserviceable after using 5
times
Cost for using once = 9.9 / 5
= 1.98 cudm
MATERIAL
1198 Second class kail wood in planks 10 cudm 0.198 260.00 51.48
9977 Carriage of wood L.S. 0.52 2.12 1.10
Labour for making battens
0112 Carpenter 2nd class day 0.15 714.00 107.10
0114 Beldar day 0.15 645.00 96.75
9999 Sundries L.S. 2.86 2.12 6.06
Labour for nailing the battens to under
layer and finishing and repairing
grooves
0123 Mason (brick layer) 1st class day 0.70 784.00 548.80
0114 Beldar day 0.70 645.00 451.50
SUB HEAD : 13- FINISHING 1055
Code Description Unit Quantity Rate Amount
9999 Nails and cement mortar L.S. 71.76 2.12 152.13
TOTAL 1414.93 W
Add 1 % Water charges on "W" 14.15
TOTAL 1429.08 X
Add GST on "X" (multiplying
factor 0.1405) 200.79
TOTAL 1629.86 Y
Add 15% CPOH on "Y" 244.48
TOTAL 1874.34 Z
Add Cess @ 1% on "Z" 18.74
Cost of 30.00 mtrs 1893.08
Cost of 1.00 metre 63.10
Say 63.10
13.74 Extra for washed grit plaster on exterior walls of height more than 10 m from
ground level for every additional height of 3 m or part thereof.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
9999 Scaffolding L.S. 215.28 2.12 456.39
0123 Mason (brick layer) 1st class day 0.30 784.00 235.20
0114 Beldar day 0.30 645.00 193.50
0101 Bhisti day 0.15 714.00 107.10
9999 Sundries L.S. 28.60 2.12 60.63
TOTAL 1052.83 W
Add 1 % Water charges on “W” 10.53
TOTAL 1063.35 X
Add GST on “X” (multiplying
factor 0.1405) 149.40
TOTAL 1212.76 Y
Add 15% CPOH on “Y” 181.91
TOTAL 1394.67 Z
Add Cess @ 1% on “Z” 13.95
Cost of 10.00 sqm 1408.62
Cost of 1.00 sqm 140.86
Say 140.85
13.75 Extra for washed stone grit plaster on circular work not exceeding 6 m in
radius (in two coats).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
SUB HEAD : 13- FINISHING 1056
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 53.82 2.12 114.10
TOTAL 828.60 W
Add 1 % Water charges on "W" 8.29
TOTAL 836.88 X
Add GST on "X" (multiplying
factor 0.1405) 117.58
TOTAL 954.47 Y
Add 15% CPOH on "Y" 143.17
TOTAL 1097.64 Z
Add Cess @ 1% on "Z" 10.98
Cost of 10.00 sqm 1108.61
Cost of 1.00 sqm 110.86
Say 110.85
13.76 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top
layer of washed stone grit plastered surface as per approved pattern, including
providing and fixing aluminum channels of appropriate size and thickness
(not less than 2 mm), nailed to the under layer with rust proof screws and
nails and finishing the groove complete as per specifications and direction of
the Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 30 mtrs
Aluminium channel section 15 x 15 x
2 mm (weight 0.221 kg/mtr)
Qty = 30 + 5% wastage =
31.5 m @ 0.221
kg/m = 6.96 kg.
7306 Aluminium T or L sections kilogram 6.96 190.00 1322.40
9977 Carriage L.S. 38.98 2.12 82.64
Labour for fixing
0117 Assistant Fitter or 2nd class Fitter day 0.46 714.00 328.44
0114 Beldar day 0.15 645.00 96.75
9999 Sundries L.S. 2.86 2.12 6.06
9999 Nails and cement mortar L.S. 71.76 2.12 152.13
TOTAL 1988.42 W
Add 1 % Water charges on "W" 19.88
TOTAL 2008.31 X
Add GST on "X" (multiplying
factor 0.1405) 282.17
TOTAL 2290.47 Y
Add 15% CPOH on "Y" 343.57
TOTAL 2634.04 Z
Add Cess @ 1% on "Z" 26.34
Cost of 30.00 mtrs 2660.38
Cost of 1.00 metre 88.68
Say 88.70
SUB HEAD : 13- FINISHING 1057
13.77 Extra for using white cement in place of ordinary cement in the top layer of
the item of washed stone grit plaster.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Add for
0368 White Cement tonne 0.10 11200.00 1120.00
Deduct for ordinary cement
0367 Portland Cement (OPC-43 grade) tonne -0.10 5000.00 -500.00
TOTAL 620.00 W
Add 1 % Water charges on "W" 6.20
TOTAL 626.20 X
Add GST on "X" (multiplying
factor 0.1405) 87.98
TOTAL 714.18 Y
Add 15% CPOH on "Y" 107.13
TOTAL 821.31 Z
Add Cess @ 1% on "Z" 8.21
Cost of 10.00 sqm 829.52
Cost of 1.00 sqm 82.95
Say 82.95
13.78 Providing and applying 12 mm thick (average) premixed formulated one coat
gypsum lightweight plaster having additives and light weight aggregates as
vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976,
applied on hacked / uneven background such as bare brick/ block/ RCC work
on walls & ceiling at all floors and locations, finished in smooth line and level
etc. complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Premixed super white gypsum plaster
@ 16.14kg /sqm = 61.40 + 5%
wastage = 161.40+8.07= 169.47 kg
0868 Premixed super white gypsum plaster. kg 169.47 6.00 1016.82
LABOUR
0155 Mason (average) day 1.20 749.00 898.80
0115 Coolie day 1.20 645.00 774.00
SUB HEAD : 13- FINISHING 1058
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2716.35 W
Add 1 % Water charges on "W" 27.16
TOTAL 2743.52 X
Add GST on "X" (multiplying
factor 0.1405) 385.46
TOTAL 3128.98 Y
Add 15% CPOH on "Y" 469.35
TOTAL 3598.33 Z
Add Cess @ 1% on "Z" 35.98
Cost of 10.00 sqm 3634.31
Cost of 1.00 sqm 363.43
Say 363.45
13.79 Extra for addition of synthetic Polyester triangular fibre of length 6 mm, effective
diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement plaster/
mortar by using 125 gms. of synthetic Polyester triangular fibre for 50 Kgs.
cement used in cement mortar as per directions of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for per bag of 50 kg of
cement used in mortar
MATERIAL
8733 Synthetic ployster triangular fibre of
length 6 mm, effective diameter 10-40
microns and specific gravity of 1.34 to
1.40 including labour for mixing kg 0.125 410.00 51.25
TOTAL 51.25 W
Add 1 % Water charges on "W" 0.51
TOTAL 51.76 X
Add GST on "X" (multiplying
factor 0.1405) 7.27
TOTAL 59.04 Y
Add 15% CPOH on "Y" 8.86
TOTAL 67.89 Z
Add Cess @ 1% on "Z" 0.68
Cost per bag of cement 68.57
Say 68.55
SUB HEAD : 13- FINISHING 1059
13.80 Providing and applying white cement based putty of average thickness 1 mm,
of approved brand and manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0824 Cement base wall care putty kg 14.58 13.00 189.54
10x0.001x1429 = 14.29kg
Add 2% wastage= 0.29kg
Total = 14.58kg Say 14.58 kg
9977 Carriage L.S. 3.90 2.12 8.27
LABOUR
0122 Mason (for plaster of paris work)
1st class day 0.45 784.00 352.80
0114 Beldar day 0.45 645.00 290.25
9999 Scaffolding and sundries L.S. 40.00 2.12 84.80
TOTAL 925.66 W
Add 1 % Water charges on "W" 9.26
TOTAL 934.91 X
Add GST on "X" (multiplying
factor 0.1405) 131.36
TOTAL 1066.27 Y
Add 15% CPOH on "Y" 159.94
TOTAL 1226.21 Z
Add Cess @ 1% on "Z" 12.26
Cost of 10.00 sqm 1238.47
Cost of 1.00 sqm 123.85
Say 123.85
13.81 Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic
Compound ) content less than 50 grams/ litre, of approved brand and
manufacture, including applying additional coats wherever required, to
achieve even shade and colour.
13.81.1 One coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0802 Acrylic distemper 1st quality , having
VOC content less than 50 gm/kg Kg 0.62 40.00 24.80
9999 Brushes, putty etc. L.S. 0.52 2.12 1.10
9988 Sundries including carriage L.S. 10.79 2.12 22.87
SUB HEAD : 13- FINISHING 1060
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.33 714.00 235.62
0115 Coolie day 0.17 645.00 109.65
9999 Scaffolding and sundries L.S. 7.15 2.12 15.16
TOTAL 409.21 W
Add 1 % Water charges on "W" 4.09
TOTAL 413.30 X
Add GST on "X" (multiplying
factor 0.1405) 58.07
TOTAL 471.37 Y
Add 15% CPOH on "Y" 70.70
TOTAL 542.07 Z
Add Cess @ 1% on "Z" 5.42
Cost of 10.00 sqm 547.49
Cost of 1.00 sqm 54.75
Say 54.75
13.81.2 Two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0802 Acrylic distemper 1st quality, having
VOC content less than 50 gm/kg Kg 0.99 40.00 39.60
9999 Brushes, putty etc. L.S. 11.57 2.12 24.53
9988 Sundries including carriage L.S. 4.42 2.12 9.37
LABOUR
0131 Painter day 0.40 714.00 285.60
0115 Coolie day 0.46 645.00 296.70
9999 Scaffolding and sundries L.S. 8.06 2.12 17.09
TOTAL 672.89 W
Add 1 % Water charges on "W" 6.73
TOTAL 679.61 X
Add GST on "X" (multiplying
factor 0.1405) 95.49
TOTAL 775.10 Y
Add 15% CPOH on "Y" 116.27
TOTAL 891.37 Z
Add Cess @ 1% on "Z" 8.91
Cost of 10.00 sqm 900.28
Cost of 1.00 sqm 90.03
Say 90.05
SUB HEAD : 13- FINISHING 1061
13.82 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic
Compound ) content less than 50 grams/ litre, of approved brand and
manufacture, including applying additional coats wherever required, to
achieve even shade and colour.
13.82.1 One coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0803 Acrylic emulsion , having VOC content
less than 50 gm/ltr litre 0.53 94.00 49.82
9999 For filling holes and cracks with putty etc L.S. 0.52 2.12 1.10
9977 Carriage of material L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc. L.S. 8.06 2.12 17.09
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 582.88 W
Add 1 % Water charges on "W" 5.83
TOTAL 588.71 X
Add GST on "X" (multiplying
factor 0.1405) 82.71
TOTAL 671.42 Y
Add 15% CPOH on "Y" 100.71
TOTAL 772.14 Z
Add Cess @ 1% on "Z" 7.72
Cost of 10.00 sqm 779.86
Cost of 1.00 sqm 77.99
Say 78.00
13.82.2 Two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0803 Acrylic emulsion , having VOC content
less than 50 gm/ltr litre 0.84 94.00 78.96
9999 For filling holes and cracks with putty etc L.S. 1.43 2.12 3.03
9977 Carriage of material L.S. 6.76 2.12 14.33
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc. L.S. 10.79 2.12 22.87
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 867.39 W
Add 1 % Water charges on "W" 8.67
TOTAL 876.06 X
Add GST on "X" (multiplying
factor 0.1405) 123.09
TOTAL 999.15 Y
Add 15% CPOH on "Y" 149.87
TOTAL 1149.02 Z
Add Cess @ 1% on "Z" 11.49
Cost of 10.00 sqm 1160.51
Cost of 1.00 sqm 116.05
Say 116.05
SUB HEAD : 13- FINISHING 1062
13.83 Wall painting with premium acrylic emulsion paint of interior grade, having
VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved
brand and manufacture, including applying additional coats wherever required
to achieve even shade and colour.
13.83.1 One coat
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0804 Premium acrylic emulsion of interior
grade, having VOC content less than
50 gm/ltr. litre 0.38 200.00 76.00
9999 For filling holes and cracks with putty etc L.S. 0.52 2.12 1.10
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc. L.S. 8.06 2.12 17.09
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 599.69 W
Add 1 % Water charges on "W" 6.00
TOTAL 605.69 X
Add GST on "X" (multiplying
factor 0.1405) 85.10
TOTAL 690.79 Y
Add 15% CPOH on "Y" 103.62
TOTAL 794.40 Z
Add Cess @ 1% on "Z" 7.94
Cost of 10.00 sqm 802.35
Cost of 1.00 sqm 80.23
Say 80.25
13.83.2 Two coats
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0804 Premium acrylic emulsion of interior
grade, having VOC content less than
50 gm/ltr. litre 0.60 200.00 120.00
9999 For filling holes and cracks with putty etc L.S. 1.43 2.12 3.03
9977 Carriage of material L.S. 6.76 2.12 14.33
LABOUR
0131 Painter day 0.54 714.00 385.56
0115 Coolie day 0.54 645.00 348.30
9999 Brushes, sand paper etc. L.S. 10.79 2.12 22.87
SUB HEAD : 13- FINISHING 1063
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 908.43 W
Add 1 % Water charges on "W" 9.08
TOTAL 917.51 X
Add GST on "X" (multiplying
factor 0.1405) 128.91
TOTAL 1046.42 Y
Add 15% CPOH on "Y" 156.96
TOTAL 1203.39 Z
Add Cess @ 1% on "Z" 12.03
Cost of 10.00 sqm 1215.42
Cost of 1.00 sqm 121.54
Say 121.55
13.85 Applying priming coats with primer of approved brand and manufacture,
having low VOC (Volatile Organic Compound ) content.
13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood)
having VOC content less than 50 grams/ litre
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0806 Ready mixed pink or grey primer on
wood work (hard and soft wood) having
VOC content less than 50 gms/lit. litre 0.75 105.00 78.75
9999 Putty L.S. 2.73 2.12 5.79
9977 Carriage of material L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
9999 Brushes, sand paper etc. L.S. 5.33 2.12 11.30
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 459.29 W
Add 1 % Water charges on "W" 4.59
TOTAL 463.88 X
Add GST on "X" (multiplying
factor 0.1405) 65.18
TOTAL 529.06 Y
Add 15% CPOH on "Y" 79.36
TOTAL 608.42 Z
Add Cess @ 1% on "Z" 6.08
Cost of 10.00 sqm 614.50
Cost of 1.00 sqm 61.45
Say 61.45
SUB HEAD : 13- FINISHING 1064
13.85.3 With water thinnable cement primer on wall surface having VOC content less
than 50 grams/litre
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0808 Water thinnable cement primer for
interior wall surface, having VOC
content less than 50 gms/lit. litre 0.70 50.00 35.00
9977 Carriage of material L.S. 8.06 2.12 17.09
LABOUR
0131 Painter day 0.40 714.00 285.60
0115 Coolie day 0.20 645.00 129.00
9999 Brushes, sand paper etc. L.S. 7.15 2.12 15.16
TOTAL 481.85 W
Add 1 % Water charges on "W" 4.82
TOTAL 486.66 X
Add GST on "X" (multiplying
factor 0.1405) 68.38
TOTAL 555.04 Y
Add 15% CPOH on "Y" 83.26
TOTAL 638.30 Z
Add Cess @ 1% on "Z" 6.38
Cost of 10.00 sqm 644.68
Cost of 1.00 sqm 64.47
Say 64.45
13.86 6 mm plaster on cement concrete or reinforced cement concrete work with
white cement based polymer modified self curing mortar of approved make
as per the direction of Engineer-In-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0772 White cement based polymer modified
self curing compound in powder form kg 46.00 15.00 690.00
i/c 2% wastage
9977 Carriage of white cement based
polymer modified self curing compound
in powder form L.S. 7.80 2.12 16.54
LABOUR
0155 Mason (average) day 0.51 749.00 381.99
0115 Coolie day 0.75 645.00 483.75
9999 Extra for removing burrs, cleaning with
wire brushes and pock making with
pointed tools etc. L.S. 13.39 2.12 28.39
SUB HEAD : 13- FINISHING 1065
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sunderies L.S. 11.70 2.12 24.80
TOTAL 1625.47 W
Add 1 % Water charges on "W" 16.25
TOTAL 1641.72 X
Add GST on "X" (multiplying
factor 0.1405) 230.66
TOTAL 1872.38 Y
Add 15% CPOH on "Y" 280.86
TOTAL 2153.24 Z
Add Cess @ 1% on "Z" 21.53
Cost of 10 sqm 2174.77
Cost of 1 sqm 217.48
Say 217.50
13.87 White washing with lime to give an even shade :
13.87.1 Old work (two or more coats)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0775 Dehradun white lime quintal 0.02 600.00 12.00
9977 Carriage of lime L.S. 0.52 2.12 1.10
LABOUR
0141 White Washer day 0.11 714.00 78.54
0115 Coolie day 0.06 645.00 38.70
9999 Indigo gum etc L.S. 2.73 2.12 5.79
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 141.92 W
Add 1 % Water charges on "W" 1.42
TOTAL 143.34 X
Add GST on "X" (multiplying
factor 0.1405) 20.14
TOTAL 163.48 Y
Add 15% CPOH on "Y" 24.52
TOTAL 188.00 Z
Add Cess @ 1% on "Z" 1.88
Cost of 10.00 sqm 189.88
Cost of 1.00 sqm 18.99
Say 19.00
13.87.2 Old work (one or more coats)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0775 Dehradun white lime quintal 0.01 600.00 6.00
9977 Carriage of lime L.S. 0.52 2.12 1.10
LABOUR
0141 White Washer day 0.07 714.00 49.98
0115 Coolie day 0.03 645.00 19.35
9999 Indigo gum etc L.S. 2.08 2.12 4.41
SUB HEAD : 13- FINISHING 1066
Code Description Unit Quantity Rate Amount
9999 Sundries ladders etc L.S. 2.73 2.12 5.79
TOTAL 86.63 W
Add 1 % Water charges on "W" 0.87
TOTAL 87.50 X
Add GST on "X" (multiplying
factor 0.1405) 12.29
TOTAL 99.79 Y
Add 15% CPOH on "Y" 14.97
TOTAL 114.76 Z
Add Cess @ 1% on "Z" 1.15
Cost of 10.00 sqm 115.91
Cost of 1.00 sqm 11.59
Say 11.60
13.88 Removing white or colour wash by scrapping and sand papering and preparing
the surface smooth including necessary repairs to scratches etc. complete
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
LABOUR
0114 Beldar day 0.09 645.00 58.05
0115 Coolie day 0.04 645.00 25.80
0101 Bhisti day 0.04 714.00 28.56
9999 Sundries such as sand paper and
scrapper L.S. 2.73 2.12 5.79
9999 Repair to scraches L.S. 1.82 2.12 3.86
TOTAL 122.06 W
Add 1 % Water charges on "W" 1.22
TOTAL 123.28 X
Add GST on "X" (multiplying
factor 0.1405) 17.32
TOTAL 140.60 Y
Add 15% CPOH on "Y" 21.09
TOTAL 161.69 Z
Add Cess @ 1% on "Z" 1.62
Cost of 10 sqm. 163.30
Cost of 1 sqm. 16.33
Say 16.35
13.90 Distempering with 1st quality acrylic distember (Ready mix) having VOC
content less than 50 grams/ litre of approved brand and manufacture to give
an even shade :
13.90.1 Old work (one or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
0802 Acrylic distemper 1st quality , having
VOC content less than 50 grams/ litre kilogram 1.00 40.00 40.00
9999 Brushes, putty etc. L.S. 0.52 2.12 1.10
9988 Sundries including carriage L.S. 10.79 2.12 22.87
SUB HEAD : 13- FINISHING 1067
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.33 714.00 235.62
0115 Coolie day 0.17 645.00 109.65
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 424.41 W
Add 1 % Water charges on "W" 4.24
TOTAL 428.65 X
Add GST on "X" (multiplying
factor 0.1405) 60.23
TOTAL 488.87 Y
Add 15% CPOH on "Y" 73.33
TOTAL 562.21 Z
Add Cess @ 1% on "Z" 5.62
Cost of 10 sqm. 567.83
Cost of 1 sqm. 56.78
Say 56.80
13.91 Removing dry or oil bound distemper, water proofing cement paint and the
like by scrapping, sand papering and preparing the surface smooth including
necessary repairs to scratches etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
LABOUR
0114 Beldar day 0.11 645.00 70.95
0115 Coolie day 0.05 645.00 32.25
0101 Bhisti day 0.05 714.00 35.70
9999 Scrapper, sand paper etc. L.S. 6.24 2.12 13.23
9999 Sundries including mortar to repair the
surface L.S. 1.82 2.12 3.86
TOTAL 155.99 W
Add 1 % Water charges on "W" 1.56
TOTAL 157.55 X
Add GST on "X" (multiplying
factor 0.1405) 22.14
TOTAL 179.68 Y
Add 15% CPOH on "Y" 26.95
TOTAL 206.63 Z
Add Cess @ 1% on "Z" 2.07
Cost of 10 sqm. 208.70
Cost of 1 sqm. 20.87
Say 20.85
13.92 Painting on G.S. sheet with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade :
13.92.1 Old work (one or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
0845 Roofing paint for iron sheets in red colour litre 0.46 120.00 55.20
SUB HEAD : 13- FINISHING 1068
Code Description Unit Quantity Rate Amount
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Putty, brushes sand paper etc. L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 576.96 W
Add 1 % Water charges on "W" 5.77
TOTAL 582.73 X
Add GST on "X" (multiplying
factor 0.1405) 81.87
TOTAL 664.60 Y
Add 15% CPOH on "Y" 99.69
TOTAL 764.29 Z
Add Cess @ 1% on "Z" 7.64
Cost of 10 sqm. 771.94
Cost of 1 sqm. 77.19
Say 77.20
13.93 Painting (two or more coats) on rain water, soil, waste and vent pipes and
fittings with black anticorrosive bitumastic paint of approved brand and
manufacture over and including a priming coat of ready mixed zinc chromate
yellow primer on new work :
13.93.1 75 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 metres
Area=22/7 x0.0814m x30m =7.67 sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.41 120.00 49.20
9977 Carraige L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.18 714.00 128.52
0115 Coolie day 0.18 645.00 116.10
9999 Brushes, sand paper etc L.S. 8.19 2.12 17.36
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.73 100.00 73.00
9977 Carraige L.S. 1.04 2.12 2.20
LABOUR
0131 Painter day 0.41 714.00 292.74
0115 Coolie day 0.41 645.00 264.45
9999 Putty, sand paper etc L.S. 4.16 2.12 8.82
9999 Sundries L.S. 6.24 2.12 13.23
9999 Wire brushes for cleaning L.S. 4.42 2.12 9.37
9999 Extra for delays L.S. 40.3 2.12 85.44
TOTAL 1061.26 W
Add 1 % Water charges on "W" 10.61
TOTAL 1071.87 X
Add GST on "X" (multiplying
factor 0.1405) 150.60
TOTAL 1222.47 Y
Add 15% CPOH on "Y" 183.37
TOTAL 1405.84 Z
Add Cess @ 1% on "Z" 14.06
Cost of 30.00 metres 1419.90
Cost of 1.00 metre 47.33
Say 47.35
SUB HEAD : 13- FINISHING 1069
13.94 Painting (one or more coats) on rain water, soil waste and vent pipes and
fittings with black anticorrosive bitumastic paint of approved brand and
manufacture on old work :
13.94.1 75 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 metres
Area=22/7 x0.0814m x30m =7.67 sqm
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.43 100.00 43.00
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.27 714.00 192.78
0115 Coolie day 0.27 645.00 174.15
9999 Putty, sand paper etc L.S. 4.16 2.12 8.82
9999 Sundries L.S. 6.24 2.12 13.23
9999 Wire brushes for cleaning L.S. 4.42 2.12 9.37
9999 Extra for delays L.S. 26.91 2.12 57.05
TOTAL 499.22 W
Add 1 % Water charges on "W" 4.99
TOTAL 504.22 X
Add GST on "X" (multiplying
factor 0.1405) 70.84
TOTAL 575.06 Y
Add 15% CPOH on "Y" 86.26
TOTAL 661.32 Z
Add Cess @ 1% on "Z" 6.61
Cost of 30.00 metres 667.93
Cost of 1.00 metre 22.26
Say 22.25
13.94.2 100 mm diameter pipes
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres
Area = 22/7x106.4 mmx30 m
= 10.032 sqm
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.57 100.00 57.00
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Putty, sand paper brushes etc. L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
9999 Wire brushes for cleaning L.S. 5.33 2.12 11.30
SUB HEAD : 13- FINISHING 1070
Code Description Unit Quantity Rate Amount
9999 Extra for delay L.S. 34.06 2.12 72.21
TOTAL 659.24 W
Add 1 % Water charges on "W" 6.59
TOTAL 665.83 X
Add GST on "X" (multiplying
factor 0.1405) 93.55
TOTAL 759.38 Y
Add 15% CPOH on "Y" 113.91
TOTAL 873.28 Z
Add Cess @ 1% on "Z" 8.73
Cost of 30.00 metres 882.02
Cost of 1.00 metre 29.40
Say 29.40
13.94.3 150 mm diameter pipes
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres
Area = 22/7x157.2 mmx30 m
= 14.82 sqm
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.85 100.00 85.00
9977 Carriage L.S. 0.65 2.12 1.38
LABOUR
0131 Painter day 0.53 714.00 378.42
0115 Coolie day 0.53 645.00 341.85
9999 Putty, sand paper brushes etc. L.S. 8.06 2.12 17.09
9999 Sundries L.S. 11.96 2.12 25.36
9999 Wire brushes for cleaning L.S. 7.14 2.12 15.14
9999 Extra for delay L.S. 40.30 2.12 85.44
TOTAL 949.66 W
Add 1 % Water charges on "W" 9.50
TOTAL 959.16 X
Add GST on "X" (multiplying
factor 0.1405) 134.76
TOTAL 1093.92 Y
Add 15% CPOH on "Y" 164.09
TOTAL 1258.01 Z
Add Cess @ 1% on "Z" 12.58
Cost of 30.00 metres 1270.59
Cost of 1.00 metre 42.35
Say 42.35
13.95 Painting (two or more coats) on rain water, soil waste and vent pipes and
fittings with aluminium paint of approved brand and manufacture over a priming
coat of ready mixed zinc chromate yellow primer on new work :
13.95.1 75 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 metres
Area=22/7 x0.0814m x30m =7.67 sqm
SUB HEAD : 13- FINISHING 1071
Code Description Unit Quantity Rate Amount
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.41 120.00 49.20
9977 Carriage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.18 714.00 128.52
0115 Coolie day 0.18 645.00 116.10
9999 Sundries L.S. 8.19 2.12 17.36
MATERIAL
0826 Aluminium paint litre 0.61 150.00 91.50
9977 Carriage L.S. 1.04 2.12 2.20
9999 Putty, sand paper etc L.S. 4.16 2.12 8.82
LABOUR
0131 Painter day 0.41 714.00 292.74
0115 Coolie day 0.41 645.00 264.45
9999 Sundries L.S. 5.20 2.12 11.02
9999 Wire brushes for cleaning L.S. 9.10 2.12 19.29
9999 Extra for delays L.S. 44.85 2.12 95.08
TOTAL 1097.12 W
Add 1 % Water charges on "W" 10.97
TOTAL 1108.09 X
Add GST on "X" (multiplying
factor 0.1405) 155.69
TOTAL 1263.78 Y
Add 15% CPOH on "Y" 189.57
TOTAL 1453.35 Z
Add Cess @ 1% on "Z" 14.53
Cost of 30.00 metres 1467.88
Cost of 1.00 metre 48.93
Say 48.95
13.95.2 100 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 metres
Area=22/7 x106.4x30m =10.032sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.54 120.00 64.80
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.24 714.00 171.36
0.18 x 10.032 / 7.67 = 0.24
0115 Coolie day 0.24 645.00 154.80
9999 Sundries L.S. 10.79 2.12 22.87
MATERIAL
0826 Aluminium paint litre 1.16 150.00 174.00
0.61 x 10.032 / 7.67 = 0.80
9977 Carriage L.S. 1.43 2.12 3.03
9999 Putty, sand paper etc L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.54 714.00 385.56
0.41 x 10.032 / 7.67 = 0.54
0115 Coolie day 0.54 645.00 348.30
9999 Sundries L.S. 6.76 2.12 14.33
SUB HEAD : 13- FINISHING 1072
Code Description Unit Quantity Rate Amount
9999 Wire brushes for cleaning L.S. 11.96 2.12 25.36
9999 Extra for delays L.S. 66.43 2.12 140.83
TOTAL 1517.65 W
Add 1 % Water charges on "W" 15.18
TOTAL 1532.82 X
Add GST on "X" (multiplying
factor 0.1405) 215.36
TOTAL 1748.18 Y
Add 15% CPOH on "Y" 262.23
TOTAL 2010.41 Z
Add Cess @ 1% on "Z" 20.10
Cost of 30.00 metres 2030.52
Cost of 1.00 metre 67.68
Say 67.70
13.95.3 150 mm diameter pipes
Code Description Unit Quantity Rate Amount
Detail of cost for 30 metres
Area=22/7 x157.12x30m =14.82 sqm
MATERIAL
4202 Red oxide Zinc chromate primer litre 0.80 120.00 96.00
9977 Carriage L.S. 0.65 2.12 1.38
LABOUR
0131 Painter Day 0.36 714.00 257.04
0.18 x 14.82 / 7.67 = 0.36
0115 Coolie Day 0.36 645.00 232.20
9999 Sundries L.S. 15.99 2.12 33.90
MATERIAL
0826 Aluminium paint litre 1.72 150.00 258.00
0.61 x 14.82 / 7.67 = 1.72
9977 Carriage L.S. 2.08 2.12 4.41
9999 Putty, sand paper etc L.S. 7.93 2.12 16.81
LABOUR
0131 Painter day 0.80 714.00 571.20
0.41 x 14.82 / 7.67 = 0.80
0115 Coolie day 0.80 645.00 516.00
9999 Sundries L.S. 10.01 2.12 21.22
9999 Wire brushes for cleaning L.S. 17.81 2.12 37.76
9999 Extra for delays L.S. 101.4 2.12 214.97
TOTAL 2260.88 W
Add 1 % Water charges on "W" 22.61
TOTAL 2283.49 X
Add GST on "X" (multiplying
factor 0.1405) 320.83
TOTAL 2604.32 Y
Add 15% CPOH on "Y" 390.65
TOTAL 2994.97 Z
Add Cess @ 1% on "Z" 29.95
Cost of 30.00 metres 3024.92
Cost of 1.00 metre 100.83
Say 100.85
SUB HEAD : 13- FINISHING 1073
13.96 Painting (one or more coats) on rain water, soil waste and vent pipes and
fittings with synthetic enamel paint of approved brand and manufacture and
required colour on old work :
13.96.1 75 mm diameter pipes
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres
Area = 22/7x0.0814 mmx30 m
= 7.67 sqm
MATERIAL
0826 Aluminium paint litre 0.35 150.00 52.50
9999 Putty, sand paper etc. L.S. 0.39 2.12 0.83
9977 Carriage L.S. 2.08 2.12 4.41
LABOUR
0131 Painter day 0.28 714.00 199.92
0115 Coolie day 0.28 645.00 180.60
9999 Putty, sand paper brushes etc. L.S. 4.16 2.12 8.82
9999 Sundries L.S. 6.24 2.12 13.23
9999 Wire brushes for cleaning L.S. 4.42 2.12 9.37
9999 Extra for delay L.S. 26.91 2.12 57.05
TOTAL 526.72 W
Add 1 % Water charges on "W" 5.27
TOTAL 531.99 X
Add GST on "X" (multiplying
factor 0.1405) 74.74
TOTAL 606.74 Y
Add 15% CPOH on "Y" 91.01
TOTAL 697.75 Z
Add Cess @ 1% on "Z" 6.98
Cost of 30.00 metres 704.72
Cost of 1.00 metre 23.49
Say 23.50
13.96.2 100 mm diameter pipes
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres
Area = 22/7x106.4 mmx30 m
= 10.032 sqm
MATERIAL
0826 Aluminium paint litre 0.46 150.00 69.00
9999 Putty, sand paper etc. L.S. 0.52 2.12 1.10
9977 Carriage L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Putty, sand paper brushes etc. L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
9999 Wire brushes for cleaning L.S. 5.33 2.12 11.30
SUB HEAD : 13- FINISHING 1074
Code Description Unit Quantity Rate Amount
9999 Extra for delay L.S. 34.06 2.12 72.21
TOTAL 677.02 W
Add 1 % Water charges on "W" 6.77
TOTAL 683.79 X
Add GST on "X" (multiplying
factor 0.1405) 96.07
TOTAL 779.87 Y
Add 15% CPOH on "Y" 116.98
TOTAL 896.85 Z
Add Cess @ 1% on "Z" 8.97
Cost of 30.00 metres 905.82
Cost of 1.00 metre 30.19
Say 30.20
13.96.3 150 mm diameter pipes
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres
Area = 22/7x157.2 mmx30 m
= 14.82 sqm
MATERIAL
0826 Aluminium paint litre 0.68 150.00 102.00
9999 Putty, sand paper etc. L.S. 0.65 2.12 1.38
9977 Carriage L.S. 3.90 2.12 8.27
LABOUR
0131 Painter day 0.53 714.00 378.42
0115 Coolie day 0.53 645.00 341.85
9999 Putty, sand paper brushes etc. L.S. 7.93 2.12 16.81
9999 Sundries L.S. 11.96 2.12 25.36
9999 Wire brushes for cleaning L.S. 7.15 2.12 15.16
9999 Extra for delay L.S. 40.30 2.12 85.44
TOTAL 974.68 W
Add 1 % Water charges on "W" 9.75
TOTAL 984.42 X
Add GST on "X" (multiplying
factor 0.1405) 138.31
TOTAL 1122.74 Y
Add 15% CPOH on "Y" 168.41
TOTAL 1291.15 Z
Add Cess @ 1% on "Z" 12.91
Cost of 30.00 metres 1304.06
Cost of 1.00 metre 43.47
Say 43.45
13.97 Painting with oil type wood preservative of approved brand and manufacture:
13.97.1 Old work (one or more coats)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0859 Oil type wood preservative litre 0.81 130.00 105.30
9977 Carriage of material L.S. 0.52 2.12 1.10
SUB HEAD : 13- FINISHING 1075
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 0.11 714.00 78.54
0115 Coolie day 0.11 645.00 70.95
9999 Brushes etc L.S. 2.73 2.12 5.79
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 267.47 W
Add 1 % Water charges on "W" 2.67
TOTAL 270.14 X
Add GST on "X" (multiplying
factor 0.1405) 37.95
TOTAL 308.10 Y
Add 15% CPOH on "Y" 46.21
TOTAL 354.31 Z
Add Cess @ 1% on "Z" 3.54
Cost of 10.00 sqm 357.85
Cost of 1.00 sqm 35.79
Say 35.80
13.98 Wall painting with plastic emulsion paint of approved brand and manufacture
to give an even shade:
13.98.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0804 Premium plastic acrylic emulsion of
interior grade, having VOC content less
than 50 grams/ litre litre 0.73 200.00 146.00
9999 Material for filling holes and cracks
(putty etc.) L.S. 0.52 2.12 1.10
9977 Carriage of material L.S. 5.33 2.12 11.30
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 8.06 2.12 17.09
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 679.06 W
Add 1 % Water charges on "W" 6.79
TOTAL 685.85 X
Add GST on "X" (multiplying
factor 0.1405) 96.36
TOTAL 782.21 Y
Add 15% CPOH on "Y" 117.33
TOTAL 899.55 Z
Add Cess @ 1% on "Z" 9.00
Cost of 10.00 sqm 908.54
Cost of 1.00 sqm 90.85
Say 90.85
SUB HEAD : 13- FINISHING 1076
13.99 Painting with synthetic enamel paint of approved brand and manufacture of
required colour to give an even shade :
13.99.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 0.70 175.00 122.50
9977 Carriage of paint and materials L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Putty L.S. 2.73 2.12 5.79
9999 Brushes sand paper etc. L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 647.02 W
Add 1 % Water charges on "W" 6.47
TOTAL 653.49 X
Add GST on "X" (multiplying
factor 0.1405) 91.81
TOTAL 745.30 Y
Add 15% CPOH on "Y" 111.80
TOTAL 857.10 Z
Add Cess @ 1% on "Z" 8.57
Cost of 10.00 sqm 865.67
Cost of 1.00 sqm 86.57
Say 86.55
13.100 Painting with aluminium paint of approved brand and manufacture to give an
even shade:
13.100.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0826 Aluminium paint litre 0.46 150.00 69.00
9977 Carriage of paint and material L.S. 0.52 2.12 1.10
9999 Putty etc L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 593.52 W
Add 1 % Water charges on "W" 5.94
TOTAL 599.45 X
Add GST on "X" (multiplying
factor 0.1405) 84.22
TOTAL 683.67 Y
Add 15% CPOH on "Y" 102.55
TOTAL 786.23 Z
Add Cess @ 1% on "Z" 7.86
Cost of 10.00 sqm 794.09
Cost of 1.00 sqm 79.41
Say 79.40
SUB HEAD : 13- FINISHING 1077
13.101 Painting with acid proof paint of approved brand and manufacture of required
colour to give an even shade :
13.101.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0827 Acid proof paint (chocolate or black) litre 0.70 225.00 157.50
9977 Carriage of paint L.S. 0.52 2.12 1.10
9999 Putty etc L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 682.02 W
Add 1 % Water charges on "W" 6.82
TOTAL 688.84 X
Add GST on "X" (multiplying
factor 0.1405) 96.78
TOTAL 785.62 Y
Add 15% CPOH on "Y" 117.84
TOTAL 903.46 Z
Add Cess @ 1% on "Z" 9.03
Cost of 10.00 sqm 912.50
Cost of 1.00 sqm 91.25
Say 91.25
13.102 Painting with black anti-corrosive bitumastic paint of approved brand and
manufacture to give an even shade :
13.102.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.57 100.00 57.00
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Putty, brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 575.73 W
Add 1 % Water charges on "W" 5.76
TOTAL 581.49 X
Add GST on "X" (multiplying
factor 0.1405) 81.70
TOTAL 663.19 Y
Add 15% CPOH on "Y" 99.48
TOTAL 762.66 Z
Add Cess @ 1% on "Z" 7.63
Cost of 10.00 sqm 770.29
Cost of 1.00 sqm 77.03
Say 77.05
SUB HEAD : 13- FINISHING 1078
13.103 French spirit polishing :
13.103.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
1000 Spirit litre 0.98 48.00 47.04
0999 Shellac kilogram 0.13 300.00 39.00
9977 Carriage of materials L.S. 0.91 2.12 1.93
9999 Turpentine oil sand paper cotton/woolen
cloth putty etc. L.S. 10.79 2.12 22.87
9999 Linseed oil L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 1.76 714.00 1256.64
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1385.67 W
Add 1 % Water charges on "W" 13.86
TOTAL 1399.53 X
Add GST on "X" (multiplying
factor 0.1405) 196.63
TOTAL 1596.16 Y
Add 15% CPOH on "Y" 239.42
TOTAL 1835.59 Z
Add Cess @ 1% on "Z" 18.36
Cost of 10.00 sqm 1853.94
Cost of 1.00 sqm 185.39
Say 185.40
13.104 Polishing on wood work with ready made wax polish of approved brand and
manufacture :
13.104.1 Old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0855 Wax polish (ready made) kilogram 0.25 230.00 57.50
9977 Caariage L.S. 0.39 2.12 0.83
LABOUR
0131 Painter day 0.40 714.00 285.60
0115 Coolie day 0.40 645.00 258.00
9999 Soap, brushes, cloth etc L.S. 4.16 2.12 8.82
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 620.12 W
Add 1 % Water charges on "W" 6.20
TOTAL 626.32 X
Add GST on "X" (multiplying
factor 0.1405) 88.00
TOTAL 714.32 Y
Add 15% CPOH on "Y" 107.15
TOTAL 821.46 Z
Add Cess @ 1% on "Z" 8.21
Cost of 10.00 sqm 829.68
Cost of 1.00 sqm 82.97
Say 82.95
SUB HEAD : 13- FINISHING 1079
13.105 Re-lettering with black Japan paint of approved brand and manufacture.
Code Description Unit Quantity Rate Amount
Detail of cost for 100 letters of
15 cm height
MATERIAL
0829 Black Japan paint litre 0.37 90.00 33.30
9977 Carriage L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 4.00 714.00 2856.00
0115 Coolie day 1.00 645.00 645.00
9999 Painting brushes, turpentine, stencil etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 3567.65 W
Add 1 % Water charges on "W" 35.68
TOTAL 3603.32 X
Add GST on "X" (multiplying
factor 0.1405) 506.27
TOTAL 4109.59 Y
Add 15% CPOH on "Y" 616.44
TOTAL 4726.03 Z
Add Cess @ 1% on "Z" 47.26
Cost of 100 letters of 15 cm height 4773.29
Cost per letter per cm height 3.18
Say 3.20
13.106 Painting (one or more coats) with black Japan paint of approved brand and
manufacture to give an even shade.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0829 Black Japan paint litre 0.70 90.00 63.00
9977 Carriage L.S. 0.52 2.12 1.10
9999 Putty etc. L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc. L.S. 5.33 2.12 11.30
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 587.52 W
Add 1 % Water charges on "W" 5.88
TOTAL 593.39 X
Add GST on "X" (multiplying
factor 0.1405) 83.37
TOTAL 676.76 Y
Add 15% CPOH on "Y" 101.51
TOTAL 778.28 Z
Add Cess @ 1% on "Z" 7.78
Cost of 10.00 sqm 786.06
Cost of 1sqm 78.61
Say 78.60
SUB HEAD : 13- FINISHING 1080
13.107 Providing and fixing C.P. brass chain and rubber plug complete for sink or
wash basin:
13.107.1 32 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for 1 no.
MATERIAL
1314 C.P.brass chain with 32 mm dia
rubber plug each 1.00 40.00 40.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 57.09 W
Add 1 % Water charges on "W" 0.57
TOTAL 57.66 X
Add GST on "X" (multiplying
factor 0.1405) 8.10
TOTAL 65.76 Y
Add 15% CPOH on "Y" 9.86
TOTAL 75.62 Z
Add Cess @ 1% on "Z" 0.76
Cost of each 76.38
Say 76.40
13.107.2 40 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for 1 no.
MATERIAL
1315 C.P.brass chain with 40 mm dia
rubber plug each 1.00 40.00 40.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 57.09 W
Add 1 % Water charges on "W" 0.57
TOTAL 57.66 X
Add GST on "X" (multiplying
factor 0.1405) 8.10
TOTAL 65.76 Y
Add 15% CPOH on "Y" 9.86
TOTAL 75.62 Z
Add Cess @ 1% on "Z" 0.76
Cost of each 76.38
Say 76.40
13.108 Distempering with 1st quality acrylic distemper (ready made) having VOC
content less than 50 gm per ltr. of approved manufacturer and of required
shade and colour complete. as per manufacturer's specification.
13.108.1 One or more coats on old work
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0802 Acrylic distemper 1st quality , having
VOC content less than 50 grams/ litre kilogram 1.00 40.00 40.00
SUB HEAD : 13- FINISHING 1081
Code Description Unit Quantity Rate Amount
9999 Brushes, putty etc L.S. 0.52 2.12 1.10
9988 Sundries including carriage of material L.S. 10.76 2.12 22.81
LABOUR
0131 Painter day 0.22 714.00 157.08
0114 Beldar day 0.22 645.00 141.90
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 378.05 W
Add 1 % Water charges on "W" 3.78
TOTAL 381.83 X
Add GST on "X" (multiplying
factor 0.1405) 53.65
TOTAL 435.48 Y
Add 15% CPOH on "Y" 65.32
TOTAL 500.80 Z
Add Cess @ 1% on "Z" 5.01
Cost of 10.00 sqm 505.81
Cost of 1.00 sqm 50.58
Say 50.60
13.109 Finishing walls with water proofing cement paint of required shade :
13.109.1 Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of
primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0851 Water proofing cement paint kilogram 2.20 38.00 83.60
8508 Primer for cement paint litre 0.80 90.00 72.00
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.46 714.00 328.44
0115 Coolie day 0.23 645.00 148.35
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 703.64 W
Add 1 % Water charges on "W" 7.04
TOTAL 710.68 X
Add GST on "X" (multiplying
factor 0.1405) 99.85
TOTAL 810.53 Y
Add 15% CPOH on "Y" 121.58
TOTAL 932.11 Z
Add Cess @ 1% on "Z" 9.32
Cost of 10.00 sqm 941.43
Cost of 1.00 sqm 94.14
Say 94.15
SUB HEAD : 13- FINISHING 1082
13.109.2 Old work (one or more coats @ 2.20 kg/10 sqm) complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0851 Water proofing cement paint kilogram 2.20 38.00 83.60
9977 Carriage of material L.S. 1.10 2.12 2.33
LABOUR
0131 Painter day 0.35 714.00 249.90
0115 Coolie day 0.12 645.00 77.40
0101 Bhisti day 0.05 714.00 35.70
9999 Brushes, sand paper etc L.S. 3.15 2.12 6.68
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 472.70 W
Add 1 % Water charges on "W" 4.73
TOTAL 477.42 X
Add GST on "X" (multiplying
factor 0.1405) 67.08
TOTAL 544.50 Y
Add 15% CPOH on "Y" 81.68
TOTAL 626.18 Z
Add Cess @ 1% on "Z" 6.26
Cost of 10.00 sqm 632.44
Cost of 1.00 sqm 63.24
Say 63.25
13.110 Finishing walls with textured exterior paint of required shade :
13.110.1 Old work (Two or more coats on existing cement paint surface applied @ 3.28
ltr/10 sqm.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8507 Textured exterior paint litre 3.28 280.00 918.40
9977 Carriage of material L.S. 1.56 2.12 3.31
LABOUR
0131 Painter day 0.46 714.00 328.44
0115 Coolie day 0.23 645.00 148.35
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1430.74 W
Add 1 % Water charges on "W" 14.31
TOTAL 1445.05 X
Add GST on "X" (multiplying
factor 0.1405) 203.03
TOTAL 1648.08 Y
Add 15% CPOH on "Y" 247.21
TOTAL 1895.29 Z
Add Cess @ 1% on "Z" 18.95
Cost of 10.00 sqm 1914.24
Cost of 1.00 sqm 191.42
Say 191.40
SUB HEAD : 13- FINISHING 1083
13.110.2 Old work (One or more coats) applied @ 1.82 ltr/10 sqm.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8507 Textured exterior paint litre 1.82 280.00 509.60
9977 Carriage of material L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.33 714.00 235.62
0115 Coolie day 0.17 645.00 109.65
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 888.22 W
Add 1 % Water charges on "W" 8.88
TOTAL 897.10 X
Add GST on "X" (multiplying
factor 0.1405) 126.04
TOTAL 1023.14 Y
Add 15% CPOH on "Y" 153.47
TOTAL 1176.61 Z
Add Cess @ 1% on "Z" 11.77
Cost of 10.00 sqm 1188.38
Cost of 1.00 sqm 118.84
Say 118.85
13.111 Finishing walls with Acrylic Smooth exterior paint of required shade :
13.111.1 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement
paint surface
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8505 Acrylic exterior paint litre 1.67 200.00 334.00
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 0.46 714.00 328.44
0115 Coolie day 0.23 645.00 148.35
9999 Brushes, sand paper etc L.S. 4.81 2.12 10.20
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 834.22 W
Add 1 % Water charges on "W" 8.34
TOTAL 842.56 X
Add GST on "X" (multiplying
factor 0.1405) 118.38
TOTAL 960.94 Y
Add 15% CPOH on "Y" 144.14
TOTAL 1105.08 Z
Add Cess @ 1% on "Z" 11.05
Cost of 10.00 sqm 1116.13
Cost of 1.00 sqm 111.61
Say 111.60
SUB HEAD : 13- FINISHING 1084
13.111.2 Old work (One or more coat applied @ 0.90 ltr/10 sqm).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8505 Acrylic exterior paint litre 0.90 200.00 180.00
9977 Carriage of material L.S. 0.52 2.12 1.10
LABOUR
0131 Painter day 0.33 714.00 235.62
0115 Coolie day 0.17 645.00 109.65
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 558.62 W
Add 1 % Water charges on "W" 5.59
TOTAL 564.20 X
Add GST on "X" (multiplying
factor 0.1405) 79.27
TOTAL 643.47 Y
Add 15% CPOH on "Y" 96.52
TOTAL 740.00 Z
Add Cess @ 1% on "Z" 7.40
Cost of 10.00 sqm 747.40
Cost of 1.00 sqm 74.74
Say 74.75
13.112 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone
additives of required shade
13.112.1 Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement
paint surface
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8506 Premium Acrylic exterior paint litre 1.43 210.00 300.30
9977 Carriage of material L.S. 1.04 2.12 2.20
LABOUR
0131 Painter day 0.46 714.00 328.44
0115 Coolie day 0.23 645.00 148.35
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 811.54 W
Add 1 % Water charges on “W” 8.12
TOTAL 819.66 X
Add GST on “X” (multiplying
factor 0.1405) 115.16
TOTAL 934.82 Y
Add 15% CPOH on “Y” 140.22
TOTAL 1075.04 Z
Add Cess @ 1% on “Z” 10.75
Cost of 10.00 sqm 1085.79
Cost of 1.00 sqm 108.58
Say 108.60
SUB HEAD : 13- FINISHING 1085
13.112.2 Old work (one or more coats applied @ 0.83 ltr/10 sqm).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
8506 Premium Acrylic exterior paint litre 0.83 210.00 174.30
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0131 Painter day 0.33 714.00 235.62
0115 Coolie day 0.17 645.00 109.65
9999 Brushes, sand paper etc L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 553.74 W
Add 1 % Water charges on "W" 5.54
TOTAL 559.28 X
Add GST on "X" (multiplying
factor 0.1405) 78.58
TOTAL 637.86 Y
Add 15% CPOH on "Y" 95.68
TOTAL 733.54 Z
Add Cess @ 1% on "Z" 7.34
Cost of 10.00 sqm 740.88
Cost of 1.00 sqm 74.09
Say 74.10
13.113 Varnishing with varnish of approved brand and manufacture:
13.113.1 One or more coats with copal varnish
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0857 Superior copal varnish litre 0.70 115.00 80.50
9977 Carriage L.S. 0.52 2.12 1.10
9999 Repair to the surface L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 5.33 2.12 11.30
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 593.72 W
Add 1 % Water charges on "W" 5.94
TOTAL 599.65 X
Add GST on "X" (multiplying
factor 0.1405) 84.25
TOTAL 683.91 Y
Add 15% CPOH on "Y" 102.59
TOTAL 786.49 Z
Add Cess @ 1% on "Z" 7.86
Cost of 10.00 sqm 794.36
Cost of 1.00 sqm 79.44
Say 79.45
SUB HEAD : 13- FINISHING 1086
13.113.2 One or more coats with spar varnish
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0858 Superior spar varnish litre 0.75 115.00 86.25
9977 Carriage L.S. 0.52 2.12 1.10
9999 Repair etc L.S. 2.73 2.12 5.79
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
9999 Brushes, sand paper etc L.S. 2.73 2.12 5.79
9999 Sundries L.S. 4.16 2.12 8.82
TOTAL 596.99 W
Add 1 % Water charges on "W" 5.97
TOTAL 602.96 X
Add GST on "X" (multiplying
factor 0.1405) 84.72
TOTAL 687.67 Y
Add 15% CPOH on "Y" 103.15
TOTAL 790.82 Z
Add Cess @ 1% on "Z" 7.91
Cost of 10.00 sqm 798.73
Cost of 1.00 sqm 79.87
Say 79.85
13.114 Melamine polishing on wood work (one or more coat).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
7241 Melamine polish litre 0.65 300.00 195.00
0006 Hire charges of Spraying machine
including
electric charges day 0.78 250.00 195.00
9988 Carriage charge of Machine & Marerial L.S. 4.42 2.12 9.37
LABOUR
0131 Painter day 0.35 714.00 249.90
0114 Beldar day 0.35 645.00 225.75
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 884.39 W
Add 1 % Water charges on "W" 8.84
TOTAL 893.23 X
Add GST on "X" (multiplying
factor 0.1405) 125.50
TOTAL 1018.73 Y
Add 15% CPOH on "Y" 152.81
TOTAL 1171.54 Z
Add Cess @ 1% on "Z" 11.72
Cost of 10.00 sqm 1183.26
Cost of 1.00 sqm 118.33
Say 118.35
SUB HEAD : 13- FINISHING 1087
13.115 Varnishing with flatting varnish of approved brand and manufacture one or
more coats on old work.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
0856 Ordinary varnish litre 0.70 100.00 70.00
9999 Glue, putty etc L.S. 2.73 2.12 5.79
9977 Carriage L.S. 1.82 2.12 3.86
9999 Painting brushes, turpentine, stencil etc L.S. 24.18 2.12 51.26
LABOUR
0131 Painter day 0.36 714.00 257.04
0115 Coolie day 0.36 645.00 232.20
TOTAL 620.15 W
Add 1 % Water charges on "W" 6.20
TOTAL 626.35 X
Add GST on "X" (multiplying
factor 0.1405) 88.00
TOTAL 714.35 Y
Add 15% CPOH on "Y" 107.15
TOTAL 821.50 Z
Add Cess @ 1% on "Z" 8.22
Cost of 10.00 sqm 829.72
Cost of 1.00 sqm 82.97
Say 82.95
13.116 Polishing in high gloss/matt finish melamine clear polish on wood work in
required color/wooden shade texture with following process in the sequence
as detailed below:
1. The surface to be polished is rubbed with sand paper 80/120 no. and then
with sand paper of 160/180 nos.
2. Applying two coats of sealer with spray gun and allowing sufficient drying
time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.
3. On drying of sealer coat, wet rubbing with emery cloth of finer grading
with ample water to remove excess sealer layer and make the surface further
smooth after this wet rubbing, then surface is applied with special grade
melamine fillers to fill all the small and big holes/grooves etc. Filler coat to
be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done
this surface is further allowed to dry for 12 hrs.
4. On this, 1st coat of melamine polish is applied with spray gun using
melamine clear polish and melamine thinner in required proportion. This
1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet
rubbed smooth, which is further allowed to dry for 12 hrs. The final
melamine polish is applied with compressor pressure spray gun using
melamine clear polish and melamine thinner mixed in required proportion
complete as per direction of Engineer-in-Charge. (Final coat to be done in
1 or 2 layers without gap of time.)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
7241 Melamine Matt clear polish litre 1.56 300.00 468.00
SUB HEAD : 13- FINISHING 1088
Code Description Unit Quantity Rate Amount
5766 Melamine wood sealer litre 2.80 190.00 532.00
5767 Melamine solvent/thinner litre 2.85 120.00 342.00
5768 Sanding cloth 150 mm wide metre 6.00 60.00 360.00
5769 Sand papers of assorted gratings Nos 16.00 22.00 352.00
5770 Melamine wood filler putty Kg 1.50 120.00 180.00
5771 Dhoti (worm out soft cotton cloth) Nos 2.00 25.00 50.00
LABOUR
0167 Polisher 1st class day 1.66 784.00 1301.44
0168 Polisher 2nd class day 3.25 714.00 2320.50
0114 Beldrs/Coolies day 2.00 645.00 1290.00
0006 Hire charges of compressor machine
spare gun etc., with electric charges day 1.25 250.00 312.50
9999 Sundries including scaffolding &
T&P etc. L.S. 300.00 2.12 636.00
5779 Grinding buffers day 2.00 250.00 500.00
TOTAL 8644.44 W
Add 1 % Water charges on "W" 86.44
TOTAL 8730.88 X
Add GST on "X" (multiplying
factor 0.1405) 1226.69
TOTAL 9957.57 Y
Add 15% CPOH on "Y" 1493.64
TOTAL 11451.21 Z
Add Cess @ 1% on "Z" 114.51
Cost of 10.00 sqm 11565.72
Cost of 1.00 sqm 1156.57
Say 1156.55
SUB HEAD : 13- FINISHING 1089
SUB HEAD : 14.0
REPAIRS TO BUILDING
1091
14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters
and under, including cutting the patch in proper shape, raking out joints and
preparing and plastering the surface of the walls complete, including disposal
of rubbish to the dumping ground, all complete as per direction of Engineer-
in-Charge.
14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 fine sand)
3.4 Rate as per Item Number 3.4 of
SH: Mortars cum 0.183 3713.20 679.52
LABOUR
0155 Mason (average) day 1.21 749.00 906.29
0115 Coolie day 1.29 645.00 832.05
0114 Beldar day 0.54 645.00 348.30
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 15.21 2.12 32.25
TOTAL 3455.28 W
Add 1 % Water charges on "W" 34.55
TOTAL 3489.83 X
Add GST on "X" (multiplying
factor 0.1405) 490.32
TOTAL 3980.16 Y
Add 15% CPOH on "Y" 597.02
TOTAL 4577.18 Z
Add Cess @ 1% on "Z" 45.77
Cost of 10.00 sqm 4622.95
Cost of 1.00 sqm 462.30
Say 462.30
14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.183 4355.20 797.00
LABOUR
0155 Mason (average) day 1.21 749.00 906.29
0115 Coolie day 1.29 645.00 832.05
0114 Beldar day 0.54 645.00 348.30
0101 Bhisti day 0.92 714.00 656.88
SUB HEAD : 14- REPAIRS TO BUILDING 1093
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 15.21 2.12 32.25
TOTAL 3572.77 W
Add 1 % Water charges on "W" 35.73
TOTAL 3608.49 X
Add GST on "X" (multiplying
factor 0.1405) 506.99
TOTAL 4115.49 Y
Add 15% CPOH on "Y" 617.32
TOTAL 4732.81 Z
Add Cess @ 1% on "Z" 47.33
Cost of 10.00 sqm 4780.14
Cost of 1.00 sqm 478.01
Say 478.00
14.2 Fixing chowkhats in existing opening including embedding chowkhats in floors
or walls cutting masonry for holdfasts, embedding hold fasts in cement
concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement
: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two
coats of approved wood preservative to sides of chowkhats and making good
the damages to walls and floors as required complete, including disposal of
rubbish to the dumping ground, all complete as per direction of Engineer-in-
Charge.
14.2.1 Door chowkhats
Code Description Unit Quantity Rate Amount
Detail of cost for each
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.021 1400.00 29.40
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.0072 1350.00 9.72
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.0282 163.93 4.62
0982 Coarse sand (zone III) cum 0.0141 1500.00 21.15
2203 Carriage of Coarse sand cum 0.0141 163.93 2.31
0367 Portland Cement (OPC-43 grade) tonne 0.0066 5000.00 33.00
2209 Carriage of Cement tonne 0.0066 145.72 0.96
0114 Beldar day 0.027 645.00 17.42
0115 Coolie day 0.0195 645.00 12.58
0130 Mistry day 0.0084 784.00 6.59
0123 Mason (brick layer) 1st class day 0.0018 784.00 1.41
0124 Mason (brick layer) 2nd class day 0.0018 714.00 1.29
0128 Mate day 0.0012 714.00 0.86
9999 Scaffolding L.S. 1.43 2.12 3.03
9999 Hire and running charges of mechanical
mixer L.S. 0.78 2.12 1.65
9999 Sundries L.S. 0.39 2.12 0.83
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.01 3044.30 30.44
9999 Cement concrete 1:2:4 filled in
chase cut L.S. 24.18 2.12 51.26
SUB HEAD : 14- REPAIRS TO BUILDING 1094
Code Description Unit Quantity Rate Amount
9999 Painting two coats of coaltar L.S. 13.52 2.12 28.66
9999 Disposal of mulba L.S. 1.82 2.12 3.86
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.75 645.00 483.75
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 1125.07 W
Add 1 % Water charges on "W" 11.25
TOTAL 1136.32 X
Add GST on "X" (multiplying
factor 0.1405) 159.65
TOTAL 1295.98 Y
Add 15% CPOH on "Y" 194.40
TOTAL 1490.37 Z
Add Cess @ 1% on "Z" 14.90
Cost of each 1505.28
Say 1505.30
14.2.2 Window chowkhats
Code Description Unit Quantity Rate Amount
Detail of cost for each
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 0.014 1400.00 19.60
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 0.0048 1350.00 6.48
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.0188 163.93 3.08
0982 Coarse sand (zone III) cum 0.0094 1500.00 14.10
2203 Carriage of Coarse sand cum 0.0094 163.93 1.54
0367 Portland Cement (OPC-43 grade) tonne 0.0044 5000.00 22.00
2209 Carriage of Cement tonne 0.0044 145.72 0.64
0114 Beldar day 0.018 645.00 11.61
0115 Coolie day 0.013 645.00 8.39
0130 Mistry day 0.0056 784.00 4.39
0123 Mason (brick layer) 1st class day 0.0012 784.00 0.94
0124 Mason (brick layer) 2nd class day 0.0012 714.00 0.86
0128 Mate day 0.0008 714.00 0.57
9999 Scaffolding and sundries L.S. 0.91 2.12 1.93
9999 Hire and running charges of
mechanical mixer L.S. 0.52 2.12 1.10
9999 Sundries L.S. 0.26 2.12 0.55
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.006 3044.30 18.27
9999 Cement concrete 1:2:4 L.S. 9.88 2.12 20.95
9999 Painting two coats of coaltar L.S. 0.91 2.12 1.93
0155 Mason (average) day 0.33 749.00 247.17
SUB HEAD : 14- REPAIRS TO BUILDING 1095
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.50 645.00 322.50
TOTAL 708.59 W
Add 1 % Water charges on "W" 7.09
TOTAL 715.68 X
Add GST on "X" (multiplying
factor 0.1405) 100.55
TOTAL 816.23 Y
Add 15% CPOH on "Y" 122.43
TOTAL 938.66 Z
Add Cess @ 1% on "Z" 9.39
Cost of each 948.05
Say 948.05
14.2.3 Clerestory window chowkhats
Code Description Unit Quantity Rate Amount
Detail of cost for each
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 0.007 1400.00 9.80
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 0.0024 1350.00 3.24
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.0094 163.93 1.54
0982 Coarse sand (zone III) cum 0.0047 1500.00 7.05
2203 Carriage of Coarse sand cum 0.0047 163.93 0.77
0367 Portland Cement (OPC-43 grade) tonne 0.0022 5000.00 11.00
2209 Carriage of Cement tonne 0.0022 145.72 0.32
0114 Beldar day 0.009 645.00 5.81
0115 Coolie day 0.0065 645.00 4.19
0130 Mistry day 0.0028 784.00 2.20
0123 Mason (brick layer) 1st class day 0.0006 784.00 0.47
0124 Mason (brick layer) 2nd class day 0.0006 714.00 0.43
0128 Mate day 0.0004 714.00 0.29
9999 Scaffolding and sundries L.S. 0.52 2.12 1.10
9999 Hire and running charges of mechanical
mixer L.S. 0.26 2.12 0.55
9999 Sundries L.S. 0.13 2.12 0.28
Cement mortar 1 : 6 (1 cement :
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.003 3044.30 9.13
9999 Cement concrete 1:2:4 filled in
chase cut L.S. 8.06 2.12 17.09
9999 Painting two coats of coaltar L.S. 0.91 2.12 1.93
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.50 645.00 322.50
SUB HEAD : 14- REPAIRS TO BUILDING 1096
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 532.80 W
Add 1 % Water charges on "W" 5.33
TOTAL 538.12 X
Add GST on "X" (multiplying
factor 0.1405) 75.61
TOTAL 613.73 Y
Add 15% CPOH on "Y" 92.06
TOTAL 705.79 Z
Add Cess @ 1% on "Z" 7.06
Cost of each 712.85
Say 712.85
14.3 Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/
Chemical fasteners of appropriate size (3 nos on each vertical member of door
chowkhat and 2 nos on each vertical member of window chowkhats), including
Cost of dash fasteners/ chemical fastener.
Code Description Unit Quantity Rate Amount
Details of cost for 1 chowkhat.
0114 Beldar day 0.027 645.00 17.42
0115 Coolie day 0.0195 645.00 12.58
0130 Mistry day 0.0084 784.00 6.59
0128 Mate day 0.0012 714.00 0.86
9999 Disposal of mulba L.S. 1.82 2.12 3.86
7019 Dash fastner/ chemical fastener each 6.00 12.50 75.00
9999 Hire charges of drill machine hire
charges, Scaffolding and Sundries L.S. 12.22 2.12 25.91
TOTAL 142.20 W
Add 1 % Water charges on "W" 1.42
TOTAL 143.62 X
Add GST on "X" (multiplying
factor 0.1405) 20.18
TOTAL 163.80 Y
Add 15% CPOH on "Y" 24.57
TOTAL 188.37 Z
Add Cess @ 1% on "Z" 1.88
Cost of each 190.25
Say 190.25
14.4 Making the opening in brick masonry including dismantling in floor or walls
by cutting masonry and making good the damages to walls, flooring and jambs
complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest
municipal dumping ground, all complete as per direction of Engineer-in-
Charge.
14.4.1 For door/ window/ clerestory window
Code Description Unit Quantity Rate Amount
Details of cost for one opening of size
0.90x2.10m = 1.89 sqm
SUB HEAD : 14- REPAIRS TO BUILDING 1097
Code Description Unit Quantity Rate Amount
Cement mortar 1:6 (1 cement:
6 fine sand)
3.6 Rate as per Item Number 3.6 of
SH: Mortars cum 0.01 3044.30 30.44
9999 Cement concrete 1:2:4 filled in chase cut L.S. 24.57 2.12 52.09
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.20 645.00 774.00
0115 Coolie day 0.40 645.00 258.00
9999 Scaffolding and Sundries L.S. 3.50 2.12 7.42
TOTAL 1478.95 W
Add 1 % Water charges on "W" 14.79
TOTAL 1493.74 X
Add GST on "X" (multiplying
factor 0.1405) 209.87
TOTAL 1703.61 Y
Add 15% CPOH on "Y" 255.54
TOTAL 1959.15 Z
Add Cess @ 1% on "Z" 19.59
Cost of 1.89sqm. 1978.74
Cost of 1.00 sqm. 1046.95
Say 1046.95
14.5 Renewing glass panes, with putty and nails wherever necessary including
racking out the old putty:
14.5.1 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area
each 0.1sqm.
MATERIAL
2406 Float glass panes of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.10 309.00 339.90
1.00 sqm + 10% wastage= 1.10 Sqm
9988 Carriage including sundries L.S. 1.82 2.12 3.86
0863 Putty for wood work kilogram 0.68 28.00 19.04
9999 Painting or varnishing or beewaxing L.S. 5.33 2.12 11.30
9999 Sundries Nails etc. L.S. 6.76 2.12 14.33
0119 Glazier day 0.23 714.00 164.22
0114 Beldar day 0.23 645.00 148.35
9999 Sundries such as Rag, cotton etc L.S. 1.43 2.12 3.03
TOTAL 704.03 W
Add 1 % Water charges on "W" 7.04
TOTAL 711.07 X
Add GST on "X" (multiplying
factor 0.1405) 99.91
TOTAL 810.98 Y
Add 15% CPOH on "Y" 121.65
TOTAL 932.62 Z
Add Cess @ 1% on "Z" 9.33
Cost of 1.00 sqm 941.95
Say 941.95
SUB HEAD : 14- REPAIRS TO BUILDING 1098
14.5.2 Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area
each 0.1sqm.
MATERIAL
2407 Float glass panes of nominal thickness
5 mm (weight not less than 12.5kg/sqm) sqm 1.10 515.00 566.50
1.00 sqm + 10% wastage= 1.10 Sqm
9988 Carriage including sundries L.S. 1.82 2.12 3.86
0863 Putty for wood work kilogram 0.68 28.00 19.04
9999 Painting or varnishing or beewaxing L.S. 5.33 2.12 11.30
9999 Sundries Nails etc. L.S. 6.76 2.12 14.33
0119 Glazier day 0.23 714.00 164.22
0114 Beldar day 0.23 645.00 148.35
9999 Sundries such as Rag, cotton etc L.S. 1.43 2.12 3.03
TOTAL 930.63 W
Add 1 % Water charges on "W" 9.31
TOTAL 939.94 X
Add GST on "X" (multiplying
factor 0.1405) 132.06
TOTAL 1072.00 Y
Add 15% CPOH on "Y" 160.80
TOTAL 1232.80 Z
Add Cess @ 1% on "Z" 12.33
Cost of 1.00 sqm 1245.13
Say 1245.15
14.6 Renewing glass panes, with wooden fillets wherever necessary:
14.6.1 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area
each 0.1sqm.
MATERIAL
2406 Float glass panes of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.10 309.00 339.90
1.00 sqm + 10% wastage= 1.10 Sqm
1189 Second class teak wood in scantling 10 cudm 0.025 776.00 19.40
1194 Second class deodar wood in planks 10 cudm 0.025 500.00 12.50
1196 First class kail wood in planks 10 cudm 0.025 300.00 7.50
9999 Painting or varnishing or beewaxing L.S. 4.42 2.12 9.37
9999 Sundries Nails etc. L.S. 2.73 2.12 5.79
0112 Carpenter 2nd class day 0.20 714.00 142.80
0119 Glazier day 0.25 714.00 178.50
0114 Beldar day 0.45 645.00 290.25
9999 Sundries such as Rag, cotton etc L.S. 1.82 2.12 3.86
TOTAL 1009.87 W
Add 1 % Water charges on "W" 10.10
TOTAL 1019.97 X
Add GST on "X" (multiplying
factor 0.1405) 143.31
TOTAL 1163.27 Y
Add 15% CPOH on "Y" 174.49
TOTAL 1337.76 Z
Add Cess @ 1% on "Z" 13.38
Cost of 1.00 sqm 1351.14
Say 1351.15
SUB HEAD : 14- REPAIRS TO BUILDING 1099
14.6.2 Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area
each 0.1sqm.
MATERIAL
2407 Float glass sheet of nominal thickness
Float glass panes of nominal thickness
5 mm (weight not less than 12.5kg/sqm) sqm 1.10 515.00 566.50
1.00 sqm + 10% wastage= 1.10 Sqm
1189 Second class teak wood in scantling 10 cudm 0.025 776.00 19.40
1194 Second class deodar wood in planks 10 cudm 0.025 500.00 12.50
1196 First class kail wood in planks 10 cudm 0.025 300.00 7.50
9999 Painting or varnishing or beewaxing L.S. 4.42 2.12 9.37
9999 Sundries Nails etc. L.S. 2.73 2.12 5.79
0112 Carpenter 2nd class day 0.20 714.00 142.80
0119 Glazier day 0.25 714.00 178.50
0114 Beldar day 0.45 645.00 290.25
9999 Sundries such as Rag, cotton etc L.S. 1.82 2.12 3.86
TOTAL 1236.47 W
Add 1 % Water charges on "W" 12.36
TOTAL 1248.83 X
Add GST on "X" (multiplying
factor 0.1405) 175.46
TOTAL 1424.29 Y
Add 15% CPOH on "Y" 213.64
TOTAL 1637.94 Z
Add Cess @ 1% on "Z" 16.38
Cost of 1.00 sqm 1654.31
Say 1654.30
14.7 Renewing glass panes and refixing existing wooden fillets:
14.7.1 Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area
each 0.1sqm.
MATERIAL
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.10 309.00 339.90
1.00 sqm + 10% wastage= 1.10 Sqm
9977 Carriage of glasspanes and other
materials L.S. 2.73 2.12 5.79
9999 Sundries Nails etc. L.S. 9.88 2.12 20.95
9999 Methylated spirit L.S. 5.33 2.12 11.30
0119 Glazier day 0.30 714.00 214.20
0114 Beldar day 0.30 645.00 193.50
SUB HEAD : 14- REPAIRS TO BUILDING 1100
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 788.66 W
Add 1 % Water charges on "W" 7.89
TOTAL 796.55 X
Add GST on "X" (multiplying
factor 0.1405) 111.92
TOTAL 908.47 Y
Add 15% CPOH on "Y" 136.27
TOTAL 1044.74 Z
Add Cess @ 1% on "Z" 10.45
Cost of 1.00 sqm 1055.18
Say 1055.20
14.7.2 Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)
Code Description Unit Quantity Rate Amount
Detail of cost for 10 glasses area each
0.1sqm.
MATERIAL
2407 Float glass panes of nominal thickness
5 mm (weight not less than 12.5kg/sqm) sqm 1.10 515.00 566.50
1.00 sqm + 10% wastage= 1.10 Sqm
9977 Carriage of glasspanes and other
materials L.S. 2.73 2.12 5.79
9999 Sundries Nails etc. L.S. 9.88 2.12 20.95
9999 Methylated spirit L.S. 5.33 2.12 11.30
0119 Glazier day 0.30 714.00 214.20
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 1015.26 W
Add 1 % Water charges on "W" 10.15
TOTAL 1025.42 X
Add GST on "X" (multiplying
factor 0.1405) 144.07
TOTAL 1169.49 Y
Add 15% CPOH on "Y" 175.42
TOTAL 1344.91 Z
Add Cess @ 1% on "Z" 13.45
Cost of 1.00 sqm 1358.36
Say 1358.35
14.8 Supplying and fixing new wooden fillets wherever necessary:
14.8.1 2nd class teak wood fillets
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres length
MATERIAL
1190 Second class teak wood in planks 10 cudm 0.115 791.00 90.97
10.00x0.01x0.01 = 1.00 cudm
Add 15% wastage = 0.15 cudm
Total = 1.15 cudm
9999 Nails L.S. 26.91 2.12 57.05
SUB HEAD : 14- REPAIRS TO BUILDING 1101
Code Description Unit Quantity Rate Amount
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 493.55 W
Add 1 % Water charges on "W" 4.94
TOTAL 498.49 X
Add GST on "X" (multiplying
factor 0.1405) 70.04
TOTAL 568.52 Y
Add 15% CPOH on "Y" 85.28
TOTAL 653.80 Z
Add Cess @ 1% on "Z" 6.54
Cost of 10.00 metre 660.34
Cost of 1.00 metre 66.03
Say 66.05
14.8.2 Hollock wood fillets
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres length
MATERIAL
2466 Hollock wood in scantling 10 cudm 0.115 357.00 41.06
10.00x0.01x0.01 = 1.00 cudm
Add 15% wastage = 0.15 cudm
Total = 1.15 cudm
9999 Nails L.S. 26.91 2.12 57.05
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 443.64 W
Add 1 % Water charges on "W" 4.44
TOTAL 448.08 X
Add GST on "X" (multiplying
factor 0.1405) 62.95
TOTAL 511.03 Y
Add 15% CPOH on "Y" 76.65
TOTAL 587.69 Z
Add Cess @ 1% on "Z" 5.88
Cost of 10.00 metre 593.57
Cost of 1.00 metre 59.36
Say 59.35
14.9 Renewal of old putty of glass panes (length)
Code Description Unit Quantity Rate Amount
Details of cost for 13 metres length
MATERIAL
0863 Putty for wood work kilogram 0.68 28.00 19.04
9999 Nails L.S. 7.15 2.12 15.16
9999 Spirit L.S. 2.73 2.12 5.79
SUB HEAD : 14- REPAIRS TO BUILDING 1102
Code Description Unit Quantity Rate Amount
LABOUR
0112 Carpenter 2nd class day 0.30 714.00 214.20
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 450.72 W
Add 1 % Water charges on "W" 4.51
TOTAL 455.22 X
Add GST on "X" (multiplying
factor 0.1405) 63.96
TOTAL 519.18 Y
Add 15% CPOH on "Y" 77.88
TOTAL 597.06 Z
Add Cess @ 1% on "Z" 5.97
Cost of 13.00 metres 603.03
Cost of 1.00 metre 46.39
Say 46.40
14.10 Refixing old glass panes with putty and nails
Code Description Unit Quantity Rate Amount
Details of cost for 1 sqm
0863 Putty for wood work kilogram 0.68 28.00 19.04
9999 Spirit L.S. 2.73 2.12 5.79
9999 Nails L.S. 7.15 2.12 15.16
LABOUR
0119 Glazier day 0.30 714.00 214.20
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 450.72 W
Add 1 % Water charges on "W" 4.51
TOTAL 455.22 X
Add GST on "X" (multiplying
factor 0.1405) 63.96
TOTAL 519.18 Y
Add 15% CPOH on "Y" 77.88
TOTAL 597.06 Z
Add Cess @ 1% on "Z" 5.97
Add 15 % Contractor's profit and
overheads 603.03
Cost of 1.00 sqm 603.03
Say 603.05
14.11 Fixing old glass panes with wooden fillets (excluding cost of fillets)
Code Description Unit Quantity Rate Amount
Detail of cost for 1 sqm
LABOUR
0119 Glazier day 0.30 714.00 214.20
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 1.43 2.12 3.03
SUB HEAD : 14- REPAIRS TO BUILDING 1103
Code Description Unit Quantity Rate Amount
9999 Nails L.S. 3.90 2.12 8.27
TOTAL 419.00 W
Add 1 % Water charges on "W" 4.19
TOTAL 423.19 X
Add GST on "X" (multiplying
factor 0.1405) 59.46
TOTAL 482.65 Y
Add 15% CPOH on "Y" 72.40
TOTAL 555.04 Z
Add Cess @ 1% on "Z" 5.55
Cost of 1.00 sqm 560.60
Say 560.60
14.12 Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in
existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement
bar, including cleaning, refilling, making good the chase with matching concrete,
plastering and painting the exposed portion of the clamps complete.
Code Description Unit Quantity Rate Amount
Details of cost for each fan clamp.
MATERIAL
M.S.bar 16mm dia = 40cm (including
wastage) @ 1.58 kg/m = 0.632 kg
1003 Mild steel round bar above 12 mm dia quintal 0.00632 4750.00 30.02
9999 Cement concrete 1:2:4 (1 Cement : 2
Coarse sand : 4 graded stone
aggregate 20mm nominal size) mortar
for rendering or plastering L.S. 13.52 2.12 28.66
9999 Painting two or more coats to exposed
portion of the clamp including priming
coat L.S. 7.15 2.12 15.16
Labour for fixing
0102 Blacksmith 1st class day 0.03 784.00 23.52
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 350.08 W
Add 1 % Water charges on "W" 3.50
TOTAL 353.58 X
Add GST on "X" (multiplying
factor 0.1405) 49.68
TOTAL 403.26 Y
Add 15% CPOH on "Y" 60.49
TOTAL 463.75 Z
Add Cess @ 1% on "Z" 4.64
Cost of each 468.38
Say 468.40
SUB HEAD : 14- REPAIRS TO BUILDING 1104
14.13 Regrading terracing of mud phaska covered with tiles or brick, in cement mortar
by dismantling tiles or bricks, removing mud plaster, preparing the surface of
mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or
bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing
unserviceable tiles or bricks with new ones and disposal of unserviceable
material to the dumping ground (the cost of the new tiles or brick excluded), all
complete as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
(i) Dismantling tiles/bricks in cement
mortar including removing mud plaster
and cleaning the tiles/bricks
LABOUR
0155 Mason (average) day 0.54 749.00 404.46
0114 Beldar day 0.54 645.00 348.30
(ii) Preparing the surface, for mud
phuska to proper slope, relaying mud
plaster gobri leeping.
0155 Mason (average) day 0.27 749.00 202.23
25mm thick mud plaster including
gobri leaping
MATERIAL
Mud mortar
3.18 Rate as per Item Number 3.18 of
SH: Mortars cum 0.24 823.15 197.56
0308 Bhusa quintal 0.084 500.00 42.00
Gobri mortar
3.18 Rate as per Item Number 3.18 of
SH: Mortars cum 0.12 823.15 98.78
LABOUR
0114 Beldar day 0.25 645.00 161.25
(iii) relaying tiles/bricks including
Cement mortar 1:3 (1 Cement : 3 fine
sand) for grouting
3.3 Rate as per item No 3.3 of SH: Mortars cum 0.061 4382.15 267.31
LABOUR
0155 Mason (average) day 1.20 749.00 898.80
0114 Beldar day 1.50 645.00 967.50
0101 Bhisti day 1.00 714.00 714.00
9999 Disposal of mulba L.S. 5.33 2.12 11.30
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 4319.27 W
Add 1 % Water charges on "W" 43.19
TOTAL 4362.47 X
Add GST on "X" (multiplying
factor 0.1405) 612.93
TOTAL 4975.39 Y
Add 15% CPOH on "Y" 746.31
TOTAL 5721.70 Z
Add Cess @ 1% on "Z" 57.22
Cost of 10.00 sqm 5778.92
Cost of 1.00 sqm 577.89
Say 577.90
SUB HEAD : 14- REPAIRS TO BUILDING 1105
14.14 Replacing sand stone slabs in roofing, laid in cement mortar 1:4 (1 cement : 4
coarse sand), including necessary repairs and cement pointing with same mortar
complete, including disposal of rubbish to dumping ground, all complete as
per direction of Engineer-in-Charge.
14.14.1 Red/ white sand stone slabs 30 to 50 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
Dismantling existing stone, slabs
roofing 1x10 sqmx0.05m = 0.50 cum.
0114 Beldar day 0.885 645.00 570.83
0115 Coolie day 0.375 645.00 241.88
9999 Sundries L.S. 4.03 2.12 8.54
9999 Cleaning the surface including
necessary repairs L.S. 40.43 2.12 85.71
1174 Red sand stone slab 45 mm and 50 mm
thick (un-dressed) sqm 11.00 260.00 2860.00
2216 Carriage of Stone blocks white &
red sand stone & kota stone slab tonne 1.41 145.72 205.47
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 0.0105 4355.20 45.73
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.0075 4382.15 32.87
0155 Mason (average) day 1.69 749.00 1265.81
0100 Bandhani day 2.03 714.00 1449.42
0115 Coolie day 1.69 645.00 1090.05
0101 Bhisti day 0.34 714.00 242.76
9999 Sundries L.S. 16.12 2.12 34.17
2264 Carriage of Rubbish cum 0.50 163.93 81.97
TOTAL 8215.20 W
Add 1 % Water charges on "W" 82.15
TOTAL 8297.35 X
Add GST on "X" (multiplying
factor 0.1405) 1165.78
TOTAL 9463.12 Y
Add 15% CPOH on "Y" 1419.47
TOTAL 10882.59 Z
Add Cess @ 1% on "Z" 108.83
Cost of 10.00 sqm 10991.42
Cost of 1.00 sqm 1099.14
Say 1099.15
14.15 Renewing wooden battens in roofs, including making good the holes in wall
and painting with oil type wood preservative of approved brand and manufacture
complete, including removal of rubbish to the dumping ground, all complete as
per direction of Engineer-in-Charge.
SUB HEAD : 14- REPAIRS TO BUILDING 1106
14.15.1 Sal wood battens
Code Description Unit Quantity Rate Amount
Details of cost for 10 battens i.e.
300 cudm
3 metres long of 100x100mm
10x3x0.1x0.1 = 0.3cum =300cudm
Add wastage @ 2%= 6 cudm, Total
= 306 cudm
MATERIAL
1199 Sal wood in scantling 10 cudm 30.60 600.00 18360.00
2204 Carriage of Timber cum 0.306 187.35 57.33
LABOUR
Taking out the existing battens and
refixing new one including supporting
the roof
0112 Carpenter 2nd class day 0.50 714.00 357.00
0114 Beldar day 2.00 645.00 1290.00
9999 Disposal of mulba L.S. 5.33 2.12 11.30
9999 Making good the holes including sundries L.S. 80.73 2.12 171.15
0859 Oil type wood preservative litre 1.22 130.00 158.60
0131 Painter day 0.183 714.00 130.66
0115 Coolie day 0.183 645.00 118.04
9977 Carriage L.S. 0.78 2.12 1.65
9999 Brushes L.S. 5.07 2.12 10.75
9999 Sundries L.S. 4.81 2.12 10.20
TOTAL 20676.67 W
Add 1 % Water charges on "W" 206.77
TOTAL 20883.44 X
Add GST on "X" (multiplying
factor 0.1405) 2934.12
TOTAL 23817.56 Y
Add 15% CPOH on "Y" 3572.63
TOTAL 27390.20 Z
Add Cess @ 1% on "Z" 273.90
Cost of 300 Cudm 27664.10
Cost of 1.00 cum 92213.67
Say 92213.65
14.16 Renewing wooden beams in roofs including making good the holes in walls
and painting with oil type wood preservative of approved brand and manufacture
complete, including removal of rubbish to the dumping ground, all complete as
per direction of Engineer-in-Charge.
14.16.1 Not exceeding 4.00 metres in length.
14.16.1.1 Sal wood beams
Code Description Unit Quantity Rate Amount
Details of cost for 300 cudm or 0.3 cum
Consider one beam i.e. 300 cudm.
0.25 x 0.30m x 4.0m (long) = 0.30 cum
Add wastage @ 2% (0.006 cum)
= 0.306 cum =306 cudm
(i) Propping the roof
SUB HEAD : 14- REPAIRS TO BUILDING 1107
Code Description Unit Quantity Rate Amount
MATERIAL
100mm diameter ballies 4m long 10 nos.
100x100mm salwood battens 1.0 metre
long 5 nos.x1.0x0.1x0.1 =0.05cum
= 50 cudm.
These materials can be used for 16
times Hence qty for one operation 1/16
= 3.125 cudm
1199 Sal wood in scantling 10 cudm 0.3125 600.00 187.50
2204 Carriage of Timber cum 0.003125 187.35 0.59
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
(ii) Taking out the existing beams etc.
LABOUR
0155 Mason (average) day 0.13 749.00 97.37
0100 Bandhani day 0.50 714.00 357.00
0114 Beldar day 0.33 645.00 212.85
(iii) Renewal
Materials and Labour
1199 Sal wood in scantling 10 cudm 30.60 600.00 18360.00
2204 Carriage of Timber cum 0.306 187.35 57.33
0112 Carpenter 2nd class day 1.00 714.00 714.00
0100 Bandhani day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
Painting with oil preservative
(4x1.1) +( 2.0x0.25x0.30) =4.4 + 0.15=
4.55 sqm @ 1 litre/10sqm = 0.455 litre
0859 Oil type wood preservative litre 0.455 130.00 59.15
0131 Painter day 0.07 714.00 49.98
0115 Coolie day 0.07 645.00 45.15
9999 Sundries L.S. 0.13 2.12 0.28
9977 Carriage L.S. 1.82 2.12 3.86
9999 Brushes L.S. 1.82 2.12 3.86
9999 Making good the holes L.S. 20.67 2.12 43.82
9999 Sundries L.S. 26.91 2.12 57.05
0302 Safeda ballies 125 mm diameter metre 2.50 40.00 100.00
TOTAL 21691.53 W
Add 1 % Water charges on "W" 216.92
TOTAL 21908.44 X
Add GST on "X" (multiplying
factor 0.1405) 3078.14
TOTAL 24986.58 Y
Add 15% CPOH on "Y" 3747.99
TOTAL 28734.56 Z
Add Cess @ 1% on "Z" 287.35
Cost of 300 Cudm 29021.91
Cost of 1.00 cum 96739.70
Say 96739.70
SUB HEAD : 14- REPAIRS TO BUILDING 1108
14.16.1.2 Hollock wood beams
Code Description Unit Quantity Rate Amount
Details of cost for 300 cudm or 0.3 cum
Consider one beam
0.25 x 0.30m x 4.0m (long) = 0.30 cum
= 300 cudm
Add wastage @ 2% (0.006 cum)
= 0.306 cum =306cudm
(I) Propping the roof
MATERIAL
100mm diameter ballies 4m long 10 nos.
100x100mm hollock wood battens
1.0metre long 5 nos.x1.0x0.1x0.1
=0.05cum = 50 cudm.
These materials can be used for 16
times hence qty for one operation 1/16
= 3.125 cudm
2466 Hollock wood in scantling 10 cudm 0.3125 357.00 111.56
2204 Carriage of Timber cum 0.003125 187.35 0.59
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
(ii) Taking out the existing beams etc.
LABOUR
0155 Mason (average) day 0.13 749.00 97.37
0100 Bandhani day 0.50 714.00 357.00
0114 Beldar day 0.33 645.00 212.85
(iii) Renewal
Materials and Labour
2466 Hollock wood in scantling 10 cudm 30.60 357.00 10924.20
2204 Carriage of Timber cum 0.306 187.35 57.33
0112 Carpenter 2nd class day 1.00 714.00 714.00
0100 Bandhani day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
Painting with oil preservative
(4x1.1) + (2.0x0.25x0.30) =4.4 + 0.15=
4.55 sqm @ 1 litre/10sqm = 0.455 litre
0859 Oil type wood preservative litre 0.455 130.00 59.15
0131 Painter day 0.07 714.00 49.98
0115 Coolie day 0.07 645.00 45.15
9999 Sundries L.S. 0.13 2.12 0.28
9977 Carriage L.S. 1.82 2.12 3.86
9999 Brushes L.S. 1.82 2.12 3.86
9999 Making good the holes L.S. 20.67 2.12 43.82
9999 Sundries L.S. 26.91 2.12 57.05
0302 Safeda ballies 125 mm diameter metre 2.50 40.00 100.00
TOTAL 14179.79 W
Add 1 % Water charges on "W" 141.80
TOTAL 14321.59 X
Add GST on "X" (multiplying
factor 0.1405) 2012.18
TOTAL 16333.77 Y
Add 15% CPOH on "Y" 2450.07
TOTAL 18783.84 Z
Add Cess @ 1% on "Z" 187.84
Cost of 300 Cudm 18971.67
Cost of 1.00 cum 63238.90
Say 63238.90
SUB HEAD : 14- REPAIRS TO BUILDING 1109
14.16.2 Above 4.00 metres and upto 5.00 metres length.
14.16.2.1 Sal wood beams
Code Description Unit Quantity Rate Amount
Details of cost for 375 cudm or
0.375 cum
Consider one beam i.e. 375 cudm.
0.25 x 0.30m x 5.0m (long) = 0.375 cum
Add wastage @ 2% (0.008 cum)
= 0.383 cum = 383cudm
(i) Propping the roof
MATERIAL
125mm diameter ballies 5m long 12 nos
100x100mm salwood battens 1.0 metre
long 6 nos. x1.0x0.1x0.1 = 60 cudm.
These materials can be used for 16
times hence qty for one operation 1/16
= 3.75 cudm
1199 Sal wood in scantling 10 cudm 0.375 600.00 225.00
2204 Carriage of Timber cum 0.00375 187.35 0.70
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
(ii) Taking out the existing beams etc.
LABOUR
0155 Mason (average) day 0.25 749.00 187.25
0100 Bandhani day 0.63 714.00 449.82
0114 Beldar day 0.50 645.00 322.50
(iii) Renewal
Materials and Labour
1199 Sal wood in scantling 10 cudm 38.30 600.00 22980.00
2204 Carriage of Timber cum 0.383 187.35 71.76
0112 Carpenter 2nd class day 1.00 714.00 714.00
0100 Bandhani day 1.00 714.00 714.00
0114 Beldar day 2.00 645.00 1290.00
Painting with oil preservative
(2x5x0.25)+3.0 + 2.0x0.25x0.30
= 5.5 + 0.15 = 5.65 sqm @ 1 litre/
10sqm = 0.565 litre
0859 Oil type wood preservative litre 0.565 130.00 73.45
0131 Painter day 0.08 714.00 57.12
0115 Coolie day 0.08 645.00 51.60
9999 Sundries L.S. 0.26 2.12 0.55
9977 Carriage L.S. 2.34 2.12 4.96
9999 Brushes L.S. 2.21 2.12 4.69
9999 Making good the holes L.S. 20.67 2.12 43.82
9999 Sundries L.S. 33.15 2.12 70.28
0302 Safeda ballies 125 mm diameter metre 3.75 40.00 150.00
TOTAL 27751.24 W
Add 1 % Water charges on “W” 277.51
TOTAL 28028.76 X
Add GST on “X” (multiplying
factor 0.1405) 3938.04
TOTAL 31966.80 Y
Add 15% CPOH on “Y” 4795.02
TOTAL 36761.82 Z
Add Cess @ 1% on “Z” 367.62
Cost of 375 Cudm 37129.43
Cost of 1.00 cum 99011.81
Say 99011.80
SUB HEAD : 14- REPAIRS TO BUILDING 1110
14.16.2.2 Hollock wood beams
Code Description Unit Quantity Rate Amount
Details of cost for 375 cudm or
0.375 cum
Consider one beam i.e. 375 cudm.
0.25 x 0.30m x 5.0m (long) = 0.375 cum
Add wastage @ 2% (0.008 cum)
= 0.383 cum = 383cudm
(i) Propping the roof
MATERIAL
125mm diameter ballies 5m long 12 nos
100x100mm hollock wood battens
1.0 metre long 6 nos. x1.0x0.1x0.1
= 60 cudm.
These materials can be used for
16 times hence qty for one operation
1/16 = 3.75 cudm
2466 Hollock wood in scantling 10 cudm 0.375 357.00 133.88
2204 Carriage of Timber cum 0.0375 187.35 7.03
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
(ii) Taking out the existing beams etc.
LABOUR
0155 Mason (average) day 0.25 749.00 187.25
0100 Bandhani day 0.63 714.00 449.82
0114 Beldar day 0.50 645.00 322.50
(iii) Renewal
Materials and Labour
2466 Hollock wood in scantling 10 cudm 38.30 357.00 13673.10
2204 Carriage of Timber cum 0.383 187.35 71.76
0112 Carpenter 2nd class day 1.00 714.00 714.00
0100 Bandhani day 1.00 714.00 714.00
0114 Beldar day 2.00 645.00 1290.00
Painting with oil preservative
(2x5x0.25)+3.0 + 2.0x0.25x0.30
= 5.5 + 0.15 = 5.65 sqm @ 1 litre/
10sqm = 0.565 litre
0859 Oil type wood preservative litre 0.565 130.00 73.45
0131 Painter day 0.08 714.00 57.12
0115 Coolie day 0.08 645.00 51.60
9999 Sundries L.S. 0.26 2.12 0.55
9977 Carriage L.S. 2.34 2.12 4.96
9999 Brushes L.S. 2.21 2.12 4.69
9999 Making good the holes L.S. 20.67 2.12 43.82
9999 Sundries L.S. 33.15 2.12 70.28
0302 Safeda ballies 125 mm diameter metre 3.75 40.00 150.00
TOTAL 18359.54 W
Add 1 % Water charges on "W" 183.60
TOTAL 18543.14 X
Add GST on "X" (multiplying
factor 0.1405) 2605.31
TOTAL 21148.45 Y
Add 15% CPOH on "Y" 3172.27
TOTAL 24320.71 Z
Add Cess @ 1% on "Z" 243.21
Cost of 375 Cudm 24563.92
Cost of 1.00 cum 65503.79
Say 65503.80
SUB HEAD : 14- REPAIRS TO BUILDING 1111
14.17 Raking out joints in lime or cement mortar and preparing the surface for re-
pointing or replastering, including disposal of rubbish to the dumping ground,
all complete as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 0.53 645.00 341.85
0115 Coolie day 0.08 645.00 51.60
0101 Bhisti day 0.07 714.00 49.98
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 446.46 W
Add 1 % Water charges on "W" 4.46
TOTAL 450.93 X
Add GST on "X" (multiplying
factor 0.1405) 63.36
TOTAL 514.28 Y
Add 15% CPOH on "Y" 77.14
TOTAL 591.42 Z
Add Cess @ 1% on "Z" 5.91
Cost of 10.00 sqm 597.34
Cost of 1.00 sqm 59.73
Say 59.75
14.18 Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of
integral water proofing compound by weight of cement for flat tile bricks on
top of mud phaska :
14.18.1 With F.P.S. brick tiles
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.015 4382.15 65.73
1213 Water proofing materials kilogram 0.153 35.00 5.36
2% of wt. of cement
LABOUR
0115 Coolie day 0.36 645.00 232.20
0124 Mason (brick layer) 2nd class day 0.36 714.00 257.04
0101 Bhisti day 0.36 714.00 257.04
9999 Sundries L.S. 18.85 2.12 39.96
TOTAL 857.33 W
Add 1 % Water charges on "W" 8.57
TOTAL 865.90 X
Add GST on "X" (multiplying
factor 0.1405) 121.66
TOTAL 987.56 Y
Add 15% CPOH on "Y" 148.13
TOTAL 1135.70 Z
Add Cess @ 1% on "Z" 11.36
Cost of 10.00 sqm 1147.05
Cost of 1.00 sqm 114.71
Say 114.70
SUB HEAD : 14- REPAIRS TO BUILDING 1112
14.18.2 With modular brick tiles
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Cement mortar 1 : 3 (1 cement :
3 fine sand)
3.3 Rate as per Item Number 3.3 of
SH: Mortars cum 0.017 4382.15 74.50
1213 Water proofing materials kilogram 0.173 35.00 6.06
2% of wt. of cement
LABOUR
0115 Coolie day 0.36 645.00 232.20
0124 Mason (brick layer) 2nd class day 0.36 714.00 257.04
0101 Bhisti day 0.36 714.00 257.04
9999 Sundries L.S. 18.85 2.12 39.96
TOTAL 866.79 W
Add 1 % Water charges on “W” 8.67
TOTAL 875.46 X
Add GST on “X” (multiplying
factor 0.1405) 123.00
TOTAL 998.46 Y
Add 15% CPOH on “Y” 149.77
TOTAL 1148.23 Z
Add Cess @ 1% on “Z” 11.48
Cost of 10.00 sqm 1159.72
Cost of 1.00 sqm 115.97
Say 115.95
14.19 Taking out wind ties from roof including cutting out rusted bolts, nuts etc. and
removing materials to any distance within compound and stacking.
Code Description Unit Quantity Rate Amount
Details of cost for 30 mtrs of
weight 63 kgs
M.S. Flats 40x6mm @ 1.9kg./m
= 30x1.9 = 57 kg. (A)
J' hook bolts @ 30cm centre to centre
= 101 Nos. x 0.15 m = 15.15 m @
0.40kg./ m = 6.06kg (B)
Total (A+B) = 63.06 kg Say 63 kg
LABOUR
0103 Blacksmith 2nd class day 0.09 714.00 64.26
0100 Bandhani day 0.06 714.00 42.84
0114 Beldar day 0.16 645.00 103.20
TOTAL 210.30 W
Add 1 % Water charges on "W" 2.10
TOTAL 212.40 X
Add GST on "X" (multiplying
factor 0.1405) 29.84
TOTAL 242.25 Y
Add 15% CPOH on "Y" 36.34
TOTAL 278.58 Z
Add Cess @ 1% on "Z" 2.79
Cost for 63 kg. 281.37
Cost of 1.00 kg 4.47
Say 4.45
SUB HEAD : 14- REPAIRS TO BUILDING 1113
14.20 Fixing of old wind tie with new fittings including painting two or more coats
with anticorrosive bitumastic paint of approved brand & manufacturer over and
including priming coat of ready mixed zinc chromate yellow primer of approved
brand.
Code Description Unit Quantity Rate Amount
Detail of cost for 20.2 m wind tie
MATERIAL
1023 Galvanised steel J or L hooks 8 mm dia 10 Nos 6.80 120.00 816.00
@ 30 cm center to center = 68 Nos
1208 Bitumen washer 100 Nos 0.68 30.00 20.40
1209 G.I. plain washer thick 100 Nos 0.68 35.00 23.80
9977 Carriage of bolts, nuts and washers etc. L.S. 1.17 2.12 2.48
LABOUR
0102 Blacksmith 1st class day 0.34 784.00 266.56
0114 Beldar day 0.34 645.00 219.30
9999 Sundries L.S. 13.91 2.12 29.49
Applying priming coat with ready mixed
zink chromate yellow primer
20.2x2x(0.04+0.006) = 1.86 sqm
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 1.86 55.50 103.23 A
Painting with ready mixed black
antcorrosive bitumastic paint
13.65.1 Rate as per item No.13.65.1
SH: Finishing sqm 1.86 115.10 214.09 A
TOTAL 1695.35 W
Add 1 % Water charges on “W-A” 13.78
TOTAL 1709.13 X
Add GST on “X-A” (multiplying
factor 0.1405) 195.55
TOTAL 1904.68 Y
Add 15% CPOH on “Y-A” 238.10
TOTAL 2142.78 Z
Add Cess @ 1% on “Z-A” 18.25
Cost of 20.2 metres 2161.03
Cost of 1.00 metre 106.98
Say 107.00
14.21 Renewing bottom rail and/or top runner of collapsible gate including making
good all damages and applying priming coat of zinc chromate yellow primer of
approved brand and manufacturer.
Code Description Unit Quantity Rate Amount
Detail of cost for gate of size 1.52x2.4 m
(weight 11.55 kg)
MATERIAL
M.S. Tee 40x40x6 mm
Top rail = 1.725 m
Bottom rail = 1.570 m
Total = 3.295 m say 3.30 m @ 3.5 kg/m
= 11.55 kg
Add 10% wastage = 1.155 kg
Total = 12.705 kg = 0.1270 q say 0.13 q
SUB HEAD : 14- REPAIRS TO BUILDING 1114
Code Description Unit Quantity Rate Amount
1007 Structurals such as tees,angles
channels and R.S. joists quintal 0.13 4950.00 643.50
2205 Carriage of Steel tonne 0.013 145.72 1.89
Taking out collapsible gate including
frame
15.12.2 (Rate as per item no 15.12.2 of
SH Dismantling and Demolishing) each 1.00 414.55 414.55 A
Refixing of collapsible gate including
mending good the demaged floor, wall
etc.frame
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.03 8843.45 265.30 A
3.6 Cement mortar 1 : 6 (1 cement : 6 fine
sand) (Rate as per item No 3.6) cum 0.01 3044.30 30.44
9999 Cement concrete 1:2:4 filled in chase
cut L.S. 24.18 2.12 51.26
9999 Disposal of mulba L.S. 1.82 2.12 3.86
Priming coat on Tees 0.16x3.3
= 0.53 sqm
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 0.53 55.50 29.42 A
LABOUR
Labour for fixing the gate
0155 Mason (average) day 0.50 749.00 374.50
0114 Beldar day 0.75 645.00 483.75
9999 Sundries L.S. 2.60 2.12 5.51
TOTAL 2303.99 W
Add 1 % Water charges on "W-A" 15.95
TOTAL 2319.94 X
Add GST on "X-A" (multiplying
factor 0.1405) 226.30
TOTAL 2546.23 Y
Add 15% CPOH on "Y-A" 275.54
TOTAL 2821.78 Z
Add Cess @ 1% on "Z-A" 21.13
Cost of 11.55 kg 2842.90
Cost of 1.00 kg 246.14
Say 246.15
14.22 Renewing Wrought iron or M.S. Wheel or roller of steel door or gate and fitting
and fixing the same with necessary clamps, nuts and bolts/welding and erection
etc. complete.
14.22.1 Wheel 50 mm dia and below
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos wheels of
40 mm dia.
MATERIAL
Weight of 10 nos wheels
SUB HEAD : 14- REPAIRS TO BUILDING 1115
Code Description Unit Quantity Rate Amount
10x[3.14x{(4/2)x(4/2)}x4]x7.850/1000
= 3.94 kg
Weight of 10 nos clamps 6 mm thick
=10x lenth of clamp =10x0.17m @
1.90kg/m =3.23 kg
Weight of 10 nos 10 mm dia. Bolts, 10
cm long 10x0.10m = 1m @ 0.60 kg/m
= 0.60 kg. Total = 7.70 kg say 8 kg
Labour for dismantling :
0103 Blacksmith 2nd class day 0.01 714.00 7.14
0100 Bandhani day 0.01 714.00 7.14
0114 Beldar day 0.02 645.00 12.90
9999 Sundries L.S. 0.39 2.12 0.83
Renewing the wheels with clamps :-
MATERIAL
7442 Wheel 75 mm dia. 40 mm wide each 10.00 62.00 620.00
10 nos clamps out of M.S. flat 40x6
mm, 170 mm long = 10x0.17m =
1.70m @ 1.9 kg/m = 3.23 kg
Add 5% wastage = 0.16 kg
Total = 3.39 kg say 3.50 kg
1008 Flats upto 10 mm in thickness quintal 0.035 4850.00 169.75
M.S. bolt/pin 10 mm dia 10 cm long
10 Nos
10x0.06 = 0.6 kg = 0.006 q
1034 Bolts and nuts upto 300 mm in length quintal 0.006 5200.00 31.20
1215 Welding by electric plant cm 80.00 2.00 160.00
length = 10x(2x4) = 80cm
LABOUR
Labour for cutting, assembling and
errection charges
0102 Blacksmith 1st class day 0.03 784.00 23.52
0100 Bandhani day 0.02 714.00 14.28
0114 Beldar day 0.11 645.00 70.95
Priming coat : =
10x2(0.06+0.008)x0.25m = 0.34 sqm
on Tees 0.16x3.3 = 0.53 sqm
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 0.165 55.50 9.16 A
9999 Sundries L.S. 1.69 2.12 3.58
TOTAL 1130.45 W
Add 1 % Water charges on "W-A" 11.21
TOTAL 1141.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 159.12
TOTAL 1300.78 Y
Add 15% CPOH on "Y-A" 193.74
TOTAL 1494.52 Z
Add Cess @ 1% on "Z-A" 14.85
Cost of 10 nos wheels 1509.37
Cost per wheel 150.94
Say 150.95
SUB HEAD : 14- REPAIRS TO BUILDING 1116
14.22.2 Wheel above 50 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos wheels
Considering average wheel dia =75 mm
Width of wheel = 40 mm
M.S. flat for clamp = 60x8 mm
Bolt size 16 mm dia.
Lenth of one clamp :
2x(0.04+0.0375+0.02)+0.05 =0.195+
0.05=0.245m say 0.25m
MATERIAL
Weight of 10 nos wheels
10x[3.14x{(7.5/2)x(7.5/2)}x4]x7.850/
1000= 13.87 kg
Weight of 10 nos clamps 8 mm thick
=10x0.25 m @ 3.8kg/m = 9.50 kg
Weight of 10 nos 16 mm dia. Bolts,
10 cm long 10x0.10 m @ 1.60 kg/m
= 1.60 kg
Total = 24.97 kg say 25 kg
Labour for dismantling :
0103 Blacksmith 2nd class day 0.04 714.00 28.56
0100 Bandhani day 0.03 714.00 21.42
0114 Beldar day 0.06 645.00 38.70
9999 Sundries L.S. 1.04 2.12 2.20
Renewing the wheels with clamps :-
MATERIAL
7442 Wheel 75 mm dia. 40 mm wide each 10.00 62.00 620.00
10 nos clamps out of M.S. flat
60x8 mm = 10x0.25 m @ 3.8 kg/m
= 9.5 kg
Add 5% wastage = 0.48 kg
Total = 9.98 kg say 10 kg
1008 Flats upto 10 mm in thickness quintal 0.10 4850.00 485.00
M.S. bolt/pin 16 mm dia 10 cm
long 10 Nos
10x0.16= 1.6 kg = 0.016 q
1034 Bolts and nuts upto 300 mm in length quintal 0.016 5200.00 83.20
1215 Welding by electric plant cm 120.00 2.00 240.00
length = 10x(2x6)
LABOUR
Labour for cutting, assembling and
errection charges
0102 Blacksmith 1st class day 0.10 784.00 78.40
0100 Bandhani day 0.05 714.00 35.70
0114 Beldar day 0.36 645.00 232.20
Priming coat : = 10x2(0.06+0.008)x
0.25m = 0.34 sqm on Tees 0.16x
3.3 = 0.53 sqm
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 0.34 55.50 18.87 A
SUB HEAD : 14- REPAIRS TO BUILDING 1117
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 1895.55 W
Add 1 % Water charges on "W-A" 18.77
TOTAL 1914.32 X
Add GST on "X-A" (multiplying
factor 0.1405) 266.31
TOTAL 2180.63 Y
Add 15% CPOH on "Y-A" 324.26
TOTAL 2504.90 Z
Add Cess @ 1% on "Z-A" 24.86
Cost of 10 nos wheels 2529.76
Cost per wheel 252.98
Say 253.00
14.23 Pumping out water caused by springs, tidal or river seepage, broken water mains
or drains and the like.
Code Description Unit Quantity Rate Amount
Details for 10.91 kilolitre
Pumping hours 3 hrs. or 0.375 days
0011 Hire charges of Pumpset of capacity
4000 litres/hour. day 0.375 700.00 262.50
0114 Beldar day 2.00 645.00 1290.00
for clearing slush
TOTAL 1552.50 W
Add 1 % Water charges on "W" 15.53
TOTAL 1568.03 X
Add GST on "X" (multiplying
factor 0.1405) 220.31
TOTAL 1788.33 Y
Add 15% CPOH on "Y" 268.25
TOTAL 2056.58 Z
Add Cess @ 1% on "Z" 20.57
Cost of 10.91 kilolitre 2077.15
Cost of 1 kilolitre 190.39
Say 190.40
14.24 Mud mortar made with local clay good earth.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
MATERIAL
0811 Mud (dry) cum 1.08 165.00 178.20
LABOUR
0114 Beldar day 0.63 645.00 406.35
0101 Bhisti day 0.315 714.00 224.91
9999 Sundries L.S. 6.45 2.12 13.67
TOTAL 823.13
Cost of 1 cum 823.13
Say 823.15
SUB HEAD : 14- REPAIRS TO BUILDING 1118
14.25 Brick work with common burnt clay bricks of class designation 7.5 in mud mortar
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2602 Common burnt clay F.P.S. (non
modular) bricks class designation 7.5 1000 Nos 0.494 4590.00 2267.46
Mud mortar
3.18 Rate as per Item Number 3.18 of
SH: Mortars cum 0.25 823.15 205.79
2201 Carriage of Bricks 1000 Nos 0.494 437.15 215.95
9999 Sundries L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.36 784.00 282.24
0124 Mason (brick layer) 2nd class day 0.36 714.00 257.04
0115 Coolie day 1.37 645.00 883.65
0101 Bhisti day 0.2 714.00 142.80
TOTAL 4260.72 W
Add 1 % Water charges on "W" 42.61
TOTAL 4303.32 X
Add GST on "X" (multiplying
factor 0.1405) 604.62
TOTAL 4907.94 Y
Add 15% CPOH on "Y" 736.19
TOTAL 5644.13 Z
Add Cess @ 1% on "Z" 56.44
Cost of 1 Cum. 5700.57
Say 5700.55
14.26 Providing and fixing 25 mm thick shutters for cup board etc. :
14.26.1 Panelled or panelled & glazed shutters :
14.26.1.1 Superior class teak wood including nickel plated bright finished M.S. piano
hinges with necessary screws.
Code Description Unit Quantity Rate Amount
Details of cost for shutter of cup-
board 200x108cm = 2.16 sqm.
MATERIAL
Styles
4x200x8.0x2.5cm = 0.016 cum+
Rails
Top rail
1x110.5x8.0x2.5cm = 0.0022cum+
Lock and bottom rails
2x110.5x8.0x2.5 cm = 0.0044 cum
Panels
2x48x41x1.6cm = 0.006cum+
Sash bars
2x114x3.8x2.5cm = 0.0022cum+
6x48x3.8x2.5cm = 0.003 cum+
Beading
16x92x1.4x1.2cm = 0.002cum
Total = 0.0358 cum
Add for wastage @ 10% = 0.00336 cum.
Grand Total = 0.0394 cum = 39.40 cudm
say 39 cudm
SUB HEAD : 14- REPAIRS TO BUILDING 1119
Code Description Unit Quantity Rate Amount
1186 Superior class teak wood such as
Dandeli, Balarshah or Malabar in
planks 10 cudm 3.90 1100.00 4290.00
2204 Carriage of Timber cum 0.04 187.35 7.49
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 0.99 309.00 305.91
Fittings-
0608 Nickel plated mild steel piono hinges
1 mm thick 25 mm wide metre 4.00 39.00 156.00
0639 Bright finished or black enamelled mild
steel screws 25 mm 100 Nos 1.20 40.00 48.00
LABOUR
0111 Carpenter 1st class day 2.40 784.00 1881.60
0119 Glazier day 0.18 714.00 128.52
0114 Beldar day 0.77 645.00 496.65
9999 Sundries L.S. 40.43 2.12 85.71
TOTAL 7399.89 W
Add 1 % Water charges on "W" 74.00
TOTAL 7473.88 X
Add GST on "X" (multiplying
factor 0.1405) 1050.08
TOTAL 8523.97 Y
Add 15% CPOH on "Y" 1278.59
TOTAL 9802.56 Z
Add Cess @ 1% on "Z" 98.03
Cost of 2.16 sqm. 9900.59
Cost of 1 sqm. 4583.60
Say 4583.60
14.26.1.2 Ist class teak wood including nickel plated bright finished M.S. piano hinges
with necessary screws.
Code Description Unit Quantity Rate Amount
Details of cost for shutters of a cup-
board (half glazed and half panelled)
200x108cm= 2.16 sqm.
MATERIAL
Styles
4x200x8.0x2.5cm = 0.016 cum+
Rails
Top rail
1x110.5x8.0x2.5cm = 0.0022cum+
Lock and bottom rail
2x110.5x8.0x2.5cm = 0.0044 cum.
Panels
2x48x41x1.6cm = 0.006cum+
Sash bars
2x114x3.8x2.5cm = 0.0022 cum+
6x48x3.8x2.5cm = 0.003 cum+
Beading
16x92x1.4x1.2cm = 0.002cum
Total = 0.0358
SUB HEAD : 14- REPAIRS TO BUILDING 1120
Code Description Unit Quantity Rate Amount
Add for wastage @ 10% = 0.0036 cum.
Grand Total = 0.0394 cum = 39.40 cudm
say 39 cudm
1188 First class teak wood in planks 10 cudm 3.90 850.00 3315.00
2204 Carriage of Timber cum 0.04 187.35 7.49
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 0.99 309.00 305.91
Fittings
0608 Nickel plated mild steel piono hinges
1 mm thick 25 mm wide metre 4.00 39.00 156.00
0639 Bright finished or black enamelled mild
steel screws 25 mm 100 Nos 1.20 40.00 48.00
LABOUR
0111 Carpenter 1st class day 2.40 784.00 1881.60
0119 Glazier day 0.18 714.00 128.52
0114 Beldar day 0.77 645.00 496.65
9999 Sundries L.S. 40.43 2.12 85.71
TOTAL 6424.89 W
Add 1 % Water charges on "W" 64.25
TOTAL 6489.13 X
Add GST on "X" (multiplying
factor 0.1405) 911.72
TOTAL 7400.86 Y
Add 15% CPOH on "Y" 1110.13
TOTAL 8510.99 Z
Add Cess @ 1% on "Z" 85.11
Cost of 2.16 sqm. 8596.10
Cost of 1 sqm. 3979.67
Say 3979.65
14.26.2 Glazed shutters :
14.26.2.1 Superior class teak wood including nickel plated bright finished M.S. piano
hinges with necessary screws.
Code Description Unit Quantity Rate Amount
Details of cost for shutter of cup-board
200x108cm = 2.16 sqm.
MATERIAL
(i) Superior class teak wood
Styles : 4x200x9.5x2.5 cm = 0.019 cum
Rails
Top & intermediate rails
2x110.5x9.5x2.5 cm = 0.005 cum
Lock and bottom rails
2x110.5x19.7x2.5 cm = 0.011 cum
Beadings-
2x186.1x1.9x1.2cm = 0.001cum+
4x171.70x1.9x1.2cm = 0.002cum.
Total = 0.038 cum.
Add for wastage @ 10% = 0.0038 cum.
Grand Total = 0.0418 cum = 42 cudm
SUB HEAD : 14- REPAIRS TO BUILDING 1121
Code Description Unit Quantity Rate Amount
1186 Superior class teak wood such as
Dandeli,Balarshah or Malabar in planks 10 cudm 4.20 1100.00 4620.00
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.27 309.00 392.43
0608 Nickel plated mild steel piono hinges
1 mm thick 25 mm wide metre 4.00 39.00 156.00
75x45x3.2 mm
0639 Bright finished or black enamelled mild
steel screws 25 mm 100 Nos 1.20 40.00 48.00
0597 Bright finished or black enamelled mild
steel butt hinges50x37x1.50 mm 10 Nos 0.20 49.00 9.80
0640 Bright finished or black enamelled mild
steel screws 20 mm 100 Nos 0.08 35.00 2.80
2204 Carriage of Timber cum 0.042 187.35 7.87
LABOUR
0156 Carpenter (average) day 1.83 749.00 1370.67
0119 Glazier day 0.23 714.00 164.22
0114 Beldar day 0.77 645.00 496.65
9999 Sundries L.S. 40.43 2.12 85.71
TOTAL 7354.15 W
Add 1 % Water charges on "W" 73.54
TOTAL 7427.69 X
Add GST on "X" (multiplying
factor 0.1405) 1043.59
TOTAL 8471.28 Y
Add 15% CPOH on "Y" 1270.69
TOTAL 9741.97 Z
Add Cess @ 1% on "Z" 97.42
Cost of 2.16 sqm. 9839.39
Cost of 1 sqm. 4555.28
Say 4555.30
14.26.2.2 Ist class teak wood including nickel plated bright finished M.S. piano hinges
with necessary screws.
Code Description Unit Quantity Rate Amount
Details of cost for shutter of cup-board
200x108cm = 2.16 sqm.
MATERIAL
(i) Teak wood first class
Styles : 4x200x9.5x2.5 cm = 0.019 cum
Rails
Top & intermediate rails
2x110.5x9.5x2.5 cm = 0.005 cum
Lock and bottom rails
2x110.5x19.7x2.5 cm = 0.011 cum
Beadings-
2x186.1x1.9x1.2cm = 0.001cum+
4x171.70x1.9x1.2cm = 0.002cum.
Total = 0.038 cum.
Add for wastage @ 10% = 0.0038 cum.
Grand Total = 0.0418 cum = 42 cudm
1188 First class teak wood in planks 10 cudm 4.20 850.00 3570.00
SUB HEAD : 14- REPAIRS TO BUILDING 1122
Code Description Unit Quantity Rate Amount
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.27 309.00 392.43
0608 Nickel plated mild steel piono hinges
1 mm thick 25 mm wide metre 4.00 39.00 156.00
75x45x3.2 mm
0639 Bright finished or black enamelled mild
steel screws 25 mm 100 Nos 1.20 40.00 48.00
0597 Bright finished or black enamelled mild
steel butt hinges50x37x1.50 mm 10 Nos 0.20 49.00 9.80
0640 Bright finished or black enamelled mild
steel screws 20 mm 100 Nos 0.08 35.00 2.80
2204 Carriage of Timber cum 0.042 187.35 7.87
LABOUR
0156 Carpenter (average) day 1.83 749.00 1370.67
0119 Glazier day 0.23 714.00 164.22
0114 Beldar day 0.77 645.00 496.65
9999 Sundries L.S. 40.43 2.12 85.71
TOTAL 6304.15 W
Add 1 % Water charges on “W” 63.04
TOTAL 6367.19 X
Add GST on “X” (multiplying
factor 0.1405) 894.59
TOTAL 7261.78 Y
Add 15% CPOH on “Y” 1089.27
TOTAL 8351.05 Z
Add Cess @ 1% on “Z” 83.51
Cost of 2.16 sqm. 8434.56
Cost of 1 sqm. 3904.89
Say 3904.90
14.27 Providing and fixing plain jaffri door and window shutters including bright or/
and black enamelled M.S. butt hinges with necessary screws 35x10 mm laths
placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm
beading complete with :
14.27.1 Second class teak wood
Code Description Unit Quantity Rate Amount
Details of cost of a jaffri shutter
176x86 cm = 1.51 sqm
MATERIAL
Teak wood 2nd class
Styles 2x176x7.5x3.5 cm = 0.0092 cum
Rails 3x86x7.5x3.5 = 0.0068 cum
Total 0.0160 cum
Add wastage @ 10 % =0.0016 cum
Total = 0.0176 cum Say 18 cudm
1190 Second class teak wood in planks 10 cudm 1.80 791.00 1423.80
2204 Carriage of Timber cum 0.018 187.35 3.37
Palain Jaffri work
9.41.1 Rate as per Item Number 9.41.1 of
SH:Wood and PVC work sqm 1.51 2622.20 3959.52 A
0595 Bright finished or black enamelled mild
steel butt hinges 100x58x1.90 mm 10 Nos 0.60 80.00 48.00
SUB HEAD : 14- REPAIRS TO BUILDING 1123
Code Description Unit Quantity Rate Amount
0597 Bright finished or black enamelled mild
steel butt hinges50x37x1.50 mm 10 Nos 0.20 49.00 9.80
0637 Bright finished or black enamelled mild
steel screws 40 mm 100 Nos 0.48 60.00 28.80
0640 Bright finished or black enamelled mild
steel screws 20 mm 100 Nos 0.08 35.00 2.80
LABOUR
For making frame and fixing fitting
0112 Carpenter 2nd class day 0.30 714.00 214.20
TOTAL 5690.29 W
Add 1 % Water charges on "W-A" 17.31
TOTAL 5707.60 X
Add GST on "X-A" (multiplying
factor 0.1405) 245.61
TOTAL 5953.21 Y
Add 15% CPOH on "Y-A" 299.05
TOTAL 6252.26 Z
Add Cess @ 1% on "Z-A" 22.93
Cost of 1.51 sqm. 6275.19
Cost of 1 sqm. 4155.75
Say 4155.75
14.28 Providing and fixing brass curtain rods of wall thickness 1.25 mm with two
brass brackets fixed with brass screws and wooden plugs etc. wherever
necessary complete.
14.28.1 20 mm diameter.
Code Description Unit Quantity Rate Amount
Detail of cost for 2 metre long
MATERIAL
0444 Brass curtain rod 20 mm dia 1.25 mm
thick metre 2.00 140.00 280.00
0446 Brass brackets (curtain rods) 20 mm each 2.00 45.00 90.00
9999 Screws L.S. 2.73 2.12 5.79
9977 Carriage L.S. 1.56 2.12 3.31
Wooden plugs including cutting brick
work and fixing in cement mortar
8.23 Rate as per item no 9.32 of
SH : Wood work each 2.00 35.50 71.00 A
9999 LABOUR L.S. 2.73 2.12 5.79
9999 Sundries L.S. 1.56 2.12 3.31
TOTAL 459.19 W
Add 1 % Water charges on “W-A” 3.88
TOTAL 463.07 X
Add GST on “X-A” (multiplying
factor 0.1405) 55.09
TOTAL 518.16 Y
Add 15% CPOH on “Y-A” 67.07
TOTAL 585.23 Z
Add Cess @ 1% on “Z-A” 5.14
Cost of 2 metres 590.37
Cost of 1 metre 295.19
Say 295.20
SUB HEAD : 14- REPAIRS TO BUILDING 1124
14.28.2 25 mm diameter.
Code Description Unit Quantity Rate Amount
Detail of cost for 2 metre long
MATERIAL
0445 Brass curtain rod 25 mm dia
1.25 mm thick metre 2.00 190.00 380.00
0446 Brass brackets (curtain rods) 20 mm each 2.00 45.00 90.00
9999 Screws L.S. 2.73 2.12 5.79
9977 Carriage L.S. 1.56 2.12 3.31
Wooden plugs including cutting brick
work and fixing in cement mortar
8.23 Rate as per item no 9.32 of
SH : Wood work each 2.00 35.50 71.00 A
9999 LABOUR L.S. 2.73 2.12 5.79
9999 Sundries L.S. 1.56 2.12 3.31
TOTAL 559.19 W
Add 1 % Water charges on "W-A" 4.88
TOTAL 564.07 X
Add GST on "X-A" (multiplying
factor 0.1405) 69.28
TOTAL 633.35 Y
Add 15% CPOH on "Y-A" 84.35
TOTAL 717.70 Z
Add Cess @ 1% on "Z-A" 6.47
Cost of 2 metres 724.17
Cost of 1 metre 362.08
Say 362.10
14.29 Providing and fixing M.S. round or square bars with M.S. flats at required spacing
in wooden frames of windows and clerestory windows.
Code Description Unit Quantity Rate Amount
Details of cost for 33.67 kg
Details of cost for window -140x110cm
MATERIAL
M.S. bar 16 mm dia 13x136 cm
= 17.68 m @ 1.58 kg/m = 27.93 kg
Add for wastage @ 10% =2.79 kg
Total = 30.72 kg or 0.307 q
1003 Mild steel round bar above 12 mm dia quintal 0.307 4750.00 1458.25
M.S. flat 40x6mm 2x96cm = 192cm+
1x110cm = 110cm
= 302cm+
Add wastage @ 10% = 30cm
Total = 332cm.@ 1.90 kg/m = 6.31 kg
Say 0.063 q
1008 Flats upto 10 mm in thickness quintal 0.063 4850.00 305.55
2205 Carriage of Steel tonne 0.037 145.72 5.39
(0.307+0.063 = 0.37 q = 0.037 t)
9999 Sundries L.S. 26.91 2.12 57.05
LABOUR
0103 Blacksmith 2nd class day 0.35 714.00 249.90
0112 Carpenter 2nd class day 0.20 714.00 142.80
SUB HEAD : 14- REPAIRS TO BUILDING 1125
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.45 645.00 290.25
TOTAL 2509.19 W
Add 1 % Water charges on "W" 25.09
TOTAL 2534.28 X
Add GST on "X" (multiplying
factor 0.1405) 356.07
TOTAL 2890.35 Y
Add 15% CPOH on "Y" 433.55
TOTAL 3323.90 Z
Add Cess @ 1% on "Z" 33.24
Cost of 33.67 kg.(5.74+27.93=33.67kg) 3357.14
Cost of 1 kg. 99.71
Say 99.70
14.30 Providing joists (karries) including hoisting, fixing in position and applying wood
preservative on unexposed surface etc. complete with :
14.30.1 Sal wood
Code Description Unit Quantity Rate Amount
Details of cost for 300cudm.
MATERIAL
Sal wood
10x0.1mx0.1mx3.0m = 0.30 cum. Or
= 300 cudm
Add wastage @ 2% = 6.00 cudm.
Total = 306 cudm.
1199 Sal wood in scantling 10 cudm 30.60 600.00 18360.00
2204 Carriage of Timber cum 0.306 187.35 57.33
LABOUR
0112 Carpenter 2nd class day 0.70 714.00 499.80
0114 Beldar day 1.45 645.00 935.25
0100 Bandhani day 0.70 714.00 499.80
Priming coat (Wood preservative)
13.57.1 Rate as per item no 13.57.1
SH : Finishing sqm 0.80 47.10 37.68 A
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 20446.91 W
Add 1 % Water charges on "W-A" 204.09
TOTAL 20651.00 X
Add GST on "X-A" (multiplying
factor 0.1405) 2896.17
TOTAL 23547.17 Y
Add 15% CPOH on "Y-A" 3526.42
TOTAL 27073.60 Z
Add Cess @ 1% on "Z-A" 270.36
Cost of 300 cudm. 27343.96
Cost of 1 cum. 91146.53
Say 91146.55
SUB HEAD : 14- REPAIRS TO BUILDING 1126
14.30.2 Hollock wood
Code Description Unit Quantity Rate Amount
Details of cost for 300cudm.
MATERIAL
Hollock wood in scantling
10x0.1mx0.1mx3.0m = 0.30 cum. Or
= 300 cudm
Add wastage @ 2% = 6.00 cudm.
Total = 306 cudm.
2466 Hollock wood in scantling 10 cudm 30.60 357.00 10924.20
2204 Carriage of Timber cum 0.306 187.35 57.33
LABOUR
0112 Carpenter 2nd class day 0.70 714.00 499.80
0114 Beldar day 1.45 645.00 935.25
0100 Bandhani day 0.70 714.00 499.80
Priming coat (Wood preservative)
13.57.1 Rate as per item no 13.57.1
SH : Finishing sqm 0.80 47.10 37.68 A
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 13011.11 W
Add 1 % Water charges on "W-A" 129.73
TOTAL 13140.84 X
Add GST on "X-A" (multiplying
factor 0.1405) 1840.99
TOTAL 14981.84 Y
Add 15% CPOH on "Y-A" 2241.62
TOTAL 17223.46 Z
Add Cess @ 1% on "Z-A" 171.86
Cost of 300 cudm. 17395.32
Cost of 1 cum. 57984.40
Say 57984.40
14.31 Providing and fixing bright finished brass single acting spring hinges with
necessary brass screws etc. complete :
14.31.1 150 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0389 Brass single acting spring hinges 150 mm each 10.00 425.00 4250.00
0449 Brass screws 50 mm 100 Nos 0.80 220.00 176.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 4876.32 W
Add 1 % Water charges on "W" 48.76
TOTAL 4925.08 X
Add GST on "X" (multiplying
factor 0.1405) 691.97
TOTAL 5617.05 Y
Add 15% CPOH on "Y" 842.56
TOTAL 6459.61 Z
Add Cess @ 1% on "Z" 64.60
Cost of 10 hinges 6524.21
Cost of each 652.42
Say 652.40
SUB HEAD : 14- REPAIRS TO BUILDING 1127
14.31.2 125 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0390 Brass single acting spring hinges 125 mm each 10.00 285.00 2850.00
0449 Brass screws 50 mm 100 Nos 0.80 220.00 176.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 3476.32 W
Add 1 % Water charges on "W" 34.76
TOTAL 3511.08 X
Add GST on "X" (multiplying
factor 0.1405) 493.31
TOTAL 4004.39 Y
Add 15% CPOH on "Y" 600.66
TOTAL 4605.04 Z
Add Cess @ 1% on "Z" 46.05
Cost of 10 hinges 4651.10
Cost of each 465.11
Say 465.10
14.31.3 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0391 Brass single acting spring hinges 100 mm each 10.00 250.00 2500.00
0450 Brass screws 40 mm 100 Nos 0.80 170.00 136.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 3086.32 W
Add 1 % Water charges on "W" 30.86
TOTAL 3117.18 X
Add GST on "X" (multiplying
factor 0.1405) 437.96
TOTAL 3555.14 Y
Add 15% CPOH on "Y" 533.27
TOTAL 4088.42 Z
Add Cess @ 1% on "Z" 40.88
Cost of 10 hinges 4129.30
Cost of each 412.93
Say 412.95
SUB HEAD : 14- REPAIRS TO BUILDING 1128
14.32 Providing and fixing bright finished brass double acting spring hinges with
necessary brass screws etc. complete :
14.32.1 150 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0392 Brass double acting spring hinges
150 mm each 10.00 480.00 4800.00
0449 Brass screws 50 mm 100 Nos 0.80 220.00 176.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 5426.32 W
Add 1 % Water charges on “W” 54.26
TOTAL 5480.58 X
Add GST on “X” (multiplying
factor 0.1405) 770.02
TOTAL 6250.60 Y
Add 15% CPOH on “Y” 937.59
TOTAL 7188.19 Z
Add Cess @ 1% on “Z” 71.88
Cost of 10 hinges 7260.07
Cost of each 726.01
Say 726.00
14.32.2 125 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0393 Brass double acting spring hinges
125 mm each 10.00 400.00 4000.00
0449 Brass screws 50 mm 100 Nos 0.80 220.00 176.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 4626.32 W
Add 1 % Water charges on "W" 46.26
TOTAL 4672.58 X
Add GST on "X" (multiplying
factor 0.1405) 656.50
TOTAL 5329.08 Y
Add 15% CPOH on "Y" 799.36
TOTAL 6128.44 Z
Add Cess @ 1% on "Z" 61.28
Cost of 10 hinges 6189.72
Cost of each 618.97
Say 618.95
SUB HEAD : 14- REPAIRS TO BUILDING 1129
14.32.3 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0394 Brass double acting spring hinges
100 mm each 10.00 390.00 3900.00
0450 Brass screws 40 mm 100 Nos 0.80 170.00 136.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 4486.32 W
Add 1 % Water charges on "W" 44.86
TOTAL 4531.18 X
Add GST on "X" (multiplying
factor 0.1405) 636.63
TOTAL 5167.81 Y
Add 15% CPOH on "Y" 775.17
TOTAL 5942.98 Z
Add Cess @ 1% on "Z" 59.43
Cost of 10 hinges 6002.41
Cost of each 600.24
Say 600.25
14.33 Providing and fixing bright finished brass flush bolts with necessary brass
screws etc. complete :
14.33.1 250 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0404 Brass flush bolt 250 mm each 10.00 150.00 1500.00
0452 Brass screws 25 mm 100 Nos 0.60 100.00 60.00
9977 Carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class Day 0.20 784.00 156.80
TOTAL 1724.52 W
Add 1 % Water charges on "W" 17.25
TOTAL 1741.76 X
Add GST on "X" (multiplying
factor 0.1405) 244.72
TOTAL 1986.48 Y
Add 15% CPOH on "Y" 297.97
TOTAL 2284.45 Z
Add Cess @ 1% on "Z" 22.84
Cost of 10 hinges 2307.30
Cost of each 230.73
Say 230.75
SUB HEAD : 14- REPAIRS TO BUILDING 1130
14.33.2 150 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0405 Brass flush bolt 150 mm each 10.00 130.00 1300.00
0452 Brass screws 25 mm 100 Nos 0.60 100.00 60.00
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0111 Carpenter 1st class day 0.17 784.00 133.28
TOTAL 1499.07 W
Add 1 % Water charges on "W" 14.99
TOTAL 1514.06 X
Add GST on "X" (multiplying
factor 0.1405) 212.73
TOTAL 1726.78 Y
Add 15% CPOH on "Y" 259.02
TOTAL 1985.80 Z
Add Cess @ 1% on "Z" 19.86
Cost of 10 hinges 2005.66
Cost of each 200.57
Say 200.55
14.33.3 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0406 Brass flush bolt 100 mm each 10.00 90.00 900.00
0452 Brass screws 25 mm 100 Nos 0.60 100.00 60.00
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0111 Carpenter 1st class day 0.17 784.00 133.28
TOTAL 1099.07 W
Add 1 % Water charges on "W" 10.99
TOTAL 1110.06 X
Add GST on "X" (multiplying
factor 0.1405) 155.96
TOTAL 1266.02 Y
Add 15% CPOH on "Y" 189.90
TOTAL 1455.92 Z
Add Cess @ 1% on "Z" 14.56
Cost of 10 hinges 1470.48
Cost of each 147.05
Say 147.05
14.34 Providing and fixing 150 mm bright finished floor brass door stopper with rubber
cushion, necessary brass screws etc. to suit shutter thickness complete
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0417 Brass 150 mm floor door stopper
(0.357kg) each 10.00 160.00 1600.00
SUB HEAD : 14- REPAIRS TO BUILDING 1131
Code Description Unit Quantity Rate Amount
0450 Brass screws 40 mm 100 Nos 0.40 170.00 68.00
9977 Carriage of material L.S. 2.73 2.12 5.79
LABOUR
0111 Carpenter 1st class day 0.07 784.00 54.88
9999 Sundries (wooden plugs including fixing
in the floor) L.S. 6.37 2.12 13.50
TOTAL 1742.17 W
Add 1 % Water charges on "W" 17.42
TOTAL 1759.59 X
Add GST on "X" (multiplying
factor 0.1405) 247.22
TOTAL 2006.82 Y
Add 15% CPOH on "Y" 301.02
TOTAL 2307.84 Z
Add Cess @ 1% on "Z" 23.08
Cost of 10 Nos 2330.92
Cost of each 233.09
Say 233.10
14.35 Providing and fixing bright finished brass hard drawn hooks and eyes :
14.35.1 300 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0418 Brass hard drawn hooks and eyes
300 mm 10 Nos 1.00 600.00 600.00
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
TOTAL 648.97 W
Add 1 % Water charges on “W” 6.49
TOTAL 655.46 X
Add GST on “X” (multiplying
factor 0.1405) 92.09
TOTAL 747.55 Y
Add 15% CPOH on “Y” 112.13
TOTAL 859.68 Z
Add Cess @ 1% on “Z” 8.60
Cost of 10 Nos 868.28
Cost of each 86.83
Say 86.85
14.35.2 250 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0419 Brass hard drawn hooks and eyes
250 mm 10 Nos 1.00 574.00 574.00
9977 Carriage of material L.S. 0.91 2.12 1.93
SUB HEAD : 14- REPAIRS TO BUILDING 1132
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
TOTAL 622.97 W
Add 1 % Water charges on “W” 6.23
TOTAL 629.20 X
Add GST on “X” (multiplying
factor 0.1405) 88.40
TOTAL 717.60 Y
Add 15% CPOH on “Y” 107.64
TOTAL 825.24 Z
Add Cess @ 1% on “Z” 8.25
Cost of 10 hooks and eyes 833.49
Cost of 1 hook and eye 83.35
Say 83.35
14.35.3 200 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0420 Brass hard drawn hooks and eyes
200 mm 10 Nos 1.00 510.00 510.00
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
TOTAL 558.97 W
Add 1 % Water charges on "W" 5.59
TOTAL 564.56 X
Add GST on "X" (multiplying
factor 0.1405) 79.32
TOTAL 643.88 Y
Add 15% CPOH on "Y" 96.58
TOTAL 740.46 Z
Add Cess @ 1% on "Z" 7.40
Cost of 10 Nos 747.87
Cost of each 74.79
Say 74.80
14.35.4 150 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0421 Brass hard drawn hooks and eyes
150 mm 10 Nos 1.00 400.00 400.00
9977 Carriage of material L.S. 0.91 2.12 1.93
SUB HEAD : 14- REPAIRS TO BUILDING 1133
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
TOTAL 448.97 W
Add 1 % Water charges on "W" 4.49
TOTAL 453.46 X
Add GST on "X" (multiplying
factor 0.1405) 63.71
TOTAL 517.17 Y
Add 15% CPOH on "Y" 77.58
TOTAL 594.75 Z
Add Cess @ 1% on "Z" 5.95
Cost of 10 Nos 600.69
Cost of each 60.07
Say 60.05
14.35.5 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0422 Brass hard drawn hooks and eyes
100 mm 10 Nos 1.00 345.00 345.00
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
TOTAL 393.97 W
Add 1 % Water charges on "W" 3.94
TOTAL 397.91 X
Add GST on "X" (multiplying
factor 0.1405) 55.91
TOTAL 453.82 Y
Add 15% CPOH on "Y" 68.07
TOTAL 521.89 Z
Add Cess @ 1% on "Z" 5.22
Cost of 10 Nos 527.11
Cost of each 52.71
Say 52.70
14.36 Providing and fixing bright finished brass fan light pivot with necessary brass
screws etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0429 Brass fanlight pivot 10 Nos 1.00 168.00 168.00
0450 Brass screws 40 mm 100 Nos 0.40 170.00 68.00
9977 Carriage of material L.S. 0.91 2.12 1.93
SUB HEAD : 14- REPAIRS TO BUILDING 1134
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.08 784.00 62.72
TOTAL 300.65 W
Add 1 % Water charges on “W” 3.01
TOTAL 303.66 X
Add GST on “X” (multiplying
factor 0.1405) 42.66
TOTAL 346.32 Y
Add 15% CPOH on “Y” 51.95
TOTAL 398.27 Z
Add Cess @ 1% on “Z” 3.98
Cost of 10 Nos 402.25
Cost of each 40.22
Say 40.20
14.37 Providing and fixing 300 mm long bright finished brass chain with hook for fan
light including necessary brass screws etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0430 Brass chain with hook for fan light catch each 10.00 36.00 360.00
0452 Brass screws 25 mm 100 Nos 0.40 100.00 40.00
9977 Carriage of material L.S. 0.91 2.12 1.93
LABOUR
0111 Carpenter 1st class day 0.10 784.00 78.40
TOTAL 480.33 W
Add 1 % Water charges on "W" 4.80
TOTAL 485.13 X
Add GST on "X" (multiplying
factor 0.1405) 68.16
TOTAL 553.29 Y
Add 15% CPOH on "Y" 82.99
TOTAL 636.29 Z
Add Cess @ 1% on "Z" 6.36
Cost of 10 Nos 642.65
Cost of each 64.27
Say 64.25
14.38 Providing and fixing bright finished brass quadrant stay 300 mm long with
necessary brass screws etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0427 Brass quadrant stays 300 mm each 10.00 110.00 1100.00
0452 Brass screws 25 mm 100 Nos 0.40 100.00 40.00
9977 Carriage of material L.S. 0.91 2.12 1.93
SUB HEAD : 14- REPAIRS TO BUILDING 1135
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.10 784.00 78.40
TOTAL 1220.33 W
Add 1 % Water charges on "W" 12.20
TOTAL 1232.53 X
Add GST on "X" (multiplying
factor 0.1405) 173.17
TOTAL 1405.70 Y
Add 15% CPOH on "Y" 210.86
TOTAL 1616.56 Z
Add Cess @ 1% on "Z" 16.17
Cost of 10 quadrant stayes 1632.72
Cost of each 163.27
Say 163.25
14.39 Providing and fixing bright finished brass helical door spring (superior quality).
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0442 Brass helical spring 150 mm each 10.00 290.00 2900.00
0449 Brass screws 50 mm 100 Nos 0.40 220.00 88.00
0452 Brass screws 25 mm 100 Nos 0.20 100.00 20.00
9977 Carriage of material L.S. 3.84 2.12 8.14
LABOUR
0111 Carpenter 1st class day 0.40 784.00 313.60
0114 Beldar day 0.20 645.00 129.00
TOTAL 3458.74 W
Add 1 % Water charges on “W” 34.59
TOTAL 3493.33 X
Add GST on “X” (multiplying
factor 0.1405) 490.81
TOTAL 3984.14 Y
Add 15% CPOH on “Y” 597.62
TOTAL 4581.76 Z
Add Cess @ 1% on “Z” 45.82
Cost of 10 Nos 4627.58
Cost of each 462.76
Say 462.75
14.40 Providing and fixing chromium plated brass butt hinges with necessary
chromium plated brass screws etc. complete.
14.40.1 125x70x4 mm (ordinary type)
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0525 Chromium plated Brass butt hinges
(light/ordinary) type 125x70x4 mm 10 Nos 1.00 805.00 805.00
0585 Chromium plated Brass screws 50 mm 100 Nos 1.00 300.00 300.00
9977 Carriage of material L.S. 3.64 2.12 7.72
SUB HEAD : 14- REPAIRS TO BUILDING 1136
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.14 784.00 109.76
0114 Beldar day 0.10 645.00 64.50
TOTAL 1286.98 W
Add 1 % Water charges on "W" 12.87
TOTAL 1299.85 X
Add GST on "X" (multiplying
factor 0.1405) 182.63
TOTAL 1482.48 Y
Add 15% CPOH on "Y" 222.37
TOTAL 1704.85 Z
Add Cess @ 1% on "Z" 17.05
Cost of 10 nos. 1721.89
Cost of each 172.19
Say 172.20
14.40.2 100x70x4 mm (ordinary type)
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0526 Chromium plated Brass butt hinges
(light/ordinary) type 100x70x4 mm 10 Nos 1.00 690.00 690.00
0586 Chromium plated Brass screws 40 mm 100 Nos 0.80 290.00 232.00
9977 Carriage of material L.S. 3.64 2.12 7.72
LABOUR
0111 Carpenter 1st class day 0.14 784.00 109.76
0114 Beldar day 0.10 645.00 64.50
TOTAL 1103.98 W
Add 1 % Water charges on “W” 11.04
TOTAL 1115.02 X
Add GST on “X” (multiplying
factor 0.1405) 156.66
TOTAL 1271.68 Y
Add 15% CPOH on “Y” 190.75
TOTAL 1462.43 Z
Add Cess @ 1% on “Z” 14.62
Cost of 10 nos. 1477.05
Cost of each 147.71
Say 147.70
14.40.3 75x65x4 mm (heavy type)
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0524 Chromium plated Brass butt hinges
(heavy) type 75x65x4 .0 mm (200gms) 10 Nos 1.00 905.00 905.00
0587 Chromium plated Brass screws 30 mm 100 Nos 0.60 240.00 144.00
9977 Carriage of material L.S. 1.82 2.12 3.86
SUB HEAD : 14- REPAIRS TO BUILDING 1137
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.14 784.00 109.76
0114 Beldar day 0.10 645.00 64.50
TOTAL 1227.12 W
Add 1 % Water charges on "W" 12.27
TOTAL 1239.39 X
Add GST on "X" (multiplying
factor 0.1405) 174.13
TOTAL 1413.52 Y
Add 15% CPOH on "Y" 212.03
TOTAL 1625.55 Z
Add Cess @ 1% on "Z" 16.26
Cost of 10 nos. 1641.81
Cost of each 164.18
Say 164.20
14.40.4 75x40x2.5 mm (ordinary type)
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0527 Chromium plated Brass butt hinges
(light/ordinary) type 75x40x2.5 mm 10 Nos 1.00 421.00 421.00
0587 Chromium plated Brass screws 30 mm 100 Nos 0.60 240.00 144.00
9977 Carriage of material L.S. 1.82 2.12 3.86
LABOUR
0111 Carpenter 1st class day 0.14 784.00 109.76
0114 Beldar day 0.10 645.00 64.50
TOTAL 743.12 W
Add 1 % Water charges on "W" 7.43
TOTAL 750.55 X
Add GST on "X" (multiplying
factor 0.1405) 105.45
TOTAL 856.00 Y
Add 15% CPOH on "Y" 128.40
TOTAL 984.40 Z
Add Cess @ 1% on "Z" 9.84
Cost of 10 nos. 994.25
Cost of each 99.42
Say 99.40
14.40.5 50x40x2.5 mm (ordinary type)
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
0528 Chromium plated Brass butt hinges
(light/ordinary) type 50x40x2.5 mm 10 Nos 1.00 180.00 180.00
0589 Chromium plated Brass screws 20 mm 100 Nos 0.40 160.00 64.00
9977 Carriage of material L.S. 0.91 2.12 1.93
SUB HEAD : 14- REPAIRS TO BUILDING 1138
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.08 784.00 62.72
TOTAL 308.65 W
Add 1 % Water charges on "W" 3.09
TOTAL 311.74 X
Add GST on "X" (multiplying
factor 0.1405) 43.80
TOTAL 355.53 Y
Add 15% CPOH on "Y" 53.33
TOTAL 408.86 Z
Add Cess @ 1% on "Z" 4.09
Cost of 10 nos. 412.95
Cost of each 41.30
Say 41.30
14.41 Providing and fixing 85x42 mm chromium plated brass pull bolt lock with
necessary chromium plated brass screws, nuts, bolts and washers etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Nos
MATERIAL
2467 Chromium plated Brass pull bolt lock
(locking bolt) of size 85 mmx42 mm
with screws,bolts,nuts and washers
complete each 10.00 172.00 1720.00
9988 Carriage of materials & sundries L.S. 6.37 2.12 13.50
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
TOTAL 1912.00 W
Add 1 % Water charges on "W" 19.12
TOTAL 1931.12 X
Add GST on "X" (multiplying
factor 0.1405) 271.32
TOTAL 2202.45 Y
Add 15% CPOH on "Y" 330.37
TOTAL 2532.81 Z
Add Cess @ 1% on "Z" 25.33
Cost of 10 nos. 2558.14
Cost of each 255.81
Say 255.80
14.72 Providing and fixing double scaffolding system (cup lock type) on the exterior
side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to
centre, horizontal & vertical tubes joining with cup & lock system with M.S.
tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the
scaffolding for working platform etc. and maintaining it in a serviceable condition
for the required duration as approved and removing it there after .The scaffolding
system shall be stiffened with bracings, runners, connection with the building
etc wherever required for inspection of work at required locations with essential
safety features for the workmen etc. complete as per directions and approval of
SUB HEAD : 14- REPAIRS TO BUILDING 1139
Engineer-in-charge .The elevational area of the scaffolding shall be measured
for payment purpose .The payment will be made once irrespective of duration
of scaffolding.
Note: - This item to be used for maintenance work judicially, necessary deduction
for scaffolding in the existing item to be done.
Code Description Unit Quantity Rate Amount
Details of cost for area 22.5m x 9.0m
=202.5 sqm
14.72X Rate as per Item No.14.72X of
SH:Repairs to Buildings each 1.00 7911.85 7911.85
2205 Carriage of Steel tonne 6.054 145.72 882.19
40mm dia MS pipe = 3765.42 kg
25mm spigot = 123.98 kg
Nuts & bolts = 37.80 kg
Clamp = 120 nos @ 1.00kg each
= 120.00 kg
Challies = 90 nos @ 15.00kg each
= 1350.00 kg
Cup locks = 1314 nos @ 0.50kg each
= 657.00 kg
Total = 6054.20 kg = 6.054 tonne
LABOUR
0116 Fitter (grade 1) day 15.50 784.00 12152.00
0114 Beldar day 31.00 645.00 19995.00
9999 Sundries L.S. 1035 2.12 2194.20
TOTAL 43135.24 W
Add 1 % Water charges on "W" 431.35
TOTAL 43566.59 X
Add GST on "X" (multiplying
factor 0.1405) 6121.11
TOTAL 49687.70 Y
Add 15% CPOH on "Y" 7453.15
TOTAL 57140.85 Z
Add Cess @ 1% on "Z" 571.41
Cost of 202.50 sqm. 57712.26
Cost of 1 sqm. 285.00
Say 285.00
14.72X Scaffolding
Code Description Unit Quantity Rate Amount
Details of cost for area 22.5 x 9.0
= 202.50 sqm
MATERIAL
Assuming shuttering material will
become unserviceable after use of
40 times
7397 Base jack each 14.00 145.00 2030.00
7x2=14 nos
4009 Mild steel tubes hot finished welded type kilogram 3765.42 60.00 225925.20
40mm dia M.S. Tube
Vertical standard 2.5m length
= 7x2x9x2.5 = 315.00 m
SUB HEAD : 14- REPAIRS TO BUILDING 1140
Code Description Unit Quantity Rate Amount
Bracing ledder 1.5m length = 7x2x9x
4.0873 = 513.00 m
Side support 6.00m length = 3x2x6.00
= 36.00 m
Horizontal support 3.00m length
= 18x3x3.00 = 162.00 m
Total = 1026.00m @ 3.67 kg/m
= 3765.42 kg
7387 Spigot for standard jointing kg 123.98 40.00 4959.20
7x2x9 = 126 nos x 0.40m length
= 50.40m
50.40m @ 2.46kg/m = 123.98kg
1034 Bolts and nuts upto 300 mm in length quintal 0.378 5200.00 1965.60
2x7x2x9 = 252 nos @ 0.15 kg each
= 37.80 kg = 0.378 q
7346 Double coupler each 120.00 46.00 5520.00
2x3x2 + 2x18x3 = 120 nos
7398 Challies each 90.00 765.00 68850.00
3 nos x 18 lines = 54 nos
Two level plate challies = 2x 18 lines
= 36 nos, Total = 90 nos
7399 Cup lock each 1314.00 48.00 63072.00
Vertical standards 5x7x2x9
= 630.00 Nos.
2x18x19 = 684 Nos.
Total =1314 Nos.
TOTAL 372322.00 P
Add 10% for maintenance on P 37232.20 Q
Less 25% salvage value on P -93080.5 R
TOTAL (P+Q+R) 316473.70
Considering that scaffolding shall
be unserviceable after using
40 times
cost of using once 7911.84
Say 7911.85
14.73 Providing and fixing bright finished brass casement window fasteners or peg
stays to windows/ ventilators with necessary welding and machine screws etc.
complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos
(10 x 0.20 = 2.00 kg)
MATERIAL
0423 Brass casement window fastener each 10.00 45.00 450.00
9999 Fixing charges including welding
and materials etc. L.S. 125.58 2.12 266.23
SUB HEAD : 14- REPAIRS TO BUILDING 1141
Code Description Unit Quantity Rate Amount
9977 Carriage of materials L.S. 3.64 2.12 7.72
TOTAL 723.95 W
Add 1 % Water charges on "W" 7.24
TOTAL 731.19 X
Add GST on "X" (multiplying
factor 0.1405) 102.73
TOTAL 833.92 Y
Add 15% CPOH on "Y" 125.09
TOTAL 959.01 Z
Add Cess @ 1% on "Z" 9.59
Cost of 2.00kg window fasteners 968.60
Cost of 1 kg window fastener 484.30
Say 484.30
14.74 Providing and fixing 14 mm bright finished brass spring catch to steel centre
hung ventilators with necessary welding and machine screws etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos
MATERIAL
0428 Brass fanlight catch 10 Nos 1.00 170.00 170.00
9999 Fixing charges including welding
and materials etc. L.S. 125.58 2.12 266.23
9977 Carriage of materials L.S. 3.64 2.12 7.72
TOTAL 443.95 W
Add 1 % Water charges on "W" 4.44
TOTAL 448.39 X
Add GST on "X" (multiplying
factor 0.1405) 63.00
TOTAL 511.38 Y
Add 15% CPOH on "Y" 76.71
TOTAL 588.09 Z
Add Cess @ 1% on "Z" 5.88
Cost of 10 window fasteners 593.97
Cost of each 59.40
Say 59.40
14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and
under, including cutting the patch in proper shape, raking out joints and
preparing plastering the wall surface with white cement based polymer modified
self curing mortar, including disposal of rubbish, all complete as per the direction
of Engineer-In-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL
0772 White cement based polymer modified
self curing compound in powder form kg 125.00 15.00 1875.00
i/c 2% wastage
SUB HEAD : 14- REPAIRS TO BUILDING 1142
Code Description Unit Quantity Rate Amount
9977 Carriage of white cement based
polymer modified self curing compound
in powder form L.S. 21.10 2.12 44.73
LABOUR
0155 Mason (average) day 1.21 749.00 906.29
0114 Beldar day 0.54 645.00 348.30
0115 Coolie day 1.29 645.00 832.05
9999 Scaffolding and sunderies L.S. 15.21 2.12 32.25
TOTAL 4038.62 W
Add 1 % Water charges on "W" 40.39
TOTAL 4079.00 X
Add GST on "X" (multiplying
factor 0.1405) 573.10
TOTAL 4652.10 Y
Add 15% CPOH on "Y" 697.82
TOTAL 5349.92 Z
Add Cess @ 1% on "Z" 53.50
Cost of 10 sqm 5403.42
Cost of 1 sqm 540.34
Say 540.35
14.75A Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre
capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish
from the tank and cleaning the tank with fresh water disinfecting with bleaching
powder @ 0.5gm per litre capacity of tank including marking the date of cleaning
on the side of tank body with the help of stencil and paint and disposing of
malba all complete as per direction of Engineer-in-Charge. (The old date already
written on tank should be removed with paint remover or black paint and if date
is not written with the stencil or old date is not removed deduction will be made
@ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged
that is to be repaired by contractor at his own cost and nothing extra will be
paid on this account)
Code Description Unit Quantity Rate Amount
Details of cost for 10 tanks
1 tank is of 500 litres capacity i.e.
5000 litres
MATERIAL
1301 Bleaching powder quintal 0.025 1800.00 45.00
2264 Carriage of Rubbish cum 0.25 163.93 40.98
(asuming 0.040m depth of silt)
9999 Marking with paint i/c removal of
existing markings L.S. 30.00 2.12 63.60
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 1.00 714.00 714.00
for opening ball cock wheel valve and
other fittings
SUB HEAD : 14- REPAIRS TO BUILDING 1143
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.00 645.00 645.00
for cleaning disinfecting etc
TOTAL 1508.58 W
Add 1 % Water charges on “W” 15.09
TOTAL 1523.67 X
Add GST on “X” (multiplying
factor 0.1405) 214.08
TOTAL 1737.74 Y
Add 15% CPOH on “Y” 260.66
TOTAL 1998.41 Z
Add Cess @ 1% on “Z” 19.98
Cost of 5000 litres 2018.39
Cost of 1 litre 0.40
Say 0.40
14.76 Cleaning and desilting of gully trap chamber, including removal of rubbish mixed
with earth etc. and disposal of same, all as per the direction of Engineer-in-
charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Nos.
LABOUR
0129 Sewerman day 1.00 645.00 645.00
9999 T & P Bamboo, bucket, whell barrow etc. L.S. 11.20 2.12 23.74
TOTAL 668.74 W
Add 1 % Water charges on "W" 6.69
TOTAL 675.43 X
Add GST on "X" (multiplying
factor 0.1405) 94.90
TOTAL 770.33 Y
Add 15% CPOH on "Y" 115.55
TOTAL 885.88 Z
Add Cess @ 1% on "Z" 8.86
Cost of 10 nos 894.74
Cost of each 89.47
Say 89.45
14.77 Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic
operated high pressure suction cum jetting sewer cleaning machine fitted with
pump having 4000 litres suction capacity and 6000 litres water jetting tank
capacity including skilled operator, supervising engineer etc. for cleaning and
partial desilting of manholes and dechocking of sewer lines. Dechocking and
flushing of sewer line from one manhole to another by high pressure jetting
system of 2200 PSI for sewer line from 150mm dia upto 300mm
Code Description Unit Quantity Rate Amount
Details of Cost for 208 metres
MATERIAL
9999 Soap, brush, cloths & sundries L.S. 345.00 2.12 731.40
8500 Water for jetting / blowback 1000 litre 0.002 1500.00 3.00
SUB HEAD : 14- REPAIRS TO BUILDING 1144
Code Description Unit Quantity Rate Amount
Machineries
0087 Hire Charges of Suction Jeting machine
2200 PSI machine i/c POL and operator day 1.00 40000.00 40000.00
LABOUR
0139 Skilled Beldar (for floor rubbing etc.) day 4.00 714.00 2856.00
0160 Technician day 1.00 853.00 853.00
TOTAL 44443.40 W
Add 1 % Water charges on "W" 444.43
TOTAL 44887.83 X
Add GST on "X" (multiplying
factor 0.1405) 6306.74
TOTAL 51194.57 Y
Add 15% CPOH on "Y" 7679.19
TOTAL 58873.76 Z
Add Cess @ 1% on "Z" 588.74
Cost of 208 metres 59462.50
Cost of 1.00 metre 285.88
Say 285.90
14.78 Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging)
including disposal of slit and rubbish, all as per direction of Engineer-in-Charge.
The cleaning shall consist following operations:-
(i) Tank shall be emptied of water by pumping & bottom shall be cleaned of
silt and other deposits.
(ii) Entire surface area of the sump shall then scrubbed thoroughly with wire
brush etc. and pressure washed with water.
(iii) Chlorination of RCC internal surface by liquid chlorine.
(iv) The treated surface shall be dried using air jetting and all loose particles
shall be removal from the surface.
(v) Finally the surface shall be treated with ultraviolet radiation etc. as per
direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Let a underground tank of capacity 272000
litre or 272 KL and area of tank is 570sqm
(a) Dewater and slit cleaning
Considering through pumping 20% of
water to be lifted, water discharge
=(272 x 20/100=54.40KL)
Cost of pumping water with pump of
capacity 4000 litres per hours , = (54.4/
4 =13.6 hours = @ 8 hours/ day = 1.7
day)
0011 Hire charges of Pump set of capacity
4000 litres/hour day 1.70 700.00 1190.00
0114 Beldar day 10.88 645.00 7017.60
(b) Scrabing the internal surface of tank
0114 Beldar day 5.13 645.00 3308.85
0115 Coolie day 2.28 645.00 1470.60
0101 Bhisti day 2.28 714.00 1627.92
9999 Sundries L.S. 142.50 2.12 302.10
(c) Bleaching
SUB HEAD : 14- REPAIRS TO BUILDING 1145
Code Description Unit Quantity Rate Amount
1301 Bleaching powder quintal 0.57 1800.00 1026.00
0006 Hire charges of Spraying machine
including electric charges day 14.25 250.00 3562.50
0138 Sprayer (for bitumen, tar etc.) day 14.25 714.00 10174.50
(d) Air jetting
0058 Air compressor hour 2.00 200.00 400.00
0114 Beldar day 0.25 645.00 161.25
(e) Ultra Violet Radiation
0085 Using cost of Ultra Violet Radiation tube hour 0.50 190.00 95.00
0114 Beldar day 0.0625 645.00 40.31
TOTAL 30376.63 W
Add 1 % Water charges on "W" 303.77
TOTAL 30680.40 X
Add GST on "X" (multiplying
factor 0.1405) 4310.60
TOTAL 34990.99 Y
Add 15% CPOH on "Y" 5248.65
TOTAL 40239.64 Z
Add Cess @ 1% on "Z" 402.40
Cost of 570 sqm 40642.04
Cost of 1 sqm 71.30
Say 71.30
14.79 Disconnecting damaged overhead/terrace PVC water storage tank of any size
from water supply line and removing from the terrace including shifting at
ground level as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
LABOUR
For disconnecting & dismantling of
existing W/s line of water storage
tanks on terrace of Qtrs.
0117 Assistant Fitter or 2nd class Fitter day 0.10 714.00 71.40
0114 Beldar day 0.10 645.00 64.50
For Bringing the tank at Ground Level
0114 Beldar day 0.20 645.00 129.00
9999 Sundries L.S. 1.10 2.12 2.33
TOTAL 267.23 W
Add 1 % Water charges on “W” 2.67
TOTAL 269.90 X
Add GST on “X” (multiplying
factor 0.1405) 37.92
TOTAL 307.83 Y
Add 15% CPOH on “Y” 46.17
TOTAL 354.00 Z
Add Cess @ 1% on “Z” 3.54
Cost for each 357.54
Say 357.55
SUB HEAD : 14- REPAIRS TO BUILDING 1146
14.80 Providing & fixing White vitreous china water closet squatting pan (Indian type)
along with "S" or "P" trap including dismantling of old WC seat and "S" or "P"
trap at site complete with all operations including all necessary materials, labour
and disposal of dismantled material i/c malba, all complete as per the direction
of Engineer-in charge.
14.80.1 Long pattern W.C Pan of size 580x440 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
1953 Vitreous china Indian type W.C.
pan size 580 mm each 1.00 475.00 475.00
1970 Vitreous china foot rests 250x125x25 mm pair 1.00 103.00 103.00
1890 Centrifugally sand cast (spun) S&S
“P” or “S” trap each 1.00 325.00 325.00
9999 Cement sand & grit etc. L.S. 13.36 2.12 28.32
9977 Carriage of materials L.S. 13.52 2.12 28.66
Less for
1880 Dismantled “P” or “S” trap scrap
(app. Wt 2 kg.) kg -2.00 25.00 -50.00
LABOUR
(a) For dismantling WC seat and P
or S trap
0129 Sewerman day 0.05 645.00 32.25
0114 Beldar day 0.20 645.00 129.00
(b) For Fixing WC seat and “P” or “S” trap
0126 Mason 1st class day 0.80 784.00 627.20
0114 Beldar day 0.80 645.00 516.00
TOTAL 2214.44 W
Add 1 % Water charges on “W” 22.14
TOTAL 2236.58 X
Add GST on “X” (multiplying
factor 0.1405) 314.24
TOTAL 2550.82 Y
Add 15% CPOH on “Y” 382.62
TOTAL 2933.44 Z
Add Cess @ 1% on “Z” 29.33
Cost of each 2962.78
Say 2962.80
14.80.2 Orissa pattern W.C Pan of size 580x440 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
1954 Vitreous china orrisa type W.C. pan
size 580 mm each 1.00 1290.00 1290.00
1890 Centrifugally sand cast (spun) S&S
"P" or "S" trap each 1.00 325.00 325.00
9999 Cement sand & grit etc. L.S. 13.36 2.12 28.32
9977 Carriage of materials L.S. 13.52 2.12 28.66
Less for
1880 Dismantled "P" or "S" trap scrap
(app. Wt 2 kg.) kg -2.00 25.00 -50.00
SUB HEAD : 14- REPAIRS TO BUILDING 1147
Code Description Unit Quantity Rate Amount
LABOUR
(a) For dismantling WC seat and
P or S trap
0129 Sewerman day 0.05 645.00 32.25
0114 Beldar day 0.125 645.00 80.63
(b) For Fixing WC seat and "P" or
"S" trap
0126 Mason 1st class day 0.80 784.00 627.20
0114 Beldar day 0.80 645.00 516.00
TOTAL 2878.06 W
Add 1 % Water charges on "W" 28.78
TOTAL 2906.84 X
Add GST on "X" (multiplying
factor 0.1405) 408.41
TOTAL 3315.25 Y
Add 15% CPOH on "Y" 497.29
TOTAL 3812.54 Z
Add Cess @ 1% on "Z" 38.13
Cost of each 3850.67
Say 3850.65
14.81 Cutting holes of required size in brick masonry wall for fixing of exhaust fan
including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and
making good the same etc. complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of Cost for 10 holes
Size 0.30x0.30x0.23 m wall
MATERIAL
12 mm plaster 1:4 (1 Cement:
4 Coarse sand)
Actual Area (10x4x0.3x0.23)
= 0.296 + 0.24
L.S. For corners/sides = 3.00 Sqm
13.4.1 Rate as per Item No.13.4.1 of
SH:FINISHING sqm 3.00 307.25 921.75 A
7752 PVC slotted pipe 200 mm dia as per
IS: 12818 metre 0.25 810.00 202.50
9999 Sundries L.S. 8.06 2.12 17.09
LABOUR
Proportionate labour taken as actually
required at site
0123 Mason (brick layer) 1st class day 0.11 784.00 86.24
(0.16/0.0306)= 0.11 Nos.
0124 Mason (brick layer) 2nd class day 0.11 714.00 78.54
(0.16/0.030)x0.207 = 0.11 Nos.
0114 Beldar day 1.10 645.00 709.50
(1.25x0.207)/0.0306 =1.10 Nos.
SUB HEAD : 14- REPAIRS TO BUILDING 1148
Code Description Unit Quantity Rate Amount
9999 Add L.S. For Delay L.S. 16.12 2.12 34.17
TOTAL 2049.79 W
Add 1 % Water charges on “W-A” 11.28
TOTAL 2061.07 X
Add GST on “X-A” (multiplying
factor 0.1405) 160.07
TOTAL 2221.15 Y
Add 15% CPOH on “Y-A” 194.91
TOTAL 2416.06 Z
Add Cess @ 1% on “Z-A” 14.94
Cost of 10 nos 2431.00
Cost of each 243.10
Say 243.10
14.82 Dismantling W.C. Pan of all sizes including disposal of dismantled materials
i/c malba all complete as per directions of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
LABOUR
0114 Beldar day 0.125 645.00 80.63
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 82.75 W
Add 1 % Water charges on “W” 0.83
TOTAL 83.57 X
Add GST on “X” (multiplying
factor 0.1405) 11.74
TOTAL 95.31 Y
Add 15% CPOH on “Y” 14.30
TOTAL 109.61 Z
Add Cess @ 1% on “Z” 1.10
Cost of each 110.71
Say 110.70
14.83 Hacking of CC flooring including cleaning for surface etc. complete as per
direction of the Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
LABOUR
0114 Beldar day 0.03 645.00 19.35
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 21.47 W
Add 1 % Water charges on “W” 0.21
TOTAL 21.68 X
Add GST on “X” (multiplying
factor 0.1405) 3.05
TOTAL 24.73 Y
Add 15% CPOH on “Y” 3.71
TOTAL 28.44 Z
Add Cess @ 1% on “Z” 0.28
Cost of 10 sqm 28.73
Cost of 1 sqm 2.87
Say 2.85
SUB HEAD : 14- REPAIRS TO BUILDING 1149
14.84 Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes
(within 50 metres lead) as per direction of Engineer-in-Charge.
(a) Internal Work- Exposed on wall
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
9999 Dismantling of G.I. Pipe and stacking etc. L.S. 10.00 2.12 21.20
TOTAL 21.20 W
Add 1 % Water charges on "W" 0.21
TOTAL 21.41 X
Add GST on "X" (multiplying
factor 0.1405) 3.01
TOTAL 24.42 Y
Add 15% CPOH on "Y" 3.66
TOTAL 28.08 Z
Add Cess @ 1% on "Z" 0.28
Cost of 10 metres 28.36
Cost of 1 metre 2.84
Say 2.85
14.85 Taking out existing wooden door shutter, repair by cutting, painting etc. and
refixing of repaired door shutters to existing door frames, including replacement
of hinges with screws, etc. as required, all complete as per the direction of the
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for one shutter (2.2 sqm)
Normal exiting size of shutter
1.00x2.02m =2.02sqm
MATERIAL
0637 Bright finished or black enameled mild
steel screws 40 mm 100 Nos 0.24 60.00 14.40
Assuming old hinges fixed in Tee
iron frames
Half qty = 48/2=24 needs replacement
LABOUR
0156 Carpenter (average) day 0.18 749.00 134.82
0114 Beldar day 0.18 645.00 116.10
TOTAL 265.32 W
Add 1 % Water charges on "W" 2.65
TOTAL 267.97 X
Add GST on "X" (multiplying
factor 0.1405) 37.65
TOTAL 305.62 Y
Add 15% CPOH on "Y" 45.84
TOTAL 351.47 Z
Add Cess @ 1% on "Z" 3.51
Cost for 2.2 sqm or each shutter 354.98
Cost for 2.02 sqm or each shutter 325.94
Say 325.95
SUB HEAD : 14- REPAIRS TO BUILDING 1150
14.86 Providing and laying in situ seven course water proofing treatment with APP
(Atactic poly-propylene) modified Polymeric memberane over roof consisting
of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of
bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of
grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane
APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight
consisting of five layers prefabricated with centre core as 20 micron HMHDPE
film sandwiched on both sides with polymeric mix and the polymeric mix is
protected on both side with 20 micron HMHDPE film. 7th, the top most layer
shall be finished with brick tiles of class designation 10 grouted with cement
mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing
compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1
cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid
for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 30 sqm
MATERIAL
APP modified polymeric felt (two
layers) 1.5 mm thick = 2x30 = 60 sqm
+ Add 10% wastage = 6 sqm.
Total = 66 sqm
8200 A.P.P. modified polymeric felt
(two layers) 1.5 mm thick sqm 66.00 80.00 5280.00
0316 Bitumen solution primer of approved
quality litre 12.00 47.00 564.00
0.4x30 = 12
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.108 34790.00 3757.32
3x36 =108 kg = 0.108 tonne
2211 Carriage of Tar bitumen tonne 0.12 163.93 19.67
9977 Carriage of polymeric felt L.S. 7.80 2.12 16.54
0370 Coal (steam) quintal 0.174 440.00 76.56
2200 Carriage of steam coal tonne 0.0174 187.35 3.26
9999 Preparing roof surface, cutting grooves
and making good the same L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 2.16 714.00 1542.24
0114 Beldar day 3.24 645.00 2089.80
0130 Mistry day 0.18 784.00 141.12
9999 Sundries, brushes etc L.S. 6.76 2.12 14.33
TOTAL 13790.08 W
Add 1 % Water charges on "W" 137.90
TOTAL 13927.99 X
Add GST on "X" (multiplying
factor 0.1405) 1956.88
TOTAL 15884.87 Y
Add 15% CPOH on "Y" 2382.73
TOTAL 18267.60 Z
Add Cess @ 1% on "Z" 182.68
Cost for 30 sqm 18450.27
Cost for 1 sqm 615.01
Say 615.00
SUB HEAD : 14- REPAIRS TO BUILDING 1151
14.87 Providing and laying in situ five course water proofing treatment with APP
(Atactic Polypropylene) modified Polymeric memberane over roof consisting
of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding
material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/
25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric
membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers
prefabricated with centre core as 100 micron HMHDPE film sandwiched on both
sides with polymeric mix and the polymeric mix is protected on both side with
20 micron HMHDPE film. 5th, the top most layer shall be finished with brick
tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine
sand) mixed with 2% integral water proofing compound by weight of cement
over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished
neat (item of laying brick tiles shall be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 30 sqm
MATERIAL
APP modified polymeric felt (two layers)
2.0 mm thick = 30 sqm
Add 10% wastage = 3 sqm
Total = 33 sqm
8201 A.P.P. modified polymeric felt
(two layers) 2 mm thick sqm 33.00 120.00 3960.00
0316 Bitumen solution primer of approved
quality litre 12.00 47.00 564.00
0.4x30 = 12
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.072 34790.00 2504.88
1.20x30x2 =72 kg = 0.072 tonne
2211 Carriage of Tar bitumen tonne 0.084 163.93 13.77
9977 Carriage of polymeric felt L.S. 7.80 2.12 16.54
0370 Coal (steam) quintal 0.174 440.00 76.56
2200 Carriage of steam coal tonne 0.0174 187.35 3.26
9999 Preparing roof surface, cutting grooves
and making good the same L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 1.58 714.00 1128.12
0114 Beldar day 2.37 645.00 1528.65
0130 Mistry day 0.13 784.00 101.92
9999 Sundries, brushes etc L.S. 6.76 2.12 14.33
TOTAL 10197.27 W
Add 1 % Water charges on "W" 101.97
TOTAL 10299.25 X
Add GST on "X" (multiplying
factor 0.1405) 1447.04
TOTAL 11746.29 Y
Add 15% CPOH on "Y" 1761.94
TOTAL 13508.23 Z
Add Cess @ 1% on "Z" 135.08
Cost for 30 sqm 13643.32
Cost for 1 sqm 454.78
Say 454.80
SUB HEAD : 14- REPAIRS TO BUILDING 1152
14.88 Providing and laying in situ seven course water proofing treatment with APP
(Atactic Polypropylene) modified Polymeric memberane over roof consisting
of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of
bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of
grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane
APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/sqm weight
consisting of five layers prefabricated with centre core as 100 micron HMHDPE
film sandwiched on both sides with polymeric mix and the polymeric mix is
protected on both side with 20 micron HMHDPE film. 7th, the top most layer
shall be finished with brick tiles of class designation 10 grouted with cement
mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing
compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1
cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid
for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 30 sqm
MATERIAL
APP modified polymeric felt (two layers)
2.0 mm thick = 2x30 = 60 sqm
Add 10% wastage = 6 sqm
Total = 66 sqm
8201 A.P.P. modified polymeric felt
(two layers) 2 mm thick sqm 66.00 120.00 7920.00
0316 Bitumen solution primer of approved
quality litre 12.00 47.00 564.00
0.4x30 = 12
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.108 34790.00 3757.32
3course x 36 = 108 kg = 0.108 tonne
2211 Carriage of Tar bitumen tonne 0.12 163.93 19.67
9977 Carriage of polymeric felt L.S. 7.80 2.12 16.54
0370 Coal (steam) quintal 0.174 440.00 76.56
2200 Carriage of steam coal tonne 0.0174 187.35 3.26
9999 Preparing roof surface, cutting grooves
and making good the same L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 2.16 714.00 1542.24
0114 Beldar day 3.24 645.00 2089.80
0130 Mistry day 0.18 784.00 141.12
9999 Sundries, brushes etc L.S. 6.76 2.12 14.33
TOTAL 16430.08 W
Add 1 % Water charges on "W" 164.30
TOTAL 16594.39 X
Add GST on "X" (multiplying
factor 0.1405) 2331.51
TOTAL 18925.90 Y
Add 15% CPOH on "Y" 2838.88
TOTAL 21764.78 Z
Add Cess @ 1% on "Z" 217.65
Cost for 30 sqm 21982.43
Cost for 1 sqm 732.75
Say 732.75
SUB HEAD : 14- REPAIRS TO BUILDING 1153
14.89 Providing and fixing APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 2 mm thick water proofing membrane, black finished
reinforced with glass fibre matt consisting of a coat of bitumen primer for
bitumen membrane @ 0.40 litre/sqm by the same membrance manufacture of
density at 25°C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer
coat the layer of membrane shall be laid using Butane torch and sealing all
joints etc., and preparing the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint strength in longitudinal
and transverse direction at 23°C as 350/300 N/ 5 cm. Tear strength in longitudinal
and transverse direction as 60/80N. Softening point of membrane not less than
150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM,
D - 5147. The laying of membrane shall be got done through the authorised
applicator of the manufacture of membrane.
14.89.1 2mm (for corrugated roof sheets)
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
MATERIAL
A.P.P. modified 2 mm thick = 30 sqm
Add 10% for wastage - 3 sqm
Total= 33 sqm
8203 A.P.P. modified 2 mm thick membrance
reinforced with glass fibre matt sqm 33.00 130.00 4290.00
8206 Bitumen primer for bitumen membrance litre 12.00 85.00 1020.00
2211 Carriage of Tar bitumen tonne 0.012 163.93 1.97
9977 Carriage of bitumen membrance L.S. 7.80 2.12 16.54
1241 Commercial LPG in cylinder kg 7.00 84.00 588.00
9999 Preparing roof surface, cutting grooves L.S. 49.53 2.12 105.00
LABOUR
0159 Skilled torch operator for laying tack day 2.16 784.00 1693.44
0130 Mistry day 0.18 784.00 141.12
0114 Beldar day 3.24 645.00 2089.80
9999 Sundries, brushes, bitumen torch etc L.S. 23.40 2.12 49.61
TOTAL 9995.47 W
Add 1 % Water charges on "W" 99.95
TOTAL 10095.43 X
Add GST on "X" (multiplying
factor 0.1405) 1418.41
TOTAL 11513.84 Y
Add 15% CPOH on "Y" 1727.08
TOTAL 13240.91 Z
Add Cess @ 1% on "Z" 132.41
Cost for 30 sqm 13373.32
Cost for 1 sqm 445.78
Say 445.80
14.90 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer, 3 mm thick water proofing membrane, black finished
reinforced with glass fibre matt consisting of a coat of bitumen primer for
bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of
density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer
coat the layer of membrane shall be laid using butane torch and sealing all
joints etc., and preparing the surface complete. The vital physical and chemical
SUB HEAD : 14- REPAIRS TO BUILDING 1154
parameters of the membrane shall be as under : Joint strength in longitudinal
and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal
and transverse direction as 60/80N. Softening point of membrane not less than
150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM,
D - 5147. The laying of membrane shall be got done through the authorised
applicator of the manufacturer of membrane :
14.90.1 3 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
MATERIAL
A.P.P. modified 3 mm thick = 30 sqm
Add 10% for wastage - 3 sqm
Total = 33 sqm
8204 A.P.P. modified 3 mm thick membrance
reinforced with glass fibre matt sqm 33.00 190.00 6270.00
8206 Bitumen primer for bitumen membrance litre 12.00 85.00 1020.00
2211 Carriage of Tar bitumen tonne 0.012 163.93 1.97
9977 Carriage of bitumen membrance L.S. 7.80 2.12 16.54
1241 Commercial LPG in cylinder kg 7.00 84.00 588.00
9999 Preparing roof surface, cutting grooves L.S. 49.53 2.12 105.00
LABOUR
0159 Skilled torch operator for laying tack day 2.16 784.00 1693.44
0130 Mistry day 0.18 784.00 141.12
0114 Beldar day 3.24 645.00 2089.80
9999 Sundries, brushes, bitumen torch etc L.S. 23.40 2.12 49.61
TOTAL 11975.47 W
Add 1 % Water charges on "W" 119.75
TOTAL 12095.23 X
Add GST on "X" (multiplying
factor 0.1405) 1699.38
TOTAL 13794.61 Y
Add 15% CPOH on "Y" 2069.19
TOTAL 15863.80 Z
Add Cess @ 1% on "Z" 158.64
Cost for 30 sqm 16022.44
Cost for 1 sqm 534.08
Say 534.10
14.91 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 3 mm thick water proofing membrane, black finished
reinforced with non-woven polyester matt consisting of a coat of bitumen primer
for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of
density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer
coat the layer of membrane shall be laid using Butane Torch and sealing all
joints etc, and preparing the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint strength in longitudinal
and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal
and transverse direction as 300/250N. Softening point of membrane not less
than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with
ASTM, D - 5147. The laying of membrane shall be got done through the authorised
applicator of the manufacturer of membrane :
SUB HEAD : 14- REPAIRS TO BUILDING 1155
14.91.1 3 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
MATERIAL
A.P.P. modified 3 mm thick - 30 sqm
Add 10% for wastage - 3 sqm
Total = 33 sqm
8205 A.P.P. modified 3 mm thick membrance
reinforced with polyster matt sqm 33.00 210.00 6930.00
8206 Bitumen primer for bitumen membrance litre 12.00 85.00 1020.00
2211 Carriage of Tar bitumen tonne 0.012 163.93 1.97
9977 Carriage of bitumen membrance L.S. 7.80 2.12 16.54
Fuel
1241 Commercial LPG in cylinder kg 7.00 84.00 588.00
9999 Preparing roof surface, cutting grooves L.S. 49.53 2.12 105.00
LABOUR
0159 Skilled torch operator for laying tack day 2.16 784.00 1693.44
0130 Mistry day 0.18 784.00 141.12
0114 Beldar day 3.24 645.00 2089.80
9999 Sundries, brushes, bitumen torch etc L.S. 23.4 2.12 49.61
TOTAL 12635.47 W
Add 1 % Water charges on "W" 126.35
TOTAL 12761.83 X
Add GST on "X" (multiplying
factor 0.1405) 1793.04
TOTAL 14554.87 Y
Add 15% CPOH on "Y" 2183.23
TOTAL 16738.10 Z
Add Cess @ 1% on "Z" 167.38
Cost for 30 sqm 16905.48
Cost for 1 sqm 563.52
Say 563.50
14.92 Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%
polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent
touch by heating the membrane by Butane Torch as per manufactures
recommendation.
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
MATERIAL
Geotextile 120 gsm membrance - 30 sqm
Add 5% for wastage - 1.50 sqm
Total= 31.50 sqm
8207 Geotextile 120 gsm membrance sqm 31.50 45.00 1417.50
9977 Carriage of Geotextile L.S. 7.80 2.12 16.54
LABOUR
0159 Skilled torch operator for laying tack day 0.43 784.00 337.12
or fitter 2.16 / 5 = 0.43
0130 Mistry day 0.04 784.00 31.36
0.18 / 5 = 0.04
SUB HEAD : 14- REPAIRS TO BUILDING 1156
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.65 645.00 419.25
3.24-5 / 0.65
9999 Sundries, torch, LPG etc L.S. 46.80 2.12 99.22
TOTAL 2320.98 W
Add 1 % Water charges on "W" 23.21
TOTAL 2344.19 X
Add GST on "X" (multiplying
factor 0.1405) 329.36
TOTAL 2673.55 Y
Add 15% CPOH on "Y" 401.03
TOTAL 3074.58 Z
Add Cess @ 1% on "Z" 30.75
Cost for 30 sqm 3105.33
Cost for 1 sqm 103.51
Say 103.50
14.93 Providing round the clock security guard without gun for watch & ward of
Government premises and its all belongings by deploying neatly dressed
security guards in 8 hour's shift including necessary T&P like torch, lathi and
uniform etc.complete,as per the direction of Engineer-in-charge. (One job means
8 hour's duty).
Code Description Unit Quantity Rate Amount
Details of cost for 1 job (8hour’s duty)
0164 Security guard (without gun) day 1.00 784.00 784.00
9999 Lathi,torch,dress & other sundries L.S. 10.00 2.12 21.20
TOTAL 805.20 W
Add 1 % Water charges on “W” 8.05
TOTAL 813.25 X
Add GST on “X” (multiplying
factor 0.1405) 114.26
TOTAL 927.51 Y
Add 15% CPOH on “Y” 139.13
TOTAL 1066.64 Z
Add Cess @ 1% on “Z” 10.67
Cost of 1 job 1077.31
Say 1077.30
14.94 Providing round the clock security guard with gun for watch & ward of
Government premises and its all belongings by deploying neatly dressed
security guards in 8 hour's shift including necessary T&P like torch, lathi and
uniform etc.complete, as per the direction of Engineer-in-charge.(One job means
8 hour's duty).
Code Description Unit Quantity Rate Amount
Details of cost for 1 job (8hour's duty)
0165 Security guard (with gun) day 1.00 853.00 853.00
SUB HEAD : 14- REPAIRS TO BUILDING 1157
Code Description Unit Quantity Rate Amount
9999 Lathi,torch,uniform,wooden stick &
other miscellaneous items L.S. 10.00 2.12 21.20
TOTAL 874.20 W
Add 1 % Water charges on "W" 8.74
TOTAL 882.94 X
Add GST on "X" (multiplying
factor 0.1405) 124.05
TOTAL 1007.00 Y
Add 15% CPOH on "Y" 151.05
TOTAL 1158.04 Z
Add Cess @ 1% on "Z" 11.58
Cost of 1 job 1169.63
Say 1169.65
SUB HEAD : 14- REPAIRS TO BUILDING 1158
SUB HEAD : 15.0
DISMANTLING
AND
DEMOLISHING
1159
15.1 Demolishing lime concrete manually/ by mechanical means and disposal of
material within 50 metres lead as per direction of Engineer- in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.44 645.00 283.80
0115 Coolie day 0.37 645.00 238.65
9999 Sundries L.S. 1.04 2.12 2.20
TOTAL 524.65 W
Add 1 % Water charges on “W” 5.25
TOTAL 529.90 X
Add GST on “X” (multiplying
factor 0.1405) 74.45
TOTAL 604.35 Y
Add 15% CPOH on “Y” 90.65
TOTAL 695.01 Z
Add Cess @ 1% on “Z” 6.95
Cost of 1.00 cum 701.96
Say 701.95
15.2 Demolishing cement concrete manually/ by mechanical means including
disposal of material within 50 metres lead as per direction of Engineer - in -
charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.59 645.00 1025.55
0115 Coolie day 0.72 645.00 464.40
9999 Sundries L.S. 4.81 2.12 10.20
TOTAL 1500.15 W
Add 1 % Water charges on "W" 15.00
TOTAL 1515.15 X
Add GST on "X" (multiplying
factor 0.1405) 212.88
TOTAL 1728.03 Y
Add 15% CPOH on "Y" 259.20
TOTAL 1987.23 Z
Add Cess @ 1% on "Z" 19.87
Cost of 1.00 cum 2007.10
Say 2007.10
15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.88 645.00 567.60
0115 Coolie day 0.55 645.00 354.75
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1161
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 1.95 2.12 4.13
TOTAL 926.48 W
Add 1 % Water charges on “W” 9.26
TOTAL 935.75 X
Add GST on “X” (multiplying
factor 0.1405) 131.47
TOTAL 1067.22 Y
Add 15% CPOH on “Y” 160.08
TOTAL 1227.30 Z
Add Cess @ 1% on “Z” 12.27
Cost of 1.00 cum 1239.58
Say 1239.60
15.3 Demolishing R.C.C. work manually/ by mechanical means including stacking
of steel bars and disposal of unserviceable material within 50 metres lead as
per direction of Engineer - in- charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 2.65 645.00 1709.25
0115 Coolie day 0.72 645.00 464.40
9999 Sundries L.S. 7.02 2.12 14.88
TOTAL 2188.53 W
Add 1 % Water charges on “W” 21.89
TOTAL 2210.42 X
Add GST on “X” (multiplying
factor 0.1405) 310.56
TOTAL 2520.98 Y
Add 15% CPOH on “Y” 378.15
TOTAL 2899.13 Z
Add Cess @ 1% on “Z” 28.99
Cost of 1.00 cum 2928.12
Say 2928.10
15.4 Demolishing R.B. work manually/ by mechanical means including stacking of
steel bars and disposal of unserviceable material within 50 metres lead as per
direction of Engineer-in- charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 2.12 645.00 1367.40
0115 Coolie day 0.90 645.00 580.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1162
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 4.68 2.12 9.92
TOTAL 1957.82 W
Add 1 % Water charges on "W" 19.58
TOTAL 1977.40 X
Add GST on "X" (multiplying
factor 0.1405) 277.82
TOTAL 2255.22 Y
Add 15% CPOH on "Y" 338.28
TOTAL 2593.51 Z
Add Cess @ 1% on "Z" 25.94
Cost of 1.00 cum 2619.44
Say 2619.45
15.5 Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C.
or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or
R.B. work) as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 sqm
R.C.C. or R.B. workReinforced area
considering 1% reinforcement = 0.01sqm
LABOUR
For cutting 0.01 sqm reinforcement
0103 Blacksmith 2nd class day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 707.89 W
Add 1 % Water charges on "W" 7.08
TOTAL 714.97 X
Add GST on "X" (multiplying
factor 0.1405) 100.45
TOTAL 815.42 Y
Add 15% CPOH on "Y" 122.31
TOTAL 937.73 Z
Add Cess @ 1% on "Z" 9.38
Cost of 1.00 sqm 947.11
Say 947.10
15.6 Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or
R.B. work.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 Nos
6 metres long 16 mm dia bars @
1.58 kg/metre
Total weight = 94.80 kg = 0.948 quintal
LABOUR
0103 Blacksmith 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.50 645.00 322.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1163
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 529.39 W
Add 1 % Water charges on "W" 5.29
TOTAL 534.68 X
Add GST on "X" (multiplying
factor 0.1405) 75.12
TOTAL 609.80 Y
Add 15% CPOH on "Y" 91.47
TOTAL 701.27 Z
Add Cess @ 1% on "Z" 7.01
Cost of 94.80 kg 708.29
Cost of 1.00 kg 7.47
Say 7.45
15.7 Demolishing brick work manually/ by mechanical means including stacking of
serviceable material and disposal of unserviceable material within 50 metres
lead as per direction of Engineer-in-charge.
15.7.1 In mud mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.30 645.00 193.50
0115 Coolie day 0.37 645.00 238.65
9999 Sundries L.S. 1.04 2.12 2.20
TOTAL 434.35 W
Add 1 % Water charges on “W” 4.34
TOTAL 438.70 X
Add GST on “X” (multiplying
factor 0.1405) 61.64
TOTAL 500.34 Y
Add 15% CPOH on “Y” 75.05
TOTAL 575.39 Z
Add Cess @ 1% on “Z” 5.75
Cost of 1.00 cum 581.14
Say 581.15
15.7.2 In lime mortar with old mughal bricks
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.24 645.00 799.80
0115 Coolie day 0.46 645.00 296.70
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1164
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 1.04 2.12 2.20
TOTAL 1098.70 W
Add 1 % Water charges on "W" 10.99
TOTAL 1109.69 X
Add GST on "X" (multiplying
factor 0.1405) 155.91
TOTAL 1265.60 Y
Add 15% CPOH on "Y" 189.84
TOTAL 1455.44 Z
Add Cess @ 1% on "Z" 14.55
Cost of 1.00 cum 1470.00
Say 1470.00
15.7.3 In lime mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.44 645.00 283.80
0115 Coolie day 0.37 645.00 238.65
9999 Sundries L.S. 1.04 2.12 2.20
TOTAL 524.65 W
Add 1 % Water charges on "W" 5.25
TOTAL 529.90 X
Add GST on "X" (multiplying
factor 0.1405) 74.45
TOTAL 604.35 Y
Add 15% CPOH on "Y" 90.65
TOTAL 695.01 Z
Add Cess @ 1% on "Z" 6.95
Cost of 1.00 cum 701.96
Say 701.95
15.7.4 In cement mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.06 645.00 683.70
0115 Coolie day 0.90 645.00 580.50
9999 Sundries L.S. 2.47 2.12 5.24
TOTAL 1269.44 W
Add 1 % Water charges on “W” 12.69
TOTAL 1282.13 X
Add GST on “X” (multiplying
factor 0.1405) 180.14
TOTAL 1462.27 Y
Add 15% CPOH on “Y” 219.34
TOTAL 1681.61 Z
Add Cess @ 1% on “Z” 16.82
Cost of 1.00 cum 1698.43
Say 1698.45
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1165
15.8 Removing mortar from bricks and cleaning bricks including stacking within a
lead of 50 m (stacks of cleaned bricks shall be measured):
15.8.1 From brick work in mud mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1000 Nos
LABOUR
0114 Beldar day 2.40 645.00 1548.00
0115 Coolie day 1.60 645.00 1032.00
0124 Mason (brick layer) 2nd class day 0.40 714.00 285.60
9999 Sundries L.S. 1.82 2.12 3.86
TOTAL 2869.46 W
Add 1 % Water charges on "W" 28.69
TOTAL 2898.15 X
Add GST on "X" (multiplying
factor 0.1405) 407.19
TOTAL 3305.34 Y
Add 15% CPOH on "Y" 495.80
TOTAL 3801.14 Z
Add Cess @ 1% on "Z" 38.01
Cost of 1000 Nos 3839.16
Say 3839.15
15.8.2 From brick work in lime mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1000 Nos
LABOUR
0114 Beldar day 2.80 645.00 1806.00
0115 Coolie day 1.40 645.00 903.00
0124 Mason (brick layer) 2nd class day 0.80 714.00 571.20
9999 Sundries L.S. 8.97 2.12 19.02
TOTAL 3299.22 W
Add 1 % Water charges on "W" 32.99
TOTAL 3332.21 X
Add GST on "X" (multiplying
factor 0.1405) 468.18
TOTAL 3800.38 Y
Add 15% CPOH on "Y" 570.06
TOTAL 4370.44 Z
Add Cess @ 1% on "Z" 43.70
Cost of 1000 Nos 4414.15
Say 4414.15
15.8.3 From brick work in cement mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1000 Nos
LABOUR
0114 Beldar day 3.50 645.00 2257.50
0115 Coolie day 1.50 645.00 967.50
0124 Mason (brick layer) 2nd class day 1.24 714.00 885.36
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1166
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 4127.45 W
Add 1 % Water charges on “W” 41.27
TOTAL 4168.72 X
Add GST on “X” (multiplying
factor 0.1405) 585.71
TOTAL 4754.43 Y
Add 15% CPOH on “Y” 713.16
TOTAL 5467.59 Z
Add Cess @ 1% on “Z” 54.68
Cost of 1000 Nos 5522.27
Say 5522.25
15.9 Demolishing stone rubble masonry manually/ by mechanical means including
stacking of serviceable material and disposal of unserviceable material within
50 metres lead as per direction of Engineer-in-charge :
15.9.1 In lime mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.61 645.00 393.45
0115 Coolie day 0.49 645.00 316.05
9999 Sundries L.S. 1.95 2.12 4.13
TOTAL 713.63 W
Add 1 % Water charges on “W” 7.14
TOTAL 720.77 X
Add GST on “X” (multiplying
factor 0.1405) 101.27
TOTAL 822.04 Y
Add 15% CPOH on “Y” 123.31
TOTAL 945.34 Z
Add Cess @ 1% on “Z” 9.45
Cost of 1.00 cum 954.80
Say 954.80
15.9.2 In cement mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.30 645.00 838.50
0115 Coolie day 1.04 645.00 670.80
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1167
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 1515.09 W
Add 1 % Water charges on "W" 15.15
TOTAL 1530.24 X
Add GST on "X" (multiplying
factor 0.1405) 215.00
TOTAL 1745.24 Y
Add 15% CPOH on "Y" 261.79
TOTAL 2007.02 Z
Add Cess @ 1% on "Z" 20.07
Cost of 1.00 cum 2027.09
Say 2027.10
15.10 Dismantling dressed stone work ashlar face stone work, marble work or
precast concrete work manually/ by mechanical means including stacking of
serviceable and disposal of unserviceable material within 50 metres lead as
per direction of Engineer-in-charge :
15.10.1 In lime mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.78 645.00 503.10
0115 Coolie day 0.61 645.00 393.45
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 902.34 W
Add 1 % Water charges on "W" 9.02
TOTAL 911.36 X
Add GST on "X" (multiplying
factor 0.1405) 128.05
TOTAL 1039.41 Y
Add 15% CPOH on "Y" 155.91
TOTAL 1195.32 Z
Add Cess @ 1% on "Z" 11.95
Cost of 1.00 cum 1207.27
Say 1207.25
15.10.2 In cement mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.55 645.00 999.75
0115 Coolie day 1.19 645.00 767.55
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1168
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 1773.09 W
Add 1 % Water charges on “W” 17.73
TOTAL 1790.82 X
Add GST on “X” (multiplying
factor 0.1405) 251.61
TOTAL 2042.43 Y
Add 15% CPOH on “Y” 306.36
TOTAL 2348.79 Z
Add Cess @ 1% on “Z” 23.49
Cost of 1.00 cum 2372.28
Say 2372.30
15.11 Removing mortar from and cleaning stones and concrete articles (net quantity
of stacks of cleaned materials will be measured):
15.11.1 In lime mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0114 Beldar day 0.20 645.00 129.00
0115 Coolie day 0.20 645.00 129.00
9999 Sundries L.S. 0.52 2.12 1.10
TOTAL 294.80 W
Add 1 % Water charges on “W” 2.95
TOTAL 297.75 X
Add GST on “X” (multiplying
factor 0.1405) 41.83
TOTAL 339.58 Y
Add 15% CPOH on “Y” 50.94
TOTAL 390.52 Z
Add Cess @ 1% on “Z” 3.91
Cost of 1.00 cum 394.43
Say 394.45
15.11.2 In cement mortar
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0114 Beldar day 0.40 645.00 258.00
0115 Coolie day 0.20 645.00 129.00
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1169
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 0.91 2.12 1.93
TOTAL 424.63 W
Add 1 % Water charges on "W" 4.25
TOTAL 428.88 X
Add GST on "X" (multiplying
factor 0.1405) 60.26
TOTAL 489.13 Y
Add 15% CPOH on "Y" 73.37
TOTAL 562.50 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1.00 cum 568.13
Say 568.15
15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter
including chowkhats, architrave, holdfasts etc. complete and stacking within
50 metres lead :
15.12.1 Of area 3 sq. metres and below
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.18 645.00 116.10
0103 Blacksmith 2nd class day 0.05 714.00 35.70
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 226.23 W
Add 1 % Water charges on "W" 2.26
TOTAL 228.49 X
Add GST on "X" (multiplying
factor 0.1405) 32.10
TOTAL 260.60 Y
Add 15% CPOH on "Y" 39.09
TOTAL 299.69 Z
Add Cess @ 1% on "Z" 3.00
Cost of each 302.68
Say 302.70
15.12.2 Of area beyond 3 sq. metres
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0124 Mason (brick layer) 2nd class day 0.13 714.00 92.82
0114 Beldar day 0.25 645.00 161.25
0103 Blacksmith 2nd class day 0.07 714.00 49.98
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1170
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 309.84 W
Add 1 % Water charges on "W" 3.10
TOTAL 312.94 X
Add GST on "X" (multiplying
factor 0.1405) 43.97
TOTAL 356.90 Y
Add 15% CPOH on "Y" 53.54
TOTAL 410.44 Z
Add Cess @ 1% on "Z" 4.10
Cost of each 414.54
Say 414.55
15.13 Taking out doors, windows and clerestory window shutters (steel or wood)
including stacking within 50 metres lead :
15.13.1 Of area 3 sq. metres and below
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0112 Carpenter 2nd class day 0.05 714.00 35.70
0114 Beldar day 0.08 645.00 51.60
9999 Sundries L.S. 0.52 2.12 1.10
TOTAL 88.40 W
Add 1 % Water charges on "W" 0.88
TOTAL 89.29 X
Add GST on "X" (multiplying
factor 0.1405) 12.54
TOTAL 101.83 Y
Add 15% CPOH on "Y" 15.27
TOTAL 117.11 Z
Add Cess @ 1% on "Z" 1.17
Cost of each 118.28
Say 118.30
15.13.2 Of area beyond 3 sq. metres
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0112 Carpenter 2nd class day 0.07 714.00 49.98
0114 Beldar day 0.10 645.00 64.50
9999 Sundries L.S. 0.91 2.12 1.93
TOTAL 116.41 W
Add 1 % Water charges on "W" 1.16
TOTAL 117.57 X
Add GST on "X" (multiplying
factor 0.1405) 16.52
TOTAL 134.09 Y
Add 15% CPOH on "Y" 20.11
TOTAL 154.21 Z
Add Cess @ 1% on "Z" 1.54
Cost of each 155.75
Say 155.75
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1171
15.14 Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres
span and 5 metres height including stacking the material within 50 metres
lead :
15.14.1 Of sectional area 40 square centimetres and above
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 2746.39 W
Add 1 % Water charges on "W" 27.46
TOTAL 2773.85 X
Add GST on "X" (multiplying
factor 0.1405) 389.73
TOTAL 3163.58 Y
Add 15% CPOH on "Y" 474.54
TOTAL 3638.11 Z
Add Cess @ 1% on "Z" 36.38
Cost of 1.00 cum 3674.49
Say 3674.50
15.14.2 Of sectional area below 40 square centimetres
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
0112 Carpenter 2nd class day 0.08 714.00 57.12
0114 Beldar day 0.08 645.00 51.60
9999 Sundries L.S. 0.52 2.12 1.10
TOTAL 109.82 W
Add 1 % Water charges on "W" 1.10
TOTAL 110.92 X
Add GST on "X" (multiplying
factor 0.1405) 15.58
TOTAL 126.50 Y
Add 15% CPOH on "Y" 18.98
TOTAL 145.48 Z
Add Cess @ 1% on "Z" 1.45
Cost of 10.00 metre 146.94
Cost of 1.00 metre 14.69
Say 14.70
15.15 Extra for dismantling trusses, rafters, purlins etc. of wood work for every
additional span of one metre or part thereof beyond 10 metres :
15.15.1 Of sectional area 40 square centimetres and above
Code Description Unit Quantity Rate Amount
Detail of cost for 1cum for every
additional span of 1 metre
LABOUR
0103 Blacksmith 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.30 645.00 193.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1172
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 364.69 W
Add 1 % Water charges on “W” 3.65
TOTAL 368.33 X
Add GST on “X” (multiplying
factor 0.1405) 51.75
TOTAL 420.08 Y
Add 15% CPOH on “Y” 63.01
TOTAL 483.10 Z
Add Cess @ 1% on “Z” 4.83
Cost of 1.00 cum per metre span 487.93
Say 487.95
15.15.2 Of sectional area below 40 square centimetres
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre for every
additional span of 1 metre
LABOUR
0103 Blacksmith 2nd class day 0.006 714.00 4.28
0114 Beldar day 0.008 645.00 5.16
9999 Sundries L.S. 0.39 2.12 0.83
TOTAL 10.27 W
Add 1 % Water charges on "W" 0.10
TOTAL 10.37 X
Add GST on "X" (multiplying
factor 0.1405) 1.46
TOTAL 11.83 Y
Add 15% CPOH on "Y" 1.77
TOTAL 13.61 Z
Add Cess @ 1% on "Z" 0.14
Cost of 10.00 metre per metre span 13.74
Cost of 1.00 metre per metre span 1.37
Say 1.35
15.16 Extra for dismantling trusses, rafters, purlins etc. of wood work for every
additional height of one metre or part thereof beyond 5 metres :
15.16.1 Of sectional area 40 square centimetres and above
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum for every
additional height of 1 metre
LABOUR
0103 Blacksmith 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.50 645.00 322.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1173
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 529.39 W
Add 1 % Water charges on "W" 5.29
TOTAL 534.68 X
Add GST on "X" (multiplying
factor 0.1405) 75.12
TOTAL 609.80 Y
Add 15% CPOH on "Y" 91.47
TOTAL 701.27 Z
Add Cess @ 1% on "Z" 7.01
Cost of 1.00 cum per metre height 708.29
Say 708.30
15.16.2 Of sectional area below 40 square centimetres
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre for every
additional height of 1 metre
LABOUR
0103 Blacksmith 2nd class day 0.01 714.00 7.14
0114 Beldar day 0.02 645.00 12.90
9999 Sundries L.S. 0.39 2.12 0.83
TOTAL 20.87 W
Add 1 % Water charges on "W" 0.21
TOTAL 21.08 X
Add GST on "X" (multiplying
factor 0.1405) 2.96
TOTAL 24.04 Y
Add 15% CPOH on "Y" 3.61
TOTAL 27.64 Z
Add Cess @ 1% on "Z" 0.28
Cost of 10.00 metre per metre height 27.92
Cost of 1.00 metre per metre height 2.79
Say 2.80
15.17 Dismantling steel work in single sections including dismembering and stacking
within 50 metres lead in:
15.17.1 R.S. Joists
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0103 Blacksmith 2nd class day 0.05 714.00 35.70
0100 Bandhani day 0.10 714.00 71.40
0114 Beldar day 0.15 645.00 96.75
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1174
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 209.64 W
Add 1 % Water charges on "W" 2.10
TOTAL 211.73 X
Add GST on "X" (multiplying
factor 0.1405) 29.75
TOTAL 241.48 Y
Add 15% CPOH on "Y" 36.22
TOTAL 277.70 Z
Add Cess @ 1% on "Z" 2.78
Cost of 1.00 quintal 280.48
Cost of 1.00 kg 2.80
Say 2.80
15.17.2 Channels, angles, tees and flats
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0103 Blacksmith 2nd class day 0.05 714.00 35.70
0100 Bandhani day 0.05 714.00 35.70
0114 Beldar day 0.10 645.00 64.50
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 141.69 W
Add 1 % Water charges on "W" 1.42
TOTAL 143.10 X
Add GST on "X" (multiplying
factor 0.1405) 20.11
TOTAL 163.21 Y
Add 15% CPOH on "Y" 24.48
TOTAL 187.69 Z
Add Cess @ 1% on "Z" 1.88
Cost of 1.00 quintal 189.57
Cost of 1.00 kg 1.90
Say 1.90
15.18 Dismantling steel work in built up sections in angles, tees, flats and channels
including all gusset plates, bolts, nuts, cutting rivets, welding etc. including
dismembering and stacking within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0103 Blacksmith 2nd class day 0.15 714.00 107.10
0100 Bandhani day 0.10 714.00 71.40
0114 Beldar day 0.25 645.00 161.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1175
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 4.16 2.12 8.82
TOTAL 348.57 W
Add 1 % Water charges on "W" 3.49
TOTAL 352.05 X
Add GST on "X" (multiplying
factor 0.1405) 49.46
TOTAL 401.52 Y
Add 15% CPOH on "Y" 60.23
TOTAL 461.75 Z
Add Cess @ 1% on "Z" 4.62
Cost of 1.00 quintal 466.36
Cost of 1.00 kg 4.66
Say 4.65
15.19 Dismantling steel work manually/ by mechanical means in built up sections
without dismembering and stacking within 50 metres lead as per direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0100 Bandhani day 0.10 714.00 71.40
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 238.44 W
Add 1 % Water charges on "W" 2.38
TOTAL 240.82 X
Add GST on "X" (multiplying
factor 0.1405) 33.84
TOTAL 274.66 Y
Add 15% CPOH on "Y" 41.20
TOTAL 315.86 Z
Add Cess @ 1% on "Z" 3.16
Cost of 1.00 quintal 319.01
Cost of 1.00 kg 3.19
Say 3.20
15.20 Extra for dismantling trusses, rafters, purlins etc. of steel work for every
additional span of one metre or part thereof beyond 10 metres
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal for every
additional span of 1 metre beyond
10 metre
LABOUR
0100 Bandhani day 0.02 714.00 14.28
0114 Beldar day 0.06 645.00 38.70
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1176
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 0.39 2.12 0.83
TOTAL 53.81 W
Add 1 % Water charges on "W" 0.54
TOTAL 54.34 X
Add GST on "X" (multiplying
factor 0.1405) 7.64
TOTAL 61.98 Y
Add 15% CPOH on "Y" 9.30
TOTAL 71.28 Z
Add Cess @ 1% on "Z" 0.71
Cost of 1.00 quintal per metre span 71.99
Cost of 1.00 kg per metre span 0.72
Say 0.70
15.21 Extra for dismantling trusses, rafters, purlins etc. of steel work for every
additional height of one metre or part thereof beyond 5 metres.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal for every
additional height of 1 metre beyond
5 metre
LABOUR
0100 Bandhani day 0.02 714.00 14.28
0114 Beldar day 0.06 645.00 38.70
9999 Sundries L.S. 0.39 2.12 0.83
TOTAL 53.81 W
Add 1 % Water charges on "W" 0.54
TOTAL 54.34 X
Add GST on "X" (multiplying
factor 0.1405) 7.64
TOTAL 61.98 Y
Add 15% CPOH on "Y" 9.30
TOTAL 71.28 Z
Add Cess @ 1% on "Z" 0.71
Cost of 1.00 quintal per metre height 71.99
Cost of 1.00 kg per metre height 0.72
Say 0.70
15.22 Extra for marking of structural steel work required to be re-erected.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0130 Mistry day 0.20 784.00 156.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 285.80 W
Add 1 % Water charges on "W" 2.86
TOTAL 288.66 X
Add GST on "X" (multiplying
factor 0.1405) 40.56
TOTAL 329.21 Y
Add 15% CPOH on "Y" 49.38
TOTAL 378.60 Z
Add Cess @ 1% on "Z" 3.79
Cost of 1.00 quintal 382.38
Cost of 1.00 kg 3.82
Say 3.80
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1177
15.23 Dismantling tile work in floors and roofs laid in cement mortar including
stacking material within 50 metres lead.
15.23.1 For thickness of tiles 10 mm to 25 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.30 714.00 214.20
0114 Beldar day 0.12 645.00 77.40
0115 Coolie day 0.24 645.00 154.80
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 452.19 W
Add 1 % Water charges on “W” 4.52
TOTAL 456.71 X
Add GST on “X” (multiplying
factor 0.1405) 64.17
TOTAL 520.88 Y
Add 15% CPOH on “Y” 78.13
TOTAL 599.01 Z
Add Cess @ 1% on “Z” 5.99
Cost of 10.00 sqm 605.00
Cost of 1.00 sqm 60.50
Say 60.50
15.23.2 For thickness of tiles above 25 mm and up to 40 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.59 714.00 421.26
0114 Beldar day 0.18 645.00 116.10
0115 Coolie day 0.24 645.00 154.80
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 697.95 W
Add 1 % Water charges on "W" 6.98
TOTAL 704.93 X
Add GST on "X" (multiplying
factor 0.1405) 99.04
TOTAL 803.97 Y
Add 15% CPOH on "Y" 120.60
TOTAL 924.56 Z
Add Cess @ 1% on "Z" 9.25
Cost of 10.00 sqm 933.81
Cost of 1.00 sqm 93.38
Say 93.40
15.24 Demolishing dry brick pitching in floors, drains etc. including stacking of
serviceable material and disposal of unserviceable material within 50 metres
lead :
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.25 645.00 161.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1178
Code Description Unit Quantity Rate Amount
0115 Coolie day 1.00 645.00 645.00
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 812.04 W
Add 1 % Water charges on "W" 8.12
TOTAL 820.16 X
Add GST on "X" (multiplying
factor 0.1405) 115.23
TOTAL 935.39 Y
Add 15% CPOH on "Y" 140.31
TOTAL 1075.70 Z
Add Cess @ 1% on "Z" 10.76
Cost of 1.00 cum 1086.46
Say 1086.45
15.25 Dismantling stone slab flooring laid in cement mortar including stacking of
serviceable material and disposal of unserviceable material within 50 metres
lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 1.77 645.00 1141.65
0115 Coolie day 0.75 645.00 483.75
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1642.49 W
Add 1 % Water charges on "W" 16.42
TOTAL 1658.91 X
Add GST on "X" (multiplying
factor 0.1405) 233.08
TOTAL 1891.99 Y
Add 15% CPOH on "Y" 283.80
TOTAL 2175.79 Z
Add Cess @ 1% on "Z" 21.76
Cost of 10.00 sqm 2197.55
Cost of 1.00 sqm 219.75
Say 219.75
15.26 Demolishing brick tile covering in terracing including stacking of serviceable
material and disposal of unserviceable material within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.54 714.00 385.56
0114 Beldar day 0.16 645.00 103.20
0115 Coolie day 0.24 645.00 154.80
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1179
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.47 2.12 5.24
TOTAL 648.80 W
Add 1 % Water charges on "W" 6.49
TOTAL 655.28 X
Add GST on "X" (multiplying
factor 0.1405) 92.07
TOTAL 747.35 Y
Add 15% CPOH on "Y" 112.10
TOTAL 859.45 Z
Add Cess @ 1% on "Z" 8.59
Cost of 10.00 sqm 868.05
Cost of 1.00 sqm 86.80
Say 86.80
15.27 Demolishing mud phaska in terracing and disposal of material within 50 metres
lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 0.62 645.00 399.90
9999 Sundries L.S. 1.04 2.12 2.20
TOTAL 563.35 W
Add 1 % Water charges on “W” 5.63
TOTAL 568.99 X
Add GST on “X” (multiplying
factor 0.1405) 79.94
TOTAL 648.93 Y
Add 15% CPOH on “Y” 97.34
TOTAL 746.27 Z
Add Cess @ 1% on “Z” 7.46
Cost of 1.00 cum 753.73
Say 753.75
15.28 Dismantling roofing including ridges, hips, valleys and gutters etc., and
stacking the material within 50 metres lead of:
15.28.1 G.S. Sheet
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1180
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 1016.33 W
Add 1 % Water charges on "W" 10.16
TOTAL 1026.49 X
Add GST on "X" (multiplying
factor 0.1405) 144.22
TOTAL 1170.72 Y
Add 15% CPOH on "Y" 175.61
TOTAL 1346.32 Z
Add Cess @ 1% on "Z" 13.46
Cost of 10.00 sqm 1359.79
Cost of 1.00 sqm 135.98
Say 136.00
15.28.2 Asbestos Cement sheet
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 476.60 W
Add 1 % Water charges on "W" 4.77
TOTAL 481.37 X
Add GST on "X" (multiplying
factor 0.1405) 67.63
TOTAL 549.00 Y
Add 15% CPOH on "Y" 82.35
TOTAL 631.35 Z
Add Cess @ 1% on "Z" 6.31
Cost of 10.00 sqm 637.66
Cost of 1.00 sqm 63.77
Say 63.75
15.29 Dismantling stone slab roofing over wooden karries or R.C.C. battens
(dismantling karries and battens to be paid for separately), including stacking
of serviceable material and disposal of unserviceable material within 50 metres
lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 cum
LABOUR
0114 Beldar day 1.77 645.00 1141.65
0115 Coolie day 0.75 645.00 483.75
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1181
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1642.49 W
Add 1 % Water charges on “W” 16.42
TOTAL 1658.91 X
Add GST on “X” (multiplying
factor 0.1405) 233.08
TOTAL 1891.99 Y
Add 15% CPOH on “Y” 283.80
TOTAL 2175.79 Z
Add Cess @ 1% on “Z” 21.76
Cost of 1.00 cum 2197.55
Say 2197.55
15.30 Dismantling jack arch roofing and floors including stacking of serviceable
material and disposal of unserviceable material within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 1.19 645.00 767.55
0115 Coolie day 1.21 645.00 780.45
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1565.09 W
Add 1 % Water charges on "W" 15.65
TOTAL 1580.74 X
Add GST on "X" (multiplying
factor 0.1405) 222.09
TOTAL 1802.83 Y
Add 15% CPOH on "Y" 270.42
TOTAL 2073.26 Z
Add Cess @ 1% on "Z" 20.73
Cost of 10.00 sqm 2093.99
Cost of 1.00 sqm 209.40
Say 209.40
15.31 Dismantling tiled roofing with battens, boarding etc. complete including
stacking of serviceable material and disposal of unserviceable material within
50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 1.73 645.00 1115.85
0115 Coolie day 0.25 645.00 161.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1182
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 1294.19 W
Add 1 % Water charges on "W" 12.94
TOTAL 1307.13 X
Add GST on "X" (multiplying
factor 0.1405) 183.65
TOTAL 1490.78 Y
Add 15% CPOH on "Y" 223.62
TOTAL 1714.40 Z
Add Cess @ 1% on "Z" 17.14
Cost of 10.00 sqm 1731.54
Cost of 1.00 sqm 173.15
Say 173.15
15.32 Demolishing thatch roofing including mats, bamboo, jaffari etc. complete
including stacking of serviceable material and disposal of unserviceable
material within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 0.54 645.00 348.30
9999 Sundries L.S. 3.64 2.12 7.72
TOTAL 356.02 W
Add 1 % Water charges on "W" 3.56
TOTAL 359.58 X
Add GST on "X" (multiplying
factor 0.1405) 50.52
TOTAL 410.10 Y
Add 15% CPOH on "Y" 61.51
TOTAL 471.61 Z
Add Cess @ 1% on "Z" 4.72
Cost of 10.00 sqm 476.33
Cost of 1.00 sqm 47.63
Say 47.65
15.33 Dismantling wooden ballies in posts and struts including stacking within
50metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 50 metre
LABOUR
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1183
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 0.52 2.12 1.10
TOTAL 646.10 W
Add 1 % Water charges on "W" 6.46
TOTAL 652.56 X
Add GST on "X" (multiplying
factor 0.1405) 91.69
TOTAL 744.25 Y
Add 15% CPOH on "Y" 111.64
TOTAL 855.89 Z
Add Cess @ 1% on "Z" 8.56
Cost of 50.00 metre 864.44
Cost of 1.00 metre 17.29
Say 17.30
15.34 Dismantling and stacking within 50 metres lead, fencing posts or struts
including all earth work and dismantling of concrete etc. in base of:
15.34.1 T' or 'L' iron or pipe
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0114 Beldar day 0.107 645.00 69.02
0115 Coolie day 0.067 645.00 43.22
9999 Excavation, transporting and stacking
the posts to the required place within
50 metres lead, refilling the pit and
dressing the same L.S. 0.26 2.12 0.55
9999 Extra for lifting of R.C.C. posts being
heavier than L iron and cleaning the
posts of stacking concrete L.S. 13.39 2.12 28.39
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 144.20 W
Add 1 % Water charges on "W" 1.44
TOTAL 145.64 X
Add GST on "X" (multiplying
factor 0.1405) 20.46
TOTAL 166.10 Y
Add 15% CPOH on "Y" 24.92
TOTAL 191.02 Z
Add Cess @ 1% on "Z" 1.91
Cost of each 192.93
Say 192.95
15.34.2 R.C.C.
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0114 Beldar day 0.097 645.00 62.57
0115 Coolie day 0.06 645.00 38.70
9999 Sundries L.S. 0.26 2.12 0.55
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1184
Code Description Unit Quantity Rate Amount
9999 Excavation, transporting and stacking
the posts to the required place within
50 metres lead, refilling the pit and
dressing the same L.S. 13.39 2.12 28.39
9999 Extra for lifting of R.C.C. posts being
heavier than L iron and cleaning the
posts of stacking concrete L.S. 8.06 2.12 17.09
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 153.08 W
Add 1 % Water charges on "W" 1.53
TOTAL 154.61 X
Add GST on "X" (multiplying
factor 0.1405) 21.72
TOTAL 176.33 Y
Add 15% CPOH on "Y" 26.45
TOTAL 202.78 Z
Add Cess @ 1% on "Z" 2.03
Cost of each 204.81
Say 204.80
15.35 Cutting ballies or wooden posts of fencing at the point of projection above
the concrete or ground and stacking the same within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 ballie (post)
9999 Cutting L.S. 2.73 2.12 5.79
9999 Transporting and stacking L.S. 1.43 2.12 3.03
TOTAL 8.82 W
Add 1 % Water charges on "W" 0.09
TOTAL 8.91 X
Add GST on "X" (multiplying
factor 0.1405) 1.25
TOTAL 10.16 Y
Add 15% CPOH on "Y" 1.52
TOTAL 11.68 Z
Add Cess @ 1% on "Z" 0.12
Cost of each 11.80
Say 11.80
15.36 Dismantling barbed wire or flexible wire rope in fencing including making rolls
and stacking within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 quintal
LABOUR
0114 Beldar day 3.50 645.00 2257.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1185
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 2268.80 W
Add 1 % Water charges on "W" 22.69
TOTAL 2291.49 X
Add GST on "X" (multiplying
factor 0.1405) 321.95
TOTAL 2613.44 Y
Add 15% CPOH on "Y" 392.02
TOTAL 3005.46 Z
Add Cess @ 1% on "Z" 30.05
Cost of 1.00 quintal 3035.51
Cost of 1.00 kg 30.36
Say 30.35
15.37 Dismantling wooden trellis work excluding frames but including stacking the
serviceable material within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 0.25 645.00 161.25
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 399.69 W
Add 1 % Water charges on “W” 4.00
TOTAL 403.68 X
Add GST on “X” (multiplying
factor 0.1405) 56.72
TOTAL 460.40 Y
Add 15% CPOH on “Y” 69.06
TOTAL 529.46 Z
Add Cess @ 1% on “Z” 5.29
Cost of 10.00 sqm 534.76
Cost of 1.00 sqm 53.48
Say 53.50
15.38 Dismantling expanded metal or I.R.C. fabrics with necessary battens and
beading including stacking the serviceable material within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.40 645.00 258.00
0115 Coolie day 0.20 645.00 129.00
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1186
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 4.16 2.12 8.82
TOTAL 467.22 W
Add 1 % Water charges on "W" 4.67
TOTAL 471.89 X
Add GST on "X" (multiplying
factor 0.1405) 66.30
TOTAL 538.19 Y
Add 15% CPOH on "Y" 80.73
TOTAL 618.92 Z
Add Cess @ 1% on "Z" 6.19
Cost of 10.00 sqm 625.11
Cost of 1.00 sqm 62.51
Say 62.50
15.39 Dismantling wooden boardings in lining of walls and partitions, excluding
supporting members but including stacking within 50 metres lead :
15.39.1 Up to 10 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.15 714.00 107.10
0114 Beldar day 0.20 645.00 129.00
0115 Coolie day 0.20 645.00 129.00
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 376.40 W
Add 1 % Water charges on "W" 3.76
TOTAL 380.16 X
Add GST on "X" (multiplying
factor 0.1405) 53.41
TOTAL 433.58 Y
Add 15% CPOH on "Y" 65.04
TOTAL 498.61 Z
Add Cess @ 1% on "Z" 4.99
Cost of 10.00 sqm 503.60
Cost of 1.00 sqm 50.36
Say 50.35
15.39.2 Thickness above 10 mm up to 25 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 0.25 645.00 161.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1187
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 479.63 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.43 X
Add GST on "X" (multiplying
factor 0.1405) 68.06
TOTAL 552.49 Y
Add 15% CPOH on "Y" 82.87
TOTAL 635.36 Z
Add Cess @ 1% on "Z" 6.35
Cost of 10.00 sqm 641.72
Cost of 1.00 sqm 64.17
Say 64.15
15.39.3 Thickness above 25 mm up to 40 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.30 645.00 193.50
0115 Coolie day 0.30 645.00 193.50
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 558.19 W
Add 1 % Water charges on "W" 5.58
TOTAL 563.77 X
Add GST on "X" (multiplying
factor 0.1405) 79.21
TOTAL 642.98 Y
Add 15% CPOH on "Y" 96.45
TOTAL 739.42 Z
Add Cess @ 1% on "Z" 7.39
Cost of 10.00 sqm 746.82
Cost of 1.00 sqm 74.68
Say 74.70
15.40 Dismantling precast concrete or stone slabs in walls, partition walls etc.
including stacking within 50 metres lead :
15.40.1 Thickness up to 40 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.20 714.00 142.80
0114 Beldar day 2.00 645.00 1290.00
0115 Coolie day 0.50 645.00 322.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1188
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.39 2.12 28.39
TOTAL 1783.69 W
Add 1 % Water charges on "W" 17.84
TOTAL 1801.52 X
Add GST on "X" (multiplying
factor 0.1405) 253.11
TOTAL 2054.64 Y
Add 15% CPOH on "Y" 308.20
TOTAL 2362.83 Z
Add Cess @ 1% on "Z" 23.63
Cost of 10.00 sqm 2386.46
Cost of 1.00 sqm 238.65
Say 238.65
15.40.2 Thickness above 40 mm up to 75 mm
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0124 Mason (brick layer) 2nd class day 0.30 714.00 214.20
0114 Beldar day 3.00 645.00 1935.00
0115 Coolie day 0.75 645.00 483.75
9999 Sundries L.S. 18.85 2.12 39.96
TOTAL 2672.91 W
Add 1 % Water charges on "W" 26.73
TOTAL 2699.64 X
Add GST on "X" (multiplying
factor 0.1405) 379.30
TOTAL 3078.94 Y
Add 15% CPOH on "Y" 461.84
TOTAL 3540.78 Z
Add Cess @ 1% on "Z" 35.41
Cost of 10.00 sqm 3576.19
Cost of 1.00 sqm 357.62
Say 357.60
15.41 Dismantling cement asbestos or other hard board ceiling or partition walls
including stacking of serviceable materials and disposal of unserviceable
materials within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm.
LABOUR
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.30 645.00 193.50
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1189
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 347.60 W
Add 1 % Water charges on "W" 3.48
TOTAL 351.08 X
Add GST on "X" (multiplying
factor 0.1405) 49.33
TOTAL 400.40 Y
Add 15% CPOH on "Y" 60.06
TOTAL 460.46 Z
Add Cess @ 1% on "Z" 4.60
Cost of 10.00 sqm. 465.07
Cost of 1.00 sqm. 46.51
Say 46.50
15.42 Dismantling C.I. or asbestos rain water pipe with fittings and clamps including
stacking the material within 50 metres lead :
15.42.1 75 to 80 mm dia pipe
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.36 645.00 232.20
9999 Sundries L.S. 0.91 2.12 1.93
TOTAL 466.33 W
Add 1 % Water charges on "W" 4.66
TOTAL 470.99 X
Add GST on "X" (multiplying
factor 0.1405) 66.17
TOTAL 537.17 Y
Add 15% CPOH on "Y" 80.58
TOTAL 617.74 Z
Add Cess @ 1% on "Z" 6.18
Cost of 10.00 metre 623.92
Cost of 1.00 metre 62.39
Say 62.40
15.42.2 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.38 645.00 245.10
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1190
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 1.56 2.12 3.31
TOTAL 480.61 W
Add 1 % Water charges on "W" 4.81
TOTAL 485.41 X
Add GST on "X" (multiplying
factor 0.1405) 68.20
TOTAL 553.61 Y
Add 15% CPOH on "Y" 83.04
TOTAL 636.66 Z
Add Cess @ 1% on "Z" 6.37
Cost of 10.00 metre 643.02
Cost of 1.00 metre 64.30
Say 64.30
15.42.3 150 mm dia pipe
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.40 645.00 258.00
9999 Sundries L.S. 2.08 2.12 4.41
TOTAL 494.61 W
Add 1 % Water charges on "W" 4.95
TOTAL 499.56 X
Add GST on "X" (multiplying
factor 0.1405) 70.19
TOTAL 569.74 Y
Add 15% CPOH on "Y" 85.46
TOTAL 655.20 Z
Add Cess @ 1% on "Z" 6.55
Cost of 10.00 metre 661.76
Cost of 1.00 metre 66.18
Say 66.20
15.43 Dismantling manually/ by mechanical means including stacking of serviceable
material and disposal of unserviceable material within 50 metres lead as per
direction of Engineer-in-charge :
15.43.1 Water bound macadam road
Code Description Unit Quantity Rate Amount
Detail of cost for 36 sqm
Consider a road 6 metres wide and 6
metres length wise 25 cm average
depth = 9.00 cubic metre
LABOUR
For cutting road taking out soiling and
metalling including sorting and screening
0114 Beldar day 4.80 645.00 3096.00
0115 Coolie day 2.40 645.00 1548.00
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1191
Code Description Unit Quantity Rate Amount
9999 Labour for stacking of serviceable
material and disposal of unserviceable
material within 50 metres lead L.S. 89.70 2.12 190.16
TOTAL 4834.16 W
Add 1 % Water charges on "W" 48.34
TOTAL 4882.51 X
Add GST on "X" (multiplying
factor 0.1405) 685.99
TOTAL 5568.50 Y
Add 15% CPOH on "Y" 835.27
TOTAL 6403.77 Z
Add Cess @ 1% on "Z" 64.04
Cost of 36.00 sqm 6467.81
Cost of 1.00 sqm 179.66
Say 179.65
15.43.2 bituminous road
Code Description Unit Quantity Rate Amount
Detail of cost for 36 sqm
Consider a road 6 metres wide and
6 metres length wise 30 cm average
depth =10.80 cubic metre
LABOUR
For cutting road taking out soiling and
metalling including sorting and screening
0114 Beldar day 9.60 645.00 6192.00
0115 Coolie day 4.80 645.00 3096.00
9999 Labour for stacking of serviceable
material and disposal of unserviceable
material within 50 metres lead L.S. 107.64 2.12 228.20
TOTAL 9516.20 W
Add 1 % Water charges on "W" 95.16
TOTAL 9611.36 X
Add GST on "X" (multiplying
factor 0.1405) 1350.40
TOTAL 10961.75 Y
Add 15% CPOH on "Y" 1644.26
TOTAL 12606.02 Z
Add Cess @ 1% on "Z" 126.06
Cost of 36.00 sqm 12732.08
Cost of 1.00 sqm 353.67
Say 353.65
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1192
15.44 Dismantling G.I. pipes (external work) including excavation and refilling
trenches after taking out the pipes, manually/ by mechanical means
including stacking of pipes within 50 metres lead as per direction of
Engineer-in-charge :
15.44.1 15 mm to 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
Trenching and refilling etc
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
9999 Dismantling G.I. pipe and stacking etc L.S. 35.88 2.12 76.07
TOTAL 927.47 W
Add 1 % Water charges on "W" 9.27
TOTAL 936.74 X
Add GST on "X" (multiplying
factor 0.1405) 131.61
TOTAL 1068.35 Y
Add 15% CPOH on "Y" 160.25
TOTAL 1228.61 Z
Add Cess @ 1% on "Z" 12.29
Cost of 10.00 metre 1240.89
Cost of 1.00 metre 124.09
Say 124.10
15.44.2 Above 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre
LABOUR
Trenching and refilling etc
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
9999 Dismantling G.I. pipe and stacking etc L.S. 71.76 2.12 152.13
TOTAL 1003.53 W
Add 1 % Water charges on "W" 10.04
TOTAL 1013.57 X
Add GST on "X" (multiplying
factor 0.1405) 142.41
TOTAL 1155.97 Y
Add 15% CPOH on "Y" 173.40
TOTAL 1329.37 Z
Add Cess @ 1% on "Z" 13.29
Cost of 10.00 metre 1342.66
Cost of 1.00 metre 134.27
Say 134.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1193
15.45 Dismantling C.I. pipes including excavation and refilling trenches after
taking out the pipes, manually/ by mechanical means breaking lead caulked
joints, melting of lead and making into blocks including stacking of pipes
& lead at site within 50 metre lead as per direction of Engineer-in-charge:
15.45.1 Up to 150 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 40.26 metre or
11 nos joints
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x0.55x0.75 m =16.61cum
Deduct for pipes of average 100 mm dia
=1x40.26x(22/7)/4x(0.118)x(0.118)
=0.44cum
Total =16.17cum
LABOUR
2.8.1 Rate as per Item No.2.8.1 of
SH: EARTH WORK cum 16.17 286.85 4638.36 A
2.25 Rate as per Item No.2.25 of
SH: EARTH WORK cum 16.17 253.95 4106.37 A
0761 Fuel wood quintal 0.46 500.00 230.00
0771 Kerosene oil litre 0.38 50.00 19.00
0117 Assistant Fitter or 2nd class Fitter day 0.63 714.00 449.82
0114 Beldar day 4.50 645.00 2902.50
9977 Carriage L.S. 53.82 2.12 114.10
TOTAL 12460.15 W
Add 1 % Water charges on "W-A" 37.15
TOTAL 12497.31 X
Add GST on "X-A" (multiplying
factor 0.1405) 527.24
TOTAL 13024.55 Y
Add 15% CPOH on "Y-A" 641.97
TOTAL 13666.52 Z
Add Cess @ 1% on "Z-A" 49.22
Cost of 40.26 metre 13715.73
Cost of 1.00 metre 340.68
Say 340.70
15.45.2 Above 150 mm dia up to 300 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for 40.26 metre or
11 nos joints
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x0.65x0.75 m =19.63cum
Deduct for pipes of average 250 mm dia
=1x40.26x(22/7)/4x(0.274)x(0.274)
=2.37cum
Total =17.26cum
LABOUR
2.8.1 Rate as per Item No.2.8.1 of
SH: EARTH WORK cum 17.26 286.85 4951.03 A
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1194
Code Description Unit Quantity Rate Amount
2.25 Rate as per Item No.2.25 of
SH: EARTH WORK cum 17.26 253.95 4383.18 A
0761 Fuel wood quintal 1.03 500.00 515.00
0771 Kerosene oil litre 1.14 50.00 57.00
0117 Assistant Fitter or 2nd class Fitter day 1.30 714.00 928.20
0114 Beldar day 7.50 645.00 4837.50
9977 Carriage L.S. 80.73 2.12 171.15
TOTAL 15843.06 W
Add 1 % Water charges on "W-A" 65.09
TOTAL 15908.14 X
Add GST on "X-A" (multiplying
factor 0.1405) 923.64
TOTAL 16831.78 Y
Add 15% CPOH on "Y-A" 1124.64
TOTAL 17956.42 Z
Add Cess @ 1% on "Z-A" 86.22
Cost of 40.26 metre 18042.64
Cost of 1.00 metre 448.15
Say 448.15
15.45.3 Above 300 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 40.26 metre or
11 nos joints
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x0.85x0.75 m =25.67cum
Deduct for pipes of average 450 mm dia
=1x40.26x(22/7)/4x(0.48)x(0.48)
=7.29cum
Total =18.38cum
LABOUR
2.8.1 Rate as per Item No.2.8.1 of
SH: EARTH WORK cum 18.38 286.85 5272.30 A
2.25 Rate as per Item No.2.25 of
SH: EARTH WORK cum 18.38 253.95 4667.60 A
0761 Fuel wood quintal 1.40 500.00 700.00
0771 Kerosene oil litre 2.27 50.00 113.50
0117 Assistant Fitter or 2nd class Fitter day 2.25 714.00 1606.50
0114 Beldar day 11.50 645.00 7417.50
9988 Carriage and sundries L.S. 134.55 2.12 285.25
TOTAL 20062.65 W
Add 1 % Water charges on "W-A" 101.23
TOTAL 20163.88 X
Add GST on "X-A" (multiplying
factor 0.1405) 1436.47
TOTAL 21600.35 Y
Add 15% CPOH on "Y-A" 1749.07
TOTAL 23349.41 Z
Add Cess @ 1% on "Z-A" 134.10
Cost of 40.26 metre 23483.51
Cost of 1.00 metre 583.30
Say 583.30
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1195
15.46 Dismantling steel cylinder R.C. pipes including excavation and refilling
trenches after taking out the pipes, manually/ by mechanical means breaking
lead caulked joints, melting of lead and making into blocks including
stacking of pipes & lead at site within 50 metres lead as per direction of
Engineer-in-charge :
15.46.1 Up to 600 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 40.26 metre or
11 nos joints
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x1.30x1.65 m =86.36cum
Deduct for pipes of average 450 mm dia
=1x40.26x(22/7)/4x(0.48)x(0.48)
=7.29cum
Total=79.07cum
LABOUR
0114 Beldar day 5.32 645.00 3431.40
0115 Coolie day 5.46 645.00 3521.70
0101 Bhisti day 0.31 714.00 221.34
0761 Fuel wood quintal 1.40 500.00 700.00
0771 Kerosene oil litre 2.27 50.00 113.50
0117 Assistant Fitter or 2nd class Fitter day 2.25 714.00 1606.50
0114 Beldar day 11.50 645.00 7417.50
9988 Carriage and sundries L.S. 134.55 2.12 285.25
TOTAL 17297.19 W
Add 1 % Water charges on "W" 172.97
TOTAL 17470.16 X
Add GST on "X" (multiplying
factor 0.1405) 2454.56
TOTAL 19924.72 Y
Add 15% CPOH on "Y" 2988.71
TOTAL 22913.42 Z
Add Cess @ 1% on "Z" 229.13
Cost of 40.26 metre 23142.56
Cost of 1.00 metre 574.83
Say 574.85
15.46.2 Above 600 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 40.26 metre or
11 nos joints
Earth work in excavation for dismantling
pipes including refilling of excavated
earth
1x40.26x1.30x1.65 m =86.36cum
Deduct for pipes of average 900 mm dia
=1x40.26x(22/7)/4x(1.00)x(1.00)
=31.63cum
Total=54.73cum
LABOUR
0114 Beldar day 15.82 645.00 10203.90
0115 Coolie day 16.25 645.00 10481.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1196
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.93 714.00 664.02
0761 Fuel wood quintal 3.08 500.00 1540.00
0771 Kerosene oil litre 5.00 50.00 250.00
0117 Assistant Fitter or 2nd class Fitter day 10.00 714.00 7140.00
0114 Beldar day 20.00 645.00 12900.00
9988 Carriage and sundries L.S. 179.40 2.12 380.33
TOTAL 43559.50 W
Add 1 % Water charges on "W" 435.59
TOTAL 43995.09 X
Add GST on "X" (multiplying
factor 0.1405) 6181.31
TOTAL 50176.40 Y
Add 15% CPOH on "Y" 7526.46
TOTAL 57702.86 Z
Add Cess @ 1% on "Z" 577.03
Cost of 40.26 metre 58279.89
Cost of 1.00 metre 1447.59
Say 1447.60
15.47 Dismantling asbestos cement pressure pipes including excavation and
refilling trenches after taking out the pipes manually/ by mechanical means
and stacking the pipes within 50 metres lead as per direction of Engineer-
in-charge :
15.47.1 Up to 150 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre or
11 nos joints
Earth work in excavation for dismantling
pipes including refilling of excavated
earth
10.00x0.55x0.75 m =4.125cum
Deduct for pipes of average 100 mm dia
=1x10x(22/7)/4x(0.118)x(0.118)
=0.109cum
Total=4.016cum
LABOUR
0114 Beldar day 1.16 645.00 748.20
0115 Coolie day 1.19 645.00 767.55
0101 Bhisti day 0.07 714.00 49.98
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.38 645.00 245.10
9988 Carriage and sundries L.S. 1.56 2.12 3.31
TOTAL 2046.34 W
Add 1 % Water charges on "W" 20.46
TOTAL 2066.80 X
Add GST on "X" (multiplying
factor 0.1405) 290.39
TOTAL 2357.19 Y
Add 15% CPOH on "Y" 353.58
TOTAL 2710.76 Z
Add Cess @ 1% on "Z" 27.11
Cost of 10.00 metre 2737.87
Cost of 1.00 metre 273.79
Say 273.80
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1197
15.47.2 Above 150 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metre or
11 nos joints
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
10.00x0.65x0.75 m =4.88cum
Deduct for pipes of average 250 mm dia
=1x10x(22/7)/4x(0.274)x(0.274)
=0.590cum
Total=4.29cum
LABOUR
0114 Beldar day 1.24 645.00 799.80
0115 Coolie day 1.28 645.00 825.60
0101 Bhisti day 0.07 714.00 49.98
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.88 645.00 567.60
9988 Carriage and sundries L.S. 3.77 2.12 7.99
TOTAL 2483.17 W
Add 1 % Water charges on "W" 24.83
TOTAL 2508.00 X
Add GST on "X" (multiplying
factor 0.1405) 352.37
TOTAL 2860.38 Y
Add 15% CPOH on "Y" 429.06
TOTAL 3289.44 Z
Add Cess @ 1% on "Z" 32.89
Cost of 10.00 metre 3322.33
Cost of 1.00 metre 332.23
Say 332.25
15.48 Taking out C.I. cover with frame from R.C.C. top slab of manholes of various
sizes including demolishing of R.C.C. work manually/ by mechanical means
and stacking of useful materials near the site and disposal of unserviceable
materials within 50 metres lead as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 man hole
Demolition of R.C.C. slab 1.3x1.2x
0.15 m =0.234cum
Less cover 0.61x0.455x0.15 m
=0.042cum
Net Quantity =0.192cum
LABOUR
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.14 645.00 90.30
9999 Removel of C.I. Cover with frame
including stacking L.S. 1.30 2.12 2.76
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1198
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 430.71 W
Add 1 % Water charges on "W" 4.31
TOTAL 435.02 X
Add GST on "X" (multiplying
factor 0.1405) 61.12
TOTAL 496.14 Y
Add 15% CPOH on "Y" 74.42
TOTAL 570.56 Z
Add Cess @ 1% on "Z" 5.71
Cost of each 576.27
Say 576.25
15.49 Taking out C.I. cover with frame from R.C.C. top slab of inspection
chambers of various sizes including demolishing of R.C.C. work manually/
by mechanical means and stacking of useful materials near the site and
disposal of unserviceable materials within 50 metres lead as per direction
of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 man hole
Demolition of R.C.C. slab
1.1x0.9x0.15 m =0.148cum
Less cover 0.61x0.455x0.15 m
=0.042cum
=0.106cum Say 0.11cum
LABOUR
0114 Beldar day 0.29 645.00 187.05
0115 Coolie day 0.08 645.00 51.60
9999 Removel of C.I. Cover with frame
including stacking L.S. 0.65 2.12 1.38
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 251.33 W
Add 1 % Water charges on "W" 2.51
TOTAL 253.84 X
Add GST on "X" (multiplying
factor 0.1405) 35.66
TOTAL 289.51 Y
Add 15% CPOH on "Y" 43.43
TOTAL 332.93 Z
Add Cess @ 1% on "Z" 3.33
Cost of each 336.26
Say 336.25
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1199
15.50 Dismantling of R.C.C. spun vent shaft including excavating the cement
concrete pit completely, taking out the shaft, refilling the excavated gap,
stacking the useful materials near the site and disposal of unserviceable
materials within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for each
Dismantling cement concrete
1:4:8 0.90x0.90x1.35m =1.094cum
Less shaft 1/4x22/7x(0.450)x(0.450)x
1.10 m =0.175cum
=0.919cum Say 0.92cum
Dismantling cement concrete
1:2:4 0.90x0.90x0.15m =0.122cum
Less shaft 1/4x22/7x0.15x0.45 m
=0.024cum
=0.098cum Say 0.10cum
LABOUR
0114 Beldar day 0.81 645.00 522.45
0115 Coolie day 0.51 645.00 328.95
9999 Sundries L.S. 1.82 2.12 3.86
0114 Beldar day 0.16 645.00 103.20
0115 Coolie day 0.07 645.00 45.15
9999 Sundries L.S. 0.52 2.12 1.10
0130 Mistry day 0.25 784.00 196.00
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0100 Bandhani day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
9999 Sundries for scaffolding etc L.S. 53.82 2.12 114.10
TOTAL 2853.57 W
Add 1 % Water charges on "W" 28.54
TOTAL 2882.10 X
Add GST on "X" (multiplying
factor 0.1405) 404.94
TOTAL 3287.04 Y
Add 15% CPOH on "Y" 493.06
TOTAL 3780.10 Z
Add Cess @ 1% on "Z" 37.80
Cost of each 3817.90
Say 3817.90
15.51 Dismantling of road gully chamber of various sizes including C.I. grating
with frame including stacking of useful materials near the site and disposal
of unserviceable materials within 50 metres lead including refilling the
excavated gap.
Code Description Unit Quantity Rate Amount
Detail of cost for one chamber
Dismantling cement concrete
a) 1:5:10 1.05x1.00x0.15m =0.16cum
Dismantling brick work in cement mortar
2.70x0.20x0.45m =0.24cum
Dismantling cement concrete
b) 1:2:4 2.70x0.20x0.15m =0.08cum
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1200
Code Description Unit Quantity Rate Amount
LABOUR
0114 Beldar day 0.14 645.00 90.30
0115 Coolie day 0.09 645.00 58.05
9999 Sundries L.S. 0.26 2.12 0.55
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 0.22 645.00 141.90
9999 Sundries L.S. 0.52 2.12 1.10
0114 Beldar day 0.13 645.00 83.85
0115 Coolie day 0.06 645.00 38.70
9999 Sundries for scaffolding etc L.S. 0.39 2.12 0.83
9999 Dismantling C.I. Grating L.S. 7.15 2.12 15.16
TOTAL 591.69 W
Add 1 % Water charges on "W" 5.92
TOTAL 597.61 X
Add GST on "X" (multiplying
factor 0.1405) 83.96
TOTAL 681.57 Y
Add 15% CPOH on "Y" 102.24
TOTAL 783.80 Z
Add Cess @ 1% on "Z" 7.84
Cost of each 791.64
Say 791.65
15.52 Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)
including stacking of useful materials near the site and disposal of
unserviceable materials within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for each
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 17.94 2.12 38.03
TOTAL 556.53 W
Add 1 % Water charges on "W" 5.57
TOTAL 562.10 X
Add GST on "X" (multiplying
factor 0.1405) 78.97
TOTAL 641.07 Y
Add 15% CPOH on "Y" 96.16
TOTAL 737.23 Z
Add Cess @ 1% on "Z" 7.37
Cost of each 744.61
Say 744.60
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1201
15.53 Dismantling of C.I. sluice valve including stacking of useful materials within
a lead of 50 metres
15.53.1 Up to 150 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for dismantling 10 sluice
valves (ave.) 100mm
LABOUR
0116 Fitter (grade 1) day 0.60 784.00 470.40
0117 Assistant Fitter or 2nd class Fitter day 0.40 714.00 285.60
0114 Beldar day 1.60 645.00 1032.00
9999 Sundries for removing the R.C.C. cover
etc for dismantling sluice valve L.S. 89.70 2.12 190.16
TOTAL 1978.16 W
Add 1 % Water charges on "W" 19.78
TOTAL 1997.95 X
Add GST on "X" (multiplying
factor 0.1405) 280.71
TOTAL 2278.66 Y
Add 15% CPOH on "Y" 341.80
TOTAL 2620.46 Z
Add Cess @ 1% on "Z" 26.20
Cost of 10 Nos 2646.66
Cost of each 264.67
Say 264.65
15.53.2 Above 150 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for dismantling 10 sluice
valves (ave.) 250mm
LABOUR
0116 Fitter (grade 1) day 2.40 784.00 1881.60
0117 Assistant Fitter or 2nd class Fitter day 1.54 714.00 1099.56
0114 Beldar day 6.40 645.00 4128.00
9999 Sundries for removing the R.C.C.
cover etc for dismantling sluice valve L.S. 89.70 2.12 190.16
TOTAL 7299.32 W
Add 1 % Water charges on "W" 72.99
TOTAL 7372.32 X
Add GST on "X" (multiplying
factor 0.1405) 1035.81
TOTAL 8408.13 Y
Add 15% CPOH on "Y" 1261.22
TOTAL 9669.35 Z
Add Cess @ 1% on "Z" 96.69
Cost of 10 Nos 9766.04
Cost of each 976.60
Say 976.60
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1202
15.54 Dismantling of spindle fire hydrant including stacking of useful materials
within 50 metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 Nos
LABOUR
0116 Fitter (grade 1) day 1.50 784.00 1176.00
0117 Assistant Fitter or 2nd class Fitter day 1.00 714.00 714.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 4470.00 W
Add 1 % Water charges on "W" 44.70
TOTAL 4514.70 X
Add GST on "X" (multiplying
factor 0.1405) 634.32
TOTAL 5149.02 Y
Add 15% CPOH on "Y" 772.35
TOTAL 5921.37 Z
Add Cess @ 1% on "Z" 59.21
Cost of 10 Nos 5980.58
Cost of each 598.06
Say 598.05
15.55 Dismantling of cement concrete platform along with curtain walls and base
concrete etc. including stacking of useful materials near the site and
disposal of unserviceable materials within 50 metres lead :
15.55.1 120 x 120 cm (outside to outside)
Code Description Unit Quantity Rate Amount
Detail of cost for one platform
Dismantling cement concrete 1:5:10
4.00x0.35x0.12m =0.168cum
0.80x0.80x0.075m =0.048cum
=0.216cum Say 0.22cum
Dismantling brick work in cement mortar
4.00x0.20x0.30m =0.24cum
4.00x0.10x0.20m =0.088cum
=0.328cum Say 0.33cum
Dismantling 40 mm C.C. flooring 1:2:4
1.00x1.00x0.04m =0.04cum
LABOUR
0114 Beldar day 0.19 645.00 122.55
0115 Coolie day 0.12 645.00 77.40
9999 Sundries L.S. 0.39 2.12 0.83
0114 Beldar day 0.35 645.00 225.75
0115 Coolie day 0.30 645.00 193.50
9999 Sundries L.S. 0.91 2.12 1.93
0114 Beldar day 0.06 645.00 38.70
0115 Coolie day 0.03 645.00 19.35
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1203
Code Description Unit Quantity Rate Amount
9999 Sundries for scaffolding etc L.S. 0.13 2.12 0.28
TOTAL 680.28 W
Add 1 % Water charges on "W" 6.80
TOTAL 687.08 X
Add GST on "X" (multiplying
factor 0.1405) 96.54
TOTAL 783.62 Y
Add 15% CPOH on "Y" 117.54
TOTAL 901.16 Z
Add Cess @ 1% on "Z" 9.01
Cost of each 910.17
Say 910.15
15.55.2 210 x 120 cm (outside to outside)
Code Description Unit Quantity Rate Amount
Detail of cost for one platform
Dismantling cement concrete 1:5:10
5.80x0.35x0.12m =0.243cum
0.80x1.70x0.075m =0.102cum
=0.345cum Say 0.35cum
Dismantling brick work in cement mortar
5.80x0.20x0.30m =0.348cum
6.20x0.10x0.20m =0.124cum
=0.472cum Say 0.47cum
Dismantling 40 mm C.C. flooring 1:2:4
1.90x1.00x0.04m =0.08cum
LABOUR
0114 Beldar day 0.31 645.00 199.95
0115 Coolie day 0.19 645.00 122.55
9999 Sundries L.S. 0.65 2.12 1.38
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.42 645.00 270.90
9999 Sundries L.S. 1.30 2.12 2.76
0114 Beldar day 0.13 645.00 83.85
0115 Coolie day 0.06 645.00 38.70
9999 Sundries for scaffolding etc L.S. 0.39 2.12 0.83
TOTAL 1043.41 W
Add 1 % Water charges on "W" 10.43
TOTAL 1053.84 X
Add GST on "X" (multiplying
factor 0.1405) 148.07
TOTAL 1201.91 Y
Add 15% CPOH on "Y" 180.29
TOTAL 1382.20 Z
Add Cess @ 1% on "Z" 13.82
Cost of each 1396.02
Say 1396.00
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1204
15.55.3 320 x 120 cm (outside to outside)
Code Description Unit Quantity Rate Amount
Detail of cost for one platform
Dismantling cement concrete 1:5:10
8.00x0.35x0.12m =0.336cum
2.80x0.80x0.075m =0.168cum
=0.504cum Say 0.50cum
Dismantling brick work in cement mortar
8.00x0.20x0.30m =0.48cum
8.40x0.10x0.20m =0.168cum
=0.648cum Say 0.65cum
Dismantling 40 mm C.C. flooring 1:2:4
3.00x1.00x0.04m =0.12cum
LABOUR
0114 Beldar day 0.44 645.00 283.80
0115 Coolie day 0.28 645.00 180.60
9999 Sundries L.S. 0.91 2.12 1.93
0114 Beldar day 0.69 645.00 445.05
0115 Coolie day 0.59 645.00 380.55
9999 Sundries L.S. 1.56 2.12 3.31
0114 Beldar day 0.19 645.00 122.55
0115 Coolie day 0.09 645.00 58.05
9999 Sundries for scaffolding etc L.S. 0.52 2.12 1.10
TOTAL 1476.94 W
Add 1 % Water charges on "W" 14.77
TOTAL 1491.71 X
Add GST on "X" (multiplying
factor 0.1405) 209.59
TOTAL 1701.29 Y
Add 15% CPOH on "Y" 255.19
TOTAL 1956.49 Z
Add Cess @ 1% on "Z" 19.56
Cost of each 1976.05
Say 1976.05
15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface
for plaster including disposal of rubbish to the dumping ground within 50
metres lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 0.36 645.00 232.20
0115 Coolie day 0.08 645.00 51.60
0101 Bhisti day 0.07 714.00 49.98
9999 Sundries for scaffolding etc L.S. 1.43 2.12 3.03
TOTAL 336.81 W
Add 1 % Water charges on "W" 3.37
TOTAL 340.18 X
Add GST on "X" (multiplying
factor 0.1405) 47.80
TOTAL 387.97 Y
Add 15% CPOH on "Y" 58.20
TOTAL 446.17 Z
Add Cess @ 1% on "Z" 4.46
Cost of 10.00 sqm 450.63
Cost of 1.00 sqm 45.06
Say 45.05
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1205
15.57 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing
and false ceiling including disposal of unserviceable material and stacking
of serviceable material with in 50 meters lead as directed by Engineer-in-
charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 5.38 2.12 11.41
TOTAL 347.71 W
Add 1 % Water charges on "W" 3.48
TOTAL 351.18 X
Add GST on "X" (multiplying
factor 0.1405) 49.34
TOTAL 400.52 Y
Add 15% CPOH on "Y" 60.08
TOTAL 460.60 Z
Add Cess @ 1% on "Z" 4.61
Cost of 10.00 sqm 465.21
Cost of 1.00 sqm 46.52
Say 46.50
15.58 Demolishing R.C.C. work by mechanical means and stockpiling at
designated locations and disposal of dismantled materials up to a lead of 1
kilometre, stacking serviceable and unserviceable material separately
including cutting reinforcement bars.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
LABOUR
0128 Mate day 0.03 714.00 21.42
Labour for operating pneumatic tools
0139 Skilled Beldar (for floor rubbing etc.) day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
Labour for cutting reinforcement bars.
0103 Blacksmith 2nd class day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
MACHINERY
0040 Air compressor 250 cfm with two leads
for pneumatic cutters/ hammers. day 0.125 1600.00 200.00
0039 Tractor with trolley . day 0.05 1200.00 60.00
0041 Joint cutting machine with 2-3 blades day 0.125 800.00 100.00
TOTAL 1740.42 W
Add 1 % Water charges on “W” 17.40
TOTAL 1757.82 X
Add GST on “X” (multiplying
factor 0.1405) 246.97
TOTAL 2004.80 Y
Add 15% CPOH on “Y” 300.72
TOTAL 2305.52 Z
Add Cess @ 1% on “Z” 23.06
Cost of 1 cum 2328.57
Say 2328.55
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1206
15.59 Dismantling of flexible pavement (bituminous courses) by mechanical
means and disposal of dismantled material up to a lead of 1 kilometre, as
per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
LABOUR
0128 Mate day 0.01 714.00 7.14
0114 Beldar day 0.30 645.00 193.50
MACHINERY
0039 Tractor with trolley . day 0.0475 1200.00 57.00
0038 Tractor with ripper attachment. day 0.002 1200.00 2.40
TOTAL 260.04 W
Add 1 % Water charges on "W" 2.60
TOTAL 262.64 X
Add GST on "X" (multiplying
factor 0.1405) 36.90
TOTAL 299.54 Y
Add 15% CPOH on "Y" 44.93
TOTAL 344.47 Z
Add Cess @ 1% on "Z" 3.44
Cost of 1 cum 347.92
Say 347.90
15.60 Disposal of building rubbish / malba / similar unserviceable, dismantled or
waste materials by mechanical means, including loading, transporting,
unloading to approved municipal dumping ground or as approved by
Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts
involved.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
2264 Carriage of Rubbish cum 1.00 163.93 163.93
TOTAL 163.93 W
Add 1 % Water charges on “W” 1.64
TOTAL 165.57 X
Add GST on “X” (multiplying
factor 0.1405) 23.26
TOTAL 188.83 Y
Add 15% CPOH on “Y” 28.32
TOTAL 217.16 Z
Add Cess @ 1% on “Z” 2.17
Cost of 1 cum 219.33
Say 219.35
SUB HEAD : 15- DISMANTLING AND DEMOLISHING 1207
SUB HEAD : 16.0
ROAD WORK
1209
16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12
tonne capacity after excavating earth to an average of 22.5 cm depth, dressing
to camber and consolidating with road roller including making good the
undulations etc. and re-rolling the sub grade and disposal of surplus earthwith
lead upto 50 metres.
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
(A) preparation of subgrade.
Earth work in excavation including
dressing etc. 100sqm.x22.5cm
(average depth) = 22.5cum.
LABOUR
0128 Mate day 1.80 714.00 1285.20
0115 Coolie day 18.00 645.00 11610.00
0114 Beldar day 0.27 645.00 174.15
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.054 3000.00 162.00
0113 Chowkidar day 0.054 645.00 34.83
9999 Sundries L.S. 6.76 2.12 14.33
(B) Conslidation of subgrade
Roller charges (one roller does 1860
sqm. of conosolidation of sub - grade
with road roller of 8 to 12 tonne
capacity including making good the
undulations etc. with earth or quarry
spoils etc. and rerolling the subgrade
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.054 3000.00 162.00
0113 Chowkidar day 0.054 645.00 34.83
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 13491.67 W
Add 1 % Water charges on “W” 134.92
TOTAL 13626.59 X
Add GST on “X” (multiplying
factor 0.1405) 1914.54
TOTAL 15541.12 Y
Add 15% CPOH on “Y” 2331.17
TOTAL 17872.29 Z
Add Cess @ 1% on “Z” 178.72
Cost for 100 sqm. 18051.02
Cost per sqm. 180.51
Say 180.50
16.2 Extra for compaction of earth work in embankment under optimum moisture
conditions to give at least 95% of the maximum dry density (proctor density).
Code Description Unit Quantity Rate Amount
LABOUR
(Extra to item No.2.3 in Earth work)
0101 Bhisti day 0.17 714.00 121.38
Roller charges (one roller does
1860 sqm. Of consolidation per day of
8 hours and uses 18 litres diesel)
SUB HEAD : 16- ROAD WORK 1211
Code Description Unit Quantity Rate Amount
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.008 3000.00 24.00
0113 Chowkidar day 0.008 645.00 5.16
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 153.57 W
Add 1 % Water charges on "W" 1.54
TOTAL 155.11 X
Add GST on "X" (multiplying
factor 0.1405) 21.79
TOTAL 176.90 Y
Add 15% CPOH on "Y" 26.53
TOTAL 203.43 Z
Add Cess @ 1% on "Z" 2.03
Cost of 10 cum. 205.47
Cost per cum. 20.55
Say 20.55
16.3 Supplying and stacking at site.
16.3.1 90 mm to 45 mm size stone aggregate
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2901 Stone Aggregate (Single size) :
100 mm nominal size cum 0.10 1360.00 136.00
2902 Stone Aggregate (Single size) :
80 mm nominal size cum 0.65 1360.00 884.00
0291 Stone Aggregate (Single size) :
63 mm nominal size cum 0.25 1000.00 250.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 1.00 178.19 178.19
TOTAL 1448.19 W
Add 1 % Water charges on "W" 14.48
TOTAL 1462.67 X
Add GST on "X" (multiplying
factor 0.1405) 205.51
TOTAL 1668.18 Y
Add 15% CPOH on "Y" 250.23
TOTAL 1918.40 Z
Add Cess @ 1% on "Z" 19.18
Cost for 1 cum 1937.59
Say 1937.60
16.3.2 63 mm to 45 mm size stone aggregate
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2902 Stone Aggregate (Single size) :
80 mm nominal size cum 0.10 1360.00 136.00
0291 Stone Aggregate (Single size) :
63 mm nominal size cum 0.65 1000.00 650.00
SUB HEAD : 16- ROAD WORK 1212
Code Description Unit Quantity Rate Amount
0292 Stone Aggregate (Single size) :
50 mm nominal size cum 0.25 1000.00 250.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 1.00 178.19 178.19
TOTAL 1214.19 W
Add 1 % Water charges on "W" 12.14
TOTAL 1226.33 X
Add GST on "X" (multiplying
factor 0.1405) 172.30
TOTAL 1398.63 Y
Add 15% CPOH on "Y" 209.79
TOTAL 1608.43 Z
Add Cess @ 1% on "Z" 16.08
Cost for 1 cum 1624.51
Say 1624.50
16.3.3 53 mm to 22.4 mm size stone aggregate
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
0291 Stone Aggregate (Single size) :
63 mm nominal size cum 0.05 1000.00 50.00
0292 Stone Aggregate (Single size) :
50 mm nominal size cum 0.30 1000.00 300.00
0293 Stone Aggregate (Single size) :
40 mm nominal size cum 0.65 1300.00 845.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 1.00 178.19 178.19
TOTAL 1373.19 W
Add 1 % Water charges on "W" 13.73
TOTAL 1386.92 X
Add GST on "X" (multiplying
factor 0.1405) 194.86
TOTAL 1581.78 Y
Add 15% CPOH on "Y" 237.27
TOTAL 1819.05 Z
Add Cess @ 1% on "Z" 18.19
Cost for 1 cum 1837.24
Say 1837.25
16.3.4 Over burnt (Jhama) brick aggregate 120 mm to 40 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2908 Over burnt (Jhama) Brick Aggregate:
120 mm to 40 mm size cum 1.00 550.00 550.00
SUB HEAD : 16- ROAD WORK 1213
Code Description Unit Quantity Rate Amount
2260 Carriage of Brick aggregate cum 1.00 178.19 178.19
TOTAL 728.19 W
Add 1 % Water charges on "W" 7.28
TOTAL 735.47 X
Add GST on "X" (multiplying
factor 0.1405) 103.33
TOTAL 838.81 Y
Add 15% CPOH on "Y" 125.82
TOTAL 964.63 Z
Add Cess @ 1% on "Z" 9.65
Cost for 1 cum 974.27
Say 974.25
16.3.5 Over burnt (Jhama) brick aggregate 90 mm to 45 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2909 Over burnt (Jhama) Brick Aggregate:
90 mm to 40 mm size cum 1.00 600.00 600.00
2260 Carriage of Brick aggregate cum 1.00 178.19 178.19
TOTAL 778.19 W
Add 1 % Water charges on "W" 7.78
TOTAL 785.97 X
Add GST on "X" (multiplying
factor 0.1405) 110.43
TOTAL 896.40 Y
Add 15% CPOH on "Y" 134.46
TOTAL 1030.86 Z
Add Cess @ 1% on "Z" 10.31
Cost for 1 cum 1041.17
Say 1041.15
16.3.6 Stone screening 13.2 mm nominal size (Type A)
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2910 Stone chippings/ screenings
12.5/13.2 mm nominal size cum 0.05 1200.00 60.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.80 1200.00 960.00
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 0.15 1400.00 210.00
SUB HEAD : 16- ROAD WORK 1214
Code Description Unit Quantity Rate Amount
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.00 163.93 163.93
TOTAL 1393.93 W
Add 1 % Water charges on "W" 13.94
TOTAL 1407.87 X
Add GST on "X" (multiplying
factor 0.1405) 197.81
TOTAL 1605.67 Y
Add 15% CPOH on "Y" 240.85
TOTAL 1846.53 Z
Add Cess @ 1% on "Z" 18.47
Cost for one cum. 1864.99
Say 1865.00
16.3.7 Stone screening 11.2 mm nominal size (Type B)
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.10 1200.00 120.00
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 0.75 1400.00 1050.00
2904 Stone chippings/ screenings
150 micron nominal size cum 0.15 1400.00 210.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.85 163.93 139.34
2267 Carriage of Stone dust cum 0.15 163.93 24.59
TOTAL 1543.93 W
Add 1 % Water charges on "W" 15.44
TOTAL 1559.37 X
Add GST on "X" (multiplying
factor 0.1405) 219.09
TOTAL 1778.46 Y
Add 15% CPOH on "Y" 266.77
TOTAL 2045.23 Z
Add Cess @ 1% on "Z" 20.45
Cost for one cum. 2065.68
Say 2065.70
16.3.8 Red bajri
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
0304 Bajri cum 1.00 1000.00 1000.00
SUB HEAD : 16- ROAD WORK 1215
Code Description Unit Quantity Rate Amount
2311 Carriage of Red bajri cum 1.00 163.93 163.93
TOTAL 1163.93 W
Add 1 % Water charges on "W" 11.64
TOTAL 1175.57 X
Add GST on "X" (multiplying
factor 0.1405) 165.17
TOTAL 1340.74 Y
Add 15% CPOH on "Y" 201.11
TOTAL 1541.85 Z
Add Cess @ 1% on "Z" 15.42
Cost for one cum. 1557.27
Say 1557.25
16.3.9 Good earth
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
Excavation :
LABOUR
0114 Beldar day 0.177 645.00 114.17
0115 Coolie day 0.167 645.00 107.72
0979 Royalty for good earth cum 1.00 40.00 40.00
2241 Carriage of Good earth cum 1.00 204.92 204.92
by mechanical transport upto 5 km lead
TOTAL 466.80 W
Add 1 % Water charges on "W" 4.67
TOTAL 471.47 X
Add GST on "X" (multiplying
factor 0.1405) 66.24
TOTAL 537.71 Y
Add 15% CPOH on "Y" 80.66
TOTAL 618.37 Z
Add Cess @ 1% on "Z" 6.18
Cost per cum. 624.55
Say 624.55
16.3.10 Moorum
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
0810 Moorum cum 1.00 500.00 500.00
2265 Carriage of Moorum cum 1.00 163.93 163.93
TOTAL 663.93 W
Add 1 % Water charges on "W" 6.64
TOTAL 670.57 X
Add GST on "X" (multiplying
factor 0.1405) 94.21
TOTAL 764.78 Y
Add 15% CPOH on "Y" 114.72
TOTAL 879.50 Z
Add Cess @ 1% on "Z" 8.80
Cost for one cum. 888.30
Say 888.30
SUB HEAD : 16- ROAD WORK 1216
16.4 Laying, spreading and compacting stone aggregate of specified sizes to WBM
specifications in uniform thickness, hand picking, rolling with 3 wheeled road/
vibratory roller 8-10 tonne capacity in stages to proper grade and camber,
applying and brooming requisite type of screening / binding material to fill up
interstices of coarse aggregate, watering and compacting to the required
density .
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
LABOUR
0114 Beldar day 0.26 645.00 167.70
0115 Coolie day 0.26 645.00 167.70
0101 Bhisti day 0.26 714.00 185.64
Roller charges (one roller does 30 cum
consolidation per day of 8 hours and
uses 18 litres of diesel oil).
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.033 3000.00 99.00
0113 Chowkidar day 0.033 645.00 21.29
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 647.11 W
Add 1 % Water charges on "W" 6.47
TOTAL 653.58 X
Add GST on "X" (multiplying
factor 0.1405) 91.83
TOTAL 745.41 Y
Add 15% CPOH on "Y" 111.81
TOTAL 857.22 Z
Add Cess @ 1% on "Z" 8.57
Cost for 1 cum 865.80
Say 865.80
16.5 Laying water bound macadam sub-base with brick aggregate and binding
material, earth etc. including screening, sorting and spreading to template
and consolidation with light power road-roller etc. complete.(payment for brick
aggregate and moorum etc. to be made separately)
16.5.1 Over burnt (Jhama) brick aggregate 120 mm to 40 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
LABOUR
0114 Beldar day 0.35 645.00 225.75
0115 Coolie day 0.26 645.00 167.70
0101 Bhisti Day 0.18 714.00 128.52
Roller charges (one roller does 230cum.
consolidation per day of 8 hours and
uses 18 litres of diesel oil)
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.004 3000.00 12.00
0113 Chowkidar day 0.004 645.00 2.58
SUB HEAD : 16- ROAD WORK 1217
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 542.34 W
Add 1 % Water charges on "W" 5.42
TOTAL 547.76 X
Add GST on "X" (multiplying
factor 0.1405) 76.96
TOTAL 624.72 Y
Add 15% CPOH on "Y" 93.71
TOTAL 718.43 Z
Add Cess @ 1% on "Z" 7.18
Cost for one cum. 725.61
Say 725.60
16.5.2 Over burnt (Jhama) brick aggregate 90 mm to 45 mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
LABOUR
0114 Beldar day 0.35 645.00 225.75
0115 Coolie day 0.26 645.00 167.70
0101 Bhisti day 0.18 714.00 128.52
Roller charges (one roller does 230cum.
consolidation per day of 8 hours and
uses 18 litres of diesel oil)
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.004 3000.00 12.00
0113 Chowkidar day 0.004 645.00 2.58
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 542.34 W
Add 1 % Water charges on "W" 5.42
TOTAL 547.76 X
Add GST on "X" (multiplying
factor 0.1405) 76.96
TOTAL 624.72 Y
Add 15% CPOH on "Y" 93.71
TOTAL 718.43 Z
Add Cess @ 1% on "Z" 7.18
Cost for one cum. 725.61
Say 725.60
16.6 Supplying, stacking and Spreading 6 mm thick red bajri, watering and rolling
complete including preparation of the surface and rolling.
16.6.1 With road roller/ hand roller
Code Description Unit Quantity Rate Amount
Details of cost for 6 mm thick and
100 sqm area
(A) Supplying and stacking of Red bajri
at site.
MATERIAL
0304 Bajri cum 0.60 1000.00 600.00
2311 Carriage of Red bajri cum 0.60 163.93 98.36
SUB HEAD : 16- ROAD WORK 1218
Code Description Unit Quantity Rate Amount
(B) Spreading of red bajri
LABOUR
0114 Beldar day 0.54 645.00 348.30
0101 Bhisti day 0.54 714.00 385.56
Roller charges (one roller does 1860sqm.
consolidation per day of 8 hours and
uses 18 litres of diesel oil)
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.054 3000.00 162.00
0113 Chowkidar day 0.054 645.00 34.83
TOTAL 1629.05 W
Add 1 % Water charges on "W" 16.29
TOTAL 1645.34 X
Add GST on "X" (multiplying
factor 0.1405) 231.17
TOTAL 1876.51 Y
Add 15% CPOH on "Y" 281.48
TOTAL 2157.98 Z
Add Cess @ 1% on "Z" 21.58
Cost for 100 sqm. 2179.56
Cost per sqm. 21.80
Say 21.80
16.7 Brick edging in full brick width and half brick depth including excavation,
refilling and disposal of surplus earth lead upto 50 metres.
16.7.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
2602 Common burnt clay F.P.S. (non
modular) bricks class designation 7.5 1000 Nos 0.16 4590.00 734.40
including 12% wastage
2201 Carriage of Bricks 1000 Nos 0.16 437.15 69.94
LABOUR
0123 Mason (brick layer) 1st class day 0.17 784.00 133.28
0124 Mason (brick layer) 2nd class day 0.17 714.00 121.38
0115 Coolie day 0.35 645.00 225.75
9999 Removal of rubbish L.S. 17.94 2.12 38.03
9999 Sundries L.S. 8.97 2.12 19.02
TOTAL 1341.80 W
Add 1 % Water charges on "W" 13.42
TOTAL 1355.22 X
Add GST on "X" (multiplying
factor 0.1405) 190.41
TOTAL 1545.63 Y
Add 15% CPOH on "Y" 231.84
TOTAL 1777.47 Z
Add Cess @ 1% on "Z" 17.77
Cost for 10 metres 1795.25
Cost per metre 179.52
Say 179.50
SUB HEAD : 16- ROAD WORK 1219
16.8 Brick edging laid lengthwise with half brick depth including excavation, refilling
and disposal of surplus earth lead upto 50 metres :
16.8.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
2602 Common burnt clay F.P.S. (non
modular) bricks class designation 7.5 1000 Nos 0.049 4590.00 224.91
including 12% wastage
2201 Carriage of Bricks 1000 Nos 0.049 437.15 21.42
LABOUR
0123 Mason (brick layer) 1st class day 0.04 784.00 31.36
0124 Mason (brick layer) 2nd class day 0.04 714.00 28.56
0115 Coolie day 0.09 645.00 58.05
9999 Removal of rubbish L.S. 4.16 2.12 8.82
TOTAL 373.12 W
Add 1 % Water charges on "W" 3.73
TOTAL 376.85 X
Add GST on "X" (multiplying
factor 0.1405) 52.95
TOTAL 429.80 Y
Add 15% CPOH on "Y" 64.47
TOTAL 494.27 Z
Add Cess @ 1% on "Z" 4.94
Cost for 10 metre 499.21
Cost per metre 49.92
Say 49.90
16.9 Scarifying metalled (water-bound) road surface including disposal of rubbish,
lead upto 50 m and consolidation of the aggregate received from scarifying
with power road roller of 8 to 10 tonne capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
LABOUR
0114 Beldar day 1.35 645.00 870.75
0115 Coolie day 1.08 645.00 696.60
Consolidation of scarified material
100sqm.x50mm = 5cum +
Less 20% wastage = 1 cum.
= 4 cum.
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.132 3000.00 396.00
0113 Chowkidar day 0.132 645.00 85.14
9999 Sundries L.S. 5.46 2.12 11.58
TOTAL 2060.07 W
Add 1 % Water charges on "W" 20.60
TOTAL 2080.67 X
Add GST on "X" (multiplying
factor 0.1405) 292.33
TOTAL 2373.00 Y
Add 15% CPOH on "Y" 355.95
TOTAL 2728.95 Z
Add Cess @ 1% on "Z" 27.29
Cost for 100 sqm. 2756.24
Cost per sqm. 27.56
Say 27.55
SUB HEAD : 16- ROAD WORK 1220
16.10 Making bajri path including preparation of subgrade, supplying and laying
brick aggregate of 50 mm nominal size 7.5 cm deep with blinding material
consisting of 12 mm moorum and 12 mm red bajri consolidated with road
roller.
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
Earth work in excavation including
dressing etc.
100x0.075=7.5cum.
2.6.1 (Rate as per item no.2.6.1 of
S.H. Earth work) cum 7.50 205.45 1540.88 A
Collection and stacking of brick
aggregate 53mm nominal size
100x0.075 =7.50cum.
0286 Brick Aggregate (Single size) : 50 mm
nominal size cum 7.50 650.00 4875.00
2260 Carriage of Brick aggregate cum 7.50 178.19 1336.43
Supply staking Red Bajri
100x0.012= 1.2 cum
16.3.8 Rate as per Item Number 16.3.8 of
SH: Road Work cum 1.20 1557.25 1868.70 A
Collection and stacking of moorum at site
100x0.012 = 1.20cum.
16.3.10 Rate as per Item Number 16.3.10 of
SH: Road Work cum 1.20 888.30 1065.96 A
Spreading and consolidation of brick
aggregate and blinding material etc.
LABOUR
0114 Beldar day 1.95 645.00 1257.75
0115 Coolie day 2.63 645.00 1696.35
0101 Bhisti day 1.35 714.00 963.90
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.135 3000.00 405.00
0113 Chowkidar day 0.135 645.00 87.08
9999 Sundries L.S. 20.15 2.12 42.72
Spreading of red bajri, watering and
rolling
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.054 3000.00 162.00
0113 Chowkidar day 0.054 645.00 34.83
TOTAL 15336.58 W
Add 1 % Water charges on "W-A" 108.61
TOTAL 15445.19 X
Add GST on "X-A" (multiplying
factor 0.1405) 1541.24
TOTAL 16986.43 Y
Add 15% CPOH on "Y-A" 1876.63
TOTAL 18863.06 Z
Add Cess @ 1% on "Z-A" 143.88
Cost for 100 sqm. 19006.94
Cost per sqm. 190.07
Say 190.05
SUB HEAD : 16- ROAD WORK 1221
16.11 Dry stone pitching 22.5 cm thick including supply of stones and preparing
surface complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
1158 Stone for pitching 15 cm x 22.5 cm cum 2.25 600.00 1350.00
2216 Carriage of Stone blocks white &
red sand stone & kota stone slab tonne 5.05 145.72 735.89
2.25x2245/1000 = 5.05 t
LABOUR
0123 Mason (brick layer) 1st class day 1.08 784.00 846.72
0124 Mason (brick layer) 2nd class day 1.08 714.00 771.12
0114 Beldar day 2.15 645.00 1386.75
0115 Coolie day 1.61 645.00 1038.45
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 6143.26 W
Add 1 % Water charges on "W" 61.43
TOTAL 6204.69 X
Add GST on "X" (multiplying
factor 0.1405) 871.76
TOTAL 7076.45 Y
Add 15% CPOH on "Y" 1061.47
TOTAL 8137.92 Z
Add Cess @ 1% on "Z" 81.38
Cost for 10 sqm. 8219.30
Cost per sqm. 821.93
Say 821.95
16.12 Dry brick pitching half brick thick in drains including supply of bricks and
preparing the surface complete :
16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
2602 Common burnt clay F.P.S. (non
modular) bricks class designation 7.5 1000 Nos 0.645 4590.00 2960.55
2201 Carriage of Bricks 1000 Nos 0.645 437.15 281.96
LABOUR
0123 Mason (brick layer) 1st class day 0.40 784.00 313.60
0124 Mason (brick layer) 2nd class day 0.40 714.00 285.60
0114 Beldar day 1.08 645.00 696.60
TOTAL 4538.31 W
Add 1 % Water charges on "W" 45.38
TOTAL 4583.69 X
Add GST on "X" (multiplying
factor 0.1405) 644.01
TOTAL 5227.70 Y
Add 15% CPOH on "Y" 784.16
TOTAL 6011.86 Z
Add Cess @ 1% on "Z" 60.12
Cost for 10 sqm. 6071.98
Cost per sqm. 607.20
Say 607.20
SUB HEAD : 16- ROAD WORK 1222
16.13 Cutting road and making good the same including supply of extra quantities
of materials i.e. aggregate, moorum screening, red bajri and labour required.
16.13.1 bituminous portion
Code Description Unit Quantity Rate Amount
Details of cost for 1.08cum. (road 6
metres wide, 0.6 metre length wise and
0.30m (average depth) volume = 1.08
cum).
MATERIAL
Supplying and stacking stone aggregate
53mm to 24 mm nominal size at site.
16.3.3 Rate as per Item Number 16.3.3 of
SH: Road Work cum 0.09 1837.25 165.35 A
Supplying and stacking red bajri at site
16.3.8 Rate as per Item Number 16.3.8 of
SH: Road Work cum 0.023 1557.25 35.82 A
Supplying and stacking moorum at site
16.3.10 Rate as per Item Number 16.3.10 of
SH: Road Work cum 0.022 888.30 19.54 A
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.092 1200.00 110.40
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.092 163.93 15.08
0309 Paving bitumen VG-10 of approved
quality tonne 0.011 25614.00 281.75
2211 Carriage of Tar bitumen tonne 0.011 163.93 1.80
LABOUR
For cutting road and taking out soling
and metalling including sorting and
screening.
0114 Beldar day 0.96 645.00 619.20
0115 Coolie day 0.48 645.00 309.60
Relaying soling stone 3.6x0.15
=0.54cum.
0114 Beldar day 0.24 645.00 154.80
0115 Coolie day 0.24 645.00 154.80
Relaying road metal with extra quantity
and consolidation to 0.10m, thickness
3.6x0.10=0.36cum.
0114 Beldar day 0.71 645.00 457.95
0115 Coolie day 0.48 645.00 309.60
0101 Bhisti day 0.10 714.00 71.40
Painting two coats, 3.6sqm. including
labour for spreading grit
0114 Beldar day 0.48 645.00 309.60
0115 Coolie day 0.48 645.00 309.60
9999 Barrier, chowkidar, sprayman, mate, etc. L.S. 40.43 2.12 85.71
TOTAL 3412.01 W
Add 1 % Water charges on “W-A” 31.91
TOTAL 3443.93 X
Add GST on “X-A” (multiplying
factor 0.1405) 452.86
TOTAL 3896.79 Y
Add 15% CPOH on “Y-A” 551.41
TOTAL 4448.20 Z
Add Cess @ 1% on “Z-A” 42.27
Cost for 1.08 cum. 4490.47
Cost per cum. 4157.85
Say 4157.85
SUB HEAD : 16- ROAD WORK 1223
16.13.2 Water bound macadam
Code Description Unit Quantity Rate Amount
Details of cost for 0.90cum.
Consider a road 6 metres wide and
0.6m. lengthwise and 0.25m cm
average depth =0.90cum.
MATERIAL
Supplying and stacking stone aggregate
53mm to 24mm nominal size at site.
16.3.3 Rate as per Item Number 16.3.3 of
SH: Road Work cum 0.09 1837.25 165.35 A
Supplying and stacking red bajri at site
16.3.8 Rate as per Item Number 16.3.8 of
SH: Road Work cum 0.023 1557.25 35.82 A
Supplying and stacking moorum at site.
16.3.10 Rate as per Item Number 16.3.10 of
SH: Road Work cum 0.022 888.30 19.54 A
LABOUR
For cutting road and taking out soling
and metalling including sorting and
screening.
0114 Beldar day 0.48 645.00 309.60
0115 Coolie day 0.24 645.00 154.80
For relaying soling stone 3.6x0.15
=0.54cum.
0114 Beldar day 0.24 645.00 154.80
0115 Coolie day 0.24 645.00 154.80
For relaying road metal with extra
quantity and consolidation to 0.10m
thickness
3.6x0.10=0.36cum.
0114 Beldar day 0.48 645.00 309.60
0115 Coolie day 0.48 645.00 309.60
0101 Bhisti day 0.10 714.00 71.40
9999 Barrier and chowkidar etc. L.S. 53.82 2.12 114.10
TOTAL 1799.41 W
Add 1 % Water charges on "W-A" 15.79
TOTAL 1815.20 X
Add GST on "X-A" (multiplying
factor 0.1405) 224.03
TOTAL 2039.22 Y
Add 15% CPOH on "Y-A" 272.78
TOTAL 2312.00 Z
Add Cess @ 1% on "Z-A" 20.91
Cost for 0.90 cum. 2332.91
Cost per cum. 2592.12
Say 2592.10
SUB HEAD : 16- ROAD WORK 1224
16.14 Cutting bajri paths and making good the same including supply of extra
quantities of brick aggregate, moorum and red bajri required.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
10x0.075=0.75cum.
MATERIAL
Supplying and stacking 50mm brick
aggregate at site(extra quantity)
0286 Brick Aggregate (Single size) :
50 mm nominal size cum 0.19 650.00 123.50
2260 Carriage of Brick aggregate cum 0.19 178.19 33.86
Supplying and stacking red bajri at site
16.3.8 Rate as per Item Number 16.3.8 of
SH: Road Work cum 0.06 1557.25 93.44 A
Supplying and stacking moorum at site
16.3.10 Rate as per Item Number 16.3.10 of
SH: Road cum 0.06 888.30 53.30 A
LABOUR
For cutting, sorting out, spreading and
consolidation of aggregate
0114 Beldar day 1.60 645.00 1032.00
0115 Coolie day 0.80 645.00 516.00
TOTAL 1852.09 W
Add 1 % Water charges on "W-A" 17.05
TOTAL 1869.14 X
Add GST on "X-A" (multiplying
factor 0.1405) 242.00
TOTAL 2111.14 Y
Add 15% CPOH on "Y-A" 294.66
TOTAL 2405.80 Z
Add Cess @ 1% on "Z-A" 22.59
Cost for 10 sqm. 2428.39
Cost per sqm. 242.84
Say 242.85
16.15 Supplying at site :
16.15.1 R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5
coarsesand : 3 graded stone aggregate 12.5 mm nominal size) with wooden
plugs or 6mm bar nibs wherever required as per direction of Engineer-in-
charge (cost of earth works in excavation, concrete works in foundation to be
paid separately).
Code Description Unit Quantity Rate Amount
Details of cost for 10 posts = 0.336cum
Cubical contents of one post
Area bottom A1 = (15+12.5)/2 x8.75+
½x3.14 x(6.25)²
=120.31+61.38=181.69sqcm.
Area bottom A2 = (10+7.5)/2 x6.25+
½x3.14 x(3.75)² sqm
= 54.68+22.08 = 76.76 sqcm.
SUB HEAD : 16- ROAD WORK 1225
Code Description Unit Quantity Rate Amount
(A1A2)^½ = 118.10sqcm
A1+A2+(A1A2))^½ = 0.03766 sqm
Volume = (1.05)/3x0.03766
= 0.01316 cum
=0.0132cum.
Volume of lower and square portion
(16.5x16.5x75) / 100³ = 0.0204cum.
Total volume = 0.0132+0.0204 cum
= 0.0336 cum.
Qty. for 10 post
= 0.0336x10 = 0.336cum.
Cement concrete 1:1.5:3 (1 Cement :
1.5 Coarse sand : 3 graded stone
aggregate 12.5mm nominal size)
4.1.2 Rate as per item no 4.1.2 of
S.H. Concrete Work. cum 0.336 7783.65 2615.31 A
Extra labour for laying cement concrete
in RCC work
0114 Beldar day 0.034 645.00 21.93
0101 Bhisti day 0.067 714.00 47.84
0123 Mason (brick layer) 1st class day 0.013 784.00 10.19
0124 Mason (brick layer) 2nd class day 0.013 714.00 9.28
0128 Mate day 0.013 714.00 9.28
M.S. Reinforcement
6mm dia. bars
10x4x1.88m = 75.20m+
10x9x0.50m =45.00m = 120.20m
[email protected]/m =26.44kg.
5.22.2 Rate as per Item No.5.22.2 of
SH: Reinforced cement concrete work kg 26.44 87.50 2313.50 A
Centering and shuttering
5.9.1 Rate as per item No.5.9.1 of
SH : Reinforced cement concrete work sqm 6.99 307.95 2152.57 A
6mm C.Plaster 1:2 (1 Cement :
2 fine sand)
Details of cost for 9.88 sqm.
(0.072)/10x9.88 = 0.071
0367 Portland Cement (OPC-43 grade) tonne 0.05 5000.00 250.00
2209 Carriage of Cement tonne 0.05 145.72 7.29
0983 Fine sand (zone IV) cum 0.07 900.00 63.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.07 163.93 11.48
LABOUR
0114 Beldar day 0.05 645.00 32.25
0101 Bhisti day 0.02 714.00 14.28
0155 Mason (average) day 0.64 749.00 479.36
0115 Coolie day 0.80 645.00 516.00
0101 Bhisti day 0.27 714.00 192.78
9999 Hire and running charges of mixer L.S. 1.95 2.12 4.13
9999 Extra for removing burr, cleaning with
wire brushes, pock making with pointed
tool etc. complete L.S. 13.26 2.12 28.11
9999 Scaffolding and sundries L.S. 11.57 2.12 24.53
9977 Carriage of RCC posts L.S. 53.82 2.12 114.10
9999 Wooden plugs or 6mm bar nibs L.S. 12.22 2.12 25.91
SUB HEAD : 16- ROAD WORK 1226
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 8971.77 W
Add 1 % Water charges on “W-A” 18.90
TOTAL 8990.68 X
Add GST on “X-A” (multiplying
factor 0.1405) 268.26
TOTAL 9258.93 Y
Add 15% CPOH on “Y-A” 326.63
TOTAL 9585.57 Z
Add Cess @ 1% on “Z-A” 25.04
Cost for 0.336 cum 9610.61
Cost for one cum 28603.00
Say 28603.00
16.15.2 Welded steel wire fabric of required width having rectangular mesh painted
with two or more coats of enamel paint of approved shade over a coat of
primer (Priming & Painting to be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 27 sqm (209.25 kg).
MATERIAL
Steel wire fabric 0.9m wide rectangular
mesh 75x25mm size weight not less
than 7.75kg/sqm. 30x0.9 = 27sqm
1021 Hard drawn steel wire fabric sqm 27.00 430.00 11610.00
2314 Carriage of Barbed wire tonne 0.209 145.72 30.46
7.75x27=209.25kg=0.209tonne
TOTAL 11640.46 W
Add 1 % Water charges on "W" 116.40
TOTAL 11756.86 X
Add GST on "X" (multiplying
factor 0.1405) 1651.84
TOTAL 13408.70 Y
Add 15% CPOH on "Y" 2011.30
TOTAL 15420.00 Z
Add Cess @ 1% on "Z" 154.20
Cost for 209.25 kg 15574.20
Cost per kg. 74.43
Say 74.45
16.16 Supplying and fixing turn buckles and straining bolts for barbed wire fencing.
Code Description Unit Quantity Rate Amount
Details of cost for one set
MATERIAL
1030 Galvanised steel turn buckles each 1.00 25.00 25.00
1028 Straining bolts each 1.00 80.00 80.00
9977 Carriage of turn buckles and straining
bolts L.S. 2.73 2.12 5.79
Labour for fixing straining bolts and
turn buckles
SUB HEAD : 16- ROAD WORK 1227
Code Description Unit Quantity Rate Amount
0103 Blacksmith 2nd class day 0.10 714.00 71.40
TOTAL 182.19 W
Add 1 % Water charges on “W” 1.82
TOTAL 184.01 X
Add GST on “X” (multiplying
factor 0.1405) 25.85
TOTAL 209.86 Y
Add 15% CPOH on “Y” 31.48
TOTAL 241.34 Z
Add Cess @ 1% on “Z” 2.41
Cost per set 243.76
Say 243.75
16.17 Fencing with R.C.C. post placed at required distance, embedded in cement
concrete blocks, every 15th post, last but one end post and corner post shall be
strutted on both sides and end post one side only, provided with horizontal lines
and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum),
between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I.
binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C.
posts, struts, earth work and concrete to be paid for separately) :- Payment to be
made per metre cost of total length of barbed wire used.
16.17.1 With G.I. barbed wire
Code Description Unit Quantity Rate Amount
Details of cost for 30m
MATERIAL
G.I. barbed wire
30x9 = 270m +
10x6.32 = 63m
Total = 333m
333m @9.38kg/100m =31.24kg = 0.31q
1029 Galvanised steel barbed wire quintal 0.31 5500.00 1705.00
2314 Carriage of Barbed wire tonne 0.03 145.72 4.37
9999 G.I. staples or binding wire L.S. 49.40 2.12 104.73
LABOUR
Labour for fixing costs in line, fixing
and stretching wire
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.50 645.00 322.50
0102 Blacksmith 1st class day 0.50 784.00 392.00
0103 Blacksmith 2nd class day 0.50 714.00 357.00
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 3094.02 W
Add 1 % Water charges on "W" 30.94
TOTAL 3124.96 X
Add GST on "X" (multiplying
factor 0.1405) 439.06
TOTAL 3564.02 Y
Add 15% CPOH on "Y" 534.60
TOTAL 4098.62 Z
Add Cess @ 1% on "Z" 40.99
Cost for 333m 4139.61
Cost per m 12.43
Say 12.45
SUB HEAD : 16- ROAD WORK 1228
16.18 Fencing with angle iron post placed at required distance embedded in cement
concrete blocks, every 15th post, last but one end post and corner post shall be
strutted on both sides and end post on one side only and provided with horizontal
lines and two diagonals interwoven with horizontal wires, of barbed wire weighing
9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I.
staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete
work to be paid for separately). Payment to be made per metre cost of total length
of barbed wire used.
16.18.1 With G.I. barbed wire
Code Description Unit Quantity Rate Amount
Details of cost for 333.24 metre
MATERIAL
G.I. barbed wire
30x9 = 270.00m
2x10x(12+32)1/2 = 63.24
= 333.24m
333.24m @ 9.38kg/100m =31.26 kg
say 0.31 q
1029 Galvanised steel barbed wire quintal 0.31 5500.00 1705.00
2314 Carriage of Barbed wire tonne 0.031 145.72 4.52
Supplying and fixing Turn buckle & staple
16.16 Rate as per Item Number 16.16 of
SH: Road Work each set 10.00 243.75 2437.50 A
9999 G.I. staples L.S. 49.40 2.12 104.73
Labour for fixing posts in line and fixing
and stretching wire:
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.50 645.00 322.50
0102 Blacksmith 1st class day 0.50 784.00 392.00
0103 Blacksmith 2nd class day 0.50 714.00 357.00
TOTAL 5503.01 W
Add 1 % Water charges on "W-A" 30.66
TOTAL 5533.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 435.01
TOTAL 5968.67 Y
Add 15% CPOH on "Y-A" 529.68
TOTAL 6498.35 Z
Add Cess @ 1% on "Z-A" 40.61
Cost for 333.24m 6538.96
Cost per m 19.62
Say 19.60
16.19 Supplying at site Angle iron post & strut of required size including bottom to be
split and bent at right angle in opposite direction for 10 cm length and drilling
holes upto 10 mm dia. etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 1 qunital
MATERIAL
M.S. angle = 1.00 qtl.
Add 5% wastage = 0.05 qtl.
Total = =1.05 qtl
SUB HEAD : 16- ROAD WORK 1229
Code Description Unit Quantity Rate Amount
1007 Structurals such as tees, angles
channels and R.S. joists quintal 1.05 4950.00 5197.50
2205 Carriage of Steel tonne 0.105 145.72 15.30
LABOUR
0103 Blacksmith 2nd class day 0.75 714.00 535.50
0114 Beldar day 0.50 645.00 322.50
For spotting, bending of angle and
drilling holes etc. :
0103 Blacksmith 2nd class day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
9999 Sundries such as drilling bit etc. L.S. 19.76 2.12 41.89
TOTAL 7471.69 W
Add 1 % Water charges on "W" 74.72
TOTAL 7546.41 X
Add GST on "X" (multiplying
factor 0.1405) 1060.27
TOTAL 8606.68 Y
Add 15% CPOH on "Y" 1291.00
TOTAL 9897.68 Z
Add Cess @ 1% on "Z" 98.98
Cost for 1 qunital 9996.66
Cost of one kg 99.97
Say 99.95
16.20 Welded steel wire fabric fencing with posts of specified material and of standard
design placed and embedded in cement concrete blocks 45x45x 60 cm of mix
1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size),
every 15th post, last but one end post and corner post shall be strutted on both
sides and end post on one side only and struts embedded in cement concrete
blocks 70x45x50 cm of the same mix, provided with welded steel wire fabric fixed
between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6
mm bar nibs with G.I. binding wire (cost of posts, welded steel wire fabric, painting,
earth work in excavation and concrete to be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 30 metres i.e.
30x1.20 =36.00sqm
Labour for fixing posts in line fixing and
stretching - welded wire fabric :
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.50 645.00 322.50
0102 Blacksmith 1st class day 0.50 784.00 392.00
0103 Blacksmith 2nd class day 0.50 714.00 357.00
9999 G.I. staple or binding wire L.S. 53.82 2.12 114.10
SUB HEAD : 16- ROAD WORK 1230
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 53.82 2.12 114.10
TOTAL 1479.46 W
Add 1 % Water charges on "W" 14.79
TOTAL 1494.25 X
Add GST on "X" (multiplying
factor 0.1405) 209.94
TOTAL 1704.19 Y
Add 15% CPOH on "Y" 255.63
TOTAL 1959.82 Z
Add Cess @ 1% on "Z" 19.60
Cost for 36 sqm 1979.42
Cost per sqm 54.98
Say 55.00
16.21 Engraving letters in hard stone
Code Description Unit Quantity Rate Amount
Details of cost for 6 letters 8 cm height
LABOUR
For Engraving stone-
0126 Mason (for ornamental stone work)
1st class day 0.38 784.00 297.92
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 312.25 W
Add 1 % Water charges on "W" 3.12
TOTAL 315.37 X
Add GST on "X" (multiplying
factor 0.1405) 44.31
TOTAL 359.68 Y
Add 15% CPOH on "Y" 53.95
TOTAL 413.64 Z
Add Cess @ 1% on "Z" 4.14
Cost of 6 letters of 8cm heights 417.77
Cost per cm. height per letter 8.70
Say 8.70
16.22 Providing and fixing 15x15x90 cm boundary stone of hard stone with top 30 cm
chisel dressed on all four sides including top (cost of excavation, refilling and
concrete etc. to be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for one stone
1151 Boundry stone top chisel dressed
15x15x90 cm each 1.00 80.00 80.00
Labour for fixing
0114 Beldar day 0.12 645.00 77.40
SUB HEAD : 16- ROAD WORK 1231
Code Description Unit Quantity Rate Amount
9977 Carriage to site L.S. 4.16 2.12 8.82
TOTAL 166.22 W
Add 1 % Water charges on "W" 1.66
TOTAL 167.88 X
Add GST on "X" (multiplying
factor 0.1405) 23.59
TOTAL 191.47 Y
Add 15% CPOH on "Y" 28.72
TOTAL 220.19 Z
Add Cess @ 1% on "Z" 2.20
Cost of each. 222.39
Say 222.40
16.23 Providing and fixing 15 cm dia at top, 20 cm at bottom and 90 cm high precast
reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone
aggregate 20 mm nominal size) boundary stone as per standard design, including
finishing smooth with cement mortar 1:3 (1 cement : 3 fine sand) (cost of
excavation, refilling and concreting to be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for one stone
(i) Cement concrete 1:1½:3 (1 cement :
1½ Coarse sand : 3 graded stone
aggregate 20mm nominal size)
Volume of frustum of cone:
L/3 x [A1+A2+sqrt(A1A2)] = 0.825/3 x
[0.095²+0.075² + sqrt(0.095 x 0.075²)]x
3.142=0.01882 (A)
Volume of hemi sphere:
½ x 4 /3 x PI x r³ = ½x(4/ 3)x(22/7)x
0.075³=0.00100 (B)
Total volume = A+B = 0.01982
Say 0.02cum
4.1.2 Rate as per item no 4.1.2 of
S.H. Concrete Work. cum 0.02 7783.65 155.67 A
(ii) Extra for laying cement concerte
in RCC work
LABOUR
0114 Beldar day 0.002 645.00 1.29
0101 Bhisti day 0.004 714.00 2.86
0123 Mason (brick layer) 1st class day 0.0008 784.00 0.63
0124 Mason (brick layer) 2nd class day 0.0008 714.00 0.57
0128 Mate day 0.0008 714.00 0.57
(iii) M.S. reinforcement- 6mm dia. Bar
5.99 metre =5.99x0.22 =1.32kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 1.32 88.95 117.41 A
(iv) Centering and shuttering-
1/2x3.142 (0.19+0.15)x0.825 =0.441 +
3.142/4(0.19)² =0.028 +
1/2x4x3.142(0.075)² = 0.035
= 0.504
Say 0.50sqm.
SUB HEAD : 16- ROAD WORK 1232
Code Description Unit Quantity Rate Amount
5.9.1 Rate as per item No.5.9.1 of
SH : Reinforced cement concrete work sqm 0.50 307.95 153.98 A
(v) 6mm cement plaster 1:3
(1 Cement : 3 fine sand)-
1/2x3.142 (0.19+0.15)x0.825 =0.44 +
3.142/4(0.19)² =0.028 +
1/2x4x3.142(0.075)² = 0.035
= 0.504
Say 0.50sqm.
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.0018 5000.00 9.00
2209 Carriage of Cement tonne 0.0018 145.72 0.26
0983 Fine sand (zone IV) cum 0.0385 900.00 34.65
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.0385 163.93 6.31
Labour for mortar
0114 Beldar day 0.0027 645.00 1.74
0101 Bhisti day 0.0002 714.00 0.14
9999 Hire and running charges of mixer L.S. 0.10 2.12 0.21
9999 Sundries L.S. 0.05 2.12 0.11
Labour for plaster
0155 Mason (average) day 0.026 749.00 19.47
0115 Coolie day 0.038 645.00 24.51
0101 Bhisti day 0.046 714.00 32.84
9999 Extra for removing burr L.S. 0.68 2.12 1.44
9999 Scaffolding, sundries etc. L.S. 0.60 2.12 1.27
(vi) Labour for fixing
0114 Beldar day 0.12 645.00 77.40
9977 Carriage to site L.S. 4.16 2.12 8.82
TOTAL 651.16 W
Add 1 % Water charges on "W-A" 2.24
TOTAL 653.41 X
Add GST on "X-A" (multiplying
factor 0.1405) 31.80
TOTAL 685.21 Y
Add 15% CPOH on "Y-A" 38.72
TOTAL 723.93 Z
Add Cess @ 1% on "Z-A" 2.97
Cost of each. 726.90
Say 726.90
16.24 Providing and fixing precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5
coarse sand : 3 graded stone aggregate 20 mm nominal size) kilometre stone as
per standard design, including finishing smooth in 1:3 cement mortar (1 cement
: 3 fine sand) but excluding the cost of earth work, concrete in foundation, painting
and lettering etc. which shall be paid for separately.
16.24.1 35x111x25 cm size
Code Description Unit Quantity Rate Amount
Details of cost for one stone
(i) Cement concrete 1:1.5:3 (1 cement
:1.5 Coarse sand :3 graded stone
SUB HEAD : 16- ROAD WORK 1233
Code Description Unit Quantity Rate Amount
aggregate 20mm nominal size) in
Kilometre stone
0.35x0.25x0.835m = 0.073
0.37x0.27x0.10m = 0.010
1/2x22/7x(0.175)²x0.25m = 0.012
= 0.095cum
Say 0.10cum.
4.1.2 Rate as per item no 4.1.2 of
S.H. Concrete Work. cum 0.10 7783.65 778.37 A
(ii) Extra for laying cement concrete
in RCC work
0114 Beldar day 0.01 645.00 6.45
0101 Bhisti day 0.02 714.00 14.28
0123 Mason (brick layer) 1st class day 0.004 784.00 3.14
0124 Mason (brick layer) 2nd class day 0.004 714.00 2.86
0128 Mate day 0.004 714.00 2.86
(iii) M.S. reinforcement- 0.10cum @
48.06kg/cum. =4.806kg. Say 4.81kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : Reinforced cement concrete work kg 4.81 88.95 427.85 A
(iv) Centering and shuttering-
(0.35+2x0.25)x0.835 = 0.710 sqm
0.35x0.25 = 0.088sqm
(0.37+2x0.27)x0.10 = 0.091sqm
2x0.37x0.01 = 0.007 sqm
2x2x0.25x0.1 = 0.010sqm
1/2x3.142/4x(0.35)² = 0.048sqm
1/2x0.35x0.25x3.142 = 0.138sqm.
= 1.092sqm. Say 1.09 sqm
5.9.1 Rate as per item No.5.9.1 of
SH : Reinforced cement concrete work sqm 1.09 307.95 335.67 A
(v) 6mm cement plaster 1:3
(1 Cement : 3 fine sand)-
Qty. as per centering and shuttering
= 1.092sqm
0.35x0.835 = 0.292sqm
0.37x0.10 = 0.037sqm
1/2x3.142/4x(0.35)²= 0.048sqm
2x0.37x0.01 = 0.007 sqm
= 1.476 sqm Say 1.48 sqm
0367 Portland Cement (OPC-43 grade) tonne 0.054 5000.00 270.00
2209 Carriage of Cement tonne 0.054 145.72 7.87
0983 Fine sand (zone IV) cum 0.011 900.00 9.90
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.011 163.93 1.80
Labour for mortar
0114 Beldar day 0.008 645.00 5.16
0101 Bhisti day 0.0007 714.00 0.50
9999 Hire and running charges of mixer L.S. 0.03 2.12 0.06
9999 Sundries L.S. 0.13 2.12 0.28
Labour for plaster
0155 Mason (average) day 0.075 749.00 56.18
0115 Coolie day 0.111 645.00 71.60
0101 Bhisti day 0.136 714.00 97.10
9999 Extra for removing burr L.S. 1.95 2.12 4.13
SUB HEAD : 16- ROAD WORK 1234
Code Description Unit Quantity Rate Amount
9999 Scaffolding, sundries etc. L.S. 1.82 2.12 3.86
(vi) Labour for fixing
0114 Beldar day 0.20 645.00 129.00
9977 Carriage to site L.S. 13.52 2.12 28.66
TOTAL 2257.56 W
Add 1 % Water charges on "W-A" 7.16
TOTAL 2264.71 X
Add GST on "X-A" (multiplying
factor 0.1405) 101.56
TOTAL 2366.27 Y
Add 15% CPOH on "Y-A" 123.66
TOTAL 2489.93 Z
Add Cess @ 1% on "Z-A" 9.48
Cost per stone 2499.41
Say 2499.40
16.24.2 50x152.5x25 cm size
Code Description Unit Quantity Rate Amount
Details of cost for one stone
(i) Cement concrete 1:1.5:3 (1 cement
:1.5 Coarse sand :3 graded stone
aggregate 20mm nominal size)
0.50x0.25x1.145m = 0.143cum. +
0.52x0.27x0.13m = 0.018cum. +
1/2x22/7x(0.25)²x0.25m = 0.025cum.
= 0.186 cum.
Say 0.19cum.
4.1.2 Rate as per item no 4.1.2 of
S.H. Concrete Work. cum 0.19 7783.65 1478.89 A
(ii) Extra for laying cement concrete in
RCC work
0114 Beldar day 0.019 645.00 12.26
0101 Bhisti day 0.038 714.00 27.13
0123 Mason (brick layer) 1st class day 0.008 784.00 6.27
0124 Mason (brick layer) 2nd class day 0.008 714.00 5.71
0128 Mate day 0.008 714.00 5.71
(iii) M.S. reinforcement-
0.19cum @48.06kg/cum. =9.131kg.
Say 9.13 kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : Reinforced cement concrete work kg 9.13 88.95 812.11 A
(iv) Centering and shuttering-
(0.50+2x0.25)x1.145 = 1.145 sqm
1/2x(0.25)²x3.142 = 0.098
3.142(0.25)x(0.25) =0.196
(0.52+2x0.27)x0.13 =0.138
2x0.52x0.01 =0.10
2x2x0.25x0.01 =0.010
1x0.50x0.25 =0.125
=1.722sqm. Say 1.72 sqm
SUB HEAD : 16- ROAD WORK 1235
Code Description Unit Quantity Rate Amount
5.9.1 Rate as per item No.5.9.1 of
SH : Reinforced cement concrete work sqm 1.72 307.95 529.67 A
(v) 6mm cement plaster
1:3 (1 Cement : 3 fine sand)-
Qty. as per centering and shuttering
= 1.722sqm. +
0.50x1.145 = 0.572 +
0.52x0.13 = 0.068sqm. +
1/2x(0.25)²x3.142 = 0.098 +
2x0.52x001 = 0.010
= 2.470sqm Sq. 2.47 sqm.
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.09 5000.00 450.00
2209 Carriage of Cement tonne 0.09 145.72 13.11
0983 Fine sand (zone IV) cum 0.20 900.00 180.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.20 163.93 32.79
Labour for mortar
0114 Beldar day 0.013 645.00 8.39
0101 Bhisti day 0.001 714.00 0.71
9999 Hire and running charges of mixer L.S. 0.52 2.12 1.10
9999 Sundries L.S. 0.26 2.12 0.55
Labour for plaster
0155 Mason (average) day 0.126 749.00 94.37
0115 Coolie day 0.185 645.00 119.33
0101 Bhisti day 0.227 714.00 162.08
9999 Extra for removing burr L.S. 3.38 2.12 7.17
9999 Scaffolding, sundries etc. L.S. 2.86 2.12 6.06
(vi) Labour for fixing
0114 Beldar day 0.20 645.00 129.00
9977 Carriage to site L.S. 13.52 2.12 28.66
TOTAL 4111.09 W
Add 1 % Water charges on "W-A" 12.90
TOTAL 4123.99 X
Add GST on "X-A" (multiplying
factor 0.1405) 183.11
TOTAL 4307.10 Y
Add 15% CPOH on "Y-A" 222.96
TOTAL 4530.07 Z
Add Cess @ 1% on "Z-A" 17.09
Cost per stone 4547.16
Say 4547.15
16.24.3 35x93.5x18 cm size
Code Description Unit Quantity Rate Amount
Details of cost for one stone
(i) Cement concrete 1:1.5:3 (1 cement
:1.5 Coarse sand :3 graded stone
aggregate 20mm nominal size)
0.35x0.18x0.835m = 0.0526 cum. +
0.37x0.20x0.10m = 0.0074 cum.
= 0.060 cum.
SUB HEAD : 16- ROAD WORK 1236
Code Description Unit Quantity Rate Amount
4.1.2 Rate as per item no 4.1.2 of
S.H. Concrete Work. cum 0.06 7783.65 467.02 A
(ii) Extra for laying cement concrete in
RCC work
0114 Beldar day 0.006 645.00 3.87
0101 Bhisti day 0.012 714.00 8.57
0123 Mason (brick layer) 1st class day 0.0024 784.00 1.88
0124 Mason (brick layer) 2nd class day 0.0024 714.00 1.71
0128 Mate day 0.0024 714.00 1.71
(iii) M.S. reinforcement-0.06cum @
48.06kg/cum. =2.8836 kg. Say 2.88 kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : Reinforced cement concrete work kg 2.88 88.95 256.18 A
(iv) Centering and shuttering-
(0.35+2x0.18)x0.835 = 0.593 sqm
(0.37+2x0.20)x0.10 = 0.077 sqm
2x0.35x0.18 = 0.126 sqm
2x0.37x0.01 = 0.007sqm
2x2x0.18x0.01 = 0.007sqm
= 0.810 sqm
5.9.1 Rate as per item No.5.9.1 of
SH : Reinforced cement concrete work sqm 0.81 307.95 249.44 A
(v) 6mm cement plaster
1:3 (1 Cement :3 fine sand)-
Qty. as per centering and shuttering
= 0.810sqm
0.35x0.835 = 0.292sqm
0.37x0.10 =0.037sqm
2x0.37x0.01 =0.007sqm
= 1.146 sqm Say 1.15sqm
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.042 5000.00 210.00
2209 Carriage of Cement tonne 0.042 145.72 6.12
0983 Fine sand (zone IV) cum 0.009 900.00 8.10
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.009 163.93 1.48
Labour for mortar
0114 Beldar day 0.006 645.00 3.87
0101 Bhisti day 0.0006 714.00 0.43
9999 Hire and running charges of mixer L.S. 0.26 2.12 0.55
9999 Sundries L.S. 0.13 2.12 0.28
Labour for plaster
0155 Mason (average) day 0.058 749.00 43.44
0115 Coolie day 0.086 645.00 55.47
0101 Bhisti day 0.105 714.00 74.97
9999 Extra for removing burr L.S. 1.56 2.12 3.31
9999 Scaffolding, sundries etc. L.S. 1.30 2.12 2.76
(vi) Labour for fixing
0114 Beldar day 0.10 645.00 64.50
SUB HEAD : 16- ROAD WORK 1237
Code Description Unit Quantity Rate Amount
9977 Carriage to site L.S. 13.52 2.12 28.66
TOTAL 1494.31 W
Add 1 % Water charges on "W-A" 5.22
TOTAL 1499.53 X
Add GST on "X-A" (multiplying
factor 0.1405) 74.03
TOTAL 1573.55 Y
Add 15% CPOH on "Y-A" 90.14
TOTAL 1663.69 Z
Add Cess @ 1% on "Z-A" 6.91
Cost of each 1670.60
Say 1670.60
16.25 Surface dressing on new surface with paving bitumen of grade VG - 10 of approved
quality using 2.25 kg of bitumen per sqm with 1.65 cum of stone chippings 13.2
mm nominal size per 100 sqm of road surface, including consolidation with road
roller of 6 to 8 tonne capacity etc. complete:
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen [email protected] per sqm.
=225 kg = 0.225 tonne.
0309 Paving bitumen VG-10 of approved
quality tonne 0.225 25614.00 5763.15
2211 Carriage of Tar bitumen tonne 0.225 163.93 36.88
Stone aggregate 13.2mm nominal size
@ 1.65cum. per 100sqm.
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.65 1200.00 1980.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.65 163.93 270.48
Steam coal for heating bitumen @
2 quintal per tonne of bitumen
= 2x0.225=0.450q
0370 Coal (steam) quintal 0.45 440.00 198.00
2200 Carriage of steam coal tonne 0.045 187.35 8.43
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate
(a) For cleaning :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating and spraying bitumen :
0130 Mistry day 0.08 784.00 62.72
0138 Sprayer (for bitumen, tar etc.) day 0.11 714.00 78.54
0114 Beldar day 0.93 645.00 599.85
(c) For screening and spreading
aggregate :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 0.93 645.00 599.85
SUB HEAD : 16- ROAD WORK 1238
Code Description Unit Quantity Rate Amount
0115 Coolie day 1.55 645.00 999.75
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.12 800.00 96.00
0007 Hire charges of Coaltar Sprayer day 0.11 350.00 38.50
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 13315.19 W
Add 1 % Water charges on "W" 133.15
TOTAL 13448.34 X
Add GST on "X" (multiplying
factor 0.1405) 1889.49
TOTAL 15337.84 Y
Add 15% CPOH on "Y" 2300.68
TOTAL 17638.51 Z
Add Cess @ 1% on "Z" 176.39
Cost for 100 Sqm. 17814.90
Cost per Sqm. 178.15
Say 178.15
16.26 Surface dressing on new surface in two coats with bitumen of grade VG -10 of
approved quality using 1.8 kg of bitumen per sqm with 1.5 cum of stone chippings
13.2 mm nominal size per 100 sqm of road surface for first coat and 1.1 kg. of
bitumen per sqm with 1.00 cu. metre of stone chippings 11.2 mm nominal size
per 100 sqm of road surface for second coat, including consolidation of each
coat separately with road roller of 6 to 8 tonne capacity etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen S-90/A-90 @ 1.8kg/sqm.
=180kg.=0.18 tonne
0309 Paving bitumen VG-10 of approved
quality tonne 0.18 25614.00 4610.52
2211 Carriage of Tar bitumen tonne 0.18 163.93 29.51
2910 Stone chippings/ screenings 12.5/
13.2 mm nominal size cum 1.50 1200.00 1800.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.50 163.93 245.90
Steam coal for heating bitumen @
2 qunital per tonne
0370 Coal (steam) quintal 0.36 440.00 158.40
SUB HEAD : 16- ROAD WORK 1239
Code Description Unit Quantity Rate Amount
2200 Carriage of steam coal tonne 0.036 187.35 6.74
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate
(a) For cleaning :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating and spraying bitumen :
0130 Mistry day 0.08 784.00 62.72
0138 Sprayer (for bitumen, tar etc.) day 0.11 714.00 78.54
0114 Beldar day 1.38 645.00 890.10
(c) For screening and spreading
aggregate :
0128 Mate day 0.27 714.00 192.78
0114 Beldar day 0.85 645.00 548.25
0115 Coolie day 0.85 645.00 548.25
(d) Consolidation Charges
0113 Chowkidar day 0.11 645.00 70.95
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.12 800.00 96.00
0007 Hire charges of Coaltar Sprayer day 0.11 350.00 38.50
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 16.38 2.12 34.73
Second Coat
MATERIAL
Bitumen S-90/A-90 @ 1.10kg per sqm
= 110kg.=0.11 tonne
0309 Paving bitumen VG-10 of approved
quality tonne 0.11 25614.00 2817.54
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.00 1200.00 1200.00
2211 Carriage of Tar bitumen tonne 0.11 163.93 18.03
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.00 163.93 163.93
Steam coal for heating bitumen @
2 qunital per tonne of bitumen
0370 Coal (steam) quintal 0.22 440.00 96.80
2200 Carriage of steam coal tonne 0.022 187.35 4.12
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate
(a) For cleaning and brushing loose
chips:
0128 Mate day 0.06 714.00 42.84
0115 Coolie day 0.97 645.00 625.65
(b) For heating and spraying bitumen :
0130 Mistry day 0.05 784.00 39.20
0138 Sprayer (for bitumen, tar etc.) day 0.07 714.00 49.98
SUB HEAD : 16- ROAD WORK 1240
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.75 645.00 483.75
(c) For screening and spreading
aggregate :
0128 Mate day 0.07 714.00 49.98
0114 Beldar day 0.62 645.00 399.90
0115 Coolie day 0.62 645.00 399.90
(d) Consolidation Charges
0113 Chowkidar day 0.15 645.00 96.75
0101 Bhisti day 0.06 714.00 42.84
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.06 3000.00 180.00
0007 Hire charges of Coaltar Sprayer day 0.07 350.00 24.50
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.06 800.00 48.00
(e) Misc:
0364 Wire brush each 0.03 20.00 0.60
(with thick wire)
0365 Soft brush each 0.09 20.00 1.80
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 18534.13 W
Add 1 % Water charges on "W" 185.34
TOTAL 18719.47 X
Add GST on "X" (multiplying
factor 0.1405) 2630.09
TOTAL 21349.55 Y
Add 15% CPOH on "Y" 3202.43
TOTAL 24551.99 Z
Add Cess @ 1% on "Z" 245.52
Cost for per 100 sqm. 24797.51
Cost per 1 Sqm. 247.98
Say 248.00
16.27 Surface dressing on old surface with hot bitumen of grade VG - 10 of approved
quality using 1.95 kg of bitumen per sqm with 1.50 cum of stone chippings 11.2
mm nominal size per 100 sqm of road surface, including consolidation with road
roller of 6 to 8 tonne capacity, etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen 1.95kg./sqm.= 195kg. or 0.195t
0309 Paving bitumen VG-10 of approved
quality tonne 0.195 25614.00 4994.73
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.50 1200.00 1800.00
@ 1.50cum. per 100 sqm.
2211 Carriage of Tar bitumen tonne 0.195 163.93 31.97
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.50 163.93 245.90
Steam coal for heating bitumen @2
quintal per tonne of bitumen
0370 Coal (steam) quintal 0.39 440.00 171.60
SUB HEAD : 16- ROAD WORK 1241
Code Description Unit Quantity Rate Amount
2200 Carriage of steam coal tonne 0.039 187.35 7.31
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate etc.
(a) For cleaning :
0128 Mate day 0.06 714.00 42.84
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.97 645.00 625.65
(b) For heating and spraying bitumen :
0130 Mistry day 0.05 784.00 39.20
0138 Sprayer (for bitumen, tar etc.) day 0.06 714.00 42.84
0114 Beldar day 0.69 645.00 445.05
(c) For screening and spreading
aggregate :
0128 Mate day 0.66 714.00 471.24
0114 Beldar day 0.51 645.00 328.95
0115 Coolie day 0.51 645.00 328.95
(d) Consolidation Charges
0113 Chowkidar day 0.15 645.00 96.75
0101 Bhisti day 0.06 714.00 42.84
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.06 3000.00 180.00
0007 Hire charges of Coaltar Sprayer day 0.06 350.00 21.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.06 800.00 48.00
(e) Misc:
Brushes etc. for cleaning
0364 Wire brush each 0.05 20.00 1.00
(with thick wire)
0365 Soft brush each 0.12 20.00 2.40
9999 Brooms and gunny bags L.S. 2.73 2.12 5.79
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 10301.35 W
Add 1 % Water charges on "W" 103.01
TOTAL 10404.36 X
Add GST on "X" (multiplying
factor 0.1405) 1461.81
TOTAL 11866.17 Y
Add 15% CPOH on "Y" 1779.93
TOTAL 13646.10 Z
Add Cess @ 1% on "Z" 136.46
Cost for 100 sqm. 13782.56
Cost per Sqm. 137.83
Say 137.85
SUB HEAD : 16- ROAD WORK 1242
16.28 Surface dressing one coat on new surface with bitumen of specified grade at a
rate of 1.95 kg/sqm of surface area with 1.5 cum of stone chippings 13.2 mm
nominal size per 100 sqm of road surface, including consolidation with road roller
of 6 to 8 tonne capacity , etc. complete :
16.28.1 Using bitumen emulsion (minimum 50% bitumen content- RS grade conforming
to IS : 8887)
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
0310 Bitumen emulsion tonne 0.195 30800.00 6006.00
2211 Carriage of Tar bitumen tonne 0.195 163.93 31.97
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.50 1200.00 1800.00
@1.50 cum. per 100 sqm. = 1.50cum
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.50 163.93 245.90
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For Spraying bitumen emulsion :
0130 Mistry day 0.07 784.00 54.88
0138 Sprayer (for bitumen, tar etc.) day 0.10 714.00 71.40
0114 Beldar day 1.00 645.00 645.00
(c) For screening and spreading
aggregate :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 0.85 645.00 548.25
0115 Coolie day 0.85 645.00 548.25
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.27 714.00 192.78
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0007 Hire charges of Coaltar Sprayer day 0.10 350.00 35.00
(e) Misc:
Brushes etc. for cleaning
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 12689.70 W
Add 1 % Water charges on "W" 126.90
TOTAL 12816.60 X
Add GST on "X" (multiplying
factor 0.1405) 1800.73
TOTAL 14617.33 Y
Add 15% CPOH on "Y" 2192.60
TOTAL 16809.93 Z
Add Cess @ 1% on "Z" 168.10
Cost for 100 sqm. 16978.03
Cost per Sqm. 169.78
Say 169.80
SUB HEAD : 16- ROAD WORK 1243
16.29 Surface dressing one coat on old surface with bitumen of specified grade at the
rate of 1.22 kg/ sqm of surface area with 1.10 cum of stone chippings 11.2 mm
nominal size per 100 sqm of road surface, including consolidation with road roller
of 6 to 8 tonne capacity etc. complete :
16.29.1 Using bitumen emulsion (minimum 50% bitumen content- RS grade conforming
to IS : 8887)
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen emulsion @1.22 kg
per Sqm. =122
kg. or 0.122 tonne
0310 Bitumen emulsion tonne 0.122 30800.00 3757.60
2211 Carriage of Tar bitumen tonne 0.122 163.93 20.00
Stone chippings 11.2mm nominal
size @ 1.10cum. per 100 sqm
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.10 1200.00 1320.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.10 163.93 180.32
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.06 714.00 42.84
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.97 645.00 625.65
(b) For Spraying bitumen emulsion :
0130 Mistry day 0.05 784.00 39.20
0138 Sprayer (for bitumen, tar etc.) day 0.06 714.00 42.84
0114 Beldar day 0.63 645.00 406.35
(c) For screening and spreading
aggregate :
0128 Mate day 0.07 714.00 49.98
0114 Beldar day 0.62 645.00 399.90
0115 Coolie day 0.62 645.00 399.90
(d) Consolidation Charges
0113 Chowkidar day 0.15 645.00 96.75
0101 Bhisti day 0.15 714.00 107.10
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.06 3000.00 180.00
0007 Hire charges of Coaltar Sprayer day 0.06 350.00 21.00
(e) Misc:
Brushes etc. for cleaning
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 2.73 2.12 5.79
SUB HEAD : 16- ROAD WORK 1244
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 8031.17 W
Add 1 % Water charges on “W” 80.31
TOTAL 8111.48 X
Add GST on “X” (multiplying
factor 0.1405) 1139.66
TOTAL 9251.14 Y
Add 15% CPOH on “Y” 1387.67
TOTAL 10638.82 Z
Add Cess @ 1% on “Z” 106.39
Cost for 100 sqm. 10745.20
Cost per Sqm. 107.45
Say 107.45
16.30 Providing and applying tack coat using hot straight run bitumen of grade VG - 10,
including heating the bitumen, spraying the bitumen with mechanically operated
spray unit fitted on bitumen boiler, cleaning and preparing the existing road
surface as per specifications :
16.30.1 On W.B.M. @ 0.75 Kg / sqm
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.075 24500.00 1837.50
2211 Carriage of Tar bitumen tonne 0.075 163.93 12.29
0370 Coal (steam) quintal 0.15 440.00 66.00
2200 Carriage of steam coal tonne 0.015 187.35 2.81
MATERIAL
0364 Wire brush each 0.05 20.00 1.00
(with thick wire)
0365 Soft brush each 0.12 20.00 2.40
9999 Gunny bags L.S. 7.80 2.12 16.54
0007 Hire charges of Coaltar Sprayer day 0.03 350.00 10.50
9999 Sundries L.S. 9.10 2.12 19.29
LABOUR
(a) For cleaning :
0128 Mate day 0.06 714.00 42.84
0114 Beldar day 1.46 645.00 941.70
(b) For heating bitumen:
0114 Beldar day 0.19 645.00 122.55
(c) For applying tack coat:
0114 Beldar day 0.47 645.00 303.15
TOTAL 3378.57 W
Add 1 % Water charges on “W” 33.79
TOTAL 3412.36 X
Add GST on “X” (multiplying
factor 0.1405) 479.44
TOTAL 3891.80 Y
Add 15% CPOH on “Y” 583.77
TOTAL 4475.56 Z
Add Cess @ 1% on “Z” 44.76
Cost for 100 sqm. 4520.32
Cost per Sqm. 45.20
Say 45.20
SUB HEAD : 16- ROAD WORK 1245
16.30.2 On bituminous surface @ 0.50 Kg / sqm
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.05 24500.00 1225.00
2211 Carriage of Tar bitumen tonne 0.05 163.93 8.20
0370 Coal (steam) quintal 0.10 440.00 44.00
2200 Carriage of steam coal tonne 0.01 187.35 1.87
MATERIAL
0364 Wire brush each 0.05 20.00 1.00
(with thick wire)
0365 Soft brush each 0.12 20.00 2.40
9999 Gunny bags L.S. 7.80 2.12 16.54
0007 Hire charges of Coaltar Sprayer day 0.03 350.00 10.50
9999 Sundries L.S. 7.80 2.12 16.54
LABOUR
(a) For cleaning :
0128 Mate day 0.06 714.00 42.84
0114 Beldar day 1.46 645.00 941.70
(b) For heating bitumen:
0114 Beldar day 0.19 645.00 122.55
(c) For applying tack coat:
0114 Beldar day 0.47 645.00 303.15
TOTAL 2736.28 W
Add 1 % Water charges on "W" 27.36
TOTAL 2763.64 X
Add GST on "X" (multiplying
factor 0.1405) 388.29
TOTAL 3151.94 Y
Add 15% CPOH on "Y" 472.79
TOTAL 3624.73 Z
Add Cess @ 1% on "Z" 36.25
Cost for 100 sqm. 3660.97
Cost per Sqm. 36.61
Say 36.60
16.31 Providing and applying tack coat using bitumen emulsion conforming to IS:8887,
using emulsion pressure distributer including preparing the surface & cleaning
with mechanical broom.
16.31.1 With rapid setting bitumen emulsion
16.31.1.1 On W.B.M / W.M.M. @ 0.4kg/sqm
Code Description Unit Quantity Rate Amount
Details of cost for 3500 sqm.
MATERIAL
7382 Bitumen emulsion rapid setting (R.S.)
confirming to IS : 8887-1995 tonne 1.40 18250.00 25550.00
2211 Carriage of Tar bitumen tonne 1.40 163.93 229.50
MACHINERY
0075 Road sweeper (Mechamical Broom) @
1250 sqm. Per hour. hour 2.80 450.00 1260.00
0058 Air compressor hour 2.80 200.00 560.00
SUB HEAD : 16- ROAD WORK 1246
Code Description Unit Quantity Rate Amount
0061 Emulsion Pressure Distributor @
1750 sqm per hour hour 2.00 700.00 1400.00
LABOUR
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 2.00 645.00 1290.00
TOTAL 30346.62 W
Add 1 % Water charges on "W" 303.47
TOTAL 30650.09 X
Add GST on "X" (multiplying
factor 0.1405) 4306.34
TOTAL 34956.43 Y
Add 15% CPOH on "Y" 5243.46
TOTAL 40199.89 Z
Add Cess @ 1% on "Z" 402.00
Cost for 3500 sqm. 40601.89
Cost per Sqm. 11.60
Say 11.60
16.31.1.2 On bituminous surface @ 0.25kg/sqm
Code Description Unit Quantity Rate Amount
Details of cost for 3500 sqm.
MATERIAL
7382 Bitumen emulsion rapid setting (R.S.)
confirming to IS : 8887-1995 tonne 0.875 18250.00 15968.75
2211 Carriage of Tar bitumen tonne 0.875 163.93 143.44
MACHINERY
0075 Road sweeper (Mechamical Broom) @
1250 sqm. Per hour. hour 2.80 450.00 1260.00
0058 Air compressor hour 2.80 200.00 560.00
0061 Emulsion Pressure Distributor @
1750 sqm per hour hour 2.00 700.00 1400.00
LABOUR
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 2.00 645.00 1290.00
TOTAL 20679.31 W
Add 1 % Water charges on "W" 206.79
TOTAL 20886.10 X
Add GST on "X" (multiplying
factor 0.1405) 2934.50
TOTAL 23820.60 Y
Add 15% CPOH on "Y" 3573.09
TOTAL 27393.69 Z
Add Cess @ 1% on "Z" 273.94
Cost for 3500 sqm. 27667.63
Cost per Sqm. 7.91
Say 7.90
SUB HEAD : 16- ROAD WORK 1247
16.31.2 With medium setting bitumen emulsion
16.31.2.1 On W.B.M / W.M.M. @ 0.4kg/sqm
Code Description Unit Quantity Rate Amount
Details of cost for 3500 sqm.
MATERIAL
7742 Bitumen emulsion medium setting
(M.S.) confirming to IS : 8887-1995 tonne 1.40 27100.00 37940.00
2211 Carriage of Tar bitumen tonne 1.40 163.93 229.50
MACHINERY
0075 Road sweeper (Mechamical Broom) @
1250 sqm. Per hour. hour 2.80 450.00 1260.00
0058 Air compressor hour 2.80 200.00 560.00
0061 Emulsion Pressure Distributor @
1750 sqm per hour hour 2.00 700.00 1400.00
LABOUR
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 2.00 645.00 1290.00
TOTAL 42736.62 W
Add 1 % Water charges on "W" 427.37
TOTAL 43163.99 X
Add GST on "X" (multiplying
factor 0.1405) 6064.54
TOTAL 49228.53 Y
Add 15% CPOH on "Y" 7384.28
TOTAL 56612.81 Z
Add Cess @ 1% on "Z" 566.13
Cost for 3500 sqm. 57178.94
Cost per Sqm. 16.34
Say 16.35
16.31.2.2 On bituminous surface @ 0.25kg/sqm
Code Description Unit Quantity Rate Amount
Details of cost for 3500 sqm.
MATERIAL
7742 Bitumen emulsion medium setting
(M.S.) confirming to IS : 8887-1995 tonne 0.875 27100.00 23712.50
2211 Carriage of Tar bitumen tonne 0.875 163.93 143.44
MACHINERY
0075 Road sweeper (Mechamical Broom) @
1250 sqm. Per hour. hour 2.80 450.00 1260.00
0058 Air compressor hour 2.80 200.00 560.00
0061 Emulsion Pressure Distributor @
1750 sqm per hour hour 2.00 700.00 1400.00
LABOUR
0128 Mate day 0.08 714.00 57.12
SUB HEAD : 16- ROAD WORK 1248
Code Description Unit Quantity Rate Amount
0114 Beldar day 2.00 645.00 1290.00
TOTAL 28423.06 W
Add 1 % Water charges on "W" 284.23
TOTAL 28707.29 X
Add GST on "X" (multiplying
factor 0.1405) 4033.37
TOTAL 32740.66 Y
Add 15% CPOH on "Y" 4911.10
TOTAL 37651.76 Z
Add Cess @ 1% on "Z" 376.52
Cost for 3500 sqm. 38028.28
Cost per Sqm. 10.87
Say 10.85
16.32 2 cm premix carpet surfacing with 1.8 cum and 0.90 cum of stone chippings of
13.2 mm size and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of
hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively,
including a tack coat with hot straight run bitumen, including consolidation with
road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for
separately).
16.32.1 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate
of 70 grams per kg of asphalt
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Asphalt 80/100
(i) Hot bitumen @52kg.per cum. of
stone chippings 1.8cum. of 13.2mm
nominal size chippings.
(ii) Hot bitumen @56kg. per cum. of
stone chippings 0.90cum. of 11.2mm
nominal size chippings.
Bitumen :52xl.8+56x0.9=144kg. or
0.144 tonne
MATERIAL
2916 Paving Asphalt VG 10 of approved
quality tonne 0.144 24500.00 3528.00
2211 Carriage of Tar bitumen tonne 0.144 163.93 23.61
Solvent 70gms/kg. for 0.144 t
= 10.08kg.
2914 Solvent kilogram 10.08 30.00 302.40
2342 Carriage of solvent/ Diesel. quintal 0.10 16.39 1.64
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.80 1200.00 2160.00
@1.80cum. per 100 sqm
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.90 1200.00 1080.00
@0.90cum. per 100 sqm
SUB HEAD : 16- ROAD WORK 1249
Code Description Unit Quantity Rate Amount
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.70 163.93 442.61
Steam coal for heating bitumen @
2 quintals per tonne of bitumen
= 2x0.144=0.288q
0370 Coal (steam) quintal 0.288 440.00 126.72
2200 Carriage of steam coal tonne 0.0288 187.35 5.40
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
0114 Beldar day 0.57 645.00 367.65
(c) For screening and spreading
premixed aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 5.00 645.00 3225.00
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
(at barrier for night watch and for
road roller)
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.13 800.00 104.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.04 3500.00 140.00
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 14144.84 W
Add 1 % Water charges on “W” 141.45
TOTAL 14286.29 X
Add GST on “X” (multiplying
factor 0.1405) 2007.22
TOTAL 16293.51 Y
Add 15% CPOH on “Y” 2444.03
TOTAL 18737.54 Z
Add Cess @ 1% on “Z” 187.38
Cost for 100 sqm. 18924.92
Cost per Sqm. 189.25
Say 189.25
SUB HEAD : 16- ROAD WORK 1250
16.32.2 With paving Asphalt grade VG - 30 with no solvent
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Asphalt 60/70
(i) Hot bitumen @52kg.per cum. of
stone chippings 1.8cum. of 13.2mm
nominal size chippings.
(ii) Hot bitumen @56kg. per cum. of
stone chippings 0.90cum. of 11.2mm
nominal size chippings.
Bitumen :52xl.8+56x0.9=144kg. or
0.144 tonne
MATERIAL
7309 Paving Asphalt VG-30 of approved
quality tonne 0.144 38150.00 5493.60
2211 Carriage of Tar bitumen tonne 0.144 163.93 23.61
2910 Stone chippings/ screenings 12.5/
13.2 mm nominal size cum 1.80 1200.00 2160.00
@1.80cum. per 100sqm.
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.90 1200.00 1080.00
@0.90cum. per 100sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.70 163.93 442.61
Steam coal for heating of bitumen @
2 quintals per tonne of bitumen
=2x0.144=0.288q
0370 Coal (steam) quintal 0.288 440.00 126.72
2200 Carriage of steam coal tonne 0.0288 187.35 5.40
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
0114 Beldar day 0.57 645.00 367.65
(c) For screening and spreading
premixed
aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 5.00 645.00 3225.00
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.13 800.00 104.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.04 3500.00 140.00
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
SUB HEAD : 16- ROAD WORK 1251
Code Description Unit Quantity Rate Amount
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 15806.40 W
Add 1 % Water charges on “W” 158.06
TOTAL 15964.47 X
Add GST on “X” (multiplying
factor 0.1405) 2243.01
TOTAL 18207.47 Y
Add 15% CPOH on “Y” 2731.12
TOTAL 20938.60 Z
Add Cess @ 1% on “Z” 209.39
Cost for 100 sqm. 21147.98
Cost per Sqm. 211.48
Say 211.50
16.32.3 With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP: 53
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Refinery Modified Bitumen CRMB 55
(i) Hot bitumen @52kg.per cum. of
stone chippings 1.8cum. of 13.2mm
nominal size chippings.
(ii) Hot bitumen @56kg. per cum. of
stone chippings 0.90cum. of 11.2mm
nominal size chippings.
Modified Bitumen CRMB - 55 (Refinary
produced) :52xl.8+56x0.9=144kg. or
0.144 tonne
MATERIAL
7739 Modified Bitumen Refinary produced
CRMB - 55 tonne 0.144 28000.00 4032.00
2211 Carriage of Tar bitumen tonne 0.144 163.93 23.61
Solvent 70gms/kg. for 0.144 t = 10.08kg
2914 Solvent kilogram 10.08 30.00 302.40
2342 Carriage of solvent/ Diesel. quintal 0.10 16.39 1.64
Stone chippings 13.2mm nominal size
@ 1.80cum. per 100sqm.
2910 Stone chippings/ screenings 12.5/
13.2 mm nominal size cum 1.80 1200.00 2160.00
@1.80cum. per 100sqm.
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.90 1200.00 1080.00
@0.90cum. per 100sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.70 163.93 442.61
Steam coal for heating bitumen @ 2
quintals per tonne of bitumen =
2x0.144=0.288q
0370 Coal (steam) quintal 0.288 440.00 126.72
SUB HEAD : 16- ROAD WORK 1252
Code Description Unit Quantity Rate Amount
2200 Carriage of steam coal tonne 0.0288 187.35 5.40
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
0114 Beldar day 0.57 645.00 367.65
(c) For screening and spreading
premixed aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 5.00 645.00 3225.00
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.13 800.00 104.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.04 3500.00 140.00
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 14648.84 W
Add 1 % Water charges on "W" 146.49
TOTAL 14795.33 X
Add GST on "X" (multiplying
factor 0.1405) 2078.74
TOTAL 16874.07 Y
Add 15% CPOH on "Y" 2531.11
TOTAL 19405.18 Z
Add Cess @ 1% on "Z" 194.05
Cost for 100 sqm. 19599.24
Cost per Sqm. 195.99
Say 196.00
16.33 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of
13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot
bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively,
including a tack coat with hot straight run bitumen, including consolidation with
road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for
separately).
SUB HEAD : 16- ROAD WORK 1253
16.33.1 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate
of 70 grams per kg of asphalt
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Paving Asphalt 80/100
(i) Hot bitumen @52kg.per cum. of
stone chippings @2.25cum. of 13.2mm
nominal size chippings.
(ii) Hot bitumen @56kg. per cum. Of
aggregate @1.12cum. of 11.2mm
nominal size.
Bitumen :52x2.25+56x1.12= 180kg
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.18 24500.00 4410.00
Solvent 0.07x180=12.60kg.
2914 Solvent kilogram 12.6 30.00 378.00
2211 Carriage of Tar bitumen tonne 0.18 163.93 29.51
2342 Carriage of solvent/ Diesel. quintal 0.126 16.39 2.07
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 2.25 1200.00 2700.00
@1.80cum. per 100 sqm.
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.12 1200.00 1344.00
@0.90cum. per 100 sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 3.37 163.93 552.44
2.25+1.12=3.37 cum
Steam coal for heating of bitumen
@2 quintals per tonne of bitumen
=2x0.18=0.36q
0370 Coal (steam) quintal 0.36 440.00 158.40
2200 Carriage of steam coal tonne 0.036 187.35 6.74
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
0114 Beldar day 0.71 645.00 457.95
(c) For screening and spreading
premixed aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 6.25 645.00 4031.25
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.15 800.00 120.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.04 3500.00 140.00
(e) Misc:
SUB HEAD : 16- ROAD WORK 1254
Code Description Unit Quantity Rate Amount
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 16968.18 W
Add 1 % Water charges on "W" 169.68
TOTAL 17137.86 X
Add GST on "X" (multiplying
factor 0.1405) 2407.87
TOTAL 19545.73 Y
Add 15% CPOH on "Y" 2931.86
TOTAL 22477.59 Z
Add Cess @ 1% on "Z" 224.78
Cost for 100 sqm. 22702.37
Cost per Sqm. 227.02
Say 227.00
16.33.2 With paving Asphalt grade VG - 30 with no solvent
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Paving Asphalt 60/70
(i) Hot bitumen @52kg.per cum. of
stone chippings @2.25cum. of 13.2mm
nominal size
(ii) Hot bitumen @56kg. per cum. of
stone [email protected]. of 11.2mm
nominal size size Bitumen
:52x2.25+50xl. 12= 180kg
MATERIAL
7309 Paving Asphalt VG-30 of approved
quality tonne 0.18 38150.00 6867.00
2211 Carriage of Tar bitumen tonne 0.18 163.93 29.51
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 2.25 1200.00 2700.00
@2.25cum. per 100sqm
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.12 1200.00 1344.00
@1.12cum. per 100sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 3.37 163.93 552.44
2.25+1.12=3.37 cum.
0370 Coal (steam) quintal 0.36 440.00 158.40
2200 Carriage of steam coal tonne 0.036 187.35 6.74
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
SUB HEAD : 16- ROAD WORK 1255
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.71 645.00 457.95
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 6.25 645.00 4031.25
1.05x0.18)/0.267 = 0.71 Nos.
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.15 800.00 120.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.04 3500.00 140.00
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 19045.12 W
Add 1 % Water charges on "W" 190.45
TOTAL 19235.57 X
Add GST on "X" (multiplying
factor 0.1405) 2702.60
TOTAL 21938.16 Y
Add 15% CPOH on "Y" 3290.72
TOTAL 25228.89 Z
Add Cess @ 1% on "Z" 252.29
Cost for 100 sqm. 25481.18
Cost per Sqm. 254.81
Say 254.80
16.33.3 With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP: 53
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Refinery Modified Bitumen CRMB 55
(i) Hot bitumen @52kg.per cum. of
stone chippings @2.25cum. of 13.2mm
nominal size chippings.
(ii) Hot bitumen @56kg. per cum. Of
aggregate @1.12cum. of 11.2mm
nominal size.
52x2.25+56x1.12=180kg
7739 Modified Bitumen Refinary produced
CRMB - 55 tonne 0.18 28000.00 5040.00
Solvent 0.07x180=12.60kg
2914 Solvent kilogram 12.6 30.00 378.00
2211 Carriage of Tar bitumen tonne 0.18 163.93 29.51
2342 Carriage of solvent/ Diesel. quintal 0.126 16.39 2.07
SUB HEAD : 16- ROAD WORK 1256
Code Description Unit Quantity Rate Amount
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 2.25 1200.00 2700.00
@2.25 cum. per 100sqm
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.12 1200.00 1344.00
@1.12 cum. per 100sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 3.37 163.93 552.44
2.25+1.12=3.37 cum.+
Steam coal for heating of bitumen @
2 quintals per tonne of bitumen
=2x0.18=0.36q
0370 Coal (steam) quintal 0.36 440.00 158.40
2200 Carriage of steam coal tonne 0.036 187.35 6.74
Labour for cleaning the road surface,
heating and spraying bitumen and
aggregate :
(a) For cleaning :
0128 Mate day 0.08 714.00 57.12
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen:
0114 Beldar day 0.71 645.00 457.95
(c) For screening and spreading premixed
aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 6.25 645.00 4031.25
(d) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.15 800.00 120.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.04 3500.00 140.00
(e) Misc:
0364 Wire brush each 0.11 20.00 2.20
(with thick wire)
0365 Soft brush each 0.32 20.00 6.40
9999 Brooms and gunny bags L.S. 6.76 2.12 14.33
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 17598.18 W
Add 1 % Water charges on "W" 175.98
TOTAL 17774.16 X
Add GST on "X" (multiplying
factor 0.1405) 2497.27
TOTAL 20271.43 Y
Add 15% CPOH on "Y" 3040.71
TOTAL 23312.15 Z
Add Cess @ 1% on "Z" 233.12
Cost for 100 sqm. 23545.27
Cost per Sqm. 235.45
Say 235.45
SUB HEAD : 16- ROAD WORK 1257
16.34 2 cm premix carpet surfacing with 2.4 cum of stone chippings 11.2 mm nominal
size per 100 sqm and bitumen emulsion (medium setting min. 65% bitumen
content) complying with IS : 8887, using 96 kg per cum of chippings, including
consolidation with road roller of 6 to 9 tonne capacity etc. complete.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen emulsion M.S. @ 96kg
per cum. of aggregate
96x2.4=230kg =0.230t
7742 Bitumen emulsion medium setting
(M.S.) confirming to IS : 8887-1995 tonne 0.23 27100.00 6233.00
2211 Carriage of Tar bitumen tonne 0.23 163.93 37.70
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 2.40 1200.00 2880.00
@ 2.4cum. per 100 sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.40 163.93 393.43
LABOUR
(a) For mixing and spreading premix
aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 3.54 645.00 2283.30
(b) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.04 3500.00 140.00
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 12719.20 W
Add 1 % Water charges on "W" 127.19
TOTAL 12846.40 X
Add GST on "X" (multiplying
factor 0.1405) 1804.92
TOTAL 14651.32 Y
Add 15% CPOH on "Y" 2197.70
TOTAL 16849.01 Z
Add Cess @ 1% on "Z" 168.49
Cost for 100 sqm. 17017.50
Cost per Sqm. 170.18
Say 170.20
16.35 2.5 cm premix carpet surfacing with 3 cum of stone chippings 10 mm nominal
size per 100 sqm and bitumen emulsion (medium setting min. 65% bitumen
contents) complying with IS : 8887, using 96 kg per cum of chippings of road
surface, including consolidation with road roller etc complete .
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
MATERIAL
Bitumen emulsion M.S. @
96kg per cum. of aggregate
96x3 = 288 kg = 0.288 t
SUB HEAD : 16- ROAD WORK 1258
Code Description Unit Quantity Rate Amount
7742 Bitumen emulsion medium setting
(M.S.) confirming to IS : 8887-1995 tonne 0.288 27100.00 7804.80
2211 Carriage of Tar bitumen tonne 0.288 163.93 47.21
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 3.00 1200.00 3600.00
@ 3.00 cum. per 100 sqm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 3.00 163.93 491.79
LABOUR
(a) For mixing and spreading premix
aggregate :
0130 Mistry day 0.19 784.00 148.96
0114 Beldar day 4.10 645.00 2644.50
(b) Consolidation Charges
0113 Chowkidar day 0.27 645.00 174.15
0101 Bhisti day 0.11 714.00 78.54
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.11 3000.00 330.00
9999 Sundries L.S. 9.49 2.12 20.12
TOTAL 15340.07 W
Add 1 % Water charges on "W" 153.40
TOTAL 15493.47 X
Add GST on "X" (multiplying
factor 0.1405) 2176.83
TOTAL 17670.30 Y
Add 15% CPOH on "Y" 2650.55
TOTAL 20320.85 Z
Add Cess @ 1% on "Z" 203.21
Cost for 100 sqm. 20524.06
Cost per Sqm. 205.24
Say 205.25
16.36 Providing and laying Bitumen Penetration Macadam with hard stone aggregate
of quality, size and grading as specified, with bitumen of suitable penetration
grade, including required key aggregate as specified, spreading coarse aggregate
with the help of self propelled/ tipper tail mounted aggregate spreader and applying
bitumen by a pressure distributor and then spreading key aggregate with the
help of aggregate spreader complete, including consolidation with road roller of
minimum 8 to 10 tonne capacity to achieve specified values of compaction and
surface accuracy :
16.36.1 For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded
@ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10
sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 370 sqm.
MATERIAL
Taking stone aggregate 40mm = 45%
20mm = 44%
11.2mm = 8%
Stone dust = 3%
SUB HEAD : 16- ROAD WORK 1259
Code Description Unit Quantity Rate Amount
0293 Stone Aggregate (Single size) : 40 mm
nominal size cum 9.99 1300.00 12987.00
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 9.77 1400.00 13678.00
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 1.78 1350.00 2403.00
1159 Stone dust cum 0.6 1100.00 660.00
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 2.33 1400.00 3262.00
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 2.66 1350.00 3591.00
1159 Stone dust cum 0.56 1100.00 616.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 9.99 178.19 1780.12
2202 Carriage of Stone aggregate below
40 mm nominal size i.e. 20 mm cum 12.1 163.93 1983.55
2202 Carriage of Stone aggregate below
40 mm nominal size cum 4.44 163.93 727.85
2267 Carriage of Stone dust cum 1.16 163.93 190.16
2916 Paving Asphalt VG -10 of approved
quality tonne 1.85 24500.00 45325.00
@ 50kg/10 sqm.
2211 Carriage of Tar bitumen tonne 1.85 163.93 303.27
(B) Labour:
0114 Beldar day 16.67 645.00 10752.15
for spreading stone metal
0114 Beldar day 5.33 645.00 3437.85
for hand packing
0114 Beldar day 2.67 645.00 1722.15
dry rolling
0114 Beldar day 1.33 645.00 857.85
Bajri spreader
0138 Sprayer (for bitumen, tar etc.) day 0.67 714.00 478.38
0114 Beldar day 1.33 645.00 857.85
for spreading key aggregate
0114 Beldar day 6.67 645.00 4302.15
for spraying bitumen
0114 Beldar day 0.67 645.00 432.15
of power roller
0128 Mate day 1.77 714.00 1263.78
(C) Machinery :
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.45 800.00 360.00
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.61 3000.00 1830.00
9999 Misc. items as spray nozzle, joint
paper, coconut oil, country soap etc. L.S. 351 2.12 744.12
TOTAL 114545.38 W
Add 1 % Water charges on "W" 1145.45
TOTAL 115690.83 X
Add GST on "X" (multiplying
factor 0.1405) 16254.56
TOTAL 131945.40 Y
Add 15% CPOH on "Y" 19791.81
TOTAL 151737.20 Z
Add Cess @ 1% on "Z" 1517.37
Cost for 370 Sqm. 153254.58
Cost per sqm. 414.20
Say 414.20
SUB HEAD : 16- ROAD WORK 1260
16.36.2 For 75 mm compacted thickness in two layers using stone aggregate of size 63-
41 mm graded @ 0.90 cum per 10 sqm key aggregate of size 20.0 mm graded @
0.18 cum per 10 sqm. With paving asphalt grade VG - 10 @ 68 kg/10 sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 300 sqm.
MATERIAL
Taking output as 300 sqm. for single
layer.
Coarse agg. = 300/10x0.90 = 27 cum.
Key agg = 300/10x0.18 = 5.4 cum.
Bitumen = 300/10x68 = 2.04 t.
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 8.10 178.19 1443.34
0292 Stone Aggregate (Single size) : 50 mm
nominal size cum 8.10 1000.00 8100.00
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 14.58 1400.00 20412.00
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 4.32 1350.00 5832.00
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 2.05 1350.00 2767.50
0296 Stone Aggregate (Single size) : 12.5 mm
nominal size cum 2.57 1350.00 3469.50
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 0.81 1350.00 1093.50
2916 Paving Asphalt VG -10 of approved
quality tonne 2.04 24500.00 49980.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 24.33 163.93 3988.42
2211 Carriage of Tar bitumen tonne 2.04 163.93 334.42
LABOUR
0114 Beldar day 25.00 645.00 16125.00
for spreading stone metal
0114 Beldar day 8.00 645.00 5160.00
for hand packing
0114 Beldar day 4.00 645.00 2580.00
dry rolling
0114 Beldar day 2.00 645.00 1290.00
/Bajri spreader
0138 Sprayer (for bitumen, tar etc.) day 1.00 714.00 714.00
0114 Beldar day 2.00 645.00 1290.00
for spreading key aggregate
0114 Beldar day 10.00 645.00 6450.00
for spraying bitumen
0114 Beldar day 1.00 645.00 645.00
road roller
0128 Mate day 2.65 714.00 1892.10
MACHINERY
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.50 800.00 400.00
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.75 3000.00 2250.00
SUB HEAD : 16- ROAD WORK 1261
Code Description Unit Quantity Rate Amount
9999 Misc. items as spray nozzle, joint
paper, coconut oil, country soap etc. L.S. 429 2.12 909.48
TOTAL 137126.25 W
Add 1 % Water charges on "W" 1371.26
TOTAL 138497.52 X
Add GST on "X" (multiplying
factor 0.1405) 19458.90
TOTAL 157956.42 Y
Add 15% CPOH on "Y" 23693.46
TOTAL 181649.88 Z
Add Cess @ 1% on "Z" 1816.50
Cost for 300 Sqm. 183466.38
Cost per sqm. 611.55
Say 611.55
16.37 Providing and laying bitumen mastic wearing course (as per specifications) with
industrial bitumen of grade 85/25 conforming to IS : 702, prepared by using mastic
cooker and laid to required level and slope, including providing antiskid surface
with bitumen precoated fine grained hard stone chipping of approved size at the
rate of 0.005 cum per 10 sqm and at approximate spacing of 10 cm centre to
centre in both directions, pressed into surface protruding 1 mm to 4 mm over
mastic surface, including cleaning the surface, removal of debris etc. all complete.
(Considering bitumen using 10.2% as per MORTH specification).
16.37.1 25 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for surface area of
17.40 sqm for single layer of 25 mm
finished thickness.
MATERIAL
Taking wearing coat as 1 tonne and
density as 2.3 gm/c.c Volume of
bitumen mastic = 1000/2300= 0.435
cum surface area = 0.435/0.025
= 17.4 sqm.
(i) Bitumen of penetration 85/25 @
10.2% by weight of mix
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.102 34790.00 3548.58
2211 Carriage of Tar bitumen tonne 0.102 163.93 16.72
(ii) Weight of coarse aggregate @ 40%
(1000 - 150) x 40/100 = 340 kg.
Stone aggregate : 340/43.38x0.0283
= 0.222 cum.
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.02 1400.00 28.00
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 0.202 1350.00 272.70
(iii) Weight of fine aggregate @ 15%
850 x15/100 = 127.5 kg., volume of fine
aggregate: 127.5/43.103x0.0283
=0.083 cum
SUB HEAD : 16- ROAD WORK 1262
Code Description Unit Quantity Rate Amount
1159 Stone dust cum 0.083 1100.00 91.30
(iv) Weight of lime stone dust @
45% (850- 340-127.5) = 382.50 kg.,
Volume of lime
stone dust 382.50/2200 =0.174 cum.
0784 Marble dust/ powder cum 0.174 1130.00 196.62
(v) Precoated stone chipping for
surface finish: Volume of chips @
0.005 cum/10 sqm=17.4x0.005/10 =
0.0087 cum say 0.009 cum
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.009 1350.00 12.15
Bitumen for precoated stone chipping
@ 2% =0.009x1600x2/100= 0.288 say
0.30 kg.
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.0003 34790.00 10.44
2211 Carriage of Tar bitumen tonne 0.0003 163.93 0.05
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.231 163.93 37.87
(0.222 + 0.009) =0.231 cum.
2267 Carriage of Stone dust cum 0.083 163.93 13.61
2208 Carriage of Lime cum 0.174 163.93 28.52
LABOUR
0139 Skilled Beldar (for floor rubbing etc.) day 1.50 714.00 1071.00
0130 Mistry day 0.50 784.00 392.00
0138 Sprayer (for bitumen, tar etc.) day 3.50 714.00 2499.00
0139 Skilled Beldar (for floor rubbing etc.) day 0.25 714.00 178.50
0128 Mate day 0.50 714.00 357.00
0016 Mastic Cooker day 0.50 750.00 375.00
9999 sundries (Sealing of joints, placing
angles, wastage materials) L.S. 153.27 2.12 324.93
TOTAL 9453.99 W
Add 1 % Water charges on "W" 94.54
TOTAL 9548.53 X
Add GST on "X" (multiplying
factor 0.1405) 1341.57
TOTAL 10890.10 Y
Add 15% CPOH on "Y" 1633.51
TOTAL 12523.61 Z
Add Cess @ 1% on "Z" 125.24
Cost for 17.40 sqm 12648.85
Cost per sqm 726.95
Say 726.95
16.37.2 40 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for surface area of
10.875sqm for single layer of 40 mm
finished thickness.
SUB HEAD : 16- ROAD WORK 1263
Code Description Unit Quantity Rate Amount
MATERIAL
Taking wearing coat as 1 tonne and
density as 2.3 gm/c.c Volume of
bitumen mastic = 1000/2300= 0.435
cum surface area = 0.435/0.040 =
10.875 sqm.
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.102 34790.00 3548.58
2211 Carriage of Tar bitumen tonne 0.102 163.93 16.72
(ii) Weight of coarse aggregate @ 40%
(1000 - 150) x 40/100 = 340 kg.
Stone aggregate : 340/43.38x0.0283
= 0.222 cum.
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.02 1400.00 28.00
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 0.202 1350.00 272.70
(iii) Weight of fine aggregate @ 15%
850 x15/100 = 127.5 kg., volume of
fine aggregate: 127.5/43.103x0.0283
=0.083 cum
1159 Stone dust cum 0.083 1100.00 91.30
(iv) Weight of lime stone dust @ 45%
(850-340-127.5) = 382.50 kg., Volume
of lime stone dust 382.50/2200
=0.174 cum.
0784 Marble dust/ powder cum 0.174 1130.00 196.62
(v) Precoated stone chipping for
surface finish: Volume of chips @
0.005 cum/10 sqm=17.4x0.005/
10 = 0.0087 cum say 0.009 cum
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.009 1350.00 12.15
Bitumen for precoated stone chipping
@ 2%=0.009x1600x2/100= 0.288
say 0.30 kg.
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.0003 34790.00 10.44
2211 Carriage of Tar bitumen tonne 0.0003 163.93 0.05
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.231 163.93 37.87
(0.222 + 0.009) =0.231 cum
2267 Carriage of Stone dust cum 0.083 163.93 13.61
2208 Carriage of Lime cum 0.174 163.93 28.52
for mastic cooker (Taking capacity of
cooker as one tonne)
LABOUR
0139 Skilled Beldar (for floor rubbing etc.) day 1.50 714.00 1071.00
0130 Mistry day 0.50 784.00 392.00
0138 Sprayer (for bitumen, tar etc.) day 3.50 714.00 2499.00
0139 Skilled Beldar (for floor rubbing etc.) day 0.25 714.00 178.50
0128 Mate day 0.50 714.00 357.00
0016 Mastic Cooker day 0.50 750.00 375.00
SUB HEAD : 16- ROAD WORK 1264
Code Description Unit Quantity Rate Amount
9999 sundries (Sealing of joints, placing
angles, wastage materials) L.S. 153.27 2.12 324.93
TOTAL 9453.99 W
Add 1 % Water charges on "W" 94.54
TOTAL 9548.53 X
Add GST on "X" (multiplying
factor 0.1405) 1341.57
TOTAL 10890.10 Y
Add 15% CPOH on "Y" 1633.51
TOTAL 12523.61 Z
Add Cess @ 1% on "Z" 125.24
Cost for 10.875 sqm 12648.85
Cost per sqm 1163.11
Say 1163.10
16.38 2.5 cm thick bitumastic sheet with hot bitumen of approved quality, using stone
chippings (60% with 12.5 mm nominal size and 40% with 10 mm nominal size) @
1.65 cum per 100 sqm and coarse sand @ 1.65 cum per 100 sqm of road surface
and with bitumen @ 56 kg/cum of stone chippings and @ 128 kg/cum of sand
over a tack coat with hot straight run bitumen, including consolidation with road
roller of 8 to 10 tonne etc. complete. (tack coat to be paid separately) :
16.38.1 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate
of 70 grams per kg of asphalt
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
80/100 bitumen @56kg. per cum. of
aggregate and 128kg. per cum. of sand:
56x1.65=92.4kg. = 0.092t +
128x1.65 = 211.2kg = 0.211t
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.303 24500.00 7423.50
Solvent 0.070 kg. x 303 kg. = 21.21kg
2914 Solvent kilogram 21.21 30.00 636.30
2211 Carriage of Tar bitumen tonne 0.303 163.93 49.67
2342 Carriage of solvent/ Diesel. quintal 0.212 16.39 3.47
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 0.99 1200.00 1188.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.66 1200.00 792.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.65 163.93 270.48
0370 Coal (steam) quintal 0.606 440.00 266.64
2200 Carriage of steam coal tonne 0.0606 187.35 11.35
0982 Coarse sand (zone III) cum 1.65 1500.00 2475.00
2203 Carriage of Coarse sand cum 1.65 163.93 270.48
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
SUB HEAD : 16- ROAD WORK 1265
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.19 645.00 767.55
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.24 784.00 188.16
0114 Beldar day 6.12 645.00 3947.40
(d) Consolidation charges :
0113 Chowkidar day 0.34 645.00 219.30
(at barriers for night watch and for
road roller)
0101 Bhisti day 0.13 714.00 92.82
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.13 3000.00 390.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.21 800.00 168.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.05 3500.00 175.00
(e) Misc :
Wire brush (with thick wire)
0364 Wire brush each 0.13 20.00 2.60
0365 Soft brush each 0.40 20.00 8.00
9999 Brooms and gunny bags L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.97 2.12 19.02
TOTAL 21300.15 W
Add 1 % Water charges on "W" 213.00
TOTAL 21513.15 X
Add GST on "X" (multiplying
factor 0.1405) 3022.60
TOTAL 24535.75 Y
Add 15% CPOH on "Y" 3680.36
TOTAL 28216.11 Z
Add Cess @ 1% on "Z" 282.16
Cost for 100 sqm. 28498.28
Cost per sqm. 284.98
Say 285.00
16.38.2 With paving Asphalt grade VG - 30
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
60/70 bitumen @56kg. per cum. of
aggregate and 128kg. per cum. of sand:
56x1.65=92.4kg. = 0.092t +
128x1.65 = 211.2kg = 0.211t
Total= 0.303t
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 0.303 38150.00 11559.45
2211 Carriage of Tar bitumen tonne 0.303 163.93 49.67
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 0.99 1200.00 1188.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.66 1200.00 792.00
SUB HEAD : 16- ROAD WORK 1266
Code Description Unit Quantity Rate Amount
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.65 163.93 270.48
Steam coal for heating bitumen @
2 quintals per tonne of bitumen
= 2x0.303=0.606q
0370 Coal (steam) quintal 0.606 440.00 266.64
2200 Carriage of steam coal tonne 0.0606 187.35 11.35
0982 Coarse sand (zone III) cum 1.65 1500.00 2475.00
2203 Carriage of Coarse sand cum 1.65 163.93 270.48
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.19 645.00 767.55
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.24 784.00 188.16
0114 Beldar day 6.12 645.00 3947.40
(d) Consolidation charges :
0113 Chowkidar day 0.34 645.00 219.30
(at barriers for night watch and for
road roller)
0101 Bhisti day 0.13 714.00 92.82
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.13 3000.00 390.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.21 800.00 168.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.05 3500.00 175.00
(e) Misc :
0364 Wire brush each 0.13 20.00 2.60
(with thick wire)
0365 Soft brush each 0.40 20.00 8.00
9999 Brooms and gunny bags L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.97 2.12 19.02
TOTAL 24796.33 W
Add 1 % Water charges on "W" 247.96
TOTAL 25044.29 X
Add GST on "X" (multiplying
factor 0.1405) 3518.72
TOTAL 28563.01 Y
Add 15% CPOH on "Y" 4284.45
TOTAL 32847.47 Z
Add Cess @ 1% on "Z" 328.47
Cost for 100 sqm. 33175.94
Cost per sqm. 331.76
Say 331.75
SUB HEAD : 16- ROAD WORK 1267
16.38.3 With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP : 53
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
7739 Modified Bitumen Refinary produced
CRMB - 55 tonne 0.303 28000.00 8484.00
@56kg. per cum. of aggregate and
128kg. per cum. of sand:
56x1.65=92.4kg. = 0.092t +
128x1.65 = 211.2kg = 0.211t
Total = 0.303 t
2914 Solvent kilogram 21.21 30.00 636.30
0.070 kg. x 303 kg. = 21.21kg
2211 Carriage of Tar bitumen tonne 0.303 163.93 49.67
2342 Carriage of solvent/ Diesel. quintal 0.212 16.39 3.47
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 0.99 1200.00 1188.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 0.66 1200.00 792.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 1.65 163.93 270.48
0370 Coal (steam) quintal 0.606 440.00 266.64
2200 Carriage of steam coal tonne 0.0606 187.35 11.35
0982 Coarse sand (zone III) cum 1.65 1500.00 2475.00
2203 Carriage of Coarse sand cum 1.65 163.93 270.48
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.19 645.00 767.55
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.24 784.00 188.16
0114 Beldar day 6.12 645.00 3947.40
(d) Consolidation charges :
0113 Chowkidar day 0.34 645.00 219.30
0101 Bhisti day 0.13 714.00 92.82
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.13 3000.00 390.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.21 800.00 168.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.05 3500.00 175.00
(e) Misc :
0364 Wire brush each 0.13 20.00 2.60
(with thick wire)
0365 Soft brush each 0.40 20.00 8.00
9999 Brooms and gunny bags L.S. 7.15 2.12 15.16
SUB HEAD : 16- ROAD WORK 1268
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.97 2.12 19.02
TOTAL 22360.65 W
Add 1 % Water charges on "W" 223.61
TOTAL 22584.26 X
Add GST on "X" (multiplying
factor 0.1405) 3173.09
TOTAL 25757.35 Y
Add 15% CPOH on "Y" 3863.60
TOTAL 29620.95 Z
Add Cess @ 1% on "Z" 296.21
Cost for 100 sqm. 29917.16
Cost per sqm. 299.17
Say 299.15
16.39 4 cm thick bitumastic sheet with hot bitumen of approved quality, using stone
chippings (60% with 12.5 mm nominal size and 40% with 10 mm nominal size) @
2.60 cum per 100 sqm and coarse sand @ 2.60 cum per 100 sqm of road surface
and with bitumen @ 56 kg/cum of stone chippings and @ 128 kg/cum of sand
over a tack coat with hot straight run bitumen, including consolidation with road
roller of 8 to 10 tonne etc. complete. (tack coat to be paid separately) :
16.39.1 With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate
of 70 grams per kg of asphalt
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.479 24500.00 11735.50
@56kg. per cum. of aggregate and
128kg. per cum. of sand:
56x2.60=145.6kg. = 0.146t +
128x2.60 = 332.8kg = 0.333t
Total = 0.479 t
2914 Solvent kilogram 33.53 30.00 1005.90
0.70kg.x479=33.53kg
2342 Carriage of solvent/ Diesel. quintal 0.335 16.39 5.49
2211 Carriage of Tar bitumen tonne 0.479 163.93 78.52
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.56 1200.00 1872.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.04 1200.00 1248.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.60 163.93 426.22
0982 Coarse sand (zone III) cum 2.60 1500.00 3900.00
2203 Carriage of Coarse sand cum 2.60 163.93 426.22
Steam coal for heating bitumen @ 2
qunitals per tonne of bitumen =
2x0.479=0.958q
0370 Coal (steam) quintal 0.958 440.00 421.52
SUB HEAD : 16- ROAD WORK 1269
Code Description Unit Quantity Rate Amount
2200 Carriage of steam coal tonne 0.0958 187.35 17.95
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.88 645.00 1212.60
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.31 784.00 243.04
0114 Beldar day 9.46 645.00 6101.70
(d) Consolidation charges :
0113 Chowkidar day 0.45 645.00 290.25
0101 Bhisti day 0.18 714.00 128.52
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.18 3000.00 540.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.30 800.00 240.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.03 3500.00 105.00
(e) Misc :
0364 Wire brush each 0.09 20.00 1.80
(with thick wire)
0365 Soft brush each 0.27 20.00 5.40
9999 Brooms and gunny bags L.S. 5.33 2.12 11.30
9999 Sundries L.S. 16.12 2.12 34.17
TOTAL 31971.34 W
Add 1 % Water charges on "W" 319.71
TOTAL 32291.05 X
Add GST on "X" (multiplying
factor 0.1405) 4536.89
TOTAL 36827.95 Y
Add 15% CPOH on "Y" 5524.19
TOTAL 42352.14 Z
Add Cess @ 1% on "Z" 423.52
Cost for 100 sqm. 42775.66
Cost per sqm. 427.76
Say 427.75
16.39.2 With paving asphalt grade VG - 30 with no solvent
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 0.479 38150.00 18273.85
@56kg. per cum. of aggregate and 128kg.
per cum. of sand:
56x2.60=145.6kg. = 0.146t +
128x2.60 = 332.8kg = 0.333t
Total = 0.479 t
SUB HEAD : 16- ROAD WORK 1270
Code Description Unit Quantity Rate Amount
2211 Carriage of Tar bitumen tonne 0.479 163.93 78.52
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.56 1200.00 1872.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.04 1200.00 1248.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.60 163.93 426.22
0982 Coarse sand (zone III) cum 2.60 1500.00 3900.00
2203 Carriage of Coarse sand cum 2.60 163.93 426.22
Steam coal for heating bitumen @
2 qunitals per tonne of bitumen
=2x0.479=0.958 qtl
0370 Coal (steam) quintal 0.958 440.00 421.52
2200 Carriage of steam coal tonne 0.0958 187.35 17.95
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.88 645.00 1212.60
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.31 784.00 243.04
0114 Beldar day 9.46 645.00 6101.70
(d) Consolidation charges :
0113 Chowkidar day 0.45 645.00 290.25
0101 Bhisti day 0.18 714.00 128.52
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.18 3000.00 540.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.30 800.00 240.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.03 3500.00 105.00
(e) Brushes etc. for cleaning :-
0364 Wire brush each 0.09 20.00 1.80
(with thick wire)
0365 Soft brush each 0.27 20.00 5.40
9999 Brooms and gunny bags L.S. 5.33 2.12 11.30
9999 Sundries L.S. 16.12 2.12 34.17
TOTAL 37498.30 W
Add 1 % Water charges on "W" 374.98
TOTAL 37873.28 X
Add GST on "X" (multiplying
factor 0.1405) 5321.20
TOTAL 43194.48 Y
Add 15% CPOH on "Y" 6479.17
TOTAL 49673.65 Z
Add Cess @ 1% on "Z" 496.74
Cost for 100 sqm. 50170.39
Cost per sqm. 501.70
Say 501.70
SUB HEAD : 16- ROAD WORK 1271
16.39.3 With Refinery Modified Bitumen CRMB 55 conforming to IRC: SP : 53
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
7739 Modified Bitumen Refinary produced
CRMB - 55 tonne 0.479 28000.00 13412.00
@56kg. per cum. of aggregate and
128kg. per cum. of sand:
56x2.60=145.6kg. = 0.146t +
128x2.60 = 332.8kg = 0.333t
Total = 0.479 tonne
2914 Solvent kilogram 33.53 30.00 1005.90
0.70kg.x479=33.53kg.
2342 Carriage of solvent/ Diesel. quintal 0.335 16.39 5.49
2211 Carriage of Tar bitumen tonne 0.479 163.93 78.52
2910 Stone chippings/ screenings
12.5/ 13.2 mm nominal size cum 1.56 1200.00 1872.00
2911 Stone chippings/ screenings
10/ 11.2 mm nominal size cum 1.04 1200.00 1248.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 2.60 163.93 426.22
0982 Coarse sand (zone III) cum 2.60 1500.00 3900.00
2203 Carriage of Coarse sand cum 2.60 163.93 426.22
Steam coal for heating bitumen @
2 qunitals per tonne of bitumen =
2x0.479=0.958q
0370 Coal (steam) quintal 0.958 440.00 421.52
2200 Carriage of steam coal tonne 0.0958 187.35 17.95
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.16 714.00 114.24
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(b) For heating bitumen :
0114 Beldar day 1.88 645.00 1212.60
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0130 Mistry day 0.31 784.00 243.04
0114 Beldar day 9.46 645.00 6101.70
(d) Consolidation charges :
0113 Chowkidar day 0.45 645.00 290.25
0101 Bhisti day 0.18 714.00 128.52
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.18 3000.00 540.00
0001 Hire charges of Coaltar Boiler
900 to 1400 litres day 0.30 800.00 240.00
0023 Hot Bitumen mixer 0.5 cum i/c
hand cart day 0.03 3500.00 105.00
(e) Misc :
0364 Wire brush each 0.09 20.00 1.80
(with thick wire)
0365 Soft brush each 0.27 20.00 5.40
9999 Brooms and gunny bags L.S. 5.33 2.12 11.30
SUB HEAD : 16- ROAD WORK 1272
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 16.12 2.12 34.17
TOTAL 33647.84 W
Add 1 % Water charges on "W" 336.48
TOTAL 33984.32 X
Add GST on "X" (multiplying
factor 0.1405) 4774.80
TOTAL 38759.12 Y
Add 15% CPOH on "Y" 5813.87
TOTAL 44572.98 Z
Add Cess @ 1% on "Z" 445.73
Cost for 100 sqm. 45018.71
Cost per sqm. 450.19
Say 450.20
16.40 Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and
retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG
- 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100
sqm of road surface, including rolling and finishing with road roller all complete.
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.0768 24500.00 1881.60
@ 128kg/cum. of sand 128x0.60 =
76.80kg. = 0.0768 m.t
2211 Carriage of Tar bitumen tonne 0.0768 163.93 12.59
0982 Coarse sand (zone III) cum 0.60 1500.00 900.00
2203 Carriage of Coarse sand cum 0.60 163.93 98.36
Steam coal for heating bitumen @
2 qunitals per tonne of bitumen
=2x0.768=0.1536 qtl
0370 Coal (steam) quintal 1.536 440.00 675.84
2200 Carriage of steam coal tonne 0.1536 187.35 28.78
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For cleaning :
0128 Mate day 0.06 714.00 42.84
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.97 645.00 625.65
(b) For heating bitumen :
0114 Beldar day 0.30 645.00 193.50
0.38/96x76.8
(c) For cleaning, mixing and spreading
pre-mix aggregate :
0114 Beldar day 1.11 645.00 715.95
11.39/0.75x0.60
0130 Mistry day 0.05 784.00 39.20
0.06/0.75x0.60
(d) Miscellaneous :
SUB HEAD : 16- ROAD WORK 1273
Code Description Unit Quantity Rate Amount
0113 Chowkidar day 0.15 645.00 96.75
0101 Bhisti day 0.06 714.00 42.84
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.06 3000.00 180.00
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.05 800.00 40.00
0023 Hot Bitumen mixer 0.5 cum i/c hand cart day 0.01 3500.00 35.00
(e) Misc :
0364 Wire brush each 0.05 20.00 1.00
(with thick wire)
0365 Soft brush each 0.12 20.00 2.40
9999 Sundries L.S. 18.20 2.12 38.58
TOTAL 5966.93 W
Add 1 % Water charges on "W" 59.67
TOTAL 6026.60 X
Add GST on "X" (multiplying
factor 0.1405) 846.74
TOTAL 6873.34 Y
Add 15% CPOH on "Y" 1031.00
TOTAL 7904.34 Z
Add Cess @ 1% on "Z" 79.04
Cost for 100 sqm. 7983.38
Cost per sqm. 79.83
Say 79.85
16.41 Providing and laying seal coat over prepared surface of road with bitumen heated
in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of
grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm
size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road
surface, including rolling and finishing with power road roller all complete.
Code Description Unit Quantity Rate Amount
Details of cost for 100sqm.
MATERIAL
2916 Paving Asphalt VG -10 of approved
quality tonne 0.098 24500.00 2401.00
2211 Carriage of Tar bitumen tonne 0.098 163.93 16.07
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 0.90 1400.00 1260.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.90 163.93 147.54
Steam coal for heating bitumen @
2 qunitals per tonne of bitumen
=2x0.098=1.96 qtl
0370 Coal (steam) quintal 1.96 440.00 862.40
2200 Carriage of steam coal tonne 0.196 187.35 36.72
Labour for cleaning road surface,
heating bitumen mixing and spreading
aggregate :
(a) For heating and spraying bitumen :
0130 Mistry day 0.04 784.00 31.36
0138 Sprayer (for bitumen, tar etc.) day 0.06 714.00 42.84
SUB HEAD : 16- ROAD WORK 1274
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.69 645.00 445.05
(b) For cleaning :
0128 Mate day 0.11 714.00 78.54
0114 Beldar day 1.40 645.00 903.00
0115 Coolie day 1.40 645.00 903.00
(c) For screening and spraying aggregate :
0128 Mate day 0.05 714.00 35.70
0114 Beldar day 0.51 645.00 328.95
(d) Misc :
0113 Chowkidar day 0.15 645.00 96.75
0101 Bhisti day 0.06 714.00 42.84
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.06 3000.00 180.00
0007 Hire charges of Coaltar Sprayer day 0.06 350.00 21.00
0001 Hire charges of Coaltar Boiler 900 to
1400 litres day 0.06 800.00 48.00
(e) Misc :
0364 Wire brush each 0.05 20.00 1.00
(with thick wire)
0365 Soft brush each 0.12 20.00 2.40
9999 Sundries L.S. 18.20 2.12 38.58
9999 Brooms and gunny bags L.S. 2.73 2.12 5.79
TOTAL 7928.52 W
Add 1 % Water charges on "W" 79.29
TOTAL 8007.81 X
Add GST on "X" (multiplying
factor 0.1405) 1125.10
TOTAL 9132.91 Y
Add 15% CPOH on "Y" 1369.94
TOTAL 10502.84 Z
Add Cess @ 1% on "Z" 105.03
Cost for 100 sqm. 10607.87
Cost per sqm. 106.08
Say 106.10
16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40
mm nominal size) in pavements, laid to required slope and camber in panels as
required including consolidation finishing and tamping complete.
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 cum.
MATERIAL
0293 Stone Aggregate (Single size) :
40 mm nominal size cum 0.52 1300.00 676.00
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.22 1400.00 308.00
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.11 1350.00 148.50
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 0.52 178.19 92.66
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.33 163.93 54.10
0982 Coarse sand (zone III) cum 0.445 1500.00 667.50
SUB HEAD : 16- ROAD WORK 1275
Code Description Unit Quantity Rate Amount
2203 Carriage of Coarse sand cum 0.445 163.93 72.95
0367 Portland Cement (OPC-43 grade) tonne 0.32 5000.00 1600.00
2209 Carriage of Cement tonne 0.32 145.72 46.63
LABOUR
0155 Mason (average) day 0.10 749.00 74.90
0114 Beldar day 1.63 645.00 1051.35
0101 Bhisti day 0.70 714.00 499.80
MACHINERY
0002 Hire charges of Concrete Mixer
0.25 to 0.40 cum with hooper day 0.077 800.00 61.60
0012 Vibrator (Needle type 40 mm) day 0.07 350.00 24.50
9999 Sundries L.S. 26.00 2.12 55.12
Side shuttering
Taking the slab to be 5cm thick and
width to be 6 metre, length of road
27 metre = 9.90/24.30 = 0.407 sqm
5.9.1 Rate as per item no 5.9.1 of
SH : Reinforced cement concrete work sqm 0.407 307.95 125.34 A
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 5561.97 W
Add 1 % Water charges on "W-A" 54.37
TOTAL 5616.34 X
Add GST on "X-A" (multiplying
factor 0.1405) 771.49
TOTAL 6387.82 Y
Add 15% CPOH on "Y-A" 939.37
TOTAL 7327.20 Z
Add Cess @ 1% on "Z-A" 72.02
Cost for 1 cum. 7399.22
Say 7399.20
16.43 Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi
tracks/ runways, using cement content as per design mix, using coarse sand and
graded stone aggregate of 40 mm nominal size in appropriate proportions as per
approved & specified design criteria, providing dowel bars with sleeve/ tie bars
wherever required, laying at site, spreading and compacting mechanically by using
needle and surface vibrators, levelling to required slope/ camber, finishing with
required texture, including steel form work with sturdy M.S. channel sections,
curing, making provision for contraction/ expansion, construction & longitudinal
joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and
filling joints with approved joint filler and sealants, complete all as per direction
of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie
bars to be paid separately).
Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement
used as per design mix is payable/ recoverable separately.
SUB HEAD : 16- ROAD WORK 1276
16.43.1 Cement concrete prepared with batch mixing machine
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.34 5000.00 1700.00
2209 Carriage of Cement tonne 0.34 145.72 49.54
0293 Stone Aggregate (Single size) :
40 mm nominal size cum 0.52 1300.00 676.00
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.22 1350.00 297.00
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.11 1350.00 148.50
0982 Coarse sand (zone III) cum 0.445 1500.00 667.50
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 0.52 178.19 92.66
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.33 163.93 54.10
2203 Carriage of Coarse sand cum 0.445 163.93 72.95
LABOUR :- FOR MIXING AND LAYING
0114 Beldar day 2.00 645.00 1290.00
0101 Bhisti day 0.27 714.00 192.78
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0128 Mate day 0.04 714.00 28.56
For compaction by vibrator
0155 Mason (average) day 0.07 749.00 52.43
0114 Beldar day 0.07 645.00 45.15
MACHINERY
0004 Production cost of concrete by batch
mix plant. cum 1.00 400.00 400.00
(Assuming 25 cum. per day)
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum 1.00 210.00 210.00
0021 Pin vibrator day 0.025 250.00 6.25
(SHP) with 50 cum. output per day
0022 Surface Vibrator day 0.05 300.00 15.00
with 25 cum. output per day
Add for steel form work
16.43B Rate as per Item Number 16.43B of
SH: Road work cum 1.00 915.85 915.85
9999 Cutting and making joints L.S. 50.00 2.12 106.00
TOTAL 7095.17 W
Add 1 % Water charges on "W" 70.95
TOTAL 7166.12 X
Add GST on "X" (multiplying
factor 0.1405) 1006.84
TOTAL 8172.96 Y
Add 15% CPOH on "Y" 1225.94
TOTAL 9398.91 Z
Add Cess @ 1% on "Z" 93.99
Cost per cum. 9492.89
Say 9492.90
SUB HEAD : 16- ROAD WORK 1277
16.43.2 Cement concrete manufactured in automatic batching plant (RMC plant) i/c
transportation to site in transit mixer
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.34 5000.00 1700.00
2209 Carriage of Cement tonne 0.34 145.72 49.54
0293 Stone Aggregate (Single size) :
40 mm nominal size cum 0.52 1300.00 676.00
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.22 1400.00 308.00
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.11 1350.00 148.50
0982 Coarse sand (zone III) cum 0.445 1500.00 667.50
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 0.52 178.19 92.66
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.33 163.93 54.10
2203 Carriage of Coarse sand cum 0.445 163.93 72.95
LABOUR :- FOR MIXING AND LAYING
0114 Beldar day 2.00 645.00 1290.00
0101 Bhisti day 0.27 714.00 192.78
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0128 Mate day 0.04 714.00 28.56
For compaction by vibrator
0155 Mason (average) day 0.07 749.00 52.43
0114 Beldar day 0.07 645.00 45.15
MACHINERY
0004 Production cost of concrete by
batch mix plant. cum 1.00 400.00 400.00
(Assuming 25 cum. per day)
0029 Carriage of concrete by transit mixer. km/ cum 10.00 37.30 373.00
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum 1.00 210.00 210.00
0021 Pin vibrator day 0.025 250.00 6.25
(SHP) with 50 cum. output per day
0022 Surface Vibrator day 0.05 300.00 15.00
with 25 cum. output per day
Add for steel form work
16.43B Rate as per Item Number 16.43B of
SH: Road work cum 1.00 915.85 915.85
9999 Cutting and making joints L.S. 50.00 2.12 106.00
TOTAL 7479.17 W
Add 1 % Water charges on "W" 74.79
TOTAL 7553.96 X
Add GST on "X" (multiplying
factor 0.1405) 1061.33
TOTAL 8615.29 Y
Add 15% CPOH on "Y" 1292.29
TOTAL 9907.59 Z
Add Cess @ 1% on "Z" 99.08
Cost per cum. 10006.66
Say 10006.65
SUB HEAD : 16- ROAD WORK 1278
16.43A Annexure ‘A’ to Item number 16.43
Code Description Unit Quantity Rate Amount
Details of cost for 8.5 cum.
MATERIAL:
(i) Painting with primer
(i) Construction joint 6.15m. long
30cm deep
6.15x(0.30+0.01)= 1.91sqm.+
(ii) Dummy joints
4.61m long and 10cm deep 10mm wide
4.6 lx(0.10+0.10+0.01) = 0.97 sqm.
= 2.88 sqm.
2.88sqm. @0.26 lit./sqm. = 0.75 lit. +
Add 5% wastage = 0.03
Total =0.78 lit
0316 Bitumen solution primer of approved
quality litre 0.78 47.00 36.66
9977 Carriage L.S. 0.91 2.12 1.93
(ii) Joint sealing compound (GradeA)
for construction joint 6.15m long 10mm
wide 25mm deep.
6.15x2x2.5cm = 3075cucm
For dummy joints
461xl.0xl0cm. = 4610cucm.
Total = 7685 cum
Add 5% wastage = 384 cucm
Total = 8069 cucm
Say 8.07 cudm. @1.2kg/cudm = 9.68 kg
0314 Bitumen hot sealing compound : grade A kilogram 9.68 29.00 280.72
9977 Carriage L.S. 0.91 2.12 1.93
0370 Coal (steam) quintal 0.015 440.00 6.60
9977 Carriage L.S. 0.91 2.12 1.93
LABOUR:
(ii) For applying primer qty. = 2.88 sqm
0123 Mason (brick layer) 1st class day 3.00 784.00 2352.00
0131 Painter day 0.10 714.00 71.40
(iii) Labour for heating and filling sealing
compound.
0124 Mason (brick layer) 2nd class day 0.25 714.00 178.50
(iv) Beldar for heating, carrying and
pouring of bitumen
0114 Beldar day 0.68 645.00 438.60
TOTAL 3370.27
Cost for 8.5 cum 3370.27
Cost per cum. 396.50
Say 396.50
16.43B Annexure ‘B’ to Item number 16.43
Code Description Unit Quantity Rate Amount
ANALYSIS OF ANNEXTURE 'B'
16.43B (Required in 16.43)
STEEL FORM WORK :
Part-I Cost of materials :
SUB HEAD : 16- ROAD WORK 1279
Code Description Unit Quantity Rate Amount
Assuming that pavement 30m long
22.5m wide and 0.30m deep having
panel size 6.15x4.61x0.30m or 8.50cu.
laid in a day of 8 hrs. Hence form work
to be provided for 2 days.
MATERIAL
22x30.75 = 676.50
2x46.10 = 92.20
Total = 768.70m.
768.70 @ 83.10 kg/ m = 25.44 M.T.
Assuming that channel will become
unserviceable after use for 5000 slab
(100 times) and salvage value of steel
shall fetch 20% of its basic cost.
1007 Structurals such as tees, angles
channels and R.S. joists quintal 0.0407104 4950.00 201.52
2205 Carriage of Steel tonne 0.00407104 145.72 0.59
Part-II Labour for assembling,
errection, dismeritelling and cleaning
the shuttering. Assuming that 255
labour for steel shuttering shall be
required as compared to timber
shuttering. Contact area of 50 slabs of
steel shuttering.
Long channel = 11x20x0.30 = 66.00
= 2x45.10x0.30 = 27.06
Total= 93.06
LABOUR
0103 Blacksmith 2nd class day 2.86 714.00 2042.04
0114 Beldar day 2.86 645.00 1844.70
Carriage of steel for extra lead of runway
0114 Beldar day 5.73 645.00 3695.85
TOTAL 7784.70
Cost for 50 slabs / 8.5 cum 7784.70
Cost per cum. 915.85
Say 915.85
16.44 Extra for providing and mixing hardening compound of approved quality as per
manufacturer's specification in cement concrete.
Code Description Unit Quantity Rate Amount
Details of cost for 1 litre
MATERIAL
7254 Hardening compound litre 1.00 36.00 36.00
(including cartage)
TOTAL 36.00 W
Add 1 % Water charges on "W" 0.36
TOTAL 36.36 X
Add GST on "X" (multiplying
factor 0.1405) 5.11
TOTAL 41.47 Y
Add 15% CPOH on "Y" 6.22
TOTAL 47.69 Z
Add Cess @ 1% on "Z" 0.48
Cost per litre 48.17
Say 48.15
SUB HEAD : 16- ROAD WORK 1280
16.45 Providing and fixing pre-moulded joint filler in expansion joints of RCC roads /
CC pavements after making the joints dust free with high pressure air jet cleaners,
all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers
shall be made of bitumen hot sealing compound impregnated fibre board having
impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834
for hot sealing bitumen compound grade A.)
Code Description Unit Quantity Rate Amount
Details of cost for 12 mm thick 15cm
deep and 300m in length
MATERIAL
0317 Premoulded joint filler board 12 mm
thick (Rate inclusive of carriage)
= 300x0.15 = 45 sqm. sqm 45.00 360.00 16200.00
Labour for cutting the board in strips,
making the joints clean and dust free
and fixing etc. :
0112 Carpenter 2nd class day 1.00 714.00 714.00
0114 Beldar day 3.00 645.00 1935.00
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 18906.05 W
Add 1 % Water charges on “W” 189.06
TOTAL 19095.11 X
Add GST on “X” (multiplying
factor 0.1405) 2682.86
TOTAL 21777.97 Y
Add 15% CPOH on “Y” 3266.70
TOTAL 25044.67 Z
Add Cess @ 1% on “Z” 250.45
Cost for 300m length, 12mm width
and 15cm depth 25295.12
Cost for one cm. depth one cm. width
per metre length. 4.68
Say 4.70
16.46 Providing and filling in position rubberized bitumen hot sealing compound for
sealing of expansion joints in roads / pavements all complete as per direction of
the Engineer-in-Charge.
16.46.1 Using grade 'A' sealing compound conforming to IS: 1834.
Code Description Unit Quantity Rate Amount
Details of cost for 12 mm wide 25 mm
deep and 300 metres in length.
Sealing compound-
300x0.012x0.025 = 0.09cum.
Weight 1020 kg. per cum.
= 1020x0.09 = 91.80 kg
MATERIAL
0314 Bitumen hot sealing compound : grade A kilogram 91.80 29.00 2662.20
2211 Carriage of Tar bitumen tonne 0.092 163.93 15.08
91.8 kg = 0.0918 Say 0.092 tonne
Labour for filling :
0124 Mason (brick layer) 2nd class day 1.00 714.00 714.00
SUB HEAD : 16- ROAD WORK 1281
Code Description Unit Quantity Rate Amount
0114 Beldar day 2.50 645.00 1612.50
9999 Sundries L.S. 20.67 2.12 43.82
TOTAL 5047.60 W
Add 1 % Water charges on "W" 50.48
TOTAL 5098.08 X
Add GST on "X" (multiplying
factor 0.1405) 716.28
TOTAL 5814.36 Y
Add 15% CPOH on "Y" 872.15
TOTAL 6686.51 Z
Add Cess @ 1% on "Z" 66.87
Cost for 12 mm depth, 25 mm width
and 300m length 6753.38
Cost for one cm. depth one cm. width
permetre length. 7.50
Say 7.50
16.47 Painting runway/taxi track/apron marking with adequate nos of coats to give
uniform finish with road marking paint of superior make as approved by the
Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other
foreign material etc. and lining out complete.
16.47.1 New work (Two or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10sqm.
MATERIAL
1st Coat - 1.66 +
2nd Coat -1.13
Total = 2.79
7256 Superior quality road marking paint
(water based) litre 2.79 130.00 362.70
9977 Carriage of paint L.S. 5.07 2.12 10.75
LABOUR
0131 Painter day 0.54 714.00 385.56
0114 Beldar day 0.54 645.00 348.30
9999 Sundries L.S. 36.40 2.12 77.17
(including painting brush, wire brush,
labour for controlling traffic and other
T&P etc.)
TOTAL 1184.48 W
Add 1 % Water charges on "W" 11.84
TOTAL 1196.32 X
Add GST on "X" (multiplying
factor 0.1405) 168.08
TOTAL 1364.40 Y
Add 15% CPOH on "Y" 204.66
TOTAL 1569.06 Z
Add Cess @ 1% on "Z" 15.69
Cost for 10 sqm. 1584.76
Cost per sqm. 158.48
Say 158.50
SUB HEAD : 16- ROAD WORK 1282
16.47.2 Old work (One or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10sqm.
MATERIAL
7256 Superior quality road marking paint
(water based) litre 1.66 130.00 215.80
9977 Carriage of paint L.S. 1.12 2.12 2.37
LABOUR
0131 Painter day 0.36 714.00 257.04
0114 Beldar day 0.36 645.00 232.20
9999 Sundries L.S. 24.44 2.12 51.81
(including painting brush, wire brush,
labour for controlling traffic and other
T&P etc.)
TOTAL 759.23 W
Add 1 % Water charges on "W" 7.59
TOTAL 766.82 X
Add GST on "X" (multiplying
factor 0.1405) 107.74
TOTAL 874.56 Y
Add 15% CPOH on "Y" 131.18
TOTAL 1005.74 Z
Add Cess @ 1% on "Z" 10.06
Cost for 10 sqm. 1015.80
Cost per sqm. 101.58
Say 101.60
16.48 Painting road surface marking with adequate nos of coats to give uniform finish
with ready mixed road marking paint conforming to IS : 164, on bituminous surface
in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease
and foreign material etc. complete.
16.48.1 New work (Two or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10sqm.
MATERIAL
7255 Road marking paint (spirit based) litre 1.48 115.00 170.20
(confirming to IS 164 spirit base)
9977 Carriage of paint (1.48/0.8x0.08x6.9) L.S. 2.65 2.12 5.62
LABOUR
0128 Mate day 0.10 714.00 71.40
0131 Painter day 0.54 714.00 385.56
0114 Beldar day 1.68 645.00 1083.60
for stretching of rope & errecting of
barricading
SUB HEAD : 16- ROAD WORK 1283
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 36.40 2.12 77.17
(including painting brush, wire brush,
labour for controlling traffic and other
T&P etc.)
TOTAL 1793.55 W
Add 1 % Water charges on "W" 17.94
TOTAL 1811.48 X
Add GST on "X" (multiplying
factor 0.1405) 254.51
TOTAL 2065.99 Y
Add 15% CPOH on "Y" 309.90
TOTAL 2375.89 Z
Add Cess @ 1% on "Z" 23.76
Cost for 10 sqm. 2399.65
Cost per sqm. 239.97
Say 239.95
16.48.2 Old work (One or more coats)
Code Description Unit Quantity Rate Amount
Details of cost for 10sqm.
MATERIAL
7255 Road marking paint (spirit based) litre 0.89 115.00 102.35
(confirming to IS 164 spirit base)
9977 Carriage of paint. L.S. 0.65 2.12 1.38
LABOUR
0128 Mate day 0.06 714.00 42.84
0131 Painter day 0.36 714.00 257.04
0114 Beldar day 1.12 645.00 722.40
(stretching of rope & errecting of
barricading etc.)
9999 Sundries L.S. 24.44 2.12 51.81
(including painting brush, wire brush,
labour for controlling traffic and other
T&P etc.)
TOTAL 1177.82 W
Add 1 % Water charges on “W” 11.78
TOTAL 1189.60 X
Add GST on “X” (multiplying
factor 0.1405) 167.14
TOTAL 1356.74 Y
Add 15% CPOH on “Y” 203.51
TOTAL 1560.25 Z
Add Cess @ 1% on “Z” 15.60
Cost for 10 sqm. 1575.85
Cost per sqm. 157.59
Say 157.60
SUB HEAD : 16- ROAD WORK 1284
16.49 Making bell mouth opening/ entrance of size 100x50x50 cm for drainage pipe
under footpath, including providing cement concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) for shape of bell mouth,
including plastering providing and fixing precast R.C.C./ S.F.R.C. slab including
plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on
exposed surface of the slab & bell mouth including centring, shuttering & neat
cement punning inside the bell mouth etc. all complete.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Nos.
(i) Earth work in excavation
Channel :- 10x1x1.00x0.20x0.15 = 0.30+
Bell mouth :-10x1x1.00x0.50x
(0.18+0.075)/2 = 0.64
Total = 0.94
MATERIAL
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 0.94 286.85 269.64 A
(ii) Cement concrete 1:4:8
Channel :-10x1x1.00x0.20x0.075
= 0.15 cum.
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.15 6326.05 948.91 A
(iii) Cement concrete 1:3:6
Channel
10x1x1.00x0.20x0.75 = 0.15 +
Bed of bell mouth :
10x1x1.00x0.50x(0.18+0.075)/2 = 0.64 +
Haunches portion
10x2x(0.35+0.075)/2x0.25x0.375 = 0.40 +
Rect part :-
10x2x0.35x0.25x0.375 = 0.65 +
Quadrant portion :-
10x1[(0.30x0.30)-3.142/4(0.30)²]x
0.30 =0.06+
Central middle part :-
10x1x0.30x0.25x0.075 = 0.05
Total = 1.95 cum.
4.1.5 (Rate as per item no.4.1.5
S.H. : Cement Concrete) cum 1.95 6833.40 13325.13 A
(iv) RCC in shelves
10x1x1.00x0.50x0.05 = 0.25cum.
5.3 Rate as per item no. 5.3
SH : Reinforced cement concrete work cum 0.25 10719.30 2679.83 A
(v) Reinforcement for RCC @100kg/cum.
0.25x100=25kg.
5.22.1 Rate as per item no. 5.22.1
SH : Reinforced cement concrete work kg 25.00 88.95 2223.75 A
(vi) Centering and shuttering
For shelves (sides)
10x2(1.00+0.50)x0.05 = 1.50+
Front side of bell mouth :
10x2(0.446)x0.375 = 3.34 +
Pipe portion:
10x[0.30x0.375-3.142/4(030)²] = 0.04 +
Out side of bell mouth
SUB HEAD : 16- ROAD WORK 1285
Code Description Unit Quantity Rate Amount
Total= 10x(1.00 =0.50)x0.45 = 9.00+
Deduct pipe opening
Total =10x0.785x0.30x0.30 = (-)0.71
Total = 13.17
5.9.1 Rate as per item No.5.9.1 of SH : RCC sqm 13.17 307.95 4055.70 A
(vii) cement plaster on RCC slab
10x1.00x0.50 = 5.00 +
10x2(1.00+0.50)x0.05 = 1.50+
Total = 6.50 sqm.
5.23 Rate as per item no.13.16.1 sqm 6.50 253.05 1644.83 A
(viii) Neat cement punning:
Qty. same as marked (x) at (9vi) =
Total =3.34+0.04 = 3.38 sqm.
Channel portion:
10x1x(0.85+0.30)/2x0.25 = 1.43
Total = 4.81
13.18 Rate as per item no.13.18 S.H. Finishing sqm 4.81 67.80 326.12 A
0367 Portland Cement (OPC-43 grade) tonne 0.024 5000.00 120.00
2209 Carriage of Cement tonne 0.024 145.72 3.50
0983 Fine sand (zone IV) cum 0.05 900.00 45.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.05 163.93 8.20
LABOUR
0114 Beldar day 0.035 645.00 22.58
0101 Bhisti day 0.003 714.00 2.14
9999 Hire charges of mixer L.S. 1.27 2.12 2.69
9999 Sundries L.S. 1.27 2.12 2.69
Labour for plaster
0155 Mason (average) day 0.33 749.00 247.17
0115 Coolie day 0.488 645.00 314.76
0101 Bhisti day 0.60 714.00 428.40
9999 Extra for removing burr L.S. 8.71 2.12 18.47
9999 Scaffolding L.S. 7.62 2.12 16.15
TOTAL 26705.64 W
Add 1 % Water charges on "W-A" 12.32
TOTAL 26717.96 X
Add GST on "X-A" (multiplying
factor 0.1405) 174.79
TOTAL 26892.75 Y
Add 15% CPOH on "Y-A" 212.83
TOTAL 27105.58 Z
Add Cess @ 1% on "Z-A" 16.32
Cost for 10 nos. 27121.89
Cost for one bell mouth 2712.19
Say 2712.20
SUB HEAD : 16- ROAD WORK 1286
16.50 Providing and fixing Glow studs of size 100x20 mm made of heavy duty body
shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact
polystyrene) or ABS having electronically welded micro- prismatic lens with
abrasion resistant coating as approved by Engineer in charge. The glow stud
shall support a load of 13635 kg tested in accordance with ASTM D4280. The
slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective
panels on both sides with at least 12 cm of reflective area up each side. The
luminance intensity should be as per the specification and shall be tested as
described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs
shall be fixed to the Road surface using the adhesive conforming to IS, as per
procedure recommended by the manufacturer complete and as per direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 15 Nos.
MATERIAL
7426 Cat's eye each 15.00 80.00 1200.00
9977 Carriage of cats eyes L.S. 2.60 2.12 5.51
LABOUR
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 39.00 2.12 82.68
(including material required for fixing
cats eyes and providing barricading
to divert
traffic)
TOTAL 1967.69 W
Add 1 % Water charges on "W" 19.68
TOTAL 1987.37 X
Add GST on "X" (multiplying
factor 0.1405) 279.23
TOTAL 2266.59 Y
Add 15% CPOH on "Y" 339.99
TOTAL 2606.58 Z
Add Cess @ 1% on "Z" 26.07
Cost for 15 Nos. 2632.65
Cost for one cat's eye. 175.51
Say 175.50
16.51 Preparation of sub-base road pavement with commercial dry lime (slaked), fly
ash stabilised soil with a mix of 3% lime, 12% fly ash and 85% local suitable soil
by weight, so as to achieve minimum field C.B.R. of 20, including mixing, rolling
with road roller curing etc. all complete.
16.51.1 Minimum thickness 15 cm
Code Description Unit Quantity Rate Amount
Details of cost for 6.67 sqm. or 1 cum.
MATERIAL
0777 Dry hydrated lime (factory made) quintal 0.41 290.00 118.90
2208 Carriage of Lime cum 0.068 163.93 11.15
1980 Flyash cum 0.277 11.00 3.05
2267 Carriage of Stone dust cum 0.277 163.93 45.41
SUB HEAD : 16- ROAD WORK 1287
Code Description Unit Quantity Rate Amount
LABOUR
(i)For earth work :
0114 Beldar day 0.116 645.00 74.82
0115 Coolie day 0.116 645.00 74.82
0979 Royalty for good earth cum 0.655 40.00 26.20
2241 Carriage of Good earth cum 0.655 204.92 134.22
(ii) For mixing :
0114 Beldar day 0.025 645.00 16.13
0115 Coolie day 0.025 645.00 16.13
(iii) For rolling layers :
0113 Chowkidar day 0.0008 645.00 0.52
0003 Hire charges of Diesel Road Roller -
8 to 10 tonne day 0.0008 3000.00 2.40
9999 Sundries L.S. 0.18 2.12 0.38
(iv) Labour for spreading and watering :
0114 Beldar day 0.26 645.00 167.70
0115 Coolie day 0.26 645.00 167.70
0101 Bhisti day 0.18 714.00 128.52
TOTAL 988.03 W
Add 1 % Water charges on "W" 9.88
TOTAL 997.91 X
Add GST on "X" (multiplying
factor 0.1405) 140.21
TOTAL 1138.12 Y
Add 15% CPOH on "Y" 170.72
TOTAL 1308.84 Z
Add Cess @ 1% on "Z" 13.09
Cost for 1 cum. 1321.93
Say 1321.95
16.52 Providing and fixing precast lime fly ash concrete blocks 1:2:3:6 (1 lime: 2 fly ash
: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), including finishing
with 10mm thick cement mortar 1:3 (1 cement : 3 coarse sand) in foot paths,
including preparation of sub grade with a hand rammer, laying 10 mm thick leveling
course of fine sand (jamuna sand) and filling the joints with fine sand.
Code Description Unit Quantity Rate Amount
Details of cost for a path of area
10sqm/0.9cum.
No. of blocks required for 10sqm.
= 108 nos.
(a) Concrete in blocks
(108x0.30x0.30x0.09 = 0.875 cum.)
16.52Y Rate as per sub analysis Item Number
16.52Y of SH:Road Work cum 0.875 3727.10 3261.21
(b) Labour for surface excavation :
0114 Beldar day 0.72 645.00 464.40
0115 Coolie day 0.60 645.00 387.00
(c) For levelling course of fine sand
6501 Sand zone V (Jamuna) cum 0.10 1300.00 130.00
2335 Carriage of Jamuna sand cum 0.10 163.93 16.39
SUB HEAD : 16- ROAD WORK 1288
Code Description Unit Quantity Rate Amount
LABOUR
0114 Beldar day 0.0089 645.00 5.74
0115 Coolie day 0.0107 645.00 6.90
0101 Bhisti day 0.0035 714.00 2.50
(d) For finishing with 10mm thick
cement plaster
cement plaster with cement mortar
1:3(1 Cement: 3 Coarse sand)
qty. for 9.72sqm. = 0.0972 cum
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.0972 5024.15 488.35
0155 Mason (average) day 0.787 749.00 589.46
0115 Coolie day 0.787 645.00 507.62
0101 Bhisti day 0.262 714.00 187.07
9999 Scaffolding and sundries L.S. 12.22 2.12 25.91
(e) For laying blocks and filling joints
with Jamuna sand for filling joints
5mm (av.) thick
6501 Sand zone V (Jamuna) cum 0.005 1300.00 6.50
2335 Carriage of Jamuna sand cum 0.005 163.93 0.82
0123 Mason (brick layer) 1st class day 0.90 784.00 705.60
0115 Coolie day 1.98 645.00 1277.10
0101 Bhisti day 0.05 714.00 35.70
TOTAL 8098.27 W
Add 1 % Water charges on "W" 80.98
TOTAL 8179.25 X
Add GST on "X" (multiplying
factor 0.1405) 1149.18
TOTAL 9328.43 Y
Add 15% CPOH on "Y" 1399.26
TOTAL 10727.70 Z
Add Cess @ 1% on "Z" 107.28
Cost for 10sqm. or 0.9cum. 10834.97
Rate per cum. 12038.86
Say 12038.85
16.52X Sub Analysis X for sub analysis item Number 16.52Y
Code Description Unit Quantity Rate Amount
Sub Analysis 16.52X for use in sub
analysis of 16.52Y
Details of cost for 1cum of lime Flyash
mortar 1:2:3 (lime:2 flyash:3 coarse
sand).
MATERIAL
0773 Unslaked lime quintal 1.52 300.00 456.00
1980 Flyash cum 0.48 11.00 5.28
0982 Coarse sand (zone III) cum 0.72 1500.00 1080.00
2208 Carriage of Lime cum 0.24 163.93 39.34
2266 Carriage of Surkhi cum 0.48 163.93 78.69
2203 Carriage of Coarse sand cum 0.72 163.93 118.03
SUB HEAD : 16- ROAD WORK 1289
Code Description Unit Quantity Rate Amount
LABOUR
Labour for slaking the lime making,
lime putty, grinding, measuring,
carrying, depositing and mixing.
0114 Beldar day 0.90 645.00 580.50
0101 Bhisti day 0.45 714.00 321.30
9999 Running and upkeep of mortar mill L.S. 26.91 2.12 57.05
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 2764.85
Cost of 1.00 cum 2764.85
Say 2764.85
16.52Y Sub Analysis Y for Item Number 16.52
Code Description Unit Quantity Rate Amount
Sub Analysis 'Y' (16.52Y) for use in
Item No. 16.52
Details of cost for 1 cum. of cement
concrete
MATERIAL
Lime Flyash mortar
16.52X Rate as per sub analysis of Item
No 16.52X cum 0.40 2764.85 1105.94
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.64 1400.00 896.00
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.21 1350.00 283.50
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.85 163.93 139.34
LABOUR
0114 Beldar day 0.65 645.00 419.25
0115 Coolie day 0.60 645.00 387.00
0101 Bhisti day 0.27 714.00 192.78
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0128 Mate day 0.04 714.00 28.56
9999 Hire and running charges of mixer L.S. 26.91 2.12 57.05
9999 Sundries L.S. 13.52 2.12 28.66
9999 Hire charges of steel moulds, table
vibrators, rammers, bolts, nuts and
washers etc. L.S. 53.82 2.12 114.10
TOTAL 3727.08
Cost of 1.00 cum 3727.08
Say 3727.10
16.53 Providing and fixing concertina coil fencing with punched tape concertina coil
600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds
per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped
placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire,
stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary
bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-
SUB HEAD : 16- ROAD WORK 1290
in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of
high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478
gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
Code Description Unit Quantity Rate Amount
Details of cost for 30.00 m length
MATERIAL
8691 Punched tape concertina coil 600 mm
dia 10 m openable length (Total length
90 m) bundle 5.00 600.00 3000.00
(Having 50 Nos. of rounds per 6 meter
= 1 bundles)
Therefore, Nos. of bundles 30/10
=3bundles)
8692 RBT reinforced barbed wire metre 270.00 7.00 1890.00
9 rounds = 9x30 = 270m
8693 Turn buckle and strengthening bolt each set 10.00 42.00 420.00
9999 G.I. staples clips etc. L.S. 49.40 2.12 104.73
LABOUR
Labour for fixing straightening cutting
of tape/ coils & wire
0114 Beldar day 1.00 645.00 645.00
0.50x2 = 1.00 Nos (Taken double due
to height)
0102 Blacksmith 1st class day 0.50 784.00 392.00
0103 Blacksmith 2nd class day 0.50 714.00 357.00
TOTAL 6808.73 W
Add 1 % Water charges on “W” 68.09
TOTAL 6876.82 X
Add GST on “X” (multiplying
factor 0.1405) 966.19
TOTAL 7843.01 Y
Add 15% CPOH on “Y” 1176.45
TOTAL 9019.46 Z
Add Cess @ 1% on “Z” 90.19
cost for 30.00 metre 9109.65
cost per metre 303.66
Say 303.65
16.54 Providing and laying Dense Graded Bituminous Macadam using crushed stone
aggregates of specified grading, premixed with bituminous binder and filler,
transporting the hot mix to work site by tippers, laying with paver finisher equiped
with electronic sensor to the required grade, level and alignment and rolling with
smooth wheeled, vibratory and tandem rollers as per specifications to achieve
the desired compaction and density, complete as per specificatons and directions
of Engineer-in-Charge.
SUB HEAD : 16- ROAD WORK 1291
16.54.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5%
(percentage by weight of total mix) and lime filler @ 2% (percentage by weight of
Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 195 cum (or 450 M.T. )
MATERIAL
7309 Paving Asphalt VG-30 of approved
quality (percentage by weight of total
mix) tonne 22.50 38150.00 858375.00
2211 Carriage of Tar bitumen tonne 22.50 163.93 3688.43
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 22.50 tonnes
Weight of aggregate = 450 -22.50
= 427.50 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =427.50/1.5
=285cum
Grading - II/19 mm (Nominal Size)
25 - 10mm size = 30% of 285 = 85.5 cum
10 - 5mm size = 28% of 285 = 79.8 cum
5mm and below = 40% of 285 = 114 cum
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 42.75 1350.00 57712.50
Qty = 85.5 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.75 1350.00 57712.50
Qty = 85.5 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 39.90 1350.00 53865.00
Qty = 79.8 * 50 /100
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 39.90 1400.00 55860.00
Qty = 79.8 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 114.00 1400.00 159600.00
Qty = 285 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 279.30 163.93 45785.65
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 85.50 290.00 24795.00
2208 Carriage of Lime cum 6.63 163.93 1086.86
(consitering density of lime as 1.29
T per cum) V =8.55/1.29 = 6.63 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
SUB HEAD : 16- ROAD WORK 1292
Code Description Unit Quantity Rate Amount
0053 Tipper -5 Cum tonne/km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1459405.69 W
Add 1 % Water charges on "W" 14594.06
TOTAL 1473999.75 X
Add GST on "X" (multiplying
factor 0.1405) 207096.96
TOTAL 1681096.71 Y
Add 15% CPOH on "Y" 252164.51
TOTAL 1933261.22 Z
Add Cess @ 1% on "Z" 19332.61
Cost for 195 cum(450 M.T.) 1952593.83
Cost per cum. 10013.30
Say 10013.30
16.54.2 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5%
(percentage by weight of total mix) and lime filler @ 2% (percentage by weight of
Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 195 cum (or 450 M.T. )
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 22.50 38150.00 858375.00
(percentage by weight of total mix)
2211 Carriage of Tar bitumen tonne 22.50 163.93 3688.43
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 22.50 tonnes
Weight of aggregate = 450 -22.50
= 427.50 tonnes
Taking density of aggregate
= 1.5 tonne/cum
Volume of aggregate =427.50/1.5
=285cum
SUB HEAD : 16- ROAD WORK 1293
Code Description Unit Quantity Rate Amount
Grading - II/19 mm (Nominal Size)
25 - 10mm size = 30% of 285 = 85.5 cum
10 - 5mm size = 28% of 285 = 79.8 cum
5mm and below = 40% of 285 = 114 cum
0294 Stone Aggregate (Single size) :
25 mm nominal size cum 42.75 1350.00 57712.50
Qty = 85.5 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.75 1350.00 57712.50
Qty = 85.5 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 39.90 1350.00 53865.00
Qty = 79.8 * 50 /100
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 39.90 1400.00 55860.00
Qty = 79.8 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 114.00 1400.00 159600.00
Qty = 285 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 279.30 163.93 45785.65
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 85.50 290.00 24795.00
2208 Carriage of Lime cum 6.63 163.93 1086.86
(consitering density of lime as 1.29 T
per cum) V =8.55/1.29 = 6.63 cum
MACHINERY/ HIRE CHARGES:
0076 Drum Type HMP of 60-90 TPH capacity
@ 75 tonne per hour actual output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne/km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistancefor setting out lines, levels
and layout of construction
SUB HEAD : 16- ROAD WORK 1294
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1447405.69 W
Add 1 % Water charges on "W" 14474.06
TOTAL 1461879.75 X
Add GST on "X" (multiplying
factor 0.1405) 205394.10
TOTAL 1667273.85 Y
Add 15% CPOH on "Y" 250091.08
TOTAL 1917364.93 Z
Add Cess @ 1% on "Z" 19173.65
Cost for 195 cum(450 M.T.) 1936538.58
Cost per cum. 9930.97
Say 9930.95
16.55 Providing and laying bituminous macadam using crushed stone aggregates of
specified grading premixed with bituminous binder, transported to site by tippers,
laid over a previously prepared surface with paver finisher equiped with electronic
sensor to the required grade, level and alignment and rolling with smooth wheeled,
vibratory and tandem rollers as per specifications to achieve the desired compaction
and density, complete as per specificatons and directions of Engineer-in-Charge.
16.55.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50%
(percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-
120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 205 cum (or 450 M.T. )
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 15.75 38150.00 600862.50
3.5% of 450 MT = 15.75 MT
2211 Carriage of Tar bitumen tonne 15.75 163.93 2581.90
Weight of mix = 205 * 2.5 = 450 tonnes
Aggregate
Total weight of mix = 450 tonnes Weight of
bitumen = 15.75 tonnes Weight of
aggregate = 450 -15.75 = 434.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =434.25/1.5 =
289.50cum
Grading - II/19 mm (Nominal Size)
25 - 10mm size = 40% of 289.50
= 115.8 cum
10 - 5mm size = 40% of 289.50
= 115.8 cum
5mm and below = 20% of 289.50
= 57.9 cum
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
SUB HEAD : 16- ROAD WORK 1295
Code Description Unit Quantity Rate Amount
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 57.90 1400.00 81060.00
Qty = 115.8 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 57.90 1400.00 81060.00
Qty = 289.50 * 20 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 289.50 163.93 47457.74
MACHINERY
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
@75tonne per hour actual output
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
@75tonne per hour actual output
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
@75tonne per hour actual output
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne/km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading X *
10 / 100 = 13500.00 * 10 / 100 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1188441.89 W
Add 1 % Water charges on "W" 11884.42
TOTAL 1200326.31 X
Add GST on "X" (multiplying
factor 0.1405) 168645.85
TOTAL 1368972.16 Y
Add 15% CPOH on "Y" 205345.82
TOTAL 1574317.98 Z
Add Cess @ 1% on "Z" 15743.18
Cost for 205 cum(450 M.T.) 1590061.16
Cost per cum. 7756.40
Say 7756.40
SUB HEAD : 16- ROAD WORK 1296
16.55.2 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50%
(percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90
TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 205 cum (or 450 M.T. )
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 15.75 38150.00 600862.50
3.5% of 450 MT = 15.75 MT
2211 Carriage of Tar bitumen tonne 15.75 163.93 2581.90
Weight of mix = 205 * 2.5 = 450 tonnes
Aggregate
Total weight of mix = 450 tonnes Weight of
bitumen = 15.75 tonnes
Weight of aggregate = 450 -15.75 =
434.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =434.25/1.5
=289.50cum
Grading - II/19 mm (Nominal Size)
25 - 10mm size = 40% of 289.50
= 115.8 cum
10 - 5mm size = 40% of 289.50
= 115.8 cum
5mm and below = 20% of 289.50
= 57.9 cum
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 57.90 1350.00 78165.00
Qty = 115.8 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 57.90 1400.00 81060.00
Qty = 115.8 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 57.90 1400.00 81060.00
Qty = 289.50 * 20 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 289.50 163.93 47457.74
MACHINERY
0076 Drum Type HMP of 60-90 TPH
capacity @ 75 tonne per hour actual
output hour 6.00 12000.00 72000.00
@75tonne per hour actual output
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
@75tonne per hour actual output
0069 Generator 250 KVA hour 6.00 400.00 2400.00
SUB HEAD : 16- ROAD WORK 1297
Code Description Unit Quantity Rate Amount
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1176441.89 W
Add 1 % Water charges on "W" 11764.42
TOTAL 1188206.31 X
Add GST on "X" (multiplying
factor 0.1405) 166942.99
TOTAL 1355149.30 Y
Add 15% CPOH on "Y" 203272.39
TOTAL 1558421.69 Z
Add Cess @ 1% on "Z" 15584.22
Cost for 205 cum(450 M.T.) 1574005.91
Cost per cum. 7678.08
Say 7678.10
16.56 Providing and laying semi- dense Bituminous concrete using crushed stone
aggregates of specified grading, premixed with bituminous binder and filler,
transporting the hot mix to work site by tippers, laying with paver finisher equiped
with electronic sensor to the required grade, level and alignment and rolling with
smooth wheeled, vibratory and tandem rollers to achieve the desired compaction
and density as per specification, complete and as per directions of Engineer-in-Charge.
16.56.1 25 mm compacted thickness with bitumen of grade VG-30 @ 5% (percentage by
weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared
in Batch Type Hot Mix Plant of 100-120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 195 cum (450 tonnes)
Area covered for 25 mm thickness
=7800 sqm
SUB HEAD : 16- ROAD WORK 1298
Code Description Unit Quantity Rate Amount
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 22.50 38150.00 858375.00
5% of 450 MT = 22.50 MT
2211 Carriage of Tar bitumen tonne 22.50 163.93 3688.43
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 22.50 tonnes
Weight of aggregate = 450 -22.50 =
427.50 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =427.50/1.5
=285cum
Grading - II/19 mm (Nominal Size)
9.5 - 4.75 mm size = 57% of 285
= 162.45 cum
4.75mm and below = 41% of 285
= 116.85 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 81.225 1350.00 109653.75
Qty = 162.45 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 81.225 1350.00 109653.75
Qty = 162.45 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size nominal size cum 116.85 1400.00 163590.00
Qty = 285 * 41 /100
2202 Carriage of Stone aggregate below
40 mm nominal size nominal size cum 279.30 163.93 45785.65
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 85.50 290.00 24795.00
2208 Carriage of Lime cum 6.63 163.93 1086.86
(consitering density of lime as 1.29
T per cum) V =8.55/1.29 = 6.63 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
@75tonne per hour actual output
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
@75tonne per hour actual output
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
@75tonne per hour actual output
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket
capacity (incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken
10km avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
SUB HEAD : 16- ROAD WORK 1299
Code Description Unit Quantity Rate Amount
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction for checking
line & levels
TOTAL 1453983.19 W
Add 1 % Water charges on "W" 14539.83
TOTAL 1468523.02 X
Add GST on "X" (multiplying
factor 0.1405) 206327.48
TOTAL 1674850.51 Y
Add 15% CPOH on "Y" 251227.58
TOTAL 1926078.08 Z
Add Cess @ 1% on "Z" 19260.78
Cost for 7800 Sqm 1945338.86
Cost per sqm 249.40
Say 249.40
16.56.2 25 mm compacted thickness with bitumen of grade VG-30 @ 5% (percentage by
weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared
in Drum Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 195 cum (450 tonnes)
Area covered for 25 mm thickness
=7800 sqm
MATERIAL
7309 Paving Asphalt VG-30 of approved
quality tonne 22.50 38150.00 858375.00
5% of 450 MT = 22.50 MT
2211 Carriage of Tar bitumen tonne 22.50 163.93 3688.43
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 22.50 tonnes
Weight of aggregate = 450 -22.50 =
427.50 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =427.50/1.5
=285cum
Grading - II/19 mm (Nominal Size)
9.5 - 4.75 mm size = 57% of 285
= 162.45 cum
4.75mm and below = 41% of 285
= 116.85 cum
SUB HEAD : 16- ROAD WORK 1300
Code Description Unit Quantity Rate Amount
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 81.225 1350.00 109653.75
Qty = 162.45 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 81.225 1350.00 109653.75
Qty = 162.45 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 116.85 1400.00 163590.00
Qty = 285 * 41 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 279.30 163.93 45785.65
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 85.5 290.00 24795.00
2208 Carriage of Lime cum 6.63 163.93 1086.86
(consitering density of lime as 1.29 T
per cum) V =8.55/1.29 = 6.63 cum
MACHINERY/ HIRE CHARGES:
0076 Drum Type HMP of 60-90 TPH
capacity @ 75 tonne per hour actual
output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction for checking
line & levels
TOTAL 1441983.19 W
Add 1 % Water charges on "W" 14419.83
TOTAL 1456403.02 X
Add GST on "X" (multiplying
factor 0.1405) 204624.62
TOTAL 1661027.65 Y
Add 15% CPOH on "Y" 249154.15
TOTAL 1910181.79 Z
Add Cess @ 1% on "Z" 19101.82
Cost for 7800 Sqm 1929283.61
Cost per sqm 247.34
Say 247.35
SUB HEAD : 16- ROAD WORK 1301
16.57 Providing and laying Bituminous concrete using crushed stone aggregates of specified
grading, premixed with bituminous binder and filler, transporting the hot mix to work
site by tippers, laying with paver finisher equiped with electronic sensor to the required
grade, level and alignment and rolling with smooth wheeled, vibratory and tandem
rollers to achieve the desired compaction and density as per specification, complete
and as per directions of Engineer-in-Charge.
16.57.1 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by
weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared
in Batch Type Hot Mix Plant of 100-120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 24.75 38150.00 944212.50
@5.50% (percentage by weight of total
mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75 =
425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
SUB HEAD : 16- ROAD WORK 1302
Code Description Unit Quantity Rate Amount
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1551876.05 W
Add 1 % Water charges on "W" 15518.76
TOTAL 1567394.81 X
Add GST on "X" (multiplying
factor 0.1405) 220218.97
TOTAL 1787613.78 Y
Add 15% CPOH on "Y" 268142.07
TOTAL 2055755.84 Z
Add Cess @ 1% on "Z" 20557.56
Cost for 191 cum(450 Tonne) 2076313.40
Cost per cum. 10870.75
Say 10870.75
SUB HEAD : 16- ROAD WORK 1303
16.57.2 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by
weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and
waste plastic additive @ 8% (percentage by weight of bitumen) prepared in Batch
Type Hot Mix Plant of 100- 120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 24.75 38150.00 944212.50
@5.50% (percentage by weight of total mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75 =
425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
=119.07 cum
Waste Plastic @ 8% of the weigh of
bitumen i.e. 24.75*8%
7280 Waste plastic additive tonne 1.98 38100.00 75438.00
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
SUB HEAD : 16- ROAD WORK 1304
Code Description Unit Quantity Rate Amount
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1627314.05 W
Add 1 % Water charges on "W" 16273.14
TOTAL 1643587.19 X
Add GST on "X" (multiplying
factor 0.1405) 230924.00
TOTAL 1874511.19 Y
Add 15% CPOH on "Y" 281176.68
TOTAL 2155687.86 Z
Add Cess @ 1% on "Z" 21556.88
Cost for 191 cum(450 Tonne) 2177244.74
Cost per cum. 11399.19
Say 11399.20
16.57.3 40/50 mm compacted thickness with bitumen of grade PMB-40 @ 5.5% (percentage
by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate)
prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
0312 Bitumen grade PMB - 40 M.T. 24.75 32950.00 815512.50
@5.50% (percentage by weight of
total mix
SUB HEAD : 16- ROAD WORK 1305
Code Description Unit Quantity Rate Amount
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75 =
425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) : 12.5 mm
nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken
10km avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
SUB HEAD : 16- ROAD WORK 1306
Code Description Unit Quantity Rate Amount
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1423176.05 W
Add 1 % Water charges on "W" 14231.76
TOTAL 1437407.81 X
Add GST on "X" (multiplying
factor 0.1405) 201955.80
TOTAL 1639363.60 Y
Add 15% CPOH on "Y" 245904.54
TOTAL 1885268.14 Z
Add Cess @ 1% on "Z" 18852.68
Cost for 191 cum(450 Tonne) 1904120.82
Cost per cum. 9969.22
Say 9969.20
16.57.4 40/50 mm compacted thickness with bitumen of grade CRMB-60 @ 5.5% (percentage
by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate)
prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7741 Modified Bitumen Refinary produced
CRMB - 60 tonne 24.75 29150.00 721462.50
@5.50% (percentage by weight of
total mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75 =
425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
SUB HEAD : 16- ROAD WORK 1307
Code Description Unit Quantity Rate Amount
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0062 Hot mix Plant -120 TPH capacity hour 3.00 15000.00 45000.00
0063 Hot mix Plant 100 TPH Capacity hour 3.00 13000.00 39000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
SUB HEAD : 16- ROAD WORK 1308
Code Description Unit Quantity Rate Amount
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1329126.05 W
Add 1 % Water charges on "W" 13291.26
TOTAL 1342417.31 X
Add GST on "X" (multiplying
factor 0.1405) 188609.63
TOTAL 1531026.94 Y
Add 15% CPOH on "Y" 229654.04
TOTAL 1760680.98 Z
Add Cess @ 1% on "Z" 17606.81
Cost for 191 cum(450 Tonne) 1778287.79
Cost per cum. 9310.41
Say 9310.40
16.57.5 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by
weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared
in drum Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 24.75 38150.00 944212.50
@5.50% (percentage by weight of
total mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75
= 425.25 tonnes
Taking density of aggregate
= 1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
SUB HEAD : 16- ROAD WORK 1309
Code Description Unit Quantity Rate Amount
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0076 Drum Type HMP of 60-90 TPH capacity
@ 75 tonne per hour actual output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1539876.05 W
Add 1 % Water charges on "W" 15398.76
TOTAL 1555274.81 X
Add GST on "X" (multiplying
factor 0.1405) 218516.11
TOTAL 1773790.92 Y
Add 15% CPOH on "Y" 266068.64
TOTAL 2039859.55 Z
Add Cess @ 1% on "Z" 20398.60
Cost for 191 cum(450 Tonne) 2060258.15
Cost per cum. 10786.69
Say 10786.70
SUB HEAD : 16- ROAD WORK 1310
16.57.6 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by
weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and
waste plastic additive @ 8% (percentage by weight of bitumen) prepared in drum
Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7309 Paving Asphalt VG-30 of approved quality tonne 24.75 38150.00 944212.50
@5.50% (percentage by weight of
total mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Waste Plastic @ 8% of the weigh of
bitumen i.e. 24.75*8%
7280 Waste plastic additive tonne 1.98 38100.00 75438.00
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75 =
425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
SUB HEAD : 16- ROAD WORK 1311
Code Description Unit Quantity Rate Amount
0076 Drum Type HMP of 60-90 TPH capacity
@ 75 tonne per hour actual output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1615314.05 W
Add 1 % Water charges on "W" 16153.14
TOTAL 1631467.19 X
Add GST on "X" (multiplying
factor 0.1405) 229221.14
TOTAL 1860688.33 Y
Add 15% CPOH on "Y" 279103.25
TOTAL 2139791.57 Z
Add Cess @ 1% on "Z" 21397.92
Cost for 191 cum(450 Tonne) 2161189.49
Cost per cum. 11315.13
Say 11315.15
16.57.7 40/50 mm compacted thickness with bitumen of grade PMB-40 @ 5.5% (percentage
by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate)
prepared in drum Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
0312 Bitumen grade PMB - 40 M.T. 24.75 32950.00 815512.50
@5.50% (percentage by weight of
total mix
SUB HEAD : 16- ROAD WORK 1312
Code Description Unit Quantity Rate Amount
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75
= 425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
=283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
= 119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) :
06 mm nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by
weight of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29 T
per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0076 Drum Type HMP of 60-90 TPH capacity
@ 75 tonne per hour actual output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
SUB HEAD : 16- ROAD WORK 1313
Code Description Unit Quantity Rate Amount
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1411176.05 W
Add 1 % Water charges on "W" 14111.76
TOTAL 1425287.81 X
Add GST on "X" (multiplying
factor 0.1405) 200252.94
TOTAL 1625540.74 Y
Add 15% CPOH on "Y" 243831.11
TOTAL 1869371.85 Z
Add Cess @ 1% on "Z" 18693.72
Cost for 191 cum(450 Tonne) 1888065.57
Cost per cum. 9885.16
Say 9885.15
16.57.8 40/50 mm compacted thickness with bitumen of grade CRMB-60 @ 5.5% (percentage
by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate)
prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.
Code Description Unit Quantity Rate Amount
Details of cost for 191 cum (450 tonnes)
MATERIAL
7741 Modified Bitumen Refinary produced
CRMB - 60 tonne 24.75 29150.00 721462.50
@5.50% (percentage by weight of
total mix
2211 Carriage of Tar bitumen tonne 24.75 163.93 4057.27
Aggregate
Total weight of mix = 450 tonnes
Weight of bitumen = 24.75 tonnes
Weight of aggregate = 450 -24.75
= 425.25 tonnes
Taking density of aggregate =
1.5 tonne/cum
Volume of aggregate =425.25/1.5
= 283.50cum
Grading - II/19 mm (Nominal Size)
13.2 - 10mm size = 30% of 283.50
= 85.05 cum
SUB HEAD : 16- ROAD WORK 1314
Code Description Unit Quantity Rate Amount
10 - 5mm size = 25% of 283.50
= 70.88 cum
5mm and below = 42% of 283.50
=119.07 cum
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 42.525 1350.00 57408.75
Qty = 85.05 * 50 /100
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 35.44 1350.00 47844.00
Qty = 70.88 * 50 /100
0298 Stone Aggregate (Single size) : 06 mm
nominal size cum 35.44 1400.00 49616.00
Qty = 70.88 * 50 /100
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 119.07 1400.00 166698.00
Qty = 283.5 * 40 /100
2202 Carriage of Stone aggregate below
40 mm nominal size cum 275.00 163.93 45080.75
Lime Filler @ 2% ( percentage by weight
of aggregate)
0777 Dry hydrated lime (factory made) quintal 127.60 290.00 37004.00
2208 Carriage of Lime cum 9.89 163.93 1621.27
(consitering density of lime as 1.29
T per cum) V = 12.758/1.29 = 9.89 cum
MACHINERY/ HIRE CHARGES:
0076 Drum Type HMP of 60-90 TPH capacity
@ 75 tonne per hour actual output hour 6.00 12000.00 72000.00
0064 Paver finisher Hydrostatic with sensor
control 100 TPH hour 6.00 1500.00 9000.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Topper 10 tonne capacity (Taken 10km
avarage lead)
450x10=4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0055 Smooth Wheeled Roller 8 to 10 tonne hour 3.90 300.00 1170.00
for initial break down rolling.(6*0.65)
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
for intermediate rolling.(6*0.65)
0056 Tandem Road Roller hour 3.90 1200.00 4680.00
Finish rolling with 6-8 tonnes smooth
wheeled tandem roller.(6*0.65)
LABOUR
0128 Mate day 0.84 714.00 599.76
0114 Beldar day 14.00 645.00 9030.00
working with HMP, mechanical broom,
paver, roller, asphalt cutter and
assistance for setting out lines, levels
and layout of construction
SUB HEAD : 16- ROAD WORK 1315
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar (for floor rubbing etc.) day 5.00 714.00 3570.00
for checking line & levels
TOTAL 1317126.05 W
Add 1 % Water charges on "W" 13171.26
TOTAL 1330297.31 X
Add GST on "X" (multiplying
factor 0.1405) 186906.77
TOTAL 1517204.08 Y
Add 15% CPOH on "Y" 227580.61
TOTAL 1744784.69 Z
Add Cess @ 1% on "Z" 17447.85
Cost for 191 cum(450 Tonne) 1762232.54
Cost per cum. 9226.35
Say 9226.35
16.59 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm
thick aluminium sheet, face to be fully covered with high intensity encapsulated type
heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in
blue and silver white or other colour combination including subject matter, message
(bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an
adhesive backing which shall be activated by applying heat and pressure conforming
to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium
alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm
along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of
size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm
welded with base plate of size 100x100x5 mm at the bottom end and including making
holes in pipes, angles flats, providing & fixing M.S. message plate of required size,
steel work to be painted with two or more coats of synthetic enamel paint of required
shade and of approved brand & manufacture over priming coat of zinc chromate
yellow primer (vertical MS-Tee support to be painted in black and white
colours).Backside of aluminium sheet to be painted with two or more coats of epoxy
paint over and including appropriate priming coat including all leads and lifts etc.
complete as per drawing , specification and direction of Engineer-in-charge.
16.59.1 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of
3750 mm
Code Description Unit Quantity Rate Amount
Details cost for 1 no. of 0.636 sqm
MATERIAL
Aluminium sheet 2 mm thick
3.14/4x(0.9)x(0.9)=0.636 sqm
add 10% wastage = 0.064 i.e. 0.700sqm
@ 5.60kg/ sqm = 3.92kg
2704 Aluminium Strip 40 mm wide and 2 mm
thick kilogram 3.92 240.00 940.80
2302 Carriage of G.I. sheet and accessories tonne 0.00392 145.72 0.57
3.92kg or 0.00392 MT
High intensity retro reflective sheet
= 0.70 sqm.
High intensity sheet for lettering / sign
and border etc.
SUB HEAD : 16- ROAD WORK 1316
Code Description Unit Quantity Rate Amount
Taking 40% Area =0.28sqm,total
= 0.70 + 0.28 = 0.98 sqm
8690 High intensity retro - reflective sheet sqm 0.98 1443.00 1414.14
Steel work
Supporting frame 25x25x3mm for 900mm
dia board:-
3.14D=3.1416x0.90=2.83 metre
@ 1.10kg/m
Angle iron 35x35x.5mm for fixing the
support frame with vertical Tee-iron
support post
2x0.05=0.10m @ 2.6 kg/m = 0.26kg
Vertical post of M.S. tee of section
ISNT 50x50x6mm = 3.75 metre
@ 4.50kg/m = 16.88 kg
Bass plate to be welded at bottom end of
tee (As hold fast)
(100x100x5mm)x7850/133)=0.39kg, total
= 3.11 + 0.26 +16.88 + 0.39 =
Add wastage @ 5% = 1.03
Total = 20.64 + 1.03 = 21.67kg.
10.2 Rate as per item no 10.2 of
SH : Steel work kg 21.67 78.20 1694.59 A
LABOUR
0128 Mate day 0.01 714.00 7.14
0114 Beldar day 0.25 645.00 161.25
9999 Cost of material for drilling holes,
nut bolts & rivets, fabrication etc. L.S. 65.00 2.12 137.80
Painting with synthetic enamel paint
on steel work
support frame 25x25x3mm
=2.83x0.10=0.283 sqm
Fixing angle 35x35x5mm
= 2x0.50x0.14=0.014 sqm
Vertical post Tee 50x50x6mm
=3.75x0.20=0.750sqm
Base plate 100x100x5mm
Surface area = 2x[0.10x0.10] =0.02
4x0.10x0.005 = 0.002
Total = 1.069 sqm
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.07 131.45 140.65 A
Painting with epoxy paint on back side
of aluminium sheet.
13.52.1 Rate as per Item no. 13.52.1 of
SH: Finishing sqm 0.636 201.70 128.28 A
9999 Sundries and hold fast etc. L.S. 78.00 2.12 165.36
TOTAL 4790.59 W
Add 1 % Water charges on "W-A" 28.27
TOTAL 4818.86 X
Add GST on "X-A" (multiplying
factor 0.1405) 401.17
TOTAL 5220.03 Y
Add 15% CPOH on "Y-A" 488.48
TOTAL 5708.51 Z
Add Cess @ 1% on "Z-A" 37.45
Cost of 1 no. 5745.96
Say 5745.95
SUB HEAD : 16- ROAD WORK 1317
16.59.2 Cautionary /warning sign boards of equilateral triangular shape having each side of
900 mm with support length of 3650 mm
Code Description Unit Quantity Rate Amount
Details cost for 1 board of 0.35 sqm
MATERIAL
Aluminium sheet 2 mm thick
Area 1/2x(0.9)x(0.78)=0.35 sqm
add 10% wastage = 0.04 i.e. 0.39sqm @
5.60kg/ sqm = 2.18kg
2704 Aluminium Strip 40 mm wide and 2 mm
thick kilogram 2.18 240.00 523.20
2302 Carriage of G.I. sheet and accessories tonne 0.00218 145.72 0.32
2.18kg or 0.00218 MT
High intensity retro reflective sheet
= 0.39 sqm.
High intensity sheet for lettering / sign/
symbol/ border etc.
Taking 40% Area =0.16sqm,
total = 0.39 + 0.16 = 0.55 sqm
8690 High intensity retro - reflective sheet sqm 0.55 1443.00 793.65
Steel work
Angle iron frame 25x25x3mm 3x0.90
= 2.70 metre
@ 1.10kg/m
Angle iron 35x35x.5mm for fixing the
support frame to Tee- iron support post
2x0.05=0.10m @ 2.6 kg/m = 0.26kg
Vertical post of M.S. tee of section
ISNT 50x50x6mm = 1x3.65=3.65m @
4.50kg/m =16.43kg
Bass plate 100x100x5mm connected to
bottom end of vertocal tee.
(0.10x0.10x0.005x7850kg =0.39kg,
total = 2.97+ 0.26 + 16.43 + 0.39
= 20.05kg.
Add wastage @ 5% = 1.00,
total = 20.05 + 1.00 = 21.05kg
10.2 Rate as per item no 10.2 of
SH : Steel work kg 21.05 78.20 1646.11 A
LABOUR
0128 Mate day 0.01 714.00 7.14
0114 Beldar day 0.25 645.00 161.25
9999 Cost of material for drilling holes,
nut bolts & rivets, fabrication etc. L.S. 65.00 2.12 137.80
Painting with synthetic enamel paint on
Angle iron .
support frame 25x25x3mm
=1x2.7x0.10=0.27 sqm.
Angle 35x35x5mm
= 2x0.50x0.14=0.014 sqm
Tee 50x50x6mm
=1x3.65x0.20 =0.73sqm
Base plate to be welded at bottom end of
Tee 100x100x5mm
0.022 sqm
Total = 1.036 sqm
SUB HEAD : 16- ROAD WORK 1318
Code Description Unit Quantity Rate Amount
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.036 131.45 136.18 A
Painting with epoxy paint on back side
of aluminium sheet. 0.35 sqm
13.52.1 Rate as per Item no. 13.52.1 of
SH: Finishing sqm 0.35 201.70 70.60 A
9999 Sundries & hold fast etc. L.S. 65.00 2.12 137.80
TOTAL 3614.04 W
Add 1 % Water charges on "W-A" 17.61
TOTAL 3631.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 249.92
TOTAL 3881.57 Y
Add 15% CPOH on "Y-A" 304.30
TOTAL 4185.88 Z
Add Cess @ 1% on "Z-A" 23.33
Cost of 1 board. 4209.21
Say 4209.20
16.60 Manufacturing, supplying and fixing retro reflective overhead signage boards made
up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and
encapsulated lens type heat activated retro reflective sheeting conforming to type -
III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per
IRC : 67-2001 in silver white with blue colour back ground and with high intensity
grade, pasted on substrate by pressure sensitive adhesive backing which shall be
activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing
the same to the plate of structural frame work by means of suitable sized aluminium
alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as
well as in two vertical rows along with theft resistant measures, including the cost of
painting with two or more coats of epoxy paint in grey colour on the back side of
aluminium sheet including appropriate priming coat. The rate includes the cost of
rounding off the corners, lowering down the structural frame work from the gantry,
fixing and erecting the same in position all complete as per drawings, specification
and direction of the engineer-in-charge.(Structural frame work including M.S. plate
to be provided separately. Rectangular area of the sheet only shall be measured for
payment).
16.60.1 Overhead informatory road signage
Code Description Unit Quantity Rate Amount
Details of cost for boards area
3.00x1.20 =3.60 sqm
MATERIAL
2704 Aluminium Strip 40 mm wide and
2 mm thick kilogram 21.17 240.00 5080.80
Add 5% wastage = 1.01 kg
Total = 20.16 + 1.01 = 21.17 kg.
2302 Carriage of G.I. sheet and accessories tonne 0.02117 145.72 3.08
high intensity sheet for written matter.
Taking 40% 3.60x40% = 1.44 sqm.
Total = 3.60 + 1.44 = 5.04 sqm.
SUB HEAD : 16- ROAD WORK 1319
Code Description Unit Quantity Rate Amount
8690 High intensity retro - reflective sheet sqm 5.04 1443.00 7272.72
0588 Chromium plated Brass screws 25 mm 100 Nos 0.34 180.00 61.20
for peripheries = 2x(300+120)/30=28 nos.
For vertical Rows = 2x (120/30-2)=4 nos.
Total= 28 + 4 = 32nos.
For wastage @ 5% =2 nos.
Total = 32 +2 = 34 nos.
Labour charges for drilling holes
9999 Hire charges of drill machine and sundries L.S. 52.00 2.12 110.24
9999 Hoisting board L.S. 390.00 2.12 826.80
Labour charges for manufacturing of
board including .
9999 fixing retro reflective sheet L.S. 564.20 2.12 1196.10
Painting with epoxy paint on back side
of Aluminium sheet,
13.52.1 Rate as per Item no. 13.52.1 of
SH: Finishing sqm 3.60 201.70 726.12 A
TOTAL 15277.07 W
Add 1 % Water charges on "W-A" 145.51
TOTAL 15422.58 X
Add GST on "X-A" (multiplying
factor 0.1405) 2064.85
TOTAL 17487.43 Y
Add 15% CPOH on "Y-A" 2514.20
TOTAL 20001.63 Z
Add Cess @ 1% on "Z-A" 192.76
Cost of 3.60 sqm 20194.38
Cost of 1 sqm. 5609.55
Say 5609.55
16.61 Providing Retro-reflective regulatory sign board of size 900 mm dia meter made
out of 2 mm thick aluminium sheet, face to be fully covered with high intensity
encapsulated lens type retro -reflective sheeting as approved by Engineer-in-
charge. Letter, symbols, borders etc. will be as per IRC - 67 with required colour
scheme on the boards and with the high intensity grade A. The aluminium sheet
to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be
fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long
welded to the frame with adequate anti-theft arrangement .Sheet work to be
painted with two or more coats of synthetic enamel paint over an under coat
(primer) and back side of aluminium sheet to be painted with two or more coats
of epoxy paint including appropriate priming coat complete in all respects as
per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details cost for one board of 0.635 sqm
Aluminium sheet 2mm thick = 0.635 sqm.
Add 10% wastage = 0.06 sqm, total =
0.635 + 0.06 = 0.695 sqm.
Say 0.70 sqm @ 5.6kg/sqm = 3.98 kg
SUB HEAD : 16- ROAD WORK 1320
Code Description Unit Quantity Rate Amount
MATERIAL
2704 Aluminium Strip 40 mm wide and 2 mm
thick kilogram 3.98 240.00 955.20
High intensity retro reflective sheet
= 0.70 sqm
high intensity sheet for lettering/ sing
and border etc.
Taking 40% Area=0.28 sqm, total
= 0.70 + 0.28 = 0.98 sqm.
8690 High intensity retro - reflective sheet sqm 0.98 1443.00 1414.14
Angle iron 40x40x4mm = 4x0.60=2.40@
2.4kg/ mtr = 5.76 kg
50x50x5 mm = 2x4m =8m @ 3kg/ mtr
=24.00 kg
Total = 5.76 + 24.00 = 29.76 kg
10.2 Rate as per item no 10.2 of
SH : Steel work kg 29.76 78.20 2327.23 A
LABOUR
0128 Mate day 0.01 714.00 7.14
0114 Beldar day 0.25 645.00 161.25
9999 Cost of material for drilling holes,
nut bolts & rivets, facrication etc. L.S. 70.23 2.12 148.89
(e) Painting with synthetic enamel paint
1x2.40.12=0.29 sqm
1x4.00x0.12=0.80 sqm,
Total = 0.29 + 0.80 = 1.09 sqm
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.09 131.45 143.28 A
13.52.1 Painting with epoxy paint on back side
of aluminium sheet, Rate as per Item
no. 13.52.1 of SH: Finishing sqm 0.635 201.70 128.08 A
9999 Sundries & hole fast etc, L.S. 31.20 2.12 66.14
TOTAL 5351.35 W
Add 1 % Water charges on "W-A" 27.53
TOTAL 5378.88 X
Add GST on "X-A" (multiplying
factor 0.1405) 390.63
TOTAL 5769.51 Y
Add 15% CPOH on "Y-A" 475.64
TOTAL 6245.15 Z
Add Cess @ 1% on "Z-A" 36.47
Cost for 1 board 6281.62
Say 6281.60
SUB HEAD : 16- ROAD WORK 1321
16.62 Providing and applying 2.5 mm thick road marking strips (retro- reflective) of
specified shade/ colour using hot thermoplastic material by fully/ semi automatic
thermoplastic paint applicator machine fitted with profile shoe, glass beads
dispenser, propane tank heater and profile shoe heater, driven by experienced
operator on road surface including cost of material, labour, T&P, cleaning the
road surface of all dirt, seals, oil, grease and foreign material etc. complete as
per direction of Engineer-in-charge and accordance with applicable
specifications.
Code Description Unit Quantity Rate Amount
Details of cost for 200 sqm (Area
covered on one day):-
MATERIAL
Thermoplastic paint screeded in paint
form for 2.5 mm thick road making
stripe including glass beads etc. as per
specifications
200 sqm @ 5kg/ sqm = 1000 kg
Wastage @ 5% = 50kg
Total = 1050 kg
8687 Thermoplastic paint kg 1050.00 66.00 69300.00
Glass beads (B-class) to be sprayed
over the paint stripe @ 250 gms. Per
sqm = 100x0.25=25 kg
8688 Glass beads kg 50.00 72.00 3600.00
MACHINERY
0033 Paint applicator. day 1.00 800.00 800.00
0083 Hire charges of TATA 407 or equivalent
for local shifting. day 1.00 1400.00 1400.00
1241 Commercial LPG in cylinder. kg 142.00 84.00 11928.00
LABOUR
0157 Operator (Pile/ Special machine) day 1.00 784.00 784.00
0139 Skilled Beldar (for floor rubbing etc.) day 4.00 714.00 2856.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 93248.00 W
Add 1 % Water charges on “W” 932.48
TOTAL 94180.48 X
Add GST on “X” (multiplying
factor 0.1405) 13232.36
TOTAL 107412.84 Y
Add 15% CPOH on “Y” 16111.93
TOTAL 123524.76 Z
Add Cess @ 1% on “Z” 1235.25
Cost for 200 sqm 124760.01
Cost per sqm 623.80
Say 623.80
SUB HEAD : 16- ROAD WORK 1322
16.63 Providing, laying and making kerb channel 30 cm wide and 50 mm thick with
cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20
mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well
rammed and consolidated and grouted with fine sand, including finishing the
top smooth etc. complete and as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
METERIAL
0287 Brick Aggregate (Single size) : 40 mm
nominal size cum 1.00 650.00 650.00
2260 Carriage of Brick aggregate cum 1.00 178.19 178.19
6501 Sand zone V (Jamuna) cum 0.08 1300.00 104.00
2335 Carriage of Jamuna sand cum 0.08 163.93 13.11
Labour for spreading, ramming and
consolidation.
0114 Beldar day 0.35 645.00 225.75
0115 Coolie day 0.26 645.00 167.70
0101 Bhisti day 0.18 714.00 128.52
Cement concrete-1:3:6
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete
Work cum 0.50 6670.25 3335.13 A
TOTAL 4802.40 W
Add 1 % Water charges on "W-A" 14.67
TOTAL 4817.07 X
Add GST on "X-A" (multiplying
factor 0.1405) 208.21
TOTAL 5025.29 Y
Add 15% CPOH on "Y-A" 253.52
TOTAL 5278.81 Z
Add Cess @ 1% on "Z-A" 19.44
Cost for 10 sqm. 5298.25
Cost for 1 sqm. 529.82
Say 529.80
16.64 Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40
mm thick nominal size including spreading, well ramming, consolidating and
grouting with jamuna sand, including finishing smooth etc. complete as per
direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
METERIAL
0287 Brick Aggregate (Single size) :
40 mm nominal size cum 1.00 650.00 650.00
2260 Carriage of Brick aggregate cum 1.00 178.19 178.19
6501 Sand zone V (Jamuna) cum 0.08 1300.00 104.00
2335 Carriage of Jamuna sand cum 0.08 163.93 13.11
Labour for spreading, ramming and
consolidation.
0114 Beldar day 0.35 645.00 225.75
0115 Coolie day 0.26 645.00 167.70
SUB HEAD : 16- ROAD WORK 1323
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.18 714.00 128.52
TOTAL 1467.27 W
Add 1 % Water charges on “W” 14.67
TOTAL 1481.95 X
Add GST on “X” (multiplying
factor 0.1405) 208.21
TOTAL 1690.16 Y
Add 15% CPOH on “Y” 253.52
TOTAL 1943.68 Z
Add Cess @ 1% on “Z” 19.44
Cost for 10 sqm. 1963.12
Cost for 1 sqm. 196.31
Say 196.30
16.65 Providing and fixing post delineators made of ABS round body fitted with 2 nos
100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia
duly powder coated anti-rust and anti theft steel to be installed as per direction
of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8685 Delineator each 1.00 336.00 336.00
9999 Fixing materials. L.S. 78.00 2.12 165.36
9999 Fixing charges. L.S. 39.00 2.12 82.68
TOTAL 584.04 W
Add 1 % Water charges on "W" 5.84
TOTAL 589.88 X
Add GST on "X" (multiplying
factor 0.1405) 82.88
TOTAL 672.76 Y
Add 15% CPOH on "Y" 100.91
TOTAL 773.67 Z
Add Cess @ 1% on "Z" 7.74
Cost of 1 no. 781.41
Say 781.40
16.66 Excavating holes upto 0.10 cum, including getting out the excavated soil, then
returning the soil as deported in layers not exceeding 20 cm in depth, including
consolidating and deposited layer by ramming watering etc., disposing of
surplus excavated soil as directed with in a lead of 50 mm and lift upto 1.5 m.
16.66.1 All kind of soil
Code Description Unit Quantity Rate Amount
Details of cost for 30 holes-
Earth work 30x0.10 = 3.0 cum.
Extra labour for filling and ramming
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 3.00 286.85 860.55 A
SUB HEAD : 16- ROAD WORK 1324
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 889.21 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 889.50 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 893.57 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 898.52 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 30 holes 898.90
Cost of 1 hole 29.96
Say 29.95
16.67 Providing and fixing at or near ground level factory made RCC pavement slab
of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia
M.S. bars 4 nos on each side, including setting in position in footpath to the
required level and line over a bed of 20 mm average thick cement mortar 1:5 (1
cement : 5 coarse sand), having joint thickness not more than 5mm except on
curve, including filling of joints with same cement mortar and making grooves
etc. complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL
8694 Precast pavement slab 450 x 450 x
50 mm (M - 30) each 48.00 145.00 6960.00
9977 Carriage of slab. L.S. 52.00 2.12 110.24
20mm (bed and joints) CM.
1:5 (1 cement: 5 coarse sand)
3.10 Rate as per Item Number 3.10 of
SH: Mortars cum 0.25 3995.00 998.75
LABOUR
0155 Mason (average) day 1.10 749.00 823.90
0100 Bandhani day 1.10 714.00 785.40
0114 Beldar day 0.55 645.00 354.75
0101 Bhisti day 0.27 714.00 192.78
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 10248.69 W
Add 1 % Water charges on "W" 102.49
TOTAL 10351.18 X
Add GST on "X" (multiplying
factor 0.1405) 1454.34
TOTAL 11805.52 Y
Add 15% CPOH on "Y" 1770.83
TOTAL 13576.35 Z
Add Cess @ 1% on "Z" 135.76
Cost for 10 sqm. 13712.11
Cost for 1 sqm 1371.21
Say 1371.20
SUB HEAD : 16- ROAD WORK 1325
16.68 Providing and laying 60mm thick faciory made cement concrete interlocking
paver block of M -30 grade made by block making machine with strong vibratory
compaction, of approved size, design & shape, laid in required colour and pattern
over and including 50mm thick compacted bed of coarse sand, filling the joints
with line sand etc. all complete as per the direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm
MATERIAL
8689 Interlocking C.C. paver block
( 60 mm thick, M-30) sqm 10.00 440.00 4400.00
Bedding layer - 50mm thick
0982 Coarse sand (zone III) cum 0.50 1500.00 750.00
=10x0.050=0.50 cum
2203 Carriage of Coarse sand cum 0.50 163.93 81.97
0983 Fine sand (zone IV) cum 0.15 900.00 135.00
2203 Carriage of fine sand cum 0.15 163.93 24.59
Laying charges (Bassed on actual
observation)
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 0.50 645.00 322.50
TOTAL 7108.05 W
Add 1 % Water charges on "W" 71.08
TOTAL 7179.14 X
Add GST on "X" (multiplying
factor 0.1405) 1008.67
TOTAL 8187.80 Y
Add 15% CPOH on "Y" 1228.17
TOTAL 9415.97 Z
Add Cess @ 1% on "Z" 94.16
Cost for 10.00 sqm 9510.13
Cost for 1.00 sqm. 951.01
Say 951.00
16.69 Providing and laying at or near ground level factory made kerb stone of M-25
grade cement concrete in position to the required line, level and curvature,
jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making
joints with or without grooves (thickness of joints except at sharp curve shall
not to more than 5mm), including making drainage opening wherever required
complete etc. as per direction of Engineer-in-charge (length of finished kerb
edging shall be measured for payment). (Precast C.C. kerb stone shall be
approved by Engineer-in-charge).
Code Description Unit Quantity Rate Amount
Details of cost 100 metre i.e.
100x0.375x0.20=7.50 cum.
No. of kerb stones = 100/0.405=247 Nos
Precast C.C. Kerb stone M - 25 =
247x0.40x0.375x0.20=7.41 cum
SUB HEAD : 16- ROAD WORK 1326
Code Description Unit Quantity Rate Amount
METERIAL
8686 Precast C.C. Kerb stone M - 25 cum 7.41 5600.00 41496.00
Mortar 1:3 for fixing joints =
246x1x[(0.115+0.20)/2] x 0.375x0.005
= 0.073 cum.
Cement mortar 1:3 (1 cement :
3 coarse sand)
3.8 Rate as per Item Number 3.8 of
SH: Mortars cum 0.073 5024.15 366.76
Labour for fixing of kerb stones
0123 Mason (brick layer) 1st class day 2.50 784.00 1960.00
0124 Mason (brick layer) 2nd class day 2.50 714.00 1785.00
0114 Beldar day 2.50 645.00 1612.50
0115 Coolie day 1.65 645.00 1064.25
TOTAL 48284.51 W
Add 1 % Water charges on "W" 482.85
TOTAL 48767.36 X
Add GST on "X" (multiplying
factor 0.1405) 6851.81
TOTAL 55619.17 Y
Add 15% CPOH on "Y" 8342.88
TOTAL 63962.05 Z
Add Cess @ 1% on "Z" 639.62
Cost of 7.50 cum 64601.67
cost for 1 cum. 8613.56
Say 8613.55
16.70 Providing and fixing G.I. chain link fabric fencing of required width in mesh size
50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers
as required complete as per the direction of Engineer-in-charge.
16.70.1 Made of G.I. wire of dia 4 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
G.I. chain link 50x50 mm mesh
= 10.00 sqm.
Wastage @ 5% = 0.50 sqm.
Total = 10.50 sqm.
8695 Chain link fabric fencing mesh of size
50x50 mm made of G.I. wire of dia 4 mm sqm 10.50 300.00 3150.00
9977 Carriage. L.S. 156.00 2.12 330.72
LABOUR
0103 Blacksmith 2nd class day 2.14 714.00 1527.96
0114 Beldar day 1.62 645.00 1044.90
SUB HEAD : 16- ROAD WORK 1327
Code Description Unit Quantity Rate Amount
9999 Sundries including G.I. wire, nuts and
bolts and warshers. L.S. 174.75 2.12 370.47
TOTAL 6424.05 W
Add 1 % Water charges on "W" 64.24
TOTAL 6488.29 X
Add GST on "X" (multiplying
factor 0.1405) 911.60
TOTAL 7399.90 Y
Add 15% CPOH on "Y" 1109.98
TOTAL 8509.88 Z
Add Cess @ 1% on "Z" 85.10
Cost for 10 sqm. 8594.98
Cost for 1 sqm. 859.50
Say 859.50
16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than
5 mm in required colour and shade
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
G.I. chain link 50x50 mm mesh
PVC coated = 10.00 sqm.
Wastage @ 5% = 0.50 sqm.
Total = 10.50 sqm.
8696 Chain link fabric fencing mesh of size
50x50 mm made of G.I. wire of dia
4 mm, PVC coated to outer dia 5 mm sqm 10.50 330.00 3465.00
9977 Carriage. L.S. 156.00 2.12 330.72
LABOUR
0103 Blacksmith 2nd class day 2.14 714.00 1527.96
0114 Beldar day 1.62 645.00 1044.90
9999 Sundries including G.I. wire, nuts and
bolts and warshers. L.S. 174.75 2.12 370.47
TOTAL 6739.05 W
Add 1 % Water charges on "W" 67.39
TOTAL 6806.44 X
Add GST on "X" (multiplying
factor 0.1405) 956.30
TOTAL 7762.75 Y
Add 15% CPOH on "Y" 1164.41
TOTAL 8927.16 Z
Add Cess @ 1% on "Z" 89.27
Cost for 10 sqm. 9016.43
Cost for 1 sqm. 901.64
Say 901.65
SUB HEAD : 16- ROAD WORK 1328
16.71 Providing and fixing G.I. chain link fabric fencing of required width in mesh size
25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia
wire or nuts, bolts and washers as required complete as per the direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
G.I. chain link 25x25 mm mesh
= 10.00 sqm.
Wastage @ 5% = 0.50 sqm.
Total = 10.50 sqm.
8697 Chain link fabric fencing mesh of size
25x25 mm made of G.I. wire of dia
3 mm sqm 10.50 380.00 3990.00
9977 Carriage. L.S. 156.00 2.12 330.72
LABOUR
0103 Blacksmith 2nd class day 2.14 714.00 1527.96
0114 Beldar day 1.62 645.00 1044.90
9999 Sundries including G.I. wire, nuts and
bolts and warshers. L.S. 174.75 2.12 370.47
TOTAL 7264.05 W
Add 1 % Water charges on "W" 72.64
TOTAL 7336.69 X
Add GST on "X" (multiplying
factor 0.1405) 1030.81
TOTAL 8367.50 Y
Add 15% CPOH on "Y" 1255.12
TOTAL 9622.62 Z
Add Cess @ 1% on "Z" 96.23
Cost for 10 sqm. 9718.85
Cost for 1 sqm. 971.88
Say 971.90
16.72 Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.
Code Description Unit Quantity Rate Amount
Detail of cost for 2.25 cum
MATERIAL
22.5 cm thick stone (Hard)
1158 Stone for pitching 15 cm x 22.5 cm cum 2.25 600.00 1350.00
Carriage by mechanical transport
i/c loading unloading and stacking
2215 Carriage of Soling stone & masonary
stone cum 2.25 192.86 433.94
TOTAL 1783.94 W
Add 1 % Water charges on "W" 17.84
TOTAL 1801.77 X
Add GST on "X" (multiplying
factor 0.1405) 253.15
TOTAL 2054.92 Y
Add 15% CPOH on "Y" 308.24
TOTAL 2363.16 Z
Add Cess @ 1% on "Z" 23.63
Cost for 2.25 cum 2386.79
Cost for one cum 1060.80
Say 1060.80
SUB HEAD : 16- ROAD WORK 1329
16.73 Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer
dressed stones having no side less than 15 cm, with minimum depth of 20 cm
including preparing the bedding surface etc. all complete. (Payment for Stone
to be made separately).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0123 Mason (brick layer) 1st class day 1.08 784.00 846.72
0124 Mason (brick layer) 2nd class day 1.08 714.00 771.12
0114 Beldar day 2.15 645.00 1386.75
0115 Coolie day 1.61 645.00 1038.45
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 4057.37 W
Add 1 % Water charges on "W" 40.57
TOTAL 4097.94 X
Add GST on "X" (multiplying
factor 0.1405) 575.76
TOTAL 4673.71 Y
Add 15% CPOH on "Y" 701.06
TOTAL 5374.76 Z
Add Cess @ 1% on "Z" 53.75
Cost for 10 sqm 5428.51
Cost for one sqm 542.85
Say 542.85
16.74 75 mm thick back filling for pitching including supplying of required materials
and consolidation etc. complete with :
16.74.1 Moorum
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
0810 Moorum cum 7.50 500.00 3750.00
Carriage by mechanical transport i/c
loading unloading and stacking
2265 Carriage of Moorum cum 7.50 163.93 1229.48
LABOUR
0114 Beldar day 1.64 645.00 1057.80
0101 Bhisti day 0.13 714.00 92.82
TOTAL 6130.10 W
Add 1 % Water charges on "W" 61.30
TOTAL 6191.40 X
Add GST on "X" (multiplying
factor 0.1405) 869.89
TOTAL 7061.29 Y
Add 15% CPOH on "Y" 1059.19
TOTAL 8120.48 Z
Add Cess @ 1% on "Z" 81.20
Cost for 100 sqm 8201.68
Cost per sqm 82.02
Say 82.00
SUB HEAD : 16- ROAD WORK 1330
16.74.2 Stone aggregate 20 mm nominal size
Code Description Unit Quantity Rate Amount
Detail of cost for 100 sqm
MATERIAL
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 7.50 1400.00 10500.00
100sqm x7.50cm= 7.50 cum
2202 Carriage of Stone aggregate below
40 mm nominal size cum 7.50 163.93 1229.48
LABOUR
0114 Beldar day 2.05 645.00 1322.25
0101 Bhisti day 0.13 714.00 92.82
TOTAL 13144.55 W
Add 1 % Water charges on "W" 131.45
TOTAL 13275.99 X
Add GST on "X" (multiplying
factor 0.1405) 1865.28
TOTAL 15141.27 Y
Add 15% CPOH on "Y" 2271.19
TOTAL 17412.46 Z
Add Cess @ 1% on "Z" 174.12
Cost for 100 sqm 17586.58
Cost per sqm 175.87
Say 175.85
16.74.3 Stone aggregate 40 mm nominal size
Code Description Unit Quantity Rate Amount
Detail of cost for 100 sqm
MATERIAL
0293 Stone Aggregate (Single size) :
40 mm nominal size cum 7.50 1300.00 9750.00
100sqm x7.50cm= 7.50 cum
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 7.50 178.19 1336.43
LABOUR
0114 Beldar day 2.05 645.00 1322.25
0101 Bhisti day 0.13 714.00 92.82
TOTAL 12501.50 W
Add 1 % Water charges on "W" 125.01
TOTAL 12626.51 X
Add GST on "X" (multiplying
factor 0.1405) 1774.02
TOTAL 14400.53 Y
Add 15% CPOH on "Y" 2160.08
TOTAL 16560.61 Z
Add Cess @ 1% on "Z" 165.61
Cost for 100 sqm 16726.22
Cost per sqm 167.26
Say 167.25
SUB HEAD : 16- ROAD WORK 1331
16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete
from batching plant. The ready mixed concrete shall be laid and finished with
screed board vibrator , vacuum dewatering process and finally finished by
floating, brooming with wire brush etc. complete as per specifications and
directions of Engineer-in-charge. (The panel shuttering work shall be paid for
separately).
(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less
cement used as per design mix is payable/ recoverable separately).
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 cum
MATERIAL
Ready mix concrete M 25 = 1.00 cum.
i/c placing of concrete, vibrating,
leveling etc.
5.33.1.1 Rate as per Item No.5.33.1.1 of
SH:RCC cum 1.00 7997.30 7997.30 A
9999 Operational charges for vacuum
dewatering system i/c screed vibration,
placing of filter mat , top mat, vacuum
process, floating , troweling, Brooming
etc. L.S. 57.20 2.12 121.26
9999 T& P charges i/c consumable power
charges, loading , unloading and hire
charges of equipments L.S. 41.60 2.12 88.19
TOTAL 8206.76 W
Add 1 % Water charges on "W-A" 2.09
TOTAL 8208.85 X
Add GST on "X-A" (multiplying
factor 0.1405) 29.72
TOTAL 8238.57 Y
Add 15% CPOH on "Y-A" 36.19
TOTAL 8274.76 Z
Add Cess @ 1% on "Z-A" 2.77
Cost for 1 cum 8277.54
Say 8277.55
16.76 Deduct for using of M-20 grade concrete instead of M-25 grade concrete in C.C.
pavement.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
Cement for M-25 mix = 0.410 t
Cement for M - 20 mix = 0.383 t
Difference = 0.027 t
METERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.027 5000.00 135.00
2209 Carriage of Cement tonne 0.027 145.72 3.93
Plasticizer for M- 25 mix = 2.050kg
Plasticizer for M- 20 mix = 1.915 kg
Difference = 0.135 kg
SUB HEAD : 16- ROAD WORK 1332
Code Description Unit Quantity Rate Amount
7318 Plasticizer / super plasticizer kilogram 0.135 29.00 3.92
TOTAL 142.85 W
Add 1 % Water charges on "W" 1.43
TOTAL 144.28 X
Add GST on "X" (multiplying
factor 0.1405) 20.27
TOTAL 164.55 Y
Add 15% CPOH on "Y" 24.68
TOTAL 189.23 Z
Add Cess @ 1% on "Z" 1.89
Cost for 1 cum. 191.12
Say 191.10
16.77 Scarifying the existing bituminous road surface to a depth of 50 mm and disposal
of scarified material within all lifts and lead upto 1km (by mechanical means).
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
LABOUR
0128 Mate day 0.01 714.00 7.14
0114 Beldar day 0.25 645.00 161.25
MACHINERY
0038 Tractor with ripper attachment. day 0.01 1200.00 12.00
0014 Front end loader capacity 1.00 cum day 0.025 6000.00 150.00
0017 Hire and running charges of tipper day 0.02875 3750.00 107.81
TOTAL 438.20 W
Add 1 % Water charges on "W" 4.38
TOTAL 442.58 X
Add GST on "X" (multiplying
factor 0.1405) 62.18
TOTAL 504.77 Y
Add 15% CPOH on "Y" 75.72
TOTAL 580.48 Z
Add Cess @ 1% on "Z" 5.80
Cost for 100 sqm 586.29
Cost for 1 sqm 5.86
Say 5.85
16.78 Construction of granular sub-base by providing close graded Material
conforming to specifications, mixing in a mechanical mix plant at OMC, carriage
of mixed material by tippers to work site, for all leads & lifts, spreading in uniform
layers of specified thickness with motor grader on prepared surface and
compacting with vibratory power roller to achieve the desired density, complete
as per specifications and directions of Engineer-in-Charge.
SUB HEAD : 16- ROAD WORK 1333
16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having
CBR Value-30
Code Description Unit Quantity Rate Amount
Details of cost for 225 cum (450 tonnes)
MATERIAL
Close graded graunlar sub-base material
as per Grading-I of specifications
53mm to 9.5mm @ 50% = 144 cum
9.5 mm to 2.36mm @ 20% = 57 cum
2.36mm below @ 30% = 86.40 cum
0292 Stone Aggregate (Single size) :
50 mm nominal size cum 72.00 1000.00 72000.00
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 72.00 1350.00 97200.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 72.00 178.19 12829.68
2202 Carriage of Stone aggregate below
40 mm nominal size cum 72.00 163.93 11802.96
1179 Crushed stone 2.36 mm to 12.5 mm size cum 57.00 900.00 51300.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 57.00 163.93 9344.01
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 43.20 1400.00 60480.00
2904 Stone chippings/ screenings 150 micron
nominal size cum 43.20 1400.00 60480.00
2203 Carriage of Coarse sand cum 86.40 163.93 14163.55
Machinery/ Hire charges:
0059 Wet Mix Plant 60 TPH hour 6.00 950.00 5700.00
@75 tonne capacity
0070 Generator 100 KVA/125 KVA hour 6.00 300.00 1800.00
0057 Water Tanker 5 to 6 KL capacity hour 4.50 200.00 900.00
5 km lead with one trip per hour
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Tipper 10 tonne capacity( taking lead
= 10 Km) =450x10 =4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0050 Motor Grader 3.35 metre blade hour 6.00 2400.00 14400.00
0054 Vibratory roller 8 to 10 tonne hour 6.00 600.00 3600.00
LABOUR
0128 Mate day 0.40 714.00 285.60
0139 Skilled Beldar (for floor rubbing etc.) day 2.00 714.00 1428.00
0114 Beldar day 8.00 645.00 5160.00
TOTAL 447008.80 W
Add 1 % Water charges on "W" 4470.09
TOTAL 451478.89 X
Add GST on "X" (multiplying
factor 0.1405) 63432.78
TOTAL 514911.67 Y
Add 15% CPOH on "Y" 77236.75
TOTAL 592148.43 Z
Add Cess @ 1% on "Z" 5921.48
Cost for 225 cum(450 Tonne) 598069.91
Cost per cum. 2658.09
Say 2658.10
SUB HEAD : 16- ROAD WORK 1334
16.78.2 With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having
CBR Value-25
Code Description Unit Quantity Rate Amount
Details of cost for 225 cum (450 tonnes)
MATERIAL
Close graded graunlar sub-base material
as per Grading-I of specifications
26.5mm to 9.5mm @ 35% = 100.80 cum
9.5 mm to 2.36mm @ 25% = 72 cum
2.36mm below @ 40% = 115.20 cum
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 50.40 1350.00 68040.00
0297 Stone Aggregate (Single size) : 10 mm
nominal size cum 50.40 1350.00 68040.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 100.80 163.93 16524.14
1179 Crushed stone 2.36 mm to 12.5 mm size cum 72.00 900.00 64800.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 72.00 163.93 11802.96
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 57.60 1400.00 80640.00
2904 Stone chippings/ screenings 150 micron
nominal size cum 57.60 1400.00 80640.00
2203 Carriage of Coarse sand cum 115.20 163.93 18884.74
Machinery/ Hire charges:
0059 Wet Mix Plant 60 TPH hour 6.00 950.00 5700.00
@75 tonne capacity
0070 Generator 100 KVA/125 KVA hour 6.00 300.00 1800.00
0057 Water Tanker 5 to 6 KL capacity hour 4.50 200.00 900.00
5 km lead with one trip per hour
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Tipper 10 tonne capacity( taking lead=
10 Km) =450x10 =4500 tonne km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0050 Motor Grader 3.35 metre blade hour 6.00 2400.00 14400.00
0054 Vibratory roller 8 to 10 tonne hour 6.00 600.00 3600.00
LABOUR
0128 Mate day 0.40 714.00 285.60
0139 Skilled Beldar (for floor rubbing etc.) day 2.00 714.00 1428.00
0114 Beldar day 8.00 645.00 5160.00
TOTAL 466780.44 W
Add 1 % Water charges on "W" 4667.80
TOTAL 471448.24 X
Add GST on "X" (multiplying
factor 0.1405) 66238.48
TOTAL 537686.72 Y
Add 15% CPOH on "Y" 80653.01
TOTAL 618339.73 Z
Add Cess @ 1% on "Z" 6183.40
Cost for 225 cum(450 Tonne) 624523.13
Cost per cum. 2775.66
Say 2775.65
SUB HEAD : 16- ROAD WORK 1335
16.78.3 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having
CBR Value-20
Code Description Unit Quantity Rate Amount
Details of cost for 225 cum (450 tonnes)
MATERIAL
Close graded graunlar sub-base material
as per Grading-III of specifications
9.5mm to 4.75mm @ 35% = 100.80 cum
4.75 mm to 2.36mm @ 12.5%
= 36.00 cum
2.36mm below @ 52.5% = 151.20 cum
1179 Crushed stone 2.36 mm to 12.5 mm size cum 100.80 900.00 90720.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 100.80 163.93 16524.14
1179 Crushed stone 2.36 mm to 12.5 mm size cum 36.00 900.00 32400.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 36.00 163.93 5901.48
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 75.60 1400.00 105840.00
2904 Stone chippings/ screenings 150 micron
nominal size cum 75.60 1400.00 105840.00
2203 Carriage of Coarse sand cum 151.20 163.93 24786.22
Machinery/ Hire charges:
0059 Wet Mix Plant 60 TPH hour 6.00 950.00 5700.00
@75 tonne capacity
0070 Generator 100 KVA/125 KVA hour 6.00 300.00 1800.00
0057 Water Tanker 5 to 6 KL capacity hour 4.50 200.00 900.00
5 km lead with one trip per hour
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Tipper 10 tonne capacity( taking lead
= 10Km) =450x10 =4500 t.Km
0053 Tipper -5 Cum tonne km 4500.00 3.30 14850.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1485.00
0050 Motor Grader 3.35 metre blade hour 6.00 2400.00 14400.00
0054 Vibratory roller 8 to 10 tonne hour 6.00 600.00 3600.00
LABOUR
0128 Mate day 0.40 714.00 285.60
0139 Skilled Beldar (for floor rubbing etc.) day 2.00 714.00 1428.00
0114 Beldar day 8.00 645.00 5160.00
TOTAL 439420.44 W
Add 1 % Water charges on "W" 4394.20
TOTAL 443814.64 X
Add GST on "X" (multiplying
factor 0.1405) 62355.96
TOTAL 506170.60 Y
Add 15% CPOH on "Y" 75925.59
TOTAL 582096.19 Z
Add Cess @ 1% on "Z" 5820.96
Cost for 225 cum(450 Tonne) 587917.15
Cost per cum. 2612.97
Say 2612.95
SUB HEAD : 16- ROAD WORK 1336
16.79 Providing, laying, spreading and compacting graded stone aggregate (size range
53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including
premixing the material with water at OMC in for all leads & lifts, laying in uniform
layers with mechanical paverfinisher in sub- base / base course on well prepared
surface and compacting with vibratory roller of 8 to 10 tonne capacity to
achievethe desired density, complete as per specifications and directions of
Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 225 cum (495 tonne)
MATERIAL
Conforming to table ……
45mm to22.4mm @ 30% = 89.10 cum
Qty for 0292,0293,0294,0295 codes =
89.10 / 4 = 22.275 cum
Qty for 2206, 2202 codes = 89.10 /2
= 44.55 cum
22.4 mm to 2.36mm @ 40% =
118.80 cum
Qty for 0294,0295 codes = 118.80 /4
= 29.70 cum
Qty for 1179 code = 118.80 /2
= 59.40 cum
2.36 mm to 75 microon @ 30%
= 89.10 cum
Qty for 2903, 2904 codes = 89.10 / 2
= 44.55 cum
0292 Stone Aggregate (Single size) : 50 mm
nominal size cum 22.275 1000.00 22275.00
0293 Stone Aggregate (Single size) : 40 mm
nominal size cum 22.275 1300.00 28957.50
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 22.275 1350.00 30071.25
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 22.275 1400.00 31185.00
2206 Carriage of Stone aggregate 40 mm
nominal size and above cum 44.55 178.19 7938.36
2202 Carriage of Stone aggregate below
40 mm nominal size cum 44.55 163.93 7303.08
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 29.70 1350.00 40095.00
0295 Stone Aggregate (Single size) : 20 mm
nominal size cum 29.70 1400.00 41580.00
1179 Crushed stone 2.36 mm to 12.5 mm size cum 59.40 900.00 53460.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 118.80 163.93 19474.88
2903 Stone chippings/ screenings 4.75 mm
nominal size cum 44.55 1400.00 62370.00
2904 Stone chippings/ screenings 150 micron
nominal size cum 44.55 1400.00 62370.00
2203 Carriage of Coarse sand cum 89.10 163.93 14606.16
Machinery/ Hire charges:
0059 Wet Mix Plant 60 TPH hour 6.60 950.00 6270.00
@75 tonne capacity
0070 Generator 100 KVA/125 KVA hour 6.00 300.00 1800.00
SUB HEAD : 16- ROAD WORK 1337
Code Description Unit Quantity Rate Amount
0057 Water Tanker 5 to 6 KL capacity hour 3.00 200.00 600.00
5 km lead with one trip per hour
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
Tipper 10 tonne capacity( taking lead
= 10 Km) =495x10 =4950 tonne km
0053 Tipper -5 Cum tonne km 4950.00 3.30 16335.00
Add 10 per cent of cost of carriage to
cover cost of loading and unloading 1633.50
0065 Paver finisher Mechanical 100 TPH hour 6.00 800.00 4800.00
0054 Vibratory roller 8 to 10 tonne hour 3.90 600.00 2340.00
LABOUR
0128 Mate day 0.48 714.00 342.72
0139 Skilled Beldar (for floor rubbing etc.) day 2.00 714.00 1428.00
0114 Beldar day 10.00 645.00 6450.00
TOTAL 471485.46 W
Add 1 % Water charges on "W" 4714.85
TOTAL 476200.32 X
Add GST on "X" (multiplying
factor 0.1405) 66906.14
TOTAL 543106.46 Y
Add 15% CPOH on "Y" 81465.97
TOTAL 624572.43 Z
Add Cess @ 1% on "Z" 6245.72
Cost for 225 cum(450 Tonne) 630818.16
Cost per cum. 2803.64
Say 2803.65
16.80 Construction of dry lean cement concrete sub base over a prepared sub-grade
with coarse and fine aggregate conforming to IS:383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per specifications, cement content
not to be less than 150 Kg/cum, optimum moisture content to be determined
during trial length construction, concrete strength not to be less than 10 Mpa at
7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid
with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing
and curing etc. complete as per direction of Engineer-in- charge.
Code Description Unit Quantity Rate Amount
Details of cost for 450 cum (990 tonne)
MATERIAL
Crushed stone coarse aggregate of
25mm & 12.5 mm nominal sizes
graded as per specifications @ 0.90
cum/cum of concrete conforming to
specification. = 405 cum Coarse Sand
@0.45 m3 per cum of concrete = 203
cum
Cement @150 Kg. per cum of concrete
= 67.50 cum
Qty for 0294,0296 codes = 405 / 2
= 202.50 cum
SUB HEAD : 16- ROAD WORK 1338
Code Description Unit Quantity Rate Amount
0294 Stone Aggregate (Single size) : 25 mm
nominal size cum 202.50 1350.00 273375.00
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 202.50 1350.00 273375.00
0982 Coarse sand (zone III) cum 203.00 1500.00 304500.00
0367 Portland Cement (OPC-43 grade) tonne 67.50 5000.00 337500.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 405.00 163.93 66391.65
2203 Carriage of Coarse sand cum 203.00 163.93 33277.79
2209 Carriage of Cement tonne 67.50 145.72 9836.10
Machinery/ Hire charges:
0052 Front end loader 1 cum bucket capacity
(incl POL) hour 6.00 1300.00 7800.00
@75 tonne capacity
0066 Batching and Mixing Plant @ 75 cum
per hour hour 6.00 2400.00 14400.00
0069 Generator 250 KVA hour 6.00 400.00 2400.00
5 km lead with one trip per hour
0065 Paver finisher Mechanical 100 TPH hour 6.00 800.00 4800.00
0054 Vibratory roller 8 to 10 tonne hour 8.00 600.00 4800.00
0057 Water Tanker 5 to 6 KL capacity hour 8.00 200.00 1600.00
Tipper 10 tonne capacity (Taken
10km average lead)
990x10=9900 tonne km
0053 Tipper -5 Cum tonne km 9900.00 3.30 32670.00
Add 10 per cent of cost of carriage
to cover cost of loading and unloading 3267.00
LABOUR
0128 Mate day 1.12 714.00 799.68
0139 Skilled Beldar (for floor rubbing etc.) day 6.00 714.00 4284.00
0114 Beldar day 22.00 645.00 14190.00
TOTAL 1389266.22 W
Add 1 % Water charges on "W" 13892.66
TOTAL 1403158.88 X
Add GST on "X" (multiplying
factor 0.1405) 197143.82
TOTAL 1600302.71 Y
Add 15% CPOH on "Y" 240045.41
TOTAL 1840348.11 Z
Add Cess @ 1% on "Z" 18403.48
Cost for 450 cum(990 Tonne) 1858751.59
Cost per cum. 4130.56
Say 4130.55
16.81 Providing and erecting 2.00 metre high temporary barricading at site; each panel
of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS
tube posts/horizontal members/bracings covered with 1.63mm thick MS sheet.
The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The
panels shall be made so that gap of 50cm above the ground is available making
overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be
provided at the bottom having oval shaped holes of size 50x25mm at both ends
with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be
made to fix the barricading to avoid from overturning by providing 250mm long
SUB HEAD : 16- ROAD WORK 1339
expansion fasteners at both ends. The work shall be executed as per drawing/
direction of Engineer-in-Charge which includes writing and painting,
arrangement for traffic diversion such as traffic signals during construction at
site for day and night, glow lamps, reflective signs, marking, flags, caution tape
as directed by the Engineer-in-Charge. The barricading provided shall be
retained in position at site continuously i/c shifting of barricading from one
location to another location as many times as required during the execution of
the entire work till its completion. Rate include its maintenance for damages,
painting, all incidentals, labour materials, equipments and works required to
execute the job. The barricading shall not be removed without prior approval of
Engineer-in-Charge.
(Note :- One time payment shall be made for providing barricading from start of
work till completion of work i/c shifting. The barricading provided shall remain
to be the property of the contractor on completion of the work).
Code Description Unit Quantity Rate Amount
Details of cost for 2.5 metre
MATERIAL
16.81X Rate as per Sub Analysis No.16.81X metre 2.50 46.05 115.13
16.81Y Rate as per Sub Analysis No.16.81Y metre 2.50 1452.40 3631.00
13.50.3 Rate as per Item No.13.50.3 of
SH: FINISHING sqm 11.00 55.50 610.50 A
13.61.1 Rate as per Item No.13.61.1 of
SH: FINISHING sqm 11.00 131.45 1445.95 A
TOTAL 5802.58 W
Add 1 % Water charges on “W-A” 37.46
TOTAL 5840.04 X
Add GST on “X-A” (multiplying
factor 0.1405) 531.59
TOTAL 6371.63 Y
Add 15% CPOH on “Y-A” 647.28
TOTAL 7018.91 Z
Add Cess @ 1% on “Z-A” 49.62
Cost of 2.5 metre 7068.53
Cost of 1 metre 2827.41
Say 2827.40
16.81X Sub analysis item for material component of Item No. 16.81
Code Description Unit Quantity Rate Amount
Sub analysis item no.16.81X to be
used in Item No. 16.81
Details of cost for 2.5 meter
MATERIAL
M.S. Sheet 1.63mm thick = 1x2.50x2.00
= 5.00 sqm @ 12.80 kg/sqm = 64.00 kg
wastage @ 5%= 3.20 kg
Total = 67.20 kg
1013 Mild steel sheets for tanks quintal 0.672 4850.00 3259.20
MS Angle - 40 x 40 x 6 mm
Outframe=2x(2.50+2.00)=9.00 m
Vertical extra = 2x0.300 = 0.60 m
Horizontal = 1x2.50 =2.50 m
SUB HEAD : 16- ROAD WORK 1340
Code Description Unit Quantity Rate Amount
Bracing = 2x3.20 = 6.40 m
Bracing at bottom = 2x0.50 = 1.00 m
Total = 19.50 m @ 3.50 kg/m
= 68.25 kg +
wastage @ 5% = 3.14 kg
Total = 71.66 kg
1007 Structurals such as tees,angles
channels and R.S. joists quintal 0.717 4950.00 3549.15
M.S. Channel = 2x0.50 =1.00 m @
5.70 kg/m = 5.70 kg+
wastage @ 5% = 0.29 kg
Total = 5.99 kg
1007 Structurals such as tees, angles
channels and R.S. joists quintal 0.0599 4950.00 296.51
M.S. Flat 30x5 mm
Horizontal = 2x2.50 = 5.00 m
Vertical = 2x2.00 = 4.00 m
Total = 9.00 m @ 1.20 kg/m = 10.80 kg +
wastage @ 5% = 0.54 kg
Total = 11.34 kg
1008 Flats upto 10 mm in thickness quintal 0.1134 4850.00 549.99
2205 Carriage of Steel tonne 0.156 145.72 22.73
TOTAL 7677.58 P
Add for maintenance @ 10% on P 767.76 Q
Less for salvage value of material @
50% on P -3838.79
TOTAL 4606.55 S
Assuming that material will become
unserviceable after using 40 times,
cost of 2.5 metre using once = S/40
Cost of 2.5 meter 115.16
Cost of 1 meter 46.07
Say 46.05
16.81Y Sub analysis item for fabrication charges of Item No. 16.81
Code Description Unit Quantity Rate Amount
Sub analysis item no.16.81Y to be
used in Item No. 16.81
Details of cost for 2.5 metre
MATERIAL
1215 Welding by electric plant cm 165.00 2.00 330.00
Cutting, assembling and erection charges
LABOUR
0102 Blacksmith 1st class day 0.115 784.00 90.16
0103 Blacksmith 2nd class day 0.115 714.00 82.11
0100 Bandhani day 0.11 714.00 78.54
0114 Beldar day 0.83 645.00 535.35
9999 Sundries L.S. 12.10 2.12 25.65
Labour for riveting / bolting / cutting etc.
0116 Fitter (grade 1) day 0.41 784.00 321.44
0103 Blacksmith 2nd class day 0.54 714.00 385.56
0100 Bandhani day 0.70 714.00 499.80
0114 Beldar day 0.54 645.00 348.30
SUB HEAD : 16- ROAD WORK 1341
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar (for floor rubbing etc.) day 0.81 714.00 578.34
9999 Sundries L.S. 12.10 2.12 25.65
TOTAL 3300.90
Shifting including transportation,
re-erection etc. @ 10% 330.09
TOTAL Cost of 2.5 meter 3630.99
Cost of 1 meter 1452.40
Say 1452.40
16.82 Taking out existing kerb stones of all types from footpath/ central verge, including
removal of mortar etc., disposal of unserviceable material to the dumping
ground, for which payment shall be made separately and stacking of serviceable
material within 50 metre lead as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 100 meter
LABOUR
0114 Beldar day 0.75 645.00 483.75
0115 Coolie day 3.00 645.00 1935.00
9999 Sundries L.S. 2.00 2.12 4.24
TOTAL 2422.99 W
Add 1 % Water charges on "W" 24.23
TOTAL 2447.22 X
Add GST on "X" (multiplying factor 0.1405) 343.83
TOTAL 2791.05 Y
Add 15% CPOH on "Y" 418.66
TOTAL 3209.71 Z
Add Cess @ 1% on "Z" 32.10
Cost of 100 meter 3241.81
Cost of 1 meter 32.42
Say 32.40
16.83 Taking out existing CC interlocking paver blocks from footpath/ central verge,
including removal of rubbish etc., disposal of unserviceable material to the
dumping ground, for which payment shall be made separately and stacking of
serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
LABOUR
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 1.00 645.00 645.00
9999 Sundries L.S. 2.70 2.12 5.72
TOTAL 811.97 W
Add 1 % Water charges on "W" 8.12
TOTAL 820.09 X
Add GST on "X" (multiplying factor 0.1405) 115.22
TOTAL 935.32 Y
Add 15% CPOH on "Y" 140.30
TOTAL 1075.61 Z
Add Cess @ 1% on "Z" 10.76
Cost of 10 sqm. 1086.37
Cost of 1 sqm 108.64
Say 108.65
SUB HEAD : 16- ROAD WORK 1342
16.84 Laying old cement cocrete interlocking paver blocks of any design/ shape laid
in required line, level, curvature, colour and pattern over and including 50 mm
thick compacted bed of coarse sand, filling the joints with fine sand etc. all
complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall
be supplied by the department free of cost).
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
Bedding layer 50mm thick
0982 Coarse sand (zone III) cum 0.50 1500.00 750.00
Qty = 10 x 0.05 = 0.50 cum
2203 Carriage of Coarse sand cum 0.50 163.93 81.97
0983 Fine sand (zone IV) cum 0.15 900.00 135.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.15 163.93 24.59
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 0.50 645.00 322.50
TOTAL 2708.05 W
Add 1 % Water charges on "W" 27.08
TOTAL 2735.14 X
Add GST on "X" (multiplying
factor 0.1405) 384.29
TOTAL 3119.42 Y
Add 15% CPOH on "Y" 467.91
TOTAL 3587.33 Z
Add Cess @ 1% on "Z" 35.87
Cost of 10 sqm. 3623.21
Cost of 1 sqm 362.32
Say 362.30
16.85 Laying at or near ground level old kerb stones of all types in position to the
required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3
coarse sand), including making joints with or without grooves (thickness of
joints, except at sharp curve, shall not be more than 5 mm), including making
drainage opening wherever required etc. complete as per direction of Engineer-
in-charge. (Length of finished kerb edging shall be measured for payment). (Old
kerb stones shall be supplied by the department free of cost)
Code Description Unit Quantity Rate Amount
Details of cost for 100 meter.
MATERIAL
Number of kerb stones = 100 / 0.405
= 247 Nos.
Qty. = 247 x 0.40 x 0.375 x 0.20
= 7.41cum
No. of joints = 247 - 1 = 246 Nos.
Cement Mortar 1:3 for fixing joints =
246 x[(0.115 + 0.20)/2 x 0.375 x 0.005]
= 0.073 cum
SUB HEAD : 16- ROAD WORK 1343
Code Description Unit Quantity Rate Amount
3.8 Rate as per Item No.3.8 of
SH:MORTARS cum 0.073 5024.15 366.76
LABOUR
0123 Mason (brick layer) 1st class day 2.50 784.00 1960.00
0124 Mason (brick layer) 2nd class day 2.50 714.00 1785.00
0114 Beldar day 2.50 645.00 1612.50
0115 Coolie day 1.65 645.00 1064.25
TOTAL 6788.51 W
Add 1 % Water charges on "W" 67.89
TOTAL 6856.40 X
Add GST on "X" (multiplying factor 0.1405) 963.32
TOTAL 7819.72 Y
Add 15% CPOH on "Y" 1172.96
TOTAL 8992.68 Z
Add Cess @ 1% on "Z" 89.93
Cost of 100 meter. 9082.61
Cost of 1 meter. 90.83
Say 90.85
16.86 Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded
and pre polished machine cut granite stone of required size and shape of
approved shade, colour and texture in footpath, flooring cut granite stone of
required size and shape of approved shade, colour and texture in footpath,
flooring in road side plazas and similar locations, laid over 20mm thick base of
cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with
white cement mixed with matching pigment, epoxy touch ups etc. complete as
per direction of Engineer-in-Charge.
16.86.1 With granite stone of area less than 0.50 sqm.
Code Description Unit Quantity Rate Amount
Detail of cost for 0.5sqm.
Mirror polished granite 0.5 sqm.
Waste @5% = 0.025 +0.5 = 0.525 sqm.
7295 Granite of any colour, 18 mm thick
(slab area upto 0.50 sqm) sqm 0.525 1800.00 945.00
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.012 4355.20 52.26
LABOUR :
0123 Mason (brick layer) 1st class day 0.56 784.00 439.04
0114 Beldar day 0.05 645.00 32.25
0115 Coolie day 0.05 645.00 32.25
9999 Sundries L.S. 17.60 2.12 37.31
TOTAL 1538.11 W
Add 1 % Water charges on “W” 15.38
TOTAL 1553.50 X
Add GST on “X” (multiplying factor 0.1405) 218.27
TOTAL 1771.76 Y
Add 15% CPOH on “Y” 265.76
TOTAL 2037.53 Z
Add Cess @ 1% on “Z” 20.38
Cost of 0.5 sqm 2057.90
Cost per sqm. 4115.80
Say 4115.80
SUB HEAD : 16- ROAD WORK 1344
16.87 Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded
and pre polished machine cut granite stone of required size and shape of
approved shade, colour and texture in footpath, flooring in road side plazas
and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement
: 4 coarse sand) including grouting the joints with white cement mixed with
matching pigment, epoxy touch ups etc. complete as per direction of Engineer-
in-Charge.
16.87.1 With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 0.50 sqm
MATERIAL
Mirror polished granite 0.50 sqm +
Waste @5% total = 0.025. Total =
0.525 sqm
7296 Granite stone slab of colour Black,
Cherry/Ruby Red 30mm thick (slab
area less than 0.5 sqm) sqm 0.53 1900.00 997.50
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.012 4355.20 52.26
LABOUR :
0123 Mason (brick layer) 1st class day 0.56 784.00 439.04
0114 Beldar day 0.05 645.00 32.25
0115 Coolie day 0.05 645.00 32.25
9999 Sundries L.S. 17.60 2.12 37.31
TOTAL 1590.61 W
Add 1 % Water charges on "W" 15.91
TOTAL 1606.52 X
Add GST on "X" (multiplying
factor 0.1405) 225.72
TOTAL 1832.24 Y
Add 15% CPOH on "Y" 274.84
TOTAL 2107.07 Z
Add Cess @ 1% on "Z" 21.07
Cost of 0.5 sqm 2128.14
Cost of 1 sqm 4256.29
Say 4256.30
16.87.2 With granite stone of all colour except black, cherry/ruby red of area less than
0.50 sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 0.50 sqm
MATERIAL
Mirror polished granite 0.50 sqm +
Waste @5% total = 0.025. Total =
0.525 sqm
7300 Granite stone slab of all colour except
Black, Cherry/Ruby Red 30mm thick
(slab area less than 0.5 sqm) sqm 0.53 2100.00 1102.50
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.012 4355.20 52.26
SUB HEAD : 16- ROAD WORK 1345
Code Description Unit Quantity Rate Amount
LABOUR :
0123 Mason (brick layer) 1st class day 0.56 784.00 439.04
0114 Beldar day 0.05 645.00 32.25
0115 Coolie day 0.05 645.00 32.25
9999 Sundries L.S. 17.60 2.12 37.31
TOTAL 1695.61 W
Add 1 % Water charges on "W" 16.96
TOTAL 1712.57 X
Add GST on "X" (multiplying
factor 0.1405) 240.62
TOTAL 1953.19 Y
Add 15% CPOH on "Y" 292.98
TOTAL 2246.16 Z
Add Cess @ 1% on "Z" 22.46
Cost of 0.5 sqm 2268.63
Cost of 1 sqm 4537.25
Say 4537.25
16.88 Providing and laying matt finished vitrified tile of size 100x100x16mm having
water absorption less than 0.5% and conforming to IS: 15622 of approved make
in all colours and shades in out door floors such as footpath, court yard multi
models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse
sand) in all shapes & patterns including grouting the joints with white cement
mixed with matching pigments etc. complete as direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 sqm.
MATERIAL
Matt finished vitrified tile 100x100 x16mm
7895 Matt finished vitrified tile 100x100 x16mm sqm 1.00 910.00 910.00
9977 Carriage L.S. 6.24 2.12 13.23
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.024 4355.20 104.52
9999 Sundries L.S. 3.64 2.12 7.72
0367 Portland Cement (OPC-43 grade) tonne 0.0033 5000.00 16.50
LABOUR :
0123 Mason (brick layer) 1st class day 0.20 784.00 156.80
0115 Coolie day 0.20 645.00 129.00
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 1394.82 W
Add 1 % Water charges on "W" 13.95
TOTAL 1408.77 X
Add GST on "X" (multiplying
factor 0.1405) 197.93
TOTAL 1606.70 Y
Add 15% CPOH on "Y" 241.00
TOTAL 1847.70 Z
Add Cess @ 1% on "Z" 18.48
Cost per sqm. 1866.18
Say 1866.20
SUB HEAD : 16- ROAD WORK 1346
16.89 Providing and laying matt finished vitrified tile of size 300x300x9.8mm having
with water absorption less than 0.5% and conforming to IS: 15622 of approved
make in all colours and shades in for outdoor floors such as footpath, court
yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4
(1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints
with white cement mixed with matching pigments etc. complete as per direction
of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 sqm.
MATERIAL
Tile 300x300 x9.8mm = 1.00 sqm.
7896 Vitrified tile sqm 1.00 450.00 450.00
9977 Carriage L.S. 6.24 2.12 13.23
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.024 4355.20 104.52
9999 Sundries L.S. 3.64 2.12 7.72
0367 Portland Cement (OPC-43 grade) tonne 0.0033 5000.00 16.50
LABOUR :
0123 Mason (brick layer) 1st class day 0.20 784.00 156.80
0115 Coolie day 0.20 645.00 129.00
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 934.82 W
Add 1 % Water charges on "W" 9.35
TOTAL 944.17 X
Add GST on "X" (multiplying
factor 0.1405) 132.66
TOTAL 1076.82 Y
Add 15% CPOH on "Y" 161.52
TOTAL 1238.35 Z
Add Cess @ 1% on "Z" 12.38
Rate per sqm. 1250.73
Say 1250.75
16.90 Providing and laying tactile tile (for vision impaired persons as per standards)
of size 300x300x9.8mm having with water absorption less than 0.5% and
conforming to IS:15622 of approved make in all colours and shades in for outdoor
floors such as footpath, court yard, multi modals location etc., laid on 20mm
thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes &
patterns including grouting the joints with white cement mixed with matching
pigments etc. complete as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 sqm.
MATERIAL:
Tile 300x300 x9.8mm = 1.00 sqm.
7893 Tactile tile sqm 1.00 800.00 800.00
9977 Carriage L.S. 6.24 2.12 13.23
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.024 4355.20 104.52
9999 Sundries L.S. 3.64 2.12 7.72
0367 Portland Cement (OPC-43 grade) tonne 0.0033 5000.00 16.50
LABOUR :
0123 Mason (brick layer) 1st class day 0.20 784.00 156.80
SUB HEAD : 16- ROAD WORK 1347
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.20 645.00 129.00
9999 Sundries L.S. 26.91 2.12 57.05
TOTAL 1284.82 W
Add 1 % Water charges on "W" 12.85
TOTAL 1297.67 X
Add GST on "X" (multiplying
factor 0.1405) 182.32
TOTAL 1479.99 Y
Add 15% CPOH on "Y" 222.00
TOTAL 1701.99 Z
Add Cess @ 1% on "Z" 17.02
Cosr per sqm 1719.01
Say 1719.00
16.91 Providing and laying factory made chamfered edge Cement Concrete paver
blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required
strength, thickness & size/ shape, made by table vibratory method using PU
mould, laid in required colour & pattern over 50mm thick compacted bed of
sand, compacting and proper embedding/laying of inter locking paver blocks
into the sand bedding layer through vibratory compaction by using plate vibrator,
filling the joints with sand and cutting of paver blocks as per required size and
pattern, finishing and sweeping extra sand. complete all as per direction of
Engineer-in-Charge.
16.91.1 60mm thick cement concrete paver block of M-35 grade with approved colour,
design & pattern.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL :
7773 Coloured inter locking C.C. paver Block sqm 10.00 425.00 4250.00
0982 Coarse sand (zone-III) cum 0.50 1500.00 750.00
2203 Carriage of coarse sand cum 0.50 163.93 81.97
0983 Fine sand (zone IV) cum 0.11 900.00 99.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.11 163.93 18.03
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 0.50 645.00 322.50
9999 Sundries L.S. 25.00 2.12 53.00
TOTAL 6968.50 W
Add 1 % Water charges on "W" 69.68
TOTAL 7038.18 X
Add GST on "X" (multiplying
factor 0.1405) 988.86
TOTAL 8027.05 Y
Add 15% CPOH on "Y" 1204.06
TOTAL 9231.10 Z
Add Cess @ 1% on "Z" 92.31
Cost of 10 Sqm 9323.41
Cost of 1 Sqm 932.34
Say 932.35
SUB HEAD : 16- ROAD WORK 1348
16.91.2 80 mm thick C.C. paver block of M-30 grade with approved color design and
pattern.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm.
MATERIALS :
8785 Interlocking C.C. paver block
(80 mm thick, M-30) sqm 10.00 485.00 4850.00
0982 Coarse sand (zone 111) (10 x
0.050 = 0.50 cum ) cum 0.50 1500.00 750.00
2203 Carriage of Coarse sand cum 0.50 163.93 81.97
0983 Fine sand (zone IV) cum 0.15 900.00 135.00
2261 Carriage of Fine sand cum 0.15 163.93 24.59
Labour for Laying
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 0.50 645.00 322.50
TOTAL 7558.05 W
Add 1 % Water charges on "W" 75.58
TOTAL 7633.64 X
Add GST on "X" (multiplying
factor 0.1405) 1072.53
TOTAL 8706.16 Y
Add 15% CPOH on "Y" 1305.92
TOTAL 10012.08 Z
Add Cess @ 1% on "Z" 100.12
Cost of 10 Sqm 10112.21
Cost of 1 Sqm 1011.22
Say 1011.20
16.92 Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel
dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar
1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar
including ruled pointing etc. complete as per direction of engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm.
MATERIALS :
Stone size 10x10x7.50cm =1sqm
7774 Stone size 10x10x7.50cm each 827.00 9.00 7443.00
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.434 4355.20 1890.16
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
LABOUR :
0124 Mason (brick layer) 2nd class day 1.08 714.00 771.12
0114 Beldar day 0.25 645.00 161.25
0115 Coolie day 1.62 645.00 1044.90
0101 Bhisti day 0.27 714.00 192.78
SUB HEAD : 16- ROAD WORK 1349
Code Description Unit Quantity Rate Amount
13.33.1 Rate as per Item No.13.33.1 of
SH: FINISHING sqm 10.00 319.35 3193.50 A
TOTAL 14796.71 W
Add 1 % Water charges on "W-A" 116.03
TOTAL 14912.74 X
Add GST on "X-A" (multiplying
factor 0.1405) 1646.55
TOTAL 16559.29 Y
Add 15% CPOH on "Y-A" 2004.87
TOTAL 18564.16 Z
Add Cess @ 1% on "Z-A" 153.71
Cost of 10 sqm. 18717.87
Cost of 1 sqm. 1871.79
Say 1871.80
16.93 Providing and placing in position 100 mm thick factory made machine batched
& machine mixed Precast RCC Rectangular Covers on drains of footpath of
various sizes, of M-25 grade cement concrete for RCC work, including cost of
centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @
maximum 100mm c/c on both ways , neat cement punning on finished surface,
properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly
painted over priming coat , reinforcement to be welded at edges with MS sheet
and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads &
lift, handling at site etc. all complete as per direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost of 1 No of size 1.50 x
0.40 = 0.60 sqm
MATERIALS :
Precast RCC M-25
5.33.1.1 Rate as per Item No.5.33.1.1 of
SH: REINFORCED CEMENT
CONCRETE cum 0.06 7997.30 479.84 A
Reinforcement TMT
5.22.6 Rate as per Item No.5.22.6 of
SH: REINFORCED CEMENT
CONCRETE Kg 4.59 89.65 411.49 A
Welding by gas plant/ Electric plant
10.22 Rate as per Item No.10.22 of
SH: STEEL WORK cm 82.00 3.40 278.80 A
M.S. sheet 1.60 mm thick
2x(1.50+0.40)x0.10x0.016x7850
=4.77kg
1013 Mild steel sheets for tanks quintal 0.0477 4850.00 231.35
Paint 2x(1.50+0.40)x0.10=0.38sqm
13.61.1 Rate as per Item No.13.61.1 of
SH: FINISHING sqm 0.38 131.45 49.95 A
Neat Cement Punning
1x1.50x0.40=0.60 sqm
SUB HEAD : 16- ROAD WORK 1350
Code Description Unit Quantity Rate Amount
13.18 Rate as per Item No.13.18 of
SH: FINISHING sqm 0.60 67.80 40.68 A
TOTAL 1492.11 W
Add 1 % Water charges on "W-A" 2.31
TOTAL 1494.42 X
Add GST on "X-A" (multiplying
factor 0.1405) 32.83
TOTAL 1527.25 Y
Add 15% CPOH on "Y-A" 39.97
TOTAL 1567.22 Z
Add Cess @ 1% on "Z-A" 3.06
Cost of 0.60 sqm. 1570.29
Cost of 1 sqm. 2617.15
Say 2617.15
16.94 Providing & making Gabion structure with Mechanically Woven Double Twisted
Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH
Clause 2500, of required size, Mesh Type 10x12 (D=100 mm with tolerance of ±
2%) Zinc coated, Mesh wire diameter 3.0 mm, mechanically edged/selvedged
with partitions at every 1m interval and shall have minimum 10 numbers of
openings per meter of mesh perpendicular to twist, tying with lacing wire of
diameter 2.2mm, supplied @ 3% by weight of Gabion boxes, filled with boulders
with least dimension of 200 mm, as per drawing, all complete as per direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details cost of one Gabion box/Crates
of size 2mx1mx1m = 2 cum
MATERIAL
8576 Crates made of Mesh type 10x12
(D=100 mm) Zn coated. (Mesh wire
diameter 3.00 mm). sqm 11.00 200.00 2200.00
Surface area required = 11.00 sqm.
7753 Stone boulder with least dimension
200mm cum 2.00 810.00 1620.00
2206 Carriage of boulder cum 2.00 178.19 356.38
LABOUR
0128 Mate day 0.10 714.00 71.40
0125 Mason (for plain stone work) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.50 645.00 967.50
TOTAL 5572.28 W
Add 1 % Water charges on "W" 55.72
TOTAL 5628.00 X
Add GST on "X" (multiplying
factor 0.1405) 790.73
TOTAL 6418.74 Y
Add 15% CPOH on "Y" 962.81
TOTAL 7381.55 Z
Add Cess @ 1% on "Z" 73.82
Cost of 2 cum 7455.36
Cost of 1 cum 3727.68
Say 3727.70
SUB HEAD : 16- ROAD WORK 1351
16.95 Providing & making Gabion structure with Mechanically Woven Double Twisted
Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH
Clause 2500, of required size, Mesh Type 10x12(D=100 mm with tolerance of ±
2%) Zinic+PVC coated, Mesh wire diameter2.7/3.7mm, mechanically edged/
selvedged with partitions at every 1m interval and shall have minimum 10
numbers of openings per meter of mesh perpendicular to twist, tying with lacing
wire of diameter 2.2/3.2mm(ID/OD), supplied @3% by weight of Gabion boxes,
filled with boulders with least dimension of 200 mm, as per drawing, all complete
as per directions of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details cost of one Gabion box/Crates
of size 2mx1mx1m = 2 cum
MATERIAL
8577 Crates made of Mesh type 10x12
(D=100 mm) Zn+PVC coated. Mesh
wire diameter 2.70/3.70 mm (ID/OD). sqm 11.00 250.00 2750.00
Surface area required = 11.00 sqm.
7753 Stone boulder with least dimension
200mm cum 2.00 810.00 1620.00
LABOUR
0128 Mate day 0.10 714.00 71.40
0125 Mason (for plain stone work) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.50 645.00 967.50
TOTAL 5765.90 W
Add 1 % Water charges on "W" 57.66
TOTAL 5823.56 X
Add GST on "X" (multiplying
factor 0.1405) 818.21
TOTAL 6641.77 Y
Add 15% CPOH on "Y" 996.27
TOTAL 7638.03 Z
Add Cess @ 1% on "Z" 76.38
Cost of 2 cum 7714.41
Cost of 1 cum 3857.21
Say 3857.20
16.96 Providing & making Gabion structure with Mechanically Woven Double Twisted
Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH
Clause 2500, of required size, Mesh Type 10x12(D=100 mm with tolerance of
±2%), Zinic+10% Al alloy+PVC coated, Mesh wire diameter 2.7/3.7mm (ID/OD),
mechanically edged/selvedged with partitions at every 1m interval and shall
have minimum 10 numbers of openings per meter of mesh perpendicular to
twist, tying with lacing wire of diameter 2.2/3.2mm(ID/OD), supplied @3% by
weight of Gabion boxes, filled with boulders with least dimension of 200 mm,
as per drawing, all complete as per directions of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details cost of one Gabion box/Crates
of size 2mx1mx1m = 2 cum
SUB HEAD : 16- ROAD WORK 1352
Code Description Unit Quantity Rate Amount
MATERIAL
8578 Crates made of Mesh type 10x12
(D=100 mm) Zn+10% Al alloy + PVC
coated. Mesh wire diameter 2.70/
3.70 mm (ID/OD). sqm 11.00 290.00 3190.00
Surface area required = 11.00 sqm.
7753 Stone boulder with least dimension
200mm cum 2.00 810.00 1620.00
LABOUR
0128 Mate day 0.10 714.00 71.40
0125 Mason (for plain stone work) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.50 645.00 967.50
TOTAL 6205.90 W
Add 1 % Water charges on "W" 62.06
TOTAL 6267.96 X
Add GST on "X" (multiplying
factor 0.1405) 880.65
TOTAL 7148.61 Y
Add 15% CPOH on "Y" 1072.29
TOTAL 8220.90 Z
Add Cess @ 1% on "Z" 82.21
Cost of 2 cum 8303.11
Cost of 1 cum 4151.55
Say 4151.55
SUB HEAD : 16- ROAD WORK 1353
SUB HEAD : 17.0
SANITARY INSTALLATIONS
1355
17.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with
100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing
cistern, including flush pipe, with manually controlled device (handle lever)
conforming to IS : 7231, with all fittings and fixtures complete, including cutting
and making good the walls and floors wherever required:
17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral
type foot rests
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
1954 Vitreous china orrisa type w.c. pan
size 580 mm each 1.00 1290.00 1290.00
7358 Flushing Cistern P.V.C. 10 lts capacity
(low level) (White) (with fittings,
accessories and flush pipe) each 1.00 575.00 575.00
1896 100 mm S.C.I. trap with vent heel each 1.00 325.00 325.00
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.25 784.00 980.00
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 4321.10 W
Add 1 % Water charges on "W" 43.21
TOTAL 4364.31 X
Add GST on "X" (multiplying
factor 0.1405) 613.19
TOTAL 4977.49 Y
Add 15% CPOH on "Y" 746.62
TOTAL 5724.12 Z
Add Cess @ 1% on "Z" 57.24
Cost of each 5781.36
Say 5781.35
17.1.2 Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm
with flush pipe and integrated type foot rests
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
7805 Salem Stainless steel AISI - 304 (18/8)
Orrisa pattern W.C. pan 724mm X
578mm each 1.00 4500.00 4500.00
7358 Flushing Cistern P.V.C. 10 lts capacity
(low level) (White) (with fittings,
accessories and flush pipe) each 1.00 575.00 575.00
1896 100 mm S.C.I. trap with vent heel each 1.00 325.00 325.00
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.25 784.00 980.00
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1357
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.00 645.00 645.00
TOTAL 7531.10 W
Add 1 % Water charges on "W" 75.31
TOTAL 7606.41 X
Add GST on "X" (multiplying
factor 0.1405) 1068.70
TOTAL 8675.11 Y
Add 15% CPOH on "Y" 1301.27
TOTAL 9976.38 Z
Add Cess @ 1% on "Z" 99.76
Cost of each 10076.14
Say 10076.15
17.2 Providing and fixing white vitreous china pedestal type water closet (European
type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern,
including flush pipe, with manually controlled device (handle lever), conforming
to IS : 7231, with all fittings and fixtures complete, including cutting and making
good the walls and floors wherever required :
17.2.1 W.C. pan with ISI marked white solid plastic seat and lid
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
1875 White plastic seat (solid)with lid
C.P.brass hinges and rubber buffers each 1.00 410.00 410.00
1955 Vitreous china pedestal type water closet each 1.00 1025.00 1025.00
7358 Flushing Cistern P.V.C. 10 lts capacity
(low level) (White) (with fittings,
accessories and flush pipe) each 1.00 575.00 575.00
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.25 784.00 980.00
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 4141.10 W
Add 1 % Water charges on "W" 41.41
TOTAL 4182.51 X
Add GST on "X" (multiplying
factor 0.1405) 587.64
TOTAL 4770.15 Y
Add 15% CPOH on "Y" 715.52
TOTAL 5485.67 Z
Add Cess @ 1% on "Z" 54.86
Cost of each 5540.53
Say 5540.55
SUB HEAD : 17- SANITARY INSTALLATIONS 1358
17.2.2 W.C. pan with ISI marked black solid plastic seat and lid
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
1876 Black plastic seat (solid) with lid
C.P.brass hinges and rubber buffers each 1.00 325.00 325.00
1955 Vitreous china pedestal type water closet each 1.00 1025.00 1025.00
7358 Flushing Cistern P.V.C. 10 lts capacity
(low level) (White) (with fittings,
accessories and flush pipe) each 1.00 575.00 575.00
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.25 784.00 980.00
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 4056.10 W
Add 1 % Water charges on "W" 40.56
TOTAL 4096.66 X
Add GST on "X" (multiplying
factor 0.1405) 575.58
TOTAL 4672.24 Y
Add 15% CPOH on "Y" 700.84
TOTAL 5373.08 Z
Add Cess @ 1% on "Z" 53.73
Cost of each 5426.81
Say 5426.80
17.3 Providing and fixing white vitreous china pedestal type water closet (European
type) with seat and lid, 10 litre low level white vitreous china flushing cistern
& C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow
arrangement with specials of standard make and mosquito proof coupling of
approved municipal design complete, including painting of fittings and
brackets, cutting and making good the walls and floors wherever required :
17.3.1 W.C. pan with ISI marked white solid plastic seat and lid
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
1875 White plastic seat (solid)with lid
C.P.brass hinges and rubber buffers each 1.00 410.00 410.00
1955 Vitreous china pedestal type water closet each 1.00 1025.00 1025.00
7006 Vitreous china 10 litres low level cistern
with fittings each 1.00 1200.00 1200.00
9999 Overflow arrangement and specials for
oveflow pipe L.S. 62.79 2.12 133.11
1350 Mosquito proof coupling of approved
design each 1.00 30.00 30.00
9999 Plugs ,screws etc. L.S. 13.52 2.12 28.66
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
SUB HEAD : 17- SANITARY INSTALLATIONS 1359
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 5188.05 W
Add 1 % Water charges on "W" 51.88
TOTAL 5239.93 X
Add GST on "X" (multiplying
factor 0.1405) 736.21
TOTAL 5976.14 Y
Add 15% CPOH on "Y" 896.42
TOTAL 6872.56 Z
Add Cess @ 1% on "Z" 68.73
Cost of each 6941.29
Say 6941.30
17.3.2 W.C. pan with ISI marked black solid plastic seat and lid
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
1876 Black plastic seat (solid) with lid
C.P.brass hinges and rubber buffers each 1.00 325.00 325.00
1955 Vitreous china pedestal type water closet each 1.00 1025.00 1025.00
7006 Vitreous china 10 litres low level cistern
with fittings each 1.00 1200.00 1200.00
9999 Overflow arrangement and specials for
oveflow pipe L.S. 62.79 2.12 133.11
1350 Mosquito proof coupling of approved
design each 1.00 30.00 30.00
9999 Plugs, screws etc. L.S. 13.52 2.12 28.66
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 5103.05 W
Add 1 % Water charges on "W" 51.03
TOTAL 5154.08 X
Add GST on "X" (multiplying
factor 0.1405) 724.15
TOTAL 5878.23 Y
Add 15% CPOH on "Y" 881.73
TOTAL 6759.96 Z
Add Cess @ 1% on "Z" 67.60
Cost of each 6827.56
Say 6827.55
SUB HEAD : 17- SANITARY INSTALLATIONS 1360
17.4 Providing and fixing white vitreous china flat back or wall corner type lipped
front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively
with automatic flushing cistern with standard flush pipe and C.P. brass
spreaders with brass unions and G.I clamps complete, including painting of
fittings and brackets, cutting and making good the walls and floors wherever
required :
17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1913 Vitreous china lipped front urinal each 1.00 470.00 470.00
7359 P.V.C. automatic flushing cistern 5 lts
capacity each 1.00 450.00 450.00
7375 G.I. flush pipe and C.P. brass spreader
including C.P. connecting pipe Single
lipped urinal each 1.00 445.00 445.00
9999 Red lead, white lead and gaskit L.S. 13.52 2.12 28.66
9999 Plugs ,screws etc. L.S. 13.52 2.12 28.66
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9999 Painting of fittings etc. L.S. 39.00 2.12 82.68
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 0.88 784.00 689.92
0123 Mason (brick layer) 1st class day 0.88 784.00 689.92
0114 Beldar day 1.50 645.00 967.50
TOTAL 3938.06 W
Add 1 % Water charges on "W" 39.38
TOTAL 3977.44 X
Add GST on "X" (multiplying
factor 0.1405) 558.83
TOTAL 4536.27 Y
Add 15% CPOH on "Y" 680.44
TOTAL 5216.71 Z
Add Cess @ 1% on "Z" 52.17
Cost of each 5268.87
Say 5268.85
17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1913 Vitreous china lipped front urinal each 2.00 470.00 940.00
7359 P.V.C. automatic flushing cistern
5 lts capacity each 1.00 450.00 450.00
7376 G.I. flush pipe and C.P. brass spreader
including C.P. connecting pipe Range
of two lipped urinals each 1.00 765.00 765.00
9999 Red lead, white lead and gaskit L.S. 20.28 2.12 42.99
9999 Plugs ,screws etc. L.S. 20.28 2.12 42.99
9999 Cement, sand and grit etc. L.S. 20.28 2.12 42.99
9999 Painting of fittings etc. L.S. 39.00 2.12 82.68
9977 Carriage of materials L.S. 26.91 2.12 57.05
SUB HEAD : 17- SANITARY INSTALLATIONS 1361
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 1.50 784.00 1176.00
0123 Mason (brick layer) 1st class day 1.50 784.00 1176.00
0114 Beldar day 2.00 645.00 1290.00
TOTAL 6065.71 W
Add 1 % Water charges on "W" 60.66
TOTAL 6126.37 X
Add GST on "X" (multiplying
factor 0.1405) 860.75
TOTAL 6987.12 Y
Add 15% CPOH on "Y" 1048.07
TOTAL 8035.19 Z
Add Cess @ 1% on "Z" 80.35
Cost of each 8115.54
Say 8115.55
17.4.3 Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1913 Vitreous china lipped front urinal each 3.00 470.00 1410.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
7377 G.I. flush pipe and C.P. brass spreader
including C.P. connecting pipe Range
of three lipped urinals each 1.00 1050.00 1050.00
9999 Red lead, white lead and gaskit L.S. 33.67 2.12 71.38
9999 Plugs ,screws etc. L.S. 33.67 2.12 71.38
9999 Cement, sand and grit etc. L.S. 33.67 2.12 71.38
9999 Painting of fittings etc. L.S. 39.00 2.12 82.68
9977 Carriage of materials L.S. 40.30 2.12 85.44
LABOUR
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0123 Mason (brick layer) 1st class day 2.00 784.00 1568.00
0114 Beldar day 3.00 645.00 1935.00
TOTAL 8413.26 W
Add 1 % Water charges on "W" 84.13
TOTAL 8497.39 X
Add GST on "X" (multiplying
factor 0.1405) 1193.88
TOTAL 9691.27 Y
Add 15% CPOH on "Y" 1453.69
TOTAL 11144.96 Z
Add Cess @ 1% on "Z" 111.45
Cost of each 11256.41
Say 11256.40
SUB HEAD : 17- SANITARY INSTALLATIONS 1362
17.4.4 Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1913 Vitreous china lipped front urinal each 4.00 470.00 1880.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
7378 G.I. flush pipe and C.P. brass spreader
including C.P. connecting pipe Range
of four lipped urinals each 1.00 1430.00 1430.00
9999 Red lead, white lead and gaskit L.S. 53.82 2.12 114.10
9999 Plugs ,screws etc. L.S. 53.82 2.12 114.10
9999 Cement, sand and grit etc. L.S. 53.82 2.12 114.10
9999 Painting of fittings etc. L.S. 39.00 2.12 82.68
9977 Carriage of materials L.S. 53.82 2.12 114.10
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0123 Mason (brick layer) 1st class day 3.00 784.00 2352.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 11633.07 W
Add 1 % Water charges on "W" 116.33
TOTAL 11749.40 X
Add GST on "X" (multiplying
factor 0.1405) 1650.79
TOTAL 13400.20 Y
Add 15% CPOH on "Y" 2010.03
TOTAL 15410.22 Z
Add Cess @ 1% on "Z" 154.10
Cost of each 15564.33
Say 15564.35
17.5 Providing and fixing white vitreous china flat back half stall urinal of size
580x380x350 mm with white PVC automatic flushing cistern, with fittings,
standard size C.P. brass flush pipe, spreaders with unions and clamps (all in
C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and
other couplings in C.P. brass, including painting of fittings and cutting and
making good the walls and floors wherever required :
17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7379 White vitreous china clay half stall
urinal flat back 580x380x350 mm or
angle back 450x375x350 mm with
waste fittings as per IS : 2556 each 1.00 865.00 865.00
7359 P.V.C. automatic flushing cistern 5 lts
capacity each 1.00 450.00 450.00
1532 Flush pipe with union spreaders and
clamps all in C.P. brass for single stall each 1.00 310.00 310.00
1891 C.I. trap for standard urinal with vent
arm with operating and other couplings
in C.P.brass: 50 mm dia each 1.00 190.00 190.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1363
Code Description Unit Quantity Rate Amount
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 40.43 2.12 85.71
LABOUR
0116 Fitter (grade 1) day 1.75 784.00 1372.00
0123 Mason (brick layer) 1st class day 2.00 784.00 1568.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 7570.09 W
Add 1 % Water charges on "W" 75.70
TOTAL 7645.79 X
Add GST on "X" (multiplying
factor 0.1405) 1074.23
TOTAL 8720.02 Y
Add 15% CPOH on "Y" 1308.00
TOTAL 10028.02 Z
Add Cess @ 1% on "Z" 100.28
Cost of each 10128.30
Say 10128.30
17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7379 White vitreous china clay half stall
urinal flat back 580x380x350 mm or
angle back 450x375x350 mm with
waste fittings as per IS : 2556 each 2.00 865.00 1730.00
7359 P.V.C. automatic flushing cistern
5 lts capacity each 1.00 450.00 450.00
1533 Flush pipe with union spreaders and
clamps all in C.P. brass for double stall each 1.00 425.00 425.00
1891 C.I. trap for standard urinal with vent
arm with operating and other couplings
in C.P.brass: 50 mm dia each 1.00 190.00 190.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 53.82 2.12 114.10
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 53.82 2.12 114.10
LABOUR
0116 Fitter (grade 1) day 2.50 784.00 1960.00
0123 Mason (brick layer) 1st class day 3.00 784.00 2352.00
0114 Beldar day 6.00 645.00 3870.00
TOTAL 11297.52 W
Add 1 % Water charges on "W" 112.98
TOTAL 11410.50 X
Add GST on "X" (multiplying
factor 0.1405) 1603.17
TOTAL 13013.67 Y
Add 15% CPOH on "Y" 1952.05
TOTAL 14965.72 Z
Add Cess @ 1% on "Z" 149.66
Cost of each 15115.38
Say 15115.40
SUB HEAD : 17- SANITARY INSTALLATIONS 1364
17.5.3 Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7379 White vitreous china clay half stall
urinal flat back 580x380x350 mm or
angle back 450x375x350 mm with
waste fittings as per IS : 2556 each 3.00 865.00 2595.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
1534 Flush pipe with union spreaders and
clamps all in C.P. brass for range of
three stall each 1.00 525.00 525.00
1893 C.I. trap for standard urinal with vent
arm with operating and other couplings
in C.P.brass: 80 mm dia each 1.00 225.00 225.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 80.73 2.12 171.15
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 67.21 2.12 142.49
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0123 Mason (brick layer) 1st class day 3.50 784.00 2744.00
0114 Beldar day 7.00 645.00 4515.00
TOTAL 13861.96 W
Add 1 % Water charges on "W" 138.62
TOTAL 14000.58 X
Add GST on "X" (multiplying
factor 0.1405) 1967.08
TOTAL 15967.66 Y
Add 15% CPOH on "Y" 2395.15
TOTAL 18362.81 Z
Add Cess @ 1% on "Z" 183.63
Cost of each 18546.44
Say 18546.45
17.5.4 Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7379 White vitreous china clay half stall
urinal flat back 580x380x350 mm or
angle back 450x375x350 mm with
waste fittings as per IS : 2556 each 4.00 865.00 3460.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
1535 Flush pipe with union spreaders and
clamps all in C.P. brass for range of
four stall each 1.00 610.00 610.00
1893 C.I. trap for standard urinal with vent
arm with operating and other couplings
in C.P.brass: 80 mm dia each 1.00 225.00 225.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
SUB HEAD : 17- SANITARY INSTALLATIONS 1365
Code Description Unit Quantity Rate Amount
9999 Cement, sand and grit etc. L.S. 107.64 2.12 228.20
9999 Painting of fittings etc. L.S. 39.00 2.12 82.68
9977 Carriage of materials L.S. 80.73 2.12 171.15
LABOUR
0116 Fitter (grade 1) day 3.50 784.00 2744.00
0123 Mason (brick layer) 1st class day 4.00 784.00 3136.00
0114 Beldar day 8.00 645.00 5160.00
TOTAL 16354.23 W
Add 1 % Water charges on "W" 163.54
TOTAL 16517.77 X
Add GST on "X" (multiplying
factor 0.1405) 2320.75
TOTAL 18838.52 Y
Add 15% CPOH on "Y" 2825.78
TOTAL 21664.30 Z
Add Cess @ 1% on "Z" 216.64
Cost of each 21880.94
Say 21880.95
17.6 Providing and fixing one piece construction white vitreous china squatting
plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing
cistern, with fittings, standard size G.I. / PVC flush pipe for back and front
flush with standard spreader pipes with fittings, G.I clamps and C.P. brass
coupling complete, including painting of fittings and cutting and making good
the walls and floors etc. wherever required :
17.6.1 Single squatting plate with 5 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1915 Vitreous china squatting plate urinal each 1.00 1053.00 1053.00
7359 P.V.C. automatic flushing cistern
5 lts capacity each 1.00 450.00 450.00
1540 Flush pipe and spreaders G.I.for single
set of one squatting plate urinal each 1.00 190.00 190.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 26.91 2.12 57.05
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 1.75 784.00 1372.00
0123 Mason (brick layer) 1st class day 0.75 784.00 588.00
0114 Beldar day 3.00 645.00 1935.00
TOTAL 5794.42 W
Add 1 % Water charges on "W" 57.94
TOTAL 5852.37 X
Add GST on "X" (multiplying
factor 0.1405) 822.26
TOTAL 6674.63 Y
Add 15% CPOH on "Y" 1001.19
TOTAL 7675.82 Z
Add Cess @ 1% on "Z" 76.76
Cost of each 7752.58
Say 7752.60
SUB HEAD : 17- SANITARY INSTALLATIONS 1366
17.6.2 Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1915 Vitreous china squatting plate urinal each 2.00 1053.00 2106.00
7359 P.V.C. automatic flushing cistern
5 lts capacity each 1.00 450.00 450.00
1541 Flush pipe and spreaders G.I.for range
of two squatting plates urinal each 1.00 275.00 275.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 53.82 2.12 114.10
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 33.15 2.12 70.28
LABOUR
0116 Fitter (grade 1) day 2.50 784.00 1960.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 8431.70 W
Add 1 % Water charges on "W" 84.32
TOTAL 8516.02 X
Add GST on "X" (multiplying
factor 0.1405) 1196.50
TOTAL 9712.52 Y
Add 15% CPOH on "Y" 1456.88
TOTAL 11169.40 Z
Add Cess @ 1% on "Z" 111.69
Cost of each 11281.09
Say 11281.10
17.6.3 Range of three squatting plates with 10 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1915 Vitreous china squatting plate urinal each 3.00 1053.00 3159.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
1542 Flush pipe and spreaders G.I.for range
of three squatting plates urinal each 1.00 310.00 310.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 80.73 2.12 171.15
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 42.12 2.12 89.29
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0123 Mason (brick layer) 1st class day 1.50 784.00 1176.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1367
Code Description Unit Quantity Rate Amount
0114 Beldar day 5.00 645.00 3225.00
TOTAL 11074.77 W
Add 1 % Water charges on "W" 110.75
TOTAL 11185.52 X
Add GST on "X" (multiplying
factor 0.1405) 1571.56
TOTAL 12757.08 Y
Add 15% CPOH on "Y" 1913.56
TOTAL 14670.64 Z
Add Cess @ 1% on "Z" 146.71
Cost of each 14817.35
Say 14817.35
17.6.4 Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1915 Vitreous china squatting plate urinal each 4.00 1053.00 4212.00
7361 P.V.C. automatic flushing cistern
10 lts capacity each 1.00 500.00 500.00
1543 Flush pipe and spreaders G.I.for range
of four squatting plates urinal each 1.00 450.00 450.00
9999 Red lead, white lead and gaskit L.S. 17.55 2.12 37.21
9999 Cement, sand and grit etc. L.S. 107.64 2.12 228.20
9999 Painting of fittings etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 69.03 2.12 146.34
LABOUR
0116 Fitter (grade 1) day 3.50 784.00 2744.00
0123 Mason (brick layer) 1st class day 1.75 784.00 1372.00
0114 Beldar day 5.50 645.00 3547.50
TOTAL 13292.37 W
Add 1 % Water charges on "W" 132.92
TOTAL 13425.29 X
Add GST on "X" (multiplying
factor 0.1405) 1886.25
TOTAL 15311.54 Y
Add 15% CPOH on "Y" 2296.73
TOTAL 17608.27 Z
Add Cess @ 1% on "Z" 176.08
Cost of each 17784.36
Say 17784.35
SUB HEAD : 17- SANITARY INSTALLATIONS 1368
17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar
taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings
and brackets, cutting and making good the walls wherever require:
17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.
brass pillar taps
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1947 Vitreous china flat back wash basin
630x450 mm each 1.00 725.00 725.00
1885 15 mm C.P.brass tap each 2.00 270.00 540.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1700.37 W
Add 1 % Water charges on "W" 17.00
TOTAL 1717.37 X
Add GST on "X" (multiplying
factor 0.1405) 241.29
TOTAL 1958.67 Y
Add 15% CPOH on "Y" 293.80
TOTAL 2252.47 Z
Add Cess @ 1% on "Z" 22.52
Cost of each 2274.99
Say 2275.00
17.7.2 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P.
brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1947 Vitreous china flat back wash basin
630x450 mm each 1.00 725.00 725.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
SUB HEAD : 17- SANITARY INSTALLATIONS 1369
Code Description Unit Quantity Rate Amount
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1430.37 W
Add 1 % Water charges on "W" 14.30
TOTAL 1444.67 X
Add GST on "X" (multiplying
factor 0.1405) 202.98
TOTAL 1647.65 Y
Add 15% CPOH on "Y" 247.15
TOTAL 1894.80 Z
Add Cess @ 1% on "Z" 18.95
Cost of each 1913.75
Say 1913.75
17.7.3 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P.
brass pillar taps
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3229 Vitreous china flat back wash basin
550x400 mm each 1.00 550.00 550.00
1885 15 mm C.P.brass tap each 2.00 270.00 540.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1525.37 W
Add 1 % Water charges on "W" 15.25
TOTAL 1540.62 X
Add GST on "X" (multiplying
factor 0.1405) 216.46
TOTAL 1757.08 Y
Add 15% CPOH on "Y" 263.56
TOTAL 2020.65 Z
Add Cess @ 1% on "Z" 20.21
Cost of each 2040.85
Say 2040.85
17.7.4 White Vitreous China Flat back wash basin size 550x 400 mm with single
15 mm C.P. brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3229 Vitreous china flat back wash basin
550x400 mm each 1.00 550.00 550.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1370
Code Description Unit Quantity Rate Amount
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1255.37 W
Add 1 % Water charges on "W" 12.55
TOTAL 1267.92 X
Add GST on "X" (multiplying
factor 0.1405) 178.14
TOTAL 1446.07 Y
Add 15% CPOH on "Y" 216.91
TOTAL 1662.98 Z
Add Cess @ 1% on "Z" 16.63
Cost of each 1679.61
Say 1679.60
17.7.5 White Vitreous China Angle back wash basin size 600 x 480 mm with single
15mm C.P. brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1949 Vitreous china angle back wash basin
600x480 mm each 1.00 725.00 725.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1430.37 W
Add 1 % Water charges on "W" 14.30
TOTAL 1444.67 X
Add GST on "X" (multiplying
factor 0.1405) 202.98
TOTAL 1647.65 Y
Add 15% CPOH on "Y" 247.15
TOTAL 1894.80 Z
Add Cess @ 1% on "Z" 18.95
Cost of each 1913.75
Say 1913.75
SUB HEAD : 17- SANITARY INSTALLATIONS 1371
17.7.6 White Vitreous China Angle back wash basin size 400 x 400 mm with single 15
mm C.P. brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1950 Vitreous china angle back wash basin
400x400 mm each 1.00 425.00 425.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1130.37 W
Add 1 % Water charges on "W" 11.30
TOTAL 1141.67 X
Add GST on "X" (multiplying
factor 0.1405) 160.41
TOTAL 1302.08 Y
Add 15% CPOH on "Y" 195.31
TOTAL 1497.39 Z
Add Cess @ 1% on "Z" 14.97
Cost of each 1512.37
Say 1512.35
17.7.7 White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm
C.P. brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7004 Vitreous china flat back wash basin
450x300 mm each 1.00 280.00 280.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
SUB HEAD : 17- SANITARY INSTALLATIONS 1372
Code Description Unit Quantity Rate Amount
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 985.37 W
Add 1 % Water charges on "W" 9.85
TOTAL 995.22 X
Add GST on "X" (multiplying
factor 0.1405) 139.83
TOTAL 1135.05 Y
Add 15% CPOH on "Y" 170.26
TOTAL 1305.31 Z
Add Cess @ 1% on "Z" 13.05
Cost of each 1318.37
Say 1318.35
17.7.8 White Vitreous China Surgeon type wash basin of size 660x460 mm with a
pair of 15 mm C.P. brass pillar taps with elbow including operated levers
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3213 Vitreous china Surgeon type wash
basin of size 660x460 mm each 1.00 1100.00 1100.00
7363 15 mm C.P. brass tap with elbow
operation lever each 2.00 430.00 860.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 2395.37 W
Add 1 % Water charges on "W" 23.95
TOTAL 2419.32 X
Add GST on "X" (multiplying
factor 0.1405) 339.92
TOTAL 2759.24 Y
Add 15% CPOH on "Y" 413.89
TOTAL 3173.13 Z
Add Cess @ 1% on "Z" 31.73
Cost of each 3204.86
Say 3204.85
SUB HEAD : 17- SANITARY INSTALLATIONS 1373
17.7.9 White Vitreous China Surgeon type wash basin of size 660x460 mm with single
15 mm C.P. brass pillar taps with elbow operated levers ISI Marked
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3213 Vitreous china Surgeon type wash
basin of size 660x460 mm each 1.00 1100.00 1100.00
7363 15 mm C.P. brass tap with elbow
operation lever each 1.00 430.00 430.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1965.37 W
Add 1 % Water charges on "W" 19.65
TOTAL 1985.02 X
Add GST on "X" (multiplying
factor 0.1405) 278.90
TOTAL 2263.92 Y
Add 15% CPOH on "Y" 339.59
TOTAL 2603.51 Z
Add Cess @ 1% on "Z" 26.04
Cost of each 2629.54
Say 2629.55
17.7.10 Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm
C.P. brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7806 Salem Stainless steel AISI -
304 (18/8) Round basin 405mm X
355mm each 1.00 1500.00 1500.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
SUB HEAD : 17- SANITARY INSTALLATIONS 1374
Code Description Unit Quantity Rate Amount
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 2205.37 W
Add 1 % Water charges on "W" 22.05
TOTAL 2227.42 X
Add GST on "X" (multiplying
factor 0.1405) 312.95
TOTAL 2540.38 Y
Add 15% CPOH on "Y" 381.06
TOTAL 2921.43 Z
Add Cess @ 1% on "Z" 29.21
Cost of each 2950.65
Say 2950.65
17.7.11 Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P.
brass pillar tap
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7807 Salem Stainless steel AISI -
304 (18/8) Wash basin 530mm X
345mm each 1.00 2000.00 2000.00
1885 15 mm C.P.brass tap each 1.00 270.00 270.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 2705.37 W
Add 1 % Water charges on "W" 27.05
TOTAL 2732.42 X
Add GST on "X" (multiplying
factor 0.1405) 383.91
TOTAL 3116.33 Y
Add 15% CPOH on "Y" 467.45
TOTAL 3583.78 Z
Add Cess @ 1% on "Z" 35.84
Cost of each 3619.62
Say 3619.60
SUB HEAD : 17- SANITARY INSTALLATIONS 1375
17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single
hole basin mixer of approved quality and make, including painting of fittings
and brackets, cutting and making good the walls wherever required:-
(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass
single hole basin mixer
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3229 Vitreous china flat back wash basin
550x400 mm each 1.00 550.00 550.00
9001 C.P. Brass Centre Hole Basin Mixer
With Cast Spout ( Kigston/Marc/Prima/
Parko/Hindware) each 1.00 1600.00 1600.00
1951 C.P. brass waste 32 mm each 1.00 85.00 85.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, Sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 2585.37 W
Add 1 % Water charges on "W" 25.85
TOTAL 2611.22 X
Add GST on "X" (multiplying
factor 0.1405) 366.88
TOTAL 2978.10 Y
Add 15% CPOH on "Y" 446.72
TOTAL 3424.82 Z
Add Cess @ 1% on "Z" 34.25
Cost of each 3459.07
Say 3459.05
17.7B Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock,
32 mm PTMT waste coupling of standard pattern, including painting of fittings
and brackets, cutting and making good the walls wherever required. White
Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT
pillar cock.
Code Description Unit Quantity Rate Amount
Details of cost for 1 No.
MATERIAL
3229 Vitreous china flat back wash basin
550x400 mm each 1.00 550.00 550.00
7406 PTMT pillar cock each 1.00 115.00 115.00
7491 PTMT - Waste Coupling 31/32 mm each 1.00 34.00 34.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Red Lead, White Lead and Gasket L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc L.S. 13.39 2.12 28.39
SUB HEAD : 17- SANITARY INSTALLATIONS 1376
Code Description Unit Quantity Rate Amount
9999 Painting of brackets, fittings etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
9999 Fixing Charges L.S. 53.82 2.12 114.10
TOTAL 1049.37 W
Add 1 % Water charges on "W" 10.49
TOTAL 1059.86 X
Add GST on "X" (multiplying
factor 0.1405) 148.91
TOTAL 1208.78 Y
Add 15% CPOH on "Y" 181.32
TOTAL 1390.09 Z
Add Cess @ 1% on "Z" 13.90
Cost of each 1403.99
Say 1404.00
17.8 Providing and fixing white vitreous china pedestal for wash basin completely
recessed at the back for the reception of pipes and fittings.
Code Description Unit Quantity Rate Amount
Details of cost for one pedestal
MATERIAL
1396 Vitrous china pedestal for wash basin each 1.00 950.00 950.00
9999 White cement mortar L.S. 40.30 2.12 85.44
9988 Carriage of materials and fixing charges L.S. 40.43 2.12 85.71
TOTAL 1121.15 W
Add 1 % Water charges on "W" 11.21
TOTAL 1132.36 X
Add GST on "X" (multiplying
factor 0.1405) 159.10
TOTAL 1291.46 Y
Add 15% CPOH on "Y" 193.72
TOTAL 1485.17 Z
Add Cess @ 1% on "Z" 14.85
Cost of each 1500.03
Say 1500.05
17.9 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with
rubber plug, 40 mm C.P. brass waste complete, including painting the fittings
and brackets, cutting and making good the walls wherever required:
17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1863 Fire clay kitchen sink: 600x450x
250 mm each 1.00 1300.00 1300.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
1315 C.P.brass chain with 40 mm dia
rubber plug each 1.00 40.00 40.00
1952 C.P. brass waste 40 mm each 1.00 100.00 100.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1377
Code Description Unit Quantity Rate Amount
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting brackets etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 2468.67 W
Add 1 % Water charges on "W" 24.69
TOTAL 2493.36 X
Add GST on "X" (multiplying
factor 0.1405) 350.32
TOTAL 2843.68 Y
Add 15% CPOH on "Y" 426.55
TOTAL 3270.23 Z
Add Cess @ 1% on "Z" 32.70
Cost of each 3302.93
Say 3302.95
17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983
with C.I. brackets and stainless steel plug 40 mm, including painting of fittings
and brackets, cutting and making good the walls wherever required :
17.10.1 Kitchen sink with drain board
17.10.1.1 510x1040 mm bowl depth 250 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7095 Stainless steel kitchen sink - with drain
board bowl depth 250 mm. each 1.00 3000.00 3000.00
1309 C.I. bracket for wash basin and sinks pair 2.00 88.00 176.00
9999 Cement, sand and grit etc. L.S. 27.04 2.12 57.32
9999 Painting of brackets etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.60 784.00 470.40
0114 Beldar day 0.82 645.00 528.90
TOTAL 4490.82 W
Add 1 % Water charges on "W" 44.91
TOTAL 4535.72 X
Add GST on "X" (multiplying
factor 0.1405) 637.27
TOTAL 5172.99 Y
Add 15% CPOH on "Y" 775.95
TOTAL 5948.94 Z
Add Cess @ 1% on "Z" 59.49
Cost of each 6008.43
Say 6008.45
SUB HEAD : 17- SANITARY INSTALLATIONS 1378
17.10.1.2 510x1040 mm bowl depth 225 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7096 Stainlees steel kitchen sink - with drain
board 510 x 1040mm bowl depth
225 mm. each 1.00 3500.00 3500.00
1309 C.I. bracket for wash basin and sinks pair 2.00 88.00 176.00
9999 Cement, sand and grit etc. L.S. 27.04 2.12 57.32
9999 Painting of brackets etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.60 784.00 470.40
0114 Beldar day 0.82 645.00 528.90
TOTAL 4990.82 W
Add 1 % Water charges on "W" 49.91
TOTAL 5040.72 X
Add GST on "X" (multiplying
factor 0.1405) 708.22
TOTAL 5748.95 Y
Add 15% CPOH on "Y" 862.34
TOTAL 6611.29 Z
Add Cess @ 1% on "Z" 66.11
Cost of each 6677.40
Say 6677.40
17.10.1.3 510x1040 mm bowl depth 200 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7097 Stainlees steel kitchen sink - with drain
board 510 x 1040mm bowl depth
200 mm. each 1.00 3200.00 3200.00
1309 C.I. bracket for wash basin and sinks pair 2.00 88.00 176.00
9999 Cement, sand and grit etc. L.S. 27.04 2.12 57.32
9999 Painting of brackets etc. L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.60 784.00 470.40
0114 Beldar day 0.82 645.00 528.90
TOTAL 4690.82 W
Add 1 % Water charges on "W" 46.91
TOTAL 4737.72 X
Add GST on "X" (multiplying
factor 0.1405) 665.65
TOTAL 5403.37 Y
Add 15% CPOH on "Y" 810.51
TOTAL 6213.88 Z
Add Cess @ 1% on "Z" 62.14
Cost of each 6276.02
Say 6276.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1379
17.10.1.4 510x1040 mm bowl depth 178 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7098 Stainless steel kitchen sink - with
drain board 510x1040mm bowl depth
178 mm each 1.00 3000.00 3000.00
1309 C.I. bracket for wash basin and sinks pair 2.00 88.00 176.00
9999 Cement, sand and grit etc. L.S. 27.04 2.12 57.32
9999 Painting brackets L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.60 784.00 470.40
0114 Beldar day 0.82 645.00 528.90
TOTAL 4490.82 W
Add 1 % Water charges on "W" 44.91
TOTAL 4535.72 X
Add GST on "X" (multiplying
factor 0.1405) 637.27
TOTAL 5172.99 Y
Add 15% CPOH on "Y" 775.95
TOTAL 5948.94 Z
Add Cess @ 1% on "Z" 59.49
Cost of each 6008.43
Say 6008.45
17.10.2 Kitchen sink without drain board
17.10.2.1 610x510 mm bowl depth 200 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7101 Stainless steel kitchen sink - without
drain board 610x510mm bowl depth
200 mm each 1.00 2200.00 2200.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9999 Painting brackets L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 3194.77 W
Add 1 % Water charges on "W" 31.95
TOTAL 3226.72 X
Add GST on "X" (multiplying
factor 0.1405) 453.35
TOTAL 3680.08 Y
Add 15% CPOH on "Y" 552.01
TOTAL 4232.09 Z
Add Cess @ 1% on "Z" 42.32
Cost of each 4274.41
Say 4274.40
SUB HEAD : 17- SANITARY INSTALLATIONS 1380
17.10.2.2 610x460 mm bowl depth 200 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7102 Stainless steel kitchen sink - without
drain board 610x460mm bowl depth
200 mm. each 1.00 1500.00 1500.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9999 Painting brackets L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 2494.77 W
Add 1 % Water charges on "W" 24.95
TOTAL 2519.72 X
Add GST on "X" (multiplying
factor 0.1405) 354.02
TOTAL 2873.74 Y
Add 15% CPOH on "Y" 431.06
TOTAL 3304.80 Z
Add Cess @ 1% on "Z" 33.05
Cost of each 3337.85
Say 3337.85
17.10.2.3 470x420 mm bowl depth 178 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7103 Stainless steel kitchen sink - without
drain board 470x420mm bowl depth
178 mm each 1.00 1200.00 1200.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9999 Painting brackets L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 2194.77 W
Add 1 % Water charges on "W" 21.95
TOTAL 2216.72 X
Add GST on "X" (multiplying
factor 0.1405) 311.45
TOTAL 2528.17 Y
Add 15% CPOH on "Y" 379.23
TOTAL 2907.40 Z
Add Cess @ 1% on "Z" 29.07
Cost of each 2936.47
Say 2936.45
SUB HEAD : 17- SANITARY INSTALLATIONS 1381
17.11 Providing and fixing white vitreous china laboratory sink with C.I. brackets,
C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P.
brass trap with necessary C.P. brass unions complete, including painting of
fittings and brackets, cutting and making good the wall wherever required :
17.11.1 Size 450x300x150 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1871 White vitreous china laboratry sink
450x300x150 mm each 1.00 1500.00 1500.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
1315 C.P.brass chain with 40 mm dia
rubber plug each 1.00 40.00 40.00
1952 C.P. brass waste 40 mm each 1.00 100.00 100.00
1895 C.P.brass trap40 mm dia each 1.00 315.00 315.00
3617 C.P.brass union 40 mm dia each 1.00 210.00 210.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Sundries L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 3193.67 W
Add 1 % Water charges on "W" 31.94
TOTAL 3225.61 X
Add GST on "X" (multiplying
factor 0.1405) 453.20
TOTAL 3678.81 Y
Add 15% CPOH on "Y" 551.82
TOTAL 4230.63 Z
Add Cess @ 1% on "Z" 42.31
Cost of each 4272.94
Say 4272.95
17.11.2 Size 600x450x200 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1872 White vitreous china laboratry sink
600x450x200 mm each 1.00 2500.00 2500.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
1315 C.P.brass chain with 40 mm dia
rubber plug each 1.00 40.00 40.00
1952 C.P. brass waste 40 mm each 1.00 100.00 100.00
1895 C.P.brass trap40 mm dia each 1.00 315.00 315.00
3617 C.P.brass union 40 mm dia each 1.00 210.00 210.00
9999 Red lead, white lead and gaskit L.S. 16.12 2.12 34.17
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Sundries L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 13.52 2.12 28.66
SUB HEAD : 17- SANITARY INSTALLATIONS 1382
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0114 Beldar day 0.56 645.00 361.20
TOTAL 4193.67 W
Add 1 % Water charges on "W" 41.94
TOTAL 4235.61 X
Add GST on "X" (multiplying
factor 0.1405) 595.10
TOTAL 4830.71 Y
Add 15% CPOH on "Y" 724.61
TOTAL 5555.32 Z
Add Cess @ 1% on "Z" 55.55
Cost of each 5610.87
Say 5610.85
17.12 Providing and fixing draining board with C.I. brackets including painting of
brackets, cutting and making good the walls wherever required :
17.12.1 White glazed fire clay draining board of size 600x450x 25 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7364 White glazed fire clay draining board
600x450x25 mm each 1.00 500.00 500.00
1309 C.I. bracket for wash basin and sinks pair 1.00 88.00 88.00
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9999 Painting brackets etc. L.S. 26.00 2.12 55.12
9977 Carriage of materials L.S. 7.80 2.12 16.54
LABOUR
0116 Fitter (grade 1) day 0.06 784.00 47.04
0123 Mason (brick layer) 1st class day 0.17 784.00 133.28
0114 Beldar day 0.22 645.00 141.90
TOTAL 1010.26 W
Add 1 % Water charges on "W" 10.10
TOTAL 1020.37 X
Add GST on "X" (multiplying
factor 0.1405) 143.36
TOTAL 1163.73 Y
Add 15% CPOH on "Y" 174.56
TOTAL 1338.29 Z
Add Cess @ 1% on "Z" 13.38
Cost of each 1351.67
Say 1351.65
SUB HEAD : 17- SANITARY INSTALLATIONS 1383
17.13 Providing and fixing white vitreous china water closet squatting pan (Indian
type) :
17.13.1 Long pattern W.C. pan of size 580 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1953 Vitreous china indian type w.c.
pan size 580 mm each 1.00 475.00 475.00
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1246.55 W
Add 1 % Water charges on "W" 12.47
TOTAL 1259.01 X
Add GST on "X" (multiplying
factor 0.1405) 176.89
TOTAL 1435.91 Y
Add 15% CPOH on "Y" 215.39
TOTAL 1651.29 Z
Add Cess @ 1% on "Z" 16.51
Cost of each 1667.81
Say 1667.80
17.13.2 Orissa pattern W.C. pan of size 580x440 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1954 Vitreous china orrisa type w.c. pan
size 580 mm each 1.00 1290.00 1290.00
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 2061.55 W
Add 1 % Water charges on "W" 20.62
TOTAL 2082.16 X
Add GST on "X" (multiplying
factor 0.1405) 292.54
TOTAL 2374.71 Y
Add 15% CPOH on "Y" 356.21
TOTAL 2730.92 Z
Add Cess @ 1% on "Z" 27.31
Cost of each 2758.22
Say 2758.20
SUB HEAD : 17- SANITARY INSTALLATIONS 1384
17.14 Extra for using coloured W.C. pan instead of white W.C. pan :
17.14.1 Orissa pattern W.C. pan 580x440 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
Difference in cost of
7104 Coloured Orissa pattern W.C. pan
580x440 mm each 1.00 1600.00 1600.00
1954 Vitreous china orrisa type w.c. pan
size 580 mm each -1.00 1290.00 -1290.00
TOTAL 310.00 W
Add 1 % Water charges on "W" 3.10
TOTAL 313.10 X
Add GST on "X" (multiplying
factor 0.1405) 43.99
TOTAL 357.09 Y
Add 15% CPOH on "Y" 53.56
TOTAL 410.65 Z
Add Cess @ 1% on "Z" 4.11
Cost of each 414.76
Say 414.75
17.15 Providing and fixing white vitreous china pedestal type (European type/ wash
down type) water closet pan.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1955 Vitreous china pedestal type water closet each 1.00 1025.00 1025.00
9999 Cement, sand and grit etc. L.S. 13.39 2.12 28.39
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1796.55 W
Add 1 % Water charges on "W" 17.97
TOTAL 1814.51 X
Add GST on "X" (multiplying
factor 0.1405) 254.94
TOTAL 2069.45 Y
Add 15% CPOH on "Y" 310.42
TOTAL 2379.87 Z
Add Cess @ 1% on "Z" 23.80
Cost of each 2403.67
Say 2403.65
SUB HEAD : 17- SANITARY INSTALLATIONS 1385
17.16 Extra for using coloured pedestal type W.C pan (European type) with low level
cistern of same colour instead of white vitreous china W.C pan and cistern.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7105 Coloured Pedestal type W.C. pan
580x440 mm (European type) each 1.00 850.00 850.00
Deduct
1955 Vitreous china pedestal type water closet each -1.00 1025.00 -1025.00
7106 Coloured Vitreous china 10 lit. low
level cistern each 1.00 1000.00 1000.00
Deduct
7005 Vitreous china 10 litres low level
cistern without fittings each -1.00 700.00 -700.00
TOTAL 125.00 W
Add 1 % Water charges on "W" 1.25
TOTAL 126.25 X
Add GST on "X" (multiplying
factor 0.1405) 17.74
TOTAL 143.99 Y
Add 15% CPOH on "Y" 21.60
TOTAL 165.59 Z
Add Cess @ 1% on "Z" 1.66
Cost of each 167.24
Say 167.25
17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre
long with S.S. triangular plate to Eureopean type W.C. of quality and make as
approved by Engineer - in - charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 No.
1313 8 mm dia C.P. Brass/ S.S. Jet with
flexible tube upto 1 metre long with
S.S. tringular plate for Eureopean type
W.C.(Hindware/Kingston/Prima/Parko/
Marc) each 1.00 200.00 200.00
9999 Carriage of material and fixing charges L.S. 11.20 2.12 23.74
TOTAL 223.74 W
Add 1 % Water charges on "W" 2.24
TOTAL 225.98 X
Add GST on "X" (multiplying
factor 0.1405) 31.75
TOTAL 257.73 Y
Add 15% CPOH on "Y" 38.66
TOTAL 296.39 Z
Add Cess @ 1% on "Z" 2.96
Cost of each 299.36
Say 299.35
SUB HEAD : 17- SANITARY INSTALLATIONS 1386
17.17 Providing and fixing a pair of white vitreous china foot rests of standard pattern
for squatting pan water closet :
17.17.1 250x130x30 mm
Code Description Unit Quantity Rate Amount
Details of cost for one pair
MATERIAL
1363 Vitreous china foot rests 250x130x30 mm pair 1.00 100.00 100.00
9988 Cement, sand including carriage of
materials L.S. 8.06 2.12 17.09
LABOUR
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
TOTAL 164.13 W
Add 1 % Water charges on "W" 1.64
TOTAL 165.77 X
Add GST on "X" (multiplying
factor 0.1405) 23.29
TOTAL 189.06 Y
Add 15% CPOH on "Y" 28.36
TOTAL 217.42 Z
Add Cess @ 1% on "Z" 2.17
Cost for 1 pair 219.59
Say 219.60
17.17.2 250x125x25 mm
Code Description Unit Quantity Rate Amount
Details of cost for one pair
MATERIAL
1970 Vitreous china foot rests 250x125x25 mm pair 1.00 103.00 103.00
9988 Cement, sand including carriage
of materials L.S. 8.06 2.12 17.09
LABOUR
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
TOTAL 167.13 W
Add 1 % Water charges on "W" 1.67
TOTAL 168.80 X
Add GST on "X" (multiplying
factor 0.1405) 23.72
TOTAL 192.51 Y
Add 15% CPOH on "Y" 28.88
TOTAL 221.39 Z
Add Cess @ 1% on "Z" 2.21
Cost for 1 pair 223.61
Say 223.60
SUB HEAD : 17- SANITARY INSTALLATIONS 1387
17.18 Providing and fixing P.V.C. low level flushing cistern with manually controlled
device (handle lever) conforming to IS : 7231, with all fittings and fixtures
complete.
17.18.1 10 litre capacity - White
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7358 Flushing Cistern P.V.C. 10 lts capacity
(low level) (White) (with fittings,
accessories and flush pipe) each 1.00 575.00 575.00
9977 Carriage of materials L.S. 5.20 2.12 11.02
LABOUR
(Considering 1 fitter and 1 beldar can
fix 8 cistern in one day)
0116 Fitter (grade 1) day 0.125 784.00 98.00
0114 Beldar day 0.125 645.00 80.63
TOTAL 764.65 W
Add 1 % Water charges on "W" 7.65
TOTAL 772.30 X
Add GST on "X" (multiplying
factor 0.1405) 108.51
TOTAL 880.80 Y
Add 15% CPOH on "Y" 132.12
TOTAL 1012.92 Z
Add Cess @ 1% on "Z" 10.13
Cost of each 1023.05
Say 1023.05
17.18.2 10 litre capacity - coloured
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7123 Coloured High density polythylene/
poly propylene 10 lit. (full flush)
capacity controlled low level flushing
cistern with fittings each 1.00 550.00 550.00
9977 Carriage of materials L.S. 5.20 2.12 11.02
LABOUR
(Considering 1 fitter and 1 beldar can
fix 8 cistern in one day)
0116 Fitter (grade 1) day 0.125 784.00 98.00
0114 Beldar day 0.125 645.00 80.63
TOTAL 739.65 W
Add 1 % Water charges on "W" 7.40
TOTAL 747.05 X
Add GST on "X" (multiplying
factor 0.1405) 104.96
TOTAL 852.01 Y
Add 15% CPOH on "Y" 127.80
TOTAL 979.81 Z
Add Cess @ 1% on "Z" 9.80
Cost of each 989.60
Say 989.60
SUB HEAD : 17- SANITARY INSTALLATIONS 1388
17.19 Providing and fixing controlled flush, low level cistern made of vitreous china
with all fittings complete.
17.19.1 10 litre (full flush) capacity-white
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7126 White Vitreous china 10 lit. (full flush)
capacity controlled low level flushing
cistern with all fittings each 1.00 700.00 700.00
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1443.16 W
Add 1 % Water charges on "W" 14.43
TOTAL 1457.59 X
Add GST on "X" (multiplying
factor 0.1405) 204.79
TOTAL 1662.39 Y
Add 15% CPOH on "Y" 249.36
TOTAL 1911.74 Z
Add Cess @ 1% on "Z" 19.12
Cost of each 1930.86
Say 1930.85
17.19.2 10 litre (full flush) capacity-coloured
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7127 Coloured Vitreous china 10 lit. (full
flush) capacity controlled low level
flushing cistern with all fittings each 1.00 1150.00 1150.00
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1893.16 W
Add 1 % Water charges on "W" 18.93
TOTAL 1912.09 X
Add GST on "X" (multiplying
factor 0.1405) 268.65
TOTAL 2180.74 Y
Add 15% CPOH on "Y" 327.11
TOTAL 2507.85 Z
Add Cess @ 1% on "Z" 25.08
Cost of each 2532.93
Say 2532.95
SUB HEAD : 17- SANITARY INSTALLATIONS 1389
17.20 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan
complete :
17.20.1 White solid plastic seat with lid
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1875 White plastic seat (solid)with lid
C.P.brass hinges and rubber buffers each 1.00 410.00 410.00
9988 Carriage of materials and fixing charges L.S. 13.39 2.12 28.39
TOTAL 438.39 W
Add 1 % Water charges on "W" 4.38
TOTAL 442.77 X
Add GST on "X" (multiplying
factor 0.1405) 62.21
TOTAL 504.98 Y
Add 15% CPOH on "Y" 75.75
TOTAL 580.73 Z
Add Cess @ 1% on "Z" 5.81
Cost of each 586.53
Say 586.55
17.20.2 Black solid plastic seat with lid
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1876 Black plastic seat (solid) with lid
C.P.brass hinges and rubber buffers each 1.00 325.00 325.00
9988 Carriage of materials and fixing charges L.S. 13.39 2.12 28.39
TOTAL 353.39 W
Add 1 % Water charges on "W" 3.53
TOTAL 356.92 X
Add GST on "X" (multiplying
factor 0.1405) 50.15
TOTAL 407.07 Y
Add 15% CPOH on "Y" 61.06
TOTAL 468.13 Z
Add Cess @ 1% on "Z" 4.68
Cost of each 472.81
Say 472.80
17.20.3 Coloured (other than black & white) solid plastic seat with lid
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
Difference in cost of
7107 Coloured (other than black) solid
P.V.C. seat in European W.C. pan each 1.00 350.00 350.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1390
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.39 2.12 28.39
TOTAL 378.39 W
Add 1 % Water charges on "W" 3.78
TOTAL 382.17 X
Add GST on "X" (multiplying
factor 0.1405) 53.69
TOTAL 435.87 Y
Add 15% CPOH on "Y" 65.38
TOTAL 501.25 Z
Add Cess @ 1% on "Z" 5.01
Cost of each 506.26
Say 506.25
17.22 Providing and fixing G.I. inlet connection for flush pipe connecting with W.C.
pan.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1614 G.I. inlet connection each 1.00 70.00 70.00
9988 Carriage of materials and fixing charges L.S. 13.39 2.12 28.39
TOTAL 98.39 W
Add 1 % Water charges on "W" 0.98
TOTAL 99.37 X
Add GST on "X" (multiplying
factor 0.1405) 13.96
TOTAL 113.33 Y
Add 15% CPOH on "Y" 17.00
TOTAL 130.33 Z
Add Cess @ 1% on "Z" 1.30
Cost of each 131.64
Say 131.65
17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved quality &
make and as per the direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7121 Bottle Trap each 1.00 620.00 620.00
9988 Carriage and sundries L.S. 20.00 2.12 42.40
TOTAL 662.40 W
Add 1 % Water charges on "W" 6.62
TOTAL 669.02 X
Add GST on "X" (multiplying
factor 0.1405) 94.00
TOTAL 763.02 Y
Add 15% CPOH on "Y" 114.45
TOTAL 877.48 Z
Add Cess @ 1% on "Z" 8.77
Cost of each 886.25
Say 886.25
SUB HEAD : 17- SANITARY INSTALLATIONS 1391
17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of quality &
make as approved by Engineer in charge.
(a) 15 mm nominal dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7122 CP Brass Single lever telephonic wall
mixer of approved make each 1.00 4500.00 4500.00
9977 Carriage of material and fixing charges L.S. 34.71 2.12 73.59
TOTAL 4573.59 W
Add 1 % Water charges on "W" 45.74
TOTAL 4619.32 X
Add GST on "X" (multiplying
factor 0.1405) 649.01
TOTAL 5268.34 Y
Add 15% CPOH on "Y" 790.25
TOTAL 6058.59 Z
Add Cess @ 1% on "Z" 60.59
Cost of each 6119.17
Say 6119.15
17.23 Providing and fixing white vitreous china flat back or wall corner type lipped
front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1913 Vitreous china lipped front urinal each 1.00 470.00 470.00
9977 Carriage of materials L.S. 9.49 2.12 20.12
LABOUR
0116 Fitter (grade 1) day 0.38 784.00 297.92
0114 Beldar day 0.38 645.00 245.10
TOTAL 1033.14 W
Add 1 % Water charges on "W" 10.33
TOTAL 1043.47 X
Add GST on "X" (multiplying
factor 0.1405) 146.61
TOTAL 1190.08 Y
Add 15% CPOH on "Y" 178.51
TOTAL 1368.59 Z
Add Cess @ 1% on "Z" 13.69
Cost of each 1382.28
Say 1382.30
17.24 Providing and fixing white vitreous china squatting plate urinal with integral
rim longitudinal flush pipe.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1915 Vitreous china squatting plate urinal each 1.00 1053.00 1053.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1392
Code Description Unit Quantity Rate Amount
9999 Cement, sand and grit etc. L.S. 10.79 2.12 22.87
9977 Carriage of materials L.S. 13.39 2.12 28.39
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 2533.26 W
Add 1 % Water charges on "W" 25.33
TOTAL 2558.59 X
Add GST on "X" (multiplying
factor 0.1405) 359.48
TOTAL 2918.08 Y
Add 15% CPOH on "Y" 437.71
TOTAL 3355.79 Z
Add Cess @ 1% on "Z" 33.56
Cost of each 3389.35
Say 3389.35
17.25 Providing and fixing white vitreous china wash basin including making all
connections but excluding the cost of fittings :
17.25.1 Flat back wash basin of size 630x450 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1947 Vitreous china flat back wash basin
630x450 mm each 1.00 725.00 725.00
9999 Fixing charges L.S. 53.82 2.12 114.10
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 859.22 W
Add 1 % Water charges on "W" 8.59
TOTAL 867.81 X
Add GST on "X" (multiplying
factor 0.1405) 121.93
TOTAL 989.74 Y
Add 15% CPOH on "Y" 148.46
TOTAL 1138.20 Z
Add Cess @ 1% on "Z" 11.38
Cost of each 1149.58
Say 1149.60
17.25.2 Flat back wash basin of size 550x400 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3229 Vitreous china flat back wash basin
550x400 mm each 1.00 550.00 550.00
9999 Fixing charges L.S. 53.82 2.12 114.10
SUB HEAD : 17- SANITARY INSTALLATIONS 1393
Code Description Unit Quantity Rate Amount
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 684.22 W
Add 1 % Water charges on "W" 6.84
TOTAL 691.06 X
Add GST on "X" (multiplying
factor 0.1405) 97.09
TOTAL 788.15 Y
Add 15% CPOH on "Y" 118.22
TOTAL 906.38 Z
Add Cess @ 1% on "Z" 9.06
Cost of each 915.44
Say 915.45
17.25.3 Angle back wash basin of size 600x480 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1949 Vitreous china angle back wash basin
600x480 mm each 1.00 725.00 725.00
9999 Fixing charges L.S. 53.82 2.12 114.10
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 859.22 W
Add 1 % Water charges on "W" 8.59
TOTAL 867.81 X
Add GST on "X" (multiplying
factor 0.1405) 121.93
TOTAL 989.74 Y
Add 15% CPOH on "Y" 148.46
TOTAL 1138.20 Z
Add Cess @ 1% on "Z" 11.38
Cost of each 1149.58
Say 1149.60
17.25.4 Angle back wash basin of size 400x400 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1950 Vitreous china angle back wash
basin 400x400 mm each 1.00 425.00 425.00
9999 Fixing charges L.S. 53.82 2.12 114.10
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 559.22 W
Add 1 % Water charges on "W" 5.59
TOTAL 564.81 X
Add GST on "X" (multiplying
factor 0.1405) 79.36
TOTAL 644.17 Y
Add 15% CPOH on "Y" 96.62
TOTAL 740.79 Z
Add Cess @ 1% on "Z" 7.41
Cost of each 748.20
Say 748.20
SUB HEAD : 17- SANITARY INSTALLATIONS 1394
17.25.5 Flat back wash basin of size 450x300 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7004 Vitreous china flat back wash basin
450x300 mm each 1.00 280.00 280.00
9999 Fixing charges L.S. 53.82 2.12 114.10
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 414.22 W
Add 1 % Water charges on "W" 4.14
TOTAL 418.36 X
Add GST on "X" (multiplying
factor 0.1405) 58.78
TOTAL 477.14 Y
Add 15% CPOH on "Y" 71.57
TOTAL 548.71 Z
Add Cess @ 1% on "Z" 5.49
Cost of each 554.20
Say 554.20
17.25.6 Surgeon type wash basin of size 660x460 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3213 Vitreous china Surgeon type wash
basin of size 660x460 mm each 1.00 1100.00 1100.00
9999 Fixing charges L.S. 53.82 2.12 114.10
9977 Carriage of materials L.S. 9.49 2.12 20.12
TOTAL 1234.22 W
Add 1 % Water charges on "W" 12.34
TOTAL 1246.56 X
Add GST on "X" (multiplying
factor 0.1405) 175.14
TOTAL 1421.70 Y
Add 15% CPOH on "Y" 213.26
TOTAL 1634.96 Z
Add Cess @ 1% on "Z" 16.35
Cost of each 1651.31
Say 1651.30
17.26 Providing and fixing kitchen sink including making all connections excluding
cost of fittings.
17.26.1 White glazed fire clay sink of size 600x450x250 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1863 Fire clay kitchen sink: 600x450x250 mm each 1.00 1300.00 1300.00
9999 Fixing charges L.S. 40.43 2.12 85.71
SUB HEAD : 17- SANITARY INSTALLATIONS 1395
Code Description Unit Quantity Rate Amount
9977 Carriage of materials L.S. 10.79 2.12 22.87
TOTAL 1408.59 W
Add 1 % Water charges on "W" 14.09
TOTAL 1422.67 X
Add GST on "X" (multiplying
factor 0.1405) 199.89
TOTAL 1622.56 Y
Add 15% CPOH on "Y" 243.38
TOTAL 1865.94 Z
Add Cess @ 1% on "Z" 18.66
Cost of each 1884.60
Say 1884.60
17.27 Providing and fixing white vitreous china laboratory sink including making all
connections excluding cost of fittings :
17.27.1 Size 450x300x150 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1871 White vitreous china laboratry sink
450x300x150 mm each 1.00 1500.00 1500.00
9999 Fixing charges L.S. 40.43 2.12 85.71
9977 Carriage of materials L.S. 10.79 2.12 22.87
TOTAL 1608.59 W
Add 1 % Water charges on "W" 16.09
TOTAL 1624.67 X
Add GST on "X" (multiplying
factor 0.1405) 228.27
TOTAL 1852.94 Y
Add 15% CPOH on "Y" 277.94
TOTAL 2130.88 Z
Add Cess @ 1% on "Z" 21.31
Cost of each 2152.19
Say 2152.20
17.27.2 Size 600x450x200 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1872 White vitreous china laboratry sink
600x450x200 mm each 1.00 2500.00 2500.00
9999 Fixing charges L.S. 40.43 2.12 85.71
SUB HEAD : 17- SANITARY INSTALLATIONS 1396
Code Description Unit Quantity Rate Amount
9977 Carriage of materials L.S. 10.79 2.12 22.87
TOTAL 2608.59 W
Add 1 % Water charges on "W" 26.09
TOTAL 2634.67 X
Add GST on "X" (multiplying
factor 0.1405) 370.17
TOTAL 3004.84 Y
Add 15% CPOH on "Y" 450.73
TOTAL 3455.57 Z
Add Cess @ 1% on "Z" 34.56
Cost of each 3490.13
Say 3490.15
17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.
waste fittings complete.
17.28.1 Semi rigid pipe
17.28.1.1 32 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7117 Semi Rigid PVC waste pipe for sink
and wash basin 32 mm dia with length
not less than 700 mm i/c PVC waste
fittings each 1.00 25.00 25.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 67.99 W
Add 1 % Water charges on "W" 0.68
TOTAL 68.67 X
Add GST on "X" (multiplying
factor 0.1405) 9.65
TOTAL 78.32 Y
Add 15% CPOH on "Y" 11.75
TOTAL 90.07 Z
Add Cess @ 1% on "Z" 0.90
Cost of each 90.97
Say 90.95
17.28.1.2 40 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7118 Semi Rigid PVC waste pipe for sink
and wash basin 40 mm dia with length
not less than 700 mm i/c PVC waste
fittings each 1.00 33.00 33.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1397
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 75.99 W
Add 1 % Water charges on "W" 0.76
TOTAL 76.75 X
Add GST on "X" (multiplying
factor 0.1405) 10.78
TOTAL 87.54 Y
Add 15% CPOH on "Y" 13.13
TOTAL 100.67 Z
Add Cess @ 1% on "Z" 1.01
Cost of each 101.67
Say 101.65
17.28.2 Flexible pipe
17.28.2.1 32 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7119 Flexible (coil shaped) PVC waste pipe
for sink and wash basin 32 mm dia
with length not less than 700 mm i/c
PVC waste fittings each 1.00 35.00 35.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 77.99 W
Add 1 % Water charges on "W" 0.78
TOTAL 78.77 X
Add GST on "X" (multiplying
factor 0.1405) 11.07
TOTAL 89.84 Y
Add 15% CPOH on "Y" 13.48
TOTAL 103.32 Z
Add Cess @ 1% on "Z" 1.03
Cost of each 104.35
Say 104.35
17.28.2.2 40 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7120 Flexible (coil shaped) PVC waste pipe
for sink and wash basin 40 mm dia
with length not less than 700 mm i/c
PVC waste fittings each 1.00 35.00 35.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1398
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 77.99 W
Add 1 % Water charges on "W" 0.78
TOTAL 78.77 X
Add GST on "X" (multiplying
factor 0.1405) 11.07
TOTAL 89.84 Y
Add 15% CPOH on "Y" 13.48
TOTAL 103.32 Z
Add Cess @ 1% on "Z" 1.03
Cost of each 104.35
Say 104.35
17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1369 S.C.I. gully or nahani grating 100 mm dia each 1.00 25.00 25.00
9988 Carriage of materials and fixing charges L.S. 4.16 2.12 8.82
TOTAL 33.82 W
Add 1 % Water charges on "W" 0.34
TOTAL 34.16 X
Add GST on "X" (multiplying
factor 0.1405) 4.80
TOTAL 38.96 Y
Add 15% CPOH on "Y" 5.84
TOTAL 44.80 Z
Add Cess @ 1% on "Z" 0.45
Cost of each 45.25
Say 45.25
17.30 Providing and fixing in position 25 mm diameter mosquito proof coupling of
approved municipal design.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1350 Mosquito proof coupling of approved
design each 1.00 30.00 30.00
9988 Carriage of materials and fixing charges L.S. 1.82 2.12 3.86
TOTAL 33.86 W
Add 1 % Water charges on "W" 0.34
TOTAL 34.20 X
Add GST on "X" (multiplying
factor 0.1405) 4.80
TOTAL 39.00 Y
Add 15% CPOH on "Y" 5.85
TOTAL 44.85 Z
Add Cess @ 1% on "Z" 0.45
Cost of each 45.30
Say 45.30
SUB HEAD : 17- SANITARY INSTALLATIONS 1399
17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of
approved quality) complete with 6 mm thick hard board ground fixed to wooden
cleats with C.P. brass screws and washers complete.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1392 Mirror of superior make glass 60x45 cm each 1.00 450.00 450.00
7116 Hard board 6 mm thick sqm 0.27 115.00 31.05
600x450 mm Wooden cleats
8.23 Rate as per item no 8.23 of
SH : Cladding work each 4.00 35.50 142.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.04 180.00 7.20
9977 Carriage of materials L.S. 4.16 2.12 8.82
9999 Sundries L.S. 1.43 2.12 3.03
LABOUR
0112 Carpenter 2nd class day 0.33 714.00 235.62
0114 Beldar day 0.33 645.00 212.85
TOTAL 1090.57 W
Add 1 % Water charges on "W-A" 9.49
TOTAL 1100.06 X
Add GST on "X-A" (multiplying
factor 0.1405) 134.61
TOTAL 1234.66 Y
Add 15% CPOH on "Y-A" 163.90
TOTAL 1398.56 Z
Add Cess @ 1% on "Z-A" 12.57
Cost of each 1411.13
Say 1411.15
17.32 Providing and fixing mirror of superior glass (of approved quality) and of
required shape and size with plastic moulded frame of approved make and
shade with 6 mm thick hard board backing :
17.32.1 Circular shape 450 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7112 Circular shape 450 mm dia Mirror with
Plastic moulded frame each 1.00 400.00 400.00
Hard board 0.45x0.45 = 0.2025 sqm
Add wastage @ 10% = 0.0203 sqm
= 0.2228 sqm say 0.22sqm
7116 Hard board 6 mm thick sqm 0.22 115.00 25.30
7048 Rawl plug 50 mm (designation 10 no.) each 2.00 22.00 44.00
0588 Chromium plated Brass screws 25 mm 100 Nos 0.02 180.00 3.60
9999 Sundries L.S. 1.43 2.12 3.03
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.33 714.00 235.62
SUB HEAD : 17- SANITARY INSTALLATIONS 1400
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.33 645.00 212.85
TOTAL 933.22 W
Add 1 % Water charges on "W" 9.33
TOTAL 942.55 X
Add GST on "X" (multiplying
factor 0.1405) 132.43
TOTAL 1074.98 Y
Add 15% CPOH on "Y" 161.25
TOTAL 1236.23 Z
Add Cess @ 1% on "Z" 12.36
Cost of each 1248.59
Say 1248.60
17.32.2 Rectangular shape 453x357 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7113 Rectangular shape 453x357 mm
Mirror with Plastic moulded frame each 1.00 290.00 290.00
Hard board 0.453x0.357 = 0.1617 sqm
Add wastage @ 10% = 0.0162 sqm
= 0.1779 sqm say 0.18 sqm
7116 Hard board 6 mm thick sqm 0.18 115.00 20.70
7048 Rawl plug 50 mm (designation 10 no.) each 4.00 22.00 88.00
0588 Chromium plated Brass screws 25 mm 100 Nos 0.04 180.00 7.20
9999 Sundries L.S. 1.43 2.12 3.03
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.33 714.00 235.62
0114 Beldar day 0.33 645.00 212.85
TOTAL 866.22 W
Add 1 % Water charges on "W" 8.66
TOTAL 874.88 X
Add GST on "X" (multiplying
factor 0.1405) 122.92
TOTAL 997.80 Y
Add 15% CPOH on "Y" 149.67
TOTAL 1147.47 Z
Add Cess @ 1% on "Z" 11.47
Cost of each 1158.95
Say 1158.95
17.32.3 Oval shape 450x350 mm (outer dimensions)
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7114 Ovel shape 450x350 mm (outer
dimensions) Mirror with Plastic
moulded frame each 1.00 290.00 290.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1401
Code Description Unit Quantity Rate Amount
Hard board 0.45x0.35=0.1575 sqm
Add wastage @ 10% = 0.0158 sqm
= 0.1733 sqm say 0.17 sqm
7116 Hard board 6 mm thick sqm 0.17 115.00 19.55
7048 Rawl plug 50 mm (designation 10 no.) each 4.00 22.00 88.00
0588 Chromium plated Brass screws 25 mm 100 Nos 0.04 180.00 7.20
9999 Sundries L.S. 1.43 2.12 3.03
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.33 714.00 235.62
0114 Beldar day 0.33 645.00 212.85
TOTAL 865.07 W
Add 1 % Water charges on "W" 8.65
TOTAL 873.72 X
Add GST on "X" (multiplying
factor 0.1405) 122.76
TOTAL 996.48 Y
Add 15% CPOH on "Y" 149.47
TOTAL 1145.95 Z
Add Cess @ 1% on "Z" 11.46
Cost of each 1157.41
Say 1157.40
17.32.4 Rectangular shape 1500x450 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7115 Rectangular shape 1500x450 mm
Mirror with Plastic moulded frame each 1.00 670.00 670.00
Hard board 1.50x0.45 = 0.675 sqm
Add wastage @ 10% = 0.0675 sqm
= 0.7425 sqm say 0.74sqm
7116 Hard board 6 mm thick sqm 0.74 115.00 85.10
7048 Rawl plug 50 mm (designation 10 no.) each 6.00 22.00 132.00
0588 Chromium plated Brass screws 25 mm 100 Nos 0.06 180.00 10.80
9999 Sundries L.S. 1.43 2.12 3.03
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.33 714.00 235.62
0114 Beldar day 0.33 645.00 212.85
TOTAL 1358.22 W
Add 1 % Water charges on "W" 13.58
TOTAL 1371.80 X
Add GST on "X" (multiplying
factor 0.1405) 192.74
TOTAL 1564.54 Y
Add 15% CPOH on "Y" 234.68
TOTAL 1799.22 Z
Add Cess @ 1% on "Z" 17.99
Cost of each 1817.21
Say 1817.20
SUB HEAD : 17- SANITARY INSTALLATIONS 1402
17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off, supported
on anodised aluminium angle frame with C.P. brass brackets and guard rail
complete fixed with 40 mm long screws, rawl plugs etc., complete.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3228 600x120 mm glass shelf with anodised
aluminium angle frame, C.P. brass
brackets and guard rail of standard
size each 1.00 300.00 300.00
7048 Rawl plug 50 mm (designation 10 no.) each 2.00 22.00 44.00
0586 Chromium plated Brass screws 40 mm 100 Nos 0.04 290.00 11.60
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
TOTAL 704.17 W
Add 1 % Water charges on "W" 7.04
TOTAL 711.21 X
Add GST on "X" (multiplying
factor 0.1405) 99.93
TOTAL 811.14 Y
Add 15% CPOH on "Y" 121.67
TOTAL 932.81 Z
Add Cess @ 1% on "Z" 9.33
Cost of each 942.13
Say 942.15
17.34 Providing and fixing toilet paper holder :
17.34.1 C.P. brass
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1889 C.P.brass toilet paper holder of
standard size each 1.00 280.00 280.00
Wooden cleats
8.23 Rate as per item no 8.23 of
SH : Cladding work each 2.00 35.50 71.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.02 180.00 3.60
9977 Carriage of materials L.S. 4.29 2.12 9.09
LABOUR
0112 Carpenter 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.12 645.00 77.40
TOTAL 526.77 W
Add 1 % Water charges on "W-A" 4.56
TOTAL 531.33 X
Add GST on "X-A" (multiplying
factor 0.1405) 64.68
TOTAL 596.01 Y
Add 15% CPOH on "Y-A" 78.75
TOTAL 674.76 Z
Add Cess @ 1% on "Z-A" 6.04
Cost of each 680.80
Say 680.80
SUB HEAD : 17- SANITARY INSTALLATIONS 1403
17.34.2 Vitreous china
Code Description Unit Quantity Rate Amount
Details of cost of one no.
MATERIAL
3749 Vitreous china toilet paper holder of
standard size each 1.00 110.00 110.00
Wooden cleats
8.23 Rate as per item no 8.23 of
SH : Cladding work each 2.00 35.50 71.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.06 180.00 10.80
9977 Carriage of materials L.S. 4.29 2.12 9.09
LABOUR
0112 Carpenter 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.12 645.00 77.40
TOTAL 363.97 W
Add 1 % Water charges on "W-A" 2.93
TOTAL 366.90 X
Add GST on "X-A" (multiplying
factor 0.1405) 41.57
TOTAL 408.48 Y
Add 15% CPOH on "Y-A" 50.62
TOTAL 459.10 Z
Add Cess @ 1% on "Z-A" 3.88
Cost of each 462.98
Say 463.00
17.35 Providing and fixing soil, waste and vent pipes :
17.35.1 100 mm dia
17.35.1.1 Sand cast iron S&S pipe as per IS: 1729
Code Description Unit Quantity Rate Amount
Details of cost for 17.37 m
(1.8mx10)-(9x0.07m) = 17.37 m
MATERIAL
1617 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
100mm dia each 10.50 1135.00 11917.50
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 53.82 2.12 114.10
LABOUR
0116 Fitter (grade 1) day 0.42 784.00 329.28
0100 Bandhani day 0.21 714.00 149.94
0114 Beldar day 0.83 645.00 535.35
TOTAL 13217.32 W
Add 1 % Water charges on "W" 132.17
TOTAL 13349.49 X
Add GST on "X" (multiplying
factor 0.1405) 1875.60
TOTAL 15225.09 Y
Add 15% CPOH on "Y" 2283.76
TOTAL 17508.86 Z
Add Cess @ 1% on "Z" 175.09
Cost for 17.37 m pan 17683.94
Cost per metre 1018.07
Say 1018.05
SUB HEAD : 17- SANITARY INSTALLATIONS 1404
17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
Code Description Unit Quantity Rate Amount
Details of cost for 16.87 m
(1.75mx10)-(9x0.07m) = 16.87 m
MATERIAL
3620 C.C.I.(spun) socketed soil, waste and
vent pipe 1.80 metres long:100mm dia each 10.50 1170.00 12285.00
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 53.82 2.12 114.10
LABOUR
0116 Fitter (grade 1) day 0.42 784.00 329.28
0100 Bandhani day 0.21 714.00 149.94
0114 Beldar day 0.83 645.00 535.35
TOTAL 13584.82 W
Add 1 % Water charges on "W" 135.85
TOTAL 13720.66 X
Add GST on "X" (multiplying
factor 0.1405) 1927.75
TOTAL 15648.42 Y
Add 15% CPOH on "Y" 2347.26
TOTAL 17995.68 Z
Add Cess @ 1% on "Z" 179.96
Cost for 16.87 m pan 18175.64
Cost per metre 1077.39
Say 1077.40
17.35.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for 18.00 m (6 x 3.00 m)
MATERIAL
7621 Hubless centrifugally cast (spun) iron
pipes as per IS 15905 - 100 mm dia
(3000 mm length pipe) metre 18.54 700.00 12978.00
i/c (3% wastage)
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 53.82 2.12 114.10
LABOUR
0116 Fitter (grade 1) day 0.42 784.00 329.28
0100 Bandhani day 0.21 714.00 149.94
0114 Beldar day 0.83 645.00 535.35
TOTAL 14277.82 W
Add 1 % Water charges on "W" 142.78
TOTAL 14420.59 X
Add GST on "X" (multiplying
factor 0.1405) 2026.09
TOTAL 16446.69 Y
Add 15% CPOH on "Y" 2467.00
TOTAL 18913.69 Z
Add Cess @ 1% on "Z" 189.14
Cost of 18.00 metre 19102.83
Cost of 1 metre 1061.27
Say 1061.25
SUB HEAD : 17- SANITARY INSTALLATIONS 1405
17.35.2 75 mm diameter :
17.35.2.1 Sand cast iron S&S pipe as per IS: 1729
Code Description Unit Quantity Rate Amount
Details of cost for 17.42 m
(1.8mx10)-(9x0.065m) = 17.415 m
say 17.42 m
MATERIAL
1616 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
75mm dia each 10.50 1050.00 11025.00
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 40.38 2.12 85.61
LABOUR
0116 Fitter (grade 1) day 0.35 784.00 274.40
0100 Bandhani day 0.17 714.00 121.38
0114 Beldar day 0.70 645.00 451.50
TOTAL 12129.03 W
Add 1 % Water charges on "W" 121.29
TOTAL 12250.32 X
Add GST on "X" (multiplying
factor 0.1405) 1721.17
TOTAL 13971.49 Y
Add 15% CPOH on "Y" 2095.72
TOTAL 16067.22 Z
Add Cess @ 1% on "Z" 160.67
Cost for 17.42 m pan 16227.89
Cost per metre 931.57
Say 931.55
17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989
Code Description Unit Quantity Rate Amount
Details of cost for 16.92 m
(1.75mx10)-(9x0.065m) = 16.915 m.
say 16.92 m
MATERIAL
3621 C.C.I.(spun) socketed soil, waste and
vent pipe 1.80 metres long:75mm dia each 10.50 1150.00 12075.00
including 5% allowance for wastage
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 40.38 2.12 85.61
LABOUR
0116 Fitter (grade 1) day 0.35 784.00 274.40
0100 Bandhani day 0.17 714.00 121.38
0114 Beldar day 0.70 645.00 451.50
TOTAL 13179.03 W
Add 1 % Water charges on "W" 131.79
TOTAL 13310.82 X
Add GST on "X" (multiplying
factor 0.1405) 1870.17
TOTAL 15180.99 Y
Add 15% CPOH on "Y" 2277.15
TOTAL 17458.14 Z
Add Cess @ 1% on "Z" 174.58
Cost for 16.92 m pan 17632.72
Cost per metre 1042.12
Say 1042.10
SUB HEAD : 17- SANITARY INSTALLATIONS 1406
17.35.2.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for 18.00 m (6 x 3.00 m)
MATERIAL
7622 Hubless centrifugally cast (spun) iron
pipes as per IS 15905 - 75 mm dia
(3000 mm length pipe) metre 18.54 570.00 10567.80
i/c (3% wastage)
9999 Scaffolding L.S. 80.73 2.12 171.15
9977 Carriage of materials L.S. 40.38 2.12 85.61
LABOUR
0116 Fitter (grade 1) day 0.35 784.00 274.40
0100 Bandhani day 0.17 714.00 121.38
0114 Beldar day 0.70 645.00 451.50
TOTAL 11671.83 W
Add 1 % Water charges on "W" 116.72
TOTAL 11788.55 X
Add GST on "X" (multiplying
factor 0.1405) 1656.29
TOTAL 13444.84 Y
Add 15% CPOH on "Y" 2016.73
TOTAL 15461.57 Z
Add Cess @ 1% on "Z" 154.62
Cost of 18.00 metre 15616.19
Cost of 1 metre 867.57
Say 867.55
17.36 Providing and filling the joints with spun yarn, cement slurry and cement mortar
1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :
17.36.1 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 4 joints
MATERIAL
9999 Cement mortar, spun yarn etc. L.S. 6.89 2.12 14.61
LABOUR
0116 Fitter (grade 1) day 0.28 784.00 219.52
0114 Beldar day 0.28 645.00 180.60
TOTAL 414.73 W
Add 1 % Water charges on "W" 4.15
TOTAL 418.87 X
Add GST on "X" (multiplying
factor 0.1405) 58.85
TOTAL 477.73 Y
Add 15% CPOH on "Y" 71.66
TOTAL 549.38 Z
Add Cess @ 1% on "Z" 5.49
Cost of 4 joints 554.88
Cost of 1 joint 138.72
Say 138.70
SUB HEAD : 17- SANITARY INSTALLATIONS 1407
17.36.2 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 4 joints
MATERIAL
9999 Cement mortar, spun yarn etc. L.S. 8.06 2.12 17.09
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 488.66 W
Add 1 % Water charges on "W" 4.89
TOTAL 493.54 X
Add GST on "X" (multiplying
factor 0.1405) 69.34
TOTAL 562.89 Y
Add 15% CPOH on "Y" 84.43
TOTAL 647.32 Z
Add Cess @ 1% on "Z" 6.47
Cost of 4 joints 653.79
Cost of 1 joint 163.45
Say 163.45
17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast
iron/cast iron (spun) pipe embedded in and including cement concrete blocks
10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size), including cost of cutting holes and making good the
walls etc. :
17.37.1 For 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 nos.
MATERIAL
1331 M.S.Holder bat clamp of approved
design for 100 mm S.C.I. pipe each 5.00 30.00 150.00
9977 Carriage of bat clamps L.S. 2.47 2.12 5.24
LABOUR
0116 Fitter (grade 1) day 0.125 784.00 98.00
0124 Mason (brick layer) 2nd class day 0.75 714.00 535.50
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 7.15 2.12 15.16
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.0033 1400.00 4.62
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.0011 1350.00 1.49
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.0044 163.93 0.72
0982 Coarse sand (zone III) cum 0.0022 1500.00 3.30
2203 Carriage of Coarse sand cum 0.0022 163.93 0.36
0367 Portland Cement (OPC-43 grade) tonne 0.0016 5000.00 8.00
2209 Carriage of Cement tonne 0.0016 145.72 0.23
0114 Beldar day 0.0045 645.00 2.90
0115 Coolie day 0.0032 645.00 2.06
0101 Bhisti day 0.0014 714.00 1.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1408
Code Description Unit Quantity Rate Amount
0123 Mason (brick layer) 1st class day 0.0003 784.00 0.24
0124 Mason (brick layer) 2nd class day 0.0003 714.00 0.21
0128 Mate day 0.0002 714.00 0.14
9999 Hire charges of machine etc. L.S. 0.26 2.12 0.55
9999 Sundries L.S. 0.13 2.12 0.28
9999 Sundries L.S. 0.13 2.12 0.28
TOTAL 1152.78 W
Add 1 % Water charges on "W" 11.53
TOTAL 1164.30 X
Add GST on "X" (multiplying
factor 0.1405) 163.58
TOTAL 1327.89 Y
Add 15% CPOH on "Y" 199.18
TOTAL 1527.07 Z
Add Cess @ 1% on "Z" 15.27
Cost of 5.00 bat clamps 1542.34
Cost of each 308.47
Say 308.45
17.37.2 For 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 nos.
MATERIAL
1332 M.S.Holder bat clamp of approved
design for75 mm S.C.I. pipe each 5.00 27.00 135.00
9977 Carriage of bat clamps L.S. 2.47 2.12 5.24
LABOUR
0116 Fitter (grade 1) day 0.125 784.00 98.00
0124 Mason (brick layer) 2nd class day 0.75 714.00 535.50
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 7.15 2.12 15.16
C.C. Black 5x0.1x0.1x0.1 = 0.005 cum
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.0033 1400.00 4.62
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.0011 1350.00 1.49
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.0044 163.93 0.72
0982 Coarse sand (zone III) cum 0.0022 1500.00 3.30
2203 Carriage of Coarse sand cum 0.0022 163.93 0.36
0367 Portland Cement (OPC-43 grade) tonne 0.0016 5000.00 8.00
2209 Carriage of Cement tonne 0.0016 145.72 0.23
0114 Beldar day 0.0045 645.00 2.90
0115 Coolie day 0.0032 645.00 2.06
0101 Bhisti day 0.0014 714.00 1.00
0123 Mason (brick layer) 1st class day 0.0003 784.00 0.24
0124 Mason (brick layer) 2nd class day 0.0003 714.00 0.21
0128 Mate day 0.0002 714.00 0.14
9999 Hire charges of machine etc. L.S. 0.26 2.12 0.55
9999 Sundries L.S. 0.13 2.12 0.28
SUB HEAD : 17- SANITARY INSTALLATIONS 1409
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 0.13 2.12 0.28
TOTAL 1137.78 W
Add 1 % Water charges on “W” 11.38
TOTAL 1149.15 X
Add GST on “X” (multiplying
factor 0.1405) 161.46
TOTAL 1310.61 Y
Add 15% CPOH on “Y” 196.59
TOTAL 1507.20 Z
Add Cess @ 1% on “Z” 15.07
Cost of 5.00 bat clamps 1522.27
Cost of each 304.45
Say 304.45
17.38 Providing and fixing bend of required degree with access door, insertion rubber
washer 3 mm thick, bolts and nuts complete.
17.38.1 100 mm dia
17.38.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1625 S.C.I. bend with access door 100mm dia each 1.00 350.00 350.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 396.66 W
Add 1 % Water charges on "W" 3.97
TOTAL 400.63 X
Add GST on "X" (multiplying
factor 0.1405) 56.29
TOTAL 456.92 Y
Add 15% CPOH on "Y" 68.54
TOTAL 525.46 Z
Add Cess @ 1% on "Z" 5.25
Cost of each 530.71
Say 530.70
17.38.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3624 S.C.I. S&S bends with access door
100mm dia each 1.00 400.00 400.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1410
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 446.66 W
Add 1 % Water charges on "W" 4.47
TOTAL 451.13 X
Add GST on "X" (multiplying
factor 0.1405) 63.38
TOTAL 514.51 Y
Add 15% CPOH on "Y" 77.18
TOTAL 591.69 Z
Add Cess @ 1% on "Z" 5.92
Cost of each 597.61
Say 597.60
17.38.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7639 Hubless centrifugally cast (spun) iron
bend with access door - 100 mm dia as
per IS IS:15905 each 1.00 365.00 365.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9977 Carriage of materials and fixing
charges L.S. 13.52 2.12 28.66
TOTAL 411.66 W
Add 1 % Water charges on "W" 4.12
TOTAL 415.78 X
Add GST on "X" (multiplying
factor 0.1405) 58.42
TOTAL 474.20 Y
Add 15% CPOH on "Y" 71.13
TOTAL 545.33 Z
Add Cess @ 1% on "Z" 5.45
Cost of each 550.78
Say 550.80
17.38.2 75 mm dia
17.38.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1624 S.C.I. bend with access door 75mm dia each 1.00 290.00 290.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1411
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 328.87 W
Add 1 % Water charges on "W" 3.29
TOTAL 332.16 X
Add GST on "X" (multiplying
factor 0.1405) 46.67
TOTAL 378.83 Y
Add 15% CPOH on "Y" 56.82
TOTAL 435.66 Z
Add Cess @ 1% on "Z" 4.36
Cost of each 440.01
Say 440.00
17.38.2.2 Sand cast iron S&S as per IS- 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3625 S.C.I. S&S bends with access
door75mm dia each 1.00 300.00 300.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
9988 Carriage of materials and fixing
charges L.S. 10.79 2.12 22.87
TOTAL 338.87 W
Add 1 % Water charges on "W" 3.39
TOTAL 342.26 X
Add GST on "X" (multiplying
factor 0.1405) 48.09
TOTAL 390.35 Y
Add 15% CPOH on "Y" 58.55
TOTAL 448.90 Z
Add Cess @ 1% on "Z" 4.49
Cost of each 453.39
Say 453.40
17.38.2.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7640 Hubless centrifugally cast (spun) iron
bend with access door - 75 mm dia as
per IS 15905 including cost of bolts &
nuts. each 1.00 290.00 290.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
3mm thick
SUB HEAD : 17- SANITARY INSTALLATIONS 1412
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 328.87 W
Add 1 % Water charges on "W" 3.29
TOTAL 332.16 X
Add GST on "X" (multiplying
factor 0.1405) 46.67
TOTAL 378.83 Y
Add 15% CPOH on "Y" 56.82
TOTAL 435.66 Z
Add Cess @ 1% on "Z" 4.36
Cost of each 440.01
Say 440.00
17.39 Providing and fixing plain bend of required degree.
17.39.1 100 mm dia
17.39.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1621 S.C.I. plain bend 100 mm dia each 1.00 280.00 280.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 308.66 W
Add 1 % Water charges on "W" 3.09
TOTAL 311.75 X
Add GST on "X" (multiplying
factor 0.1405) 43.80
TOTAL 355.55 Y
Add 15% CPOH on "Y" 53.33
TOTAL 408.88 Z
Add Cess @ 1% on "Z" 4.09
Cost of each 412.97
Say 412.95
17.39.1.2 Sand cast iron S&S as per IS : 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3628 S.C.I. S&S bend100mm dia each 1.00 300.00 300.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 328.66 W
Add 1 % Water charges on "W" 3.29
TOTAL 331.95 X
Add GST on "X" (multiplying
factor 0.1405) 46.64
TOTAL 378.59 Y
Add 15% CPOH on "Y" 56.79
TOTAL 435.38 Z
Add Cess @ 1% on "Z" 4.35
Cost of each 439.73
Say 439.75
SUB HEAD : 17- SANITARY INSTALLATIONS 1413
17.39.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7623 Hubless centrifugally cast (spun) iron
plain bend as per IS 15905-
100 mm dia each 1.00 230.00 230.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 258.66 W
Add 1 % Water charges on "W" 2.59
TOTAL 261.25 X
Add GST on "X" (multiplying
factor 0.1405) 36.71
TOTAL 297.95 Y
Add 15% CPOH on "Y" 44.69
TOTAL 342.65 Z
Add Cess @ 1% on "Z" 3.43
Cost of each 346.07
Say 346.05
17.39.2 75 mm dia
17.39.2.1 Sand cast iron S&S as per IS -1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1620 S.C.I. plain bend 75 mm dia each 1.00 210.00 210.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 232.87 W
Add 1 % Water charges on "W" 2.33
TOTAL 235.20 X
Add GST on "X" (multiplying
factor 0.1405) 33.05
TOTAL 268.25 Y
Add 15% CPOH on "Y" 40.24
TOTAL 308.49 Z
Add Cess @ 1% on "Z" 3.08
Cost of each 311.57
Say 311.55
17.39.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3629 S.C.I. S&S bend75mm dia each 1.00 200.00 200.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1414
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 222.87 W
Add 1 % Water charges on "W" 2.23
TOTAL 225.10 X
Add GST on "X" (multiplying
factor 0.1405) 31.63
TOTAL 256.73 Y
Add 15% CPOH on "Y" 38.51
TOTAL 295.24 Z
Add Cess @ 1% on "Z" 2.95
Cost of each 298.19
Say 298.20
17.39.2.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7624 Hubless centrifugally cast (spun) iron
plain bend as per IS 15905 -
75 mm dia each 1.00 160.00 160.00
9977 Carriage of materials and fixing
charges L.S. 10.79 2.12 22.87
TOTAL 182.87 W
Add 1 % Water charges on "W" 1.83
TOTAL 184.70 X
Add GST on "X" (multiplying
factor 0.1405) 25.95
TOTAL 210.65 Y
Add 15% CPOH on "Y" 31.60
TOTAL 242.25 Z
Add Cess @ 1% on "Z" 2.42
Cost of each 244.68
Say 244.70
17.40 Providing and fixing heel rest sanitary bend
17.40.1 100 mm dia
17.40.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1667 Sand cast iron heel rest bend
100mm dia each 1.00 355.00 355.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1415
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 383.66 W
Add 1 % Water charges on "W" 3.84
TOTAL 387.50 X
Add GST on "X" (multiplying
factor 0.1405) 54.44
TOTAL 441.94 Y
Add 15% CPOH on "Y" 66.29
TOTAL 508.23 Z
Add Cess @ 1% on "Z" 5.08
Cost of each 513.32
Say 513.30
17.40.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3634 S.C.I. S&S heel rest sanitary bend
100mm dia each 1.00 300.00 300.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 328.66 W
Add 1 % Water charges on "W" 3.29
TOTAL 331.95 X
Add GST on "X" (multiplying
factor 0.1405) 46.64
TOTAL 378.59 Y
Add 15% CPOH on "Y" 56.79
TOTAL 435.38 Z
Add Cess @ 1% on "Z" 4.35
Cost of each 439.73
Say 439.75
17.40.2 75 mm dia
17.40.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1666 Sand cast iron heel rest bend75mm dia each 1.00 300.00 300.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 322.87 W
Add 1 % Water charges on "W" 3.23
TOTAL 326.10 X
Add GST on "X" (multiplying
factor 0.1405) 45.82
TOTAL 371.92 Y
Add 15% CPOH on "Y" 55.79
TOTAL 427.71 Z
Add Cess @ 1% on "Z" 4.28
Cost of each 431.99
Say 432.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1416
17.40.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3635 S.C.I. S&S heel rest sanitary bend
75mm dia each 1.00 280.00 280.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 302.87 W
Add 1 % Water charges on "W" 3.03
TOTAL 305.90 X
Add GST on "X" (multiplying
factor 0.1405) 42.98
TOTAL 348.88 Y
Add 15% CPOH on "Y" 52.33
TOTAL 401.22 Z
Add Cess @ 1% on "Z" 4.01
Cost of each 405.23
Say 405.25
17.41 Providing and fixing double equal junction of required degree with access
door, insertion rubber washer 3 mm thick, bolts and nuts complete :
17.41.1 100x100x100x100 mm
17.41.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1637 S.C.I. double equal junctions
100x100x100x100 mm dia with
access door. each 1.00 730.00 730.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing
charges L.S. 13.39 2.12 28.39
TOTAL 776.39 W
Add 1 % Water charges on "W" 7.76
TOTAL 784.15 X
Add GST on "X" (multiplying
factor 0.1405) 110.17
TOTAL 894.32 Y
Add 15% CPOH on "Y" 134.15
TOTAL 1028.47 Z
Add Cess @ 1% on "Z" 10.28
Cost of each 1038.76
Say 1038.75
SUB HEAD : 17- SANITARY INSTALLATIONS 1417
17.41.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3654 S.C.I. S&S double equal junctions with
access door 100x100x100x100 mm. each 1.00 630.00 630.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.39 2.12 28.39
TOTAL 676.39 W
Add 1 % Water charges on "W" 6.76
TOTAL 683.15 X
Add GST on "X" (multiplying
factor 0.1405) 95.98
TOTAL 779.13 Y
Add 15% CPOH on "Y" 116.87
TOTAL 896.00 Z
Add Cess @ 1% on "Z" 8.96
Cost of each 904.96
Say 904.95
17.41.2 75x75x75x75 mm
17.41.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1636 S.C.I. double equal junctions
75x75x75x75 mm dia with access door. each 1.00 525.00 525.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 563.87 W
Add 1 % Water charges on "W" 5.64
TOTAL 569.51 X
Add GST on "X" (multiplying
factor 0.1405) 80.02
TOTAL 649.53 Y
Add 15% CPOH on "Y" 97.43
TOTAL 746.96 Z
Add Cess @ 1% on "Z" 7.47
Cost of each 754.43
Say 754.45
17.41.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3655 S.C.I. S&S double equal junctions
with access door 75x75x75x75 mm. each 1.00 500.00 500.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1418
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 538.87 W
Add 1 % Water charges on "W" 5.39
TOTAL 544.26 X
Add GST on "X" (multiplying
factor 0.1405) 76.47
TOTAL 620.73 Y
Add 15% CPOH on "Y" 93.11
TOTAL 713.84 Z
Add Cess @ 1% on "Z" 7.14
Cost of each 720.98
Say 721.00
17.42 Providing and fixing double equal plain junction of required degree.
17.42.1 100x100x100x100 mm
17.42.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1634 S.C.I. plain double equal junctions
100x100x100x100 mm dia each 1.00 615.00 615.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 643.66 W
Add 1 % Water charges on "W" 6.44
TOTAL 650.10 X
Add GST on "X" (multiplying
factor 0.1405) 91.34
TOTAL 741.44 Y
Add 15% CPOH on "Y" 111.22
TOTAL 852.65 Z
Add Cess @ 1% on "Z" 8.53
Cost of each 861.18
Say 861.20
17.42.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3650 S.C.I. S&S double equal junctions
100x100x100x100 mm each 1.00 630.00 630.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 658.66 W
Add 1 % Water charges on "W" 6.59
TOTAL 665.25 X
Add GST on "X" (multiplying
factor 0.1405) 93.47
TOTAL 758.72 Y
Add 15% CPOH on "Y" 113.81
TOTAL 872.52 Z
Add Cess @ 1% on "Z" 8.73
Cost of each 881.25
Say 881.25
SUB HEAD : 17- SANITARY INSTALLATIONS 1419
17.42.1.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7625 Hubless centrifugally cast (spun) iron
double equal plain junction as per IS
15905 - 100x100x100x100 mm dia each 1.00 510.00 510.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 538.66 W
Add 1 % Water charges on "W" 5.39
TOTAL 544.05 X
Add GST on "X" (multiplying
factor 0.1405) 76.44
TOTAL 620.49 Y
Add 15% CPOH on "Y" 93.07
TOTAL 713.56 Z
Add Cess @ 1% on "Z" 7.14
Cost of each 720.70
Say 720.70
17.42.2 75x75x75x75 mm
17.42.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1633 S.C.I. plain double equal junctions
75x75x75x75 mm dia each 1.00 410.00 410.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 432.87 W
Add 1 % Water charges on "W" 4.33
TOTAL 437.20 X
Add GST on "X" (multiplying
factor 0.1405) 61.43
TOTAL 498.63 Y
Add 15% CPOH on "Y" 74.79
TOTAL 573.43 Z
Add Cess @ 1% on "Z" 5.73
Cost of each 579.16
Say 579.15
17.42.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3651 S.C.I. S&S double equal junctions
75x75x75x75 mm each 1.00 470.00 470.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1420
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 492.87 W
Add 1 % Water charges on "W" 4.93
TOTAL 497.80 X
Add GST on "X" (multiplying
factor 0.1405) 69.94
TOTAL 567.74 Y
Add 15% CPOH on "Y" 85.16
TOTAL 652.91 Z
Add Cess @ 1% on "Z" 6.53
Cost of each 659.44
Say 659.45
17.42.2.3 Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7626 Hubless centrifugally cast (spun) iron
double equal plain junction as per IS
15905 - 75x75x75x75 mm dia each 1.00 275.00 275.00
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 297.87 W
Add 1 % Water charges on "W" 2.98
TOTAL 300.85 X
Add GST on "X" (multiplying
factor 0.1405) 42.27
TOTAL 343.12 Y
Add 15% CPOH on "Y" 51.47
TOTAL 394.59 Z
Add Cess @ 1% on "Z" 3.95
Cost of each 398.54
Say 398.55
17.43 Providing and fixing single equal plain junction of required degree with access
door, insertion rubber washer 3 mm thick, bolts and nuts complete.
17.43.1 100x100x100 mm
17.43.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1631 S.C.I. single equal junctions 100x
100x100 mm dia with access door. each 1.00 455.00 455.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1421
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 501.66 W
Add 1 % Water charges on "W" 5.02
TOTAL 506.68 X
Add GST on "X" (multiplying
factor 0.1405) 71.19
TOTAL 577.87 Y
Add 15% CPOH on "Y" 86.68
TOTAL 664.55 Z
Add Cess @ 1% on "Z" 6.65
Cost of each 671.19
Say 671.20
17.43.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3644 S.C.I. S&S single equal junctions
with access door 100x100x100 mm each 1.00 500.00 500.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 546.66 W
Add 1 % Water charges on "W" 5.47
TOTAL 552.13 X
Add GST on "X" (multiplying
factor 0.1405) 77.57
TOTAL 629.70 Y
Add 15% CPOH on "Y" 94.46
TOTAL 724.16 Z
Add Cess @ 1% on "Z" 7.24
Cost of each 731.40
Say 731.40
17.43.2 75x75x75 mm
17.43.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1630 S.C.I. single equal junctions75x75x
75 mm dia with access door. each 1.00 390.00 390.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1422
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 428.87 W
Add 1 % Water charges on "W" 4.29
TOTAL 433.16 X
Add GST on "X" (multiplying
factor 0.1405) 60.86
TOTAL 494.02 Y
Add 15% CPOH on "Y" 74.10
TOTAL 568.13 Z
Add Cess @ 1% on "Z" 5.68
Cost of each 573.81
Say 573.80
17.43.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3645 S.C.I. S&S single equal junctions with
access door 75x75x75 mm each 1.00 390.00 390.00
1373 Rubber insertions for 80 mm dia pipe
joints each 1.00 16.00 16.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 428.87 W
Add 1 % Water charges on "W" 4.29
TOTAL 433.16 X
Add GST on "X" (multiplying
factor 0.1405) 60.86
TOTAL 494.02 Y
Add 15% CPOH on "Y" 74.10
TOTAL 568.13 Z
Add Cess @ 1% on "Z" 5.68
Cost of each 573.81
Say 573.80
17.44 Providing and fixing single equal plain junction of required degree :
17.44.1 100x100x100 mm
17.44.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1628 S.C.I. plain single equal junctions
100x100x100 mm dia each 1.00 405.00 405.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1423
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing
charges L.S. 13.52 2.12 28.66
TOTAL 433.66 W
Add 1 % Water charges on "W" 4.34
TOTAL 438.00 X
Add GST on "X" (multiplying
factor 0.1405) 61.54
TOTAL 499.54 Y
Add 15% CPOH on "Y" 74.93
TOTAL 574.47 Z
Add Cess @ 1% on "Z" 5.74
Cost of each 580.21
Say 580.20
17.44.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3640 S.C.I. S&S single equal junctions
100x100x100 mm each 1.00 500.00 500.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 528.66 W
Add 1 % Water charges on "W" 5.29
TOTAL 533.95 X
Add GST on "X" (multiplying
factor 0.1405) 75.02
TOTAL 608.97 Y
Add 15% CPOH on "Y" 91.35
TOTAL 700.31 Z
Add Cess @ 1% on "Z" 7.00
Cost of each 707.32
Say 707.30
17.44.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as
per IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7627 Hubless centrifugally cast (spun) iron
single equal plain junction as per IS
15905 - 100x100x100 mm dia each 1.00 400.00 400.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 428.66 W
Add 1 % Water charges on "W" 4.29
TOTAL 432.95 X
Add GST on "X" (multiplying
factor 0.1405) 60.83
TOTAL 493.78 Y
Add 15% CPOH on "Y" 74.07
TOTAL 567.85 Z
Add Cess @ 1% on "Z" 5.68
Cost of each 573.52
Say 573.50
SUB HEAD : 17- SANITARY INSTALLATIONS 1424
17.44.2 75x75x75 mm
17.44.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1627 S.C.I. plain single equal junctions
75x75x75 mm dia each 1.00 315.00 315.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 337.87 W
Add 1 % Water charges on "W" 3.38
TOTAL 341.25 X
Add GST on "X" (multiplying
factor 0.1405) 47.95
TOTAL 389.20 Y
Add 15% CPOH on "Y" 58.38
TOTAL 447.58 Z
Add Cess @ 1% on "Z" 4.48
Cost of each 452.06
Say 452.05
17.44.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3641 S.C.I. S&S single equal junctions
75x75x75 mm each 1.00 350.00 350.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 372.87 W
Add 1 % Water charges on "W" 3.73
TOTAL 376.60 X
Add GST on "X" (multiplying
factor 0.1405) 52.91
TOTAL 429.52 Y
Add 15% CPOH on "Y" 64.43
TOTAL 493.94 Z
Add Cess @ 1% on "Z" 4.94
Cost of each 498.88
Say 498.90
17.44.2.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7628 Hubless centrifugally cast (spun) iron
single equal plain junction as per IS
15905 - 75x75x75 mm dia each 1.00 215.00 215.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1425
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 237.87 W
Add 1 % Water charges on "W" 2.38
TOTAL 240.25 X
Add GST on "X" (multiplying
factor 0.1405) 33.76
TOTAL 274.01 Y
Add 15% CPOH on "Y" 41.10
TOTAL 315.11 Z
Add Cess @ 1% on "Z" 3.15
Cost of each 318.26
Say 318.25
17.45 Providing and fixing double unequal junction of required degree with access
door, insertion rubber washer 3 mm thick, bolts and nuts complete:
17.45.1 100x100x75x75 mm
17.45.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1662 Sand cast iron S&S double unequal
junctions: 100x100x75x75 mm dia with
access door. each 1.00 725.00 725.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 771.66 W
Add 1 % Water charges on "W" 7.72
TOTAL 779.38 X
Add GST on "X" (multiplying
factor 0.1405) 109.50
TOTAL 888.88 Y
Add 15% CPOH on "Y" 133.33
TOTAL 1022.21 Z
Add Cess @ 1% on "Z" 10.22
Cost of each 1032.44
Say 1032.45
17.45.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3674 S.C.I. S&S double unequal junctions
with access door 100x100x75x75 mm each 1.00 900.00 900.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1426
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 946.66 W
Add 1 % Water charges on "W" 9.47
TOTAL 956.13 X
Add GST on "X" (multiplying
factor 0.1405) 134.34
TOTAL 1090.47 Y
Add 15% CPOH on "Y" 163.57
TOTAL 1254.03 Z
Add Cess @ 1% on "Z" 12.54
Cost of each 1266.58
Say 1266.60
17.46 Providing and fixing double unequal plain junction of required degree :
17.46.1 100x100x75x75 mm
17.46.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1659 Sand cast iron S&S plain double
unequal junctions : 100x100x75x
75 mm dia each 1.00 625.00 625.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 653.66 W
Add 1 % Water charges on "W" 6.54
TOTAL 660.20 X
Add GST on "X" (multiplying
factor 0.1405) 92.76
TOTAL 752.96 Y
Add 15% CPOH on "Y" 112.94
TOTAL 865.90 Z
Add Cess @ 1% on "Z" 8.66
Cost of each 874.56
Say 874.55
17.46.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3670 S.C.I. S&S double unequal junctions
100x100x75x75 mm each 1.00 800.00 800.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 828.66 W
Add 1 % Water charges on "W" 8.29
TOTAL 836.95 X
Add GST on "X" (multiplying
factor 0.1405) 117.59
TOTAL 954.54 Y
Add 15% CPOH on "Y" 143.18
TOTAL 1097.72 Z
Add Cess @ 1% on "Z" 10.98
Cost of each 1108.70
Say 1108.70
SUB HEAD : 17- SANITARY INSTALLATIONS 1427
17.46.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7629 Hubless centrifugally cast (spun) iron
double unequal plain junction as per IS
15905 - 100x100x75x75 mm dia each 1.00 400.00 400.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 428.66 W
Add 1 % Water charges on "W" 4.29
TOTAL 432.95 X
Add GST on "X" (multiplying
factor 0.1405) 60.83
TOTAL 493.78 Y
Add 15% CPOH on "Y" 74.07
TOTAL 567.85 Z
Add Cess @ 1% on "Z" 5.68
Cost of each 573.52
Say 573.50
17.47 Providing and fixing single unequal junction of required degree with access
door, insertion rubber washer 3 mm thick, bolts and nuts complete :
17.47.1 100x100x75 mm
17.47.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1656 Sand cast iron S&S single unequal
junctions: 100x100x75 mm dia with
access door. each 1.00 575.00 575.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing
charges L.S. 13.52 2.12 28.66
TOTAL 621.66 W
Add 1 % Water charges on "W" 6.22
TOTAL 627.88 X
Add GST on "X" (multiplying
factor 0.1405) 88.22
TOTAL 716.10 Y
Add 15% CPOH on "Y" 107.41
TOTAL 823.51 Z
Add Cess @ 1% on "Z" 8.24
Cost of each 831.75
Say 831.75
SUB HEAD : 17- SANITARY INSTALLATIONS 1428
17.47.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3664 S.C.I. S&S single unequal junctions
with access door 100x100x75 mm each 1.00 650.00 650.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 696.66 W
Add 1 % Water charges on "W" 6.97
TOTAL 703.63 X
Add GST on "X" (multiplying
factor 0.1405) 98.86
TOTAL 802.49 Y
Add 15% CPOH on "Y" 120.37
TOTAL 922.86 Z
Add Cess @ 1% on "Z" 9.23
Cost of each 932.09
Say 932.10
17.48 Providing and fixing single unequal plain junction of required degree :
17.48.1 100x100x75 mm
17.48.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1653 Sand cast iron S&S plain single
unequal junctions : 100x100x75 mm dia each 1.00 525.00 525.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 553.66 W
Add 1 % Water charges on "W" 5.54
TOTAL 559.20 X
Add GST on "X" (multiplying
factor 0.1405) 78.57
TOTAL 637.77 Y
Add 15% CPOH on "Y" 95.66
TOTAL 733.43 Z
Add Cess @ 1% on "Z" 7.33
Cost of each 740.77
Say 740.75
17.48.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3660 S.C.I. S&S single unequal junctions
100x100x75 mm each 1.00 600.00 600.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1429
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 628.66 W
Add 1 % Water charges on "W" 6.29
TOTAL 634.95 X
Add GST on "X" (multiplying
factor 0.1405) 89.21
TOTAL 724.16 Y
Add 15% CPOH on "Y" 108.62
TOTAL 832.78 Z
Add Cess @ 1% on "Z" 8.33
Cost of each 841.11
Say 841.10
17.48.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7630 Hubless centrifugally cast (spun) iron
single unequal plain junction as per IS
15905 - 100x100x75 mm dia each 1.00 375.00 375.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 403.66 W
Add 1 % Water charges on "W" 4.04
TOTAL 407.70 X
Add GST on "X" (multiplying
factor 0.1405) 57.28
TOTAL 464.98 Y
Add 15% CPOH on "Y" 69.75
TOTAL 534.73 Z
Add Cess @ 1% on "Z" 5.35
Cost of each 540.08
Say 540.10
17.49 Providing and fixing double equal plain invert branch of required degree:
17.49.1 100x100x100x100 mm
17.49.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1673 S.C.I. double equal invert branch of
required degree 100x100x100x
100 mm dia each 1.00 550.00 550.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1430
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 578.66 W
Add 1 % Water charges on "W" 5.79
TOTAL 584.45 X
Add GST on "X" (multiplying
factor 0.1405) 82.12
TOTAL 666.56 Y
Add 15% CPOH on "Y" 99.98
TOTAL 766.55 Z
Add Cess @ 1% on "Z" 7.67
Cost of each 774.21
Say 774.20
17.49.1.2 Sand cast iron S&S as per IS 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3685 S.C.I. S&S double equal invert branch
of required degree100x100x100x
100 mm dia each 1.00 540.00 540.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 568.66 W
Add 1 % Water charges on "W" 5.69
TOTAL 574.35 X
Add GST on "X" (multiplying
factor 0.1405) 80.70
TOTAL 655.05 Y
Add 15% CPOH on "Y" 98.26
TOTAL 753.30 Z
Add Cess @ 1% on "Z" 7.53
Cost of each 760.83
Say 760.85
17.49.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7631 Hubless centrifugally cast (spun) iron
double equal plain invert branch as per
IS 15905 - 100x100x100x100 mm dia each 1.00 625.00 625.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 653.66 W
Add 1 % Water charges on "W" 6.54
TOTAL 660.20 X
Add GST on "X" (multiplying
factor 0.1405) 92.76
TOTAL 752.96 Y
Add 15% CPOH on "Y" 112.94
TOTAL 865.90 Z
Add Cess @ 1% on "Z" 8.66
Cost of each 874.56
Say 874.55
SUB HEAD : 17- SANITARY INSTALLATIONS 1431
17.49.2 75x75x75x75 mm
17.49.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1672 S.C.I. double equal invert branch of
required degree 75x75x75x75 mm dia each 1.00 425.00 425.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 447.87 W
Add 1 % Water charges on "W" 4.48
TOTAL 452.35 X
Add GST on "X" (multiplying
factor 0.1405) 63.56
TOTAL 515.91 Y
Add 15% CPOH on "Y" 77.39
TOTAL 593.30 Z
Add Cess @ 1% on "Z" 5.93
Cost of each 599.23
Say 599.25
17.49.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3686 S.C.I. S&S double equal invert branch
of required degree 75x75x75x
75 mm dia each 1.00 450.00 450.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 472.87 W
Add 1 % Water charges on "W" 4.73
TOTAL 477.60 X
Add GST on "X" (multiplying
factor 0.1405) 67.10
TOTAL 544.71 Y
Add 15% CPOH on "Y" 81.71
TOTAL 626.41 Z
Add Cess @ 1% on "Z" 6.26
Cost of each 632.68
Say 632.70
17.50 Providing and fixing single equal plain invert branch of required degree :
17.50.1 100x100x100 mm
17.50.1.1 Sand cast iron S&S as per iron 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1670 S.C.I. single equal invert branch of
required degree 100x100x100 mm dia each 1.00 435.00 435.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1432
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 463.66 W
Add 1 % Water charges on "W" 4.64
TOTAL 468.30 X
Add GST on "X" (multiplying
factor 0.1405) 65.80
TOTAL 534.10 Y
Add 15% CPOH on "Y" 80.11
TOTAL 614.21 Z
Add Cess @ 1% on "Z" 6.14
Cost of each 620.35
Say 620.35
17.50.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3681 S.C.I. S&S single equal invert branch
of required degree 100x100x
100 mm dia each 1.00 430.00 430.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 458.66 W
Add 1 % Water charges on "W" 4.59
TOTAL 463.25 X
Add GST on "X" (multiplying
factor 0.1405) 65.09
TOTAL 528.34 Y
Add 15% CPOH on "Y" 79.25
TOTAL 607.59 Z
Add Cess @ 1% on "Z" 6.08
Cost of each 613.66
Say 613.65
17.50.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7632 Hubless centrifugally cast (spun) iron
single equal plain invert branch as per
IS 15905 - 100x100x100 mm dia each 1.00 390.00 390.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1433
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 418.66 W
Add 1 % Water charges on "W" 4.19
TOTAL 422.85 X
Add GST on "X" (multiplying
factor 0.1405) 59.41
TOTAL 482.26 Y
Add 15% CPOH on "Y" 72.34
TOTAL 554.60 Z
Add Cess @ 1% on "Z" 5.55
Cost of each 560.14
Say 560.15
17.50.2 75x75x75 mm
17.50.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1669 S.C.I. single equal invert branch of
required degree75x75x75 mm dia each 1.00 350.00 350.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 372.87 W
Add 1 % Water charges on "W" 3.73
TOTAL 376.60 X
Add GST on "X" (multiplying
factor 0.1405) 52.91
TOTAL 429.52 Y
Add 15% CPOH on "Y" 64.43
TOTAL 493.94 Z
Add Cess @ 1% on "Z" 4.94
Cost of each 498.88
Say 498.90
17.50.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3682 S.C.I. S&S single equal invert branch
of required degree 75x75x75 mm dia each 1.00 330.00 330.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 352.87 W
Add 1 % Water charges on "W" 3.53
TOTAL 356.40 X
Add GST on "X" (multiplying
factor 0.1405) 50.07
TOTAL 406.48 Y
Add 15% CPOH on "Y" 60.97
TOTAL 467.45 Z
Add Cess @ 1% on "Z" 4.67
Cost of each 472.12
Say 472.10
SUB HEAD : 17- SANITARY INSTALLATIONS 1434
17.50.2.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7633 Hubless centrifugally cast (spun) iron
single equal plain invert branch as per
IS 15905 - 75x75x75 mm dia each 1.00 260.00 260.00
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 282.87 W
Add 1 % Water charges on "W" 2.83
TOTAL 285.70 X
Add GST on "X" (multiplying
factor 0.1405) 40.14
TOTAL 325.84 Y
Add 15% CPOH on "Y" 48.88
TOTAL 374.72 Z
Add Cess @ 1% on "Z" 3.75
Cost of each 378.47
Say 378.45
17.51 Providing and fixing double unequal invert branch of required degree :
17.51.1 100x100x75x75 mm
17.51.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1677 S.C.I. double unequal invert branch of
required degree 100x100x75x75 mm dia each 1.00 600.00 600.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 628.66 W
Add 1 % Water charges on "W" 6.29
TOTAL 634.95 X
Add GST on "X" (multiplying
factor 0.1405) 89.21
TOTAL 724.16 Y
Add 15% CPOH on "Y" 108.62
TOTAL 832.78 Z
Add Cess @ 1% on "Z" 8.33
Cost of each 841.11
Say 841.10
17.51.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3695 S.C.I. S&S double unequal invert
branch of required
degree100x100x75x75 mm dia each 1.00 730.00 730.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1435
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 758.66 W
Add 1 % Water charges on "W" 7.59
TOTAL 766.25 X
Add GST on "X" (multiplying
factor 0.1405) 107.66
TOTAL 873.91 Y
Add 15% CPOH on "Y" 131.09
TOTAL 1004.99 Z
Add Cess @ 1% on "Z" 10.05
Cost of each 1015.04
Say 1015.05
17.52 Providing and fixing single unequal plain invert branch of required degree :
17.52.1 100x100x75 mm
17.52.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1674 S.C.I. single unequal invert branch of
required degree100x100x75 mm dia each 1.00 500.00 500.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 528.66 W
Add 1 % Water charges on "W" 5.29
TOTAL 533.95 X
Add GST on "X" (multiplying
factor 0.1405) 75.02
TOTAL 608.97 Y
Add 15% CPOH on "Y" 91.35
TOTAL 700.31 Z
Add Cess @ 1% on "Z" 7.00
Cost of each 707.32
Say 707.30
17.52.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3690 S.C.I. S&S single unequal invert
branch of required degree100x100x
75 mm dia each 1.00 550.00 550.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1436
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 578.66 W
Add 1 % Water charges on "W" 5.79
TOTAL 584.45 X
Add GST on "X" (multiplying
factor 0.1405) 82.12
TOTAL 666.56 Y
Add 15% CPOH on "Y" 99.98
TOTAL 766.55 Z
Add Cess @ 1% on "Z" 7.67
Cost of each 774.21
Say 774.20
17.52.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7634 Hubless centrifugally cast (spun) iron
single unequal plain invert branch 45
degree as per IS 15905 - 100x100x
75 mm dia each 1.00 430.00 430.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 458.66 W
Add 1 % Water charges on "W" 4.59
TOTAL 463.25 X
Add GST on "X" (multiplying
factor 0.1405) 65.09
TOTAL 528.34 Y
Add 15% CPOH on "Y" 79.25
TOTAL 607.59 Z
Add Cess @ 1% on "Z" 6.08
Cost of each 613.66
Say 613.65
17.53 Providing and fixing sand cast iron S&S off sets as per IS: 1729
17.53.1 76 mm off sets
17.53.1.1 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3746 S.C.I. S&S, 75 mm offset for
75 mm dia pipe each 1.00 220.00 220.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1437
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 242.87 W
Add 1 % Water charges on "W" 2.43
TOTAL 245.30 X
Add GST on "X" (multiplying
factor 0.1405) 34.47
TOTAL 279.77 Y
Add 15% CPOH on "Y" 41.97
TOTAL 321.73 Z
Add Cess @ 1% on "Z" 3.22
Cost of each 324.95
Say 324.95
17.53.1.2 With 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3747 S.C.I. S&S, 75 mm offset for
100 mm dia pipe each 1.00 360.00 360.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 382.87 W
Add 1 % Water charges on "W" 3.83
TOTAL 386.70 X
Add GST on "X" (multiplying
factor 0.1405) 54.33
TOTAL 441.04 Y
Add 15% CPOH on "Y" 66.16
TOTAL 507.19 Z
Add Cess @ 1% on "Z" 5.07
Cost of each 512.26
Say 512.25
17.53.2 114 mm off sets
17.53.2.1 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3712 S.C.I. S&S, 114 mm offset for
75 mm dia pipe each 1.00 310.00 310.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 338.66 W
Add 1 % Water charges on "W" 3.39
TOTAL 342.05 X
Add GST on "X" (multiplying
factor 0.1405) 48.06
TOTAL 390.11 Y
Add 15% CPOH on "Y" 58.52
TOTAL 448.62 Z
Add Cess @ 1% on "Z" 4.49
Cost of each 453.11
Say 453.10
SUB HEAD : 17- SANITARY INSTALLATIONS 1438
17.53.2.2 With 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3713 S.C.I. S&S, 114 mm offset for
100 mm dia pipe each 1.00 390.00 390.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 418.66 W
Add 1 % Water charges on "W" 4.19
TOTAL 422.85 X
Add GST on "X" (multiplying
factor 0.1405) 59.41
TOTAL 482.26 Y
Add 15% CPOH on "Y" 72.34
TOTAL 554.60 Z
Add Cess @ 1% on "Z" 5.55
Cost of each 560.14
Say 560.15
17.53.3 152 mm off sets
17.53.3.1 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3716 S.C.I. S&S, 152 mm offset for
75 mm dia pipe each 1.00 360.00 360.00
9988 Carriage of materials and fixing charges L.S. 17.94 2.12 38.03
TOTAL 398.03 W
Add 1 % Water charges on "W" 3.98
TOTAL 402.01 X
Add GST on "X" (multiplying
factor 0.1405) 56.48
TOTAL 458.50 Y
Add 15% CPOH on "Y" 68.77
TOTAL 527.27 Z
Add Cess @ 1% on "Z" 5.27
Cost of each 532.54
Say 532.55
17.53.3.2 With 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3717 S.C.I. S&S, 152 mm offset for
100 mm dia pipe each 1.00 460.00 460.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1439
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 17.94 2.12 38.03
TOTAL 498.03 W
Add 1 % Water charges on "W" 4.98
TOTAL 503.01 X
Add GST on "X" (multiplying
factor 0.1405) 70.67
TOTAL 573.69 Y
Add 15% CPOH on "Y" 86.05
TOTAL 659.74 Z
Add Cess @ 1% on "Z" 6.60
Cost of each 666.34
Say 666.35
17.53A Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside
& outside as per IS:15905
17.53A.1 65 mm offsets
17.53A.1.1 With 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7635 Hubless centrifugally cast (spun) iron
65 mm offset with 100 mm dia pipe as
per IS 15905 each 1.00 360.00 360.00
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 382.87 W
Add 1 % Water charges on "W" 3.83
TOTAL 386.70 X
Add GST on "X" (multiplying
factor 0.1405) 54.33
TOTAL 441.04 Y
Add 15% CPOH on "Y" 66.16
TOTAL 507.19 Z
Add Cess @ 1% on "Z" 5.07
Cost of each 512.26
Say 512.25
17.53A.1.2 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7636 Hubless centrifugally cast (spun) iron
65 mm offset with 75 mm dia pipe as
per IS 15905 each 1.00 295.00 295.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1440
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 317.87 W
Add 1 % Water charges on "W" 3.18
TOTAL 321.05 X
Add GST on "X" (multiplying
factor 0.1405) 45.11
TOTAL 366.16 Y
Add 15% CPOH on "Y" 54.92
TOTAL 421.09 Z
Add Cess @ 1% on "Z" 4.21
Cost of each 425.30
Say 425.30
17.54 Providing and fixing sand cast iron S&S off sets as per IS: 3989 :
17.54.1 75 mm off sets
17.54.1.1 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3699 S.C.I. S&S, 75 mm offset for
75 mm dia pipe each 1.00 230.00 230.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 252.87 W
Add 1 % Water charges on "W" 2.53
TOTAL 255.40 X
Add GST on "X" (multiplying
factor 0.1405) 35.88
TOTAL 291.29 Y
Add 15% CPOH on "Y" 43.69
TOTAL 334.98 Z
Add Cess @ 1% on "Z" 3.35
Cost of each 338.33
Say 338.35
17.54.2 150 mm off sets
17.54.2.1 With 75 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3707 S.C.I. S&S, 150 mm offset for
75 mm dia pipe each 1.00 300.00 300.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1441
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 16.12 2.12 34.17
TOTAL 334.17 W
Add 1 % Water charges on "W" 3.34
TOTAL 337.52 X
Add GST on "X" (multiplying
factor 0.1405) 47.42
TOTAL 384.94 Y
Add 15% CPOH on "Y" 57.74
TOTAL 442.68 Z
Add Cess @ 1% on "Z" 4.43
Cost of each 447.10
Say 447.10
17.54.2.2 With 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3708 S.C.I. S&S, 150 mm offset for
100 mm dia pipe each 1.00 400.00 400.00
9988 Carriage of materials and fixing charges L.S. 16.12 2.12 34.17
TOTAL 434.17 W
Add 1 % Water charges on "W" 4.34
TOTAL 438.52 X
Add GST on "X" (multiplying
factor 0.1405) 61.61
TOTAL 500.13 Y
Add 15% CPOH on "Y" 75.02
TOTAL 575.15 Z
Add Cess @ 1% on "Z" 5.75
Cost of each 580.90
Say 580.90
17.54A Providing and fixing Hubless centrifugally cast iron offsets epoxy coated inside
& outside as per IS:15905
17.54A.1 130 mm offsets
17.54A.1.1 With 100 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7637 Hubless centrifugally cast (spun) iron
130 mm offset with 100 mm dia pipe
as per IS 15905 each 1.00 440.00 440.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1442
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 468.66 W
Add 1 % Water charges on "W" 4.69
TOTAL 473.35 X
Add GST on "X" (multiplying
factor 0.1405) 66.51
TOTAL 539.85 Y
Add 15% CPOH on "Y" 80.98
TOTAL 620.83 Z
Add Cess @ 1% on "Z" 6.21
Cost of each 627.04
Say 627.05
17.54A.1.2 With 75 mm dia
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7638 Hubless centrifugally cast (spun) iron
130 mm offset with 75 mm dia pipe as
per IS 15905 each 1.00 310.00 310.00
9999 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 332.87 W
Add 1 % Water charges on "W" 3.33
TOTAL 336.20 X
Add GST on "X" (multiplying
factor 0.1405) 47.24
TOTAL 383.44 Y
Add 15% CPOH on "Y" 57.52
TOTAL 440.96 Z
Add Cess @ 1% on "Z" 4.41
Cost of each 445.37
Say 445.35
17.55 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts &
nuts complete :
17.55.1 100 mm
17.55.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1683 S.C.I. door pieces 100 mm dia each 1.00 485.00 485.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1443
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 531.66 W
Add 1 % Water charges on "W" 5.32
TOTAL 536.98 X
Add GST on "X" (multiplying
factor 0.1405) 75.45
TOTAL 612.42 Y
Add 15% CPOH on "Y" 91.86
TOTAL 704.29 Z
Add Cess @ 1% on "Z" 7.04
Cost of each 711.33
Say 711.35
17.55.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3728 S.C.I. S&S door pieces 100 mm dia each 1.00 410.00 410.00
1374 Rubber insertions for 100 mm dia
pipe joints each 1.00 18.00 18.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 456.66 W
Add 1 % Water charges on "W" 4.57
TOTAL 461.23 X
Add GST on "X" (multiplying
factor 0.1405) 64.80
TOTAL 526.03 Y
Add 15% CPOH on "Y" 78.90
TOTAL 604.94 Z
Add Cess @ 1% on "Z" 6.05
Cost of each 610.99
Say 611.00
17.55.2 75 mm
17.55.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1682 S.C.I. door pieces 75 mm dia each 1.00 285.00 285.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 323.87 W
Add 1 % Water charges on "W" 3.24
TOTAL 327.11 X
Add GST on "X" (multiplying
factor 0.1405) 45.96
TOTAL 373.07 Y
Add 15% CPOH on "Y" 55.96
TOTAL 429.03 Z
Add Cess @ 1% on "Z" 4.29
Cost of each 433.32
Say 433.30
SUB HEAD : 17- SANITARY INSTALLATIONS 1444
17.55.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3729 S.C.I. S&S door pieces 75 mm dia each 1.00 300.00 300.00
1373 Rubber insertions for 80 mm dia
pipe joints each 1.00 16.00 16.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 338.87 W
Add 1 % Water charges on "W" 3.39
TOTAL 342.26 X
Add GST on "X" (multiplying
factor 0.1405) 48.09
TOTAL 390.35 Y
Add 15% CPOH on "Y" 58.55
TOTAL 448.90 Z
Add Cess @ 1% on "Z" 4.49
Cost of each 453.39
Say 453.40
17.56 Providing and fixing terminal guard :
17.56.1 100 mm
17.56.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1640 Slotted cowl (terminal guard )
100 mm dia each 1.00 265.00 265.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 293.66 W
Add 1 % Water charges on "W" 2.94
TOTAL 296.60 X
Add GST on "X" (multiplying
factor 0.1405) 41.67
TOTAL 338.27 Y
Add 15% CPOH on "Y" 50.74
TOTAL 389.01 Z
Add Cess @ 1% on "Z" 3.89
Cost of each 392.90
Say 392.90
17.56.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3733 S.C.I. S&S, Slotted Cowl
(Terminal Guard) 100 mm each 1.00 300.00 300.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1445
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 328.66 W
Add 1 % Water charges on "W" 3.29
TOTAL 331.95 X
Add GST on "X" (multiplying
factor 0.1405) 46.64
TOTAL 378.59 Y
Add 15% CPOH on "Y" 56.79
TOTAL 435.38 Z
Add Cess @ 1% on "Z" 4.35
Cost of each 439.73
Say 439.75
17.56.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7641 Hubless centrifugally cast (spun) iron
terminal guard (slotted cowl) -
100 mm dia as per IS 15905 each 1.00 270.00 270.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 298.66 W
Add 1 % Water charges on "W" 2.99
TOTAL 301.65 X
Add GST on "X" (multiplying
factor 0.1405) 42.38
TOTAL 344.03 Y
Add 15% CPOH on "Y" 51.60
TOTAL 395.64 Z
Add Cess @ 1% on "Z" 3.96
Cost of each 399.59
Say 399.60
17.56.2 75 mm
17.56.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1639 Slotted cowl (terminal guard )75 mm dia each 1.00 215.00 215.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 237.87 W
Add 1 % Water charges on "W" 2.38
TOTAL 240.25 X
Add GST on "X" (multiplying
factor 0.1405) 33.76
TOTAL 274.01 Y
Add 15% CPOH on "Y" 41.10
TOTAL 315.11 Z
Add Cess @ 1% on "Z" 3.15
Cost of each 318.26
Say 318.25
SUB HEAD : 17- SANITARY INSTALLATIONS 1446
17.56.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3734 S.C.I. S&S, Slotted Cowl (Terminal
Guard) 75 mm each 1.00 210.00 210.00
9988 Carriage of materials and fixing
charges L.S. 10.79 2.12 22.87
TOTAL 232.87 W
Add 1 % Water charges on "W" 2.33
TOTAL 235.20 X
Add GST on "X" (multiplying
factor 0.1405) 33.05
TOTAL 268.25 Y
Add 15% CPOH on "Y" 40.24
TOTAL 308.49 Z
Add Cess @ 1% on "Z" 3.08
Cost of each 311.57
Say 311.55
17.57 Providing and fixing collar :
17.57.1 100 mm
17.57.1.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1686 S.C.I. collar 100 mm dia each 1.00 270.00 270.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 298.66 W
Add 1 % Water charges on "W" 2.99
TOTAL 301.65 X
Add GST on "X" (multiplying
factor 0.1405) 42.38
TOTAL 344.03 Y
Add 15% CPOH on "Y" 51.60
TOTAL 395.64 Z
Add Cess @ 1% on "Z" 3.96
Cost of each 399.59
Say 399.60
17.57.1.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3738 S.C.I. S&S, collars 100 mm each 1.00 300.00 300.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1447
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 328.66 W
Add 1 % Water charges on "W" 3.29
TOTAL 331.95 X
Add GST on "X" (multiplying
factor 0.1405) 46.64
TOTAL 378.59 Y
Add 15% CPOH on "Y" 56.79
TOTAL 435.38 Z
Add Cess @ 1% on "Z" 4.35
Cost of each 439.73
Say 439.75
17.57.2 75 mm
17.57.2.1 Sand cast iron S&S as per IS - 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1685 S.C.I. collar 75 mm dia each 1.00 180.00 180.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 202.87 W
Add 1 % Water charges on "W" 2.03
TOTAL 204.90 X
Add GST on "X" (multiplying
factor 0.1405) 28.79
TOTAL 233.69 Y
Add 15% CPOH on "Y" 35.05
TOTAL 268.75 Z
Add Cess @ 1% on "Z" 2.69
Cost of each 271.43
Say 271.45
17.57.2.2 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3739 S.C.I. S&S, collars 75 mm each 1.00 180.00 180.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 202.87 W
Add 1 % Water charges on "W" 2.03
TOTAL 204.90 X
Add GST on "X" (multiplying
factor 0.1405) 28.79
TOTAL 233.69 Y
Add 15% CPOH on "Y" 35.05
TOTAL 268.75 Z
Add Cess @ 1% on "Z" 2.69
Cost of each 271.43
Say 271.45
SUB HEAD : 17- SANITARY INSTALLATIONS 1448
17.57A Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe
17.57A.1 100 mm dia
17.57A.1.1 SS 304 grade coupling with EPDM rubber gasket
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7644 SS 304 grade shielded coupling with
EPDM rubber gasket for 100 mm dia
Hubless centrifugally cast (spun) iron each 1.00 275.00 275.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 303.66 W
Add 1 % Water charges on "W" 3.04
TOTAL 306.70 X
Add GST on "X" (multiplying
factor 0.1405) 43.09
TOTAL 349.79 Y
Add 15% CPOH on "Y" 52.47
TOTAL 402.26 Z
Add Cess @ 1% on "Z" 4.02
Cost of each 406.28
Say 406.30
17.57A.2 75 mm dia
17.57A.2.1 SS 304 grade coupling with EPDM rubber gasket
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7645 SS 304 grade shielded coupling with
EPDM rubber gasket for 75 mm dia
Hubless centrifugally cast (spun) iron each 1.00 250.00 250.00
9977 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 272.87 W
Add 1 % Water charges on "W" 2.73
TOTAL 275.60 X
Add GST on "X" (multiplying
factor 0.1405) 38.72
TOTAL 314.33 Y
Add 15% CPOH on "Y" 47.15
TOTAL 361.47 Z
Add Cess @ 1% on "Z" 3.61
Cost of each 365.09
Say 365.10
17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes
and fittings of diameter :
17.58.1 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for one joint
MATERIAL
1397 Pig lead kilogram 0.98 210.00 205.80
SUB HEAD : 17- SANITARY INSTALLATIONS 1449
Code Description Unit Quantity Rate Amount
1881 Spun yarn kilogram 0.11 55.00 6.05
9999 Kerosene oil, fuel and other sundries L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 1.43 2.12 3.03
LABOUR
0116 Fitter (grade 1) day 0.06 784.00 47.04
0117 Assistant Fitter or 2nd class Fitter day 0.06 714.00 42.84
0114 Beldar day 0.12 645.00 77.40
TOTAL 410.82 W
Add 1 % Water charges on "W" 4.11
TOTAL 414.93 X
Add GST on "X" (multiplying
factor 0.1405) 58.30
TOTAL 473.23 Y
Add 15% CPOH on "Y" 70.98
TOTAL 544.21 Z
Add Cess @ 1% on "Z" 5.44
Cost of each 549.66
Say 549.65
17.58.2 75 mm
Code Description Unit Quantity Rate Amount
Details of cost for one joint
MATERIAL
1397 Pig lead kilogram 0.88 210.00 184.80
1881 Spun yarn kilogram 0.09 55.00 4.95
9999 Kerosene oil, fuel and other sundries L.S. 10.79 2.12 22.87
9977 Carriage of materials L.S. 1.43 2.12 3.03
LABOUR
0116 Fitter (grade 1) day 0.05 784.00 39.20
0117 Assistant Fitter or 2nd class Fitter day 0.05 714.00 35.70
0114 Beldar day 0.09 645.00 58.05
TOTAL 348.61 W
Add 1 % Water charges on "W" 3.49
TOTAL 352.09 X
Add GST on "X" (multiplying
factor 0.1405) 49.47
TOTAL 401.56 Y
Add 15% CPOH on "Y" 60.23
TOTAL 461.80 Z
Add Cess @ 1% on "Z" 4.62
Cost of each 466.41
Say 466.40
17.58.3 50 mm
Code Description Unit Quantity Rate Amount
Details of cost for one joint
MATERIAL
1397 Pig lead kilogram 0.77 210.00 161.70
1881 Spun yarn kilogram 0.06 55.00 3.30
SUB HEAD : 17- SANITARY INSTALLATIONS 1450
Code Description Unit Quantity Rate Amount
9999 Kerosene oil, fuel and other sundries L.S. 6.76 2.12 14.33
9977 Carriage of materials L.S. 1.43 2.12 3.03
LABOUR
0116 Fitter (grade 1) day 0.04 784.00 31.36
0117 Assistant Fitter or 2nd class Fitter day 0.05 714.00 35.70
0114 Beldar day 0.05 645.00 32.25
TOTAL 281.67 W
Add 1 % Water charges on "W" 2.82
TOTAL 284.49 X
Add GST on "X" (multiplying
factor 0.1405) 39.97
TOTAL 324.46 Y
Add 15% CPOH on "Y" 48.67
TOTAL 373.13 Z
Add Cess @ 1% on "Z" 3.73
Cost of each 376.86
Say 376.85
17.59 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast
(spun) iron pipes of diameter :
17.59.1 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1330 Clamps and M.S. stays including
bolts and nuts for 100 mm pipe each 1.00 67.50 67.50
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 96.16 W
Add 1 % Water charges on "W" 0.96
TOTAL 97.12 X
Add GST on "X" (multiplying
factor 0.1405) 13.65
TOTAL 110.77 Y
Add 15% CPOH on "Y" 16.62
TOTAL 127.39 Z
Add Cess @ 1% on "Z" 1.27
Cost of each 128.66
Say 128.65
17.59.2 75 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1335 Clamps and M.S. stays including
bolts and nuts for 75 mm pipe each 1.00 37.00 37.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1451
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 59.87 W
Add 1 % Water charges on "W" 0.60
TOTAL 60.47 X
Add GST on "X" (multiplying
factor 0.1405) 8.50
TOTAL 68.97 Y
Add 15% CPOH on "Y" 10.35
TOTAL 79.32 Z
Add Cess @ 1% on "Z" 0.79
Cost of each 80.11
Say 80.10
17.59.3 50 mm
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1334 Clamps and M.S. stays including bolts
and nuts for 50 mm pipe each 1.00 35.00 35.00
9988 Carriage of materials and fixing charges L.S. 9.49 2.12 20.12
TOTAL 55.12 W
Add 1 % Water charges on "W" 0.55
TOTAL 55.67 X
Add GST on "X" (multiplying
factor 0.1405) 7.82
TOTAL 63.49 Y
Add 15% CPOH on "Y" 9.52
TOTAL 73.02 Z
Add Cess @ 1% on "Z" 0.73
Cost of each 73.75
Say 73.75
17.60 Providing and fixing trap of self cleansing design with screwed down or hinged
grating with or without vent arm complete, including cost of cutting and making
good the walls and floors :
17.60.1 100 mm inlet and 100 mm outlet
17.60.1.1 Sand cast iron S&S as per IS: 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7808 Centrifugally cast (spun) iron S&S
100 mm inlet and 100 mm outlet each 1.00 450.00 450.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1452
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.50 645.00 322.50
TOTAL 1198.95 W
Add 1 % Water charges on "W" 11.99
TOTAL 1210.94 X
Add GST on "X" (multiplying
factor 0.1405) 170.14
TOTAL 1381.08 Y
Add 15% CPOH on "Y" 207.16
TOTAL 1588.24 Z
Add Cess @ 1% on "Z" 15.88
Cost of each 1604.12
Say 1604.10
17.60.1.2 Sand Cast Iron S&S as per IS: 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1897 100 mm S.C.I. trap with 100 mm inlet
and 100 mm outlet each 1.00 300.00 300.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1048.95 W
Add 1 % Water charges on "W" 10.49
TOTAL 1059.44 X
Add GST on "X" (multiplying
factor 0.1405) 148.85
TOTAL 1208.29 Y
Add 15% CPOH on "Y" 181.24
TOTAL 1389.53 Z
Add Cess @ 1% on "Z" 13.90
Cost of each 1403.43
Say 1403.45
17.60.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7642 Hubless centrifugally cast (spun) iron
trap with 100 mm inlet and 100 mm
outlet as per IS 15905 each 1.00 540.00 540.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1453
Code Description Unit Quantity Rate Amount
9977 Carriage of materials and fixing
charges L.S. 13.52 2.12 28.66
TOTAL 568.66 W
Add 1 % Water charges on "W" 5.69
TOTAL 574.35 X
Add GST on "X" (multiplying
factor 0.1405) 80.70
TOTAL 655.05 Y
Add 15% CPOH on "Y" 98.26
TOTAL 753.30 Z
Add Cess @ 1% on "Z" 7.53
Cost of each 760.83
Say 760.85
17.60.2 100 mm inlet and 75 mm outlet
17.60.2.1 Sand cast iron S&S as per IS - 3989
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7809 Centrifugally cast (spun) iron S&S
100 mm inlet and 75 mm outlet each 1.00 500.00 500.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 1248.95 W
Add 1 % Water charges on "W" 12.49
TOTAL 1261.44 X
Add GST on "X" (multiplying
factor 0.1405) 177.23
TOTAL 1438.67 Y
Add 15% CPOH on "Y" 215.80
TOTAL 1654.47 Z
Add Cess @ 1% on "Z" 16.54
Cost of each 1671.02
Say 1671.00
17.60.2.2 Sand Cast Iron S&S as per IS- 1729
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1898 100 mm S.C.I. trap with 100 mm inlet
and 75 mm outlet each 1.00 220.00 220.00
9999 Cement, sand and grit etc. L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 2.73 2.12 5.79
SUB HEAD : 17- SANITARY INSTALLATIONS 1454
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 968.95 W
Add 1 % Water charges on "W" 9.69
TOTAL 978.64 X
Add GST on "X" (multiplying
factor 0.1405) 137.50
TOTAL 1116.14 Y
Add 15% CPOH on "Y" 167.42
TOTAL 1283.56 Z
Add Cess @ 1% on "Z" 12.84
Cost of each 1296.39
Say 1296.40
17.60.2.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
Code Description Unit Quantity Rate Amount
Detail of cost for one no.
MATERIAL
7643 Hubless centrifugally cast (spun) iron
trap with 100 mm inlet and 75 mm
outlet as per IS 15905 each 1.00 385.00 385.00
9977 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 413.66 W
Add 1 % Water charges on "W" 4.14
TOTAL 417.80 X
Add GST on "X" (multiplying
factor 0.1405) 58.70
TOTAL 476.50 Y
Add 15% CPOH on "Y" 71.47
TOTAL 547.97 Z
Add Cess @ 1% on "Z" 5.48
Cost of each 553.45
Say 553.45
17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/
centrifugally cast (spun) iron pipes and making good the same with cement
concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm
nominal size), including necessary plaster and pointing in cement mortar 1:4 (1
cement : 4 coarse sand) :
17.61.1 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand :6 graded stone
aggregate )
SUB HEAD : 17- SANITARY INSTALLATIONS 1455
Code Description Unit Quantity Rate Amount
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.022 8843.45 194.56 A
9999 Plastering in cement mortar 1:4 L.S. 10.40 2.12 22.05
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0123 Mason (brick layer) 1st class day 0.14 784.00 109.76
0114 Beldar day 0.27 645.00 174.15
TOTAL 509.33 W
Add 1 % Water charges on "W-A" 3.15
TOTAL 512.48 X
Add GST on "X-A" (multiplying
factor 0.1405) 44.67
TOTAL 557.15 Y
Add 15% CPOH on "Y-A" 54.39
TOTAL 611.54 Z
Add Cess @ 1% on "Z-A" 4.17
Cost of one metre 615.71
Say 615.70
17.61.2 75 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand :6 graded stone
aggregate )
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.015 8843.45 132.65 A
9999 Plastering in cement mortar 1:4 L.S. 7.80 2.12 16.54
9977 Carriage of materials L.S. 3.51 2.12 7.44
LABOUR
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
0114 Beldar day 0.20 645.00 129.00
TOTAL 364.03 W
Add 1 % Water charges on "W-A" 2.31
TOTAL 366.34 X
Add GST on "X-A" (multiplying
factor 0.1405) 32.83
TOTAL 399.18 Y
Add 15% CPOH on "Y-A" 39.98
TOTAL 439.15 Z
Add Cess @ 1% on "Z-A" 3.07
Cost of one metre 442.22
Say 442.20
17.61.3 50 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Cement concrete 1:3:6 (1 cement : 3
coarse sand :6 graded stone aggregate)
SUB HEAD : 17- SANITARY INSTALLATIONS 1456
Code Description Unit Quantity Rate Amount
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.008 8843.45 70.75 A
9999 Plastering in cement mortar 1:4 L.S. 5.20 2.12 11.02
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.07 784.00 54.88
0114 Beldar day 0.14 645.00 90.3
TOTAL 232.74 W
Add 1 % Water charges on "W-A" 1.62
TOTAL 234.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 22.99
TOTAL 257.35 Y
Add 15% CPOH on "Y-A" 27.99
TOTAL 285.34 Z
Add Cess @ 1% on "Z-A" 2.15
Cost of one metre 287.48
Say 287.50
17.62 Painting C.I. cistern with bitumastic or any other anti-corrosive paint inside and
white paint over a coat of zinc chromate yellow primer (of approved quality ) on
the outside surface of the cistern, flush pipe, other fittings, etc. complete for
new work.
Code Description Unit Quantity Rate Amount
Details of cost for one cistern with
fittings
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.23 100.00 23.00
4202 Red oxide Zinc chromate primer litre 0.20 120.00 24.00
0834 Synthetic enamel paint in all shades
except black or chocolate shade litre 0.40 165.00 66.00
9977 Carriage of materials L.S. 1.43 2.12 3.03
9999 Sundries L.S. 6.76 2.12 14.33
LABOUR
0131 Painter day 0.25 714.00 178.50
0114 Beldar day 0.50 645.00 322.50
TOTAL 631.36 W
Add 1 % Water charges on "W" 6.31
TOTAL 637.68 X
Add GST on "X" (multiplying
factor 0.1405) 89.59
TOTAL 727.27 Y
Add 15% CPOH on "Y" 109.09
TOTAL 836.36 Z
Add Cess @ 1% on "Z" 8.36
Cost of each 844.72
Say 844.70
SUB HEAD : 17- SANITARY INSTALLATIONS 1457
17.63 Re-painting C.I. cistern with bitumastic or any other anti-corrosive paint inside
and white paint on the outside surface of the cistern, flush pipe, other fittings,
etc. complete, including polishing of wooden seat and lid and cleaning of W.C.
pan with acid wherever necessary.
Code Description Unit Quantity Rate Amount
Details of cost for one cistern with
fittings
MATERIAL
0828 Anticorrosive bituminous paint (black) litre 0.23 100.00 23.00
0834 Synthetic enamel paint in all shades
except black or chocolate shade litre 0.20 165.00 33.00
9999 Polishing of wooden seat and cleaning
of W.C. pan with acid L.S. 20.67 2.12 43.82
9988 Sundries and carriage of materials L.S. 7.15 2.12 15.16
LABOUR
0131 Painter day 0.20 714.00 142.80
0114 Beldar day 0.25 645.00 161.25
TOTAL 419.03 W
Add 1 % Water charges on "W" 4.19
TOTAL 423.22 X
Add GST on "X" (multiplying
factor 0.1405) 59.46
TOTAL 482.68 Y
Add 15% CPOH on "Y" 72.40
TOTAL 555.08 Z
Add Cess @ 1% on "Z" 5.55
Cost of each 560.63
Say 560.65
17.64 Repainting C.I. cistern with synthetic enamel paint of approved colour, brand
and manufacture on the outside surface of cistern, flush pipe, other fittings etc.
complete.
Code Description Unit Quantity Rate Amount
Details of cost for one cistern with
fittings
MATERIAL
0834 Synthetic enamel paint in all shades
except black or chocolate shade litre 0.20 165.00 33.00
9988 Sundries and carriage of materials L.S. 3.64 2.12 7.72
LABOUR
0131 Painter day 0.09 714.00 64.26
0114 Beldar day 0.12 645.00 77.40
TOTAL 182.38 W
Add 1 % Water charges on "W" 1.82
TOTAL 184.20 X
Add GST on "X" (multiplying
factor 0.1405) 25.88
TOTAL 210.08 Y
Add 15% CPOH on "Y" 31.51
TOTAL 241.59 Z
Add Cess @ 1% on "Z" 2.42
Cost of each 244.01
Say 244.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1458
17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and
fittings with two coats of synthetic enamel paint of any colour such as chocolate
grey, or buff etc. over a coat of primer (of approved quality) for new work :
17.65.1 100 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
Perimeter = 3.14x110 mm =345.71
Area 10x0.3457 = 3.46 sqm
Priming coat
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 3.46 55.50 192.03 A
Painting two coats with paint of any
colour such as chocolatem grey or buff
etc.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 3.46 131.45 454.82 A
9999 Add for delay L.S. 17.16 2.12 36.38
TOTAL 683.23 W
Add 1 % Water charges on "W-A" 0.36
TOTAL 683.59 X
Add GST on "X" (multiplying
factor 0.1405) 5.16
TOTAL 688.75 Y
Add 15% CPOH on "Y-A" 6.29
TOTAL 695.04 Z
Add Cess @ 1% on "Z-A" 0.48
Cost of 10 metres 695.52
Cost of 1 metre 69.55
Say 69.55
17.65.2 75 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
Perimeter = 3.14x82 mm =257.71
Area 10x0.2577 =2.577 sqm
say 2.60 sq. m
for outer surface
Priming coat
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 2.60 55.50 144.30 A
Painting two coats with paint of any
colour such as choclate grey or buff
etc.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 2.60 131.45 341.77 A
SUB HEAD : 17- SANITARY INSTALLATIONS 1459
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 15.21 2.12 32.25
TOTAL 518.32 W
Add 1 % Water charges on "W-A" 0.32
TOTAL 518.64 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.58
TOTAL 523.21 Y
Add 15% CPOH on "Y-A" 5.57
TOTAL 528.78 Z
Add Cess @ 1% on "Z-A" 0.43
Cost of 10 metres 529.21
Cost of 1 metre 52.92
Say 52.90
17.66 Repainting sand cast iron/ centrifugally cast iron (spun) iron, soil, waste, vent
pipes and fittings with one coat of synthetic enamel paint of any colour such as
chocolate, grey or buff etc :
17.66.1 100 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
Painting one coat with paint of any
colour such as chocolate,grey or buff
etc.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 3.46 86.55 299.46 A
9999 Add for delay L.S. 12.22 2.12 25.91
TOTAL 325.37 W
Add 1 % Water charges on "W-A" 0.26
TOTAL 325.63 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.68
TOTAL 329.30 Y
Add 15% CPOH on "Y-A" 4.48
TOTAL 333.78 Z
Add Cess @ 1% on "Z-A" 0.34
Cost of 10 metres 334.12
Cost of 1 metre 33.41
Say 33.40
17.66.2 75 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
Painting one coat with paint of any
colour such as chocolate,grey or buff
etc.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 2.577 86.55 223.04 A
SUB HEAD : 17- SANITARY INSTALLATIONS 1460
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 9.49 2.12 20.12
TOTAL 243.16 W
Add 1 % Water charges on "W-A" 0.20
TOTAL 243.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.85
TOTAL 246.21 Y
Add 15% CPOH on "Y-A" 3.48
TOTAL 249.69 Z
Add Cess @ 1% on "Z-A" 0.27
Cost of 10 metres 249.96
Cost of 1 metre 25.00
Say 25.00
17.67 Repainting bath tub of size 1700x730x430 mm with enamel paint.
Code Description Unit Quantity Rate Amount
Details of cost for one tub
MATERIAL
0833 Synthetic enamel paint in black or
chocolate shade litre 0.90 175.00 157.50
9999 Sundries L.S. 6.76 2.12 14.33
LABOUR
0131 Painter day 0.25 714.00 178.50
0115 Coolie day 0.25 645.00 161.25
TOTAL 511.58 W
Add 1 % Water charges on "W" 5.12
TOTAL 516.70 X
Add GST on "X" (multiplying
factor 0.1405) 72.60
TOTAL 589.29 Y
Add 15% CPOH on "Y" 88.39
TOTAL 677.69 Z
Add Cess @ 1% on "Z" 6.78
Cost of each 684.46
Say 684.45
17.68 Providing and fixing vitreous china dual purpose closet suitable for use as
squatting pan or European type water closet (Anglo Indian W.C pan) with seat &
lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing
cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with
specials of standard make and mosquito proof coupling of approved municipal
design complete, including painting of fittings and brackets, cutting and making
good the walls and floors wherever required:
17.68.1 White vitreous china dual purpose WC pan with white solid plastic seat and lid
with white vitreous china flushing cistern and C.P. flush bend.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1875 White plastic seat (solid)with lid
C.P.brass hinges and rubber buffers each 1.00 410.00 410.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1461
Code Description Unit Quantity Rate Amount
1965 White vitreous china dual purpose
closet (Anglo Indian W.C.) suitable for
use as sequatting pan or European
type water closet as per manufacturer's
specifications each 1.00 2500.00 2500.00
7006 Vitreous china 10 litres low level cistern
with fittings each 1.00 1200.00 1200.00
9999 20 mm G.I.over flow pipe and specials
for over flow pipe L.S. 276.25 2.12 585.65
1350 Mosquito proof coupling of approved
design each 1.00 30.00 30.00
9999 Plugs, screws etc. L.S. 59.15 2.12 125.40
9999 Red lead, white lead and gaskin etc. L.S. 71.76 2.12 152.13
9999 Cement,sand and grit L.S. 118.43 2.12 251.07
9977 Carriage of materials L.S. 118.43 2.12 251.07
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 7718.32 W
Add 1 % Water charges on "W" 77.18
TOTAL 7795.51 X
Add GST on "X" (multiplying
factor 0.1405) 1095.27
TOTAL 8890.77 Y
Add 15% CPOH on "Y" 1333.62
TOTAL 10224.39 Z
Add Cess @ 1% on "Z" 102.24
Cost of each 10326.63
Say 10326.65
17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved
quality and colour.
17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less
than 45 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7491 PTMT Waste Coupling 31/32MM each 1.00 34.00 34.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 76.99 W
Add 1 % Water charges on "W" 0.77
TOTAL 77.76 X
Add GST on "X" (multiplying
factor 0.1405) 10.93
TOTAL 88.69 Y
Add 15% CPOH on "Y" 13.30
TOTAL 101.99 Z
Add Cess @ 1% on "Z" 1.02
Cost of each 103.01
Say 103.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1462
17.69.2 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not
less than 60 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7492 PTMT Waste Coupling 38/40MM each 1.00 39.00 39.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 81.99 W
Add 1 % Water charges on "W" 0.82
TOTAL 82.81 X
Add GST on "X" (multiplying
factor 0.1405) 11.64
TOTAL 94.45 Y
Add 15% CPOH on "Y" 14.17
TOTAL 108.62 Z
Add Cess @ 1% on "Z" 1.09
Cost of each 109.70
Say 109.70
17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.
17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm, effective length
of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with
25 mm minimum water seal, weighing not less than 260 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7493 PTMT Bottle Trap 31/32MM each 1.00 200.00 200.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 242.99 W
Add 1 % Water charges on "W" 2.43
TOTAL 245.42 X
Add GST on "X" (multiplying
factor 0.1405) 34.48
TOTAL 279.91 Y
Add 15% CPOH on "Y" 41.99
TOTAL 321.89 Z
Add Cess @ 1% on "Z" 3.22
Cost of each 325.11
Say 325.10
17.70.2 Bottle trap 38 mm single piece moulded with height of 270 mm, effective length
of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with
25 mm minimum water seal, weighing not less than 263 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7494 PTMT Bottle Trap 38/40MM each 1.00 200.00 200.00
SUB HEAD : 17- SANITARY INSTALLATIONS 1463
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 242.99 W
Add 1 % Water charges on "W" 2.43
TOTAL 245.42 X
Add GST on "X" (multiplying
factor 0.1405) 34.48
TOTAL 279.91 Y
Add 15% CPOH on "Y" 41.99
TOTAL 321.89 Z
Add Cess @ 1% on "Z" 3.22
Cost of each 325.11
Say 325.10
17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and
112 mm distance from wall of standard shape with bracket of the same materials
with snap fittings of approved quality and colour, weighing not less than 105 gms.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7503 PTMT Liquid Soap Container of
400ml capacity each 1.00 95.00 95.00
9988 Carriage of materials and fixing charges L.S. 6.76 2.12 14.33
TOTAL 109.33 W
Add 1 % Water charges on "W" 1.09
TOTAL 110.42 X
Add GST on "X" (multiplying
factor 0.1405) 15.51
TOTAL 125.94 Y
Add 15% CPOH on "Y" 18.89
TOTAL 144.83 Z
Add Cess @ 1% on "Z" 1.45
Cost of each 146.28
Say 146.30
17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm
wide with minimum distances of 37 mm from wall face with concealed fittings
arrangement of approved quality and colour, weighing not less than 88 gms.
Code Description Unit Quantity Rate Amount
MATERIAL
7504 PTMT - Towel Ring 215x200x37mm each 1.00 110.00 110.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 152.99 W
Add 1 % Water charges on “W” 1.53
TOTAL 154.52 X
Add GST on “X” (multiplying
factor 0.1405) 21.71
TOTAL 176.23 Y
Add 15% CPOH on “Y” 26.44
TOTAL 202.67 Z
Add Cess @ 1% on “Z” 2.03
Cost of each 204.70
Say 204.70
SUB HEAD : 17- SANITARY INSTALLATIONS 1464
17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden
cleats with CP brass screws with concealed fittings arrangement of approved
quality and colour.
17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective
height of 88 mm, weighing not less than 170 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7505 PTMT Towel Rail (450mm) each 1.00 125.00 125.00
Wooden cleates
8.23 Rate as per item no 8.23 of
SH : Cladding work each 2.00 35.50 71.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.06 180.00 10.80
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.17 714.00 121.38
0114 Beldar day 0.17 645.00 109.65
TOTAL 446.65 W
Add 1 % Water charges on "W-A" 3.76
TOTAL 450.41 X
Add GST on "X-A" (multiplying
factor 0.1405) 53.31
TOTAL 503.71 Y
Add 15% CPOH on "Y-A" 64.91
TOTAL 568.62 Z
Add Cess @ 1% on "Z-A" 4.98
Cost of each 573.60
Say 573.60
17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective
height of 88 mm, weighing not less than 190 gms.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7506 PTMT Towel Rail (600mm) each 1.00 145.00 145.00
Wooden cleates
8.23 Rate as per item no 8.23 of
SH : Cladding work each 2.00 35.50 71.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.06 180.00 10.80
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.17 714.00 121.38
0114 Beldar day 0.17 645.00 109.65
TOTAL 466.65 W
Add 1 % Water charges on "W-A" 3.96
TOTAL 470.61 X
Add GST on "X-A" (multiplying
factor 0.1405) 56.14
TOTAL 526.75 Y
Add 15% CPOH on "Y-A" 68.36
TOTAL 595.11 Z
Add Cess @ 1% on "Z-A" 5.24
Cost of each 600.35
Say 600.35
SUB HEAD : 17- SANITARY INSTALLATIONS 1465
17.74 Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height
of approved quality and colour, weighing not less than 300 gms.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7507 PTMT Shelf 450x124x36mm each 1.00 150.00 150.00
Wooden cleates
8.23 Rate as per item no 8.23 of
SH : Cladding work each 2.00 35.50 71.00 A
0588 Chromium plated Brass screws 25 mm 100 Nos 0.06 180.00 10.80
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0112 Carpenter 2nd class day 0.17 714.00 121.38
0114 Beldar day 0.17 645.00 109.65
TOTAL 471.65 W
Add 1 % Water charges on "W-A" 4.01
TOTAL 475.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 56.85
TOTAL 532.51 Y
Add 15% CPOH on "Y-A" 69.23
TOTAL 601.74 Z
Add Cess @ 1% on "Z-A" 5.31
Cost of each 607.04
Say 607.05
17.75 Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2"
BSP thread and shapes, weighing not less than 60 gms.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7508 PTMT Urinal Spreader 15mm each 1.00 55.00 55.00
9988 Carriage of materials and fixing charges L.S. 6.76 2.12 14.33
TOTAL 69.33 W
Add 1 % Water charges on "W" 0.69
TOTAL 70.02 X
Add GST on "X" (multiplying
factor 0.1405) 9.84
TOTAL 79.86 Y
Add 15% CPOH on "Y" 11.98
TOTAL 91.84 Z
Add Cess @ 1% on "Z" 0.92
Cost of each 92.76
Say 92.75
SUB HEAD : 17- SANITARY INSTALLATIONS 1466
17.76 Providing and fixing PTMT urinal cock of approved quality and colour.
17.76.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female
threads weighing not less than 48 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7858 P.T.M.T. Urinal cock 15mm dia each 1.00 95.00 95.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 112.09 W
Add 1 % Water charges on "W" 1.12
TOTAL 113.21 X
Add GST on "X" (multiplying
factor 0.1405) 15.91
TOTAL 129.11 Y
Add 15% CPOH on "Y" 19.37
TOTAL 148.48 Z
Add Cess @ 1% on "Z" 1.48
Cost of each 149.97
Say 149.95
17.77 Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/
cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of
specified shape, projecting 75 mm outside the wall surface and fixed on wall
with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes
in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed
to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S.
flats of specified shape and of total length 420 mm and shall be fixed with M.S.
nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.
17.77.1 Total bracket length 580 mm of approved shape and design (for single 100 mm
dia pipe)
Code Description Unit Quantity Rate Amount
Details of cost for 5 nos.
MATERIAL
M.S. flats 50x5mm 5 x 0.58 = 2.90m
@ 1.97 kg/ metre = 5.71 kg.
M.S. flats 30x1.6mm 5x0.42 = 2.10m.
0.38kg/metre = 0.80kg.
Total = 6.51kg.
Add wastage 5% = 0.33kg.
Total = 6.86 kg.= 0.0686 quintal
1007 Structurals such as tees,angles
channels and R.S. joists quintal 0.0686 4950.00 339.57
2205 Carriage of Steel tonne 0.0068 145.72 0.99
LABOUR
0116 Fitter (grade 1) day 0.033 784.00 25.87
0103 Blacksmith 2nd class day 0.049 714.00 34.99
0114 Beldar day 0.065 645.00 41.93
priming coat
5x0.58x0.11 = 0.32
5x0.42x0.063 = 0.13
Total=0.45sqm
SUB HEAD : 17- SANITARY INSTALLATIONS 1467
Code Description Unit Quantity Rate Amount
13.50.1 Rate as per item no 13.50.1 of
SH : Finishing sqm 0.45 61.45 27.65 A
9999 Sundries L.S. 1.35 2.12 2.86
P/F expansion hold fasteners 6mm
threaded dia 5x4 Nos = 20 nos.
8.8.1.1 Rate asper item no. 8.8.1.1 of
SH :- Marble work each 20.00 30.75 615.00 A
TOTAL 1088.86 W
Add 1 % Water charges on "W-A" 4.46
TOTAL 1093.32 X
Add GST on "X-A" (multiplying
factor 0.1405) 63.32
TOTAL 1156.64 Y
Add 15% CPOH on "Y-A" 77.10
TOTAL 1233.74 Z
Add Cess @ 1% on "Z-A" 5.91
Cost of 5 Nos. 1239.65
Cost of each 247.93
Say 247.95
17.77.2 Total bracket length 810 mm of approved shape and design (for two 100 mm dia
pipes)
Code Description Unit Quantity Rate Amount
Details of cost for 5 nos.
MATERIAL
M.S. flats 50x5mm 5 x 0.81 = 4.05m
@ 1.97 kg/ metre = 7.98 kg.
M.S. flats 30x1.6mm 5x2x0.42 = 4.20m.
0.38kg/metre = 1.60kg.
Total = 9.58kg.
Add wastage 5% = 0.48kg.
Total = 10.06 kg.
M.S.flats 10.06kg. = 0.1006 quintal
1007 Structurals such as tees,angles
channels and R.S. joists quintal 0.1006 4950.00 497.97
2205 Carriage of Steel tonne 0.01006 145.72 1.47
LABOUR
0116 Fitter (grade 1) day 0.048 784.00 37.63
0103 Blacksmith 2nd class day 0.072 714.00 51.41
0114 Beldar day 0.096 645.00 61.92
priming coat
5x0.81x0.11 = 0.45
5x2x0.42x0.063 = 0.26
Total =0.71sqm
13.50.1 Rate as per item no 13.50.1 of
SH : Finishing sqm 0.71 61.45 43.63 A
9999 Sundries L.S. 1.98 2.12 4.20
P/F expansion hold fasteners 6mm
threaded dia 5x4 Nos = 20 nos.
SUB HEAD : 17- SANITARY INSTALLATIONS 1468
Code Description Unit Quantity Rate Amount
8.8.1.1 Rate asper item no. 8.8.1.1 of
SH :- Marble work each 20.00 30.75 615.00 A
TOTAL 1313.22 W
Add 1 % Water charges on "W-A" 6.55
TOTAL 1319.77 X
Add GST on "X-A" (multiplying
factor 0.1405) 92.89
TOTAL 1412.66 Y
Add 15% CPOH on "Y-A" 113.10
TOTAL 1525.76 Z
Add Cess @ 1% on "Z-A" 8.67
Cost of 5 Nos. 1534.43
Cost of each 306.89
Say 306.90
17.77.3 Total bracket length 1040 mm of approved shape and design (for three 100 mm
dia pipes)
Code Description Unit Quantity Rate Amount
Details of cost for 5 nos.
MATERIAL
M.S. flats 50x5mm 5 x 1.04= 5.20m
@ 1.97 kg/ metre = 10.24 kg.
M.S. flats 30x1.6mm 5x3x0.42 = 6.30m.
0.38kg/metre = 2.39kg.
Total = 12.63kg.
Add wastage 5% = 0.63kg.
Total = 13.26 kg.
M.S.flats 13.26kg. = 0.1326 quintal
1007 Structurals such as tees,angles
channels and R.S. joists quintal 0.1326 4950.00 656.37
2205 Carriage of Steel tonne 0.01326 145.72 1.93
LABOUR
0116 Fitter (grade 1) day 0.063 784.00 49.39
0103 Blacksmith 2nd class day 0.095 714.00 67.83
0114 Beldar day 0.126 645.00 81.27
priming coat
5x1.04x0.11 = 0.57
5x3x0.42x0.063 = 0.40
Total=0.97sqm
13.50.1 Rate as per item no 13.50.1 of
SH : Finishing sqm 0.97 61.45 59.61 A
9999 Sundries L.S. 2.60 2.12 5.51
P/F expansion hold fasteners 6mm
threaded dia 5x4 Nos = 20 nos.
SUB HEAD : 17- SANITARY INSTALLATIONS 1469
Code Description Unit Quantity Rate Amount
8.8.1.1 Rate asper item no. 8.8.1.1 of
SH :- Marble work each 20.00 30.75 615.00 A
TOTAL 1536.91 W
Add 1 % Water charges on "W-A" 8.62
TOTAL 1545.54 X
Add GST on "X-A" (multiplying
factor 0.1405) 122.37
TOTAL 1667.90 Y
Add 15% CPOH on "Y-A" 148.99
TOTAL 1816.90 Z
Add Cess @ 1% on "Z-A" 11.42
Cost of 5 Nos. 1828.32
Cost of each 365.66
Say 365.65
17.78 Providing and fixing white vitreous china extended wall mounting water closet
of size 780x370x690 mm of approved shape including providing & fixing white
vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre
(adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts,
bolts and gasket etc complete.
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
7072 Wall mounted water closet each 1.00 5500.00 5500.00
7073 Adjustable Vetrious China Cistern with
fittings each 1.00 1600.00 1600.00
1875 White plastic seat (solid)with lid
C.P.brass hinges and rubber buffers each 1.00 410.00 410.00
9977 Carriage of materials L.S. 9.79 2.12 20.75
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 9743.75 W
Add 1 % Water charges on "W" 97.44
TOTAL 9841.19 X
Add GST on "X" (multiplying
factor 0.1405) 1382.69
TOTAL 11223.88 Y
Add 15% CPOH on "Y" 1683.58
TOTAL 12907.46 Z
Add Cess @ 1% on "Z" 129.07
Cost of each 13036.54
Say 13036.55
SUB HEAD : 17- SANITARY INSTALLATIONS 1470
17.79 Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315
mm having antibacterial /germs free ceramic surface, fixed with cartridge having
debris catcher and hygiene seal.
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
7074 White Vetrious China Waterless Urinal each 1.00 9000.00 9000.00
7075 Cistern with fittings for Waterless Urinal each 1.00 2200.00 2200.00
9977 Carriage of materials L.S. 9.79 2.12 20.75
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 11935.25 W
Add 1 % Water charges on "W" 119.35
TOTAL 12054.61 X
Add GST on "X" (multiplying
factor 0.1405) 1693.67
TOTAL 13748.28 Y
Add 15% CPOH on "Y" 2062.24
TOTAL 15810.52 Z
Add Cess @ 1% on "Z" 158.11
Cost of each 15968.63
Say 15968.65
17.80 Providing and fixing white vitreous china battery based infrared sensor operated
urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water
(250 ml & 500 ml consumption), having water inlet from back side, including
fixing to wall with suitable brackets all as per manufacturers specification and
direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for one pan
MATERIAL
7076 White Vetrious Urinal each 1.00 4500.00 4500.00
9977 Carriage of materials L.S. 9.79 2.12 20.75
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 5235.25 W
Add 1 % Water charges on "W" 52.35
TOTAL 5287.61 X
Add GST on "X" (multiplying
factor 0.1405) 742.91
TOTAL 6030.52 Y
Add 15% CPOH on "Y" 904.58
TOTAL 6935.09 Z
Add Cess @ 1% on "Z" 69.35
Cost of each 7004.44
Say 7004.45
SUB HEAD : 17- SANITARY INSTALLATIONS 1471
17.81 Providing and fixing floor mounted, white vitreous china single piece, double
traps syphonic water closet of approved brand/make, shape, size and pattern
including integrated white vitreous china cistern of capacity 10 litres with dual
flushing system, including all fittings and fixtures with seat cover, cistern fittings,
nuts, bolts and gasket etc including making connection with the existing P/S
trap, complete in all respect as per directions of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
1966 Floor mounted, white vitreous china
single piece, double traps syphonic
water closet of approved brand/make,
shape, size and pattern including
integrated white vitreous china cistern
of capacity 10 litres with dual flushing
system including all fittings and
fixtures with seat cover, cistern
fittings, nuts, bolts and gasket etc. each 1.00 9800.00 9800.00
9977 Carriage of material L.S. 9.79 2.12 20.75
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
TOTAL 12033.75 W
Add 1 % Water charges on "W" 120.34
TOTAL 12154.09 X
Add GST on "X" (multiplying
factor 0.1405) 1707.65
TOTAL 13861.74 Y
Add 15% CPOH on "Y" 2079.26
TOTAL 15941.00 Z
Add Cess @ 1% on "Z" 159.41
Cost of each 16100.41
Say 16100.40
SUB HEAD : 17- SANITARY INSTALLATIONS 1472
SUB HEAD : 18.0
WATER SUPPLY
1473
18.1 Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE
Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water supply, capable to withstand
temperature up to 80°C, including all special fittings of composite material
(engineering plastic blend and brass inserts wherever required) e.g. elbows,
tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing.
This includes testing of joints complete as per direction of the Engineer-in-
charge.
INTERNAL WORK - EXPOSED ON WALL
18.1.1 1216 (16 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8300 1216 mm PE-AL-PE Composit pressure
pipe metre 10.00 80.00 800.00 P
Add 30% for fittings and wastage etc.
on (P) 240.00
30 x P / 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 2201.45 W
Add 1 % Water charges on "W" 22.01
TOTAL 2223.46 X
Add GST on "X" (multiplying
factor 0.1405) 312.40
TOTAL 2535.86 Y
Add 15% CPOH on "Y" 380.38
TOTAL 2916.24 Z
Add Cess @ 1% on "Z" 29.16
Cost of 10 metre 2945.40
Cost of 1 metre 294.54
Say 294.55
18.1.2 1620 (20 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8301 1620 mm PE-AL-PE Composit pressure
pipe metre 10.00 90.00 900.00 P
Add 30% for fittings and wastage etc.
on (P) 270.00
30 x P / 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.82 714.00 585.48
SUB HEAD : 18- WATER SUPPLY 1475
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 2445.69 W
Add 1 % Water charges on "W" 24.46
TOTAL 2470.14 X
Add GST on "X" (multiplying
factor 0.1405) 347.06
TOTAL 2817.20 Y
Add 15% CPOH on "Y" 422.58
TOTAL 3239.78 Z
Add Cess @ 1% on "Z" 32.40
Cost of 10 metre 3272.18
Cost of 1 metre 327.22
Say 327.20
18.1.3 2025 (25 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8302 2025 mm PE-AL-PE Composit pressure
pipe metre 10.00 140.00 1400.00 P
Add 30% for fittings and wastage etc.
on (P) 420.00
30 x P / 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.66 645.00 425.70
TOTAL 3209.93 W
Add 1 % Water charges on "W" 32.10
TOTAL 3242.03 X
Add GST on "X" (multiplying
factor 0.1405) 455.50
TOTAL 3697.53 Y
Add 15% CPOH on "Y" 554.63
TOTAL 4252.16 Z
Add Cess @ 1% on "Z" 42.52
Cost of 10 metre 4294.68
Cost of 1 metre 429.47
Say 429.45
18.1.4 2532 (32 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8303 2532 mm PE-AL-PE Composit pressure
pipe metre 10.00 180.00 1800.00 P
Add 30% for fittings and wastage etc.
on (P) 540.00
30 x P / 100
9999 Cement, sand and grit L.S. 4.16 2.12 8.82
SUB HEAD : 18- WATER SUPPLY 1476
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.98 645.00 632.10
TOTAL 3939.36 W
Add 1 % Water charges on "W" 39.39
TOTAL 3978.75 X
Add GST on "X" (multiplying
factor 0.1405) 559.01
TOTAL 4537.77 Y
Add 15% CPOH on "Y" 680.67
TOTAL 5218.43 Z
Add Cess @ 1% on "Z" 52.18
Cost of 10 metre 5270.62
Cost of 1 metre 527.06
Say 527.05
18.1.5 3240 (40 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8304 3240 mm PE-AL-PE Composit
pressure pipe metre 10.00 280.00 2800.00 P
Add 30% for fittings and wastage
etc. on (P) 840.00
30 x P / 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 5690.31 W
Add 1 % Water charges on "W" 56.90
TOTAL 5747.21 X
Add GST on "X" (multiplying
factor 0.1405) 807.48
TOTAL 6554.70 Y
Add 15% CPOH on "Y" 983.20
TOTAL 7537.90 Z
Add Cess @ 1% on "Z" 75.38
Cost of 10 metre 7613.28
Cost of 1 metre 761.33
Say 761.35
18.1.6 4050 (50 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8305 4050 mm PE-AL-PE Composit
pressure pipe metre 10.00 360.00 3600.00 P
SUB HEAD : 18- WATER SUPPLY 1477
Code Description Unit Quantity Rate Amount
Add 30% for fittings and wastage
etc. on (P) 1080.00
30 x P / 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 6730.31 W
Add 1 % Water charges on "W" 67.30
TOTAL 6797.61 X
Add GST on "X" (multiplying
factor 0.1405) 955.06
TOTAL 7752.68 Y
Add 15% CPOH on "Y" 1162.90
TOTAL 8915.58 Z
Add Cess @ 1% on "Z" 89.16
Cost of 10 metre 9004.73
Cost of 1 metre 900.47
Say 900.45
18.2 Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE
Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water supply, capable to withstand
temperature up to 80°C, including all special fittings of composite material
(engineering plastic blend and brass inserts wherever required) e.g. elbows,
tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing.
This includes the costs of cutting chases and including testing of joints
complete as per direction of the engineer in charge.
Concealed work, including cutting chases and making good the wall etc.
18.2.1 1216 (16 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8300 1216 mm PE-AL-PE Composit
pressure pipe metre 10.00 80.00 800.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 600.00
75 x P / 100
Making chases upto 7.5 x 7.5 cm. in
walls and making good the same
18.78 Rate as per item no. 18.78 of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1478
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.7
TOTAL 4273.66 W
Add 1 % Water charges on "W-A" 25.56
TOTAL 4299.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 362.66
TOTAL 4661.88 Y
Add 15% CPOH on "Y-A" 441.58
TOTAL 5103.46 Z
Add Cess @ 1% on "Z-A" 33.85
Cost of 10 metre 5137.31
Cost of 1 metre 513.73
Say 513.75
18.2.2 1620 (20 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8301 1620 mm PE-AL-PE Composit
pressure pipe metre 10.00 90.00 900.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 675.00
75 * P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 of
SH: water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4448.66 W
Add 1 % Water charges on "W-A" 27.31
TOTAL 4475.97 X
Add GST on "X-A" (multiplying
factor 0.1405) 387.49
TOTAL 4863.46 Y
Add 15% CPOH on "Y-A" 471.82
TOTAL 5335.28 Z
Add Cess @ 1% on "Z-A" 36.17
Cost of 10 metre 5371.45
Cost of 1 metre 537.15
Say 537.15
18.2.3 2025 (25 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8302 2025 mm PE-AL-PE Composit
pressure pipe metre 10.00 140.00 1400.00 P
SUB HEAD : 18- WATER SUPPLY 1479
Code Description Unit Quantity Rate Amount
Add 75% for fittings, clamps and
wastage etc. on (P) 1050.00
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 5323.66 W
Add 1 % Water charges on "W-A" 36.06
TOTAL 5359.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 511.66
TOTAL 5871.38 Y
Add 15% CPOH on "Y-A" 623.01
TOTAL 6494.38 Z
Add Cess @ 1% on "Z-A" 47.76
Cost of 10 metre 6542.15
Cost of 1 metre 654.21
Say 654.20
18.2.4 2532 (32 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8303 2532 mm PE-AL-PE Composit
pressure pipe metre 10.00 180.00 1800.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 1350.00
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 6023.66 W
Add 1 % Water charges on "W-A" 43.06
TOTAL 6066.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 610.99
TOTAL 6677.71 Y
Add 15% CPOH on "Y-A" 743.96
TOTAL 7421.67 Z
Add Cess @ 1% on "Z-A" 57.04
Cost of 10 metre 7478.70
Cost of 1 metre 747.87
Say 747.85
SUB HEAD : 18- WATER SUPPLY 1480
18.3 Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE
Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water supply, capable to withstand
temperature up to 80°C, including all special fittings of composite material
(engineering plastic blend and brass inserts wherever required) e.g. elbows,
tees, reducers, couplers & connectors etc., with trenching, refilling and testing
of joints complete as per direction of the engineer in charge.
External work
18.3.1 1216 (16 mm OD) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8300 1216 mm PE-AL-PE Composit
pressure pipe metre 10.00 80.00 800.00 P
Add 30% for fittings and wastage
etc. on (P) 240.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2057.32 W
Add 1 % Water charges on "W" 20.57
TOTAL 2077.89 X
Add GST on "X" (multiplying
factor 0.1405) 291.94
TOTAL 2369.84 Y
Add 15% CPOH on "Y" 355.48
TOTAL 2725.31 Z
Add Cess @ 1% on "Z" 27.25
Cost of 10 metre 2752.57
Cost of 1 metre 275.26
Say 275.25
18.3.2 1620 (20 mm OD ) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8301 1620 mm PE-AL-PE Composit
pressure pipe metre 10.00 90.00 900.00 P
Add 30% for fittings and wastage
etc. on (P) 270.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
SUB HEAD : 18- WATER SUPPLY 1481
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.66 645.00 425.70
TOTAL 2187.32 W
Add 1 % Water charges on "W" 21.87
TOTAL 2209.19 X
Add GST on "X" (multiplying
factor 0.1405) 310.39
TOTAL 2519.58 Y
Add 15% CPOH on "Y" 377.94
TOTAL 2897.52 Z
Add Cess @ 1% on "Z" 28.98
Cost of 10 metre 2926.50
Cost of 1 metre 292.65
Say 292.65
18.3.3 2025 (25 mm OD ) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8302 2025 mm PE-AL-PE Composit
pressure pipe metre 10.00 140.00 1400.00 P
Add 30% for fittings and wastage
etc. on (P) 420.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2837.32 W
Add 1 % Water charges on “W” 28.37
TOTAL 2865.69 X
Add GST on “X” (multiplying
factor 0.1405) 402.63
TOTAL 3268.32 Y
Add 15% CPOH on “Y” 490.25
TOTAL 3758.57 Z
Add Cess @ 1% on “Z” 37.59
Cost of 10 metre 3796.16
Cost of 1 metre 379.62
Say 379.60
18.3.4 2532 (32 mm OD ) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8303 2532 mm PE-AL-PE Composit
pressure pipe metre 10.00 180.00 1800.00 P
Add 30% for fittings and wastage
etc. on (P) 540.00
30 x P / 100
SUB HEAD : 18- WATER SUPPLY 1482
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 3357.32 W
Add 1 % Water charges on "W" 33.57
TOTAL 3390.89 X
Add GST on "X" (multiplying
factor 0.1405) 476.42
TOTAL 3867.31 Y
Add 15% CPOH on "Y" 580.10
TOTAL 4447.41 Z
Add Cess @ 1% on "Z" 44.47
Cost of 10 metre 4491.88
Cost of 1 metre 449.19
Say 449.20
18.3.5 3240 (40 mm OD ) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8304 3240 mm PE-AL-PE Composit
pressure pipe metre 10.00 280.00 2800.00 P
Add 30% for fittings and wastage
etc. on (P) 840.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 4829.69 W
Add 1 % Water charges on "W" 48.30
TOTAL 4877.99 X
Add GST on "X" (multiplying
factor 0.1405) 685.36
TOTAL 5563.34 Y
Add 15% CPOH on "Y" 834.50
TOTAL 6397.85 Z
Add Cess @ 1% on "Z" 63.98
Cost of 10 metre 6461.82
Cost of 1 metre 646.18
Say 646.20
SUB HEAD : 18- WATER SUPPLY 1483
18.3.6 4050 (50 mm OD ) pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8305 4050 mm PE-AL-PE Composit
pressure pipe metre 10.00 360.00 3600.00 P
Add 30% for fittings and wastage
etc. on (P) 1080.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 5869.69 W
Add 1 % Water charges on "W" 58.70
TOTAL 5928.39 X
Add GST on "X" (multiplying
factor 0.1405) 832.94
TOTAL 6761.33 Y
Add 15% CPOH on "Y" 1014.20
TOTAL 7775.52 Z
Add Cess @ 1% on "Z" 77.76
Cost of 10 metre 7853.28
Cost of 1 metre 785.33
Say 785.35
18.4 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes
confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having
thermal stability for hot & cold water supply, including all PP - R plain & brass
threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00
m spacing. This includes testing of joints complete as per direction of Engineer-
in-Charge.
Internal Exposed on walls
18.4.1 PN - 16 Pipe, 20mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8626 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 20 mm Outer dia metre 10.00 48.46 484.60 P
Add 30% for fittings, clamps and
wastage etc. on P, 30xP/100 145.38
9999 Cement, Sand and grit L.S. 2.73 2.12 5.79
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.82 714.00 585.48
SUB HEAD : 18- WATER SUPPLY 1484
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 1905.67 W
Add 1 % Water charges on "W" 19.06
TOTAL 1924.72 X
Add GST on "X" (multiplying
factor 0.1405) 270.42
TOTAL 2195.15 Y
Add 15% CPOH on "Y" 329.27
TOTAL 2524.42 Z
Add Cess @ 1% on "Z" 25.24
Cost of 10 metre 2549.66
Cost of 1 metre 254.97
Say 254.95
18.4.2 PN - 16 Pipe, 25mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8627 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 25 mm Outer dia metre 10.00 74.82 748.20 P
Add 30% for fittings, clamps and
wastage etc. on P, 30xP/100 224.46
9999 Cement,Sand and grit L.S. 2.73 2.12 5.79
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.66 645.00 425.70
TOTAL 2362.59 W
Add 1 % Water charges on "W" 23.63
TOTAL 2386.21 X
Add GST on "X" (multiplying
factor 0.1405) 335.26
TOTAL 2721.48 Y
Add 15% CPOH on "Y" 408.22
TOTAL 3129.70 Z
Add Cess @ 1% on "Z" 31.30
Cost of 10 metre 3160.99
Cost of 1 metre 316.10
Say 316.10
18.4.3 PN - 16 Pipe, 32mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8628 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 32 mm Outer dia metre 10.00 107.47 1074.70 P
Add 20% for fittings, clamps and
wastage etc. on P, 20xP/100 214.94
9999 Cement, Sand and grit L.S. 4.16 2.12 8.82
SUB HEAD : 18- WATER SUPPLY 1485
Code Description Unit Quantity Rate Amount
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.66 645.00 425.70
TOTAL 2682.60 W
Add 1 % Water charges on "W" 26.83
TOTAL 2709.43 X
Add GST on "X" (multiplying
factor 0.1405) 380.67
TOTAL 3090.10 Y
Add 15% CPOH on "Y" 463.51
TOTAL 3553.61 Z
Add Cess @ 1% on "Z" 35.54
Cost of 10 metre 3589.15
Cost of 1 metre 358.92
Say 358.90
18.4.4 PN - 16 Pipe, 40mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8629 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 40 mm Outer dia metre 10.00 162.00 1620.00 P
Add 15% for fittings, clamps and
wastage etc. on P, 15xP/100 243.00
9999 Cement, Sand and grit L.S. 5.33 2.12 11.30
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 3913.31 W
Add 1 % Water charges on "W" 39.13
TOTAL 3952.44 X
Add GST on "X" (multiplying
factor 0.1405) 555.32
TOTAL 4507.76 Y
Add 15% CPOH on "Y" 676.16
TOTAL 5183.93 Z
Add Cess @ 1% on "Z" 51.84
Cost of 10 metre 5235.76
Cost of 1 metre 523.58
Say 523.60
SUB HEAD : 18- WATER SUPPLY 1486
18.4.5 PN - 10 Pipe, 50mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8630 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
50 mm Outer dia metre 10.00 255.00 2550.00 P
Add 15% for fittings, clamps and
wastage etc. on P, 15xP/100 382.50
9999 Cement, Sand and grit L.S. 5.33 2.12 11.30
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 4982.81 W
Add 1 % Water charges on "W" 49.83
TOTAL 5032.64 X
Add GST on "X" (multiplying
factor 0.1405) 707.09
TOTAL 5739.72 Y
Add 15% CPOH on "Y" 860.96
TOTAL 6600.68 Z
Add Cess @ 1% on "Z" 66.01
Cost of 10 metre 6666.69
Cost of 1 metre 666.67
Say 666.65
18.5 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes
confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having
thermal stability for hot & cold water supply, including all PP - R plain & brass
threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00
m spacing. This includes the cost of cutting chases and making good the
same including testing of joints complete as per direction of Engineer-in-
Charge.
Concealed work,including cutting chases and making good the wall etc.
18.5.1 PN - 16 Pipe, 20mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8626 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 20 mm Outer dia metre 10.00 48.46 484.60 P
Add 75% for fittings, clamps and
wastage etc. on P, 75xP/100 363.45
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per Item Number 18.78 of
SH: Water supply metre 10.00 171.80 1718.00 A
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1487
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 3721.71 W
Add 1 % Water charges on "W-A" 20.04
TOTAL 3741.75 X
Add GST on "X-A" (multiplying
factor 0.1405) 284.34
TOTAL 4026.08 Y
Add 15% CPOH on "Y-A" 346.21
TOTAL 4372.30 Z
Add Cess @ 1% on "Z-A" 26.54
Cost of 10 metre 4398.84
Cost of 1 metre 439.88
Say 439.90
18.5.2 PN - 16 Pipe, 25mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8627 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 25 mm Outer dia metre 10.00 74.82 748.20 P
Add 75% for fittings, clamps and
wastage etc. on P, 75xP/100 561.15
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per Item Number 18.78 of
SH: Water supply metre 10.00 171.80 1718.00 A
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4183.01 W
Add 1 % Water charges on "W-A" 24.65
TOTAL 4207.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 349.80
TOTAL 4557.46 Y
Add 15% CPOH on "Y-A" 425.92
TOTAL 4983.38 Z
Add Cess @ 1% on "Z-A" 32.65
Cost of 10 metre 5016.03
Cost of 1 metre 501.60
Say 501.60
SUB HEAD : 18- WATER SUPPLY 1488
18.5.3 PN - 16 Pipe, 32mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8628 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 32 mm Outer dia metre 10.00 107.47 1074.70 P
Add 50% for fittings, clamps and
wastage etc. on P, 50xP/100 537.35
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per Item Number 18.78 of
SH: Water supply metre 10.00 171.80 1718.00 A
LABOUR:
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4485.71 W
Add 1 % Water charges on "W-A" 27.68
TOTAL 4513.39 X
Add GST on "X-A" (multiplying
factor 0.1405) 392.75
TOTAL 4906.14 Y
Add 15% CPOH on "Y-A" 478.22
TOTAL 5384.36 Z
Add Cess @ 1% on "Z-A" 36.66
Cost of 10 metre 5421.02
Cost of 1 metre 542.10
Say 542.10
18.6 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes
confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having
thermal stability for hot & cold water supply, including all PP - R plain & brass
threaded polypropylene random fittings, including trenching, refilling & testing
of joints complete as per direction of Engineer-in-Charge.
External work
18.6.1 PN - 16 Pipe, 20mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8626 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 20 mm Outer dia metre 10.00 48.46 484.60 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 96.92
LABOUR:
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
SUB HEAD : 18- WATER SUPPLY 1489
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.66 645.00 425.70
TOTAL 1598.84 W
Add 1 % Water charges on "W" 15.99
TOTAL 1614.83 X
Add GST on "X" (multiplying
factor 0.1405) 226.88
TOTAL 1841.71 Y
Add 15% CPOH on "Y" 276.26
TOTAL 2117.97 Z
Add Cess @ 1% on "Z" 21.18
Cost of 10 metre 2139.15
Cost of 1 metre 213.91
Say 213.90
18.6.2 PN - 16 Pipe, 25 mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8627 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 25 mm Outer dia metre 10.00 74.82 748.20 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 149.64
LABOUR:
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2004.57 W
Add 1 % Water charges on "W" 20.05
TOTAL 2024.62 X
Add GST on "X" (multiplying
factor 0.1405) 284.46
TOTAL 2309.07 Y
Add 15% CPOH on "Y" 346.36
TOTAL 2655.44 Z
Add Cess @ 1% on "Z" 26.55
Cost of 10 metre 2681.99
Cost of 1 metre 268.20
Say 268.20
18.6.3 PN - 16 Pipe, 32 mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8628 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 32 mm Outer dia metre 10.00 107.47 1074.70 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 214.94
SUB HEAD : 18- WATER SUPPLY 1490
Code Description Unit Quantity Rate Amount
LABOUR:
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2396.37 W
Add 1 % Water charges on "W" 23.96
TOTAL 2420.33 X
Add GST on "X" (multiplying
factor 0.1405) 340.06
TOTAL 2760.39 Y
Add 15% CPOH on "Y" 414.06
TOTAL 3174.45 Z
Add Cess @ 1% on "Z" 31.74
Cost of 10 metre 3206.19
Cost of 1 metre 320.62
Say 320.60
18.6.4 PN - 16 Pipe, 40 mm OD (SDR-7.4)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8629 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-16 (SDR 7.4)
- 40 mm Outer dia metre 10.00 162.00 1620.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 324.00
LABOUR:
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 3133.69 W
Add 1 % Water charges on "W" 31.34
TOTAL 3165.03 X
Add GST on "X" (multiplying
factor 0.1405) 444.69
TOTAL 3609.71 Y
Add 15% CPOH on "Y" 541.46
TOTAL 4151.17 Z
Add Cess @ 1% on "Z" 41.51
Cost of 10 metre 4192.68
Cost of 1 metre 419.27
Say 419.25
SUB HEAD : 18- WATER SUPPLY 1491
18.6.5 PN - 10 Pipe, 50 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8630 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
50 mm Outer dia metre 10.00 255.00 2550.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 510.00
LABOUR:
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 4249.69 W
Add 1 % Water charges on "W" 42.50
TOTAL 4292.19 X
Add GST on "X" (multiplying
factor 0.1405) 603.05
TOTAL 4895.24 Y
Add 15% CPOH on "Y" 734.29
TOTAL 5629.53 Z
Add Cess @ 1% on "Z" 56.30
Cost of 10 metre 5685.82
Cost of 1 metre 568.58
Say 568.60
18.6.6 PN - 10 Pipe, 63 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8631 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
63 mm Outer dia metre 10.00 285.00 2850.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 570.00
LABOUR:
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 coolie day 0.66 645.00 425.70
TOTAL 4893.10 W
Add 1 % Water charges on "W" 48.93
TOTAL 4942.03 X
Add GST on "X" (multiplying
factor 0.1405) 694.36
TOTAL 5636.39 Y
Add 15% CPOH on "Y" 845.46
TOTAL 6481.84 Z
Add Cess @ 1% on "Z" 64.82
Cost of 10 metre 6546.66
Cost of 1 metre 654.67
Say 654.65
SUB HEAD : 18- WATER SUPPLY 1492
18.6.7 PN - 10 Pipe, 75 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8632 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
75 mm Outer dia metre 10.00 425.00 4250.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 850.00
LABOUR:
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 6573.10 W
Add 1 % Water charges on "W" 65.73
TOTAL 6638.83 X
Add GST on "X" (multiplying
factor 0.1405) 932.76
TOTAL 7571.59 Y
Add 15% CPOH on "Y" 1135.74
TOTAL 8707.32 Z
Add Cess @ 1% on "Z" 87.07
Cost of 10 metre 8794.40
Cost of 1 metre 879.44
Say 879.45
18.6.8 PN - 10 Pipe, 90 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8633 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
90 mm Outer dia metre 10.00 600.00 6000.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 1200.00
LABOUR:
0116 Fitter (grade 1) day 0.37 784.00 290.08
0114 Beldar day 0.97 645.00 625.65
Trenching and refilling etc.
0114 Beldar day 0.80 645.00 516.00
0115 Beldar day 0.80 645.00 516.00
TOTAL 9147.73 W
Add 1 % Water charges on "W" 91.48
TOTAL 9239.21 X
Add GST on "X" (multiplying
factor 0.1405) 1298.11
TOTAL 10537.32 Y
Add 15% CPOH on "Y" 1580.60
TOTAL 12117.91 Z
Add Cess @ 1% on "Z" 121.18
Cost of 10 metre 12239.09
Cost of 1 metre 1223.91
Say 1223.90
SUB HEAD : 18- WATER SUPPLY 1493
18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8634 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
110 mm Outer dia metre 10.00 890.00 8900.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 1780.00
LABOUR:
0116 Fitter (grade 1) day 0.37 784.00 290.08
0114 Beldar day 0.97 645.00 625.65
Trenching and refilling etc.
0114 Beldar day 0.80 645.00 516.00
0115 Coolie day 0.80 645.00 516.00
TOTAL 12627.73 W
Add 1 % Water charges on "W" 126.28
TOTAL 12754.01 X
Add GST on "X" (multiplying
factor 0.1405) 1791.94
TOTAL 14545.95 Y
Add 15% CPOH on "Y" 2181.89
TOTAL 16727.84 Z
Add Cess @ 1% on "Z" 167.28
Cost of 10 metre 16895.12
Cost of 1 metre 1689.51
Say 1689.50
18.6.10 PN - 10 Pipe, 160 mm OD (SDR-11)
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL:
8635 Poly propylene- Random - Co -
Polymer (PPR) pipes PN-10 (SDR 11) -
160 mm Outer dia metre 10.00 2575.00 25750.00 P
Add 20% for fittings and wastage etc.
on P, 20xP/100 5150.00
LABOUR:
0116 Fitter (grade 1) day 0.58 784.00 454.72
0114 Beldar day 1.54 645.00 993.30
Trenching and refilling etc.
0114 Beldar day 1.20 645.00 774.00
0115 Coolie day 1.20 645.00 774.00
TOTAL 33896.02 W
Add 1 % Water charges on "W" 338.96
TOTAL 34234.98 X
Add GST on "X" (multiplying
factor 0.1405) 4810.01
TOTAL 39044.99 Y
Add 15% CPOH on "Y" 5856.75
TOTAL 44901.74 Z
Add Cess @ 1% on "Z" 449.02
Cost of 10 metre 45350.76
Cost of 1 metre 4535.08
Say 4535.10
SUB HEAD : 18- WATER SUPPLY 1494
18.6A Providing and fixing PPR Unions
18.6A.1 PPR Union 20mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8306 PPR Union 20mm each 1.00 60.00 60.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 221.05 W
Add 1 % Water charges on "W" 2.21
TOTAL 223.26 X
Add GST on "X" (multiplying
factor 0.1405) 31.37
TOTAL 254.63 Y
Add 15% CPOH on "Y" 38.19
TOTAL 292.82 Z
Add Cess @ 1% on "Z" 2.93
Cost of 1 No 295.75
Say 295.75
18.6A.2 PPR Union 25mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8307 PPR Union 25mm each 1.00 110.00 110.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 271.05 W
Add 1 % Water charges on "W" 2.71
TOTAL 273.76 X
Add GST on "X" (multiplying
factor 0.1405) 38.46
TOTAL 312.22 Y
Add 15% CPOH on "Y" 46.83
TOTAL 359.06 Z
Add Cess @ 1% on "Z" 3.59
Cost of 1 No 362.65
Say 362.65
18.6A.3 PPR Union 32mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8308 PPR Union 32mm each 1.00 150.00 150.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
SUB HEAD : 18- WATER SUPPLY 1495
Code Description Unit Quantity Rate Amount
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 311.05 W
Add 1 % Water charges on "W" 3.11
TOTAL 314.16 X
Add GST on "X" (multiplying
factor 0.1405) 44.14
TOTAL 358.30 Y
Add 15% CPOH on "Y" 53.74
TOTAL 412.04 Z
Add Cess @ 1% on "Z" 4.12
Cost of 1 No 416.16
Say 416.15
18.6A.4 PPR Union 40mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8309 PPR Union 40mm each 1.00 220.00 220.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 381.05 W
Add 1 % Water charges on "W" 3.81
TOTAL 384.86 X
Add GST on "X" (multiplying
factor 0.1405) 54.07
TOTAL 438.93 Y
Add 15% CPOH on "Y" 65.84
TOTAL 504.77 Z
Add Cess @ 1% on "Z" 5.05
Cost of 1 No 509.82
Say 509.80
18.6A.5 PPR Union 50mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8310 PPR Union 50mm each 1.00 410.00 410.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
SUB HEAD : 18- WATER SUPPLY 1496
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.11 645.00 70.95
TOTAL 571.05 W
Add 1 % Water charges on "W" 5.71
TOTAL 576.76 X
Add GST on "X" (multiplying
factor 0.1405) 81.03
TOTAL 657.79 Y
Add 15% CPOH on "Y" 98.67
TOTAL 756.46 Z
Add Cess @ 1% on "Z" 7.56
Cost of 1 No 764.03
Say 764.05
18.6A.6 PPR Union 63mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8311 PPR Union 63mm each 1.00 550.00 550.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 711.05 W
Add 1 % Water charges on "W" 7.11
TOTAL 718.16 X
Add GST on "X" (multiplying
factor 0.1405) 100.90
TOTAL 819.06 Y
Add 15% CPOH on "Y" 122.86
TOTAL 941.92 Z
Add Cess @ 1% on "Z" 9.42
Cost of 1 No 951.34
Say 951.35
18.6A.7 PPR Union 75mm
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL:
8312 PPR Union 75mm each 1.00 1100.00 1100.00
9999 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR:
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 1261.05 W
Add 1 % Water charges on "W" 12.61
TOTAL 1273.66 X
Add GST on "X" (multiplying
factor 0.1405) 178.95
TOTAL 1452.61 Y
Add 15% CPOH on "Y" 217.89
TOTAL 1670.50 Z
Add Cess @ 1% on "Z" 16.70
Cost of 1 No 1687.20
Say 1687.20
SUB HEAD : 18- WATER SUPPLY 1497
18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply, including all CPVC plain & brass
threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one step CPVC solvent cement and
testing of joints complete as per direction of Engineer in Charge.
Internal work - Exposed on wall
18.7.1 15 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8636 Chlorinated Polyvinyl - chloride (CPVC)
pipe 15 mm nominal dia. metre 10.00 49.00 490.00 P
Add 30% for fittings and wastage
etc. on (P) 147.00
30 x P / 100
9999 Cement, sand and grit etc. L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.82 714.00 585.48
0114 Beldar day 0.66 645.00 425.70
TOTAL 1912.69 W
Add 1 % Water charges on "W" 19.13
TOTAL 1931.81 X
Add GST on "X" (multiplying
factor 0.1405) 271.42
TOTAL 2203.23 Y
Add 15% CPOH on "Y" 330.49
TOTAL 2533.72 Z
Add Cess @ 1% on "Z" 25.34
Cost of 10 metre 2559.06
Cost of 1 metre 255.91
Say 255.90
18.7.2 20 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8637 Chlorinated Polyvinyl - chloride
(CPVC) pipe 20 mm nominal dia. metre 10.00 80.00 800.00 P
Add 30% for fittings and wastage
etc. on (P) 240.00
30 x P / 100
9999 Cement, sand and grit etc. L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
SUB HEAD : 18- WATER SUPPLY 1498
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 2429.93 W
Add 1 % Water charges on "W" 24.30
TOTAL 2454.23 X
Add GST on "X" (multiplying
factor 0.1405) 344.82
TOTAL 2799.05 Y
Add 15% CPOH on "Y" 419.86
TOTAL 3218.90 Z
Add Cess @ 1% on "Z" 32.19
Cost of 10 metre 3251.09
Cost of 1 metre 325.11
Say 325.10
18.7.3 25 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8638 Chlorinated Polyvinyl - chloride (CPVC)
pipe 25 mm nominal dia. metre 10.00 127.97 1279.70 P
Add 30% for fittings and wastage
etc. on (P) 383.91
30 x P / 100
9999 Cement, sand and grit etc. L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.66 645.00 425.70
TOTAL 3053.54 W
Add 1 % Water charges on "W" 30.54
TOTAL 3084.07 X
Add GST on "X" (multiplying
factor 0.1405) 433.31
TOTAL 3517.39 Y
Add 15% CPOH on "Y" 527.61
TOTAL 4044.99 Z
Add Cess @ 1% on "Z" 40.45
Cost of 10 metre 4085.44
Cost of 1 metre 408.54
Say 408.55
18.7.4 32 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8639 Chlorinated Polyvinyl - chloride
(CPVC) pipe 32 mm nominal dia. metre 10.00 165.00 1650.00 P
Add 30% for fittings and wastage
etc. on (P) 495.00
30 x P / 100
9999 Cement, sand and grit etc. L.S. 4.16 2.12 8.82
SUB HEAD : 18- WATER SUPPLY 1499
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.98 645.00 632.10
TOTAL 3744.36 W
Add 1 % Water charges on "W" 37.44
TOTAL 3781.80 X
Add GST on "X" (multiplying
factor 0.1405) 531.34
TOTAL 4313.15 Y
Add 15% CPOH on "Y" 646.97
TOTAL 4960.12 Z
Add Cess @ 1% on "Z" 49.60
Cost of 10 metre 5009.72
Cost of 1 metre 500.97
Say 500.95
18.7.5 40 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8640 Chlorinated Polyvinyl - chloride
(CPVC) pipe 40 mm nominal dia. metre 10.00 230.00 2300.00 P
Add 30% for fittings and wastage
etc. on (P) 690.00
30 x P / 100
9999 Cement, sand and grit etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 5040.31 W
Add 1 % Water charges on "W" 50.40
TOTAL 5090.71 X
Add GST on "X" (multiplying
factor 0.1405) 715.25
TOTAL 5805.96 Y
Add 15% CPOH on "Y" 870.89
TOTAL 6676.85 Z
Add Cess @ 1% on "Z" 66.77
Cost of 10 metre 6743.62
Cost of 1 metre 674.36
Say 674.35
SUB HEAD : 18- WATER SUPPLY 1500
18.7.6 50 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8641 Chlorinated Polyvinyl - chloride
(CPVC) pipe 50 mm nominal dia. metre 10.00 375.25 3752.50 P
Add 30% for fittings and wastage
etc. on (P) 1125.75
30 x P / 100
9999 Cement, sand and grit etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 6928.56 W
Add 1 % Water charges on "W" 69.29
TOTAL 6997.85 X
Add GST on "X" (multiplying
factor 0.1405) 983.20
TOTAL 7981.04 Y
Add 15% CPOH on "Y" 1197.16
TOTAL 9178.20 Z
Add Cess @ 1% on "Z" 91.78
Cost of 10 metre 9269.98
Cost of 1 metre 927.00
Say 927.00
18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply, including all CPVC plain & brass
threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes
jointing of pipes & fittings with one step CPVC solvent cement and the cost of
cutting chases and making good the same including testing of joints complete
as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.
18.8.1 15 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8636 Chlorinated Polyvinyl - chloride (CPVC)
pipe 15 mm nominal dia. metre 10.00 49.00 490.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 367.50
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 Of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1501
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 3731.16 W
Add 1 % Water charges on "W-A" 20.13
TOTAL 3751.29 X
Add GST on "X-A" (multiplying
factor 0.1405) 285.68
TOTAL 4036.97 Y
Add 15% CPOH on "Y-A" 347.85
TOTAL 4384.81 Z
Add Cess @ 1% on "Z-A" 26.67
Cost of 10 metre 4411.48
Cost of 1 metre 441.15
Say 441.15
18.8.2 20 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8637 Chlorinated Polyvinyl - chloride
(CPVC) pipe 20 mm nominal dia. metre 10.00 80.00 800.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 600.00
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 Of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4273.66 W
Add 1 % Water charges on "W-A" 25.56
TOTAL 4299.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 362.66
TOTAL 4661.88 Y
Add 15% CPOH on "Y-A" 441.58
TOTAL 5103.46 Z
Add Cess @ 1% on "Z-A" 33.85
Cost of 10 metre 5137.31
Cost of 1 metre 513.73
Say 513.75
SUB HEAD : 18- WATER SUPPLY 1502
18.8.3 25 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8638 Chlorinated Polyvinyl - chloride
(CPVC) pipe 25 mm nominal dia. metre 10.00 127.97 1279.70 P
Add 75% for fittings, clamps and
wastage etc. on (P) 959.78
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 Of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 5113.14 W
Add 1 % Water charges on "W-A" 33.95
TOTAL 5147.09 X
Add GST on "X-A" (multiplying
factor 0.1405) 481.79
TOTAL 5628.87 Y
Add 15% CPOH on "Y-A" 586.63
TOTAL 6215.50 Z
Add Cess @ 1% on "Z-A" 44.98
Cost of 10 metre 6260.48
Cost of 1 metre 626.05
Say 626.05
18.8.4 32 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8639 Chlorinated Polyvinyl - chloride
(CPVC) pipe 32 mm nominal dia. metre 10.00 165.00 1650.00 P
Add 75% for fittings, clamps and
wastage etc. on (P) 1237.50
75 x P / 100
Making chases upto 7.5 x 7.5 cm.
in walls and making good the same
18.78 Rate as per item no. 18.78 Of
SH: Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1503
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 5761.16 W
Add 1 % Water charges on "W-A" 40.43
TOTAL 5801.59 X
Add GST on "X-A" (multiplying
factor 0.1405) 573.74
TOTAL 6375.34 Y
Add 15% CPOH on "Y-A" 698.60
TOTAL 7073.94 Z
Add Cess @ 1% on "Z-A" 53.56
Cost of 10 metre 7127.50
Cost of 1 metre 712.75
Say 712.75
18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain & brass
threaded fittings This includes jointing of pipes & fittings with one step CPVC
solvent cement, trenching, refilling & testing of joints complete as per direction
of Engineer in Charge.
External work
18.9.1 15 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8636 Chlorinated Polyvinyl - chloride
(CPVC) pipe 15 mm nominal dia. metre 10.00 49.00 490.00 P
Add 30% for fittings and wastage
etc. on (P) 147.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 1654.32 W
Add 1 % Water charges on "W" 16.54
TOTAL 1670.86 X
Add GST on "X" (multiplying
factor 0.1405) 234.76
TOTAL 1905.62 Y
Add 15% CPOH on "Y" 285.84
TOTAL 2191.46 Z
Add Cess @ 1% on "Z" 21.91
Cost of 10 metre 2213.38
Cost of 1 metre 221.34
Say 221.35
SUB HEAD : 18- WATER SUPPLY 1504
18.9.2 20 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8637 Chlorinated Polyvinyl - chloride
(CPVC) pipe 20 mm nominal dia. metre 10.00 80.00 800.00 P
Add 30% for fittings and wastage
etc. on (P) 240.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2057.32 W
Add 1 % Water charges on "W" 20.57
TOTAL 2077.89 X
Add GST on "X" (multiplying
factor 0.1405) 291.94
TOTAL 2369.84 Y
Add 15% CPOH on "Y" 355.48
TOTAL 2725.31 Z
Add Cess @ 1% on "Z" 27.25
Cost of 10 metre 2752.57
Cost of 1 metre 275.26
Say 275.25
18.9.3 25 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8638 Chlorinated Polyvinyl - chloride
(CPVC) pipe 25 mm nominal dia. metre 10.00 127.97 1279.70 P
Add 30% for fittings and wastage
etc. on (P) 383.91
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2770.34 W
Add 1 % Water charges on "W" 27.70
TOTAL 2798.04 X
Add GST on "X" (multiplying
factor 0.1405) 393.13
TOTAL 3191.17 Y
Add 15% CPOH on "Y" 478.68
TOTAL 3669.84 Z
Add Cess @ 1% on "Z" 36.70
Cost of 10 metre 3706.54
Cost of 1 metre 370.65
Say 370.65
SUB HEAD : 18- WATER SUPPLY 1505
18.9.4 32 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8639 Chlorinated Polyvinyl - chloride (CPVC)
pipe 32 mm nominal dia. metre 10.00 165.00 1650.00 P
Add 30% for fittings and wastage
etc. on (P) 495.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 3251.73 W
Add 1 % Water charges on "W" 32.52
TOTAL 3284.25 X
Add GST on "X" (multiplying
factor 0.1405) 461.44
TOTAL 3745.68 Y
Add 15% CPOH on "Y" 561.85
TOTAL 4307.54 Z
Add Cess @ 1% on "Z" 43.08
Cost of 10 metre 4350.61
Cost of 1 metre 435.06
Say 435.05
18.9.5 40 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8640 Chlorinated Polyvinyl - chloride
(CPVC) pipe 40 mm nominal dia. metre 10.00 230.00 2300.00 P
Add 30% for fittings and wastage
etc. on (P) 690.00
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 4179.69 W
Add 1 % Water charges on "W" 41.80
TOTAL 4221.49 X
Add GST on "X" (multiplying
factor 0.1405) 593.12
TOTAL 4814.61 Y
Add 15% CPOH on "Y" 722.19
TOTAL 5536.80 Z
Add Cess @ 1% on "Z" 55.37
Cost of 10 metre 5592.16
Cost of 1 metre 559.22
Say 559.20
SUB HEAD : 18- WATER SUPPLY 1506
18.9.6 50 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8641 Chlorinated Polyvinyl - chloride
(CPVC) pipe 50 mm nominal dia. metre 10.00 375.25 3752.50 P
Add 30% for fittings and wastage
etc. on (P) 1125.75
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 6067.94 W
Add 1 % Water charges on "W" 60.68
TOTAL 6128.62 X
Add GST on "X" (multiplying
factor 0.1405) 861.07
TOTAL 6989.69 Y
Add 15% CPOH on "Y" 1048.45
TOTAL 8038.14 Z
Add Cess @ 1% on "Z" 80.38
Cost of 10 metre 8118.53
Cost of 1 metre 811.85
Say 811.85
18.9.7 65 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8642 Chlorinated Polyvinyl - chloride
(CPVC) pipe 65 mm nominal dia. metre 10.00 793.30 7933.00 P
Add 30% for fittings and wastage
etc. on (P) 2379.90
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 11786.00 W
Add 1 % Water charges on "W" 117.86
TOTAL 11903.86 X
Add GST on "X" (multiplying
factor 0.1405) 1672.49
TOTAL 13576.35 Y
Add 15% CPOH on "Y" 2036.45
TOTAL 15612.81 Z
Add Cess @ 1% on "Z" 156.13
Cost of 10 metre 15768.93
Cost of 1 metre 1576.89
Say 1576.90
SUB HEAD : 18- WATER SUPPLY 1507
18.9.8 80 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8643 Chlorinated Polyvinyl - chloride
(CPVC) pipe 80 mm nominal dia. metre 10.00 1031.05 10310.50 P
Add 30% for fittings and wastage
etc. on (P) 3093.15
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 14876.75 W
Add 1 % Water charges on "W" 148.77
TOTAL 15025.52 X
Add GST on "X" (multiplying
factor 0.1405) 2111.09
TOTAL 17136.60 Y
Add 15% CPOH on "Y" 2570.49
TOTAL 19707.09 Z
Add Cess @ 1% on "Z" 197.07
Cost of 10 metre 19904.16
Cost of 1 metre 1990.42
Say 1990.40
18.9.9 100 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8644 Chlorinated Polyvinyl - chloride
(CPVC) pipe 100 mm nominal dia. metre 10.00 1466.75 14667.50 P
Add 30% for fittings and wastage
etc. on (P) 4400.25
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.37 784.00 290.08
0114 Beldar day 0.97 645.00 625.65
Trenching and refilling etc.
0114 Beldar day 0.80 645.00 516.00
0115 Coolie day 0.80 645.00 516.00
TOTAL 21015.48 W
Add 1 % Water charges on "W" 210.15
TOTAL 21225.63 X
Add GST on "X" (multiplying
factor 0.1405) 2982.20
TOTAL 24207.84 Y
Add 15% CPOH on "Y" 3631.18
TOTAL 27839.01 Z
Add Cess @ 1% on "Z" 278.39
Cost of 10 metre 28117.40
Cost of 1 metre 2811.74
Say 2811.75
SUB HEAD : 18- WATER SUPPLY 1508
18.9.10 150 mm nominal dia Pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8645 Chlorinated Polyvinyl - chloride
(CPVC) pipe 150 mm nominal dia. metre 10.00 3145.15 31451.50 P
Add 30% for fittings and wastage
etc. on (P) 9435.45
30 x P / 100
LABOUR
0116 Fitter (grade 1) day 0.58 784.00 454.72
0114 Beldar day 1.54 645.00 993.30
Trenching and refilling etc.
0114 Beldar day 1.20 645.00 774.00
0115 Coolie day 1.20 645.00 774.00
TOTAL 43882.97 W
Add 1 % Water charges on "W" 438.83
TOTAL 44321.80 X
Add GST on "X" (multiplying
factor 0.1405) 6227.21
TOTAL 50549.01 Y
Add 15% CPOH on "Y" 7582.35
TOTAL 58131.36 Z
Add Cess @ 1% on "Z" 581.31
Cost of 10 metre 58712.68
Cost of 1 metre 5871.27
Say 5871.25
18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting
and making good the walls etc.
Internal work - Exposed on wall
18.10.1 15 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1545 G.I. pipes 15 mm dia metre 11.50 95.00 1092.50
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 12.30 = 14.145
kg = 0.014145 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.014145 145.72 2.06
9999 White lead, hemp, oil etc. L.S. 8.06 2.12 17.09
9999 Cement, sand and grit etc. L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1509
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 2273.10 W
Add 1 % Water charges on "W" 22.73
TOTAL 2295.83 X
Add GST on "X" (multiplying
factor 0.1405) 322.56
TOTAL 2618.39 Y
Add 15% CPOH on "Y" 392.76
TOTAL 3011.15 Z
Add Cess @ 1% on "Z" 30.11
Cost of 10 metre 3041.26
Cost of 1 metre 304.13
Say 304.15
18.10.2 20 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1546 G.I. pipes 20 mm dia metre 11.50 130.00 1495.00
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 15.90= 18.285
kg = 0.018285 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.018285 145.72 2.66
9999 White lead, hemp, oil etc. L.S. 8.06 2.12 17.09
9999 Cement, sand and grit etc. L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.82 714.00 585.48
0114 Beldar day 0.66 645.00 425.70
TOTAL 2790.44 W
Add 1 % Water charges on "W" 27.90
TOTAL 2818.34 X
Add GST on "X" (multiplying
factor 0.1405) 395.98
TOTAL 3214.32 Y
Add 15% CPOH on "Y" 482.15
TOTAL 3696.47 Z
Add Cess @ 1% on "Z" 36.96
Cost of 10 metre 3733.43
Cost of 1 metre 373.34
Say 373.35
18.10.3 25 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1547 G.I. pipes 25 mm dia metre 11.50 196.00 2254.00
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 24.60 = 28.29
kg = 0.02829 tonne
SUB HEAD : 18- WATER SUPPLY 1510
Code Description Unit Quantity Rate Amount
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.02829 145.72 4.12
9999 White lead, hemp, oil etc. L.S. 9.49 2.12 20.12
9999 Cement, sand and grit etc. L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.66 645.00 425.70
TOTAL 3671.20 W
Add 1 % Water charges on "W" 36.71
TOTAL 3707.91 X
Add GST on "X" (multiplying
factor 0.1405) 520.96
TOTAL 4228.87 Y
Add 15% CPOH on "Y" 634.33
TOTAL 4863.21 Z
Add Cess @ 1% on "Z" 48.63
Cost of 10 metre 4911.84
Cost of 1 metre 491.18
Say 491.20
18.10.4 32 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1548 G.I. pipes 32 mm dia metre 11.50 225.00 2587.50
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 31.70 = 36.455
kg = 0.036455 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.036455 145.72 5.31
9999 White lead, hemp, oil etc. L.S. 9.49 2.12 20.12
9999 Cement, sand and grit etc. L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.98 714.00 699.72
0114 Beldar day 0.98 645.00 632.10
TOTAL 4212.29 W
Add 1 % Water charges on "W" 42.12
TOTAL 4254.41 X
Add GST on "X" (multiplying
factor 0.1405) 597.75
TOTAL 4852.16 Y
Add 15% CPOH on "Y" 727.82
TOTAL 5579.98 Z
Add Cess @ 1% on "Z" 55.80
Cost of 10 metre 5635.78
Cost of 1 metre 563.58
Say 563.60
SUB HEAD : 18- WATER SUPPLY 1511
18.10.5 40 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1549 G.I. pipes 40 mm dia metre 11.50 290.00 3335.00
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 36.50 = 41.975
kg = 0.041975 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.041975 145.72 6.12
9999 White lead, hemp, oil etc. L.S. 13.52 2.12 28.66
9999 Cement, sand and grit etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.31 714.00 935.34
0114 Beldar day 1.31 645.00 844.95
TOTAL 5420.09 W
Add 1 % Water charges on "W" 54.20
TOTAL 5474.29 X
Add GST on "X" (multiplying
factor 0.1405) 769.14
TOTAL 6243.43 Y
Add 15% CPOH on "Y" 936.51
TOTAL 7179.94 Z
Add Cess @ 1% on "Z" 71.80
Cost of 10 metre 7251.74
Cost of 1 metre 725.17
Say 725.15
18.10.6 50 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1550 G.I. pipes 50 mm dia metre 11.50 360.00 4140.00
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 51.70 = 59.455
kg = 0.059455 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.059455 145.72 8.66
9999 White lead, hemp, oil etc. L.S. 13.52 2.12 28.66
9999 Cement, sand and grit etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 1.64 714.00 1170.96
0114 Beldar day 1.64 645.00 1057.80
TOTAL 6676.11 W
Add 1 % Water charges on "W" 66.76
TOTAL 6742.87 X
Add GST on "X" (multiplying
factor 0.1405) 947.37
TOTAL 7690.24 Y
Add 15% CPOH on "Y" 1153.54
TOTAL 8843.78 Z
Add Cess @ 1% on "Z" 88.44
Cost of 10 metre 8932.21
Cost of 1 metre 893.22
Say 893.20
SUB HEAD : 18- WATER SUPPLY 1512
18.11 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making
good the walls etc. concealed pipe, including painting with anti corrosive
bitumastic paint, cutting chases and making good the wall :
18.11.1 15 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1545 G.I. pipes 15 mm dia metre 11.50 95.00 1092.50
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 12.30 = 14.145
kg = 0.014145 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.014145 145.72 2.06
9999 White lead, hemp, oil etc. L.S. 8.06 2.12 17.09
Painting G.I. pipe with anti-corrosive
bitumastic paint two or more coats
18.40.1 (Rate same as per item no. 18.40.1) metre 10.00 10.05 100.50 A
Making chases upto 7.5x7.5cm in walls
and making good the same
18.78 Rate as per item no. 18.78 Of
SH Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4085.81 W
Add 1 % Water charges on "W-A" 22.67
TOTAL 4108.48 X
Add GST on "X-A" (multiplying
factor 0.1405) 321.74
TOTAL 4430.22 Y
Add 15% CPOH on "Y-A" 391.76
TOTAL 4821.98 Z
Add Cess @ 1% on "Z-A" 30.03
Cost of 10 metre 4852.02
Cost of 1 metre 485.20
Say 485.20
18.11.2 20 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1546 G.I. pipes 20 mm dia metre 11.50 130.00 1495.00
Weight for carriage = pipe weight +
15% for fiitings = 1.15 * 15.90= 18.285
kg = 0.018285 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.018285 145.72 2.66
9999 White lead, hemp, oil etc. L.S. 8.06 2.12 17.09
Painting G.I. pipe with anti-corrosive
bitumastic paint two or more coats
18.40.2 (Rate same as per item no. 18.40.2 Of
SH Water Supply) metre 10.00 12.00 120.00 A
Making chases upto 7.5x7.5cm in walls
and making good the same
SUB HEAD : 18- WATER SUPPLY 1513
Code Description Unit Quantity Rate Amount
18.78 Rate as per item no. 18.78 Of
SH Water Supply metre 10.00 171.80 1718.00 A
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4508.41 W
Add 1 % Water charges on "W-A" 26.70
TOTAL 4535.12 X
Add GST on "X-A" (multiplying
factor 0.1405) 378.94
TOTAL 4914.06 Y
Add 15% CPOH on "Y-A" 461.41
TOTAL 5375.47 Z
Add Cess @ 1% on "Z-A" 35.37
Cost of 10 metre 5410.84
Cost of 1 metre 541.08
Say 541.10
18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching
and refilling etc.
External work
18.12.1 15 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1545 G.I. pipes 15 mm dia metre 10.20 95.00 969.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 12.30 = 12.546 kg =
0.012546 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.012546 145.72 1.83
9999 White lead, hemp, oil etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 1999.45 W
Add 1 % Water charges on "W" 19.99
TOTAL 2019.44 X
Add GST on "X" (multiplying
factor 0.1405) 283.73
TOTAL 2303.17 Y
Add 15% CPOH on "Y" 345.48
TOTAL 2648.65 Z
Add Cess @ 1% on "Z" 26.49
Cost of 10 metre 2675.14
Cost of 1 metre 267.51
Say 267.50
SUB HEAD : 18- WATER SUPPLY 1514
18.12.2 20 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Detailsof cost for 10 metre
MATERIAL
1546 G.I. pipes 20 mm dia metre 10.20 130.00 1326.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 15.90 = 16.218 kg =
0.016218 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.016218 145.72 2.36
9999 White lead, hemp, oil etc. L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.16 645.00 103.20
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 2356.98 W
Add 1 % Water charges on "W" 23.57
TOTAL 2380.55 X
Add GST on "X" (multiplying
factor 0.1405) 334.47
TOTAL 2715.02 Y
Add 15% CPOH on "Y" 407.25
TOTAL 3122.27 Z
Add Cess @ 1% on "Z" 31.22
Cost of 10 metre 3153.50
Cost of 1 metre 315.35
Say 315.35
18.12.3 25 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1547 G.I. pipes 25 mm dia metre 10.20 196.00 1999.20
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 24.60 = 25.092 kg =
0.025092 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.025092 145.72 3.66
9999 White lead, hemp, oil etc. L.S. 6.76 2.12 14.33
LABOUR
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
SUB HEAD : 18- WATER SUPPLY 1515
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.66 645.00 425.70
TOTAL 3123.92 W
Add 1 % Water charges on "W" 31.24
TOTAL 3155.16 X
Add GST on "X" (multiplying
factor 0.1405) 443.30
TOTAL 3598.46 Y
Add 15% CPOH on "Y" 539.77
TOTAL 4138.22 Z
Add Cess @ 1% on "Z" 41.38
Cost of 10 metre 4179.61
Cost of 1 metre 417.96
Say 417.95
18.12.4 32 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1548 G.I. pipes 32 mm dia metre 10.20 225.00 2295.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 31.70 = 32.334 kg =
0.032334 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.032334 145.72 4.71
9999 White lead, hemp, oil etc. L.S. 6.76 2.12 14.33
LABOUR
0116 Fitter (grade 1) day 0.12 784.00 94.08
0114 Beldar day 0.25 645.00 161.25
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 3420.77 W
Add 1 % Water charges on "W" 34.21
TOTAL 3454.98 X
Add GST on "X" (multiplying
factor 0.1405) 485.42
TOTAL 3940.41 Y
Add 15% CPOH on "Y" 591.06
TOTAL 4531.47 Z
Add Cess @ 1% on "Z" 45.31
Cost of 10 metre 4576.78
Cost of 1 metre 457.68
Say 457.70
SUB HEAD : 18- WATER SUPPLY 1516
18.12.5 40 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1549 G.I. pipes 40 mm dia metre 10.20 290.00 2958.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 36.50 = 37.23 kg =
0.03723 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.03723 145.72 5.43
9999 White lead, hemp, oil etc. L.S. 9.49 2.12 20.12
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 4173.23 W
Add 1 % Water charges on "W" 41.73
TOTAL 4214.97 X
Add GST on "X" (multiplying
factor 0.1405) 592.20
TOTAL 4807.17 Y
Add 15% CPOH on "Y" 721.08
TOTAL 5528.24 Z
Add Cess @ 1% on "Z" 55.28
Cost of 10 metre 5583.53
Cost of 1 metre 558.35
Say 558.35
18.12.6 50 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1550 G.I. pipes 50 mm dia metre 10.20 360.00 3672.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 51.70 = 52.73 kg =
0.05273 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.052734 145.72 7.68
9999 White lead, hemp, oil etc. L.S. 9.49 2.12 20.12
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.33 645.00 212.85
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
SUB HEAD : 18- WATER SUPPLY 1517
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.66 645.00 425.70
TOTAL 4889.49 W
Add 1 % Water charges on "W" 48.89
TOTAL 4938.39 X
Add GST on "X" (multiplying
factor 0.1405) 693.84
TOTAL 5632.23 Y
Add 15% CPOH on "Y" 844.83
TOTAL 6477.07 Z
Add Cess @ 1% on "Z" 64.77
Cost of 10 metre 6541.84
Cost of 1 metre 654.18
Say 654.20
18.12.7 65 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1551 G.I. pipes 65 mm dia metre 10.20 415.00 4233.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 66.30 = 67.626 kg =
0.067626 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.067626 145.72 9.85
9999 White lead, hemp, oil etc. L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 5744.62 W
Add 1 % Water charges on "W" 57.45
TOTAL 5802.06 X
Add GST on "X" (multiplying
factor 0.1405) 815.19
TOTAL 6617.25 Y
Add 15% CPOH on "Y" 992.59
TOTAL 7609.84 Z
Add Cess @ 1% on "Z" 76.10
Cost of 10 metre 7685.94
Cost of 1 metre 768.59
Say 768.60
SUB HEAD : 18- WATER SUPPLY 1518
18.12.8 80 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1552 G.I. pipes 80 mm dia metre 10.20 525.00 5355.00
Weight for carriage = pipe weight + 2%
for fiitings = 1.02 * 86.40 = 88.128 kg =
0.088128 tonne
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.088128 145.72 12.84
9999 White lead, hemp, oil etc. L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.66 645.00 425.70
Trenching and refilling etc.
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.66 645.00 425.70
TOTAL 6869.60 W
Add 1 % Water charges on "W" 68.70
TOTAL 6938.30 X
Add GST on "X" (multiplying
factor 0.1405) 974.83
TOTAL 7913.13 Y
Add 15% CPOH on "Y" 1186.97
TOTAL 9100.10 Z
Add Cess @ 1% on "Z" 91.00
Cost of 10 metre 9191.10
Cost of 1 metre 919.11
Say 919.10
18.13 Making connection of G.I. distribution branch with G.I. main of following sizes
by providing and fixing tee, including cutting and threading the pipe etc.
complete :
18.13.1 25 to 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one connection.
Take 25mm dia as an average size.
MATERIAL
1608 G.I. tees (equal) 25 mm each 1.00 65.00 65.00
1555 G.I. back (jam) nuts 25 mm dia each 1.00 18.00 18.00
9988 Carriage of materials and sundries L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 565.87 W
Add 1 % Water charges on "W" 5.66
TOTAL 571.53 X
Add GST on "X" (multiplying
factor 0.1405) 80.30
TOTAL 651.83 Y
Add 15% CPOH on "Y" 97.77
TOTAL 749.60 Z
Add Cess @ 1% on "Z" 7.50
Cost of one connection 757.10
Say 757.10
SUB HEAD : 18- WATER SUPPLY 1519
18.13.2 50 to 80 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one connection.
Take 65mm dia as an average size.
MATERIAL
1612 G.I. tees (equal) 65 mm each 1.00 452.00 452.00
1559 G.I. back (jam) nuts 65 mm dia each 1.00 25.00 25.00
9988 Carriage of materials and sundries L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.45 784.00 352.80
0114 Beldar day 0.45 645.00 290.25
TOTAL 1131.35 W
Add 1 % Water charges on "W" 11.31
TOTAL 1142.66 X
Add GST on "X" (multiplying
factor 0.1405) 160.54
TOTAL 1303.21 Y
Add 15% CPOH on "Y" 195.48
TOTAL 1498.69 Z
Add Cess @ 1% on "Z" 14.99
Cost of one connection 1513.68
Say 1513.70
18.14 Fixing water meter and stop cock in G.I. pipe line including cutting and
threading the pipe and making long screws etc. complete (cost of water meter
and stop cock to be paid separately).
Code Description Unit Quantity Rate Amount
Details of cost for one meter with
stop cock
MATERIAL
1555 G.I. back (jam) nuts 25 mm dia each 1.00 18.00 18.00
9988 Carriage of materials and sundries L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 500.87 W
Add 1 % Water charges on "W" 5.01
TOTAL 505.88 X
Add GST on "X" (multiplying
factor 0.1405) 71.08
TOTAL 576.95 Y
Add 15% CPOH on "Y" 86.54
TOTAL 663.50 Z
Add Cess @ 1% on "Z" 6.63
Cost of one metre with stop cock 670.13
Say 670.15
SUB HEAD : 18- WATER SUPPLY 1520
18.15 Providing and fixing brass bib cock of approved quality :
18.15.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1339 Brass bib-cock 15 mm dia each 1.00 210.00 210.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 227.09 W
Add 1 % Water charges on "W" 2.27
TOTAL 229.36 X
Add GST on "X" (multiplying
factor 0.1405) 32.22
TOTAL 261.58 Y
Add 15% CPOH on "Y" 39.24
TOTAL 300.82 Z
Add Cess @ 1% on "Z" 3.01
Cost of one no. 303.83
Say 303.85
18.15.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1340 Brass bib-cock 20 mm dia each 1.00 225.00 225.00
9988 Carriage of materials and fixing charges L.S. 9.49 2.12 20.12
TOTAL 245.12 W
Add 1 % Water charges on "W" 2.45
TOTAL 247.57 X
Add GST on "X" (multiplying
factor 0.1405) 34.78
TOTAL 282.35 Y
Add 15% CPOH on "Y" 42.35
TOTAL 324.71 Z
Add Cess @ 1% on "Z" 3.25
Cost of one no. 327.95
Say 327.95
18.16 Providing and fixing brass stop cock of approved quality :
18.16.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1342 Brass stop-cock 15 mm dia each 1.00 210.00 210.00
SUB HEAD : 18- WATER SUPPLY 1521
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 227.09 W
Add 1 % Water charges on "W" 2.27
TOTAL 229.36 X
Add GST on "X" (multiplying
factor 0.1405) 32.22
TOTAL 261.58 Y
Add 15% CPOH on "Y" 39.24
TOTAL 300.82 Z
Add Cess @ 1% on "Z" 3.01
Cost of one no. 303.83
Say 303.85
18.16.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1343 Brass stop-cock 20 mm dia each 1.00 225.00 225.00
9988 Carriage of materials and fixing charges L.S. 9.49 2.12 20.12
TOTAL 245.12 W
Add 1 % Water charges on "W" 2.45
TOTAL 247.57 X
Add GST on "X" (multiplying
factor 0.1405) 34.78
TOTAL 282.35 Y
Add 15% CPOH on "Y" 42.35
TOTAL 324.71 Z
Add Cess @ 1% on "Z" 3.25
Cost of one no. 327.95
Say 327.95
18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality
(screwed end) :
18.17.1 25 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1927 Brass full way valve with C.I. wheel
(screwed end) 25 mm dia each 1.00 375.00 375.00
9988 Carriage of materials and fixing charges L.S. 10.79 2.12 22.87
TOTAL 397.87 W
Add 1 % Water charges on "W" 3.98
TOTAL 401.85 X
Add GST on "X" (multiplying
factor 0.1405) 56.46
TOTAL 458.31 Y
Add 15% CPOH on "Y" 68.75
TOTAL 527.06 Z
Add Cess @ 1% on "Z" 5.27
Cost of one no. 532.33
Say 532.35
SUB HEAD : 18- WATER SUPPLY 1522
18.17.1A 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for 1 No.
MATERIAL
1926 20 mm dia Gunmetal gate valve
with wheel each 1.00 325.00 325.00
9977 Carriage of metrial and fixing charge L.S. 9.49 2.12 20.12
TOTAL 345.12 W
Add 1 % Water charges on "W" 3.45
TOTAL 348.57 X
Add GST on "X" (multiplying
factor 0.1405) 48.97
TOTAL 397.54 Y
Add 15% CPOH on "Y" 59.63
TOTAL 457.18 Z
Add Cess @ 1% on "Z" 4.57
Cost of 1 No. 461.75
Say 461.75
18.17.2 32 mm nominal bore.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1928 Brass full way valve with C.I. wheel
(screwed end) 32 mm dia each 1.00 415.00 415.00
9988 Carriage of materials and fixing charges L.S. 12.22 2.12 25.91
TOTAL 440.91 W
Add 1 % Water charges on "W" 4.41
TOTAL 445.32 X
Add GST on "X" (multiplying
factor 0.1405) 62.57
TOTAL 507.88 Y
Add 15% CPOH on "Y" 76.18
TOTAL 584.06 Z
Add Cess @ 1% on "Z" 5.84
Cost of one no. 589.91
Say 589.90
18.17.3 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1929 Brass full way valve with C.I. wheel
(screwed end) 40 mm dia each 1.00 500.00 500.00
SUB HEAD : 18- WATER SUPPLY 1523
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 528.66 W
Add 1 % Water charges on "W" 5.29
TOTAL 533.95 X
Add GST on "X" (multiplying
factor 0.1405) 75.02
TOTAL 608.97 Y
Add 15% CPOH on "Y" 91.35
TOTAL 700.31 Z
Add Cess @ 1% on "Z" 7.00
Cost of one no. 707.32
Say 707.30
18.17.4 50 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1930 Brass full way valve with C.I. wheel
(screwed end) 50 mm dia each 1.00 625.00 625.00
9988 Carriage of materials and fixing charges L.S. 14.82 2.12 31.42
TOTAL 656.42 W
Add 1 % Water charges on "W" 6.56
TOTAL 662.98 X
Add GST on "X" (multiplying
factor 0.1405) 93.15
TOTAL 756.13 Y
Add 15% CPOH on "Y" 113.42
TOTAL 869.55 Z
Add Cess @ 1% on "Z" 8.70
Cost of one no. 878.25
Say 878.25
18.17.5 65 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1931 Brass full way valve with C.I.
wheel (screwed end) 65 mm dia each 1.00 1080.00 1080.00
9988 Carriage of materials and fixing charges L.S. 16.12 2.12 34.17
TOTAL 1114.17 W
Add 1 % Water charges on "W" 11.14
TOTAL 1125.32 X
Add GST on "X" (multiplying
factor 0.1405) 158.11
TOTAL 1283.42 Y
Add 15% CPOH on "Y" 192.51
TOTAL 1475.94 Z
Add Cess @ 1% on "Z" 14.76
Cost of one no. 1490.70
Say 1490.70
SUB HEAD : 18- WATER SUPPLY 1524
18.17.6 80 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1932 Brass full way valve with C.I. wheel
(screwed end) 80 mm dia each 1.00 1625.00 1625.00
9988 Carriage of materials and fixing charges L.S. 18.85 2.12 39.96
TOTAL 1664.96 W
Add 1 % Water charges on "W" 16.65
TOTAL 1681.61 X
Add GST on "X" (multiplying
factor 0.1405) 236.27
TOTAL 1917.88 Y
Add 15% CPOH on "Y" 287.68
TOTAL 2205.56 Z
Add Cess @ 1% on "Z" 22.06
Cost of one no. 2227.62
Say 2227.60
18.18 Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete :
18.18.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1922 H.P. or L.P. ball valve with polythene
floats: 15 mm dia each 1.00 215.00 215.00
9988 Carriage of materials and fixing charges L.S. 21.58 2.12 45.75
TOTAL 260.75 W
Add 1 % Water charges on "W" 2.61
TOTAL 263.36 X
Add GST on "X" (multiplying
factor 0.1405) 37.00
TOTAL 300.36 Y
Add 15% CPOH on "Y" 45.05
TOTAL 345.41 Z
Add Cess @ 1% on "Z" 3.45
Cost of one no. 348.87
Say 348.85
18.18.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1923 H.P. or L.P. ball valve with polythene
floats: 20 mm dia each 1.00 240.00 240.00
SUB HEAD : 18- WATER SUPPLY 1525
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 26.91 2.12 57.05
TOTAL 297.05 W
Add 1 % Water charges on "W" 2.97
TOTAL 300.02 X
Add GST on "X" (multiplying
factor 0.1405) 42.15
TOTAL 342.17 Y
Add 15% CPOH on "Y" 51.33
TOTAL 393.50 Z
Add Cess @ 1% on "Z" 3.93
Cost of one no. 397.43
Say 397.45
18.18.3 25 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1924 H.P. or L.P. ball valve with polythene
floats: 25 mm dia each 1.00 230.00 230.00
9988 Carriage of materials and fixing charges L.S. 32.24 2.12 68.35
TOTAL 298.35 W
Add 1 % Water charges on "W" 2.98
TOTAL 301.33 X
Add GST on "X" (multiplying
factor 0.1405) 42.34
TOTAL 343.67 Y
Add 15% CPOH on "Y" 51.55
TOTAL 395.22 Z
Add Cess @ 1% on "Z" 3.95
Cost of one no. 399.17
Say 399.15
18.19 Providing and fixing gun metal non- return valve of approved quality (screwed
end) :
18.19.1 25 mm nominal bore
18.19.1.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1933 Gunmetal non-return valve-horizontal
(screwed end) 25 mm dia each 1.00 350.00 350.00
SUB HEAD : 18- WATER SUPPLY 1526
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 378.66 W
Add 1 % Water charges on "W" 3.79
TOTAL 382.45 X
Add GST on "X" (multiplying
factor 0.1405) 53.73
TOTAL 436.18 Y
Add 15% CPOH on "Y" 65.43
TOTAL 501.61 Z
Add Cess @ 1% on "Z" 5.02
Cost of one no. 506.63
Say 506.65
18.19.1.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3080 Gunmetal non-return valve-vertical
(screwed end) 25 mm dia each 1.00 400.00 400.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 428.66 W
Add 1 % Water charges on "W" 4.29
TOTAL 432.95 X
Add GST on "X" (multiplying
factor 0.1405) 60.83
TOTAL 493.78 Y
Add 15% CPOH on "Y" 74.07
TOTAL 567.85 Z
Add Cess @ 1% on "Z" 5.68
Cost of one no. 573.52
Say 573.50
18.19.2 32 mm nominal bore
18.19.2.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1934 Gunmetal non-return valve-horizontal
(screwed end) 32 mm dia each 1.00 475.00 475.00
9988 Carriage of materials and fixing charges L.S. 14.82 2.12 31.42
TOTAL 506.42 W
Add 1 % Water charges on "W" 5.06
TOTAL 511.48 X
Add GST on "X" (multiplying
factor 0.1405) 71.86
TOTAL 583.35 Y
Add 15% CPOH on "Y" 87.50
TOTAL 670.85 Z
Add Cess @ 1% on "Z" 6.71
Cost of one no. 677.56
Say 677.55
SUB HEAD : 18- WATER SUPPLY 1527
18.19.2.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3084 Gunmetal non-return valve-vertical
(screwed end) 32 mm dia each 1.00 550.00 550.00
9988 Carriage of materials and fixing charges L.S. 14.82 2.12 31.42
TOTAL 581.42 W
Add 1 % Water charges on "W" 5.81
TOTAL 587.23 X
Add GST on "X" (multiplying
factor 0.1405) 82.51
TOTAL 669.74 Y
Add 15% CPOH on "Y" 100.46
TOTAL 770.20 Z
Add Cess @ 1% on "Z" 7.70
Cost of one no. 777.90
Say 777.90
18.19.3 40 mm nominal bore
18.19.3.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1935 Gunmetal non-return valve-horizontal
(screwed end) 40 mm dia each 1.00 575.00 575.00
9988 Carriage of materials and fixing charges L.S. 16.12 2.12 34.17
TOTAL 609.17 W
Add 1 % Water charges on "W" 6.09
TOTAL 615.27 X
Add GST on "X" (multiplying
factor 0.1405) 86.44
TOTAL 701.71 Y
Add 15% CPOH on "Y" 105.26
TOTAL 806.97 Z
Add Cess @ 1% on "Z" 8.07
Cost of one no. 815.04
Say 815.05
18.19.3.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3088 Gunmetal non-return valve-vertical
(screwed end) 40 mm dia each 1.00 750.00 750.00
SUB HEAD : 18- WATER SUPPLY 1528
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 16.12 2.12 34.17
TOTAL 784.17 W
Add 1 % Water charges on "W" 7.84
TOTAL 792.02 X
Add GST on "X" (multiplying
factor 0.1405) 111.28
TOTAL 903.29 Y
Add 15% CPOH on "Y" 135.49
TOTAL 1038.79 Z
Add Cess @ 1% on "Z" 10.39
Cost of one no. 1049.18
Say 1049.20
18.19.4 50 mm nominal bore
18.19.4.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1936 Gunmetal non-return valve-horizontal
(screwed end) 50 mm dia each 1.00 840.00 840.00
9988 Carriage of materials and fixing charges L.S. 17.55 2.12 37.21
TOTAL 877.21 W
Add 1 % Water charges on "W" 8.77
TOTAL 885.98 X
Add GST on "X" (multiplying
factor 0.1405) 124.48
TOTAL 1010.46 Y
Add 15% CPOH on "Y" 151.57
TOTAL 1162.03 Z
Add Cess @ 1% on "Z" 11.62
Cost of one no. 1173.65
Say 1173.65
18.19.4.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3092 Gunmetal non-return valve-vertical
(screwed end) 50 mm dia each 1.00 950.00 950.00
9988 Carriage of materials and fixing charges L.S. 17.55 2.12 37.21
TOTAL 987.21 W
Add 1 % Water charges on "W" 9.87
TOTAL 997.08 X
Add GST on "X" (multiplying
factor 0.1405) 140.09
TOTAL 1137.17 Y
Add 15% CPOH on "Y" 170.58
TOTAL 1307.74 Z
Add Cess @ 1% on "Z" 13.08
Cost of one no. 1320.82
Say 1320.80
SUB HEAD : 18- WATER SUPPLY 1529
18.19.5 65 mm nominal bore
18.19.5.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1937 Gunmetal non-return valve-horizontal
(screwed end) 65 mm dia each 1.00 1525.00 1525.00
9988 Carriage of materials and fixing charges L.S. 18.85 2.12 39.96
TOTAL 1564.96 W
Add 1 % Water charges on "W" 15.65
TOTAL 1580.61 X
Add GST on "X" (multiplying
factor 0.1405) 222.08
TOTAL 1802.69 Y
Add 15% CPOH on "Y" 270.40
TOTAL 2073.09 Z
Add Cess @ 1% on "Z" 20.73
Cost of one no. 2093.82
Say 2093.80
18.19.5.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3096 Gunmetal non-return valve-vertical
(screwed end) 65 mm dia each 1.00 1550.00 1550.00
9988 Carriage of materials and fixing charges L.S. 18.85 2.12 39.96
TOTAL 1589.96 W
Add 1 % Water charges on "W" 15.90
TOTAL 1605.86 X
Add GST on "X" (multiplying
factor 0.1405) 225.62
TOTAL 1831.49 Y
Add 15% CPOH on "Y" 274.72
TOTAL 2106.21 Z
Add Cess @ 1% on "Z" 21.06
Cost of one no. 2127.27
Say 2127.25
18.19.6 80 mm nominal bore
18.19.6.1 Horizontal
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1938 Gunmetal non-return valve-horizontal
(screwed end) 80 mm dia each 1.00 2300.00 2300.00
SUB HEAD : 18- WATER SUPPLY 1530
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 2342.99 W
Add 1 % Water charges on "W" 23.43
TOTAL 2366.42 X
Add GST on "X" (multiplying
factor 0.1405) 332.48
TOTAL 2698.91 Y
Add 15% CPOH on "Y" 404.84
TOTAL 3103.74 Z
Add Cess @ 1% on "Z" 31.04
Cost of one no. 3134.78
Say 3134.80
18.19.6.2 Vertical
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3300 Gunmetal non-return valve-vertical
(screwed end) 80 mm dia each 1.00 2600.00 2600.00
9988 Carriage of materials and fixing charges L.S. 20.28 2.12 42.99
TOTAL 2642.99 W
Add 1 % Water charges on "W" 26.43
TOTAL 2669.42 X
Add GST on "X" (multiplying
factor 0.1405) 375.05
TOTAL 3044.48 Y
Add 15% CPOH on "Y" 456.67
TOTAL 3501.15 Z
Add Cess @ 1% on "Z" 35.01
Cost of one no. 3536.16
Say 3536.15
18.20 Providing and fixing brass ferrule with C.I. mouth cover including boring and
tapping the main :
18.20.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1360 C.I.mouth, brass ferrule 15 mm dia each 1.00 140.00 140.00
9988 Carriage of materials and fixing charges L.S. 40.30 2.12 85.44
TOTAL 225.44 W
Add 1 % Water charges on "W" 2.25
TOTAL 227.69 X
Add GST on "X" (multiplying
factor 0.1405) 31.99
TOTAL 259.68 Y
Add 15% CPOH on "Y" 38.95
TOTAL 298.63 Z
Add Cess @ 1% on "Z" 2.99
Cost of one no. 301.62
Say 301.60
SUB HEAD : 18- WATER SUPPLY 1531
18.20.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1361 C.I.mouth, brass ferrule 20 mm dia each 1.00 160.00 160.00
9988 Carriage of materials and fixing charges L.S. 47.19 2.12 100.04
TOTAL 260.04 W
Add 1 % Water charges on "W" 2.60
TOTAL 262.64 X
Add GST on "X" (multiplying
factor 0.1405) 36.90
TOTAL 299.54 Y
Add 15% CPOH on "Y" 44.93
TOTAL 344.48 Z
Add Cess @ 1% on "Z" 3.44
Cost of one no. 347.92
Say 347.90
18.20.3 25 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1362 C.I.mouth, brass ferrule 25 mm dia each 1.00 220.00 220.00
9988 Carriage of materials and fixing charges L.S. 53.82 2.12 114.10
TOTAL 334.10 W
Add 1 % Water charges on "W" 3.34
TOTAL 337.44 X
Add GST on "X" (multiplying
factor 0.1405) 47.41
TOTAL 384.85 Y
Add 15% CPOH on "Y" 57.73
TOTAL 442.58 Z
Add Cess @ 1% on "Z" 4.43
Cost of one no. 447.00
Say 447.00
18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :
18.21.1 30 cm length
18.21.1.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1687 Unplasticised P.V.C.connection pipe
with brass union 30 cm long 15 mm
bore each 1.00 30.00 30.00
SUB HEAD : 18- WATER SUPPLY 1532
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 12.22 2.12 25.91
TOTAL 55.91 W
Add 1 % Water charges on "W" 0.56
TOTAL 56.47 X
Add GST on "X" (multiplying
factor 0.1405) 7.93
TOTAL 64.40 Y
Add 15% CPOH on "Y" 9.66
TOTAL 74.06 Z
Add Cess @ 1% on "Z" 0.74
Cost of one no. 74.80
Say 74.80
18.21.1.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1688 Unplasticised P.V.C.connection pipe
with brass union 30 cm long 20 mm
bore each 1.00 35.00 35.00
9988 Carriage of materials and fixing charges L.S. 12.22 2.12 25.91
TOTAL 60.91 W
Add 1 % Water charges on "W" 0.61
TOTAL 61.52 X
Add GST on "X" (multiplying
factor 0.1405) 8.64
TOTAL 70.16 Y
Add 15% CPOH on "Y" 10.52
TOTAL 80.68 Z
Add Cess @ 1% on "Z" 0.81
Cost of one no. 81.49
Say 81.50
18.21.2 45 cm length
18.21.2.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1689 Unplasticised P.V.C.connection pipe
with brass union 45 cm long 15 mm
bore each 1.00 35.00 35.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 63.66 W
Add 1 % Water charges on "W" 0.64
TOTAL 64.30 X
Add GST on "X" (multiplying
factor 0.1405) 9.03
TOTAL 73.33 Y
Add 15% CPOH on "Y" 11.00
TOTAL 84.33 Z
Add Cess @ 1% on "Z" 0.84
Cost of one no. 85.18
Say 85.20
SUB HEAD : 18- WATER SUPPLY 1533
18.21.2.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1690 Unplasticised P.V.C.connection pipe
with brass union 45 cm long 20 mm
bore each 1.00 48.00 48.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 76.66 W
Add 1 % Water charges on "W" 0.77
TOTAL 77.43 X
Add GST on "X" (multiplying
factor 0.1405) 10.88
TOTAL 88.31 Y
Add 15% CPOH on "Y" 13.25
TOTAL 101.55 Z
Add Cess @ 1% on "Z" 1.02
Cost of one no. 102.57
Say 102.55
18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
18.22.1 100 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1878 Shower rose C.P.brass for 15 to
20 mm inlet 100 mm dia each 1.00 110.00 110.00
9988 Carriage of materials and fixing charges L.S. 6.76 2.12 14.33
TOTAL 124.33 W
Add 1 % Water charges on "W" 1.24
TOTAL 125.57 X
Add GST on "X" (multiplying
factor 0.1405) 17.64
TOTAL 143.22 Y
Add 15% CPOH on "Y" 21.48
TOTAL 164.70 Z
Add Cess @ 1% on "Z" 1.65
Cost of one no. 166.35
Say 166.35
18.22.2 150 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1879 Shower rose C.P.brass for 15 to
20 mm inlet 150 mm dia each 1.00 125.00 125.00
SUB HEAD : 18- WATER SUPPLY 1534
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 142.09 W
Add 1 % Water charges on "W" 1.42
TOTAL 143.51 X
Add GST on "X" (multiplying
factor 0.1405) 20.16
TOTAL 163.67 Y
Add 15% CPOH on "Y" 24.55
TOTAL 188.22 Z
Add Cess @ 1% on "Z" 1.88
Cost of one no. 190.10
Say 190.10
18.23 Laying in position centrifugally cast (spun) iron S&S or flanged pipes
(excluding cost of pipe).
Code Description Unit Quantity Rate Amount
Details of cost for 5.14 quintal
10 m of 200 mm dia C.I. pipe class 'A'
Weight = (2x257) = 514kg = 5.14 quintal
LABOUR for laying pipe
0116 Fitter (grade 1) day 0.17 784.00 133.28
0117 Assistant Fitter or 2nd class Fitter day 0.17 714.00 121.38
0114 Beldar day 1.33 645.00 857.85
9999 Sundries L.S. 16.12 2.12 34.17
TOTAL 1146.68 W
Add 1 % Water charges on "W" 11.47
TOTAL 1158.15 X
Add GST on "X" (multiplying
factor 0.1405) 162.72
TOTAL 1320.87 Y
Add 15% CPOH on "Y" 198.13
TOTAL 1519.00 Z
Add Cess @ 1% on "Z" 15.19
Cost of 5.14 quintal 1534.19
Cost of one quintal 298.48
Say 298.50
18.24 Laying in position S&S or flanged C.I. special such as tees, bends, collars,
tapers and caps etc.(excluding cost of specials).
Code Description Unit Quantity Rate Amount
Details of cost for 7 quintal
10 Nos. Tee 200x150mm Weight
= 70x10 = 700kg.
LABOUR for laying tee-
0116 Fitter (grade 1) day 0.93 784.00 729.12
0117 Assistant Fitter or 2nd class Fitter day 0.62 714.00 442.68
0114 Beldar day 2.48 645.00 1599.60
SUB HEAD : 18- WATER SUPPLY 1535
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 40.17 2.12 85.16
TOTAL 2856.56 W
Add 1 % Water charges on "W" 28.57
TOTAL 2885.13 X
Add GST on "X" (multiplying
factor 0.1405) 405.36
TOTAL 3290.49 Y
Add 15% CPOH on "Y" 493.57
TOTAL 3784.06 Z
Add Cess @ 1% on "Z" 37.84
Cost of 7 quintal 3821.90
Cost of one quintal 545.99
Say 546.00
18.25 Providing and laying S&S C.I. standard specials such as tees, bends, collars,
tapers, caps etc. (Heavy class):
18.25.1 Up to 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
1464 S & S.C.I.standard specials upto
300 mm dia (heavy class) quintal 1.00 3800.00 3800.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
LABOUR
18.24 Rate as per item No. 18.24 Of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 4360.57 W
Add 1 % Water charges on "W-A" 38.15
TOTAL 4398.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 541.31
TOTAL 4940.02 Y
Add 15% CPOH on "Y-A" 659.10
TOTAL 5599.13 Z
Add Cess @ 1% on "Z-A" 50.53
Cost of one quintal 5649.66
Say 5649.65
18.25.2 Over 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
1466 S & S.C.I.standard specials over
300 mm dia (heavy class) quintal 1.00 3800.00 3800.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
SUB HEAD : 18- WATER SUPPLY 1536
Code Description Unit Quantity Rate Amount
LABOUR
For laying
18.24 Rate as per item No. 18.24 Of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 4360.57 W
Add 1 % Water charges on "W-A" 38.15
TOTAL 4398.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 541.31
TOTAL 4940.02 Y
Add 15% CPOH on "Y-A" 659.10
TOTAL 5599.13 Z
Add Cess @ 1% on "Z-A" 50.53
Cost of one quintal 5649.66
Say 5649.65
18.26 Providing and laying flanged C.I. standard specials such as tees, bends, collars,
tapers, caps etc., suitable for flanged jointing as per IS : 1538 :
18.26.1 Up to 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
1468 Flanged C.I. standard specials upto
300 mm dia(heavy class) quintal 1.00 5700.00 5700.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
LABOUR
For laying
18.24 Rate as per item No. 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 6260.57 W
Add 1 % Water charges on "W-A" 57.15
TOTAL 6317.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 810.93
TOTAL 7128.64 Y
Add 15% CPOH on "Y-A" 987.40
TOTAL 8116.04 Z
Add Cess @ 1% on "Z-A" 75.70
Cost of one quintal 8191.74
Say 8191.75
18.26.2 Over 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
1470 Flanged C.I. standard specials over
300 mm dia(heavy class) quintal 1.00 5250.00 5250.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
SUB HEAD : 18- WATER SUPPLY 1537
Code Description Unit Quantity Rate Amount
LABOUR
For laying
18.24 Rate as per item No. 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 5810.57 W
Add 1 % Water charges on "W-A" 52.65
TOTAL 5863.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 747.07
TOTAL 6610.29 Y
Add 15% CPOH on "Y-A" 909.64
TOTAL 7519.93 Z
Add Cess @ 1% on "Z-A" 69.74
Cost of one quintal 7589.67
Say 7589.65
18.27 Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA)
conforming to IS - 1536 :
18.27.1 100 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
100mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 19.820 Kg
Weight of 10m pipes 19.820x10
= 198.20 Kg
7697 S&S Centrifugally (Spun) C.I. Pipe
class LA 100mm dia metre 10.00 857.00 8570.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.10 358.32 35.83
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 1.98 298.50 591.03 A
TOTAL 9196.86 W
Add 1 % Water charges on "W-A" 86.06
TOTAL 9282.92 X
Add GST on "X-A" (multiplying
factor 0.1405) 1221.21
TOTAL 10504.13 Y
Add 15% CPOH on "Y-A" 1486.97
TOTAL 11991.10 Z
Add Cess @ 1% on "Z-A" 114.00
Cost of 10 metre 12105.10
Cost of one metre 1210.51
Say 1210.50
SUB HEAD : 18- WATER SUPPLY 1538
18.27.2 125 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
125mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 25.820 Kg
Weight of 10m pipes 25.820x10
= 258.20 Kg
7698 S&S Centrifugally (Spun) C.I. Pipe
class LA 125mm dia metre 10.00 1067.00 10670.00
2320 Carriage of Spun iron S & S pipes
125 mm dia 100 metre 0.10 478.64 47.86
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 2.58 298.50 770.13 A
TOTAL 11487.99 W
Add 1 % Water charges on "W-A" 107.18
TOTAL 11595.17 X
Add GST on "X-A" (multiplying
factor 0.1405) 1520.92
TOTAL 13116.09 Y
Add 15% CPOH on "Y-A" 1851.89
TOTAL 14967.99 Z
Add Cess @ 1% on "Z-A" 141.98
Cost of 10 metre 15109.96
Cost of one metre 1511.00
Say 1511.00
18.27.3 150 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
150mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 32.180 Kg
Weight of 10m pipes 32.180x10
= 321.80 Kg
7699 S&S Centrifugally (Spun) C.I. Pipe
class LA 150mm dia metre 10.00 1286.00 12860.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.10 597.20 59.72
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 3.22 298.50 961.17 A
TOTAL 13880.89 W
Add 1 % Water charges on "W-A" 129.20
TOTAL 14010.09 X
Add GST on "X-A" (multiplying
factor 0.1405) 1833.37
TOTAL 15843.46 Y
Add 15% CPOH on "Y-A" 2232.34
TOTAL 18075.80 Z
Add Cess @ 1% on "Z-A" 171.15
Cost of 10 metre 18246.95
Cost of one metre 1824.69
Say 1824.70
SUB HEAD : 18- WATER SUPPLY 1539
18.27.4 200 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
200mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 47.090 Kg
Weight of 10m pipes 47.090x10
= 470.90 Kg
7700 S&S Centrifugally (Spun) C.I. Pipe
class LA 200mm dia metre 10.00 2190.00 21900.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.10 971.45 97.15
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 4.71 298.50 1405.94 A
TOTAL 23403.08 W
Add 1 % Water charges on "W-A" 219.97
TOTAL 23623.05 X
Add GST on "X-A" (multiplying
factor 0.1405) 3121.50
TOTAL 26744.56 Y
Add 15% CPOH on "Y-A" 3800.79
TOTAL 30545.35 Z
Add Cess @ 1% on "Z-A" 291.39
Cost of 10 metre 30836.74
Cost of one metre 3083.67
Say 3083.65
18.27.5 250 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIALS
250mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 63.450 Kg
Weight of 10m pipes 63.450x10
= 634.50 Kg
7701 S&S Centrifugally (Spun) C.I. Pipe
class LA 250mm dia metre 10.00 2857.00 28570.00
2323 Carriage of Spun iron S & S pipes
250 mm dia 100 metre 0.10 1380.48 138.05
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 6.35 298.50 1895.48 A
TOTAL 30603.52 W
Add 1 % Water charges on "W-A" 287.08
TOTAL 30890.60 X
Add GST on "X-A" (multiplying
factor 0.1405) 4073.82
TOTAL 34964.42 Y
Add 15% CPOH on "Y-A" 4960.34
TOTAL 39924.76 Z
Add Cess @ 1% on "Z-A" 380.29
Cost of 10 metre 40305.05
Cost of one metre 4030.51
Say 4030.50
SUB HEAD : 18- WATER SUPPLY 1540
18.27.6 300 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
300mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 81.820 Kg
Weight of 10m pipes 81.820x10
= 818.20 Kg
7702 S&S Centrifugally (Spun) C.I. Pipe
class LA 300mm dia metre 10.00 3857.00 38570.00
2324 Carriage of Spun iron S & S pipes
300 mm dia 100 metre 0.10 1706.30 170.63
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 8.18 298.50 2441.73 A
TOTAL 41182.36 W
Add 1 % Water charges on "W-A" 387.41
TOTAL 41569.77 X
Add GST on "X-A" (multiplying
factor 0.1405) 5497.49
TOTAL 47067.26 Y
Add 15% CPOH on "Y-A" 6693.83
TOTAL 53761.08 Z
Add Cess @ 1% on "Z-A" 513.19
Cost of 10 metre 54274.28
Cost of one metre 5427.43
Say 5427.45
18.27.7 350 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
350mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 103.10 Kg
Weight of 10m pipes 103.10x10
= 1031.00 Kg
7703 S&S Centrifugally (Spun) C.I. Pipe
class LA 350mm dia metre 10.00 4619.00 46190.00
2325 Carriage of Spun iron S & S pipes
350 mm dia 100 metre 0.10 2388.82 238.88
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 10.31 298.50 3077.54 A
TOTAL 49506.42 W
Add 1 % Water charges on "W-A" 464.29
TOTAL 49970.71 X
Add GST on "X-A" (multiplying
factor 0.1405) 6588.49
TOTAL 56559.20 Y
Add 15% CPOH on "Y-A" 8022.25
TOTAL 64581.45 Z
Add Cess @ 1% on "Z-A" 615.04
Cost of 10 metre 65196.48
Cost of one metre 6519.65
Say 6519.65
SUB HEAD : 18- WATER SUPPLY 1541
18.27.8 400 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
400mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 125.45 Kg
Weight of 10m pipes 125.45x10
= 1254.50 Kg
7704 S&S Centrifugally (Spun) C.I. Pipe
class LA 400mm dia metre 10.00 6095.00 60950.00
2326 Carriage of Spun iron S & S pipes
400 mm dia 100 metre 0.10 3257.48 325.75
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 12.55 298.50 3746.18 A
TOTAL 65021.92 W
Add 1 % Water charges on "W-A" 612.76
TOTAL 65634.68 X
Add GST on "X-A" (multiplying
factor 0.1405) 8695.34
TOTAL 74330.02 Y
Add 15% CPOH on "Y-A" 10587.58
TOTAL 84917.59 Z
Add Cess @ 1% on "Z-A" 811.71
Cost of 10 metre 85729.31
Cost of one metre 8572.93
Say 8572.95
18.27.9 450 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
450mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 151.270 Kg
Weight of 10m pipes 151.270x10
= 1512.70 Kg
7705 S&S Centrifugally (Spun) C.I. Pipe
class LA 450mm dia metre 10.00 7381.00 73810.00
2327 Carriage of Spun iron S & S pipes
450 mm dia 100 metre 0.10 3981.36 398.14
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 15.13 298.50 4516.31 A
TOTAL 78724.44 W
Add 1 % Water charges on "W-A" 742.08
TOTAL 79466.52 X
Add GST on "X-A" (multiplying
factor 0.1405) 10530.51
TOTAL 89997.03 Y
Add 15% CPOH on "Y-A" 12822.11
TOTAL 102819.14 Z
Add Cess @ 1% on "Z-A" 983.03
Cost for 10 metre 103802.16
Cost of one metre 10380.22
Say 10380.20
SUB HEAD : 18- WATER SUPPLY 1542
18.27.10 500 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
500mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 177.090 Kg
Weight of 10m pipes 177.090x10
= 1770.90 Kg
7706 S&S Centrifugally (Spun) C.I. Pipe
class LA 500mm dia metre 10.00 8571.00 85710.00
2328 Carriage of Spun iron S & S pipes
500 mm dia 100 metre 0.10 3981.36 398.14
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 17.71 298.50 5286.44 A
TOTAL 91394.57 W
Add 1 % Water charges on "W-A" 861.08
TOTAL 92255.65 X
Add GST on "X-A" (multiplying
factor 0.1405) 12219.18
TOTAL 104474.83 Y
Add 15% CPOH on "Y-A" 14878.26
TOTAL 119353.09 Z
Add Cess @ 1% on "Z-A" 1140.67
Cost of 10 metre 120493.75
Cost of one metre 12049.38
Say 12049.40
18.27.11 600 mm dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
600mm dia. spun iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 236.000 Kg
Weight of 10m pipes 236.000x10
= 2360.00 Kg
7707 S&S Centrifugally (Spun) C.I. Pipe
class LA 600mm dia metre 10.00 11995.00 119950.00
2329 Carriage of Spun iron S & S pipes
600mm dia 100 metre 0.10 5972.04 597.20
LABOUR for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 23.60 298.50 7044.60 A
TOTAL 127591.80 W
Add 1 % Water charges on "W-A" 1205.47
TOTAL 128797.28 X
Add GST on "X-A" (multiplying
factor 0.1405) 17106.25
TOTAL 145903.53 Y
Add 15% CPOH on "Y-A" 20828.84
TOTAL 166732.37 Z
Add Cess @ 1% on "Z-A" 1596.88
Cost of 10 metre 168329.24
Cost of 1 metre 16832.92
Say 16832.90
SUB HEAD : 18- WATER SUPPLY 1543
18.28 Providing lead caulked joints to spun iron or C.I. pipes and specials, including
testing of joints but excluding the cost of pig lead :
18.28.1 100 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 1.70 55.00 93.50
0.17x 10 =1.70 kg
0761 Fuel wood quintal 0.28 500.00 140.00
0771 Kerosene oil litre 0.38 50.00 19.00
9999 Sundries L.S. 6.76 2.12 14.33
9977 Carriage of materials L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0117 Assistant Fitter or 2nd class Fitter day 1.00 714.00 714.00
0114 Beldar day 2.00 645.00 1290.00
TOTAL 3066.13 W
Add 1 % Water charges on "W" 30.66
TOTAL 3096.79 X
Add GST on "X" (multiplying
factor 0.1405) 435.10
TOTAL 3531.89 Y
Add 15% CPOH on "Y" 529.78
TOTAL 4061.68 Z
Add Cess @ 1% on "Z" 40.62
Cost of 10 joints 4102.29
Cost of one joint 410.23
Say 410.25
18.28.2 125 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 2.00 55.00 110.00
0.20x10=2.00 kg
0761 Fuel wood quintal 0.37 500.00 185.00
0771 Kerosene oil litre 0.76 50.00 38.00
9999 Sundries L.S. 9.49 2.12 20.12
9977 Carriage of materials L.S. 9.49 2.12 20.12
LABOUR
0116 Fitter (grade 1) day 1.50 784.00 1176.00
0117 Assistant Fitter or 2nd class Fitter day 1.50 714.00 1071.00
0114 Beldar day 3.00 645.00 1935.00
TOTAL 4555.24 W
Add 1 % Water charges on "W" 45.55
TOTAL 4600.79 X
Add GST on "X" (multiplying
factor 0.1405) 646.41
TOTAL 5247.20 Y
Add 15% CPOH on "Y" 787.08
TOTAL 6034.28 Z
Add Cess @ 1% on "Z" 60.34
Cost of 10 joints 6094.62
Cost of one joint 609.46
Say 609.45
SUB HEAD : 18- WATER SUPPLY 1544
18.28.3 150 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 2.30 55.00 126.50
0.23x10=2.30 kg
0761 Fuel wood quintal 0.42 500.00 210.00
0771 Kerosene oil litre 0.76 50.00 38.00
9999 Sundries L.S. 10.79 2.12 22.87
9977 Carriage of materials L.S. 10.79 2.12 22.87
LABOUR
0116 Fitter (grade 1) day 1.50 784.00 1176.00
0117 Assistant Fitter or 2nd class Fitter day 1.50 714.00 1071.00
0114 Beldar day 3.00 645.00 1935.00
TOTAL 4602.25 W
Add 1 % Water charges on "W" 46.02
TOTAL 4648.27 X
Add GST on "X" (multiplying
factor 0.1405) 653.08
TOTAL 5301.35 Y
Add 15% CPOH on "Y" 795.20
TOTAL 6096.56 Z
Add Cess @ 1% on "Z" 60.97
Cost of 10 joints 6157.52
Cost of one joint 615.75
Say 615.75
18.28.4 200 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 3.00 55.00 165.00
0.3x10=3.00 kg
0761 Fuel wood quintal 0.56 500.00 280.00
0771 Kerosene oil litre 0.76 50.00 38.00
9999 Sundries L.S. 13.52 2.12 28.66
9977 Carriage of materials L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0117 Assistant Fitter or 2nd class Fitter day 2.00 714.00 1428.00
0114 Beldar day 4.00 645.00 2580.00
TOTAL 6116.32 W
Add 1 % Water charges on "W" 61.16
TOTAL 6177.49 X
Add GST on "X" (multiplying
factor 0.1405) 867.94
TOTAL 7045.43 Y
Add 15% CPOH on "Y" 1056.81
TOTAL 8102.24 Z
Add Cess @ 1% on "Z" 81.02
Cost of 10 joints 8183.26
Cost of one joint 818.33
Say 818.35
SUB HEAD : 18- WATER SUPPLY 1545
18.28.5 250 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 4.00 55.00 220.00
0.4x10=4 00 kg
0761 Fuel wood quintal 0.65 500.00 325.00
0771 Kerosene oil litre 1.14 50.00 57.00
9999 Sundries L.S. 17.55 2.12 37.21
9977 Carriage of materials L.S. 17.55 2.12 37.21
LABOUR
0116 Fitter (grade 1) day 2.50 784.00 1960.00
0117 Assistant Fitter or 2nd class Fitter day 2.50 714.00 1785.00
0114 Beldar day 5.00 645.00 3225.00
TOTAL 7646.41 W
Add 1 % Water charges on "W" 76.46
TOTAL 7722.88 X
Add GST on "X" (multiplying
factor 0.1405) 1085.06
TOTAL 8807.94 Y
Add 15% CPOH on "Y" 1321.19
TOTAL 10129.13 Z
Add Cess @ 1% on "Z" 101.29
Cost of 10 joints 10230.42
Cost of one joint 1023.04
Say 1023.05
18.28.6 300 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 5.40 55.00 297.00
0.54x10 =5.40 kg
0761 Fuel wood quintal 0.75 500.00 375.00
0771 Kerosene oil litre 1.52 50.00 76.00
9999 Sundries L.S. 20.28 2.12 42.99
9977 Carriage of materials L.S. 20.28 2.12 42.99
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0117 Assistant Fitter or 2nd class Fitter day 3.00 714.00 2142.00
0114 Beldar day 6.00 645.00 3870.00
TOTAL 9197.99 W
Add 1 % Water charges on "W" 91.98
TOTAL 9289.97 X
Add GST on "X" (multiplying
factor 0.1405) 1305.24
TOTAL 10595.21 Y
Add 15% CPOH on "Y" 1589.28
TOTAL 12184.49 Z
Add Cess @ 1% on "Z" 121.84
Cost of 10 joints 12306.33
Cost of one joint 1230.63
Say 1230.65
SUB HEAD : 18- WATER SUPPLY 1546
18.28.7 350 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 6.20 55.00 341.00
0.62x10=6.20 kg
0761 Fuel wood quintal 0.93 500.00 465.00
0771 Kerosene oil litre 1.70 50.00 85.00
9999 Sundries L.S. 24.18 2.12 51.26
9977 Carriage of materials L.S. 24.18 2.12 51.26
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0117 Assistant Fitter or 2nd class Fitter day 3.00 714.00 2142.00
0114 Beldar day 6.00 645.00 3870.00
TOTAL 9357.52 W
Add 1 % Water charges on "W" 93.58
TOTAL 9451.10 X
Add GST on "X" (multiplying
factor 0.1405) 1327.88
TOTAL 10778.98 Y
Add 15% CPOH on "Y" 1616.85
TOTAL 12395.82 Z
Add Cess @ 1% on "Z" 123.96
Cost of 10 joints 12519.78
Cost of one joint 1251.98
Say 1252.00
18.28.8 400 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 7.40 55.00 407.00
0761 Fuel wood quintal 1.12 500.00 560.00
0.74x10=7.40 kg
0771 Kerosene oil litre 1.70 50.00 85.00
9999 Sundries L.S. 26.91 2.12 57.05
9977 Carriage of materials L.S. 26.91 2.12 57.05
LABOUR
0116 Fitter (grade 1) day 4.00 784.00 3136.00
0117 Assistant Fitter or 2nd class Fitter day 4.00 714.00 2856.00
0114 Beldar day 8.00 645.00 5160.00
TOTAL 12318.10 W
Add 1 % Water charges on "W" 123.18
TOTAL 12441.28 X
Add GST on "X" (multiplying
factor 0.1405) 1748.00
TOTAL 14189.28 Y
Add 15% CPOH on "Y" 2128.39
TOTAL 16317.67 Z
Add Cess @ 1% on "Z" 163.18
Cost of 10 joints 16480.85
Cost of one joint 1648.08
Say 1648.10
SUB HEAD : 18- WATER SUPPLY 1547
18.28.9 450 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 7.90 55.00 434.50
0.79x10=7.90 kg
0761 Fuel wood quintal 1.21 500.00 605.00
0771 Kerosene oil litre 2.27 50.00 113.50
9999 Sundries L.S. 31.07 2.12 65.87
9977 Carriage of materials L.S. 31.07 2.12 65.87
LABOUR
0116 Fitter (grade 1) day 4.50 784.00 3528.00
0117 Assistant Fitter or 2nd class Fitter day 4.50 714.00 3213.00
0114 Beldar day 9.00 645.00 5805.00
TOTAL 13830.74 W
Add 1 % Water charges on "W" 138.31
TOTAL 13969.04 X
Add GST on "X" (multiplying
factor 0.1405) 1962.65
TOTAL 15931.69 Y
Add 15% CPOH on "Y" 2389.75
TOTAL 18321.45 Z
Add Cess @ 1% on "Z" 183.21
Cost of 10 joints 18504.66
Cost of one joint 1850.47
Say 1850.45
18.28.10 500 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 8.50 55.00 467.50
0.85x10=8.50 kg
0761 Fuel wood quintal 1.31 500.00 655.00
0771 Kerosene oil litre 2.27 50.00 113.50
9999 Sundries L.S. 33.67 2.12 71.38
9977 Carriage of materials L.S. 33.67 2.12 71.38
LABOUR
0116 Fitter (grade 1) day 4.75 784.00 3724.00
0117 Assistant Fitter or 2nd class Fitter day 4.75 714.00 3391.50
0114 Beldar day 9.50 645.00 6127.50
TOTAL 14621.76 W
Add 1 % Water charges on "W" 146.22
TOTAL 14767.98 X
Add GST on "X" (multiplying
factor 0.1405) 2074.90
TOTAL 16842.88 Y
Add 15% CPOH on "Y" 2526.43
TOTAL 19369.31 Z
Add Cess @ 1% on "Z" 193.69
Cost of 10 joints 19563.00
Cost of one joint 1956.30
Say 1956.30
SUB HEAD : 18- WATER SUPPLY 1548
18.28.11 600 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1881 Spun yarn kilogram 10.20 55.00 561.00
1.02x10=10.20 kg
0761 Fuel wood quintal 1.68 500.00 840.00
0771 Kerosene oil litre 2.84 50.00 142.00
9999 Sundries L.S. 40.30 2.12 85.44
9977 Carriage of materials L.S. 40.30 2.12 85.44
LABOUR
0116 Fitter (grade 1) day 6.50 784.00 5096.00
0117 Assistant Fitter or 2nd class Fitter day 6.50 714.00 4641.00
0114 Beldar day 13.00 645.00 8385.00
TOTAL 19835.87 W
Add 1 % Water charges on "W" 198.36
TOTAL 20034.23 X
Add GST on "X" (multiplying
factor 0.1405) 2814.81
TOTAL 22849.04 Y
Add 15% CPOH on "Y" 3427.36
TOTAL 26276.40 Z
Add Cess @ 1% on "Z" 262.76
Cost of 10 joints 26539.16
Cost of one joint 2653.92
Say 2653.90
18.29 Supplying pig lead at site of work.
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
1397 Pig lead kilogram 100.00 210.00 21000.00
2341 Carriage of Pig lead tonne 0.10 145.72 14.57
TOTAL 21014.57 W
Add 1 % Water charges on "W" 210.15
TOTAL 21224.72 X
Add GST on "X" (multiplying
factor 0.1405) 2982.07
TOTAL 24206.79 Y
Add 15% CPOH on "Y" 3631.02
TOTAL 27837.81 Z
Add Cess @ 1% on "Z" 278.38
Cost of one quintal 28116.19
Say 28116.20
SUB HEAD : 18- WATER SUPPLY 1549
18.30 Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including
testing of joints :
18.30.1 80 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1373 Rubber insertions for 80 mm dia
pipe joints each 10.00 16.00 160.00
1956 Bolts and nuts 16 mm dia 60 mm long each 40.00 11.50 460.00
9977 Carriage of materials L.S. 2.73 2.12 5.79
LABOUR
0116 Fitter (grade 1) day 0.15 784.00 117.60
0117 Assistant Fitter or 2nd class Fitter day 0.15 714.00 107.10
0114 Beldar day 0.80 645.00 516.00
TOTAL 1366.49 W
Add 1 % Water charges on "W" 13.66
TOTAL 1380.15 X
Add GST on "X" (multiplying
factor 0.1405) 193.91
TOTAL 1574.06 Y
Add 15% CPOH on "Y" 236.11
TOTAL 1810.17 Z
Add Cess @ 1% on "Z" 18.10
Cost for 10 joints 1828.28
Cost for one joint 182.83
Say 182.85
18.30.2 100 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1374 Rubber insertions for 100 mm dia
pipe joints each 10.00 18.00 180.00
1956 Bolts and nuts 16 mm dia 60 mm long each 80.00 11.50 920.00
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0117 Assistant Fitter or 2nd class Fitter day 0.25 714.00 178.50
0114 Beldar day 1.00 645.00 645.00
TOTAL 2128.32 W
Add 1 % Water charges on "W" 21.28
TOTAL 2149.60 X
Add GST on "X" (multiplying
factor 0.1405) 302.02
TOTAL 2451.62 Y
Add 15% CPOH on "Y" 367.74
TOTAL 2819.36 Z
Add Cess @ 1% on "Z" 28.19
Cost for 10 joints 2847.56
Cost for one joint 284.76
Say 284.75
SUB HEAD : 18- WATER SUPPLY 1550
18.30.3 125 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1375 Rubber insertions for 125 mm dia
pipe joints each 10.00 20.00 200.00
1957 Bolts and nuts 16 mm dia 65 mm long each 80.00 13.00 1040.00
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0117 Assistant Fitter or 2nd class Fitter day 0.25 714.00 178.50
0114 Beldar day 1.00 645.00 645.00
TOTAL 2268.32 W
Add 1 % Water charges on "W" 22.68
TOTAL 2291.00 X
Add GST on "X" (multiplying
factor 0.1405) 321.89
TOTAL 2612.89 Y
Add 15% CPOH on "Y" 391.93
TOTAL 3004.82 Z
Add Cess @ 1% on "Z" 30.05
Cost for 10 joints 3034.87
Cost for one joint 303.49
Say 303.50
18.30.4 150 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1376 Rubber insertions for 150 mm dia
pipe joints each 10.00 20.00 200.00
1958 Bolts and nuts 20 mm dia 65 mm long each 80.00 15.00 1200.00
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.30 784.00 235.20
0117 Assistant Fitter or 2nd class Fitter day 0.30 714.00 214.20
0114 Beldar day 1.10 645.00 709.50
TOTAL 2567.72 W
Add 1 % Water charges on "W" 25.68
TOTAL 2593.40 X
Add GST on "X" (multiplying
factor 0.1405) 364.37
TOTAL 2957.77 Y
Add 15% CPOH on "Y" 443.67
TOTAL 3401.43 Z
Add Cess @ 1% on "Z" 34.01
Cost for 10 joints 3435.45
Cost for one joint 343.54
Say 343.55
SUB HEAD : 18- WATER SUPPLY 1551
18.30.5 200 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1377 Rubber insertions for 200 mm dia
pipe joints each 10.00 25.00 250.00
1959 Bolts and nuts 20 mm dia 70 mm long each 80.00 17.50 1400.00
9977 Carriage of materials L.S. 4.16 2.12 8.82
LABOUR
0116 Fitter (grade 1) day 0.30 784.00 235.20
0117 Assistant Fitter or 2nd class Fitter day 0.30 714.00 214.20
0114 Beldar day 1.10 645.00 709.50
TOTAL 2817.72 W
Add 1 % Water charges on "W" 28.18
TOTAL 2845.90 X
Add GST on "X" (multiplying
factor 0.1405) 399.85
TOTAL 3245.74 Y
Add 15% CPOH on "Y" 486.86
TOTAL 3732.61 Z
Add Cess @ 1% on "Z" 37.33
Cost for 10 joints 3769.93
Cost for one joint 376.99
Say 377.00
18.30.6 250 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1378 Rubber insertions for 250 mm dia
pipe joints each 10.00 40.00 400.00
1960 Bolts and nuts 20 mm dia 75 mm long each 120.00 17.00 2040.00
9977 Carriage of materials L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.40 784.00 313.60
0117 Assistant Fitter or 2nd class Fitter day 0.40 714.00 285.60
0114 Beldar day 1.30 645.00 838.50
TOTAL 3889.00 W
Add 1 % Water charges on "W" 38.89
TOTAL 3927.89 X
Add GST on "X" (multiplying
factor 0.1405) 551.87
TOTAL 4479.76 Y
Add 15% CPOH on "Y" 671.96
TOTAL 5151.72 Z
Add Cess @ 1% on "Z" 51.52
Cost for 10 joints 5203.24
Cost for one joint 520.32
Say 520.30
SUB HEAD : 18- WATER SUPPLY 1552
18.30.7 300 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1379 Rubber insertions for 300 mm dia
pipe joints each 10.00 45.00 450.00
1960 Bolts and nuts 20 mm dia 75 mm long each 120.00 17.00 2040.00
9977 Carriage of materials L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.40 784.00 313.60
0117 Assistant Fitter or 2nd class Fitter day 0.40 714.00 285.60
0114 Beldar day 1.30 645.00 838.50
TOTAL 3939.00 W
Add 1 % Water charges on "W" 39.39
TOTAL 3978.39 X
Add GST on "X" (multiplying
factor 0.1405) 558.96
TOTAL 4537.35 Y
Add 15% CPOH on "Y" 680.60
TOTAL 5217.96 Z
Add Cess @ 1% on "Z" 52.18
Cost for 10 joints 5270.14
Cost for one joint 527.01
Say 527.00
18.30.8 350 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1380 Rubber insertions for 350 mm dia
pipe joints each 10.00 50.00 500.00
1961 Bolts and nuts 20 mm dia 80 mm long each 160.00 17.00 2720.00
9977 Carriage of materials L.S. 5.33 2.12 11.30
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0117 Assistant Fitter or 2nd class Fitter day 0.50 714.00 357.00
0114 Beldar day 1.50 645.00 967.50
TOTAL 4947.80 W
Add 1 % Water charges on "W" 49.48
TOTAL 4997.28 X
Add GST on "X" (multiplying
factor 0.1405) 702.12
TOTAL 5699.40 Y
Add 15% CPOH on "Y" 854.91
TOTAL 6554.30 Z
Add Cess @ 1% on "Z" 65.54
Cost for 10 joints 6619.85
Cost for one joint 661.98
Say 662.00
SUB HEAD : 18- WATER SUPPLY 1553
18.30.9 400 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1381 Rubber insertions for 400 mm dia
pipe joints each 10.00 73.00 730.00
1962 Bolts and nuts 24 mm dia 85 mm long each 160.00 27.00 4320.00
9977 Carriage of materials L.S. 8.06 2.12 17.09
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0117 Assistant Fitter or 2nd class Fitter day 0.50 714.00 357.00
0114 Beldar day 1.50 645.00 967.50
TOTAL 6783.59 W
Add 1 % Water charges on "W" 67.84
TOTAL 6851.42 X
Add GST on "X" (multiplying
factor 0.1405) 962.62
TOTAL 7814.05 Y
Add 15% CPOH on "Y" 1172.11
TOTAL 8986.16 Z
Add Cess @ 1% on "Z" 89.86
Cost for 10 joints 9076.02
Cost for one joint 907.60
Say 907.60
18.30.10 450 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1382 Rubber insertions for 450 mm dia
pipe joints each 10.00 92.00 920.00
1962 Bolts and nuts 24 mm dia 85 mm long each 200.00 27.00 5400.00
9977 Carriage of materials L.S. 8.06 2.12 17.09
LABOUR
0116 Fitter (grade 1) day 0.60 784.00 470.40
0117 Assistant Fitter or 2nd class Fitter day 0.60 714.00 428.40
0114 Beldar day 1.70 645.00 1096.50
TOTAL 8332.39 W
Add 1 % Water charges on "W" 83.32
TOTAL 8415.71 X
Add GST on "X" (multiplying
factor 0.1405) 1182.41
TOTAL 9598.12 Y
Add 15% CPOH on "Y" 1439.72
TOTAL 11037.84 Z
Add Cess @ 1% on "Z" 110.38
Cost for 10 joints 11148.21
Cost for one joint 1114.82
Say 1114.80
SUB HEAD : 18- WATER SUPPLY 1554
18.30.11 500 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1383 Rubber insertions for 500 mm dia
pipe joints each 10.00 110.00 1100.00
1963 Bolts and nuts 24 mm dia 90 mm long each 200.00 31.00 6200.00
9977 Carriage of materials L.S. 8.06 2.12 17.09
LABOUR
0116 Fitter (grade 1) day 0.65 784.00 509.60
0117 Assistant Fitter or 2nd class Fitter day 0.65 714.00 464.10
0114 Beldar day 1.80 645.00 1161.00
TOTAL 9451.79 W
Add 1 % Water charges on "W" 94.52
TOTAL 9546.31 X
Add GST on "X" (multiplying
factor 0.1405) 1341.26
TOTAL 10887.56 Y
Add 15% CPOH on "Y" 1633.13
TOTAL 12520.70 Z
Add Cess @ 1% on "Z" 125.21
Cost of 10 joints 12645.90
Cost for one joint 1264.59
Say 1264.60
18.30.12 600 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 joints
MATERIAL
1384 Rubber insertions for 600 mm dia
pipe joints each 10.00 125.00 1250.00
1964 Bolts and nuts 27 mm dia 100 mm long each 200.00 37.00 7400.00
9977 Carriage of materials L.S. 9.49 2.12 20.12
LABOUR
0116 Fitter (grade 1) day 0.75 784.00 588.00
0117 Assistant Fitter or 2nd class Fitter day 0.75 714.00 535.50
0114 Beldar day 2.00 645.00 1290.00
TOTAL 11083.62 W
Add 1 % Water charges on "W" 110.84
TOTAL 11194.45 X
Add GST on "X" (multiplying
factor 0.1405) 1572.82
TOTAL 12767.28 Y
Add 15% CPOH on "Y" 1915.09
TOTAL 14682.37 Z
Add Cess @ 1% on "Z" 146.82
Cost for 10 joints 14829.19
Cost for one joint 1482.92
Say 1482.90
SUB HEAD : 18- WATER SUPPLY 1555
18.31 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts,
rubber insertions etc. (the tail pieces if required will be paid separately) :
18.31.1 100 mm diameter
18.31.1.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1940 C.I.sluice valve (with caps) class I :
100 mm dia each 10.00 2450.00 24500.00
Carriage of sluice valves
wt.= 44.3x10=443kg= 0.443t. say 0.44t
2309 Carriage of Cast iron fittings tonne 0.44 145.72 64.12
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 4.43 546.00 2418.78 A
Providing flanged joints to sluice valves
with bolts, nuts and rubber insertion etc.
18.30.2 (Rate as per item No.18.30.2 Of
SH: Water Supply) each 20.00 284.75 5695.00 A
TOTAL 32677.90 W
Add 1 % Water charges on "W-A" 245.64
TOTAL 32923.54 X
Add GST on "X-A" (multiplying
factor 0.1405) 3485.77
TOTAL 36409.31 Y
Add 15% CPOH on "Y-A" 4244.33
TOTAL 40653.64 Z
Add Cess @ 1% on "Z-A" 325.40
Cost of 10 valves 40979.04
Cost of 1 valve 4097.90
Say 4097.90
18.31.1.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3311 C.I.sluice valve (with caps) class II :
100 mm dia each 10.00 2700.00 27000.00
Carriage of sluice valves
56.3x10=563kg= 0.563t=0.56t
2309 Carriage of Cast iron fittings tonne 0.56 145.72 81.60
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 5.63 546.00 3073.98 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
SUB HEAD : 18- WATER SUPPLY 1556
Code Description Unit Quantity Rate Amount
18.30.2 (Rate as per item No.18.30.2 Of
SH: Water Supply) each 20.00 284.75 5695.00 A
TOTAL 35850.58 W
Add 1 % Water charges on "W-A" 270.82
TOTAL 36121.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 3843.01
TOTAL 39964.41 Y
Add 15% CPOH on "Y-A" 4679.32
TOTAL 44643.73 Z
Add Cess @ 1% on "Z-A" 358.75
Cost of 10 valves 45002.48
Cost of 1 valve 4500.25
Say 4500.25
18.31.2 125 mm diameter
18.31.2.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1941 C.I.sluice valve (with caps) class I :
125 mm dia each 10.00 2610.00 26100.00
Carriage of sluice valves
wt. = 56.3x10=563kg = 0.563t.
say 0.56t
2309 Carriage of Cast iron fittings tonne 0.56 145.72 81.60
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 5.63 546.00 3073.98 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.3 (Rate as per item No.18.30.3 Of
SH: Water Supply) each 20.00 303.50 6070.00 A
TOTAL 35325.58 W
Add 1 % Water charges on "W-A" 261.82
TOTAL 35587.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 3715.30
TOTAL 39302.70 Y
Add 15% CPOH on "Y-A" 4523.81
TOTAL 43826.51 Z
Add Cess @ 1% on "Z-A" 346.83
Cost of 10 valves 44173.33
Cost of 1 valve 4417.33
Say 4417.35
SUB HEAD : 18- WATER SUPPLY 1557
18.31.2.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3314 C.I.sluice valve (with caps) class II :
125 mm dia each 10.00 3300.00 33000.00
Carriage of sluice valves
wt. = 68.3x10=683kg = 0.68t say 0.68t
2309 Carriage of Cast iron fittings tonne 0.68 145.72 99.09
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 6.83 546.00 3729.18 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.3 (Rate as per item No.18.30.3 Of
SH: Water Supply) each 20.00 303.50 6070.00 A
TOTAL 42898.27 W
Add 1 % Water charges on "W-A" 330.99
TOTAL 43229.26 X
Add GST on "X-A" (multiplying
factor 0.1405) 4696.93
TOTAL 47926.19 Y
Add 15% CPOH on "Y-A" 5719.05
TOTAL 53645.24 Z
Add Cess @ 1% on "Z-A" 438.46
Cost of 10 valves 54083.70
Cost of 1 valve 5408.37
Say 5408.35
18.31.3 150 mm diameter
18.31.3.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1942 C.I.sluice valve (with caps) class I :
150 mm dia each 10.00 3650.00 36500.00
Carriage of sluice valves
wt. = 72.5x10=725kg = 0.725t.
say 0.72t
2309 Carriage of Cast iron fittings tonne 0.72 145.72 104.92
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 7.25 546.00 3958.50 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
SUB HEAD : 18- WATER SUPPLY 1558
Code Description Unit Quantity Rate Amount
18.30.4 (Rate as per item No.18.30.4 Of
SH: Water Supply) each 20.00 343.55 6871.00 A
TOTAL 47434.42 W
Add 1 % Water charges on "W-A" 366.05
TOTAL 47800.47 X
Add GST on "X-A" (multiplying
factor 0.1405) 5194.42
TOTAL 52994.89 Y
Add 15% CPOH on "Y-A" 6324.81
TOTAL 59319.70 Z
Add Cess @ 1% on "Z-A" 484.90
Cost of 10 valves 59804.60
Cost of 1 valve 5980.46
Say 5980.45
18.31.3.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3317 C.I.sluice valve (with caps) class II :
150 mm dia each 10.00 4100.00 41000.00
Carriage of sluice valves
wt. = 86.5x10=865kg = 0.865t.
say 0.865t
2309 Carriage of Cast iron fittings tonne 0.865 145.72 126.05
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 8.65 546.00 4722.90 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.4 (Rate as per item No.18.30.4 Of
SH: Water Supply) each 20.00 343.55 6871.00 A
TOTAL 52719.95 W
Add 1 % Water charges on "W-A" 411.26
TOTAL 53131.21 X
Add GST on "X-A" (multiplying
factor 0.1405) 5835.99
TOTAL 58967.20 Y
Add 15% CPOH on "Y-A" 7106.00
TOTAL 66073.20 Z
Add Cess @ 1% on "Z-A" 544.79
Cost of 10 valves 66617.99
Cost of 1 valve 6661.80
Say 6661.80
SUB HEAD : 18- WATER SUPPLY 1559
18.31.4 200 mm diameter
18.31.4.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1943 C.I.sluice valve (with caps) class I :
200 mm dia each 10.00 7600.00 76000.00
Carriage of sluice valves
wt. = 121.5x10=1215kg = 1.215t.
say 1.22t
2309 Carriage of Cast iron fittings tonne 1.22 145.72 177.78
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 12.15 546.00 6633.90 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.5 (Rate as per item No.18.30.5 Of
SH: Water Supply) each 20.00 377.00 7540.00 A
TOTAL 90351.68 W
Add 1 % Water charges on "W-A" 761.78
TOTAL 91113.46 X
Add GST on "X-A" (multiplying
factor 0.1405) 10810.01
TOTAL 101923.46 Y
Add 15% CPOH on "Y-A" 13162.43
TOTAL 115085.90 Z
Add Cess @ 1% on "Z-A" 1009.12
Cost of 10 valves 116095.02
Cost of 1 valve 11609.50
Say 11609.50
18.31.4.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3320 C.I.sluice valve (with caps) class II :
200 mm dia each 10.00 8900.00 89000.00
Carriage of sluice valves
wt. = 150.5x10=1505 kg = 1.5 t.
say 1.5 t
2309 Carriage of Cast iron fittings tonne 1.50 145.72 218.58
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 15.05 546.00 8217.30 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
SUB HEAD : 18- WATER SUPPLY 1560
Code Description Unit Quantity Rate Amount
18.30.5 (Rate as per item No.18.30.5 Of
SH: Water Supply) each 20.00 377.00 7540.00 A
TOTAL 104975.88 W
Add 1 % Water charges on "W-A" 892.19
TOTAL 105868.07 X
Add GST on "X-A" (multiplying
factor 0.1405) 12660.56
TOTAL 118528.63 Y
Add 15% CPOH on "Y-A" 15415.70
TOTAL 133944.33 Z
Add Cess @ 1% on "Z-A" 1181.87
Cost of 10 valves 135126.20
Cost of 1 valve 13512.62
Say 13512.60
18.31.5 250 mm diameter
18.31.5.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1944 C.I.sluice valve (with caps) class I :
250 mm dia each 10.00 10980.00 109800.00
Carriage of sluice valves
wt. = 179.9x10=1799kg = 1.799t.
say 1.80t
2309 Carriage of Cast iron fittings tonne 1.80 145.72 262.30
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 17.99 546.00 9822.54 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.6 (Rate as per item No.18.30.6 Of
SH: Water Supply) each 20.00 520.30 10406.00 A
TOTAL 130290.84 W
Add 1 % Water charges on "W-A" 1100.62
TOTAL 131391.46 X
Add GST on "X-A" (multiplying
factor 0.1405) 15618.39
TOTAL 147009.85 Y
Add 15% CPOH on "Y-A" 19017.20
TOTAL 166027.05 Z
Add Cess @ 1% on "Z-A" 1457.99
Cost of 10 valves 167485.03
Cost of 1 valve 16748.50
Say 16748.50
SUB HEAD : 18- WATER SUPPLY 1561
18.31.5.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3321 C.I.sluice valve (with caps) class II :
250 mm dia each 10.00 15000.00 150000.00
Carriage of sluice valves
wt. = 229.9x10=2299kg = 2299t.
say 2.30t
2309 Carriage of Cast iron fittings tonne 2.30 145.72 335.16
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 22.99 546.00 12552.54 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.6 (Rate as per item No.18.30.6 Of
SH: Water Supply) each 20.00 520.30 10406.00 A
TOTAL 173293.70 W
Add 1 % Water charges on "W-A" 1503.35
TOTAL 174797.05 X
Add GST on "X-A" (multiplying
factor 0.1405) 21333.31
TOTAL 196130.36 Y
Add 15% CPOH on "Y-A" 25975.77
TOTAL 222106.13 Z
Add Cess @ 1% on "Z-A" 1991.48
Cost of 10 valves 224097.61
Cost of 1 valve 22409.76
Say 22409.75
18.31.6 300 mm diameter
18.31.6.1 Class I
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
1945 C.I.sluice valve (with caps) class I :
300 mm dia each 10.00 15500.00 155000.00
Carriage of sluice valves
wt. = 242.4x10=2424kg = 2.424t.
say 2.42t
2309 Carriage of Cast iron fittings tonne 2.42 145.72 352.64
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 24.24 546.00 13235.04 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
SUB HEAD : 18- WATER SUPPLY 1562
Code Description Unit Quantity Rate Amount
18.30.7 (Rate as per item No.18.30.7 Of
SH: Water Supply) each 20.00 527.00 10540.00 A
TOTAL 179127.68 W
Add 1 % Water charges on "W-A" 1553.53
TOTAL 180681.21 X
Add GST on "X-A" (multiplying
factor 0.1405) 22045.32
TOTAL 202726.53 Y
Add 15% CPOH on "Y-A" 26842.72
TOTAL 229569.25 Z
Add Cess @ 1% on "Z-A" 2057.94
Cost of 10 valves 231627.19
Cost of 1 valve 23162.72
Say 23162.70
18.31.6.2 Class II
Code Description Unit Quantity Rate Amount
Details of cost for 10 sluice valves
MATERIAL
3326 C.I.sluice valve (with caps) class II :
300 mm dia each 10.00 18500.00 185000.00
Carriage of sluice valves
wt. = 303.4x10=3034kg = 3.304t.
Say 3.03 tonne.
2309 Carriage of Cast iron fittings tonne 3.03 145.72 441.53
LABOUR for laying sluice valve
18.24 (Rate as per item No. 18.24 Of
SH: Water Supply) quintal 30.34 546.00 16565.64 A
Providing flanged joints to sluice
valves with bolts, nuts and rubber
insertion etc.
18.30.7 (Rate as per item No.18.30.7 Of
SH: Water Supply) each 20.00 527.00 10540.00 A
TOTAL 212547.17 W
Add 1 % Water charges on "W-A" 1854.42
TOTAL 214401.59 X
Add GST on "X-A" (multiplying
factor 0.1405) 26315.08
TOTAL 240716.67 Y
Add 15% CPOH on "Y-A" 32041.65
TOTAL 272758.32 Z
Add Cess @ 1% on "Z-A" 2456.53
Cost of 10 valves 275214.85
Cost of 1 valve 27521.48
Say 27521.50
SUB HEAD : 18- WATER SUPPLY 1563
18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement
mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box
100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4
mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine
sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a
floating coat of neat cement complete as per standard design :
18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
0.68x0.68x0.65m=0.301cum.
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 0.30 286.85 86.055 A
2.25 Rate as per item No.2.25 cum 0.30 253.95 76.19 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
0.68x0.68x0.075m=0.035cum.
Say 0.04 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete work cum 0.04 5660.45 226.42 A
(iii) Second class brick work in cement
mortar 1:4 (1 Cement : 4 coarse sand)
in foundations and plinth
1.66mx0.115x0.50m=0.095cum.
Say 0.10 cum.
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.10 6882.00 688.20 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
1.20x0.50=0.60sqm
0.30x0.30=0.09sqm.
Total =0.69sqm. Say 0.70sqm.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.70 386.55 270.59 A
1304 Surface box for stop cock each 1.00 125.00 125.00
(vi)
9977 Carriage of C.I. surface box L.S. 1.43 2.12 3.03
(vii) Cement concrete 1:2:4 (1 Cement
: 2 Coarse sand : 4 graded stone
aggregate 20mm nominal size) in slab
= 0.53mx0.53mx0.075m =
0.02107cum.
Less surface box 0.112x0.112x0.076
=(-)0.00094 cum.
= 0.0201 cum. Say 0.02cum.
5.3 Rate as per item No.5.3 SH : R.C.C cum 0.02 10719.30 214.39 A
(viii) Less labour for not lifting the
materilas upto floor five level
SUB HEAD : 18- WATER SUPPLY 1564
Code Description Unit Quantity Rate Amount
0115 Coolie day -0.038 645.00 -24.51
(ix)
9999 Sundries L.S. 4.16 2.12 8.82
TOTAL 1674.17 W
Add 1 % Water charges on "W-A" 1.12
TOTAL 1675.29 X
Add GST on "X-A" (multiplying
factor 0.1405) 15.94
TOTAL 1691.23 Y
Add 15% CPOH on "Y-A" 19.41
TOTAL 1710.65 Z
Add Cess @ 1% on "Z-A" 1.49
Cost of one manhole 1712.13
Say 1712.15
18.33 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement
mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box
100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with
chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation
concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat cement complete as
per standard design :
18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
1.21x1.21x1.00m=1.464cum.
Say 1.46 cum.
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 1.46 286.85 418.80 A
2.25 Rate as per item No.2.25 of
SH: Earth Work cum 1.46 253.95 370.77 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
1.21x1.21x0.1m=0.146cum.
Say 0.15 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.15 5660.45 849.07 A
(iii) Second class brick work in cement
mortar 1: 4(1 Cement : 4coarse sand)
in foundations and plinth
3.32mx0.23mx0.75m=0.573cum.
Say 0.57 cum.
SUB HEAD : 18- WATER SUPPLY 1565
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.57 6882.00 3922.74 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
2.40x0.75=1.80sqm.
0.60x0.60=0.36sqm.
Total = 2.16sqm.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.16 386.55 834.95 A
(v) C.I. surface box with hinged cover
100x100x75mm (inside)
1305 Surface box for sluice valve each 1.00 210.00 210.00
(vi)
9977 Carriage of C.I. surface box L.S. 8.06 2.12 17.09
(vii) Cement concrete 1:2:4 (1 Cement :
2 Coarse sand ; 4 graded stone
aggregate 20mm nominal size)
in slab = 1.06mx1.06mx0.15m
= 0.1685 cum.
Less surface box 3.142/4xd2x0.18m --
0.7854x0.156mx0.156mx0.18
= (-)0.0034 cum.
= 0.1651 cum. Say 0.17 cum.
5.3 Rate as per item No.5.3 Of SH: RCC cum 0.17 10719.30 1822.28 A
(viii) Less labour for not lifting the
materilas upto floor five level
0115 Coolie day -0.32 645.00 -206.40
(ix) Mild steel reinforcement for
RCC work etc.
0.165cum.x80kg/cum. = 13.2kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 13.20 88.95 1174.14 A
(x) Form work 0.60mx0.60m
=0.36sqm.+
3.32mx0.15m=0.50sqm.
= 0.86 sqm.
5.9.3 Rate as per item No.5.9.3 Of sqm 0.86 766.55 659.23 A
SH: RCC (xi)
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 10089.75 W
Add 1 % Water charges on "W-A" 0.38
TOTAL 10090.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 5.36
TOTAL 10095.49 Y
Add 15% CPOH on "Y-A" 6.53
TOTAL 10102.02 Z
Add Cess @ 1% on "Z-A" 0.50
Cost of one manhole 10102.52
Say 10102.50
SUB HEAD : 18- WATER SUPPLY 1566
18.34 Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement
mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box
100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with
chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation
concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse
sand) 12 mm thick, finished with a floating coat of neat cement complete as
per standard design :
18.34.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
1.51X1.51X1.25 m = 2.85cum.
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 2.85 286.85 817.5225 A
2.25 Rate as per item No.2.25 of
SH: Earth work cum 2.85 253.95 723.76 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
1.51x1.51x0.1m=0.228cum.
Say 0.23 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.23 5660.45 1301.90 A
(iii) Second class brick work in cement
foundations and plinth foundations and
plinth
4.52mx0.23mx1.00m=1.04cum.
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 1.04 6882.00 7157.28 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
3.60mx1.00m=3.60sqm
0.90mx0.90m
=0.81sqm.
Total=4.41sqm.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 4.41 386.55 1704.69 A
(v) C.I. surface box with chained lid.
1305 Surface box for sluice valve each 1.00 210.00 210.00
9977 (vi) Carriage of C.I. surface box L.S. 8.06 2.12 17.09
(vii) Cement concrete 1:2:4 (1 Cement
: 2 Coarse sand ; 4 graded stone
aggregate 20mm nominal size) in slab
= 1.36mx1.36mx0.15m = 0.2774 cum.
Less surface box 0.7854x0.156mx
0.156mx
0.18m = (-)0.0034 cum.
= 0.2740 cum. Say 0.27 cum.
SUB HEAD : 18- WATER SUPPLY 1567
Code Description Unit Quantity Rate Amount
5.3 Rate as per item No.5.3 Of SH: RCC cum 0.27 10719.30 2894.21 A
(viii) Less labour for not lifting the
materilas upto floor five level
0115 Coolie day -0.51 645.00 -328.95
(ix) Mild steel reinforcement for
RCC work etc.
0.274cum.x80kg/cum. = 21.92 kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 21.92 88.95 1949.78 A
(x) Form work
0.90mx0.90m=0.81sqm.+
4.52mx0.15m = 0.68 sqm.
Total= 1.49 sqm.
5.9.3 Rate as per item No.5.9.3 Of SH: RCC sqm 1.49 766.55 1142.16 A
(xi)
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 17606.53 W
Add 1 % Water charges on "W-A" -0.85
TOTAL 17605.68 X
Add GST on "X-A" (multiplying
factor 0.1405) -12.03
TOTAL 17593.65 Y
Add 15% CPOH on "Y-A" -14.65
TOTAL 17579.00 Z
Add Cess @ 1% on "Z-A" -1.12
Cost of one manhole 17577.88
Say 17577.90
18.35 Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement
mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box
100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside)
with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) , i/c necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate
40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :
3 coarse sand) 12 mm thick, finished with a floating coat of neat cement
complete as per standard design :
18.35.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
1.81X1.81X1.25M
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 4.10 286.85 1176.09 A
SUB HEAD : 18- WATER SUPPLY 1568
Code Description Unit Quantity Rate Amount
2.25 Rate as per item No.2.25 of
SH: Earth work cum 4.10 253.95 1041.20 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
1.81x1.81x0.1m=0.328cum.
Say 0.33 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.33 5660.45 1867.95 A
(iii) Second class brick work in cement
mortar 1:4 (1 Cement : 4coarse sand)
in foundations and plinth
5.72mx0.23mx1.00m=1.316cum.
Say 1.32 cum.
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 1.32 6882.00 9084.24 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
4.80mx1.00m=4.80sqm.
1.20mx1.20m=1.44sqm.
Total=6.42sqm.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 6.42 386.55 2481.65 A
(v) C.I. surface box with chained lid
1305 Surface box for sluice valve each 1.00 210.00 210.00
9977 (vi) Carriage of C.I. surface box L.S. 8.06 2.12 17.09
(vii) Cement concrete 1:2:4 (1 Cement
: 2 Coarse sand : 4 graded stone
aggregate 20mm nominal size)
in slab = 1.66mx1.66mx0.15m
= 0.4133 cum.
Less surface box 0.7854x0.156mx
0.156mx0.18m = (-)0.0034 cum.
Total= 0.4099 cum. Say 0.41 cum.
5.3 Rate as per item No.5.3 Of SH: RCC cum 0.41 10719.30 4394.91 A
(viii) Less labour for not lifting the
materilas upto floor five level
0115 Coolie day -0.77 645.00 -496.65
(ix) Mild steel reinforcement for
RCC slab steel @ 80kg/cum.
0.41cum.x80kg/cum. = 32.80kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 32.80 88.95 2917.56 A
(x) Form work
1.20mx1.20m=1.44sqm.+
5.72mx0.15m=0.86 sqm.
Total = 2.30sqm.
5.9.3 Rate as per item No.5.9.3 Of SH: RCC sqm 2.30 766.55 1763.07 A
(xi)
SUB HEAD : 18- WATER SUPPLY 1569
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 24474.18 W
Add 1 % Water charges on "W-A" -2.52
TOTAL 24471.66 X
Add GST on "X-A" (multiplying
factor 0.1405) -35.83
TOTAL 24435.83 Y
Add 15% CPOH on "Y-A" -43.62
TOTAL 24392.21 Z
Add Cess @ 1% on "Z-A" -3.34
Cost of one manhole 24388.86
Say 24388.85
18.36 Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement
mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box
350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab
1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine
sand:10 graded stone aggregate 40 mm nominal size) and inside plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with
a floating coat of neat cement complete as per standard design :
18.36.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
1.21X1.21X1.00m = 1.464cum.
Say 1.46cum.
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 1.46 286.85 418.80 A
2.25 Rate as per item No.2.25 of
SH: Earth work cum 1.46 253.95 370.77 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
1.21x1.21x0.1m=0.146cum. Say 0.15 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.15 5660.45 849.07 A
(iii) Second class brick work in cement
mortar 1:4 (1 Cement : 4 coarse sand)
in foundations and plinth
3.32mx0.23mx0.75m=0.573cum.
Say 0.57 cum.
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.57 6882.00 3922.74 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
2.40mx0.75m=1.80sqm.
0.90mx0.90m =0.36sqm.
Total=2.16sqm.
SUB HEAD : 18- WATER SUPPLY 1570
Code Description Unit Quantity Rate Amount
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.16 386.55 834.95 A
(v) C.I. surface box with chained lid
1305 Surface box for sluice valve each 1.00 210.00 210.00
9977 (vi) Carriage of C.I. surface box L.S. 53.82 2.12 114.10
(vii) Cement concrete 1:2:4 (1 Cement
: 2 Coarse sand ; 4 graded stone
aggregate 20mm nominal size)
in slab = 1.06mx1.06mx0.15m
= 0.1685 cum.
Less surface box 0.61x0.41mx0.15m=
(-)0.0375 cum.
= 0.131 cum. Say 0.13 cum.
5.3 Rate as per item No.5.3 Of SH: RCC cum 0.13 10719.30 1393.51 A
(viii) Less labour for not lifting the
materilas upto floor five level
0115 Coolie day -0.24 645.00 -154.80
(ix) Mild steel reinforcement for
RCC work etc.
0.131cumx80kg/cum. = 10.48kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 10.48 88.95 932.20 A
(x) Form work
0.60mx0.60m=0.36sqm.+
3.32mx0.15m = 0.50 sqm.
Total =0.86 sqm.
5.9.3 Rate as per item No.5.9.3 Of sqm 0.86 766.55 659.23 A
SH: RCC (xi)
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 9567.65 W
Add 1 % Water charges on "W-A" 1.86
TOTAL 9569.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 26.45
TOTAL 9595.96 Y
Add 15% CPOH on "Y-A" 32.20
TOTAL 9628.16 Z
Add Cess @ 1% on "Z-A" 2.47
Cost of one manhole 9630.63
Say 9630.65
18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement
mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I.
double flap surface box 400x200x200 mm (inside) with locking arrangement
and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) , i/c necessary excavation, foundation
concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm
nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3
coarse sand) 12 mm thick, finished with a floating coat of neat cement
complete as per standard design :
SUB HEAD : 18- WATER SUPPLY 1571
18.37.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
(i) Earth work in excavation including
refilling and disposal of surplus earth
1.21X1.06X0.85m = 1.09cum.
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 1.09 286.85 312.67 A
2.25 Rate as per item No.2.25 of
SH: Earth work cum 1.09 253.95 276.81 A
(ii) Cement concrete 1:5:10 (1 Cement
: 5 fine sand : 10 graded stone
aggregate 40mm nominal size)
1.21x1.06x0.1m=0.128cum.
Say 0.13 cum.
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.13 5660.45 735.86 A
(iii) Second class brick work in cement
mortar 1:4 (1 Cement : 4 coarse sand)
in foundations and plinth
3.02mx0.23mx0.50m=0.347cum.
Say 0.35 cum.
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.35 6882.00 2408.70 A
(iv) 12mm cement plaster 1:3 (1
Cement : 3 Coarse sand) finished with
a floating coat of neat cement.
2.10mx0.50m=1.05sqm.
0.60mx0.45m=0.27sqm.
Total=1.32sq
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.32 386.55 510.25 A
(v) C.I. surface box 400x200x200mm
(inside) with locking arrangement
1307 Surface box for water meter each 1.00 250.00 250.00
9977 (vi) Carriage of C.I. surface box L.S. 13.52 2.12 28.66
(vii) Cement concrete 1:2:4 (1 Cement
: 2 Coarse sand ; 4 graded stone
aggregate 20mm nominal size)
in slab = 1.06mx0.91mx0.25m
= 0.241 cum.
Less surface box 0.42x0.22mx0.2m
= (-)0.018 cum.
= 0.223 cum. Say 0.22 cum.
5.3 Rate as per item No.5.3 Of SH: RCC cum 0.22 10719.30 2358.25 A
(viii) Less labour for not lifting the
materilas upto floor five level
0115 Coolie day -0.41 645.00 -264.45
(ix) Mild steel reinforcement for
RCC work steel @ 80kg/cum.
0.223cum.x80kg/cum. = 17.84 kg.
SUB HEAD : 18- WATER SUPPLY 1572
Code Description Unit Quantity Rate Amount
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 17.84 88.95 1586.87 A
(x) Form work
0.60mx0.45m=0.27sqm.+
3.02mx0.25m=0.76sqm.
Total = 1.03sqm.
5.9.3 Rate as per item No.5.9.3 Of SH: RCC sqm 1.03 766.55 789.55 A
(xi)
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 9010.24 W
Add 1 % Water charges on "W-A" 0.31
TOTAL 9010.55 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.44
TOTAL 9014.99 Y
Add 15% CPOH on "Y-A" 5.41
TOTAL 9020.40 Z
Add Cess @ 1% on "Z-A" 0.41
Cost of one manhole 9020.81
Say 9020.80
18.38 Painting G.I. pipes and fittings with synthetic enamel white paint with two
coats over a ready mixed priming coat, both of approved quality for new
work :
18.38.1 15 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.0673 metre
Area=10x0.0673m = 0.673sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 0.673 55.50 37.35 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 0.673 131.45 88.47 A
9999 Add for delay L.S. 13.52 2.12 28.66
TOTAL 154.48 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 154.77 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 158.83 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 163.79 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 164.17
Cost of one metre 16.42
Say 16.40
SUB HEAD : 18- WATER SUPPLY 1573
18.38.2 20 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.0845 metre
Area = 10x0.0845 sqm. = 0.845 sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 0.845 55.50 46.90 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 0.845 131.45 111.08 A
9999 Add for delay L.S. 13.52 2.12 28.66
TOTAL 186.64 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 186.92 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 190.99 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 195.94 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 196.32
Cost of one metre 19.63
Say 19.65
18.38.3 25 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.1061 metre
Area = 10x0.1061 sqm. = 1.061 sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 1.061 55.50 58.89 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.061 131.45 139.47 A
9999 Add for delay L.S. 20.28 2.12 42.99
TOTAL 241.35 W
Add 1 % Water charges on "W-A" 0.43
TOTAL 241.78 X
Add GST on "X-A" (multiplying
factor 0.1405) 6.10
TOTAL 247.88 Y
Add 15% CPOH on "Y-A" 7.43
TOTAL 255.31 Z
Add Cess @ 1% on "Z-A" 0.57
Cost of 10 metre 255.88
Cost of one metre 25.59
Say 25.60
SUB HEAD : 18- WATER SUPPLY 1574
18.38.4 32 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.1334 metre
Area = 10x0.1334 sqm. = 1.334 sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 1.334 55.50 74.04 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.334 131.45 175.35 A
9999 Add for delay L.S. 20.28 2.12 42.99
TOTAL 292.38 W
Add 1 % Water charges on “W-A” 0.43
TOTAL 292.81 X
Add GST on “X-A” (multiplying
factor 0.1405) 6.10
TOTAL 298.92 Y
Add 15% CPOH on “Y-A” 7.43
TOTAL 306.34 Z
Add Cess @ 1% on “Z-A” 0.57
Cost of 10 metre 306.91
Cost of one metre 30.69
Say 30.70
18.38.5 40 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.1520 metre
Area = 10x0.1520 sqm. = 1.520 sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 1.52 55.50 84.36 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.52 131.45 199.80 A
9999 Add for delay L.S. 26.91 2.12 57.05
TOTAL 341.21 W
Add 1 % Water charges on "W-A" 0.57
TOTAL 341.78 X
Add GST on "X-A" (multiplying
factor 0.1405) 8.10
TOTAL 349.88 Y
Add 15% CPOH on "Y-A" 9.86
TOTAL 359.74 Z
Add Cess @ 1% on "Z-A" 0.76
Cost of 10 metre 360.49
Cost of one metre 36.05
Say 36.05
SUB HEAD : 18- WATER SUPPLY 1575
18.38.6 50 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Perimeter = 0.1894 metre
Area = 10x0.1894 sqm. = 1.894 sqm.
Priming coat-
13.50.3 Rate as per item no 13.50.3 of
SH : Finishing sqm 1.894 55.50 105.12 A
Painting two coats excluding priming
coat with white paint on new work.
13.61.1 Rate as per item no 13.61.1 of
SH : Finishing sqm 1.894 131.45 248.97 A
9999 Add for delay L.S. 26.91 2.12 57.05
TOTAL 411.13 W
Add 1 % Water charges on "W-A" 0.57
TOTAL 411.70 X
Add GST on "X-A" (multiplying
factor 0.1405) 8.10
TOTAL 419.80 Y
Add 15% CPOH on "Y-A" 9.86
TOTAL 429.66 Z
Add Cess @ 1% on "Z-A" 0.76
Cost of 10 metre 430.41
Cost of one metre 43.04
Say 43.05
18.39 Repainting G.I. pipes and fittings with synthetic enamel white paint with one
coat of approved quality :
18.39.1 15 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint
on old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 0.673 86.55 58.25 A
9999 Add for delay L.S. 8.06 2.12 17.09
TOTAL 75.34 W
Add 1 % Water charges on "W-A" 0.17
TOTAL 75.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.42
TOTAL 77.93 Y
Add 15% CPOH on "Y-A" 2.95
TOTAL 80.88 Z
Add Cess @ 1% on "Z-A" 0.23
Cost of 10 metre 81.11
Cost of one metre 8.11
Say 8.10
SUB HEAD : 18- WATER SUPPLY 1576
18.39.2 20 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint on
old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 0.845 86.55 73.13 A
9999 Add for delay L.S. 8.06 2.12 17.09
TOTAL 90.22 W
Add 1 % Water charges on "W-A" 0.17
TOTAL 90.39 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.42
TOTAL 92.82 Y
Add 15% CPOH on "Y-A" 2.95
TOTAL 95.77 Z
Add Cess @ 1% on "Z-A" 0.23
Cost of 10 metre 96.00
Cost of one metre 9.60
Say 9.60
18.39.3 25 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint on
old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 1.061 86.55 91.83 A
9999 Add for delay L.S. 10.79 2.12 22.87
TOTAL 114.70 W
Add 1 % Water charges on "W-A" 0.23
TOTAL 114.93 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.25
TOTAL 118.18 Y
Add 15% CPOH on "Y-A" 3.95
TOTAL 122.13 Z
Add Cess @ 1% on "Z-A" 0.30
Cost of 10 metre 122.43
Cost of one metre 12.24
Say 12.25
18.39.4 32 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint on
old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 1.334 86.55 115.46 A
SUB HEAD : 18- WATER SUPPLY 1577
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 10.92 2.12 23.15
TOTAL 138.61 W
Add 1 % Water charges on "W-A" 0.23
TOTAL 138.84 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.29
TOTAL 142.12 Y
Add 15% CPOH on "Y-A" 4.00
TOTAL 146.12 Z
Add Cess @ 1% on "Z-A" 0.31
Cost of 10 metre 146.43
Cost of one metre 14.64
Say 14.65
18.39.5 40 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint
on old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 1.52 86.55 131.56 A
9999 Add for delay L.S. 13.52 2.12 28.66
TOTAL 160.22 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 160.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 164.57 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 169.52 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 169.90
Cost of one metre 16.99
Say 17.00
18.39.6 50 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting one coat with white paint
on old work.
13.99.1 (Rate as per item no 13.99.1 of
S.H. Finishing) sqm 1.894 86.55 163.93 A
SUB HEAD : 18- WATER SUPPLY 1578
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 13.52 2.12 28.66
TOTAL 192.59 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 192.87 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 196.94 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 201.89 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 202.27
Cost of one metre 20.23
Say 20.25
18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic
paint of approved quality :
18.40.1 15 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1 sub-heads
finishing) sqm 0.673 115.10 77.46 A
9999 Add for delay L.S. 8.06 2.12 17.09
TOTAL 94.55 W
Add 1 % Water charges on “W-A” 0.17
TOTAL 94.72 X
Add GST on “X-A” (multiplying
factor 0.1405) 2.42
TOTAL 97.15 Y
Add 15% CPOH on “Y-A” 2.95
TOTAL 100.10 Z
Add Cess @ 1% on “Z-A” 0.23
Cost of 10 metre 100.32
Cost of one metre 10.03
Say 10.05
18.40.2 20 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 0.845 115.10 97.26 A
SUB HEAD : 18- WATER SUPPLY 1579
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 8.06 2.12 17.09
TOTAL 114.35 W
Add 1 % Water charges on "W-A" 0.17
TOTAL 114.52 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.42
TOTAL 116.94 Y
Add 15% CPOH on "Y-A" 2.95
TOTAL 119.89 Z
Add Cess @ 1% on "Z-A" 0.23
Cost of 10 metre 120.12
Cost of one metre 12.01
Say 12.00
18.40.3 25 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 1.061 115.10 122.12 A
9999 Add for delay L.S. 10.79 2.12 22.87
TOTAL 145.00 W
Add 1 % Water charges on "W-A" 0.23
TOTAL 145.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.25
TOTAL 148.47 Y
Add 15% CPOH on "Y-A" 3.95
TOTAL 152.42 Z
Add Cess @ 1% on "Z-A" 0.30
Cost of 10 metre 152.73
Cost of one metre 15.27
Say 15.25
18.40.4 32 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 1.334 115.10 153.54 A
SUB HEAD : 18- WATER SUPPLY 1580
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 10.79 2.12 22.87
TOTAL 176.42 W
Add 1 % Water charges on "W-A" 0.23
TOTAL 176.65 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.25
TOTAL 179.89 Y
Add 15% CPOH on "Y-A" 3.95
TOTAL 183.85 Z
Add Cess @ 1% on "Z-A" 0.30
Cost of 10 metre 184.15
Cost of one metre 18.41
Say 18.40
18.40.5 40 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 1.52 115.10 174.95 A
9999 Add for delay L.S. 12.22 2.12 25.91
TOTAL 200.86 W
Add 1 % Water charges on "W-A" 0.26
TOTAL 201.12 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.68
TOTAL 204.79 Y
Add 15% CPOH on "Y-A" 4.48
TOTAL 209.27 Z
Add Cess @ 1% on "Z-A" 0.34
Cost of 10 metre 209.61
Cost of one metre 20.96
Say 20.95
18.40.6 50 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 1.894 115.10 218.00 A
SUB HEAD : 18- WATER SUPPLY 1581
Code Description Unit Quantity Rate Amount
9999 Add for delay L.S. 12.22 2.12 25.91
TOTAL 243.91 W
Add 1 % Water charges on "W-A" 0.26
TOTAL 244.16 X
Add GST on "X-A" (multiplying
factor 0.1405) 3.68
TOTAL 247.84 Y
Add 15% CPOH on "Y-A" 4.48
TOTAL 252.32 Z
Add Cess @ 1% on "Z-A" 0.34
Cost of 10 metre 252.66
Cost of one metre 25.27
Say 25.25
18.40.7 65 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 2.387 115.10 274.74 A
9999 Add for delay L.S. 13.52 2.12 28.66
TOTAL 303.41 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 303.69 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 307.76 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 312.71 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 313.09
Cost of one metre 31.31
Say 31.30
18.40.8 80 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Painting with anti-corrosive paint
two coats.
13.65.1 (Rate as per item No.13.65.1
sub-heads finishing) sqm 2.796 115.10 321.82 A
9999 Add for delay L.S. 14.82 2.12 31.42
TOTAL 353.24 W
Add 1 % Water charges on "W-A" 0.31
TOTAL 353.55 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.46
TOTAL 358.01 Y
Add 15% CPOH on "Y-A" 5.43
TOTAL 363.44 Z
Add Cess @ 1% on "Z-A" 0.42
Cost of 10 metre 363.86
Cost of one metre 36.39
Say 36.40
SUB HEAD : 18- WATER SUPPLY 1582
18.41 Providing and filling sand of grading zone V or coarser grade, allround the
G.I. pipes in external work :
18.41.1 15 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
15mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 21.8mm
= 246.8mm say 247mm
Quantity of sand = 10x0.30x0.247
= 0.744 cum.
Less for pipe = 3.142/4(21.8)²x10
= (-)0.004 cum.
= 0.74 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.74 2131.25 1577.13 A
TOTAL 1577.13
Cost of 10 metre 1577.13
Cost of one metre 157.71
Say 157.70
18.41.1A Sub analysis item for sand filling component
Code Description Unit Quantity Rate Amount
Sub analysis item for sand filling
component
MATERIAL
6501 Sand zone V (Jamuna) cum 1.00 1300.00 1300.00
2335 Carriage of Jamuna sand cum 1.00 163.93 163.93
Labour:
0114 Beldar day 0.09 645.00 58.05
0115 Coolie day 0.11 645.00 70.95
TOTAL 1592.93 W
Add 1 % Water charges on "W" 15.93
TOTAL 1608.86 X
Add GST on "X" (multiplying
factor 0.1405) 226.04
TOTAL 1834.90 Y
Add 15% CPOH on "Y" 275.24
TOTAL 2110.14 Z
Add Cess @ 1% on "Z" 21.10
Cost of one cum. 2131.24
Say 2131.25
SUB HEAD : 18- WATER SUPPLY 1583
18.41.2 20 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
20mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 27.3mm
= 252.3 Say 252mm
Quantity of sand = 10x0.30x0.252
= 0.756 cum.+
Less for pipe =3.142/4(27.3)²x10
= (-)0.006cum.
= 0.750 cum
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.75 2131.25 1598.44 A
TOTAL 1598.44
Cost of 10 metre 1598.44
Cost of one metre 159.84
Say 159.85
18.41.3 25 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
25mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 34.2mm
= 259.2 Say 259mm
Quantity of sand = 10x0.30x0.259
= 0.777 cum.+
Less for pipe 3.142/4(34.2)²x10
= (-)0.009cum.
= 0.768 Say 0.77 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.77 2131.25 1641.06 A
TOTAL 1641.06
Cost of 10 metre 1641.06
Cost of one metre 164.11
Say 164.10
18.41.4 32 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
32mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
SUB HEAD : 18- WATER SUPPLY 1584
Code Description Unit Quantity Rate Amount
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 42.9mm
= 267.9 Say 268mm
Quantity of sand = 10x0.30x0.268
= 0.804 cum.+
Less for pipe 3.142/4(42.9)²x10
= (-)0.014cum.
= 0.790 Say 0.79 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.79 2131.25 1683.69 A
TOTAL 1683.69
Cost of 10 metre 1683.69
Cost of one metre 168.37
Say 168.35
18.41.5 40 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
40mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 48.8mm
= 273.8 Say 274mm
Quantity of sand = 10x0.30x0.274
= 0.82 cum.+
Less for pipe 3.142/4(48.8)²x10
= (-)0.014cum.
= 0.801 Say 0.80 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.8 2131.25 1705.00 A
TOTAL 1705.00
Cost of 10 metre 1705.00
Cost of one metre 170.50
Say 170.50
SUB HEAD : 18- WATER SUPPLY 1585
18.41.6 50 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
50mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 60.8mm
= 285.8 Say 286mm
Quantity of sand = 10x0.30x0.286
= 0.858 cum.+
Less for pipe 3.142/4(60.8)²x10
= (-)0.029cum.
= 0.829 Say 0.83 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 0.83 2131.25 1768.94 A
TOTAL 1768.94
Cost of 10 metre 1768.94
Cost of one metre 176.89
Say 176.90
18.41.7 65 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
65mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 76.6mm
= 301.6 Say 302mm
Quantity of sand = 10x0.45x0.302
= 1.359 cum.+
Less for pipe 3.142/4(76.6)²x10
= (-)0.046cum.
= 1.313 Say 1.31 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 1.31 2131.25 2791.94 A
TOTAL 2791.94
Cost of 10 metre 2791.94
Cost of one metre 279.19
Say 279.20
SUB HEAD : 18- WATER SUPPLY 1586
18.41.8 80 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
80mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 89.9mm
= 314.9 Say 315mm
Quantity of sand = 10x0.45x0.315
= 1.418 cum.+
Less for pipe 3.142/4(89.9)²x10
= (-)0.0640cum.
= 1.354 Say 1.35 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 1.35 2131.25 2877.19 A
TOTAL 2877.19
Cost of 10 metre 2877.19
Cost of one metre 287.72
Say 287.70
18.41.9 100 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
100mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 115mm
= 340mm
Quantity of sand = 10x0.45x0.34
= 1.53 cum.+
Less for pipe 3.142/4(0.115)²x10
= (-)0.10cum.
= 1.43 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 1.43 2131.25 3047.69 A
TOTAL 3047.69
Cost of 10 metre 3047.69
Cost of one metre 304.77
Say 304.75
SUB HEAD : 18- WATER SUPPLY 1587
18.41.10 150 mm diameter pipe
Code Description Unit Quantity Rate Amount
Details of cost of sand filling alround
150mm dia. pipe 10 metre long.
Width of sand filling = 300mm
Depth of sand filling
Under the pipe = 75mm+
Above the pipe = 150mm+
Max. external dia of pipe = 166.5mm
= 391.50mm Say 0.392m
Quantity of sand = 10x0.60x0.392
= 2.35 cum.+
Less for pipe 3.142/4(0.167)²x10
= (-)0.22cum.
= 2.13 cum.
18.41.1A Rate as per Item Number 18.41.1A of
SH:Water supply cum 2.13 2131.25 4539.56 A
TOTAL 4539.56
Cost of 10 metre 4539.56
Cost of one metre 453.96
Say 453.95
18.42 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all
soils except ordinary hard rocks requiring blasting, including removing the
casing pipe after the hand pump / tube well is lowered and tested :
18.42.1 Up to 6 metres depth
Code Description Unit Quantity Rate Amount
Details of cost for 6m depth
LABOUR For boring and removing
the pipe-
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 3.00 645.00 1935.00
0010 Hire charges of Derrick monkey rope
and other accessories day 0.50 750.00 375.00
Depreciation @ 2% of the cost of
casing pipe 6metre @ Rs. per metre
1472 Casing pipe 100 mm dia metre 0.12 340.00 40.80
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 2771.46 W
Add 1 % Water charges on "W" 27.71
TOTAL 2799.18 X
Add GST on "X" (multiplying
factor 0.1405) 393.28
TOTAL 3192.46 Y
Add 15% CPOH on "Y" 478.87
TOTAL 3671.33 Z
Add Cess @ 1% on "Z" 36.71
Cost of 6 metre 3708.04
Cost of one metre 618.01
Say 618.00
SUB HEAD : 18- WATER SUPPLY 1588
18.42.2 Beyond 6 m and up to 12 m depth
Code Description Unit Quantity Rate Amount
Details of cost for 6m depth
LABOUR for boring and removing
the pipe-
0116 Fitter (grade 1) day 0.62 784.00 486.08
0114 Beldar day 3.50 645.00 2257.50
0010 Hire charges of Derrick monkey rope
and other accessories day 0.62 750.00 465.00
Depreciation @ 2% of the cost of
casing pipe 6metre @ Rs. per metre
1472 Casing pipe 100 mm dia metre 0.12 340.00 40.80
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 3278.04 W
Add 1 % Water charges on "W" 32.78
TOTAL 3310.82 X
Add GST on "X" (multiplying
factor 0.1405) 465.17
TOTAL 3775.99 Y
Add 15% CPOH on "Y" 566.40
TOTAL 4342.39 Z
Add Cess @ 1% on "Z" 43.42
Cost of 6 metre 4385.82
Cost of one metre 730.97
Say 730.95
18.42.3 Beyond 12 m and up to 18 m depth
Code Description Unit Quantity Rate Amount
Details of cost for 6m depth
LABOUR
For boring and removing the pipe-
0116 Fitter (grade 1) day 0.75 784.00 588.00
0114 Beldar day 4.00 645.00 2580.00
0010 Hire charges of Derrickmonkey rope
and other accessories day 0.75 750.00 562.50
Depreciation @ 2% of the cost of
casing pipe 6metre @ Rs. per metre
1472 Casing pipe 100 mm dia metre 0.12 340.00 40.80
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 3799.96 W
Add 1 % Water charges on "W" 38.00
TOTAL 3837.96 X
Add GST on "X" (multiplying
factor 0.1405) 539.23
TOTAL 4377.20 Y
Add 15% CPOH on "Y" 656.58
TOTAL 5033.78 Z
Add Cess @ 1% on "Z" 50.34
Cost of 6 metre 5084.11
Cost of one metre 847.35
Say 847.35
SUB HEAD : 18- WATER SUPPLY 1589
18.43 Providing and placing in position filters of 40 mm diameter G.I. pipe with
brass strainer of approved quality.
Code Description Unit Quantity Rate Amount
Details of cost for one strainer 1.5 long
MATERIAL
1882 Strainer brass 40 mm dia 1.5 metre long each 1.00 625.00 625.00
9977 Carriage to site L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.17 784.00 133.28
0114 Beldar day 0.17 645.00 109.65
9999 Sundreis including hamp white lead etc. L.S. 7.15 2.12 15.16
TOTAL 911.75 W
Add 1 % Water charges on "W" 9.12
TOTAL 920.87 X
Add GST on "X" (multiplying
factor 0.1405) 129.38
TOTAL 1050.25 Y
Add 15% CPOH on "Y" 157.54
TOTAL 1207.79 Z
Add Cess @ 1% on "Z" 12.08
Cost of 1.5 metre 1219.87
Cost of one metre 813.24
Say 813.25
18.44 Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe
for tube well including cleaning and priming the tube well.
Code Description Unit Quantity Rate Amount
Details of cost for a depth of 10 metre
MATERIAL
1549 G.I. pipes 40 mm dia metre 10.20 290.00 2958.00
Carriage of 40mm pipe(36.5kg)
Added 2% wastage and fitting
2271 Carriage of G.I. pipes below 100 mm dia tonne 0.03723 145.72 5.43
9999 White lead, hamp and oil etc. L.S. 6.76 2.12 14.33
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.75 645.00 483.75
9999 Sundries L.S. 7.25 2.12 15.37
TOTAL 3735.60 W
Add 1 % Water charges on "W" 37.36
TOTAL 3772.95 X
Add GST on "X" (multiplying
factor 0.1405) 530.10
TOTAL 4303.05 Y
Add 15% CPOH on "Y" 645.46
TOTAL 4948.51 Z
Add Cess @ 1% on "Z" 49.49
Cost for 10 metre 4998.00
Cost of one metre 499.80
Say 499.80
SUB HEAD : 18- WATER SUPPLY 1590
18.45 Providing and placing in position hand pump of approved quality for 40 mm
diameter G.I. pipe complete with all accessories.
Code Description Unit Quantity Rate Amount
Details of cost for one pump
MATERIAL
1693 S.C.I. hand pump each 1.00 700.00 700.00
9977 Carriage L.S. 13.52 2.12 28.66
LABOUR
0116 Fitter (grade 1) day 0.10 784.00 78.40
0114 Beldar day 0.10 645.00 64.50
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 880.93 W
Add 1 % Water charges on "W" 8.81
TOTAL 889.74 X
Add GST on "X" (multiplying
factor 0.1405) 125.01
TOTAL 1014.75 Y
Add 15% CPOH on "Y" 152.21
TOTAL 1166.96 Z
Add Cess @ 1% on "Z" 11.67
Cost for one hand pump 1178.63
Say 1178.65
18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading
the pipe and making long screws etc. complete (New work) :
18.46.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1641 G.I. Union 15 mm nominal bore each 1.00 35.00 35.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 196.05 W
Add 1 % Water charges on "W" 1.96
TOTAL 198.01 X
Add GST on "X" (multiplying
factor 0.1405) 27.82
TOTAL 225.83 Y
Add 15% CPOH on "Y" 33.87
TOTAL 259.70 Z
Add Cess @ 1% on "Z" 2.60
Cost for one no. 262.30
Say 262.30
SUB HEAD : 18- WATER SUPPLY 1591
18.46.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1642 G.I. Union 20 mm nominal bore each 1.00 55.00 55.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 216.05 W
Add 1 % Water charges on "W" 2.16
TOTAL 218.21 X
Add GST on "X" (multiplying
factor 0.1405) 30.66
TOTAL 248.87 Y
Add 15% CPOH on "Y" 37.33
TOTAL 286.20 Z
Add Cess @ 1% on "Z" 2.86
Cost for one no. 289.06
Say 289.05
18.46.3 25 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1643 G.I. Union 25 mm nominal bore each 1.00 115.00 115.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 276.05 W
Add 1 % Water charges on "W" 2.76
TOTAL 278.81 X
Add GST on "X" (multiplying
factor 0.1405) 39.17
TOTAL 317.98 Y
Add 15% CPOH on "Y" 47.70
TOTAL 365.68 Z
Add Cess @ 1% on "Z" 3.66
Cost for one no. 369.34
Say 369.35
18.46.4 32 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1644 G.I. Union 32 mm nominal bore each 1.00 145.00 145.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
SUB HEAD : 18- WATER SUPPLY 1592
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.11 645.00 70.95
TOTAL 306.05 W
Add 1 % Water charges on "W" 3.06
TOTAL 309.11 X
Add GST on "X" (multiplying
factor 0.1405) 43.43
TOTAL 352.54 Y
Add 15% CPOH on "Y" 52.88
TOTAL 405.42 Z
Add Cess @ 1% on "Z" 4.05
Cost for one no. 409.47
Say 409.45
18.46.5 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1645 G.I. Union 40 mm nominal bore each 1.00 230.00 230.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
TOTAL 391.05 W
Add 1 % Water charges on "W" 3.91
TOTAL 394.96 X
Add GST on "X" (multiplying
factor 0.1405) 55.49
TOTAL 450.45 Y
Add 15% CPOH on "Y" 67.57
TOTAL 518.02 Z
Add Cess @ 1% on "Z" 5.18
Cost for one no. 523.20
Say 523.20
18.46.6 50 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1646 G.I. Union 50 mm nominal bore each 1.00 310.00 310.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.15 784.00 117.60
0114 Beldar day 0.15 645.00 96.75
TOTAL 528.21 W
Add 1 % Water charges on "W" 5.28
TOTAL 533.49 X
Add GST on "X" (multiplying
factor 0.1405) 74.96
TOTAL 608.45 Y
Add 15% CPOH on "Y" 91.27
TOTAL 699.71 Z
Add Cess @ 1% on "Z" 7.00
Cost for one no. 706.71
Say 706.70
SUB HEAD : 18- WATER SUPPLY 1593
18.46.7 65 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1647 G.I. Union 65 mm nominal bore each 1.00 525.00 525.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.15 784.00 117.60
0114 Beldar day 0.15 645.00 96.75
TOTAL 743.21 W
Add 1 % Water charges on "W" 7.43
TOTAL 750.64 X
Add GST on "X" (multiplying
factor 0.1405) 105.46
TOTAL 856.11 Y
Add 15% CPOH on "Y" 128.42
TOTAL 984.52 Z
Add Cess @ 1% on "Z" 9.85
Cost for one no. 994.37
Say 994.35
18.46.8 80 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1648 G.I. Union 80mm nominal bore each 1.00 575.00 575.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.15 784.00 117.60
0114 Beldar day 0.15 645.00 96.75
TOTAL 793.21 W
Add 1 % Water charges on "W" 7.93
TOTAL 801.14 X
Add GST on "X" (multiplying
factor 0.1405) 112.56
TOTAL 913.70 Y
Add 15% CPOH on "Y" 137.06
TOTAL 1050.76 Z
Add Cess @ 1% on "Z" 10.51
Cost for one no. 1061.26
Say 1061.25
18.47 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading
the pipe and making long screws, including excavation, refilling the earth or
cutting of wall and making good the same complete wherever required :
18.47.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1641 G.I. Union 15 mm nominal bore each 1.00 35.00 35.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
SUB HEAD : 18- WATER SUPPLY 1594
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 510.43 W
Add 1 % Water charges on "W" 5.10
TOTAL 515.53 X
Add GST on "X" (multiplying
factor 0.1405) 72.43
TOTAL 587.97 Y
Add 15% CPOH on "Y" 88.19
TOTAL 676.16 Z
Add Cess @ 1% on "Z" 6.76
Cost for one no. 682.92
Say 682.90
18.47.2 20 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1642 G.I. Union 20 mm nominal bore each 1.00 55.00 55.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 530.43 W
Add 1 % Water charges on "W" 5.30
TOTAL 535.73 X
Add GST on "X" (multiplying
factor 0.1405) 75.27
TOTAL 611.00 Y
Add 15% CPOH on "Y" 91.65
TOTAL 702.65 Z
Add Cess @ 1% on "Z" 7.03
Cost for one no. 709.68
Say 709.70
18.47.3 25 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1643 G.I. Union 25 mm nominal bore each 1.00 115.00 115.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
SUB HEAD : 18- WATER SUPPLY 1595
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.33 645.00 212.85
TOTAL 590.43 W
Add 1 % Water charges on "W" 5.90
TOTAL 596.33 X
Add GST on "X" (multiplying
factor 0.1405) 83.78
TOTAL 680.12 Y
Add 15% CPOH on "Y" 102.02
TOTAL 782.14 Z
Add Cess @ 1% on "Z" 7.82
Cost for one no. 789.96
Say 789.95
18.47.4 32 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1644 G.I. Union 32 mm nominal bore each 1.00 145.00 145.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 620.43 W
Add 1 % Water charges on "W" 6.20
TOTAL 626.63 X
Add GST on "X" (multiplying
factor 0.1405) 88.04
TOTAL 714.67 Y
Add 15% CPOH on "Y" 107.20
TOTAL 821.88 Z
Add Cess @ 1% on "Z" 8.22
Cost for one no. 830.09
Say 830.10
18.47.5 40 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1645 G.I. Union 40 mm nominal bore each 1.00 230.00 230.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 0.33 645.00 212.85
TOTAL 705.43 W
Add 1 % Water charges on "W" 7.05
TOTAL 712.48 X
Add GST on "X" (multiplying
factor 0.1405) 100.10
TOTAL 812.59 Y
Add 15% CPOH on "Y" 121.89
TOTAL 934.47 Z
Add Cess @ 1% on "Z" 9.34
Cost for one no. 943.82
Say 943.80
SUB HEAD : 18- WATER SUPPLY 1596
18.47.6 50 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1646 G.I. Union 50 mm nominal bore each 1.00 310.00 310.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.45 784.00 352.80
0114 Beldar day 0.45 645.00 290.25
TOTAL 956.91 W
Add 1 % Water charges on "W" 9.57
TOTAL 966.48 X
Add GST on "X" (multiplying
factor 0.1405) 135.79
TOTAL 1102.27 Y
Add 15% CPOH on "Y" 165.34
TOTAL 1267.61 Z
Add Cess @ 1% on "Z" 12.68
Cost for one no. 1280.28
Say 1280.30
18.47.7 65 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1647 G.I. Union 65 mm nominal bore each 1.00 525.00 525.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.45 784.00 352.80
0114 Beldar day 0.45 645.00 290.25
TOTAL 1171.91 W
Add 1 % Water charges on "W" 11.72
TOTAL 1183.63 X
Add GST on "X" (multiplying
factor 0.1405) 166.30
TOTAL 1349.93 Y
Add 15% CPOH on "Y" 202.49
TOTAL 1552.42 Z
Add Cess @ 1% on "Z" 15.52
Cost for one no. 1567.94
Say 1567.95
18.47.8 80 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
1648 G.I. Union 80mm nominal bore each 1.00 575.00 575.00
9988 Carriage of materials and sundries L.S. 1.82 2.12 3.86
LABOUR
0116 Fitter (grade 1) day 0.45 784.00 352.80
SUB HEAD : 18- WATER SUPPLY 1597
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.45 645.00 290.25
TOTAL 1221.91 W
Add 1 % Water charges on "W" 12.22
TOTAL 1234.13 X
Add GST on "X" (multiplying
factor 0.1405) 173.39
TOTAL 1407.52 Y
Add 15% CPOH on "Y" 211.13
TOTAL 1618.65 Z
Add Cess @ 1% on "Z" 16.19
Cost for one no. 1634.84
Say 1634.85
18.48 Providing and placing on terrace (at all floor levels) polyethylene water
storage tank, IS : 12701 marked, with cover and suitable locking arrangement
and making necessary holes for inlet, outlet and overflow pipes but without
fittings and the base support for tank.
Code Description Unit Quantity Rate Amount
Details of cost for 500 litres
MATERIAL
1649 Polyethylene water storage tank with
cover and suitable locking arrangement per litre 500.00 6.10 3050.00
9977 Carriage to site L.S. 179.40 2.12 380.33
9999 Placing at terrace L.S. 89.70 2.12 190.16
TOTAL 3620.49 W
Add 1 % Water charges on "W" 36.20
TOTAL 3656.70 X
Add GST on "X" (multiplying
factor 0.1405) 513.77
TOTAL 4170.46 Y
Add 15% CPOH on "Y" 625.57
TOTAL 4796.03 Z
Add Cess @ 1% on "Z" 47.96
Cost for 500 litre 4843.99
Cost of one litre 9.69
Say 9.70
18.48A Providing and fixing rectangular high density polyethylene water storage
loft tank with cover, conforming to ISI : 12701, colour of opaque white or as
approved by Engineer-in-charge. The rate includes making necessary holes
for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for
tank shall be paid separately.
Code Description Unit Quantity Rate Amount
Details of cost for one no. tank of
500 litres
MATERIAL
1649 Polyethylene water storage tank with
cover and suitable locking arrangement per litre 500.00 6.10 3050.00
9977 Carriage to site L.S. 179.40 2.12 380.33
SUB HEAD : 18- WATER SUPPLY 1598
Code Description Unit Quantity Rate Amount
9999 Placing at terrace L.S. 89.70 2.12 190.16
TOTAL 3620.49 W
Add 1 % Water charges on "W" 36.20
TOTAL 3656.70 X
Add GST on "X" (multiplying
factor 0.1405) 513.77
TOTAL 4170.46 Y
Add 15% CPOH on "Y" 625.57
TOTAL 4796.03 Z
Add Cess @ 1% on "Z" 47.96
Cost of 500 liters 4843.99
Cost of 1 litre 9.69
Say 9.70
18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to
IS:8931 :
18.49.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7257 C.P. Brass bibcock 15 mm each 1.00 300.00 300.00
9988 Carrige of material and fixing charges L.S. 11.57 2.12 24.53
TOTAL 324.53 W
Add 1 % Water charges on "W" 3.25
TOTAL 327.77 X
Add GST on "X" (multiplying
factor 0.1405) 46.05
TOTAL 373.83 Y
Add 15% CPOH on "Y" 56.07
TOTAL 429.90 Z
Add Cess @ 1% on "Z" 4.30
Cost of 1 no. 434.20
Say 434.20
18.50 Providing and fixing C.P. brass long nose bib cock of approved quality
conforming to IS standards and weighing not less than 810 gms.
18.50.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7258 C.P. Brass long nose bibcock 15 mm each 1.00 500.00 500.00
9988 Carrige of material and fixing charges L.S. 16.25 2.12 34.45
TOTAL 534.45 W
Add 1 % Water charges on "W" 5.34
TOTAL 539.79 X
Add GST on "X" (multiplying
factor 0.1405) 75.84
TOTAL 615.64 Y
Add 15% CPOH on "Y" 92.35
TOTAL 707.98 Z
Add Cess @ 1% on "Z" 7.08
Cost of 1 no. 715.06
Say 715.05
SUB HEAD : 18- WATER SUPPLY 1599
18.51 Providing and fixing C.P. brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms.
18.51.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7259 C.P. Brass long body bibcock 15 mm each 1.00 500.00 500.00
9988 Carrige of material and fixing charges L.S. 13.91 2.12 29.49
TOTAL 529.49 W
Add 1 % Water charges on "W" 5.29
TOTAL 534.78 X
Add GST on "X" (multiplying
factor 0.1405) 75.14
TOTAL 609.92 Y
Add 15% CPOH on "Y" 91.49
TOTAL 701.41 Z
Add Cess @ 1% on "Z" 7.01
Cost of 1 no. 708.42
Say 708.40
18.52 Providing and fixing C.P. brass stop cock (concealed) of standard design
and of approved make conforming to IS:8931.
18.52.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7260 C.P. Brass stop cock (concealed)
15 mm each 1.00 420.00 420.00
9988 Carrige of material and fixing charges L.S. 11.57 2.12 24.53
TOTAL 444.53 W
Add 1 % Water charges on "W" 4.45
TOTAL 448.97 X
Add GST on "X" (multiplying
factor 0.1405) 63.08
TOTAL 512.05 Y
Add 15% CPOH on "Y" 76.81
TOTAL 588.86 Z
Add Cess @ 1% on "Z" 5.89
Cost of 1 no. 594.75
Say 594.75
18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points
of approved quality conforming to IS:8931
18.53.1 15mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7261 C.P. Brass angle valve 15 mm each 1.00 350.00 350.00
SUB HEAD : 18- WATER SUPPLY 1600
Code Description Unit Quantity Rate Amount
9988 Carriage and fixing charges L.S. 11.31 2.12 23.98
TOTAL 373.98 W
Add 1 % Water charges on "W" 3.74
TOTAL 377.72 X
Add GST on "X" (multiplying
factor 0.1405) 53.07
TOTAL 430.79 Y
Add 15% CPOH on "Y" 64.62
TOTAL 495.40 Z
Add Cess @ 1% on "Z" 4.95
Cost of 1 no. 500.36
Say 500.35
18.53A Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of
approved make and quality as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
0593 C.P. Brass Extension Nipple
(1/2"x2" size) each 1.00 40.00 40.00
9999 Sundries L.S. 2.89 2.12 6.13
TOTAL 46.13 W
Add 1 % Water charges on "W" 0.46
TOTAL 46.59 X
Add GST on "X" (multiplying
factor 0.1405) 6.55
TOTAL 53.13 Y
Add 15% CPOH on "Y" 7.97
TOTAL 61.10 Z
Add Cess @ 1% on "Z" 0.61
Cost of 1 no. 61.71
Say 61.70
18.54 Providing and fixing PTMT bib cock of approved quality and colour.
18.54.1 15mm nominal bore, 86 mm long, weighing not less than 88 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7400 15 mm PTMT bib cock each 1.00 65.00 65.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 82.09 W
Add 1 % Water charges on "W" 0.82
TOTAL 82.91 X
Add GST on "X" (multiplying
factor 0.1405) 11.65
TOTAL 94.56 Y
Add 15% CPOH on "Y" 14.18
TOTAL 108.74 Z
Add Cess @ 1% on "Z" 1.09
Cost of 1 no. 109.83
Say 109.85
SUB HEAD : 18- WATER SUPPLY 1601
18.54.2 15 mm nominal bore, 122mm long, weighing not less than 99 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7401 15 mm PTMT bib cockwith flange (fancy) each 1.00 90.00 90.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 107.09 W
Add 1 % Water charges on "W" 1.07
TOTAL 108.16 X
Add GST on "X" (multiplying
factor 0.1405) 15.20
TOTAL 123.35 Y
Add 15% CPOH on "Y" 18.50
TOTAL 141.86 Z
Add Cess @ 1% on "Z" 1.42
Cost of 1 no. 143.28
Say 143.30
18.54.3 15 mm nominal bore, 165 mm long, weighing not less than 110 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7402 15 mm PTMT bib cock long body
with flange each 1.00 100.00 100.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 117.09 W
Add 1 % Water charges on "W" 1.17
TOTAL 118.26 X
Add GST on "X" (multiplying
factor 0.1405) 16.62
TOTAL 134.87 Y
Add 15% CPOH on "Y" 20.23
TOTAL 155.10 Z
Add Cess @ 1% on "Z" 1.55
Cost of 1 No.. 156.66
Say 156.65
18.54.4 15 mm nominal bore, 90 mm long, weighing not less than 93 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7859 P.T.M.T. Bib cock with nozzle 15mm each 1.00 110.00 110.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 127.09 W
Add 1 % Water charges on "W" 1.27
TOTAL 128.36 X
Add GST on "X" (multiplying
factor 0.1405) 18.03
TOTAL 146.39 Y
Add 15% CPOH on "Y" 21.96
TOTAL 168.35 Z
Add Cess @ 1% on "Z" 1.68
Cost of 1 no. 170.03
Say 170.05
SUB HEAD : 18- WATER SUPPLY 1602
18.55 Providing and fixing PTMT stop cock of approved quality and colour.
18.55.1 15 mm nominal bore, 86 mm long, weighing not less than 88 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7403 15 mm dia PTMT stop cock
(male thread) each 1.00 60.00 60.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 77.09 W
Add 1 % Water charges on "W" 0.77
TOTAL 77.86 X
Add GST on "X" (multiplying
factor 0.1405) 10.94
TOTAL 88.80 Y
Add 15% CPOH on "Y" 13.32
TOTAL 102.12 Z
Add Cess @ 1% on "Z" 1.02
Cost of 1 no. 103.14
Say 103.15
18.55.2 20 mm nominal bore, 89 mm long, weighing not less than 88 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7405 20 mm dia. PTMT stop cock each 1.00 68.00 68.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 85.09 W
Add 1 % Water charges on "W" 0.85
TOTAL 85.94 X
Add GST on "X" (multiplying
factor 0.1405) 12.07
TOTAL 98.01 Y
Add 15% CPOH on "Y" 14.70
TOTAL 112.71 Z
Add Cess @ 1% on "Z" 1.13
Cost of 1 no. 113.84
Say 113.85
18.55.3 Concealed stop cock, 15 mm nominal bore, 108 mm long, weighing not less
than 108 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7861 P.T.M.T. Stop cock (concealed) 15mm each 1.00 120.00 120.00
SUB HEAD : 18- WATER SUPPLY 1603
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 137.09 W
Add 1 % Water charges on "W" 1.37
TOTAL 138.46 X
Add GST on "X" (multiplying
factor 0.1405) 19.45
TOTAL 157.91 Y
Add 15% CPOH on "Y" 23.69
TOTAL 181.60 Z
Add Cess @ 1% on "Z" 1.82
Cost of 1 no. 183.41
Say 183.40
18.56 Providing and fixing PTMT pillar cock of approved quality and colour.
18.56.1 15 mm nominal bore, 107 mm long, weighing not less than 110 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7406 PTMT pillar cock each 1.00 115.00 115.00
9988 Carriage of materials and fixing charges L.S. 9.49 2.12 20.12
TOTAL 135.12 W
Add 1 % Water charges on "W" 1.35
TOTAL 136.47 X
Add GST on "X" (multiplying
factor 0.1405) 19.17
TOTAL 155.64 Y
Add 15% CPOH on "Y" 23.35
TOTAL 178.99 Z
Add Cess @ 1% on "Z" 1.79
Cost of 1 no. 180.78
Say 180.80
18.56.2 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7410 PTMT pillar cock (fancy) 15 mm
foam flow. each 1.00 125.00 125.00
9988 Carriage of materials and fixing charges L.S. 9.49 2.12 20.12
TOTAL 145.12 W
Add 1 % Water charges on "W" 1.45
TOTAL 146.57 X
Add GST on "X" (multiplying
factor 0.1405) 20.59
TOTAL 167.16 Y
Add 15% CPOH on "Y" 25.07
TOTAL 192.24 Z
Add Cess @ 1% on "Z" 1.92
Cost of 1 no. 194.16
Say 194.15
SUB HEAD : 18- WATER SUPPLY 1604
18.57 Providing and fixing PTMT, push cock of approved quality and colour.
18.57.1 15 mm nominal bore, 98 mm long, weighing not less than 75 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7407 PTMT push cock 15 mm dia. each 1.00 55.00 55.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 72.09 W
Add 1 % Water charges on "W" 0.72
TOTAL 72.81 X
Add GST on "X" (multiplying
factor 0.1405) 10.23
TOTAL 83.04 Y
Add 15% CPOH on "Y" 12.46
TOTAL 95.49 Z
Add Cess @ 1% on "Z" 0.95
Cost of 1 no. 96.45
Say 96.45
18.57.2 15 mm nominal bore, 80 mm long, weighing not less than 46 gms
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7408 PTMT push cock 12 mm dia.
20 mm BSP each 1.00 45.00 45.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 62.09 W
Add 1 % Water charges on "W" 0.62
TOTAL 62.71 X
Add GST on "X" (multiplying
factor 0.1405) 8.81
TOTAL 71.52 Y
Add 15% CPOH on "Y" 10.73
TOTAL 82.25 Z
Add Cess @ 1% on "Z" 0.82
Cost of 1 no. 83.07
Say 83.05
18.58 Providing and fixing PTMT grating of approved quality and colour.
18.58.1 Circular type
18.58.1.1 100 mm nominal dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7409 PTMT grating 100 mm dia. each 1.00 16.00 16.00
SUB HEAD : 18- WATER SUPPLY 1605
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 4.16 2.12 8.82
TOTAL 24.82 W
Add 1 % Water charges on "W" 0.25
TOTAL 25.07 X
Add GST on "X" (multiplying
factor 0.1405) 3.52
TOTAL 28.59 Y
Add 15% CPOH on "Y" 4.29
TOTAL 32.88 Z
Add Cess @ 1% on "Z" 0.33
Cost of 1 no. 33.21
Say 33.20
18.58.1.2 125 mm nominal dia with 25 mm waste hole
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7411 125 mm grating withwaste hole each 1.00 25.00 25.00
9988 Carriage of materials and fixing charges L.S. 4.16 2.12 8.82
TOTAL 33.82 W
Add 1 % Water charges on "W" 0.34
TOTAL 34.16 X
Add GST on "X" (multiplying
factor 0.1405) 4.80
TOTAL 38.96 Y
Add 15% CPOH on "Y" 5.84
TOTAL 44.80 Z
Add Cess @ 1% on "Z" 0.45
Cost of 1 no. 45.25
Say 45.25
18.58.2 Rectangular type with openable circular lid
18.58.2.1 150 mm nominal size square 100 mm diameter of the inner hinged round grating
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
7412 Rectangular type with openable circular
lid 150 mm size 18 mm high with
100 mm dia. (110 gm) each 1.00 118.00 118.00
9988 Carriage of materials and fixing charges L.S. 4.16 2.12 8.82
TOTAL 126.82 W
Add 1 % Water charges on "W" 1.27
TOTAL 128.09 X
Add GST on "X" (multiplying
factor 0.1405) 18.00
TOTAL 146.08 Y
Add 15% CPOH on "Y" 21.91
TOTAL 168.00 Z
Add Cess @ 1% on "Z" 1.68
Cost of 1 no. 169.68
Say 169.70
SUB HEAD : 18- WATER SUPPLY 1606
18.59 Providing and fixing C.I. double acting air valve of approved quality with bolts,
nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will
be paid separately) :
18.59.1 50 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 10 no. double acting
air valves
MATERIAL
7415 Double acting air valve 50 mm each 10.00 3715.00 37150.00
9977 Carriage of air valves L.S. 26.00 2.12 55.12
9999 Labour for laying double acting air valve L.S. 39.00 2.12 82.68
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.1 (Rate as per item no 18.30.1 of
SH : Water Supply) each 10.00 182.85 1828.50 A
TOTAL 39116.30 W
Add 1 % Water charges on "W-A" 372.88
TOTAL 39489.18 X
Add GST on "X-A" (multiplying
factor 0.1405) 5291.33
TOTAL 44780.50 Y
Add 15% CPOH on "Y-A" 6442.80
TOTAL 51223.30 Z
Add Cess @ 1% on "Z-A" 493.95
Cost of 10 air valves 51717.25
Cost of 1 air valve 5171.73
Say 5171.75
18.59.2 80 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 10 no. double acting
air valves
MATERIAL
7416 Double acting air valve 80 mm each 10.00 4525.00 45250.00
9977 Carriage of air valves L.S. 26.00 2.12 55.12
9999 Labour for laying double acting air valve L.S. 39.00 2.12 82.68
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.1 (Rate as per item no 18.30.1 of
SH : Water Supply) each 10.00 182.85 1828.50 A
TOTAL 47216.30 W
Add 1 % Water charges on "W-A" 453.88
TOTAL 47670.18 X
Add GST on "X-A" (multiplying
factor 0.1405) 6440.76
TOTAL 54110.93 Y
Add 15% CPOH on "Y-A" 7842.37
TOTAL 61953.30 Z
Add Cess @ 1% on "Z-A" 601.25
Cost of 10 air valves 62554.55
Cost of 1 air valve 6255.45
Say 6255.45
SUB HEAD : 18- WATER SUPPLY 1607
18.59.3 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 10 no. double acting
air valves
MATERIAL
7417 Double acting air valve 100 mm each 10.00 5910.00 59100.00
9977 Carriage of air valves L.S. 26.00 2.12 55.12
9999 Labour for laying double acting air valve L.S. 52.00 2.12 110.24
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.2 (Rate as per item No.18.30.2 Of
SH:Water Supply) each 10.00 284.75 2847.50 A
TOTAL 62112.86 W
Add 1 % Water charges on "W-A" 592.65
TOTAL 62705.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 8410.05
TOTAL 71115.56 Y
Add 15% CPOH on "Y-A" 10240.21
TOTAL 81355.77 Z
Add Cess @ 1% on "Z-A" 785.08
Cost of 10 air valves 82140.86
Cost of 1 air valve 8214.09
Say 8214.10
18.60 Providing and fixing enclosed type water meter (bulk type) conforming to IS :
2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions
etc. (The tail pieces if required will be paid separately) :
18.60.1 80 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no. water meter
MATERIAL
7418 Water meter (including testing charges)
80 mm each 1.00 2030.00 2030.00
9977 Carriage of water meter L.S. 26.00 2.12 55.12
9999 Labour for laying water meter L.S. 39.00 2.12 82.68
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.1 (Rate as per item no 18.30.1 of
SH : Water Supply) each 2.00 182.85 365.70 A
TOTAL 2533.50 W
Add 1 % Water charges on "W-A" 21.68
TOTAL 2555.18 X
Add GST on "X-A" (multiplying
factor 0.1405) 307.62
TOTAL 2862.80 Y
Add 15% CPOH on "Y-A" 374.56
TOTAL 3237.36 Z
Add Cess @ 1% on "Z-A" 28.72
Cost of 1 water meter 3266.08
Say 3266.10
SUB HEAD : 18- WATER SUPPLY 1608
18.60.2 100 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no. water meter
MATERIAL
7419 Water meter (including testing charges)
100 mm each 1.00 3143.00 3143.00
9977 Carriage of water meter L.S. 26.00 2.12 55.12
9999 Labour for laying water meter L.S. 52.00 2.12 110.24
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.2 (Rate as per item No.18.30.2) each 2.00 284.75 569.50 A
TOTAL 3877.86 W
Add 1 % Water charges on "W-A" 33.08
TOTAL 3910.94 X
Add GST on "X-A" (multiplying
factor 0.1405) 469.47
TOTAL 4380.42 Y
Add 15% CPOH on "Y-A" 571.64
TOTAL 4952.05 Z
Add Cess @ 1% on "Z-A" 43.83
Cost of 1 water meter 4995.88
Say 4995.90
18.60.3 150 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no. water meter
MATERIAL
7420 Water meter (including testing charges)
150 mm each 1.00 4765.00 4765.00
9977 Carriage of water meter L.S. 39.00 2.12 82.68
9999 Labour for laying water meter L.S. 65.00 2.12 137.80
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.4 (Rate as per item No.18.30.4 Of
SH: Water Supply) each 2.00 343.55 687.10 A
TOTAL 5672.58 W
Add 1 % Water charges on "W-A" 49.85
TOTAL 5722.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 707.46
TOTAL 6429.90 Y
Add 15% CPOH on "Y-A" 861.42
TOTAL 7291.32 Z
Add Cess @ 1% on "Z-A" 66.04
Cost of 1 water meter 7357.36
Say 7357.35
SUB HEAD : 18- WATER SUPPLY 1609
18.60.4 200 mm dia nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no. water meter
MATERIAL
7421 Water meter (including testing charges)
200 mm each 1.00 5145.00 5145.00
9977 Carriage of water meter L.S. 52.00 2.12 110.24
9999 Labour for laying water meter L.S. 104.00 2.12 220.48
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.5 (Rate as per item no 20.47.5 of
SH : Water Supply) each 2.00 377.00 754.00 A
TOTAL 6229.72 W
Add 1 % Water charges on "W-A" 54.76
TOTAL 6284.48 X
Add GST on "X-A" (multiplying
factor 0.1405) 777.03
TOTAL 7061.51 Y
Add 15% CPOH on "Y-A" 946.13
TOTAL 8007.64 Z
Add Cess @ 1% on "Z-A" 72.54
Cost of 1 water meter 8080.17
Say 8080.15
18.61 Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts,
bolts, rubber insertions etc. complete conforming to IS : 2373 :
18.61.1 80 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for on no. dirt box strainer
MATERIAL
7422 Dirt box srainer 80 mm each 1.00 2680.00 2680.00
9977 Carriage of dirt box strainer L.S. 26.00 2.12 55.12
9999 Labour for laying dirt box strainer L.S. 39.00 2.12 82.68
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.1 (Rate as per item no 18.30.1 of
SH : Water Supply) each 2.00 182.85 365.70 A
TOTAL 3183.50 W
Add 1 % Water charges on "W-A" 28.18
TOTAL 3211.68 X
Add GST on "X-A" (multiplying
factor 0.1405) 399.86
TOTAL 3611.54 Y
Add 15% CPOH on "Y-A" 486.88
TOTAL 4098.41 Z
Add Cess @ 1% on "Z-A" 37.33
Cost of 1 dirt box stainer 4135.74
Say 4135.75
SUB HEAD : 18- WATER SUPPLY 1610
18.61.2 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 no. dirt box stainer
MATERIAL
7423 Dirt box srainer 100 mm each 1.00 4370.00 4370.00
9977 Carriage of dirt box strainer L.S. 26.00 2.12 55.12
9999 Labour for laying dirt box strainer L.S. 52.00 2.12 110.24
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.2 (Rate as per item No.18.30.2 Of
SH:Water Supply) each 2.00 284.75 569.50 A
TOTAL 5104.86 W
Add 1 % Water charges on "W-A" 45.35
TOTAL 5150.21 X
Add GST on "X-A" (multiplying
factor 0.1405) 643.59
TOTAL 5793.80 Y
Add 15% CPOH on "Y-A" 783.65
TOTAL 6577.45 Z
Add Cess @ 1% on "Z-A" 60.08
Cost of 1 dirt box stainer 6637.53
Say 6637.55
18.61.3 150 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 no. dirt box stainer
MATERIAL
7424 Dirt box srainer 150 mm each 1.00 5540.00 5540.00
9977 Carriage of dirt box strainer L.S. 39.00 2.12 82.68
9999 Labour for laying dirt box strainer L.S. 65.00 2.12 137.80
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.4 (Rate as per item No.18.30.4 Of
SH:Water Supply) each 2.00 343.55 687.10 A
TOTAL 6447.58 W
Add 1 % Water charges on "W-A" 57.60
TOTAL 6505.18 X
Add GST on "X-A" (multiplying
factor 0.1405) 817.44
TOTAL 7322.63 Y
Add 15% CPOH on "Y-A" 995.33
TOTAL 8317.95 Z
Add Cess @ 1% on "Z-A" 76.31
Cost for 1 dirt box stainer 8394.26
Say 8394.25
SUB HEAD : 18- WATER SUPPLY 1611
18.61.4 200 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for one no. dirt box
stainer
MATERIAL
7425 Dirt box srainer 200 mm each 1.00 7860.00 7860.00
9977 Carriage of dirt box strainer L.S. 52.00 2.12 110.24
9999 Labour for laying dirt box strainer L.S. 104.00 2.12 220.48
Providing flanged joints to double
acting air valves with bolts, nuts and
rubber insertions etc.
18.30.5 (Rate as per item no 20.47.5 of
SH : Water Supply) each 2.00 377.00 754.00 A
TOTAL 8944.72 W
Add 1 % Water charges on "W-A" 81.91
TOTAL 9026.63 X
Add GST on "X-A" (multiplying
factor 0.1405) 1162.30
TOTAL 10188.93 Y
Add 15% CPOH on "Y-A" 1415.24
TOTAL 11604.17 Z
Add Cess @ 1% on "Z-A" 108.50
Cost for 10 dirt box stainer 11712.67
Say 11712.65
18.62 Providing and fixing PTMT Ball cock of approved quality, colour and make
complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.
18.62.1 15 mm nominal bore, 105 mm long, weighing not less than 138 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7495 PTMT Ball Cock 15mm Complete with
Epoxy Coated Aluminium Road & H.D.
Ball each 1.00 75.00 75.00
9988 Carriage of materials and fixing charges L.S. 21.58 2.12 45.75
TOTAL 120.75 W
Add 1 % Water charges on "W" 1.21
TOTAL 121.96 X
Add GST on "X" (multiplying
factor 0.1405) 17.13
TOTAL 139.09 Y
Add 15% CPOH on "Y" 20.86
TOTAL 159.96 Z
Add Cess @ 1% on "Z" 1.60
Cost of one no. 161.56
Say 161.55
SUB HEAD : 18- WATER SUPPLY 1612
18.62.2 20 mm nominal bore, 120 mm long, weighing not less than 198 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7496 PTMT Ball Cock 20mm Complete with
Epoxy Coated Aluminium Road & H.D.
Ball each 1.00 110.00 110.00
9988 Carriage of materials and fixing charges L.S. 26.91 2.12 57.05
TOTAL 167.05 W
Add 1 % Water charges on "W" 1.67
TOTAL 168.72 X
Add GST on "X" (multiplying
factor 0.1405) 23.71
TOTAL 192.42 Y
Add 15% CPOH on "Y" 28.86
TOTAL 221.29 Z
Add Cess @ 1% on "Z" 2.21
Cost of one no. 223.50
Say 223.50
18.62.3 25 mm nominal bore, 152mm long, weighing not less than 440 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7497 PTMT Ball Cock 25mm Complete with
Epoxy Coated Aluminium Road & H.D.
Ball each 1.00 275.00 275.00
9988 Carriage of materials and fixing charges L.S. 32.24 2.12 68.35
TOTAL 343.35 W
Add 1 % Water charges on "W" 3.43
TOTAL 346.78 X
Add GST on "X" (multiplying
factor 0.1405) 48.72
TOTAL 395.51 Y
Add 15% CPOH on "Y" 59.33
TOTAL 454.83 Z
Add Cess @ 1% on "Z" 4.55
Cost of one no. 459.38
Say 459.40
18.62.4 40 mm nominal bore, 206mm long, weighing not less than 690 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7498 PTMT Ball Cock 40mm Complete with
Epoxy Coated Aluminium Road & H.D.
Ball each 1.00 420.00 420.00
SUB HEAD : 18- WATER SUPPLY 1613
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 32.24 2.12 68.35
TOTAL 488.35 W
Add 1 % Water charges on "W" 4.88
TOTAL 493.23 X
Add GST on "X" (multiplying
factor 0.1405) 69.30
TOTAL 562.53 Y
Add 15% CPOH on "Y" 84.38
TOTAL 646.91 Z
Add Cess @ 1% on "Z" 6.47
Cost of one no. 653.38
Say 653.40
18.62.5 50 mm nominal bore, 242mm long, weighing not less than 1240 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7499 PTMT Ball Cock 50mm Complete with
Epoxy Coated Aluminium Road & H.D.
Ball each 1.00 820.00 820.00
9988 Carriage of materials and fixing charges L.S. 32.24 2.12 68.35
TOTAL 888.35 W
Add 1 % Water charges on "W" 8.88
TOTAL 897.23 X
Add GST on "X" (multiplying
factor 0.1405) 126.06
TOTAL 1023.29 Y
Add 15% CPOH on "Y" 153.49
TOTAL 1176.79 Z
Add Cess @ 1% on "Z" 11.77
Cost of one no. 1188.56
Say 1188.55
18.63 Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not
less than 85 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7500 PTMT Angle Stop cock with Flenge
15mm each 1.00 85.00 85.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 102.09 W
Add 1 % Water charges on "W" 1.02
TOTAL 103.11 X
Add GST on "X" (multiplying
factor 0.1405) 14.49
TOTAL 117.59 Y
Add 15% CPOH on "Y" 17.64
TOTAL 135.23 Z
Add Cess @ 1% on "Z" 1.35
Cost of one no. 136.59
Say 136.60
SUB HEAD : 18- WATER SUPPLY 1614
18.64 Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing
not less than 40 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7501 PTMT Swiveling shower 15mm each 1.00 65.00 65.00
9988 Carriage of materials and fixing charges L.S. 6.76 2.12 14.33
TOTAL 79.33 W
Add 1 % Water charges on "W" 0.79
TOTAL 80.12 X
Add GST on "X" (multiplying
factor 0.1405) 11.26
TOTAL 91.38 Y
Add 15% CPOH on "Y" 13.71
TOTAL 105.09 Z
Add Cess @ 1% on "Z" 1.05
Cost of one no. 106.14
Say 106.15
18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth
102mm, height of 75mm with concealed fitting arrangements, weighing not less
than 106 gms.
Code Description Unit Quantity Rate Amount
Details of cost for one no
MATERIAL
7509 PTMT Soap Dish/Holder 138x102x75mm each 1.00 58.00 58.00
9988 Carriage of materials and fixing charges L.S. 6.76 2.12 14.33
TOTAL 72.33 W
Add 1 % Water charges on "W" 0.72
TOTAL 73.05 X
Add GST on "X" (multiplying
factor 0.1405) 10.26
TOTAL 83.32 Y
Add 15% CPOH on "Y" 12.50
TOTAL 95.82 Z
Add Cess @ 1% on "Z" 0.96
Cost of one no 96.77
Say 96.75
18.66 Providing and laying S&S C.I. Standard specials such as tees, bends, collars
tapers and caps etc, suitable for flanged jointing as per IS : 1538 :
18.66.1 Up to 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7708 S&S Centrifugally (Spun) C.I. Pipe
Specials as per IS 1538 suitable for
lead jointing upto 300mm dia quintal 1.00 5190.00 5190.00
SUB HEAD : 18- WATER SUPPLY 1615
Code Description Unit Quantity Rate Amount
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 5750.57 W
Add 1 % Water charges on "W-A" 52.05
TOTAL 5802.62 X
Add GST on "X-A" (multiplying
factor 0.1405) 738.55
TOTAL 6541.17 Y
Add 15% CPOH on "Y-A" 899.28
TOTAL 7440.45 Z
Add Cess @ 1% on "Z-A" 68.94
Cost of 1 quintal 7509.39
Say 7509.40
18.66.2 Above 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7709 S&S Centrifugally (Spun) C.I. Pipe
Specials as per IS 1538 suitable for
lead jointing over 300mm dia quintal 1.00 6200.00 6200.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 6760.57 W
Add 1 % Water charges on "W-A" 62.15
TOTAL 6822.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 881.88
TOTAL 7704.60 Y
Add 15% CPOH on "Y-A" 1073.79
TOTAL 8778.39 Z
Add Cess @ 1% on "Z-A" 82.32
Cost of 1 quintal 8860.71
Say 8860.70
18.67 Providing and laying S&S C.I. Standard specials suitable for mechanical jointing
as per IS : 13382 :
18.67.1 Up to 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7710 S&S Centrifugally (Spun) C.I. Pipe
specials suitable for mechanical joint
as per I.S. 13382 upto 300mm dia quintal 1.00 8571.00 8571.00
SUB HEAD : 18- WATER SUPPLY 1616
Code Description Unit Quantity Rate Amount
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 9131.57 W
Add 1 % Water charges on "W-A" 85.86
TOTAL 9217.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 1218.34
TOTAL 10435.76 Y
Add 15% CPOH on "Y-A" 1483.46
TOTAL 11919.23 Z
Add Cess @ 1% on "Z-A" 113.73
Cost of 1 quintal 12032.96
Say 12032.95
18.67.2 Above 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7711 S&S Centrifugally (Spun) C.I. Pipe
Specials suitabe for mechanical joint
as per IS 13382 over 300mm dia quintal 1.00 9048.00 9048.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for Laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 9608.57 W
Add 1 % Water charges on "W-A" 90.63
TOTAL 9699.20 X
Add GST on "X-A" (multiplying
factor 0.1405) 1286.02
TOTAL 10985.22 Y
Add 15% CPOH on "Y-A" 1565.88
TOTAL 12551.11 Z
Add Cess @ 1% on "Z-A" 120.05
Cost of 1 quintal 12671.16
Say 12671.15
18.68 Providing and laying D.I. specials of class K-12 suitable for push-on jointing as
per IS : 9523 :
18.68.1 Up to 600 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7682 Ductile Iron K - 12 specials suitable for
push on jointing upto 600 mm dia quintal 1.00 12400.00 12400.00
SUB HEAD : 18- WATER SUPPLY 1617
Code Description Unit Quantity Rate Amount
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 12960.57 W
Add 1 % Water charges on "W-A" 124.15
TOTAL 13084.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 1761.69
TOTAL 14846.41 Y
Add 15% CPOH on "Y-A" 2145.06
TOTAL 16991.47 Z
Add Cess @ 1% on "Z-A" 164.45
Cost of 1 quintal 17155.92
Say 17155.90
18.68.2 Above 600 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7683 Ductile Iron K - 12 specials suitable for
push on jointing over 600mm dia quintal 1.00 17200.00 17200.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 17760.57 W
Add 1 % Water charges on "W-A" 172.15
TOTAL 17932.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 2442.83
TOTAL 20375.55 Y
Add 15% CPOH on "Y-A" 2974.43
TOTAL 23349.98 Z
Add Cess @ 1% on "Z-A" 228.04
Cost of 1 quintal 23578.02
Say 23578.00
18.69 Providing and laying D.I. Specials of Class K - 12 suitable for mechanical jointing
as per IS : 9523 :
18.69.1 Up to 600 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7684 Ductile Iron specials suitable for
mechanical jointing as per I.S. 9523 -
upto 600mm dia quintal 1.00 13050.00 13050.00
SUB HEAD : 18- WATER SUPPLY 1618
Code Description Unit Quantity Rate Amount
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 13610.57 W
Add 1 % Water charges on "W-A" 130.65
TOTAL 13741.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 1853.93
TOTAL 15595.15 Y
Add 15% CPOH on "Y-A" 2257.37
TOTAL 17852.52 Z
Add Cess @ 1% on "Z-A" 173.07
Cost of 1 quintal 18025.58
Say 18025.60
18.69.2 Above 600 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 quintal
MATERIAL
7685 Ductile Iron Specials suitable for
mechancial jointing as per I.S. 9523
over 600mm dia quintal 1.00 18750.00 18750.00
2309 Carriage of Cast iron fittings tonne 0.10 145.72 14.57
Labour for laying
18.24 Rate as per Item Number 18.24 of
SH: Water Supply quintal 1.00 546.00 546.00 A
TOTAL 19310.57 W
Add 1 % Water charges on "W-A" 187.65
TOTAL 19498.22 X
Add GST on "X-A" (multiplying
factor 0.1405) 2662.79
TOTAL 22161.00 Y
Add 15% CPOH on "Y-A" 3242.25
TOTAL 25403.25 Z
Add Cess @ 1% on "Z-A" 248.57
Cost of 1 quintal 25651.83
Say 25651.85
18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron
Pipes including testing of joints and the cost of rubber gasket :
18.70.1 100 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7666 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 100mm dia each 50.00 29.00 1450.00
Labour
0116 Fitter (grade 1) day 1.00 784.00 784.00
SUB HEAD : 18- WATER SUPPLY 1619
Code Description Unit Quantity Rate Amount
0117 Assistant Fitter or 2nd class Fitter day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 3593.00 W
Add 1 % Water charges on "W" 35.93
TOTAL 3628.93 X
Add GST on "X" (multiplying
factor 0.1405) 509.86
TOTAL 4138.79 Y
Add 15% CPOH on "Y" 620.82
TOTAL 4759.61 Z
Add Cess @ 1% on "Z" 47.60
Cost of 50 joints 4807.21
Cost of 1 joint 96.14
Say 96.15
18.70.2 150 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7668 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 150mm dia each 50.00 33.00 1650.00
Labour
0116 Fitter (grade 1) day 1.50 784.00 1176.00
0117 Assistant Fitter or 2nd class Fitter day 1.50 714.00 1071.00
0114 Beldar day 3.00 645.00 1935.00
TOTAL 5832.00 W
Add 1 % Water charges on "W" 58.32
TOTAL 5890.32 X
Add GST on "X" (multiplying
factor 0.1405) 827.59
TOTAL 6717.91 Y
Add 15% CPOH on "Y" 1007.69
TOTAL 7725.60 Z
Add Cess @ 1% on "Z" 77.26
Cost of 50 joints 7802.85
Cost of 1 joint 156.06
Say 156.05
18.70.3 200 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7669 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 200mm dia each 50.00 60.00 3000.00
LABOUR
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0117 Assistant Fitter or 2nd class Fitter day 2.00 714.00 1428.00
SUB HEAD : 18- WATER SUPPLY 1620
Code Description Unit Quantity Rate Amount
0114 Beldar day 4.00 645.00 2580.00
TOTAL 8576.00 W
Add 1 % Water charges on "W" 85.76
TOTAL 8661.76 X
Add GST on "X" (multiplying
factor 0.1405) 1216.98
TOTAL 9878.74 Y
Add 15% CPOH on "Y" 1481.81
TOTAL 11360.55 Z
Add Cess @ 1% on "Z" 113.61
Cost of 50 joints 11474.15
Cost of 1 joint 229.48
Say 229.50
18.70.4 250 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7670 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 250mm dia each 50.00 70.00 3500.00
LABOUR
0116 Fitter (grade 1) day 2.50 784.00 1960.00
0117 Assistant Fitter or 2nd class Fitter day 2.50 714.00 1785.00
0114 Beldar day 5.00 645.00 3225.00
TOTAL 10470.00 W
Add 1 % Water charges on "W" 104.70
TOTAL 10574.70 X
Add GST on "X" (multiplying
factor 0.1405) 1485.75
TOTAL 12060.45 Y
Add 15% CPOH on "Y" 1809.07
TOTAL 13869.51 Z
Add Cess @ 1% on "Z" 138.70
Cost of 50 joints 14008.21
Cost of 1 joint 280.16
Say 280.15
18.70.5 300 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7671 Ruber Gaskets Conforming to
I.S 5382 of S.B.R quality 300mm dia each 50.00 100.00 5000.00
LABOUR
0116 Fitter (grade 1) day 3.00 784.00 2352.00
0117 Assistant Fitter or 2nd class Fitter day 3.00 714.00 2142.00
SUB HEAD : 18- WATER SUPPLY 1621
Code Description Unit Quantity Rate Amount
0114 Beldar day 6.00 645.00 3870.00
TOTAL 13364.00 W
Add 1 % Water charges on "W" 133.64
TOTAL 13497.64 X
Add GST on "X" (multiplying
factor 0.1405) 1896.42
TOTAL 15394.06 Y
Add 15% CPOH on "Y" 2309.11
TOTAL 17703.17 Z
Add Cess @ 1% on "Z" 177.03
Cost of 50 joints 17880.20
Cost of 1 joint 357.60
Say 357.60
18.70.6 350 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7672 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 350mm dia each 50.00 116.00 5800.00
LABOUR
0116 Fitter (grade 1) day 3.50 784.00 2744.00
0117 Assistant Fitter or 2nd class Fitter day 3.50 714.00 2499.00
0114 Beldar day 7.00 645.00 4515.00
TOTAL 15558.00 W
Add 1 % Water charges on "W" 155.58
TOTAL 15713.58 X
Add GST on "X" (multiplying
factor 0.1405) 2207.76
TOTAL 17921.34 Y
Add 15% CPOH on "Y" 2688.20
TOTAL 20609.54 Z
Add Cess @ 1% on "Z" 206.10
Cost of 50 joints 20815.63
Cost of 1 joint 416.31
Say 416.30
18.70.7 400 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7673 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 400mm dia each 50.00 210.00 10500.00
LABOUR
0116 Fitter (grade 1) day 4.00 784.00 3136.00
0117 Assistant Fitter or 2nd class Fitter day 4.00 714.00 2856.00
SUB HEAD : 18- WATER SUPPLY 1622
Code Description Unit Quantity Rate Amount
0114 Beldar day 8.00 645.00 5160.00
TOTAL 21652.00 W
Add 1 % Water charges on "W" 216.52
TOTAL 21868.52 X
Add GST on "X" (multiplying
factor 0.1405) 3072.53
TOTAL 24941.05 Y
Add 15% CPOH on "Y" 3741.16
TOTAL 28682.20 Z
Add Cess @ 1% on "Z" 286.82
Cost of 50 joints 28969.03
Cost of 1 joint 579.38
Say 579.40
18.70.8 450 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7674 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 450mm dia each 50.00 250.00 12500.00
LABOUR
0116 Fitter (grade 1) day 4.50 784.00 3528.00
0117 Assistant Fitter or 2nd class Fitter day 4.50 714.00 3213.00
0114 Beldar day 9.00 645.00 5805.00
TOTAL 25046.00 W
Add 1 % Water charges on "W" 250.46
TOTAL 25296.46 X
Add GST on "X" (multiplying
factor 0.1405) 3554.15
TOTAL 28850.61 Y
Add 15% CPOH on "Y" 4327.59
TOTAL 33178.20 Z
Add Cess @ 1% on "Z" 331.78
Cost of 50 joints 33509.99
Cost of 1 joint 670.20
Say 670.20
18.70.9 500 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7675 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 500mm dia each 50.00 270.00 13500.00
LABOUR
0116 Fitter (grade 1) day 4.75 784.00 3724.00
0117 Assistant Fitter or 2nd class Fitter day 4.75 714.00 3391.50
SUB HEAD : 18- WATER SUPPLY 1623
Code Description Unit Quantity Rate Amount
0114 Beldar day 9.50 645.00 6127.50
TOTAL 26743.00 W
Add 1 % Water charges on "W" 267.43
TOTAL 27010.43 X
Add GST on "X" (multiplying
factor 0.1405) 3794.97
TOTAL 30805.40 Y
Add 15% CPOH on "Y" 4620.81
TOTAL 35426.20 Z
Add Cess @ 1% on "Z" 354.26
Cost of 50 joints 35780.47
Cost of 1 joint 715.61
Say 715.60
18.70.10 600 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7676 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 600mm dia each 50.00 356.00 17800.00
LABOUR
0116 Fitter (grade 1) day 6.50 784.00 5096.00
0117 Assistant Fitter or 2nd class Fitter day 6.50 714.00 4641.00
0114 Beldar day 13.00 645.00 8385.00
TOTAL 35922.00 W
Add 1 % Water charges on "W" 359.22
TOTAL 36281.22 X
Add GST on "X" (multiplying
factor 0.1405) 5097.51
TOTAL 41378.73 Y
Add 15% CPOH on "Y" 6206.81
TOTAL 47585.54 Z
Add Cess @ 1% on "Z" 475.86
Cost of 50 joints 48061.40
Cost of 1 joint 961.23
Say 961.25
18.70.11 700 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7677 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 700mm dia each 50.00 510.00 25500.00
LABOUR
0116 Fitter (grade 1) day 7.70 784.00 6036.80
0117 Assistant Fitter or 2nd class Fitter day 7.70 714.00 5497.80
SUB HEAD : 18- WATER SUPPLY 1624
Code Description Unit Quantity Rate Amount
0114 Beldar day 15.40 645.00 9933.00
TOTAL 46967.60 W
Add 1 % Water charges on "W" 469.68
TOTAL 47437.28 X
Add GST on "X" (multiplying
factor 0.1405) 6664.94
TOTAL 54102.21 Y
Add 15% CPOH on "Y" 8115.33
TOTAL 62217.55 Z
Add Cess @ 1% on "Z" 622.18
Cost of 50 joints 62839.72
Cost of 1 joint 1256.79
Say 1256.80
18.70.12 750 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7678 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 750mm dia each 50.00 600.00 30000.00
LABOUR
0116 Fitter (grade 1) day 7.70 784.00 6036.80
0117 Assistant Fitter or 2nd class Fitter day 7.70 714.00 5497.80
0114 Beldar day 15.40 645.00 9933.00
TOTAL 51467.60 W
Add 1 % Water charges on "W" 514.68
TOTAL 51982.28 X
Add GST on "X" (multiplying
factor 0.1405) 7303.51
TOTAL 59285.79 Y
Add 15% CPOH on "Y" 8892.87
TOTAL 68178.65 Z
Add Cess @ 1% on "Z" 681.79
Cost of 50 joints 68860.44
Cost of 1 joint 1377.21
Say 1377.20
18.70.13 800 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7679 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 800mm dia each 50.00 705.00 35250.00
LABOUR
0116 Fitter (grade 1) day 8.50 784.00 6664.00
0117 Assistant Fitter or 2nd class Fitter day 8.50 714.00 6069.00
SUB HEAD : 18- WATER SUPPLY 1625
Code Description Unit Quantity Rate Amount
0114 Beldar day 17.00 645.00 10965.00
TOTAL 58948.00 W
Add 1 % Water charges on "W" 589.48
TOTAL 59537.48 X
Add GST on "X" (multiplying
factor 0.1405) 8365.02
TOTAL 67902.50 Y
Add 15% CPOH on "Y" 10185.37
TOTAL 78087.87 Z
Add Cess @ 1% on "Z" 780.88
Cost of 50 joints 78868.75
Cost of 1 joint 1577.37
Say 1577.35
18.70.14 900 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7680 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 900mm dia each 50.00 910.00 45500.00
LABOUR
0116 Fitter (grade 1) day 10.00 784.00 7840.00
0117 Assistant Fitter or 2nd class Fitter day 10.00 714.00 7140.00
0114 Beldar day 20.00 645.00 12900.00
TOTAL 73380.00 W
Add 1 % Water charges on "W" 733.80
TOTAL 74113.80 X
Add GST on "X" (multiplying
factor 0.1405) 10412.99
TOTAL 84526.79 Y
Add 15% CPOH on "Y" 12679.02
TOTAL 97205.81 Z
Add Cess @ 1% on "Z" 972.06
Cost of 50 joints 98177.87
Cost of 1 joint 1963.56
Say 1963.55
18.70.15 1000 mm dia pipes
Code Description Unit Quantity Rate Amount
Details of cost for 50 Joints
MATERIAL
7681 Ruber Gaskets Conforming to I.S 5382
of S.B.R quality 1000mm dia each 50.00 1080.00 54000.00
LABOUR
0116 Fitter (grade 1) day 11.00 784.00 8624.00
0117 Assistant Fitter or 2nd class Fitter day 11.00 714.00 7854.00
SUB HEAD : 18- WATER SUPPLY 1626
Code Description Unit Quantity Rate Amount
0114 Beldar day 22.00 645.00 14190.00
TOTAL 84668.00 W
Add 1 % Water charges on "W" 846.68
TOTAL 85514.68 X
Add GST on "X" (multiplying
factor 0.1405) 12014.81
TOTAL 97529.49 Y
Add 15% CPOH on "Y" 14629.42
TOTAL 112158.92 Z
Add Cess @ 1% on "Z" 1121.59
Cost of 50 joints 113280.51
Cost of 1 joint 2265.61
Say 2265.60
18.71 Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun)
Cast Iron, Class B (IS : 1536) :
18.71.1 100 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
100 mm dia. cast iron pipes double
flanged = 27.00 Kg
Weight of 5 m pipes 27.00x5
= 135.00 Kg
7712 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 100mm dia metre 5.00 1310.00 6550.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.05 358.32 17.92
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 1.35 298.50 402.98 A
TOTAL 6970.89 W
Add 1 % Water charges on "W-A" 65.68
TOTAL 7036.57 X
Add GST on "X-A" (multiplying
factor 0.1405) 932.02
TOTAL 7968.59 Y
Add 15% CPOH on "Y-A" 1134.84
TOTAL 9103.43 Z
Add Cess @ 1% on "Z-A" 87.00
Cost of 5 metre 9190.44
Cost of metre 1838.09
Say 1838.10
SUB HEAD : 18- WATER SUPPLY 1627
18.71.2 150 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
150 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 44.10 Kg
Weight of 5 m pipes = 44.10x5
= 220.50 Kg
7713 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 150mm dia metre 5.00 2048.00 10240.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.05 597.20 29.86
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 2.21 298.50 659.69 A
TOTAL 10929.55 W
Add 1 % Water charges on "W-A" 102.70
TOTAL 11032.24 X
Add GST on "X-A" (multiplying
factor 0.1405) 1457.34
TOTAL 12489.59 Y
Add 15% CPOH on "Y-A" 1774.49
TOTAL 14264.07 Z
Add Cess @ 1% on "Z-A" 136.04
Cost of 5 metre 14400.12
Cost per metre 2880.02
Say 2880.00
18.71.3 200 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
200 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 63.50 Kg
Weight of 5 m pipes 63.50x5
= 317.50 Kg
7714 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 200mm dia metre 5.00 3238.00 16190.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.05 971.45 48.57
Labour for laying
SUB HEAD : 18- WATER SUPPLY 1628
Code Description Unit Quantity Rate Amount
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 3.18 298.50 949.23 A
TOTAL 17187.80 W
Add 1 % Water charges on "W-A" 162.39
TOTAL 17350.19 X
Add GST on "X-A" (multiplying
factor 0.1405) 2304.33
TOTAL 19654.52 Y
Add 15% CPOH on "Y-A" 2805.79
TOTAL 22460.32 Z
Add Cess @ 1% on "Z-A" 215.11
Cost of 5 metre 22675.43
Cost per metre 4535.09
Say 4535.10
18.71.4 250 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
250 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 85.30 Kg
Weight of 5 m pipes 85.30x5
= 426.50 Kg
7715 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 250mm dia metre 5.00 3905.00 19525.00
2323 Carriage of Spun iron S & S pipes
250 mm dia 100 metre 0.05 1380.48 69.02
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 4.27 298.50 1274.60 A
TOTAL 20868.62 W
Add 1 % Water charges on "W-A" 195.94
TOTAL 21064.56 X
Add GST on "X-A" (multiplying
factor 0.1405) 2780.49
TOTAL 23845.05 Y
Add 15% CPOH on "Y-A" 3385.57
TOTAL 27230.62 Z
Add Cess @ 1% on "Z-A" 259.56
Cost of 5 metre 27490.18
Cost per metre 5498.04
Say 5498.05
SUB HEAD : 18- WATER SUPPLY 1629
18.71.5 300 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
300 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 110.00 Kg
Weight of 5 m pipes 110.00x5
= 550.00 Kg
7716 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 300mm dia metre 5.00 4990.00 24950.00
2324 Carriage of Spun iron S & S pipes
300 mm dia 100 metre 0.05 1706.30 85.32
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 5.50 298.50 1641.75 A
TOTAL 26677.07 W
Add 1 % Water charges on "W-A" 250.35
TOTAL 26927.42 X
Add GST on "X-A" (multiplying
factor 0.1405) 3552.64
TOTAL 30480.05 Y
Add 15% CPOH on "Y-A" 4325.75
TOTAL 34805.80 Z
Add Cess @ 1% on "Z-A" 331.64
Cost of 5 metre 35137.44
Cost per metre 7027.49
Say 7027.50
18.71.6 350 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
350 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 135.70 Kg
Weight of 5 m pipes 135.70x5
= 678.50 Kg
7717 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 350mm dia metre 5.00 6286.00 31430.00
2325 Carriage of Spun iron S & S pipes
350 mm dia 100 metre 0.05 2388.82 119.44
Labour for laying
SUB HEAD : 18- WATER SUPPLY 1630
Code Description Unit Quantity Rate Amount
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 6.79 298.50 2026.82 A
TOTAL 33576.26 W
Add 1 % Water charges on "W-A" 315.49
TOTAL 33891.75 X
Add GST on "X-A" (multiplying
factor 0.1405) 4477.02
TOTAL 38368.77 Y
Add 15% CPOH on "Y-A" 5451.29
TOTAL 43820.07 Z
Add Cess @ 1% on "Z-A" 417.93
Cost of 5 metre 44238.00
Cost per metre 8847.60
Say 8847.60
18.71.7 400 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
400 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 166.80 Kg
Weight of 5 m pipes 166.80x5
= 834.00 Kg
7718 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 400mm dia metre 5.00 8143.00 40715.00
2326 Carriage of Spun iron S & S pipes
400 mm dia 100 metre 0.05 3257.48 162.87
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 8.34 298.50 2489.49 A
TOTAL 43367.36 W
Add 1 % Water charges on "W-A" 408.78
TOTAL 43776.14 X
Add GST on "X-A" (multiplying
factor 0.1405) 5800.77
TOTAL 49576.92 Y
Add 15% CPOH on "Y-A" 7063.11
TOTAL 56640.03 Z
Add Cess @ 1% on "Z-A" 541.51
Cost of 5 metre 57181.54
Cost per metre 11436.31
Say 11436.30
SUB HEAD : 18- WATER SUPPLY 1631
18.71.8 450 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
450 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 201.60 Kg
Weight of 5 m pipes 201.60x5
= 1008.00 Kg
7719 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 450mm dia metre 5.00 10381.00 51905.00
2327 Carriage of Spun iron S & S pipes
450 mm dia 100 metre 0.05 3981.36 199.07
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 10.08 298.50 3008.88 A
TOTAL 55112.95 W
Add 1 % Water charges on "W-A" 521.04
TOTAL 55633.99 X
Add GST on "X-A" (multiplying
factor 0.1405) 7393.83
TOTAL 63027.82 Y
Add 15% CPOH on "Y-A" 9002.84
TOTAL 72030.66 Z
Add Cess @ 1% on "Z-A" 690.22
Cost of 5 metre 72720.87
Cost per metre 14544.17
Say 14544.15
18.71.9 500 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
500 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 234.80 Kg
Weight of 5 m pipes 234.80x5
= 1174.00 Kg
7720 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 500mm dia metre 5.00 12914.00 64570.00
2328 Carriage of Spun iron S & S pipes
500 mm dia 100 metre 0.05 3981.36 199.07
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 11.74 298.50 3504.39 A
TOTAL 68273.46 W
Add 1 % Water charges on "W-A" 647.69
TOTAL 68921.15 X
Add GST on "X-A" (multiplying
factor 0.1405) 9191.05
TOTAL 78112.20 Y
Add 15% CPOH on "Y-A" 11191.17
TOTAL 89303.38 Z
Add Cess @ 1% on "Z-A" 857.99
Cost of 5 metre 90161.37
Cost per metre 18032.27
Say 18032.25
SUB HEAD : 18- WATER SUPPLY 1632
18.71.10 600 mm dia C.I. Double Flanged Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
600 mm dia. cast iron pipes double
flanged
Weight of 1 m pipes = 315.30 Kg
Weight of 5 m pipes 315.30x5
= 1576.50 Kg
7721 Screwed double flanged centrigually
cast (spun) C.I. Pipe of Class B
conforming to I.S. 1536, - 600mm dia metre 5.00 17905.00 89525.00
2329 Carriage of Spun iron S & S pipes
600mm dia 100 metre 0.05 5972.04 298.60
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 15.77 298.50 4707.35 A
TOTAL 94530.95 W
Add 1 % Water charges on "W-A" 898.24
TOTAL 95429.18 X
Add GST on "X-A" (multiplying
factor 0.1405) 12746.42
TOTAL 108175.60 Y
Add 15% CPOH on "Y-A" 15520.24
TOTAL 123695.84 Z
Add Cess @ 1% on "Z-A" 1189.88
Cost of 5 metre 124885.72
Cost per metre 24977.14
Say 24977.15
18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes
conforming to IS : 8329 :
18.72.1 100 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
100mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 15.39 Kg
Weight of 10m pipes 15.39x10 =
153.90 Kg
7722 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 100mm dia metre 10.00 800.00 8000.00
2343 Carriage of ductile iron pipes (k7)
100 mm dia 100 metre 0.10 358.32 35.83
SUB HEAD : 18- WATER SUPPLY 1633
Code Description Unit Quantity Rate Amount
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 1.54 298.50 459.69 A
TOTAL 8495.52 W
Add 1 % Water charges on "W-A" 80.36
TOTAL 8575.88 X
Add GST on "X-A" (multiplying
factor 0.1405) 1140.32
TOTAL 9716.21 Y
Add 15% CPOH on "Y-A" 1388.48
TOTAL 11104.68 Z
Add Cess @ 1% on "Z-A" 106.45
Cost of 10 metre 11211.13
Cost per metre 1121.11
Say 1121.10
18.72.2 150 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
150 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 22.750 Kg
Weight of 10m pipes 22.750x10
= 227.50 Kg
7723 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 150mm dia metre 10.00 1140.00 11400.00
2344 Carriage of cast iron pipes 150 mm dia 100 metre 0.10 597.20 59.72
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 2.28 298.50 680.58 A
TOTAL 12140.30 W
Add 1 % Water charges on "W-A" 114.60
TOTAL 12254.90 X
Add GST on "X-A" (multiplying
factor 0.1405) 1626.19
TOTAL 13881.09 Y
Add 15% CPOH on "Y-A" 1980.08
TOTAL 15861.17 Z
Add Cess @ 1% on "Z-A" 151.81
Cost of 10 metre 16012.97
Cost per metre 1601.30
Say 1601.30
SUB HEAD : 18- WATER SUPPLY 1634
18.72.3 200 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
200 mm dia. cast iron pipes (in 5.5 m
lengths)
Weight of 1 m pipes = 30.090 Kg
Weight of 10m pipes 30.090x10
= 300.90 Kg
7724 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 200mm dia metre 10.00 1400.00 14000.00
2345 Carriage of cast iron pipes 200 mm dia 100 metre 0.10 971.45 97.15
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 3.01 298.50 898.49 A
TOTAL 14995.63 W
Add 1 % Water charges on "W-A" 140.97
TOTAL 15136.60 X
Add GST on "X-A" (multiplying
factor 0.1405) 2000.46
TOTAL 17137.06 Y
Add 15% CPOH on "Y-A" 2435.79
TOTAL 19572.84 Z
Add Cess @ 1% on "Z-A" 186.74
Cost of 10 metre 19759.59
Cost per metre 1975.96
Say 1975.95
18.72.4 250 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
250mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 39.310 Kg
Weight of 10m pipes 39.310x10
= 393.10 Kg
7725 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 250mm dia metre 10.00 1800.00 18000.00
2346 Carriage of cast iron pipes 250 mm dia 100 metre 0.10 1380.48 138.05
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 3.93 298.50 1173.11 A
TOTAL 19311.15 W
Add 1 % Water charges on "W-A" 181.38
TOTAL 19492.53 X
Add GST on "X-A" (multiplying
factor 0.1405) 2573.88
TOTAL 22066.41 Y
Add 15% CPOH on "Y-A" 3134.00
TOTAL 25200.41 Z
Add Cess @ 1% on "Z-A" 240.27
Cost of 10 metre 25440.68
Cost per metre 2544.07
Say 2544.05
SUB HEAD : 18- WATER SUPPLY 1635
18.72.5 300 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
300mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 48.400 Kg
Weight of 10m pipes 48.400x10
= 484.00 Kg
7726 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 300mm dia metre 10.00 2250.00 22500.00
2347 Carriage of cast iron pipes 300 mm dia 100 metre 0.10 1706.30 170.63
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 4.84 298.50 1444.74 A
TOTAL 24115.37 W
Add 1 % Water charges on "W-A" 226.71
TOTAL 24342.08 X
Add GST on "X-A" (multiplying
factor 0.1405) 3217.08
TOTAL 27559.15 Y
Add 15% CPOH on "Y-A" 3917.16
TOTAL 31476.31 Z
Add Cess @ 1% on "Z-A" 300.32
Cost of 10 metre 31776.63
Cost per metre 3177.66
Say 3177.65
18.72.6 350 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
350mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 66.020 Kg
Weight of 10m pipes 66.020x10
= 660.20 Kg
7727 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 350mm dia metre 10.00 2650.00 26500.00
2348 Carriage of cast iron pipes 350 mm dia 100 metre 0.10 2388.82 238.88
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 6.60 298.50 1970.10 A
TOTAL 28708.98 W
Add 1 % Water charges on "W-A" 267.39
TOTAL 28976.37 X
Add GST on "X-A" (multiplying
factor 0.1405) 3794.38
TOTAL 32770.75 Y
Add 15% CPOH on "Y-A" 4620.10
TOTAL 37390.85 Z
Add Cess @ 1% on "Z-A" 354.21
Cost of 10 metre 37745.06
Cost per metre 3774.51
Say 3774.50
SUB HEAD : 18- WATER SUPPLY 1636
18.72.7 400 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
400mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 78.280 Kg
Weight of 10m pipes 78.280x10
= 782.80 Kg
7728 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 400mm dia metre 10.00 3175.00 31750.00
2349 Carriage of cast iron pipes 400 mm dia 100 metre 0.10 3257.48 325.75
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 7.83 298.50 2337.26 A
TOTAL 34413.00 W
Add 1 % Water charges on "W-A" 320.76
TOTAL 34733.76 X
Add GST on "X-A" (multiplying
factor 0.1405) 4551.71
TOTAL 39285.47 Y
Add 15% CPOH on "Y-A" 5542.23
TOTAL 44827.70 Z
Add Cess @ 1% on "Z-A" 424.90
Cost of 10 metre 45252.61
Cost per metre 4525.26
Say 4525.25
18.72.8 450 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
450mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 91.410 Kg
Weight of 10m pipes 91.410x10
= 914.10 Kg
7729 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 450mm dia metre 10.00 3852.00 38520.00
2350 Carriage of cast iron pipes 450 mm dia 100 metre 0.10 3981.36 398.14
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 9.14 298.50 2728.29 A
TOTAL 41646.43 W
Add 1 % Water charges on "W-A" 389.18
TOTAL 42035.61 X
Add GST on "X-A" (multiplying
factor 0.1405) 5522.68
TOTAL 47558.29 Y
Add 15% CPOH on "Y-A" 6724.50
TOTAL 54282.78 Z
Add Cess @ 1% on "Z-A" 515.54
Cost of 10 metre 54798.33
Cost per metre 5479.83
Say 5479.85
SUB HEAD : 18- WATER SUPPLY 1637
18.72.9 500 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
500mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 106.640 Kg
Weight of 10m pipes 106.640x10
= 1066.40 Kg
7730 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 500mm dia metre 10.00 4350.00 43500.00
2351 Carriage of cast iron pipes 500 mm dia 100 metre 0.10 3981.36 398.14
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 10.66 298.50 3182.01 A
TOTAL 47080.15 W
Add 1 % Water charges on "W-A" 438.98
TOTAL 47519.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 6229.36
TOTAL 53748.49 Y
Add 15% CPOH on "Y-A" 7584.97
TOTAL 61333.46 Z
Add Cess @ 1% on "Z-A" 581.51
Cost of 10 metre 61914.98
Cost per metre 6191.50
Say 6191.50
18.72.10 600 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
600mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 138.61 Kg
Weight of 10m pipes 138.61x10
= 1386.10 Kg
7731 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 600mm dia metre 10.00 5600.00 56000.00
2352 Carriage of cast iron pipes 600 mm dia 100 metre 0.10 5972.04 597.20
Labour for laying
18.23 Rate same as per item no 18.23 of
SH: Water Supply quintal 13.86 298.50 4137.21 A
TOTAL 60734.41 W
Add 1 % Water charges on "W-A" 565.97
TOTAL 61300.39 X
Add GST on "X-A" (multiplying
factor 0.1405) 8031.43
TOTAL 69331.81 Y
Add 15% CPOH on "Y-A" 9779.19
TOTAL 79111.00 Z
Add Cess @ 1% on "Z-A" 749.74
Cost of 10 metre 79860.74
Cost per metre 7986.07
Say 7986.05
SUB HEAD : 18- WATER SUPPLY 1638
18.72.11 700 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
700mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 188.92 Kg
Weight of 10m pipes 188.92x10
= 1889.20 Kg
7732 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 700mm dia metre 10.00 7300.00 73000.00
2353 Carriage of cast iron pipes 700 mm dia 100 metre 0.10 5972.04 597.20
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 18.89 298.50 5638.67 A
TOTAL 79235.87 W
Add 1 % Water charges on "W-A" 735.97
TOTAL 79971.84 X
Add GST on "X-A" (multiplying
factor 0.1405) 10443.81
TOTAL 90415.65 Y
Add 15% CPOH on "Y-A" 12716.55
TOTAL 103132.20 Z
Add Cess @ 1% on "Z-A" 974.94
Cost of 10 metre 104107.14
Cost per metre 10410.71
Say 10410.70
18.72.12 800 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
800mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 243.51 Kg
Weight of 10m pipes 243.51x10
= 2435.10 Kg
7733 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 800mm dia metre 10.00 9100.00 91000.00
2355 Carriage of cast iron pipes 800 mm dia 100 metre 0.10 5972.04 597.20
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 24.35 298.50 7268.48 A
TOTAL 98865.68 W
Add 1 % Water charges on "W-A" 915.97
TOTAL 99781.65 X
Add GST on "X-A" (multiplying
factor 0.1405) 12998.10
TOTAL 112779.75 Y
Add 15% CPOH on "Y-A" 15826.69
TOTAL 128606.44 Z
Add Cess @ 1% on "Z-A" 1213.38
Cost of 10 metre 129819.82
Cost per metre 12981.98
Say 12982.00
SUB HEAD : 18- WATER SUPPLY 1639
18.72.13 900 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
900 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 282.74 Kg
Weight of 10m pipes 282.74x10
= 2827.40 Kg
7734 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 900mm dia metre 10.00 11800.00 118000.00
2356 Carriage of cast iron pipes 900 mm dia 100 metre 0.10 8958.06 895.81
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 28.27 298.50 8438.60 A
TOTAL 127334.40 W
Add 1 % Water charges on "W-A" 1188.96
TOTAL 128523.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 16871.91
TOTAL 145395.27 Y
Add 15% CPOH on "Y-A" 20543.50
TOTAL 165938.77 Z
Add Cess @ 1% on "Z-A" 1575.00
Cost of 10 metre 167513.77
Cost per metre 16751.38
Say 16751.40
18.72.14 1000 mm dia Ductile Iron Class K-7 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1000 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 348.23 Kg
Weight of 10m pipes 348.23x10
= 3482.30 Kg
7735 Ductile Iron Class K- 7 pipe conforming
to I.S. 8329 - 1000mm dia metre 10.00 12300.00 123000.00
2357 Carriage of cast iron pipes 1000 mm dia 100 metre 0.10 11944.08 1194.41
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 34.82 298.50 10393.77 A
TOTAL 134588.18 W
Add 1 % Water charges on "W-A" 1241.94
TOTAL 135830.12 X
Add GST on "X-A" (multiplying
factor 0.1405) 17623.81
TOTAL 153453.93 Y
Add 15% CPOH on "Y-A" 21459.02
TOTAL 174912.95 Z
Add Cess @ 1% on "Z-A" 1645.19
Cost of 10 metre 176558.15
Cost per metre 17655.81
Say 17655.80
SUB HEAD : 18- WATER SUPPLY 1640
18.72.15 100 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
100mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 17.76 Kg
Weight of 10m pipes 17.76x10
= 177.60 Kg
7651 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 100mm dia metre 10.00 765.00 7650.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.10 358.32 35.83
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 1.776 298.50 530.14 A
TOTAL 8215.97 W
Add 1 % Water charges on "W-A" 76.86
TOTAL 8292.83 X
Add GST on "X-A" (multiplying
factor 0.1405) 1090.66
TOTAL 9383.48 Y
Add 15% CPOH on "Y-A" 1328.00
TOTAL 10711.49 Z
Add Cess @ 1% on "Z-A" 101.81
Cost of 10 metre 10813.30
Cost per metre 1081.33
Say 1081.35
18.72.16 150 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
150 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 26.27 Kg
Weight of 10m pipes 26.27x10
= 262.70 Kg
7652 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 150mm dia metre 10.00 1150.00 11500.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.10 597.20 59.72
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 2.627 298.50 784.16 A
TOTAL 12343.88 W
Add 1 % Water charges on "W-A" 115.60
TOTAL 12459.48 X
Add GST on "X-A" (multiplying
factor 0.1405) 1640.38
TOTAL 14099.86 Y
Add 15% CPOH on "Y-A" 1997.35
TOTAL 16097.21 Z
Add Cess @ 1% on "Z-A" 153.13
Cost of 10 metre 16250.34
Cost per metre 1625.03
Say 1625.05
SUB HEAD : 18- WATER SUPPLY 1641
18.72.17 200 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
200 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 36.15 Kg
Weight of 10m pipes 36.15x10
= 361.50 Kg
7653 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 200mm dia metre 10.00 1575.00 15750.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.10 971.45 97.15
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 3.615 298.50 1079.08 A
TOTAL 16926.22 W
Add 1 % Water charges on "W-A" 158.47
TOTAL 17084.69 X
Add GST on "X-A" (multiplying
factor 0.1405) 2248.79
TOTAL 19333.48 Y
Add 15% CPOH on "Y-A" 2738.16
TOTAL 22071.64 Z
Add Cess @ 1% on "Z-A" 209.93
Cost of 10 metre 22281.57
Cost per metre 2228.16
Say 2228.15
18.72.18 250 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
250mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 48.00 Kg
Weight of 10m pipes 48.00x10
= 480.00 Kg
7654 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 250mm dia metre 10.00 2200.00 22000.00
2323 Carriage of Spun iron S & S pipes
250 mm dia 100 metre 0.10 1380.48 138.05
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 4.80 298.50 1432.80 A
TOTAL 23570.85 W
Add 1 % Water charges on "W-A" 221.38
TOTAL 23792.23 X
Add GST on "X-A" (multiplying
factor 0.1405) 3141.50
TOTAL 26933.73 Y
Add 15% CPOH on "Y-A" 3825.14
TOTAL 30758.87 Z
Add Cess @ 1% on "Z-A" 293.26
Cost of 10 metre 31052.13
Cost per metre 3105.21
Say 3105.20
SUB HEAD : 18- WATER SUPPLY 1642
18.72.19 300 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
300mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 60.490 Kg
Weight of 10m pipes 60.490x10
= 604.90 Kg
7655 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 300mm dia metre 10.00 2750.00 27500.00
2324 Carriage of Spun iron S & S pipes
300 mm dia 100 metre 0.10 1706.30 170.63
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 6.049 298.50 1805.63 A
TOTAL 29476.26 W
Add 1 % Water charges on "W-A" 276.71
TOTAL 29752.96 X
Add GST on "X-A" (multiplying
factor 0.1405) 3926.60
TOTAL 33679.56 Y
Add 15% CPOH on "Y-A" 4781.09
TOTAL 38460.65 Z
Add Cess @ 1% on "Z-A" 366.55
Cost of 10 metre 38827.20
Cost per metre 3882.72
Say 3882.70
18.72.20 350 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
350mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 79.730 Kg
Weight of 10m pipes 79.730x10
= 797.30 Kg
7656 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 350mm dia metre 10.00 3350.00 33500.00
2325 Carriage of Spun iron S & S pipes
350 mm dia 100 metre 0.10 2388.82 238.88
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 7.973 298.50 2379.94 A
TOTAL 36118.82 W
Add 1 % Water charges on "W-A" 337.39
TOTAL 36456.21 X
Add GST on "X-A" (multiplying
factor 0.1405) 4787.72
TOTAL 41243.93 Y
Add 15% CPOH on "Y-A" 5829.60
TOTAL 47073.53 Z
Add Cess @ 1% on "Z-A" 446.94
Cost of 10 metre 47520.46
Cost per metre 4752.05
Say 4752.05
SUB HEAD : 18- WATER SUPPLY 1643
18.72.21 400 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
400mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 94.800 Kg
Weight of 10m pipes 94.800x10
= 948.00 Kg
7657 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 400mm dia metre 10.00 4300.00 43000.00
2326 Carriage of Spun iron S & S pipes
400 mm dia 100 metre 0.10 3257.48 325.75
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 9.48 298.50 2829.78 A
TOTAL 46155.53 W
Add 1 % Water charges on "W-A" 433.26
TOTAL 46588.79 X
Add GST on "X-A" (multiplying
factor 0.1405) 6148.14
TOTAL 52736.93 Y
Add 15% CPOH on "Y-A" 7486.07
TOTAL 60223.00 Z
Add Cess @ 1% on "Z-A" 573.93
Cost of 10 metre 60796.93
Cost per metre 6079.69
Say 6079.70
18.72.22 450 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
450mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 110.970 Kg
Weight of 10m pipes 110.970x10
= 1109.70 Kg
7658 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 450mm dia metre 10.00 5000.00 50000.00
2327 Carriage of Spun iron S & S pipes
450 mm dia 100 metre 0.10 3981.36 398.14
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 11.097 298.50 3312.45 A
TOTAL 53710.59 W
Add 1 % Water charges on "W-A" 503.98
TOTAL 54214.57 X
Add GST on "X-A" (multiplying
factor 0.1405) 7151.75
TOTAL 61366.32 Y
Add 15% CPOH on "Y-A" 8708.08
TOTAL 70074.40 Z
Add Cess @ 1% on "Z-A" 667.62
Cost of 10 metre 70742.02
Cost per metre 7074.20
Say 7074.20
SUB HEAD : 18- WATER SUPPLY 1644
18.72.23 500 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
500mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 129.480 Kg
Weight of 10m pipes 129.480x10
= 1294.80 Kg
7659 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 500mm dia metre 10.00 6270.00 62700.00
2328 Carriage of Spun iron S & S pipes
500 mm dia 100 metre 0.10 3981.36 398.14
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 12.948 298.50 3864.98 A
TOTAL 66963.11 W
Add 1 % Water charges on "W-A" 630.98
TOTAL 67594.10 X
Add GST on "X-A" (multiplying
factor 0.1405) 8953.94
TOTAL 76548.04 Y
Add 15% CPOH on "Y-A" 10902.46
TOTAL 87450.50 Z
Add Cess @ 1% on "Z-A" 835.86
Cost of 10 metre 88286.35
Cost per metre 8828.64
Say 8828.65
18.72.24 600 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
600mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 168.680 Kg
Weight of 10m pipes 168.680x10
= 1686.80 Kg
7660 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 600mm dia metre 10.00 7560.00 75600.00
2329 Carriage of Spun iron S & S pipes
600mm dia 100 metre 0.10 5972.04 597.20
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 16.868 298.50 5035.10 A
TOTAL 81232.30 W
Add 1 % Water charges on "W-A" 761.97
TOTAL 81994.27 X
Add GST on "X-A" (multiplying
factor 0.1405) 10812.76
TOTAL 92807.04 Y
Add 15% CPOH on "Y-A" 13165.79
TOTAL 105972.83 Z
Add Cess @ 1% on "Z-A" 1009.38
Cost of 10 metre 106982.21
Cost per metre 10698.22
Say 10698.20
SUB HEAD : 18- WATER SUPPLY 1645
18.72.25 700 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
700mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 217.540 Kg
Weight of 10m pipes 217.540x10
= 2175.40 Kg
7661 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 700mm dia metre 10.00 10500.00 105000.00
2330 Carriage of C.I. pipes 500 mm dia 100 metre 0.10 3981.36 398.14
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 21.754 298.50 6493.57 A
TOTAL 111891.71 W
Add 1 % Water charges on "W-A" 1053.98
TOTAL 112945.69 X
Add GST on "X-A" (multiplying
factor 0.1405) 14956.52
TOTAL 127902.21 Y
Add 15% CPOH on "Y-A" 18211.30
TOTAL 146113.50 Z
Add Cess @ 1% on "Z-A" 1396.20
Cost of 10 metre 147509.70
Cost per metre 14750.97
Say 14750.95
18.72.26 750 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
750mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 242.600 Kg
Weight of 10m pipes 242.600x10
= 2426.00 Kg
7662 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 750mm dia metre 10.00 11350.00 113500.00
2331 Carriage of R.C.C. pipes 900 mm dia 100 metre 0.10 8958.06 895.81
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 24.26 298.50 7241.61 A
TOTAL 121637.42 W
Add 1 % Water charges on "W-A" 1143.96
TOTAL 122781.37 X
Add GST on "X-A" (multiplying
factor 0.1405) 16233.34
TOTAL 139014.71 Y
Add 15% CPOH on "Y-A" 19765.97
TOTAL 158780.68 Z
Add Cess @ 1% on "Z-A" 1515.39
Cost of 10 metre 160296.07
Cost per metre 16029.61
Say 16029.60
SUB HEAD : 18- WATER SUPPLY 1646
18.72.27 800 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
800 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 267.100 Kg
Weight of 10m pipes 267.100x10
= 2671.00 Kg
7663 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 800mm dia metre 10.00 11450.00 114500.00
2332 Carriage of R.C.C. pipes 1000 mm dia 100 metre 0.10 11944.08 1194.41
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 26.71 298.50 7972.94 A
TOTAL 123667.34 W
Add 1 % Water charges on "W-A" 1156.94
TOTAL 124824.29 X
Add GST on "X-A" (multiplying
factor 0.1405) 16417.61
TOTAL 141241.90 Y
Add 15% CPOH on "Y-A" 19990.35
TOTAL 161232.25 Z
Add Cess @ 1% on "Z-A" 1532.59
Cost of 10 metre 162764.84
Cost per metre 16276.48
Say 16276.50
18.72.28 900 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
900 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 321.290 Kg
Weight of 10m pipes 321.290x10
= 3212.90 Kg
7664 Ductile Iron class K - 9 pipe
Conforming to I.S. 8329 - 900mm dia metre 10.00 13900.00 139000.00
2333 Carriage of R.C.C. pipes 1100 mm dia 100 metre 0.10 11944.08 1194.41
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 32.129 298.50 9590.51 A
TOTAL 149784.91 W
Add 1 % Water charges on "W-A" 1401.94
TOTAL 151186.86 X
Add GST on "X-A" (multiplying
factor 0.1405) 19894.29
TOTAL 171081.15 Y
Add 15% CPOH on "Y-A" 24223.60
TOTAL 195304.74 Z
Add Cess @ 1% on "Z-A" 1857.14
Cost of 10 metre 197161.88
Cost per metre 19716.19
Say 19716.20
SUB HEAD : 18- WATER SUPPLY 1647
18.72.29 1000 mm dia Ductile Iron Class K-9 pipes
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1000 mm dia. cast iron pipes
(in 5.5 m lengths)
Weight of 1 m pipes = 380.190 Kg
Weight of 10m pipes 380.190x10
= 3801.90 Kg
7665 Ductile Iron class K - 9 pipe Conforming
to I.S. 8329 - 1000mm dia metre 10.00 15550.00 155500.00
2334 Carriage of R.C.C. pipes 1200 mm dia 100 metre 0.10 11944.08 1194.41
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 38.019 298.50 11348.67 A
TOTAL 168043.08 W
Add 1 % Water charges on "W-A" 1566.94
TOTAL 169610.02 X
Add GST on "X-A" (multiplying
factor 0.1405) 22235.72
TOTAL 191845.74 Y
Add 15% CPOH on "Y-A" 27074.56
TOTAL 218920.30 Z
Add Cess @ 1% on "Z-A" 2075.72
Cost of 10 metre 220996.02
Cost per metre 22099.60
Say 22099.60
18.73 Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun)
Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :
18.73.1 100 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
100 mm dia. ductile iron pipes double
flanged
Weight of 1 m pipes = 21.700 Kg
Weight of 5 m pipes 21.700x5
= 108.50 Kg
7686 Ductile Iron Pipe Class K-9 flanges
and welding 100mm dia metre 5.00 1100.00 5500.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.05 358.32 17.92
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 1.09 298.50 325.37 A
TOTAL 5843.28 W
Add 1 % Water charges on "W-A" 55.18
TOTAL 5898.46 X
Add GST on "X-A" (multiplying
factor 0.1405) 783.02
TOTAL 6681.48 Y
Add 15% CPOH on "Y-A" 953.42
TOTAL 7634.90 Z
Add Cess @ 1% on "Z-A" 73.10
Cost of 5 metre 7707.99
Cost per metre 1541.60
Say 1541.60
SUB HEAD : 18- WATER SUPPLY 1648
18.73.2 150 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
150 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 32.600 Kg
Weight of 5 m pipes 32.600x5
= 163.00 Kg
7687 Ductile Iron Pipe Class K-9 flanges
and welding 150 dia metre 5.00 1650.00 8250.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.05 597.20 29.86
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 1.63 298.50 486.56 A
TOTAL 8766.42 W
Add 1 % Water charges on "W-A" 82.80
TOTAL 8849.21 X
Add GST on "X-A" (multiplying
factor 0.1405) 1174.95
TOTAL 10024.17 Y
Add 15% CPOH on "Y-A" 1430.64
TOTAL 11454.81 Z
Add Cess @ 1% on "Z-A" 109.68
Cost of 5 metre 11564.49
Cost per metre 2312.90
Say 2312.90
18.73.3 200 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
200 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 44.200 Kg
Weight of 5 m pipes 44.200x5
= 221.00 Kg
7688 Ductile Iron Pipe Class K-9 flanges
and welding 200mm dia metre 5.00 2075.00 10375.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.05 971.45 48.57
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 2.21 298.50 659.69 A
TOTAL 11083.26 W
Add 1 % Water charges on "W-A" 104.24
TOTAL 11187.49 X
Add GST on "X-A" (multiplying
factor 0.1405) 1479.16
TOTAL 12666.65 Y
Add 15% CPOH on "Y-A" 1801.04
TOTAL 14467.70 Z
Add Cess @ 1% on "Z-A" 138.08
Cost of 5 metre 14605.78
Cost per metre 2921.16
Say 2921.15
SUB HEAD : 18- WATER SUPPLY 1649
18.73.4 250 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
250 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 59.400 Kg
Weight of 5 m pipes 59.400x5
= 297.00 Kg
7689 Ductile Iron Pipe Class K-9 flanges
and welding 250mm dia metre 5.00 2950.00 14750.00
2323 Carriage of Spun iron S & S pipes
250 mm dia 100 metre 0.05 1380.48 69.02
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 2.97 298.50 886.55 A
TOTAL 15705.57 W
Add 1 % Water charges on "W-A" 148.19
TOTAL 15853.76 X
Add GST on "X-A" (multiplying
factor 0.1405) 2102.89
TOTAL 17956.65 Y
Add 15% CPOH on "Y-A" 2560.52
TOTAL 20517.17 Z
Add Cess @ 1% on "Z-A" 196.31
Cost of 5 metre 20713.48
Cost per metre 4142.70
Say 4142.70
18.73.5 300 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
300 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 76.400 Kg
Weight of 5 m pipes 76.400x5
= 382.00 Kg
7690 Ductile Iron Pipe Class K-9 flanges
and welding 300mm dia metre 5.00 3790.00 18950.00
2324 Carriage of Spun iron S & S pipes
300 mm dia 100 metre 0.05 1706.30 85.32
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 3.82 298.50 1140.27 A
TOTAL 20175.59 W
Add 1 % Water charges on "W-A" 190.35
TOTAL 20365.94 X
Add GST on "X-A" (multiplying
factor 0.1405) 2701.21
TOTAL 23067.14 Y
Add 15% CPOH on "Y-A" 3289.03
TOTAL 26356.18 Z
Add Cess @ 1% on "Z-A" 252.16
Cost of 5 metre 26608.33
Cost per metre 5321.67
Say 5321.65
SUB HEAD : 18- WATER SUPPLY 1650
18.73.6 350 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
350 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 91.400 Kg
Weight of 5 m pipes 91.400x5
= 457.00 Kg
7691 Ductile Iron Pipe Class K-9 flanges
and welding 350mm dia metre 5.00 4780.00 23900.00
2325 Carriage of Spun iron S & S pipes
350 mm dia 100 metre 0.05 2388.82 119.44
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 4.57 298.50 1364.15 A
TOTAL 25383.59 W
Add 1 % Water charges on "W-A" 240.19
TOTAL 25623.78 X
Add GST on "X-A" (multiplying
factor 0.1405) 3408.48
TOTAL 29032.26 Y
Add 15% CPOH on "Y-A" 4150.22
TOTAL 33182.48 Z
Add Cess @ 1% on "Z-A" 318.18
Cost of 5 metre 33500.66
Cost per metre 6700.13
Say 6700.15
18.73.7 400 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
400 mm dia. ductile iron pipes double
flanged
Weight of 1 m pipes = 108.100 Kg
Weight of 5 m pipes 108.100x5
= 540.50 Kg
7692 Ductile Iron Pipe Class K-9 flanges
and welding 400mm dia metre 5.00 6150.00 30750.00
2326 Carriage of Spun iron S & S pipes
400 mm dia 100 metre 0.05 3257.48 162.87
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 5.40 298.50 1611.90 A
TOTAL 32524.77 W
Add 1 % Water charges on "W-A" 309.13
TOTAL 32833.90 X
Add GST on "X-A" (multiplying
factor 0.1405) 4386.69
TOTAL 37220.59 Y
Add 15% CPOH on "Y-A" 5341.30
TOTAL 42561.90 Z
Add Cess @ 1% on "Z-A" 409.50
Cost of 5 metre 42971.40
Cost per metre 8594.28
Say 8594.30
SUB HEAD : 18- WATER SUPPLY 1651
18.73.8 450 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
450 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 127.800 Kg
Weight of 5 m pipes 127.800x5
= 639.00 Kg
7693 Ductile Iron Pipe Class K-9 flanges
and welding 450mm dia metre 5.00 6453.00 32265.00
2327 Carriage of Spun iron S & S pipes
450 mm dia 100 metre 0.05 3981.36 199.07
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 6.39 298.50 1907.42 A
TOTAL 34371.48 W
Add 1 % Water charges on "W-A" 324.64
TOTAL 34696.12 X
Add GST on "X-A" (multiplying
factor 0.1405) 4606.81
TOTAL 39302.94 Y
Add 15% CPOH on "Y-A" 5609.33
TOTAL 44912.27 Z
Add Cess @ 1% on "Z-A" 430.05
Cost of 5 metre 45342.31
Cost per metre 9068.46
Say 9068.45
18.73.9 500 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
500 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 147.900 Kg
Weight of 5 m pipes 147.900x5
= 739.50 Kg
7694 Ductile Iron Pipe Class K-9 flanges
and welding 500mm dia metre 5.00 9180.00 45900.00
2328 Carriage of Spun iron S & S pipes
500 mm dia 100 metre 0.05 3981.36 199.07
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 7.40 298.50 2208.90 A
TOTAL 48307.97 W
Add 1 % Water charges on "W-A" 460.99
TOTAL 48768.96 X
Add GST on "X-A" (multiplying
factor 0.1405) 6541.69
TOTAL 55310.65 Y
Add 15% CPOH on "Y-A" 7965.26
TOTAL 63275.91 Z
Add Cess @ 1% on "Z-A" 610.67
Cost of 5 metre 63886.58
Cost per metre 12777.32
Say 12777.30
SUB HEAD : 18- WATER SUPPLY 1652
18.73.10 600 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
600 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 198.900 Kg
Weight of 5 m pipes 198.900x5
= 994.50 Kg
7695 Ductile Iron Pipe Class K-9 flanges
and welding 600mm dia metre 5.00 12150.00 60750.00
2329 Carriage of Spun iron S & S pipes
600mm dia 100 metre 0.05 5972.04 298.60
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 9.95 298.50 2970.08 A
TOTAL 64018.68 W
Add 1 % Water charges on "W-A" 610.49
TOTAL 64629.16 X
Add GST on "X-A" (multiplying
factor 0.1405) 8663.10
TOTAL 73292.26 Y
Add 15% CPOH on "Y-A" 10548.33
TOTAL 83840.59 Z
Add Cess @ 1% on "Z-A" 808.71
Cost of 5 metre 84649.30
Cost per metre 16929.86
Say 16929.85
18.73.11 700 mm dia Ductile Iron Double Flanged
Code Description Unit Quantity Rate Amount
Details of cost for 5 metre
MATERIAL
700 mm dia. ductile iron pipes
double flanged
Weight of 1 m pipes = 254.900 Kg
Weight of 5 m pipes 254.900x5
= 1274.50 Kg
7696 Ductile Iron Pipe Class K-9 flanges
and welding 700mm dia metre 5.00 14370.00 71850.00
2330 Carriage of C.I. pipes 500 mm dia 100 metre 0.05 3981.36 199.07
Labour for laying
18.23 Rate as per Item Number 18.23 of
SH: Water Supply quintal 12.75 298.50 3805.88 A
TOTAL 75854.94 W
Add 1 % Water charges on "W-A" 720.49
TOTAL 76575.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 10224.12
TOTAL 86799.56 Y
Add 15% CPOH on "Y-A" 12449.05
TOTAL 99248.61 Z
Add Cess @ 1% on "Z-A" 954.43
Cost of 5 metre 100203.04
Cost per metre 20040.61
Say 20040.60
SUB HEAD : 18- WATER SUPPLY 1653
18.74 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar
and bush of approved quality and colour.
18.74.1 15 mm nominal bore with 30cm length
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7862 15 mm nominal bore and 30 cm
length PVC connection pipe with
P.T.M.T. Nuts each 1.00 38.00 38.00
9988 Carriage of materials and fixing charges L.S. 12.22 2.12 25.91
TOTAL 63.91 W
Add 1 % Water charges on "W" 0.64
TOTAL 64.55 X
Add GST on "X" (multiplying
factor 0.1405) 9.07
TOTAL 73.61 Y
Add 15% CPOH on "Y" 11.04
TOTAL 84.66 Z
Add Cess @ 1% on "Z" 0.85
Cost of one no. 85.50
Say 85.50
18.74.2 15 mm nominal bore with 45 cm length
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7863 15 mm nominal bore and 45 cm
length PVC connection pipe with
P.T.M.T. Nuts each 1.00 52.00 52.00
9988 Carriage of materials and fixing charges L.S. 13.52 2.12 28.66
TOTAL 80.66 W
Add 1 % Water charges on "W" 0.81
TOTAL 81.47 X
Add GST on "X" (multiplying
factor 0.1405) 11.45
TOTAL 92.92 Y
Add 15% CPOH on "Y" 13.94
TOTAL 106.85 Z
Add Cess @ 1% on "Z" 1.07
Cost of one no. 107.92
Say 107.90
18.75 Providing and fixing PTMT extension nipple for water tank pipe, fittings of
approved quality and colour.
18.75.1 15 mm nominal bore, weighing not less than 32 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7864 P.T.M.T. extension nipple 15mm each 1.00 25.00 25.00
SUB HEAD : 18- WATER SUPPLY 1654
Code Description Unit Quantity Rate Amount
9988 Carriage of materials and fixing charges L.S. 3.38 2.12 7.17
TOTAL 32.17 W
Add 1 % Water charges on "W" 0.32
TOTAL 32.49 X
Add GST on "X" (multiplying
factor 0.1405) 4.56
TOTAL 37.05 Y
Add 15% CPOH on "Y" 5.56
TOTAL 42.61 Z
Add Cess @ 1% on "Z" 0.43
Cost of one no. 43.04
Say 43.05
18.75.2 20 mm nominal bore, weighing not less than 40 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7865 P.T.M.T. extension nipple 20mm each 1.00 50.00 50.00
9988 Carriage of materials and fixing charges L.S. 3.38 2.12 7.17
TOTAL 57.17 W
Add 1 % Water charges on "W" 0.57
TOTAL 57.74 X
Add GST on "X" (multiplying
factor 0.1405) 8.11
TOTAL 65.85 Y
Add 15% CPOH on "Y" 9.88
TOTAL 75.73 Z
Add Cess @ 1% on "Z" 0.76
Cost of one no. 76.48
Say 76.50
18.75.3 25mm nominal bore, weighing not less than 62 gms
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7866 P.T.M.T. extension nipple 25mm each 1.00 68.00 68.00
9988 Carriage of materials and fixing charges L.S. 3.38 2.12 7.17
TOTAL 75.17 W
Add 1 % Water charges on "W" 0.75
TOTAL 75.92 X
Add GST on "X" (multiplying
factor 0.1405) 10.67
TOTAL 86.58 Y
Add 15% CPOH on "Y" 12.99
TOTAL 99.57 Z
Add Cess @ 1% on "Z" 1.00
Cost of one no. 100.57
Say 100.55
SUB HEAD : 18- WATER SUPPLY 1655
18.76 Cutting holes up to 30x30 cm in walls including making good the same:
18.76.1 With common burnt clay F.P.S. (non modular) bricks
Code Description Unit Quantity Rate Amount
Details of cost for 10 holes
Size 30x30 cm in 34 cm wall
Labour for cutting holes
0123 Mason (brick layer) 1st class day 0.16 784.00 125.44
0124 Mason (brick layer) 2nd class day 0.16 714.00 114.24
0114 Beldar day 1.25 645.00 806.25
Brick work with bricks of class
designation 75 in cement mortar
1:4 (1 cement : 4 coarse sand)
10x0.30x0.30x0.344m = 0.309 cum
Less 33% for pipe etc. = (-) 0.102 cum
= 0.207 cum Say 0.21 cum
6.4.1 Rate as per item No 6.4.1 of
SH :- Brick work. cum 0.21 8512.10 1787.54 A
12 mm cement plaster 1:4 (1 cement :
4 coarse sand)
10x2x0.3x0.3m = 1.80 sqm
Les 33% for pipe etc. = (-) 0.59 sqm
= 1.21 sqm Say 1.20 sqm
13.4.1 (Rate as per item no 13.4.1 of
SH : Finishing) sqm 1.20 307.25 368.70 A
9999 Add for delay L.S. 16.12 2.12 34.17
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 3253.43 W
Add 1 % Water charges on "W-A" 10.97
TOTAL 3264.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 155.70
TOTAL 3420.10 Y
Add 15% CPOH on "Y-A" 189.58
TOTAL 3609.68 Z
Add Cess @ 1% on "Z-A" 14.53
Cost of 10 holes 3624.21
Cost of 1 hole 362.42
Say 362.40
18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe
etc. and repairing the hole after insertion of drain pipe etc. with cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size), including finishing complete so as to make it leak proof.
Code Description Unit Quantity Rate Amount
Details of cost for 10 holes
Average size 15x15x15 cm
Labour for cutting holes
0123 Mason (brick layer) 1st class day 0.83 784.00 650.72
0124 Mason (brick layer) 2nd class day 0.83 714.00 592.62
SUB HEAD : 18- WATER SUPPLY 1656
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.67 645.00 1077.15
Cement concrete 1:2:4 (1 cement :
2 coarse sand ; 4 graded stone
aggregate 20 mm nominal size)
10x0.15x0.15x0.15 m = 0.033 cum
Les 33% for pipe etc. = (-) 0.011 cum
= 0.022 cum Say 0.0.02 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete Work cum 0.02 7365.15 147.30 A
9999 Finishing top and bottom and making
the holes leak proof L.S. 121.16 2.12 256.86
9999 Add for delay L.S. 40.30 2.12 85.44
9999 Sundries L.S. 21.58 2.12 45.75
TOTAL 2855.84 W
Add 1 % Water charges on "W-A" 27.09
TOTAL 2882.92 X
Add GST on "X-A" (multiplying
factor 0.1405) 384.35
TOTAL 3267.28 Y
Add 15% CPOH on "Y-A" 468.00
TOTAL 3735.27 Z
Add Cess @ 1% on "Z-A" 35.88
Cost of 10 holes 3771.15
Cost of 1 hole 377.12
Say 377.10
18.78 Making chases up to 7.5x7.5 cm in walls including making good and finishing
with matching surface after housing G.I. pipe etc.
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
Labour for making chases
0123 Mason (brick layer) 1st class day 0.25 784.00 196.00
0124 Mason (brick layer) 2nd class day 0.25 714.00 178.50
0114 Beldar day 1.00 645.00 645.00
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
0.075x0.075x10 m = 0.05625 cum
Les 33% for pipe etc. = (-) 0.01856 cum
= 0.03769 cum Say 0.04 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.04 8843.45 353.74 A
TOTAL 1373.24 W
Add 1 % Water charges on "W-A" 10.20
TOTAL 1383.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 144.67
TOTAL 1528.11 Y
Add 15% CPOH on "Y-A" 176.16
TOTAL 1704.26 Z
Add Cess @ 1% on "Z-A" 13.51
Cost of 10 metre 1717.77
Cost of 1 metre 171.78
Say 171.80
SUB HEAD : 18- WATER SUPPLY 1657
18.79 Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in
masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand: 6
graded stone aggregate 20 mm nominal size) including disposal of malba.
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
0.2x0.2x10 m = 0.40 cum
Les for pipe 3.14x(0.15)²/4x10
= (-) 0.177 cum
= 0.223 cum Say 0.22 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.22 8843.45 1945.56 A
9999 Disposal of malba L.S. 13.52 2.12 28.66
TOTAL 1974.22 W
Add 1 % Water charges on "W-A" 0.29
TOTAL 1974.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.07
TOTAL 1978.58 Y
Add 15% CPOH on "Y-A" 4.95
TOTAL 1983.53 Z
Add Cess @ 1% on "Z-A" 0.38
Cost of 10 metre 1983.91
Cost of 1 metre 198.39
Say 198.40
18.80 Disinfecting C.I. water mains by flushing with water containing bleaching powder
@ 0.5 gms per litre of water and cleaning the same with fresh water, operation
to be repeated three times including getting the sample of water from the
disinfected main tested in the municipal laboratory.
18.80.1 80 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(80/10)²x(100x100)/1000x
0.5 gms = 754.28 gms Say 0.008 q
1301 Bleaching powder quintal 0.008 1800.00 14.40
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0114 Beldar day 1.31 645.00 844.95
9999 Sundries including testing of samples L.S. 9.88 2.12 20.95
TOTAL 1139.02 W
Add 1 % Water charges on "W" 11.39
TOTAL 1150.41 X
Add GST on "X" (multiplying
factor 0.1405) 161.63
TOTAL 1312.04 Y
Add 15% CPOH on "Y" 196.81
TOTAL 1508.84 Z
Add Cess @ 1% on "Z" 15.09
Cost of 100 metre 1523.93
Say 1523.95
SUB HEAD : 18- WATER SUPPLY 1658
18.80.2 100 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(100/10)²x(100x100)/1000x
0.5 gms = 1178.57 gms Say 0.012 q
1301 Bleaching powder quintal 0.012 1800.00 21.60
LABOUR
0116 Fitter (grade 1) day 0.49 784.00 384.16
0114 Beldar day 1.64 645.00 1057.80
9999 Sundries including testing of samples L.S. 13.52 2.12 28.66
TOTAL 1492.22 W
Add 1 % Water charges on "W" 14.92
TOTAL 1507.14 X
Add GST on "X" (multiplying
factor 0.1405) 211.75
TOTAL 1718.90 Y
Add 15% CPOH on "Y" 257.83
TOTAL 1976.73 Z
Add Cess @ 1% on "Z" 19.77
Cost of 100 metre 1996.50
Say 1996.50
18.80.3 125 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(125/10)²x(100x100)/1000x
0.5 gms = 1841.52 gms Say 0.018 q
1301 Bleaching powder quintal 0.018 1800.00 32.40
LABOUR
0116 Fitter (grade 1) day 0.66 784.00 517.44
0114 Beldar day 1.97 645.00 1270.65
9999 Sundries including testing of samples L.S. 17.94 2.12 38.03
TOTAL 1858.52 W
Add 1 % Water charges on "W" 18.59
TOTAL 1877.11 X
Add GST on "X" (multiplying
factor 0.1405) 263.73
TOTAL 2140.84 Y
Add 15% CPOH on "Y" 321.13
TOTAL 2461.97 Z
Add Cess @ 1% on "Z" 24.62
Cost of 100 metre 2486.59
Say 2486.60
SUB HEAD : 18- WATER SUPPLY 1659
18.80.4 150 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(150/10)²x(100x100)/1000x
0.5 gms = 2651 gms Say 0.027 q
1301 Bleaching powder quintal 0.027 1800.00 48.60
LABOUR
0116 Fitter (grade 1) day 0.82 784.00 642.88
0114 Beldar day 2.30 645.00 1483.50
9999 Sundries including testing of samples L.S. 22.88 2.12 48.51
TOTAL 2223.49 W
Add 1 % Water charges on "W" 22.23
TOTAL 2245.72 X
Add GST on "X" (multiplying
factor 0.1405) 315.52
TOTAL 2561.24 Y
Add 15% CPOH on "Y" 384.19
TOTAL 2945.43 Z
Add Cess @ 1% on "Z" 29.45
Cost of 100 metre 2974.89
Say 2974.90
18.80.5 200 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(200/10)²x(100x100)/1000x
0.5 gms = 4712.39 gms Say 0.047 q
1301 Bleaching powder quintal 0.047 1800.00 84.60
LABOUR
0116 Fitter (grade 1) day 1.15 784.00 901.60
0114 Beldar day 2.95 645.00 1902.75
9999 Sundries including testing of samples L.S. 31.46 2.12 66.70
TOTAL 2955.65 W
Add 1 % Water charges on "W" 29.56
TOTAL 2985.20 X
Add GST on "X" (multiplying
factor 0.1405) 419.42
TOTAL 3404.62 Y
Add 15% CPOH on "Y" 510.69
TOTAL 3915.32 Z
Add Cess @ 1% on "Z" 39.15
Cost of 100 metre 3954.47
Say 3954.45
SUB HEAD : 18- WATER SUPPLY 1660
18.80.6 250 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(250/10)²x(100x100)/1000x
0.5 gms = 7363.10 gms Say 0.074 q
1301 Bleaching powder quintal 0.074 1800.00 133.20
LABOUR
0116 Fitter (grade 1) day 1.48 784.00 1160.32
0114 Beldar day 3.61 645.00 2328.45
9999 Sundries including testing of samples L.S. 40.30 2.12 85.44
TOTAL 3707.41 W
Add 1 % Water charges on "W" 37.07
TOTAL 3744.48 X
Add GST on "X" (multiplying
factor 0.1405) 526.10
TOTAL 4270.58 Y
Add 15% CPOH on "Y" 640.59
TOTAL 4911.17 Z
Add Cess @ 1% on "Z" 49.11
Cost of 100 metre 4960.28
Say 4960.30
18.80.7 300 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(300/10)²x(100x100)/1000x
0.5 gms = 10602.88 gms Say 0.106 q
1301 Bleaching powder quintal 0.106 1800.00 190.80
LABOUR
0116 Fitter (grade 1) day 1.64 784.00 1285.76
0114 Beldar day 3.94 645.00 2541.30
9999 Sundries including testing of samples L.S. 44.46 2.12 94.26
TOTAL 4112.12 W
Add 1 % Water charges on "W" 41.12
TOTAL 4153.24 X
Add GST on "X" (multiplying
factor 0.1405) 583.53
TOTAL 4736.77 Y
Add 15% CPOH on "Y" 710.51
TOTAL 5447.28 Z
Add Cess @ 1% on "Z" 54.47
Cost of 100 metre 5501.75
Say 5501.75
SUB HEAD : 18- WATER SUPPLY 1661
18.80.8 350 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(350/10)²x(100x100)/1000x
0.5 gms = 14431.70 gms Say 0.144 q
1301 Bleaching powder quintal 0.144 1800.00 259.20
LABOUR
0116 Fitter (grade 1) day 1.80 784.00 1411.20
0114 Beldar day 4.27 645.00 2754.15
9999 Sundries including testing of samples L.S. 48.36 2.12 102.52
TOTAL 4527.07 W
Add 1 % Water charges on "W" 45.27
TOTAL 4572.34 X
Add GST on "X" (multiplying
factor 0.1405) 642.41
TOTAL 5214.76 Y
Add 15% CPOH on "Y" 782.21
TOTAL 5996.97 Z
Add Cess @ 1% on "Z" 59.97
Cost of 100 metre 6056.94
Say 6056.95
18.80.9 400 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(400/10)²x(100x100)/1000x
0.5 gms = 18849.60 gms Say 0.189 q
1301 Bleaching powder quintal 0.189 1800.00 340.20
LABOUR
0116 Fitter (grade 1) day 1.97 784.00 1544.48
0114 Beldar day 4.59 645.00 2960.55
9999 Sundries including testing of samples L.S. 53.82 2.12 114.10
TOTAL 4959.33 W
Add 1 % Water charges on "W" 49.59
TOTAL 5008.92 X
Add GST on "X" (multiplying
factor 0.1405) 703.75
TOTAL 5712.68 Y
Add 15% CPOH on "Y" 856.90
TOTAL 6569.58 Z
Add Cess @ 1% on "Z" 65.70
Cost of 100 metre 6635.27
Say 6635.25
SUB HEAD : 18- WATER SUPPLY 1662
18.80.10 450 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(450/10)²x(100x100)/1000x
0.5 gms = 23856.50 gms Say 0.239 q
1301 Bleaching powder quintal 0.239 1800.00 430.20
LABOUR
0116 Fitter (grade 1) day 2.13 784.00 1669.92
0114 Beldar day 4.92 645.00 3173.40
9999 Sundries including testing of samples L.S. 58.24 2.12 123.47
TOTAL 5396.99 W
Add 1 % Water charges on "W" 53.97
TOTAL 5450.96 X
Add GST on "X" (multiplying
factor 0.1405) 765.86
TOTAL 6216.82 Y
Add 15% CPOH on "Y" 932.52
TOTAL 7149.34 Z
Add Cess @ 1% on "Z" 71.49
Cost of 100 metre 7220.83
Say 7220.85
18.80.11 500 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(500/10)²x(100x100)/1000x
0.5 gms = 29452.40 gms Say 0.295 q
1301 Bleaching powder quintal 0.295 1800.00 531.00
LABOUR
0116 Fitter (grade 1) day 2.30 784.00 1803.20
0114 Beldar day 5.25 645.00 3386.25
9999 Sundries including testing of samples L.S. 63.7 2.12 135.04
TOTAL 5855.49 W
Add 1 % Water charges on "W" 58.55
TOTAL 5914.05 X
Add GST on "X" (multiplying
factor 0.1405) 830.92
TOTAL 6744.97 Y
Add 15% CPOH on "Y" 1011.75
TOTAL 7756.72 Z
Add Cess @ 1% on "Z" 77.57
Cost of 100 metre 7834.29
Say 7834.30
SUB HEAD : 18- WATER SUPPLY 1663
18.80.12 600 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
Bleaching powder
3x3.14/4x(600/10)²x(100x100)/1000x
0.5 gms = 42411.5 gms Say 0.424 q
1301 Bleaching powder quintal 0.424 1800.00 763.20
LABOUR
0116 Fitter (grade 1) day 2.62 784.00 2054.08
0114 Beldar day 5.91 645.00 3811.95
9999 Sundries including testing of samples L.S. 71.37 2.12 151.30
TOTAL 6780.53 W
Add 1 % Water charges on "W" 67.81
TOTAL 6848.34 X
Add GST on "X" (multiplying
factor 0.1405) 962.19
TOTAL 7810.53 Y
Add 15% CPOH on "Y" 1171.58
TOTAL 8982.11 Z
Add Cess @ 1% on "Z" 89.82
Cost of 100 metre 9071.93
Say 9071.95
18.81 Extra for every operation of disinfecting the C.I. main by flushing with water
containing bleaching powder @ 0.5 gms per litre of water and cleaning the same
with fresh water, including getting the samples of water tested in the municipal
laboratory :
18.81.1 80 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.003 1800.00 5.40
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.49 645.00 316.05
9999 Sundries including testing of samples L.S. 4.42 2.12 9.37
TOTAL 417.06 W
Add 1 % Water charges on "W" 4.17
TOTAL 421.23 X
Add GST on "X" (multiplying
factor 0.1405) 59.18
TOTAL 480.41 Y
Add 15% CPOH on "Y" 72.06
TOTAL 552.48 Z
Add Cess @ 1% on "Z" 5.52
Cost of 100 metre 558.00
Say 558.00
SUB HEAD : 18- WATER SUPPLY 1664
18.81.2 100 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.004 1800.00 7.20
LABOUR
0116 Fitter (grade 1) day 0.16 784.00 125.44
0114 Beldar day 0.57 645.00 367.65
9999 Sundries including testing of samples L.S. 4.42 2.12 9.37
TOTAL 509.66 W
Add 1 % Water charges on "W" 5.10
TOTAL 514.76 X
Add GST on "X" (multiplying
factor 0.1405) 72.32
TOTAL 587.08 Y
Add 15% CPOH on "Y" 88.06
TOTAL 675.14 Z
Add Cess @ 1% on "Z" 6.75
Cost of 100 metre 681.89
Say 681.90
18.81.3 125 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.006 1800.00 10.80
LABOUR
0116 Fitter (grade 1) day 0.22 784.00 172.48
0114 Beldar day 0.66 645.00 425.70
9999 Sundries including testing of samples L.S. 5.46 2.12 11.58
TOTAL 620.56 W
Add 1 % Water charges on "W" 6.21
TOTAL 626.76 X
Add GST on "X" (multiplying
factor 0.1405) 88.06
TOTAL 714.82 Y
Add 15% CPOH on "Y" 107.22
TOTAL 822.04 Z
Add Cess @ 1% on "Z" 8.22
Cost of 100 metre 830.26
Say 830.25
18.81.4 150 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.009 1800.00 16.20
LABOUR
0116 Fitter (grade 1) day 0.27 784.00 211.68
SUB HEAD : 18- WATER SUPPLY 1665
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.74 645.00 477.30
9999 Sundries including testing of samples L.S. 7.15 2.12 15.16
TOTAL 720.34 W
Add 1 % Water charges on "W" 7.20
TOTAL 727.54 X
Add GST on "X" (multiplying
factor 0.1405) 102.22
TOTAL 829.76 Y
Add 15% CPOH on "Y" 124.46
TOTAL 954.23 Z
Add Cess @ 1% on "Z" 9.54
Cost of 100 metre 963.77
Say 963.75
18.81.5 200 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.016 1800.00 28.80
LABOUR
0116 Fitter (grade 1) day 0.58 784.00 454.72
0114 Beldar day 0.90 645.00 580.50
9999 Sundries including testing of samples L.S. 9.88 2.12 20.95
TOTAL 1084.97 W
Add 1 % Water charges on "W" 10.85
TOTAL 1095.82 X
Add GST on "X" (multiplying
factor 0.1405) 153.96
TOTAL 1249.78 Y
Add 15% CPOH on "Y" 187.47
TOTAL 1437.24 Z
Add Cess @ 1% on "Z" 14.37
Cost of 100 metre 1451.62
Say 1451.60
18.81.6 250 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.025 1800.00 45.00
LABOUR
0116 Fitter (grade 1) day 0.60 784.00 470.40
0114 Beldar day 1.10 645.00 709.50
SUB HEAD : 18- WATER SUPPLY 1666
Code Description Unit Quantity Rate Amount
9999 Sundries including testing of samples L.S. 10.79 2.12 22.87
TOTAL 1247.77 W
Add 1 % Water charges on "W" 12.48
TOTAL 1260.25 X
Add GST on "X" (multiplying
factor 0.1405) 177.07
TOTAL 1437.32 Y
Add 15% CPOH on "Y" 215.60
TOTAL 1652.92 Z
Add Cess @ 1% on "Z" 16.53
Cost of 100 metre 1669.44
Say 1669.45
18.81.7 300 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.035 1800.00 63.00
LABOUR
0116 Fitter (grade 1) day 0.60 784.00 470.40
0114 Beldar day 1.30 645.00 838.50
9999 Sundries including testing of samples L.S. 13.52 2.12 28.66
TOTAL 1400.56 W
Add 1 % Water charges on "W" 14.01
TOTAL 1414.57 X
Add GST on "X" (multiplying
factor 0.1405) 198.75
TOTAL 1613.31 Y
Add 15% CPOH on "Y" 242.00
TOTAL 1855.31 Z
Add Cess @ 1% on "Z" 18.55
Cost of 100 metre 1873.87
Say 1873.85
18.81.8 350 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.048 1800.00 86.40
LABOUR
0116 Fitter (grade 1) day 0.70 784.00 548.80
0114 Beldar day 1.50 645.00 967.50
SUB HEAD : 18- WATER SUPPLY 1667
Code Description Unit Quantity Rate Amount
9999 Sundries including testing of samples L.S. 16.12 2.12 34.17
TOTAL 1636.87 W
Add 1 % Water charges on "W" 16.37
TOTAL 1653.24 X
Add GST on "X" (multiplying
factor 0.1405) 232.28
TOTAL 1885.52 Y
Add 15% CPOH on "Y" 282.83
TOTAL 2168.35 Z
Add Cess @ 1% on "Z" 21.68
Cost of 100 metre 2190.04
Say 2190.05
18.81.9 400 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.063 1800.00 113.40
LABOUR
0116 Fitter (grade 1) day 0.80 784.00 627.20
0114 Beldar day 1.70 645.00 1096.50
9999 Sundries including testing of samples L.S. 17.94 2.12 38.03
TOTAL 1875.13 W
Add 1 % Water charges on "W" 18.75
TOTAL 1893.88 X
Add GST on "X" (multiplying
factor 0.1405) 266.09
TOTAL 2159.97 Y
Add 15% CPOH on "Y" 324.00
TOTAL 2483.97 Z
Add Cess @ 1% on "Z" 24.84
Cost of 100 metre 2508.81
Say 2508.80
18.81.10 450 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.08 1800.00 144.00
LABOUR
0116 Fitter (grade 1) day 0.90 784.00 705.60
0114 Beldar day 1.90 645.00 1225.50
SUB HEAD : 18- WATER SUPPLY 1668
Code Description Unit Quantity Rate Amount
9999 Sundries including testing of samples L.S. 20.67 2.12 43.82
TOTAL 2118.92 W
Add 1 % Water charges on "W" 21.19
TOTAL 2140.11 X
Add GST on "X" (multiplying
factor 0.1405) 300.69
TOTAL 2440.80 Y
Add 15% CPOH on "Y" 366.12
TOTAL 2806.91 Z
Add Cess @ 1% on "Z" 28.07
Cost of 100 metre 2834.98
Say 2835.00
18.81.11 500 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.098 1800.00 176.40
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0114 Beldar day 2.10 645.00 1354.50
9999 Sundries including testing of samples L.S. 23.27 2.12 49.33
TOTAL 2364.23 W
Add 1 % Water charges on "W" 23.64
TOTAL 2387.87 X
Add GST on "X" (multiplying
factor 0.1405) 335.50
TOTAL 2723.37 Y
Add 15% CPOH on "Y" 408.51
TOTAL 3131.88 Z
Add Cess @ 1% on "Z" 31.32
Cost of 100 metre 3163.20
Say 3163.20
18.81.12 600 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
1301 Bleaching powder quintal 0.141 1800.00 253.80
LABOUR
0116 Fitter (grade 1) day 1.20 784.00 940.80
0114 Beldar day 2.50 645.00 1612.50
SUB HEAD : 18- WATER SUPPLY 1669
Code Description Unit Quantity Rate Amount
9999 Sundries including testing of samples L.S. 26.00 2.12 55.12
TOTAL 2862.22 W
Add 1 % Water charges on "W" 28.62
TOTAL 2890.84 X
Add GST on "X" (multiplying
factor 0.1405) 406.16
TOTAL 3297.01 Y
Add 15% CPOH on "Y" 494.55
TOTAL 3791.56 Z
Add Cess @ 1% on "Z" 37.92
Cost of 100 metre 3829.47
Say 3829.45
18.82 Dismantling old C.I. pipes including excavation and refilling trenches after taking
out the pipes, breaking lead caulked joints, melting of lead and making into
blocks, including stacking of pipes at site lead up to 50 metre:
18.82.1 80 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x55x0.75 m=16.61 cum
Deduct for pipe 1x40.26x3.14/
4x(0.098)² =(-) 0.30 cum
Total= 16.31 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 16.31 286.85 4678.52 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 16.31 253.95 4141.92 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 0.373 500.00 186.50
0771 Kerosene oil litre 0.379 50.00 18.95
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 0.50 714.00 357.00
0114 Beldar day 4.00 645.00 2580.00
9988 Sundries and carriage L.S. 53.82 2.12 114.10
TOTAL 12077.00 W
Add 1 % Water charges on "W-A" 32.57
TOTAL 12109.56 X
Add GST on "X-A" (multiplying
factor 0.1405) 462.12
TOTAL 12571.68 Y
Add 15% CPOH on "Y-A" 562.69
TOTAL 13134.37 Z
Add Cess @ 1% on "Z-A" 43.14
Cost of 40.26 metre 13177.51
Cost of one metre 327.31
Say 327.30
SUB HEAD : 18- WATER SUPPLY 1670
18.82.2 100 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x55x0.75 m=16.61 cum
Deduct for pipe 1x40.26x3.14/
4x(0.118)² =(-) 0.44 cum
Total= 16.17 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 16.17 286.85 4638.36 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 16.17 253.95 4106.37 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 0.466 500.00 233.00
0771 Kerosene oil litre 0.379 50.00 18.95
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 0.63 714.00 449.82
0114 Beldar day 4.50 645.00 2902.50
9988 Sundries and carriage L.S. 53.82 2.12 114.10
TOTAL 12463.10 W
Add 1 % Water charges on "W-A" 37.18
TOTAL 12500.29 X
Add GST on "X-A" (multiplying
factor 0.1405) 527.66
TOTAL 13027.94 Y
Add 15% CPOH on "Y-A" 642.48
TOTAL 13670.42 Z
Add Cess @ 1% on "Z-A" 49.26
Cost of 40.26 metre 13719.68
Cost of one metre 340.78
Say 340.80
18.82.3 125 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x55x0.75 m=16.61 cum
Deduct for pipe 1x40.26x3.14/
4x(0.144)² =(-) 0.65 cum
Total= 15.96 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 15.96 286.85 4578.13 A
SUB HEAD : 18- WATER SUPPLY 1671
Code Description Unit Quantity Rate Amount
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 15.96 253.95 4053.04 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 0.559 500.00 279.50
0771 Kerosene oil litre 0.568 50.00 28.40
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 0.75 714.00 535.50
0114 Beldar day 5.00 645.00 3225.00
9988 Sundries and carriage L.S. 53.82 2.12 114.10
TOTAL 12813.67 W
Add 1 % Water charges on "W-A" 41.82
TOTAL 12855.49 X
Add GST on "X-A" (multiplying
factor 0.1405) 593.52
TOTAL 13449.01 Y
Add 15% CPOH on "Y-A" 722.68
TOTAL 14171.68 Z
Add Cess @ 1% on "Z-A" 55.41
Cost of 40.26 metre 14227.09
Cost of one metre 353.38
Say 353.40
18.82.4 150 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x55x0.75 m=16.61 cum
Deduct for pipe 1x40.26x3.14/
4x(0.17)² =(-) 0.91 cum
Total= 15.70 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 15.70 286.85 4503.55 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 15.70 253.95 3987.02 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 0.653 500.00 326.50
0771 Kerosene oil litre 0.568 50.00 28.40
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 0.88 714.00 628.32
0114 Beldar day 5.50 645.00 3547.50
SUB HEAD : 18- WATER SUPPLY 1672
Code Description Unit Quantity Rate Amount
9988 Sundries and carriage L.S. 67.21 2.12 142.49
TOTAL 13163.77 W
Add 1 % Water charges on "W-A" 46.73
TOTAL 13210.50 X
Add GST on "X-A" (multiplying
factor 0.1405) 663.15
TOTAL 13873.65 Y
Add 15% CPOH on "Y-A" 807.46
TOTAL 14681.11 Z
Add Cess @ 1% on "Z-A" 61.91
Cost of 40.26 metre 14743.02
Cost of one metre 366.20
Say 366.20
18.82.5 200 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x60x0.75 m=18.12 cum
Deduct for pipe 1x40.26x3.14/
4x(0.222)² =(-) 1.56 cum
Total= 16.56 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 16.56 286.85 4750.24 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 16.56 253.95 4205.41 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 0.84 500.00 420.00
0771 Kerosene oil litre 0.7576 50.00 37.88
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 1.10 714.00 785.40
0114 Beldar day 6.50 645.00 4192.50
9988 Sundries and carriage L.S. 67.21 2.12 142.49
TOTAL 14533.91 W
Add 1 % Water charges on "W-A" 55.78
TOTAL 14589.70 X
Add GST on "X-A" (multiplying
factor 0.1405) 791.58
TOTAL 15381.28 Y
Add 15% CPOH on "Y-A" 963.84
TOTAL 16345.12 Z
Add Cess @ 1% on "Z-A" 73.89
Cost of 40.26 metre 16419.02
Cost of one metre 407.82
Say 407.80
SUB HEAD : 18- WATER SUPPLY 1673
18.82.6 250 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.65x0.75 m=19.63 cum
Deduct for pipe 1x40.26x3.14/
4x(0.274)² =(-) 2.37 cum
Total= 17.26 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 17.26 286.85 4951.03 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 17.26 253.95 4383.18 A
Breaking lead caulked joints,
blocks and stacking
MATERIAL
0761 Fuel wood quintal 1.026 500.00 513.00
0771 Kerosene oil litre 1.1365 50.00 56.83
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 1.30 714.00 928.20
0114 Beldar day 7.50 645.00 4837.50
9988 Sundries and carriage L.S. 80.73 2.12 171.15
TOTAL 15840.88 W
Add 1 % Water charges on "W-A" 65.07
TOTAL 15905.95 X
Add GST on "X-A" (multiplying
factor 0.1405) 923.33
TOTAL 16829.28 Y
Add 15% CPOH on "Y-A" 1124.26
TOTAL 17953.54 Z
Add Cess @ 1% on "Z-A" 86.19
Cost of 40.26 metre 18039.73
Cost of one metre 448.08
Say 448.10
18.82.7 300 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.70x0.75 m=21.14 cum
Deduct for pipe 1x40.26x3.14/
4x(0.326)² =(-) 3.36 cum
Total= 17.79 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 17.79 286.85 5103.06 A
SUB HEAD : 18- WATER SUPPLY 1674
Code Description Unit Quantity Rate Amount
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 17.79 253.95 4517.77 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.12 500.00 560.00
0771 Kerosene oil litre 1.515 50.00 75.75
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 1.50 714.00 1071.00
0114 Beldar day 8.50 645.00 5482.50
9988 Sundries and carriage L.S. 94.12 2.12 199.53
TOTAL 17009.62 W
Add 1 % Water charges on "W-A" 73.89
TOTAL 17083.50 X
Add GST on "X-A" (multiplying
factor 0.1405) 1048.51
TOTAL 18132.01 Y
Add 15% CPOH on "Y-A" 1276.68
TOTAL 19408.69 Z
Add Cess @ 1% on "Z-A" 97.88
Cost of 40.26 metre 19506.56
Cost of one metre 484.51
Say 484.50
18.82.8 350 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.75x0.75 m=22.65 cum
Deduct for pipe 1x40.26x3.14/
4x(0.378)² =(-) 4.51 cum
Total= 18.14 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 18.14 286.85 5203.46 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 18.14 253.95 4606.65 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.213 500.00 606.50
0771 Kerosene oil litre 1.515 50.00 75.75
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 1.75 714.00 1249.50
0114 Beldar day 9.50 645.00 6127.50
SUB HEAD : 18- WATER SUPPLY 1675
Code Description Unit Quantity Rate Amount
9988 Sundries and carriage L.S. 107.64 2.12 228.20
TOTAL 18097.56 W
Add 1 % Water charges on "W-A" 82.87
TOTAL 18180.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 1176.03
TOTAL 19356.46 Y
Add 15% CPOH on "Y-A" 1431.95
TOTAL 20788.42 Z
Add Cess @ 1% on "Z-A" 109.78
Cost of 40.26 metre 20898.20
Cost of one metre 519.08
Say 519.10
18.82.9 400 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.80x0.75 m=24.16 cum
Deduct for pipe 1x40.26x3.14/
4x(0.429)² =(-) 5.93 cum
Total= 18.23 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 18.23 286.85 5229.28 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 18.23 253.95 4629.51 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.306 500.00 653.00
0771 Kerosene oil litre 1.894 50.00 94.70
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 2.00 714.00 1428.00
0114 Beldar day 10.50 645.00 6772.50
9988 Sundries and carriage L.S. 121.03 2.12 256.58
TOTAL 19063.57 W
Add 1 % Water charges on "W-A" 92.05
TOTAL 19155.62 X
Add GST on "X-A" (multiplying
factor 0.1405) 1306.20
TOTAL 20461.82 Y
Add 15% CPOH on "Y-A" 1590.46
TOTAL 22052.28 Z
Add Cess @ 1% on "Z-A" 121.93
Cost of 40.26 metre 22174.21
Cost of one metre 550.78
Say 550.80
SUB HEAD : 18- WATER SUPPLY 1676
18.82.10 450 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.85x0.75 m=25.67 cum
Deduct for pipe 1x40.26x3.14/
4x(0.48)² =(-) 7.29 cum
Total= 18.38 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 18.38 286.85 5272.30 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 18.38 253.95 4667.60 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.40 500.00 700.00
0771 Kerosene oil litre 2.273 50.00 113.65
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 2.25 714.00 1606.50
0114 Beldar day 11.50 645.00 7417.50
9988 Sundries and carriage L.S. 134.55 2.12 285.25
TOTAL 20062.80 W
Add 1 % Water charges on "W-A" 101.23
TOTAL 20164.03 X
Add GST on "X-A" (multiplying
factor 0.1405) 1436.49
TOTAL 21600.52 Y
Add 15% CPOH on "Y-A" 1749.09
TOTAL 23349.61 Z
Add Cess @ 1% on "Z-A" 134.10
Cost of 40.26 metre 23483.71
Cost of one metre 583.30
Say 583.30
18.82.11 500 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x.90x0.75 m=27.18 cum
Deduct for pipe 1x40.26x3.14/
4x(0.532)² =(-) 8.94 cum
Total= 18.24 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 18.24 286.85 5232.14 A
SUB HEAD : 18- WATER SUPPLY 1677
Code Description Unit Quantity Rate Amount
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 18.24 253.95 4632.05 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.492 500.00 746.00
0771 Kerosene oil litre 2.652 50.00 132.60
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 2.50 714.00 1785.00
0114 Beldar day 12.50 645.00 8062.50
9988 Sundries and carriage L.S. 147.94 2.12 313.63
TOTAL 20903.92 W
Add 1 % Water charges on "W-A" 110.40
TOTAL 21014.32 X
Add GST on "X-A" (multiplying
factor 0.1405) 1566.59
TOTAL 22580.92 Y
Add 15% CPOH on "Y-A" 1907.51
TOTAL 24488.42 Z
Add Cess @ 1% on "Z-A" 146.24
Cost of 40.26 metre 24634.67
Cost of one metre 611.89
Say 611.90
18.82.12 600 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 40.26 m or
11 nos. joints.
Earth work in excavation for
dismantling pipes including refilling of
excavated earth
1x40.26x1.00x0.75 m=30.20 cum
Deduct for pipe 1x40.26x3.14/
4x(0.635)² =(-) 12.76 cum
Total= 17.44 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 17.44 286.85 5002.66 A
2.25 (Rate as per item No.2.25 of
SH Earth work) cum 17.44 253.95 4428.89 A
Breaking lead caulked joints, blocks
and stacking
MATERIAL
0761 Fuel wood quintal 1.68 500.00 840.00
0771 Kerosene oil litre 3.41 50.00 170.50
LABOUR
0117 Assistant Fitter or 2nd class Fitter day 3.00 714.00 2142.00
0114 Beldar day 14.50 645.00 9352.50
SUB HEAD : 18- WATER SUPPLY 1678
Code Description Unit Quantity Rate Amount
9988 Sundries and carriage L.S. 174.85 2.12 370.68
TOTAL 22307.23 W
Add 1 % Water charges on "W-A" 128.76
TOTAL 22435.99 X
Add GST on "X-A" (multiplying
factor 0.1405) 1827.12
TOTAL 24263.11 Y
Add 15% CPOH on "Y-A" 2224.73
TOTAL 26487.85 Z
Add Cess @ 1% on "Z-A" 170.56
Cost of 40.26 metre 26658.41
Cost of one metre 662.16
Say 662.15
18.83 Labour for cutting C.I. pipe with steel saw.
18.83.1 80 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.06 784.00 47.04
0114 Beldar day 0.06 645.00 38.70
9999 Sundries L.S. 1.82 2.12 3.86
TOTAL 89.60 W
Add 1 % Water charges on "W" 0.90
TOTAL 90.49 X
Add GST on "X" (multiplying
factor 0.1405) 12.71
TOTAL 103.21 Y
Add 15% CPOH on "Y" 15.48
TOTAL 118.69 Z
Add Cess @ 1% on "Z" 1.19
Cost of each cut 119.88
Say 119.90
18.83.2 100 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.08 784.00 62.72
0114 Beldar day 0.08 645.00 51.60
9999 Sundries L.S. 2.73 2.12 5.79
TOTAL 120.11 W
Add 1 % Water charges on "W" 1.20
TOTAL 121.31 X
Add GST on "X" (multiplying
factor 0.1405) 17.04
TOTAL 138.35 Y
Add 15% CPOH on "Y" 20.75
TOTAL 159.11 Z
Add Cess @ 1% on "Z" 1.59
Cost of each cut 160.70
Say 160.70
SUB HEAD : 18- WATER SUPPLY 1679
18.83.3 125 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.11 784.00 86.24
0114 Beldar day 0.11 645.00 70.95
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 166.56 W
Add 1 % Water charges on "W" 1.67
TOTAL 168.23 X
Add GST on "X" (multiplying
factor 0.1405) 23.64
TOTAL 191.86 Y
Add 15% CPOH on "Y" 28.78
TOTAL 220.64 Z
Add Cess @ 1% on "Z" 2.21
Cost of each cut 222.85
Say 222.85
18.83.4 150 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.15 784.00 117.60
0114 Beldar day 0.15 645.00 96.75
9999 Sundries L.S. 5.33 2.12 11.30
TOTAL 225.65 W
Add 1 % Water charges on "W" 2.26
TOTAL 227.91 X
Add GST on "X" (multiplying
factor 0.1405) 32.02
TOTAL 259.93 Y
Add 15% CPOH on "Y" 38.99
TOTAL 298.92 Z
Add Cess @ 1% on "Z" 2.99
Cost of each cut 301.91
Say 301.90
18.83.5 200 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.20 784.00 156.80
0114 Beldar day 0.20 645.00 129.00
9999 Sundries L.S. 7.15 2.12 15.16
TOTAL 300.96 W
Add 1 % Water charges on "W" 3.01
TOTAL 303.97 X
Add GST on "X" (multiplying
factor 0.1405) 42.71
TOTAL 346.68 Y
Add 15% CPOH on "Y" 52.00
TOTAL 398.68 Z
Add Cess @ 1% on "Z" 3.99
Cost of each cut 402.66
Say 402.65
SUB HEAD : 18- WATER SUPPLY 1680
18.83.6 250 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.25 784.00 196.00
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 374.34 W
Add 1 % Water charges on "W" 3.74
TOTAL 378.08 X
Add GST on "X" (multiplying
factor 0.1405) 53.12
TOTAL 431.20 Y
Add 15% CPOH on "Y" 64.68
TOTAL 495.88 Z
Add Cess @ 1% on "Z" 4.96
Cost of each cut 500.84
Say 500.85
18.83.7 300 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.30 784.00 235.20
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 9.88 2.12 20.95
TOTAL 449.65 W
Add 1 % Water charges on "W" 4.50
TOTAL 454.14 X
Add GST on "X" (multiplying
factor 0.1405) 63.81
TOTAL 517.95 Y
Add 15% CPOH on "Y" 77.69
TOTAL 595.64 Z
Add Cess @ 1% on "Z" 5.96
Cost of each cut 601.60
Say 601.60
18.83.8 350 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.35 784.00 274.40
0114 Beldar day 0.35 645.00 225.75
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 523.02 W
Add 1 % Water charges on "W" 5.23
TOTAL 528.26 X
Add GST on "X" (multiplying
factor 0.1405) 74.22
TOTAL 602.47 Y
Add 15% CPOH on "Y" 90.37
TOTAL 692.85 Z
Add Cess @ 1% on "Z" 6.93
Cost of each cut 699.77
Say 699.75
SUB HEAD : 18- WATER SUPPLY 1681
18.83.9 400 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.40 784.00 313.60
0114 Beldar day 0.40 645.00 258.00
9999 Sundries L.S. 12.48 2.12 26.46
TOTAL 598.06 W
Add 1 % Water charges on "W" 5.98
TOTAL 604.04 X
Add GST on "X" (multiplying
factor 0.1405) 84.87
TOTAL 688.91 Y
Add 15% CPOH on "Y" 103.34
TOTAL 792.24 Z
Add Cess @ 1% on "Z" 7.92
Cost of each cut 800.16
Say 800.15
18.83.10 450 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.45 784.00 352.80
0114 Beldar day 0.45 645.00 290.25
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 671.71 W
Add 1 % Water charges on "W" 6.72
TOTAL 678.43 X
Add GST on "X" (multiplying
factor 0.1405) 95.32
TOTAL 773.75 Y
Add 15% CPOH on "Y" 116.06
TOTAL 889.81 Z
Add Cess @ 1% on "Z" 8.90
Cost of each cut 898.71
Say 898.70
18.83.11 500 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 15.21 2.12 32.25
TOTAL 746.75 W
Add 1 % Water charges on "W" 7.47
TOTAL 754.21 X
Add GST on "X" (multiplying
factor 0.1405) 105.97
TOTAL 860.18 Y
Add 15% CPOH on "Y" 129.03
TOTAL 989.21 Z
Add Cess @ 1% on "Z" 9.89
Cost of each cut 999.10
Say 999.10
SUB HEAD : 18- WATER SUPPLY 1682
18.83.12 600 mm diameter C.I. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for one cut.
LABOUR
0116 Fitter (grade 1) day 0.60 784.00 470.40
0114 Beldar day 0.60 645.00 387.00
9999 Sundries L.S. 16.12 2.12 34.17
TOTAL 891.57 W
Add 1 % Water charges on "W" 8.92
TOTAL 900.49 X
Add GST on "X" (multiplying
factor 0.1405) 126.52
TOTAL 1027.01 Y
Add 15% CPOH on "Y" 154.05
TOTAL 1181.06 Z
Add Cess @ 1% on "Z" 11.81
Cost of each cut 1192.87
Say 1192.85
18.84 Providing & fixing chrome plated brass battery based infrared sensor operated
pillar cock, having foam flow technology.
18.84.1 15 mm nominal bore
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
3327 15 mm Battery Based Sensor Pillar
Cock each 1.00 6000.00 6000.00
9988 Carriage of materials and fixing charges L.S. 8.06 2.12 17.09
TOTAL 6017.09 W
Add 1 % Water charges on "W" 60.17
TOTAL 6077.26 X
Add GST on "X" (multiplying
factor 0.1405) 853.85
TOTAL 6931.11 Y
Add 15% CPOH on "Y" 1039.67
TOTAL 7970.78 Z
Add Cess @ 1% on "Z" 79.71
Cost of one no. 8050.49
Say 8050.50
18.85 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS
standard 3448 complete with press type fitting (fitting shall be paid for separately)
i/c fixing of the pipe with clamps at 1.00 m spacing including cutting and making
good the walls including testing of joints complete as per direction of Engineer-
in-charge. (The pipe length inserted in the fitting shall not be measured for
payment)
Internal work - Exposed on wall
SUB HEAD : 18- WATER SUPPLY 1683
18.85.1 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8779 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
15.88 mm outer dia metre 10.00 140.00 1400.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00301 145.72 0.44
Add 3% for pipe inserted into fitting
and wastage etc. on P 42.00
3xP / 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
Add 2% for special T&P and sundries
etc. on P 28.00
2 xP / 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 2631.89 W
Add 1 % Water charges on "W" 26.32
TOTAL 2658.21 X
Add GST on "X" (multiplying
factor 0.1405) 373.48
TOTAL 3031.68 Y
Add 15% CPOH on "Y" 454.75
TOTAL 3486.44 Z
Add Cess @ 1% on "Z" 34.86
Cost of 10 metre 3521.30
Cost of 1 metre 352.13
Say 352.15
18.85.2 22.22 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8780 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
22.22 mm outer dia metre 10.00 250.00 2500.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00529 145.72 0.77
Add 3% for pipe inserted into fitting
and wastage etc. on P 75.00
3 xP/ 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
Add 2% for special T&P and sundries
etc. on P 50.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1684
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 3787.22 W
Add 1 % Water charges on "W" 37.87
TOTAL 3825.09 X
Add GST on "X" (multiplying
factor 0.1405) 537.43
TOTAL 4362.52 Y
Add 15% CPOH on "Y" 654.38
TOTAL 5016.89 Z
Add Cess @ 1% on "Z" 50.17
Cost of 10 metre 5067.06
Cost of 1 metre 506.71
Say 506.70
18.85.3 28.58 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8781 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
28.58 mm outer dia metre 10.00 310.00 3100.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00687 145.72 1.00
Add 3% for pipe inserted into fitting
and wastage etc. on P 93.00
3xP/ 100
9999 Cement, sand and grit L.S. 4.16 2.12 8.82
Add 2% for special T&P and sundries
etc. on P 62.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4420.48 W
Add 1 % Water charges on "W" 44.20
TOTAL 4464.69 X
Add GST on "X" (multiplying
factor 0.1405) 627.29
TOTAL 5091.97 Y
Add 15% CPOH on "Y" 763.80
TOTAL 5855.77 Z
Add Cess @ 1% on "Z" 58.56
Cost of 10 metre 5914.33
Cost of 1 metre 591.43
Say 591.45
SUB HEAD : 18- WATER SUPPLY 1685
18.85.4 34.00 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8782 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
34.00 mm outer dia metre 10.00 439.50 4395.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.0098 145.72 1.43
Add 3% for pipe inserted into fitting
and wastage etc. on P 131.85
3xP/ 100
9999 Cement, sand and grit L.S. 4.16 2.12 8.82
Add 2% for special T&P and sundries
etc. on P 87.90
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 5780.66 W
Add 1 % Water charges on "W" 57.81
TOTAL 5838.46 X
Add GST on "X" (multiplying
factor 0.1405) 820.30
TOTAL 6658.77 Y
Add 15% CPOH on "Y" 998.82
TOTAL 7657.58 Z
Add Cess @ 1% on "Z" 76.58
Cost of 10 metre 7734.16
Cost of 1 metre 773.42
Say 773.40
18.85.5 42.70 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8783 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
42.70 mm outer dia metre 10.00 450.00 4500.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.0124 145.72 1.81
Add 3% for pipe inserted into fitting
and wastage etc. on P 135.00
3xP/ 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
Add 2% for special T&P and sundries
etc. on P 90.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1686
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 5893.77 W
Add 1 % Water charges on "W" 58.94
TOTAL 5952.70 X
Add GST on "X" (multiplying
factor 0.1405) 836.35
TOTAL 6789.06 Y
Add 15% CPOH on "Y" 1018.36
TOTAL 7807.42 Z
Add Cess @ 1% on "Z" 78.07
Cost of 10 metre 7885.49
Cost of 1 metre 788.55
Say 788.55
18.85.6 48.60 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8701 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
48.60 mm outer dia metre 10.00 620.00 6200.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.0142 145.72 2.07
Add 3% for pipe inserted into fitting
and wastage etc. on P 186.00
3xP/ 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
Add 2% for special T&P and sundries
etc. on P 124.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 7679.03 W
Add 1 % Water charges on "W" 76.79
TOTAL 7755.82 X
Add GST on "X" (multiplying
factor 0.1405) 1089.69
TOTAL 8845.51 Y
Add 15% CPOH on "Y" 1326.83
TOTAL 10172.34 Z
Add Cess @ 1% on "Z" 101.72
Cost of 10 metre 10274.06
Cost of 1 metre 1027.41
Say 1027.40
SUB HEAD : 18- WATER SUPPLY 1687
18.85A Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS
6911:2017 and conforming to EN-10312 standards complete with press type
fitting (fitting shall be paid for separately) i/c fixing of the pipe with clamps at
1.00 m spacing including cutting and making good the walls including testing
of joints complete as per direction of Engineer-in-charge. (The pipe length
inserted in the fitting shall not be measured for payment)
Internal work - Exposed on wall
18.85A.1 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3862 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
15 mm outer dia metre 10.00 310.00 3100.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.003472 145.72 0.51
Add 3% for pipe inserted into fitting
and wastage etc. on P 93.00
3xP / 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
Add 2% for special T&P and sundries
etc. on P 62.00
2 xP / 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 4416.95 W
Add 1 % Water charges on "W" 44.17
TOTAL 4461.12 X
Add GST on "X" (multiplying
factor 0.1405) 626.79
TOTAL 5087.91 Y
Add 15% CPOH on "Y" 763.19
TOTAL 5851.10 Z
Add Cess @ 1% on "Z" 58.51
Cost of 10 metre 5909.61
Cost of 1 metre 590.96
Say 590.95
18.85A.2 22 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3863 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
22 mm outer dia metre 10.00 500.00 5000.00 P
SUB HEAD : 18- WATER SUPPLY 1688
Code Description Unit Quantity Rate Amount
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00619 145.72 0.90
Add 3% for pipe inserted into fitting
and wastage etc. on P 150.00
3 xP/ 100
9999 Cement, sand and grit L.S. 2.73 2.12 5.79
Add 2% for special T&P and sundries
etc. on P 100.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 6412.35 W
Add 1 % Water charges on "W" 64.12
TOTAL 6476.47 X
Add GST on "X" (multiplying
factor 0.1405) 909.94
TOTAL 7386.42 Y
Add 15% CPOH on "Y" 1107.96
TOTAL 8494.38 Z
Add Cess @ 1% on "Z" 84.94
Cost of 10 metre 8579.32
Cost of 1 metre 857.93
Say 857.95
18.85A.3 28 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3864 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
28 mm outer dia metre 10.00 650.00 6500.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00798 145.72 1.16
Add 3% for pipe inserted into fitting
and wastage etc. on P 195.00
3xP/ 100
9999 Cement, sand and grit L.S. 4.16 2.12 8.82
Add 2% for special T&P and sundries
etc. on P 130.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1689
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.70
TOTAL 7990.64 W
Add 1 % Water charges on "W" 79.91
TOTAL 8070.55 X
Add GST on "X" (multiplying
factor 0.1405) 1133.91
TOTAL 9204.46 Y
Add 15% CPOH on "Y" 1380.67
TOTAL 10585.13 Z
Add Cess @ 1% on "Z" 105.85
Cost of 10 metre 10690.98
Cost of 1 metre 1069.10
Say 1069.10
18.85A.4 35 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3865 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
35 mm outer dia metre 10.00 945.00 9450.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.01246 145.72 1.82
Add 3% for pipe inserted into fitting
and wastage etc. on P 283.50
3xP/ 100
9999 Cement, sand and grit L.S. 4.16 2.12 8.82
Add 2% for special T&P and sundries
etc. on P 189.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 11088.79 W
Add 1 % Water charges on "W" 110.89
TOTAL 11199.68 X
Add GST on "X" (multiplying
factor 0.1405) 1573.56
TOTAL 12773.24 Y
Add 15% CPOH on "Y" 1915.99
TOTAL 14689.22 Z
Add Cess @ 1% on "Z" 146.89
Cost of 10 metre 14836.12
Cost of 1 metre 1483.61
Say 1483.60
SUB HEAD : 18- WATER SUPPLY 1690
18.85A.5 42 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3866 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
42 mm outer dia metre 10.00 1160.00 11600.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.0151 145.72 2.20
Add 3% for pipe inserted into fitting
and wastage etc. on P 348.00
3xP/ 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
Add 2% for special T&P and sundries
etc. on P 232.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 13349.16 W
Add 1 % Water charges on "W" 133.49
TOTAL 13482.65 X
Add GST on "X" (multiplying
factor 0.1405) 1894.31
TOTAL 15376.96 Y
Add 15% CPOH on "Y" 2306.54
TOTAL 17683.51 Z
Add Cess @ 1% on "Z" 176.84
Cost of 10 metre 17860.34
Cost of 1 metre 1786.03
Say 1786.05
18.85A.6 54 mm outer dia Pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3867 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
54 mm outer dia metre 10.00 1500.00 15000.00 P
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.01953 145.72 2.85
Add 3% for pipe inserted into fitting
and wastage etc. on P 450.00
3xP/ 100
9999 Cement, sand and grit L.S. 5.33 2.12 11.30
Add 2% for special T&P and sundries
etc. on P 300.00
2xP/ 100
SUB HEAD : 18- WATER SUPPLY 1691
Code Description Unit Quantity Rate Amount
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.70
TOTAL 16919.81 W
Add 1 % Water charges on "W" 169.20
TOTAL 17089.00 X
Add GST on "X" (multiplying
factor 0.1405) 2401.01
TOTAL 19490.01 Y
Add 15% CPOH on "Y" 2923.50
TOTAL 22413.51 Z
Add Cess @ 1% on "Z" 224.14
Cost of 10 metre 22637.64
Cost of 1 metre 2263.76
Say 2263.75
18.86 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS
standard 3448 complete with press type fitting (fitting shall be paid for separately)
i/c fixing of the pipe with clamps at 1.00m spacing and also including cutting of
chases and making good the walls including testing of joints complete as per
direction of Engineer -in-charge. (The pipe length inserted in the fitting shall
not be measured for payment)
Internal work - Concealed Pipe
18.86.1 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8779 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
15.88 mm outer dia metre 10.00 140.00 1400.00 P
Add 3% for pipe inserted into fitting
and wastage etc. on P 42.00
3xP/ 100
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00301 145.72 0.44
Making chases upto 7.5x7.5 cm.in
walls and making good the same
18.78 Rate as per Item No.18.78 of
SH:WATER SUPPLY metre 10.00 171.80 1718 A
Add 2% for special T&P and sundries
etc. on P 28.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
SUB HEAD : 18- WATER SUPPLY 1692
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.66 645.00 425.7
TOTAL 4344.10 W
Add 1 % Water charges on "W-A" 26.26
TOTAL 4370.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 372.66
TOTAL 4743.02 Y
Add 15% CPOH on "Y-A" 453.75
TOTAL 5196.77 Z
Add Cess @ 1% on "Z-A" 34.79
Cost of 10 metre 5231.56
Cost of 1 metre 523.16
Say 523.15
18.86.2 22.22 mm Outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
8780 SS pipe 304 grades with press fit
technology as per JIS 3448 standard
22.22 mm outer dia metre 10.00 250.00 2500.00 P
Add 3% for pipe inserted into fitting
and wastage etc. on P 75.00
3xP/ 100
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00529 145.72 0.77
Making chases upto 7.5x7.5 cm.in
walls and making good the same
18.78 Rate as per Item No.18.78 of
SH: WATER SUPPLY metre 10.00 171.80 1718 A
Add 2% for special T&P and sundries
etc. on P 50.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.7
TOTAL 5499.43 W
Add 1 % Water charges on "W-A" 37.81
TOTAL 5537.25 X
Add GST on "X-A" (multiplying
factor 0.1405) 536.60
TOTAL 6073.85 Y
Add 15% CPOH on "Y-A" 653.38
TOTAL 6727.23 Z
Add Cess @ 1% on "Z-A" 50.09
Cost of 10 metre 6777.32
Cost of 1 metre 677.73
Say 677.75
SUB HEAD : 18- WATER SUPPLY 1693
18.86A Providing and fixing Stainless Steel pipe and fitting of grade 316L as per IS
6911:2017 and conforming to EN-10312 standards complete with press type
fitting (fitting shall be paid for separately) i/c fixing of the pipe with clamps at
1.00m spacing and also including cutting of chases and making good the walls
including testing of joints complete as per direction of Engineer -in-charge.
(The pipe length inserted in the fitting shall not be measured for payment)
Internal work - Concealed Pipe
18.86A.1 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3862 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
15 mm outer dia metre 10.00 310.00 3100.00 P
Add 3% for pipe inserted into fitting
and wastage etc. on P . 93.00
3xP/ 100
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.003472 145.72 0.51
Making chases upto 7.5x7.5 cm.in
walls and making good the same
18.78 Rate as per Item No.18.78 of
SH:WATER SUPPLY metre 10.00 171.80 1718 A
Add 2% for special T&P and sundries
etc. on P 62.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.7
TOTAL 6129.17 W
Add 1 % Water charges on "W-A" 44.11
TOTAL 6173.28 X
Add GST on "X" (multiplying
factor 0.1405) 625.97
TOTAL 6799.24 Y
Add 15% CPOH on "Y-A" 762.19
TOTAL 7561.43 Z
Add Cess @ 1% on "Z-A" 58.43
Cost of 10 metre 7619.87
Cost of 1 metre 761.99
Say 762.00
18.86A.2 22 mm Outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
3863 SS pipe 316L grade as per IS
6911:2017 with press fit technology
conforming to EN-10312 standards
22 mm outer dia metre 10.00 500.00 5000.00 P
SUB HEAD : 18- WATER SUPPLY 1694
Code Description Unit Quantity Rate Amount
Add 3% for pipe inserted into fitting
and wastage etc. on P 150.00
3xP/ 100
2272 Carriage of Stainless Steel pipes
below 100 mm dia tonne 0.00619 145.72 0.90
Making chases upto 7.5x7.5 cm.
in walls and making good the same
18.78 Rate as per Item No.18.78 of
SH: WATER SUPPLY metre 10.00 171.80 1718 A
Add 2% for special T&P and sundries
etc. on P 100.00
2xP/ 100
LABOUR
0116 Fitter (grade 1) day 0.33 784.00 258.72
0117 Assistant Fitter or 2nd class Fitter day 0.66 714.00 471.24
0114 Beldar day 0.66 645.00 425.7
TOTAL 8124.56 W
Add 1 % Water charges on "W-A" 64.07
TOTAL 8188.63 X
Add GST on "X" (multiplying
factor 0.1405) 909.12
TOTAL 9097.75 Y
Add 15% CPOH on "Y-A" 1106.96
TOTAL 10204.71 Z
Add Cess @ 1% on "Z-A" 84.87
Cost of 10 metre 10289.58
Cost of 1 metre 1028.96
Say 1028.95
18.87 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Coupling/Socket
18.87.1 For 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8702 Coupling/Socket fittings for 15.88 mm
outer dia SS pipe each 1.00 60.00 60.00
TOTAL 60.00 W
Add 1 % Water charges on "W" 0.60
TOTAL 60.60 X
Add GST on "X" (multiplying
factor 0.1405) 8.51
TOTAL 69.11 Y
Add 15% CPOH on "Y" 10.37
TOTAL 79.48 Z
Add Cess @ 1% on "Z" 0.79
Cost of 1 no. 80.28
Say 80.30
SUB HEAD : 18- WATER SUPPLY 1695
18.87.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8786 Coupling/Socket fittings for 22.22 mm
outer dia SS pipe each 1.00 70.00 70.00
TOTAL 70.00 W
Add 1 % Water charges on "W" 0.70
TOTAL 70.70 X
Add GST on "X" (multiplying
factor 0.1405) 9.93
TOTAL 80.63 Y
Add 15% CPOH on "Y" 12.10
TOTAL 92.73 Z
Add Cess @ 1% on "Z" 0.93
Cost of 1 no. 93.66
Say 93.65
18.87.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8787 Coupling/Socket fittings for 28.58 mm
outer dia SS pipe each 1.00 96.25 96.25
TOTAL 96.25 W
Add 1 % Water charges on "W" 0.96
TOTAL 97.21 X
Add GST on "X" (multiplying
factor 0.1405) 13.66
TOTAL 110.87 Y
Add 15% CPOH on "Y" 16.63
TOTAL 127.50 Z
Add Cess @ 1% on "Z" 1.28
Cost of 1 no. 128.78
Say 128.80
18.87.4 For 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8788 Coupling/Socket fittings for 34.00 mm
outer dia SS pipe each 1.00 135.00 135.00
TOTAL 135.00 W
Add 1 % Water charges on "W" 1.35
TOTAL 136.35 X
Add GST on "X" (multiplying
factor 0.1405) 19.16
TOTAL 155.51 Y
Add 15% CPOH on "Y" 23.33
TOTAL 178.83 Z
Add Cess @ 1% on "Z" 1.79
Cost of 1 no. 180.62
Say 180.60
SUB HEAD : 18- WATER SUPPLY 1696
18.87.5 For 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8789 Coupling/Socket fittings for 42.70 mm
outer dia SS pipe each 1.00 160.00 160.00
TOTAL 160.00 W
Add 1 % Water charges on "W" 1.60
TOTAL 161.60 X
Add GST on "X" (multiplying
factor 0.1405) 22.70
TOTAL 184.30 Y
Add 15% CPOH on "Y" 27.65
TOTAL 211.95 Z
Add Cess @ 1% on "Z" 2.12
Cost of 1 no. 214.07
Say 214.05
18.87.6 For 48.60 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8790 Coupling/Socket fittings for 48.60 mm
outer dia SS pipe each 1.00 180.00 180.00
TOTAL 180.00 W
Add 1 % Water charges on "W" 1.80
TOTAL 181.80 X
Add GST on "X" (multiplying
factor 0.1405) 25.54
TOTAL 207.34 Y
Add 15% CPOH on "Y" 31.10
TOTAL 238.44 Z
Add Cess @ 1% on "Z" 2.38
Cost of 1 no. 240.83
Say 240.85
18.87A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Coupling/Socket
18.87A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
SUB HEAD : 18- WATER SUPPLY 1697
Code Description Unit Quantity Rate Amount
3868 Coupling/Socket fittings for 15 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 215.00 215.00
TOTAL 215.00 W
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost of 1 no. 287.66
Say 287.65
18.87A.2 For 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3869 Coupling/Socket fittings for 22 mm
outer dia SS pipe of grade 316 L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 270.00 270.00
TOTAL 270.00 W
Add 1 % Water charges on "W" 2.70
TOTAL 272.70 X
Add GST on "X" (multiplying
factor 0.1405) 38.31
TOTAL 311.01 Y
Add 15% CPOH on "Y" 46.65
TOTAL 357.67 Z
Add Cess @ 1% on "Z" 3.58
Cost of 1 no. 361.24
Say 361.25
18.87A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3870 Coupling/Socket fittings for 28 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to EN-
10312 each 1.00 315.00 315.00
TOTAL 315.00 W
Add 1 % Water charges on "W" 3.15
TOTAL 318.15 X
Add GST on "X" (multiplying
factor 0.1405) 44.70
TOTAL 362.85 Y
Add 15% CPOH on "Y" 54.43
TOTAL 417.28 Z
Add Cess @ 1% on "Z" 4.17
Cost of 1 no. 421.45
Say 421.45
SUB HEAD : 18- WATER SUPPLY 1698
18.87A.4 For 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3871 Coupling/Socket fittings for 35 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to EN-
10312 each 1.00 395.00 395.00
TOTAL 395.00 W
Add 1 % Water charges on "W" 3.95
TOTAL 398.95 X
Add GST on "X" (multiplying
factor 0.1405) 56.05
TOTAL 455.00 Y
Add 15% CPOH on "Y" 68.25
TOTAL 523.25 Z
Add Cess @ 1% on "Z" 5.23
Cost of 1 no. 528.49
Say 528.50
18.87A.5 For 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3872 Coupling/Socket fittings for 42 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to EN-
10312 each 1.00 535.00 535.00
TOTAL 535.00 W
Add 1 % Water charges on "W" 5.35
TOTAL 540.35 X
Add GST on "X" (multiplying
factor 0.1405) 75.92
TOTAL 616.27 Y
Add 15% CPOH on "Y" 92.44
TOTAL 708.71 Z
Add Cess @ 1% on "Z" 7.09
Cost of 1 no. 715.80
Say 715.80
SUB HEAD : 18- WATER SUPPLY 1699
18.87A.6 For 54 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3873 Coupling/Socket fittings for 54 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 640.00 640.00
TOTAL 640.00 W
Add 1 % Water charges on "W" 6.40
TOTAL 646.40 X
Add GST on "X" (multiplying
factor 0.1405) 90.82
TOTAL 737.22 Y
Add 15% CPOH on "Y" 110.58
TOTAL 847.80 Z
Add Cess @ 1% on "Z" 8.48
Cost of 1 no. 856.28
Say 856.30
18.88 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of providing and fixing required
Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA
G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM
material of required dia as per dirction of Engineer-in-charge.
Reducer
18.88.1 For 22.22 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8791 Reducer for 22.22 mm X 15.88 mm
outer Dia SS pipe each 1.00 108.50 108.50
TOTAL 108.50 W
Add 1 % Water charges on "W" 1.09
TOTAL 109.59 X
Add GST on "X" (multiplying
factor 0.1405) 15.40
TOTAL 124.98 Y
Add 15% CPOH on "Y" 18.75
TOTAL 143.73 Z
Add Cess @ 1% on "Z" 1.44
Cost of 1 no. 145.17
Say 145.15
SUB HEAD : 18- WATER SUPPLY 1700
18.88.2 For 28.58 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8792 Reducer for 28.58 mm X 15.88 mm
outer Dia SS pipe each 1.00 152.50 152.50
TOTAL 152.50 W
Add 1 % Water charges on "W" 1.53
TOTAL 154.03 X
Add GST on "X" (multiplying
factor 0.1405) 21.64
TOTAL 175.67 Y
Add 15% CPOH on "Y" 26.35
TOTAL 202.02 Z
Add Cess @ 1% on "Z" 2.02
Cost of 1 no. 204.04
Say 204.05
18.88.3 For 28.58 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8793 Reducer for 28.58 mm X 22.22 mm
outer Dia SS pipe each 1.00 161.50 161.50
TOTAL 161.50 W
Add 1 % Water charges on "W" 1.62
TOTAL 163.12 X
Add GST on "X" (multiplying
factor 0.1405) 22.92
TOTAL 186.03 Y
Add 15% CPOH on "Y" 27.90
TOTAL 213.94 Z
Add Cess @ 1% on "Z" 2.14
Cost of 1 no. 216.08
Say 216.10
18.88.4 For 34.00 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8794 Reducer for 34.00 mm X 15.88 mm
outer Dia SS pipe each 1.00 200.00 200.00
TOTAL 200.00 W
Add 1 % Water charges on "W" 2.00
TOTAL 202.00 X
Add GST on "X" (multiplying
factor 0.1405) 28.38
TOTAL 230.38 Y
Add 15% CPOH on "Y" 34.56
TOTAL 264.94 Z
Add Cess @ 1% on "Z" 2.65
Cost of 1 no. 267.59
Say 267.60
SUB HEAD : 18- WATER SUPPLY 1701
18.88.5 For 34.00 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8795 Reducer for 34.00 mm X 22.22 mm
outer Dia SS pipe each 1.00 210.00 210.00
TOTAL 210.00 W
Add 1 % Water charges on "W" 2.10
TOTAL 212.10 X
Add GST on "X" (multiplying
factor 0.1405) 29.80
TOTAL 241.90 Y
Add 15% CPOH on "Y" 36.29
TOTAL 278.19 Z
Add Cess @ 1% on "Z" 2.78
Cost of 1 no. 280.97
Say 280.95
18.88.6 For 34.00 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8796 Reducer for 34.00 mm X 28.58 mm
outer Dia SS pipe each 1.00 210.00 210.00
TOTAL 210.00 W
Add 1 % Water charges on "W" 2.10
TOTAL 212.10 X
Add GST on "X" (multiplying
factor 0.1405) 29.80
TOTAL 241.90 Y
Add 15% CPOH on "Y" 36.29
TOTAL 278.19 Z
Add Cess @ 1% on "Z" 2.78
Cost of 1 no. 280.97
Say 280.95
18.88.7 For 42.70 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8797 Reducer for 42.70 mm X 15.88 mm
outer Dia SS pipe each 1.00 375.00 375.00
TOTAL 375.00 W
Add 1 % Water charges on "W" 3.75
TOTAL 378.75 X
Add GST on "X" (multiplying
factor 0.1405) 53.21
TOTAL 431.96 Y
Add 15% CPOH on "Y" 64.79
TOTAL 496.76 Z
Add Cess @ 1% on "Z" 4.97
Cost of 1 no. 501.73
Say 501.75
SUB HEAD : 18- WATER SUPPLY 1702
18.88.8 For 42.70 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8798 Reducer for 42.70 mm X 22.22 mm
outer Dia SS pipe each 1.00 375.00 375.00
TOTAL 375.00 W
Add 1 % Water charges on "W" 3.75
TOTAL 378.75 X
Add GST on "X" (multiplying
factor 0.1405) 53.21
TOTAL 431.96 Y
Add 15% CPOH on "Y" 64.79
TOTAL 496.76 Z
Add Cess @ 1% on "Z" 4.97
Cost of 1 no. 501.73
Say 501.75
18.88.9 For 42.70 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8799 Reducer for 42.70 mm X 28.58 mm
outer Dia SS pipe each 1.00 390.00 390.00
TOTAL 390.00 W
Add 1 % Water charges on "W" 3.90
TOTAL 393.90 X
Add GST on "X" (multiplying
factor 0.1405) 55.34
TOTAL 449.24 Y
Add 15% CPOH on "Y" 67.39
TOTAL 516.63 Z
Add Cess @ 1% on "Z" 5.17
Cost of 1 no. 521.80
Say 521.80
18.88.10 For 42.70 mm x 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8800 Reducer for 42.70 mm X 34.00 mm
outer Dia SS pipe each 1.00 390.00 390.00
TOTAL 390.00 W
Add 1 % Water charges on "W" 3.90
TOTAL 393.90 X
Add GST on "X" (multiplying
factor 0.1405) 55.34
TOTAL 449.24 Y
Add 15% CPOH on "Y" 67.39
TOTAL 516.63 Z
Add Cess @ 1% on "Z" 5.17
Cost of 1 no. 521.80
Say 521.80
SUB HEAD : 18- WATER SUPPLY 1703
18.88.11 For 48.60 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8801 Reducer for 48.60 mm X 15.88 mm
outer Dia SS pipe each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
18.88.12 For 48.60 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8802 Reducer for 48.60 mm X 22.22 mm
outer Dia SS pipe each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
18.88.13 For 48.60 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8803 Reducer for 48.60 mm X 28.58 mm
outer Dia SS pipe each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
SUB HEAD : 18- WATER SUPPLY 1704
18.88.14 For 48.60 mm x 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8804 Reducer for 48.60 mm X 34.00 mm
outer Dia SS pipe each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
18.88.15 For 48.60 mm x 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8805 Reducer for48.60 mm X 42.70 mm
outer Dia SS pipe each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
18.88A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per dirction
of Engineer-in-charge.
Reducer
18.88A.1 For 22mm x 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3874 Reducer for 22mm x 15 mm outer Dia
SS pipe of grade 316L as per IS
6911:2017 and conforming to EN-
10312 each 1.00 255.00 255.00
TOTAL 255.00 W
SUB HEAD : 18- WATER SUPPLY 1705
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 2.55
TOTAL 257.55 X
Add GST on "X" (multiplying
factor 0.1405) 36.19
TOTAL 293.74 Y
Add 15% CPOH on "Y" 44.06
TOTAL 337.80 Z
Add Cess @ 1% on "Z" 3.38
Cost of 1 no. 341.17
Say 341.15
18.88A.2 For 28 mm x 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3875 Reducer for 28 mm X 15 mm outer Dia
SS pipe of grade 316L as per IS
6911:2017 and conforming to EN-
10312 each 1.00 310.00 310.00
TOTAL 310.00 W
Add 1 % Water charges on "W" 3.10
TOTAL 313.10 X
Add GST on "X" (multiplying
factor 0.1405) 43.99
TOTAL 357.09 Y
Add 15% CPOH on "Y" 53.56
TOTAL 410.65 Z
Add Cess @ 1% on "Z" 4.11
Cost of 1 no. 414.76
Say 414.75
18.88A.3 For 28 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3876 Reducer for 28 mm x 22 mm outer Dia
SS pipe of grade 316L as per IS
6911:2017 and conforming to EN-
10312 each 1.00 375.00 375.00
TOTAL 375.00 W
Add 1 % Water charges on "W" 3.75
TOTAL 378.75 X
Add GST on "X" (multiplying
factor 0.1405) 53.21
TOTAL 431.96 Y
Add 15% CPOH on "Y" 64.79
TOTAL 496.76 Z
Add Cess @ 1% on "Z" 4.97
Cost of 1 no. 501.73
Say 501.75
SUB HEAD : 18- WATER SUPPLY 1706
18.88A.4 For 35 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3877 Reducer for 35 mm x 22 mm outer Dia
SS pipe of grade 316L as per IS
6911:2017 and conforming to EN-
10312 each 1.00 380.00 380.00
TOTAL 380.00 W
Add 1 % Water charges on "W" 3.80
TOTAL 383.80 X
Add GST on "X" (multiplying
factor 0.1405) 53.92
TOTAL 437.72 Y
Add 15% CPOH on "Y" 65.66
TOTAL 503.38 Z
Add Cess @ 1% on "Z" 5.03
Cost of 1 no. 508.42
Say 508.40
18.88A.5 For 35 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3878 Reducer for 35 mm x 28 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 470.00 470.00
TOTAL 470.00 W
Add 1 % Water charges on "W" 4.70
TOTAL 474.70 X
Add GST on "X" (multiplying
factor 0.1405) 66.70
TOTAL 541.40 Y
Add 15% CPOH on "Y" 81.21
TOTAL 622.60 Z
Add Cess @ 1% on "Z" 6.23
Cost of 1 no. 628.83
Say 628.85
18.88A.6 For 42 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3879 Reducer for 42 mm x 22 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 605.00 605.00
TOTAL 605.00 W
SUB HEAD : 18- WATER SUPPLY 1707
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 6.05
TOTAL 611.05 X
Add GST on "X" (multiplying
factor 0.1405) 85.85
TOTAL 696.90 Y
Add 15% CPOH on "Y" 104.54
TOTAL 801.44 Z
Add Cess @ 1% on "Z" 8.01
Cost of 1 no. 809.45
Say 809.45
18.88A.7 For 42 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3880 Reducer for 42 mm x 28 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.03 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
18.88A.8 For 42 mm x 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3881 Reducer for 42 mm x 35 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 720.00 720.00
TOTAL 720.00 W
Add 1 % Water charges on "W" 7.20
TOTAL 727.20 X
Add GST on "X" (multiplying
factor 0.1405) 102.17
TOTAL 829.37 Y
Add 15% CPOH on "Y" 124.41
TOTAL 953.78 Z
Add Cess @ 1% on "Z" 9.54
Cost of 1 no. 963.32
Say 963.30
SUB HEAD : 18- WATER SUPPLY 1708
18.88A.9 For 54 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3882 Reducer for 54 mm x 28 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 835.00 835.00
TOTAL 835.00 W
Add 1 % Water charges on "W" 8.35
TOTAL 843.35 X
Add GST on "X" (multiplying
factor 0.1405) 118.49
TOTAL 961.84 Y
Add 15% CPOH on "Y" 144.28
TOTAL 1106.12 Z
Add Cess @ 1% on "Z" 11.06
Cost of 1 no. 1117.18
Say 1117.20
18.88A.10 For 54 mm x 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3883 Reducer for 54 mm x 35 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 990.00 990.00
TOTAL 990.00 W
Add 1 % Water charges on "W" 9.90
TOTAL 999.90 X
Add GST on "X" (multiplying
factor 0.1405) 140.49
TOTAL 1140.39 Y
Add 15% CPOH on "Y" 171.06
TOTAL 1311.44 Z
Add Cess @ 1% on "Z" 13.11
Cost of 1 no. 1324.56
Say 1324.55
18.88A.11 For 54 mm x 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3884 Reducer for 54 mm x 42 mm outer Dia
SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1030.00 1030.00
TOTAL 1030.00 W
Add 1 % Water charges on "W" 10.30
SUB HEAD : 18- WATER SUPPLY 1709
Code Description Unit Quantity Rate Amount
TOTAL 1040.30 X
Add GST on "X" (multiplying
factor 0.1405) 146.16
TOTAL 1186.46 Y
Add 15% CPOH on "Y" 177.97
TOTAL 1364.43 Z
Add Cess @ 1% on "Z" 13.64
Cost of 1 no. 1378.08
Say 1378.10
18.89 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Slip Coupling/ Socket
18.89.1 For 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8806 Slip Coupling / Socket 15.88 mm
outer dia SS pipe each 1.00 55.00 55.00
TOTAL 55.00 W
Add 1 % Water charges on "W" 0.55
TOTAL 55.55 X
Add GST on "X" (multiplying
factor 0.1405) 7.80
TOTAL 63.35 Y
Add 15% CPOH on "Y" 9.50
TOTAL 72.86 Z
Add Cess @ 1% on "Z" 0.73
Cost of 1 no. 73.59
Say 73.60
18.89.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8807 Slip Coupling / Socket 22.22 mm
outer dia SS pipe each 1.00 70.00 70.00
TOTAL 70.00 W
Add 1 % Water charges on "W" 0.70
TOTAL 70.70 X
Add GST on "X" (multiplying
factor 0.1405) 9.93
TOTAL 80.63 Y
Add 15% CPOH on "Y" 12.10
TOTAL 92.73 Z
Add Cess @ 1% on "Z" 0.93
Cost of 1 no. 93.66
Say 93.65
SUB HEAD : 18- WATER SUPPLY 1710
18.89.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8808 Slip Coupling / Socket 28.58 mm
outer dia SS pipe each 1.00 95.00 95.00
TOTAL 95.00 W
Add 1 % Water charges on "W" 0.95
TOTAL 95.95 X
Add GST on "X" (multiplying
factor 0.1405) 13.48
TOTAL 109.43 Y
Add 15% CPOH on "Y" 16.41
TOTAL 125.85 Z
Add Cess @ 1% on "Z" 1.26
Cost of 1 no. 127.10
Say 127.10
18.89.4 For 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8809 Slip Coupling / Socket 34.00 mm
outer dia SS pipe each 1.00 135.00 135.00
TOTAL 135.00 W
Add 1 % Water charges on "W" 1.35
TOTAL 136.35 X
Add GST on "X" (multiplying
factor 0.1405) 19.16
TOTAL 155.51 Y
Add 15% CPOH on "Y" 23.33
TOTAL 178.83 Z
Add Cess @ 1% on "Z" 1.79
Cost of 1 no. 180.62
Say 180.60
18.89.5 For 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8810 Slip Coupling / Socket 42.70 mm
outer dia SS pipe each 1.00 160.00 160.00
TOTAL 160.00 W
Add 1 % Water charges on "W" 1.60
TOTAL 161.60 X
Add GST on "X" (multiplying
factor 0.1405) 22.70
TOTAL 184.30 Y
Add 15% CPOH on "Y" 27.65
TOTAL 211.95 Z
Add Cess @ 1% on "Z" 2.12
Cost of 1 no. 214.07
Say 214.05
SUB HEAD : 18- WATER SUPPLY 1711
18.89.6 For 48.60 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8811 Slip Coupling / Socket 48.60 mm
outer dia SS pipe each 1.00 175.00 175.00
TOTAL 175.00 W
Add 1 % Water charges on "W" 1.75
TOTAL 176.75 X
Add GST on "X" (multiplying
factor 0.1405) 24.83
TOTAL 201.58 Y
Add 15% CPOH on "Y" 30.24
TOTAL 231.82 Z
Add Cess @ 1% on "Z" 2.32
Cost of 1 no. 234.14
Say 234.15
18.89A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Sleeve/Slip Coupling/ Socket
18.89A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3885 Sleeve/ Slip Coupling / Socket 15 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 375.00 375.00
TOTAL 375.00 W
Add 1 % Water charges on "W" 3.75
TOTAL 378.75 X
Add GST on "X" (multiplying
factor 0.1405) 53.21
TOTAL 431.96 Y
Add 15% CPOH on "Y" 64.79
TOTAL 496.76 Z
Add Cess @ 1% on "Z" 4.97
Cost of 1 no. 501.73
Say 501.75
SUB HEAD : 18- WATER SUPPLY 1712
18.89A.2 For 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3886 Sleeve/ Slip Coupling / Socket 22 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 450.00 450.00
TOTAL 450.00 W
Add 1 % Water charges on "W" 4.50
TOTAL 454.50 X
Add GST on "X" (multiplying
factor 0.1405) 63.86
TOTAL 518.36 Y
Add 15% CPOH on "Y" 77.75
TOTAL 596.11 Z
Add Cess @ 1% on "Z" 5.96
Cost of 1 no. 602.07
Say 602.05
18.89A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3887 Sleeve/ Slip Coupling / Socket 28 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 520.00 520.00
TOTAL 520.00 W
Add 1 % Water charges on "W" 5.20
TOTAL 525.20 X
Add GST on "X" (multiplying
factor 0.1405) 73.79
TOTAL 598.99 Y
Add 15% CPOH on "Y" 89.85
TOTAL 688.84 Z
Add Cess @ 1% on "Z" 6.89
Cost of 1 no. 695.73
Say 695.75
18.89A.4 For 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3888 Sleeve/ Slip Coupling / Socket 35 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 580.00 580.00
TOTAL 580.00 W
Add 1 % Water charges on "W" 5.80
SUB HEAD : 18- WATER SUPPLY 1713
Code Description Unit Quantity Rate Amount
TOTAL 585.80 X
Add GST on "X" (multiplying
factor 0.1405) 82.30
TOTAL 668.10 Y
Add 15% CPOH on "Y" 100.22
TOTAL 768.32 Z
Add Cess @ 1% on "Z" 7.68
Cost of 1 no. 776.00
Say 776.00
18.89A.5 For 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3889 Sleeve/ Slip Coupling / Socket 42 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 670.00 670.00
TOTAL 670.00 W
Add 1 % Water charges on "W" 6.70
TOTAL 676.70 X
Add GST on "X" (multiplying
factor 0.1405) 95.08
TOTAL 771.78 Y
Add 15% CPOH on "Y" 115.77
TOTAL 887.54 Z
Add Cess @ 1% on "Z" 8.88
Cost of 1 no. 896.42
Say 896.40
18.89A.6 For 54 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3890 Sleeve/ Slip Coupling / Socket 54 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 955.00 955.00
TOTAL 955.00 W
Add 1 % Water charges on "W" 9.55
TOTAL 964.55 X
Add GST on "X" (multiplying
factor 0.1405) 135.52
TOTAL 1100.07 Y
Add 15% CPOH on "Y" 165.01
TOTAL 1265.08 Z
Add Cess @ 1% on "Z" 12.65
Cost of 1 no. 1277.73
Say 1277.75
SUB HEAD : 18- WATER SUPPLY 1714
18.90 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Elbow 90°
18.90.1 For 15.88mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8812 Elbow 90° for 15.88 mm outer dia
SS pipe each 1.00 65.00 65.00
TOTAL 65.00 W
Add 1 % Water charges on "W" 0.65
TOTAL 65.65 X
Add GST on "X" (multiplying
factor 0.1405) 9.22
TOTAL 74.87 Y
Add 15% CPOH on "Y" 11.23
TOTAL 86.10 Z
Add Cess @ 1% on "Z" 0.86
Cost of 1 no. 86.97
Say 86.95
18.90.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8813 Elbow 90° for 22.22 mm outer dia
SS pipe each 1.00 70.00 70.00
TOTAL 70.00 W
Add 1 % Water charges on "W" 0.70
TOTAL 70.70 X
Add GST on "X" (multiplying
factor 0.1405) 9.93
TOTAL 80.63 Y
Add 15% CPOH on "Y" 12.10
TOTAL 92.73 Z
Add Cess @ 1% on "Z" 0.93
Cost of 1 no. 93.66
Say 93.65
18.90.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
SUB HEAD : 18- WATER SUPPLY 1715
Code Description Unit Quantity Rate Amount
8814 Elbow 90° for 28.58 mm outer dia
SS pipe each 1.00 105.00 105.00
TOTAL 105.00 W
Add 1 % Water charges on "W" 1.05
TOTAL 106.05 X
Add GST on "X" (multiplying
factor 0.1405) 14.90
TOTAL 120.95 Y
Add 15% CPOH on "Y" 18.14
TOTAL 139.09 Z
Add Cess @ 1% on "Z" 1.39
Cost of 1 no. 140.48
Say 140.50
18.90.4 For 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8815 Elbow 90° for 34.00 mm outer dia SS pipe each 1.00 120.00 120.00
TOTAL 120.00 W
Add 1 % Water charges on "W" 1.20
TOTAL 121.20 X
Add GST on "X" (multiplying
factor 0.1405) 17.03
TOTAL 138.23 Y
Add 15% CPOH on "Y" 20.73
TOTAL 158.96 Z
Add Cess @ 1% on "Z" 1.59
Cost of 1 no. 160.55
Say 160.55
18.90.5 For 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8816 Elbow 90° for 42.70 mm outer dia
SS pipe each 1.00 130.00 130.00
TOTAL 130.00 W
Add 1 % Water charges on "W" 1.30
TOTAL 131.30 X
Add GST on "X" (multiplying
factor 0.1405) 18.45
TOTAL 149.75 Y
Add 15% CPOH on "Y" 22.46
TOTAL 172.21 Z
Add Cess @ 1% on "Z" 1.72
Cost of 1 no. 173.93
Say 173.95
SUB HEAD : 18- WATER SUPPLY 1716
18.90.6 For 48.60 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8817 Elbow 90° for 48.60 mm outer dia
SS pipe each 1.00 160.00 160.00
TOTAL 160.00 W
Add 1 % Water charges on "W" 1.60
TOTAL 161.60 X
Add GST on "X" (multiplying
factor 0.1405) 22.70
TOTAL 184.30 Y
Add 15% CPOH on "Y" 27.65
TOTAL 211.95 Z
Add Cess @ 1% on "Z" 2.12
Cost of 1 no. 214.07
Say 214.05
18.90A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Elbow 90°
18.90A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3891 Elbow 90° for 15 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 305.00 305.00
TOTAL 305.00 W
Add 1 % Water charges on "W" 3.05
TOTAL 308.05 X
Add GST on "X" (multiplying
factor 0.1405) 43.28
TOTAL 351.33 Y
Add 15% CPOH on "Y" 52.70
TOTAL 404.03 Z
Add Cess @ 1% on "Z" 4.04
Cost of 1 no. 408.07
Say 408.05
SUB HEAD : 18- WATER SUPPLY 1717
18.90A.2 For 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3892 Elbow 90° for 22 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 430.00 430.00
TOTAL 430.00 W
Add 1 % Water charges on "W" 4.30
TOTAL 434.30 X
Add GST on "X" (multiplying
factor 0.1405) 61.02
TOTAL 495.32 Y
Add 15% CPOH on "Y" 74.30
TOTAL 569.62 Z
Add Cess @ 1% on "Z" 5.70
Cost of 1 no. 575.31
Say 575.30
18.90A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3893 Elbow 90° for 28 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 575.00 575.00
TOTAL 575.00 W
Add 1 % Water charges on "W" 5.75
TOTAL 580.75 X
Add GST on "X" (multiplying
factor 0.1405) 81.60
TOTAL 662.35 Y
Add 15% CPOH on "Y" 99.35
TOTAL 761.70 Z
Add Cess @ 1% on "Z" 7.62
Cost of 1 no. 769.31
Say 769.30
18.90A.4 For 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3894 Elbow 90° for 35 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 940.00 940.00
TOTAL 940.00 W
Add 1 % Water charges on "W" 9.40
SUB HEAD : 18- WATER SUPPLY 1718
Code Description Unit Quantity Rate Amount
TOTAL 949.40 X
Add GST on "X" (multiplying
factor 0.1405) 133.39
TOTAL 1082.79 Y
Add 15% CPOH on "Y" 162.42
TOTAL 1245.21 Z
Add Cess @ 1% on "Z" 12.45
Cost of 1 no. 1257.66
Say 1257.65
18.90A.5 For 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3895 Elbow 90° for 42 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1520.00 1520.00
TOTAL 1520.00 W
Add 1 % Water charges on "W" 15.20
TOTAL 1535.20 X
Add GST on "X" (multiplying
factor 0.1405) 215.70
TOTAL 1750.90 Y
Add 15% CPOH on "Y" 262.63
TOTAL 2013.53 Z
Add Cess @ 1% on "Z" 20.14
Cost of 1 no. 2033.67
Say 2033.65
18.90A.6 For 54 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3896 Elbow 90° for 54 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 2010.00 2010.00
TOTAL 2010.00 W
Add 1 % Water charges on "W" 20.10
TOTAL 2030.10 X
Add GST on "X" (multiplying
factor 0.1405) 285.23
TOTAL 2315.33 Y
Add 15% CPOH on "Y" 347.30
TOTAL 2662.63 Z
Add Cess @ 1% on "Z" 26.63
Cost of 1 no. 2689.25
Say 2689.25
SUB HEAD : 18- WATER SUPPLY 1719
18.91 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Reducing Elbow 90°
18.91.1 For22.22 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8818 Reducing Elbow 90° for 22.22 mm X
15.88 mm outer dia SS pipe each 1.00 150.00 150.00
TOTAL 150.00 W
Add 1 % Water charges on "W" 1.50
TOTAL 151.50 X
Add GST on "X" (multiplying
factor 0.1405) 21.29
TOTAL 172.79 Y
Add 15% CPOH on "Y" 25.92
TOTAL 198.70 Z
Add Cess @ 1% on "Z" 1.99
Cost of 1 no. 200.69
Say 200.70
18.91.2 For 28.58 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8819 Reducing Elbow 90° for 28.58 mm X
15.88 mm outer dia SS pipe each 1.00 210.00 210.00
TOTAL 210.00 W
Add 1 % Water charges on "W" 2.10
TOTAL 212.10 X
Add GST on "X" (multiplying
factor 0.1405) 29.80
TOTAL 241.90 Y
Add 15% CPOH on "Y" 36.29
TOTAL 278.19 Z
Add Cess @ 1% on "Z" 2.78
Cost of 1 no. 280.97
Say 280.95
18.91.3 For 28.58 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8820 Reducing Elbow 90° for 28.58 mm X
22.22 mm outer dia SS pipe each 1.00 250.00 250.00
SUB HEAD : 18- WATER SUPPLY 1720
Code Description Unit Quantity Rate Amount
TOTAL 250.00 W
Add 1 % Water charges on "W" 2.50
TOTAL 252.50 X
Add GST on "X" (multiplying
factor 0.1405) 35.48
TOTAL 287.98 Y
Add 15% CPOH on "Y" 43.20
TOTAL 331.17 Z
Add Cess @ 1% on "Z" 3.31
Cost of 1 no. 334.48
Say 334.50
18.91.4 For 34.00 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8821 Reducing Elbow 90° for 34.00 mm X
22.22 mm outer dia SS pipe each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost of 1 no. 394.69
Say 394.70
18.91.5 For 34.00 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8822 Reducing Elbow 90° for 34.00 mm X
28.58 mm outer dia SS pipe each 1.00 350.00 350.00
TOTAL 350.00 W
Add 1 % Water charges on "W" 3.50
TOTAL 353.50 X
Add GST on "X" (multiplying
factor 0.1405) 49.67
TOTAL 403.17 Y
Add 15% CPOH on "Y" 60.48
TOTAL 463.64 Z
Add Cess @ 1% on "Z" 4.64
Cost of 1 no. 468.28
Say 468.30
SUB HEAD : 18- WATER SUPPLY 1721
18.91.6 For 42.70 mm x 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8823 Reducing Elbow 90° for 42.70 mm X
34.00 mm outer dia SS pipe each 1.00 190.00 190.00
TOTAL 190.00 W
Add 1 % Water charges on "W" 1.90
TOTAL 191.90 X
Add GST on "X" (multiplying
factor 0.1405) 26.96
TOTAL 218.86 Y
Add 15% CPOH on "Y" 32.83
TOTAL 251.69 Z
Add Cess @ 1% on "Z" 2.52
Cost of 1 no. 254.21
Say 254.20
18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Equal Tee
18.92.1 For 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8824 Equal Tee for 15.88 mm outer dia
SS pipe each 1.00 175.00 175.00
TOTAL 175.00 W
Add 1 % Water charges on "W" 1.75
TOTAL 176.75 X
Add GST on "X" (multiplying
factor 0.1405) 24.83
TOTAL 201.58 Y
Add 15% CPOH on "Y" 30.24
TOTAL 231.82 Z
Add Cess @ 1% on "Z" 2.32
Cost of 1 no. 234.14
Say 234.15
18.92.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8825 Equal Tee for 22.22 mm outer dia
SS pipe each 1.00 250.00 250.00
SUB HEAD : 18- WATER SUPPLY 1722
Code Description Unit Quantity Rate Amount
TOTAL 250.00 W
Add 1 % Water charges on "W" 2.50
TOTAL 252.50 X
Add GST on "X" (multiplying
factor 0.1405) 35.48
TOTAL 287.98 Y
Add 15% CPOH on "Y" 43.20
TOTAL 331.17 Z
Add Cess @ 1% on "Z" 3.31
Cost of 1 no. 334.48
Say 334.50
18.92.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8826 Equal Tee for 28.58 mm outer dia
SS pipe each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost of 1 no. 394.69
Say 394.70
18.92.4 For 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8827 Equal Tee for 34.00 mm outer dia
SS pipe each 1.00 440.00 440.00
TOTAL 440.00 W
Add 1 % Water charges on "W" 4.40
TOTAL 444.40 X
Add GST on "X" (multiplying
factor 0.1405) 62.44
TOTAL 506.84 Y
Add 15% CPOH on "Y" 76.03
TOTAL 582.86 Z
Add Cess @ 1% on "Z" 5.83
Cost of 1 no. 588.69
Say 588.70
SUB HEAD : 18- WATER SUPPLY 1723
18.92.5 For 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8828 Equal Tee for 42.70 mm outer dia
SS pipe each 1.00 695.00 695.00
TOTAL 695.00 W
Add 1 % Water charges on "W" 6.95
TOTAL 701.95 X
Add GST on "X" (multiplying
factor 0.1405) 98.62
TOTAL 800.57 Y
Add 15% CPOH on "Y" 120.09
TOTAL 920.66 Z
Add Cess @ 1% on "Z" 9.21
Cost of 1 no. 929.87
Say 929.85
18.92.6 For 48.60 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8829 Equal Tee for 48.60 mm outer dia
SS pipe each 1.00 915.00 915.00
TOTAL 915.00 W
Add 1 % Water charges on "W" 9.15
TOTAL 924.15 X
Add GST on "X" (multiplying
factor 0.1405) 129.84
TOTAL 1053.99 Y
Add 15% CPOH on "Y" 158.10
TOTAL 1212.09 Z
Add Cess @ 1% on "Z" 12.12
Cost of 1 no. 1224.21
Say 1224.20
18.92A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Equal Tee
18.92A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3897 Equal Tee for 15 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 500.00 500.00
TOTAL 500.00 W
Add 1 % Water charges on "W" 5.00
SUB HEAD : 18- WATER SUPPLY 1724
Code Description Unit Quantity Rate Amount
TOTAL 505.00 X
Add GST on "X" (multiplying
factor 0.1405) 70.95
TOTAL 575.95 Y
Add 15% CPOH on "Y" 86.39
TOTAL 662.35 Z
Add Cess @ 1% on "Z" 6.62
Cost of 1 no. 668.97
Say 668.95
18.92A.2 For 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3898 Equal Tee for 22 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 585.00 585.00
TOTAL 585.00 W
Add 1 % Water charges on "W" 5.85
TOTAL 590.85 X
Add GST on "X" (multiplying
factor 0.1405) 83.01
TOTAL 673.86 Y
Add 15% CPOH on "Y" 101.08
TOTAL 774.94 Z
Add Cess @ 1% on "Z" 7.75
Cost of 1 no. 782.69
Say 782.70
18.92A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3899 Equal Tee for 28 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 720.00 720.00
TOTAL 720.00 W
Add 1 % Water charges on "W" 7.20
TOTAL 727.20 X
Add GST on "X" (multiplying
factor 0.1405) 102.17
TOTAL 829.37 Y
Add 15% CPOH on "Y" 124.41
TOTAL 953.78 Z
Add Cess @ 1% on "Z" 9.54
Cost of 1 no. 963.32
Say 963.30
SUB HEAD : 18- WATER SUPPLY 1725
18.92A.4 For 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3900 Equal Tee for 35 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.92A.5 For 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3901 Equal Tee for 42 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1250.00 1250.00
TOTAL 1250.00 W
Add 1 % Water charges on "W" 12.50
TOTAL 1262.50 X
Add GST on "X" (multiplying
factor 0.1405) 177.38
TOTAL 1439.88 Y
Add 15% CPOH on "Y" 215.98
TOTAL 1655.86 Z
Add Cess @ 1% on "Z" 16.56
Cost of 1 no. 1672.42
Say 1672.40
18.92A.6 For 54 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3902 Equal Tee for 54 mm outer dia SS pipe
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1500.00 1500.00
TOTAL 1500.00 W
Add 1 % Water charges on "W" 15.00
TOTAL 1515.00 X
SUB HEAD : 18- WATER SUPPLY 1726
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 212.86
TOTAL 1727.86 Y
Add 15% CPOH on "Y" 259.18
TOTAL 1987.04 Z
Add Cess @ 1% on "Z" 19.87
Cost of 1 no. 2006.91
Say 2006.90
18.93 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Reducing Tee
18.93.1 For 22.22 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8830 Reducing Tee for 22.22 mm X
15.88 mm outer dia SS each 1.00 185.00 185.00
TOTAL 185.00 W
Add 1 % Water charges on "W" 1.85
TOTAL 186.85 X
Add GST on "X" (multiplying
factor 0.1405) 26.25
TOTAL 213.10 Y
Add 15% CPOH on "Y" 31.97
TOTAL 245.07 Z
Add Cess @ 1% on "Z" 2.45
Cost of 1 no. 247.52
Say 247.50
18.93.2 For 28.58 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8831 Reducing Tee for 28.58 mm X
15.88 mm outer dia SS pipe each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
SUB HEAD : 18- WATER SUPPLY 1727
18.93.3 For 28.58 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8832 Reducing Tee for 28.58 mm X
22.22 mm outer dia SS pipe each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
18.93.4 For 34.00 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8833 Reducing Tee for 34.00 mm X
15.88 mm outer dia SS pipe each 1.00 440.00 440.00
TOTAL 440.00 W
Add 1 % Water charges on "W" 4.40
TOTAL 444.40 X
Add GST on "X" (multiplying
factor 0.1405) 62.44
TOTAL 506.84 Y
Add 15% CPOH on "Y" 76.03
TOTAL 582.86 Z
Add Cess @ 1% on "Z" 5.83
Cost of 1 no. 588.69
Say 588.70
18.93.5 For 34.00 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8834 Reducing Tee for 34.00 mm X
22.22 mm outer dia SS pipe each 1.00 440.00 440.00
TOTAL 440.00 W
Add 1 % Water charges on "W" 4.40
TOTAL 444.40 X
Add GST on "X" (multiplying
factor 0.1405) 62.44
TOTAL 506.84 Y
Add 15% CPOH on "Y" 76.03
TOTAL 582.86 Z
Add Cess @ 1% on "Z" 5.83
Cost of 1 no. 588.69
Say 588.70
SUB HEAD : 18- WATER SUPPLY 1728
18.93.6 For 34.00 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8835 Reducing Tee for 34.00 mm X
28.58 mm outer dia SS pipe each 1.00 440.00 440.00
TOTAL 440.00 W
Add 1 % Water charges on "W" 4.40
TOTAL 444.40 X
Add GST on "X" (multiplying
factor 0.1405) 62.44
TOTAL 506.84 Y
Add 15% CPOH on "Y" 76.03
TOTAL 582.86 Z
Add Cess @ 1% on "Z" 5.83
Cost of 1 no. 588.69
Say 588.70
18.93.7 For 42.70 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8836 Reducing Tee for 42.70 mm X
15.88 mm outer dia SS pipe each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
18.93.8 For 42.70 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8837 Reducing Tee for 42.70 mm X
22.22 mm outer dia SS pipe each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
SUB HEAD : 18- WATER SUPPLY 1729
18.93.8 For 42.70 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8837 Reducing Tee for 42.70 mm X
22.22 mm outer dia SS pipe each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
18.93.9 For 42.70 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8838 Reducing Tee for 42.70 mm X
28.58 mm outer dia SS pipe each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
18.93.10 For 42.70 mm x 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8839 Reducing Tee for 42.70 mm X
34.00 mm outer dia SS pipe each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
SUB HEAD : 18- WATER SUPPLY 1730
18.93.11 For 48.60 mm x 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8840 Reducing Tee for 48.60 mm X
15.88 mm outer dia SS pipe each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.93.12 For 48.60 mm x 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8841 Reducing Tee for 48.60 mm X
22.22 mm outer dia SS pipe each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.93.13 For 48.60 mm x 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8842 Reducing Tee for 48.60 mm X
28.58 mm outer dia SS pipe each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
SUB HEAD : 18- WATER SUPPLY 1731
18.93.14 For 48.60 mm x 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8843 Reducing Tee for 48.60mm X
34.00 mm outer dia SS pipe each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.93.15 For 48.60 mm x 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8844 Reducing Tee for 48.60mm X
42.70mm outer dia SS pipe each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.93A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Reducing Tee
18.93A.1 For 22 mm x 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3903 Reducing Tee for 22 mm x 15 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 575.00 575.00
TOTAL 575.00 W
SUB HEAD : 18- WATER SUPPLY 1732
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 5.75
TOTAL 580.75 X
Add GST on "X" (multiplying
factor 0.1405) 81.60
TOTAL 662.35 Y
Add 15% CPOH on "Y" 99.35
TOTAL 761.70 Z
Add Cess @ 1% on "Z" 7.62
Cost of 1 no. 769.31
Say 769.30
18.93A.2 For 28 mm x 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3904 Reducing Tee for 28 mm X 15 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 715.00 715.00
TOTAL 715.00 W
Add 1 % Water charges on "W" 7.15
TOTAL 722.15 X
Add GST on "X" (multiplying
factor 0.1405) 101.46
TOTAL 823.61 Y
Add 15% CPOH on "Y" 123.54
TOTAL 947.15 Z
Add Cess @ 1% on "Z" 9.47
Cost of 1 no. 956.63
Say 956.65
18.93A.3 For 28 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3905 Reducing Tee for 28 mm X 22 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
SUB HEAD : 18- WATER SUPPLY 1733
18.93A.4 For 35 mm x 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3906 Reducing Tee for 35 mm X 15 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 900.00 900.00
TOTAL 900.00 W
Add 1 % Water charges on "W" 9.00
TOTAL 909.00 X
Add GST on "X" (multiplying
factor 0.1405) 127.71
TOTAL 1036.71 Y
Add 15% CPOH on "Y" 155.51
TOTAL 1192.22 Z
Add Cess @ 1% on "Z" 11.92
Cost of 1 no. 1204.14
Say 1204.15
18.93A.5 For 35 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3907 Reducing Tee for 35 mm X 22 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.93A.6 For 35 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3908 Reducing Tee for 35 mm X 28 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 915.00 915.00
SUB HEAD : 18- WATER SUPPLY 1734
Code Description Unit Quantity Rate Amount
TOTAL 915.00 W
Add 1 % Water charges on "W" 9.15
TOTAL 924.15 X
Add GST on "X" (multiplying
factor 0.1405) 129.84
TOTAL 1053.99 Y
Add 15% CPOH on "Y" 158.10
TOTAL 1212.09 Z
Add Cess @ 1% on "Z" 12.12
Cost of 1 no. 1224.21
Say 1224.20
18.93A.7 For 42 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3909 Reducing Tee for 42 mm X 22 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1280.00 1280.00
TOTAL 1280.00 W
Add 1 % Water charges on "W" 12.80
TOTAL 1292.80 X
Add GST on "X" (multiplying
factor 0.1405) 181.64
TOTAL 1474.44 Y
Add 15% CPOH on "Y" 221.17
TOTAL 1695.60 Z
Add Cess @ 1% on "Z" 16.96
Cost of 1 no. 1712.56
Say 1712.55
18.93A.8 For 42 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3910 Reducing Tee for 42 mm X 28 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1265.00 1265.00
TOTAL 1265.00 W
Add 1 % Water charges on "W" 12.65
TOTAL 1277.65 X
Add GST on "X" (multiplying
factor 0.1405) 179.51
TOTAL 1457.16 Y
Add 15% CPOH on "Y" 218.57
TOTAL 1675.73 Z
Add Cess @ 1% on "Z" 16.76
Cost of 1 no. 1692.49
Say 1692.50
SUB HEAD : 18- WATER SUPPLY 1735
18.93A.9 For 42 mm x 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3911 Reducing Tee for 42 mm X 35 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1290.00 1290.00
TOTAL 1290.00 W
Add 1 % Water charges on "W" 12.90
TOTAL 1302.90 X
Add GST on "X" (multiplying
factor 0.1405) 183.06
TOTAL 1485.96 Y
Add 15% CPOH on "Y" 222.89
TOTAL 1708.85 Z
Add Cess @ 1% on "Z" 17.09
Cost of 1 no. 1725.94
Say 1725.95
18.93A.10 For 54 mm x 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3912 Reducing Tee for 54 mm X 22 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1500.00 1500.00
TOTAL 1500.00 W
Add 1 % Water charges on "W" 15.00
TOTAL 1515.00 X
Add GST on "X" (multiplying
factor 0.1405) 212.86
TOTAL 1727.86 Y
Add 15% CPOH on "Y" 259.18
TOTAL 1987.04 Z
Add Cess @ 1% on "Z" 19.87
Cost of 1 no. 2006.91
Say 2006.90
18.93A.11 For 54 mm x 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3913 Reducing Tee for 54 mm X 28 mm
outer dia SS pipe of grade 316
conforming to IS 6911:2017 each 1.00 1540.00 1540.00
TOTAL 1540.00 W
Add 1 % Water charges on "W" 15.40
SUB HEAD : 18- WATER SUPPLY 1736
Code Description Unit Quantity Rate Amount
TOTAL 1555.40 X
Add GST on "X" (multiplying
factor 0.1405) 218.53
TOTAL 1773.93 Y
Add 15% CPOH on "Y" 266.09
TOTAL 2040.02 Z
Add Cess @ 1% on "Z" 20.40
Cost of 1 no. 2060.42
Say 2060.40
18.93A.12 For 54 mm x 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3914 Reducing Tee for 54 mm X 35 mm
outer dia SS pipe of grade 316L as per
IS 6911:2017 and conforming to
EN-10312 each 1.00 1550.00 1550.00
TOTAL 1550.00 W
Add 1 % Water charges on "W" 15.50
TOTAL 1565.50 X
Add GST on "X" (multiplying
factor 0.1405) 219.95
TOTAL 1785.45 Y
Add 15% CPOH on "Y" 267.82
TOTAL 2053.27 Z
Add Cess @ 1% on "Z" 20.53
Cost of 1 no. 2073.80
Say 2073.80
18.93A.13 For 54 mm x 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3915 Reducing Tee for 54mm X 42mm outer
dia SS pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1570.00 1570.00
TOTAL 1570.00 W
Add 1 % Water charges on "W" 15.70
TOTAL 1585.70 X
Add GST on "X" (multiplying
factor 0.1405) 222.79
TOTAL 1808.49 Y
Add 15% CPOH on "Y" 271.27
TOTAL 2079.76 Z
Add Cess @ 1% on "Z" 20.80
Cost of 1 no. 2100.56
Say 2100.55
SUB HEAD : 18- WATER SUPPLY 1737
18.94 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Male Thread Tee
18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8845 Stainless steel Male thread Tee for
15.88 mm outer dia X 15 mm nominal
dia threaded each 1.00 185.00 185.00
TOTAL 185.00 W
Add 1 % Water charges on "W" 1.85
TOTAL 186.85 X
Add GST on "X" (multiplying
factor 0.1405) 26.25
TOTAL 213.10 Y
Add 15% CPOH on "Y" 31.97
TOTAL 245.07 Z
Add Cess @ 1% on "Z" 2.45
Cost of 1 no. 247.52
Say 247.50
18.94.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8846 Stainless steel Male thread Tee for
22.22 mm outer dia X 15 mm nominal
dia threaded each 1.00 215.00 215.00
TOTAL 215.00 W
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost of 1 no. 287.66
Say 287.65
18.94.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8847 Stainless steel Male thread Tee for
22.22 mm outer dia X 20 mm nominal
dia threaded each 1.00 215.00 215.00
TOTAL 215.00 W
SUB HEAD : 18- WATER SUPPLY 1738
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost of 1 no. 287.66
Say 287.65
18.94.4 For 28.58 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8848 Stainless steel Male thread Tee for
28.58 mm outer dia X 15 mm nominal
dia threaded each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost of 1 no. 394.69
Say 394.70
18.94.5 For 28.58 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8849 Stainless steel Male thread Tee for
28.58 mm outer dia X 20 mm nominal
dia threaded each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost of 1 no. 394.69
Say 394.70
SUB HEAD : 18- WATER SUPPLY 1739
18.94.6 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8850 Stainless steel Male thread Tee for
28.58 mm outer dia X 20 mm nominal
dia threaded each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost of 1 no. 394.69
Say 394.70
18.94.7 For 34.00 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8851 Stainless steel Male thread Tee for
34.00 mm outer dia X 15 mm nominal
dia threaded each 1.00 465.00 465.00
TOTAL 465.00 W
Add 1 % Water charges on "W" 4.65
TOTAL 469.65 X
Add GST on "X" (multiplying
factor 0.1405) 65.99
TOTAL 535.64 Y
Add 15% CPOH on "Y" 80.35
TOTAL 615.98 Z
Add Cess @ 1% on "Z" 6.16
Cost of 1 no. 622.14
Say 622.15
18.94.8 For 34.00 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8852 Stainless steel Male thread Tee for
34.00 mm outer dia X 20 mm nominal
dia threaded each 1.00 465.00 465.00
TOTAL 465.00 W
Add 1 % Water charges on "W" 4.65
TOTAL 469.65 X
Add GST on "X" (multiplying
factor 0.1405) 65.99
TOTAL 535.64 Y
Add 15% CPOH on "Y" 80.35
TOTAL 615.98 Z
Add Cess @ 1% on "Z" 6.16
Cost of 1 no. 622.14
Say 622.15
SUB HEAD : 18- WATER SUPPLY 1740
18.94.9 For 34.00 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8853 Stainless steel Male thread Tee for
34.00 mm outer dia X 25 mm nominal
dia threaded each 1.00 465.00 465.00
TOTAL 465.00 W
Add 1 % Water charges on "W" 4.65
TOTAL 469.65 X
Add GST on "X" (multiplying
factor 0.1405) 65.99
TOTAL 535.64 Y
Add 15% CPOH on "Y" 80.35
TOTAL 615.98 Z
Add Cess @ 1% on "Z" 6.16
Cost of 1 no. 622.14
Say 622.15
18.94.10 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8854 Stainless steel Male thread Tee for
34.00 mm outer dia X 32 mm nominal
dia threaded each 1.00 465.00 465.00
TOTAL 465.00 W
Add 1 % Water charges on "W" 4.65
TOTAL 469.65 X
Add GST on "X" (multiplying
factor 0.1405) 65.99
TOTAL 535.64 Y
Add 15% CPOH on "Y" 80.35
TOTAL 615.98 Z
Add Cess @ 1% on "Z" 6.16
Cost of 1 no. 622.14
Say 622.15
18.94.11 For 42.70 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8855 Stainless steel Male thread Tee for
42.70 mm outer dia X 15 mm nominal
dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
SUB HEAD : 18- WATER SUPPLY 1741
18.94.12 For 42.70 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8856 Stainless steel Male thread Tee for
42.70 mm outer dia X 20 mm nominal
dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
18.94.13 For 42.70 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8857 Stainless steel Male thread Tee for
42.70 mm outer dia X 25 mm nominal
dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
18.94.14 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8858 Stainless steel Male thread Tee for
42.70 mm outer dia X 32 mm nominal
dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
SUB HEAD : 18- WATER SUPPLY 1742
18.94.15 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8859 Stainless steel Male thread Tee for
42.70 mm outer dia X 40 mm nominal
dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
18.94.16 For 48.60 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8860 Stainless steel Male thread Tee for
48.60 mm outer dia X 15 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.94.17 For 48.60 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8861 Stainless steel Male thread Tee for
48.60 mm outer dia X 20 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
SUB HEAD : 18- WATER SUPPLY 1743
18.94.18 For 48.60 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8862 Stainless steel Male thread Tee for
48.60 mm outer dia X 25 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.94.19 For 48.60 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8863 Stainless steel Male thread Tee for
48.60 mm outer dia X 32 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.94.20 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8864 Stainless steel Male thread Tee for
48.60 mm outer dia X 40 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
SUB HEAD : 18- WATER SUPPLY 1744
18.94.21 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8865 Stainless steel Male thread Tee for
48.60 mm outer dia X 50 mm nominal
dia threaded each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.95 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Female Thread Tee
18.95.1 For 15.88 mm outer dia x15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8866 Stainless steel Female thread Tee for
15.88 mm outer dia X 15 mm nominal
dia hreaded each 1.00 185.00
185.00
TOTAL 185.00 W
Add 1 % Water charges on "W" 1.85
TOTAL 186.85 X
Add GST on "X" (multiplying
factor 0.1405) 26.25
TOTAL 213.10 Y
Add 15% CPOH on "Y" 31.97
TOTAL 245.07 Z
Add Cess @ 1% on "Z" 2.45
Cost of 1 no. 247.52
Say 247.50
18.95.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8867 Stainless steel Female thread Tee for
22.22 mm outer dia X 15 mm nominal
dia threaded each 1.00 205.00 205.00
TOTAL 205.00 W
SUB HEAD : 18- WATER SUPPLY 1745
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 2.05
TOTAL 207.05 X
Add GST on "X" (multiplying
factor 0.1405) 29.09
TOTAL 236.14 Y
Add 15% CPOH on "Y" 35.42
TOTAL 271.56 Z
Add Cess @ 1% on "Z" 2.72
Cost of 1 no. 274.28
Say 274.30
18.95.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8868 Stainless steel Female thread Tee for
22.22 mm outer dia X 20 mm nominal
dia threaded each 1.00 205.00 205.00
TOTAL 205.00 W
Add 1 % Water charges on "W" 2.05
TOTAL 207.05 X
Add GST on "X" (multiplying
factor 0.1405) 29.09
TOTAL 236.14 Y
Add 15% CPOH on "Y" 35.42
TOTAL 271.56 Z
Add Cess @ 1% on "Z" 2.72
Cost of 1 no. 274.28
Say 274.30
18.95.4 For 28.58 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8869 Stainless steel Female thread Tee for
28.58 mm outer dia X 15 mm nominal
dia threaded each 1.00 275.00 275.00
TOTAL 275.00 W
Add 1 % Water charges on "W" 2.75
TOTAL 277.75 X
Add GST on "X" (multiplying
factor 0.1405) 39.02
TOTAL 316.77 Y
Add 15% CPOH on "Y" 47.52
TOTAL 364.29 Z
Add Cess @ 1% on "Z" 3.64
Cost of 1 no. 367.93
Say 367.95
SUB HEAD : 18- WATER SUPPLY 1746
18.95.5 For 28.58 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8870 Stainless steel Female thread Tee for
28.58 mm outer dia X 20 mm nominal
dia threaded each 1.00 275.00 275.00
TOTAL 275.00 W
Add 1 % Water charges on "W" 2.75
TOTAL 277.75 X
Add GST on "X" (multiplying
factor 0.1405) 39.02
TOTAL 316.77 Y
Add 15% CPOH on "Y" 47.52
TOTAL 364.29 Z
Add Cess @ 1% on "Z" 3.64
Cost of 1 no. 367.93
Say 367.95
18.95.6 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8871 Stainless steel Female thread Tee for
28.58 mm outer dia X 25 mm nominal
dia threaded each 1.00 275.00 275.00
TOTAL 275.00 W
Add 1 % Water charges on "W" 2.75
TOTAL 277.75 X
Add GST on "X" (multiplying
factor 0.1405) 39.02
TOTAL 316.77 Y
Add 15% CPOH on "Y" 47.52
TOTAL 364.29 Z
Add Cess @ 1% on "Z" 3.64
Cost of 1 no. 367.93
Say 367.95
18.95.7 For 34.00 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8872 Stainless steel Female thread Tee for
34.00 mm outer dia X 15 mm nominal
dia threaded each 1.00 445.00 445.00
TOTAL 445.00 W
Add 1 % Water charges on "W" 4.45
TOTAL 449.45 X
SUB HEAD : 18- WATER SUPPLY 1747
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 63.15
TOTAL 512.60 Y
Add 15% CPOH on "Y" 76.89
TOTAL 589.49 Z
Add Cess @ 1% on "Z" 5.89
Cost of 1 no. 595.38
Say 595.40
18.95.8 For 34.00 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8873 Stainless steel Female thread Tee for
34.00 mm outer dia X 20 mm nominal
dia threaded each 1.00 445.00 445.00
TOTAL 445.00 W
Add 1 % Water charges on "W" 4.45
TOTAL 449.45 X
Add GST on "X" (multiplying
factor 0.1405) 63.15
TOTAL 512.60 Y
Add 15% CPOH on "Y" 76.89
TOTAL 589.49 Z
Add Cess @ 1% on "Z" 5.89
Cost of 1 no. 595.38
Say 595.40
18.95.9 For 34.00 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8874 Stainless steel Female thread Tee for
34.00 mm outer dia X 25 mm nominal
dia threaded each 1.00 445.00 445.00
TOTAL 445.00 W
Add 1 % Water charges on "W" 4.45
TOTAL 449.45 X
Add GST on "X" (multiplying
factor 0.1405) 63.15
TOTAL 512.60 Y
Add 15% CPOH on "Y" 76.89
TOTAL 589.49 Z
Add Cess @ 1% on "Z" 5.89
Cost of 1 no. 595.38
Say 595.40
SUB HEAD : 18- WATER SUPPLY 1748
18.95.10 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8875 Stainless steel Female thread Tee for
34.00 mm outer dia X 32 mm nominal
dia threaded each 1.00 445.00 445.00
TOTAL 445.00 W
Add 1 % Water charges on "W" 4.45
TOTAL 449.45 X
Add GST on "X" (multiplying
factor 0.1405) 63.15
TOTAL 512.60 Y
Add 15% CPOH on "Y" 76.89
TOTAL 589.49 Z
Add Cess @ 1% on "Z" 5.89
Cost of 1 no. 595.38
Say 595.40
18.95.11 For 42.70 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8876 Stainless steel Female thread Tee for
42.70 mm outer dia X 15 mm nominal
dia threaded each 1.00 700.00 700.00
TOTAL 700.00 W
Add 1 % Water charges on "W" 7.00
TOTAL 707.00 X
Add GST on "X" (multiplying
factor 0.1405) 99.33
TOTAL 806.33 Y
Add 15% CPOH on "Y" 120.95
TOTAL 927.28 Z
Add Cess @ 1% on "Z" 9.27
Cost of 1 no. 936.56
Say 936.55
18.95.12 For 42.70 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8877 Stainless steel Female thread Tee for
42.70 mm outer dia X 20 mm nominal
dia threaded each 1.00 700.00 700.00
TOTAL 700.00 W
SUB HEAD : 18- WATER SUPPLY 1749
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 7.00
TOTAL 707.00 X
Add GST on "X" (multiplying
factor 0.1405) 99.33
TOTAL 806.33 Y
Add 15% CPOH on "Y" 120.95
TOTAL 927.28 Z
Add Cess @ 1% on "Z" 9.27
Cost of 1 no. 936.56
Say 936.55
18.95.13 For 42.70 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8878 Stainless steel Female thread Tee for
42.70 mm outer dia X 25 mm nominal
dia threaded each 1.00 700.00 700.00
TOTAL 700.00 W
Add 1 % Water charges on "W" 7.00
TOTAL 707.00 X
Add GST on "X" (multiplying
factor 0.1405) 99.33
TOTAL 806.33 Y
Add 15% CPOH on "Y" 120.95
TOTAL 927.28 Z
Add Cess @ 1% on "Z" 9.27
Cost of 1 no. 936.56
Say 936.55
18.95.14 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8879 Stainless steel Female thread Tee for
42.70 mm outer dia X 32 mm nominal
dia threaded each 1.00 700.00 700.00
TOTAL 700.00 W
Add 1 % Water charges on "W" 7.00
TOTAL 707.00 X
Add GST on "X" (multiplying
factor 0.1405) 99.33
TOTAL 806.33 Y
Add 15% CPOH on "Y" 120.95
TOTAL 927.28 Z
Add Cess @ 1% on "Z" 9.27
Cost of 1 no. 936.56
Say 936.55
SUB HEAD : 18- WATER SUPPLY 1750
18.95.15 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8880 Stainless steel Female thread Tee for
42.70 mm outer dia X 40 mm nominal
dia threaded each 1.00 700.00 700.00
TOTAL 700.00 W
Add 1 % Water charges on "W" 7.00
TOTAL 707.00 X
Add GST on "X" (multiplying
factor 0.1405) 99.33
TOTAL 806.33 Y
Add 15% CPOH on "Y" 120.95
TOTAL 927.28 Z
Add Cess @ 1% on "Z" 9.27
Cost of 1 no. 936.56
Say 936.55
18.95.16 For 48.60 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8881 Stainless steel Female thread Tee for
48.60 mm outer dia X 15 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.95.17 For 48.60 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8882 Stainless steel Female thread Tee for
48.60 mm outer dia X 20 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
SUB HEAD : 18- WATER SUPPLY 1751
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.95.18 For 48.60 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8883 Stainless steel Female thread Tee for
48.60 mm outer dia X 25 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.95.19 For 48.60 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8884 Stainless steel Female thread Tee for
48.60 mm outer dia X 32 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
SUB HEAD : 18- WATER SUPPLY 1752
18.95.20 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8885 Stainless steel Female thread Tee for
48.60 mm outer dia X 40 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.95.21 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8886 Stainless steel Female thread Tee for
48.60 mm outer dia X 50 mm nominal
dia threaded each 1.00 905.00 905.00
TOTAL 905.00 W
Add 1 % Water charges on "W" 9.05
TOTAL 914.05 X
Add GST on "X" (multiplying
factor 0.1405) 128.42
TOTAL 1042.47 Y
Add 15% CPOH on "Y" 156.37
TOTAL 1198.85 Z
Add Cess @ 1% on "Z" 11.99
Cost of 1 no. 1210.83
Say 1210.85
18.95A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Female Thread Tee
18.95A.1 For 15 mm outer dia x 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3916 Stainless steel Female thread Tee for
15 mm outer dia X 1/2" nominal dia
threaded of grade 316L as per
SUB HEAD : 18- WATER SUPPLY 1753
Code Description Unit Quantity Rate Amount
IS 6911:2017 and conforming to
EN-10312 each 1.00 560.00 560.00
TOTAL 560.00 W
Add 1 % Water charges on "W" 5.60
TOTAL 565.60 X
Add GST on "X" (multiplying
factor 0.1405) 79.47
TOTAL 645.07 Y
Add 15% CPOH on "Y" 96.76
TOTAL 741.83 Z
Add Cess @ 1% on "Z" 7.42
Cost of 1 no. 749.25
Say 749.25
18.95A.2 For 22mm outer dia x 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3917 Stainless steel Female thread Tee for
22 mm outer dia X 1/2" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 615.00 615.00
TOTAL 615.00 W
Add 1 % Water charges on "W" 6.15
TOTAL 621.15 X
Add GST on "X" (multiplying
factor 0.1405) 87.27
TOTAL 708.42 Y
Add 15% CPOH on "Y" 106.26
TOTAL 814.68 Z
Add Cess @ 1% on "Z" 8.15
Cost of 1 no. 822.83
Say 822.85
18.95A.3 For 22mm outer dia x 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3918 Stainless steel Female thread Tee for
22 mm outer dia X 3/4" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 690.00 690.00
TOTAL 690.00 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.90 X
Add GST on "X" (multiplying
factor 0.1405) 97.91
SUB HEAD : 18- WATER SUPPLY 1754
Code Description Unit Quantity Rate Amount
TOTAL 794.81 Y
Add 15% CPOH on "Y" 119.22
TOTAL 914.04 Z
Add Cess @ 1% on "Z" 9.14
Cost of 1 no. 923.18
Say 923.20
18.95A.4 For 28 mm outer dia x 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3919 Stainless steel Female thread Tee for
28 mm outer dia X 1/2" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 730.00 730.00
TOTAL 730.00 W
Add 1 % Water charges on "W" 7.30
TOTAL 737.30 X
Add GST on "X" (multiplying
factor 0.1405) 103.59
TOTAL 840.89 Y
Add 15% CPOH on "Y" 126.13
TOTAL 967.02 Z
Add Cess @ 1% on "Z" 9.67
Cost of 1 no. 976.69
Say 976.70
18.95A.5 For 28 mm outer dia x 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3920 Stainless steel Female thread Tee for
28 mm outer dia X 3/4" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 755.00 755.00
TOTAL 755.00 W
Add 1 % Water charges on "W" 7.55
TOTAL 762.55 X
Add GST on "X" (multiplying
factor 0.1405) 107.14
TOTAL 869.69 Y
Add 15% CPOH on "Y" 130.45
TOTAL 1000.14 Z
Add Cess @ 1% on "Z" 10.00
Cost of 1 no. 1010.14
Say 1010.15
SUB HEAD : 18- WATER SUPPLY 1755
18.95A.6 For 28 mm outer dia x 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3921 Stainless steel Female thread Tee for
28 mm outer dia X 1" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 840.00 840.00
TOTAL 840.00 W
Add 1 % Water charges on "W" 8.40
TOTAL 848.40 X
Add GST on "X" (multiplying
factor 0.1405) 119.20
TOTAL 967.60 Y
Add 15% CPOH on "Y" 145.14
TOTAL 1112.74 Z
Add Cess @ 1% on "Z" 11.13
Cost of 1 no. 1123.87
Say 1123.85
18.95A.7 For 35 mm outer dia x 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3922 Stainless steel Female thread Tee for
35 mm outer dia X 1/2" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 845.00 845.00
TOTAL 845.00 W
Add 1 % Water charges on "W" 8.45
TOTAL 853.45 X
Add GST on "X" (multiplying
factor 0.1405) 119.91
TOTAL 973.36 Y
Add 15% CPOH on "Y" 146.00
TOTAL 1119.36 Z
Add Cess @ 1% on "Z" 11.19
Cost of 1 no. 1130.56
Say 1130.55
18.95A.8 For 35 mm outer dia x 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3923 Stainless steel Female thread Tee for
35 mm outer dia X 1-1/4" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1159.00 1159.00
TOTAL 1159.00 W
SUB HEAD : 18- WATER SUPPLY 1756
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 11.59
TOTAL 1170.59 X
Add GST on "X" (multiplying
factor 0.1405) 164.47
TOTAL 1335.06 Y
Add 15% CPOH on "Y" 200.26
TOTAL 1535.32 Z
Add Cess @ 1% on "Z" 15.35
Cost of 1 no. 1550.67
Say 1550.65
18.95A.9 For 42 mm outer dia x 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3924 Stainless steel Female thread Tee for
42 mm outer dia X 1-1/4" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1346.00 1346.00
TOTAL 1346.00 W
Add 1 % Water charges on "W" 13.46
TOTAL 1359.46 X
Add GST on "X" (multiplying
factor 0.1405) 191.00
TOTAL 1550.46 Y
Add 15% CPOH on "Y" 232.57
TOTAL 1783.03 Z
Add Cess @ 1% on "Z" 17.83
Cost of 1 no. 1800.86
Say 1800.85
18.95A.10 For 54 mm outer dia x 1-1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3925 Stainless steel Female thread Tee for
54 mm outer dia X 1-1/2" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1920.00 1920.00
TOTAL 1920.00 W
Add 1 % Water charges on "W" 19.20
TOTAL 1939.20 X
Add GST on "X" (multiplying
factor 0.1405) 272.46
TOTAL 2211.66 Y
Add 15% CPOH on "Y" 331.75
TOTAL 2543.41 Z
Add Cess @ 1% on "Z" 25.43
Cost of 1 no. 2568.84
Say 2568.85
SUB HEAD : 18- WATER SUPPLY 1757
18.95A.11 For 54 mm outer dia x 2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3926 Stainless steel Female thread Tee for
54 mm outer dia X 2" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 2307.00 2307.00
TOTAL 2307.00 W
Add 1 % Water charges on "W" 23.07
TOTAL 2330.07 X
Add GST on "X" (multiplying
factor 0.1405) 327.37
TOTAL 2657.44 Y
Add 15% CPOH on "Y" 398.62
TOTAL 3056.06 Z
Add Cess @ 1% on "Z" 30.56
Cost of 1 no. 3086.62
Say 3086.60
18.96 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Female Thread Connector/ Adapter
18.96.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8887 Stainless steel Female threaded
Connector/Adapter for 15.88 mm outer
dia X 15 mm nominal dia threaded each 1.00 195.00 195.00
TOTAL 195.00 W
Add 1 % Water charges on "W" 1.95
TOTAL 196.95 X
Add GST on "X" (multiplying
factor 0.1405) 27.67
TOTAL 224.62 Y
Add 15% CPOH on "Y" 33.69
TOTAL 258.31 Z
Add Cess @ 1% on "Z" 2.58
Cost of 1 no. 260.90
Say 260.90
18.96.2 For 22.22 mm outer dia x 15 mmnominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
SUB HEAD : 18- WATER SUPPLY 1758
Code Description Unit Quantity Rate Amount
8888 Stainless steel Female threaded
Connector/Adapter for 22.22 mm outer
dia X 15 mm nominal dia threaded each 1.00 230.00 230.00
TOTAL 230.00 W
Add 1 % Water charges on "W" 2.30
TOTAL 232.30 X
Add GST on "X" (multiplying
factor 0.1405) 32.64
TOTAL 264.94 Y
Add 15% CPOH on "Y" 39.74
TOTAL 304.68 Z
Add Cess @ 1% on "Z" 3.05
Cost of 1 no. 307.73
Say 307.75
18.96.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8889 Stainless steel Female threaded
Connector/Adapter for 22.22 mm outer
dia X 20 mm nominal dia threaded each 1.00 240.00 240.00
TOTAL 240.00 W
Add 1 % Water charges on "W" 2.40
TOTAL 242.40 X
Add GST on "X" (multiplying
factor 0.1405) 34.06
TOTAL 276.46 Y
Add 15% CPOH on "Y" 41.47
TOTAL 317.93 Z
Add Cess @ 1% on "Z" 3.18
Cost of 1 no. 321.11
Say 321.10
18.96.4 For 28.58 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8890 Stainless steel Female threaded
Connector/Adapter for 28.58 mm outer
dia X 15 mm nominal dia threaded each 1.00 277.00 277.00
TOTAL 277.00 W
Add 1 % Water charges on "W" 2.77
TOTAL 279.77 X
Add GST on "X" (multiplying
factor 0.1405) 39.31
TOTAL 319.08 Y
Add 15% CPOH on "Y" 47.86
TOTAL 366.94 Z
Add Cess @ 1% on "Z" 3.67
Cost of 1 no. 370.61
Say 370.60
SUB HEAD : 18- WATER SUPPLY 1759
18.96.5 For 28.58 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8891 Stainless steel Female threaded
Connector/Adapter for 28.58 mm outer
dia X 20 mm nominal dia threaded each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
18.96.6 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8892 Stainless steel Female threaded
Connector/Adapter for 28.58 mm outer
dia X 25 mm nominal dia threaded each 1.00 355.00 355.00
TOTAL 355.00 W
Add 1 % Water charges on "W" 3.55
TOTAL 358.55 X
Add GST on "X" (multiplying
factor 0.1405) 50.38
TOTAL 408.93 Y
Add 15% CPOH on "Y" 61.34
TOTAL 470.27 Z
Add Cess @ 1% on "Z" 4.70
Cost of 1 no. 474.97
Say 474.95
18.96.7 For 34.00 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8893 Stainless steel Female threaded
Connector/Adapter for 34.00 mm outer
dia X 25 mm nominal dia threaded each 1.00 410.00 410.00
TOTAL 410.00 W
Add 1 % Water charges on "W" 4.10
TOTAL 414.10 X
SUB HEAD : 18- WATER SUPPLY 1760
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 58.18
TOTAL 472.28 Y
Add 15% CPOH on "Y" 70.84
TOTAL 543.12 Z
Add Cess @ 1% on "Z" 5.43
Cost of 1 no. 548.55
Say 548.55
18.96.8 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8894 Stainless steel Female threaded
Connector/Adapter for 34.00 mm outer
dia X 32 mm nominal dia threaded each 1.00 540.00 540.00
TOTAL 540.00 W
Add 1 % Water charges on "W" 5.40
TOTAL 545.40 X
Add GST on "X" (multiplying
factor 0.1405) 76.63
TOTAL 622.03 Y
Add 15% CPOH on "Y" 93.30
TOTAL 715.33 Z
Add Cess @ 1% on "Z" 7.15
Cost of 1 no. 722.49
Say 722.50
18.96.9 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8895 Stainless steel Female threaded
Connector/Adapter for 42.70 mm outer
dia X 32 mm nominal dia threaded each 1.00 595.00 595.00
TOTAL 595.00 W
Add 1 % Water charges on "W" 5.95
TOTAL 600.95 X
Add GST on "X" (multiplying
factor 0.1405) 84.43
TOTAL 685.38 Y
Add 15% CPOH on "Y" 102.81
TOTAL 788.19 Z
Add Cess @ 1% on "Z" 7.88
Cost of 1 no. 796.07
Say 796.05
SUB HEAD : 18- WATER SUPPLY 1761
18.96.10 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8896 Stainless steel Female threaded
Connector/Adapter for 42.70 mm outer
dia X 40 mm nominal dia threaded each 1.00 695.00 695.00
TOTAL 695.00 W
Add 1 % Water charges on "W" 6.95
TOTAL 701.95 X
Add GST on "X" (multiplying
factor 0.1405) 98.62
TOTAL 800.57 Y
Add 15% CPOH on "Y" 120.09
TOTAL 920.66 Z
Add Cess @ 1% on "Z" 9.21
Cost of 1 no. 929.87
Say 929.85
18.96.11 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8897 Stainless steel Female threaded
Connector/Adapter for 48.60 mm outer
dia X 40 mm nominal dia threaded each 1.00 845.00 845.00
TOTAL 845.00 W
Add 1 % Water charges on "W" 8.45
TOTAL 853.45 X
Add GST on "X" (multiplying
factor 0.1405) 119.91
TOTAL 973.36 Y
Add 15% CPOH on "Y" 146.00
TOTAL 1119.36 Z
Add Cess @ 1% on "Z" 11.19
Cost of 1 no. 1130.56
Say 1130.55
18.96.12 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8898 Stainless steel Female threaded
Connector/Adapter for 48.60 mm outer
dia X 50 mm nominal dia threaded each 1.00 975.00 975.00
TOTAL 975.00 W
Add 1 % Water charges on "W" 9.75
TOTAL 984.75 X
SUB HEAD : 18- WATER SUPPLY 1762
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 138.36
TOTAL 1123.11 Y
Add 15% CPOH on "Y" 168.47
TOTAL 1291.57 Z
Add Cess @ 1% on "Z" 12.92
Cost of 1 no. 1304.49
Say 1304.50
18.96A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standards with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Female Thread Connector/ Adapter
18.96A.1 For 15 mm outer dia x 1/2" mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3927 Stainless steel Female threaded
Connector/Adapter for 15 mm outer dia
X 1/2" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 440.00 440.00
TOTAL 440.00 W
Add 1 % Water charges on "W" 4.40
TOTAL 444.40 X
Add GST on "X" (multiplying
factor 0.1405) 62.44
TOTAL 506.84 Y
Add 15% CPOH on "Y" 76.03
TOTAL 582.86 Z
Add Cess @ 1% on "Z" 5.83
Cost of 1 no. 588.69
Say 588.70
18.96A.2 For 22 mm outer dia x 1/2" mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3928 Stainless steel Female threaded
Connector/Adapter for 22 mm outer dia
X 1/2" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 495.00 495.00
TOTAL 495.00 W
Add 1 % Water charges on "W" 4.95
TOTAL 499.95 X
Add GST on "X" (multiplying
factor 0.1405) 70.24
SUB HEAD : 18- WATER SUPPLY 1763
Code Description Unit Quantity Rate Amount
TOTAL 570.19 Y
Add 15% CPOH on "Y" 85.53
TOTAL 655.72 Z
Add Cess @ 1% on "Z" 6.56
Cost of 1 no. 662.28
Say 662.30
18.96A.3 For 22 mm outer dia x 3/4" mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3929 Stainless steel Female threaded
Connector/Adapter for 22 mm outer dia
X 3/4" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 580.00 580.00
TOTAL 580.00 W
Add 1 % Water charges on "W" 5.80
TOTAL 585.80 X
Add GST on "X" (multiplying
factor 0.1405) 82.30
TOTAL 668.10 Y
Add 15% CPOH on "Y" 100.22
TOTAL 768.32 Z
Add Cess @ 1% on "Z" 7.68
Cost of 1 no. 776.00
Say 776.00
18.96A.4 For 28 mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3930 Stainless steel Female threaded
Connector/Adapter for 28 mm outer dia
X 1" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 955.00 955.00
TOTAL 955.00 W
Add 1 % Water charges on "W" 9.55
TOTAL 964.55 X
Add GST on "X" (multiplying
factor 0.1405) 135.52
TOTAL 1100.07 Y
Add 15% CPOH on "Y" 165.01
TOTAL 1265.08 Z
Add Cess @ 1% on "Z" 12.65
Cost of 1 no. 1277.73
Say 1277.75
SUB HEAD : 18- WATER SUPPLY 1764
18.96A.5 For 35 mm outer dia X 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3931 Stainless steel Female threaded
Connector/Adapter for 35 mm outer dia
X 1-1/4" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1020.00 1020.00
TOTAL 1020.00 W
Add 1 % Water charges on "W" 10.20
TOTAL 1030.20 X
Add GST on "X" (multiplying
factor 0.1405) 144.74
TOTAL 1174.94 Y
Add 15% CPOH on "Y" 176.24
TOTAL 1351.18 Z
Add Cess @ 1% on "Z" 13.51
Cost of 1 no. 1364.70
Say 1364.70
18.96A.6 For 42 mm outer dia X 1-1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3932 Stainless steel Female threaded
Connector/Adapter for 42 mm outer dia
X 1-1/2" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1565.00 1565.00
TOTAL 1565.00 W
Add 1 % Water charges on "W" 15.65
TOTAL 1580.65 X
Add GST on "X" (multiplying
factor 0.1405) 222.08
TOTAL 1802.73 Y
Add 15% CPOH on "Y" 270.41
TOTAL 2073.14 Z
Add Cess @ 1% on "Z" 20.73
Cost of 1 no. 2093.87
Say 2093.85
18.96A.7 For 54 mm outer dia X 2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3933 Stainless steel Female threaded
Connector/Adapter for 54 mm outer dia
X 2" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 2400.00 2400.00
SUB HEAD : 18- WATER SUPPLY 1765
Code Description Unit Quantity Rate Amount
TOTAL 2400.00 W
Add 1 % Water charges on "W" 24.00
TOTAL 2424.00 X
Add GST on "X" (multiplying
factor 0.1405) 340.57
TOTAL 2764.57 Y
Add 15% CPOH on "Y" 414.69
TOTAL 3179.26 Z
Add Cess @ 1% on "Z" 31.79
Cost of 1 no. 3211.05
Say 3211.05
18.97 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Male Thread Connector/ Adapter
18.97.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8899 Stainless steel Male threaded
Connector/ Adapter for 15.88 mm outer
dia X 15 mm nominal dia threaded each 1.00 195.00 195.00
TOTAL 195.00 W
Add 1 % Water charges on "W" 1.95
TOTAL 196.95 X
Add GST on "X" (multiplying
factor 0.1405) 27.67
TOTAL 224.62 Y
Add 15% CPOH on "Y" 33.69
TOTAL 258.31 Z
Add Cess @ 1% on "Z" 2.58
Cost of 1 no. 260.90
Say 260.90
18.97.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8900 Stainless steel Male threaded
Connector/Adapter for 22.22 mm outer
dia X 15 mm nominal dia threaded each 1.00 230.00 230.00
TOTAL 230.00 W
SUB HEAD : 18- WATER SUPPLY 1766
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 2.30
TOTAL 232.30 X
Add GST on "X" (multiplying
factor 0.1405) 32.64
TOTAL 264.94 Y
Add 15% CPOH on "Y" 39.74
TOTAL 304.68 Z
Add Cess @ 1% on "Z" 3.05
Cost of 1 no. 307.73
Say 307.75
18.97.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8901 Stainless steel Male threaded
Connector/Adapter for 22.22 mm outer
dia X 20mm nominal dia threaded each 1.00 255.00 255.00
TOTAL 255.00 W
Add 1 % Water charges on "W" 2.55
TOTAL 257.55 X
Add GST on "X" (multiplying
factor 0.1405) 36.19
TOTAL 293.74 Y
Add 15% CPOH on "Y" 44.06
TOTAL 337.80 Z
Add Cess @ 1% on "Z" 3.38
Cost of 1 no. 341.17
Say 341.15
18.97.4 For 28.58 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8902 Stainless steel Male threaded
Connector/Adapter for 28.58 mm outer
dia X 20 mm nominal dia threaded each 1.00 325.00 325.00
TOTAL 325.00 W
Add 1 % Water charges on "W" 3.25
TOTAL 328.25 X
Add GST on "X" (multiplying
factor 0.1405) 46.12
TOTAL 374.37 Y
Add 15% CPOH on "Y" 56.16
TOTAL 430.52 Z
Add Cess @ 1% on "Z" 4.31
Cost of 1 no. 434.83
Say 434.85
SUB HEAD : 18- WATER SUPPLY 1767
18.97.5 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8903 Stainless steel Male threaded
Connector/Adapter for 28.58 mm outer
dia X 25 mm nominal dia threaded each 1.00 325.00 325.00
TOTAL 325.00 W
Add 1 % Water charges on "W" 3.25
TOTAL 328.25 X
Add GST on "X" (multiplying
factor 0.1405) 46.12
TOTAL 374.37 Y
Add 15% CPOH on "Y" 56.16
TOTAL 430.52 Z
Add Cess @ 1% on "Z" 4.31
Cost of 1 no. 434.83
Say 434.85
18.97.6 For 34.00 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8904 Stainless steel Male threaded
Connector/Adapter for 34.00 mm outer
dia X 25 mm nominal dia threaded each 1.00 475.00 475.00
TOTAL 475.00 W
Add 1 % Water charges on "W" 4.75
TOTAL 479.75 X
Add GST on "X" (multiplying
factor 0.1405) 67.40
TOTAL 547.15 Y
Add 15% CPOH on "Y" 82.07
TOTAL 629.23 Z
Add Cess @ 1% on "Z" 6.29
Cost of 1 no. 635.52
Say 635.50
18.97.7 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8905 Stainless steel Male threaded
Connector/Adapter for 34.00 mm outer
dia X 32 mm nominal dia threaded each 1.00 565.00 565.00
TOTAL 565.00 W
Add 1 % Water charges on "W" 5.65
TOTAL 570.65 X
SUB HEAD : 18- WATER SUPPLY 1768
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 80.18
TOTAL 650.83 Y
Add 15% CPOH on "Y" 97.62
TOTAL 748.45 Z
Add Cess @ 1% on "Z" 7.48
Cost of 1 no. 755.93
Say 755.95
18.97.8 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8906 Stainless steel Male threaded
Connector/Adapter for 42.70 mm outer
dia X 32 mm nominal dia threaded each 1.00 649.00 649.00
TOTAL 649.00 W
Add 1 % Water charges on "W" 6.49
TOTAL 655.49 X
Add GST on "X" (multiplying
factor 0.1405) 92.10
TOTAL 747.59 Y
Add 15% CPOH on "Y" 112.14
TOTAL 859.72 Z
Add Cess @ 1% on "Z" 8.60
Cost of 1 no. 868.32
Say 868.30
18.97.9 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8907 Stainless steel Male threaded
Connector/Adapter for 42.70 mm outer
dia X 40 mm nominal dia threaded each 1.00 730.00 730.00
TOTAL 730.00 W
Add 1 % Water charges on "W" 7.30
TOTAL 737.30 X
Add GST on "X" (multiplying
factor 0.1405) 103.59
TOTAL 840.89 Y
Add 15% CPOH on "Y" 126.13
TOTAL 967.02 Z
Add Cess @ 1% on "Z" 9.67
Cost of 1 no. 976.69
Say 976.70
SUB HEAD : 18- WATER SUPPLY 1769
18.97.10 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8908 Stainless steel Male threaded
Connector/Adapter for 48.60 mm outer
dia X 40 mm nominal dia threaded each 1.00 850.00 850.00
TOTAL 850.00 W
Add 1 % Water charges on "W" 8.50
TOTAL 858.50 X
Add GST on "X" (multiplying
factor 0.1405) 120.62
TOTAL 979.12 Y
Add 15% CPOH on "Y" 146.87
TOTAL 1125.99 Z
Add Cess @ 1% on "Z" 11.26
Cost of 1 no. 1137.25
Say 1137.25
18.97.11 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8909 Stainless steel Male threaded
Connector/Adapter for 48.60 mm outer
dia X 50 nominal dia threaded each 1.00 1140.00 1140.00
TOTAL 1140.00 W
Add 1 % Water charges on "W" 11.40
TOTAL 1151.40 X
Add GST on "X" (multiplying
factor 0.1405) 161.77
TOTAL 1313.17 Y
Add 15% CPOH on "Y" 196.98
TOTAL 1510.15 Z
Add Cess @ 1% on "Z" 15.10
Cost of 1 no. 1525.25
Say 1525.25
18.97A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Male Thread Connector/ Adapter
18.97A.1 For 15 mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3934 Stainless steel Male threaded
Connector/ Adapter for 15 mm outer
SUB HEAD : 18- WATER SUPPLY 1770
Code Description Unit Quantity Rate Amount
dia X 1/2" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 405.00 405.00
TOTAL 405.00 W
Add 1 % Water charges on "W" 4.05
TOTAL 409.05 X
Add GST on "X" (multiplying
factor 0.1405) 57.47
TOTAL 466.52 Y
Add 15% CPOH on "Y" 69.98
TOTAL 536.50 Z
Add Cess @ 1% on "Z" 5.36
Cost of 1 no. 541.86
Say 541.85
18.97A.2 For 22 mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3935 Stainless steel Male threaded
Connector/ Adapter for 22 mm outer
dia X 1/2" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 480.00 480.00
TOTAL 480.00 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.80 X
Add GST on "X" (multiplying
factor 0.1405) 68.11
TOTAL 552.91 Y
Add 15% CPOH on "Y" 82.94
TOTAL 635.85 Z
Add Cess @ 1% on "Z" 6.36
Cost of 1 no. 642.21
Say 642.20
18.97A.3 For 22 mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3936 Stainless steel Male threaded
Connector/ Adapter for 22 mm outer
dia X 3/4" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 505.00 505.00
TOTAL 505.00 W
Add 1 % Water charges on "W" 5.05
TOTAL 510.05 X
Add GST on "X" (multiplying
SUB HEAD : 18- WATER SUPPLY 1771
Code Description Unit Quantity Rate Amount
factor 0.1405) 71.66
TOTAL 581.71 Y
Add 15% CPOH on "Y" 87.26
TOTAL 668.97 Z
Add Cess @ 1% on "Z" 6.69
Cost of 1 no. 675.66
Say 675.65
18.97A.4 For 28 mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3937 Stainless steel Male threaded
Connector/ Adapter for 28 mm outer
dia X 1" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 665.00 665.00
TOTAL 665.00 W
Add 1 % Water charges on "W" 6.65
TOTAL 671.65 X
Add GST on "X" (multiplying
factor 0.1405) 94.37
TOTAL 766.02 Y
Add 15% CPOH on "Y" 114.90
TOTAL 880.92 Z
Add Cess @ 1% on "Z" 8.81
Cost of 1 no. 889.73
Say 889.75
18.97A.5 For 35 mm outer dia X 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3938 Stainless steel Male threaded
Connector/ Adapter for 35 mm outer
dia X 1-1/4" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 970.00 970.00
TOTAL 970.00 W
Add 1 % Water charges on "W" 9.70
TOTAL 979.70 X
Add GST on "X" (multiplying
factor 0.1405) 137.65
TOTAL 1117.35 Y
Add 15% CPOH on "Y" 167.60
TOTAL 1284.95 Z
Add Cess @ 1% on "Z" 12.85
Cost of 1 no. 1297.80
Say 1297.80
SUB HEAD : 18- WATER SUPPLY 1772
18.97A.6 For 42 mm outer dia X 1-1/2"nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3939 Stainless steel Male threaded
Connector/ Adapter for 42 mm outer
dia X 1-1/2" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1415.00 1415.00
TOTAL 1415.00 W
Add 1 % Water charges on "W" 14.15
TOTAL 1429.15 X
Add GST on "X" (multiplying
factor 0.1405) 200.80
TOTAL 1629.95 Y
Add 15% CPOH on "Y" 244.49
TOTAL 1874.44 Z
Add Cess @ 1% on "Z" 18.74
Cost of 1 no. 1893.18
Say 1893.20
18.97A.7 For 54 mm outer dia X 2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3940 Stainless steel Male threaded
Connector/ Adapter for 54 mm outer
dia X 2" nominal dia threaded of grade
316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1895.00 1895.00
TOTAL 1895.00 W
Add 1 % Water charges on "W" 18.95
TOTAL 1913.95 X
Add GST on "X" (multiplying
factor 0.1405) 268.91
TOTAL 2182.86 Y
Add 15% CPOH on "Y" 327.43
TOTAL 2510.29 Z
Add Cess @ 1% on "Z" 25.10
Cost of 1 no. 2535.39
Say 2535.40
18.98 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Valve Connector
SUB HEAD : 18- WATER SUPPLY 1773
18.98.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8910 Stainless steel Valve Connector for
15.88 mm outer dia X 15 mm nominal
dia threaded each 1.00 235.00 235.00
TOTAL 235.00 W
Add 1 % Water charges on "W" 2.35
TOTAL 237.35 X
Add GST on "X" (multiplying
factor 0.1405) 33.35
TOTAL 270.70 Y
Add 15% CPOH on "Y" 40.60
TOTAL 311.30 Z
Add Cess @ 1% on "Z" 3.11
Cost of 1 no. 314.42
Say 314.40
18.98.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8911 Stainless steel Valve Connector for
22.22 mm outer dia X 15 mm nominal
dia threaded each 1.00 280.00 280.00
TOTAL 280.00 W
Add 1 % Water charges on "W" 2.80
TOTAL 282.80 X
Add GST on "X" (multiplying
factor 0.1405) 39.73
TOTAL 322.53 Y
Add 15% CPOH on "Y" 48.38
TOTAL 370.91 Z
Add Cess @ 1% on "Z" 3.71
Cost of 1 no. 374.62
Say 374.60
18.98.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8912 Stainless steel Valve Connector for
22.22 mm outer dia X 20 mm nominal
dia threaded each 1.00 310.00 310.00
TOTAL 310.00 W
Add 1 % Water charges on "W" 3.10
TOTAL 313.10 X
SUB HEAD : 18- WATER SUPPLY 1774
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 43.99
TOTAL 357.09 Y
Add 15% CPOH on "Y" 53.56
TOTAL 410.65 Z
Add Cess @ 1% on "Z" 4.11
Cost of 1 no. 414.76
Say 414.75
18.98.4 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8913 Stainless steel Valve Connector for
28.58 mm outer dia X 25 mm nominal
dia threaded each 1.00 425.00 425.00
TOTAL 425.00 W
Add 1 % Water charges on "W" 4.25
TOTAL 429.25 X
Add GST on "X" (multiplying
factor 0.1405) 60.31
TOTAL 489.56 Y
Add 15% CPOH on "Y" 73.43
TOTAL 562.99 Z
Add Cess @ 1% on "Z" 5.63
Cost of 1 no. 568.62
Say 568.60
18.98.5 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8914 Stainless steel Valve Connector for
34.00 mm outer dia X 32 mm nominal
dia threaded each 1.00 645.00 645.00
TOTAL 645.00 W
Add 1 % Water charges on "W" 6.45
TOTAL 651.45 X
Add GST on "X" (multiplying
factor 0.1405) 91.53
TOTAL 742.98 Y
Add 15% CPOH on "Y" 111.45
TOTAL 854.43 Z
Add Cess @ 1% on "Z" 8.54
Cost of 1 no. 862.97
Say 862.95
SUB HEAD : 18- WATER SUPPLY 1775
18.98.6 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8915 Stainless steel Valve Connector for
42.70 mm outer dia X 40 mm nominal
dia threaded each 1.00 880.00 880.00
TOTAL 880.00 W
Add 1 % Water charges on "W" 8.80
TOTAL 888.80 X
Add GST on "X" (multiplying
factor 0.1405) 124.88
TOTAL 1013.68 Y
Add 15% CPOH on "Y" 152.05
TOTAL 1165.73 Z
Add Cess @ 1% on "Z" 11.66
Cost of 1 no. 1177.39
Say 1177.40
18.98.7 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8916 Stainless steel Valve Connector for
48.60 mm outer dia X 50 mm nominal
dia threaded each 1.00 1210.00 1210.00
TOTAL 1210.00 W
Add 1 % Water charges on "W" 12.10
TOTAL 1222.10 X
Add GST on "X" (multiplying
factor 0.1405) 171.71
TOTAL 1393.81 Y
Add 15% CPOH on "Y" 209.07
TOTAL 1602.88 Z
Add Cess @ 1% on "Z" 16.03
Cost of 1 no. 1618.90
Say 1618.90
18.99 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Female Threaded Elbow 90°
18.99.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8917 SS Female Threaded Elbow 90° for
15.88 mm outer dia X 15 mm nominal
dia threaded each 1.00 160.00 160.00
SUB HEAD : 18- WATER SUPPLY 1776
Code Description Unit Quantity Rate Amount
TOTAL 160.00 W
Add 1 % Water charges on "W" 1.60
TOTAL 161.60 X
Add GST on "X" (multiplying
factor 0.1405) 22.70
TOTAL 184.30 Y
Add 15% CPOH on "Y" 27.65
TOTAL 211.95 Z
Add Cess @ 1% on "Z" 2.12
Cost of 1 no. 214.07
Say 214.05
18.99.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8918 Stainless steel Female Threaded
Elbow 90° for 22.22 mm outer dia X
15 mm nominal dia threaded each 1.00 215.00 215.00
TOTAL 215.00 W
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost of 1 no. 287.66
Say 287.65
18.99.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8919 Stainless steel Female Threaded
Elbow 90° for 22.22 mm outer dia X
20 mm nominal dia threaded each 1.00 215.00 215.00
TOTAL 215.00 W
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost of 1 no. 287.66
Say 287.65
SUB HEAD : 18- WATER SUPPLY 1777
18.99.4 For 25.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8920 Stainless steel Female Threaded
Elbow 90° for 25.58 mm outer dia X
25 mm nominal dia threaded each 1.00 215.00 215.00
TOTAL 215.00 W
Add 1 % Water charges on "W" 2.15
TOTAL 217.15 X
Add GST on "X" (multiplying
factor 0.1405) 30.51
TOTAL 247.66 Y
Add 15% CPOH on "Y" 37.15
TOTAL 284.81 Z
Add Cess @ 1% on "Z" 2.85
Cost for 1 no. 287.66
Say 287.65
18.99.5 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8921 Stainless steel Female Threaded
Elbow 90° for 34.00 mm outer dia X
32 mm nominal dia threaded each 1.00 295.00 295.00
TOTAL 295.00 W
Add 1 % Water charges on "W" 2.95
TOTAL 297.95 X
Add GST on "X" (multiplying
factor 0.1405) 41.86
TOTAL 339.81 Y
Add 15% CPOH on "Y" 50.97
TOTAL 390.78 Z
Add Cess @ 1% on "Z" 3.91
Cost for 1 no. 394.69
Say 394.70
18.99.6 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8922 Stainless steel Female Threaded
Elbow 90° for 42.70 mm outer dia X
32 mm nominal dia threaded each 1.00 480.00 480.00
TOTAL 480.00 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.80 X
SUB HEAD : 18- WATER SUPPLY 1778
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 68.11
TOTAL 552.91 Y
Add 15% CPOH on "Y" 82.94
TOTAL 635.85 Z
Add Cess @ 1% on "Z" 6.36
Cost of 1 no. 642.21
Say 642.20
18.99.7 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8923 Stainless steel Female Threaded
Elbow 90° for 42.70 mm outer dia X
40 mm nominal dia threaded each 1.00 480.00 480.00
TOTAL 480.00 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.80 X
Add GST on "X" (multiplying
factor 0.1405) 68.11
TOTAL 552.91 Y
Add 15% CPOH on "Y" 82.94
TOTAL 635.85 Z
Add Cess @ 1% on "Z" 6.36
Cost of 1 no. 642.21
Say 642.20
18.99.8 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8924 Stainless steel Female Threaded
Elbow 90° for 48.60 mm outer dia X
40 mm nominal dia threaded each 1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
SUB HEAD : 18- WATER SUPPLY 1779
18.99.9 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8925 Stainless steel Female Threaded
Elbow 90° for 48.60 mm outer dia X
50 mm nominal dia threaded each
1.00 710.00 710.00
TOTAL 710.00 W
Add 1 % Water charges on "W" 7.10
TOTAL 717.10 X
Add GST on "X" (multiplying
factor 0.1405) 100.75
TOTAL 817.85 Y
Add 15% CPOH on "Y" 122.68
TOTAL 940.53 Z
Add Cess @ 1% on "Z" 9.41
Cost of 1 no. 949.94
Say 949.95
18.99A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Female Threaded Elbow 90°
18.99A.1 For 15 mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3941 Stainless steel Female Threaded
Elbow 90° for 15 mm outer dia X 1/2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 640.00 640.00
TOTAL 640.00 W
Add 1 % Water charges on "W" 6.40
TOTAL 646.40 X
Add GST on "X" (multiplying
factor 0.1405) 90.82
TOTAL 737.22 Y
Add 15% CPOH on "Y" 110.58
TOTAL 847.80 Z
Add Cess @ 1% on "Z" 8.48
Cost of 1 no. 856.28
Say 856.30
SUB HEAD : 18- WATER SUPPLY 1780
18.99A.2 For 22 mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3942 Stainless steel Female Threaded
Elbow 90° for 22 mm outer dia X 3/4"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 860.00 860.00
TOTAL 860.00 W
Add 1 % Water charges on "W" 8.60
TOTAL 868.60 X
Add GST on "X" (multiplying
factor 0.1405) 122.04
TOTAL 990.64 Y
Add 15% CPOH on "Y" 148.60
TOTAL 1139.23 Z
Add Cess @ 1% on "Z" 11.39
Cost of 1 no. 1150.63
Say 1150.65
18.99A.3 For 28mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3943 Stainless steel Female Threaded
Elbow 90° for 28mm outer dia X 1"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 1180.00 1180.00
TOTAL 1180.00 W
Add 1 % Water charges on "W" 11.80
TOTAL 1191.80 X
Add GST on "X" (multiplying
factor 0.1405) 167.45
TOTAL 1359.25 Y
Add 15% CPOH on "Y" 203.89
TOTAL 1563.14 Z
Add Cess @ 1% on "Z" 15.63
Cost for 1 no. 1578.77
Say 1578.75
18.99A.4 For 35mm outer dia X 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3944 Stainless steel Female Threaded
Elbow 90° for 35mm outer dia X 1-1/4"
SUB HEAD : 18- WATER SUPPLY 1781
Code Description Unit Quantity Rate Amount
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 1917.00 1917.00
TOTAL 1917.00 W
Add 1 % Water charges on "W" 19.17
TOTAL 1936.17 X
Add GST on "X" (multiplying
factor 0.1405) 272.03
TOTAL 2208.20 Y
Add 15% CPOH on "Y" 331.23
TOTAL 2539.43 Z
Add Cess @ 1% on "Z" 25.39
Cost for 1 no. 2564.83
Say 2564.85
18.99A.5 For 42mm outer dia X 1-1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3945 Stainless steel Female Threaded
Elbow 90° for 42mm outer dia X 1-1/2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 2088.00 2088.00
TOTAL 2088.00 W
Add 1 % Water charges on "W" 20.88
TOTAL 2108.88 X
Add GST on "X" (multiplying
factor 0.1405) 296.30
TOTAL 2405.18 Y
Add 15% CPOH on "Y" 360.78
TOTAL 2765.95 Z
Add Cess @ 1% on "Z" 27.66
Cost of 1 no. 2793.61
Say 2793.60
18.99A.6 For 54mm outer dia X 2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3946 Stainless steel Female Threaded
Elbow 90° for 54mm outer dia X 2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 3227.00 3227.00
TOTAL 3227.00 W
Add 1 % Water charges on "W" 32.27
TOTAL 3259.27 X
Add GST on "X" (multiplying
factor 0.1405) 457.93
SUB HEAD : 18- WATER SUPPLY 1782
Code Description Unit Quantity Rate Amount
TOTAL 3717.20 Y
Add 15% CPOH on "Y" 557.58
TOTAL 4274.78 Z
Add Cess @ 1% on "Z" 42.75
Cost of 1 no. 4317.52
Say 4317.50
18.100 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Male Threaded Elbow 90°
18.100.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8926 Stainless steel Male Threaded Elbow
90° for 15.88 mm outer dia X 15 mm
nominal dia threaded each 1.00 195.00 195.00
TOTAL 195.00 W
Add 1 % Water charges on "W" 1.95
TOTAL 196.95 X
Add GST on "X" (multiplying
factor 0.1405) 27.67
TOTAL 224.62 Y
Add 15% CPOH on "Y" 33.69
TOTAL 258.31 Z
Add Cess @ 1% on "Z" 2.58
Cost of 1 no. 260.90
Say 260.90
18.100.2 For 22.22 mm outer dia x 15 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8927 Stainless steel Male Threaded Elbow
90° for 22.22 mm outer dia X 15 mm
nominal dia threaded each 1.00 225.00 225.00
TOTAL 225.00 W
Add 1 % Water charges on "W" 2.25
TOTAL 227.25 X
Add GST on "X" (multiplying
factor 0.1405) 31.93
TOTAL 259.18 Y
Add 15% CPOH on "Y" 38.88
TOTAL 298.06 Z
Add Cess @ 1% on "Z" 2.98
Cost of 1 no. 301.04
Say 301.05
SUB HEAD : 18- WATER SUPPLY 1783
18.100.3 For 22.22 mm outer dia x 20 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8928 Stainless steel Male Threaded Elbow
90° for 22.22 mm outer dia X 20 mm
nominal dia threaded each 1.00 225.00 225.00
TOTAL 225.00 W
Add 1 % Water charges on "W" 2.25
TOTAL 227.25 X
Add GST on "X" (multiplying
factor 0.1405) 31.93
TOTAL 259.18 Y
Add 15% CPOH on "Y" 38.88
TOTAL 298.06 Z
Add Cess @ 1% on "Z" 2.98
Cost of 1 no. 301.04
Say 301.05
18.100.4 For 28.58 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8929 Stainless steel Male Threaded Elbow
90° for 28.58 mm outer dia X 25 mm
nominal dia threaded each 1.00 225.00 225.00
TOTAL 225.00 W
Add 1 % Water charges on "W" 2.25
TOTAL 227.25 X
Add GST on "X" (multiplying
factor 0.1405) 31.93
TOTAL 259.18 Y
Add 15% CPOH on "Y" 38.88
TOTAL 298.06 Z
Add Cess @ 1% on "Z" 2.98
Cost of 1 no. 301.04
Say 301.05
18.100.5 For 34.00 mm outer dia x 25 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8930 Stainless steel Male Threaded Elbow
90° for 34.00 mm outer dia X 25 mm
nominal dia threaded each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
SUB HEAD : 18- WATER SUPPLY 1784
Code Description Unit Quantity Rate Amount
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
18.100.6 For 34.00 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8931 Stainless steel Male Threaded Elbow
90° for 34.00 mm outer dia X 32 mm
nominal dia threaded each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
18.100.7 For 42.70 mm outer dia x 32 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8932 Stainless steel Male Threaded Elbow
90° for 42.70 mm outer dia X 32 mm
nominal dia threaded each 1.00 480.00 480.00
TOTAL 480.00 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.80 X
Add GST on "X" (multiplying
factor 0.1405) 68.11
TOTAL 552.91 Y
Add 15% CPOH on "Y" 82.94
TOTAL 635.85 Z
Add Cess @ 1% on "Z" 6.36
Cost of 1 no. 642.21
Say 642.20
SUB HEAD : 18- WATER SUPPLY 1785
18.100.8 For 42.70 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8933 Stainless steel Male Threaded Elbow
90° for 42.70 mm outer dia X40 mm
nominal dia threaded each 1.00 480.00 480.00
TOTAL 480.00 W
Add 1 % Water charges on "W" 4.80
TOTAL 484.80 X
Add GST on "X" (multiplying
factor 0.1405) 68.11
TOTAL 552.91 Y
Add 15% CPOH on "Y" 82.94
TOTAL 635.85 Z
Add Cess @ 1% on "Z" 6.36
Cost of 1 no. 642.21
Say 642.20
18.100.9 For 48.60 mm outer dia x 40 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8934 Stainless steel Male Threaded Elbow
90° for 48.60 mm outer dia X 40 mm
nominal dia threaded each 1.00 695.00 695.00
TOTAL 695.00 W
Add 1 % Water charges on "W" 6.95
TOTAL 701.95 X
Add GST on "X" (multiplying
factor 0.1405) 98.62
TOTAL 800.57 Y
Add 15% CPOH on "Y" 120.09
TOTAL 920.66 Z
Add Cess @ 1% on "Z" 9.21
Cost of 1 no. 929.87
Say 929.85
18.100.10 For 48.60 mm outer dia x 50 mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8935 Stainless steel Male Threaded Elbow
90° for 48.60 mm outer dia X 50 mm
nominal dia threaded each 1.00 695.00 695.00
TOTAL 695.00 W
Add 1 % Water charges on "W" 6.95
TOTAL 701.95 X
SUB HEAD : 18- WATER SUPPLY 1786
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 98.62
TOTAL 800.57 Y
Add 15% CPOH on "Y" 120.09
TOTAL 920.66 Z
Add Cess @ 1% on "Z" 9.21
Cost of 1 no. 929.87
Say 929.85
18.100.A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Male Threaded Elbow 90°
18.100A.1 For 15mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3947 Stainless steel Male Threaded Elbow
90° for 15mm outer dia X 1/2" nominal
dia threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 525.00 525.00
TOTAL 525.00 W
Add 1 % Water charges on "W" 5.25
TOTAL 530.25 X
Add GST on "X" (multiplying
factor 0.1405) 74.50
TOTAL 604.75 Y
Add 15% CPOH on "Y" 90.71
TOTAL 695.46 Z
Add Cess @ 1% on "Z" 6.95
Cost of 1 no. 702.42
Say 702.40
18.100A.2 For 22mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3948 Stainless steel Male Threaded Elbow
90° for 22mm outer dia X 3/4" nominal
dia threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 790.00 790.00
TOTAL 790.00 W
Add 1 % Water charges on "W" 7.90
TOTAL 797.90 X
SUB HEAD : 18- WATER SUPPLY 1787
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 112.10
TOTAL 910.00 Y
Add 15% CPOH on "Y" 136.50
TOTAL 1046.51 Z
Add Cess @ 1% on "Z" 10.47
Cost of 1 no. 1056.97
Say 1056.95
18.100A.3 For 28mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3949 Stainless steel Male Threaded Elbow
90° for 28mm outer dia X 1" nominal
dia threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1045.00 1045.00
TOTAL 1045.00 W
Add 1 % Water charges on "W" 10.45
TOTAL 1055.45 X
Add GST on "X" (multiplying
factor 0.1405) 148.29
TOTAL 1203.74 Y
Add 15% CPOH on "Y" 180.56
TOTAL 1384.30 Z
Add Cess @ 1% on "Z" 13.84
Cost of 1 no. 1398.14
Say 1398.15
18.100A.4 For 35mm outer dia X 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3950 Stainless steel Male Threaded Elbow
90° for 35mm outer dia X 1-1/4"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 1440.00 1440.00
TOTAL 1440.00 W
Add 1 % Water charges on "W" 14.40
TOTAL 1454.40 X
Add GST on "X" (multiplying
factor 0.1405) 204.34
TOTAL 1658.74 Y
Add 15% CPOH on "Y" 248.81
TOTAL 1907.55 Z
Add Cess @ 1% on "Z" 19.08
Cost of 1 no. 1926.63
Say 1926.65
SUB HEAD : 18- WATER SUPPLY 1788
18.100A.5 For 42mm outer dia X 1-1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3951 Stainless steel Male Threaded Elbow
90° for 42mm outer dia X 1-1/2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 2635.00 2635.00
TOTAL 2635.00 W
Add 1 % Water charges on "W" 26.35
TOTAL 2661.35 X
Add GST on "X" (multiplying
factor 0.1405) 373.92
TOTAL 3035.27 Y
Add 15% CPOH on "Y" 455.29
TOTAL 3490.56 Z
Add Cess @ 1% on "Z" 34.91
Cost of 1 no. 3525.47
Say 3525.45
18.100A.6 For 54mm outer dia X 2" mm nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3952 Stainless steel Male Threaded Elbow
90° for 54mm outer dia X 2" nominal
dia threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 2998.00 2998.00
TOTAL 2998.00 W
Add 1 % Water charges on "W" 29.98
TOTAL 3027.98 X
Add GST on "X" (multiplying
factor 0.1405) 425.43
TOTAL 3453.41 Y
Add 15% CPOH on "Y" 518.01
TOTAL 3971.42 Z
Add Cess @ 1% on "Z" 39.71
Cost of 1 no. 4011.14
Say 4011.15
18.101 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Cap
SUB HEAD : 18- WATER SUPPLY 1789
18.101.1 For 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8936 Stainless steel Cap for 15.88 mm
outer dia pipe each 1.00 48.00 48.00
TOTAL 48.00 W
Add 1 % Water charges on "W" 0.48
TOTAL 48.48 X
Add GST on "X" (multiplying
factor 0.1405) 6.81
TOTAL 55.29 Y
Add 15% CPOH on "Y" 8.29
TOTAL 63.59 Z
Add Cess @ 1% on "Z" 0.64
Cost of 1 no. 64.22
Say 64.20
18.101.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8937 Stainless steel Cap for 22.22 mm
outer dia pipe each 1.00 70.00 70.00
TOTAL 70.00 W
Add 1 % Water charges on "W" 0.70
TOTAL 70.70 X
Add GST on "X" (multiplying
factor 0.1405) 9.93
TOTAL 80.63 Y
Add 15% CPOH on "Y" 12.10
TOTAL 92.73 Z
Add Cess @ 1% on "Z" 0.93
Cost of 1 no. 93.66
Say 93.65
18.101.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8938 Stainless steel Cap for 28.58 mm
outer dia pipe each 1.00 90.00 90.00
TOTAL 90.00 W
Add 1 % Water charges on "W" 0.90
TOTAL 90.90 X
Add GST on "X" (multiplying
factor 0.1405) 12.77
TOTAL 103.67 Y
Add 15% CPOH on "Y" 15.55
TOTAL 119.22 Z
Add Cess @ 1% on "Z" 1.19
Cost of 1 no. 120.41
Say 120.40
SUB HEAD : 18- WATER SUPPLY 1790
18.101.4 For 34.00 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8939 Stainless steel Cap for 34.00 mm
outer dia pipe each 1.00 175.00 175.00
TOTAL 175.00 W
Add 1 % Water charges on "W" 1.75
TOTAL 176.75 X
Add GST on "X" (multiplying
factor 0.1405) 24.83
TOTAL 201.58 Y
Add 15% CPOH on "Y" 30.24
TOTAL 231.82 Z
Add Cess @ 1% on "Z" 2.32
Cost of 1 no. 234.14
Say 234.15
18.101.5 For 42.70 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8940 Stainless steel Cap for 42.70 mm
outer dia pipe each 1.00 250.00 250.00
TOTAL 250.00 W
Add 1 % Water charges on "W" 2.50
TOTAL 252.50 X
Add GST on "X" (multiplying
factor 0.1405) 35.48
TOTAL 287.98 Y
Add 15% CPOH on "Y" 43.20
TOTAL 331.17 Z
Add Cess @ 1% on "Z" 3.31
Cost of 1 no. 334.48
Say 334.50
18.101.6 For 48.60 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8941 Stainless steel Cap for 48.60 mm
outer dia pipe each 1.00 325.00 325.00
TOTAL 325.00 W
Add 1 % Water charges on "W" 3.25
TOTAL 328.25 X
Add GST on "X" (multiplying
factor 0.1405) 46.12
TOTAL 374.37 Y
Add 15% CPOH on "Y" 56.16
TOTAL 430.52 Z
Add Cess @ 1% on "Z" 4.31
Cost of 1 no. 434.83
Say 434.85
SUB HEAD : 18- WATER SUPPLY 1791
18.101A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Cap
18.101A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3953 Stainless steel Cap for 15 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 320.00 320.00
TOTAL 320.00 W
Add 1 % Water charges on "W" 3.20
TOTAL 323.20 X
Add GST on "X" (multiplying
factor 0.1405) 45.41
TOTAL 368.61 Y
Add 15% CPOH on "Y" 55.29
TOTAL 423.90 Z
Add Cess @ 1% on "Z" 4.24
Cost of 1 no. 428.14
Say 428.15
18.101A.2 For 22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3954 Stainless steel Cap for 22 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 415.00 415.00
TOTAL 415.00 W
Add 1 % Water charges on "W" 4.15
TOTAL 419.15 X
Add GST on "X" (multiplying
factor 0.1405) 58.89
TOTAL 478.04 Y
Add 15% CPOH on "Y" 71.71
TOTAL 549.75 Z
Add Cess @ 1% on "Z" 5.50
Cost of 1 no. 555.24
Say 555.25
18.101A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
SUB HEAD : 18- WATER SUPPLY 1792
Code Description Unit Quantity Rate Amount
3955 Stainless steel Cap for 28 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 515.00 515.00
TOTAL 515.00 W
Add 1 % Water charges on "W" 5.15
TOTAL 520.15 X
Add GST on "X" (multiplying
factor 0.1405) 73.08
TOTAL 593.23 Y
Add 15% CPOH on "Y" 88.98
TOTAL 682.22 Z
Add Cess @ 1% on "Z" 6.82
Cost of 1 no. 689.04
Say 689.05
18.101A.4 For 35 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3956 Stainless steel Cap for 35 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 720.00 720.00
TOTAL 720.00 W
Add 1 % Water charges on "W" 7.20
TOTAL 727.20 X
Add GST on "X" (multiplying
factor 0.1405) 102.17
TOTAL 829.37 Y
Add 15% CPOH on "Y" 124.41
TOTAL 953.78 Z
Add Cess @ 1% on "Z" 9.54
Cost of 1 no. 963.32
Say 963.30
18.101A.5 For 42 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3957 Stainless steel Cap for 42 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1565.00 1565.00
TOTAL 1565.00 W
Add 1 % Water charges on "W" 15.65
TOTAL 1580.65 X
SUB HEAD : 18- WATER SUPPLY 1793
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 222.08
TOTAL 1802.73 Y
Add 15% CPOH on "Y" 270.41
TOTAL 2073.14 Z
Add Cess @ 1% on "Z" 20.73
Cost of 1 no. 2093.87
Say 2093.85
18.101A.6 For 54 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3958 Stainless steel Cap for 54 mm outer
dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1720.00 1720.00
TOTAL 1720.00 W
Add 1 % Water charges on "W" 17.20
TOTAL 1737.20 X
Add GST on "X" (multiplying
factor 0.1405) 244.08
TOTAL 1981.28 Y
Add 15% CPOH on "Y" 297.19
TOTAL 2278.47 Z
Add Cess @ 1% on "Z" 22.78
Cost of 1 no. 2301.25
Say 2301.25
18.102 Providing and fixing required Stainless Steel Fitting of press fit design of grade
AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and
with O-ring sealing gasket of EPDM material of required dia as per direction of
Engineer-in-charge.
Pipe Bridge
18.102.1 For 15.88 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8942 Stainless steel Pipe Bridge for
15.88 mm outer dia pipe each 1.00 220.00 220.00
TOTAL 220.00 W
Add 1 % Water charges on "W" 2.20
TOTAL 222.20 X
Add GST on "X" (multiplying
factor 0.1405) 31.22
TOTAL 253.42 Y
Add 15% CPOH on "Y" 38.01
TOTAL 291.43 Z
Add Cess @ 1% on "Z" 2.91
Cost of 1 no. 294.35
Say 294.35
SUB HEAD : 18- WATER SUPPLY 1794
18.102.2 For 22.22 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8943 Stainless steel Pipe Bridge for
15.88 mm outer dia pipe each 1.00 290.00 290.00
TOTAL 290.00 W
Add 1 % Water charges on "W" 2.90
TOTAL 292.90 X
Add GST on "X" (multiplying
factor 0.1405) 41.15
TOTAL 334.05 Y
Add 15% CPOH on "Y" 50.11
TOTAL 384.16 Z
Add Cess @ 1% on "Z" 3.84
Cost of 1 no. 388.00
Say 388.00
18.102.3 For 28.58 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
8944 Stainless steel Pipe Bridge for
28.58 mm outer dia pipe each 1.00 415.00 415.00
TOTAL 415.00 W
Add 1 % Water charges on "W" 4.15
TOTAL 419.15 X
Add GST on "X" (multiplying
factor 0.1405) 58.89
TOTAL 478.04 Y
Add 15% CPOH on "Y" 71.71
TOTAL 549.75 Z
Add Cess @ 1% on "Z" 5.50
Cost for 1 no. 555.24
Say 555.25
18.102A Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Pipe Bridge
18.102A.1 For 15 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3959 Stainless steel Pipe Bridge for 15 mm
outer dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 415.00 415.00
SUB HEAD : 18- WATER SUPPLY 1795
Code Description Unit Quantity Rate Amount
TOTAL 415.00 W
Add 1 % Water charges on "W" 4.15
TOTAL 419.15 X
Add GST on "X" (multiplying
factor 0.1405) 58.89
TOTAL 478.04 Y
Add 15% CPOH on "Y" 71.71
TOTAL 549.75 Z
Add Cess @ 1% on "Z" 5.50
Cost of 1 no. 555.24
Say 555.25
18.102A.3 For 28 mm outer dia pipe
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3961 Stainless steel Pipe Bridge for 28 mm
outer dia pipe of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1526.00 1526.00
TOTAL 1526.00 W
Add 1 % Water charges on "W" 15.26
TOTAL 1541.26 X
Add GST on "X" (multiplying
factor 0.1405) 216.55
TOTAL 1757.81 Y
Add 15% CPOH on "Y" 263.67
TOTAL 2021.48 Z
Add Cess @ 1% on "Z" 20.21
Cost for 1 no. 2041.69
Say 2041.70
18.103 Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Male Union
18.103.1 For 15mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3962 Stainless steel Male Union for 15mm
outer dia X 1/2" nominal dia threaded
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 885.00 885.00
TOTAL 885.00 W
Add 1 % Water charges on "W" 8.85
TOTAL 893.85 X
SUB HEAD : 18- WATER SUPPLY 1796
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 125.59
TOTAL 1019.44 Y
Add 15% CPOH on "Y" 152.92
TOTAL 1172.35 Z
Add Cess @ 1% on "Z" 11.72
Cost of 1 no. 1184.07
Say 1184.05
18.103.2 For 22mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3963 Stainless steel Male Union for 22mm
outer dia X 1/2" nominal dia threaded
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 895.00 895.00
TOTAL 895.00 W
Add 1 % Water charges on "W" 8.95
TOTAL 903.95 X
Add GST on "X" (multiplying
factor 0.1405) 127.00
TOTAL 1030.95 Y
Add 15% CPOH on "Y" 154.64
TOTAL 1185.60 Z
Add Cess @ 1% on "Z" 11.86
Cost of 1 no. 1197.45
Say 1197.45
18.103.3 For 22mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3964 Stainless steel Male Union for 22mm
outer dia X 3/4" nominal dia threaded
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1025.00 1025.00
TOTAL 1025.00 W
Add 1 % Water charges on "W" 10.25
TOTAL 1035.25 X
Add GST on "X" (multiplying
factor 0.1405) 145.45
TOTAL 1180.70 Y
Add 15% CPOH on "Y" 177.11
TOTAL 1357.81 Z
Add Cess @ 1% on "Z" 13.58
Cost of 1 no. 1371.39
Say 1371.40
SUB HEAD : 18- WATER SUPPLY 1797
18.103.4 For 28mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3965 Stainless steel Male Union for 28mm
outer dia X 1" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1805.00 1805.00
TOTAL 1805.00 W
Add 1 % Water charges on "W" 18.05
TOTAL 1823.05 X
Add GST on "X" (multiplying
factor 0.1405) 256.14
TOTAL 2079.19 Y
Add 15% CPOH on "Y" 311.88
TOTAL 2391.07 Z
Add Cess @ 1% on "Z" 23.91
Cost of 1 no. 2414.98
Say 2415.00
18.103.5 For 35mm outer dia X 1-1/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3966 Stainless steel Male Union for 35mm
outer dia X 1-1/4" nominal dia threaded
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 1885.00 1885.00
TOTAL 1885.00 W
Add 1 % Water charges on "W" 18.85
TOTAL 1903.85 X
Add GST on "X" (multiplying
factor 0.1405) 267.49
TOTAL 2171.34 Y
Add 15% CPOH on "Y" 325.70
TOTAL 2497.04 Z
Add Cess @ 1% on "Z" 24.97
Cost of 1 no. 2522.01
Say 2522.00
18.103.6 For 42mm outer dia X 1-1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3967 Stainless steel Male Union for 42mm
outer dia X 1-1/2" nominal dia threaded
of grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 2130.00 2130.00
TOTAL 2130.00 W
SUB HEAD : 18- WATER SUPPLY 1798
Code Description Unit Quantity Rate Amount
Add 1 % Water charges on "W" 21.30
TOTAL 2151.30 X
Add GST on "X" (multiplying
factor 0.1405) 302.26
TOTAL 2453.56 Y
Add 15% CPOH on "Y" 368.03
TOTAL 2821.59 Z
Add Cess @ 1% on "Z" 28.22
Cost of 1 no. 2849.81
Say 2849.80
18.103.7 For 54mm outer dia X 2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3968 Stainless steel Male Union for 54mm
outer dia X 2" nominal dia threaded of
grade 316L as per IS 6911:2017 and
conforming to EN-10312 each 1.00 3680.00 3680.00
TOTAL 3680.00 W
Add 1 % Water charges on "W" 36.80
TOTAL 3716.80 X
Add GST on "X" (multiplying
factor 0.1405) 522.21
TOTAL 4239.01 Y
Add 15% CPOH on "Y" 635.85
TOTAL 4874.86 Z
Add Cess @ 1% on "Z" 48.75
Cost of 1 no. 4923.61
Say 4923.60
18.104 Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Female Union
18.104.1 For 22 mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3969 Stainless steel Female Union for
22 mm outer dia X 3/4" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 950.00 950.00
TOTAL 950.00 W
Add 1 % Water charges on "W" 9.50
TOTAL 959.50 X
SUB HEAD : 18- WATER SUPPLY 1799
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 134.81
TOTAL 1094.31 Y
Add 15% CPOH on "Y" 164.15
TOTAL 1258.46 Z
Add Cess @ 1% on "Z" 12.58
Cost of 1 no. 1271.04
Say 1271.05
18.104.2 For 28mm outer dia X 1" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3970 Stainless steel Female Union for
28mm outer dia X 1" nominal dia
threaded of grade 316L as per IS
6911:2017 and conforming to
EN-10312 each 1.00 1280.00 1280.00
TOTAL 1280.00 W
Add 1 % Water charges on "W" 12.80
TOTAL 1292.80 X
Add GST on "X" (multiplying
factor 0.1405) 181.64
TOTAL 1474.44 Y
Add 15% CPOH on "Y" 221.17
TOTAL 1695.60 Z
Add Cess @ 1% on "Z" 16.96
Cost of 1 no. 1712.56
Say 1712.55
18.105 Providing and fixing required Stainless Steel Fitting of press fit design of grade
316L as per IS 6911:2017 and conforming to EN-10312 standard with V-profile
and with O-ring sealing gasket of EPDM material of required dia as per direction
of Engineer-in-charge.
Female Transition Elbow / FTE
18.105.1 For 15mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3971 Stainless steel Female Transition
Elbow / FTE for 15mm outer dia X 1/2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 649.00 649.00
TOTAL 649.00 W
Add 1 % Water charges on "W" 6.49
TOTAL 655.49 X
Add GST on "X" (multiplying
factor 0.1405) 92.10
SUB HEAD : 18- WATER SUPPLY 1800
Code Description Unit Quantity Rate Amount
TOTAL 747.59 Y
Add 15% CPOH on "Y" 112.14
TOTAL 859.72 Z
Add Cess @ 1% on "Z" 8.60
Cost of 1 no. 868.32
Say 868.30
18.105.2 For 22mm outer dia X 1/2" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3972 Stainless steel Female Transition
Elbow / FTE for 22mm outer dia X 1/2"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 900.00 900.00
TOTAL 900.00 W
Add 1 % Water charges on "W" 9.00
TOTAL 909.00 X
Add GST on "X" (multiplying
factor 0.1405) 127.71
TOTAL 1036.71 Y
Add 15% CPOH on "Y" 155.51
TOTAL 1192.22 Z
Add Cess @ 1% on "Z" 11.92
Cost of 1 no. 1204.14
Say 1204.15
18.105.3 For 22mm outer dia X 3/4" nominal dia threaded
Code Description Unit Quantity Rate Amount
Details of cost for 1 no.
MATERIAL
3973 Stainless steel Female Transition
Elbow / FTE for 22mm outer dia X 3/4"
nominal dia threaded of grade 316L as
per IS 6911:2017 and conforming to
EN-10312 each 1.00 870.00 870.00
TOTAL 870.00 W
Add 1 % Water charges on "W" 8.70
TOTAL 878.70 X
Add GST on "X" (multiplying
factor 0.1405) 123.46
TOTAL 1002.16 Y
Add 15% CPOH on "Y" 150.32
TOTAL 1152.48 Z
Add Cess @ 1% on "Z" 11.52
Cost of 1 no. 1164.01
Say 1164.00
SUB HEAD : 18- WATER SUPPLY 1801
SUB HEAD : 19.0
DRAINAGE
1803
19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff
mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand)
including testing of joints etc. complete :
19.1.1 100 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
1854 Stoneware pipes grade A (60 cm long)
100 mm dia each 55.00 70.00 3850.00
Added 10% allowance for breakage
2224 Carriage of S.W. pipes 100 mm dia 100 metre 0.33 218.58 72.13
Added 10% allowance for breakage
Cement for 50 joints = 0.019 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.019 5000.00 95.00
2209 Carriage of Cement tonne 0.019 145.72 2.77
0983 Fine sand (zone IV) cum 0.01 900.00 9.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.01 163.93 1.64
1881 Spun yarn kilogram 4.50 55.00 247.50
or plain gaskin @ 0.09 kg per joint
= 0.09x50 = 4.50 kg
LABOUR
0123 Mason (brick layer) 1st class day 1.00 784.00 784.00
0124 Mason (brick layer) 2nd class day 1.00 714.00 714.00
0114 Beldar day 3.00 645.00 1935.00
0101 Bhisti day 1.00 714.00 714.00
TOTAL 8425.04 W
Add 1 % Water charges on "W" 84.25
TOTAL 8509.29 X
Add GST on "X" (multiplying
factor 0.1405) 1195.56
TOTAL 9704.84 Y
Add 15% CPOH on "Y" 1455.73
TOTAL 11160.57 Z
Add Cess @ 1% on "Z" 111.61
Cost of 30 metre 11272.18
Cost of 1 metre 375.74
Say 375.75
19.1.2 150 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
1855 Stoneware pipes grade A (60 cm long)
150 mm dia each 55.00 125.00 6875.00
Added 10% allowance for breakage
2225 Carriage of S.W. pipes 150 mm dia 100 metre 0.33 437.15 144.26
Added 10% allowance for breakage
Cement of 50 joints = 0.036 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.036 5000.00 180.00
SUB HEAD : 19- DRAINAGE 1805
Code Description Unit Quantity Rate Amount
2209 Carriage of Cement tonne 0.036 145.72 5.25
0983 Fine sand (zone IV) cum 0.019 900.00 17.10
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.019 163.93 3.11
1881 Spun yarn kilogram 9.00 55.00 495.00
or plain gaskin @ 0.18 kg per joint
= 0.18x50 = 9 kg
LABOUR
0123 Mason (brick layer) 1st class day 1.50 784.00 1176.00
0124 Mason (brick layer) 2nd class day 1.50 714.00 1071.00
0114 Beldar day 4.00 645.00 2580.00
0101 Bhisti day 1.00 714.00 714.00
TOTAL 13260.72 W
Add 1 % Water charges on "W" 132.61
TOTAL 13393.33 X
Add GST on "X" (multiplying
factor 0.1405) 1881.76
TOTAL 15275.09 Y
Add 15% CPOH on "Y" 2291.26
TOTAL 17566.35 Z
Add Cess @ 1% on "Z" 175.66
Cost of 30 metre 17742.02
Cost of 1 metre 591.40
Say 591.40
19.1.3 200 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
1856 Stoneware pipes grade A (60 cm long)
200 mm dia each 55.00 200.00 11000.00
Added 10% allowance for breakage
2226 Carriage of S.W. pipes 200 mm dia 100 metre 0.33 728.59 240.43
Added 10% allowance for breakage
Cement of 50 joints = 0.053 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.053 5000.00 265.00
2209 Carriage of Cement tonne 0.053 145.72 7.72
0983 Fine sand (zone IV) cum 0.028 900.00 25.20
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.028 163.93 4.59
1881 Spun yarn kilogram 12.00 55.00 660.00
or plain gaskin @ 0.24 kg per joint
= 0.24x50 =12.00 kg
LABOUR
0123 Mason (brick layer) 1st class day 1.75 784.00 1372.00
0124 Mason (brick layer) 2nd class day 1.75 714.00 1249.50
0114 Beldar day 4.50 645.00 2902.50
SUB HEAD : 19- DRAINAGE 1806
Code Description Unit Quantity Rate Amount
0101 Bhisti day 1.25 714.00 892.50
TOTAL 18619.45 W
Add 1 % Water charges on "W" 186.19
TOTAL 18805.64 X
Add GST on "X" (multiplying
factor 0.1405) 2642.19
TOTAL 21447.84 Y
Add 15% CPOH on "Y" 3217.18
TOTAL 24665.01 Z
Add Cess @ 1% on "Z" 246.65
Cost of 30 metre 24911.66
Cost of 1 metre 830.39
Say 830.40
19.1.4 250 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
1858 Stoneware pipes grade A (60 cm long)
250 mm dia each 55.00 350.00 19250.00
Added 10% allowance for breakage
2228 Carriage of S.W. pipes 250 mm dia 100 metre 0.33 1249.01 412.17
Added 10% allowance for breakage
Cement of 50 joints = 0.094 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.094 5000.00 470.00
2209 Carriage of Cement tonne 0.094 145.72 13.70
0983 Fine sand (zone IV) cum 0.05 900.00 45.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.05 163.93 8.20
1881 Spun yarn kilogram 15.00 55.00 825.00
or plain gaskin @ 0.30 kg per joint
= 0.30x50= 15.00 kg
LABOUR
0123 Mason (brick layer) 1st class day 2.25 784.00 1764.00
0124 Mason (brick layer) 2nd class day 2.25 714.00 1606.50
0114 Beldar day 5.50 645.00 3547.50
0101 Bhisti day 1.50 714.00 1071.00
TOTAL 29013.07 W
Add 1 % Water charges on "W" 290.13
TOTAL 29303.20 X
Add GST on "X" (multiplying
factor 0.1405) 4117.10
TOTAL 33420.30 Y
Add 15% CPOH on "Y" 5013.04
TOTAL 38433.34 Z
Add Cess @ 1% on "Z" 384.33
Cost of 30 metre 38817.68
Cost of 1 metre 1293.92
Say 1293.90
SUB HEAD : 19- DRAINAGE 1807
19.1.5 300 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
1859 Stoneware pipes grade A (60 cm long)
300 mm dia each 55.00 525.00 28875.00
Added 10% allowance for breakage
2229 Carriage of S.W. pipes 300 mm dia 100 metre 0.33 1561.26 515.22
Added 10% allowance for breakage
Cement of 50 joints = 0.125 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.125 5000.00 625.00
2209 Carriage of Cement tonne 0.125 145.72 18.22
0983 Fine sand (zone IV) cum 0.075 900.00 67.50
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.075 163.93 12.29
1881 Spun yarn kilogram 18.00 55.00 990.00
or plain gaskin @ 0.36 kg / joint
= 0.36x50 =18.00 kg
LABOUR
0123 Mason (brick layer) 1st class day 2.50 784.00 1960.00
0124 Mason (brick layer) 2nd class day 2.50 714.00 1785.00
0114 Beldar day 6.00 645.00 3870.00
0101 Bhisti day 1.50 714.00 1071.00
TOTAL 39789.23 W
Add 1 % Water charges on "W" 397.89
TOTAL 40187.12 X
Add GST on "X" (multiplying
factor 0.1405) 5646.29
TOTAL 45833.41 Y
Add 15% CPOH on "Y" 6875.01
TOTAL 52708.42 Z
Add Cess @ 1% on "Z" 527.08
Cost of 30 metre 53235.50
Cost of 1 metre 1774.52
Say 1774.50
19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10
graded stone aggregate 40 mm nominal size) all-round S.W. pipes including
bed concrete as per standard design :
19.2.1 100 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Area = W x W/2 + ½ x (3.14 x W² / 4) -
(3.14 x D² / 4)
= W² x (0.5 + 3.14 / 8) - (3.14 x D² / 4)
Where W = D + X
D = 100 + 12 + 12 = 124 mm or 12.4 cm
X = 300 mm as trench depth is less
than 1200 mm
SUB HEAD : 19- DRAINAGE 1808
Code Description Unit Quantity Rate Amount
W = 12.4 + 30 = 42.4
Area= 42.4² x ( 0.5 + 3.14/ 8) -
(3.14 x 12.4²/4)
= 1484 sqcm = 0.1484 sqm
Say 0.148 sqm
For 10 m length qty. of concrete reqd.
= 1.48 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.48 6050.65 8954.96 A
Cost of 10 metres 8954.96
Cost of metre 895.50
Say 895.50
19.2.2 150 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Area = W x W/2 + ½ x (3.14 x W² / 4)-
(3.14 x D² / 4)
= W² x (0.5 + 3.14 / 8) - (3.14 x D² / 4)
Where W = D + X
D = 150 + 16 + 16 = 182 mm or 18.2 cm
X = 300 mm as trench depth is less
than 1200 mm
W = 18.2 + 30 = 48.2
Area = 48.2² x ( 0.5 + 3.14/ 8) -
(3.14 x 18.2 ²/4)
= 1807.66 sqcm = 0.1808 sqm.
Say 0.181 sqm
For 10 m length qty. of concrete
reqd. = 1.81 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.81 6050.65 10951.68 A
Cost of 10 metres 10951.68
Cost of metre 1095.17
Say 1095.15
19.2.3 200 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Area = W x W/2 + ½ x (3.14 x W² / 4)-
(3.14 x D² / 4)
= W² x (0.5 + 3.14 / 8) - (3.14 x D² / 4)
Where W = D + X
D = 200 + 17 + 17 = 234 mm or 23.4 cm
X = 300 mm as trench depth is less
than 1200 mm
W = 23.4 + 30 = 53.4
Area = 53.4² x ( 0.5 + 3.14 / 8) -
(3.14 x 23.4²/4)
SUB HEAD : 19- DRAINAGE 1809
Code Description Unit Quantity Rate Amount
= 2115 sqcm = 0.2115 sqm
Say 0.211 sqm
For 10 m length qty. of concrete reqd.
= 2.11 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 2.11 6050.65 12766.87 A
Cost of 10 metres 12766.87
Cost of metre 1276.69
Say 1276.70
19.2.4 250 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
Area = W x W/2 + ½ x (3.14 x W² / 4)-
(3.14 x D² / 4)
= W² x (0.5 + 3.14 / 8) - (3.14 x D² / 4)
Where W = D + X
D = 250 + 20 + 20 = 290 mm or 29.0 cm
X = 300 mm as trench depth is less
than 1200 mm
W = 29 + 30 = 59
Area= 59² x ( 0.5 + 3.14/ 8) -
(3.14 x 29²/4)
= 2447 sqcm = 0.2447 sqm.
Say 0.244 sqm
For 10 m length qty. of concrete reqd.
= 2.44 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 2.44 6050.65 14763.59 A
Cost of 10 metres 14763.59
Cost of metre 1476.36
Say 1476.35
19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10
graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes
including bed concrete as per standard design :
19.3.1 100 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Detail of cost for 10 metres
Area = WxD1 + 2x½xR Cot QxR -
[R²/2(3.14/2-Q)] - (3.14/2)R²
= WD1 + R²(Cot Q) - R²(3.14/2 - Q)
-(3.14/2)R²
= WD1+R²(cot Q-3.14 + Q)
Where Sin Q = [R/(W/2)] = 2R/W
W = D + X ; X = 300 mm, D = 100 +
12 + 12 = 124 mm
W = 124 + 300 = 424 mm
SUB HEAD : 19- DRAINAGE 1810
Code Description Unit Quantity Rate Amount
D1 = Depth = 100 + (½ x 124) = 162 mm
R = 62 mm
Sin Q = (2x62)/424 = 0.292 therefor
Q = 17°0'
Hence Tan Q = 0.3057
Area = 424 x 162 + (62)² (Cot Q -
3.14 + Q)
= [68688 + 3844 (1/0.3057 - 180° +
17°0')] sqmm
= [68688 + 3844 (3.27 - 163°0' x
3.14/180)] sqmm
= (68688 + 3844 x 0.43) sqmm
= (68688 + 1652.92) sqmm
= 70340.92 sqmm
Say 70341 sqmm or 0.070341 sqm
For 10 m length qty. of concrete reqd.
= 0.07034x10 = 0.7034 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 0.7034 6050.65 4256.03 A
Cost of 10 metres 4256.03
Cost per metre 425.60
Say 425.60
19.3.2 150 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre length pipe
Area = WxD1 + 2x½xR Cot QxR -
[R²/2(3.14/2-Q)] - (3.14/2)R²
= WD1 + R²(Cot Q) - R²(3.14/2 - Q)
- (3.14/2)R²
= WD1 + R²(Cot Q - 3.14 + Q)
Where Sin Q = [R/(W/2)] = 2R/W
W = D + X ; X = 300 mm, D = 150
+ 16+ 16 = 182 mm
W = 182 + 300 = 482 mm
D1 = Depth = 150 + (½ x 182)
= 241 mm
R = 91 mm
Sin Q = (2x91)/482 = 0.3776 therefor
Q = 22°12'
Hence Tan Q = 0.4081
Area = 482 x 241 + (91)² (Cot Q - 3.14
+ Q)
= [116162 + 8281 (1/0.4081 - 180°
+ 22°12')] sqmm
= [116162 + 8281 (2.45 - 157°48' x
3.14/180)] sqmm
= [116162 + 8281 x (2.45-2.75)] sqmm
= [116162 + 8281 x (-0.30)] sqmm
= (116162 - 2484.3) sqmm
= 113677.7 sqmm
Say 113677.7 sqmm or 0.1136777 sqm
SUB HEAD : 19- DRAINAGE 1811
Code Description Unit Quantity Rate Amount
For 10 m length qty. of concrete reqd.
= 0.1136777x10 = 1.136777 cum.
Say 1.14 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.14 6050.65 6897.74 A
Cost of 10 metres 6897.74
Cost per metre 689.77
Say 689.75
19.3.3 200 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre length pipe
Area = WxD1 + 2x½xR Cot QxR
- [R²/2(3.14/2-Q)] - (3.14/2)R²
= WD1 + R²(Cot Q) - R²(3.14/2 - Q)
- (3.14/2)R2
= WD1 + R²(Cot Q - 3.14 + Q)
Where Sin Q = [R/(W/2)] = 2R/W
W = D + X ; X = 300 mm, D = 200+
17 + 17 = 234 mm
W = 234 + 300 = 534 mm
D1 = Depth = 150 + (½ x 234) = 267 mm
R = 117 mm
Sin Q = (2x117)/534 = 0.4382 therefor
Q= 26°0'
Hence Tan Q = 0.4877
Area = 534 x 267 + (117)² (Cot Q
- 3.14 + Q)
= [142578 + 13689 (1/0.4877 - 180°
+ 26°0')] sqmm
= [142578 + 13689 (2.05 - 154°0' x
3.14/180)] sqmm
= [142578 + 13689 x (2.05-2.69)] sqmm
= [142578 + 13689 x (-0.64)] sqmm
= (142578 - 8760.96) sqmm
= 133817.04 sqmm
Say 133817 sqmm or 0.134 sqm
For 10 m length qty. of concrete reqd.
= 0.134x10 = 1.34 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.34 6050.65 8107.87 A
Cost of 10 metres 8107.87
Cost per metre 810.79
Say 810.80
SUB HEAD : 19- DRAINAGE 1812
19.3.4 250 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre length pipe
Area = WxD1 + 2x½xR Cot QxR
- [R²/2(3.14/2-Q)] - (3.14/2)R²
= WD1 + R²(Cot Q) - R²(3.14/2 - Q)
- (3.14/2)R2
= WD1 + R²(Cot Q - 3.14 + Q)
Where Sin Q = [R/(W/2)] = 2R/W
W = D + X ; X = 300 mm, D = 250
+ 20 + 20 = 290 mm
W = 290 + 300 = 590 mm
D1 = Depth = 150 + (½ x 290) = 295 mm
R = 145 mm
Sin Q = (2x145)/590 = 0.49154
therefor Q = 29°26'
Hence Tan Q = 0.5635
Area = 590 x 295 + (145)²
(Cot Q - 3.14 + Q)
= [174050 + 21025 (1/0.5635 - 180°
+ 29°26')] sqmm
= [174050 + 21025 (1.77 - 150°34' x
3.14/180)] sqmm
= [174050 + 21025 x (1.77-2.63)] sqmm
= [174050 + 21025 x (-0.86)] sqmm
= (174050 - 18081.5) sqmm
= 155968.5 sqmm
Say 155968 sqmm or 0.156 sqm
For 10 m length qty. of concrete reqd.
= 0.156x10 = 1.56 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.56 6050.65 9439.01 A
Cost of 10 metres 9439.01
Cost per metre 943.90
Say 943.90
19.3.5 300 mm diameter S.W. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre length pipe
Area = WxD1 + 2x½xR Cot QxR -
[R²/2(3.14/2-Q)] - (3.14/2)R²
= WD1 + R²(Cot Q) - R²(3.14/2 - Q)-
(3.14/2)R2
= WD1 + R²(Cot Q - 3.14 + Q)
Where Sin Q = [R/(W/2)] = 2R/W
W = D + X ; X = 300 mm, D = 300
+ 25 + 25 = 350 mm
W = 350 + 300 = 650 mm
D1 = Depth = 150 + (½ x 350) = 325 mm
R = 175 mm
Sin Q = (2x175)/650 = 0.5385 therefor
Q = 32°34'
SUB HEAD : 19- DRAINAGE 1813
Code Description Unit Quantity Rate Amount
Hence Tan Q = 0.6387
Area = 650 x 325 + (175)²
(Cot Q - 3.14 + Q)
= [211250 + 30625 (1/0.6387 - 180°+
32°34')] sqmm
= [211250 + 30625 (1.566 - 147°26' x
3.14/180)] sqmm
= [211250 + 30625 x (1.566-2.571)] sqmm
= [211250 + 30625 x (-1.005)] sqmm
= [211250 - 30778.13) sqmm
= 180471.87 sqmm
Say 0.180 sqm
For 10 m length qty. of concrete reqd.
= 0.180x10 = 1.80 cum
4.1.10 Rate as per item no 4.1.10 of
SH : Concrete Work cum 1.80 6050.65 10891.17 A
Cost of 10 metres 10891.17
Cost per metre 1089.12
Say 1089.10
19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with
C.I. grating brick masonry chamber with water tight C.I. cover with frame of
300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and
frame to be not less than 2.70 kg as per standard design:
19.4.1 100x100 mm size P type
19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost of one gully tarp
1900 S.W. gully trap P type 100x100 mm each 1.00 115.00 115.00
1364 C.I. grating 100x100 mm each 1.00 40.00 40.00
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total=0.107 cum
Deduct:
0.345÷3x[0.09+0.01+(0.09x0.01)1/2]
= 0.015 cum
3.14/4x(0.124)²x0.47 = 0.006 cum
Total= 0.021 cum
Net quantity 0.107 cum (-) 0.021 cum
= 0.086 cum say 0.09 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.09 5660.45 509.44 A
Brick work with 7.5 class designation
brick in cement mortar 1:4 (1 cement :
4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum.
say 0.13 cum
SUB HEAD : 19- DRAINAGE 1814
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.13 6882.00 894.66 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m = 0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.358x(1.20+0.40)] = 0.286 sqm.
say 0.29 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.29 386.55 112.10 A
TOTAL 2235.74 W
Add 1 % Water charges on "W-A" 6.45
TOTAL 2242.19 X
Add GST on "X-A" (multiplying
factor 0.1405) 91.46
TOTAL 2333.65 Y
Add 15% CPOH on "Y-A" 111.37
TOTAL 2445.02 Z
Add Cess @ 1% on "Z-A" 8.54
Cost of each 2453.56
Say 2453.55
19.4.1.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Detaila of cost of one gully tarp
1900 S.W. gully trap P type 100x100 mm each 1.00 115.00 115.00
1364 C.I. grating 100x100 mm each 1.00 40.00 40.00
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total=0.107 cum
Deduct:
0.345÷3x[0.09+0.01+(0.09x0.01)1/2]
= 0.015 cum
3.14/4x(0.124)²x0.47 = 0.006 cum
Total = 0.021 cum
Net quantity 0.107 cum (-) 0.021 cum
= 0.086 cum say 0.09 cum
SUB HEAD : 19- DRAINAGE 1815
Code Description Unit Quantity Rate Amount
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.09 5660.45 509.44 A
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) cement mortar 1:4
(1 cement :4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum
say 0.13 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.13 6528.70 848.73 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m = 0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.358x(1.20+0.40)] = 0.286 sqm
say 0.29 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.29 386.55 112.10 A
TOTAL 2189.81 W
Add 1 % Water charges on "W-A" 6.45
TOTAL 2196.26 X
Add GST on "X-A" (multiplying
factor 0.1405) 91.46
TOTAL 2287.72 Y
Add 15% CPOH on "Y-A" 111.37
TOTAL 2399.09 Z
Add Cess @ 1% on "Z-A" 8.54
Cost of each 2407.63
Say 2407.65
19.4.2 150 x 100 mm size P type
19.4.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost of one gully tarp
1902 S.W. gully trap P type 150x100 mm each 1.00 155.00 155.00
1366 C.I. grating 150x150 mm each 1.00 55.00 55.00
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total =0.107 cum
SUB HEAD : 19- DRAINAGE 1816
Code Description Unit Quantity Rate Amount
Deduct:
0.322÷3x[0.09+0.023+(0.09x0.023)1/2]
= 0.017 cum
3.14/4x(0.124)²x0.485 = 0.006 cum
Total = 0.023 cum
Net quantity 0.107 cum (-) 0.023 cum
= 0.084 cum say 0.08 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.08 5660.45 452.84 A
Brick work with 75 class designation
brick in cement mortar 1:4 (1 cement
:4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum
say 0.13 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.13 6882.00 894.66 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m = 0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.337x(1.20+0.60)] = 0.303 sqm.
say 0.30 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.30 386.55 115.97 A
TOTAL 2238.00 W
Add 1 % Water charges on "W-A" 7.00
TOTAL 2245.00 X
Add GST on "X-A" (multiplying
factor 0.1405) 99.27
TOTAL 2344.27 Y
Add 15% CPOH on "Y-A" 120.87
TOTAL 2465.14 Z
Add Cess @ 1% on "Z-A" 9.27
Cost of each 2474.40
Say 2474.40
19.4.2.2 With sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost of one gully tarp
1902 S.W. gully trap P type 150x100 mm each 1.00 155.00 155.00
1366 C.I. grating 150x150 mm each 1.00 55.00 55.00
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
SUB HEAD : 19- DRAINAGE 1817
Code Description Unit Quantity Rate Amount
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total =0.107 cum
Deduct:
0.322÷3x[0.09+0.023+(0.09x0.023)1/2]
= 0.017 cum
3.14/4x(0.124)²x0.485 = 0.006 cum
Total= 0.023 cum
Net quantity 0.107 cum (-) 0.023 cum
= 0.084 cum say 0.08 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.08 5660.45 452.84 A
Brick work with sewer bricks
conforming to IS:4885 in cement
mortar 1:4 (1 cement :4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum
say 0.13 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.13 6528.70 848.73 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m = 0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.337x(1.20+0.60)] = 0.303 sqm.
say 0.30 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.30 386.55 115.97 A
TOTAL 2192.07 W
Add 1 % Water charges on "W-A" 7.00
TOTAL 2199.07 X
Add GST on "X-A" (multiplying
factor 0.1405) 99.27
TOTAL 2298.34 Y
Add 15% CPOH on "Y-A" 120.87
TOTAL 2419.21 Z
Add Cess @ 1% on "Z-A" 9.27
Cost of each 2428.47
Say 2428.45
19.4.3 180x150 mm size P type
19.4.3.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost of one gully tarp
1904 S.W. gully trap P type 180x150 mm each 1.00 230.00 230.00
1367 C.I. grating 180x180 mm each 1.00 65.00 65.00
SUB HEAD : 19- DRAINAGE 1818
Code Description Unit Quantity Rate Amount
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total=0.107 cum
Deduct:
0.155÷3x[0.09+0.032+(0.09x0.032)1/2]
= 0.008 cum
3.14/4x(0.182)²x0.70 =0.018 cum
Total= 0.026 cum
Net quantity 0.107 cum (-) 0.026 cum
= 0.081 cum say 0.08 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.08 5660.45 452.84 A
Brick work with 7.5 class designation
brick in cement mortar 1:4 (1 cement :
4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum.
say 0.13 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.13 6882.00 894.66 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m =0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.166x(1.20+0.72)] = 0.159 sqm
say 0.16 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.16 386.55 61.85 A
TOTAL 2268.89 W
Add 1 % Water charges on "W-A" 7.85
TOTAL 2276.73 X
Add GST on "X-A" (multiplying
factor 0.1405) 111.33
TOTAL 2388.06 Y
Add 15% CPOH on "Y-A" 135.56
TOTAL 2523.62 Z
Add Cess @ 1% on "Z-A" 10.39
Cost of each 2534.01
Say 2534.00
SUB HEAD : 19- DRAINAGE 1819
19.4.3.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost of one gully tarp
1904 S.W. gully trap P type 180x150 mm each 1.00 230.00 230.00
1367 C.I. grating 180x180 mm each 1.00 65.00 65.00
1352 C.I. cover and frame 300x300 mm inside each 1.00 480.00 480.00
9977 Carriage of materials L.S. 4.50 2.12 9.54
Cement concrete 1:5:10 ( 1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.68x0.68x0.10 m = 0.046 cum
Concrete around trap
0.30x0.30x0.675 m = 0.061 cum
Total=0.107 cum
Deduct:
0.155÷3x[0.09+0.032+(0.09x0.032)1/2]
= 0.008 cum
3.14/4x(0.182)²x0.70 =0.018 cum
Total= 0.026 cum
Net quantity 0.107 cum (-) 0.026 cum
= 0.081 cum say 0.08 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.08 5660.45 452.84 A
Brick work with sewer bricks
conforming to IS:4885 in cement
mortar 1:4 (1 cement : 4 coarse sand)
1.66x0.115x0.675 m = 0.129 cum
say 0.13 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.13 6528.70 848.73 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
1.66x0.115x0.04 m =0.008 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.008 9375.20 75.00 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement :
[1/2x0.166x(1.20+0.72)] = 0.159 sqm
say0.16 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.16 386.55 61.85 A
TOTAL 2222.96 W
Add 1 % Water charges on "W-A" 7.85
TOTAL 2230.80 X
Add GST on "X-A" (multiplying
factor 0.1405) 111.33
TOTAL 2342.13 Y
Add 15% CPOH on "Y-A" 135.56
TOTAL 2477.69 Z
Add Cess @ 1% on "Z-A" 10.39
Cost of each 2488.08
Say 2488.10
SUB HEAD : 19- DRAINAGE 1820
19.5 Dismantling of old S.W. pipes including breaking of joints and bed concrete
stacking of useful materials near the site within 50 m lead and disposal of
unserviceable materials into municipal dumps :
19.5.1 100 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.36 645.00 232.20
TOTAL 548.25 W
Add 1 % Water charges on "W" 5.48
TOTAL 553.73 X
Add GST on "X" (multiplying
factor 0.1405) 77.80
TOTAL 631.53 Y
Add 15% CPOH on "Y" 94.73
TOTAL 726.26 Z
Add Cess @ 1% on "Z" 7.26
Cost of 10 metres 733.52
Cost of 1 metre 73.35
Say 73.35
19.5.2 150 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.45 645.00 290.25
TOTAL 606.30 W
Add 1 % Water charges on "W" 6.06
TOTAL 612.36 X
Add GST on "X" (multiplying
factor 0.1405) 86.04
TOTAL 698.40 Y
Add 15% CPOH on "Y" 104.76
TOTAL 803.16 Z
Add Cess @ 1% on "Z" 8.03
Cost of 10 metres 811.19
Cost of 1 metre 81.12
Say 81.10
19.5.3 200 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.49 645.00 316.05
SUB HEAD : 19- DRAINAGE 1821
Code Description Unit Quantity Rate Amount
0115 Coolie day 0.51 645.00 328.95
TOTAL 645.00 W
Add 1 % Water charges on "W" 6.45
TOTAL 651.45 X
Add GST on "X" (multiplying
factor 0.1405) 91.53
TOTAL 742.98 Y
Add 15% CPOH on "Y" 111.45
TOTAL 854.43 Z
Add Cess @ 1% on "Z" 8.54
Cost of 10 metres 862.97
Cost of 1 metre 86.30
Say 86.30
19.5.4 250 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.57 645.00 367.65
TOTAL 683.70 W
Add 1 % Water charges on "W" 6.84
TOTAL 690.54 X
Add GST on "X" (multiplying
factor 0.1405) 97.02
TOTAL 787.56 Y
Add 15% CPOH on "Y" 118.13
TOTAL 905.69 Z
Add Cess @ 1% on "Z" 9.06
Cost of 10 metres 914.75
Cost of 1 metre 91.47
Say 91.45
19.5.5 300 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.49 645.00 316.05
0115 Coolie day 0.63 645.00 406.35
TOTAL 722.40 W
Add 1 % Water charges on "W" 7.22
TOTAL 729.62 X
Add GST on "X" (multiplying
factor 0.1405) 102.51
TOTAL 832.14 Y
Add 15% CPOH on "Y" 124.82
TOTAL 956.96 Z
Add Cess @ 1% on "Z" 9.57
Cost of 10 metres 966.53
Cost of 1 metre 96.65
Say 96.65
SUB HEAD : 19- DRAINAGE 1822
19.5.6 350 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.60 645.00 387.00
0115 Coolie day 0.69 645.00 445.05
TOTAL 832.05 W
Add 1 % Water charges on "W" 8.32
TOTAL 840.37 X
Add GST on "X" (multiplying
factor 0.1405) 118.07
TOTAL 958.44 Y
Add 15% CPOH on "Y" 143.77
TOTAL 1102.21 Z
Add Cess @ 1% on "Z" 11.02
Cost of 10 metres 1113.23
Cost of 1 metre 111.32
Say 111.30
19.5.7 400 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.75 645.00 483.75
TOTAL 909.45 W
Add 1 % Water charges on "W" 9.09
TOTAL 918.54 X
Add GST on "X" (multiplying
factor 0.1405) 129.06
TOTAL 1047.60 Y
Add 15% CPOH on "Y" 157.14
TOTAL 1204.74 Z
Add Cess @ 1% on "Z" 12.05
Cost of 10 metres 1216.79
Cost of 1 metre 121.68
Say 121.70
19.5.8 450 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
LABOUR
0114 Beldar day 0.66 645.00 425.70
0115 Coolie day 0.81 645.00 522.45
TOTAL 948.15 W
Add 1 % Water charges on "W" 9.48
TOTAL 957.63 X
SUB HEAD : 19- DRAINAGE 1823
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 134.55
TOTAL 1092.18 Y
Add 15% CPOH on "Y" 163.83
TOTAL 1256.01 Z
Add Cess @ 1% on "Z" 12.56
Cost of 10 metres 1268.57
Cost of 1 metre 126.86
Say 126.85
19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with
collars jointed with stiff mixture of cement mortar in the proportion of 1:2
(1 cement : 2 fine sand) including testing of joints etc. complete :
19.6.1 100 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1700 R.C.C. pipes NP2 class 100 mm dia metre 10.00 210.00 2100.00
(in 2 m. length = 5 Nos.)
1714 R.C.C. collars NP2 class 100 mm dia each 5.00 35.00 175.00
5 Nos.
2275 Carriage of R.C.C. pipes 100 mm dia 100 metre 0.10 358.32 35.83
Cement of 5 joints = 5x0.00065
= 0.00325 cum = 0.0048 t
say 0.005 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.005 5000.00 25.00
2209 Carriage of Cement tonne 0.005 145.72 0.73
Fine sand for 5 joint = 0.0013x5
= 0.0065 cum = 0.006 cum
0983 Fine sand (zone IV) cum 0.006 900.00 5.40
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.006 163.93 0.98
LABOUR
0123 Mason (brick layer) 1st class day 0.32 784.00 250.88
0124 Mason (brick layer) 2nd class day 0.32 714.00 228.48
0114 Beldar day 0.63 645.00 406.35
0101 Bhisti day 0.16 714.00 114.24
TOTAL 3342.89 W
Add 1 % Water charges on "W" 33.43
TOTAL 3376.32 X
Add GST on "X" (multiplying
factor 0.1405) 474.37
TOTAL 3850.70 Y
Add 15% CPOH on "Y" 577.60
TOTAL 4428.30 Z
Add Cess @ 1% on "Z" 44.28
Cost of 10 metres 4472.58
Cost of 1 metre 447.26
Say 447.25
SUB HEAD : 19- DRAINAGE 1824
19.6.2 150 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1701 R.C.C. pipes NP2 class 150 mm dia metre 10.00 220.00 2200.00
(in 2 m. length = 5 Nos.)
1715 R.C.C. collars NP2 class 150 mm dia each 5.00 37.00 185.00
5 Nos.
2281 Carriage of R.C.C. pipes 150 mm dia 100 metre 0.10 597.20 59.72
Cement of 5 joints = 5x0.0008
= 0.004 cum = 0.006 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.006 5000.00 30.00
2209 Carriage of Cement tonne 0.006 145.72 0.87
Fine sand for 5 joint = 0.0016x5
= 0.008 cum
0983 Fine sand (zone IV) cum 0.008 900.00 7.20
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.008 163.93 1.31
LABOUR
0123 Mason (brick layer) 1st class day 0.39 784.00 305.76
0124 Mason (brick layer) 2nd class day 0.39 714.00 278.46
0114 Beldar day 0.78 645.00 503.10
0101 Bhisti day 0.16 714.00 114.24
TOTAL 3685.67 W
Add 1 % Water charges on "W" 36.86
TOTAL 3722.52 X
Add GST on "X" (multiplying
factor 0.1405) 523.01
TOTAL 4245.54 Y
Add 15% CPOH on "Y" 636.83
TOTAL 4882.37 Z
Add Cess @ 1% on "Z" 48.82
Cost of 10 metres 4931.19
Cost of 1 metre 493.12
Say 493.10
19.6.3 250 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1702 R.C.C. pipes NP2 class 250 mm dia metre 10.00 365.00 3650.00
(in 2 m. length = 5 Nos.)
1716 R.C.C. collars NP2 class 250 mm dia each 5.00 55.00 275.00
5 Nos.
2287 Carriage of R.C.C. pipes 250 mm dia 100 metre 0.10 1380.48 138.05
Cement of 5 joints = 5x0.0012
= 0.006 cum = 0.009tonne
0367 Portland Cement (OPC-43 grade) tonne 0.009 5000.00 45.00
2209 Carriage of Cement tonne 0.009 145.72 1.31
Fine sand for 5 joint = 0.0024x5
= 0.012 cum
0983 Fine sand (zone IV) cum 0.012 900.00 10.80
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.012 163.93 1.97
SUB HEAD : 19- DRAINAGE 1825
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 0.54 784.00 423.36
0124 Mason (brick layer) 2nd class day 0.54 714.00 385.56
0114 Beldar day 1.50 645.00 967.50
0101 Bhisti day 0.23 714.00 164.22
TOTAL 6062.77 W
Add 1 % Water charges on "W" 60.63
TOTAL 6123.39 X
Add GST on "X" (multiplying
factor 0.1405) 860.34
TOTAL 6983.73 Y
Add 15% CPOH on "Y" 1047.56
TOTAL 8031.29 Z
Add Cess @ 1% on "Z" 80.31
Cost of 10 metres 8111.60
Cost of 1 metre 811.16
Say 811.15
19.6.4 300 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1703 R.C.C. pipes NP2 class 300 mm dia metre 10.00 450.00 4500.00
(in 2.5 m. length = 4 Nos.)
1717 R.C.C. collars NP2 class 300 mm dia each 4.00 56.00 224.00
4 Nos.
2290 Carriage of R.C.C. pipes 300 mm dia 100 metre 0.10 1706.30 170.63
Cement of 4 joints = 4x0.00185
= 0.0074 cum = 0.011 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.011 5000.00 55.00
2209 Carriage of Cement tonne 0.011 145.72 1.60
Fine sand for 4 joint = 0.0037x4
= 0.0148 say 0.015cum
0983 Fine sand (zone IV) cum 0.015 900.00 13.50
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.015 163.93 2.46
LABOUR
0123 Mason (brick layer) 1st class day 0.59 784.00 462.56
0124 Mason (brick layer) 2nd class day 0.59 714.00 421.26
0114 Beldar day 1.16 645.00 748.20
0101 Bhisti day 0.20 714.00 142.80
TOTAL 6742.01 W
Add 1 % Water charges on "W" 67.42
TOTAL 6809.43 X
Add GST on "X" (multiplying
factor 0.1405) 956.73
TOTAL 7766.16 Y
Add 15% CPOH on "Y" 1164.92
TOTAL 8931.08 Z
Add Cess @ 1% on "Z" 89.31
Cost of 10 metres 9020.39
Cost of 1 metre 902.04
Say 902.05
SUB HEAD : 19- DRAINAGE 1826
19.6.5 450 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1704 R.C.C. pipes NP2 class 450 mm dia metre 10.00 775.00 7750.00
(in 2.5 m. length = 4 Nos.)
1718 R.C.C. collars NP2 class 450 mm dia each 4.00 110.00 440.00
4 Nos.
2299 Carriage of R.C.C. pipes 450 &
500 mm dia 100 metre 0.10 3981.36 398.14
Cement of 4 joints = 4x0.0041
= 0.0164 cum = 0.024 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.024 5000.00 120.00
2209 Carriage of Cement tonne 0.024 145.72 3.50
Fine sand for 4 joint = 0.0082x4
= 0.033 cum
0983 Fine sand (zone IV) cum 0.033 900.00 29.70
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.033 163.93 5.41
LABOUR
0123 Mason (brick layer) 1st class day 0.75 784.00 588.00
0124 Mason (brick layer) 2nd class day 0.75 714.00 535.50
0114 Beldar day 1.50 645.00 967.50
0101 Bhisti day 0.33 714.00 235.62
TOTAL 11073.36 W
Add 1 % Water charges on "W" 110.73
TOTAL 11184.10 X
Add GST on "X" (multiplying
factor 0.1405) 1571.37
TOTAL 12755.46 Y
Add 15% CPOH on "Y" 1913.32
TOTAL 14668.78 Z
Add Cess @ 1% on "Z" 146.69
Cost of 10 metres 14815.47
Cost of 1 metre 1481.55
Say 1481.55
19.6.6 500 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1705 R.C.C. pipes NP2 class 500 mm dia metre 10.00 950.00 9500.00
(in 2.5 m. length = 4 Nos.)
1719 R.C.C. collars NP2 class 500 mm dia each 4.00 120.00 480.00
4 Nos.
2299 Carriage of R.C.C. pipes 450 &
500 mm dia 100 metre 0.10 3981.36 398.14
Cement of 4 joints = 4x0.0045
= 0.018 cum = 0.026 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.026 5000.00 130.00
SUB HEAD : 19- DRAINAGE 1827
Code Description Unit Quantity Rate Amount
2209 Carriage of Cement tonne 0.026 145.72 3.79
Fine sand for 4 joints = 0.0089x4
= 0.0356 cum = 0.036 cum
0983 Fine sand (zone IV) cum 0.036 900.00 32.40
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.036 163.93 5.90
LABOUR
0123 Mason (brick layer) 1st class day 0.81 784.00 635.04
0124 Mason (brick layer) 2nd class day 0.81 714.00 578.34
0114 Beldar day 1.62 645.00 1044.90
0101 Bhisti day 0.33 714.00 235.62
TOTAL 13044.13 W
Add 1 % Water charges on "W" 130.44
TOTAL 13174.57 X
Add GST on "X" (multiplying
factor 0.1405) 1851.03
TOTAL 15025.59 Y
Add 15% CPOH on "Y" 2253.84
TOTAL 17279.43 Z
Add Cess @ 1% on "Z" 172.79
Cost of 10 metres 17452.23
Cost of 1 metre 1745.22
Say 1745.20
19.6.7 600 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1706 R.C.C. pipes NP2 class 600 mm dia
(in 2.5 m. length = 4 Nos.) metre 10.00 1150.00 11500.00
1720 R.C.C. collars NP2 class 600 mm dia
4 Nos. each 4.00 145.00 580.00
2303 Carriage of R.C.C. pipes 600, 700,
750 & 800 mm dia 100 metre 0.10 5972.04 597.20
Cement of 4 joints = 4x0.0054
= 0.0216 cum = 0.032 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.032 5000.00 160.00
2209 Carriage of Cement tonne 0.032 145.72 4.66
Fine sand for 4 joints = 0.0108x4
= 0.043 cum
0983 Fine sand (zone IV) cum 0.043 900.00 38.70
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.043 163.93 7.05
LABOUR
0123 Mason (brick layer) 1st class day 0.92 784.00 721.28
0124 Mason (brick layer) 2nd class day 0.92 714.00 656.88
0114 Beldar day 1.83 645.00 1180.35
SUB HEAD : 19- DRAINAGE 1828
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.33 714.00 235.62
TOTAL 15681.75 W
Add 1 % Water charges on "W" 156.82
TOTAL 15838.56 X
Add GST on "X" (multiplying
factor 0.1405) 2225.32
TOTAL 18063.88 Y
Add 15% CPOH on "Y" 2709.58
TOTAL 20773.46 Z
Add Cess @ 1% on "Z" 207.73
Cost of 10 metres 20981.20
Cost of 1 metre 2098.12
Say 2098.10
19.6.8 700 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1707 R.C.C. pipes NP2 class 700 mm dia metre 10.00 1500.00 15000.00
(in 2.5 m. length = 4 Nos.)
1721 R.C.C. collars NP2 class 700 mm dia each 4.00 160.00 640.00
4 Nos.
2303 Carriage of R.C.C. pipes 600, 700,
750 & 800 mm dia 100 metre 0.10 5972.04 597.20
Cement of 4 joints = 4x0.0062
= 0.0248 cum = 0.037 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.037 5000.00 185.00
2209 Carriage of Cement tonne 0.037 145.72 5.39
Fine sand for 4 joints = 0.0124x4
= 0.0496 cum = 0.05 cum
0983 Fine sand (zone IV) cum 0.05 900.00 45.00
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.05 163.93 8.20
LABOUR
0123 Mason (brick layer) 1st class day 1.03 784.00 807.52
0124 Mason (brick layer) 2nd class day 1.03 714.00 735.42
0114 Beldar day 2.06 645.00 1328.70
0101 Bhisti day 0.42 714.00 299.88
TOTAL 19652.31 W
Add 1 % Water charges on "W" 196.52
TOTAL 19848.84 X
Add GST on "X" (multiplying
factor 0.1405) 2788.76
TOTAL 22637.60 Y
Add 15% CPOH on "Y" 3395.64
TOTAL 26033.24 Z
Add Cess @ 1% on "Z" 260.33
Cost of 10 metres 26293.57
Cost of 1 metre 2629.36
Say 2629.35
SUB HEAD : 19- DRAINAGE 1829
19.6.9 800 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1709 R.C.C. pipes NP2 class 800 mm dia metre 10.00 1825.00 18250.00
(in 2.5 m. length = 4 Nos.)
1723 R.C.C. collars NP2 class 800 mm dia each 4.00 225.00 900.00
4 Nos.
2303 Carriage of R.C.C. pipes 600, 700,
750 & 800 mm dia 100 metre 0.10 5972.04 597.20
Cement of 4 joints = 4x0.0072
= 0.0288 cum = 0.042 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.042 5000.00 210.00
2209 Carriage of Cement tonne 0.042 145.72 6.12
Fine sand for 4 joints = 0.0143x4
= 0.0572 cum = 0.057 cum
0983 Fine sand (zone IV) cum 0.057 900.00 51.30
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.057 163.93 9.34
LABOUR
0123 Mason (brick layer) 1st class day 1.14 784.00 893.76
0124 Mason (brick layer) 2nd class day 1.14 714.00 813.96
0114 Beldar day 2.28 645.00 1470.60
0101 Bhisti day 0.42 714.00 299.88
TOTAL 23502.17 W
Add 1 % Water charges on "W" 235.02
TOTAL 23737.19 X
Add GST on "X" (multiplying
factor 0.1405) 3335.08
TOTAL 27072.27 Y
Add 15% CPOH on "Y" 4060.84
TOTAL 31133.10 Z
Add Cess @ 1% on "Z" 311.33
Cost of 10 metres 31444.44
Cost of1 metre 3144.44
Say 3144.45
19.6.10 900 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1710 R.C.C. pipes NP2 class 900 mm dia metre 10.00 2550.00 25500.00
(in 2.5 m. length = 4 Nos.)
1724 R.C.C. collars NP2 class 900 mm dia each 4.00 240.00 960.00
4 Nos.
2331 Carriage of R.C.C. pipes 900 mm dia 100 metre 0.10 8958.06 895.81
Cement of 4 joints = 4x0.0082
= 0.0328 cum = 0.0488 t Say 0.049
0367 Portland Cement (OPC-43 grade) tonne 0.049 5000.00 245.00
2209 Carriage of Cement tonne 0.049 145.72 7.14
Fine sand for 4 joints = 0.0164x4
= 0.066 cum
0983 Fine sand (zone IV) cum 0.066 900.00 59.40
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.066 163.93 10.82
SUB HEAD : 19- DRAINAGE 1830
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 1.25 784.00 980.00
0124 Mason (brick layer) 2nd class day 1.25 714.00 892.50
0114 Beldar day 3.00 645.00 1935.00
0101 Bhisti day 0.50 714.00 357.00
TOTAL 31842.67 W
Add 1 % Water charges on "W" 318.43
TOTAL 32161.09 X
Add GST on "X" (multiplying
factor 0.1405) 4518.63
TOTAL 36679.73 Y
Add 15% CPOH on "Y" 5501.96
TOTAL 42181.68 Z
Add Cess @ 1% on "Z" 421.82
Cost of 10 metres 42603.50
Cost of 1 metre 4260.35
Say 4260.35
19.6.11 1000 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1711 R.C.C. pipes NP2 class 1000 mm dia metre 10.00 2950.00 29500.00
(in 2.5 m. length = 4 Nos.)
1725 R.C.C. collars NP2 class 1000 mm dia each 4.00 295.00 1180.00
4 Nos.
2332 Carriage of R.C.C. pipes 1000 mm dia 100 metre 0.10 11944.08 1194.41
Cement of 4 joints = 4x0.0092
= 0.0368 cum = 0.055 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.055 5000.00 275.00
2209 Carriage of Cement tonne 0.055 145.72 8.01
Fine sand for 4 joints = 0.0185x4
= 0.074 cum
0983 Fine sand (zone IV) cum 0.074 900.00 66.60
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.074 163.93 12.13
LABOUR
0123 Mason (brick layer) 1st class day 1.36 784.00 1066.24
0124 Mason (brick layer) 2nd class day 1.36 714.00 971.04
0114 Beldar day 4.33 645.00 2792.85
0101 Bhisti day 0.50 714.00 357.00
TOTAL 37423.28 W
Add 1 % Water charges on "W" 374.23
TOTAL 37797.52 X
Add GST on "X" (multiplying
factor 0.1405) 5310.55
TOTAL 43108.07 Y
Add 15% CPOH on "Y" 6466.21
TOTAL 49574.28 Z
Add Cess @ 1% on "Z" 495.74
Cost of 10 metres 50070.02
Cost of 1 metre 5007.00
Say 5007.00
SUB HEAD : 19- DRAINAGE 1831
19.6.12 1100 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1712 R.C.C. pipes NP2 class 1100 mm dia metre 10.00 3250.00 32500.00
(in 2.5 m. length = 4 Nos.)
1726 R.C.C. collars NP2 class 1100 mm dia each 4.00 315.00 1260.00
4 Nos.
2333 Carriage of R.C.C. pipes 1100 mm dia 100 metre 0.10 11944.08 1194.41
Cement of 4 joints = 4x0.0103
=0.0412 cum = 0.061 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.061 5000.00 305.00
2209 Carriage of Cement tonne 0.061 145.72 8.89
Fine sand for 4 joints = 0.0206x4
= 0.0824 cum = 0.082 cum
0983 Fine sand (zone IV) cum 0.082 900.00 73.80
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.082 163.93 13.44
LABOUR
0123 Mason (brick layer) 1st class day 1.47 784.00 1152.48
0124 Mason (brick layer) 2nd class day 1.47 714.00 1049.58
0114 Beldar day 6.30 645.00 4063.50
0101 Bhisti day 0.60 714.00 428.40
TOTAL 42049.50 W
Add 1 % Water charges on "W" 420.49
TOTAL 42469.99 X
Add GST on "X" (multiplying
factor 0.1405) 5967.03
TOTAL 48437.03 Y
Add 15% CPOH on "Y" 7265.55
TOTAL 55702.58 Z
Add Cess @ 1% on "Z" 557.03
Cost of 10 metress 56259.61
Cost of 1 metre 5625.96
Say 5625.95
19.6.13 1200 mm dia. R.C.C. pipe
Code Description Unit Quantity Rate Amount
Details of cost for 10 metre
MATERIAL
1713 R.C.C. pipes NP2 class 1200 mm dia metre 10.00 3575.00 35750.00
(in 2.5 m. length = 4 Nos.)
1727 R.C.C. collars NP2 class 1200 mm dia each 4.00 375.00 1500.00
4 Nos.
2334 Carriage of R.C.C. pipes 1200 mm dia 100 metre 0.10 11944.08 1194.41
Cement of 4 joints = 4x0.0114
= 0.0456 cum = 0.068 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.068 5000.00 340.00
2209 Carriage of Cement tonne 0.068 145.72 9.91
Fine sand for 4 joints = 0.0229x4
= 0.0916 cum = 0.092 cum
0983 Fine sand (zone IV) cum 0.092 900.00 82.80
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.092 163.93 15.08
SUB HEAD : 19- DRAINAGE 1832
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 1.59 784.00 1246.56
0124 Mason (brick layer) 2nd class day 1.59 714.00 1135.26
0114 Beldar day 8.67 645.00 5592.15
0101 Bhisti day 0.67 714.00 478.38
TOTAL 47344.55 W
Add 1 % Water charges on "W" 473.45
TOTAL 47817.99 X
Add GST on "X" (multiplying
factor 0.1405) 6718.43
TOTAL 54536.42 Y
Add 15% CPOH on "Y" 8180.46
TOTAL 62716.89 Z
Add Cess @ 1% on "Z" 627.17
Cost of 10 metres 63344.05
Cost of 1 metre 6334.41
Say 6334.40
19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse
sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-
III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8
mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm
nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement
: 3 coarse sand) finished with floating coat of neat cement and making channels
in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) finished with a floating coat of neat cement complete as
per standard design :
19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light
duty) 455x610 mm internal dimensions, total weight of cover and frame to be
not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.51x1.41x0.20 m = 0.426 cum
Say 0.43 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.43 6326.05 2720.20 A
Brick work with bricks of class
designation 7.5 in foundation & plinth in
cement mortar 1:4 (1 cement : 4
coarse sand)
4.32x0.23x0.35 m = 0.348 cum
Less for pipe 2x3.14x(0.15m)²x0.23m
= (-) 0.008 cum
Total = 0.340 cum
SUB HEAD : 19- DRAINAGE 1833
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.34 6882.00 2339.88 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x0.90x(0.80/2) x (0.30+0.20)/2
= 0.18 cum
Less for pipe 1x0.90x3.14/4x(0.15m)²
= (-) 0.02 cum
= 0.16 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.16 7365.15 1178.42 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.40mx0.05m = 0.17 sqm
2x½x0.80x0.10m = 0.08 sqm
Total= 0.25 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.25 386.55 96.64 A
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.36x1.26x0.15m = 0.257 cum
Less for cover 0.61x0.455x0.15m
= (-) 0.042 cum
= 0.215 cum Say 0.22 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.22 10719.30 2358.25 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.41 645.00 -264.45
Mild steel reinforcement for slab :
0.22 cum @ 48.06 kg/cum = 10.57 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 10.57 88.95 940.20 A
Form work = 0.90x0.80 = 0.72 sqm
Less cover = 0.61x0.455m
= (-) 0.278 sqm
= 0.442 sqm Say 0.44 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.44 766.55 337.28 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
0124 Mason (brick layer) 2nd class day 0.06 714.00 42.84
1354 Rectangular cover 455x610 mm with
frame (low duty) each 1.00 1400.00 1400.00
(inside)
9977 Carriage of C.I. cover & frame L.S. 6.76 2.12 14.33
9999 Painting of C.I. cover & frame with
coal tar L.S. 6.76 2.12 14.33
SUB HEAD : 19- DRAINAGE 1834
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 11253.63 W
Add 1 % Water charges on "W-A" 12.83
TOTAL 11266.45 X
Add GST on "X-A" (multiplying
factor 0.1405) 182.03
TOTAL 11448.48 Y
Add 15% CPOH on "Y-A" 221.64
TOTAL 11670.13 Z
Add Cess @ 1% on "Z-A" 16.99
Cost of each 11687.12
Say 11687.10
19.7.1.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.51x1.41x0.20 m = 0.426 cum
Say 0.43 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.43 6326.05 2720.20 A
Brick work with sewer bricks
conforming to IS:4885 in cement
mortar 1:4 (1 cement :4 coarse sand)
4.32x0.23x0.35 m = 0.348 cum
Less for pipe 2x3.14x(0.15m)²x0.23m
= (-) 0.008 cum
Total= 0.340 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.34 6528.70 2219.76 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x0.90x(0.80/2) x (0.30+0.20)/2
= 0.18 cum
Less for pipe 1x0.90x3.14/4x(0.15m)²
= (-) 0.02 cum
Total= 0.16 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.16 7365.15 1178.42 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.40mx0.05m = 0.17 sqm
2x½x0.80x0.10m = 0.08 sqm
Total= 0.25 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.25 386.55 96.64 A
SUB HEAD : 19- DRAINAGE 1835
Code Description Unit Quantity Rate Amount
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.36x1.26x0.15m = 0.257 cum
Less for cover 0.61x0.455x0.15m
= (-) 0.042 cum
= 0.215 cum Say 0.22 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.22 10719.30 2358.25 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.41 645.00 -264.45
Mild steel reinforcement for slab :
0.22 cum @ 48.06 kg/cum = 10.57 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 10.57 88.95 940.20 A
Form work = 0.90x0.80 = 0.72 sqm
= 0.442 sqm Say 0.44 sqm
Less cover = 0.61x0.455m
= (-) 0.278 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.44 766.55 337.28 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
0124 Mason (brick layer) 2nd class day 0.06 714.00 42.84
1354 Rectangular cover 455x610 mm with
frame (low duty) each 1.00 1400.00 1400.00
(inside)
9977 Carriage of C.I. cover & frame L.S. 6.76 2.12 14.33
9999 Painting of C.I. cover & frame with
coal tar L.S. 6.76 2.12 14.33
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 11133.51 W
Add 1 % Water charges on "W-A" 12.83
TOTAL 11146.33 X
Add GST on "X-A" (multiplying
factor 0.1405) 182.03
TOTAL 11328.36 Y
Add 15% CPOH on "Y-A" 221.64
TOTAL 11550.00 Z
Add Cess @ 1% on "Z-A" 16.99
Cost of each 11567.00
Say 11567.00
19.7.2 Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium
duty) 500 mm internal diameter, total weight of cover and frame to be not less
than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :
19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
SUB HEAD : 19- DRAINAGE 1836
Code Description Unit Quantity Rate Amount
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.81x1.51x0.20 m = 0.547 cum
Say 0.55 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.55 6326.05 3479.33 A
Brick work with bricks of class
designation 7.5 in foundation & plinth in
cement mortar 1:4 (1 cement : 4
coarse sand)
5.12x0.23x0.80 m = 0.942 cum
Less for pipe 2x3.14x(0.15m)²x0.23m
=(-) 0.008 cum
Total= 0.934 cum Say 0.93 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.93 6882.00 6400.26 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x1.20x(0.90/2) x (0.30+0.20)/2
= 2.70 cum
Less for pipe 1.20x3.14/4x(0.15m)²
= (-) 0.021 cum
Total= 0.249 cum say 0.25
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.25 7365.15 1841.29 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20mx0.50m = 2.10 sqm
2x½x0.90x0.10m = 0.09 sqm
= 2.19 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.19 386.55 846.54 A
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.66x1.36x0.15m = 0.339 cum
Less for cover 0.7854x(0.50)²x0.15m
= (-) 0.029 cum
= 0.31 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.31 10719.30 3322.98 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.58 645.00 -374.10
Mild steel reinforcement for slab :
0.31 cum @ 80.09 kg/cum = 24.83 kg kg 24.83 88.95 2208.63 A
SUB HEAD : 19- DRAINAGE 1837
Code Description Unit Quantity Rate Amount
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work
Form work = 1.20x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.50)²
= (-) 0.196 sqm
= 0.884 sqm Say 0.88 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.88 766.55 674.56 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
1356 500 mm dia cover with frame
(medium duty) each 1.00 4400.00 4400.00
9977 Carriage of C.I. cover & frame L.S. 6.76 2.12 14.33
9999 Painting of C.I. cover & frame with
coal tar L.S. 6.76 2.12 14.33
9999 Sundries L.S. 16.64 2.12 35.28
TOTAL 22983.27 W
Add 1 % Water charges on "W-A" 42.10
TOTAL 23025.37 X
Add GST on "X-A" (multiplying
factor 0.1405) 597.37
TOTAL 23622.75 Y
Add 15% CPOH on "Y-A" 727.37
TOTAL 24350.12 Z
Add Cess @ 1% on "Z-A" 55.77
Cost of each 24405.88
Say 24405.90
19.7.2.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.81x1.51x0.20 m = 0.547 cum
Say 0.55 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.55 6326.05 3479.33 A
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) in cement mortar
1:4 (1 cement : 4 coarse sand)
5.12x0.23x0.80 m = 0.942 cum
Less for pipe 2x3.14x(0.15m)²x0.23m
= (-) 0.008 cum
= 0.934 cum Say 0.93 cum
SUB HEAD : 19- DRAINAGE 1838
Code Description Unit Quantity Rate Amount
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.93 6528.70 6071.69 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x1.20x(0.90/2) x (0.30+0.20)/2
= 2.70 cum
Less for pipe 1.20x3.14/4x(0.15m)²
= (-) 0.021 cum
= 0.249 cum say 0.25
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.25 7365.15 1841.29 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20mx0.50m = 2.10 sqm
2x½x0.90x0.10m = 0.09sqm
= 2.19 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.19 386.55 846.54 A
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.66x1.36x0.15m = 0.339 cum
Less for cover 0.7854x(0.50)²x0.15m =
(-) 0.029 cum
= 0.31 cum cum 0.31 10719.30 3322.98 A
5.3 Rate as per item no 5.3 of
SH : RCC Work
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.58 645.00 -374.10
Mild steel reinforcement for slab :
0.31 cum @ 80.09 kg/cum = 24.83 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 24.83 88.95 2208.63 A
Form work = 1.20x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.50)²
= (-) 0.196 sqm
= 0.884 sqm Say 0.88 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.88 766.55 674.56 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
1356 500 mm dia cover with frame
(medium duty) each 1.00 4400.00 4400.00
9977 Carriage of C.I. cover & frame L.S. 6.76 2.12 14.33
9999 Painting of C.I. cover & frame with
coal tar L.S. 6.76 2.12 14.33
SUB HEAD : 19- DRAINAGE 1839
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 16.64 2.12 35.28
TOTAL 22654.71 W
Add 1 % Water charges on "W-A" 42.10
TOTAL 22696.80 X
Add GST on "X-A" (multiplying
factor 0.1405) 597.37
TOTAL 23294.18 Y
Add 15% CPOH on "Y-A" 727.37
TOTAL 24021.55 Z
Add Cess @ 1% on "Z-A" 55.77
Cost of each 24077.31
Say 24077.30
19.7.3 Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy
duty) 560 mm internal diameter, total weight of cover and frame to be not less
than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :
19.7.3.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.81x1.51x0.20 m = 0.547 cum
Say 0.55 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.55 6326.05 3479.33 A
Brick work with bricks of class
designation 7.5 in foundation & plinth in
cement mortar 1:4 (1 cement : 4
coarse sand)
5.12x0.23x0.65 m = 0.765 cum
1x0.56x0.23x0.15 m = 0.019 cum
1x0.79x0.23x0.15 = 0.027 cum
= 0.811 cum
Less for pipe 2x3.14x(0.15m)²x0.23m
= (-) 0.008 cum
= 0.803 cum Say 0.80 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.80 6882.00 5505.60 A
Cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x1.20x(0.90/2)x(0.30+0.20)/2
= 0.27 cum
Less for pipe 1.20x3.14/4x(0.15m)²
= (-) 0.021 cum
= 0.249 cum say 0.25
SUB HEAD : 19- DRAINAGE 1840
Code Description Unit Quantity Rate Amount
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.25 7365.15 1841.29 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20mx0.35m = 1.47 sqm
2x0.56x0.15 m = 0.17 sqm
2x½x0.90x0.10m = 0.09 sqm
For fixing cover
0.96x0.96 m =0.922 sqm
= 2.652 sqm
Less cover 3.14/4x(0.56)² = (-) 0.246 sqm
= 2.406 sqm Say 2.41 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.41 386.55 931.59 A
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.66x1.36x0.15m = 0.339 cum
Add extra concreting 1x(0.56+0.79)x
0.15x0.15 m = 0.03 cum
Total= 0.369 cum
Less for cover 0.7854x(0.56)²x0.15m
= (-) 0.037 cum
= 0.332 cum Say 0.33 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.33 10719.30 3537.37 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.62 645.00 -399.90
Steel reinforcement for slab @
80.09 Kg/cum
For 0.33 cum = 26.43 kg.
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 26.43 88.95 2350.95 A
Form work inside area of man-hole
1.20x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.56)²
= (-) 0.246 sqm
= 0.834 sqm Say 0.83 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.83 766.55 636.24 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
3860 560 mm dia cover with frame
(Heavy duty) each 1.00 9100.00 9100.00
9977 Carriage of C.I. cover & frame L.S. 13.52 2.12 28.66
9999 Painting of C.I. cover & frame with
coal tar L.S. 6.76 2.12 14.33
SUB HEAD : 19- DRAINAGE 1841
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 27188.28 W
Add 1 % Water charges on "W-A" 89.06
TOTAL 27277.34 X
Add GST on "X-A" (multiplying
factor 0.1405) 1263.80
TOTAL 28541.14 Y
Add 15% CPOH on "Y-A" 1538.82
TOTAL 30079.95 Z
Add Cess @ 1% on "Z-A" 117.98
Cost of each 30197.93
Say 30197.95
19.7.3.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:4:8 (1 cement :
4 coarse sand : 8 graded stone
aggregate 40 mm nominal size)
1.81x1.51x0.20 m = 0.547 cum
Say 0.55 cum
4.1.8 Rate as per item no 4.1.8 of
SH : Concrete Work cum 0.55 6326.05 3479.33 A
sewer bricks conforming to IS:4885 in
cement mortar 1:4 (1 cement :
4 coarse sand)
5.12x0.23x0.65 m = 0.765 cum
1x0.56x0.23x0.15 m = 0.019 cum
1x0.79x0.23x0.15 = 0.027 cum
Total= 0.811 cum
Less for pipe 2x3.14x(0.15m)²x
0.23m = (-) 0.008 cum
= 0.803 cum Say 0.80 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.80 6528.70 5222.96 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) for
benching
2x1.20x(0.90/2)x(0.30+0.20)/2
= 0.27 cum
Less for pipe 1.20x3.14/4x(0.15m)²
= (-) 0.021 cum
= 0.249 cum say 0.25
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.25 7365.15 1841.29 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20mx0.35m = 1.47 sqm
2x0.56x0.15 m = 0.17 sqm
2x½x0.90x0.10m = 0.09 sqm
SUB HEAD : 19- DRAINAGE 1842
Code Description Unit Quantity Rate Amount
For fixing cover
0.96x0.96 m =0.922 sqm
Total= 2.652 sqm
Less cover 3.14/4x(0.56)² = (-) 0.246 sqm
= 2.406 sqm Say 2.41 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.41 386.55 931.59 A
Reinforced cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size)
For slab : 1.66x1.36x0.15m = 0.339 cum
Add extra concreting 1x(0.56+0.79)x
0.15x0.15 m = 0.03 cum
= 0.369 cum
Less for cover 0.7854x(0.56)²x0.15m
= (-) 0.037 cum
= 0.332 cum Say 0.33 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.33 10719.30 3537.37 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.62 645.00 -399.90
Steel reinforcement for slab @
80.09 Kg/cum
For 0.33 cum = 26.43 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 26.43 88.95 2350.95 A
Form work inside area of man-hole
1.20x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.56)²
= (-) 0.246 sqm
= 0.834 sqm Say 0.83 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC Work sqm 0.83 766.55 636.24 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
3860 560 mm dia cover with frame
(Heavy duty) each 1.00 9100.00 9100.00
9977 Carriage of C.I. cover & frame L.S. 13.52 2.12 28.66
9999 Painting of C.I. cover & frame
with coal tar L.S. 6.76 2.12 14.33
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 26905.64 W
Add 1 % Water charges on "W-A" 89.06
TOTAL 26994.70 X
Add GST on "X-A" (multiplying
factor 0.1405) 1263.80
TOTAL 28258.50 Y
Add 15% CPOH on "Y-A" 1538.82
TOTAL 29797.31 Z
Add Cess @ 1% on "Z-A" 117.98
Cost of each 29915.29
Say 29915.30
SUB HEAD : 19- DRAINAGE 1843
19.8 Extra for depth for manholes :
19.8.1 Size 90x80 cm
19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement : 4 coarse sand )
4.32x0.23x1.0 m = 0.994 cum
Say 0.99 cum
6.1.1 Rate as per item no. 6.1.1 of
S.H : brick work cum 0.99 6882.00 6813.18 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.40x1 m = 3.40 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 3.40 386.55 1314.27 A
TOTAL 8127.45
Cost for one metre 8127.45
Say 8127.45
19.8.1.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Brick work with modular extruded brunt
fly ash clay sewer bricks conforming to
IS : 4885 in cement mortar 1:4
(1 cement : 4 coarse sand )
4.32x0.23x1.0 m = 0.994 cum
Say 0.99 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.99 6528.70 6463.41 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.40x1 m = 3.40 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 3.40 386.55 1314.27 A
TOTAL 7777.68
Cost for one metre 7777.68
Say 7777.70
SUB HEAD : 19- DRAINAGE 1844
19.8.2 Size 120x90 cm
19.8.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement 4: coarse sand )
5.12x0.23x1.0 m = 1.178 cum
Say 1.18 cum
6.1.1 Rate as per item no. 6.1.1 of
S.H : brick work cum 1.18 6882.00 8120.76 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20x1 m = 4.20 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 4.20 386.55 1623.51 A
TOTAL 9744.27
Cost for one metre 9744.27
Say 9744.25
19.8.2.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
Brick work with modular extruded brunt
fly ash clay sewer bricks conforming to
IS :4885 in cement mortar 1:4 (1
cement: 4 coarse sand )
5.12x0.23x1.0 m = 1.178 cum
Say 1.18 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 1.18 6528.70 7703.87 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
4.20x1 m = 4.20 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 4.20 386.55 1623.51 A
TOTAL 9327.38
Cost for one metre 9327.38
Say 9327.40
19.9 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom
and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside
cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)
finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1
cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and
making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand
: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat
of neat cement, all complete as per standard design :
SUB HEAD : 19- DRAINAGE 1845
19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade
designation) 560 mm internal diameter conforming to I.S. 12592, total weight
of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
including centering, shuttering all complete. (Excavation, foot rests and 12mm
thick cement plaster at the external surface shall be paid for separately) :
19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 40 mm nominal size)
1.67x1.67x0.225 m = 0.63 cum
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 0.63 6670.25 4202.26 A
Brick work with bricks of class
designation 75 in cement mortar
1:4 (1 cement : 4 coarse sand)
Curved on plan
3.14x1.14x0.074x0.23 = 0.061
3.14x(1.14+0.79)/2x0.711x0.23 = 0.496
Total= 0.557
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.230x0.10 m
= 0.018 cum
2x3.14/4x(0.15)²x0.230 = 0.008 cum
Total= 0.026 cum
Net quantity 0.557-0.026 = 0.531
Say 0.53
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.53 6882.00 3647.46 A
Brick work in arches with 7.5 class
designation brick in cement mortar
1:3 ( 1 cement : 3 fine sand )
2x½x3.14x0.25 m x0.230x0.10 m
= 0.018 cum Say 0.02 cum
6.9 Rate as per item no 6.9 of
SH : Brick Work cum 0.02 13378.10 267.56 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
For benching :
3.14/4x(0.91+0.82)²x0.20 = 0.118 cum
[(2x8.133)/360]x(4/3)x3.14x(0.45)³
=0.017 cum
Total = 0.135 cum
Less pipe : 0.91x3.14/4x(0.15)2²
= (-) 0.016 cum
= 0.119 cum Say 0.12 cum
SUB HEAD : 19- DRAINAGE 1846
Code Description Unit Quantity Rate Amount
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete Work cum 0.12 7365.15 883.82 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate : 20 mm nominal size)
For fixing cover : 3.14/4 x d² x thickness
3.14/4x(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m
= (-) 0.037 cum
Total = 0.086 cum Say 0.09 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(0.80+0.56)/2x0.49 = 1.05 sqm
3.14x0.56x0.075 = 0.13 sqm
Benching
3.14x(0.80)²/4-0.80x0.15+0.80x½x
3.14x0.15 = 0.57 sqm
Total= 1.75 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.75 386.55 676.46 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
0124 Mason (brick layer) 2nd class day 0.06 714.00 42.84
S.F.R.C cover
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
9999 Sundries L.S. 16.9 2.12 35.83
TOTAL 11541.64 W
Add 1 % Water charges on "W-A" 10.20
TOTAL 11551.85 X
Add GST on "X-A" (multiplying
factor 0.1405) 144.79
TOTAL 11696.63 Y
Add 15% CPOH on "Y-A" 176.30
TOTAL 11872.93 Z
Add Cess @ 1% on "Z-A" 13.52
Cost of one manhole 11886.45
Say 11886.45
19.9.1.2 With Sewer bricks conforming to IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate: 40 mm nominal size)
1.67x1.67x0.225 m = 0.63 cum
SUB HEAD : 19- DRAINAGE 1847
Code Description Unit Quantity Rate Amount
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 0.63 6670.25 4202.26 A
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) in cement mortar 1:4
(1 cement : 4 coarse sand)
Curved on plan
3.14x1.14x0.074x0.23 = 0.061
3.14x(1.14+0.79)/2x0.711x0.23 = 0.496
= 0.557
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.230x0.10 m
= 0.018 cum
2x3.14/4x(0.15)²x0.230 = 0.008 cum
Total= 0.026 cum
Net quantity 0.557-0.026 = 0.531
Say 0.53
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.53 6528.70 3460.21 A
Brick work in arches with modular
extruded brunt fly ash clay sewer
bricks conforming to IS : 4885 in
cement mortar 1:3 ( 1 cement : 3 fine
sand )
2x½x3.14x0.25 m x0.230x0.10 m
= 0.018 cum Say 0.02 cum
6.37 Rate as per item No 6.37 of
SH : Brick Work cum 0.02 11763.25 235.27 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
For benching :
3.14/4x(0.91+0.82)²x0.20 = 0.118 cum
[(2x8.133)/360]x(4/3)x3.14x(0.45)³
=0.017 cum
Total= 0.135 cum
Less pipe : 0.91x3.14/4x(0.15)²
= (-) 0.016 cum
Total= 0.119 cum Say 0.12 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete Work cum 0.12 7365.15 883.82 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
For fixing cover : 3.14/4 x d² x thickness
3.14/4x(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m
= (-) 0.037 cum
Total = 0.086 cum Say 0.09 cum
SUB HEAD : 19- DRAINAGE 1848
Code Description Unit Quantity Rate Amount
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(0.80+0.56)/2x0.49 = 1.05 sqm
3.14x0.56x0.075 = 0.13 sqm
Benching
3.14x(0.80)²/4-0.80x0.15+0.80x½x3.14x
0.15 = 0.57 sqm
Total= 1.75 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.75 386.55 676.46 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.06 784.00 47.04
0124 Mason (brick layer) 2nd class day 0.06 714.00 42.84
S.F.R.C cover
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
9999 Sundries L.S. 16.90 2.12 35.83
TOTAL 11322.10 W
Add 1 % Water charges on "W-A" 10.20
TOTAL 11332.30 X
Add GST on "X-A" (multiplying
factor 0.1405) 144.79
TOTAL 11477.09 Y
Add 15% CPOH on "Y-A" 176.30
TOTAL 11653.38 Z
Add Cess @ 1% on "Z-A" 13.52
Cost of one manhole 11666.90
Say 11666.90
19.10 Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond
0.91 m to 1.67 m
19.10.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Detail of cost of 0.76 m depth
Brick work in foundation with 7.5 class
designation bricks in cement mortar
1:4 (1 cement : 4 coarse sand)
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.63 6882.00 4335.66 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone 20mm
nominal size)
SUB HEAD : 19- DRAINAGE 1849
Code Description Unit Quantity Rate Amount
4.1.3 Rate as per item no 4.1.3 of
SH : Concrete Work cum 0.01 7365.15 73.65 A
12mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with
neat cement.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.33 386.55 900.66 A
Cost for 0.76 metre 5309.97
Cost for 1.00 metre 6986.81
Say 6986.80
19.10.2 With Sewer bricks conforming IS : 4885
Code Description Unit Quantity Rate Amount
Detail of cost of 0.76 m extra depth
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) in cement mortar
1:4 (1 cement : 4 coarse sand)
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.63 6528.70 4113.08 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
20mm nominal size)
4.1.3 Rate as per item no 4.1.3 of
SH : Concrete Work cum 0.01 7365.15 73.65 A
12mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.33 386.55 900.66 A
Cost for 0.76 metre 5087.39
Cost for 1.00 metre 6693.94
Say 6693.95
19.11 Constructing brick masonry circular manhole 1.22 m internal dia at bottom
and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside
cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)
finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement
: 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making
necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) finished with a floating coat of
neat cement, all complete as per standard design :
19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation)
560 mm internal diameter conforming to I.S. 12592, total weight of cover and
frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size) including
centering, shuttering all complete. (Excavation, foot rests and 12 mm thick
cement plaster at the external surface shall be paid for separately) :
SUB HEAD : 19- DRAINAGE 1850
19.11.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 40mm nominal size)
1.98x1.98x0.30 m = 1.178 cum
Say 1.18 cum
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 1.18 6670.25 7870.90 A
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement : 4 coarse sand)
Curved on plan
3.14x1.45x0.24x0.23 = 0.251
3.14x(1.45+0.79)/2x1.32x0.23 = 1.069
Total= 1.320
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.230x0.10 m
= 0.018 cum
2x3.14/4x(0.15)²x0.230 = 0.008 cum
Total = 0.026 cum
Net quantity 1.320-0.026 = 1.294
Say 1.29 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 1.29 6882.00 8877.78 A
Brick work in arches with 7.5 class
designation brick in cement mortar 1:3
( 1 cement : 3 coarse sand )
2x½x3.14x0.25 m x0.230x0.10 m
= 0.018 cum Say 0.02 cum
6.9 Rate as per item no 6.9 of
SH : Brick Work cum 0.02 13378.10 267.56 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
For benching :
3.14/4x(1.22)²x0.20 = 0.234 cum
[(2x8.133)/360]x(4/3)x3.14x(0.61)³
=0.043 cum
Total= 0.277 cum
Less pipe :1.22x3.14/4x(0.15)²(-)
= 0.0216 cum
Total= 0.2554 cum Say 0.26 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete Work cum 0.26 7365.15 1914.94 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
For fixing cover : 3.14/4 x d² x
thickness
3.14/4x(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x
0.15 m : (-) = 0.037 cum
Total= 0.086 cum Say 0.09 cum
SUB HEAD : 19- DRAINAGE 1851
Code Description Unit Quantity Rate Amount
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(1.136+0.56)/2x1.216 = 3.241 sqm
3.14x0.56x0.075 = 0.13 sqm
3.14x(1.136)²/4-1.136x1/2x3.14x0.15
= 1.112 sqm
Total= 4.483 sqm Say 4.48 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 4.48 386.55 1731.74 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
S.F.R.C manhole cover
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
9999 Sundries L.S. 16.9 2.12 35.83
TOTAL 22586.92 W
Add 1 % Water charges on "W-A" 10.80
TOTAL 22597.73 X
Add GST on "X-A" (multiplying
factor 0.1405) 153.29
TOTAL 22751.02 Y
Add 15% CPOH on "Y-A" 186.65
TOTAL 22937.67 Z
Add Cess @ 1% on "Z-A" 14.31
Cost of one manhole 22951.97
Say 22951.95
19.11.1.2 With Sewer bricks conforming IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate : 40 mm nominal size)
1.98x1.98x0.30 m = 1.178 cum
Say 1.18 cum
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 1.18 6670.25 7870.90 A
Brick work with modular extruded brunt
fly ash clay sewer bricks in cement
mortar 1:4 (1 cement : 4 coarse sand)
Curved on plan
3.14x1.45x0.24x0.23 = 0.251
3.14x(1.45+0.79)/2x1.32x0.23 = 1.069
Total = 1.320
SUB HEAD : 19- DRAINAGE 1852
Code Description Unit Quantity Rate Amount
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.230x0.10 m
= 0.018 cum
2x3.14/4x(0.15)²x0.230 = 0.008 cum
Total= 0.026 cum
Net quantity 1.320-0.026 = 1.294
Say 1.29 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 1.29 6528.70 8422.02 A
Brick work in arches with modular
extruded brunt fly ash clay sewer
bricks in cement mortar 1:3 ( 1 cement
: 3 fine sand )
2x½x3.14x0.25 m x0.230x0.10 m
= 0.018 cum Say 0.02 cum
6.37 Rate as per item No 6.37 of
SH : Brick Work cum 0.02 11763.25 235.27 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
For benching :
3.14/4x(1.22)²x0.20 = 0.234 cum
[(2x8.133)/360]x(4/3)x3.14x(0.61)³
=0.043 cum
Total= 0.277 cum
Less pipe :1.22x3.14/4x(0.15)²(-)
= 0.0216 cum
Total= 0.2554 cum Say 0.26 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete
Work cum 0.26 7365.15 1914.94 A
Cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone
aggregate 20
mm nominal size)
For fixing cover : 3.14/4 x d² x thickness
3.14/4(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m :
= (-) 0.037 cum
Total= 0.086 cum Say 0.09 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(1.136+0.56)/2x1.216 = 3.241 sqm
3.14x0.56x0.075 = 0.13 sqm
3.14x(1.136)²/4-1.136x1/2x3.14x0.15
= 1.112 sqm
Total= 4.483 sqm Say 4.48 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 4.48 386.55 1731.74 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
SUB HEAD : 19- DRAINAGE 1853
Code Description Unit Quantity Rate Amount
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
S.F.R.C manhole cover and frame
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
9999 Sundries L.S. 16.9 2.12 35.83
TOTAL 22098.87 W
Add 1 % Water charges on "W-A" 10.80
TOTAL 22109.67 X
Add GST on "X-A" (multiplying
factor 0.1405) 153.29
TOTAL 22262.96 Y
Add 15% CPOH on "Y-A" 186.65
TOTAL 22449.61 Z
Add Cess @ 1% on "Z-A" 14.31
Cost of one manhole 22463.92
Say 22463.90
19.12 Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond
1.68 m to 2.29 m :
19.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Detail of cost of 0.61 m extra depth
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement : 4 coarse sand)
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.66 6882.00 4542.12 A
12mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.56 386.55 989.57 A
Cost for 0.61 metre 5531.69
Cost for 1.00 metre 9068.34
Say 9068.35
19.12.2 With Sewer bricks conforming IS : 4885
Code Description Unit Quantity Rate Amount
Detail of cost of 0.61 m extra depth
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) in cement mortar
1:4 (1 cement : 4 coarse sand)
SUB HEAD : 19- DRAINAGE 1854
Code Description Unit Quantity Rate Amount
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 0.66 6528.70 4308.94 A
12mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement.
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.56 386.55 989.57 A
Cost for 0.61 metre 5298.51
Cost for 1.00 metre 8686.08
Say 8686.10
19.13 Constructing brick masonry circular manhole 1.52 m internal dia at bottom
and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside
cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)
finished with a floating coat of neat cement, foundation concrete 1:3:6 (1
cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and
making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand
: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat
of neat cement, all complete as per standard design :
19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation)
560 mm internal diameter conforming to I.S. 12592, total weight of cover and
frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size) including
centering, shuttering all complete. (Excavation, foot rests and 12 mm thick
cement plaster at the external surface shall be paid for separately) :
19.13.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 40 mm nominal size)
2.74x2.74x0.30 m = 2.25 cum
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 2.25 6670.25 15008.06 A
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement : 4 coarse sand)
Curved on plan
3.14x1.98x0.25x0.46 = 0.716 cum
3.14x(1.98+0.905)/2x0.345x1.93
= 3.019 cum
Total = 3.735 cum
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.46x0.10 m
= 0.036 cum
2x3.14/4x(0.15)²x0.460 = 0.016 cum
Total= 0.052 cum
Net quantity 3.735-0.052 = 3.683 cum
Say 3.68 cum
SUB HEAD : 19- DRAINAGE 1855
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 3.68 6882.00 25325.76 A
Brick work in arches with 7.5 class
designation brick in cement mortar 1:3
(1 cement : 3 coarse sand )
2x1/2x3.14x0.25 m x0.460x0.10 m
= 0.036 cum Say 0.04 cum
6.9 Rate as per item no 6.9 of
SH : Brick Work cum 0.04 13378.10 535.12 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
For benching :
3.14/4x(1.52)²x0.20 = 0.363 cum
[(2x8.133)/360]x(4/3)x3.14x(0.76)³
=0.083 cum
Total= 0.446 cum
Less pipe :1.52x3.14/4x(0.15)²(-)
= 0.027 cum
Total= 0.419 cum Say 0.42 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete cum 0.42 7365.15 3093.36 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
For fixing cover : 3.14/4 x d² x
thickness
3.14/4x(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x
0.15 m : = (-) 0.037 cum
Total= 0.086 cum Say 0.09 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(1.454+0.56)/2x1.799
= 5.694 sqm
3.14x0.56x0.075 = 0.13 sqm
Benching
3.14x(1.454)²/4-1.454x0.15+1.454x1/2x
3.14x0.15 =1.786 sqm
Total= 7.61 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 7.61 386.55 2941.65 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
S.F.R.C cover
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
SUB HEAD : 19- DRAINAGE 1856
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 16.90 2.12 35.83
TOTAL 48827.96 W
Add 1 % Water charges on "W-A" 10.80
TOTAL 48838.76 X
Add GST on "X-A" (multiplying
factor 0.1405) 153.29
TOTAL 48992.05 Y
Add 15% CPOH on "Y-A" 186.65
TOTAL 49178.70 Z
Add Cess @ 1% on "Z-A" 14.31
Cost of one manhole 49193.01
Say 49193.00
19.13.1.2 With Sewer bricks conforming IS : 4885
Code Description Unit Quantity Rate Amount
Details of cost for 1 manhole
MATERIAL
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate 40 mm nominal size)
2.74x2.74x0.30 m = 2.25 cum
4.1.6 Rate as per item no 4.1.6 of
SH : Concrete Work cum 2.25 6670.25 15008.06 A
Brick work with bricks modular
extruded brunt fly ash clay sewer
bricks in cement mortar 1:4 (1 cement
: 4 coarse sand)
Curved on plan
3.14x1.98x0.25x0.46 = 0.716 cum
3.14x(1.98+0.905)/2x0.345x1.93
= 3.019 cum
Total= 3.735 cum
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.46x0.10 m
= 0.036 cum
2x3.14/4x(0.15)²x0.460 = 0.016 cum
Total= 0.052 cum
Net quantity 3.735-0.052 = 3.683 cum
Say 3.68 cum
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 3.68 6528.70 24025.62 A
Brick work in arches with modular
extruded brunt fly ash clay sewer
bricks in cement mortar 1:3 ( 1 cement
: 3 fine sand )
2x1/2x3.14x0.25 m x0.460x0.10 m
= 0.036 cum Say 0.04 cum
6.37 Rate as per item No 6.37 of
SH : Brick Work cum 0.04 11763.25 470.53 A
Cement concrete 1:2:4(1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size )
SUB HEAD : 19- DRAINAGE 1857
Code Description Unit Quantity Rate Amount
For benching :
3.14/4x(1.52)²x0.20 = 0.363 cum
[(2x8.133)/360]x(4/3)x3.14x(0.76)³
=0.083 cum
Total= 0.446 cum
Less pipe :1.52x3.14/4x(0.15)²(-)
= 0.027 cum
= 0.419 cum Say 0.42 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete cum 0.42 7365.15 3093.36 A
Cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
For fixing cover : 3.14/4 x d² x thickness
3.14/4x(1.020)²x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m :
= (-) 0.037 cum
Net Quantity= 0.086 cum Say 0.09 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete cum 0.09 9375.20 843.77 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
3.14x(1.454+0.56)/2x1.799 = 5.694 sqm
3.14x0.56x0.075 = 0.13 sqm
Benching
3.14x(1.454)²/4-1.454x0.15+1.454x1/2x
3.14x0.15 =1.786 sqm
Total= 7.61 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 7.61 386.55 2941.65 A
LABOUR
Extra labour for making channel :
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
0124 Mason (brick layer) 2nd class day 0.10 714.00 71.40
S.F.R.C cover
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
9977 CARRIAGE L.S. 6.89 2.12 14.61
9999 Sundries L.S. 16.90 2.12 35.83
TOTAL 47463.22 W
Add 1 % Water charges on "W-A" 10.80
TOTAL 47474.02 X
Add GST on "X-A" (multiplying
factor 0.1405) 153.29
TOTAL 47627.31 Y
Add 15% CPOH on "Y-A" 186.65
TOTAL 47813.96 Z
Add Cess @ 1% on "Z-A" 14.31
Cost of one manhole 47828.27
Say 47828.25
SUB HEAD : 19- DRAINAGE 1858
19.14 Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond
2.30 m :
19.14.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Detail of cost of 1.88 m extra depth
Brick work with bricks of class
designation 7.5 in cement mortar
1:4 (1 cement: 4 coarse sand)
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 5.26 6882.00 36199.32 A
12 mm cement plaster 1:3 (1 cement:
3 coarse sand) finished with floating
coat of neat cement
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 8.99 386.55 3475.08 A
Cost for 1.88 metre 39674.40
Cost for 1.00 metre 21103.41
Say 21103.40
19.14.2 With Sewer bricks conforming IS : 4885
Code Description Unit Quantity Rate Amount
Detail of cost of 1.88 m extra depth
Brick work with modular extruded brunt
fly ash clay sewer bricks (Conforming
to IS: 4885 ) in cement mortar
1:4 (1 cement: 4 coarse sand)
6.36.1 Rate as per item No 6.36.1 of
SH : Brick Work cum 5.26 6528.70 34340.96 A
12 mm cement plaster 1:3 (1 cement:
3 coarse sand) finished with floating
coat of neat cement
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 8.99 386.55 3475.08 A
Cost for 1.88 metre 37816.05
Cost for 1.00 metre 20114.92
Say 20114.90
19.15 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement
concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size) as per standard design :
19.15.1 With 20x20 mm square bar
Code Description Unit Quantity Rate Amount
Details of cost for one M.S foot rests
MATERIAL
M.S. 20 mm square bar 0.75 m @
3.137 kg/m = 0.024
1006 Mild steel square bars quintal 0.024 4850.00 116.40
9988 Carriage, painting, and other sundries L.S. 1.82 2.12 3.86
LABOUR for fabrication
0103 Blacksmith 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.10 645.00 64.50
SUB HEAD : 19- DRAINAGE 1859
Code Description Unit Quantity Rate Amount
Cement concrete 1:3:6 (1 cement :
3 coarse sand : 6 graded stone
aggregate : 20 mm nominal size)
0.20x0.20x0.10 m = 0.004 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.004 8843.45 35.37 A
LABOUR for fixing M.S. foot rests
0123 Mason (brick layer) 1st class day 0.02 784.00 15.68
0124 Mason (brick layer) 2nd class day 0.02 714.00 14.28
0114 Beldar day 0.05 645.00 32.25
TOTAL 353.74 W
Add 1 % Water charges on "W-A" 3.18
TOTAL 356.93 X
Add GST on "X-A" (multiplying
factor 0.1405) 45.18
TOTAL 402.10 Y
Add 15% CPOH on "Y-A" 55.01
TOTAL 457.11 Z
Add Cess @ 1% on "Z-A" 4.22
Cost for 1 no. 461.33
Say 461.35
19.15.2 With 20 mm diameter round bar
Code Description Unit Quantity Rate Amount
Details of cost for one M.S foot rests
MATERIAL
M.S. round brass20 mm dia 0.75 m @
2.47kg/m = 0.018 q
1003 Mild steel round bar above 12 mm dia quintal 0.018 4750.00 85.50
9988 Carriage,painting, and other sundries L.S. 1.82 2.12 3.86
Labour for fabrication
0103 Blacksmith 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.10 645.00 64.50
Cement concrete 1:3:6 ( 1 cement :
3 coarse sand : 6 graded stone
aggregate : 20 mm nominal size)
0.20x0.20x0.10 m = 0.004 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.004 8843.45 35.37 A
LABOUR
0123 Mason (brick layer) 1st class day 0.02 784.00 15.68
0124 Mason (brick layer) 2nd class day 0.02 714.00 14.28
0114 Beldar day 0.05 645.00 32.25
TOTAL 322.84 W
Add 1 % Water charges on "W-A" 2.87
TOTAL 325.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 40.79
TOTAL 366.51 Y
Add 15% CPOH on "Y-A" 49.67
TOTAL 416.18 Z
Add Cess @ 1% on "Z-A" 3.81
Cost for 1 no. 419.99
Say 420.00
SUB HEAD : 19- DRAINAGE 1860
19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786,
having minimum cross section as 23 mmx25 mm and over all minimum length
263 mm and width as 165 mm with minimum 112 mm space between protruded
legs having 2 mm tread on top surface by ribbing or chequering besides
necessary and adequate anchoring projections on tail length on 138 mm as
per standard drawing and suitable to with stand the bend test and chemical
resistance test as per specifications and having manufacture's permanent
identification mark to be visible even after fixing, including fixing in manholes
with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :
6 graded stone aggregate 20 mm nominal size) complete as per design.
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7354 Plastic encapsuled M.S. foot rest
30x20x15 cm each 1.00 110.00 110.00
9988 Carriage and other sundries L.S. 1.82 2.12 3.86
Cement concrete 1:3:6 (1 Cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
( 0.30x0.20x0.15 = 0.009 cum)
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.009 8843.45 79.59 A
LABOUR
0123 Mason (brick layer) 1st class day 0.02 784.00 15.68
0124 Mason (brick layer) 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.05 645.00 32.25
TOTAL 384.18 W
Add 1 % Water charges on "W-A" 3.05
TOTAL 387.23 X
Add GST on "X-A" (multiplying
factor 0.1405) 43.22
TOTAL 430.45 Y
Add 15% CPOH on "Y-A" 52.63
TOTAL 483.08 Z
Add Cess @ 1% on "Z-A" 4.03
Cost for 1 no. 487.11
Say 487.10
19.17 Replacement of M.S. foot rests in manholes including dismantling concrete
blocks and fixing with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement :
3 coarse sand : 6 graded stone aggregate 20 mm nominal size):
19.17.1 With 20x20 mm square bar
Code Description Unit Quantity Rate Amount
Details of cost for one M.S foot rests
MATERIAL
M.S. 20 mm square bar 0.75 m @ 3.137
kg/m =0.024 q
1006 Mild steel square bars quintal 0.024 4850.00 116.40
9988 Carriage,painting, and other sundries L.S. 1.82 2.12 3.86
Labour for fabrication
SUB HEAD : 19- DRAINAGE 1861
Code Description Unit Quantity Rate Amount
0103 Blacksmith 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.10 645.00 64.50
Cement concrete 1:3:6 ( 1 cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
0.20x0.20x0.10 m = 0.004 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.004 8843.45 35.37 A
LABOUR
for dismantling old forts rest cutting
holes and fixing new M.S. foot rests
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0114 Beldar day 0.1 645.00 64.50
TOTAL 430.93 W
Add 1 % Water charges on "W-A" 3.96
TOTAL 434.89 X
Add GST on "X-A" (multiplying
factor 0.1405) 56.13
TOTAL 491.02 Y
Add 15% CPOH on "Y-A" 68.35
TOTAL 559.37 Z
Add Cess @ 1% on "Z-A" 5.24
Cost for 1 no. 564.61
Say 564.60
19.17.2 With 20 mm diameter round bar
Code Description Unit Quantity Rate Amount
Details of cost for one M.S foot rests
MATERIAL
M.S. roumd bars 20 mm dia 0.75 m @
2.47 kg/m =0.018 q
1003 Mild steel round bar above 12 mm dia quintal 0.018 4750.00 85.50
9988 Carriage,painting, and other sundries L.S. 1.82 2.12 3.86
Labour for fabrication
0103 Blacksmith 2nd class day 0.10 714.00 71.40
0114 Beldar day 0.10 645.00 64.50
Cement concrete 1:3:6 ( 1 cement :
3 coarse sand : 6 graded stone
aggregate 20 mm nominal size)
0.20x0.20x0.10 m = 0.004 cum
4.2.5 Rate as per item no 4.2.5 of
SH : Concrete work cum 0.004 8843.45 35.37 A
LABOUR
for dismantling old forts rest cutting
holes and fixing new M.S. foot rests
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
SUB HEAD : 19- DRAINAGE 1862
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.10 645.00 64.50
TOTAL 400.03 W
Add 1 % Water charges on "W-A" 3.65
TOTAL 403.68 X
Add GST on "X-A" (multiplying
factor 0.1405) 51.75
TOTAL 455.43 Y
Add 15% CPOH on "Y-A" 63.01
TOTAL 518.43 Z
Add Cess @ 1% on "Z-A" 4.83
Cost for 1 no. 523.26
Say 523.25
19.18 Supplying and fixing C.I. cover without frame for manholes :
19.18.1 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be
not less than 23 kg
Code Description Unit Quantity Rate Amount
Details of cost for one cover
MATERIAL
1355 Rectangular cover 455x610mm without
frame (low duty) each 1.00 910.00 910.00
9977 Carriage of C.I. Manhole cover L.S. 7.15 2.12 15.16
LABOUR
0114 Beldar day 0.12 645.00 77.40
TOTAL 1002.56 W
Add 1 % Water charges on "W" 10.03
TOTAL 1012.58 X
Add GST on "X" (multiplying
factor 0.1405) 142.27
TOTAL 1154.85 Y
Add 15% CPOH on "Y" 173.23
TOTAL 1328.08 Z
Add Cess @ 1% on "Z" 13.28
Cost for 1 cover 1341.36
Say 1341.35
19.18.2 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not
less than 58 kg
Code Description Unit Quantity Rate Amount
Details of cost for one cover
MATERIAL
1357 500 mm dia cover without frame
(medium duty) each 1.00 2300.00 2300.00
9977 Carriage of C.I. cover L.S. 13.47 2.12 28.56
SUB HEAD : 19- DRAINAGE 1863
Code Description Unit Quantity Rate Amount
LABOUR
0114 Beldar day 0.12 645.00 77.40
TOTAL 2405.96 W
Add 1 % Water charges on "W" 24.06
TOTAL 2430.02 X
Add GST on "X" (multiplying
factor 0.1405) 341.42
TOTAL 2771.43 Y
Add 15% CPOH on "Y" 415.71
TOTAL 3187.15 Z
Add Cess @ 1% on "Z" 31.87
Cost for 1 no. 3219.02
Say 3219.00
19.18.3 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less
than 108 kg
Code Description Unit Quantity Rate Amount
Details of cost for one cover
MATERIAL
3861 560 mm dia cover without frame
(Heavy duty) each 1.00 5100.00 5100.00
9977 Carriage of C.I. cover L.S. 16.12 2.12 34.17
LABOUR
0114 Beldar day 0.12 645.00 77.40
TOTAL 5211.57 W
Add 1 % Water charges on "W" 52.12
TOTAL 5263.69 X
Add GST on "X" (multiplying
factor 0.1405) 739.55
TOTAL 6003.24 Y
Add 15% CPOH on "Y" 900.49
TOTAL 6903.72 Z
Add Cess @ 1% on "Z" 69.04
Cost for 1 no. 6972.76
Say 6972.75
19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of
required shape and approved quality
19.19.1 L D- 2.5
19.19.1.1 Rectangular shape 600x450 mm internal dimensions
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7130 Rectangular shape 600x450 mm
precast R.C.C. manhole cover with
frame - L.D. - 2.5 each 1.00 675.00 675.00
SUB HEAD : 19- DRAINAGE 1864
Code Description Unit Quantity Rate Amount
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
1.00x0.85x0.15 = 0.1275 cum
Less cover with frame 0.85x0.70x0.15
= (-) 0.0893 cum
= 0.0382 cum Say 0.04 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.04 7365.15 294.61 A
9977 Carriage of R.C.C cover with frame L.S. 6.76 2.12 14.33
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 1012.60 W
Add 1 % Water charges on "W-A" 7.18
TOTAL 1019.78 X
Add GST on "X-A" (multiplying
factor 0.1405) 101.89
TOTAL 1121.67 Y
Add 15% CPOH on "Y-A" 124.06
TOTAL 1245.73 Z
Add Cess @ 1% on "Z-A" 9.51
Cost for 1 no. 1255.24
Say 1255.25
19.19.1.2 Square shape 450 mm internal dimensions
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7131 Square shape 450x450 mm precast
R.C.C. manhole cover with frame -
L.D. - 2.5 each 1.00 575.00 575.00
9977 Carriage of manhole cover L.S. 6.76 2.12 14.33
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
0.725x0.725x0.15 = 0.0788 cum
Less cover with frame
0.575x0.575x0.15 = (-) 0.0496 cum
= 0.0292 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 838.95 W
Add 1 % Water charges on "W-A" 6.18
TOTAL 845.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 87.70
TOTAL 932.82 Y
Add 15% CPOH on "Y-A" 106.78
TOTAL 1039.60 Z
Add Cess @ 1% on "Z-A" 8.19
Cost for 1 no. 1047.79
Say 1047.80
SUB HEAD : 19- DRAINAGE 1865
19.19.1.3 Circular shape 450 mm internal diameter
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7132 Circular shape 450 mm dia precast
R.C.C. manhole cover with frame -
L.D. - 2.5 each 1.00 575.00 575.00
9977 Carriage of manhole cover L.S. 6.76 2.12 14.33
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
3.14/4x(0.775)²x0.15 = 0.0708 cum
Less cover with frame
3.14/4x(0.625)²x0.15 = (-) 0.0460 cum
= 0.0248 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 838.95 W
Add 1 % Water charges on "W-A" 6.18
TOTAL 845.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 87.70
TOTAL 932.82 Y
Add 15% CPOH on "Y-A" 106.78
TOTAL 1039.60 Z
Add Cess @ 1% on "Z-A" 8.19
Cost for 1 no. 1047.79
Say 1047.80
19.19.2 M D - 10
19.19.2.1 Square shape 450 mm internal dimension
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7133 Rectangular shape 500x500 mm
precast R.C.C. manhole cover with
frame - M.D. - 10 each 1.00 670.00 670.00
9977 Carriage of manhole cover L.S. 6.76 2.12 14.33
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
0.95x0.95x0.15 = 0.1354 cum
Less cover with frame
0.80x0.80x0.15 = (-) 0.096 cum
= 0.0394 cum Say 0.04 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.04 7365.15 294.61 A
SUB HEAD : 19- DRAINAGE 1866
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 16.64 2.12 35.28
TOTAL 1014.21 W
Add 1 % Water charges on "W-A" 7.20
TOTAL 1021.41 X
Add GST on "X-A" (multiplying
factor 0.1405) 102.12
TOTAL 1123.53 Y
Add 15% CPOH on "Y-A" 124.34
TOTAL 1247.86 Z
Add Cess @ 1% on "Z-A" 9.53
Cost for 1 no. 1257.40
Say 1257.40
19.19.2.2 Circular shape 500 mm internal diameter
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7134 Circular shape 500 mm dia precast
R.C.C. manhole cover with frame -
M.D. - 10 each 1.00 575.00 575.00
9977 Carriage of manhole cover L.S. 6.76 2.12 14.33
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
3.14/4x(0.95)²x0.15 = 0.1064 cum
Less cover with frame
3.14/4x(0.8)²x0.15 = (-) 0.0754 cum
= 0.031 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
9999 Sundries L.S. 16.64 2.12 35.28
TOTAL 845.56 W
Add 1 % Water charges on "W-A" 6.25
TOTAL 851.81 X
Add GST on "X-A" (multiplying
factor 0.1405) 88.63
TOTAL 940.44 Y
Add 15% CPOH on "Y-A" 107.92
TOTAL 1048.37 Z
Add Cess @ 1% on "Z-A" 8.27
Cost for 1 no. 1056.64
Say 1056.65
19.19.3 H D - 20
19.19.3.1 Circular shape 560 mm internal diameter
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7135 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
H.D. - 20 each 1.00 880.00 880.00
SUB HEAD : 19- DRAINAGE 1867
Code Description Unit Quantity Rate Amount
9977 Carriage of manhole cover L.S. 13.52 2.12 28.66
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
3.14/4x(1.05)²x0.15 = 0.1299 cum
Less cover with frame
3.14/4x(0.9)²x0.15 = (-) 0.0955 cum
= 0.0344 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 1172.61 W
Add 1 % Water charges on "W-A" 9.52
TOTAL 1182.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 135.04
TOTAL 1317.17 Y
Add 15% CPOH on "Y-A" 164.43
TOTAL 1481.60 Z
Add Cess @ 1% on "Z-A" 12.61
Cost for 1 no. 1494.21
Say 1494.20
19.19.4 EHD - 35
19.19.4.1 Circular shape 560 mm internal dia
Code Description Unit Quantity Rate Amount
Details of cost for one no.
MATERIAL
7136 Circular shape 560 mm dia precast
R.C.C. manhole cover with frame -
E.H.D. - 35 each 1.00 1170.00 1170.00
9977 Carriage of manhole cover L.S. 13.52 2.12 28.66
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
3.14/4x(1.05)²x0.15 = 0.1299 cum
Less cover with frame
3.14/4x(0.9)²x0.15 = (-) 0.0955 cum
= 0.0344 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 1462.61 W
Add 1 % Water charges on "W-A" 12.42
TOTAL 1475.03 X
Add GST on "X-A" (multiplying
factor 0.1405) 176.20
TOTAL 1651.22 Y
Add 15% CPOH on "Y-A" 214.54
TOTAL 1865.76 Z
Add Cess @ 1% on "Z-A" 16.45
Cost for 1 no. 1882.21
Say 1882.20
SUB HEAD : 19- DRAINAGE 1868
19.20 Supplying and fixing C.I. cover 300x300 mm without frame for gully trap
(standard pattern) the weight of cover to be not less than 4.5 kg
Code Description Unit Quantity Rate Amount
Details of cost for one cover
MATERIAL
1353 C.I.cover without frame 300x300mm
inside i.e.cover of 4.50 kg each 1.00 477.00 477.00
9988 Carriage for cover L.S. 2.70 2.12 5.72
LABOUR
0114 Beldar day 0.03 645.00 19.35
TOTAL 502.07 W
Add 1 % Water charges on "W" 5.02
TOTAL 507.09 X
Add GST on "X" (multiplying
factor 0.1405) 71.25
TOTAL 578.34 Y
Add 15% CPOH on "Y" 86.75
TOTAL 665.09 Z
Add Cess @ 1% on "Z" 6.65
Cost for 1 cover 671.74
Say 671.75
19.21 Making connection of drain or sewer line with existing manhole including
breaking into and making good the walls, floors with cement concrete 1:2:4
mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse
sand), finished with a floating coat of neat cement and making necessary
channels for the drain etc. complete :
19.21.1 For pipes 100 to 250 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for one connection
MATERIAL
cement concrete 1:2:4 mix (1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
= 0.30x0.30x0.23 m = 0.0207 cum
Less pipe = 1/2x3.14x0.23x0.23x0.23
= 0.0096 cum
= 0.0111 cum Say 0.01 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete cum 0.01 7365.15 73.65 A
12 mm cement plater 1:3 ( 1 cement :
3 coarse sand ) finished with a floating
coat of neat cement
2x0.35x0.35 =0.25sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.25 386.55 96.64 A
LABOUR
(For cutting holes average size
30x30 cm in 23 cm thick wall and
making channel etc.)
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
SUB HEAD : 19- DRAINAGE 1869
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.25 645.00 161.25
9999 Add for delay sundries etc. L.S. 20.15 2.12 42.72
TOTAL 554.02 W
Add 1 % Water charges on "W-A" 3.84
TOTAL 557.85 X
Add GST on "X-A" (multiplying
factor 0.1405) 54.45
TOTAL 612.31 Y
Add 15% CPOH on "Y-A" 66.30
TOTAL 678.61 Z
Add Cess @ 1% on "Z-A" 5.08
Cost for 1 connection 683.69
Say 683.70
19.21.2 For pipes 250 to 300 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for one connection
MATERIAL
Cement concrete 1:2:4 mix ( 1 cement
: 2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
= 0.35x0.35x0.30 m = 0.037 cum
Less pipe = 1/2x3.14x0.30x0.30x
0.30 = 0.021 cum
= 0.016 cum Say 0.02 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.02 7365.15 147.30 A
12 mm cement plater 1:3 ( 1 cement :
3 coarse sand ) finished with a floating
coat of neat cement
2x0.40x0.40 =0.32 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.32 386.55 123.70 A
LABOUR
(For cutting holes average size 30x
30 cm in 23 cm thick wall and making
channel etc.)
0123 Mason (brick layer) 1st class day 0.12 784.00 94.08
0124 Mason (brick layer) 2nd class day 0.12 714.00 85.68
0114 Beldar day 0.25 645.00 161.25
9999 Add for delay sundries etc. L.S. 20.67 2.12 43.82
TOTAL 655.83 W
Add 1 % Water charges on "W-A" 3.85
TOTAL 659.68 X
Add GST on "X-A" (multiplying
factor 0.1405) 54.61
TOTAL 714.29 Y
Add 15% CPOH on "Y-A" 66.49
TOTAL 780.78 Z
Add Cess @ 1% on "Z-A" 5.10
Cost for 1 connection 785.88
Say 785.90
SUB HEAD : 19- DRAINAGE 1870
19.21.3 For pipes 350 to 450 mm diameter
Code Description Unit Quantity Rate Amount
Details of cost for one connection
MATERIAL
Cement concrete 1:2:4 mix ( 1 cement
: 2 coarse sand : 4 grade stone
aggregate 20 mm nominal size )
= 0.50x0.50x0.30 m = 0.075 cum
Less pipe = 1/2x3.14x0.45x0.45x
0.30 = 0.048 cum
= 0.027 cum Say 0.03 cum
4.1.3 Rate as per item no. 4.1.3 of
SH : Concrete Work cum 0.03 7365.15 220.95 A
12 mm cement plater 1:3 ( 1 cement :
3 coarse sand ) finished with a floating
coat of neat cement
2x0.55x0.55 =0.605 sqm Say 0.60 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.60 386.55 231.93 A
LABOUR
(For cutting holes average size
30x30 cm in 23 cm thick wall and
making channel etc.)
0123 Mason (brick layer) 1st class day 0.16 784.00 125.44
0124 Mason (brick layer) 2nd class day 0.16 714.00 114.24
0114 Beldar day 0.33 645.00 212.85
9999 Add for delay sundries etc. L.S. 26.91 2.12 57.05
TOTAL 962.46 W
Add 1 % Water charges on "W-A" 5.10
TOTAL 967.56 X
Add GST on "X-A" (multiplying
factor 0.1405) 72.31
TOTAL 1039.87 Y
Add 15% CPOH on "Y-A" 88.05
TOTAL 1127.92 Z
Add Cess @ 1% on "Z-A" 6.75
Cost for 1 connection 1134.67
Say 1134.65
19.22 Providing sand cast iron drop connection externally for 60 cm drop from branch
sewer line to main sewer manhole including inspection and cleaning eye with
chain and lid, sand cast iron drop pipe and bend encased all-round with cement
concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) with all centering and shuttering required, cutting holes in walls
and making good with brick work in cement mortar 1:4 (1 cement : 4 coarse
sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand) on inside
of the manhole wall, lead caulked joints between sand cast iron pipes and
fittings, stiff cement mortar 1:1 (1 cement : 1 fine sand) joints between sand
cast iron tee and S.W. pipe, making required channels complete as per standard
design and specifications :
SUB HEAD : 19- DRAINAGE 1871
19.22.1 100 mm dia sand cast iron drop connection
Code Description Unit Quantity Rate Amount
Details of cost for one drop connection
MATERIAL
1617 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
100mm dia each 0.55556 1135.00 630.56
= 38+30+33 =101 cm say 1 metre
Length of pipe = 1m. Hence, Qty
= 1 /1.8 =0.55556 Nos
9977 Carriage of pipe L.S. 1.43 2.12 3.03
Cutting charges
18.83.2 Rate as per item no 18.83.2 of
SH: Water supply each cut 3.00 160.70 482.10 A
1336 Clearing eye with chain and lid
100 mm dia each 1.00 44.00 44.00
1621 S.C.I. plain bend 100 mm dia each 1.00 280.00 280.00
1628 S.C.I. plain single equal junctions
100x100x100 mm dia each 1.00 405.00 405.00
Brick work in cement mortar
1:4 (1 cement : 4 coarse sand)
0.20x0.20x0.23 = 0.009 cum
Less pipe 1/2x3.14x0.10x0.10x0.23
= 0.002 cum
Net Qty= 0.009 - 0.002 = 0.007 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.007 6882.00 48.17 A
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.40x0.45x1.05 m = 0.189 cum
0.40x0.25x0.40 = 0.040 cum
Total= 0.229 cum
Less pipe portion
1/2x3.14x0.10x0.10x1.50 = 0.012 cum
Toothing portion
2x0.40x0.05x0.10 m = 0.004 cum
= 0.016 cum
Net Qty= 0.229-0.016 = 0.213 cum
Say 0.21 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.21 5660.45 1188.69 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
1x0.25x0.25 m = 0.0625 Say 0.06 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.06 386.55 23.19 A
Providing lead caulked joints to 100 mm
diameter pipe and special
12.39.1 Rate as per item no. 12.39.1 of
SH : Roofing each 4.00 444.05 1776.20 A
SUB HEAD : 19- DRAINAGE 1872
Code Description Unit Quantity Rate Amount
9999 Providing joint to S.W. pipe with
cement mortar 1:1 (1 cement : 1 fine
sand) L.S. 26.91 2.12 57.05
Form work
1.30x1.05 m = 1.36 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 1.36 669.55 910.59 A
9988 Sundries including carriage of bends etc. L.S. 26.91 2.12 57.05
LABOUR
For cutting holes 5 cm deep in
alternate course of brick work benching
and channel
0123 Mason (brick layer) 1st class day 0.70 784.00 548.80
0124 Mason (brick layer) 2nd class day 0.70 714.00 499.80
0114 Beldar day 2.70 645.00 1741.50
TOTAL 8695.74 W
Add 1 % Water charges on "W-A" 42.67
TOTAL 8738.41 X
Add GST on "X-A" (multiplying
factor 0.1405) 605.48
TOTAL 9343.89 Y
Add 15% CPOH on "Y-A" 737.24
TOTAL 10081.13 Z
Add Cess @ 1% on "Z-A" 56.52
Cost of one drop connection 10137.65
Say 10137.65
19.22.2 150 mm dia sand cast iron drop connection
Code Description Unit Quantity Rate Amount
Details of cost for one drop connection
MATERIAL
1618 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
150mm dia each 0.55556 1750.00 972.23
= 34.5+30+37 =101.5cm say 1.00m
Length of pipe = 1m. Hence, Qty
= 1 / 1.8 =0.55556 No.s
9977 Carriage of pipe L.S. 1.82 2.12 3.86
Cutting charges
18.83.4 Rate as per item no 18.83.4 of
SH Water Supply each cut 3.00 301.90 905.70 A
1337 Clearing eye with chain and lid
150 mm dia each 1.00 50.00 50.00
1622 S.C.I. plain bend 150 mm dia each 1.00 475.00 475.00
7087 S.C.I. Tee 150 mm each 1.00 570.00 570.00
Brick work in cement mortar
1:4 (1 cement : 4 coarse sand)
0.20x0.20x0.23 = 0.009 cum
Less pipe 1/2x3.14x0.15x0.15x0.23
= 0.004 cum
Net Qty= 0.005 cum
SUB HEAD : 19- DRAINAGE 1873
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.005 6882.00 34.41 A
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.45x0.50x1.15 m = 0.259 cum
0.45x0.25x0.45 = 0.0510 cum
= 0.310 cum
Less pipe portion
1/4x3.14x0.15x0.15x1.50 = 0.027 cum
Toothing portion
3x0.45x0.05x0.10 m = 0.004 cum
= 0.027 + 0.004 = 0.031 cum
Net Qty 0.310-0.031 = 0.279 cum.
Say 0.28 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete cum 0.28 5660.45 1584.93 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand) finished with floating
coat of neat cement
1x0.25x0.25 m = 0.0625 Say 0.06 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.06 386.55 23.19 A
Providing lead caulked joints to 150 mm
diameter pipe and special
12.39.2 Rate as per item no. 12.39.2 of
SH : Roofing each 4.00 604.65 2418.60 A
9999 Providing joint to S.W. pipe with
cement mortar 1:1 (1 cement : 1 fine
sand) L.S. 39.91 2.12 84.61
Form work
1.450x1.15 m = 1.67 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 1.67 669.55 1118.15 A
9988 Sundries including carriage of bends etc. L.S. 34.06 2.12 72.21
LABOUR
For cutting holes 45 holes 5 cm deep
toothing in alternate course of brick
work benching and making channel
0123 Mason (brick layer) 1st class day 0.85 784.00 666.40
0124 Mason (brick layer) 2nd class day 0.85 714.00 606.90
0114 Beldar day 3.50 645.00 2257.50
TOTAL 11843.68 W
Add 1 % Water charges on "W-A" 57.59
TOTAL 11901.27 X
Add GST on "X-A" (multiplying
factor 0.1405) 817.19
TOTAL 12718.46 Y
Add 15% CPOH on "Y-A" 995.02
TOTAL 13713.48 Z
Add Cess @ 1% on "Z-A" 76.29
Cost of one drop connection 13789.77
Say 13789.75
SUB HEAD : 19- DRAINAGE 1874
19.23 Extra for depths beyond 60 cm of sand cast iron drop connection complete:
19.23.1 For 100 mm dia sand cast iron drop connection
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
1617 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
100mm dia each 0.55556 1135.00 630.56
Length of pipe = 1m. Hence, Qty
= 1 / 1.8 = 0.55556 Nos.
9977 Carriage of material and fixing charges L.S. 13.39 2.12 28.39
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.40x0.45x1.00 mm = 0.18 cum
Less pipe portion
1/2x3.14x0.10x0.10x1.00 = 0.008 cum
Toothing portion
5x0.40x0.05x0.10 m = 0.010 cum
Total= 0.018 cum
Net Qty= 0.18-0.018 = 0.162 cum Say
0.16 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.16 5660.45 905.67 A
Form work
1.30x1.00 m = 1.30 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 1.30 669.55 870.42 A
9999 Sundries L.S. 7.15 2.12 15.16
LABOUR
For cutting holes 5 cm deep in alternate
course of brick work
0123 Mason (brick layer) 1st class day 0.04 784.00 31.36
0124 Mason (brick layer) 2nd class day 0.04 714.00 28.56
0114 Beldar day 0.04 645.00 25.80
TOTAL 2535.91 W
Add 1 % Water charges on "W-A" 7.60
TOTAL 2543.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 107.82
TOTAL 2651.33 Y
Add 15% CPOH on "Y-A" 131.29
TOTAL 2782.62 Z
Add Cess @ 1% on "Z-A" 10.07
Cost of one metre 2792.69
Say 2792.70
19.23.2 For 150 mm dia sand cast iron drop connection
Code Description Unit Quantity Rate Amount
Details of cost for one metre
MATERIAL
SUB HEAD : 19- DRAINAGE 1875
Code Description Unit Quantity Rate Amount
1618 S.C.I. soil, waste and vent single
socketed pipe 1.80 metres long:
150mm dia each 0.55556 1750.00 972.23
Length of pipe = 1m. Hence, Qty
= 1 / 1.8 = 0.55556 Nos.
9977 Carriage of material and fixing charges L.S. 13.39 2.12 28.39
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
0.45x0.50x1.00 mm = 0.225 cum
Less pipe portion
1/2x3.14x0.15x0.15x1.00 = 0.018 cum
Toothing portion
5x0.45x0.05x0.10 m = 0.011 cum
Total = 0.029 cum
Net 0.225-0.029 = 0.196 cum
Say 0.20 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.20 5660.45 1132.09 A
Form work
1.45x1.00 m = 1.45 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 1.45 669.55 970.85 A
9999 Sundries L.S. 8.09 2.12 17.15
LABOUR
For cutting 5 cm deep in alternate
course of brick work
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0114 Beldar day 0.05 645.00 32.25
TOTAL 3227.86 W
Add 1 % Water charges on "W-A" 11.25
TOTAL 3239.10 X
Add GST on "X-A" (multiplying
factor 0.1405) 159.63
TOTAL 3398.74 Y
Add 15% CPOH on "Y-A" 194.37
TOTAL 3593.11 Z
Add Cess @ 1% on "Z-A" 14.90
Cost of one metre 3608.01
Say 3608.00
19.24 Dismantling of manhole including R.C.C. top slab, C.I. cover with frame,
including stacking of useful materials near the site and disposal of
unserviceable materials within 50 m lead as per direction of Engineer-in-charge:
19.24.1 Rectangular manhole 90x80 cm and 45 cm deep
Code Description Unit Quantity Rate Amount
Details of cost of a manhole 90x80 cm
and 45 cm deep
Dismantling of cement concrete
1:4:8 (1 cement : 4 coarse sand 8 :
aggregate stone 40 mm nominal size)
1.51x1.41x0.20 m = 0.426 cum
Say 0.43 cum
SUB HEAD : 19- DRAINAGE 1876
Code Description Unit Quantity Rate Amount
15.2.2 Rate as per item no. 15.2.2 of
SH : Dismantling and demolishing cum 0.43 1239.60 533.03 A
Dismantling of secon class brick work
in cement mortar 1:4 (1 cement :
4 coarse sand)
4.32x0.23x0.35 m = 0.348 cum
Less for pipe 2x3.14x(0.15m)² x0.23m
= (-) 0.008 cum
Net Qty 0.348 - 0.008 = 0.340 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 0.34 1698.45 577.47 A
Dismantling cement concrete 1:2:4
( 1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size)
For benching 2x0.90x(0.80/2) x
(0.30+0.20)/2 = 0.18 cum
Less for pipe 1x0.90x3.14/4x(0.15m)²
= (-) 0.02 cum
Net qty= 0.16 cum
15.2.1 Rate as per item no. 15.2.1 of
SH : Dismantling and demolishing cum 0.16 2007.10 321.14 A
Dismantling of R.C.C slab of 1:2:4
(1 cement : 2 coarse sand : 4 grade
stone aggregate 20 mm nominal size)
For slab : 1.36x1.26x0.15m = 0.257 cum
Less for cover 0.61x0.455x0.15m
= (-) 0.042 cum
Net qty= 0.215 cum Say 0.22 cum
15.3 Rate as per item no 15.3 of
SH : Demolishing and dismantling cum 0.22 2928.10 644.18 A
9999 Removal of C.I. Cover with frame L.S. 7.15 2.12 15.16
TOTAL 2090.98 W
Add 1 % Water charges on "W-A" 0.15
TOTAL 2091.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.15
TOTAL 2093.28 Y
Add 15% CPOH on "Y-A" 2.62
TOTAL 2095.90 Z
Add Cess @ 1% on "Z-A" 0.20
Cost of one no 2096.10
Say 2096.10
19.24.2 Rectangular manhole 120x90 cm and 90 cm deep
Code Description Unit Quantity Rate Amount
Details of cost of a manhole 120x90
and 90 cm deep
Dismantling of cement concrete
1:4:8 (1 cement : 4 coarse sand 8 :
aggregate stone 40 mm nominal size)
1.81x1.51x0.20 m = 0.547 cum
Say 0.55 cum
SUB HEAD : 19- DRAINAGE 1877
Code Description Unit Quantity Rate Amount
15.2.2 Rate as per item no. 15.2.2 of
SH : Dismantling and demolishing cum 0.55 1239.60 681.78 A
Dismantling of secon class brick work
in cement mortar 1:4 (1 cement :
4 coarse sand)
5.12x0.23x0.80 m = 0.942 cum
Less for pipe 2x3.14x(0.15m)²x0.23 m
= (-) 0.008 cum
Net qty = 0.934 cum Say 0.93 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 0.93 1698.45 1579.56 A
Dismantling cement concrete 1:2:4
( 1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size)
2x1.20x0.90x(0.80/2) x (0.30+0.20)/2
= 2.70 cum
Less for pipe 1.20x3.14/4x(0.15m)²
= (-) 0.021 cum
= 0.249 cum say 0.25
15.2.1 Rate as per item no. 15.2.1 of
SH : Dismantling and demolishing cum 0.25 2007.10 501.78 A
Dismantling of R.C.C slab of 1:2:4
(1 cement : 2 coarse sand : 4 grade
stone aggregate 20 mm nominal size)
For slab : 1.66x1.36x0.15m = 0.339 cum
Less for cover 3.14/4x(0.50)²x0.15m
= (-) 0.029 cum
Net qty = 0.31 cum
15.3 Rate as per item no 15.3 of
SH : Demolishing and dismantling cum 0.31 2928.10 907.71 A
9999 Removal of C.I. Cover with frame L.S. 7.15 2.12 15.16
TOTAL 3685.98 W
Add 1 % Water charges on "W-A" 0.15
TOTAL 3686.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 2.15
TOTAL 3688.29 Y
Add 15% CPOH on "Y-A" 2.62
TOTAL 3690.90 Z
Add Cess @ 1% on "Z-A" 0.20
Cost of one no 3691.10
Say 3691.10
19.24.3 Rectangular arch type manhole 140x90 cm and 2.45 m deep
Code Description Unit Quantity Rate Amount
Details of cost of a manhole 140x90 cm
and 2.45 m deep
Dismantling of cement concrete
1:4:8 (1 cement : 4 coarse sand 8 :
aggregate stone 40 mm nominal size)
2.16m x 1.66m x 0.20m = 0.72 cum
SUB HEAD : 19- DRAINAGE 1878
Code Description Unit Quantity Rate Amount
15.2.2 Rate as per item no. 15.2.2 of
SH : Dismantling and demolishing cum 0.72 1239.60 892.51 A
Dismantling of second class brick work
in cement mortar 1:4 (1 cement :
4 coarse sand)
Brick work in item 5.52mx0.23mx1.20m
= 1.524 cum
3.92mx0.23mx1.15m = 1.037 cum
= 2.561 cum
Deduct arch ring and portion of pipe
2x½x3.14x0.25mx0.23x0.1m
= 0.018 cum
2x3.14/4(0.15)²x0.23m = 0.008 cum
= (-) 0.026 cum
Net qty = 2.561 - 0.026 = 2.535 cum
Say 2.54 cum
Brick work in arch
½x3.14x1.13x0.80x0.23m = 0.327 cum
2x½x3.14x0.25mx0.23x0.1m
= 0.018 cum
= 0.345 cum Say 0.35 cum
Net qty = 2.54+0.35 = 2.89 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 2.89 1698.45 4908.52 A
Dismantling cement concrete 1:2:4
( 1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size)
2x1.4x0.90/2x(0.20+0.30)/2 = 0.315 cum
Less pipe 1.4x3.14/4x(0.15)²
= (-) 0.025 cum
Net qty = 0.290 cum
15.2.1 Rate as per item no. 15.2.1 of
SH : Dismantling and demolishing cum 0.29 2007.10 582.06 A
Dismantling of R.C.C slab of 1:2:4
(1 cement : 2 coarse sand : 4 grade
stone aggregate 20 mm nominal size)
1.36mx1.06mx0.15 = 0.216 cum
Less cover 3.14/4x(0.50)²x0.15m
= (-) 0.029 cum
= 0.187 cum Say 0.19 cum
15.3 Rate as per item no 15.3 of
SH : Demolishing and dismantling cum 0.19 2928.10 556.34 A
9999 Removal of C.I. Cover with frame L.S. 7.15 2.12 15.16
9999 Removal of M.S foot rest L.S. 8.06 2.12 17.09
TOTAL 6971.68 W
Add 1 % Water charges on "W-A" 0.32
TOTAL 6972.00 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.58
TOTAL 6976.57 Y
Add 15% CPOH on "Y-A" 5.57
TOTAL 6982.15 Z
Add Cess @ 1% on "Z-A" 0.43
Cost of one no 6982.57
Say 6982.55
SUB HEAD : 19- DRAINAGE 1879
19.24.4 Circular manhole 122 cm diameter and 1.68 m deep
Code Description Unit Quantity Rate Amount
Details of cost of a manhole 1.22 m
internal diameter 1.68 m deep
Dismantling of cement concrete
1:3:6 (1 cement : 3 coarse sand : 6
aggregate stone 40 mm nominal size)
1.98x1.98x0.30 m = 1.178 cum
Say 1.18 cum
15.2.1 Rate as per item no 15.2.1 of
SH : Dismantling cum 1.18 2007.10 2368.38 A
Dismantling of second class brick work
in cement mortar 1:4 (1 cement :
4 coarse sand)
Curved on plan
3.14x1.45x0.24x0.23 = 0.251
3.14x(1.45+0.79)/2x1.32x0.23 = 1.069
= 1.320
Duduct arch ring and portion of pipe
2x½x3.14x0.25mx0.23x0.10 m
= 0.018 cum
2x3.14/4x(0.15)²x0.23 = 0.008 cum
= 0.026 cum
Net quantity 1.320-0.026 = 1.294
Say 1.29 cum
Brick work in arches
2x1/2x3.14x0.25 m x0.230x0.10 m
= 0.018 cum Say 0.02 cum
Total = 1.294+0.02 = 1.1.314 cum.
Say 1.131 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 1.31 1698.45 2224.97 A
Dismantaling cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 gradeed
stone aggregate 20 mm nominal size)
For benching :
3.14/4x(1.22)²x0.20 = 0.234 cum
[(2x8.133)/360]x(4/3)x3.14x(0.61)³
Total =0.043 cum
0.024 + 0.043 = 0.277 cum
Less pipe :1.22x3.14/4x(0.15)²
= (-) 0.0216 cum
Net Qty. = 0.277 - 0.0216 = 0.26 cum
In cover fixing 0.7854x1.020x1.020x
0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m :
= (-) 0.037 cum
= 0.086 cum Say 0.09 cum
Total = 0.26 + 0.09 = 0.35 cum
15.2.1 Rate as per item no 15.2.1 of
SH : Demolishing and dismantling cum 0.35 2007.10 702.49 A
9999 Removal of S.F.R.C cover with frame
size 560 mm diameter (medium duty) L.S. 7.15 2.12 15.16
SUB HEAD : 19- DRAINAGE 1880
Code Description Unit Quantity Rate Amount
9999 Removal of M.S. foot rests L.S. 8.06 2.12 17.09
TOTAL 5328.08 W
Add 1 % Water charges on "W-A" 0.32
TOTAL 5328.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.58
TOTAL 5332.98 Y
Add 15% CPOH on "Y-A" 5.57
TOTAL 5338.55 Z
Add Cess @ 1% on "Z-A" 0.43
Cost of one no 5338.97
Say 5338.95
19.25 Extra for depth of manholes dismantled :
19.25.1 Rectangular manhole 90x80 cm and beyond 45 cm depth
Code Description Unit Quantity Rate Amount
Details of cost for one metre
Dismantling of second class brick work
in cement mortar 1:5 (1 Cement : 5 fine
sand)
4.32x0.23x1.0m = 0.994 cum
Say 0.99 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 0.99 1698.45 1681.47 A
9999 Removing of M.S. foot rests L.S. 1.82 2.12 3.86
TOTAL 1685.32 W
Add 1 % Water charges on "W-A" 0.04
TOTAL 1685.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 0.55
TOTAL 1685.91 Y
Add 15% CPOH on "Y-A" 0.67
TOTAL 1686.58 Z
Add Cess @ 1% on "Z-A" 0.05
Cost for one metre 1686.63
Say 1686.65
19.25.2 Rectangular manhole 120x90 cm and beyond 90 cm depth
Code Description Unit Quantity Rate Amount
Details of cost for one metre
Dismantling of second class brick work
in cement mortar 1:5 (1 Cement : 5 fine
sand)
5.12x0.23x1.0m = 1.178 cum
Say 1.18 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 1.18 1698.45 2004.17 A
SUB HEAD : 19- DRAINAGE 1881
Code Description Unit Quantity Rate Amount
9999 Removing of M.S. foot rests L.S. 1.82 2.12 3.86
TOTAL 2008.03 W
Add 1 % Water charges on "W-A" 0.04
TOTAL 2008.07 X
Add GST on "X-A" (multiplying
factor 0.1405) 0.55
TOTAL 2008.62 Y
Add 15% CPOH on "Y-A" 0.67
TOTAL 2009.28 Z
Add Cess @ 1% on "Z-A" 0.05
Cost for one metre 2009.33
Say 2009.35
19.25.3 Rectangular arch type manhole 140x90 cm and beyond 2.45 m depth (up to
4.25 m depth)
Code Description Unit Quantity Rate Amount
Details of cost for 1.80 metre
Dismantling IInd class brick work in
cement mortar 1:4 (1 Cement : 4
Coarse sand) for 2.45 depth
Qty for 2.45m depth
5.52mx0.23mx1.20m = 1.524 cum
3.92mx0.23mx1.15m = 1.037 cum
Total = 2.561 cum
Deduct arch ring and portion of pipe
2x½x3.14x0.25mx0.23x0.1m
= 0.018 cum
2x3.14/4(0.15)²x0.23m = 0.008 cum
Total deduction= = (-) 0.026 cum
Net 2.561 - 0.026 = 2.535 cum
Say 2.54 cum
Qty in arch
½x3.14x1.13x0.80x0.23m = 0.327 cum
2x½x3.14x0.25mx0.23x0.1m
= 0.018 cum
Total = 0.345 cum Say 0.35 cum
Totol for 4.45 m depth 2.54 + 0.35
= 2.89 cum
Qty for 4.25m depth
5.52mx0.23mx1.20m = 1.524 cum
3.92mx0.23mx2.95m = 2.660 cum
Total = 4.184 cum
Deduct arch ring and portion of pipe
2x½x3.14x0.70mx0.23x0.1m
= 0.051 cum
2x3.14/4x(0.60)²x0.23 = 0.130 cum
Total deduction== (-) 0.181 cum
Net 4.184 - 0.181 = 4.003 cum
Say 4.00 cum
Qty in arch
½x3.14x1.13x0.80x0.23m = 0.327 cum
SUB HEAD : 19- DRAINAGE 1882
Code Description Unit Quantity Rate Amount
2x½x3.14x0.70mx0.23x0.1m
= 0.051 cum
Total = 0.378 cum Say 0.38 cum
Total for 2.25 m depth = 4.0+ 0.38
=4.38 cum
Net difference = 4.38 - 2.89 = 1.49 cum
15.7.4 Rate as per item no. 15.7.4 of
SH :dismantling and dimolishing cum 1.49 1698.45 2530.69 A
Dismantling cement concrete 1:2:4
(1 Cement : 2 coarse sand : 4 graded
stone aggregate 40mm nominal size)
Qty for 4.25m depth
2x1.4x(0.90/2)x(0.65+0.75)/2
= 0.882 cum
Less pipe :1.4x3.14/4x(0.60)²(-)
= 0.396 cum
= 0.486 cum Say 0.49 cum
Qty for 2.45m depth
2x1.4x(0.90/2)x(0.20+0.30)/2
= 0.315 cum
Less pipe :1.4x3.14/4x(0.15)²(-)
= 0.025 cum
= 0.290 cum Say 0.29 cum
Net difference = 0.49 - 0.29 = 0.20 cum
15.2.1 Rate as per item no 15.2.1 of
SH : Demolishing and dismantling cum 0.20 2007.10 401.42 A
Cost for 1.8 metre depth 2932.11
Cost for 1 metre depth 1628.95
Say 1628.95
19.25.4 Circular manhole 122 cm diameter and beyond 1.68 m depth (up to 2.29 m
depth)
Code Description Unit Quantity Rate Amount
Details of cost for 0.61 metre
Dismantling cement concrete 1:3:6
(1 Cement : 3 coarse sand : 6 graded
stone aggregate 40mm nominal size)
1.98x1.98x0.30 = 1.178 cum.
Say 1.18 cum.
15.2.1 (Rate as per item No.15.2.1 of
SH. dismantling and Demolishing) cum 1.18 2007.10 2368.38 A
Dismantling IInd class brick work in
cement mortar 1:4 (1 Cement :
4 Coarse sand)
Curved on plan
3.14x1.45x0.85x0.23 = 0.891
3.14x(1.45+0.79)/2x1.32x0.23 = 1.069
Total = 0.891 + 1.069 = 1.96 cum
Duduct arch ring and portion of pipe
2x1/2x3.14x0.25mx0.23x0.10 m
= 0.018 cum
SUB HEAD : 19- DRAINAGE 1883
Code Description Unit Quantity Rate Amount
2x3.14/4x(0.15)²x0.23 = 0.008 cum
Total deduction = 0.026 cum
Net quantity 1.96-0.026 = 1.934
Say 1.93 cum
Qty in arch
2x1/2x3.14x0.25 m x0.23x0.10 m
= 0.018 cum Say 0.02 cum
Total = 1.93 + 0.02 = 1.97 cum
15.7.4 Rate as per item no 15.7.4 of
SH : Dismantling and demolishing cum 1.97 1698.45 3345.95 A
Dismantling cemnet concrete 1:2:4
( 1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size
For benching :
3.14/4x(1.22)²x0.20 = 0.234 cum
[(2x8.133)/360]x(4/3)x3.14x(0.61)³
=0.043 cum
= 0.277 cum
Less pipe :1.22x3.14/4x(0.15)²(-)
= 0.0216 cum
Net qty== 0.2554 cum Say 0.26 cum
For fixing cover : 3.14/4 x d2 x thickness
0.7854x1.020x1.020x0.15 m =0.123 cum
Less cover 3.14/4x(0.28)² x 0.15 m :
= (-)0.037 cum
Net qty= 0.086 cum Say 0.09 cum
Total = 0.26 + 0.09 = 0.35 cum
15.2.1 Rate as per item no 15.2.1 of
SH : Dismantling cum 0.35 2007.10 702.49 A
9999 Removal of SFRC cover L.S. 7.15 2.12 15.16
9999 Removal of M.S. foot rests L.S. 8.09 2.12 17.15
Deduct cost of dismantling manhole
1.68m deep
19.24.4 Rate as per Item No.19.24.4 of
SH: DRAINAGE each -1.00 5338.95 -5338.95 A
TOTAL 1110.17 W
Add 1 % Water charges on "W-A" 0.32
TOTAL 1110.49 X
Add GST on "X-A" (multiplying
factor 0.1405) 4.58
TOTAL 1115.08 Y
Add 15% CPOH on "Y-A" 5.58
TOTAL 1120.66 Z
Add Cess @ 1% on "Z-A" 0.43
Cost of manhole 0.61m depth 1121.09
Cost per metre depth 1837.85
Say 1837.85
SUB HEAD : 19- DRAINAGE 1884
19.26 Raising manhole cover and frame slab to required level including dismantling
existing slab and making good the damage as required (Raising depth of
manhole to be paid separately) :
19.26.1 Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm of grade
LD - 2.5
Code Description Unit Quantity Rate Amount
Details of cost for one manhole
Dismantling of R.C.C slab of 1:1.5:3
(1 cement : 1.5 coarse sand (Zone -
III): 3 aggregate stone 20 mm nominal
size) = 1.36x1.26x0.15 = 0.257 cum
Less cover with frame portion
0.85x0.70x0.15 =(-) 0.089 cum
Net qty=0.168 cum Say 0.17 cum
15.3 Rate as per item no. 15.3 of
SH : Dismantling and demolishing cum 0.17 2928.10 497.78 A
9999 Removal of R.C.C cover and frame L.S. 7.15 2.12 15.16
Removal of R.C.C work 1:1.5:3 ( 1
cement : 1.5 coarse sand : 3 graded
stone aggregate 20 mm nominal size )
For raised slab = 1.36x1.26x0.15
= 0.257 cum
Less portion cover with frame
= 0.85x0.70x0.15 =(-) 0.089 cum
Net qty = 0.168 cum Say 0.17 cum
5.3 Rate as per item no. 5.3 of
SH : RCC work cum 0.17 10719.30 1822.28 A
Form work = 0.90x0.80 = 0.72 sqm
Less cover = 0.60x0.45 =(-) 0.27 sqm
Net qty = 0.45 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC work sqm 0.45 766.55 344.95 A
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 2708.83 W
Add 1 % Water charges on "W-A" 0.44
TOTAL 2709.26 X
Add GST on "X-A" (multiplying
factor 0.1405) 6.22
TOTAL 2715.48 Y
Add 15% CPOH on "Y-A" 7.57
TOTAL 2723.05 Z
Add Cess @ 1% on "Z-A" 0.58
Cost of one no 2723.63
Say 2723.65
19.26.2 Rectangular manhole 120x90 cm with circular cover 500 mm dia of grade MD - 10
Code Description Unit Quantity Rate Amount
Details of cost for one manhole
Dismantling of R.C.C slab of 1:1.5:3
(1 cement : 1.5 coarse sand : 3
aggregate stone 20 mm nominal size)
1.66x1.36x0.15 = 0.339 cum
SUB HEAD : 19- DRAINAGE 1885
Code Description Unit Quantity Rate Amount
Less for R.C.C cover with frame
3.14/4x(0.80)²x0.15 =(-) 0.075 cum
Net qty 0.264 cum Say 0.26 cum
15.3 Rate as per item no. 15.3 of
SH : Dismantling and demolishing cum 0.26 2928.10 761.31 A
9999 Removal of R.C.C cover and frame L.S. 7.15 2.12 15.16
R.C.C work 1:1.5:3 ( 1 cement :
1.5 coarse sand : 3 graded stone
aggregate 20 mm nominal size )
1.66x1.36x0.15 = 0.339 cum
Less portion cover with frame
= 3.14/4x0.80x0.80x0.15 =(-) 0.075 cum
Net qty= 0.264 cum Say 0.26 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.26 10719.30 2787.02 A
Form work = 1.2x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.50)²
=(-) 0.196 sqm
Net qty= 0.884 sqm Say .88 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC work sqm 0.88 766.55 674.56 A
9999 Sundries L.S. 16.64 2.12 35.28
TOTAL 4273.32 W
Add 1 % Water charges on "W-A" 0.50
TOTAL 4273.83 X
Add GST on "X-A" (multiplying
factor 0.1405) 7.16
TOTAL 4280.98 Y
Add 15% CPOH on "Y-A" 8.71
TOTAL 4289.70 Z
Add Cess @ 1% on "Z-A" 0.67
Cost of one no 4290.37
Say 4290.35
19.26.3 Rectangular manhole 120x90 cm with circular cover 560 mm dia of grade HD - 20
Code Description Unit Quantity Rate Amount
Details of cost for one manhole
Dismantling of R.C.C slab of 1:1.5:3
(1 cement : 1.5 coarse sand : 3
aggregate stone 20 mm nominal size)
1.66x1.36x0.15 = 0.339 cum
Less for R.C.C cover with frame
3.14/4x(0.90)²x0.15 =(-) 0.095 cum
Net qty 0.244 cum Say 0.24 cum
15.3 Rate as per item no 15.3 of
SH : Dismantling and demolishing cum 0.24 2928.10 702.74 A
SUB HEAD : 19- DRAINAGE 1886
Code Description Unit Quantity Rate Amount
9999 Removal of R.C.C cover and frame L.S. 7.15 2.12 15.16
R.C.C work 1:1.5:3 ( 1 cement :
1.5 coarse sand : 3 graded stone
aggregate 20 mm nominal size )
1.66x1.36x0.15 = 0.339 cum
Less portion cover with frame
= 3.14/4x0.90x0.90x0.15
=(-) 0.095 cum
Net qty= 0.244 cum Say 0.24 cum
5.3 Rate as per item no 5.3 of
SH : RCC Work cum 0.24 10719.30 2572.63 A
Form work = 1.2x0.90 = 1.08 sqm
Less cover = 3.14/4x(0.56)²
=(-) 0.246 sqm
Net qty= 0.834 sqm Say .83 sqm
5.9.3 Rate as per item no 5.9.3 of
SH : RCC work sqm 0.83 766.55 636.24 A
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 3969.76 W
Add 1 % Water charges on "W-A" 0.58
TOTAL 3970.35 X
Add GST on "X-A" (multiplying
factor 0.1405) 8.25
TOTAL 3978.60 Y
Add 15% CPOH on "Y-A" 10.05
TOTAL 3988.65 Z
Add Cess @ 1% on "Z-A" 0.77
Cost of one no 3989.42
Say 3989.40
19.26.4 Circular manhole 140 cm dia with circular cover 600 mm dia of grade EHD - 35
Code Description Unit Quantity Rate Amount
Details of cost for one manhole
Dismantling of C.C slab of 1:2:4
(1 cement 2 coarse sand : 4 aggregate
stone 20 mm nominal size)
= 3.14/4x(0.985)²x0.15 = 0.114 cum
Less cover =3.14/4x(0.90)²x0.15
=(-) 0.095 cum
Net qty= 0.019 cum Say 0.02 cum
15.3 Rate as per item no. 15.3 of
SH : Dismantling and demolishing cum 0.02 2928.10 58.56 A
9999 Removal of R.C.C cover and frame L.S. 8.06 2.12 17.09
C.C work 1:2:4 ( 1 cement : 2 coarse
sand 4 graded stone aggregate 20 mm
nominal size )
3.14/4x(0.985)²x0.15 = 0.114 cum
Less portion cover with frame
= 3.14/4x(0.90)²x0.15 =(-) 0.095 cum
Net qty= 0.019 cum Say 0.02 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.02 9375.20 187.50 A
SUB HEAD : 19- DRAINAGE 1887
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 20.28 2.12 42.99
TOTAL 306.15 W
Add 1 % Water charges on "W-A" 0.60
TOTAL 306.75 X
Add GST on "X-A" (multiplying
factor 0.1405) 8.53
TOTAL 315.27 Y
Add 15% CPOH on "Y-A" 10.38
TOTAL 325.65 Z
Add Cess @ 1% on "Z-A" 0.80
Cost of one no 326.45
Say 326.45
19.27 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast
R.C.C. horizontal grating with frame complete as per standard design :
19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
MATERIAL
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.11mx1.06mx0.15 m= 0.176 cum
Say 0.18 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.18 5660.45 1018.88 A
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 coarse sand)
2.82 m x 0.23m x0.45 m = 0.29 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.29 6882.00 1995.78 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 1.90x0.45 m = 0.855 sqm
Bed : 0.45x0.50 m = 0.225 sqm
Total= 1.080 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.08 386.55 417.47 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
2.82x0.23x0.15 m = 0.097 cum
Say 0.10 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete cum 0.10 9375.20 937.52 A
Form work
3.50x0.15 m = 0.525 sqm
Say 0.53 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 0.53 669.55 354.86 A
SUB HEAD : 19- DRAINAGE 1888
Code Description Unit Quantity Rate Amount
7380 Precast R.C.C. grating with frame
500x450 mm horizontal grating each 1.00 620.00 620.00
9977 Carriage of R.C.C. grating L.S. 7.15 2.12 15.16
9999 Fixing R.C.C. grating L.S. 5.33 2.12 11.30
TOTAL 5370.97 W
Add 1 % Water charges on "W-A" 6.46
TOTAL 5377.44 X
Add GST on "X-A" (multiplying
factor 0.1405) 91.74
TOTAL 5469.17 Y
Add 15% CPOH on "Y-A" 111.70
TOTAL 5580.87 Z
Add Cess @ 1% on "Z-A" 8.56
Cost of one chamber 5589.44
Say 5589.45
19.28 Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating
complete as per standard design :
19.28.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.06mx1.06mx0.15 m= 0.17 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.17 5660.45 962.28 A
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 coarse sand)
2.72 m x 0.23m x0.70 m = 0.438 cum
Deduct opening 0.45x0.23x0.10 m
= 0.01 cum
Block 3x(0.075)³ = 0.001 cum
Total deduction = 0.011 cum
Net qty. = 0.438 (-) 0.011 = 0.427 cum
Say 0.43 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.43 6882.00 2959.26 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 1.80x0.70 m = 1.26 sqm
Bed : 0.45x0.45 m = 0.202 sqm
Top : 0.45x0.20 m = 0.09 sqm
Sides : 2x0.20x0.10 m = 0.04 sqm
Total= 1.592 sqm
Deduct opening
0.45x0.10 m = 0.045 sqm
Net qty. = 1.592 (-) 0.045 = 1.547 cum
Say 1.55 cum
SUB HEAD : 19- DRAINAGE 1889
Code Description Unit Quantity Rate Amount
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.55 386.55 599.15 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
Block = 3x(0.75)³ = 0.001 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete cum 0.001 9375.20 9.38 A
R.C.C. 1:1.5:3 (1 cement : 1.5 coarse
sand : 3 graded stone aggregate
20 mm nominal size)
0.91x0.91x0.075 m = 0.062 cum
Say 0.06 cum
5.3 Rate as per item no. 5.3 of
SH : RCC work cum 0.06 10719.30 643.16 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.113 645.00 -72.89
Form work
0.45x0.45 m = 0.202 sqm
0.45x0.20 m = 0.09 sqm
outside slab : 3.40x0.075 m
= 0.255 sqm
Total= 0.547 sqm Say 0.55 sqm
5.9.2 Rate as per item no 5.9.2 of
SH : RCC sqm 0.55 669.55 368.25 A
Mild steel reinforcement for
R.C.C work
0.062 cum @ 80 kg/cum = 4.96 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 4.96 88.95 441.19 A
7381 Precast R.C.C. grating with frame
450x100 mm vertical grating each 1.00 235.00 235.00
9999 Fixing and carriage of R.C.C. grating L.S. 20.67 2.12 43.82
TOTAL 6188.60 W
Add 1 % Water charges on "W-A" 2.06
TOTAL 6190.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 29.22
TOTAL 6219.88 Y
Add 15% CPOH on "Y-A" 35.58
TOTAL 6255.47 Z
Add Cess @ 1% on "Z-A" 2.73
Cost of one chamber 6258.20
Say 6258.20
SUB HEAD : 19- DRAINAGE 1890
19.29 Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement
mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal
grating with frame and vertical grating complete as per standard design :
19.29.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.71mx1.11mx0.15 m = 0.285 cum
Say 0.29 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.29 5660.45 1641.53 A
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 coarse sand)
1.91 m x 0.23m x0.45 m = 0.199 cum
2.20mx0.23mx0.70 m = 0.354 cum
Total= 0.553 cum
Deduct lintel portion
2x0.23x0.20x0.20 m = (-) 0.018 cum
Nte Qty= 0.0535 cum Say 0.54 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.54 6882.00 3716.28 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 1.80x0.70 m = 1.26 sqm
Wall : 1.40x0.45 m = 0.63 sqm
Bed : 1.10x0.50 m = 0.55 sqm
Total= 2.44 sqm
Deduct 2x0.20x0.20 m = (-) 0.08 sqm
Net Qty= 2.36 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.36 386.55 912.26 A
Cement concrete 1:2:4 ( 1 cement :
2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
Block = 1.92x0.23x0.15 = 0.07 cum
4.2.3 Rate as per item no 4.2.3 of
SH : Concrete Work cum 0.07 9375.20 656.26 A
R.C.C. 1:1.5:3 (1 cement : 1.5 coarse
sand : 3 graded stone aggregate
20 mm nominal size)
0.88x0.96x0.075 m = 0.063 cum
Say 0.06 cum
5.3 Rate as per item no. 5.3 of
SH : RCC work cum 0.06 10719.30 643.16 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.113 645.00 -72.89
R.C.C. 1:1.5:3 (1 cement: 1.5 coarse
sand : 3 graded stone aggregate
20 mm nominal size) in lintels
1x0.96x0.20x0.20 m = 0.04 cum
SUB HEAD : 19- DRAINAGE 1891
Code Description Unit Quantity Rate Amount
5.13 Rate as per item no. 5.13 of
SH : RCC work cum 0.04 13581.85 543.27 A
Form work
Slab bottom 0.50x0.65 m = 0.325 sqm
Outer periphery 3.50x0.075 m
= 0.263 sqm
2.20x0.15 m = 0.330 sqm
= 0.918 sqm Say 0.91 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 0.91 669.55 609.29 A
Mild steel reinforcement for R.C.C work
(0.06+0.04) = 0.10 cum @ 80 kg/cum
= 8.00 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 8.00 88.95 711.60 A
7380 Precast R.C.C. grating with frame
500x450 mm horizontal grating each 1.00 620.00 620.00
9977 Carriage of R.C.C. grating L.S. 7.15 2.12 15.16
7381 Precast R.C.C. grating with frame
450x100 mm vertical grating each 1.00 235.00 235.00
9999 Labour for fixing precast R.C.C. grating
and frame L.S. 34.06 2.12 72.21
TOTAL 10303.14 W
Add 1 % Water charges on "W-A" 8.69
TOTAL 10311.83 X
Add GST on "X-A" (multiplying
factor 0.1405) 123.38
TOTAL 10435.21 Y
Add 15% CPOH on "Y-A" 150.23
TOTAL 10585.45 Z
Add Cess @ 1% on "Z-A" 11.52
Cost of one chamber 10596.97
Say 10596.95
19.30 Constructing brick masonry chamber for underground C.I. inspection chamber and
bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with
frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame
to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top
slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm
nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone
aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on
walls and bed concrete etc. complete as per standard design:
19.30.1 Inside dimensions 455x610 mm and 45 cm deep for single pipe line :
19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one chamber
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.22mx1.065mx0.15 m= 0.195 cum
Say 0.20 cum
SUB HEAD : 19- DRAINAGE 1892
Code Description Unit Quantity Rate Amount
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.20 5660.45 1132.09 A
Brick work in bricks of clas designation
7.5 in cement mortar 1:4 ( 1 cement :
4 coarse sand)
3.05 m x 0.23m x0.30 m = 0.210 cum
Less pipe
2x3.14/4x(0.10)²x0.23 m = (-) 0.004 cum
Net Qty= 0.206 cum Say 0.21 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.21 6882.00 1445.22 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 2.13x0.30 m = 0.639 sqm
Bed : 0.61x0.455 m = 0.278 sqm
Total= 0.917 sqm
Less pipe 2x3.14/4x(0.10)²
= (-) 0.016 sqm
Net Qty= 0.901 sqm Say 0.90 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 0.90 386.55 347.90 A
Cement concrete 1:1.5:3 ( 1 cement :
1.5 coarse sand : 3 graded stone
aggregate 20 mm nominal size)
3.05x0.23x0.15 = 0.105 cum
say 0.11 cum
5.3 Rate as per item no 5.3 of SH : RCC cum 0.11 10719.30 1179.12 A
Form work
Outer periphery 3.73x0.15 m = 0.56 sqm
5.9.2 Rate as per item no 5.9.2 of SH : RCC sqm 0.56 669.55 374.95 A
1354 Rectangular cover 455x610 mm with
frame (low duty) each 1.00 1400.00 1400.00
9977 Carriage of C.I.cover and frame L.S. 7.15 2.12 15.16
9999 Painting of C.I. Cover and frame
with coal tar L.S. 7.15 2.12 15.16
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 5938.25 W
Add 1 % Water charges on "W-A" 14.59
TOTAL 5952.84 X
Add GST on "X-A" (multiplying
factor 0.1405) 207.04
TOTAL 6159.88 Y
Add 15% CPOH on "Y-A" 252.09
TOTAL 6411.97 Z
Add Cess @ 1% on "Z-A" 19.33
Cost of one chamber 6431.30
Say 6431.30
SUB HEAD : 19- DRAINAGE 1893
19.30.2 Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :
19.30.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost of one no.
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.31mx1.11mx0.15 m= 0.22 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.22 5660.45 1245.30 A
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 fine sand)
3.32 m x 0.23m x0.30 m = 0.229 cum
Less pipe
3x3.14x(0.10)²x0.23 m = (-) 0.005 cum
Net Qty= 0.224 cum Say 0.22 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.22 6882.00 1514.04 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 2.40x0.30 m = 0.72 sqm
Bed : 0.70x0.50 m = 0.35 sqm
= 1.07 sqm
Less pipe 3x3.14/4x(0.10)² = (-) 0.02 sqm
Net Qty= 1.05 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.05 386.55 405.88 A
R.C.C 1:1.5:3 ( 1 cement : 1.5 coarse
sand : 3 graded stone aggregate
20 mm nominal size)
1.16x0.96x0.15 = 0.167 cum
Deduct cover
0.61x0.45x0.15 m = (-) 0.042 cum
Net Qty= 0.125 cum Say 0.13 cum
5.3 Rate as per item no. 5.3 of
SH : RCC work cum 0.13 10719.30 1393.51 A
Form work
Inside area of chamber : 0.70x0.50 m
= 0.35 sqm
Outer periphery 4.00x0.15 m
= 0.60 sqm = 0.95 sqm
Deduct cover : 0.61x0.455 m
= (-) 0.278 sqm
= 0.672 sqm Say 0.67 sqm
5.9.2 Rate as per item no 5.9.2 of
SH : RCC sqm 0.67 669.55 448.60 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.24 645.00 -154.80
M.S.reinforcement for slab
0.13 cum @ 48.06 kg/cum = 6.25 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 6.25 88.95 555.94 A
SUB HEAD : 19- DRAINAGE 1894
Code Description Unit Quantity Rate Amount
1354 Rectangular cover 455x610 mm
with frame (low duty) each 1.00 1400.00 1400.00
9977 Carriage of C.I. Cover and frame L.S. 7.15 2.12 15.16
9999 Painting of C.I. Cover and frame with
coal tar L.S. 7.15 2.12 15.16
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 6867.44 W
Add 1 % Water charges on "W-A" 13.04
TOTAL 6880.48 X
Add GST on "X-A" (multiplying
factor 0.1405) 185.07
TOTAL 7065.55 Y
Add 15% CPOH on "Y-A" 225.34
TOTAL 7290.89 Z
Add Cess @ 1% on "Z-A" 17.28
Cost of one chamber 7308.17
Say 7308.15
19.30.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more
inlets :
19.30.3.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost of one chamber
Cement concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone
aggregate 40 mm nominal size)
1.46mx1.21mx0.15 m= 0.26 cum
4.1.11 Rate as per item no 4.1.11 of
SH : Concrete Work cum 0.26 5660.45 1471.72 A
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 coarse sand)
3.82 m x 0.23m x0.30 m = 0.26 cum
Less pipe
5x3.14x(0.10)²x0.23 m = (-) 0.009 cum
Net Qty= 0.255 cum Say 0.26 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.26 6882.00 1789.32 A
12 mm cement plaster 1:3 ( 1 cement :
3 coarse sand) finished with floating
coat of neat cement
Wall : 2.90x0.30 m = 0.87 sqm
Bed : 0.85x0.60 m = 0.51 sqm
Total= 1.38 sqm
Less pipe 5x3.14/4x(0.10)²
= (-) 0.04 sqm
Net Qty= 1.34 sqm
SUB HEAD : 19- DRAINAGE 1895
Code Description Unit Quantity Rate Amount
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 1.34 386.55 517.98 A
R.C.C 1:1.5:3 ( 1 cement : 1.5 coarse
sand : 3 graded stone aggregate
20 mm nominal size)
1.31x1.06x0.15 = 0.208 cum
Deduct cover
0.61x0.455x0.15 m = (-) 0.042 cum
Net Qty= 0.166 cum Say 0.17 cum
5.3 Rate as per item no. 5.3 of
SH : RCC work cum 0.17 10719.30 1822.28 A
Less labour for not lifting the materilas
upto floor five level
0115 Coolie day -0.32 645.00 -206.40
Form work
Inside area of chamber : 0.85x0.60 m
= 0.511 sqm
Outer periphery 4.50x0.15 m
= 0.675 sqm
Total= 1.186 sqm
Deduct cover : 0.61x0.455 m
= (-) 0.278 sqm
Net Qty= 0.908 sqm Say 0.91 sqm
5.9.2 Rate as per item no 5.9.2 of
SH : RCC sqm 0.91 669.55 609.29 A
M.S.reinforcement for slab for
0.17 cum
@ 48.06 kg/cum
= 48.06x0.17cum = 8.17 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 8.17 88.95 726.72 A
1354 Rectangular cover 455x610 mm
with frame (low duty) each 1.00 1400.00 1400.00
9977 Carriage of C.I. Cover and frame L.S. 7.15 2.12 15.16
9999 Painting of C.I. Cover and frame with
coal tar L.S. 7.15 2.12 15.16
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 8189.89 W
Add 1 % Water charges on "W-A" 12.53
TOTAL 8202.41 X
Add GST on "X-A" (multiplying
factor 0.1405) 177.75
TOTAL 8380.16 Y
Add 15% CPOH on "Y-A" 216.43
TOTAL 8596.59 Z
Add Cess @ 1% on "Z-A" 16.59
Cost of one chamber 8613.18
Say 8613.20
SUB HEAD : 19- DRAINAGE 1896
19.31 Extra for depth beyond 45 cm of brick masonry chamber :
19.31.1 For 455x610 mm size
19.31.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one metre
Brick work in bricks of clas designation
7.5 in cement mortar 1:4 ( 1 cement :
4 coarse sand)
3.05 m x 0.23m x1.00 m = 0.70 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.70 6882.00 4817.40 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand finished with floating
coat of neat cement
Wall : 2.13x1.00 m = 2.13 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.13 386.55 823.35 A
TOTAL 5640.75
Cost per metre 5640.75
Say 5640.75
19.31.2 For 500x700 mm size
19.31.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one metre
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement : 4 fine sand)
3.32 m x 0.23m x1.00 m = 0.76 cum
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.76 6882.00 5230.32 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand finished with floating
coat of neat cement
Wall : 2.40x1.00 m = 2.40 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.40 386.55 927.72 A
TOTAL 6158.04
Cost per metre 6158.04
Say 6158.05
19.31.3 For 600x850 mm size
19.31.3.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one metre
Brick work in bricks of class
designation 7.5 in cement mortar
1:4 ( 1 cement: 4 coarse sand)
3.82 m x 0.23m x1.00 m = 0.88 cum
SUB HEAD : 19- DRAINAGE 1897
Code Description Unit Quantity Rate Amount
6.1.1 Rate as per item no 6.1.1 of
SH : Brick Work cum 0.88 6882.00 6056.16 A
12 mm cement plaster 1:3 (1 cement :
3 coarse sand finished with floating
coat of neat cement
Wall : 2.90x1.00 m = 2.90 sqm
13.9.1 Rate as per item no 13.9.1 of
SH : Finishing sqm 2.9 386.55 1121.00 A
TOTAL 7177.16
Cost per metre 7177.16
Say 7177.15
19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey
comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete
as per standard design.
19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Code Description Unit Quantity Rate Amount
Details of cost for one soak pit
Earth work in excavation including
disposal of surplus earth 3.14/
4x(2.5)²x3m = 14.73 cum
2.8.1 Rate as per item no. 2.8.1 of
SH: Earth work cum 14.73 286.85 4225.30 A
2.26.1 Rate as per item no. 2.26.1 of
SH : Earth work cum 7.37 104.50 770.17 A
= 3.14/4x(2.5)² x 1.5 m = 7.37 cum
2nd class bricks
perimetre = 4x0.35 =1.40 m
Area = 1.40x2.925 m = 4.1 sqm
Number of brick = 4.1x487x0.066
= 131.78
Wastage 10% = 13.718
Total= 144.96 Say 145 numbers
2602 Common burnt clay F.P.S. (non
modular) bricks class designation 7.5
1000 Nos 0.145 4590.00 665.55
Brick bats = 3.14/4x(1.2)²x2.925m
=3.33 cum
Deduct = 0.45x0.45x2.925 m
= 0.59 cum
Net qty= 2.74 cum
0362 Brick bats cum 2.74 450.00 1233.00
Brick aggregate 50 to 80 mm nominal
size = 3.14x1.50x0.03x2.925 m = 4.13
cum
0285 Brick Aggregate (Single size) :
63 mm nominal size cum 4.13 650.00 2684.50
Brick aggregate 40 mm nominal size
= 3.14x2.15x0.35x2.925 m =6.91 cum
0287 Brick Aggregate (Single size) :
40 mm nominal size cum 6.91 650.00 4491.50
SUB HEAD : 19- DRAINAGE 1898
Code Description Unit Quantity Rate Amount
1854 Stoneware pipes grade A (60 cm long)
100 mm dia each 3.00 70.00 210.00
Carriage of brick bats and aggregate
2260 Carriage of Brick aggregate cum 13.78 178.19 2455.46
2201 Carriage of Bricks 1000 Nos 0.145 437.15 63.39
9999 Single matting 2.5x2.5 m = 6.25 sqm L.S. 112.14 2.12 237.74
Precast R.C.C.slabs 7.5 cm thick in
cement concrete 1:1.5:3 (1 cement :
1.5 coarse sand : 3 graded stone
aggregate 20 mm nominal size)
0.45x0.45x0.075 m = 0.02 cum
5.12 Rate as per item no 5.12 of SH : RCC cum 0.02 9673.50 193.47 A
Reinforcement @ 80 kg/cum
= 0.02x80 =1.6 kg
5.22.1 Rate as per item no. 5.22.1 of
SH : RCC work kg 1.60 88.95 142.32 A
2nd class brick edging laid length wise
with half brick depth
3.14x2.6 m =8.17 m
16.8.1 Rate as per item no. 16.8.1 of
SH : Road work metre 8.17 49.90 407.68 A
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 3.00 645.00 1935.00
0115 Coolie day 3.00 645.00 1935.00
TOTAL 22399.07 W
Add 1 % Water charges on "W-A" 166.60
TOTAL 22565.67 X
Add GST on "X-A" (multiplying
factor 0.1405) 2364.16
TOTAL 24929.83 Y
Add 15% CPOH on "Y-A" 2878.63
TOTAL 27808.46 Z
Add Cess @ 1% on "Z-A" 220.70
Cost of one soak pit 28029.16
Say 28029.15
19.33 Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain
pipe 100 mm diameter and 1.20 m long complete as per standard design.
Code Description Unit Quantity Rate Amount
Details of cost for one soak pit
Earth work in excavation including
disposal of surplus earth 1.2x1.2x1.2m
= 1.73 cum
2.8.1 (Rate as per item no. 2.8.1 of
SH: Earth work) cum 1.73 286.85 496.25 A
0362 Brick bats cum 1.73 450.00 778.50
1.2x1.2x1.2 = 1.73 cum
2260 Carriage of Brick aggregate cum 1.73 178.19 308.27
SUB HEAD : 19- DRAINAGE 1899
Code Description Unit Quantity Rate Amount
16.8.1 Rate as per item no. 16.8.1 of
SH : Road work metre 5.20 49.90 259.48 A
Second class brick edging laid length
wise with half brick depth
1854 Stoneware pipes grade A (60 cm long)
100 mm dia each 2.00 70.00 140.00
9999 Sundries L.S. 25.84 2.12 54.78
LABOUR
For filling brick bats
0114 Beldar day 0.50 645.00 322.50
9999 Sundries L.S. 13.52 2.12 28.66
TOTAL 2388.44 W
Add 1 % Water charges on "W-A" 16.33
TOTAL 2404.77 X
Add GST on "X-A" (multiplying
factor 0.1405) 231.69
TOTAL 2636.46 Y
Add 15% CPOH on "Y-A" 282.11
TOTAL 2918.57 Z
Add Cess @ 1% on "Z-A" 21.63
Cost of one soak pit 2940.20
Say 2940.20
19.34 Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement
mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
19.34.1 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost of one no.
MATERIAL
7128 S.W. intercepting trap 100 mm dia each 1.00 185.00 185.00
9977 Carriage of trap L.S. 1.04 2.12 2.20
0367 Portland Cement (OPC-43 grade) tonne 0.0013 5000.00 6.50
2209 Carriage of Cement tonne 0.0013 145.72 0.19
0983 Fine sand (zone IV) cum 0.001 900.00 0.90
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.001 163.93 0.16
1881 Spun yarn kilogram 0.09 55.00 4.95
LABOUR
0123 Mason (brick layer) 1st class day 0.02 784.00 15.68
0124 Mason (brick layer) 2nd class day 0.02 714.00 14.28
0114 Beldar day 0.06 645.00 38.70
0101 Bhisti day 0.02 714.00 14.28
TOTAL 282.85 W
Add 1 % Water charges on "W" 2.83
TOTAL 285.68 X
Add GST on "X" (multiplying
factor 0.1405) 40.14
TOTAL 325.81 Y
Add 15% CPOH on "Y" 48.87
TOTAL 374.69 Z
Add Cess @ 1% on "Z" 3.75
Cost of one no. 378.43
Say 378.45
SUB HEAD : 19- DRAINAGE 1900
19.34.2 150 mm dia
Code Description Unit Quantity Rate Amount
Details of cost of one no.
MATERIAL
7129 S.W. intercepting trap 150 mm dia each 1.00 240.00 240.00
9977 Carriage of trap L.S. 2.08 2.12 4.41
0367 Portland Cement (OPC-43 grade) tonne 0.0019 5000.00 9.50
2209 Carriage of Cement tonne 0.0019 145.72 0.28
0983 Fine sand (zone IV) cum 0.0014 900.00 1.26
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.0014 163.93 0.23
1881 Spun yarn kilogram 0.18 55.00 9.90
LABOUR
0123 Mason (brick layer) 1st class day 0.03 784.00 23.52
0124 Mason (brick layer) 2nd class day 0.03 714.00 21.42
0114 Beldar day 0.08 645.00 51.60
0101 Bhisti day 0.03 714.00 21.42
TOTAL 383.54 W
Add 1 % Water charges on “W” 3.84
TOTAL 387.37 X
Add GST on “X” (multiplying
factor 0.1405) 54.43
TOTAL 441.80 Y
Add 15% CPOH on “Y” 66.27
TOTAL 508.07 Z
Add Cess @ 1% on “Z” 5.08
Cost of one no. 513.15
Say 513.15
19.35 Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including
collars/spigot jointed with stiff mixture of cement mortar in the proportion of
1:2 (1 cement : 2 fine sand) including testing of joints etc. complete
19.35.1 450 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1728 RCC pipe 450 mm dia NP-3 spigot metre 10.00 1500.00 15000.00
2299 Carriage of R.C.C. pipes 450 &
500 mm dia 100 metre 0.10 3981.36 398.14
0367 Portland Cement (OPC-43 grade) tonne 0.012 5000.00 60.00
2209 Carriage of Cement tonne 0.012 145.72 1.75
0983 Fine sand (zone IV) cum 0.017 900.00 15.30
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.017 163.93 2.79
LABOUR
0123 Mason (brick layer) 1st class day 0.375 784.00 294.00
0124 Mason (brick layer) 2nd class day 0.375 714.00 267.75
0114 Beldar day 2.41 645.00 1554.45
SUB HEAD : 19- DRAINAGE 1901
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.33 714.00 235.62
TOTAL 17829.79 W
Add 1 % Water charges on "W" 178.30
TOTAL 18008.09 X
Add GST on "X" (multiplying
factor 0.1405) 2530.14
TOTAL 20538.23 Y
Add 15% CPOH on "Y" 3080.73
TOTAL 23618.96 Z
Add Cess @ 1% on "Z" 236.19
Detail of cost for 10 metre 23855.15
Rate per metre 2385.51
Say 2385.50
19.35.2 600 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1729 RCC pipe 600 mm dia NP-3 spigot metre 10.00 2000.00 20000.00
2303 Carriage of R.C.C. pipes 600, 700,
750 & 800 mm dia 100 metre 0.10 5972.04 597.20
0367 Portland Cement (OPC-43 grade) tonne 0.016 5000.00 80.00
2209 Carriage of Cement tonne 0.016 145.72 2.33
0983 Fine sand (zone IV) cum 0.022 900.00 19.80
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.022 163.93 3.61
LABOUR
0123 Mason (brick layer) 1st class day 0.46 784.00 360.64
0124 Mason (brick layer) 2nd class day 0.46 714.00 328.44
0114 Beldar day 1.83 645.00 1180.35
0101 Bhisti day 0.33 714.00 235.62
TOTAL 22807.99 W
Add 1 % Water charges on "W" 228.08
TOTAL 23036.07 X
Add GST on "X" (multiplying
factor 0.1405) 3236.57
TOTAL 26272.64 Y
Add 15% CPOH on "Y" 3940.90
TOTAL 30213.54 Z
Add Cess @ 1% on "Z" 302.14
Detail of cost for 10 metre 30515.67
Rate per metre 3051.57
Say 3051.55
19.35.3 900 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1730 RCC pipe 900 mm dia NP-3 spigot metre 10.00 3175.00 31750.00
2331 Carriage of R.C.C. pipes 900 mm dia 100 metre 0.10 8958.06 895.81
SUB HEAD : 19- DRAINAGE 1902
Code Description Unit Quantity Rate Amount
0367 Portland Cement (OPC-43 grade) tonne 0.025 5000.00 125.00
2209 Carriage of Cement tonne 0.025 145.72 3.64
0983 Fine sand (zone IV) cum 0.033 900.00 29.70
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.033 163.93 5.41
LABOUR
0123 Mason (brick layer) 1st class day 0.625 784.00 490.00
0124 Mason (brick layer) 2nd class day 0.625 714.00 446.25
0114 Beldar day 3.00 645.00 1935.00
0101 Bhisti day 0.50 714.00 357.00
TOTAL 36037.81 W
Add 1 % Water charges on "W" 360.38
TOTAL 36398.19 X
Add GST on "X" (multiplying
factor 0.1405) 5113.95
TOTAL 41512.13 Y
Add 15% CPOH on "Y" 6226.82
TOTAL 47738.95 Z
Add Cess @ 1% on "Z" 477.39
Detail of cost for 10 metre 48216.34
Rate per metre 4821.63
Say 4821.65
19.35.4 1000 mm dia RCC pipes. (Laying by manual/ machanical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1731 RCC pipe 1000 mm dia NP-3 spigot metre 10.00 3915.00 39150.00
2332 Carriage of R.C.C. pipes 1000 mm dia 100 metre 0.10 11944.08 1194.41
0367 Portland Cement (OPC-43 grade) tonne 0.028 5000.00 140.00
2209 Carriage of Cement tonne 0.028 145.72 4.08
0983 Fine sand (zone IV) cum 0.037 900.00 33.30
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.037 163.93 6.07
LABOUR
0123 Mason (brick layer) 1st class day 0.68 784.00 533.12
0124 Mason (brick layer) 2nd class day 0.68 714.00 485.52
0114 Beldar day 4.33 645.00 2792.85
0101 Bhisti day 0.50 714.00 357.00
TOTAL 44696.34 W
Add 1 % Water charges on "W" 446.96
TOTAL 45143.31 X
Add GST on "X" (multiplying
factor 0.1405) 6342.63
TOTAL 51485.94 Y
Add 15% CPOH on "Y" 7722.89
TOTAL 59208.83 Z
Add Cess @ 1% on "Z" 592.09
Detail of cost for 10 metre 59800.92
Rate per metre 5980.09
Say 5980.10
SUB HEAD : 19- DRAINAGE 1903
19.35.5 1200 mm dia RCC pipes. (Laying by manual/ machanical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1732 RCC pipe 1200 mm dia NP-3 spigot metre 10.0 5200.00 52000.00
2334 Carriage of R.C.C. pipes 1200 mm dia 100 metre 0.10 11944.08 1194.41
0367 Portland Cement (OPC-43 grade) tonne 0.034 5000.00 170.00
2209 Carriage of Cement tonne 0.034 145.72 4.95
0983 Fine sand (zone IV) cum 0.046 900.00 41.40
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.046 163.93 7.54
LABOUR
0123 Mason (brick layer) 1st class day 0.795 784.00 623.28
0124 Mason (brick layer) 2nd class day 0.795 714.00 567.63
0114 Beldar day 8.67 645.00 5592.15
0101 Bhisti day 0.67 714.00 478.38
TOTAL 60679.74 W
Add 1 % Water charges on "W" 606.80
TOTAL 61286.54 X
Add GST on "X" (multiplying
factor 0.1405) 8610.76
TOTAL 69897.30 Y
Add 15% CPOH on "Y" 10484.59
TOTAL 80381.89 Z
Add Cess @ 1% on "Z" 803.82
Detail of cost for 10 metre 81185.71
Rate per metre 8118.57
Say 8118.55
19.35.6 1800 mm dia RCC pipes. (Laying by manual/ machenical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1733 RCC pipe 1800 mm dia NP-3 spigot metre 10.00 9450.00 94500.00
2336 Carriage of RCC pipe above 1200 mm
dia and upto 1800 mm dia 100 metre 0.10 11944.08 1194.41
0367 Portland Cement (OPC-43 grade) tonne 0.049 5000.00 245.00
2209 Carriage of Cement tonne 0.049 145.72 7.14
0983 Fine sand (zone IV) cum 0.055 900.00 49.50
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.055 163.93 9.02
LABOUR
0123 Mason (brick layer) 1st class day 1.15 784.00 901.60
0124 Mason (brick layer) 2nd class day 1.15 714.00 821.10
0114 Beldar day 13.00 645.00 8385.00
0101 Bhisti day 1.00 714.00 714.00
TOTAL 106826.76 W
Add 1 % Water charges on "W" 1068.27
TOTAL 107895.03 X
Add GST on "X" (multiplying
factor 0.1405) 15159.25
TOTAL 123054.28 Y
Add 15% CPOH on "Y" 18458.14
TOTAL 141512.43 Z
Add Cess @ 1% on "Z" 1415.12
Detail of cost for 10 metre 142927.55
Rate per metre 14292.76
Say 14292.75
SUB HEAD : 19- DRAINAGE 1904
19.36 Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including
collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of joints etc. complete
19.36.1 450 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1734 RCC pipe 450 mm dia NP-4 spigot metre 10.0 1750.00 17500.00
2299 Carriage of R.C.C. pipes 450 &
500 mm dia 100 metre 0.10 3981.36 398.14
0367 Portland Cement (OPC-43 grade) tonne 0.012 5000.00 60.00
2209 Carriage of Cement tonne 0.012 145.72 1.75
0983 Fine sand (zone IV) cum 0.017 900.00 15.30
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.017 163.93 2.79
LABOUR
0123 Mason (brick layer) 1st class day 0.375 784.00 294.00
0124 Mason (brick layer) 2nd class day 0.375 714.00 267.75
0114 Beldar day 2.41 645.00 1554.45
0101 Bhisti day 0.33 714.00 235.62
TOTAL 20329.79 W
Add 1 % Water charges on "W" 203.30
TOTAL 20533.09 X
Add GST on "X" (multiplying
factor 0.1405) 2884.90
TOTAL 23417.99 Y
Add 15% CPOH on "Y" 3512.70
TOTAL 26930.69 Z
Add Cess @ 1% on "Z" 269.31
Detail of cost for 10 metre 27199.99
Rate per metre 2720.00
Say 2720.00
19.36.2 600 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1735 RCC pipe 600 mm dia pipe NP-4 spigot metre 10.0 2350.00 23500.00
2303 Carriage of R.C.C. pipes 600, 700,
750 & 800 mm dia 100 metre 0.10 5972.04 597.20
0367 Portland Cement (OPC-43 grade) tonne 0.016 5000.00 80.00
2209 Carriage of Cement tonne 0.016 145.72 2.33
0983 Fine sand (zone IV) cum 0.022 900.00 19.80
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.022 163.93 3.61
LABOUR
0123 Mason (brick layer) 1st class day 0.46 784.00 360.64
0124 Mason (brick layer) 2nd class day 0.46 714.00 328.44
0114 Beldar day 1.83 645.00 1180.35
SUB HEAD : 19- DRAINAGE 1905
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.33 714.00 235.62
TOTAL 26307.99 W
Add 1 % Water charges on "W" 263.08
TOTAL 26571.07 X
Add GST on "X" (multiplying
factor 0.1405) 3733.24
TOTAL 30304.31 Y
Add 15% CPOH on "Y" 4545.65
TOTAL 34849.95 Z
Add Cess @ 1% on "Z" 348.50
Detail of cost for 10 metre 35198.45
Rate per metre 3519.85
Say 3519.85
19.36.3 900 mm dia RCC pipes.
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1736 RCC pipe 900 mm dia pipe NP-4 spigot metre 10.0 4500.00 45000.00
2331 R.C.C. pipes 900 mm dia 100 metre 0.10 8958.06 895.81
0367 Portland Cement (OPC-43 grade) tonne 0.025 5000.00 125.00
2209 Carriage of Cement tonne 0.025 145.72 3.64
0983 Fine sand (zone IV) cum 0.033 900.00 29.70
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.033 163.93 5.41
LABOUR
0123 Mason (brick layer) 1st class day 0.625 784.00 490.00
0124 Mason (brick layer) 2nd class day 0.625 714.00 446.25
0114 Beldar day 3.00 645.00 1935.00
0101 Bhisti day 0.5 714.00 357.00
TOTAL 49287.81 W
Add 1 % Water charges on "W" 492.88
TOTAL 49780.69 X
Add GST on "X" (multiplying
factor 0.1405) 6994.19
TOTAL 56774.87 Y
Add 15% CPOH on "Y" 8516.23
TOTAL 65291.10 Z
Add Cess @ 1% on "Z" 652.91
Detail of cost for 10 metre 65944.02
Rate per metre 6594.40
Say 6594.40
19.36.4 1000 mm dia RCC pipes. (Laying by manual/ machanical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1737 RCC pipe 1000 mm dia pipe NP-4 spigot metre 10.0 5570.00 55700.00
2332 Carriage of R.C.C. pipes 1000 mm dia 100 metre 0.10 11944.08 1194.41
SUB HEAD : 19- DRAINAGE 1906
Code Description Unit Quantity Rate Amount
0367 Portland Cement (OPC-43 grade) tonne 0.028 5000.00 140.00
2209 Carriage of Cement tonne 0.028 145.72 4.08
0983 Fine sand (zone IV) cum 0.037 900.00 33.30
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.037 163.93 6.07
LABOUR
0123 Mason (brick layer) 1st class day 0.68 784.00 533.12
0124 Mason (brick layer) 2nd class day 0.68 714.00 485.52
0114 Beldar day 4.33 645.00 2792.85
0101 Bhisti day 0.5 714.00 357.00
TOTAL 61246.34 W
Add 1 % Water charges on "W" 612.46
TOTAL 61858.81 X
Add GST on "X" (multiplying
factor 0.1405) 8691.16
TOTAL 70549.97 Y
Add 15% CPOH on "Y" 10582.50
TOTAL 81132.46 Z
Add Cess @ 1% on "Z" 811.32
Detail of cost for 10 metre 81943.79
Rate per metre 8194.38
Say 8194.40
19.36.5 1200 mm dia RCC pipes. (Laying by manual/ machanical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1738 RCC pipe 1200 mm dia pipe NP-4 spigot metre 10.0 6510.00 65100.00
2334 Carriage of R.C.C. pipes 1200 mm dia 100 metre 0.10 11944.08 1194.41
0367 Portland Cement (OPC-43 grade) tonne 0.034 5000.00 170.00
2209 Carriage of Cement tonne 0.034 145.72 4.95
0983 Fine sand (zone IV) cum 0.046 900.00 41.40
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.046 163.93 7.54
LABOUR
0123 Mason (brick layer) 1st class day 0.795 784.00 623.28
0124 Mason (brick layer) 2nd class day 0.795 714.00 567.63
0114 Beldar day 8.67 645.00 5592.15
0101 Bhisti day 0.67 714.00 478.38
TOTAL 73779.74 W
Add 1 % Water charges on "W" 737.80
TOTAL 74517.54 X
Add GST on "X" (multiplying
factor 0.1405) 10469.71
TOTAL 84987.26 Y
Add 15% CPOH on "Y" 12748.09
TOTAL 97735.34 Z
Add Cess @ 1% on "Z" 977.35
Detail of cost for 10 metre 98712.70
Rate per metre 9871.27
Say 9871.25
SUB HEAD : 19- DRAINAGE 1907
19.36.6 1800 mm dia RCC pipes. (Laying by manual/ machanical means)
Code Description Unit Quantity Rate Amount
Detail for 10 metre
MATERIALS :
1739 RCC pipe 1800 mm dia pipe NP-4 spigot metre 10.0 13650.00 136500.00
2336 RCC pipe above 1200 mm dia and upto
1800 mm dia 100 metre 0.10 11944.08 1194.41
0367 Portland Cement (OPC-43 grade) tonne 0.049 5000.00 245.00
2209 Carriage of Cement tonne 0.049 145.72 7.14
0983 Fine sand (zone IV) cum 0.055 900.00 49.50
2261 Carriage of Fine sand (1 part badarpur
sand : 2 parts jamuna sand) cum 0.055 163.93 9.02
LABOUR
0123 Mason (brick layer) 1st class day 1.15 784.00 901.60
0124 Mason (brick layer) 2nd class day 1.15 714.00 821.10
0114 Beldar day 13.00 645.00 8385.00
0101 Bhisti day 1.00 714.00 714.00
TOTAL 148826.76 W
Add 1 % Water charges on "W" 1488.27
TOTAL 150315.03 X
Add GST on "X" (multiplying
factor 0.1405) 21119.26
TOTAL 171434.29 Y
Add 15% CPOH on "Y" 25715.14
TOTAL 197149.44 Z
Add Cess @ 1% on "Z" 1971.49
Detail of cost for 10 metre 199120.93
Rate per metre 19912.09
Say 19912.10
SUB HEAD : 19- DRAINAGE 1908
SUB HEAD : 20.0
PILE WORK
1909
20.1 Providing, driving with hydraulic piling rigs with power units and installing
driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified
diameter and length below the pile cap, to carry safe working load not less
than specified, excluding the cost of steel reinforcement but including the
cost of shoe and the length of pile to be embedded in the pile cap etc. all
complete. (Length of pile for payment shall be measured from top of shoe to
the bottom of pile cap) :
20.1.1 400 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x0.40²x20 = 2.51 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 2.51 7997.30 20073.22 A
9999 Sundries L.S. 175.00 2.12 371.00
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg per
pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.36 35000.00 12600.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 39951.94 W
Add 1 % Water charges on "W-A" 198.79
TOTAL 40150.73 X
Add GST on "X-A" (multiplying
factor 0.1405) 2820.89
TOTAL 42971.62 Y
Add 15% CPOH on "Y-A" 3434.76
TOTAL 46406.38 Z
Add Cess @ 1% on "Z-A" 263.33
Cost of 20 metre pile 46669.71
Cost of 1 metre pile 2333.49
Say 2333.50
20.1.2 450 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x0.45²x20 = 3.18 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.18 7997.30 25431.41 A
9999 Sundries L.S. 225.00 2.12 477.00
SUB HEAD : 20- PILE WORK 1911
Code Description Unit Quantity Rate Amount
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg per
pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.48 35000.00 16800.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 49616.13 W
Add 1 % Water charges on "W-A" 241.85
TOTAL 49857.98 X
Add GST on "X-A" (multiplying
factor 0.1405) 3431.93
TOTAL 53289.91 Y
Add 15% CPOH on "Y-A" 4178.77
TOTAL 57468.69 Z
Add Cess @ 1% on "Z-A" 320.37
Cost of 20 metre pile 57789.06
Cost of 1 metre pile 2889.45
Say 2889.45
20.1.3 500 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.50²x20 = 3.925 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.925 7997.30 31389.40 A
9999 Sundries L.S. 275.00 2.12 583.00
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.60 35000.00 21000.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
SUB HEAD : 20- PILE WORK 1912
Code Description Unit Quantity Rate Amount
0114 Beldar day 2.00 645.00 1290.00
TOTAL 59880.12 W
Add 1 % Water charges on "W-A" 284.91
TOTAL 60165.03 X
Add GST on "X-A" (multiplying
factor 0.1405) 4042.98
TOTAL 64208.01 Y
Add 15% CPOH on "Y-A" 4922.79
TOTAL 69130.80 Z
Add Cess @ 1% on "Z-A" 377.41
Cost of 20 metre pile 69508.21
Cost of 1 metre pile 3475.41
Say 3475.40
20.1.4 550 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.55²x20 = 4.75 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 4.75 7997.30 37987.18 A
9999 Sundries L.S. 330.00 2.12 699.60
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.60 35000.00 21000.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 66594.50 W
Add 1 % Water charges on "W-A" 286.07
TOTAL 66880.57 X
Add GST on "X-A" (multiplying
factor 0.1405) 4059.52
TOTAL 70940.09 Y
Add 15% CPOH on "Y-A" 4942.94
TOTAL 75883.03 Z
Add Cess @ 1% on "Z-A" 378.96
Cost of 20 metre pile 76261.99
Cost of 1 metre pile 3813.10
Say 3813.10
SUB HEAD : 20- PILE WORK 1913
20.1.5 750 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 15 m length of pile
MATERIAL
Concrete 3.14/4x0.75²x15 = 6.62 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 6.62 7997.30 52942.13 A
9999 Sundries L.S. 460.00 2.12 975.20
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.70 35000.00 24500.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.14 784.00 109.76
0114 Beldar day 3.50 645.00 2257.50
TOTAL 86339.59 W
Add 1 % Water charges on "W-A" 333.97
TOTAL 86673.56 X
Add GST on "X-A" (multiplying
factor 0.1405) 4739.27
TOTAL 91412.83 Y
Add 15% CPOH on "Y-A" 5770.61
TOTAL 97183.43 Z
Add Cess @ 1% on "Z-A" 442.41
Cost of 15 metre pile 97625.85
Cost of 1 metre pile 6508.39
Say 6508.40
20.1.6 1000 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 m length of pile
MATERIAL
Concrete 3.14/4x1.00²x10 = 7.85 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 7.85 7997.30 62778.81 A
9999 Sundries L.S. 550.00 2.12 1166.00
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
SUB HEAD : 20- PILE WORK 1914
Code Description Unit Quantity Rate Amount
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.68 35000.00 23800.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.16 784.00 125.44
0114 Beldar day 4.00 645.00 2580.00
TOTAL 96005.25 W
Add 1 % Water charges on "W-A" 332.26
TOTAL 96337.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 4715.00
TOTAL 101052.51 Y
Add 15% CPOH on "Y-A" 5741.06
TOTAL 106793.56 Z
Add Cess @ 1% on "Z-A" 440.15
Cost of 10 metre pile 107233.71
Cost of 1 metre pile 10723.37
Say 10723.35
20.1.7 1200 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 9 m length of pile
MATERIAL
Concrete 3.14/4x1.2²x9 = 10.17 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 10.17 7997.30 81332.54 A
9999 Sundries L.S. 710.00 2.12 1505.20
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.67 35000.00 23450.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
LABOUR
Work supervisor
0130 Mistry day 0.18 784.00 141.12
SUB HEAD : 20- PILE WORK 1915
Code Description Unit Quantity Rate Amount
0114 Beldar day 4.50 645.00 2902.50
TOTAL 114886.36 W
Add 1 % Water charges on "W-A" 335.54
TOTAL 115221.90 X
Add GST on "X-A" (multiplying
factor 0.1405) 4761.45
TOTAL 119983.35 Y
Add 15% CPOH on "Y-A" 5797.62
TOTAL 125780.98 Z
Add Cess @ 1% on "Z-A" 444.48
Cost of 9 metre pile 126225.46
Cost of 1 metre pile 14025.05
Say 14025.05
20.1.8 1500 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 9 m length of pile
MATERIAL
Concrete 3.14/4x1.5²x9 = 15.90 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 15.90 7997.30 127157.07 A
9999 Sundries L.S. 1115.00 2.12 2363.80
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of
35 kg per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.77 35000.00 26950.00
0025 Hire and running charges of light crane. day 0.10 3500.00 350.00
LABOUR
Work supervisor
0130 Mistry day 0.20 784.00 156.80
0114 Beldar day 5.00 645.00 3225.00
TOTAL 165547.67 W
Add 1 % Water charges on "W-A" 383.91
TOTAL 165931.58 X
Add GST on "X-A" (multiplying
factor 0.1405) 5447.82
TOTAL 171379.39 Y
Add 15% CPOH on "Y-A" 6633.35
TOTAL 178012.74 Z
Add Cess @ 1% on "Z-A" 508.56
Cost of 9 metre pile 178521.30
Cost of 1 metre pile 19835.70
Say 19835.70
SUB HEAD : 20- PILE WORK 1916
20.2 Boring, providing and installation bored cast-in-situ reinforced cement concrete
piles of grade M-25 of specified diameter and length below the pile cap, to carry
a safe working load not less than specified, excluding the cost of steel
reinforcement but including the cost of boring with bentonite solution and
temporary casing of appropriate length for setting out and removal of same
and the length of the pile to be embedded in the pile cap etc. by percussion
drilling using Direct mud circulation (DMC) or Bailer and chisel technique by
tripod and mechanical Winch Machine all complete, including removal of
excavated earth with all its lifts and leads (length of pile for payment shall be
measured up to bottom of pile cap).
Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used .
20.2.1 450 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.45²x20 = 3.18 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.18 7997.30 25431.41 A
7183 Bentonite tonne 0.25 2800.00 700.00
9999 Sundries L.S. 65.00 2.12 137.80
MACHINERY
0015 Hire and running charges of Tripod and
Mechanical Winch machine complete
with power unit and accessories day 0.94 3000.00 2820.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.38 3000.00 1140.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 2.50 645.00 1612.50
TOTAL 35070.79 W
Add 1 % Water charges on "W-A" 96.39
TOTAL 35167.19 X
Add GST on "X-A" (multiplying
factor 0.1405) 1367.88
TOTAL 36535.06 Y
Add 15% CPOH on "Y-A" 1665.55
TOTAL 38200.61 Z
Add Cess @ 1% on "Z-A" 127.69
Cost of 20 metre pile 38328.30
Cost of 1 metre pile 1916.42
Say 1916.40
20.2.2 500 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.50²x20 = 3.925cum
SUB HEAD : 20- PILE WORK 1917
Code Description Unit Quantity Rate Amount
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.925 7997.30 31389.40 A
7183 Bentonite tonne 0.28 2800.00 784.00
9999 Sundries L.S. 80.00 2.12 169.60
MACHINERY
0015 Hire and running charges of Tripod and
Mechanical Winch machine complete
with power unit and accessories day 1.20 3000.00 3600.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.38 3000.00 1140.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 2.50 645.00 1612.50
TOTAL 41924.58 W
Add 1 % Water charges on "W-A" 105.35
TOTAL 42029.93 X
Add GST on "X-A" (multiplying
factor 0.1405) 1494.99
TOTAL 43524.93 Y
Add 15% CPOH on "Y-A" 1820.33
TOTAL 45345.26 Z
Add Cess @ 1% on "Z-A" 139.56
Cost of 20 metre pile 45484.82
Cost of 1 metre pile 2274.24
Say 2274.25
20.2.3 600 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.60²x20 = 5.65 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 5.65 7997.30 45184.75 A
7183 Bentonite tonne 0.33 2800.00 924.00
9999 Sundries L.S. 115.00 2.12 243.80
MACHINERY
0015 Hire and running charges of Tripod and
Mechanical Winch machine complete
with power unit and accessories day 1.50 3000.00 4500.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.38 3000.00 1140.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
SUB HEAD : 20- PILE WORK 1918
Code Description Unit Quantity Rate Amount
0114 Beldar day 3.00 645.00 1935.00
TOTAL 57156.63 W
Add 1 % Water charges on "W-A" 119.72
TOTAL 57276.34 X
Add GST on "X-A" (multiplying
factor 0.1405) 1698.87
TOTAL 58975.21 Y
Add 15% CPOH on "Y-A" 2068.57
TOTAL 61043.78 Z
Add Cess @ 1% on "Z-A" 158.59
Cost of 20 metre pile 61202.37
Cost of 1 metre pile 3060.12
Say 3060.10
20.2.4 750 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 15 m length of pile
MATERIAL
Concrete 3.14/4x0.75²x15 = 6.62 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 6.62 7997.30 52942.13 A
7183 Bentonite tonne 0.30 2800.00 840.00
9999 Sundries L.S. 130.00 2.12 275.60
MACHINERY
0015 Hire and running charges of Tripod and
Mechanical Winch machine complete
with power unit and accessories day 1.40 3000.00 4200.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.75 3000.00 2250.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
LABOUR
Work supervisor
0130 Mistry day 0.14 784.00 109.76
0114 Beldar day 3.50 645.00 2257.50
TOTAL 66009.99 W
Add 1 % Water charges on "W-A" 130.68
TOTAL 66140.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 1854.39
TOTAL 67995.06 Y
Add 15% CPOH on "Y-A" 2257.94
TOTAL 70253.00 Z
Add Cess @ 1% on "Z-A" 173.11
Cost of 15 metre pile 70426.11
Cost of 1 metre pile 4695.07
Say 4695.05
SUB HEAD : 20- PILE WORK 1919
20.2A Boring, providing and installation bored cast-in-situ reinforced cement concrete
piles of garde M-25 of specified diameter and length below pile cap, to carry a
safe working load not less than specified, excluding the cost of steel
reinforcement but including the cost of boring with bentonite solution and
temporary casing of appropriate length for setting out and removal of same
and the length of the pile to be embedded in the pile cap etc. by Crawler mounted,
telescopic boom hydraulic pilling Rig all complete, including removal of
excavated earth with all its lifts and leads (length of pile for payment shall be
measured up to bottom of pile cap).
Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.
20.2A.1 600 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete 3.14/4x0.60²x20 = 5.65 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 5.65 7997.30 45184.75 A
7183 Bentonite tonne 0.33 2800.00 924.00
9999 Sundries L.S. 110.00 2.12 233.20
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.75 35000.00 26250.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.38 3000.00 1140.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 78896.03 W
Add 1 % Water charges on "W-A" 337.11
TOTAL 79233.14 X
Add GST on "X-A" (multiplying
factor 0.1405) 4783.80
TOTAL 84016.94 Y
Add 15% CPOH on "Y-A" 5824.83
TOTAL 89841.77 Z
Add Cess @ 1% on "Z-A" 446.57
Cost of 20 metre pile 90288.34
Cost of 1 metre pile 4514.42
Say 4514.40
20.2A.2 750 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 15 m length of pile
MATERIAL
Concrete 3.14/4x0.75²x15 = 6.62 cum
SUB HEAD : 20- PILE WORK 1920
Code Description Unit Quantity Rate Amount
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 6.62 7997.30 52942.13 A
7183 Bentonite tonne 0.30 2800.00 840.00
9999 Sundries L.S. 130.00 2.12 275.60
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.70 35000.00 24500.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.75 3000.00 2250.00
0018 Hire and running charges of loader day 0.30 6000.00 1800.00
0017 Hire and running charges of tipper day 0.30 3750.00 1125.00
LABOUR
Work supervisor
0130 Mistry day 0.14 784.00 109.76
0114 Beldar day 3.50 645.00 2257.50
TOTAL 86309.99 W
Add 1 % Water charges on "W-A" 333.68
TOTAL 86643.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 4735.07
TOTAL 91378.73 Y
Add 15% CPOH on "Y-A" 5765.49
TOTAL 97144.22 Z
Add Cess @ 1% on "Z-A" 442.02
Cost of 15 metre pile 97586.24
Cost of 1 metre pile 6505.75
Say 6505.75
20.2A.3 1000 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 m length of pile
MATERIAL
Concrete 3.14/4x1.00²x10 = 7.85 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 7.85 7997.30 62778.81 A
7183 Bentonite tonne 0.35 2800.00 980.00
9999 Sundries L.S. 155.00 2.12 328.60
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.69 35000.00 24150.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.75 3000.00 2250.00
0018 Hire and running charges of loader day 0.40 6000.00 2400.00
0017 Hire and running charges of tipper day 0.40 3750.00 1500.00
SUB HEAD : 20- PILE WORK 1921
Code Description Unit Quantity Rate Amount
LABOUR
Work supervisor
0130 Mistry day 0.16 784.00 125.44
0114 Beldar day 4.00 645.00 2580.00
TOTAL 97302.85 W
Add 1 % Water charges on "W-A" 345.24
TOTAL 97648.09 X
Add GST on "X-A" (multiplying
factor 0.1405) 4899.13
TOTAL 102547.22 Y
Add 15% CPOH on "Y-A" 5965.26
TOTAL 108512.48 Z
Add Cess @ 1% on "Z-A" 457.34
Cost of 10 metre pile 108969.82
Cost of 1 metre pile 10896.98
Say 10897.00
20.2A.4 1200 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 9 m length of pile
MATERIAL
Concrete 3.14/4x1.20²x9 = 10.17 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 10.17 7997.30 81332.54 A
7183 Bentonite tonne 0.385 2800.00 1078.00
9999 Sundries L.S. 200.00 2.12 424.00
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.67 35000.00 23450.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.75 3000.00 2250.00
0018 Hire and running charges of loader. day 0.50 6000.00 3000.00
0017 Hire and running charges of tipper day 0.50 3750.00 1875.00
LABOUR
Work supervisor
0130 Mistry day 0.18 784.00 141.12
0114 Beldar day 4.50 645.00 2902.50
TOTAL 116663.16 W
Add 1 % Water charges on "W-A" 353.31
TOTAL 117016.47 X
Add GST on "X-A" (multiplying
factor 0.1405) 5013.59
TOTAL 122030.06 Y
Add 15% CPOH on "Y-A" 6104.63
TOTAL 128134.69 Z
Add Cess @ 1% on "Z-A" 468.02
Cost of 9 metre pile 128602.71
Cost of 1 metre pile 14289.19
Say 14289.20
SUB HEAD : 20- PILE WORK 1922
20.2A.5 1500 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 9 m length of pile
MATERIAL
Concrete 3.14/4x1.50²x9 = 15.90 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 15.90 7997.30 127157.07 A
7183 Bentonite tonne 0.45 2800.00 1260.00
9999 Sundries L.S. 315.00 2.12 667.80
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.77 35000.00 26950.00
0025 Hire and running charges of light crane. day 0.10 3500.00 350.00
0026 Hire and running charges of bentonite
pump. day 0.96 3000.00 2880.00
0018 Hire and running charges of loader day 0.75 6000.00 4500.00
0017 Hire and running charges of tipper day 0.75 3750.00 2812.50
LABOUR
Work supervisor
0130 Mistry day 0.25 784.00 196.00
0114 Beldar day 5.00 645.00 3225.00
TOTAL 169998.37 W
Add 1 % Water charges on "W-A" 428.41
TOTAL 170426.78 X
Add GST on "X-A" (multiplying
factor 0.1405) 6079.39
TOTAL 176506.18 Y
Add 15% CPOH on "Y-A" 7402.37
TOTAL 183908.54 Z
Add Cess @ 1% on "Z-A" 567.51
Cost of 9 metre pile 184476.06
Cost of 1 metre pile 20497.34
Say 20497.35
20.3 Boring with hydraulic piling rigs with power units, providing and installing cast
in situ single under reamed piles of specified diameter and length below pile
cap in M-25 cement concrete, to carry a safe working load not less than specified,
excluding the cost of steel reinforcement but including the cost of boring with
bentonite solution and the length of the pile to be embedded in pile cap etc. all
complete. (Length of pile for payment shall be measured upto to the bottom of
pile cap) :
20.3.1 300 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
R.C.C
Stem -3.14/4x(0.30)²x9.625 = 0.680 cum
Bulb -3.14/4x(0.75)²x0.075 = 0.033 cum
2x 3.14/4x(0.525)²x0.150 = 0.065 cum
=0.778 cum
SUB HEAD : 20- PILE WORK 1923
Code Description Unit Quantity Rate Amount
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 0.778 7997.30 6221.90 A
7183 Bentonite tonne 0.08 2800.00 224.00
9999 Sundries L.S. 70.00 2.12 148.40
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.36 35000.00 12600.00
0025 Hire and running charges of light crane. day 0.03 3500.00 105.00
0026 Hire and running charges of bentonite
pump. day 0.02 3000.00 60.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 20712.02 W
Add 1 % Water charges on "W-A" 144.90
TOTAL 20856.92 X
Add GST on "X-A" (multiplying
factor 0.1405) 2056.22
TOTAL 22913.14 Y
Add 15% CPOH on "Y-A" 2503.69
TOTAL 25416.83 Z
Add Cess @ 1% on "Z-A" 191.95
Cost of 10 metre pile 25608.78
Cost of 1 metre pile 2560.88
Say 2560.90
20.3.2 400 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
R.C.C
Stem -3.14/4x(0.40)²x9.30 = 1.169 cum
Bulb -3.14/4x(1.00)²x0.1 = 0.079 cum
2x 3.14/4x(0.7)²x0.30 = 0.23 cum
= 1.478 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 1.478 7997.30 11820.01 A
7183 Bentonite tonne 0.15 2800.00 420.00
9999 Sundries L.S. 130.00 2.12 275.60
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.36 35000.00 12600.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.02 3000.00 60.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
SUB HEAD : 20- PILE WORK 1924
Code Description Unit Quantity Rate Amount
0114 Beldar day 2.00 645.00 1290.00
TOTAL 26738.33 W
Add 1 % Water charges on "W-A" 149.18
TOTAL 26887.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 2116.98
TOTAL 29004.50 Y
Add 15% CPOH on "Y-A" 2577.67
TOTAL 31582.17 Z
Add Cess @ 1% on "Z-A" 197.62
Cost of 10 metre pile 31779.79
Cost of 1 metre pile 3177.98
Say 3178.00
20.3.3 450 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
R.C.C
Stem -3.14/4x(0.45)²x9.212 = 1.465 cum
Bulb -3.14/4x(1.125)²x0.113 = 0.112 cum
2x 3.14/4x(0.788)²x0.337 = 0.329 cum
= 1.906 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 1.906 7997.30 15242.85 A
7183 Bentonite tonne 0.19 2800.00 532.00
9999 Sundries L.S. 165.00 2.12 349.80
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.36 35000.00 12600.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.02 3000.00 60.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 30347.37 W
Add 1 % Water charges on "W-A" 151.05
TOTAL 30498.42 X
Add GST on "X-A" (multiplying
factor 0.1405) 2143.41
TOTAL 32641.83 Y
Add 15% CPOH on "Y-A" 2609.85
TOTAL 35251.67 Z
Add Cess @ 1% on "Z-A" 200.09
Cost of 10 metre pile 35451.76
Cost of 1 metre pile 3545.18
Say 3545.20
SUB HEAD : 20- PILE WORK 1925
20.3.4 550 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 10 metres
MATERIAL
R.C.C
Stem -3.14/4x(0.50)²x9.125 = 1.792 cum
Bulb -3.14/4x(1.25)²x0.125 = 0.153 cum
2x 3.14/4x(0.875)²x0.375 = 0.451 cum
= 2.396 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 2.40 7997.30 19193.52 A
7183 Bentonite tonne 0.20 2800.00 560.00
9999 Sundries L.S. 210.00 2.12 445.20
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.36 35000.00 12600.00
0025 Hire and running charges of light crane. day 0.06 3500.00 210.00
0026 Hire and running charges of bentonite
pump. day 0.02 3000.00 60.00
LABOUR
Work supervisor
0130 Mistry day 0.08 784.00 62.72
0114 Beldar day 2.00 645.00 1290.00
TOTAL 34421.44 W
Add 1 % Water charges on "W-A" 152.28
TOTAL 34573.72 X
Add GST on "X-A" (multiplying
factor 0.1405) 2160.92
TOTAL 36734.64 Y
Add 15% CPOH on "Y-A" 2631.17
TOTAL 39365.80 Z
Add Cess @ 1% on "Z-A" 201.72
Cost of 10 metre pile 39567.53
Cost of 1 metre pile 3956.75
Say 3956.75
20.4 Extra over single under ream for providing additional bulbs in under reamed
piles, under specified diameter(only the nos. of extra bulbs are to be paid)
20.4.1 300 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 1 bulb.
MATERIAL
Bulb - 0.033 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 0.033 7997.30 263.91 A
7183 Bentonite tonne 0.003 2800.00 8.40
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.02 35000.00 700.00
SUB HEAD : 20- PILE WORK 1926
Code Description Unit Quantity Rate Amount
0025 Hire and running charges of light crane. day 0.01 3500.00 35.00
0026 Hire and running charges of bentonite
pump. day 0.01 3000.00 30.00
LABOUR
Work supervisor
0130 Mistry day 0.02 784.00 15.68
0114 Beldar day 1.00 645.00 645.00
TOTAL 1697.99 W
Add 1 % Water charges on "W-A" 14.34
TOTAL 1712.33 X
Add GST on "X-A" (multiplying
factor 0.1405) 203.50
TOTAL 1915.83 Y
Add 15% CPOH on "Y-A" 247.79
TOTAL 2163.62 Z
Add Cess @ 1% on "Z-A" 19.00
Cost of 1 bulb 2182.62
Say 2182.60
20.4.2 400 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 1 bulb.
MATERIAL
Bulb - 0.063 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 0.063 7997.30 503.83 A
7183 Bentonite tonne 0.006 2800.00 16.80
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.02 35000.00 700.00
0025 Hire and running charges of light crane. day 0.01 3500.00 35.00
0026 Hire and running charges of bentonite
pump. day 0.01 3000.00 30.00
LABOUR
Work supervisor
0130 Mistry day 0.02 784.00 15.68
0114 Beldar day 1.00 645.00 645.00
TOTAL 1946.31 W
Add 1 % Water charges on "W-A" 14.42
TOTAL 1960.73 X
Add GST on "X-A" (multiplying
factor 0.1405) 204.70
TOTAL 2165.43 Y
Add 15% CPOH on "Y-A" 249.24
TOTAL 2414.67 Z
Add Cess @ 1% on "Z-A" 19.11
Cost of 1 bulb 2433.78
Say 2433.80
SUB HEAD : 20- PILE WORK 1927
20.4.3 450 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 1 bulb.
MATERIAL
Bulb - 0.081 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 0.081 7997.30 647.78 A
7183 Bentonite tonne 0.008 2800.00 22.40
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.02 35000.00 700.00
0025 Hire and running charges of light crane. day 0.01 3500.00 35.00
0026 Hire and running charges of bentonite
pump. day 0.01 3000.00 30.00
LABOUR
Work supervisor
0130 Mistry day 0.02 784.00 15.68
0114 Beldar day 1.00 645.00 645.00
TOTAL 2095.86 W
Add 1 % Water charges on "W-A" 14.48
TOTAL 2110.34 X
Add GST on "X-A" (multiplying
factor 0.1405) 205.49
TOTAL 2315.83 Y
Add 15% CPOH on "Y-A" 250.21
TOTAL 2566.04 Z
Add Cess @ 1% on "Z-A" 19.18
Cost of 1 bulb 2585.22
Say 2585.20
20.4.4 550 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 1 bulb.
MATERIAL
Bulb - 0.102 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 0.102 7997.30 815.72 A
7183 Bentonite tonne 0.01 2800.00 28.00
MACHINERY
0024 Hire and running charges of hydraulic
piling rig with power unit etc. including
complete accessories and shifting at
site. day 0.02 35000.00 700.00
0025 Hire and running charges of light crane. day 0.01 3500.00 35.00
0026 Hire and running charges of bentonite
pump. day 0.02 3000.00 60.00
LABOUR
Work supervisor
0130 Mistry day 0.02 784.00 15.68
SUB HEAD : 20- PILE WORK 1928
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.00 645.00 645.00
TOTAL 2299.40 W
Add 1 % Water charges on "W-A" 14.84
TOTAL 2314.24 X
Add GST on "X-A" (multiplying
factor 0.1405) 210.54
TOTAL 2524.78 Y
Add 15% CPOH on "Y-A" 256.36
TOTAL 2781.14 Z
Add Cess @ 1% on "Z-A" 19.65
Cost of 1 bulb 2800.80
Say 2800.80
20.5 Providing, driving (with vibrating pile driving hammer complete with power units
& accessories) and installing driven Pre-cast reinforced cement concrete piles
of specified diameter and length below the pile cap in M-25 cement concrete to
carry safe working load not less than specified with a central through preformed
hole with M.S. black pipe of dia, 40 mm for grouting with cement sand grouting
of mix 1:2 (1cement : 2 coarse sand) under sufficient positive pressure to ensure
complete filling including centring, shuttering, driving and removing the steel
casing pipe and lifting casing etc. complete but excluding the cost of steel
reinforcement. (Length of pile for payment shall be measured from top of the
shoe to the bottom of pile cap).
20.5.1 400 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(0.40)²x20 = 2.51 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 2.51 7997.30 20073.22 A
5.19 Add Rate as per item no 5.19 of
SH : RCC cum 2.51 14191.95 35621.79 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -2.51 7945.65 -19943.58 A
Cement mortar 1:2 for grout
3.7 Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block for 2 pile L.S. 442.00 2.12 937.04
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg
per pile kilogram 35.00 43.00 1505.00
@35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
SUB HEAD : 20- PILE WORK 1929
Code Description Unit Quantity Rate Amount
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 56025.04 W
Add 1 % Water charges on "W-A" 202.74
TOTAL 56227.77 X
Add GST on "X-A" (multiplying
factor 0.1405) 2876.93
TOTAL 59104.70 Y
Add 15% CPOH on "Y-A" 3502.99
TOTAL 62607.69 Z
Add Cess @ 1% on "Z-A" 268.56
Cost of 20 metre pile 62876.25
Cost of 1 metre pile 3143.81
Say 3143.80
20.5.2 450 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(0.45)²x20 = 3.18 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.18 7997.30 25431.41 A
5.19 Add Rate as per item no 5.19 SH : RCC cum 3.18 14191.95 45130.40 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -3.18 7945.65 -25267.17 A
Cement mortar 1:2 for grout
3.7 Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block per two piles L.S. 442.00 2.12 937.04
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg kilogram 35.00 43.00 1505.00
per pile @ 35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
LABOUR
Work supervisor
0130 Mistry day 1.08 784.00 846.72
SUB HEAD : 20- PILE WORK 1930
Code Description Unit Quantity Rate Amount
0114 Beldar day 10.78 645.00 6953.10
TOTAL 71338.99 W
Add 1 % Water charges on "W-A" 260.44
TOTAL 71599.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 3695.82
TOTAL 75295.25 Y
Add 15% CPOH on "Y-A" 4500.09
TOTAL 79795.35 Z
Add Cess @ 1% on "Z-A" 345.01
Cost of 20 metre pile 80140.35
Cost of 1 metre pile 4007.02
Say 4007.00
20.5.3 500 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(0.50)²x20 = 3.925 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 3.925 7997.30 31389.40 A
5.19 Add Rate as per item no 5.19 SH : RCC cum 3.925 14191.95 55703.40 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -3.925 7945.65 -31186.68 A
3.7 Cement mortar 1:2 for grout
Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block per two piles L.S. 442.00 2.12 937.04
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 76179.73 W
Add 1 % Water charges on "W-A" 202.74
TOTAL 76382.47 X
Add GST on "X-A" (multiplying
factor 0.1405) 2876.93
TOTAL 79259.39 Y
Add 15% CPOH on "Y-A" 3502.99
TOTAL 82762.38 Z
Add Cess @ 1% on "Z-A" 268.56
Cost of 20 metre pile 83030.94
Cost of 1 metre pile 4151.55
Say 4151.55
SUB HEAD : 20- PILE WORK 1931
20.5.4 550 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(0.55)²x20 = 4.75 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 4.75 7997.30 37987.18 A
5.19 Add Rate as per item no 5.19 SH : RCC cum 4.75 14191.95 67411.76 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -4.75 7945.65 -37741.84 A
3.7 Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block per two piles L.S. 442.00 2.12 937.04
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 87930.70 W
Add 1 % Water charges on "W-A" 202.74
TOTAL 88133.44 X
Add GST on "X-A" (multiplying
factor 0.1405) 2876.93
TOTAL 91010.36 Y
Add 15% CPOH on "Y-A" 3502.99
TOTAL 94513.35 Z
Add Cess @ 1% on "Z-A" 268.56
Cost of 20 metre pile 94781.91
Cost of 1 metre pile 4739.10
Say 4739.10
20.5.5 750 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(0.75)²x20 = 10.88 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 10.88 7997.30 87010.62 A
5.19 Add Rate as per item no 5.19 SH : RCC cum 10.88 14191.95 154408.42 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -10.88 7945.65 -86448.67 A
3.7 Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block per two piles L.S. 442.00 2.12 937.04
SUB HEAD : 20- PILE WORK 1932
Code Description Unit Quantity Rate Amount
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg
per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 175243.97 W
Add 1 % Water charges on "W-A" 202.74
TOTAL 175446.71 X
Add GST on "X-A" (multiplying
factor 0.1405) 2876.93
TOTAL 178323.63 Y
Add 15% CPOH on "Y-A" 3502.99
TOTAL 181826.62 Z
Add Cess @ 1% on "Z-A" 268.56
Cost of 20 metre pile 182095.18
Cost of 1 metre pile 9104.76
Say 9104.75
20.5.6 1000 mm dia piles
Code Description Unit Quantity Rate Amount
Details of cost for 20 m length of pile
MATERIAL
Concrete -3.14/4x(1.00)²x20 = 15.70 cum
5.33.1.1 Rate as per item no 5.33.1.1 of
SH : RCC Work cum 15.7 7997.30 125557.61 A
5.19 Add Rate as per item no 5.19 SH : RCC cum 15.7 14191.95 222813.62 A
5.1.3 Deduct Rate as per item no 5.1.3
SH : RCC cum -15.7 7945.65 -124746.71 A
3.7 Rate as per Item Number 3.7 of
SH: Mortars cum 0.025 5699.25 142.48
9999 Wooden block @ 1 block per two piles L.S. 442.00 2.12 937.04
7181 C.I. pile shoe of 80 kg per pile kilogram 80.00 48.00 3840.00
@ 80 kg per pile
7182 M.S. clamps for pile shoe of 35 kg
per pile kilogram 35.00 43.00 1505.00
@ 35 kg per pile
MACHINERY
0027 Hire and running charges of vibrating
pile driving hammer complete with
power unit and accessories . day 0.38 30000.00 11400.00
0028 Hire and running charges of crane
20 tonne capacity. day 0.06 7000.00 420.00
SUB HEAD : 20- PILE WORK 1933
Code Description Unit Quantity Rate Amount
LABOUR
Work supervisor
0130 Mistry day 0.12 784.00 94.08
0114 Beldar day 3.00 645.00 1935.00
TOTAL 243898.12 W
Add 1 % Water charges on "W-A" 202.74
TOTAL 244100.86 X
Add GST on "X-A" (multiplying
factor 0.1405) 2876.93
TOTAL 246977.78 Y
Add 15% CPOH on "Y-A" 3502.99
TOTAL 250480.77 Z
Add Cess @ 1% on "Z-A" 268.56
Cost of 20 metre pile 250749.33
Cost of 1 metre pile 12537.47
Say 12537.45
20.6 Vertical load testing of piles in accordance with IS 2911 (Part IV) including
installation of loading platform by Kentledge/Anchor piles method and
preparation of pile head or construction of test cap and dismantling of test cap
after test etc. complete as per specification & the direction of Engineer in-charge.
20.6.1 Single pile upto 50 tonne Safe capacity
20.6.1.1 Initial test (Test Load 2.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7246 Verticle load testing (INITIAL) of piles
in accordance with IS : 2911 (Part-IV)
including installation of loading platform
and prepration of pile head or
construction of test cap and
dismantling of test cap after test etc.
complete as per specification and upto
50MT capacity pile. per test 1.00 38500.00 38500.00
TOTAL 38500.00 W
Add 1 % Water charges on "W" 385.00
TOTAL 38885.00 X
Add GST on "X" (multiplying
factor 0.1405) 5463.34
TOTAL 44348.34 Y
Add 15% CPOH on "Y" 6652.25
TOTAL 51000.59 Z
Add Cess @ 1% on "Z" 510.01
Cost per test 51510.60
Say 51510.60
SUB HEAD : 20- PILE WORK 1934
20.6.1.2 Routine test (Test Load 1.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7249 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
including prepration of pile head etc. for
Single pile upto 50 tonne capacity per test 1.00 13800.00 13800.00
TOTAL 13800.00 W
Add 1 % Water charges on "W" 138.00
TOTAL 13938.00 X
Add GST on "X" (multiplying
factor 0.1405) 1958.29
TOTAL 15896.29 Y
Add 15% CPOH on "Y" 2384.44
TOTAL 18280.73 Z
Add Cess @ 1% on "Z" 182.81
Cost per test 18463.54
Say 18463.55
20.6.2 Single pile above 50 tonne and upto 100 tonne Safe capacity
20.6.2.1 Initial test (Test Load 2.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7247 Verticle load testing (INITIAL) of piles
in accordance with IS : 2911 (Part-IV)
including installation of loading platform
and prepration of pile head or
construction of test cap and
dismantling of test cap after test etc.
complete as per specification & above
50MT and upto 100MT. per test 1.00 43000.00 43000.00
TOTAL 43000.00 W
Add 1 % Water charges on "W" 430.00
TOTAL 43430.00 X
Add GST on "X" (multiplying
factor 0.1405) 6101.92
TOTAL 49531.92 Y
Add 15% CPOH on "Y" 7429.79
TOTAL 56961.70 Z
Add Cess @ 1% on "Z" 569.62
Cost per test 57531.32
Say 57531.30
20.6.2.2 Routine test (Test Load 1.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7250 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
SUB HEAD : 20- PILE WORK 1935
Code Description Unit Quantity Rate Amount
including prepration of pile head etc. for
Single pile above 50 tonne capacity
pile and upto 100 tonne capacity pile per test 1.00 22800.00 22800.00
TOTAL 22800.00 W
Add 1 % Water charges on "W" 228.00
TOTAL 23028.00 X
Add GST on "X" (multiplying
factor 0.1405) 3235.43
TOTAL 26263.43 Y
Add 15% CPOH on "Y" 3939.52
TOTAL 30202.95 Z
Add Cess @ 1% on "Z" 302.03
Cost per test 30504.98
Say 30505.00
20.6.3 Group of two or more piles upto 50 tonne Safe capacity
20.6.3.1 Initial test (Test Load 2.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7248 Verticle load testing (INITIAL) of piles
in accordance with IS : 2911 (Part-IV)
including installation of loading platform
and prepration of pile head or
construction of test cap and
dismantling of test cap after test etc.
complete as per specification & group
of two or more upto 50MT. per test 1.00 49500.00 49500.00
TOTAL 49500.00 W
Add 1 % Water charges on "W" 495.00
TOTAL 49995.00 X
Add GST on "X" (multiplying
factor 0.1405) 7024.30
TOTAL 57019.30 Y
Add 15% CPOH on "Y" 8552.89
TOTAL 65572.19 Z
Add Cess @ 1% on "Z" 655.72
Cost per test 66227.91
Say 66227.90
20.6.3.2 Routine test (Test Load 1.5 times the Safe capacity)
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7251 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
SUB HEAD : 20- PILE WORK 1936
Code Description Unit Quantity Rate Amount
including prepration of pile head etc. for
Group of two piles upto 50 tonne
capacity each per test 1.00 28500.00 28500.00
TOTAL 28500.00 W
Add 1 % Water charges on "W" 285.00
TOTAL 28785.00 X
Add GST on "X" (multiplying
factor 0.1405) 4044.29
TOTAL 32829.29 Y
Add 15% CPOH on "Y" 4924.39
TOTAL 37753.69 Z
Add Cess @ 1% on "Z" 377.54
Cost per test 38131.22
Say 38131.20
20.7 Cyclic vertical load testing of pile in accordance with IS Code of practice IS:2911
(part IV) by Kentledge method including preparation of pile head etc for.
20.7.1 Single pile
20.7.1.1 Upto 50 tonne Safe capacity pile
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7249 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
including prepration of pile head etc. for
Single pile upto 50 tonne capacity per test 1.00 13800.00 13800.00
TOTAL 13800.00 W
Add 1 % Water charges on "W" 138.00
TOTAL 13938.00 X
Add GST on "X" (multiplying
factor 0.1405) 1958.29
TOTAL 15896.29 Y
Add 15% CPOH on "Y" 2384.44
TOTAL 18280.73 Z
Add Cess @ 1% on "Z" 182.81
Cost per test 18463.54
Say 18463.55
20.7.1.2 Above 50 tonne and upto 100 tonne Safe capacity pile
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7250 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
including prepration of pile head etc. for
Single pile above 50 tonne capacity
pile and upto 100 tonne capacity pile per test 1.00 22800.00 22800.00
TOTAL 22800.00 W
Add 1 % Water charges on "W" 228.00
TOTAL 23028.00 X
SUB HEAD : 20- PILE WORK 1937
Code Description Unit Quantity Rate Amount
Add GST on "X" (multiplying
factor 0.1405) 3235.43
TOTAL 26263.43 Y
Add 15% CPOH on "Y" 3939.52
TOTAL 30202.95 Z
Add Cess @ 1% on "Z" 302.03
Cost per test 30504.98
Say 30505.00
20.7.2 Group of two or more piles
20.7.2.1 Upto 400 tonne Safe capacity of group
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7251 Cyclic verticle load testing of piles in
accordance with IS : 2911 (Part-IV)
including prepration of pile head etc. for
Group of two piles upto 50 tonne
capacity each per test 1.00 28500.00 28500.00
TOTAL 28500.00 W
Add 1 % Water charges on "W" 285.00
TOTAL 28785.00 X
Add GST on "X" (multiplying
factor 0.1405) 4044.29
TOTAL 32829.29 Y
Add 15% CPOH on "Y" 4924.39
TOTAL 37753.69 Z
Add Cess @ 1% on "Z" 377.54
Cost per test 38131.22
Say 38131.20
20.8 Lateral load testing of single pile in accordance with IS Code of practice IS :
2911 (Part IV) for determining safe allowable lateral load on pile :
20.8.1 Upto 50 tonne capacity pile
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7252 Lateral load testing of single pile in
accordance with IS : 2911 part -IV for
determining safe allowable lateral load
on pile. Upto 50 tonne capacity per test 1.00 13800.00 13800.00
TOTAL 13800.00 W
Add 1 % Water charges on "W" 138.00
TOTAL 13938.00 X
Add GST on "X" (multiplying
factor 0.1405) 1958.29
TOTAL 15896.29 Y
Add 15% CPOH on "Y" 2384.44
TOTAL 18280.73 Z
Add Cess @ 1% on "Z" 182.81
Cost per test 18463.54
Say 18463.55
SUB HEAD : 20- PILE WORK 1938
20.8.2 Above 50 tonne and upto 100 tonne capacity pile
Code Description Unit Quantity Rate Amount
Details of cost for 1 test
7253 Lateral load testing of single pile in
accordance with IS : 2911 part -IV for
determining safe allowable lateral load
on pile. Above 50 tonne capacity per test 1.00 23100.00 23100.00
TOTAL 23100.00 W
Add 1 % Water charges on "W" 231.00
TOTAL 23331.00 X
Add GST on "X" (multiplying
factor 0.1405) 3278.01
TOTAL 26609.01 Y
Add 15% CPOH on "Y" 3991.35
TOTAL 30600.36 Z
Add Cess @ 1% on "Z" 306.00
Cost per test 30906.36
Say 30906.35
20.9 Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test
method in accordance with IS 14893 including surface preparation of pile top
by removing soil, mud, dust & chipping lean concrete lumps etc. and use of
computerised equipment and high skill trained personal for conducting the test
& submission of results, all complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for one pit test (Ten pits in
one day)
MATERIAL
0081 Pile Integrity testing equipment day 0.10 3000.00 300.00
LABOUR
0160 Technician day 0.10 853.00 85.30
0161 Helper (Technician) day 0.10 645.00 64.50
Miscllaneous
9999 Reporting charges L.S. 100.67 2.12 213.42
9977 Transportation and consumables etc. L.S. 33.56 2.12 71.15
TOTAL 734.37 W
Add 1 % Water charges on "W" 7.34
TOTAL 741.71 X
Add GST on "X" (multiplying
factor 0.1405) 104.21
TOTAL 845.92 Y
Add 15% CPOH on "Y" 126.89
TOTAL 972.81 Z
Add Cess @ 1% on "Z" 9.73
Cost per test 982.54
Say 982.55
SUB HEAD : 20- PILE WORK 1939
SUB HEAD : 21.0
ALUMINIUM WORK
1941
21.1 Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate Z
sections and other sections of approved make conforming to IS: 733 and IS:
1285, fixing with dash fasteners of required dia and size, including necessary
filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM
rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever required including cleat
angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless
steel screws, all complete as per architectural drawings and the directions of
Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for
separately) :
21.1.1 For fixed portion
21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according
to IS: 1868, Minimum anodic coating of grade AC 15)
Code Description Unit Quantity Rate Amount
Details of cost for 40.02 kg
MATERIAL
(i) External member of the frame
(Jindal section no 4605)
V = 2x2.40 = 4.80 m
H = 2x3x0.95 = 5.70 m
= 10.50 m @ 1.653 kg/m = 17.36 kg
(ii) Internal member of the frame
(Jindal section no 4604)
V = 2x2.40 = 4.80 m
H = 1x3x0.95 = 2.85 m
= 7.65 m @ 1.692 kg/m = 12.94 kg
(iii) Aluminium snap beading on both
side (Jindal section no 4407)
2x6x2 (1.14+0.95) = 50.16 m
Snap beading = 50.16 m @ 0.176 kg/m
= 8.33 kg
(iv) Angle cleat 38x38x4.8 mm
50 mm long
18x0.05 = 0.900 m @ 0.985 kg/m
= 0.89 kg
Sub total =40.02 kg
Add 5% wastage = 2.00 kg
Total = 42.02 kg
7306 Aluminium T or L sections kilogram 42.02 190.00 7983.80
(v) C.P. brass /stainless steel screws
20 mm for cleat angle 18x4 = 72 Nos
0589 Chromium plated Brass screws 20 mm 100 Nos 0.72 160.00 115.20
(vi)
7389 Anodising 15 microns on aluminium
sections kilogram 42.02 38.00 1596.76
(vii)
9977 Carriage of material L.S. 52.00 2.12 110.24
LABOUR
For fabrication of frame
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
SUB HEAD : 21- ALUMINIUM WORK 1943
Code Description Unit Quantity Rate Amount
0100 Bandhani day 0.05 714.00 35.70
9999 Labour for drilling holes, hire charges of
drill, electricity charges, carriage of
dash hold fastners and sundries
L.S. 100.00 2.12 212.00
TOTAL 12980.70 W
Add 1 % Water charges on "W" 129.81
TOTAL 13110.51 X
Add GST on "X" (multiplying
factor 0.1405) 1842.03
TOTAL 14952.53 Y
Add 15% CPOH on "Y" 2242.88
TOTAL 17195.41 Z
Add Cess @ 1% on "Z" 171.95
Cost for 40.02 kg 17367.37
Cost for 1 kg 433.97
Say 433.95
21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)
Code Description Unit Quantity Rate Amount
Details of cost for 40.02 kg
MATERIAL
(i) External member of the frame
(Jindal section no 4605)
V = 2x2.40 = 4.80 m
H = 2x3x0.95 = 5.70 m
= 10.50 m @ 1.653 kg/m = 17.36 kg
(ii) Internal member of the frame
(Jindal section no 4604)
V = 2x2.40 = 4.80 m
H = 1x3x0.95 = 2.85 m
= 7.65 m @ 1.692 kg/m = 12.94 kg
(iii) Aluminium snap beading on both
side (Jindal section no 4407)
2x6x2 (1.14+0.95) = 50.16 m
Snap beading = 50.16 m @ 0.176 kg/m
= 8.33 kg
(iv) Angle cleat 38x38x4.8 mm
50 mm long
18x0.05 = 0.900 m @ 0.985 kg/m
= 0.89 kg
Sub total =40.02 kg
Add 5% wastage = 2.00 kg
Total = 42.02 kg
7306 Aluminium T or L sections kilogram 42.02 190.00 7983.80
(v) C.P. brass /stainless steel screws
20 mm for cleat angle 18x4 = 72 Nos
0589 Chromium plated Brass screws 20 mm 100 Nos 0.72 160.00 115.20
(vi) Epoxy
7392 Powder coating 50 microns on
aluminium sections kilogram 42.02 61.00 2563.22
(vii)
9977 Carriage of material L.S. 52.00 2.12 110.24
SUB HEAD : 21- ALUMINIUM WORK 1944
Code Description Unit Quantity Rate Amount
LABOUR
For fabrication of frame
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
0100 Bandhani day 0.05 714.00 35.70
9999 Labour for drilling holes, hire charges of
drill, electricity charges, carriage of
dash hold fastners and sundries L.S. 100.00 2.12 212.00
TOTAL 13947.16 W
Add 1 % Water charges on "W" 139.47
TOTAL 14086.63 X
Add GST on "X" (multiplying
factor 0.1405) 1979.17
TOTAL 16065.80 Y
Add 15% CPOH on "Y" 2409.87
TOTAL 18475.67 Z
Add Cess @ 1% on "Z" 184.76
Cost for 40.02 kg 18660.43
Cost for 1 kg 466.28
Say 466.30
21.1.1.3 Polyester powder coated aluminium (minimum thickness of polyester powder
coating 50 micron)
Code Description Unit Quantity Rate Amount
Details of cost for 40.02 kg
MATERIAL
(i) External member of the frame
(Jindal section no 4605)
V = 2x2.40 = 4.80 m
H = 2x3x0.95 = 5.70 m
= 10.50 m @ 1.653 kg/m = 17.36 kg
(ii) Internal member of the frame
(Jindal section no 4604)
V = 2x2.40 = 4.80 m
H = 1x3x0.95 = 2.85 m
= 7.65 m @ 1.692 kg/m = 12.94 kg
(iii) Aluminium snap beading on both
side (Jindal section no 4407)
2x6x2 (1.14+0.95) = 50.16 m
Snap beading = 50.16 m @
0.176 kg/m = 8.33 kg
(iv) Angle cleat 38x38x4.8 mm
50 mm long
18x0.05 = 0.900 m @ 0.985 kg/m
= 0.89 kg
Sub total =40.02 kg
Add 5% wastage = 2.00 kg
Total = 42.02 kg
7306 Aluminium T or L sections kilogram 42.02 190.00 7983.80
(v) C.P. brass /stainless steel screws
20 mm for cleat angle 18x4 = 72 Nos
SUB HEAD : 21- ALUMINIUM WORK 1945
Code Description Unit Quantity Rate Amount
0589 Chromium plated Brass screws 20 mm 100 Nos 0.72 160.00 115.20
(vi)
7393 Polyester powder coating 50 microns
on aluminium sections kilogram 42.02 67.00 2815.34
(vii)
9977 Carriage of material L.S. 52.00 2.12 110.24
LABOUR
For fabrication of frame
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
0100 Bandhani day 0.05 714.00 35.70
9999 Labour for drilling holes, hire charges of
drill, electricity charges, carriage of
dash hold fastners and sundries L.S. 100.00 2.12 212.00
TOTAL 14199.28 W
Add 1 % Water charges on "W" 141.99
TOTAL 14341.27 X
Add GST on "X" (multiplying
factor 0.1405) 2014.95
TOTAL 16356.22 Y
Add 15% CPOH on "Y" 2453.43
TOTAL 18809.65 Z
Add Cess @ 1% on "Z" 188.10
Cost for 40.02 kg 18997.75
Cost for 1 kg 474.71
Say 474.70
21.1.2 For shutters of doors, windows & ventilators including providing and fixing
hinges/ pivots and making provision for fixing of fittings wherever required
including the cost of EPDM rubber / neoprene gasket required (Fittings shall be
paid for separately)
21.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according
to IS: 1868, Minimum anodic coating of grade AC 15)
Code Description Unit Quantity Rate Amount
Details of cost for 20.21 kg
MATERIAL
(i) Hanging style (Jindal section no 4524)
1x2.35 = 2.35 m @ 2.53 kg/m = 5.95 kg
(ii) Meeting style (Jindal section no 4526)
1x2.35 = 2.35 m @ 2.465 kg/m = 5.79 kg
(iii) Top & bottom rail (Jindal section
no 4510)
2x0.75 = 1.50 m @ 2.48 kg/m = 3.72 kg
(iv) Lock rail (Jindal section no 4524)
1x0.75 = 0.75 m @ 2.53 kg/m = 1.90 kg
(v) Glazing plate (Jindal section no 440)
on one side of lock rail
1x0.75 = 0.75 m @ 0.459 kg/m
= 0.34 kg
SUB HEAD : 21- ALUMINIUM WORK 1946
Code Description Unit Quantity Rate Amount
(vi) Aluminium snap beading (Jindal
section no 4497) on both side
2x2 (0.75+1.26) = 8.04 m
2x2 (0.75+0.81) = 6.24 m
= 14.28 m @ 0.176 kg/m = 2.51 kg
(vii) Aluminium angle cleat 38x38x
4.8 mm 35 mm long
3x4x0.035 = 0.42 m @ 0.985 kg/m
= 0.41 kg
Sub total = 20.62 kg
Add 5% wastage = 1.03 kg
Total = 21.65 kg
7306 Aluminium T or L sections kilogram 21.65 190.00 4113.50
(viii)
0689 Anodised Aluminium butt hinges
100x75x4 mm 10 Nos 0.40 393.00 157.20
(ix) C.P. brass /stainless steel screws
20 mm
For cleat 12x4 = 48
For cleat 4x8 = 32
For glazing plate @ 15 cm centre to
centre in 75 cm length 2x6 = 12
Total = 92 Nos
0589 Chromium plated Brass screws 20 mm 100 Nos 0.92 160.00 147.20
(x)
7389 Anodising 15 microns on aluminium
sections kilogram 21.65 38.00 822.70
(xi)
9977 Carriage of material L.S. 31.20 2.12 66.14
(xii) Neoprene/ EPDM gasket in groove
of meeting style
7390 Neoprene/EPDM rubber gasket metre 2.35 15.00 35.25
LABOUR
For fabrication
0116 Fitter (grade 1) day 1.00 784.00 784.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 0.50 645.00 322.50
0100 Bandhani day 0.40 714.00 285.60
For fixing the shutter including hinges :
0111 Carpenter 1st class day 0.20 784.00 156.80
0114 Beldar day 0.50 645.00 322.50
9999 Labour for making provision for fittings
and carriage of screws etc. including
sundries L.S. 50.00 2.12 106.00
TOTAL 8033.39 W
Add 1 % Water charges on "W" 80.33
TOTAL 8113.73 X
Add GST on "X" (multiplying
factor 0.1405) 1139.98
TOTAL 9253.71 Y
Add 15% CPOH on "Y" 1388.06
TOTAL 10641.76 Z
Add Cess @ 1% on "Z" 106.42
Cost for 20.21 kg 10748.18
Cost for 1 kg 531.82
Say 531.80
SUB HEAD : 21- ALUMINIUM WORK 1947
21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)
Code Description Unit Quantity Rate Amount
Details of cost for 20.21 kg
MATERIAL
(i) Hanging style (Jindal section no 4524)
1x2.35 = 2.35 m @ 2.53 kg/m = 5.95 kg
(ii) Meeting style (Jindal section no 4526)
1x2.35 = 2.35 m @ 2.465 kg/m = 5.79 kg
(iii) Top & bottom rail (Jindal section
no 4510)
2x0.75 = 1.50 m @ 2.48 kg/m = 3.72 kg
(iv) Lock rail (Jindal section no 4524)
1x0.75 = 0.75 m @ 2.53 kg/m = 1.90 kg
(v) Glazing plate (Jindal section no 440)
on one side of lock rail
1x0.75 = 0.75 m @ 0.459 kg/m = 0.34 kg
(vi) Aluminium snap beading (Jindal
section no 4497) on both side
2x2 (0.75+1.26) = 8.04 m
2x2 (0.75+0.81) = 6.24 m
= 14.28 m @ 0.176 kg/m = 2.51 kg
(vii) Aluminium angle cleat 38x38x
4.8 mm 35 mm long
3x4x0.035 = 0.42 m @ 0.985 kg/m
= 0.41 kg
Sub total = 20.62 kg
Add 5% wastage = 1.03 kg
Total = 21.65 kg
7306 Aluminium T or L sections kilogram 21.65 190.00 4113.50
(viii)
0689 Anodised Aluminium butt hinges
100x75x4 mm 10 Nos 0.40 393.00 157.20
(ix) C.P. brass /stainless steel
screws 20 mm
For cleat 12x4 = 48
For cleat 4x8 = 32
For glazing plate @ 15 cm centre
to centre
in 75 cm length 2x6 = 12
Total = 92 Nos
0589 Chromium plated Brass screws 20 mm 100 Nos 0.92 160.00 147.20
(x) Epoxy
7392 Powder coating 50 microns on
aluminium sections kilogram 21.65 61.00 1320.65
(xi)
9977 Carriage of material L.S. 31.20 2.12 66.14
(xii) Neoprene/ EPDM rubber gasket in
groove of meeting style
7390 Neoprene/EPDM rubber gasket metre 2.35 15.00 35.25
LABOUR
0116 Fitter (grade 1) day 1.00 784.00 784.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 0.50 645.00 322.50
0100 Bandhani day 0.40 714.00 285.60
SUB HEAD : 21- ALUMINIUM WORK 1948
Code Description Unit Quantity Rate Amount
For fixing the shutter including hinges :
0111 Carpenter 1st class day 0.20 784.00 156.80
0114 Beldar day 0.50 645.00 322.50
9999 Labour for making provision for fittings
and carriage of screws etc. including
sundries L.S. 50.00 2.12 106.00
TOTAL 8531.34 W
Add 1 % Water charges on "W" 85.31
TOTAL 8616.66 X
Add GST on "X" (multiplying
factor 0.1405) 1210.64
TOTAL 9827.30 Y
Add 15% CPOH on "Y" 1474.09
TOTAL 11301.39 Z
Add Cess @ 1% on "Z" 113.01
Cost for 20.21 kg 11414.41
Cost for 1 kg 564.79
Say 564.80
21.1.2.3 Polyester powder coated aluminium (minimum thickness of polyester powder
coating 50 micron)
Code Description Unit Quantity Rate Amount
Details of cost for 20.21 kg
MATERIAL
(i) Hanging style (Jindal section no 4524)
1x2.35 = 2.35 m @ 2.53 kg/m = 5.95 kg
(ii) Meeting style (Jindal section no 4526)
1x2.35 = 2.35 m @ 2.465 kg/m = 5.79 kg
(iii) Top & bottom rail (Jindal section
no 4510)
2x0.75 = 1.50 m @ 2.48 kg/m = 3.72 kg
(iv) Lock rail (Jindal section no 4524)
1x0.75 = 0.75 m @ 2.53 kg/m = 1.90 kg
(v) Glazing plate (Jindal section no 440)
on one side of lock rail
1x0.75 = 0.75 m @ 0.459 kg/m
= 0.34 kg
(vi) Aluminium snap beading (Jindal
section no 4497) on both side
2x2 (0.75+1.26) = 8.04 m
2x2 (0.75+0.81) = 6.24 m
= 14.28 m @ 0.176 kg/m = 2.51 kg
(vii) Aluminium angle cleat 38x38x
4.8 mm
35 mm long
3x4x0.035 = 0.42 m @ 0.985 kg/m
= 0.41 kg
Sub total = 20.62 kg
Add 5% wastage = 1.03 kg
Total = 21.65 kg
7306 Aluminium T or L sections kilogram 21.65 190.00 4113.50
(viii)
SUB HEAD : 21- ALUMINIUM WORK 1949
Code Description Unit Quantity Rate Amount
0689 Anodised Aluminium butt hinges
100x75x4 mm 10 Nos 0.40 393.00 157.20
(ix) C.P. brass /stainless steel screws
20 mm
For cleat 12x4 = 48
For cleat 4x8 = 32
For glazing plate @ 15 cm centre to
centre in 75 cm length 2x6 = 12
Total = 92 Nos
0589 Chromium plated Brass screws 20 mm 100 Nos 0.92 160.00 147.20
(x)
7393 Polyester powder coating 50 microns
on aluminium sections kilogram 21.65 67.00 1450.55
(xi)
9977 Carriage of material L.S. 31.20 2.12 66.14
(xii) Neoprene/ EPDM rubber gasket
in groove of meeting style
7390 Neoprene/EPDM rubber gasket metre 2.35 15.00 35.25
LABOUR
For fabrication
0116 Fitter (grade 1) day 1.00 784.00 784.00
0139 Skilled Beldar (for floor rubbing etc.) day 1.00 714.00 714.00
0114 Beldar day 0.50 645.00 322.50
0100 Bandhani day 0.40 714.00 285.60
For fixing the shutter including hinges :
0111 Carpenter 1st class day 0.20 784.00 156.80
114 Beldar day 0.50 645.00 322.50
9999 Labour for making provision for fittings
and carriage of screws etc. including
sundries L.S. 50.00 2.12 106.00
TOTAL 8661.24 W
Add 1 % Water charges on "W" 86.61
TOTAL 8747.86 X
Add GST on "X" (multiplying
factor 0.1405) 1229.07
TOTAL 9976.93 Y
Add 15% CPOH on "Y" 1496.54
TOTAL 11473.47 Z
Add Cess @ 1% on "Z" 114.73
Cost for 20.21 kg 11588.20
Cost for 1 kg 573.39
Say 573.40
21.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed three
layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in
panelling fixed in aluminum doors, windows shutters and partition frames with
C.P. brass / stainless steel screws etc. complete as per architectural drawings
and directions of engineer-in-charge.
SUB HEAD : 21- ALUMINIUM WORK 1950
21.2.1 Pre-laminated particle board with decorative lamination on one side and
balancing lamination on other side
Code Description Unit Quantity Rate Amount
Details of cost for 7 sqm
MATERIAL
12 mm thick particle board = 7.00 sqm
Add 5% wastage = 0.35 sqm
Total = 7.35 sqm
7477 Prelaminated particle board with one
side decorative and other side
balancing lamination, flat pressed 3
layer & graded (medium density) Grade
I, Type II conforming to IS : 12823
(exterior grade) 12 mm thick sqm 7.35 500.00 3675.00
9977 Carriage of particle board L.S. 13.65 2.12 28.94
9999 Sundries & screws etc. L.S. 27.30 2.12 57.88
LABOUR
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 5049.41 W
Add 1 % Water charges on "W" 50.49
TOTAL 5099.91 X
Add GST on "X" (multiplying
factor 0.1405) 716.54
TOTAL 5816.45 Y
Add 15% CPOH on "Y" 872.47
TOTAL 6688.91 Z
Add Cess @ 1% on "Z" 66.89
Cost for 7 sqm 6755.80
Cost for 1 sqm 965.11
Say 965.10
21.2.2 Pre-laminated particle board with decorative lamination on both sides
Code Description Unit Quantity Rate Amount
Details of cost for 7 sqm
MATERIAL
12 mm thick particle board = 7.00 sqm
Add 5% wastage = 0.35 sqm
Total = 7.35 sqm
7480 Prelaminated particle board with both
sides decorative lamination, flat
pressed 3 layer & graded (medium
density) Grade I, Type II conforming to
IS : 12823 (exterior grade) 12 mm thick sqm 7.35 490.00 3601.50
9977 Carriage of particle board L.S. 13.65 2.12 28.94
9999 Sundries & screws etc. L.S. 27.30 2.12 57.88
LABOUR
0112 Carpenter 2nd class day 0.90 714.00 642.60
SUB HEAD : 21- ALUMINIUM WORK 1951
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.00 645.00 645.00
TOTAL 4975.91 W
Add 1 % Water charges on "W" 49.76
TOTAL 5025.67 X
Add GST on "X" (multiplying
factor 0.1405) 706.11
TOTAL 5731.78 Y
Add 15% CPOH on "Y" 859.77
TOTAL 6591.55 Z
Add Cess @ 1% on "Z" 65.92
Cost for 7 sqm 6657.46
Cost for 1 sqm 951.07
Say 951.05
21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters
and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per
the architectural drawings and the directions of engineer-in-charge . (Cost of
aluminium snap beading shall be paid in basic item):
21.3.1 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 sqm
MATERIAL
Float Glass panes 4.0 mm thick
= 1.00 sqm
Add for wastage & breakage @ 10%
= 0.10 sqm
Total =1.10 sqm
2406 Float glass sheet of nominal thickness
4 mm (weight not less than 10kg/sqm). sqm 1.10 309.00 339.90
9977 Carriage of glass L.S. 2.42 2.12 5.13
7390 Neoprene/EPDM rubber gasket metre 6.00 15.00 90.00
LABOUR
0112 Carpenter 2nd class day 0.23 714.00 164.22
0114 Beldar day 0.23 645.00 148.35
9988 Sundries and carriage of gasket L.S. 6.89 2.12 14.61
TOTAL 762.21 W
Add 1 % Water charges on "W" 7.62
TOTAL 769.83 X
Add GST on "X" (multiplying
factor 0.1405) 108.16
TOTAL 877.99 Y
Add 15% CPOH on "Y" 131.70
TOTAL 1009.69 Z
Add Cess @ 1% on "Z" 10.10
Cost for 1 sqm 1019.79
Say 1019.80
SUB HEAD : 21- ALUMINIUM WORK 1952
21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 sqm
MATERIAL
Glass panes 5.50 mm thick = 1.00 sqm
Add for wastage & breakage @ 10%
= 0.10 sqm
Total =1.00 sqm
2407 Float glass sheet of nominal thickness
5 mm (weight not less than
12.50 kg/sqm) sqm 1.10 515.00 566.50
9977 Carriage of glass L.S. 3.33 2.12 7.06
7390 Neoprene/EPDM rubber gasket metre 6.00 15.00 90.00
LABOUR
0112 Carpenter 2nd class day 0.23 714.00 164.22
0114 Beldar day 0.23 645.00 148.35
9988 Sundries and carriage of gasket L.S. 6.89 2.12 14.61
TOTAL 990.74 W
Add 1 % Water charges on "W" 9.91
TOTAL 1000.64 X
Add GST on "X" (multiplying
factor 0.1405) 140.59
TOTAL 1141.23 Y
Add 15% CPOH on "Y" 171.19
TOTAL 1312.42 Z
Add Cess @ 1% on "Z" 13.12
Cost for 1 sqm 1325.54
Say 1325.55
21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 sqm
MATERIAL
Float Glass panes 8.0 mm thick
= 1.00 sqm
Add for wastage & breakage @ 10%
= 0.10 sqm
Total =1.10 sqm
2408 Float glass sheet of nominal thickness
8 mm.(weight not less than
20.00 kg/sqm). sqm 1.10 628.00 690.80
9977 Carriage of glass L.S. 4.84 2.12 10.26
7390 Neoprene/EPDM rubber gasket metre 6.00 15.00 90.00
LABOUR
0112 Carpenter 2nd class day 0.23 714.00 164.22
0114 Beldar day 0.23 645.00 148.35
SUB HEAD : 21- ALUMINIUM WORK 1953
Code Description Unit Quantity Rate Amount
9988 Sundries and carriage of gasket L.S. 6.89 2.12 14.61
TOTAL 1118.24 W
Add 1 % Water charges on "W" 11.18
TOTAL 1129.42 X
Add GST on "X" (multiplying
factor 0.1405) 158.68
TOTAL 1288.10 Y
Add 15% CPOH on "Y" 193.22
TOTAL 1481.32 Z
Add Cess @ 1% on "Z" 14.81
Cost for 1 sqm 1496.13
Say 1496.15
21.4 Providing and fixing double action hydraulic floor spring of approved brand
and manufacture conforming to IS : 6315, having brand logo embossed on the
body / plate with double spring mechanism and door weight upto 125 kg, for
doors, including cost of cutting floors, embedding in floors as required and
making good the same matching to the existing floor finishing and cover plates
with brass pivot and single piece M.S. sheet outer box with slide plate etc.
complete as per the direction of Engineer-in-charge.
21.4.1 With stainless steel cover plate minimum 1.25 mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for one number
MATERIAL
7394 Double action hydraulic floor spring
with stainless steel cover plate each 1.00 1500.00 1500.00
9977 CARRIAGE L.S. 13.00 2.12 27.56
9999 Sundries and screws L.S. 26.00 2.12 55.12
Cement concrete 1:2:4
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete work cum 0.002 7365.15 14.73 A
LABOUR
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
0112 Carpenter 2nd class day 0.01 714.00 7.14
0114 Beldar day 0.17 645.00 109.65
TOTAL 1834.04 W
Add 1 % Water charges on "W-A" 18.19
TOTAL 1852.23 X
Add GST on "X-A" (multiplying
factor 0.1405) 258.17
TOTAL 2110.40 Y
Add 15% CPOH on "Y-A" 314.35
TOTAL 2424.75 Z
Add Cess @ 1% on "Z-A" 24.10
Cost for each 2448.85
Say 2448.85
SUB HEAD : 21- ALUMINIUM WORK 1954
21.4.2 With brass cover plate minimum 1.25 mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for one number
MATERIAL
7396 Double action hydraulic floor spring
with brass cover plate each 1.00 1620.00 1620.00
9977 CARRIAGE L.S. 13.00 2.12 27.56
9999 Sundries and screws L.S. 26.00 2.12 55.12
Cement concrete 1:2:4
4.1.3 Rate as per item no. 4.1.3 of
SH : concrete work cum 0.002 7365.15 14.73 A
LABOUR
For cutting hole and making it good
0123 Mason (brick layer) 1st class day 0.08 784.00 62.72
0124 Mason (brick layer) 2nd class day 0.08 714.00 57.12
0112 Carpenter 2nd class day 0.01 714.00 7.14
0114 Beldar day 0.17 645.00 109.65
TOTAL 1954.04 W
Add 1 % Water charges on "W-A" 19.39
TOTAL 1973.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 275.20
TOTAL 2248.63 Y
Add 15% CPOH on "Y-A" 335.09
TOTAL 2583.72 Z
Add Cess @ 1% on "Z-A" 25.69
Cost for each 2609.41
Say 2609.40
21.5 Providing and fixing powder coated aluminium work (minimum thickness of
powder coating 50 micron) consisting of tee/ angle sections, of approved make
conforming to IS : 733 in frames of false ceiling including aluminium angle cleats
with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter
angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre
and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary
cadmium plated machine screws all complete as per approved architectural
drawings and direction of the Engineer-in-charge (level adjusting hangers,
ceiling cleats and expansion hold fasteners to be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for 6.35 kg (2.40x2.40
= 5.76 sqm)
MATERIAL
(i) Aluminium main runner - assuming
Tee of size 35x23.5x1.5 mm @ 600
mm centre to centre
3x2.40 m = 7.20 m
Extra for light fittings
2x1.20 m = 2.40 m
Total= 9.60 m @ 0.247 kg/m = 2.370 kg
SUB HEAD : 21- ALUMINIUM WORK 1955
Code Description Unit Quantity Rate Amount
Aluminium cross runner - assuming
Tee of size 35x23.5x1.5 mm @
600 mm centre to centre
3x4x0.60 m = 7.20 m
(-) 2x0.30 = (-) 0.60 m
Total=6.60 m @ 0.247 kg/m = 1.630 kg
Perimeter angle aluminium - assuming
size 25.4x25.4x1.63 mm @ 600 mm
centre to centre
4x2.40 m = 9.60 m @ 0.213 kg/m
= 2.045 kg
(ii) CLEATS
Aluminium angle- assuming size
25.4x25.4x1.63 mm
Extra for light fittings =3x2x2 = 12.00
Corner = 4.00
For joining runners = 42.00
Total = 58.00x0.025 = 1.45 m @
0.213 kg/m = 0.309 kg
Sub total = 2.370 + 1.630 + 2.045
+ 0.309 =6.354 kg
Add 5% wastage = 0.318 kg
Total = 6.672 kg
7306 Aluminium T or L sections kilogram 6.672 190.00 1267.68
(iii) C.P. brass/ stainless steel screws
20 mm for angle cleats
0589 Chromium plated Brass screws 20 mm 100 Nos 0.0116 160.00 1.86
(iv) Rawl plug for fixing perimeter angles
7048 Rawl plug 50 mm (designation 10 no.) each 24.00 22.00 528.00
Epoxy
7392 Powder coating 50 microns on
aluminium sections kilogram 6.67 61.00 406.87
(vi)
9977 Carriage of material L.S. 13.00 2.12 27.56
(vii)
9999 C.P. brass screws for fixing frame with
suspenders L.S. 13.00 2.12 27.56
LABOUR
For fabrication and erection
0111 Carpenter 1st class day 0.64 784.00 501.76
0114 Beldar day 0.64 645.00 412.80
9999 Scaffolding and sundries L.S. 13.00 2.12 27.56
TOTAL 3201.65 W
Add 1 % Water charges on "W" 32.02
TOTAL 3233.66 X
Add GST on "X" (multiplying
factor 0.1405) 454.33
TOTAL 3687.99 Y
Add 15% CPOH on "Y" 553.20
TOTAL 4241.19 Z
Add Cess @ 1% on "Z" 42.41
Cost for 6.35 kg 4283.60
Cost for 1 kg 674.58
Say 674.60
SUB HEAD : 21- ALUMINIUM WORK 1956
21.6 Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length),
fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size
60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50
mm long, complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 23 nos (hangers in
2.40 mx 2.40 m = 5.76 sqm)one number
MATERIAL
6 mm dia G.I. adjustable hangers
including clips (upto 1.20 metre length).
For light fitting 2x4 = 8.00
For runners = 15.00
Total = 23.00
7395 6 mm dia. G.I. adjustable hangers
including clips (upto 1.2 m length) each 23.00 20.00 460.00
Ceiling cleats
G.I. flat 40X3 mm 60mm long
23x0.06 = 1.38 m @ 0.95kg/m = 1.31kg
Add 5% wastage = 0.07 kg
Total = 1.38 kg say 0.014 q
0992 Galvanised steel plain sheets quintal 0.014 5000.00 70.00
7388 Dash hold fastener 12.5 mm dia, 40 mm
long with 6 mm dia bolt each 23.00 10.00 230.00
9977 Carriage of materials L.S. 5.20 2.12 11.02
LABOUR
0111 Carpenter 1st class day 0.35 784.00 274.40
0114 Beldar day 0.27 645.00 174.15
TOTAL 1219.57 W
Add 1 % Water charges on "W" 12.20
TOTAL 1231.77 X
Add GST on "X" (multiplying
factor 0.1405) 173.06
TOTAL 1404.83 Y
Add 15% CPOH on "Y" 210.73
TOTAL 1615.56 Z
Add Cess @ 1% on "Z" 16.16
Cost for 23 hangers 1631.71
Cost for one hanger 70.94
Say 70.95
21.7 Providing and fixing machine moulded aluminium covering of approved pattern
& design, made out of machine cut aluminium sheet and machine holed for
receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors,
the fixing on plate in one row on one side of joint only shall be done with stainless
steel dash fasteners of 8 mm dia and 75 mm long bolt including providing
aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm
centre to centre including drilling holes in the receiving surface and providing
expandable plastic sleeves in holes etc. complete as per direction of Engineer-
in-charge.
SUB HEAD : 21- ALUMINIUM WORK 1957
21.7.1 Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required
shade according to IS: 1868, Minimum anodic coating of grade AC 15)
Code Description Unit Quantity Rate Amount
Details of cost for 7.00 kg
MATERIAL
Anodised aluminium sheet 2.5 mm
thick, 170 mm wide
5.88 m x0.17 m = 1.00 sqm @ 7.00 kg/
sqm = 7.00 kg
Add 5% wastage = 0.35 kg
Total = 7.35 kg
2704 Aluminium Strip 40 mm wide and 2 mm
thick kilogram 7.35 240.00 1764.00
7389 Anodising 15 microns on aluminium
sections kilogram 7.35 38.00 279.30
7347 Cadmium plated full threaded steel
screws (30x4 mm dia.) 100 Nos 0.30 27.00 8.10
7348 Aluminium washer 2 mm thick
15 mm dia 100 Nos 0.30 10.00 3.00
8776 Stainless steel dash fastener of
8 mm dia and 75 mm long bolt each 30.00 17.00 510.00
9977 Carriage of materials L.S. 6.50 2.12 13.78
LABOUR
0112 Carpenter 2nd class day 0.392 714.00 279.89
0114 Beldar day 0.392 645.00 252.84
9999 Sundries including machine work L.S. 21.45 2.12 45.47
TOTAL 3156.38 W
Add 1 % Water charges on "W" 31.56
TOTAL 3187.95 X
Add GST on "X" (multiplying
factor 0.1405) 447.91
TOTAL 3635.85 Y
Add 15% CPOH on "Y" 545.38
TOTAL 4181.23 Z
Add Cess @ 1% on "Z" 41.81
Cost for 7.00 kg 4223.04
Cost for 1 kg 603.29
Say 603.30
21.7.2 Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder
coating 50 micron)
Code Description Unit Quantity Rate Amount
Details of cost for 7.00 kg
MATERIAL
Anodised aluminium sheet 2.5 mm
thick, 170 mm wide
5.88 m x0.17 m = 1.00 sqm @
7.00 kg/sqm = 7.00 kg
Add 5% wastage = 0.35 kg
Total = 7.35 kg
2704 Aluminium Strip 40 mm wide and
2 mm thick kilogram 7.35 240.00 1764.00
SUB HEAD : 21- ALUMINIUM WORK 1958
Code Description Unit Quantity Rate Amount
7392 Powder coating 50 microns on
aluminium sections kilogram 7.35 61.00 448.35
7347 Cadmium plated full threaded steel
screws (30x4 mm dia.) 100 Nos 0.30 27.00 8.10
7348 Aluminium washer 2 mm thick
15 mm dia 100 Nos 0.30 10.00 3.00
8776 Stainless steel dash fastener of
8 mm dia and 75 mm long bolt each 30.00 17.00 510.00
9977 Carriage of materials L.S. 6.50 2.12 13.78
LABOUR
0112 Carpenter 2nd class day 0.392 714.00 279.89
0114 Beldar day 0.392 645.00 252.84
9999 Sundries including machine work L.S. 21.45 2.12 45.47
TOTAL 3325.43 W
Add 1 % Water charges on "W" 33.25
TOTAL 3358.69 X
Add GST on "X" (multiplying
factor 0.1405) 471.90
TOTAL 3830.58 Y
Add 15% CPOH on "Y" 574.59
TOTAL 4405.17 Z
Add Cess @ 1% on "Z" 44.05
Cost for 7.00 kg 4449.22
Cost for 1 kg 635.60
Say 635.60
21.8 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work
by providing weather silicon sealant over backer rod of approved quality as per
architectural drawings and direction of Engineer-in-charge complete.
21.8.1 Upto 5mm depth and 5 mm width
Code Description Unit Quantity Rate Amount
Details of cost for 1 metre
MATERIAL
8646 Silicon sealant cartridge 0.087 112.00 9.74
(i/c 5% wastage)
8654 Masking tape metre 2.00 2.18 4.36
9999 Sundries & profile L.S. 2.60 2.12 5.51
9999 LABOUR L.S. 20.80 2.12 44.10
TOTAL 63.71 W
Add 1 % Water charges on "W" 0.64
TOTAL 64.35 X
Add GST on "X" (multiplying
factor 0.1405) 9.04
TOTAL 73.39 Y
Add 15% CPOH on "Y" 11.01
TOTAL 84.40 Z
Add Cess @ 1% on "Z" 0.84
Cost for 1 metre 85.24
Say 85.25
SUB HEAD : 21- ALUMINIUM WORK 1959
21.9 Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium
extruded sections.
21.9.1 For fixed portion
Code Description Unit Quantity Rate Amount
Details of cost for 41.09 kg
Difference in cost of
7391 Anodising 25 microns on aluminium
sections kilogram 41.09 48.00 1972.32
7389 Anodising 15 microns on aluminium
sections kilogram -41.09 38.00 -1561.42
TOTAL 410.90 W
Add 1 % Water charges on "W" 4.11
TOTAL 415.01 X
Add GST on "X" (multiplying
factor 0.1405) 58.31
TOTAL 473.32 Y
Add 15% CPOH on "Y" 71.00
TOTAL 544.32 Z
Add Cess @ 1% on "Z" 5.44
Cost for 41.09 kg 549.76
Cost for 1 kg 13.38
Say 13.40
21.9.2 For shutters of doors, windows & ventilators
Code Description Unit Quantity Rate Amount
Details of cost for 21.65 kg
Difference in cost of
7391 Anodising 25 microns on aluminium
sections kilogram 21.65 48.00 1039.20
7389 Anodising 15 microns on aluminium
sections kilogram -21.65 38.00 -822.70
TOTAL 216.50 W
Add 1 % Water charges on "W" 2.17
TOTAL 218.67 X
Add GST on "X" (multiplying
factor 0.1405) 30.72
TOTAL 249.39 Y
Add 15% CPOH on "Y" 37.41
TOTAL 286.80 Z
Add Cess @ 1% on "Z" 2.87
Cost for 21.65kg 289.66
Cost for 1 kg 13.38
Say 13.40
SUB HEAD : 21- ALUMINIUM WORK 1960
21.10 Providing and fixing double glazed hermetically sealed glazing in aluminium
windows, ventilators and partition etc. with 6 mm thick clear float glass both
side, having 12 mm air gap, including providing EPDM gasket, perforated
aluminium spacers, desiccants, sealant (Both primary and secondary sealant)
etc. as per specifications, drawings and direction of Engineer-in-charge
complete.
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 sqm
MATERIAL
Hermetically sealled double glazed unit
made with 6mm thick clear float glass
both side having 12 mm air gap
= 1.00 sqm.
Add for wastage & breakage @ 10%
= 0.10 sqm
Total = 1.10 sqm
8648 Hermetically sealed double glazed unit
made with 6 mm thick clear float glass
both side having 12 mm air gap sqm 1.10 2200.00 2420.00
9977 Carriage of glass L.S. 6.66 2.12 14.12
7390 Neoprene/EPDM rubber gasket metre 6.00 15.00 90.00
LABOUR
Glazier /
0112 Carpenter 2nd class day 0.23 714.00 164.22
0114 Beldar day 0.46 645.00 296.70
9988 Sundries and carriage of gasket L.S. 6.89 2.12 14.61
TOTAL 2999.65 W
Add 1 % Water charges on "W" 30.00
TOTAL 3029.64 X
Add GST on "X" (multiplying
factor 0.1405) 425.66
TOTAL 3455.31 Y
Add 15% CPOH on "Y" 518.30
TOTAL 3973.60 Z
Add Cess @ 1% on "Z" 39.74
Cost for 1 sqm 4013.34
Say 4013.35
21.11 Providing and fixing stainless steel (SS 304 grade) adjustable friction windows
stays of approved quality with necessary stainless steel screws etc. to the side
hung windows as per direction of Engineer-in-charge complete.
21.11.1 205 X 19 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
8649 Stainless steel (SS 304 grade)
adjustable friction window stay 205 x
19 mm each 10.00 197.80 1978.00
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.40 35.84 14.34
9977 CARRIAGE L.S. 2.73 2.12 5.79
SUB HEAD : 21- ALUMINIUM WORK 1961
Code Description Unit Quantity Rate Amount
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.14 645.00 90.30
TOTAL 2188.38 W
Add 1 % Water charges on "W" 21.88
TOTAL 2210.27 X
Add GST on "X" (multiplying
factor 0.1405) 310.54
TOTAL 2520.81 Y
Add 15% CPOH on "Y" 378.12
TOTAL 2898.93 Z
Add Cess @ 1% on "Z" 28.99
Cost for 10 nos 2927.92
Cost for each 292.79
Say 292.80
21.11.2 255 X 19 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
8650 Stainless steel (SS 304 grade)
adjustable 255 x 19mm each 10.00 225.00 2250.00
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.40 35.84 14.34
9977 CARRIAGE L.S. 2.73 2.12 5.79
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.14 645.00 90.30
TOTAL 2460.38 W
Add 1 % Water charges on "W" 24.60
TOTAL 2484.99 X
Add GST on "X" (multiplying
factor 0.1405) 349.14
TOTAL 2834.13 Y
Add 15% CPOH on "Y" 425.12
TOTAL 3259.25 Z
Add Cess @ 1% on "Z" 32.59
Cost for 10 nos 3291.84
Cost for each 329.18
Say 329.20
21.11.3 355 X 19 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
8651 Stainless steel (SS 304 grade)
adjustable friction window stay 355 x
19 mm each 10.00 195.00 1950.00
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.40 35.84 14.34
9977 CARRIAGE L.S. 2.73 2.12 5.79
SUB HEAD : 21- ALUMINIUM WORK 1962
Code Description Unit Quantity Rate Amount
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.14 645.00 90.30
TOTAL 2160.38 W
Add 1 % Water charges on "W" 21.60
TOTAL 2181.99 X
Add GST on "X" (multiplying
factor 0.1405) 306.57
TOTAL 2488.56 Y
Add 15% CPOH on "Y" 373.28
TOTAL 2861.84 Z
Add Cess @ 1% on "Z" 28.62
Cost for 10 nos 2890.46
Cost for each 289.05
Say 289.05
21.11.4 510 X 19 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
8652 Stainless steel (SS 304 grade)
adjustable friction window stay 510 x
19 mm each 10.00 535.00 5350.00
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.40 35.84 14.34
9977 CARRIAGE L.S. 2.73 2.12 5.79
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.14 645.00 90.30
TOTAL 5560.38 W
Add 1 % Water charges on "W" 55.60
TOTAL 5615.99 X
Add GST on "X" (multiplying
factor 0.1405) 789.05
TOTAL 6405.03 Y
Add 15% CPOH on "Y" 960.76
TOTAL 7365.79 Z
Add Cess @ 1% on "Z" 73.66
Cost for 10 nos 7439.45
Cost for each 743.94
Say 743.95
21.11.5 710 X 19 mm
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos.
MATERIAL
8653 Stainless steel (SS 304 grade)
adjustable friction window stay 710 x
19 mm each 10.00 925.00 9250.00
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.40 35.84 14.34
9977 CARRIAGE L.S. 2.73 2.12 5.79
SUB HEAD : 21- ALUMINIUM WORK 1963
Code Description Unit Quantity Rate Amount
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.14 645.00 90.30
TOTAL 9460.38 W
Add 1 % Water charges on "W" 94.60
TOTAL 9554.99 X
Add GST on "X" (multiplying
factor 0.1405) 1342.48
TOTAL 10897.46 Y
Add 15% CPOH on "Y" 1634.62
TOTAL 12532.08 Z
Add Cess @ 1% on "Z" 125.32
Cost for 10 nos 12657.40
Cost for each 1265.74
Say 1265.75
21.12 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm
thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-
in-Charge.
21.12.1 Anodized (AC 15 ) aluminium tubular handle bar
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos handle bar.
MATERIAL
10x22/7 x 1/4 (0.032x0.032 - 0.026 x
0.026) x 2.10 = 0.0057 cum
0.0057 cum @ 2710 kg/ cum = 15.56kg
Add 5% wastage 0.78 kg
Total = 16.34 kg
7306 Aluminium T or L sections kilogram 16.34 190.00 3104.60
7389 Anodising 15 microns on aluminium
sections kilogram 16.34 38.00 620.92
9977 Carriage of material L.S. 4.42 2.12 9.37
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.08 35.84 2.87
LABOUR
0111 Carpenter 1st class day 0.125 784.00 98.00
TOTAL 3835.76 W
Add 1 % Water charges on "W" 38.36
TOTAL 3874.12 X
Add GST on "X" (multiplying
factor 0.1405) 544.31
TOTAL 4418.43 Y
Add 15% CPOH on "Y" 662.76
TOTAL 5081.19 Z
Add Cess @ 1% on "Z" 50.81
Cost of 10 nos 5132.00
Cost of 1 no 513.20
Say 513.20
SUB HEAD : 21- ALUMINIUM WORK 1964
21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos handle bar.
MATERIAL
10x22/7 x 1/4 (0.032x0.032 - 0.026 x
0.026) x 2.10 = 0.0057 cum
0.0057 cum @ 2710 kg/ cum = 15.56kg
Add 5% wastage 0.78 kg
Total = 16.34 kg
7306 Aluminium T or L sections kilogram 16.34 190.00 3104.60
Epoxy
7392 Powder coating 50 microns on
aluminium sections kilogram 16.34 61.00 996.74
9977 Carriage of material L.S. 4.42 2.12 9.37
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.08 35.84 2.87
LABOUR
0111 Carpenter 1st class day 0.125 784.00 98.00
TOTAL 4211.58 W
Add 1 % Water charges on "W" 42.12
TOTAL 4253.69 X
Add GST on "X" (multiplying
factor 0.1405) 597.64
TOTAL 4851.34 Y
Add 15% CPOH on "Y" 727.70
TOTAL 5579.04 Z
Add Cess @ 1% on "Z" 55.79
Cost of 10 nos 5634.83
Cost of 1 no 563.48
Say 563.50
21.12.3 Polyester powder coated minimum thickness 50 micron aluminium tubular
handle bar
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos handle bar.
MATERIAL
10x22/7 x 1/4 (0.032x0.032 -0.026 x
0.026) x 2.10 = 0.0057 cum
0.0057 cum @ 2710 kg/ cum = 15.56kg
Add 5% wastage 0.78 kg
Total = 16.34 kg
7306 Aluminium T or L sections kilogram 16.34 190.00 3104.60
7393 Polyester powder coating 50 microns
on aluminium sections kilogram 16.34 67.00 1094.78
9977 Carriage of material L.S. 4.42 2.12 9.37
8647 Stainless steel screws 30 mm x4 mm 100 nos 0.08 35.84 2.87
SUB HEAD : 21- ALUMINIUM WORK 1965
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.125 784.00 98.00
TOTAL 4309.62 W
Add 1 % Water charges on "W" 43.10
TOTAL 4352.71 X
Add GST on "X" (multiplying
factor 0.1405) 611.56
TOTAL 4964.27 Y
Add 15% CPOH on "Y" 744.64
TOTAL 5708.91 Z
Add Cess @ 1% on "Z" 57.09
Cost of 10 nos 5766.00
Cost of 1 no 576.60
Say 576.60
21.13 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without
pair of handles (best make of approved quality) for aluminium doors including
necessary cutting and making good etc. complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 1 nos.
MATERIAL
7001 Brass 100mm mortice latch and lock
with 6 levers without pair of handles each 1.00 195.00 195.00
LABOUR
0111 Carpenter 1st class day 0.17 784.00 133.28
9999 Sundry and screws L.S. 3.64 2.12 7.72
TOTAL 336.00 W
Add 1 % Water charges on "W" 3.36
TOTAL 339.36 X
Add GST on "X" (multiplying
factor 0.1405) 47.68
TOTAL 387.04 Y
Add 15% CPOH on "Y" 58.06
TOTAL 445.09 Z
Add Cess @ 1% on "Z" 4.45
Cost of 1 no 449.54
Say 449.55
21.14 Providing and fixing anodised aluminium (anodised transparent or dyed to
required shade according to IS: 1868. Minimum anodic coating of grade AC 15)
sub frame work for windows and ventilators with extruded built up standard
tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed
with dash fastener of required dia and size (Dash fastener to be paid for
separately).
Code Description Unit Quantity Rate Amount
Details of cost for 4.082kg
MATERIAL
SUB HEAD : 21- ALUMINIUM WORK 1966
Code Description Unit Quantity Rate Amount
Aluminium Section
(i) External member of the frame
(Jindal section no TU/ 3644)
V = 2x2.00 = 4.00 m
H = 2x1.20 = 2.40 m
Total= 6.40 m @ 0.607 kg/m = 3.885kg
Angle cleat 38x38x4.8 mm 50 mm long
4x0.05 = 0.200 m @ 0.985 kg/m
= 0.197 kg
sub total = 4.082kg.
Add 5% wastage = 0.204kg
Total = 4.286kg
7306 Aluminium T or L sections kilogram 4.286 190.00 814.34
0589 Chromium plated Brass screws 20 mm 100 Nos 0.08 160.00 12.80
7389 Anodising 15 microns on aluminium
sections kilogram 4.286 38.00 162.87
9977 Carriage of material L.S. 5.20 2.12 11.02
LABOUR
For fabrication of frame
0116 Fitter (grade 1) day 0.04 784.00 31.36
0139 Skilled Beldar (for floor rubbing etc.) day 0.04 714.00 28.56
0114 Beldar day 0.02 645.00 12.90
0100 Bandhani day 0.01 714.00 7.14
9999 Labour for drilling holes, hire charges of
drill, electricity charges, carriage of
dash hold fastners & sundries L.S. 5.20 2.12 11.02
TOTAL 1092.02 W
Add 1 % Water charges on "W" 10.92
TOTAL 1102.94 X
Add GST on "X" (multiplying
factor 0.1405) 154.96
TOTAL 1257.90 Y
Add 15% CPOH on "Y" 188.68
TOTAL 1446.58 Z
Add Cess @ 1% on "Z" 14.47
Cost for 4.082 kg 1461.05
Cost for 1 kg 357.92
Say 357.90
21.15 Providing and fixing aluminium casement windows fastener of required length
for aluminium windows with necessary screws etc. complete.
21.15.1 Anodized (AC 15) aluminium
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos.
MATERIAL
8660 Aluminium casement window fastener
(Anodised AC 15) each 10.00 48.00 480.00
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
SUB HEAD : 21- ALUMINIUM WORK 1967
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 549.55 W
Add 1 % Water charges on "W" 5.50
TOTAL 555.04 X
Add GST on "X" (multiplying
factor 0.1405) 77.98
TOTAL 633.03 Y
Add 15% CPOH on "Y" 94.95
TOTAL 727.98 Z
Add Cess @ 1% on "Z" 7.28
Cost of 10 nos 735.26
Cost of 1 nos 73.53
Say 73.55
21.15.2 Powder coated minimum thickness 50 micron aluminium
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos.
MATERIAL
8661 Aluminium casement window fastener
(powder coated ) each 10.00 52.64 526.40
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 595.95 W
Add 1 % Water charges on "W" 5.96
TOTAL 601.91 X
Add GST on "X" (multiplying
factor 0.1405) 84.57
TOTAL 686.48 Y
Add 15% CPOH on "Y" 102.97
TOTAL 789.45 Z
Add Cess @ 1% on "Z" 7.89
Cost of 10 nos 797.34
Cost of 1 nos 79.73
Say 79.75
21.15.3 Polyester powder coated minimum thickness 50 micron aluminium
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos.
MATERIAL
8662 Aluminium casement window fastener
(polyester powder coated) each 10.00 51.52 515.20
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
SUB HEAD : 21- ALUMINIUM WORK 1968
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 584.75 W
Add 1 % Water charges on "W" 5.85
TOTAL 590.60 X
Add GST on "X" (multiplying
factor 0.1405) 82.98
TOTAL 673.57 Y
Add 15% CPOH on "Y" 101.04
TOTAL 774.61 Z
Add Cess @ 1% on "Z" 7.75
Cost of 10 nos 782.36
Cost of 1 nos 78.24
Say 78.25
21.16 Providing and fixing aluminium round shape handle of outer dia 100 mm with
SS screws etc. complete as per direction of Engineer-in-charge
21.16.1 Anodized (AC 15 ) aluminium
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos.
MATERIAL
8663 Aluminium round shape handle
(anodised AC 15) outer dia 100mm each 10.00 59.36 593.60
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 663.15 W
Add 1 % Water charges on "W" 6.63
TOTAL 669.78 X
Add GST on "X" (multiplying
factor 0.1405) 94.10
TOTAL 763.88 Y
Add 15% CPOH on "Y" 114.58
TOTAL 878.47 Z
Add Cess @ 1% on "Z" 8.78
Cost of 10 nos 887.25
Cost of 1 nos 88.73
Say 88.75
21.16.2 Powder coated minimum thickness 50 micron aluminium
Code Description Unit Quantity Rate Amount
8664 Aluminium round shape handle
(powder coated) outer dia 100 mm each 10.00 60.00 600.00
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
SUB HEAD : 21- ALUMINIUM WORK 1969
Code Description Unit Quantity Rate Amount
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 669.55 W
Add 1 % Water charges on "W" 6.70
TOTAL 676.24 X
Add GST on "X" (multiplying
factor 0.1405) 95.01
TOTAL 771.26 Y
Add 15% CPOH on "Y" 115.69
TOTAL 886.94 Z
Add Cess @ 1% on "Z" 8.87
Cost of 10 nos 895.81
Cost of 1 nos 89.58
Say 89.60
21.16.3 Polyester powder coated minimum thickness 50 micron aluminium
Code Description Unit Quantity Rate Amount
Detail of cost for 10 nos.
MATERIAL
8665 Aluminium round shape handle
(polyester powder coated) outer dia
100 mm each 10.00 62.00 620.00
8666 Stainless steel screws 25 mm x4 mm 100 Nos 0.40 41.80 16.72
LABOUR
0111 Carpenter 1st class day 0.06 784.00 47.04
9977 Carriage of materials L.S. 2.73 2.12 5.79
TOTAL 689.55 W
Add 1 % Water charges on "W" 6.90
TOTAL 696.44 X
Add GST on "X" (multiplying
factor 0.1405) 97.85
TOTAL 794.29 Y
Add 15% CPOH on "Y" 119.14
TOTAL 913.44 Z
Add Cess @ 1% on "Z" 9.13
Cost of 10 nos 922.57
Cost of 1 nos 92.26
Say 92.25
21.17 Providing and fixing anodised aluminium grill (anodised transparent or dyed to
required shade according to IS: 1868 with minimum anodic coating of grade AC
15) of approved design/pattern, with approved standard section and fixed to
the existing window frame with C.P. brass/ stainless steel screws @ 200 mm
centre to centre, including cutting the grill to proper opening size for fixing and
operation of handles and fixing approved anodised aluminium standard section
around the opening, all complete as per requirement and direction of Engineer-
in-charge. (Only weight of grill to be measured for payment).
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 kg
MATERIAL
SUB HEAD : 21- ALUMINIUM WORK 1970
Code Description Unit Quantity Rate Amount
Anodised aluminium grill = 10.00 kg
Add 20% wastage = 2 kg = 12 kg
8774 Aluminium Grill kg 12.00 279.00 3348.00
9977 Carriage of materials L.S. 11.00 2.12 23.32
LABOUR
for fixing
0116 Fitter (grade 1) day 0.50 784.00 392.00
0139 Skilled Beldar (for floor rubbing etc.) day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
0100 Bandhani day 0.05 714.00 35.70
9999 Sundries L.S. 25.00 2.12 53.00
TOTAL 4191.77 W
Add 1 % Water charges on "W" 41.92
TOTAL 4233.69 X
Add GST on "X" (multiplying
factor 0.1405) 594.83
TOTAL 4828.52 Y
Add 15% CPOH on "Y" 724.28
TOTAL 5552.80 Z
Add Cess @ 1% on "Z" 55.53
Cost for 10.00 kg 5608.33
Cost for 1 kg 560.83
Say 560.85
21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of
approved brand and manufacture, including providing and fixing top & bottom
pivot & double acting hydraulic floor spring type fixing arrangement and making
necessary holes etc. for fixing required door fittings, all complete as per direction
of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
Code Description Unit Quantity Rate Amount
Details of cost for 2.10 sqm
MATERIAL
Glass= 2.10 Sqm.
Add Wastage @ 10% = 0.21 sqm.
Total= 2.31 sqm.
8778 Toughened glass 12 mm thickness sqm 2.31 1750.00 4042.50
9977 Carriage of glass panes and other
materials L.S. 8.19 2.12 17.36
9999 Methylated spirit L.S. 5.33 2.12 11.30
Stainless steel pivot and double acting
hydraulic floor spring type fixing
21.4.1 Rate as per Item No.21.4.1 of
SH:Aluminium Work each 1.00 2448.85 2448.85 A
LABOUR
0119 Glazier day 0.90 714.00 642.60
0114 Beldar day 0.90 645.00 580.50
SUB HEAD : 21- ALUMINIUM WORK 1971
Code Description Unit Quantity Rate Amount
9999 Sundries,sush rog cotton etc. L.S. 1.13 2.12 2.40
TOTAL 7745.51 W
Add 1 % Water charges on "W-A" 52.97
TOTAL 7798.47 X
Add GST on "X-A" (multiplying
factor 0.1405) 751.62
TOTAL 8550.10 Y
Add 15% CPOH on "Y-A" 915.19
TOTAL 9465.28 Z
Add Cess @ 1% on "Z-A" 70.16
Cost for 2.10 sqm 9535.45
Cost for 1 sqm 4540.69
Say 4540.70
21.19 Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/
Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural
non sag elastomeric PU sealant over backer rod of approved quality as per
architectural drawings and direction of Engineer-in-charge complete, complying
to ASTM C920, DIN 18540-F & ISO 11600
21.19.1 Upto 5 mm depth and 5 mm width
Code Description Unit Quantity Rate Amount
Details of cost for 10m length width
5mm & depth 5mm
MATERIAL
2604 Weather/structural non sag elastomeric
PU sealant (600ml Sausage) for joints
in RCC/Brick/ Stone/ wood/ Ceramic/
Gypsum/Alluminium work complying to
ASTM C920, DIN 18540-F & ISO
11600 incl all taxes each 1.00 543.00 543.00
8654 Masking tape metre 20.00 2.18 43.60
9999 Sundries, including charges of Sealant
gun machine, dhoti etc L.S. 26.00 2.12 55.12
9977 Carriage of material L.S. 8.40 2.12 17.81
LABOUR
0123 Mason (brick layer) 1st class day 0.40 784.00 313.60
TOTAL 973.13 W
Add 1 % Water charges on "W" 9.73
TOTAL 982.86 X
Add GST on "X" (multiplying
factor 0.1405) 138.09
TOTAL 1120.95 Y
Add 15% CPOH on "Y" 168.14
TOTAL 1289.09 Z
Add Cess @ 1% on "Z" 12.89
Cost of 10 metre 1301.98
Cost per metre 130.20
Say 130.20
SUB HEAD : 21- ALUMINIUM WORK 1972
21.19.2 Upto 10 mm depth and 10 mm width
Code Description Unit Quantity Rate Amount
Details of cost for 10m length, width
10mm & depth 10mm
MATERIAL
2604 Weather/structural non sag elastomeric
PU sealant (600ml Sausage) for joints
in RCC/Brick/ Stone/ wood/ Ceramic/
Gypsum/Alluminium work complying to
ASTM C920, DIN 18540-F & ISO
11600 incl all taxes each 1.50 543.00 814.50
8654 Masking tape metre 20.00 2.18 43.60
9999 Sundries, including charges of Sealant
gun machine, dhoti etc L.S. 26.00 2.12 55.12
9977 Carriage of material L.S. 8.40 2.12 17.81
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
TOTAL 1323.03 W
Add 1 % Water charges on "W" 13.23
TOTAL 1336.26 X
Add GST on "X" (multiplying
factor 0.1405) 187.74
TOTAL 1524.00 Y
Add 15% CPOH on "Y" 228.60
TOTAL 1752.60 Z
Add Cess @ 1% on "Z" 17.53
Cost of 10 metre 1770.13
Cost per metre 177.01
Say 177.00
21.19.3 Upto 20 mm depth and 20 mm width
Code Description Unit Quantity Rate Amount
Details of cost for 10m length, width
20mm & depth 20mm
MATERIAL
2604 Weather/structural non sag elastomeric
PU sealant (600ml Sausage) for joints
in RCC/Brick/ Stone/ wood/ Ceramic/
Gypsum/Alluminium work complying to
ASTM C920, DIN 18540-F & ISO
11600 incl all taxes each 3.00 543.00 1629.00
8654 Masking tape metre 20.00 2.18 43.60
2630 Baker rod metre 10.00 6.00 60.00
9999 Sundries, including charges of Sealant
gun machine, dhoti etc L.S. 26.00 2.12 55.12
9977 Carriage of material L.S. 8.40 2.12 17.81
SUB HEAD : 21- ALUMINIUM WORK 1973
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 0.75 784.00 588.00
TOTAL 2393.53 W
Add 1 % Water charges on "W" 23.94
TOTAL 2417.46 X
Add GST on "X" (multiplying
factor 0.1405) 339.65
TOTAL 2757.12 Y
Add 15% CPOH on "Y" 413.57
TOTAL 3170.68 Z
Add Cess @ 1% on "Z" 31.71
Cost of 10 metre 3202.39
Cost per metre 320.24
Say 320.25
SUB HEAD : 21- ALUMINIUM WORK 1974
SUB HEAD : 22.0
WATER PROOFING
1975
22.1 Providing and laying integral cement based treatment for water proofing on
horizontal surface at all depth below ground level for under ground structures
as directed by Engineer-in-Charge and consisting of :
(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab
over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand)
mixed with water proofing compound conforming to IS:2645 in the
recommended proportion over the leveling course (leveling course to be paid
separately). Joints sealed and grouted with cement slurry mixed with water
proofing compound.
(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand)
mixed with water proofing compound in recommended proportions.
(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size
spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.
22.1.1 Using rough kota stone.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm
MATERIAL
Ist layer
Cement mortar 1:3 for fixing of stone
10x0.025 = 0.25 cum
3.8 Rate as per Item Number 3.8 of
SH: MORTARS cum 0.25 5024.15 1256.04
Kota stone slab = 10 sqm
Wastage @ 10% = 1 sqm
Total = 11 sqm
1169 Kotastone slab 25mm thick
(rough cheseled) sqm 11.00 250.00 2750.00
Cartage 11x0.025 @ 2330 kg/m3
= 0.64 t
2216 Carriage of Stone blocks white &
red sand stone & kota stone slab tonne 0.64 145.72 93.26
Cement mortar 1:3
10x0.025 = 0.25 cum
Wastage @ 12% = 0.03 cum
Total = 0.28 cum
3.8 Rate as per Item No.3.8 of
SH: MORTARS cum 0.28 5024.15 1406.76
for slurry Bed
2x10.00 @ 2kg/m3 = 40.00 kg
Joints
4x3.7x0.02x0.037 = 0.011 cum
25x0.6x0.02x0.037 = 0.011 cum
= 0.022 cum @ 1440 kg/cum
Total = 71.88 kg or 0. 72 t
0367 Portland Cement (OPC-43 grade) tonne 0.072 5000.00 360.00
2209 Carriage of Cement tonne 0.072 145.72 10.49
Mortar = 0.25 + 0.28 = 0.53 cum
Cement in 0.53 cum @ 5.1 q/cum
= 2.7 quintal
Cement in slurry = 0.73 quintal
Total = 3.43 quintal @ 1 kg for 50 kg
of cement i.e. 6.86 kg
1213 Water proofing materials kilogram 6.86 35.00 240.10
SUB HEAD : 22- WATER PROOFING 1977
Code Description Unit Quantity Rate Amount
0296 Stone Aggregate (Single size) :
12.5 mm nominal size cum 0.08 1350.00 108.00
@ 8 cudm/sqm 1x10.3x8x1/1000
= 0.08 cum
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.08 163.93 13.11
Labour for base mortar & kota stone
laying i/c slurry job
0125 Mason (for plain stone work) 2nd class day 1.20 714.00 856.80
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 1.00 645.00 645.00
LABOUR
Labour for top layer & spreading
stone grit
0125 Mason (for plain stone work) 2nd class day 1.08 714.00 771.12
0114 Beldar day 1.08 645.00 696.60
0101 Bhisti day 0.45 714.00 321.30
9999 Sundries L.S. 6.24 2.12 13.23
TOTAL 10186.82 W
Add 1 % Water charges on "W" 101.87
TOTAL 10288.68 X
Add GST on "X" (multiplying
factor 0.1405) 1445.56
TOTAL 11734.24 Y
Add 15% CPOH on "Y" 1760.14
TOTAL 13494.38 Z
Add Cess @ 1% on "Z" 134.94
Cost for 10.00 sqm 13629.32
Cost for 1 sqm 1362.93
Say 1362.95
22.2 Providing and laying integral cement based treatment for water proofing on
the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with
cement slurry mixed with water proofing compound conforming to IS:2645 in
recommended proportions with a gap of 20 mm (minimum) between stone
slabs and the receiving surfaces and filling the gaps with neat cement slurry
mixed with water proofing compound and finishing the exterior of stone slab
with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat
cement punning mixed with water proofing compound in recommended
proportion complete at all levels and as directed by Engineer-in-charge :
22.2.1 Using rough Kota stone
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm
MATERIAL
Ist layer
Kota stone slab = 10 sqm
Wastage @ 10% = 1 sqm
Total = 11 sqm
SUB HEAD : 22- WATER PROOFING 1978
Code Description Unit Quantity Rate Amount
1169 Kotastone slab 25mm thick (rough
cheseled) sqm 11.00 250.00 2750.00
Cartage 11x0.025 @ 2330 kg/m3
= 0.64t
2216 Carriage of Stone blocks white &
red sand stone & kota stone slab tonne 0.64 145.72 93.26
Cement slurry for jointing
6x3.70 = 22.20 m
7x2.78 = 19.46 m
=41.66x0.025x0.012 = 0.013 cum
Cement slurry for filling 20 mm gap
10x0.02 = 0.200 cum
= 0.213 cum @ 1440 kg/cum
= 306.70 kg or 0.307 t
0367 Portland Cement (OPC-43 grade) tonne 0.31 5000.00 1550.00
2209 Carriage of Cement tonne 0.31 145.72 45.17
Cement plaster 1:3 with neat cement
punning
13.9.2 Rate as per item no 13.9.2 of
SH : Finishing sqm 10.00 507.85 5078.50 A
Water proofing material
Cement slurry = 0.31 t = 310 kg
Cement plaster 1:3 @ 13.62 q/100sqm
= 136.20 kg
Total = 446.20 kg @ 1 kg for 50 kg of
cement i.e. 8.90 kg
1213 Water proofing materials kilogram 8.90 35.00 311.50
LABOUR
Fixing of Kota stone and applying
cement slurry.
0125 Mason (for plain stone work) 2nd class day 3.00 714.00 2142.00
0114 Beldar day 3.00 645.00 1935.00
0115 Coolie day 1.00 645.00 645.00
9999 Sundries and scaffolding L.S. 18.20 2.12 38.58
TOTAL 14589.02 W
Add 1 % Water charges on "W-A" 95.11
TOTAL 14684.12 X
Add GST on "X-A" (multiplying
factor 0.1405) 1349.59
TOTAL 16033.71 Y
Add 15% CPOH on "Y-A" 1643.28
TOTAL 17677.00 Z
Add Cess @ 1% on "Z-A" 125.98
Cost for 10.00sqm 17802.98
Cost for 1 sqm 1780.30
Say 1780.30
22.3 Providing and laying water proofing treatment to vertical and horizontal
surfaces of depressed portions of W.C., kitchen and the like consisting of:
(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing
compound conforming to IS 2645 in recommended proportions including
rounding off junction of vertical and horizontal surface.
SUB HEAD : 22- WATER PROOFING 1979
(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed
with water proofing compound in recommended proportion including rounding
off junction of vertical and horizontal surface.
(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg.
per sqm of area.
(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC
sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/
sqm).
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL
Cement slurry @ 4.4 kg/sqm
= 44.00 kg or 0.044 t
0367 Portland Cement (OPC-43 grade) tonne 0.044 5000.00 220.00
2209 Carriage of Cement tonne 0.044 145.72 6.41
MATERIAL
Cement plaster 1:3 (20 mm thick)
3.8 Rate as per Item No.3.8 of
SH: MORTARS cum 0.224 5024.15 1125.41
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.10 714.00 785.40
9999 Scafolding and sundries L.S. 12.61 2.12 26.73
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.017 34790.00 591.43
= 10x1.70= 17 kg = 0.017 t
2211 Carriage of Tar bitumen tonne 0.017 163.93 2.79
3002 Polyvinyle chloride sheet 400 micron
thick sqm 10.00 45.00 450.00
9977 CARRIAGE L.S. 13.00 2.12 27.56
1213 Water proofing materials kilogram 3.60 35.00 126.00
@ 1 kg per 50 kg of cement used
Cement slurry = 44 kg
Cement plaster 1:3
10x(13.62xl00)/100= 136.2 kg
Total = 180.2 kg/50 = 3.60 kg
LABOUR
0131 Painter day 0.20 714.00 142.80
0114 Beldar day 1.33 645.00 857.85
0130 Mistry day 0.06 784.00 47.04
9999 Sundries L.S. 7.28 2.12 15.43
TOTAL 5786.81 W
Add 1 % Water charges on "W" 57.87
TOTAL 5844.68 X
Add GST on "X" (multiplying
factor 0.1405) 821.18
TOTAL 6665.86 Y
Add 15% CPOH on "Y" 999.88
TOTAL 7665.74 Z
Add Cess @ 1% on "Z" 76.66
Cost for 10 sqm 7742.40
Cost for 1 sqm 774.24
Say 774.25
SUB HEAD : 22- WATER PROOFING 1980
22.4 Providing and Placing in position suitable PVC water stops conforming to
IS:12200 for construction/ expansion joints between two RCC members and
fixed to the reinforcement with binding wire before pouring concrete etc.
complete :
22.4.1 Serrated with central bulb (225 mm wide, 8-11 mm thick)
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7427 Water stops Serrated with central
bulb (225 mm wide, 8-11 mm thick) metre 100.00 200.00 20000.00
LABOUR
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries & wire etc. L.S. 26.00 2.12 55.12
TOTAL 21345.12 W
Add 1 % Water charges on "W" 213.45
TOTAL 21558.57 X
Add GST on "X" (multiplying
factor 0.1405) 3028.98
TOTAL 24587.55 Y
Add 15% CPOH on "Y" 3688.13
TOTAL 28275.68 Z
Add Cess @ 1% on "Z" 282.76
Cost for 100 metres 28558.44
Cost for 1 metre 285.58
Say 285.60
22.4.2 Dumb bell with central bulb (180 mm wide, 8 mm thick)
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7428 Water stops Dumb bell with central bulb metre 100.00 160.00 16000.00
LABOUR
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries & wire etc. L.S. 26.00 2.12 55.12
TOTAL 17345.12 W
Add 1 % Water charges on "W" 173.45
TOTAL 17518.57 X
Add GST on "X" (multiplying
factor 0.1405) 2461.36
TOTAL 19979.93 Y
Add 15% CPOH on "Y" 2996.99
TOTAL 22976.92 Z
Add Cess @ 1% on "Z" 229.77
Cost for 100 metres 23206.69
Cost for 1 metre 232.07
Say 232.05
SUB HEAD : 22- WATER PROOFING 1981
22.4.3 Kickers (320 mm wide, 5 mm thick)
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7429 Kickers metre 100.00 160.00 16000.00
LABOUR
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries & wire etc. L.S. 26.00 2.12 55.12
TOTAL 17345.12 W
Add 1 % Water charges on "W" 173.45
TOTAL 17518.57 X
Add GST on "X" (multiplying
factor 0.1405) 2461.36
TOTAL 19979.93 Y
Add 15% CPOH on "Y" 2996.99
TOTAL 22976.92 Z
Add Cess @ 1% on "Z" 229.77
Cost for 100 metres 23206.69
Cost for 1 metre 232.07
Say 232.05
22.5 Providing and laying water proofing treatment in sunken portion of WCs,
bathroom etc., by applying cement slurry mixed with water proofing cement
compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing
cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4
hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing
cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4
hours followed with water curing for 48 hours.
The rate includes preparation of surface, treatment and sealing of all joints,
corners, junctions of pipes and masonry with polymer mixed slurry.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
Cement 10x(0.488+0.242) = 7.30 kg
Sealing fillets 10x0.5 kg / sqm = 5.00 kg
Total = 12.30 kg = 0.012 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.012 5000.00 60.00
2209 Carriage of Cement tonne 0.012 145.72 1.75
Bonding material 1.6 kgx30x2 = 96 kg
Bitumen (blown/residual type)
10x(0.25+0.126) = 3.79 kg
Sealing fillets 10x0.10 kg / sqm
= 1.00 kg
Wastage @ 5% on 4.79 kg = 0.24 kg
Total = 5.03 kg Say 5.00 kg
8501 Polymer modified cementation coating kilogram 5.00 160.00 800.00
LABOUR
0155 Mason (average) day 2.00 749.00 1498.00
0114 Beldar day 2.00 645.00 1290.00
0101 Bhisti day 0.25 714.00 178.50
SUB HEAD : 22- WATER PROOFING 1982
Code Description Unit Quantity Rate Amount
9999 Sundries, brushes etc L.S. 15.60 2.12 33.07
TOTAL 3861.32 W
Add 1 % Water charges on "W" 38.61
TOTAL 3899.93 X
Add GST on "X" (multiplying
factor 0.1405) 547.94
TOTAL 4447.87 Y
Add 15% CPOH on "Y" 667.18
TOTAL 5115.06 Z
Add Cess @ 1% on "Z" 51.15
Cost for 10 sqm 5166.21
Cost for 1 sqm 516.62
Say 516.60
22.6 Providing and laying water proofing treatment on roofs of slabs by applying
cement slurry mixed with water proofing cement compound consisting of
applying:
(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm
mixed with water proofing cement compound @ 0.253 kg/sqm.
(b) laying second layer of Fibre glass cloth when the first layer is still green.
Overlaps of joints of fibre cloth should not be less than 10 cm.
(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/
sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse
sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by
water curing for 48 hours. The entire treatment will be taken upto 30 cm on
parapet wall and tucked into groove in parapet all around.
(d) fourth and final layer of brick tiling with cement mortar (which will be paid
for separately.
For the purpose of measurement the entire treated surface will be measured.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL
Cement 10x(1.289+0.488) = 17.77 kg
Sealing fillets @ 10% = 1.77 kg
Total = 19.54kg = 0.020 tonne
0367 Portland Cement (OPC-43 grade) tonne 0.02 5000.00 100.00
2209 Carriage of Cement tonne 0.02 145.72 2.91
Bonding material 1.6 kgx30x2 = 96 kg
Bitumen (blown/residual type)
10x(0.253+0.67) = 9.23 kg
Wastage @ 5% = 0.46 kg
Total = 9.69 kg
8501 Polymer modified cementation coating kilogram 9.69 160.00 1550.40
Fibre Glass cloth = 10.00 sqm
Wastage @ 10 % = 1.00 sqm
Total = 11.00 sqm
8502 Fibre glass cloth sqm 11.00 32.00 352.00
LABOUR
0155 Mason (average) day 2.00 749.00 1498.00
0114 Beldar day 1.00 645.00 645.00
SUB HEAD : 22- WATER PROOFING 1983
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.25 714.00 178.50
9999 Sundries, brushes etc L.S. 23.40 2.12 49.61
TOTAL 4376.42 W
Add 1 % Water charges on "W" 43.76
TOTAL 4420.19 X
Add GST on "X" (multiplying
factor 0.1405) 621.04
TOTAL 5041.22 Y
Add 15% CPOH on "Y" 756.18
TOTAL 5797.41 Z
Add Cess @ 1% on "Z" 57.97
Cost for 10 sqm 5855.38
Cost for 1 sqm 585.54
Say 585.55
22.7 Providing and laying integral cement based water proofing treatment including
preparation of surface as required for treatment of roofs, balconies, terraces
etc consisting of following operations:
(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed
with water proofing compound conforming to IS. 2645 and approved by
Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm
height including cleaning the surface before treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115
mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed
with water proofing compound conforming to IS : 2645 and approved by
Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1
cement :5 coarse sand ) admixed with water proofing compound conforming
to IS : 2645 and approved by Engineer-in-charge to required slope and treating
similarly the adjoining walls upto 300 mm height including rounding of junctions
of walls and slabs.
(c) After two days of proper curing applying a second coat of cement slurry
using 2.75 kg/ sqm of cement admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge.
(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4
(1 cement :4 coarse sand) admixed with water proofing compound conforming
to IS : 2645 and approved by Engineer-in-charge including laying glass fibre
cloth of approved quality in top layer of plaster and finally finishing the surface
with trowel with neat cement slurry and making pattern of 300x300 mm square
3 mm deep.
(e) The whole terrace so finished shall be flooded with water for a minimum
period of two weeks for curing and for final test.“All above operations to be
done in order and as directed and specified by the Engineer-in-Charge :
SUB HEAD : 22- WATER PROOFING 1984
22.7.1 With average thickness of 120 mm and minimum thickness at khurra as
65 mm.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
i) Cement slury
0367 Portland Cement (OPC-43 grade) tonne 0.0275 5000.00 137.50
ii) Cement mortar 1:5 (1 cement:
5 coarsesand)
3.10 Rate as per Item No.3.10 of SH:Mortars cum 0.224 3995.00 894.88
iii) Roof treatment with brick bat and
cement mortar
MATERIAL
0285 Brick Aggregate (Single size) : 63 mm cum 0.94 650.00 611.00
2260 Carriage of Brick aggregate cum 0.94 178.19 167.50
Cement mortar 1:5
3.10 Rate as per Item No.3.10 of SH:Mortars cum 0.50 3995.00 1997.50
LABOUR
0114 Beldar day 1.75 645.00 1128.75
0101 Bhisti day 0.28 714.00 199.92
0123 Mason (brick layer) 1st class day 0.05 784.00 39.20
0124 Mason (brick layer) 2nd class day 0.05 714.00 35.70
0128 Mate day 0.04 714.00 28.56
Extra labour for ramming
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 13.65 2.12 28.94
iv) Cement slury
0367 Portland Cement (OPC-43 grade) tonne 0.0275 5000.00 137.50
0114 Beldar day 0.20 645.00 129.00
v) 20 mm cement plaster
1:4 (1 cement : 4 coarse sand)
13.6.1 Rate as per item no 13.6.1 of
SH : Finishing sqm 10.00 421.40 4214.00 A
vi) Water proofing compound
vi) Water proofing compound
27.50+27.50+69.40+124.00
= 248.40 kg @
1 kg per bag of cement
1213 Water proofing materials kilogram 5.00 35.00 175.00
Extra for making chequers for
10 sqm
7233 Fibre glass tissue reinforcement
Type II Grade I sqm 10.50 75.00 787.50
0124 Mason (brick layer) 2nd class day 0.36 714.00 257.04
0114 Beldar day 0.36 645.00 232.20
9999 Chequer plate L.S. 13.65 2.12 28.94
Add labour for laying 20 mm
bed mortar
0124 Mason (brick layer) 2nd class day 0.54 714.00 385.56
0114 Beldar day 0.54 645.00 348.30
SUB HEAD : 22- WATER PROOFING 1985
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.45 714.00 321.30
TOTAL 12447.03 W
Add 1 % Water charges on "W-A" 82.33
TOTAL 12529.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 1168.31
TOTAL 13697.67 Y
Add 15% CPOH on "Y-A" 1422.55
TOTAL 15120.22 Z
Add Cess @ 1% on "Z-A" 109.06
Cost for 10 sqm 15229.29
Cost for one sqm 1522.93
Say 1522.95
22.8 Providing and laying four courses water proofing treatment with bitumen felt
over roofs consisting of first and third courses of blown bitumen 85/25 or 90/
15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for
each course, second course of roofing felt type 3 grade-I (hessian based self
finished bitumen felt) and fourth and final course of stone grit 6 mm and down
size or pea sized gravel spread at 6 cubic decimeter per square metre, including
preparation of surface but excluding grading complete with :
22.8.1 Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
Blown or / and residual bitumen
applied hot = 2x1.45x30 = 87 kg
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.087 34790.00 3026.73
Hession felt type 3 Grade I (hessian
base self finished bitumen felt) =
30sqm + Add for over lapping @ 10%
= 3 sqm. Total = 33 Sqm
0322 Bitumen felt :Type 3 grade 1 sqm 33.00 70.00 2310.00
1177 Stone grit 6 mm and down size or
pea sized gravel cum 0.18 800.00 144.00
30x6=180 cudm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.18 163.93 29.51
2211 Carriage of Tar bitumen tonne 0.162 163.93 26.56
0.087tx2.7x.001x33=0.162t
0370 Coal (steam) quintal 0.174 440.00 76.56
= 2 quintals/t of bitumen i.e. 2x0.087
=0.174q
2200 Carriage of steam coal tonne 0.0174 187.35 3.26
9999 Praparing roof surface, sutting groove
and making good etc. L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 2.16 714.00 1542.24
0114 Beldar day 3.24 645.00 2089.80
0130 Mistry day 0.18 784.00 141.12
SUB HEAD : 22- WATER PROOFING 1986
Code Description Unit Quantity Rate Amount
9999 Sundries, brushes etc. L.S. 6.76 2.12 14.33
TOTAL 9689.35 W
Add 1 % Water charges on "W" 96.89
TOTAL 9786.24 X
Add GST on "X" (multiplying
factor 0.1405) 1374.97
TOTAL 11161.21 Y
Add 15% CPOH on "Y" 1674.18
TOTAL 12835.39 Z
Add Cess @ 1% on "Z" 128.35
Cost of 30.00 Sqm. 12963.75
Cost of 1.00 Sqm. 432.12
Say 432.10
22.9 Providing and laying six courses water proofing treatment with bitumen felt
over roofs consisting of first, third and fifth course of blown bitumen 85/25 or
90/15 conforming to IS : 702 applied hot @ 1.45, 1.20 and 1.45 Kg per square
metre of area respectively, second and fourth courses of roofing felt type 3
grade I conforming to IS : 1322 (Hessian based self finished bitumen felt) ,
sixth and final course of stone grit 6 mm and down size or pea sized gravel
spread at 6 cubic decimeter per sqm including preparation of surface but
excluding grading, complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
Blown or / and residual bitumen
applied hot
(1.45+1.20+1.45)x30=123kg
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.123 34790.00 4279.17
Bitumen felt Type 3 grade 1 (hessian
base self finished bitumen felt) = 60
sqm.+ Add for over lapping @ 10%
= 6 sqm. Total =66 Sqm
0322 Bitumen felt :Type 3 grade 1 sqm 66.00 70.00 4620.00
2211 Carriage of Tar bitumen tonne 0.273 163.93 44.75
0.123t+2.7x.001x66=0.273t
1177 Stone grit 6 mm and down size or
pea sized gravel cum 0.18 800.00 144.00
30x6=180cudm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.18 163.93 29.51
0370 Coal (steam) quintal 0.246 440.00 108.24
= 2 quintals/t of bitumen i.e. 2x0.123
=0.246q
2200 Carriage of steam coal tonne 0.0246 187.35 4.61
9999 Praparing roof surface, sutting groove
and making good etc. L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 3.24 714.00 2313.36
0114 Beldar day 4.86 645.00 3134.70
0130 Mistry day 0.2 784.00 156.80
SUB HEAD : 22- WATER PROOFING 1987
Code Description Unit Quantity Rate Amount
9999 Sundries, brushes etc. L.S. 6.76 2.12 14.33
TOTAL 15134.72 W
Add 1 % Water charges on "W" 151.35
TOTAL 15286.06 X
Add GST on "X" (multiplying
factor 0.1405) 2147.69
TOTAL 17433.76 Y
Add 15% CPOH on "Y" 2615.06
TOTAL 20048.82 Z
Add Cess @ 1% on "Z" 200.49
Cost of 30.00 Sqm. 20249.31
Cost of 1.00 Sqm. 674.98
Say 675.00
22.10 Providing and laying six courses water proofing treatment with bitumen felt
over roofs consisting of first, third and fifth courses of blown or / and residual
bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area
respectively, second and fourth courses of roofing felt type 2 grade I (fibre
base self finished bitumen felt) six and final courses of stone grit 6 mm and
down size or pea sized gravel spread at 6 cubic decimeter per sqm including
preparation of surface, excluding grading, compete.
Code Description Unit Quantity Rate Amount
Details of cost for 30 sqm
Blown bitumen applied hot
(1.45+1.20+1.70)x30 = 130.5 kg.
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.1305 34790.00 4540.10
Bitumen felt type B grade I (fibre base
self finished bitumen felt) = 60 sqm. +
Add for over lapping @ 10% = 6 sqm.
Total =66 Sqm
0318 Bitumen felt fibre base (vegetable or
animal):Type 2 grade 1 sqm 66.00 70.00 4620.00
2211 Carriage of Tar bitumen tonne 0.275 163.93 45.08
(0.131 t+2.22x.001x66 = 0.275t)
1177 Stone grit 6 mm and down size or
pea sized gravel cum 0.18 800.00 144.00
30x6=180cudm
CARRIAGE:
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.18 163.93 29.51
Fuel (Steam coal) = 2 quintals/t of
bitumen i.e. 0.1305=0.261q
0370 Coal (steam) quintal 0.261 440.00 114.84
2200 Carriage of steam coal tonne 0.0261 187.35 4.89
9999 Praparing roof surface, sutting groove
and making good etc. L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 4.32 714.00 3084.48
0114 Beldar day 6.48 645.00 4179.60
0130 Mistry day 0.36 784.00 282.24
SUB HEAD : 22- WATER PROOFING 1988
Code Description Unit Quantity Rate Amount
9999 Sundries, brushes etc. L.S. 6.76 2.12 14.33
TOTAL 17344.31 W
Add 1 % Water charges on "W" 173.44
TOTAL 17517.75 X
Add GST on "X" (multiplying
factor 0.1405) 2461.24
TOTAL 19979.00 Y
Add 15% CPOH on "Y" 2996.85
TOTAL 22975.85 Z
Add Cess @ 1% on "Z" 229.76
Cost of 30.00 Sqm. 23205.61
Cost of 1.00 Sqm. 773.52
Say 773.50
22.11 Providing and laying six courses water proofing treatment with bitumen felt
over roofs consisting of first, third and fifth courses of blown or / and residual
bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area
respectively, second and fourth courses of roofing felt type 2 grade II (glass
fibre base self finished bitumen felt) and sixth and final course of stone grit 6
mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm
including preparation of surface but excluding grading, complete.
Code Description Unit Quantity Rate Amount
Detail of cost for 30 sqm
Blown or / and residual bitumen applied
hot (1.45+1.20+1.70)x30 =130.5 kg.
0313 Blown type petroleum bitumen of
penetration 85/25 of approved quality tonne 0.1305 34790.00 4540.10
Bitumen felt as per IS 7193 Grade II
(fibre base self finished bitumen felt) =
60 sqm. + Add for over lapping @ 10%
= 6 sqm. Total =66 Sqm
0318 Bitumen felt fibre base (vegetable or
animal):As per IS 7193 Grade I sqm 66.00 70.00 4620.00
2211 Carriage of Tar bitumen tonne 0.334 163.93 54.75
(0.131t+3.08x.001x66=334t.)
1177 Stone grit 6 mm and down size or
pea sized gravel cum 0.18 800.00 144.00
30x6=180cudm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.18 163.93 29.51
Fuel (Steam coal) = 2 quintals/t of
bitumen
i.e. 2x0.1305=0.261q
0370 Coal (steam) quintal 0.261 440.00 114.84
2200 Carriage of steam coal tonne 0.0261 187.35 4.89
9999 Praparing roof surface, sutting groove
and making good etc. L.S. 134.55 2.12 285.25
LABOUR
0131 Painter day 4.32 714.00 3084.48
0114 Beldar day 6.48 645.00 4179.60
0130 Mistry day 0.36 784.00 282.24
SUB HEAD : 22- WATER PROOFING 1989
Code Description Unit Quantity Rate Amount
9999 Sundries, brushes etc. L.S. 6.76 2.12 14.33
TOTAL 17353.98 W
Add 1 % Water charges on "W" 173.54
TOTAL 17527.52 X
Add GST on "X" (multiplying
factor 0.1405) 2462.62
TOTAL 19990.14 Y
Add 15% CPOH on "Y" 2998.52
TOTAL 22988.66 Z
Add Cess @ 1% on "Z" 229.89
Cost of 30.00 Sqm. 23218.55
Cost of 1.00 Sqm. 773.95
Say 773.95
22.12 Supplying and applying bituminous solution primer on roof and / or wall
surface at 0.24 litre per sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sq. metres
MATERIAL
0316 Bitumen solution primer of approved
quality litre 2.40 47.00 112.80
9977 CARRIAGE L.S. 1.43 2.12 3.03
LABOUR
0131 Painter day 0.17 714.00 121.38
0114 Beldar day 0.17 645.00 109.65
9999 Sundries brushes etc. L.S. 13.52 2.12 28.66
TOTAL 375.52 W
Add 1 % Water charges on "W" 3.76
TOTAL 379.28 X
Add GST on "X" (multiplying
factor 0.1405) 53.29
TOTAL 432.57 Y
Add 15% CPOH on "Y" 64.89
TOTAL 497.45 Z
Add Cess @ 1% on "Z" 4.97
Cost of 10.00 Sqm. 502.43
Cost of 1.00 Sqm. 50.24
Say 50.25
22.13 Deduct for omitting in water proofing treatment final course of spreading stone
grit 6 mm down size or pea sized gravel :
22.13.1 at 6 cudm per sqm
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
1177 Stone grit 6 mm and down size or
pea sized gravel cum 0.06 800.00 48.00
6x10 = 60 cudm
SUB HEAD : 22- WATER PROOFING 1990
Code Description Unit Quantity Rate Amount
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.06 163.93 9.84
9999 Labour for screening and spreading grit L.S. 21.58 2.12 45.75
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 117.92 W
Add 1 % Water charges on "W" 1.18
TOTAL 119.10 X
Add GST on "X" (multiplying
factor 0.1405) 16.73
TOTAL 135.83 Y
Add 15% CPOH on "Y" 20.37
TOTAL 156.20 Z
Add Cess @ 1% on "Z" 1.56
Cost of 10.00 Sqm. 157.77
Cost of 1.00 Sqm. 15.78
Say 15.80
22.13.2 at 8 cudm per sqm
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm.
MATERIAL
1177 Stone grit 8 mm and down size or
pea sized gravel cum 0.08 800.00 64.00
8x10 = 80 cudm
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.08 163.93 13.11
9999 Labour for screening and spreading grit L.S. 26.91 2.12 57.05
9999 Sundries L.S. 6.76 2.12 14.33
TOTAL 148.49 W
Add 1 % Water charges on "W" 1.48
TOTAL 149.98 X
Add GST on "X" (multiplying
factor 0.1405) 21.07
TOTAL 171.05 Y
Add 15% CPOH on "Y" 25.66
TOTAL 196.71 Z
Add Cess @ 1% on "Z" 1.97
Cost of 10.00 Sqm. 198.68
Cost of 1.00 Sqm. 19.87
Say 19.85
22.14 Grading roof for water proofing treatment with
22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size)
Code Description Unit Quantity Rate Amount
Details of cost for one cum.
0295 Stone Aggregate (Single size) :
20 mm nominal size cum 0.67 1400.00 938.00
SUB HEAD : 22- WATER PROOFING 1991
Code Description Unit Quantity Rate Amount
0297 Stone Aggregate (Single size) :
10 mm nominal size cum 0.22 1350.00 297.00
2202 Carriage of Stone aggregate below
40 mm nominal size cum 0.89 163.93 145.90
0982 Coarse sand (zone III) cum 0.45 1500.00 675.00
2203 Carriage of Coarse sand cum 0.45 163.93 73.77
0367 Portland Cement (OPC-43 grade) tonne 0.32 5000.00 1600.00
2209 Carriage of Cement tonne 0.32 145.72 46.63
LABOUR
0114 Beldar day 1.63 645.00 1051.35
0101 Bhisti day 0.70 714.00 499.80
0123 Mason (brick layer) 1st class day 0.10 784.00 78.40
9999 Sundries, brushes etc. L.S. 14.30 2.12 30.32
0002 Hire charges of Concrete Mixer 0.25 to
0.40 cum with hooper day 0.07 800.00 56.00
0012 Vibrator (Needle type 40 mm) day 0.07 350.00 24.50
9999 Sundries for laying in terrace L.S. 45.76 2.12 97.01
TOTAL 5613.67 W
Add 1 % Water charges on "W" 56.14
TOTAL 5669.81 X
Add GST on "X" (multiplying
factor 0.1405) 796.61
TOTAL 6466.42 Y
Add 15% CPOH on "Y" 969.96
TOTAL 7436.38 Z
Add Cess @ 1% on "Z" 74.36
Cost of one cum 7510.75
Say 7510.75
22.14.2 Cement mortar 1:3 (1 cement : 3 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for one cum.
MATERIAL
Cement mortar 1:3
3.8 Rate as per Item No.3.8 of SH:Mortars cum 1.00 5024.15 5024.15
LABOUR
0155 Mason (average) day 1.00 749.00 749.00
0114 Beldar day 2.00 645.00 1290.00
0101 Bhisti day 0.50 714.00 357.00
0115 Coolie day 5.00 645.00 3225.00
9999 Sundries L.S. 11.70 2.12 24.80
TOTAL 10669.95 W
Add 1 % Water charges on "W" 106.70
TOTAL 10776.65 X
Add GST on "X" (multiplying
factor 0.1405) 1514.12
TOTAL 12290.77 Y
Add 15% CPOH on "Y" 1843.62
TOTAL 14134.39 Z
Add Cess @ 1% on "Z" 141.34
Cost of one cum 14275.73
Say 14275.75
SUB HEAD : 22- WATER PROOFING 1992
22.14.3 Cement mortar 1:4 (1cement : 4 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for one cum.
MATERIAL
Cement mortar 1:4
3.9 Rate as per Item Number 3.9 of
SH: Mortars cum 1.00 4355.20 4355.20
LABOUR
0155 Mason (average) day 1.00 749.00 749.00
0114 Beldar day 2.00 645.00 1290.00
0101 Bhisti day 0.50 714.00 357.00
0115 Coolie day 5.00 645.00 3225.00
9999 Sundries L.S. 10.79 2.12 22.87
TOTAL 9999.07 W
Add 1 % Water charges on "W" 99.99
TOTAL 10099.07 X
Add GST on "X" (multiplying
factor 0.1405) 1418.92
TOTAL 11517.98 Y
Add 15% CPOH on "Y" 1727.70
TOTAL 13245.68 Z
Add Cess @ 1% on "Z" 132.46
Cost of one cum 13378.14
Say 13378.15
22.22 Providing and mixing integral crystalline admixture for water proofing
treatment to RCC structures like basement raft, retaining walls, reservior,
sewage & water treatment plant, tunnels / subway and bridge deck etc. at the
time of transporting of concrete into the drum of the ready-mix truck , using
integral crystalline admixture @0.80% (minimum) to the weight of cement
content per cubic meter of concrete) or higher as recommended by the
manufacturer's specification in reinforced cement concrete at site of work.
The material shall meet the requirements as specified in ACI-212-3R-2010 i.e.
by reducing permeability of concrete by more than 90%, compared with control
concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The
crystalline admixture shall be capable of self-healing of cracks up to a width
of 0.50mm. The work shall be carried out all complete as per specification and
the direction of the Engineer-in-charge. The product performance shall carry
guarantee for 10 years against any leakage.
Code Description Unit Quantity Rate Amount
Details of cost for 1 kg
MATERIAL :
0352 Integral crystalline admixture kg 1.00 230.00 230.00
LABOUR :
9999 For measuring, making and mixing etc.. L.S. 5.80 2.12 12.30
9999 Sundries L.S. 1.15 2.12 2.44
SUB HEAD : 22- WATER PROOFING 1993
Code Description Unit Quantity Rate Amount
9999 Carriage of material and tools cost etc.. L.S. 1.75 2.12 3.71
TOTAL 248.44 W
Add 1 % Water charges on "W" 2.48
TOTAL 250.93 X
Add GST on "X" (multiplying
factor 0.1405) 35.26
TOTAL 286.18 Y
Add 15% CPOH on "Y" 42.93
TOTAL 329.11 Z
Add Cess @ 1% on "Z" 3.29
Cost for 1.00 Kg 332.40
Say 332.40
22.22A Providing and applying fibre reinforced elastomeric liquid water proofing
membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI)
of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of
self-priming of elastomeric waterproofing liquid (dilution with water in the
ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry
film thickness of complete application/system not less than 500 microns). The
operation shall be carried out after scrapping and properly cleaning the surface
to remove loose particles with wire brushes, complete in all respect as per the
direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8511 Fibre reinforced elastomeric liquid water
proofing membrane litre 11.30 230.00 2599.00
10.76 litre + 0.538 (Add wastage 5%)
= 11.30 litre
9977 Carriage of materials L.S. 1.43 2.12 3.03
LABOUR
0115 Coolie day 0.67 645.00 432.15
0131 Painter day 0.67 714.00 478.38
9999 Wire brush brushes, rollers etc. L.S. 6.76 2.12 14.33
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 3543.98 W
Add 1 % Water charges on "W" 35.44
TOTAL 3579.42 X
Add GST on "X" (multiplying
factor 0.1405) 502.91
TOTAL 4082.33 Y
Add 15% CPOH on "Y" 612.35
TOTAL 4694.68 Z
Add Cess @ 1% on "Z" 46.95
Cost of 10 sqm 4741.62
Cost of 1 sqm 474.16
Say 474.15
SUB HEAD : 22- WATER PROOFING 1994
22.23 Providing and applying integral crystalline slurry of hydrophilic in nature for
waterproofing treatment to the RCC structures like retaining walls of the
basement, water tanks, roof slabs, podiums, reservior, sewage & water
treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in
the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical
surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal
surfaces and applying the same from negative (internal) side with the help of
synthetic fiber brush. The material shall meet the requirements as specified in
ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90%
compared with control concrete as per DIN 1048 and resistant to 16 bar
hydrostatic pressure on negative side. The crystalline slurry shall be capable
of self-healing of cracks up to a width of 0.50mm. The work shall be carried
out all complete as per specification and the direction of the engineer-in-
charge. The product performance shall carry guarantee for 10 years against
any leakage.
22.23.1 For vertical surface two coats @ 0.70 kg per sqm
Code Description Unit Quantity Rate Amount
Details of cost for 1 sqm
MATERIAL :
0351 Integral crystalline slurry kg 1.40 195.00 273.00
(2 x .70kg / sq.mtr. = 1.40kg)
LABOUR
9999 For application of waterproofing material L.S. 11.55 2.12 24.49
9999 Sundries L.S. 1.15 2.12 2.44
9999 Carriage of material and tools cost etc.. L.S. 1.75 2.12 3.71
TOTAL 303.63 W
Add 1 % Water charges on "W" 3.04
TOTAL 306.67 X
Add GST on "X" (multiplying
factor 0.1405) 43.09
TOTAL 349.76 Y
Add 15% CPOH on "Y" 52.46
TOTAL 402.22 Z
Add Cess @ 1% on "Z" 4.02
Cost for 1.00 sqm 406.24
Say 406.25
22.23.2 For horizontal surface one coat @1.10 kg per sqm.
Code Description Unit Quantity Rate Amount
Details of cost for 1 sqm
MATERIAL :
0351 Integral crystalline slurry kilogram 1.10 195.00 214.50
(1 x 1.10kg / sq.mtr. = 1.10kg)
LABOUR :
9999 For application of waterproofing material L.S. 5.75 2.12 12.19
9999 Sundries L.S. 1.15 2.12 2.44
SUB HEAD : 22- WATER PROOFING 1995
Code Description Unit Quantity Rate Amount
9999 Carriage of material and tools cost etc.. L.S. 1.75 2.12 3.71
TOTAL 232.84 W
Add 1 % Water charges on "W" 2.33
TOTAL 235.17 X
Add GST on "X" (multiplying
factor 0.1405) 33.04
TOTAL 268.21 Y
Add 15% CPOH on "Y" 40.23
TOTAL 308.44 Z
Add Cess @ 1% on "Z" 3.08
Cost for 1.00 sqm 311.52
Say 311.50
22.23A Providing & Applying polymer modified, flexible cementatious negative side
waterproofing coating with elastic waterproofing polymers on interior wall
plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of
cementatious waterproofing polymer(dilution with water in the ratio of 1:1)
and two coats of cementatious waterproofing polymer (dilution with water in
the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove
pre-existing paint film & loose particles till plaster is visible, complete in all
respect as per the direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8512 Cementitious water proofing coating
with elastic polymers kg 15.07 225.00 3390.75
14.35 kg + 0.72 (Add wastage 5%)
= 15.07 litre
9977 Carriage of materials L.S. 1.56 2.12 3.31
LABOUR
0115 Coolie day 0.23 645.00 148.35
0131 Painter day 0.46 714.00 328.44
9999 Wire brush brushes, rollers etc. L.S. 7.15 2.12 15.16
9999 Sundries L.S. 8.06 2.12 17.09
TOTAL 3903.09 W
Add 1 % Water charges on "W" 39.03
TOTAL 3942.12 X
Add GST on "X" (multiplying
factor 0.1405) 553.87
TOTAL 4495.99 Y
Add 15% CPOH on "Y" 674.40
TOTAL 5170.39 Z
Add Cess @ 1% on "Z" 51.70
Cost of 10 sqm 5222.09
Cost of 1 sqm 522.21
Say 522.20
SUB HEAD : 22- WATER PROOFING 1996
22.24 Providing and applying integral crystalline (dry shake) of hydrophilic in nature
for waterproofing treatment to the RCC structures like basement raft,
foundation slab, sewage & water treatment plant slab, warehouses floor,
parking structures and water tank base slab etc. sprinkled @0.60kg per sqm
or higher as recommended by the manufacturer's specification over the lean
concrete of above cited structures. The material shall meet the requirements
as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by
more than 85%, compared control concrete as per DIN 1048 and resistant to
16 bar hydrostatic pressure on negative side. The crystalline dry-shake shall
be capable of self-healing of cracks up to a width of 0.50mm. The work shall
be carried out all complete as per specification and the direction of the
Engineer-in-charge. The product performance shall carry guarantee for 10
years against any leakage.
Code Description Unit Quantity Rate Amount
Details of cost for 1 sqm
MATERIAL :
0354 Integral crystalline dry shake kilogram 0.60 280.00 168.00
LABOUR
9999 For measuring and sprinkling of
waterproofing material L.S. 11.55 2.12 24.49
9999 Sundries L.S. 1.15 2.12 2.44
9999 Carriage of material and tools cost etc.. L.S. 1.75 2.12 3.71
TOTAL 198.63 W
Add 1 % Water charges on "W" 1.99
TOTAL 200.62 X
Add GST on "X" (multiplying
factor 0.1405) 28.19
TOTAL 228.81 Y
Add 15% CPOH on "Y" 34.32
TOTAL 263.13 Z
Add Cess @ 1% on "Z" 2.63
Cost for 1.00 sqm 265.76
Say 265.75
22.24A Providing & Applying high quality acrylic modified resin based texture of
Dholpur/Red sand stone Pattern with anti algae and UV resistance properties
to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to
form film of 1- 1.5 mm thickness after scrapping and properly cleaning the
surface to remove loose particles from the plaster surface, followed by top
coating with Premium Acrylic Smooth exterior paint with Silicone additives
of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the
direction of Engineer -in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8513 Acrylic modified resin based texture kg 45.19 42.00 1897.98
43.04 kg + 2.15 (Add wastage 5%)
= 45.19 kg
SUB HEAD : 22- WATER PROOFING 1997
Code Description Unit Quantity Rate Amount
Quantity taken for cost using once
= 10 sqm
Top coat with premium acrylic exterior
paint (two or more coats)
13.112.1 Rate as per Item No.13.112.1 of
SH:Finishing sqm 10.00 108.60 1086.00 A
9977 Carriage of materials L.S. 3.90 2.12 8.27
LABOUR
0115 Coolie day 0.56 645.00 361.20
0123 Mason (brick layer) 1st class day 0.56 784.00 439.04
9999 Sundries and scaffolding L.S. 40.00 2.12 84.80
TOTAL 3877.29 W
Add 1 % Water charges on "W-A" 27.91
TOTAL 3905.20 X
Add GST on "X-A" (multiplying
factor 0.1405) 396.10
TOTAL 4301.30 Y
Add 15% CPOH on "Y-A" 482.29
TOTAL 4783.59 Z
Add Cess @ 1% on "Z-A" 36.98
Cost of 10 sqm 4820.57
Cost of 1 sqm 482.06
Say 482.05
22.25 Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5
parts crystalline mortar : 1 part water) for the treatment of faulty construction
joints, cracks, tie rod holes and spalled & honeycombed surface of RCC
underground structures like basement, water tanks, bridge deck etc. to ensure
water tightness. The crystallie mortar shall conform to the EN 1504-3 having
compressive strength Class R4 ?45 MPa and adhesive bond strength Class
R3 ?1.5 MPa. The work shall be carried out all complete as per specification
and the direction of the Engineer-In-Charge. The product performance shall
carry guarantee for 10 years against any leakage.
22.25.1 For sealing cracks and faulty construction joints, routed out/making U-shape
groove size 25x25mm and then primed the area with integral crystalline slurry
@0.05kg/running metre and while the surface is tacky filled the groove upto
surface with crystalline mortar @1.50kg/running metre. Once crystalline
mortar is touch dry then finally applied two coats of integral crystalline slurry
@0.05kg/running metre per coat.
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 meter
MATERIAL :
0353 Crystalline Mortar @1.50 kg per meter kilogram 1.50 190.00 285.00
0351 Integral crystalline slurry for priming
and finishing kilogram 0.150 195.00 29.25
(3 x 0.05kg / meter) = 0.15kg
LABOUR
9999 For making crystalline mortar and
repair work etc.. L.S. 14.450 2.12 30.63
9999 Sundries L.S. 1.150 2.12 2.44
SUB HEAD : 22- WATER PROOFING 1998
Code Description Unit Quantity Rate Amount
9999 Carriage of material and tools cost etc.. L.S. 1.750 2.12 3.71
TOTAL 351.03 W
Add 1 % Water charges on "W" 3.51
TOTAL 354.54 X
Add GST on "X" (multiplying
factor 0.1405) 49.81
TOTAL 404.36 Y
Add 15% CPOH on "Y" 60.65
TOTAL 465.01 Z
Add Cess @ 1% on "Z" 4.65
Cost for 1.00 meter 469.66
Say 469.65
22.25.2 For patching of tie rod holes, prepared tie rod hole surface and then primed
the area with integral crystalline slurry @0.070kg/sqm and while the surface
is tacky repair and then filled the tie rod holes with crystalline [email protected]
per hole. The crystalline mortar should be tightly rodded into tie rod holes or
packed tightly (For 25x25x25 mm tie rod hole, use 0.040kg to fill the hole)
Code Description Unit Quantity Rate Amount
Details of cost for 1 no. hole
MATERIAL :
0353 Crystalline [email protected] kg per hole kilogram 0.04 190.00 7.60
LABOUR
9999 For making crystalline mortar and
repair work etc.. L.S. 2.90 2.12 6.15
9999 Sundries L.S. 0.30 2.12 0.64
9999 Carriage of material and tools cost etc.. L.S. 0.25 2.12 0.53
TOTAL 14.91 W
Add 1 % Water charges on "W" 0.15
TOTAL 15.06 X
Add GST on "X" (multiplying
factor 0.1405) 2.12
TOTAL 17.18 Y
Add 15% CPOH on "Y" 2.58
TOTAL 19.76 Z
Add Cess @ 1% on "Z" 0.20
Cost for each hole 19.95
Say 19.95
22.26 Providing and applying of swellable type water stop tape, 19mm x 25mm thick
in linear meter (expansive nature) for construction joints treatment of RCC
structure such as raft slab, retaining walls, water storage tank and at the
junctions of raft slab with the retaining walls etc.. After cleaning the surface,
one coat of required primer for swellable water stop tape shall be applied
throughout the length of the joint @3.78 litre per 240 running meter. Over the
primed surface swellable type water stop tape shall be placed. The work shall
SUB HEAD : 22- WATER PROOFING 1999
be carried out all complete as per specification and the direction of the
Engineer-In-Charge. The product performance shall carry guarantee for 10
years against any leakage.
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 meter
MATERIAL :
0355 Swellable type water stop tape
(Crystalline sealing compound) metre 1.00 325.00 325.00
0356 Swellable type water stop primer Litre 0.016 1300.00 20.80
(@3.78 litre per 240 running meter)
LABOUR
9999 For application of primer and swellable
water stop L.S. 8.65 2.12 18.34
9999 Sundries L.S. 1.15 2.12 2.44
9999 Carriage of material and tools cost etc.. L.S. 1.75 2.12 3.71
TOTAL 370.29 W
Add 1 % Water charges on "W" 3.70
TOTAL 373.99 X
Add GST on "X" (multiplying
factor 0.1405) 52.55
TOTAL 426.53 Y
Add 15% CPOH on "Y" 63.98
TOTAL 490.51 Z
Add Cess @ 1% on "Z" 4.91
Cost for 1.00 metre 495.42
Say 495.40
SUB HEAD : 22- WATER PROOFING 2000
SUB HEAD : 23.0
RAIN WATER HARVESTING &
TUBEWELLS
2001
23.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method
prescribed in IS: 2800 (part I), including collecting samples from different strata,
preparing and submitting strata chart/ bore log, including hire & running charges
of all equipments, tools, plants & machineries required for the job, all complete as
per direction of Engineer-in-charge, upto 90 metre depth below ground level.
23.1.1 All types of soil
23.1.1.1 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 35 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 1.00 7000.00 7000.00
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro
to site
(assume 140m of bore for one shifting)
(2x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0114 Beldar day 2.00 645.00 1290.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 35 metre 20721.56
Cost of 1 metre 592.04
Say 592.05
23.1.1.2 350 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 32 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with
driver and fuel. day 1.00 7000.00 7000.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2003
Code Description Unit Quantity Rate Amount
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0114 Beldar day 2.00 645.00 1290.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 32 metre 20721.56
Cost of 1 metre 647.55
Say 647.55
23.1.1.3 400 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 25 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with
driver and fuel. day 1.00 7000.00 7000.00
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator
& security
0114 Beldar day 2.00 645.00 1290.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2004
Code Description Unit Quantity Rate Amount
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 25 metre 20721.56
Cost of 1 metre 828.86
Say 828.85
23.1.2 Rocky strata including Boulders
23.1.2.1 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 16 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with
driver and fuel. day 0.90 7000.00 6300.00
1235 Diesel oil litre 6.00 80.87 485.22
Extra diesel required for boring in
rocky strata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator
& security
0134 Rock Hole Driller day 0.75 645.00 483.75
0114 Beldar day 3.00 645.00 1935.00
0103 Blacksmith 2nd class day 0.75 714.00 535.50
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 16937.15 W
Add 1 % Water charges on "W" 169.37
TOTAL 17106.53 X
Add GST on "X" (multiplying
factor 0.1405) 2403.47
TOTAL 19509.99 Y
Add 15% CPOH on "Y" 2926.50
TOTAL 22436.49 Z
Add Cess @ 1% on "Z" 224.36
Cost for 16 metre 22660.86
Cost of 1 metre 1416.30
Say 1416.30
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2005
23.1.2.2 350 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 16 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with
driver and fuel. day 0.90 7000.00 6300.00
1235 Diesel oil litre 8.00 80.87 646.96
Extra diesel required for boring in
rockystrata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator
&security
0134 Rock Hole Driller day 1.00 645.00 645.00
0114 Beldar day 4.00 645.00 2580.00
0103 Blacksmith 2nd class day 0.75 714.00 535.50
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 17905.14 W
Add 1 % Water charges on "W" 179.05
TOTAL 18084.20 X
Add GST on "X" (multiplying
factor 0.1405) 2540.83
TOTAL 20625.02 Y
Add 15% CPOH on "Y" 3093.75
TOTAL 23718.78 Z
Add Cess @ 1% on "Z" 237.19
Cost for 16 metre 23955.97
Cost of 1 metre 1497.25
Say 1497.25
23.1.2.3 400 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 16 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 0.90 7000.00 6300.00
1235 Diesel oil litre 16.00 80.87 1293.92
Extra diesel required for boring in
rockystrata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro
to site
(assume 140m of bore for one shifting)
(2x30)/140
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2006
Code Description Unit Quantity Rate Amount
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0134 Rock Hole Driller day 1.20 645.00 774.00
0114 Beldar day 8.00 645.00 5160.00
0103 Blacksmith 2nd class day 0.75 714.00 535.50
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 21261.10 W
Add 1 % Water charges on "W" 212.61
TOTAL 21473.72 X
Add GST on "X" (multiplying
factor 0.1405) 3017.06
TOTAL 24490.77 Y
Add 15% CPOH on "Y" 3673.62
TOTAL 28164.39 Z
Add Cess @ 1% on "Z" 281.64
Cost for 16 metre 28446.03
Cost of 1 metre 1777.88
Say 1777.90
23.2 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method
prescribed in IS: 2800 (part I), including collecting samples from different strata,
preparing and submitting strata chart/ bore log, including hire & running charges
of all equipments, tools, plants & machineries required for the job, all complete as
per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below
ground level.
23.2.1 All types of soil
23.2.1.1 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 1.00 7000.00 7000.00
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2007
Code Description Unit Quantity Rate Amount
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0114 Beldar day 2.00 645.00 1290.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 30 metre 20721.56
Cost of 1 metre 690.72
Say 690.70
23.2.1.2 350 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 27 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 1.00 7000.00 7000.00
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro
to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0114 Beldar day 2.00 645.00 1290.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 27 metre 20721.56
Cost of 1 metre 767.47
Say 767.45
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2008
23.2.1.3 400 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 20 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 1.00 7000.00 7000.00
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro
to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0114 Beldar day 2.00 645.00 1290.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 15487.68 W
Add 1 % Water charges on "W" 154.88
TOTAL 15642.56 X
Add GST on "X" (multiplying
factor 0.1405) 2197.78
TOTAL 17840.34 Y
Add 15% CPOH on "Y" 2676.05
TOTAL 20516.39 Z
Add Cess @ 1% on "Z" 205.16
Cost for 20 metre 20721.56
Cost of 1 metre 1036.08
Say 1036.10
23.2.2 Rocky strata including Boulders
23.2.2.1 300 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 16 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 0.90 7000.00 6300.00
1235 Diesel oil litre 10.00 80.87 808.70
Extra diesel required for boring in
rockystrata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro to
site (assume 140m of bore for one
shifting) (2 x30)/140Loading, unloading
&Errection charges of drilling Rig
Machine
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2009
Code Description Unit Quantity Rate Amount
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0134 Rock Hole Driller day 1.00 645.00 645.00
0114 Beldar day 5.00 645.00 3225.00
0103 Blacksmith 2nd class day 0.70 714.00 499.80
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 18676.18 W
Add 1 % Water charges on "W" 186.76
TOTAL 18862.95 X
Add GST on "X" (multiplying
factor 0.1405) 2650.24
TOTAL 21513.19 Y
Add 15% CPOH on "Y" 3226.98
TOTAL 24740.17 Z
Add Cess @ 1% on "Z" 247.40
Cost for 16 metre 24987.57
Cost of 1 metre 1561.72
Say 1561.70
23.2.2.2 350 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 16 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 0.90 7000.00 6300.00
1235 Diesel oil litre 12.00 80.87 970.44
Extra diesel required for boring in
rockystrata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and
fro to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0134 Rock Hole Driller day 1.00 645.00 645.00
0114 Beldar day 6.00 645.00 3870.00
0103 Blacksmith 2nd class day 0.75 714.00 535.50
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2010
Code Description Unit Quantity Rate Amount
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 19518.62 W
Add 1 % Water charges on "W" 195.19
TOTAL 19713.81 X
Add GST on "X" (multiplying
factor 0.1405) 2769.79
TOTAL 22483.60 Y
Add 15% CPOH on "Y" 3372.54
TOTAL 25856.14 Z
Add Cess @ 1% on "Z" 258.56
Cost for 16 metre 26114.70
Cost of 1 metre 1632.17
Say 1632.15
23.2.2.3 400 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 14 metre
MACHINERY :
0020 Hydraulic Excavator (3D) with driver
and fuel. day 0.95 7000.00 6650.00
1235 Diesel oil litre 16.00 80.87 1293.92
Extra diesel required for boring in
rockystrata
0005 Hire charges of Diesel Truck - 9 tonne day 0.4286 3940.00 1688.68
Transportation charges for to and fro
to site
(assume 140m of bore for one shifting)
(2 x30)/140
Loading, unloading &Errection charges
of drilling Rig Machine
LABOUR
0114 Beldar day 4.00 645.00 2580.00
0130 Mistry day 1.00 784.00 784.00
7763 Water supply tanker of 5000 litre
capacity each 1.00 1500.00 1500.00
Extra labour to assist M/C operator &
security
0134 Rock Hole Driller day 1.20 645.00 774.00
0114 Beldar day 8.00 645.00 5160.00
0103 Blacksmith 2nd class day 1.00 714.00 714.00
0113 Chowkidar day 1.00 645.00 645.00
TOTAL 21789.60 W
Add 1 % Water charges on "W" 217.90
TOTAL 22007.50 X
Add GST on "X" (multiplying
factor 0.1405) 3092.05
TOTAL 25099.55 Y
Add 15% CPOH on "Y" 3764.93
TOTAL 28864.49 Z
Add Cess @ 1% on "Z" 288.64
Cost for 14 metre 29153.13
Cost of 1 metre 2082.37
Say 2082.35
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2011
23.3 Supplying, assembling, lowering and fixing in vertical position in bore well,
unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:
12818, including required hire and labour charges, fittings & accessories etc. all
complete, for all depths, as per direction of Engineer -in-charge.
23.3.1 100 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7758 uPVC blind pipe 100 mm dia as per
IS: 12818 metre 100.00 405.00 40500.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.50 358.32 179.16
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
9999 Sundries L.S. 10.07 2.12 21.35
TOTAL 41345.51 W
Add 1 % Water charges on "W" 413.46
TOTAL 41758.96 X
Add GST on "X" (multiplying
factor 0.1405) 5867.13
TOTAL 47626.10 Y
Add 15% CPOH on "Y" 7143.91
TOTAL 54770.01 Z
Add Cess @ 1% on "Z" 547.70
Cost of 100 metres 55317.71
Cost of 1 metre 553.18
Say 553.20
23.3.2 150 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7745 uPVC blind pipe 150 mm dia as per
IS: 12818 metre 100.00 490.00 49000.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.50 597.20 298.60
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2012
Code Description Unit Quantity Rate Amount
9999 Sundries (Adhesive etc.) L.S. 10.07 2.12 21.35
TOTAL 49964.95 W
Add 1 % Water charges on "W" 499.65
TOTAL 50464.60 X
Add GST on "X" (multiplying
factor 0.1405) 7090.28
TOTAL 57554.87 Y
Add 15% CPOH on "Y" 8633.23
TOTAL 66188.10 Z
Add Cess @ 1% on "Z" 661.88
Cost of 100 metres 66849.99
Cost of 1 metre 668.50
Say 668.50
23.3.3 200 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7746 uPVC blind pipe 200 mm dia as per
IS: 12818 metre 100.00 700.00 70000.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.50 971.45 485.73
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
9999 Sundries L.S. 10.07 2.12 21.35
TOTAL 71152.07 W
Add 1 % Water charges on "W" 711.52
TOTAL 71863.59 X
Add GST on "X" (multiplying
factor 0.1405) 10096.83
TOTAL 81960.43 Y
Add 15% CPOH on "Y" 12294.06
TOTAL 94254.49 Z
Add Cess @ 1% on "Z" 942.54
Cost of 100 metres 95197.04
Cost of 1 metre 951.97
Say 951.95
23.4 Supplying, assembling, lowering and fixing in vertical position in bore well
unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS:
12818, including hire & labour charges, fittings & accessories etc. all complete, for
all depths, as per direction of Engineer-in-charge.
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2013
23.4.1 100 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7759 uPVC slotted pipe 100 mm dia as per
IS: 12818 metre 100.00 425.00 42500.00
2319 Carriage of Spun iron S & S pipes
100 mm dia 100 metre 0.50 358.32 179.16
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
9999 Sundries (Adhesive etc.) L.S. 10.07 2.12 21.35
TOTAL 43345.51 W
Add 1 % Water charges on "W" 433.46
TOTAL 43778.96 X
Add GST on "X" (multiplying
factor 0.1405) 6150.94
TOTAL 49929.91 Y
Add 15% CPOH on "Y" 7489.49
TOTAL 57419.39 Z
Add Cess @ 1% on "Z" 574.19
Cost of 100 metres 57993.59
Cost of 1 metre 579.94
Say 579.95
23.4.2 150 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7751 uPVC slotted pipe 150 mm dia as per
IS: 12818 metre 100.00 500.00 50000.00
2321 Carriage of Spun iron S & S pipes
150 mm dia 100 metre 0.50 597.20 298.60
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
9999 Sundries (Adhesive etc.) L.S. 10.07 2.12 21.35
TOTAL 50964.95 W
Add 1 % Water charges on "W" 509.65
TOTAL 51474.60 X
Add GST on "X" (multiplying
factor 0.1405) 7232.18
TOTAL 58706.78 Y
Add 15% CPOH on "Y" 8806.02
TOTAL 67512.80 Z
Add Cess @ 1% on "Z" 675.13
Cost of 100 metres 68187.92
Cost of 1 metre 681.88
Say 681.90
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2014
23.4.3 200 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 100 metres
MATERIAL
7752 uPVC slotted pipe 200 mm dia as
per IS: 12818 metre 100.00 810.00 81000.00
2322 Carriage of Spun iron S & S pipes
200 mm dia 100 metre 0.50 971.45 485.73
Qty = 50 to consider 50% of carriage
as per 2321
LABOUR
for lowering
0114 Beldar day 0.50 645.00 322.50
0115 Coolie day 0.50 645.00 322.50
9999 Sundries (Adhesive etc.) L.S. 13.42 2.12 28.45
TOTAL 82159.18 W
Add 1 % Water charges on "W" 821.59
TOTAL 82980.77 X
Add GST on "X" (multiplying
factor 0.1405) 11658.80
TOTAL 94639.56 Y
Add 15% CPOH on "Y" 14195.93
TOTAL 108835.50 Z
Add Cess @ 1% on "Z" 1088.35
Cost of 100 metres 109923.85
Cost of 1 metre 1099.24
Say 1099.25
23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm,
in recharge pit, in the required thickness, for all leads & lifts, all complete as per
direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
7753 Boulder 50 mm to 200 mm cum 1.00 810.00 810.00
including carriage
LABOUR
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 973.37 W
Add 1 % Water charges on "W" 9.73
TOTAL 983.10 X
Add GST on "X" (multiplying
factor 0.1405) 138.13
TOTAL 1121.23 Y
Add 15% CPOH on "Y" 168.18
TOTAL 1289.41 Z
Add Cess @ 1% on "Z" 12.89
Cost of 1 Cum. 1302.31
Say 1302.30
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2015
23.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the
recharge pit, over the existing layer of boulders, in required thickness, for all leads
& lifts, all complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
7754 Gravel 5 mm to 10 mm cum 1.00 815.00 815.00
including carriage
LABOUR
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 978.37 W
Add 1 % Water charges on "W" 9.78
TOTAL 988.15 X
Add GST on "X" (multiplying
factor 0.1405) 138.84
TOTAL 1126.99 Y
Add 15% CPOH on "Y" 169.05
TOTAL 1296.04 Z
Add Cess @ 1% on "Z" 12.96
Cost of 1 Cum. 1309.00
Say 1309.00
23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm
in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete
as per direction of Engineer -in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
7755 Gravel 1.5 mm to 2 mm cum 1.00 815.00 815.00
including carriage
LABOUR
0114 Beldar day 0.25 645.00 161.25
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 978.37 W
Add 1 % Water charges on "W" 9.78
TOTAL 988.15 X
Add GST on "X" (multiplying
factor 0.1405) 138.84
TOTAL 1126.99 Y
Add 15% CPOH on "Y" 169.05
TOTAL 1296.04 Z
Add Cess @ 1% on "Z" 12.96
Cost of 1 Cum. 1309.00
Say 1309.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2016
23.8 Gravel packing in tubewell construction in accordance with IS: 4097, including
providing gravel fine/ medium/ coarse, in required grading & sizes as per actual
requirement, all complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum.
MATERIAL
7772 Pea Gravel cum 1.00 910.00 910.00
including carriage
LABOUR
0114 Beldar day 0.30 645.00 193.50
9999 Sundries L.S. 1.00 2.12 2.12
TOTAL 1105.62 W
Add 1 % Water charges on "W" 11.06
TOTAL 1116.68 X
Add GST on "X" (multiplying
factor 0.1405) 156.89
TOTAL 1273.57 Y
Add 15% CPOH on "Y" 191.04
TOTAL 1464.60 Z
Add Cess @ 1% on "Z" 14.65
Cost of 1 Cum. 1479.25
Say 1479.25
23.9 Providing and fixing factory made precast RCC perforated drain covers, having
concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with
8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including
providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge
binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1 No. RCC drain cover
MATERIAL
7762 Precast R.C.C. perforated slab each 1.00 875.00 875.00
LABOUR
9988 Carriage and fixing charges L.S. 15.00 2.12 31.80
TOTAL 906.80 W
Add 1 % Water charges on "W" 9.07
TOTAL 915.87 X
Add GST on "X" (multiplying
factor 0.1405) 128.68
TOTAL 1044.55 Y
Add 15% CPOH on "Y" 156.68
TOTAL 1201.23 Z
Add Cess @ 1% on "Z" 12.01
Cost of 1 No. 1213.24
Say 1213.25
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2017
23.10 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW
(Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended
casing pipes of required dia, conforming to IS: 4270, of reputed & approved make,
including painted with outside surface with two coats of anticorrosive paint of
approved brand and manufacture, including required hire & labour charges, fittings
& accessories, all complete, for all depths, as per direction of Engineer-in-charge.
23.10.1 100 mm nominal size dia having minimum wall thickness 5.00 mm
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7757 M.S. pipe 100 mm dia casing pipe metre 30.00 780.00 23400.00
7764 M.S. socket 100 mm dia each 5.00 125.00 625.00
2343 Carriage of ductile iron pipes (k7)
100 mm dia 100 metre 0.30 358.32 107.50
including loading and unloading
Painting with anticorrosive Paint 3.14
x.0110x30.00=10.36 sqm.
13.65.1 Rate as per Item No.13.65.1 of
SH: Finishing sqm 10.36 115.10 1192.44 A
LABOUR
0114 Beldar day 1.35 645.00 870.75
0130 Mistry day 0.50 784.00 392.00
TOTAL 26587.68 W
Add 1 % Water charges on "W-A" 253.95
TOTAL 26841.63 X
Add GST on "X-A" (multiplying
factor 0.1405) 3603.71
TOTAL 30445.35 Y
Add 15% CPOH on "Y-A" 4387.94
TOTAL 34833.28 Z
Add Cess @ 1% on "Z-A" 336.41
Cost for 30 metre 35169.69
Cost of 1 metre 1172.32
Say 1172.30
23.10.2 150 mm nominal size dia having minimum wall thickness 5.00 mm
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7743 M.S. pipe 150 mm dia casing pipe metre 30.00 1126.00 33780.00
7765 M.S. socket 150 mm dia each 5.00 205.00 1025.00
2344 Carriage of cast iron pipes 150 mm dia 100 metre 0.30 597.20 179.16
including loading and unloading
Painting with Anticorrosive Paint 3.14
x0.160x30.00=15.07 sqm.
13.65.1 Rate as per Item No.13.65.1 of
SH:Finishing sqm 15.07 115.10 1734.56 A
LABOUR
0114 Beldar day 1.40 645.00 903.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2018
Code Description Unit Quantity Rate Amount
0130 Mistry day 0.50 784.00 392.00
TOTAL 38013.72 W
Add 1 % Water charges on "W-A" 362.79
TOTAL 38376.51 X
Add GST on "X-A" (multiplying
factor 0.1405) 5148.19
TOTAL 43524.70 Y
Add 15% CPOH on "Y-A" 6268.52
TOTAL 49793.22 Z
Add Cess @ 1% on "Z-A" 480.59
Cost for 30 metre 50273.81
Cost of 1 metre 1675.79
Say 1675.80
23.10.3 200 mm nominal size dia having minimum wall thickness 5.40 mm
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7744 M.S. pipe 200 mm dia casing pipe metre 30.00 1400.00 42000.00
7766 M.S. socket 200 mm dia each 5.00 265.00 1325.00
2345 Carriage of cast iron pipes 200 mm dia 100 metre 0.30 971.45 291.44
including loading and unloading
Painting with anticorrosive Paint
3.14 x0.210x30.00=20.25 sqm.
13.65.1 Rate as per Item No.13.65.1 of
SH:Finishing sqm 20.25 115.10 2330.78 A
LABOUR
0114 Beldar day 1.45 645.00 935.25
0130 Mistry day 0.50 784.00 392.00
TOTAL 47274.46 W
Add 1 % Water charges on "W-A" 449.44
TOTAL 47723.90 X
Add GST on "X-A" (multiplying
factor 0.1405) 6377.73
TOTAL 54101.63 Y
Add 15% CPOH on "Y-A" 7765.63
TOTAL 61867.26 Z
Add Cess @ 1% on "Z-A" 595.36
Cost for 30 metre 62462.62
Cost of 1 metre 2082.09
Say 2082.10
23.11 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW
(Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm)
mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia,
conforming to IS: 8110, of reputed and approved make, having wall thickness not
less than 5.40 mm, including painted with outside surface with two coats of
anticorrosive bitumestic paint of approved brand and manufacture, including hire
& labour charges, fittings & accessories, all complete, for all depths, as per direction
of Engineer -in-charge.
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2019
23.11.1 100 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7757 M.S. pipe 100 mm dia casing pipe metre 30.00 780.00 23400.00
7764 M.S. socket 100 mm dia each 5.00 125.00 625.00
9999 Sundries L.S. 906.04 2.12 1920.80
2343 Carriage of ductile iron pipes (k7)
100 mm dia 100 metre 0.30 358.32 107.50
including loading and unloading
Painting with anticorrosive Paint
3.14 x.11x30.00=10.36 sqm
13.65.1 Rate as per Item No.13.65.1 of
SH:Finishing sqm 10.36 115.10 1192.44 A
LABOUR
0114 Beldar day 1.35 645.00 870.75
0130 Mistry day 0.50 784.00 392.00
TOTAL 28508.49 W
Add 1 % Water charges on "W-A" 273.16
TOTAL 28781.65 X
Add GST on "X-A" (multiplying
factor 0.1405) 3876.28
TOTAL 32657.93 Y
Add 15% CPOH on "Y-A" 4719.82
TOTAL 37377.76 Z
Add Cess @ 1% on "Z-A" 361.85
Cost for 30 metre 37739.61
Cost of 1 metre 1257.99
Say 1258.00
23.11.2 150 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7743 M.S. pipe 150 mm dia casing pipe metre 30.00 1126.00 33780.00
7765 M.S. socket 150 mm dia each 5.00 205.00 1025.00
9999 Extra for making slots L.S. 1208.05 2.12 2561.07
2344 Carriage of cast iron pipes 150 mm dia 100 metre 0.30 597.20 179.16
including loading and unloading
Painting with anticorrosive Paint
3.14 x.160x30.00=15.07 sqm.
13.65.1 Rate as per Item No.13.65.1 of
SH:Finishing sqm 15.07 115.10 1734.56 A
LABOUR
0114 Beldar day 1.40 645.00 903.00
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2020
Code Description Unit Quantity Rate Amount
0130 Mistry day 0.50 784.00 392.00
TOTAL 40574.78 W
Add 1 % Water charges on "W-A" 388.40
TOTAL 40963.19 X
Add GST on "X-A" (multiplying
factor 0.1405) 5511.62
TOTAL 46474.81 Y
Add 15% CPOH on "Y-A" 6711.04
TOTAL 53185.85 Z
Add Cess @ 1% on "Z-A" 514.51
Cost for 30 metre 53700.36
Cost of 1 metre 1790.01
Say 1790.00
23.11.3 200 mm nominal size dia
Code Description Unit Quantity Rate Amount
Details of cost for 30 metre
MATERIAL
7744 M.S. pipe 200 mm dia casing pipe metre 30.00 1400.00 42000.00
7766 M.S. socket 200 mm dia each 5.00 265.00 1325.00
9999 Extra for making slots L.S. 1208.05 2.12 2561.07
2345 Carriage of cast iron pipes 200 mm dia 100 metre 0.30 971.45 291.44
including loading and unloading
Painting with anticorrosive Paint
3.14 x 0.210x30.00=20.25 sqm.
13.65.1 Rate as per Item No.13.65.1 of
SH:Finishing sqm 20.25 115.10 2330.78 A
LABOUR
0114 Beldar day 1.40 645.00 903.00
0130 Mistry day 0.50 784.00 392.00
TOTAL 49803.28 W
Add 1 % Water charges on "W-A" 474.73
TOTAL 50278.00 X
Add GST on "X-A" (multiplying
factor 0.1405) 6736.59
TOTAL 57014.59 Y
Add 15% CPOH on "Y-A" 8202.57
TOTAL 65217.16 Z
Add Cess @ 1% on "Z-A" 628.86
Cost for 30 metre 65846.02
Cost of 1 metre 2194.87
Say 2194.85
23.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to
establish maximum rate of usable water yield without sand content (beyond
permissible limit), with required capacity air compressor, running the compressor
for required time till well is fully developed, measuring yield of well by "V" notch
method or any other approved method, measuring static level & draw down etc. by
step draw down method, collecting water samples & getting tested in approved
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2021
laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges
of air compressor, tools & accessories etc., all as per requirement and direction of
Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 8 Hours
MACHINERY :
0040 Air compressor 250 cfm with two leads
for pneumatic cutters/ hammers. day 1.00 1600.00 1600.00
MATERIAL
1235 Diesel oil litre 48.00 80.87 3881.76
TOTAL 5481.76 W
Add 1 % Water charges on "W" 54.82
TOTAL 5536.58 X
Add GST on "X" (multiplying
factor 0.1405) 777.89
TOTAL 6314.47 Y
Add 15% CPOH on "Y" 947.17
TOTAL 7261.64 Z
Add Cess @ 1% on "Z" 72.62
Cost of 8 Hours 7334.25
Cost of 1 Hour 916.78
Say 916.80
23.13 Providing and fixing suitable size threaded mild steel cap or spot welded plate to
the top of bore well housing/ casing pipe, removable as per requirement, all complete
for borewell of:
23.13.1 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
100mm dia MS screwed cap with
locking arrangement
7760 M.S. cap 100 mm dia each 1.00 135.00 135.00 P
Add 5% labour factor on P 6.75
TOTAL 141.75 W
Add 1 % Water charges on "W" 1.42
TOTAL 143.17 X
Add GST on "X" (multiplying
factor 0.1405) 20.12
TOTAL 163.28 Y
Add 15% CPOH on "Y" 24.49
TOTAL 187.77 Z
Add Cess @ 1% on "Z" 1.88
Cost of 1 No 189.65
Say 189.65
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2022
23.13.2 150 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
150 mm dia MS screwed cap with
locking arrangement
7747 M.S. cap 150 mm dia each 1.00 150.00 150.00
Add 5% labour facor on X 7.50
TOTAL 157.50 W
Add 1 % Water charges on "W" 1.58
TOTAL 159.08 X
Add GST on "X" (multiplying
factor 0.1405) 22.35
TOTAL 181.43 Y
Add 15% CPOH on "Y" 27.21
TOTAL 208.64 Z
Add Cess @ 1% on "Z" 2.09
Cost of 1 No 210.73
Say 210.75
23.13.3 200 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
200 mm dia MS screwed cap with
locking arrangement
7748 M.S. cap 200 mm dia each 1.00 200.00 200.00
Add 5% labour facor on X 10.00
TOTAL 210.00 W
Add 1 % Water charges on "W" 2.10
TOTAL 212.10 X
Add GST on "X" (multiplying
factor 0.1405) 29.80
TOTAL 241.90 Y
Add 15% CPOH on "Y" 36.29
TOTAL 278.19 Z
Add Cess @ 1% on "Z" 2.78
Cost of 1 No 280.97
Say 280.95
23.14 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe
of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required
size complete.
23.14.1 100 mm clamp
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
Clamps made of MS flat of size
100x10mm thick1x2mt.x7.80 kg per
mt.=15.60 kg.
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2023
Code Description Unit Quantity Rate Amount
10.1 Rate as per Item No.10.1 of
SH: Steel Work kg 15.60 93.05 1451.58 A
9999 Sundries, nuts and bolts etc. L.S. 25.00 2.12 53.00
TOTAL 1504.58 W
Add 1 % Water charges on "W-A" 0.53
TOTAL 1505.11 X
Add GST on "X-A" (multiplying
factor 0.1405) 7.52
TOTAL 1512.63 Y
Add 15% CPOH on "Y-A" 9.16
TOTAL 1521.79 Z
Add Cess @ 1% on "Z-A" 0.70
Cost of 1 No 1522.49
Say 1522.50
23.14.2 150 mm clamp
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
Clamps made of MS flat of size
100x10mm thick1x2.10 mt.x7.80 kg
per mt.=16.38 kg.
10.1 Rate as per Item No.10.1 of
SH: Steel Work kg 16.38 93.05 1524.16 A
9999 Sundries, nuts and bolts etc. L.S. 30.00 2.12 63.60
TOTAL 1587.76 W
Add 1 % Water charges on "W-A" 0.64
TOTAL 1588.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 9.03
TOTAL 1597.42 Y
Add 15% CPOH on "Y-A" 10.99
TOTAL 1608.41 Z
Add Cess @ 1% on "Z-A" 0.84
Cost of 1 No 1609.25
Say 1609.25
23.14.3 200 mm clamp
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
Clamps made of MS flat of size
100x10mm thick1x2.40 mt.x7.80 kg
per mt.=18.72 kg.
10.1 Rate as per Item No.10.1 of
SH: Steel Work kg 18.72 93.05 1741.90 A
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2024
Code Description Unit Quantity Rate Amount
9999 Sundries, nuts and bolts etc. L.S. 30.00 2.12 63.60
TOTAL 1805.50 W
Add 1 % Water charges on "W-A" 0.64
TOTAL 1806.13 X
Add GST on "X-A" (multiplying
factor 0.1405) 9.03
TOTAL 1815.16 Y
Add 15% CPOH on "Y-A" 10.99
TOTAL 1826.15 Z
Add Cess @ 1% on "Z-A" 0.84
Cost of 1 No 1826.99
Say 1827.00
23.15 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe
assembly of tubewell as per IS:2800 (part I).
23.15.1 100 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
7761 M.S. bail plug 100 mm dia each 1.00 160.00 160.00
9999 Sundries L.S. 5.00 2.12 10.60
TOTAL 170.60 W
Add 1 % Water charges on "W" 1.71
TOTAL 172.31 X
Add GST on "X" (multiplying
factor 0.1405) 24.21
TOTAL 196.51 Y
Add 15% CPOH on "Y" 29.48
TOTAL 225.99 Z
Add Cess @ 1% on "Z" 2.26
Cost of 1 No 228.25
Say 228.25
23.15.2 150 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
7749 M.S bail plug 150 mm dia each 1.00 200.00 200.00
9999 Sundries L.S. 5.00 2.12 10.60
TOTAL 210.60 W
Add 1 % Water charges on “W” 2.11
TOTAL 212.71 X
Add GST on “X” (multiplying
factor 0.1405) 29.89
TOTAL 242.59 Y
Add 15% CPOH on “Y” 36.39
TOTAL 278.98 Z
Add Cess @ 1% on “Z” 2.79
Cost of 1 No 281.77
Say 281.75
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2025
23.15.3 200 mm dia
Code Description Unit Quantity Rate Amount
Details of cost for 1 No
MATERIAL
7750 M.S bail plug 200 mm dia each 1.00 220.00 220.00
9999 Sundries L.S. 5.00 2.12 10.60
TOTAL 230.60 W
Add 1 % Water charges on “W” 2.31
TOTAL 232.91 X
Add GST on “X” (multiplying
factor 0.1405) 32.72
TOTAL 265.63 Y
Add 15% CPOH on “Y” 39.84
TOTAL 305.47 Z
Add Cess @ 1% on “Z” 3.05
Cost of 1 No 308.53
Say 308.55
SUB HEAD : 23- RAIN WATER HARVESTING & TUBEWELLS 2026
SUB HEAD : 24.0
CONSERVATION
OF
HERITAGE BUILDINGS
2027
24.1 Raking out joints of stone masonry surface to the required width and depth,
with due care and precaution, by mechanical / manual means, including
preparing and cleaning the surface for re-pointing/ refilling of joints, including
disposal of rubbish to the dumping ground within 50 metre lead.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
LABOUR
0114 Beldar day 0.53 645.00 341.85
0115 Coolie day 0.08 645.00 51.60
0101 Bhisti day 0.07 714.00 49.98
9999 Sundries L.S. 1.43 2.12 3.03
TOTAL 446.46 W
Add 1 % Water charges on "W" 4.46
TOTAL 450.93 X
Add GST on "X" (multiplying
factor 0.1405) 63.36
TOTAL 514.28 Y
Add 15% CPOH on "Y" 77.14
TOTAL 591.42 Z
Add Cess @ 1% on "Z" 5.91
Cost of 10.00 sqm 597.34
Cost of 1.00 sqm 59.73
Say 59.75
24.2 Providing and fixing double scaffolding system (cup lock type) on the exterior
side of building/structure, upto 25 metre height, above ground level, including
additional rows of scaffolding in stepped manner as per requirement of site,
made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal &
vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis,
M.S. clamps and staircase system in the scaffolding for working platform etc.
and maintaining it in a serviceable condition for execution of work of cleaning
and/ or pointing and/ or applying chemical and removing it thereafter. The
scaffolding system shall be stiffened with bracings, runners, connecting with
the building etc, wherever required, if feasible, for inspection of work at
required locations with essential safety features for the workmen etc., complete
as per directions and approval of Engineer-in-charge.
Note:- (1) The elevational area of the scaffolding shall be measured for payment
purpose. (2) The payment will be made once only for execution of all items for
such works.
Code Description Unit Quantity Rate Amount
Details of cost for area 22.5x9.0
=202.50 sqm
MATERIAL
Assuming shuttering material will
become unserviceable after use of 40
times Adding for maintenance @ 10%
of cost
Taking slvage value after full use of
material @ 25% of cost
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2029
Code Description Unit Quantity Rate Amount
7397 Base jack each 0.30 145.00 43.50
Qty taken for cost of using once
=14x0.85/40=0.2975
4009 Mild steel tubes hot finished welded type kilogram 80.02 60.00 4801.20
Vertical standard 2.5m length
=7x2x9x2.5=315.00 m
Side support 6.00m length
=3x2x6.00=36.00m
Horizonatal support 3.00mlength
=18x3x3.00=162.00m
Total=1026.00m
@ 3.67 kg/m =3765.42 kgQty taken for
cost of using once= 3765.42x0.85/40
=80.02kg
7387 Spigot for standard jointing kg 2.63 40.00 105.20
7x2x9=126 nos x 0.40m length =
50.40m @2.46kg /m=123.98kgQty
taken for cost of using once=
123.98x0.85/40=2.63kg
1034 Bolts and nuts upto 300 mm in length quintal 0.008 5200.00 41.60
2x7x2x9=252 nos @ 0.15 kg
each=37.80 kg =0.378qQty taken for
cost of using once= 0.378x0.85/
40=0.008q
7346 Double coupler each 2.55 46.00 117.30
Clamp coupler for fixing MS tube with
scafolding 2x3x2+2x18x3=120 nosQty
taken for cost of using once=
120x0.85/40=2.55 nos
7398 Challies each 1.91 765.00 1461.15
3 nos x 18 lines=54 nosTwo level plate
challies=2x18 lines=36nosTotal
= 90 nos
Qty taken for cost of using once
=90x0.85/40=1.9125 nos
7399 Cup lock each 27.92 48.00 1340.16
For Vertical standards=(5x7x2x9=
630 nos) +(2x18x19=694 nos)
Total=1314 nos
Qty taken for cost of using once
= 1314x0.85/40=27.92
2205 Carriage of Steel tonne 6.054 145.72 882.19
40mm dia MS pipe=3765.42kg
25mm spigot=123.98kgNuts &
bolts=37.80kgclamp=120 [email protected]
each=120.00kgChallies=90 nos @
15.00kg
each=1350.00kgCup locks=1314 nos @
0.50kg each=
657.00kgTotal=6054.20kg=6.054 tonne
LABOUR
0116 Fitter (grade 1) day 15.50 784.00 12152.00
0114 Beldar day 31.00 645.00 19995.00
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2030
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 1035.00 2.12 2194.20
TOTAL 43133.50 W
Add 1 % Water charges on "W" 431.33
TOTAL 43564.83 X
Add GST on "X" (multiplying
factor 0.1405) 6120.86
TOTAL 49685.69 Y
Add 15% CPOH on "Y" 7452.85
TOTAL 57138.55 Z
Add Cess @ 1% on "Z" 571.39
Cost of 202.50 sqm 57709.93
Cost of 1.00 sqm 284.99
Say 285.00
24.3 Cleaning the sand stone surface and removing dirt, dust, bird dropping, grease,
oil, algae, fungus, monkey beats, vegetable growth etc., including providing,
applying and washing the surface with liquid Ammonia Chemical of 5%
solution and other chemical cleaning agent as approved by Archaeological
Survey of India/ Engineer-in-charge, of approved brand and manufacturer,
with the help of required scrubbers and also cleaning with machine operated
water jet mixed with desired quantity of fine silica where ever required, without
causing any scratching/ damage to the stone surface and finally washing the
surface with clean water with the help of pressure jet machine, complete in all
respect, including taking all precautions to safeguard ventilators, windows,
doors etc. by suitable covering so as to avoid any damage to the building/
structure, all as per direction of Engineer-in-charge (The rate is inclusive of
all materials & labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
7767 Stone cleaning chemical approved by ASI litre 0.10 270.00 27.00
1 kg teepal of 3% solution for 10 sqm
area for 10sqm = 0.10 liter
7771 Liquid Amonia 5% litre 0.17 145.00 24.65
LABOUR (for applying the camical
Salution)
0131 Painter day 0.20 714.00 142.80
0114 Beldar day 0.20 645.00 129.00
0128 Mate day 0.10 714.00 71.40
9999 Cleaning T & P & its manitinance cost
(Jet Pump, electrice cable, horse pipe,
waler pipe, Nozel safety belt Rope &
mantance cost and safety machine for
window etc.) L.S. 1.00 2.12 2.12
6501 Sand zone V (Jamuna) cum 0.0283 1300.00 36.79
LABOUR (for pressure cleaning)
0103 Blacksmith 2nd class day 0.40 714.00 285.60
0114 Beldar day 0.80 645.00 516.00
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2031
Code Description Unit Quantity Rate Amount
0128 Mate day 0.10 714.00 71.40
TOTAL 1306.76 W
Add 1 % Water charges on "W" 13.07
TOTAL 1319.83 X
Add GST on "X" (multiplying
factor 0.1405) 185.44
TOTAL 1505.26 Y
Add 15% CPOH on "Y" 225.79
TOTAL 1731.05 Z
Add Cess @ 1% on "Z" 17.31
Cost of 10.00 sqm 1748.36
Cost of 1.00 sqm 174.84
Say 174.85
24.4 Providing and applying antifungal wash treatment using 3% solution of sodium
pentachlorophenate, of reputed brand and manufacturer, on cleaned sand
stone surface at desired locations as per direction of Engineer-in-charge (The
rate is inclusive of all materials & labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
7775 Sodium pentachlorophenate Kg 0.10 500.00 50.00
LABOUR
0131 Painter day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
0128 Mate day 0.125 714.00 89.25
TOTAL 479.00 W
Add 1 % Water charges on “W” 4.79
TOTAL 483.79 X
Add GST on “X” (multiplying
factor 0.1405) 67.97
TOTAL 551.76 Y
Add 15% CPOH on “Y” 82.76
TOTAL 634.53 Z
Add Cess @ 1% on “Z” 6.35
Cost of 10.00 sqm 640.87
Cost of 1.00 sqm 64.09
Say 64.10
24.5 Ruled / Flush pointing on Red sand stone masonry surface with lime, surkhi
and marble dust mortar in the ratio of 1:1.5:1/2 {One lime: 1.5 surkhi (50% red
and 50% light yellow surkhi ) : 1/2 marble dust}. (The rate is inclusive of all
materials & labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
3.19 Rate as per Item No.3.19 of SH:Mortars cum 0.023 3140.50 72.23
LABOUR
0155 Mason (average) day 0.92 749.00 689.08
0115 Coolie day 1.37 645.00 883.65
0101 Bhisti day 0.93 714.00 664.02
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2032
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 4.03 2.12 8.54
TOTAL 2317.53 W
Add 1 % Water charges on "W" 23.18
TOTAL 2340.70 X
Add GST on "X" (multiplying
factor 0.1405) 328.87
TOTAL 2669.57 Y
Add 15% CPOH on "Y" 400.44
TOTAL 3070.00 Z
Add Cess @ 1% on "Z" 30.70
Cost of 10.00 sqm 3100.70
Cost of 1.00 sqm 310.07
Say 310.05
24.6 Ruled/ Flush pointing on White sand stone masonry surface with lime, surkhi
and marble dust mortar in the ratio of 1:1.5:1/2 {One lime : 1.5 surkhi (15%
dark red and 85% light yellow surkhi) : 1/2 marble dust}. (The rate is inclusive
of all materials & labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
3.19 Rate as per Item No.3.19 of SH:Mortars cum 0.023 3140.50 72.23
LABOUR
0155 Mason (average) day 0.92 749.00 689.08
0115 Coolie day 1.37 645.00 883.65
0101 Bhisti day 0.93 714.00 664.02
9999 Sundries L.S. 4.03 2.12 8.54
TOTAL 2317.53 W
Add 1 % Water charges on "W" 23.18
TOTAL 2340.70 X
Add GST on "X" (multiplying
factor 0.1405) 328.87
TOTAL 2669.57 Y
Add 15% CPOH on "Y" 400.44
TOTAL 3070.00 Z
Add Cess @ 1% on "Z" 30.70
Cost of 10.00 sqm 3100.70
Cost of 1.00 sqm 310.07
Say 310.05
24.7 Applying two or more coat of Ethyl Silicate chemical as approved by
Archaeological Survey of India/ Engineer-in-charge, of approved brand and
manufacturer, with brush or spray on the existing stone masonry surface till
there is no further absorption of chemical by stone surface, including
protecting the applied surface from direct sunlight by suitable means during
application, all complete as per direction of the Engineer-in-Charge (The rate
is inclusive of all materials & labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 5 sqm
MATERIAL
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2033
Code Description Unit Quantity Rate Amount
7769 Stone surface strengthening chemical
approved by ASI litre 1.00 835.00 835.00
LABOUR
0131 Painter day 0.15 714.00 107.10
0114 Beldar day 0.15 645.00 96.75
9999 Sundries L.S. 6.00 2.12 12.72
TOTAL 1051.57 W
Add 1 % Water charges on "W" 10.52
TOTAL 1062.09 X
Add GST on "X" (multiplying
factor 0.1405) 149.22
TOTAL 1211.31 Y
Add 15% CPOH on "Y" 181.70
TOTAL 1393.01 Z
Add Cess @ 1% on "Z" 13.93
Cost of 5.00 sqm 1406.94
Cost of 1.00 sqm 281.39
Say 281.40
24.8 Applying breathable, non-reactive, antifungal, and water repellant Silane/
Siloxane chemical as approved by Archaeological Survey of India/ Engineer-
in-charge, of approved brand and manufacture, diluted with solvent mineral
Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of
Turpentine oil), on the existing sand stone masonry surface with two or more
coats to give uniform application of chemical on the surface, all complete as
per direction of Engineer-In-charge (The rate is inclusive of all materials &
labours involved except scaffolding).
Code Description Unit Quantity Rate Amount
Detail of cost for 45 sqm
MATERIAL
7768 Water repallent chemical approved by ASI litre 1.00 1100.00 1100.00
7770 Turpentine oil litre 12.00 50.00 600.00
LABOUR
0131 Painter day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
9999 Handling / Transportation charges L.S. 6.00 2.12 12.72
TOTAL 3071.72 W
Add 1 % Water charges on "W" 30.72
TOTAL 3102.44 X
Add GST on "X" (multiplying
factor 0.1405) 435.89
TOTAL 3538.33 Y
Add 15% CPOH on "Y" 530.75
TOTAL 4069.08 Z
Add Cess @ 1% on "Z" 40.69
Cost of 45.00 sqm 4109.77
Cost of 1.00 sqm 91.33
Say 91.35
SUB HEAD : 24- CONSERVATION OF HERITAGE BUILDINGS 2034
SUB HEAD : 25.0
STRUCTURAL GLAZING
ALUMINIUM COMPOSITE PANEL
2035
25.1 Providing and supplying aluminium extruded tubular and other aluminium
sections as per the architectural drawings and approved shop drawings , the
aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super
durable powder coating of 60-80 microns conforming to AAMA 2604 of required
colour and shade as approved by the Engineer-in-Charge. ( The item includes
cost of material such as cleats, sleeves, screws etc. necessary for fabrication
of extruded aluminium frame work. Nothing extra shall be paid on this account).
The weight of aluminium extruded section shall be taken for purpose of
payment.
Code Description Unit Quantity Rate Amount
Details of cost for 6.50 kg
Width of the unit 1.6 m
Height of the unit 4.2 m
Area of Single Unit 6.72 sqm
Total Area 6.72 sqm, No of Panels 1 no
Aluminium Weight per sqm = 6.50 Kg/m2
Vision Height 2.2 m
Add for cleats, sleeves, screws etc.
@5% = 0.33 kg
Add wastage @ 5% = 0.34 kg
Total = 7.17 kg
Details of cost for 6.50 kg
MATERIALS
7306 Aluminium T or L sections kilogram 7.17 190.00 1362.30
7392 Powder coating 50 microns on
aluminium sections kilogram 7.17 61.00 437.37
TOTAL 1799.67 W
Add 1 % Water charges on "W" 18.00
TOTAL 1817.67 X
Add GST on "X" (multiplying
factor 0.1405) 255.38
TOTAL 2073.05 Y
Add 15% CPOH on "Y" 310.96
TOTAL 2384.01 Z
Add Cess @ 1% on "Z" 23.84
Cost for 6.5 kg 2407.85
Cost for 1 kg 370.44
Say 370.45
25.2 Designing, fabricating, testing, protection, installing and fixing in position semi
(grid) unitized system of structural glazing (with open joints) for linear as well as
curvilinear portions of the building for all heights and all levels, including:
(a) Structural analysis & design and preparation of shop drawings for the
specified design loads conforming to IS 875 part III (the system must passed
the proof test at 1.5 times design wind pressure without any failure), including
functional design of the aluminum sections for fixing glazing panels of various
thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws,
toggles, nuts, bolts, clamps etc., structural and weather silicone sealants,
flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets
for water tightness, pressure equalisation & drainage and protection against
fire hazard including:
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2037
(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium
alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to
accommodate 3 Dimentional movement for achieving perfect verticality and
fixing structural glazing system rigidly to the RCC/ masonry/structural steel
framework of building structure using stainless steel anchor fasteners/ bolts,
nylon seperator to prevent bimetallic contacts with nuts and washers etc. of
stainless steel grade 316, of the required capacity and in required numbers.
(c) Providing and filling, two part pump filled, structural silicone sealant and
one part weather silicone sealant compatible with the structural silicone sealant
of required bite size in a clean and controlled factory / work shop environment,
including double sided spacer tape, setting blocks and backer rod, all of
approved grade, brand and manufacture, as per the approved sealant design,
within and all around the perimeter for holding glass.
(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm
thick and of sizes, shapes and profiles, as required as per the site conditions,
to seal the gap between the building structure and all its interfaces with curtain
glazing to make it watertight.
(e) Making provision for drainage of moisture/ water that enters the curtain
glazing system to make it watertight, by incorporating principles of pressure
equalization, providing suitable gutter profiles at bottom (if required), making
necessary holes of required sizes and of required numbers etc. complete.
This item includes cost of all inputs of designing, labour for fabricating and
installation of aluminium grid, installation of glazed units, T&P, scaffolding
and other incidental charges including wastages etc., enabling temporary
structures and services, cranes or cradles etc. as described above and as
specified. The item includes the cost of getting all the structural and functional
design including shop drawings checked by a structural designer, dully
approved by Engineer-in-charge. The item also includes the cost of all mock
ups at site, cost of all samples of the individual components for testing in an
approved laboratory, field tests on the assembled working structural glazing
as specified, cleaning and protection till the handing over of the building for
occupation. In the end, the Contractor shall provide a water tight structural
glazing having all the performance characteristics etc. all complete as
required, as per the Architectural drawings, as per item description, as
specified, as per the approved shop drawings and as directed by the Engineer-
in-Charge.
Note:- 1. The cost of providing extruded aluminium frames, shadow boxes,
extruded aluminium section capping for fixing in the grooves of the curtain
glazing and vermin proof stainless steel wire mesh shall be paid for separately
under relevant items under this sub- head. However, for the purpose of
payment, only the actual area of structural glazing (including width of grooves)
on the external face shall be measured in sqm. up to two decimal places.
Note:-2. The following performance test are to be conducted on structural
glazing system if area of structural glazing exceeds 2500 Sqm from the
certified laboratories accreditated by NABL(National Accreditation Board for
Testing and Calibration Laboratories), Department of Science & Technologies,
India. Cost of testing is payable separately.
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2038
The NIT approving authority will decide the necessity of testing on the basis
of cost of the work, cost of the test and importance of the work. Performance
Testing of Structural glazing system Tests to be conducted in the NABL
accredited lab or any other accreditation body which operates in accordance
with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025
1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) &
(+50pa to +300pa) as per ASTM E-283-04 testing method for a range of
testing limit 1 to 200 mVhr
2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09
testing method for a range up to 2000 ml.
3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05
testing method for a range upto 2000 ml
4. Structural Performance Deflection and deformation by static air pressure
test (1.5 times design wind pressure without any failure) as per ASTME-
330-10 testing method for a range upto 50 mm
5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing
method for Qualitative test, Tests to be conducted on site.
6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa
(35psi) upto 2000 ml
Code Description Unit Quantity Rate Amount
Details of cost for 6.72 sqm
Width of the unit 1.6 m
Height of the unit 4.2 m
Area of Single Unit 6.72 sqm
Total Area 6.72 sqm, No of Panels 1 no
Aluminium Weight per sqm
= 6.50 Kg/sqm
Vision Height 2.2 m
Sparndrel Height 2.0 m
Details of cost for 6.72 sqm
MATERIALS
2605 Structural sealant - 6 mm x 12 mm metre 17.02 31.00 527.62
2606 Spacer tape 6.4 mm thick x 6 mm wide metre 20.11 21.00 422.31
2607 Weather Sealant - Non Staining (600 ml) each 1.96 332.00 650.72
2608 Weather Sealant - Normal (300 ml) each 2.55 102.00 260.10
2609 MS Brackets/Aluminium Alloy Brackets kg 9.78 104.00 1017.12
2610 Silicon Gasket in Kg (Above 50 g / m) kg 0.78 484.00 377.52
2611 EPDM Gasket in Kg (Above 60 g / m) kg 0.70 156.00 109.20
2612 Anchor Fastner - M10 each 2.00 11.00 22.00
2613 SS Bolt with washer of sizes for
structural glazing / ACP Cladding each 2.00 37.00 74.00
2630 Baker rod metre 5.04 6.00 30.24
2614 SS Screws of sizes for structural
glazing /ACP Cladding each 52.00 4.00 208.00
2632 Fire Stop metre 1.60 480.00 768.00
2615 Protective Tape metre 6.72 22.00 147.84
2616 GI flashing - 1.2 mm Thick kg 3.96 61.00 241.56
8654 Masking tape metre 6.72 2.18 14.65
9999 Sundries L.S. 225.50 2.12 478.06
9999 Sundries (For Fabrication) L.S. 1804.03 2.12 3824.54
9999 Sundries (For Installation) L.S. 1804.03 2.12 3824.54
9999 Sundries (Transporation) L.S. 451.00 2.12 956.12
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2039
Code Description Unit Quantity Rate Amount
9999 Sundries (Scaffolding / Loading /
Unloading) L.S. 573.00 2.12 1214.76
9999 Sundries (Designing charges etc.) L.S. 216.18 2.12 458.30
TOTAL 15627.21 W
Add 1 % Water charges on "W" 156.27
TOTAL 15783.48 X
Add GST on "X" (multiplying
factor 0.1405) 2217.58
TOTAL 18001.06 Y
Add 15% CPOH on "Y" 2700.16
TOTAL 20701.22 Z
Add Cess @ 1% on "Z" 207.01
Cost for 6.72 sqm 20908.23
Cost for 1 sqm 3111.34
Say 3111.35
25.3 Providing, assembling and supplying vision glass panels (IGUs) comprising
of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel
units of size and shape as required and specified, comprising of an outer heat
strengthened float glass 6mm thick, of approved colour and shade with
reflective soft coating on surface # 2 of approved colour and shade, an inner
Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide,
dessicants, including primary seal and secondary seal (structural silicone
sealant) etc. all complete for the required performances, as per the Architectural
drawings, as per the approved shop drawings, as specified and as directed
by the Engineer-in-Charge. The IGUs shall be assembled in the factory/
workshop of the glass processor.
(Payment for fixing of IGU Panels in the curtain glazing is included in cost of
item No.25.2)
For payment, only the actual area of glass on face # 1 of the glass panels
(excluding the areas of the grooves and weather silicone sealant) provided
and fixed in position, shall be measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating
on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved
make having properties as visible Light transmittance (VLT) of 25 to 35 %,
Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The
properties of performance glass shall be decided by technical sanctioning
authority as per the site requirement.
Code Description Unit Quantity Rate Amount
Details of cost for 6.72 sqm
Width of the unit 1.6 m
Height of the unit 4.2 m
Area of Single Unit 6.72 sqm
Total Area 6.72 sqm, No of Panels 1 no
Area of Glass deducting area of gap/
grove 5% = 6.38 sqm
Vision Height 2.2 m
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2040
Code Description Unit Quantity Rate Amount
Wastage 10% = 0.638 sqm say 0.7 sqm
Net = 7.02 sqm
Details of cost for 6.72 sqm
MATERIALS
2617 6 mm thick High performance glass sqm 7.02 1030.00 7230.60
2618 6 mm thick clear heat strengthened glass sqm 7.02 670.00 4703.40
9999 Sundries (for insurance Charges) L.S. 126.27 2.12 267.69
9999 Sundries ( Fabrication charges
including silicon sealant, baker rod,
desecant etc. L.S. 2120.13 2.12 4494.68
9999 Transporation including loading and
unloading L.S. 126.27 2.12 267.69
TOTAL 16964.06 W
Add 1 % Water charges on "W" 169.64
TOTAL 17133.70 X
Add GST on "X" (multiplying
factor 0.1405) 2407.28
TOTAL 19540.99 Y
Add 15% CPOH on "Y" 2931.15
TOTAL 22472.13 Z
Add Cess @ 1% on "Z" 224.72
Cost for 6.72 sqm 22696.86
Cost for 1 sqm 3377.51
Say 3377.50
25.4 Extra for openable side / top hung vision glass panels (IGUs) including
providing and supplying at site all accessories and hardwares for the openable
panels as specified and of the approved make such as heavy duty stainless
steel friction hinges, min 4 -point cremone locking sets with stainless steel
plates, handles, buffers etc. including necessary stainless steel screws/
fasteners, nuts, bolts, washers etc. all complete as per the Architectural
drawings, as per the approved shop drawings, as specified and as directed
by the Engineer- in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1.76 sqm
Width of the unit 1.6 m
Shuttter Weight
Height of the unit 1.1 m
Outer glass 6 mm
Area 1.76 sqm
Inner glass 6 mm
Aluminium Weight per sqm 7.78 Kg
Al weight = 1.76x7.78 = 13.7 Kg
No of Locking Point 4 no Total 67 Kg
Wedge Block 1 no
Details of cost for 1.76 sqm
MATERIALS
2619 6 mm thick clear heat strengthened glass each 3.00 132.00 396.00
2611 EPDM Gasket in Kg (Above 60 g / m) kg 0.80 156.00 124.80
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2041
Code Description Unit Quantity Rate Amount
2614 SS Screws of sizes for structural
glazing / ACP Cladding each 49.00 4.00 196.00
2615 Protective Tape metre 1.76 22.00 38.72
2620 ARMS GS HD -TOP HUNG -20"-TYPE
P-COUPLE pair 1.00 1390.00 1390.00
2621 Connection Block each 2.00 36.00 72.00
2622 Curtain wall striker each 4.00 87.00 348.00
2623 Adjustable Fastening Pawl each 4.00 36.00 144.00
2624 Corner drive each 2.00 260.00 520.00
2625 Top wedge Block each 1.00 122.00 122.00
9999 Sundries L.S. 118.00 2.12 250.16
9999 Sundries (For Fabrication) L.S. 354.36 2.12 751.24
TOTAL 4352.92 W
Add 1 % Water charges on "W" 43.53
TOTAL 4396.45 X
Add GST on "X" (multiplying
factor 0.1405) 617.70
TOTAL 5014.15 Y
Add 15% CPOH on "Y" 752.12
TOTAL 5766.28 Z
Add Cess @ 1% on "Z" 57.66
Cost for 1.76 sqm 5823.94
Cost for 1 sqm 3309.06
Say 3309.05
25.5 Providing, fabricating and supplying shadow box of required size and shape,
for fixing in the spandrel portion of the structural glazing, in linear as well as
curvilinear portions of the building by providing semi -rigid, inorganic, non-
combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183
and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on
surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass
tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /
sqm, made of randomly oriented glass fibres distributed in a binder by a wet-
lay process including fixing 1.5 mm thick solid aluminum sheet backing using,
6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.
Code Description Unit Quantity Rate Amount
Details of cost for 3.23 sqm
Width of the unit = 0.86 m
Height of the unit = 3.75 m
Area = 3.23 sqm
Area including wastage @5 % = 3.39
Details of cost for 3.23 sqm
MATERIALS
2626 Glass wool Denisity 48 Kg / m3 with
Black Glass Tissue (BGT) sqm 3.39 255.00 864.45
2634 GI/Aluminium Sheet (0.8 mm thick) kg 21.30 55.00 1171.50
2627 SS Screws - # 8 x 19 each 32.00 7.00 224.00
2628 Weather Sealant - DC 789 cartridge 2.00 125.00 250.00
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2042
Code Description Unit Quantity Rate Amount
2629 Cement Board sqm 3.39 245.00 830.55
9999 Sundries with clips & adhesives L.S. 308.50 2.12 654.02
9999 Sundries (For Fabrication) L.S. 170.64 2.12 361.76
9999 Sundries (For Installation) L.S. 170.64 2.12 361.76
TOTAL 4718.03 W
Add 1 % Water charges on "W" 47.18
TOTAL 4765.21 X
Add GST on "X" (multiplying
factor 0.1405) 669.51
TOTAL 5434.73 Y
Add 15% CPOH on "Y" 815.21
TOTAL 6249.94 Z
Add Cess @ 1% on "Z" 62.50
Cost for 3.23 sqm 6312.43
Cost for 1 sqm 1954.31
Say 1954.30
25.6 Providing and supplying Spandrel Glass Panels comprising of 6 mm thick
heat strengthened monolithic float glass of approved colour and shade with
reflective soft coating on surface # 2 of approved colour and shade so as to
match the colour and shade of the IGUs in the vision panels etc. ,all complete
for the required performances as specified, as per the Architectural drawings,
as per the approved shop drawings, as specified, and as directed by the
Engineer- in- Charge.
For payment, only the actual area of glass on face # 1 of the glass panels (but
excluding the area of grooves and weather silicone sealant) provided and fixed
in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass
Panels in the curtain glazing is included in cost of relevent Item*).“(i) Coloured
tinted float glass 6mm thick substrate with reflective soft coating on face # 2,
having properties as visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. . The properties of
performance glass shall be decided by technical sanctioning authority as per
the site requirement.
Code Description Unit Quantity Rate Amount
Details of cost for 3.23 sqm
Width of the unit = 0.86 m
Height of the unit = 3.75 m
Area = 3.23 sqm
Area i/c wastage @ 5 % = 3.39 sqm
Details of cost for 3.23 sqm
MATERIALS
2617 6 mm thick High performance glass sqm 3.39 1030.00 3491.70
9999 Sundries (Insurance charges) L.S. 43.46 2.12 92.14
9999 Sundries (Fabrication charges including
silicon sealant, baker rod, desecant etc.) L.S. 682.55 2.12 1447.01
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2043
Code Description Unit Quantity Rate Amount
9999 Sundries (transporation including loading
& unloading) L.S. 147.59 2.12 312.89
TOTAL 5343.73 W
Add 1 % Water charges on "W" 53.44
TOTAL 5397.17 X
Add GST on "X" (multiplying
factor 0.1405) 758.30
TOTAL 6155.47 Y
Add 15% CPOH on "Y" 923.32
TOTAL 7078.79 Z
Add Cess @ 1% on "Z" 70.79
Cost for 3.23 sqm 7149.58
Cost for 1 sqm 2213.49
Say 2213.50
25.8 Design supply & installation of suspended Spider Glazing system designed
to withstand the wind pressure as per IS 875 (Part-III). The Suspended System
held with Spider Fittings of SS-316 Grade Steel of approved manufacturer
with glass panel having 12 mm thick clear toughened glass held together with
SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass
fins 21 mm thick. The Glass fins and glass panel assembly shall be connected
to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor
bolts and at the bottom using SS channel of 50x25x2mm using fastener &
anchor bolts, non staining weather sealants of approved make, Teflon/ nylon
bushes and separators to prevent bi-metallic contacts, all complete to perform
as per specification and approved drawings. The complete system to be
designed to accommodate thermal expansion & seismic movements etc. The
joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U
channel of the assembly to be filled with non staining weather sealant, so as
to make the entire system fully water proof & dust proof.
The rate shall include all design, Engineering and shop drawing including
approval from structural designer, labour, T&P, scaffolding, other incidental
charges including wastage, enabling temporary services all fitting fixers nut
bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass
etc. all complete. For the purpose of payment, actual elevation area of Glazing
including thickness of joints and the portion of Glass panel inside the SS
channel shall be measured.
Code Description Unit Quantity Rate Amount
Details of cost for 35.28 Sqm
Description WD HT Nos Area
(Sqm)
Facade Area 7.00 5.04 1.00 35.28
Fin Area 0.40 2.30 5.00 4.60
(A) Spider Fitting
8945 4 Point spider fittings of SS-316 grade
with fin but without flat head bolt(c/c
routel distance 200mm) each 5.00 3318.00 16590.00
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2044
Code Description Unit Quantity Rate Amount
8946 2 Point wall mounted spider fitting of
SS- 316 grade without flat head bolt
and anchor fastener (c/c routel
distance 200mm) each 2.00 1659.00 3318.00
8947 1 Point wall mounted spider fitting of
SS-316 grade without flat head bolt and
anchor fastener (c/c routel distance
200mm) each 12.00 1300.00 15600.00
8948 Flate head bolt Nos 36.00 651.00 23436.00
8949 400 mm long fin plate without fastners pair 5.00 5931.00 29655.00
(B) Local Hardware
2612 Anchor Fastner - M10
For one point spider fitting =12x2=24 nos
For two point spider fitting =2x2=4 nos
For 400mm fin plates =5x6=30 nos
Total=58 nos each 58.00 11.00 638.00
8560 Non staining water resistant Clear
silicon filling in gap metre 49.28 70.00 3449.60
Vr. joints between glasses
= 7x5.04=35.28 m
Hr.joints between glass & wall =
2x7.00=14.00 mTotal=49.28 m
8559 Stainless steel U Channel of size
(50x25x2mm) metre 7.00 160.00 1120.00
9999 Sundries(Baker Road, Screw &
Accessories) L.S. 1000.00 2.12 2120.00
9999 Labour L.S. 10000.00 2.12 21200.00
9999 Scaffolding L.S. 2600.00 2.12 5512.00
(C) Glass Area
8778 Toughened glass 12 mm thickness sqm 37.04 1750.00 64820.00
with hole =7.00x5.04=35.28 sqm +
1.76 sqm (Add 5% Wastage)
Total = 37.04 sqm
2415 21mm thick clear toughened Laminated
glass for fins with holes sqm 4.83 6120.00 29559.60
= 5x2.30x.40=4.60sqm + 0.23sqm
(Add 5% Wastage)Total = 4.83 sqm
TOTAL 217018.20 W
Add 1 % Water charges on "W" 2170.18
TOTAL 219188.38 X
Add GST on "X" (multiplying
factor 0.1405) 30795.97
TOTAL 249984.35 Y
Add 15% CPOH on "Y" 37497.65
TOTAL 287482.00 Z
Add Cess @ 1% on "Z" 2874.82
Cost of 35.28 sqm 290356.82
Cost of 1 sqm 8230.07
Say 8230.05
SUB HEAD : 25- STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
2045
SUB HEAD : 26.0
NEW TECHNOLOGIES AND
MATERIALS
2047
26.1 Providing & fixing in position Phenol bonded Bamboowood flooring with
planks of sizes 14mm thick, minimum 1800mm length and minimum 100 mm
wide, in approved colour, texture and finish, having Performance Appraisal
Certificate (PAC) issued by Building Materials & Technology Promotion
Council (BMTPC). The flooring shall be fixed with tongue and groove
interlocking system, with underlayment of 4mm thick expanded polyethylene
foam sheets having density 40kg/cum, over prepared surface with necessary
quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm
x 44mm, wherever required. The bamboowood planks shall have minimum
density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV
coating, all complete as per direction of the Engineer in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10m x 10m = 100 sqm
MATERIAL
8021 Bamboo wood Tile Flooring 14mm
thick, minimum 1800 mm length and
100 mm wide sqm 110.00 3470.00 381700.00
100 + 10 (Add for wastage @10%)
= 110 sqm
8022 Bamboo wood Quarter Round 18mm
thick of size 1900mm x 18mm metre 39.90 115.00 4588.50
8023 Bamboo wood door reducer 14mm thick
of size 1900mm x 44mm metre 2.00 255.00 510.00
8015 Expanded polyethylene Foam sheet
4mm thick of Density 40kg/m3 sqm 105.00 20.00 2100.00
100 + 5 (Add for wastage @5%)
= 105 sqm
1246 Silicon based Joint Sealant for Tiles kg 5.00 160.00 800.00
1247 Rubber base Adhesive kg 5.00 223.00 1115.00
LABOUR
0111 Carpenter 1st class day 3.00 784.00 2352.00
0114 Beldar day 3.00 645.00 1935.00
9999 Sundries L.S. 100.00 2.12 212.00
TOTAL 395312.50 W
Add 1 % Water charges on "W" 3953.13
TOTAL 399265.63 X
Add GST on "X" (multiplying
factor 0.1405) 56096.82
TOTAL 455362.45 Y
Add 15% CPOH on "Y" 68304.37
TOTAL 523666.81 Z
Add Cess @ 1% on "Z" 5236.67
Cost of 100 sqm 528903.48
Cost of 1 sqm 5289.03
Say 5289.05
26.2 Providing & fixing in position Phenol bonded Bamboo wood in wall skirting
with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm
wide(minimum), in approved colour, texture and finish, having Performance
Appraisal Certificate (PAC) issued by Building Materials & Technology
Promotion Council (BMTPC). The skirting shall be fixed with SS screws &
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2049
rawl plugs, over underlayment of 4mm thick, expanded polyethylene foam
sheets having 40kg/cum density over prepared surface. The bamboowood
planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000
Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer
in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm skirting
MATERIAL
8024 Bamboo wood Skirting 14mm thick of
Size 1900mm x 85mm metre 120.59 300.00 36177.00
Area of 1 length skirting is 1.9 m x
0.085 m = 0.162 sqm
Quantity required for 10 sqm
= 10 / 0.1615 = 61.92 pieces
Add 2.5% wastage= 1.548
Total = 61.92 + 1.548 = 63.468
Qty in running mtr = 63.468 x1.9m
= 120.59 running meter
8015 High Density Expanded poly ethylene
Foam sheet 4mm thick of Density
40kg/m3 sqm 10.50 20.00 210.00
10 + 0.5 (Add for wastage @5%)
= 10.5 sqm
8210 Stainless steel screws 50 mm 100 Nos 1.86 300.00 558.00
(62x3=186 nos)
1246 Silicon based Joint Sealant for Tiles kg 1.00 160.00 160.00
1247 Rubber base Adhesive kg 1.00 223.00 223.00
LABOUR
0111 Carpenter 1st class day 1.00 784.00 784.00
0114 Beldar day 1.00 645.00 645.00
9999 Sundries L.S. 20.00 2.12 42.40
TOTAL 38799.40 W
Add 1 % Water charges on "W" 387.99
TOTAL 39187.39 X
Add GST on "X" (multiplying
factor 0.1405) 5505.83
TOTAL 44693.22 Y
Add 15% CPOH on "Y" 6703.98
TOTAL 51397.21 Z
Add Cess @ 1% on "Z" 513.97
Cost of 10 sqm 51911.18
Cost of 1 sqm 5191.12
Say 5191.10
26.3 Providing & fixing in position Phenol bonded Bamboowood wall cladding at
all height with planks of sizes 10mm thick, minimum 1800mm length and
minimum 100 mm wide, in approved colour, texture and finish, having
Performance Appraisal Certificate (PAC) issued by Building Materials &
Technology Promotion Council (BMTPC), with necesasary profiled edges fixed
with 40mm SS screws 5 nos in each tile to frame work made of second class
teak wood of size 20x15 mm in centre of each tile and bottom and top of work
height, 40x15mm placed at ends of each tile. The cladding shall be laid over
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2050
backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/
cum in two layers, first layer on wall surface before fixing wooden frame and
second layer on frame under cladding. The bamboowood planks shall have
minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco
friendly UV coating, all complete as per direction of the Engineer in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10m x 9.5m = 95 sqm
MATERIAL
8025 Bamboo wood Tile Wall Cladding
10mm thick, minimum 1800 mm length
and minimum 100 mm wide sqm 104.50 3400.00 355300.00
10 x 9.5 = 95 + 9.5 (Add for wastage
@10%) = 104.5 sqm
8026 Bamboo wood T-mold 14mm thick of
size 1900mm x 44mm metre 41.62 250.00 10405.00
At end joints of planks = 4x9.91 =
39.64 mtr + 1.98 (Add for wastage 5%)
= 41.62 mtr
8027 Bamboo wood Threshold 14mm thick
of size 1900mm x 44mm metre 40.95 255.00 10442.25
At perriferi of cladding = 2x(10+9.5)
+1.95 (Add for wastage @5%)
=40.95 metre
8016 High Density expanded poly ethylene
(EPE) Foam 1mm thick sqm 199.50 10.00 1995.00
(2x10x9.5) = 190 + 9.5 (Add for
wastage @5%)=199.5 sqm
8210 Stainless steel screws 50 mm 100 Nos 2.58 300.00 774.00
@500mm c/c at teak wood frame
8212 Stainless steel screws 30 mm 100 Nos 18.50 230.00 4255.00
(5nos in each panels)
No of panels=95/(1.9 x 0.135)=370 nos
No. of screws= 370 x 5=1850 nos
1190 Second class teak wood in planks 10 cudm 5.2866 791.00 4181.70
10 metre height, at every 1.9 meter
height one length of 10 metre i.e
(5x9.91x0.02x 0.015+2x10x0.02x.015+
2x9.50x.02x.015+4x9.91x0.04x0.015)+
wastage @5% =0.052866 cum cudm
LABOUR
0111 Carpenter 1st class day 5.00 784.00 3920.00
0112 Carpenter 2nd class day 5.00 714.00 3570.00
0114 Beldar day 5.00 645.00 3225.00
9999 Sundries L.S. 100.00 2.12 212.00
TOTAL 398279.95 W
Add 1 % Water charges on "W" 3982.80
TOTAL 402262.75 X
Add GST on "X" (multiplying
factor 0.1405) 56517.92
TOTAL 458780.67 Y
Add 15% CPOH on "Y" 68817.10
TOTAL 527597.77 Z
Add Cess @ 1% on "Z" 5275.98
Cost of 95 sqm 532873.74
Cost of 1 sqm 5609.20
Say 5609.20
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2051
26.4 Providing & fixing in position Phenol bonded Bamboowood panelled or
panelled and glazed shutters for doors windows, clerestorey windows with
pre-molded minimum 30mm thick planks, in approved colours, texture & finish.
It shall have 10mm wide, 25mm deep grove to fit in panels.The bamboo wood
shall have minimum density of 1000 Kg/cum, minimum Hardness 1000 Kgf. All
styles and rails shall have profiled interlocking system locked in place by
bamboo pins, all complete as per direction of Engineer in charge. (The
panelling will be paid for separately).
Code Description Unit Quantity Rate Amount
Details of cost for shutters of
Bamboowood 200 x 108cm = 2.16 sqm
MATERIAL
8028 Bamboo wood shutter of doors 10 cudm 4.83 1700.00 8211.00
Styles 4x2.00x0.115x0.03
=0.0276 cum +
Top rails 1x1.08x0.11x0.03m
= 0.0036 cum +
Bottom rails 1x1.08x0.212x0.03
= 0.0069 cum +
Lock rails 1x1.08x0.18x0.03
= 0.0058 cum
Total =0.0439 cum + 0.004 cum
(Wastage @5%)
Grand Total =0.0483 cum OR
48.30 cudm
8215 Stainless steel butt hinges 125x64x
1.9 mm IS : 12817 marked 10 Nos 0.40 310.00 124.00
8211 Stainless steel screws 40 mm 100 Nos 0.32 250.00 80.00
LABOUR
0156 Carpenter (average) day 0.33 749.00 247.17
0114 Beldar day 0.33 645.00 212.85
9999 Sundries T&P etc. L.S. 5.62 2.12 11.91
TOTAL 8886.93 W
Add 1 % Water charges on "W" 88.87
TOTAL 8975.80 X
Add GST on "X" (multiplying
factor 0.1405) 1261.10
TOTAL 10236.90 Y
Add 15% CPOH on "Y" 1535.54
TOTAL 11772.44 Z
Add Cess @ 1% on "Z" 117.72
Cost of 2.16 sqm 11890.16
Cost of 1 sqm 5504.71
Say 5504.70
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2052
26.5 Providing & fixing in position Phenol bonded Bamboo wood panelling of 10mm
thick, in 25 to 40 mm thick panelled or panelled & glazed shutters for doors,
windows, clerestorey windows, in approved colour, texture & finish. The
bamboowood planks shall have minimum density of 1000 Kg/cum & minimum
Hardness 1000 Kgf. The panels shall have profiled interlocking system locked
in place with bamboo pins all complete as per direction of the Engineer in-
charge. (area of opening for panel inserts excluding portion inside grooves
or rebates to be measured)
Code Description Unit Quantity Rate Amount
Details of cost for shutters of a door
with 2/3rd panelling…
200 x 108 cm = 2.16 sqm
Panel area = 4x45.1x36.55cm
= 0.66 sqm
MATERIAL
8029 Bamboo wood panelling (10mm thick) 10 cudm 0.80 1680.00 1344.00
4x47.2x38.65x1.0cm = 0.0073cum
+ 0.0007 sqm (Add Wastage @10%)
Total = 0.008 cum OR 8 cudm
LABOUR
0156 Carpenter (average) day 0.57 749.00 426.93
9999 Sundries L.S. 4.42 2.12 9.37
TOTAL 1780.30 W
Add 1 % Water charges on "W" 17.80
TOTAL 1798.10 X
Add GST on "X" (multiplying
factor 0.1405) 252.63
TOTAL 2050.74 Y
Add 15% CPOH on "Y" 307.61
TOTAL 2358.35 Z
Add Cess @ 1% on "Z" 23.58
Cost of 0.66 sqm 2381.93
Cost of 1 sqm 3608.99
Say 3609.00
26.6 Providing & fixing in position 65 mm thick factory made door frame of Phenol
bonded Bamboo wood (superior class, interior use), in approved colour, texture
and finish.The bamboo wood shall have minimum density of 1000 Kg/cum,
minimum hardness 1000 Kgf. The door frame shall have tenon & mortise
interlocking system, to be fixed to the wall with 100 mm size G.I screws all a
complete as per direction of Engineer-in charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 33 cudm
MATERIAL
8030 Superior class Bamboo wood door
frame 65 mm thick 10 cudm 3.40 1675.00 5695.00
2x206.75x9.5x6.5 cm = 0.0255 cum +
1x117.50x9.5x6.5 cm = 0.0072 cum
Total = 0.033 cum = 33 cudm
+ 0.001 cum (Add for wastage @ 5%)
Grand total = 0.034 cum = 34 Cudm
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2053
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 0.72 784.00 564.48
0114 Beldar day 0.07 645.00 45.15
TOTAL 6304.63 W
Add 1 % Water charges on "W" 63.05
TOTAL 6367.68 X
Add GST on "X" (multiplying
factor 0.1405) 894.66
TOTAL 7262.33 Y
Add 15% CPOH on "Y" 1089.35
TOTAL 8351.69 Z
Add Cess @ 1% on "Z" 83.52
Cost of 33 cudm 8435.20
Cost of 1 cudm 255.61
Say 255.60
26.6A Providing, erecting, laying and fixing in position in 3.5 to 4 mm thick bamboo
mat corrugated sheet (BMCS) as per IS: 15476-2004 in roofing with self drilling
screws along with EPDM washers complete or with galvanized iron J or L
hooks 8mm dia G.I. plain and bitumen washers etc, all complete as per direction
of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 181.30sqm area.
Consider a sheet of 18mx9m (external
dimension of plinth). Area of roof =
18.5x9.8m = 181.30 sqm.
MATERIAL:
Sheets used = 2x 19 nos (2.44m x
1.05m) & 4x19 nos (1.83mx 1.05m).
Total area =
(2x19x2.44x1.05)+(4x19x1.83x1.05) =
243.39sqm, Add wastage @ 3% =
7.30 sqm, Total area = 250.69 sqm.
8144 Bamboo Mat corrugated sheets 3.5 to
4mm thick conforming to
IS 15476:2004 sqm 250.69 2648.00 663827.12
Weight of sheets, For 2.44mx1.05m
sheet size, 12kg/Nos x 38 nos = 456
kgs, For 1.83m x 1.05m sheet size,
9kgs/Nos x 76 Nos = 684 kgs. Total
weight of sheet = 456+684 = 1140 kgs
= 1.14 tonne
2358 Carriage of Bamboo Mat corrugated
sheets and accessories tonne 1.14 17700.00 20178.00
1023 Galvanized steel J or L hooks 8mm dia 10 Nos 68.40 120.00 8208.00
1208 Bitumen washer 100 Nos 6.84 30.00 205.20
1209 G.I. plain washer thick 100 Nos 6.84 35.00 239.40
9977 Carriage of bolts and washers L.S. 11.58 2.12 24.55
9999 Sundries L.S. 56.78 2.12 120.37
LABOUR:
0130 Mistry day 3.00 784.00 2352.00
0112 Carpenter 2nd class day 3.00 714.00 2142.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2054
Code Description Unit Quantity Rate Amount
0114 Beldar day 9.00 645.00 5805.00
TOTAL 703101.64 W
Add 1 % Water charges on "W" 7031.02
TOTAL 710132.66 X
Add GST on "X" (multiplying
factor 0.1405) 99773.64
TOTAL 809906.30 Y
Add 15% CPOH on "Y" 121485.94
TOTAL 931392.24 Z
Add Cess @ 1% on "Z" 9313.92
Cost of 181.30 sqm 940706.17
Cost of 1sqm 5188.67
Say 5188.65
26.6B Providing and fixing in position ridges of 3.5 to 4 mm thick bamboo mat ridge
cap (BMRC) as per IS: 15476-2004 in roofing with self drilling screws along
with EPDM washers complete or with galvanized iron J or L hooks 8mm dia
G.I. plain and bitumen washers etc, all complete as per direction of Engineer-
in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for length of ridge
18.50 metre (pair of 43cm width each)
Consider a shed of 18mx9m (external
dimensions of plinth). Length of ridge
18.50 metre.
MATERIAL:
Ridges (Male & female) of size: 1.05m
length required = 20 sets x 1.05m =
21.00 metre, Add wastage @ 5% =
1.05 metre, Total length = 22.05 metre.
8145 Bamboo Mat Ridge cap 3.5 to 4mm
thick conforming to IS 15476:2004 metre 22.05 2570.00 56668.50
9977 Carriage (The ridges to be fixed with
the same hooks as the sheets) L.S. 19.43 2.12 41.19
9999 Sundries L.S. 9.71 2.12 20.59
LABOUR:
0130 Mistry day 0.20 784.00 156.80
0112 Carpenter 2nd class day 0.20 714.00 142.80
0114 Beldar day 0.60 645.00 387.00
TOTAL 57416.88 W
Add 1 % Water charges on "W" 574.17
TOTAL 57991.05 X
Add GST on "X" (multiplying
factor 0.1405) 8147.74
TOTAL 66138.79 Y
Add 15% CPOH on "Y" 9920.82
TOTAL 76059.61 Z
Add Cess @ 1% on "Z" 760.60
Cost of 18.50 metre 76820.20
Cost of 1 metre 4152.44
Say 4152.45
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2055
26.6C Providing and fixing at all height false ceiling of 4mm thick phenol bonded
Bamboo Mat board (595x595mm) conforming to IS:13958-1994 including
providing and fixing of frame work made of GI angle 25x25x0.4 mm thick all
around suitably fixed to wall with the help of dash fastener and hanger frame
(600x600 c/c) made GI slotted Tee having powder coating on bottom side
(30x25x0.3 mm thick for main member & 25x25x0.3 mm for cross member)
connected to ceiling with 2.64mm GI wire and anchor fastener at every junction
and also including cost of making openings for light fittings, grills, diffusers,
cut outs made with frame of perimeter channels suitably fixed all complete as
per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm.
Ceiling area = 100sqm, Add wastage
@ 5% = 5sqm, Total area = 105 sqm
MATERIAL:
8147 4mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 105.00 1738.00 182490.00
Weight: (0.595x0.595m of Bamboo
board). Total number of board = 297.
Total weight of Bamboo board = 297
Nos x 1.31kgs/Nos = 389.07 kgs =
0.39 tonne.
2358 Carriage of 4mm thick Bamboo mat
board and accessories. tonne 0.39 17700.00 6903.00
8570 GI Main T ceiling section 30x25x0.3
mm (3 metre long) including of wastage
of 10% each 29.50 210.00 6195.00
8571 GI Perimeter wall angle 25x25x0.4 mm
(3 metre long) including of wastage of
10% each 13.50 170.00 2295.00
8572 GI Intermediate cross T section
25x25x0.3 mm (1.2 metre long)
including of wastage of 10% on grid
cutouts. each 147.00 80.00 11760.00
8573 GI Intermediate cross T section
25x25x0.3 mm (0.6 metre long)
including of wastage of 10% on grid
cutouts. each 147.00 35.00 5145.00
8615 Hanger rod 4mm thick each 72.00 10.00 720.00
8616 Adjustment clip 85x30x0.8mm each 72.00 6.00 432.00
7015 Soffit cleat (size 27x37x25x1.60mm) each 72.00 3.00 216.00
7388 Dash hold fasteners 12.5mm dia,
50mm long with 6mm dia bolts each 72.00 10.00 720.00
9977 Carriage of grid materials L.S. 89.28 2.12 189.27
9999 Sundries L.S. 187.95 2.12 398.45
LABOUR:
0112 Carpenter 2nd class day 28.00 714.00 19992.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2056
Code Description Unit Quantity Rate Amount
0114 Beldar day 23.00 645.00 14835.00
TOTAL 252290.73 W
Add 1 % Water charges on "W" 2522.91
TOTAL 254813.63 X
Add GST on "X" (multiplying
factor 0.1405) 35801.32
TOTAL 290614.95 Y
Add 15% CPOH on "Y" 43592.24
TOTAL 334207.19 Z
Add Cess @ 1% on "Z" 3342.07
Cost of 100 sqm 337549.27
Cost of 1sqm 3375.49
Say 3375.50
26.6D Providing and fixing at Bamboo Mat board conforming to IS:13958-1994 for
partition to frame by bucking or studding with screws etc. complete (Frames,
backing or studding to be paid separately)
26.6D.1 3mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for 3.5mx2m = 7.0 sqm
Partition area = 7.0sqm, Add wastage
@ 5% = 0.35sqm, Total area = 7.35 sqm
MATERIAL:
8146 3mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 7.35 1508.00 11083.80
Weight: 7.35sqm x 2.70 kgs/sqm
=19.845 kgs = 0.02 tonne.
2358 Carriage of 3mm thick Bamboo mat
board and accessories. tonne 0.02 17700.00 354.00
9999 Sundries and screws L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 12782.45 W
Add 1 % Water charges on "W" 127.82
TOTAL 12910.27 X
Add GST on "X" (multiplying
factor 0.1405) 1813.89
TOTAL 14724.17 Y
Add 15% CPOH on "Y" 2208.63
TOTAL 16932.79 Z
Add Cess @ 1% on "Z" 169.33
Cost of 7 sqm 17102.12
Cost of 1sqm 2443.16
Say 2443.15
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2057
26.6D.2 4mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for 3.5mx2m = 7.0 sqm
Partition area = 7.0sqm, Add wastage
@ 5% = 0.35sqm, Total area = 7.35 sqm
MATERIAL:
8147 4mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 7.35 1738.00 12774.30
Weight: 7.35sqm x 3.70 kgs/sqm
=27.195 kgs = 0.03 tonne.
2358 Carriage of 4mm thick Bamboo mat
board and accessories. tonne 0.03 17700.00 531.00
9999 Sundries and screws L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 14649.95 W
Add 1 % Water charges on "W" 146.50
TOTAL 14796.45 X
Add GST on "X" (multiplying
factor 0.1405) 2078.90
TOTAL 16875.35 Y
Add 15% CPOH on "Y" 2531.30
TOTAL 19406.65 Z
Add Cess @ 1% on "Z" 194.07
Cost of 7 sqm 19600.72
Cost of 1sqm 2800.10
Say 2800.10
26.6D.3 6mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for 3.5mx2m = 7.0 sqm
Partition area = 7.0sqm, Add wastage
@ 5% = 0.35sqm, Total area = 7.35 sqm
MATERIAL:
8148 6mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 7.35 2098.00 15420.30
Weight: 7.35sqm x 5.40 kgs/sqm
=39.69 kgs = 0.04 tonne.
2358 Carriage of 6mm thick Bamboo mat
board and accessories. tonne 0.04 17700.00 708.00
9999 Sundries and screws L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 17472.95 W
Add 1 % Water charges on "W" 174.73
TOTAL 17647.68 X
Add GST on "X" (multiplying
factor 0.1405) 2479.50
TOTAL 20127.18 Y
Add 15% CPOH on "Y" 3019.08
TOTAL 23146.25 Z
Add Cess @ 1% on "Z" 231.46
Cost of 7 sqm 23377.72
Cost of 1sqm 3339.67
Say 3339.65
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2058
26.6D.4 9mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for 3.5mx2m = 7.0 sqm
Partition area = 7.0sqm, Add wastage
@ 5% = 0.35sqm, Total area = 7.35 sqm
MATERIAL:
8149 9mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 7.35 2688.00 19756.80
Weight: 7.35sqm x 8.40 kgs/sqm
=61.74 kgs = 0.06 tonne.
2358 Carriage of 9mm thick Bamboo mat
board and accessories. tonne 0.06 17700.00 1062.00
9999 Sundries and screws L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 22163.45 W
Add 1 % Water charges on "W" 221.63
TOTAL 22385.08 X
Add GST on "X" (multiplying
factor 0.1405) 3145.10
TOTAL 25530.19 Y
Add 15% CPOH on "Y" 3829.53
TOTAL 29359.72 Z
Add Cess @ 1% on "Z" 293.60
Cost of 7 sqm 29653.31
Cost of 1sqm 4236.19
Say 4236.20
26.6D.5 12mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for 3.5mx2m = 7.0 sqm
Partition area = 7.0sqm, Add wastage
@ 5% = 0.35sqm, Total area = 7.35 sqm
MATERIAL:
8150 12mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 7.35 3115.00 22895.25
Weight: 7.35sqm x 10.00 kgs/sqm
=73.50 kgs = 0.07 tonne.
2358 Carriage of 12mm thick Bamboo mat
board and accessories. tonne 0.07 17700.00 1239.00
9999 Sundries and screws L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 0.90 714.00 642.60
0114 Beldar day 1.00 645.00 645.00
TOTAL 25478.90 W
Add 1 % Water charges on "W" 254.79
TOTAL 25733.69 X
Add GST on "X" (multiplying
factor 0.1405) 3615.58
TOTAL 29349.27 Y
Add 15% CPOH on "Y" 4402.39
TOTAL 33751.66 Z
Add Cess @ 1% on "Z" 337.52
Cost of 7 sqm 34089.18
Cost of 1sqm 4869.88
Say 4869.90
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2059
26.6E Providing and fixing at all height wall panelling with phenol bonded Bamboo
Mat board conforming to IS:13958-1994 including providing and fixing to frame
work made of 50mm x 50mm hardwood plugs including cutting brick work
and fixing in cement mortar and making good the wall etc. and also providing
and fixing wooden moulded corner beading of triangular shape to the junction
of panelling etc. with iron screws all complete as per direction of Engineer-in-
Charge.
26.6E.1 9mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for panelling area of
5mx4m = 20.00 sqm with moulding
length of 18.00 metre
Wall panelling area = 20.00sqm, Add
wastage @ 5% = 1.0sqm, Total area
= 21.00 sqm
MATERIAL:
8149 9mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 21.00 2688.00 56448.00
Weight: 21sqm x 8.40 kgs/sqm
=176.4 kgs = 0.18 tonne.
2358 Carriage of 9mm thick Bamboo mat
board and accessories. tonne 0.18 17700.00 3186.00
1316 50mmx50mm hardwood plug each 45.00 50.00 2250.00
1190 Second class teak wood in planks 10 cudm 2.477 791.00 1959.31
2204 Carriage of timber cum 0.02477 187.35 4.64
0637 Bright finished or black enamelled
mild steel screws 40mm 100 Nos 0.70 60.00 42.00
9999 Sundries L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0114 Beldar day 2.00 645.00 1290.00
TOTAL 66665.00 W
Add 1 % Water charges on "W" 666.65
TOTAL 67331.65 X
Add GST on "X" (multiplying
factor 0.1405) 9460.10
TOTAL 76791.74 Y
Add 15% CPOH on "Y" 11518.76
TOTAL 88310.50 Z
Add Cess @ 1% on "Z" 883.11
Cost of 20 sqm 89193.61
Cost of 1sqm 4459.68
Say 4459.70
26.6E.2 12mm thickness
Code Description Unit Quantity Rate Amount
Details of cost for panelling area of
5mx4m = 20.00 sqm with moulding
length of 18.00 metre
Wall panelling area = 20.00sqm, Add
wastage @ 5% = 1.0sqm, Total area
= 21.00 sqm
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2060
Code Description Unit Quantity Rate Amount
MATERIAL:
8150 12mm thick Bamboo Mat Board
conforming to IS 13958:1994 sqm 21.00 3115.00 65415.00
Weight: 21sqm x 10 kgs/sqm
=210 kgs = 0.21 tonne.
2358 Carriage of 12mm thick Bamboo mat
board and accessories. tonne 0.21 17700.00 3717.00
1316 50mmx50mm hardwood plug each 45.00 50.00 2250.00
1190 Second class teak wood in planks 10 cudm 2.477 791.00 1959.31
2204 Carriage of timber cum 0.02477 187.35 4.64
0637 Bright finished or black enamelled
mild steel screws 40mm 100 Nos 0.70 60.00 42.00
9999 Sundries L.S. 26.91 2.12 57.05
LABOUR:
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0114 Beldar day 2.00 645.00 1290.00
TOTAL 76163.00 W
Add 1 % Water charges on "W" 761.63
TOTAL 76924.63 X
Add GST on "X" (multiplying
factor 0.1405) 10807.91
TOTAL 87732.54 Y
Add 15% CPOH on "Y" 13159.88
TOTAL 100892.42 Z
Add Cess @ 1% on "Z" 1008.92
Cost of 20 sqm 101901.34
Cost of 1sqm 5095.07
Say 5095.05
26.7 Providing and fixing 50 mm thick extruded polystyrene rigid insulation board
of required size between cavity wall, complying with ISO 4898:2008 & ASTM C
578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C
578 (measured as per IS 3346), compressive strength of > 350 kPa listed as
per ASTM D 1621, density of 34-36 kg/m³ as per ASTM D 1622, water absorptions
? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per
ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent
property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A,
fixed with suitable water based adhesive and fastener, complete in all respect
as per the direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8561 Extruded polystyrene rigid insulation
board 50 mm thick sqm 10.20 550.00 5610.00
including 2% wastage
LABOUR
0111 Carpenter 1st class day 0.25 784.00 196.00
0128 Mate day 0.25 714.00 178.50
0114 Beldar day 0.25 645.00 161.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2061
Code Description Unit Quantity Rate Amount
9999 Sundries (Water based adhesive,
fasteners, scaffolding etc.) L.S. 100.00 2.12 212.00
TOTAL 6357.75 W
Add 1 % Water charges on "W" 63.58
TOTAL 6421.33 X
Add GST on "X" (multiplying
factor 0.1405) 902.20
TOTAL 7323.52 Y
Add 15% CPOH on "Y" 1098.53
TOTAL 8422.05 Z
Add Cess @ 1% on "Z" 84.22
Cost of 10 sqm 8506.27
Cost of 1 sqm 850.63
Say 850.65
26.8 Providing and fixing 50 mm thick extruded polystyrene rigid insulation board
of required size underdeck on ceiling surface, complying with ISO 4898:2008
& ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as
per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa
listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water
absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1
listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576.
Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM
E84 class A, fixed with suitable water based adhesive and fastener, complete
in all respect as per the direction of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8561 Extruded polystyrene rigid insulation
board 50 mm thick sqm 10.20 550.00 5610.00
including 2% wastage
LABOUR
0111 Carpenter 1st class day 0.50 784.00 392.00
0128 Mate day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
9999 Sundries (Water based adhesive,
fasteners, scaffolding etc.) L.S. 100.00 2.12 212.00
TOTAL 6893.50 W
Add 1 % Water charges on "W" 68.94
TOTAL 6962.44 X
Add GST on "X" (multiplying
factor 0.1405) 978.22
TOTAL 7940.66 Y
Add 15% CPOH on "Y" 1191.10
TOTAL 9131.76 Z
Add Cess @ 1% on "Z" 91.32
Cost of 10 sqm 9223.07
Cost of 1 sqm 922.31
Say 922.30
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2062
26.9 Providing and fixing factory made solid Foam uPVC profile for kitchen cabinet
frame (45 x 20 mm) of approved shade, quality and make. The profile shall be
laminated on both sides, made from rigid foam sheets (Single extruded) having
density 600 Kg/cum and the exposed edges sealed with PVC edge beading of
same shade and colour. The frame shall be fire retardent with necessary screw
holding capacity. Frame shall be fixed to wall using Expendable Fastner with
necesary stainless steel screws, all complete as per direction of Engineer-in-
charge.
Code Description Unit Quantity Rate Amount
Details of cost for kitchen cabinate
(2.00 x 0.45)+(2.00+0.615)= 2.13 mtr
MATERIAL
2491 Pre laminated both side solid foam
uPVC profile (45x20mm) metre 2.13 134.00 285.42
2493 PVC edge beading metre 4.26 32.00 136.32
2494 Expandable fastner with plastic sleeve each 8.00 6.00 48.00
8210 Stainless steel screws 50 mm 100 Nos 0.08 300.00 24.00
LABOUR
0111 Carpenter 1st class day 0.10 784.00 78.40
0114 Beldar day 0.10 645.00 64.50
TOTAL 636.64 W
Add 1 % Water charges on "W" 6.37
TOTAL 643.01 X
Add GST on "X" (multiplying
factor 0.1405) 90.34
TOTAL 733.35 Y
Add 15% CPOH on "Y" 110.00
TOTAL 843.35 Z
Add Cess @ 1% on "Z" 8.43
Cost for 2.13 metre 851.78
Cost for 1 metre 399.90
Say 399.90
26.10 Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm
nominal thickness of approved shade, quality and make, made from rigid foam
sheets (Single extruded) having density 600 Kg/cum and laminated on both
side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed
with PVC edge beading of same shade and colour. The shutter shall be fire
retardent having necessary screw holding capacity. Shutter shall be fixed to
frame using approved hinges with necessary stainless steel screws, all
complete as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for of one shutter
0.46 x0.61m =0.281 sqm
MATERIAL
2492 Solid foam uPVC sheet 20mm thick
prelaminated on both side sqm 0.281 2153.00 604.99
2493 PVC edge beading metre 2.13 32.00 68.16
9999 Sundries L.S. 20.00 2.12 42.40
LABOUR
0111 Carpenter 1st class day 0.20 784.00 156.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2063
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.20 645.00 129.00
TOTAL 1001.35 W
Add 1 % Water charges on "W" 10.01
TOTAL 1011.37 X
Add GST on "X" (multiplying
factor 0.1405) 142.10
TOTAL 1153.46 Y
Add 15% CPOH on "Y" 173.02
TOTAL 1326.48 Z
Add Cess @ 1% on "Z" 13.26
Cost for 0.281 sqm 1339.75
Cost for 1 sqm 4767.79
Say 4767.80
26.11 Providing and fixing concealed hinge of approved quality for 19-20mm thick
door with stainless steel screws complete :
Code Description Unit Quantity Rate Amount
Details of cost for 10 nos
MATERIAL
8226 Concealed zinc coated hinges
19-20 mm thick with mounting plate 10 Nos 1.00 460.00 460.00
8210 Stainless steel screws 50 mm 100 Nos 0.80 300.00 240.00
9977 Carriage of material L.S. 2.73 2.12 5.79
LABOUR
0112 Carpenter 2nd class day 0.14 714.00 99.96
0114 Beldar day 0.09 645.00 58.05
TOTAL 863.80 W
Add 1 % Water charges on "W" 8.64
TOTAL 872.44 X
Add GST on "X" (multiplying
factor 0.1405) 122.58
TOTAL 995.01 Y
Add 15% CPOH on "Y" 149.25
TOTAL 1144.26 Z
Add Cess @ 1% on "Z" 11.44
Cost of 10 nos 1155.71
Cost of 1 no 115.57
Say 115.55
26.12 Supplying & laying of bi-axial extruded high modulus polypropylene geogrid
coforming to MORTH SPECIFICATION for base/sub-base reinforcement
having minimum tensile strength 15kN/m in the longitudinal and transverse
direction, with 5kN/m and 7kN/m tensile strength at 2% and 5% strain
respectively in the longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh opening.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm
MATERIAL
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2064
Code Description Unit Quantity Rate Amount
8956 Bi-Axial Extruded GeoGrids of
Minimum Tensile Strength 15 kN/m in
the longitudinal and transverse direction Sqm 300.00 120.00 36000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 3600.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 45869.04 W
Add 1 % Water charges on "W" 458.69
TOTAL 46327.73 X
Add GST on "X" (multiplying
factor 0.1405) 6509.05
TOTAL 52836.78 Y
Add 15% CPOH on "Y" 7925.52
TOTAL 60762.29 Z
Add Cess @ 1% on "Z" 607.62
Cost for 300 Sqm 61369.92
Cost per Sqm 204.57
Say 204.55
26.13 Supplying & laying of bi-axial extruded high modulus polypropylene geogrid
coforming to MORTH SPECIFICATION for base/sub-base reinforcement having
minimum tensile strength 20kN/m in the longitudinal and transverse direction,
with 7kN/m and 14kN/m tensile strength at 2% and 5% strain respectively in
the longitudinal and transverse direction, junction efficiency not less than
95% and with 38mm X 38mm mesh opening.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm
MATERIAL
8957 Bi-Axial Extruded GeoGrids of
Minimum Tensile Strength 20kN/m in
the longitudinal and transverse
direction sqm 300.00 135.00 40500.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2065
Code Description Unit Quantity Rate Amount
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 4050.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 50819.04 W
Add 1 % Water charges on "W" 508.19
TOTAL 51327.23 X
Add GST on "X" (multiplying
factor 0.1405) 7211.48
TOTAL 58538.71 Y
Add 15% CPOH on "Y" 8780.81
TOTAL 67319.51 Z
Add Cess @ 1% on "Z" 673.20
Cost for 300 Sqm 67992.71
Cost per Sqm 226.64
Say 226.65
26.14 Supplying & laying of bi-axial extruded high modulus polypropylene geogrid
coforming to MORTH SPECIFICATION for base/sub-base reinforcement
having minimum tensile strength 30kN/m in the longitudinal and transverse
direction, with 10.5kN/m and 21kN/m tensile strength at 2% and 5% strain
respectively in the longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh opening.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm
MATERIAL
8958 Bi-Axial Extruded GeoGrids of
Minimum Tensile Strength 30kN/m in
the longitudinal and transverse
direction sqm 300.00 205.00 61500.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 6150.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2066
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 73919.04 W
Add 1 % Water charges on "W" 739.19
TOTAL 74658.23 X
Add GST on "X" (multiplying
factor 0.1405) 10489.48
TOTAL 85147.71 Y
Add 15% CPOH on "Y" 12772.16
TOTAL 97919.87 Z
Add Cess @ 1% on "Z" 979.20
Cost for 300 Sqm 98899.07
Cost per Sqm 329.66
Say 329.65
26.15 Supplying & laying of bi-axial extruded high modulus polypropylene geogrid
coforming to MORTH SPECIFICATION for base/sub-base reinforcement
having minimum tensile strength 40kN/m in the longitudinal and transverse
direction, with 14kN/m and 28kN/m tensile strength at 2% and 5% strain
respectively in the longitudinal and transverse direction, junction efficiency
not less than 95% and with 38mm X 38mm mesh opening.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm
MATERIAL
8959 Bi-Axial Extruded GeoGrids of
Minimum Tensile Strength 40kN/m in
the longitudinal and transverse
direction Sqm 300.00 290.00 87000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 8700.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 101969.04 W
Add 1 % Water charges on "W" 1019.69
TOTAL 102988.73 X
Add GST on "X" (multiplying
factor 0.1405) 14469.92
TOTAL 117458.65 Y
Add 15% CPOH on "Y" 17618.80
TOTAL 135077.44 Z
Add Cess @ 1% on "Z" 1350.77
Cost for 300 Sqm 136428.22
Cost per Sqm 454.76
Say 454.75
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2067
26.16 Supplying & laying of drainage composite for use behind walls, between two
different fills, alongside drains of road, below concrete lining of canals etc.
Geocomposite for planar drainage, realized by thermobonding a draining core
in extruded monofilaments with two filtering nonwoven geotextiles that may
also be working as separation or protecting layers. The draining three
dimensional core will have a “W” configuration as longitudinal parallel
channels. Minimum thickness to be 7.2mm, with two filtering UV stabilized
polypropylene nonwoven geotextile of minimum thickness of 0.75mm
charecteristic opening size (O90) of 110 micron and tensile strength of 8.0 kN/
m that will be working as separation or protecting layer, geocomposite having
in plane flow capacity of 2.1 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa
pressure and tensile strength of 18 kN/m , with mass per unit area of 740 gsm,
supplied in the form of roll for easy transportation to site of work as per detailed
specification all complete as per directions of Engineer in charge.
Code Description Unit Quantity Rate Amount
Material
Details of Cost for 300 Sqm
8960 Geosynthetic Drainage Composite sqm 300.00 530.00 159000.00 P
Add 10 per cent of the cost of
synthetic Composits for wastage and
accessories for joining sheets with the
facia pannels, overlaps and other
protective elements for synthetic
Composits and other miscelleneus
activities required to complete the item
in all respect including transpotarion &
takes. 10% of "P" 15900.00
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 181169.04 W
Add 1 % Water charges on "W" 1811.69
TOTAL 182980.73 X
Add GST on "X" (multiplying
factor 0.1405) 25708.79
TOTAL 208689.52 Y
Add 15% CPOH on "Y" 31303.43
TOTAL 239992.95 Z
Add Cess @ 1% on "Z" 2399.93
Cost for 300 Sqm 242392.88
Cost per Sqm 807.98
Say 808.00
26.17 Supplying & laying of drainage composite for use behind walls, between two
different fills, alongside drains of road, below concrete lining of canals etc.
having thermobonding a draining core - HDPE geonet comprises of two sets
of parallel overlayed ribs integrally connected to have a rhomboidal shape
with a polyethylene film and a nonwoven geotextile having mass per unit
area 130 gsm and tensile strength of 8.0 kN/m that will be working as
separation or protecting layer, geocomposite having in plane flow capacity of
0.7 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2068
of 13.5 kN/m , with mass per unit area of 830 gsm, at easily accessible location
including top and bottom, with all leads and lifts, manpower and machinery,
materials, labour etc. complete and as directed by Engineer - In - Charge.
Code Description Unit Quantity Rate Amount
Material
Details of Cost for 300 Sqm
8961 Geosynthetic Drainage Composite sqm 300.00 630.00 189000.00 P
Add 10 per cent of the cost of
synthetic Composits for wastage and
accessories for joining sheets with the
facia pannels, overlaps and other
protective elements for synthetic
Composits and other miscelleneus
activities required to complete the item
in all respect including transpotarion &
takes. 10% of "P" 18900.00
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 214169.04 W
Add 1 % Water charges on "W" 2141.69
TOTAL 216310.73 X
Add GST on "X" (multiplying
factor 0.1405) 30391.66
TOTAL 246702.39 Y
Add 15% CPOH on "Y" 37005.36
TOTAL 283707.75 Z
Add Cess @ 1% on "Z" 2837.08
Cost for 300 Sqm 286544.82
Cost per Sqm 955.15
Say 955.15
26.18 Supplying and laying high strength flexible geogrids (HSFG) as soil
reinforcement / basal reinforcement as per MORTH 3100 and IRC 113, made of
high tenacity polyester core with polyethylene coating with Minimum Long
Term Design Strength (LTDS) of more than 50% of ultimate tensile strength at
30 degree Celcius corresponding to 12 % strain .
26.18.1 Ultimate tensile strength- 100 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8962 Synthetic Geogrid having umtimate
tensile strength 100 kN/m Sqm 300.00 200.00 60000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 6000.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2069
Code Description Unit Quantity Rate Amount
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 72269.04 W
Add 1 % Water charges on "W" 722.69
TOTAL 72991.73 X
Add GST on "X" (multiplying
factor 0.1405) 10255.34
TOTAL 83247.07 Y
Add 15% CPOH on "Y" 12487.06
TOTAL 95734.13 Z
Add Cess @ 1% on "Z" 957.34
Cost for 300 Sqm 96691.47
Cost per Sqm 322.30
Say 322.30
26.18.2 Ultimate tensile strength- 150 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8963 Synthetic Geogrid having umtimate
tensile strength 150 kN/m sqm 300.00 210.00 63000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 6300.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 75569.04 W
Add 1 % Water charges on "W" 755.69
TOTAL 76324.73 X
Add GST on "X" (multiplying
factor 0.1405) 10723.62
TOTAL 87048.36 Y
Add 15% CPOH on "Y" 13057.25
TOTAL 100105.61 Z
Add Cess @ 1% on "Z" 1001.06
Cost for 300 Sqm 101106.66
Cost per Sqm 337.02
say 337.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2070
26.18.3 Ultimate tensile strength- 200 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8964 Synthetic Geogrid having umtimate
tensile strength 200 kN/m sqm 300.00 340.00 102000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 10200.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 118469.04 W
Add 1 % Water charges on "W" 1184.69
TOTAL 119653.73 X
Add GST on "X" (multiplying
factor 0.1405) 16811.35
TOTAL 136465.08 Y
Add 15% CPOH on "Y" 20469.76
TOTAL 156934.84 Z
Add Cess @ 1% on "Z" 1569.35
Cost for 300 Sqm 158504.19
Cost per Sqm 528.35
say 528.35
26.18.4 Ultimate tensile strength- 250 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8965 Synthetic Geogrid having umtimate
tensile strength 250 kN/m sqm 300.00 350.00 105000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 10500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2071
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 121769.04 W
Add 1 % Water charges on "W" 1217.69
TOTAL 122986.73 X
Add GST on "X" (multiplying
factor 0.1405) 17279.64
TOTAL 140266.37 Y
Add 15% CPOH on "Y" 21039.95
TOTAL 161306.32 Z
Add Cess @ 1% on "Z" 1613.06
Cost for 300 Sqm 162919.38
Cost per Sqm 543.06
say 543.05
26.18.5 Ultimate tensile strength- 300 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8966 Synthetic Geogrid having umtimate
tensile strength 300 kN/m sqm 300.00 360.00 108000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 10800.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 125069.04 W
Add 1 % Water charges on "W" 1250.69
TOTAL 126319.73 X
Add GST on "X" (multiplying
factor 0.1405) 17747.92
TOTAL 144067.65 Y
Add 15% CPOH on "Y" 21610.15
TOTAL 165677.80 Z
Add Cess @ 1% on "Z" 1656.78
Cost for 300 Sqm 167334.58
Cost per Sqm 557.78
say 557.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2072
26.18.6 Ultimate tensile strength- 350 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8967 Synthetic Geogrid having umtimate
tensile strength 350 kN/m sqm 300.00 370.00 111000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 11100.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 128369.04 W
Add 1 % Water charges on "W" 1283.69
TOTAL 129652.73 X
Add GST on "X" (multiplying
factor 0.1405) 18216.21
TOTAL 147868.94 Y
Add 15% CPOH on "Y" 22180.34
TOTAL 170049.28 Z
Add Cess @ 1% on "Z" 1700.49
Cost for 300 Sqm 171749.77
Cost per Sqm 572.50
say 572.50
26.18.7 Ultimate tensile strength- 400 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8968 Synthetic Geogrid having umtimate
tensile strength 400 kN/m sqm 300.00 450.00 135000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 13500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2073
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 154769.04 W
Add 1 % Water charges on "W" 1547.69
TOTAL 156316.73 X
Add GST on "X" (multiplying
factor 0.1405) 21962.50
TOTAL 178279.23 Y
Add 15% CPOH on "Y" 26741.88
TOTAL 205021.12 Z
Add Cess @ 1% on "Z" 2050.21
Cost for 300 Sqm 207071.33
Cost per Sqm 690.24
say 690.25
26.18.8 Ultimate tensile strength- 500 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8969 Synthetic Geogrid having umtimate
tensile strength 500 kN/m sqm 300.00 500.00 150000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 15000.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 171269.04 W
Add 1 % Water charges on "W" 1712.69
TOTAL 172981.73 X
Add GST on "X" (multiplying
factor 0.1405) 24303.93
TOTAL 197285.66 Y
Add 15% CPOH on "Y" 29592.85
TOTAL 226878.51 Z
Add Cess @ 1% on "Z" 2268.79
Cost for 300 Sqm 229147.30
Cost per Sqm 763.82
say 763.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2074
26.18.9 Ultimate tensile strength- 600 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8970 Synthetic Geogrid having umtimate
tensile strength 600 kN/m sqm 300.00 550.00 165000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 16500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 187769.04 W
Add 1 % Water charges on "W" 1877.69
TOTAL 189646.73 X
Add GST on "X" (multiplying
factor 0.1405) 26645.37
TOTAL 216292.10 Y
Add 15% CPOH on "Y" 32443.81
TOTAL 248735.91 Z
Add Cess @ 1% on "Z" 2487.36
Cost for 300 Sqm 251223.27
Cost per Sqm 837.41
say 837.40
26.18.10 Ultimate tensile strength- 700 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8971 Synthetic Geogrid having umtimate
tensile strength 700 kN/m sqm 300.00 650.00 195000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2075
Code Description Unit Quantity Rate Amount
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 19500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 220769.04 W
Add 1 % Water charges on "W" 2207.69
TOTAL 222976.73 X
Add GST on "X" (multiplying
factor 0.1405) 31328.23
TOTAL 254304.96 Y
Add 15% CPOH on "Y" 38145.74
TOTAL 292450.71 Z
Add Cess @ 1% on "Z" 2924.51
Cost for 300 Sqm 295375.21
Cost per Sqm 984.58
say 984.60
26.18.11 Ultimate tensile strength- 800 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8972 Synthetic Geogrid having umtimate
tensile strength 800 kN/m sqm 300.00 725.00 217500.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 21750.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2076
Code Description Unit Quantity Rate Amount
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 245519.04 W
Add 1 % Water charges on "W" 2455.19
TOTAL 247974.23 X
Add GST on "X" (multiplying
factor 0.1405) 34840.38
TOTAL 282814.61 Y
Add 15% CPOH on "Y" 42422.19
TOTAL 325236.80 Z
Add Cess @ 1% on "Z" 3252.37
Cost for 300 Sqm 328489.17
Cost per Sqm 1094.96
say 1094.95
26.18.12 Ultimate tensile strength- 900 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8973 Synthetic Geogrid having umtimate
tensile strength 900 kN/m sqm 300.00 850.00 255000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 25500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 286769.04 W
Add 1 % Water charges on "W" 2867.69
TOTAL 289636.73 X
Add GST on "X" (multiplying
factor 0.1405) 40693.96
TOTAL 330330.69 Y
Add 15% CPOH on "Y" 49549.60
TOTAL 379880.29 Z
Add Cess @ 1% on "Z" 3798.80
Cost for 300 Sqm 383679.10
Cost per Sqm 1278.93
say 1278.95
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2077
26.18.13 Ultimate tensile strength- 1000 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8974 Synthetic Geogrid having umtimate
tensile strength 1000 kN/m sqm 300.00 950.00 285000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 28500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 319769.04 W
Add 1 % Water charges on "W" 3197.69
TOTAL 322966.73 X
Add GST on "X" (multiplying
factor 0.1405) 45376.83
TOTAL 368343.56 Y
Add 15% CPOH on "Y" 55251.53
TOTAL 423595.09 Z
Add Cess @ 1% on "Z" 4235.95
Cost for 300 Sqm 427831.04
Cost per Sqm 1426.10
say 1426.10
26.18.14 Ultimate tensile strength- 1100 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8975 Synthetic Geogrid having umtimate
tensile strength 1100 kN/m sqm 300.00 1000.00 300000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wsatage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2078
Code Description Unit Quantity Rate Amount
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 30000.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 336269.04 W
Add 1 % Water charges on "W" 3362.69
TOTAL 339631.73 X
Add GST on "X" (multiplying
factor 0.1405) 47718.26
TOTAL 387349.99 Y
Add 15% CPOH on "Y" 58102.50
TOTAL 445452.49 Z
Add Cess @ 1% on "Z" 4454.52
Cost for 300 Sqm 449907.01
Cost per Sqm 1499.69
say 1499.70
26.18.15 Ultimate tensile strength- 1200 kN/m
Code Description Unit Quantity Rate Amount
MATERIAL
Details of Cost for 300 Sqm
8976 Synthetic Geogrid having umtimate
tensile strength 1200 kN/m sqm 300.00 1050.00 315000.00 P
Add 10 per cent of the cost of
reinforcing elements (synthetic
geogrids) for wastage and accessories
like tie-strips, nuts and bolts and loops/
lugs for joining reinforcing elements
with the facia pannels, overlaps and
other protective elements for synthetic
geogrids and all other activities
required to complete the item in all
respect including taxes and
transportation. 10% of "P" 31500.00
LABOUR
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2079
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar day 3.00 714.00 2142.00
TOTAL 352769.04 W
Add 1 % Water charges on "W" 3527.69
TOTAL 356296.73 X
Add GST on "X" (multiplying
factor 0.1405) 50059.69
TOTAL 406356.42 Y
Add 15% CPOH on "Y" 60953.46
TOTAL 467309.88 Z
Add Cess @ 1% on "Z" 4673.10
Cost for 300 Sqm 471982.98
Cost per Sqm 1573.28
say 1573.30
26.19 Providing at all heights, levels and locations Aluminium profile industrial
troughed sheet of Alloy 31500/31000/40800, conforming to IS 1254, IS 737, IS
2676. The sheet shall be fixed using self drilling/self tapping SS screws of
size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal,
vertical or curved surfaces i/c cutting to size and shape where required as per
specifications, detail drawings and direction of Engineer-in-Charge. The rate
shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for
fixing and approved sealent where required etc. but excluding the cost of
purlins, rafters and trusses.
26.19.1 0.71 mm thick, the profile detail width 1044/920 mm, cover width 1000/875 mm.
Code Description Unit Quantity Rate Amount
Details of cost for 216.14 sqm
Consider a shed of 20x10 metres.
(External dimensions of plinth).
Area of roof- 20.20x10.70m
= 216.14 sqm.
MATERIAL:
Sheets used = 20
Nosx10.70mx1.044m = 223.42 sqm,
Add 3% wastage = 6.70 sqm,Total =
230.12sqm
8977 Aluminium profile sheet 0.71 mm sqm 230.12 600.00 138072.00
9999 Carriage of sheets L.S. 104.00 2.12 220.48
1023 Galvanised steel J or L hooks 8 mm dia 10 Nos 47.60 120.00 5712.00
1208 Bitumen washer 100 Nos 4.76 30.00 142.80
1209 G.I. plain washer thick 100 Nos 4.76 35.00 166.60
9999 Carriage of bolts and nuts, washers etc. L.S. 8.06 2.12 17.09
9999 Sundries L.S. 39.52 2.12 83.78
LABOUR:
0130 Mistry day 2.34 784.00 1834.56
0112 Carpenter 2nd class day 9.34 714.00 6668.76
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2080
Code Description Unit Quantity Rate Amount
0114 Beldar day 9.34 645.00 6024.30
TOTAL 158942.37 W
Add 1 % Water charges on "W" 1589.42
TOTAL 160531.79 X
Add GST on "X" (multiplying
factor 0.1405) 22554.72
TOTAL 183086.51 Y
Add 15% CPOH on "Y" 27462.98
TOTAL 210549.49 Z
Add Cess @ 1% on "Z" 2105.49
Cost of 216.14 sqm 212654.98
Cost of 1 sqm 983.88
Say 983.90
26.19.2 0.91 mm thick, the profile detail width 1044/920 mm, cover width 1000/875 mm.
Code Description Unit Quantity Rate Amount
Details of cost for 216.14 sqm
Consider a shed of 20x10 metres.
(External dimensions of plinth).
Area of roof- 20.2x10.70m = 216.14 sqm.
MATERIAL:
Sheets used = 20
Nosx10.70mx1.044m = 223.42 sqm,
Add 3% wastage = 6.70 sqm, Total =
230.12sqm
8978 Aluminium profile sheet 0.91 mm sqm 230.12 785.00 180644.20
9999 Carriage of sheets L.S. 104.00 2.12 220.48
1023 Galvanised steel J or L hooks 8 mm dia 10 Nos 47.60 120.00 5712.00
1208 Bitumen washer 100 Nos 4.76 30.00 142.80
1209 G.I. plain washer thick 100 Nos 4.76 35.00 166.60
9999 Carriage of bolts and nuts, washers etc. L.S. 8.06 2.12 17.09
9999 Sundries L.S. 39.52 2.12 83.78
LABOUR:
0130 Mistry day 2.34 784.00 1834.56
0112 Carpenter 2nd class day 9.34 714.00 6668.76
0114 Beldar day 9.34 645.00 6024.30
TOTAL 201514.57 W
Add 1 % Water charges on "W" 2015.15
TOTAL 203529.72 X
Add GST on "X" (multiplying
factor 0.1405) 28595.92
TOTAL 232125.64 Y
Add 15% CPOH on "Y" 34818.85
TOTAL 266944.49 Z
Add Cess @ 1% on "Z" 2669.44
Cost of 216.14 sqm 269613.93
Cost of 1 sqm 1247.40
Say 1247.40
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2081
26.22 Providing and fixing false ceiling at all heights with integral densified calcium
silicate reinforced with fibre and natural filler false ceiling tiles of Size
595x595mm of approved texture, design and patterns as per CPWD
Specification 2019, to be laid in true horizontal level suspended on inter-locking
metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized
@ 120 grams per sqm including both sides)comprising of main-T runners
of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length
1200 mm and secondaryintermediate cross-T of size 24x32 mm of length
600mm to formgrid module of size 600 x 600 mm, suspended from ceiling
usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50
mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm
length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and
Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to
pierce into 12x50mm or even bigger size dash fastener if require, fixed with
Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000
mm to be fixed on periphey wall / partition with the help of plastic rawl plugs
at 450mm center to center and 40 mm long dry wall S.S screws. The workshall
be carried out as per specifications, drawing and as per directionsof the
Engineer-in-Charge.
26.22.1 With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
8589 Calcium Slicate tegular edged Flase
ceiling tiles 595x595 mm and 15 mm
thick sqm 105.00 685.00 71925.00
Ceiling Area = 100 sqm + Add 5%
wastage = 5 sqm. Total = 105 sqm
8590 Galavanised iron main Tee ceiling
section Size 24x38x0.33 mm (3 metre
long) including wastage @ 10% each 29.50 140.00 4130.00
8591 Galavanised iron perimeter wall Angle
Size 24x24x0.40 mm (3.00 metre long)
including wastage @ 10% each 13.50 90.00 1215.00
8592 Galavanised iron intermediate cross
T section Size 24x32x0.33 mm (1.2
metre long) including wastage @ 10% each 147.00 45.00 6615.00
8593 Glavanised iron intermediate cross
T section Size 24 x 32x 0.33 mm (0.6
metre long) each 147.00 22.00 3234.00
8588 Galavanised MS hanger rod 6 mm dia
MS fully threaded up to 1000 mm
length each 72.00 28.00 2016.00
5775 Galavinised MS L-shape level adjuster
of size 76x25x25x1.6 mm each 72.00 15.00 1080.00
5776 12x50 mm long dash fastener each 72.00 35.00 2520.00
5777 Galvanized MS Z Cleat of size 25 x
37 x 25 x 1.6 mm with precut hole on
both 25 mm flange each 72.00 12.00 864.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos. 1.00 250.00 250.00
9999 Scaffolding etc. L.S. 498.65 2.12 1057.14
9977 Carriage of materails etc. L.S. 237.48 2.12 503.46
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2082
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 310.70 2.12 658.68
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 132855.28 W
Add 1 % Water charges on "W" 1328.55
TOTAL 134183.83 X
Add GST on "X" (multiplying
factor 0.1405) 18852.83
TOTAL 153036.66 Y
Add 15% CPOH on "Y" 22955.50
TOTAL 175992.16 Z
Add Cess @ 1% on "Z" 1759.92
Cost of 100 sqm. 177752.08
Cost of 1 cum. 1777.52
Say 1777.50
26.22.2 With 15 mm thick tegular/butt edged without perforation plain/designer light
weight calcium silicate Anti-Microbial Bio-Safe coated false ceiling tiles
Confirming to JIS-Z2801 and ASTM G-21
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
5778 15 mm thick tegular/butt edged without
perforation plain/designer light weight
calcium silicate Anti-Microbial Bio-Safe
coated false ceiling tiles of size
595x595mm sqm 105.00 830.00 87150.00
Ceiling Area = 100 sqm + Add 5%
wastage = 5 sqm. Total = 105 sqm
8590 Galavanised iron main Tee ceiling
section Size 24x38x0.33 mm (3 metre
long) including wastage @ 10% each 29.50 140.00 4130.00
8591 Galavanised iron perimeter wall Angle
Size 24x24x0.40 mm (3.00 metre long)
including wastage @ 10% each 13.50 90.00 1215.00
8592 Galavanised iron intermediate cross
T section Size 24x32x0.33 mm (1.2
metre long) including wastage @ 10% each 147.00 45.00 6615.00
8593 Glavanised iron intermediate cross
T section Size 24 x 32x 0.33 mm (0.6
metre long) each 147.00 22.00 3234.00
8588 Galavanised MS hanger rod 6 mm dia
MS fully threaded up to 1000 mm length each 72.00 28.00 2016.00
5775 Galavinised MS L-shape level adjuster
of size 76x25x25x1.6 mm each 72.00 15.00 1080.00
5776 12x50 mm long dash fastener each 72.00 35.00 2520.00
5777 Galvanized MS Z Cleat of size 25 x
37 x 25 x 1.6 mm with precut hole on
both 25 mm flange each 72.00 12.00 864.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos. 1.00 250.00 250.00
9999 Scaffolding etc. L.S. 498.65 2.12 1057.14
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2083
Code Description Unit Quantity Rate Amount
9977 Carriage of materails etc. L.S. 237.48 2.12 503.46
9999 Sundries L.S. 310.70 2.12 658.68
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 148080.28 W
Add 1 % Water charges on "W" 1480.80
TOTAL 149561.08 X
Add GST on "X" (multiplying
factor 0.1405) 21013.33
TOTAL 170574.41 Y
Add 15% CPOH on "Y" 25586.16
TOTAL 196160.58 Z
Add Cess @ 1% on "Z" 1961.61
Cost of 100 sqm. 198122.18
Cost of 1 cum. 1981.22
Say 1981.20
26.23 Providing and fixing false ceiling at all heights with integral densified calcium
silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595
mm of approved texture, design and patterns having NRC (Noise Reduction
coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%
(minimum). Non combustible as per BS:476 (part-4), fire performance as per
BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043
W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-
locking metal powder coated T-Grid of hot dipped galvanised iron section of
0.40 mm thick on Silhouette profile,rotary stiched double webbed white with
6mm reveal profile (white/black),comprising of main-T runners of size
15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm
and secondary intermediate cross-T of size 15x42 mm of length 600mm to
form grid module of size 600 x 600 mm, suspended from ceiling using
galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm
long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger
rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm.
Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000
mm to be fixed on periphery wall / partition with the help of plastic rawl plugs
at 450 mm center to center and 40mm long dry wall S.S screws. The work
shall be carried out as per specifications, drawing and as per directions of the
Engineer-in-Charge.
26.23.1 With 15 mm thick integral densified micro edge light weight calcium silicate
false ceiling tiles
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
8563 15 mm thick, light weight, integral
densified micro look edged,false ceiling
tiles of size 595x595 mm. sqm 105.00 725.00 76125.00
Celling Area = 100 sqm + Add 5%
wastage = 5 sqm. Total = 105 sqm
SILHOUETTE Profile grid frame :
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2084
Code Description Unit Quantity Rate Amount
8567 Galvanized mild steel perimeter wall
angle 22x19x0.40 mm (3000 mm long) each 13.50 125.00 1687.50
including wastage @10%
8566 Powder coated steel section main-
T ceiling sections 15x42x0.40 mm
(3000 mm long) each 29.50 260.00 7670.00
including wastage @10%
8568 Powder coated Galvanised Iron
intermediate cross-T section
15x42x0.40 mm (1200 mm long) each 147.00 105.00 15435.00
including wastage @10%
8569 Powder coated Galvanized Iron
intermediate cross-T section
15x42x0.40mm (600 mm long ) each 147.00 50.00 7350.00
including wastage @10%
8588 Galavanised MS hanger rod 6 mm dia
MS fully threaded up to 1000 mm
length each 72.00 28.00 2016.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8515 Galavanised MS 8 mm outer diameter
M-6 dash fastener 50mm long each 72.00 42.00 3024.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos 1.00 250.00 250.00
9999 Scaffolding etc. L.S. 498.65 2.12 1057.14
9977 Carriage of materials etc. L.S. 237.48 2.12 503.46
9999 Sundries L.S. 310.70 2.12 658.68
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 153643.78 W
Add 1 % Water charges on "W" 1536.44
TOTAL 155180.22 X
Add GST on "X" (multiplying
factor 0.1405) 21802.82
TOTAL 176983.04 Y
Add 15% CPOH on "Y" 26547.46
TOTAL 203530.49 Z
Add Cess @ 1% on "Z" 2035.30
Cost of 100 sqm. 205565.80
Cost of 1 sqm. 2055.66
Say 2055.65
26.24 Providing and fixing in position wall panelling at all heights with integral
densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise
Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance
of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance
as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity
<0.043 W/m K as per ASTM 518:1991, comprising of a frame made from
especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section
(galvanizing @120 grams per sqm including both sides) i.e.vertical studs of
size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and
ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm
centers using 12mm dia,50mm long wedge type expanded zinc alloy dash
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2085
fastner with 10mm bolt. This same channel is then to be fixed in horiziontal
direction at 600mm center to center so as to form a grid of 600mm x 600mm.
Glasswool of 50mm thickness is then to be inserted in the slots and finally
calcium silicate non combustible panels/tiles are to be screw fixed with self
tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this
grid leaving an even groove of 1 mm between the panels. The joints between
the panels are to be duly jointed and finished using recommended jointing
calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre
)roll and two coats of primer suitable for panelling as per manufacturer's
specification as per direction of Engineer-in-Charge all complete.
26.24.1 With 15 mm thick fully perforated square/butt edge light weight calcium silicate
panels/ tiles
Code Description Unit Quantity Rate Amount
Details of cost for 6.00 x 3.65=21.90 sqm
MATERIAL
8564 15 mm thick, light weight,fully
perforated square/butt edge integral
densified,false ceiling tiles of size
595x595 mm. sqm 23.00 900.00 20700.00
Ceiling area = 21.90 sqm + 1.10 sqm
(Add 5% wastage) Total = 23.00 sqm
7367 Galvanised M.S. sheet 0.5 mm thick
pressed channel section of size 50x
32 mm metre 12.60 60.00 756.00
2 x 6.00 m=12m +0.60 (Add 5%
wastage ) = 12.60 m
7369 Galvanised M.S. sheet 0.50 mm thick
pressed stud : 48x34x36 mm metre 73.66 70.00 5156.20
11 x 3.65 m = 40.15 m + 5 x 6.00
= 30.00 m
Total= 70.15 m +3.51
( Add 5% wastage )
Total = 73.66m
7025 Self tapping pan head nickle coated
mild steel screws of size 13 x 3.2 mm 1000 Nos 0.392 480.00 188.16
7383 12 mm dia 50 mm long wedge type
expanded zinc alloy dash fastner each 19.00 7.00 133.00
7274 Glass wool 50 mm thick sqm 23.00 200.00 4600.00
21.90 +1.10 (Add 5% wastage)
= 23.00 sqm
0764 Calcium silicate base compound for
jointing calcium silicate tiles kg 4.82 26.00 125.32
22.81/103.68 x 21.9 = 4.82 kgs
7026 Fibre joint tape 50 mm wide (90 metre)
roll each roll 0.27 150.00 40.50
1.27/103.68 x 21.90 = 0.27 roll
9999 Sundries such as scaffolding, tools,
bits, etc. L.S. 130.00 2.12 275.60
9977 Carriage of materials etc. L.S. 52.00 2.12 110.24
LABOUR
0111 Carpenter 1st class day 6.57 784.00 5150.88
0.30x21.90=6.57 days
0112 Carpenter 2nd class day 2.847 714.00 2032.76
0.13x21.90=2.847 days
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2086
Code Description Unit Quantity Rate Amount
0114 Beldar day 7.665 645.00 4943.93
0.35x21.90=7.665 days
0131 Painter day 1.095 714.00 781.83
TOTAL 44994.41 W
Add 1 % Water charges on "W" 449.94
TOTAL 45444.36 X
Add GST on "X" (multiplying
factor 0.1405) 6384.93
TOTAL 51829.29 Y
Add 15% CPOH on "Y" 7774.39
TOTAL 59603.68 Z
Add Cess @ 1% on "Z" 596.04
Cost of 21.90 sqm. 60199.72
Cost of 1 sqm. 2748.85
Say 2748.85
26.25 Providing and fixing 15 mm thick false ceiling tiles at all heights with integral
densified calcium silicate reinforced with fibre and natural filler false ceiling
tiles of Size 595x595 mm of approved texture, design and patterns having
NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light
reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire
performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal
conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level on
the existing frame work consisting of T-sections and Lsections suitably fixed
according to tile size as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
MATERIAL
8589 Calcium Silicate tegular edged celling
tiles 595x595 mm and 15 mm thick sqm 10.50 685.00 7192.50
10 + 0.5 (Add wastage @5%)
= 10.5 sqm
9977 Carriage L.S. 14.95 2.12 31.69
LABOUR
0111 Carpenter 1st class day 2.50 784.00 1960.00
0114 Beldar day 2.00 645.00 1290.00
9999 Scaffolding L.S. 31.07 2.12 65.87
9999 Sundries L.S. 31.07 2.12 65.87
TOTAL 10605.93 W
Add 1 % Water charges on "W" 106.06
TOTAL 10711.99 X
Add GST on "X" (multiplying
factor 0.1405) 1505.03
TOTAL 12217.02 Y
Add 15% CPOH on "Y" 1832.55
TOTAL 14049.58 Z
Add Cess @ 1% on "Z" 140.50
Cost of 10 sqm 14190.07
Cost of 1 sqm 1419.01
Say 1419.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2087
26.26 Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced
Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design
and patterns having moisture content less than 2%, humidity resistance of
99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476
(part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal
level suspended on inter-locking metal T-Grid of hot dipped galvanised iron
section of 0.33mm thick (galvanized @ 120 grams per sqm including both
sides) comprising of main-T runners of size 15x32 mm of length 3000 mm,
cross - T of size 15x32 mm of length 1200 mm and secondary intermediate
cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x
600 mm, suspended from ceiling using galvanised mild steel items (galvanizing
@ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners,
6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level
adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size
24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition
with the help of plastic rawl plugs at 450 mm center to center and 40 mm long
dry wall wood screws. The work shall be carried out as per specifications,
drawing and as per directions of the Engineer-in-Charge.
26.26.1 With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
Celling area =100 sqm
Add wastage @ 5% = 5 sqm
Total=105.00 sqm
8581 12 mm thick micro tegular edged semi
perforated GFRG (Glass Fibre
Reinforced Gypsum) false celing tiles
of Size 595x595 mm sqm 105.00 550.00 57750.00
8555 Galvanized iron main-T ceiling sections
15x32x0.33 mm (3000 mm long) each 29.50 190.00 5605.00
Including wastage @ 10%
8591 Galvanized iron perimeter wall angle
24x24x0.40 mm (3000 mm long) each 13.50 90.00 1215.00
Including wastage @ 10%
8556 Galvanized iron intermediate cross-
T section 15x32x0.33 mm
(1200 mm long) each 147.00 78.00 11466.00
Including wastage @ 10%
8587 Galvanized iron intermediate cross-
T section 15x32x0.33 mm
(600 mm long) each 147.00 37.00 5439.00
Including wastage @ 10%
8588 Galavanised MS hanger rod 6mm dia
MS fully threaded up to 1000 mm length each 72.00 28.00 2016.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8596 Galvanised MS 8mm outer diameter
M-6 dash fastener 25mm long each 72.00 35.00 2520.00
8211 40mm SS with plastic rawl plugs 100 nos 1.00 250.00 250.00
9999 Scaffolding etc. L.S. 498.65 2.12 1057.14
9977 Carriage of materials etc. L.S. 237.48 2.12 503.46
9999 Sundries L.S. 310.70 2.12 658.68
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2088
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 126347.28 W
Add 1 % Water charges on "W" 1263.47
TOTAL 127610.75 X
Add GST on "X" (multiplying
factor 0.1405) 17929.31
TOTAL 145540.06 Y
Add 15% CPOH on "Y" 21831.01
TOTAL 167371.07 Z
Add Cess @ 1% on "Z" 1673.71
Cost of 100 sqm 169044.78
Cost of 1 sqm 1690.45
Say 1690.45
26.26.2 With fully perforated 12 mm thick micro tegular edged or 10 mm thick square
edged GRG false ceiling tiles.
Code Description Unit Quantity Rate Amount
Details of cost for 100 sqm
MATERIAL
Celling area =100 sqm
Add wastage @ 5% = 5 sqm
Total=105.00 sqm
8582 12 mm thick micro tegular edged fully
perforated GFRG (Glass Fibre
Reinforced Gypsum) false celing tiles
of Size 595x595 mm sqm 105.00 600.00 63000.00
8555 Galvanized iron main-T ceiling sections
15x32x0.33 mm (3000 mm long) each 29.50 190.00 5605.00
Including wastage @ 10%
8591 Galvanized iron perimeter wall angle
24x24x0.40 mm (3000 mm long) each 13.50 90.00 1215.00
Including wastage @ 10%
8556 Galvanized iron intermediate cross-
T section 15x32x0.33 mm
(1200 mm long) each 147.00 78.00 11466.00
Including wastage @ 10%
8587 Galvanized iron intermediate cross-
T section 15x32x0.33 mm
(600 mm long) each 147.00 37.00 5439.00
Including wastage @ 10%
8588 Galavanised MS hanger rod 6mm dia
MS fully threaded up to 1000 mm length each 72.00 28.00 2016.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8596 Galvanised MS 8mm outer diameter
M-6 dash fastener 25mm long each 72.00 35.00 2520.00
8211 40mm long SS screws with plastic
rawl plugs 100 nos 1.00 250.00 250.00
9999 Scaffolding etc. L.S. 498.65 2.12 1057.14
9977 Carriage of materials etc. L.S. 237.48 2.12 503.46
9999 Sundries L.S. 310.70 2.12 658.68
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2089
Code Description Unit Quantity Rate Amount
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 131597.28 W
Add 1 % Water charges on "W" 1315.97
TOTAL 132913.25 X
Add GST on "X" (multiplying
factor 0.1405) 18674.31
TOTAL 151587.56 Y
Add 15% CPOH on "Y" 22738.13
TOTAL 174325.70 Z
Add Cess @ 1% on "Z" 1743.26
Cost of 100 sqm 176068.96
Cost of 1 sqm 1760.69
Say 1760.70
26.27 Providing and fixing mineral fibre false ceiling tiles at all heights of size
595X595mm of approved texture, design and pattern. The tiles should have
Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal
Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6
&7)in true horizontal level suspended on interlocking T-Grid of hot dipped all
round galvanized iron section of 0.33 mm thick (galvanized @120 gsm)
comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size
15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32
mm of length 600 mm to form grid module of size 600x600 mm suspended
from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long
8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger
rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,
spaced at 1200 mm centre to centre along main ‘T’. The system should rest on
periphery walls /partitions with the help of GI perimeter wall angle of
size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with
help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S.
screws. The exposed bottom portion of all T-sections used in false ceiling
support system shall be pre-painted with polyester baked paint, for all heights.
The work shall be carried out as per specifications, drawings and as per
directions of the engineer-in-charge.
26.27.1 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55
to 0.6
Code Description Unit Quantity Rate Amount
Details of cost for 100 Sqm
MATERIAL
8552 Mineral fibre beveled tegular edged
ceiling tiles 595x595 mm, 16 mm thick sqm 105.00 835.00 87675.00
Area = 100 sqm + 5 sqm (Add for
wastage @5%) Total = 105 sqm
8555 G.I. main runner 15X32mm of 3000 mm
length, 0.33mm thick each 29.50 190.00 5605.00
including 10 % wastage
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2090
Code Description Unit Quantity Rate Amount
8556 G.I. cross Tee 15X32mm of 1200mm
length 0.33mm thick each 147.00 78.00 11466.00
including 10 % wastage
8557 G.I. cross Tee 15X32mm of 600mm
length, 0.33 mm thick each 147.00 35.00 5145.00
including 10 % wastage
8591 Galvanised Steel perimeter wall Angle
Size 24 x 24 x 0.40 mm
(3.00 metre long) each 13.50 90.00 1215.00
including 10 % wastage
8558 Galvanised Iron hanger rod 6mm dia
fully threaded upto 1000mm length each 72.00 26.00 1872.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8515 Galavanised MS 8 mm outer diameter
M-6 dash fastener 50mm long each 72.00 42.00 3024.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos 1.00 250.00 250.00
9999 Sundries i.e. scaffolding etc L.S. 187.95 2.12 398.45
9977 Carriage of material etc. L.S. 89.35 2.12 189.42
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 154706.88 W
Add 1 % Water charges on "W" 1547.07
TOTAL 156253.94 X
Add GST on "X" (multiplying
factor 0.1405) 21953.68
TOTAL 178207.62 Y
Add 15% CPOH on "Y" 26731.14
TOTAL 204938.77 Z
Add Cess @ 1% on "Z" 2049.39
Cost of 100 sqm 206988.16
Cost of 1 sqm 2069.88
Say 2069.90
26.27.2 With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)
Code Description Unit Quantity Rate Amount
Details of cost for 100 Sqm
MATERIAL
8554 Mineral fibre beveled tegular edged
ceiling tiles 595x595mm, 20 mm thick sqm 105.00 1045.00 109725.00
Area = 100 sqm + 5 sqm (Add for
wastage @5%) Total = 105 sqm
8555 G.I. main runner 15X32mm of 3000 mm
length, 0.33mm thick each 29.50 190.00 5605.00
including 10 % wastage
8556 G.I. cross Tee 15X32mm of 1200mm
length 0.33mm thick each 147.00 78.00 11466.00
including 10 % wastage
8587 G.I. cross Tee 15X32mm of 600mm
length, 0.33 mm thick each 147.00 37.00 5439.00
including 10 % wastage
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2091
Code Description Unit Quantity Rate Amount
8591 Galvanised Steel perimeter wall
Angle Size 24 x 24 x 0.40 mm
(3.00 metre long) each 13.50 90.00 1215.00
including 10 % wastage
8558 Galvanised Iron hanger rod 6mm dia
fully threaded upto 1000mm length each 72.00 26.00 1872.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8596 Galavanised MS 8 mm outer diameter
50mm long each 72.00 35.00 2520.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos 1.00 250.00 250.00
9999 Sundries i.e. scaffolding etc L.S. 187.95 2.12 398.45
9977 Carriage of material etc. L.S. 89.35 2.12 189.42
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 176546.88 W
Add 1 % Water charges on "W" 1765.47
TOTAL 178312.34 X
Add GST on "X" (multiplying
factor 0.1405) 25052.88
TOTAL 203365.23 Y
Add 15% CPOH on "Y" 30504.78
TOTAL 233870.01 Z
Add Cess @ 1% on "Z" 2338.70
Cost of 100 sqm 236208.71
Cost of 1 sqm 2362.09
Say 2362.10
26.27.3 With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tile
confirming to ISO 5 (class 100 ) specifications
Code Description Unit Quantity Rate Amount
Details of cost for 100 Sqm
MATERIAL
8553 Mineral fibre beveled tegular edged
ceiling tiles 595x595 mm, 16 mm thick
with bioblock, confirming to ISO 5
(class 100) specifications sqm 105.00 925.00 97125.00
Area = 100 sqm + 5 sqm (Add for
wastage @5%) Total = 105 sqm
8555 G.I. main runner 15X32mm of 3000 mm
length, 0.33mm thick each 29.50 190.00 5605.00
including 10 % wastage
8556 G.I. cross Tee 15X32mm of 1200mm
length 0.33mm thick each 147.00 78.00 11466.00
including 10 % wastage
8557 G.I. cross Tee 15X32mm of 600mm
length,0.33 mm thick each 147.00 35.00 5145.00
including 10 % wastage
8591 Galvanised Steel perimeter wall Angle
Size 24 x 24 x 0.40 mm
(3.00 metre long) each 13.50 90.00 1215.00
including 10 % wastage
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2092
Code Description Unit Quantity Rate Amount
8558 Galvanised Iron hanger rod 6mm dia
fully threaded upto 1000mm length each 72.00 26.00 1872.00
8619 Galavanised MS L-shape level adjuster
of size 85x25x2 mm each 72.00 15.00 1080.00
8596 Galavanised MS 8 mm outer diameter
M-6 dash fastener 50mm long each 72.00 35.00 2520.00
8211 40 mm long S.S screws with plastic
rawl plugs 100 nos 1.00 250.00 250.00
9999 Sundries i.e. scaffolding etc L.S. 187.95 2.12 398.45
9977 Carriage of material etc. L.S. 89.35 2.12 189.42
LABOUR
0111 Carpenter 1st class day 28.00 784.00 21952.00
0114 Beldar day 23.00 645.00 14835.00
TOTAL 163652.88 W
Add 1 % Water charges on "W" 1636.53
TOTAL 165289.40 X
Add GST on "X" (multiplying
factor 0.1405) 23223.16
TOTAL 188512.57 Y
Add 15% CPOH on "Y" 28276.88
TOTAL 216789.45 Z
Add Cess @ 1% on "Z" 2167.89
Cost of 100 sqm 218957.35
Cost of 1 sqm 2189.57
Say 2189.55
26.28 Chipping of unsound/weak concrete material from slabs, beams, columns etc.
with manual Chisel and/ or by standard power driven percussion type or of
approved make including tapering of all edges, making square shoulders of
cavities including cleaning the exposed concrete surface and reinforcement
with wire brushes etc. and disposal of debris for all lead and lifts all complete
as per direction of Engineer-In-Charge
26.28.1 75mm average thickness
Code Description Unit Quantity Rate Amount
Details of cost for One Sqm
75mm average thickness for beams
MACHINERY
9999 Hire charges for HILTY-TE 504
Pneumatic Chisel L.S. 5.60 2.12 11.87
LABOUR
0157 Machine Operator day 0.20 784.00 156.80
0114 Beldar day 0.10 645.00 64.50
TOTAL 233.17 W
Add 1 % Water charges on "W" 2.33
TOTAL 235.50 X
Add GST on "X" (multiplying
factor 0.1405) 33.09
TOTAL 268.59 Y
Add 15% CPOH on "Y" 40.29
TOTAL 308.88 Z
Add Cess @ 1% on "Z" 3.09
Cost of 1.0 sqm 311.97
Say 311.95
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2093
26.28.2 50mm average thickness
Code Description Unit Quantity Rate Amount
Details of cost for One Sqm
50mm average thickness for beams
MACHINERY
9999 Hire charges for HILTY-TE 504
Pneumatic Chisel L.S. 3.74 2.12 7.93
LABOUR
0157 Machine Operator day 0.134 784.00 105.06
0114 Beldar day 0.07 645.00 45.15
TOTAL 158.13 W
Add 1 % Water charges on "W" 1.58
TOTAL 159.72 X
Add GST on "X" (multiplying
factor 0.1405) 22.44
TOTAL 182.16 Y
Add 15% CPOH on "Y" 27.32
TOTAL 209.48 Z
Add Cess @ 1% on "Z" 2.09
Cost of 1.0 sqm 211.57
Say 211.55
26.28.3 25 mm average thickness
Code Description Unit Quantity Rate Amount
Details of cost for One Sqm
25mm average thickness for beams
MACHINERY
9999 Hire charges for HILTY-TE 504
Pneumatic Chisel L.S. 1.87 2.12 3.96
LABOUR
0157 Machine Operator day 0.07 784.00 54.88
0114 Beldar day 0.03 645.00 19.35
TOTAL 78.19 W
Add 1 % Water charges on "W" 0.78
TOTAL 78.98 X
Add GST on "X" (multiplying
factor 0.1405) 11.10
TOTAL 90.07 Y
Add 15% CPOH on "Y" 13.51
TOTAL 103.58 Z
Add Cess @ 1% on "Z" 1.04
Cost of 1.0 sqm 104.62
Say 104.60
26.29 Cleaning of reinforcement from rust from the reinforcing bars to give it a total
rust free steel surface by using alkaline chemical rust remover of approved
make with paint brush and removing loose particles after 24 hours of its
application with wire brush and thoroughly washing with water and allowing
it to dry, all complete as per direction of Engineer-In-Charge.
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2094
26.29.1 Bars upto 12 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 3.00 sqm (95.54
meter length of 10 mm dia bar) Bars
upto 12 mm diameter
(1 litre chemical shall cover 3.00 sqm
area of bars)
MATERIALS
7911 Chemical Rust Remover litre 1.00 245.00 245.00
LABOUR
(Application charges for 3.0 sqm)
0131 Painter day 0.162 714.00 115.67
0115 Coolie day 0.162 645.00 104.49
9999 Putty, brush, sand paper L.S. 3.162 2.12 6.70
9999 Sundries L.S. 1.98 2.12 4.20
TOTAL 476.06 W
Add 1 % Water charges on "W" 4.76
TOTAL 480.82 X
Add GST on "X" (multiplying
factor 0.1405) 67.56
TOTAL 548.37 Y
Add 15% CPOH on "Y" 82.26
TOTAL 630.63 Z
Add Cess @ 1% on "Z" 6.31
Cost of 3 sqm (95.54 m length of
10 mm dia bar) 636.94
Rate per meter length of bar 6.67
Say 6.65
26.29.2 Bars above 12 mm diameter
Code Description Unit Quantity Rate Amount
Detail of cost for 3.00 sqm (47.78
meter length of 20 mm dia bar) Bars
above 12 mm diameter
(1 litre chemical shall cover 3.00 sqm
area of bars)
MATERIALS
7911 Chemical Rust Remover litre 1.00 245.00 245.00
LABOUR
(Application charges for 3.0 sqm)
0131 Painter day 0.162 714.00 115.67
0115 Coolie day 0.162 645.00 104.49
9999 Putty, brush, sand paper L.S. 3.162 2.12 6.70
9999 Sundries L.S. 1.98 2.12 4.20
TOTAL 476.06 W
Add 1 % Water charges on "W" 4.76
TOTAL 480.82 X
Add GST on "X" (multiplying
factor 0.1405) 67.56
TOTAL 548.37 Y
Add 15% CPOH on "Y" 82.26
TOTAL 630.63 Z
Add Cess @ 1% on "Z" 6.31
Cost of 3.00 sqm (47.78m length of
20 mm dia bar) 636.94
Rate per meter length of bar 13.33
Say 13.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2095
26.30 Drilling suitable holes in reinforced or plain cement concrete with power driven
drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels,
columns and slabs to introduce steel bars for sunshades/balconies including
fixing the steel bars in position using epoxy resin anchor grout of approved
make but excluding the cost of reinforcement, all complete as per direction of
Engineer-In-Charge.
26.30.1 Upto and including 12mm dia.
Code Description Unit Quantity Rate Amount
Details of cost for 10 holes
MATERIAL
7913 Epoxy kg 0.20 585.00 117.00
Approx unit Weight of Epoxy
= 2000kg/cum or 2gm/cucm
Volume of Epoxy filled =3.14/4[(1.5)
2-(1.2)2] x 15.5cm = 9.86cucm
Weight of Epoxy for 10 holes
=10x9.86 x 2 = 197.20 gms say
200gms = 0.2 kg
MACHINERY
0088 Hire charges of Drill machine upto
30 mm dia day 0.50 160.00 80.00
LABOUR
0116 Fitter (grade 1) day 0.50 784.00 392.00
0114 Beldar day 0.50 645.00 322.50
TOTAL 911.50 W
Add 1 % Water charges on "W" 9.12
TOTAL 920.62 X
Add GST on "X" (multiplying
factor 0.1405) 129.35
TOTAL 1049.96 Y
Add 15% CPOH on "Y" 157.49
TOTAL 1207.46 Z
Add Cess @ 1% on "Z" 12.07
Rate for 10 holes 1219.53
Rate for one hole 121.95
Say 121.95
26.31 Providing, mixing and applying bonding coat of approved adhesive on chipped
portion of RCC as per specifications and direction of Engineer-In-charge
complete in all respect.
26.31.1 SBR Polymer (@10% of cement weight) modified cementitious bond coat @
2.2 kg cement per sqm of surface area mixed with specified proportion of
approved polymer
Code Description Unit Quantity Rate Amount
Details of Cost for 10.00 Sqm bonding
coat
MATERIAL
0367 Portland Cement (OPC-43 grade) tonne 0.022 5000.00 110.00
7914 SBR Polymer kg 2.20 175.00 385.00
@ 10% of cement weight= 22.00kgx
10% =2.2 kg
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2096
Code Description Unit Quantity Rate Amount
LABOUR
0155 Mason (average) day 0.27 749.00 202.23
0115 Coolie day 0.27 645.00 174.15
9999 Scaffolding and sundries (8.06/2=4.03) L.S. 4.03 2.12 8.54
TOTAL 879.92 W
Add 1 % Water charges on "W" 8.80
TOTAL 888.72 X
Add GST on "X" (multiplying
factor 0.1405) 124.87
TOTAL 1013.59 Y
Add 15% CPOH on "Y" 152.04
TOTAL 1165.63 Z
Add Cess @ 1% on "Z" 11.66
Cost for 10.00 sqm 1177.28
Rate per sqm 117.73
Say 117.75
26.31.2 Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make
Code Description Unit Quantity Rate Amount
Details of Cost for 2.20 Sqm
7913 Epoxy kg 1.00 585.00 585.00
9999 Application charge for applying bonding
coat of Epoxy L.S. 18.50 2.12 39.22
9999 Cost of brushes etc. L.S. 8.40 2.12 17.81
TOTAL 642.03 W
Add 1 % Water charges on "W" 6.42
TOTAL 648.45 X
Add GST on "X" (multiplying
factor 0.1405) 91.11
TOTAL 739.56 Y
Add 15% CPOH on "Y" 110.93
TOTAL 850.49 Z
Add Cess @ 1% on "Z" 8.50
Cost for 2.20 sqm 858.99
Rate per sqm 390.45
Say 390.45
26.32 Providing, mixing and applying SBR polymer (of approved make) modified
Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with
polymer minimum 2% by wt. of cement used) as per specifications and
directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be
done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface
has been satisfactorily evaluated by sounding / tapping with a blunt metal
instrument and/or the 75mm size cube crushing strength at the end of 28 days
to be not less than 30 N/Sqmm2).
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2097
26.32.1 12 mm average thickness.
Code Description Unit Quantity Rate Amount
Details of Cost for 10 Sqm
MATERIAL
Cement mortar 1:4 (1 cement : sand)
= 0.144 Cum
3.9 Rate as per Item No.3.9 of
SH:MORTARS cum 0.144 4355.20 627.15
7914 SBR Polymer kg 1.10 175.00 192.50
Qty of cement in mortar= 0.144x0.38
= 0.055 MT or 55kg
@ 2% of weight of cement 55kgx2%
=1.10 kg
LABOUR
0155 Mason (average) day 0.67 749.00 501.83
0115 Coolie day 0.75 645.00 483.75
0101 Bhisti day 0.92 714.00 656.88
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 2488.84 W
Add 1 % Water charges on "W" 24.89
TOTAL 2513.73 X
Add GST on "X" (multiplying
factor 0.1405) 353.18
TOTAL 2866.91 Y
Add 15% CPOH on "Y" 430.04
TOTAL 3296.95 Z
Add Cess @ 1% on "Z" 32.97
Cost for 10 sqm 3329.92
Rate per sqm 332.99
Say 333.00
26.32.2 25 mm average thickness in 2 layers.
Code Description Unit Quantity Rate Amount
Details of Cost for 10 Sqm
MATERIAL
Cement mortar 1:4 (1 cement :
4 coarse sand) =(0.144/12)x25
=0.30 Cum
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.30 4355.20 1306.56
7914 SBR Polymer kg 2.28 175.00 399.00
Cement 0.30x0.38 = 0.114 MT OR 114 kg
@ 2% of weight of cement 114kgx2%
=2.28kg
LABOUR
0155 Mason (average) day 0.94 749.00 704.06
0115 Coolie day 1.02 645.00 657.90
0101 Bhisti day 1.01 714.00 721.14
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2098
Code Description Unit Quantity Rate Amount
9999 Scaffolding and sundries L.S. 12.61 2.12 26.73
TOTAL 3815.39 W
Add 1 % Water charges on "W" 38.15
TOTAL 3853.55 X
Add GST on "X" (multiplying
factor 0.1405) 541.42
TOTAL 4394.97 Y
Add 15% CPOH on "Y" 659.25
TOTAL 5054.22 Z
Add Cess @ 1% on "Z" 50.54
Cost for 10 sqm 5104.76
Rate per sqm 510.48
Say 510.50
26.32.3 50 mm average thickness in 3 layers.
Code Description Unit Quantity Rate Amount
Details of Cost for 10 Sqm
MATERIAL
Cement mortar 1:4 (1 cement :
4 coarse sand) 0.144/12)x50= 0.60 Cum
3.9 Rate as per Item No.3.9 of
SH: MORTARS cum 0.60 4355.20 2613.12
7914 SBR Polymer kg 4.56 175.00 798.00
Cement 0.60x0.38 = 0.228 MT
OR 228 kg
@ 2% of weight of cement 228kgx2%
=4.56 kg
LABOUR
0155 Mason (average) day 1.88 749.00 1408.12
0115 Coolie day 2.04 645.00 1315.80
0101 Bhisti day 2.02 714.00 1442.28
9999 Scaffolding and sundries L.S. 25.22 2.12 53.47
TOTAL 7630.79 W
Add 1 % Water charges on "W" 76.31
TOTAL 7707.09 X
Add GST on "X" (multiplying
factor 0.1405) 1082.85
TOTAL 8789.94 Y
Add 15% CPOH on "Y" 1318.49
TOTAL 10108.43 Z
Add Cess @ 1% on "Z" 101.08
Cost for 10 sqm 10209.52
Rate per sqm 1020.95
Say 1020.95
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2099
26.33 Providing, mixing and applying SBR polymer (of approved make @ minimum
2% by wt. of cement used) modified plain/reinforced cement concrete for
structural members having minimum characteristic compressive strength
[with ordinary portland cement, coarse sand and graded stone aggregate of
10mm maximum size in proportion as per design criteria] with specified
average thickness.
Note: Rates shall be for finished surface area of concrete and shall include
the cost of labour, concrete and appropriate approved Super-Plasticiser for
rendering concrete as flowable and SBR polymer but shall exclude cost of
reinforcement, bond coat, Shear Keys, centering and shuttering, strutting,
propping etc (Payment under this item shall be made only after proper wet
curing has been done and surface has been satisfactorily evaluated by
sounding/tapping with a blunt metal instrument)
26.33.1 50mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm area (0.5cum)
M25 concrete 0.5 cum of concrete@
330 kg/cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.50 10080.15 5040.08 A
Deduction of pumping charges
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum -0.50 210.00 -105.00
7914 SBR Polymer kg 3.30 175.00 577.50
@2% of cement 165 kg = 165X2%
= 3.3 kg
TOTAL 5512.58 W
Add 1 % Water charges on "W-A" 4.73
TOTAL 5517.30 X
Add GST on "X-A" (multiplying
factor 0.1405) 67.05
TOTAL 5584.35 Y
Add 15% CPOH on "Y-A" 81.64
TOTAL 5665.99 Z
Add Cess @ 1% on "Z-A" 6.26
Cost of 10 sqm 5672.25
Cost of 1 sqm 567.23
Say 567.25
26.33.2 75mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm area (0.75cum)
M25 concrete 0.75 cum of concrete@
330 kg/cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.75 10080.15 7560.11 A
Deduction of pumping charges
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum -0.75 210.00 -157.50
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2100
Code Description Unit Quantity Rate Amount
7914 SBR Polymer kg 4.95 175.00 866.25
@2% of cement 247.50 kg
= 247.50X2% = 4.95 kg
TOTAL 8268.86 W
Add 1 % Water charges on "W-A" 7.09
TOTAL 8275.95 X
Add GST on "X-A" (multiplying
factor 0.1405) 100.58
TOTAL 8376.53 Y
Add 15% CPOH on "Y-A" 122.46
TOTAL 8498.99 Z
Add Cess @ 1% on "Z-A" 9.39
Cost of 10 sqm 8508.38
Cost of 1 sqm 850.84
Say 850.85
26.34 Providing and laying SBR Polymer modified (of approved make @ minimum
2% by wt. of cement used) plain/reinforced concrete jacket for the structural
members e.g. columns, pillars, piers, beams etc with concrete having the
specified minimum characteristic compressive strength [with ordinary portland
cement, coarse sand and graded stone aggregate of 10mm maximum size in
proportion as per design criteria] with specified average thickness all-round
existing core of RCC member.
Note: Rates shall be for finished surface area of concrete and shall include
the cost of making holes in existing RCC slab, if required, for pouring concrete
in shuttering mould of jacket and appropriate approved Super-Plasticiser for
rendering concrete as flowable self compacting and SBR polymer but shall
exclude cost of reinforcement, bond coat, Shear Keys, centering and
shuttering, strutting, propping etc (Payment under this item shall be made
only after proper wet curing has been done and surface has been satisfactorily
evaluated by sounding/tapping with a blunt metal instrument)
26.34.1 50mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm area
M25 concrete 0.5 cum of concrete with
cement content 330 kg/cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.50 10080.15 5040.08 A
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum -0.50 210.00 -105.00
7914 SBR Polymer kg 3.30 175.00 577.50
@2% of cement 165 kg = 165X2%
= 3.3 kg
TOTAL 5512.58 W
Add 1 % Water charges on "W-A" 4.73
TOTAL 5517.30 X
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2101
Code Description Unit Quantity Rate Amount
Add GST on "X-A" (multiplying
factor 0.1405) 67.05
TOTAL 5584.35 Y
Add 15% CPOH on "Y-A" 81.64
TOTAL 5665.99 Z
Add Cess @ 1% on "Z-A" 6.26
Cost of 10 sqm 5672.25
Cost of 1 sqm 567.23
Say 567.25
26.34.2 75mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm area (0.75cum)
M25 concrete 0.75 cum of concrete
with cement content 330 kg/cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.75 10080.15 7560.11 A
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum -0.75 210.00 -157.50
7914 SBR Polymer @2% of cement
247.50 kg = 247.50X2% = 4.95 kg kg 4.95 175.00 866.25
TOTAL 8268.86 W
Add 1 % Water charges on "W-A" 7.09
TOTAL 8275.95 X
Add GST on "X-A" (multiplying
factor 0.1405) 100.58
TOTAL 8376.53 Y
Add 15% CPOH on "Y-A" 122.46
TOTAL 8498.99 Z
Add Cess @ 1% on "Z-A" 9.39
Cost of 10 sqm 8508.38
Cost of 1 sqm 850.84
Say 850.85
26.34.3 100mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm area (1.00 cum)
M25 concrete 1.00 cum of concrete
with cement content 330 kg/cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 1.00 10080.15 10080.15 A
0009 Pumping charges of concrete including
Hire charges of pump, piping work &
accessories etc. cum -1.00 210.00 -210.00
7914 SBR Polymer @2% of cement
330 kg = 330X2% = 6.6 kg kg 6.60 175.00 1155.00
TOTAL 11025.15 W
Add 1 % Water charges on "W-A" 9.45
TOTAL 11034.60 X
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2102
Code Description Unit Quantity Rate Amount
Add GST on "X-A" (multiplying
factor 0.1405) 134.10
TOTAL 11168.70 Y
Add 15% CPOH on "Y-A" 163.28
TOTAL 11331.98 Z
Add Cess @ 1% on "Z-A" 12.52
Cost of 10 sqm 11344.50
Cost of 1 sqm 1134.45
Say 1134.45
26.35 Providing and injecting approved grout in proportion recommended by the
manufacturer into cracks/honey-comb area of concrete/masonry by suitable
gun/pump at required pressure including cutting of nipples after curing etc.
complete as per directions of Engineer-in-Charge.
(The payment shall be made on the basis of actual weight of approved grout
injected.)
26.35.1 Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement
used) modified Cement slurry made with non shrink compound in concrete/
RCC work
Code Description Unit Quantity Rate Amount
Detail of cost for 100 kg Acrylic
polymer mixed cement grout
MATERIAL
7927 Acrylic Polymer chemical for cracks kg 2.00 31.00 62.00
Considering 1 kg of cement grout
mixed with non shrink polymer
compound with cement @ 2% of
cement
0367 Portland Cement (OPC-43 grade) tonne 0.10 5000.00 500.00
9977 Carriage of materials L.S. 1.00 2.12 2.12
9999 Injecting charges of Stirrer mixed
polymer grout Gun, rubber, pipe and
other accessories hire charges of
plant, machinery including necessary
fuel and transportation of site L.S. 2250.00 2.12 4770.00
LABOUR
0122 Foreman day 1.00 784.00 784.00
0157 Nozzleman day 1.00 784.00 784.00
0157 Pump Operator day 1.00 784.00 784.00
TOTAL 7686.12 W
Add 1 % Water charges on "W" 76.86
TOTAL 7762.98 X
Add GST on "X" (multiplying
factor 0.1405) 1090.70
TOTAL 8853.68 Y
Add 15% CPOH on "Y" 1328.05
TOTAL 10181.73 Z
Add Cess @ 1% on "Z" 101.82
Cost of 100 kg 10283.55
Cost of 1 kg 102.84
Say 102.85
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2103
26.35.2 Stirrer mixed SBR Polymer (of approved make) modified Cement slurry made
with Shrinkage Compensating Cement in concrete/RCC work.
Code Description Unit Quantity Rate Amount
Detail of cost for 100kg of SBR
Polymer mixed cement grout
MATERIAL
7914 SBR Polymer for crack kg 2.00 175.00 350.00
0367 Portland Cement (OPC-43 grade) tonne 0.10 5000.00 500.00
9977 Carriage of materials L.S. 1.00 2.12 2.12
9999 Injecting charges of Stirrer mixed
polymer grout Gun, rubber, pipe and
other accessories hire charges of
plant, machinery including necessary
fuel and transportation of site Rs 4000/
- per day including plant shall be used
of doing approximate v Hence cost per
sqm (4000/50 = 80) L.S. 2250.00 2.12 4770.00
LABOUR
0122 Foreman day 1.00 784.00 784.00
0157 Nozzle Operator day 1.00 784.00 784.00
0157 Pump Operator day 1.00 784.00 784.00
TOTAL 7974.12 W
Add 1 % Water charges on "W" 79.74
TOTAL 8053.86 X
Add GST on "X" (multiplying
factor 0.1405) 1131.57
TOTAL 9185.43 Y
Add 15% CPOH on "Y" 1377.81
TOTAL 10563.24 Z
Add Cess @ 1% on "Z" 105.63
Cost of 100 kg 10668.88
Cost of 1 kg 106.69
Say 106.70
26.35.3 Epoxy injection grout in concrete/RCC work of approved make
Code Description Unit Quantity Rate Amount
Details of cost for10kg Epoxy grout
MATERIAL
7913 Epoxy kg 10.00 585.00 5850.00
0092 Hire charges of Plant and machinery,
it can inject - 350kg/day day 0.03 200.00 6.00
LABOUR
0114 Beldar day 0.06 645.00 38.70
0157 Nozzle Operator day 0.03 784.00 23.52
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2104
Code Description Unit Quantity Rate Amount
9999 Sundries (gloves gogles etc.) L.S. 5.00 2.12 10.60
TOTAL 5928.82 W
Add 1 % Water charges on "W" 59.29
TOTAL 5988.11 X
Add GST on "X" (multiplying
factor 0.1405) 841.33
TOTAL 6829.44 Y
Add 15% CPOH on "Y" 1024.42
TOTAL 7853.85 Z
Add Cess @ 1% on "Z" 78.54
Cost of 10 kg 7932.39
Cost of 1 kg 793.24
Say 793.25
26.36 Providing, erecting, maintaining and removing temporary protective screens
made out of specified fabric with all necessary fixing arrangement to ensure
that it remains in position for the work duration as required by the Engineer-
in-charge.
26.36.1 Wooven PVC cloth
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL
7915 Wooven PVC cloth sqm 10.00 25.00 250.00
9999 Fixing double scaffolding outside L.S. 11.00 2.12 23.32
Total Material 273.32
LABOUR
For fixing and removal after complete
of work @25% 68.33
TOTAL 341.65 W
Add 1 % Water charges on "W" 3.42
TOTAL 345.07 X
Add GST on "X" (multiplying
factor 0.1405) 48.48
TOTAL 393.55 Y
Add 15% CPOH on "Y" 59.03
TOTAL 452.58 Z
Add Cess @ 1% on "Z" 4.53
Rate for 10 sqm 457.11
Rate for 1 sqm 45.71
Say 45.70
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2105
26.37 Cleaning of exposed concrete surface of sticking material including loose
and foreign material by sand blasting with coarse sand followed by and
including cleaning with oil free air blast as per direction of Engineer in charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
Machinery
0089 Hire charges of sand blasting
equipment (14 sqm per day) day 0.70 400.00 280.00
0090 Hire charges of compressor day 0.70 500.00 350.00
Material
0982 Coarse sand (zone III) cum 1.00 1500.00 1500.00
2203 Carriage of coarse sand cum 1.00 163.93 163.93
LABOUR
0114 Beldar day 0.70 645.00 451.50
9999 Sundries L.S. 10.00 2.12 21.20
TOTAL 2766.63 W
Add 1 % Water charges on "W" 27.67
TOTAL 2794.30 X
Add GST on "X" (multiplying
factor 0.1405) 392.60
TOTAL 3186.89 Y
Add 15% CPOH on "Y" 478.03
TOTAL 3664.93 Z
Add Cess @ 1% on "Z" 36.65
Cost of 10 sqm 3701.58
Cost of 1 sqm 370.16
Say 370.15
26.38 Shotcreting R.C.C. columns, beams and slabs etc. in layers with approved
design mix concrete having the specified minimum characteristic compressive
strength [with ordinary portland cement, coarse sand and graded stone
aggregate of 10 mm maximum size in proportion as per design criteria]
including the cost of centering and shuttering at edges and corners etc. as
directed by Engineer- in-Charge
Note: Rates shall include the providing necessary ground wires etc. The
levelling gauges, if used, shall be paid for separately. Payment under this item
shall be made only after proper wet curing has been done and surface has
been satisfactorily evaluated by sounding/tapping with a blunt metal
instrument.
26.38.1 25mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
M25 concrete 0.25 cum of concrete@
330 kg/cum
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2106
Code Description Unit Quantity Rate Amount
Cubical qty of concrete for 10 sqm =
10x1.00x0.025 = 0.25 cum + Wastage
25%, = 0.25x25/100=0.0625 cum.
Total=0.3125 cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.3125 10080.15 3150.05 A
Machinary
0086 Compressor, gun, rubber pipes & other
accessories- hire charge of plant &
machinery i/c necessary fuel day 0.25 4000.00 1000.00
(approx. 40 sqm area of shotcrete
per day = 10/40 = 0.25 day)
Labour
0157 Operator (Pile/ Special machine) day 0.40 784.00 313.60
0154 Nozzel man/ gun man day 0.40 784.00 313.60
0124 Mason (brick layer) 2nd class day 0.40 714.00 285.60
0161 Helper (Technician) day 0.80 645.00 516.00
0101 Bhisti day 0.40 714.00 285.60
TOTAL 5864.45 W
Add 1 % Water charges on "W-A" 27.14
TOTAL 5891.59 X
Add GST on "X-A" (multiplying
factor 0.1405) 385.19
TOTAL 6276.78 Y
Add 15% CPOH on "Y-A" 469.01
TOTAL 6745.79 Z
Add Cess @ 1% on "Z-A" 35.96
Cost of 10 sqm 6781.74
Cost of 1 sqm 678.17
Say 678.15
26.38.2 50mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
M25 concrete 0.5 cum of concrete@
330 kg/cum
Cubical qty of concrete for 10 sqm
= 10x1.00x0.050 = 0.50 cum
Wastage 25%, = 0.50x25/100
=0.125 cum
Total=0.625 cum
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2107
Code Description Unit Quantity Rate Amount
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.625 10080.15 6300.09 A
Machinary
0086 Compressor, gun, rubber pipes & other
accessories- hire charge of plant &
machinery i/c necessary fuel day 0.40 4000.00 1600.00
(approx. 25 sqm area of shotcrete
per day = 10/25 = 0.4 day)
Labour
0157 Operator (Pile/ Special machine) day 0.40 784.00 313.60
0154 Nozzel man/ gun man day 0.40 784.00 313.60
0124 Mason (brick layer) 2nd class day 0.40 714.00 285.60
0161 Helper (Technician) day 0.80 645.00 516.00
0101 Bhisti day 0.40 714.00 285.60
TOTAL 9614.49 W
Add 1 % Water charges on "W-A" 33.14
TOTAL 9647.64 X
Add GST on "X-A" (multiplying
factor 0.1405) 470.33
TOTAL 10117.97 Y
Add 15% CPOH on "Y-A" 572.68
TOTAL 10690.65 Z
Add Cess @ 1% on "Z-A" 43.91
Cost of 10 sqm 10734.55
Cost of 1 sqm 1073.46
Say 1073.45
26.38.3 75mm thick in Grade M 25 with cement content not less than 330 kg per cum
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
M25 concrete 0.75 cum of concrete
@ 330 kg/cum
Cubical qty of concrete for 10 sqm
= 10x1.00x0.075 = 0.75 cum
Wastage 25%, = 0.75x25/100
=0.1875 cum
Total=0.9375 cum
5.33.2.1 Rate as per Item No.5.33.2.1 of
SH: Reinforced Cement Concrete cum 0.9375 10080.15 9450.14 A
Machinary
0086 Compressor, gun, rubber pipes & other
accessories- hire charge of plant &
machinery i/c necessary fuel day 0.665 4000.00 2660.00
(approx. 15 sqm area of shotcrete
per day = 10/15 = 0.665 day)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2108
Code Description Unit Quantity Rate Amount
Labour
0157 Operator (Pile/ Special machine) day 0.40 784.00 313.60
0154 Nozzel man/ gun man day 0.40 784.00 313.60
0124 Mason (brick layer) 2nd class day 0.40 714.00 285.60
0161 Helper (Technician) day 0.80 645.00 516.00
0101 Bhisti day 0.40 714.00 285.60
TOTAL 13824.54 W
Add 1 % Water charges on "W-A" 43.74
TOTAL 13868.28 X
Add GST on "X-A" (multiplying
factor 0.1405) 620.75
TOTAL 14489.03 Y
Add 15% CPOH on "Y-A" 755.83
TOTAL 15244.87 Z
Add Cess @ 1% on "Z-A" 57.95
Cost of 10 sqm 15302.82
Cost of 1 sqm 1530.28
Say 1530.30
26.39 Providing and inserting 12mm dia galvanised steel injection nipple in honey
comb area and along crack line including drilling of holes of required diametre
(20mm to 30mm) up to depth from 30mm to 80mm at required spacing and
making the hole & crack dust free by blowing compressed air, sealing the
distance between injection nipple with adhesive chemical of approved make
and allow it to cure complete as per direction of Engineer-In-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 20.00 Nos Hole
MATERIAL
7921 Adhesive chemical ml 188.00 2.00 376.00
(750 mm deep & 20 mm Dia Hole)
Volume of hole =20x(3.14/4)x2.00x
2.00x7.5=471 cub cm.
Adhesive @ 40% of 471 ml
=188.40 ml, Say 188 ml
7922 Bit of drilling machine for Hole upto
30mm dia each 1.00 500.00 500.00
(One Bit done 20 Holes only)
7923 GI injection nipple 12mm dia,
75mm long each 20.00 45.00 900.00
7924 Blowing compressed air for cleaning
holes upto 30mm dia each 20.00 10.00 200.00
LABOUR
0155 Mason (average) day 0.50 749.00 374.50
0115 Coolie day 0.50 645.00 322.50
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2109
Code Description Unit Quantity Rate Amount
0101 Bhisti day 0.50 714.00 357.00
TOTAL 3030.00 W
Add 1 % Water charges on "W" 30.30
TOTAL 3060.30 X
Add GST on "X" (multiplying
factor 0.1405) 429.97
TOTAL 3490.27 Y
Add 15% CPOH on "Y" 523.54
TOTAL 4013.81 Z
Add Cess @ 1% on "Z" 40.14
Cost of 20 Nos hole 4053.95
Cost of 1 hole 202.70
Say 202.70
26.40 Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or
other suitable size wire mesh to be fixed & firmly anchored to the concrete
surface by means of "L" shaped mild steel shear key welded with existing
reinforcement including the cost of materials, labour, tool & plants as approved
by Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 sqm
( i.e 77.50 kg.)
MATERIAL
7925 L shaped 100mm long, 10mm dia mild
steel shear key kg 1.55 80.00 124.00
key to be provided at 0.5 mtr centre to
centre in each direction
Total no. of Shear key of MS Bar in
10sqm = 25 nos
25x0.10x0.617=1.55 kg
0091 Welding charges of shear key to
existing reinforcement each 25.00 5.00 125.00
1021 Hard drawn steel wire fabric sqm 10.50 430.00 4515.00
75x25mm, weight 7.75kg/sqm
75x25 mm = 10.00 sqm + Add 5%
wastage = 0.50 sqm Total = 10.50 sqm
9977 Carriage at site L.S. 5.61 2.12 11.89
LABOUR
0103 Blacksmith 2nd class day 1.00 714.00 714.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 6134.89 W
Add 1 % Water charges on "W" 61.35
TOTAL 6196.24 X
Add GST on "X" (multiplying
factor 0.1405) 870.57
TOTAL 7066.81 Y
Add 15% CPOH on "Y" 1060.02
TOTAL 8126.84 Z
Add Cess @ 1% on "Z" 81.27
Cost of 10 sqm 8208.10
Cost of 1 sqm 820.81
Say 820.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2110
26.41 Designing, providing, installing and fixing factory finished custom designed
cold form Light Gauge Steel Framed super structure comprising of steel wall
panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel
sheet as per design requirements. The steel sheet shall be galvanized (AZ-
150gms Aluminium Zinc Alloy coated steel having minimum yield strength
300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed
steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and
IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III).
LGSFS frame shall be designed as per IS: 801 using commercially available
software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit
architecture-2011 or equivalent. Proper usage of Connection Accessories like
Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss
with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped
Angles for better structural stability. The framing section shall be cold form
C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required
length as per structural design requirement duly punched with dimple/slot at
required locations as per approved drawings. The slots will be along centre
line of webs and shall be spaced minimum 250mm away from both ends of the
member. The frame can be supplied in panelized or knock down condition in
specific dimensions and fastened with screws extending through the steel
beyond by minimum of three exposed threads. All self drilling tapping screws
for joining the members shall have a Type II coating in accordance with ASTM
B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of
length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene
rubber using self expanding carbon steel anchor bolt of dia as per approved
drawings. design subject to minimum 12mm diameter and 121mm length
conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of
100mm in RCC (RCC to be paid separately) and located not more than 300mm
from corners or termination of bottom tracks complete in all respects. The
item also includes the submission of stability reports duly examined and issued
by any NIT/IIT. The rate includes the concept design, detailed design,
fabrication of sections, transportation, installation and all required fixing
arrangement at site as described above.
Code Description Unit Quantity Rate Amount
Details of cost for 1.00 Kg
MATERIAL
8579 Cold form light gauge Steel C-section
of thickness 0.75mm i/c zink coating/
sliting etc. kg 1.05 140.00 147.00
= 1.00 + 0.05 (Add for wastage @5%)
= 1.05 kg
9977 Carriage L.S. 1.685 2.12 3.57
Deduct for
8580 Scrap value wastage of cold form
light gauge steel kg -0.05 18.00 -0.90
Labour for assembling/ fixing etc
0103 Blacksmith 2nd class day 0.01 714.00 7.14
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2111
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.03 645.00 19.35
TOTAL 176.16 W
Add 1 % Water charges on "W" 1.76
TOTAL 177.92 X
Add GST on "X" (multiplying
factor 0.1405) 25.00
TOTAL 202.92 Y
Add 15% CPOH on "Y" 30.44
TOTAL 233.36 Z
Add Cess @ 1% on "Z" 2.33
Cost for 1.00 kg 235.69
Say 235.70
26.42 Providing and fixing of external wall system on Light gauge steel frame work
with outer face cement boards as per standard sizes fixed with self- drilling /
taping screws / fasteners @ 60cm c/c of approved make. A groove of 2 mm to
3mm shall be maintained and grooves shall be sealed with silicon based
sealant. The board shall be fixed in a staggered pattern. Screws shall be of
counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length
varying from 25 to 45 mm and. Internal face 12.5 mm thick gypsum plaster
board fixed on cement board as per standard sizes fixed with self- drilling /
taping screws / fasteners @ 60cm c/c of approved make, proper taping and
jointing to be done using fiber mesh tape and epoxy and acrylic based jointing
compound for seamless finish.(cost of frame work to be paid for separately)
26.42.1 Outer face: Outer face having 6mm thick fiber cement board fixed on 9mm
thick fiber cement board, Type A, as per IS:14862:2000 (high pressure steam
cured) Inner Face :- 12.5 mm thick gypsum plaster board conforming to IS
2095:2011 fixed on 8 mm thick fibre cement board confirming to IS:14862:2000
of type B (High pressure steam cured)
Code Description Unit Quantity Rate Amount
Details of Cost for 10.00 Sqm
MATERAILS
Outer face:
0238 6mm thick Type A fiber cement board
1x10 =10 Sqm + 1.00 (Add for wastage
@ 10%) Total = 11.00 Sqm Sqm 11.00 470.00 5170.00
2636 GI Screws of Gauge 10, length 45 mm
for fixing cement fibre board to C section. each 40.00 3.10 124.00
0240 9 mm thick Type A fiber cement board
1x10=10 sqm +1 sqm (Add for
wastage @10%) Total = 11.00 sqm Sqm 11.00 625.00 6875.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement fibre board to C
section Tapping and finishing Cement
board joints each 40.00 3.15 126.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2112
Code Description Unit Quantity Rate Amount
Sub A/R 1 Filling the Grove of 2 mm to 3 mm
between 6 mm and 9 mm thick
cement bonded particle boards. Sqm 10.00 92.85 928.50
Inner face :
0239 8 mm thick Type B fiber cement
board 1x10 = 10 sqm +1.00 (Add for
wastage
@ 10%) Total = 11.00 Sqm. Sqm 11.00 300.00 3300.00
2636 GI screw of gauge 10, length 45 mm
for fixing cement bonded particle
board to C section each 40.00 3.10 124.00
7009 12.5 mm thick tapered edge gypsum
plain board 1x10 =10 sqm +1.00
(Add for wastage @10%) Total
= 11.00 sqm. Sqm 11.00 140.00 1540.00
2635 GI Screws of Gauge 10, length
25 mm for Gypsum board to C section. each 40.00 3.15 126.00
Sub A/R 2 Filling the grove of 2 mm to 3 mm
between 8 mm thick heavy duty
cement fibre board and 12.5 mm thick
gypsum plastic board. Sqm 10.00 243.75 2437.50
LABOUR
For cutting and fixing of cement and
gypsum board
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0114 Beldar day 6.00 645.00 3870.00
TOTAL 26049.00 W
Add 1 % Water charges on "W" 260.49
TOTAL 26309.49 X
Add GST on "X" (multiplying
factor 0.1405) 3696.48
TOTAL 30005.97 Y
Add 15% CPOH on "Y" 4500.90
TOTAL 34506.87 Z
Add Cess @ 1% on "Z" 345.07
Cost of 10 sqm 34851.94
Cost of 1 sqm 3485.19
Say 3485.20
26.42.2 Outer face: Outer face having 8 mm thick cement bonded particle Board fixed
on 10 mm thick cement bonded particle board. (Termite, Fire and Moisture
Resistance) as per IS 14276:1995. Inner face:-12.5 mm thick gypsum plaster
board conforming to IS 2095:2011 fixed on 8 mm thick cement bonded particle
board (Termite, fire and moisture resistance) confirming to IS:14276:1995)
Code Description Unit Quantity Rate Amount
Details of Cost for 10.00 Sqm
MATERAILS
Outer face :
0243 8mm thick Cement bonded particle
board 1x10 =10 Sqm + 1.00 (Add for
wastage @ 10%) Total = 11.00 Sqm Sqm 11.00 215.00 2365.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2113
Code Description Unit Quantity Rate Amount
2636 GI Screws of Gauge 10, length
45 mm for fixing cement bonded
particle board to C section. each 40.00 3.10 124.00
0249 10 mm thick Cement Bonded particle
board 1x10=10 sqm +1 sqm (Add for
wastage @10%) Total = 11.00 sqm Sqm 11.00 475.00 5225.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement bonded particle
board to C section Tapping and
finishing Cement board joints each 40.00 3.15 126.00
Sub A/R 1 Filling the Groove of 2mm to 3 mm
between 8 mm and 10 mm thick
cement bonded particle boards. Sqm 10.00 92.85 928.50
Inner face :
0243 8 mm thick cement bonded particle
board 1x10 = 10 sqm +1.00 (Add for
wastage @ 10%) Total = 11.00 Sqm. Sqm 11.00 215.00 2365.00
2636 GI screw of gauge 10, length 45 mm
for fixing cement bonded particle
board to C section. each 40.00 3.10 124.00
7009 12.5 mm thick tapered edge gypsum
plain board 1x10 =10 sqm +1.00
(Add for wastage @10%)
Total = 11.00 sqm. Sqm 11.00 140.00 1540.00
2635 GI Screws of Gauge 10, length
25 mm for Gypsum board to C section. each 40.00 3.15 126.00
Sub A/R 2 Filling the grove of 2 mm to 3 mm
between 8 mm thick cement bonded
particle board and 12.5 mm thick
gypsum plastic board. Sqm 10.00 243.75 2437.50
LABOUR
For cutting and fixing of cement
and gypsum board
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0114 Beldar day 6.00 645.00 3870.00
TOTAL 20659.00 W
Add 1 % Water charges on "W" 206.59
TOTAL 20865.59 X
Add GST on "X" (multiplying
factor 0.1405) 2931.62
TOTAL 23797.21 Y
Add 15% CPOH on "Y" 3569.58
TOTAL 27366.79 Z
Add Cess @ 1% on "Z" 273.67
Cost of 10 sqm 27640.45
Cost of 1 sqm 2764.05
Say 2764.05
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2114
Sub A/R-1 Filling the groove (i.e. 2-3mm gap between boards),taping and jointing of
the first layer 6mm and 9mm thick fiber cement boards with epoxy based
sealing compound or with silicon sealant. Second layer is fixed over it in a
staggered pattern.
Code Description Unit Quantity Rate Amount
Details of cost for 1 Sqm
MATERIAL
1248 Epoxy based sealing Compound kg 0.14 535.00 74.90
LABOUR
0112 Carpenter 2nd class day 0.0132 714.00 9.42
0114 Beldar day 0.0132 645.00 8.51
Cost of 1 sqm 92.84
Say 92.85
Sub A/R-2 Fill the groove (i.e. 2-3mm gap between boards),taping and jointing 8mm
thick fiber cement board and 12.5mm thick gypsum plaster boards with
epoxy based sealing compound, Acrylic based sealing compound, Non
woven reinforcement Tape as per direction of Engineer in charge.(Use a
flexible knife so that no air bubble is entrapped. Allow 1-2 hours gap. Once
hard tacky or set, apply a coat of Acrylic based sealing compound paste to
flash fill the beveled area. After 2-4 hours go on to repeat a skin coat with
Acrylic based sealing compound to securely embed the 40mm width (non
woven reinforcement Tape. Use only flexible steel knife, such as provided
with packs, to avoid air entrapment within compound. After overnight drying
shrinkage apply a coat of acrylic based sealing compound to compensate
shrinkage. Finally cover the bevel portion with any suitable overall skin coat
with a desired full surface-leveler material).
Code Description Unit Quantity Rate Amount
Details of cost for 1 Sqm
MATERIAL
1248 Epoxy based sealing Compound kg 0.14 535.00 74.90
1249 Acrylic based sealing compound kg 0.26 500.00 130.00
1250 Non woven reinforcement Tape metre 25.00 0.14 3.50
LABOUR
0112 Carpenter 2nd class day 0.026 714.00 18.56
0114 Beldar day 0.026 645.00 16.77
Cost of 1 sqm 243.73
Say 243.75
26.43 Providing and fixing internal wall panels on Light gauge steel frame work with
12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on cement
board as per standard sizes fixed with self-drilling / taping screws / fasteners
@ 60cm c/c of approved make, Screws shall be of counter sunk rib head of
1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm.
Proper taping and jointing to be done using fiber mesh tape and epoxy and
acrylic based jointing compound for seamless finish.(cost of frame work to be
paid for separately
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2115
26.43.1 Cement Fiber Board 8 mm thick as per IS 14862:2000 of type B (High pressure
Steam Cured)
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
Material
0239 8 mm thick Type B fiber cement
board 2x10=20 sqm + 2.00
(Add for wastage @10 %)
= 22.00 sqm Sqm 22.00 300.00 6600.00
2635 GI screws of gauge 10, length
25 mm for fixing cement fiber board
to C section Tapping and finishing
Cement board joints. each 80.00 3.15 252.00
0241 12.5 mm thick Gypsum plaster
board 2x10 = 20 sqm + 2.00
(Add for wastage @ 10%)
= 22.00 sqm Sqm 22.00 170.00 3740.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement fiber board to
C section Tapping and finishing
Cement board joints. each 80.00 3.15 252.00
Sub A/R 2 Filling the grove of 2 mm to 3 mm
between 8 mm thick cement bonded
particle board and 12.5 mm thick
gypsum plastic board. Sqm 10.00 243.75 2437.50
LABOUR (For cutting & fixing cement
board and Gypsum board)
0112 Carpenter 2nd class day 1.11 714.00 792.54
0114 Beldar day 3.33 645.00 2147.85
TOTAL 16221.89 W
Add 1 % Water charges on "W" 162.22
TOTAL 16384.11 X
Add GST on "X" (multiplying
factor 0.1405) 2301.97
TOTAL 18686.08 Y
Add 15% CPOH on "Y" 2802.91
TOTAL 21488.99 Z
Add Cess @ 1% on "Z" 214.89
Cost of 10 sqm 21703.88
Cost of 1 sqm 2170.39
Say 2170.40
26.43.2 Cement Bonded particle board 8 mm (Termite, Fire & Moisture Resistance), as
per IS:14276 : 1995
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
Material
0243 8 mm thick cement bonded particle
board 2x10=20 sqm + 2.00
(Add for wastage @10 %)
= 22.00 sqm Sqm 22.00 215.00 4730.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2116
Code Description Unit Quantity Rate Amount
2635 GI screws of gauge 10, length 25 mm
for fixing cement bonded particle
board to C section Tapping and
finishing Cement board joints. each 80.00 3.15 252.00
0241 12.5 mm thick Gypsum plaster
board 2x10 = 20 sqm + 2.00
(Add for wastage @ 10%)
= 22.00 sqm Sqm 22.00 170.00 3740.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement bonded particle
board to C section Tapping and
finishing Cement board joints. each 80.00 3.15 252.00
Sub A/R 2 Filling the grove of 2 mm to 3 mm
between 8 mm thick cement bonded
particle board and 12.5 mm thick
gypsum plastic board. Sqm 10.00 243.75 2437.50
LABOUR (For cutting & fixing cement
board and Gypsum board)
0112 Carpenter 2nd class day 1.11 714.00 792.54
0114 Beldar day 3.33 645.00 2147.85
TOTAL 14351.89 W
Add 1 % Water charges on "W" 143.52
TOTAL 14495.41 X
Add GST on "X" (multiplying
factor 0.1405) 2036.60
TOTAL 16532.01 Y
Add 15% CPOH on "Y" 2479.80
TOTAL 19011.82 Z
Add Cess @ 1% on "Z" 190.12
Cost of 10 sqm 19201.93
Cost of 1 sqm 1920.19
Say 1920.20
26.44 Providing and fixing in all exterior face panels breathable vapour barrier
underneath the cement fiber board as per National Building Code 2009 complete
as per direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10.00 Sqm
MATERIAL
2637 Vapour barrier sqm 11.00 180.00 1980.00
10.00 sqm + 1.00 sqm (Add for
wastage @10%) = 11.00 sqm
LABOUR
For fixing fixing 45 sqm vapour barrier
0112 Carpenter 2nd class day 0.22 714.00 157.08
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2117
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.22 645.00 141.90
TOTAL 2046.44 W
Add 1 % Water charges on "W" 20.46
TOTAL 2066.90 X
Add GST on "X" (multiplying
factor 0.1405) 290.40
TOTAL 2357.30 Y
Add 15% CPOH on "Y" 353.60
TOTAL 2710.90 Z
Add Cess @ 1% on "Z" 27.11
Cost of 10 sqm 2738.01
Cost of 1.00 sqm 273.80
Say 273.80
26.45 Supplying and installation of moisture resistant/fire resistant cement board as
per standard sizes fixed with self-drilling / taping screws. Screws shall be of
counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length
varying from 25 to 45 mm.
26.45.1 Cement Fiber Board 6 mm thick as per IS 14862:2000 of type B (High pressure
Steam Cured)
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
Material
0238 6 mm thick fibre cement board
10 sqm +1 sqm (Add for wastage
@10%)=11.00 sqm Sqm 11.00 470.00 5170.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement fibre board to
C section Tapping and finishing
Cement board joints each 40.00 3.15 126.00
Sub A/R 1 Filling the Grove of 2 mm to 3 mm
between 6 mm and 10 mm thick
cement bonded particle boards. Sqm 10.00 92.85 928.50
LABOUR
For cutting and fixing of Cement &
gypsum board
0112 Carpenter 2nd class day 1.11 714.00 792.54
0114 Beldar day 3.33 645.00 2147.85
TOTAL 9164.89 W
Add 1 % Water charges on "W" 91.65
TOTAL 9256.54 X
Add GST on "X" (multiplying
factor 0.1405) 1300.54
TOTAL 10557.08 Y
Add 15% CPOH on "Y" 1583.56
TOTAL 12140.65 Z
Add Cess @ 1% on "Z" 121.41
Cost of 10 sqm 12262.05
Cost of 1 sqm 1226.21
Say 1226.20
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2118
26.45.2 Cement Bonded particle board 8 mm thick (Termite, Fire & Moisture Resistance),
as per IS:14276 : 1995
Code Description Unit Quantity Rate Amount
Details of cost for 10 Sqm
Material
0243 8 mm thick cement bonded particle
board 10 sqm +1 sqm (Add for
wastage @10%)=11.00 sqm Sqm 11.00 215.00 2365.00
2635 GI screws of gauge 10, length 25 mm
for fixing cement bonded particle
board to C section Tapping and
finishing Cement board joints each 40.00 3.15 126.00
Sub A/R 1 Filling the Grove of 2 mm to 3 mm
between 6 mm and 10 mm thick
cement bonded particle boards. Sqm 10.00 92.85 928.50
LABOUR
For cutting and fixing of Cement &
gypsum board
0112 Carpenter 2nd class day 1.11 714.00 792.54
0114 Beldar day 3.33 645.00 2147.85
TOTAL 6359.89 W
Add 1 % Water charges on "W" 63.60
TOTAL 6423.49 X
Add GST on "X" (multiplying
factor 0.1405) 902.50
TOTAL 7325.99 Y
Add 15% CPOH on "Y" 1098.90
TOTAL 8424.89 Z
Add Cess @ 1% on "Z" 84.25
Cost of 10 sqm 8509.14
Cost of 1 sqm 850.91
Say 850.90
26.46 Providing and fixing in position, 200 mm thick factory made Expanded
Polystyrene Core (EPS Core) wall panels consisting of EPS core sandwiched
between two Engineered sheets of welded wire fabric mesh duly finished with
shortcrete materials on outer faces. The fabric mesh shall be made of 3 mm
dia G.I. wire mesh with 50 mm pitch in both the directions and on both faces of
the wall, kept at 120-135 mm gap and connected by the zig zag G.I. wire of 3
mm dia at alternate row by welding (at an angle ranging from 50-70 degree) .
The EPS core shall consist of 100 mm thick EPS of density not less than 20 kg/
per cum. Both the outer faces of the panel shall be finished by applying the
layer of 50 mm thick cement mortar 1:3 {1 cement: 3 coarse sand (not having
more than 40% stone chips of size upto 6 mm)} À with the help of shotcreting/
guniting equipment etc at a pressure not less than 1 bar (100Kn/m2) and both
surfaces finished with trowel. Fixing operations of wall panels shall be
completed in all respect as per drawings and specifications and under the
overall direction of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1.20x3.00m
= 3.60 sqm
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2119
Code Description Unit Quantity Rate Amount
MATERIAL
8013 Factory made EPS Core wallpanel /
roof panel sandwiched between two
Engineered welded wire fabric mesh of
3 mm dia G.I. wire mesh,with 50 mm
pitch in both the directions, kept at
120-135 mm gap and interconnected
by the zig zag G.I. wire of 3 mm dia at
alternate row by welding. sqm 3.78 1650.00 6237.00
3.60 sqm + 0.18 sqm (Add for
wastage @5%)Total = 3.78 sqm
9999 Add for L-shape,U-shape & straight
lap mesh L.S. 208.00 2.12 440.96
Cement mortar 1:3 (1cement:
3 coarse sand)
2x1.20x3.00x0.05= 0.36 cum
3.8 Rate as per Item No.3.8 of SH: Mortar cum 0.36 5024.15 1808.69
10 mm TMT bars (2 nos.75 mm long)
Aluminium C-channels (100mmx
150mm long)
9999 For fixing wall with foundation L.S. 312.15 2.12 661.76
LABOUR
9999 For carrying out shotcreting, shoring,
leveling, and finishing the surface
with trowel. L.S. 707.50 2.12 1499.90
TOTAL 10648.31 W
Add 1 % Water charges on "W" 106.48
TOTAL 10754.80 X
Add GST on "X" (multiplying
factor 0.1405) 1511.05
TOTAL 12265.84 Y
Add 15% CPOH on "Y" 1839.88
TOTAL 14105.72 Z
Add Cess @ 1% on "Z" 141.06
Cost of 3.60 sqm 14246.78
Cost of 1 sqm 3957.44
Say 3957.45
26.47 Providing and fixing in position, 230mm thick factory made Expanded
Polystyrene Core (EPS Core) roof/floor panels made of 3 mm dia G.I. wire mesh
with 50 mm pitch in both the directions and on both faces of panel, kept at 120-
135 mm gap and connected by the zig zag G.I. wire of 3 mm dia at alternate row
by welding (at an angle ranging from 50-70 degree). The EPS core shall consist
of 100 mm thick EPS of density not less than 20kg/ per cum. The bottom side of
the panel shall be finished by applying a layer of 60-65 mm thick cement mortar
1: 3 {1 cement: 3 coarse sand (not having more than 40% stone chips of size
upto 6 mm)} À with the help of shotcreting equipment etc at a pressure of not
less than 1 bar (100Kn/m2) and surface finished with trowel. The top face of the
panel shall be provided and finished by applying 70-75 mm thick layer of cement
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2120
concrete 1:1.5: 3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20
mm nominal size). Fixing operations of roof/floor panels shall be completed in
all respect as per drawings and specifications and under the overall direction
of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1.20x3.00m
= 3.60 sqm
MATERIAL
8013 Factory made EPS Core wallpanel /
roof panel sandwiched between two
Engineered welded wire fabric mesh of
3 mm dia G.I. wire mesh,with 50 mm
pitch in both the directions, kept at
120-135 mm gap and interconnected
by the zig zag G.I. wire of 3 mm dia at
alternate row by welding. sqm 3.78 sqm 3.78 1650.00 6237.00
3.60 sqm + 0.18 sqm (Add for wastage
@5%)Total = 3.78 sqm
Cement mortar 1:3 (1cement:
3 coarse sand)
60mm thick on the bottom of roof slab
=1x1.2x3.00x0.060= 0.216cum
3.8 Rate as per Item No.3.8 of SH: Mortar cum 0.216 5024.15 1085.22
Cement concrete 1:1.5:3
70mm thick on the top of roof slab
=1x1.20x3.00x0.07= 0.252 cum
5.3 Rate as per Item No.5.3 of
SH: Reinforced Cement Concrete cum 0.252 10719.30 2701.26 A
9999 Add for L-shape, U-shape & straight
lap mesh L.S. 202.32 2.12 428.92
LABOUR
9999 For providing concreting, shotcreting,
shoring, leveling, plastering and
finishing the surface with trowel. L.S. 832.36 2.12 1764.60
TOTAL 12217.00 W
Add 1 % Water charges on "W-A" 95.16
TOTAL 12312.16 X
Add GST on "X-A" (multiplying
factor 0.1405) 1350.33
TOTAL 13662.49 Y
Add 15% CPOH on "Y-A" 1644.18
TOTAL 15306.67 Z
Add Cess @ 1% on "Z-A" 126.05
Cost of 3.60 sqm 15432.73
Cost of 1 sqm 4286.87
Say 4286.85
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2121
26.48 Providing and fixing of customized Aluminium form work for monolithic
construction on RCC members with repetitive usage made up of aluninium
sheets/plates of minimum 4mm thickness and grade 6061 (Type-6). The formwork
comprises of (a) wall panel, roccker, kickerand internal soffit corner, external
soffit corner, external corner, internal corner etc., (b) beam components i.e,
beam side panel prop head for soffit beam, beams soffit panel, beam soffit bulk
head and (c) deck components i.e. deck panel, deck prop, prop length, deck
mid, soffit length, deck beam bar. The panels are held in position by a simple
pin and wedge system that passes thorugh holes in the out side rib of each
panel. The tolerance of finished panel shall not be less than (-1 mm) and shall
conform to IS 14987-1999. Pins and wedges to be made of high grade hot dipped
galvansied mild steel. This form work also comprises of M.S. angle iron, "Z"
shaped brackets braced diagonally at 0.90 to 1.00 mtr. centre to centre on
extrenal wall face just the level below on which to lay M.S. square tube panels
(Challis) and guard railing supports to form working platform and 40 mm dia
G.I. telescopic adjustable props to support deck formwork and beam soffit
panels including de-shuttering the formwork from odd/even level to be shifted/
lifted to next alterante odd/even level before which the points and shuttering
surface to be thoroughly cleaned, pins greasing and shuttering surface oiling
propoerly before fixing all complete including sealing of gap between kicker
plates of wall panel and floors (if any) as per design of formwork as provided
by shuttering supplier and as per direction of the Engineer-in-charge including
filling and finishing the holes of varied sizes and shapes (left by keys/pins of
aluminium form work shuttering while de-shuttering) with GP-2 cementeous
polymer compound mixed with water in ratio prescribed by manufacturer to
form consistent workable dough for pushing it in the holes upto full depth of
wall using appropriate tools and finishing smooth all complete as per directions
of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 100 sqm (Assuming
100 repetitions)
MATERIAL
Aluminium forwork & MS working
platform 100 sqm @ 849431.55 =
849431.55 (Total material cost
modified as 'D' below)
Therefore cost for using once
849431.55/100 = 8494.32 8494.32
Deduct solvage value of aluminium for
work and working platform with 100
repetitions @30% of bare material cost
i.e, Rs.699400.00 (marked as ' A '
below ) = 699400 /100 @ 30%
= (-) 2098.20 -2098.20
5772 Grease to be applied to pins for
100 sqm @ 5pins/sqm. using 25gm
grease /pin = 100x5x25 gm = 12.50 Kg Kg 12.50 180.00 2250.00
9999 Add replacement of lost/ damaged
accessories L.S. 98.85 2.12 209.56
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2122
Code Description Unit Quantity Rate Amount
5773 Shuttering oil for panels @ 20sqm /
ltr = 100/20 = 5.00 ltr litre 5.00 90.00 450.00
9999 Add sundries for gaps filling with
sealants etc. and T& P including pully,
ropes and misc. tools L.S. 400.00 2.12 848.00
9999 Add for PVC sleeve and plastic cover
for wall tiles L.S. 500.00 2.12 1060.00
LABOUR
0116 Fitter day 5.00 784.00 3920.00
0117 Assistant Fitter day 5.00 714.00 3570.00
0155 Mason (Average) day 2.00 749.00 1498.00
0114 Beldar day 10.00 645.00 6450.00
TOTAL 26651.68
Sub A/R-2 Add for filling and fishing the holes of
aluminium form work with GP-2 each 450.00 16.65 7492.50
TOTAL 34144.18 W
Add 1 % Water charges on "W" 341.44
TOTAL 34485.62 X
Add GST on "X" (multiplying
factor 0.1405) 4845.23
TOTAL 39330.85 Y
Add 15% CPOH on "Y" 5899.63
TOTAL 45230.48 Z
Add Cess @ 1% on "Z" 452.30
Cost of 10.00 sqm 45682.78
Cost of 1.00 sqm 456.83
Say 456.85
Sub A/R - 1
Code Description Unit Quantity Rate Amount
Material cost
Part-1 : Aluminium formwork
4mm thick sheet of aluminium alloy
grade 6061 (type-6) for the contact
face area of 100 sqm
the sheet/plate requirement including
framing flanges and specials = 100 +
120 = 220 sqm
220 sqm @ 10.72 kg/sqm = 2358.40 Kg
Add 5% extra waste = 117.92 Kg
Total = 2358.40 + 117.82 = 2476.32 Kg
5780 4mm thick sheet of aluminium alloy
grade 6061 (type-6) for aluminuum
formwork Kg 2476.32 250.00 619080.00( E)
Aluminium formwork weight without
wastage = 2358.40 Kg
5781 Fabrication cost for formwork panels
and special including computerised
designing for fabrication and mock
testing before transportation to site of
work. Kg 2358.40 35.00 82544.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2123
Code Description Unit Quantity Rate Amount
Accossories like pins, wedges and
wall ties @ 5% of ( E ) 30954.00
Add cost towards maintenance and
time to time repalcement of damaged
members @5% ( E ) 30954.00
5782 Packaging and carting of aluminium
sheet/plate to the site of work Tonne 2.36 5000.00 11800.00
Total 775332.00
Say 775332.00(B)
Part-2: M S working platform on
external face (required while fixing &
removing )
10.2 M.S angle iron bracket of size
50x50x6 mm Kg 270.00 58.44 15779.47
10x6.00 mtr @ 4.50 Kg/mtrs = 270 Kg
(Rate as per item no 10.2
SH:10 Steel Work excluding WC,
GST, CPOH & Cess )
10.16.1 M.S. Square tube panel of tubes
25x25mm, 1.8mm thick Kg 256.25 115.79 29670.06
7x2x11.45 = 160mtr + 45 mtr
(railing guards) = 205 mtr @
1.25 Kg/mtr = 256.25 Kg (Rate as
per item no.10.16.1 SH: Steel Work
excluding WC, GST, CPOH & Cess )
Applying red oxide primer on steel
work (approx. 15 sqm)
7343 40 mm dia G.I. telescopic adjsutabe
props 2-3.5 mtr each 30.00 955.00 28650.00
Bare cost of material 74099.53
Say 74099.55(C)
5783 M S working platform for aluminium
formwork Kg 270.00 46.00 12420.00
4009 M S tube panel Kg 256.25 60.00 15375.00
7343 Telescopic props = 30x2.75x2
= 165 mtr. One prop length =
3m. Total number of prop = 165/3
= 55 Nos. each 55.00 955.00 52525.00
Total 80320.00
Aluminium formworkmatrial cost
(marked as ' E ' = 619080 619080.00
Grand total 699400.00(A)
Total material cost ( B ) + ( C ) 849431.55
Say 849431.55(D)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2124
Sub A/R - 2 Filling and finishing the holes of varies sizes and shades (left by keys/pins
of aluminium formwork shuttering while de-shuttering ) with GP-2
cementeous polymer compound mixed with water in ratio prescribed by
manufacturer to form consistent workable dough for pushing it in the holes
upto full depth of wall using appropriate tools and finishing smooth all
complete as per directions of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 0.01 cum
(Assuming 100 to 120 nos holes of
0.0001cum to 0.00008 cum size can
be filled with 25 kg (i/c wastage) of GP-
2 compound)
Material
5774 GP-2 Cementeous compound
(100 holes of 0.0001 cum size
= 0.01 cum) Kg 25.00 20.00 500.00
Labour
0124 Mason 2nd class day 0.90 714.00 642.60
0114 Beldar day 0.90 645.00 580.50
9999 Sundries for T&P and scaffolding etc. L.S. 50.00 2.12 106.00
Total 1829.10
Cost per each (1588.30/110) 16.63
say 16.65
26.49 Providing and fixing in position factory made EPS cement sandwich wall/roof/
floor light weight solid core panels made of core material of EPS granule balls/
beads (conforming to IS 4671:1984 and shall have density not less than 15kg
per cum) adhesive, cement, sand, flyash and other bonding material in mortar
state processed to form in a preset mould. The outer face on both sides of the
panels will be non asbestos fiber cement board confirming to IS 14862:2000 or
Calcium silicate board confirming to EN 14306:2009 of 5mm thick each. Panel
shall be laid on 6mm thick cement mortar (1 cement: 2 fine sand) mixed with
chemical adhesive of 0.5kg per 50kg of cement or shall be preferably fixed into
'C' channel made of 1.2mm thick MS plate screwed/fastenened to the slab/
column/beam etc. The panel shall fixed vertically with tongue and groove joint
and horizontally locked with steel bar between each other and floors and filled
with cement mortar and adhesive. Panels should be used as floor & roofing
with additional structural support, steel or RCC depending upon the design.
All the operation shall be completed in all respect as per drawings,
Manufacturers specifications and under the overall direction of Engineer-in-
Charge (Cost of all the material is included except "C channel" which will be
paid seperately).
26.49.1 Non load bearing panels 50mm thick of required size
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2125
Code Description Unit Quantity Rate Amount
7996 Factory made EPS light weight
composite sandwitched wall/roof panel
(50mm thick) having core material of
EPS granule balls/beads (conforming
to IS 4671:1984 and shall have density
not less than 15kg per cum). The outer
face on both sides of the panels will be
non asbestos fiber cement board
confirming to IS 14862:2000 or
Calcium silicate board confirming to
EN 14306:2009 of 5mm thick each sqm 10.50 735.25 7720.13
9999 Sundries, wooden wedge for levelling,
cement mortar, Chemical adhesive &
dowel bar (6mm dia) L.S. 37.00 2.12 78.44
LABOUR
For fixing, aligning, locking the panels
0123 Mason Grade -1 day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 8835.57 W
Add 1 % Water charges on "W" 88.36
TOTAL 8923.92 X
Add GST on "X" (multiplying
factor 0.1405) 1253.81
TOTAL 10177.73 Y
Add 15% CPOH on "Y" 1526.66
TOTAL 11704.39 Z
Add Cess @ 1% on "Z" 117.04
Cost of 10 sqm 11821.44
Cost of 1sqm 1182.14
Say 1182.15
26.49.2 Non load bearing panels 60mm thick of required size
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
7997 Factory made EPS light weight
composite sandwitched wall/roof panel
(60mm thick) having core material of
EPS granule balls/beads (conforming
to IS 4671:1984 and shall have density
not less than 15kg per cum). The outer
face on both sides of the panels will be
non asbestos fiber cement board
confirming to IS 14862:2000 or
Calcium silicate board confirming to
EN 14306:2009 of 5mm thick each sqm 10.50 845.00 8872.50
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2126
Code Description Unit Quantity Rate Amount
9999 Sundries, wooden wedge for levelling,
cement mortar, Chemical adhesive &
dowel bar (6mm dia) L.S. 37.00 2.12 78.44
LABOUR
For fixing, aligning, locking the panels
0123 Mason Grade -1 day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 9987.94 W
Add 1 % Water charges on "W" 99.88
TOTAL 10087.82 X
Add GST on "X" (multiplying
factor 0.1405) 1417.34
TOTAL 11505.16 Y
Add 15% CPOH on "Y" 1725.77
TOTAL 13230.93 Z
Add Cess @ 1% on "Z" 132.31
Cost of 10 sqm 13363.24
Cost of 1sqm 1336.32
Say 1336.30
26.49.3 Non load bearing panels 75mm thick of required size
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
7998 Factory made EPS light weight
composite sandwitched wall/roof panel
(75mm thick) having core material of
EPS granule balls/beads (conforming
to IS 4671:1984 and shall have density
not less than 15kg per cum). The outer
face on both sides of the panels will be
non asbestos fiber cement board
confirming to IS 14862:2000 or
Calcium silicate board confirming to
EN 14306:2009 of 5mm thick each sqm 10.50 1074.46 11281.83
9999 Sundries, wooden wedge for levelling,
cement mortar, Chemical adhesive &
dowel bar (6mm dia) L.S. 37.00 2.12 78.44
LABOUR
For fixing, aligning, locking the panels
0123 Mason Grade -1 day 0.50 784.00 392.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2127
Code Description Unit Quantity Rate Amount
0114 Beldar day 1.00 645.00 645.00
TOTAL 12397.27 W
Add 1 % Water charges on "W" 123.97
TOTAL 12521.24 X
Add GST on "X" (multiplying
factor 0.1405) 1759.23
TOTAL 14280.48 Y
Add 15% CPOH on "Y" 2142.07
TOTAL 16422.55 Z
Add Cess @ 1% on "Z" 164.23
Cost of 10 sqm 16586.77
Cost of 1sqm 1658.68
Say 1658.70
26.49.4 Non load bearing panels 90mm thick of required size
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
7999 Factory made EPS light weight
composite sandwitched wall/roof panel
(90mm thick) having core material of
EPS granule balls/beads (conforming
to IS 4671:1984 and shall have density
not less than 15kg per cum). The outer
face on both sides of the panels will be
non asbestos fiber cement board
confirming to IS 14862:2000 or
Calcium silicate board confirming to
EN 14306:2009 of 5mm thick each sqm 10.50 1268.00 13314.00
9999 Sundries, wooden wedge for levelling,
cement mortar, Chemical adhesive &
dowel bar (6mm dia) L.S. 37.00 2.12 78.44
LABOUR
For fixing, aligning, locking the panels
0123 Mason Grade -1 day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 14429.44 W
Add 1 % Water charges on "W" 144.29
TOTAL 14573.73 X
Add GST on "X" (multiplying
factor 0.1405) 2047.61
TOTAL 16621.34 Y
Add 15% CPOH on "Y" 2493.20
TOTAL 19114.55 Z
Add Cess @ 1% on "Z" 191.15
Cost of 10 sqm 19305.69
Cost of 1sqm 1930.57
Say 1930.55
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2128
26.49.5 Non load bearing panels 100mm thick of required size
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
8000 Factory made EPS light weight
composite sandwitched wall/roof panel
(100mm thick) having core material of
EPS granule balls/beads (conforming
to IS 4671:1984 and shall have density
not less than 15kg per cum). The outer
face on both sides of the panels will be
non asbestos fiber cement board
confirming to IS 14862:2000 or
Calcium silicate board confirming to
EN 14306:2009 of 5mm thick each sqm 10.50 1512.37 15879.89
9999 Sundries, wooden wedge for levelling,
cement mortar, Chemical adhesive &
dowel bar (6mm dia) L.S. 37.00 2.12 78.44
LABOUR
For fixing, aligning, locking the panels
0123 Mason Grade -1 day 0.50 784.00 392.00
0114 Beldar day 1.00 645.00 645.00
TOTAL 16995.33 W
Add 1 % Water charges on "W" 169.95
TOTAL 17165.28 X
Add GST on "X" (multiplying
factor 0.1405) 2411.72
TOTAL 19577.00 Y
Add 15% CPOH on "Y" 2936.55
TOTAL 22513.55 Z
Add Cess @ 1% on "Z" 225.14
Cost of 10 sqm 22738.69
Cost of 1sqm 2273.87
Say 2273.85
26.50 Providing and fixing in position factory made non asbestos fibre reinforced
aerated cement sandwich wall/roof/floor light weight solid core panels made
of light weight cement concrete core composed of OPC cement, pulverized
flyash, quick lime, cotton pulp & Gypsum in mortar state mixed with aeration
agent in a preset mould. The outer face on both sides of the panels will be non
asbestos fibre cement board confirming to IS 14862:2000. These solid wall panels
are installed using Galvanized iron steel tracks/C channel of 1mm thick of
required sizes as recommended by manufacturer's and fixed to floor and RCC
soffit in plumb to each other with steel screw/fasteners. The panel shall be
fixed vertically with tongue & groove joint with cement based polymer modified
jointing compound. The exposed surface finished with fibre mesh/glass fibre
tape with polymer based jointing compound having superior flexibility. Panels
should be used as floor & roofing with additional structural support, steel or
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2129
RCC depending upon the design. All the operation shall be completed in all
respect as per drawings, Manufacturers specifications and under the overall
direction of Engineer-in-Charge (Cost of all the material is included except
"tracks/C channel" which will be paid separately).
26.50.1 Non load bearing panels 50mm thick of required size (minimum 4mm thick
fibre cement board)
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
0244 Factory made light weight composite
non asbestos fibre reinforced aerated
cement sandwitched wall/roof panel
(50mm thick). The outer face on both
sides of the panels will be non
asbestos fibre cement board (minimum
4mm thick) confirming to IS
14862:2000 sqm 10.50 634.00 6657.00
9999 Sundries, cement based polymer
modified jointing compound, polymer
based jointing compound having
superior flexibility, fibre glass tape etc. L.S. 500.00 2.12 1060.00
LABOUR
For fixing, aligning, locking the panels,
glass fibre tape/fibre mesh with a
jointing compound.
0123 Mason Grade -1 day 1.00 784.00 784.00
0114 Beldar day 2.00 645.00 1290.00
0131 Painter day 0.50 714.00 357.00
TOTAL 10148.00 W
Add 1 % Water charges on "W" 101.48
TOTAL 10249.48 X
Add GST on "X" (multiplying
factor 0.1405) 1440.05
TOTAL 11689.53 Y
Add 15% CPOH on "Y" 1753.43
TOTAL 13442.96 Z
Add Cess @ 1% on "Z" 134.43
Cost of 10 sqm 13577.39
Cost of 1sqm 1357.74
Say 1357.75
26.50.2 Non load bearing panels 75mm thick of required size (minimum 5mm thick
fibre cement board)
Code Description Unit Quantity Rate Amount
Details of cost 10sqm (6.95Nos x
0.6m x2.40m = 10sqm)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2130
Code Description Unit Quantity Rate Amount
MATERIAL
Panel area = 10.00sqm, Add wastage
@ 5% = 0.50sqm, Total area
= 10.50 sqm
0245 Factory made light weight non
asbestos fibre reinforced aerated
cement sandwitched wall/roof panel
(75mm thick). The outer face on both
sides of the panels will be non
asbestos fibre cement board (minimum
5mm thick) confirming to IS
14862:2000 sqm 10.50 789.00 8284.50
9999 Sundries, cement based polymer
modified jointing compound, polymer
based jointing compound having
superior flexibility, fibre glass tape etc. L.S. 500.00 2.12 1060.00
LABOUR
For fixing, aligning, locking the panels,
glass fibre tape/fibre mesh with a
jointing compound.
0123 Mason Grade -1 day 1.00 784.00 784.00
0114 Beldar day 2.00 645.00 1290.00
0131 Painter day 0.50 714.00 357.00
TOTAL 11775.50 W
Add 1 % Water charges on "W" 117.76
TOTAL 11893.26 X
Add GST on "X" (multiplying
factor 0.1405) 1671.00
TOTAL 13564.26 Y
Add 15% CPOH on "Y" 2034.64
TOTAL 15598.90 Z
Add Cess @ 1% on "Z" 155.99
Cost of 10 sqm 15754.88
Cost of 1sqm 1575.49
Say 1575.50
26.51 Supplying of standard quality GFRG panel of 124 mm thickness with modular
cavities purchased from GFRG panel manufacturing plant in the country, cut
to required wall sizes and floor/ roof slab sizes in correct length and height,
including cutting of door, window and ventilator opening as per the cutting
drawing prepared by architects /design engineers for the construction of GFRG
building and loaded in stillages for transportation to the construction site. Cost
of panel includes security deposits, hire charges of stillages & jaws, cost of
transportation in trucks/ lorries without any damages upto 300kms including
all leads and lifts from GFRG manufacturing plant to construction site and
unloading at site using suitable fork lift/ crane. (Payment shall be made on the
basis of area of one side of panel without reduction of opening of door/ window
/ ventilator). For transportation above 300kms, additional charges to be paid.
Code Description Unit Quantity Rate Amount
Detail of cost for 1sqm.
MATERIALS
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2131
Code Description Unit Quantity Rate Amount
Panel area = 1.00sqm, Add wastage
@ 5% = 0.050sqm, Total area
= 1.05 sqm
7368 GFRG panel of 124mm thick sqm 1.05 845.00 887.25
9999 Transportation of panel in suitable
truck (Rs 0.15/sqm/km) upto 300 Km L.S. 26.00 2.12 55.12
9999 Hire Charges for Stillages/Lifting jaw,
unloading of panel at site using for lift
or crane, Hire Charges for Stillages/
Lifting jaw L.S. 17.00 2.12 36.04
TOTAL 978.41 W
Add 1% water charges 9.78
TOTAL 988.19 X
Add GST on "X" (multiplying
factor 0.1405) 138.84
TOTAL 1127.04 Y
Add 15% CPOH on "Y" 169.06
TOTAL 1296.09 Z
Add Cess @1% on "Z" 12.96
Cost of 1 sqm 1309.05
Say 1309.05
26.52 Erection of GFRG Panels in walls in all floors using suitable crane as per
instructions of Engineer-in-Charge, as per cutting drawings and structural
drawings, in perfect line and plumb, above RCC plinth beam/GFRG panel below
and provide necessary lateral/ slanting support to keep the wall panel in safe
position, providing & tieing of Reinforcement as per structural drawings and
applying a coat of water repellant coating Zycosil/equivalent or equivalent
product (1 Zycosil/equivalent compound :10 water ) to saturation level over
RCC plinth beam to provide water proofing treatment to joint between wall
panel & plinth beam as per the guide lines / instruction by the engineer in
charge. (Cost of reinforcement, water proofing of walls and plinth beam/GFRG
panel below joints and installation of door/ window frames before filling of
concrete shall be paid separately). The rate quoted shall include making
provision for laying of lintels, beams, sunshades, staircase beams, lofts,
plumbing work, electrical conduits and any structural insertion etc., as per the
drawing and direction of the engineer in charge. The payment shall be made
based on the actual exposed area (one side only) of the panel. The work shall
be carried out as per the Special Conditions For Glass Fibre Reinforced Gypsum
(GFRG) Structures mentioned in NIT.
Note:
(i) When cutting panel, “A” side is to be for outside or external surface of
respective external wall and B side is to be for internal surface of wall
(ii) Erection of panel is to be with reference to both building plan & cutting
drawing by following notational mark indicated in the cutting drawing as well
as notional mark written on each panel cut as per cutting drawing
Code Description Unit Quantity Rate Amount
Detail of cost for 36sqm. (4 walls of
3mx3m = 36 sqm)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2132
Code Description Unit Quantity Rate Amount
LABOUR
Skilled trained crew erection team
4 persons for 4 hour
0123 Mason (Brick layer) 1st class day 2.00 784.00 1568.00
For 2 Lintels works, 4 skilled men for 2 hrs
0123 Mason (Brick layer) 1st class day 1.00 784.00 784.00
Web cutting for horizontal tie beam,
2 skilled men“ for 4 hrs
0123 Mason (Brick layer) 1st class day 1.00 784.00 784.00
Placing horizontal tie beam
reinforcement 4 men for 2 hrs
0123 Mason (Brick layer) 1st class day 1.00 784.00 784.00
Cost for technical supervisor for 4 hrs
(Technical supervisor = Skilled labour)
0116 Fitter (Grade 1) day 0.50 784.00 392.00
0037 Mobile crane day 0.375 4500.00 1687.50
9999 Hire charge for lateral support &
Lifting jaws L.S. 150.00 2.12 318.00
TOTAL 6317.50 W
Add 1% water charges 63.18
TOTAL 6380.68 X
Add GST on "X" (multiplying
factor 0.1405) 896.48
TOTAL 7277.16 Y
Add 15% CPOH on "Y" 1091.57
TOTAL 8368.73 Z
Add Cess @1% on "Z" 83.69
Cost of 36 sqm 8452.42
Cost of 1 sqm 234.79
Say 234.80
26.53 Filling of empty cavities (as shown in the structural design drawing) with quarry
dust mixed with 5% cement (by volume). After initial infill of 50 mm thick with
M25 concrete at base/bottom of cavities to seal off, infill wall panel cavities in 3
stages as detailed below, (i) 1st pour / infill to be limited to 0.3 to 0.50 m height
from bottom of the panel. (ii) 2nd Pour/ infill: infilling shall be done only after
90 minutes interval between successive pours. The maximum height of infill
shall be restricted to 1.5m height or up to the top level of door / window. (iii)
3rd pour/infill: After an interval of 90 minutes of second pour, infill or pour the
balance height up to the bottom of embedded RCC tie beam.
Pour enough water just required to dampen the dry mix enough to form cake
form after each stage. (cost of laying M25 concrete shall be paid separately) (If
any rain falls in between any stages of concrete pour, make sure to cover the
panel top to prevent ingress of water or water falling into the cavities. In case
of water collection over the concrete inside the panel, drill 10mm hole in GFRG
panel immediately above concrete filled level to drain out water before pour/in-
fill of balance concreting)
Code Description Unit Quantity Rate Amount
Detail of cost for filling one panel size
9 sqm (3mx3m Wall)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2133
Code Description Unit Quantity Rate Amount
MATERIAL
1159 Stone dust/Quarry dust filling in cavities
of size 230x94 mm cum 0.85 1100.00 935.00
0367 OPC Cement @ 5% volume of quarry tonne 0.06091 5000.00 304.55
dust Tools and plants hire charges
0002 Mixer hire charges day 0.125 800.00 100.00
LABOUR
0124 Mason (brick layer) 2nd class day 0.125 714.00 89.25
0114 Beldar day 0.125 645.00 80.63
TOTAL 1509.43 W
Add 1% water charges 15.09
TOTAL 1524.52 X
Add GST on "X" (multiplying
factor 0.1405) 214.19
TOTAL 1738.71 Y
Add 15% CPOH on "Y" 260.81
TOTAL 1999.52 Z
Add Cess @1% on "Z" 20.00
Cost of 0.85 cum 2019.52
Cost of 1 cum 2375.90
Say 2375.90
26.54 Laying of GFRG panel as roof / floor slab panel and staircase panel using
suitable crane as per instructions of Engineer-in-Charge, including providing
support system with 25mm x 300mm-400 mm wide plywood, as runner with
proper prop below proposed micro beams including (a) Cutting of top flange
of panel to 180 mm wide (leaving 25mm projection on either side) to provide
RCC embedded micro beam as per cutting drawings and structural drawings.
(b) Reinforcement for micro beams and tie beams to be provided in position
with proper anchorage as per structural drawings. (c) Provision for Electrical
cabling, fan hooks and laying of pipes for plumbing work. (d) Concreting of
Tie beam, micro beam and top of GFRG panels (50 mm thick) with M-25 cement
concrete mix using coarse aggregate of size less than 20 mm including laying
of 10 gauge 100x100 size weld mesh with 25 mm effective cover from the
panel top.
Code Description Unit Quantity Rate Amount
Detail of cost for 9 sqm (3mx3m
wall panel)
LABOUR
Providing runner & support system in
place for placing panel in position with
40mm bearing on walls( 4 Skilled
persons for 1/2 Hrs /1/16 days)
0123 Mason (Brick layer) 1st class day 0.25 784.00 196.00
Lifting panel from stack by crane and
placing in position with 40 mm bearing
on walls 4 skilled labour for 1 hrs
0123 Mason (Brick layer) 1st class day 0.50 784.00 392.00
Cutting & removal of top flange to
protruding 25mm on either sides for
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2134
Code Description Unit Quantity Rate Amount
keying panel into RCC micro beams in
position (every 3rd cavities runner/span
in place beneath) and providing
concealed beam reinforcement in
position, side shuttering for slab for
external side(with 6mm grove) also to
be provided (mean while providing fan
hooks, electrical cabling, piping etc by
coordinate task by concerned skilled
persons, 4 skilled labour for 1 hrs
0123 Mason (Brick layer) 1st class day 0.50 784.00 392.00
9999 Hire charges for runner and support
system and side shuttering for external
side of slab for 5 days L.S. 29.00 2.12 61.48
0037 Mobile crane day 0.125 4500.00 562.50
TOTAL 1603.98 W
Add 1% water charges 16.04
TOTAL 1620.02 X
Add GST on "X" (multiplying
factor 0.1405) 227.61
TOTAL 1847.63 Y
Add 15% CPOH on "Y" 277.14
TOTAL 2124.78 Z
Add Cess @1% on "Z" 21.25
Cost of 9 sqm 2146.03
Cost of 1 sqm 238.45
Say 238.45
26.55 Supplying and fixing 10 Gauge weld mesh of size 100mm x100 mm for floor/
roof slab concrete screed over the micro beams as reinforcement. The weld
mesh shall be fixed as per drawing.
Code Description Unit Quantity Rate Amount
Detail of cost for 9sqm (3mx3m)
MATERIAL
Mesh area = 9.00sqm, Add wastage @
5% = 0.45sqm, Total area = 9.45 sqm
1223 Steel weld mesh sqm 9.45 150.00 1417.50
Labour for filling the quarry dust
0103 Blacksmith 2nd class day 0.125 714.00 89.25
0114 Beldar day 0.125 645.00 80.63
TOTAL 1587.38 W
Add 1% water charges 15.87
TOTAL 1603.25 X
Add GST on "X" (multiplying
factor 0.1405) 225.26
TOTAL 1828.51 Y
Add 15% CPOH on "Y" 274.28
TOTAL 2102.78 Z
Add Cess @1% on "Z" 21.03
Cost of 9 sqm 2123.81
Cost of 1 sqm 235.98
Say 236.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2135
26.56 Application of ZMB 60/equivalent solution (100 Kg ZMB 60/equivalent, 1 litre
ZMB Nano Thinner, 20 litre water & 1 Litre Zycoprime/equivalent = 122 litre/
kg) over already applied coat of Zycosil/equivalent & Zycoprime/equivalent
solution on the top of all the RCC plinth beams by brush/spray coat before
erection of GFRG over RCC plinth beams in GF. In the case of upper floors
150 mm wide on floor slab for all the external walls, bath/toilet/wet areas (3
hrs drying time) before erection of wall panel on upper floors including
erection of parapet wall.
Code Description Unit Quantity Rate Amount
Detail of cost for 122sqm
MATERIAL
8516 ZMB 60 / equivalent kg 100.00 110.00 11000.00
8517 ZMB Thinner litre 1.00 220.00 220.00
8518 Zycoprime / equivalent litre 1.00 230.00 230.00
9999 Water, brush, technical supervision etc. L.S. 78.00 2.12 165.36
LABOUR
0123 Mason (Brick layer) 1st class day 20.333 784.00 15941.07
TOTAL 27556.43 W
Add 1% water charges 275.56
TOTAL 27832.00 X
Add GST on "X" (multiplying
factor 0.1405) 3910.40
TOTAL 31742.39 Y
Add 15% CPOH on "Y" 4761.36
TOTAL 36503.75 Z
Add Cess @1% on "Z" 365.04
Cost of 122 sqm 36868.79
Cost of 1 sqm 302.20
Say 302.20
26.57 After erection of GFRG wall panels, seal all GFRG wall joints with paper tape
temporarily. Water proofing treatment of vertical joints with Zycosil/
equivalent water proofing Solution (1 litre of Zycosil/equivalent & 20 litres of
water stirred first & 2 litres of Zycoprime/equivalent added and stirred (total
23 litres)) with 50 ml syringe till the gap and in filled concrete is completely
saturated. After removing the paper seal, seal off the vertical joints with water
proofing material "Grout RW/equivalent " (Sealing cost excluded.)
Code Description Unit Quantity Rate Amount
Detail of cost for 3 metre
MATERIAL
8519 Zycosil /equivalent litre 0.02609 1800.00 46.96
8518 Zycoprime / equivalent litre 0.05217 230.00 12.00
9999 water, syringe, etc. L.S. 16.00 2.12 33.92
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2136
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (Brick layer) 1st class day 0.125 784.00 98.00
TOTAL 190.88 W
Add 1% water charges 1.91
TOTAL 192.79 X
Add GST on "X" (multiplying
factor 0.1405) 27.09
TOTAL 219.88 Y
Add 15% CPOH on "Y" 32.98
TOTAL 252.86 Z
Add Cess @1% on "Z" 2.53
Cost of 3 metre 255.39
Cost of 1 metre 85.13
Say 85.15
26.58 Filling of joints between RCC plinth beam / floor slab and wall panel of external
walls, toilet / bath room / wet areas walls on all floor and parapet wall over
roof slab, stair case head room at the time of erection of GFRG panels with
Grout RW/equivalent sealant compound after the erection of panel before
the infill of concrete in panel cavities and fine finish. This applies for all
horizontal and vertical joints between GFRG wall and slab panels.
Code Description Unit Quantity Rate Amount
Detail of cost for 48 metre
MATERIAL
8520 Elastobar / equivalent kg 1.00 300.00 300.00
0367 OPC Cement tonne 0.0015 5000.00 7.50
9999 100 mesh silica, water, technical
supervision, etc. L.S. 3.00 2.12 6.36
LABOUR
0123 Mason (Brick layer) 1st class day 1.500 784.00 1176.00
TOTAL 1489.86 W
Add 1% water charges 14.90
TOTAL 1504.76 X
Add GST on "X" (multiplying
factor 0.1405) 211.42
TOTAL 1716.18 Y
Add 15% CPOH on "Y" 257.43
TOTAL 1973.60 Z
Add Cess @1% on "Z" 19.74
Cost of 48 metre 1993.34
Cost of 1 metre 41.53
Say 41.55
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2137
26.59 Water proofing treatment of Vertical joints (of external side and internal side)
between door frame, window & ventilator frames (on all four sides) of outer
wall over the Zycosil/equivalent & Zycoprime/equivalent solution already
applied (before the installation of door / window / ventilator frames in position)
and fine finish with Grout RW/equivalent.
Code Description Unit Quantity Rate Amount
Detail of cost for 40 sqm
MATERIAL
8519 Zycosil / equivalent litre 1.00 1800.00 1800.00
8518 Zycoprime / equivalent litre 2.00 230.00 460.00
9999 Water, technical supervision, etc. L.S. 6.00 2.12 12.72
LABOUR
0123 Mason (Brick layer) 1st class day 0.28571 784.00 224.00
Cost of 40 sqm 2496.72
Cost of 1 metre (10mm thick) 0.62 A1
Detail of cost for 48 metre
MATERIAL
8520 Elastobar / equivalent kg 1.00 300.00 300.00
0367 OPC Cement tonne 0.0015 5000.00 7.50
9999 100 mesh silica, water, technical
supervision, etc. L.S. 3.00 2.12 6.36
LABOUR
0123 Mason (Brick layer) 1st class day 1.50 784.00 1176.00
Cost of 48 metre 1489.86
Cost of 1 metre 31.04 A2
TOTAL (A1+A2) 31.66 W
Add 1% water charges 0.32
TOTAL 31.98 X
Add GST on "X" (multiplying
factor 0.1405) 4.49
TOTAL 36.47 Y
Add 15% CPOH on "Y" 5.47
TOTAL 41.94 Z
Add Cess @1% on "Z" 0.42
Cost of 1 metre 42.36
Say 42.35
26.60 Water proofing treatment of RCC sunshade with Zycosil/equivalent water
proofing Solution (1 litre of Zycosil/equivalent & 20 litres of water stirred first
& 2 litres of Zycoprime/equivalent added and stirred (total 23 litres)) till it
meets the saturation level and testing as per RILEM or by water drops test in
which water drops do not absorb but drops remain or rolls.
Code Description Unit Quantity Rate Amount
Detail of cost for 40 sqm
MATERIAL
8519 Zycosil / equivalent litre 1.00 1800.00 1800.00
8518 Zycoprime /equivalent litre 2.00 230.00 460.00
9999 Water, technical supervision, etc. L.S. 7.00 2.12 14.84
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2138
Code Description Unit Quantity Rate Amount
LABOUR
0131 Painter day 2.50 714.00 1785.00
TOTAL 4059.84 W
Add 1% water charges 40.60
TOTAL 4100.44 X
Add GST on "X" (multiplying
factor 0.1405) 576.11
TOTAL 4676.55 Y
Add 15% CPOH on "Y" 701.48
TOTAL 5378.03 Z
Add Cess @1% on "Z" 53.78
Cost of 40 sqm 5431.81
Cost of 1 sqm 135.80
Say 135.80
26.61 In-filling / sealing of joint between RCC lintel cum sunshade and wall (on
external side) in all floors by pushing in Grout RW/equivalent in paste form
and coving 20 mm x 20 mm after applying a coat of Zycosil/equivalent &
zycoprime/equivalent solution before cement plastering of top, bottom and
sides of RCC sunshade.
Code Description Unit Quantity Rate Amount
Detail of cost for 40 sqm
MATERIAL
8519 Zycosil / equivalent litre 1.00 1800.00 1800.00
8518 Zycoprime / equivalent litre 2.00 230.00 460.00
9999 Water, technical supervision, etc. L.S. 6.00 2.12 12.72
LABOUR
0123 Mason (Brick layer) 1st class day 0.28571 784.00 224.00
Cost of 40 sqm 2496.72
Cost of 1 metre (10mm thick) 0.62 A1
Detail of cost for 48 metre
MATERIAL
8520 Elastobar / equivalent kg 1.00 300.00 300.00
0367 OPC Cement tonne 0.0015 5000.00 7.50
9999 100 mesh silica, water, technical
supervision, etc. L.S. 3.00 2.12 6.36
LABOUR
0123 Mason (Brick layer) 1st class day 1.50 784.00 1176.00
Cost of 48 metre 1489.86
Cost of 1 metre 31.04 A2
TOTAL (A1+A2) 31.66 W
Add 1% water charges 0.32
TOTAL 31.98 X
Add GST on "X" (multiplying
factor 0.1405) 4.49
TOTAL 36.47 Y
Add 15% CPOH on "Y" 5.47
TOTAL 41.94 Z
Add Cess @1% on "Z" 0.42
Cost of 1 metre 42.36
Say 42.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2139
26.62 Designing, Providing, installing and fixing factory finished customed design
pregalvanized high tensile steel joists manufactured from G350 Z275
confirming to IS:277-1992, minimum coating of galvanizing 275 gm/sqm,
minimum yield stress 35 MPa & minimum tensile strength of 380 MPa placed
1.23 metre apart to support the load of slab etc as per the design & directions
of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 212.816 kgs
MATERIAL
Covered area = 5.57x4.2m = 23.394 sqm
(a) 250 series Joist (G 350) - 3mm
thick - Galvanised = 4 Nos x4.18 metre
length = 16.72 metre @ 10.59 kg/metre
= 177.06 kg
(b) Joist Shoe plate (E 250) - 12 mm
thick MS Plate (Galvanised with 55
microns) = 2 Nos in each joist x 4 No.
joist = 8 No's @ 2.4kg/each = 19.2kg
(c) Bolts (M16 - Gr 8.8s),
(Galvanised) (16? X 40 bolts With
washer & Nuts)= 6No's in each joist x
4 No. joists=24 Nos 24
No'[email protected]/each = 3.24 kg
(d) Hanging Angle at corners to support
lock bars L 75x40x1.6 (Galvanised) =
2x4.18 metre =8.36 metre @ 1.60kg/
metre = 13.376 kg
Total weight = 177.06+19.2+3.24+
13.376 = 212.816 kgs
1012 Pregalvanized high tensile steel kg 212.816 90.00 19153.44
LABOUR (Reference item no 10.1)
0116 Fitter (grade 1) day 1.064 784.00 834.18
0103 Blacksmith 2nd class day 1.596 714.00 1139.54
0114 Beldar day 2.128 645.00 1372.56
Total 22499.72 W
Add 1 % Water charges on "W" 225.00
TOTAL 22724.72 X
Add GST on "X" (multiplying
factor 0.1405) 3192.82
TOTAL 25917.54 Y
Add 15% CPOH on "Y" 3887.63
TOTAL 29805.17 Z
Add Cess @ 1% on "Z" 298.05
Cost of 212.816 kgs 30103.22
Cost of 1 kg 141.45
Say 141.45
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2140
26.63 Providing and fixing special adjustable lockbars of mild steel E-250 to support
the temporary plywood for work between joists during construction as per
design & directions of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Detail of cost for 298.75 kgs
MATERIAL
Assuming special adjustable lock bar
of mild steel will become unserviceable
after use of 50 times
Taking salvage value after full use of
material @ 35% of cost
Lock bar of size 1230mmx75mmx10mm
45 Nos x 4.35kg/each = 195.75 kg.
Lock bar of size 930mmx75mmx10mm
30 Nos x 3.3kg/each = 99.00 kg.
Total weight = 298.75 kgs
Assuming 50 repetition, Qty taken for
cost of using once = 298.75/50
= 5.975 kgs
Considering salvage value @ 35%,
Quantity = 5.975x(100-35)/100 =
3.88 kgs
7336 Lock Bar (E 250) - 10 thick MS Plate kgs 3.88 76.00 294.88
LABOUR (Reference item no 10.1)
0116 Fitter (grade 1) day 1.49 784.00 1168.16
0103 Blacksmith 2nd class day 2.24 714.00 1599.36
0114 Beldar day 2.99 645.00 1928.55
Total 4990.95 W
Add 1 % Water charges on "W" 49.91
TOTAL 5040.86 X
Add GST on "X" (multiplying
factor 0.1405) 708.24
TOTAL 5749.10 Y
Add 15% CPOH on "Y" 862.37
TOTAL 6611.47 Z
Add Cess @ 1% on "Z" 66.11
Cost of 298.75 kgs 6677.58
Cost of 1 kg 22.35
Say 22.35
26.64 Centering and shuttering with 12mm thick shuttering plywood confirming to
IS 4990:2011 and removal of form at all heights. Plywood will be supported
on lock bars.
26.64.1 Suspended floors, roofs, landings, balconies and access platform.
Code Description Unit Quantity Rate Amount
Detail of cost for 13.50 sqm
MATERIAL
Assuming 12mm thick plywood will
become unserviceable after use of
10 times
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2141
Code Description Unit Quantity Rate Amount
Area of roof = 13.50 sqm + Add
wastage @ 5% = 0.675 sqm.
Total = 14.175 sqm.
Qty taken for cost using once
= 14.175/10 = 1.4175 sqm
8659 12mm thick waterproofing plywood
confirming to IS 4990:2011 sqm 1.4175 525.00 744.19
LABOUR (Reference item no 5.9.20)
0112 Carpenter 2nd class day 0.125 714.00 89.25
0114 Beldar day 0.125 645.00 80.63
Total 914.06 W
Add 1 % Water charges on "W" 9.14
TOTAL 923.20 X
Add GST on "X" (multiplying
factor 0.1405) 129.71
TOTAL 1052.91 Y
Add 15% CPOH on "Y" 157.94
TOTAL 1210.85 Z
Add Cess @ 1% on "Z" 12.11
Cost of 13.50 sqm 1222.96
Cost of 1 sqm 90.59
Say 90.60
26.65 Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck
sheet confirming to IS 277:1992 used as permanent shuttering over which
MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with
concrete. This metal deck will be supported on structural steel beam with
shear studs. (Structural steel like Beam, column, joists etc. & concrete of
different grade as per design will be paid separately).
Code Description Unit Quantity Rate Amount
Detail of cost for 10 sqm
MATERIAL
Weight of GI sheet for 10sqm
= 76.7 kgs + Add wastage @ 3%
= 2.3 kg. Total = 79.00 kg
8019 GI sheet 0.8 mm thick confirming to
IS 277:1992 kg 79.00 90.00 7110.00
Length wire mesh 200metre/10 sqm.
Weight of wire @ 0.06 kg/m. total
weight = 12 kgs + Add wastage @ 5%
= 0.6 kgs. Total 12.6 kg
1217 GI Wire mesh 100x100 mm kg 12.60 75.00 945.00
2314 Carriage of sheet & wire tonne 0.0916 145.72 13.35
1218 Shear stud each 40.00 50.00 2000.00
9999 Nails/Tagged screws L.S. 138.70 2.12 294.04
9999 Labour for fixing shear stud L.S. 462.40 2.12 980.29
Labour for sheeting
(Ref item no 26.19.1)
0130 Mistry day 0.108 784.00 84.67
0112 Carpenter 2nd class day 0.432 714.00 308.45
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2142
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.432 645.00 278.64
Labour for laying wire mesh
(Ref item no 5.22.2)
0102 Blacksmith 1st class day 0.12 784.00 94.08
0114 Beldar day 0.120 645.00 77.40
Total 12185.92 W
Add 1 % Water charges on "W" 121.86
TOTAL 12307.78 X
Add GST on "X" (multiplying
factor 0.1405) 1729.24
TOTAL 14037.02 Y
Add 15% CPOH on "Y" 2105.55
TOTAL 16142.58 Z
Add Cess @ 1% on "Z" 161.43
Cost of 10 sqm 16304.00
Cost of 1 sqm 1630.40
Say 1630.40
26.66 Providing and fixing in position, 130 mm thick factory made Expanded
Polystyrene Core (EPS Core) wall panels consisting of EPS core sandwiched
between two Engineered sheets of welded wire fabric mesh duly finished
with shortcrete materials on outer faces. The fabric mesh shall be made of 3
mm dia zinc coated G.I. wire mesh with 50 mm pitch in both the directions
and on both faces of the wall and connected by GI wire of 3mm dia at alternate
row by welding. The EPS core shall consist of 60 mm thick EPS of density
not less than 16 kg/ per cum. Both the outer faces of the panel shall be finished
by applying the layer of 35 mm thick cement mortar 1:3 {1 cement: 3 coarse
sand (not having more than 40% stone chips of size upto 6 mm)} with the
help of shotcreting/guniting equipment etc at a pressure not less than 1 bar
(100KN/m2) and both surfaces finished with trowel. Fixing operations of wall
panels shall be completed in all respect as per drawings and specifications
and under the overall direction of the Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 1.20x3.00m
= 3.60 sqm
MATERIAL
Area of EPS panel = 3.60 sqm +
Add wastage @5%. Total = 3.78 sqm
8020 Factory made EPS Core wall panel /
roof panel sandwiched between two
Engineered welded wire fabric mesh of
3 mm dia G.I. wire mesh, with 50 mm
pitch in both the directions, connected
by G.I. wire of 3mm dia at alternate
row by welding sqm 3.78 600.00 2268.00
9999 Add for L-shape, U-shape & straight
lap mesh L.S. 208 2.12 440.96
Cement mortar 1:3 (1cement:3 coarse
sand) 2x1.20x3.00x0.035= 0.252 cum
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2143
Code Description Unit Quantity Rate Amount
3.8 Rate as per Item No.3.8 of SH: Mortar cum 0.252 5024.15 1266.09
10 mm TMT bars 8 nos of 0.60 metre
long. Total length = 4.8 m @ 0.617 kg/
metre. Total weight = 2.96 kg
5.22.6 Rate as per 5.22.6 (SH:5 Reinforced
Cement Concrete) kg 2.9600 89.65 265.36 A
9999 Tag screw with washers for wire mesh
fixing L.S. 78 2.12 165.36
9999 For fixing wall with foundation L.S. 312.15 2.12 661.76
LABOUR
9999 For carrying out shotcreting, shoring,
leveling, and finishing the surface with
trowel. L.S. 707.5 2.12 1499.90
Total 6567.43 W
Add 1 % Water charges on "W-A" 63.02
TOTAL 6630.45 X
Add GST on "X-A" (multiplying
factor 0.1405) 894.29
TOTAL 7524.74 Y
Add 15% CPOH on "Y-A" 1088.91
TOTAL 8613.65 Z
Add Cess @ 1% on "Z-A" 83.48
Cost of 3.6 sqm 8697.13
Cost of 1 sqm 2415.87
Say 2415.85
26.67 Providing and fixing of external thermal insulation and composite system
with First layer of self-extinguishing type Expanded Polystyrene (EPS)
insulation boards of 120 mm thick ( max 1mX0.5m section), confirming to IS
4671:1984, having thermal conductivity of 0.034 W/mK, (measured as per IS
3346-1980), density of 20-24 kg/m³ measured as per IS 5688-1982, Fire retardant
property self-extinguishing type as per EN 13501-1, bonded with special
polymer modified cementitious adhesive confirming to EOTA ETAG 004
(European Technical Approval) formulated to bond polystyrene insulation
boards to typical mineral substrate (according to ETAG 004) and
Polypropylene mechanical fasteners with plastic pin confirming to EOTA
ETAG 014 (European Technical Approval) having dia 10mm & L=200mm on
finished level wall and the junction between two adjacent EPS boards to be
sealed with low expansion moisture cure Polyurethane Foam. Second layer
consists of Fiberglass mesh covered with alkali-resistant coating, mass per
unit area ?145 gm/m², mesh size: 3.9x4.0 mm ±10% embedded in special
polymer modified cementitious Base Coat with hydrophobes and the corners
will be protected with Corner-beads with alkali-resistant mesh wings at least
10 cm wide, mesh mass per unit area min 145 gm/m². The surface will be
levelled, finished, made smooth complete in all respect as per manufactures
specification and as per directions of Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
Material
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2144
Code Description Unit Quantity Rate Amount
Area of insulation board = 10 sqm +
Add wastage @ 10% = 1 sqm.
Total = 11.00 sqm
8562 Expanded Polystyrene insulation board
120 mm thick confirming to IS 4671-
1984, Fire retardant property self-
extinguishing type as per EN 13501-1 sqm 11.00 825.00 9075.00
1252 Cementitious polymer base adhesive
confirming to EOTA ETAG 004
(European Technical Approval) kg 50.00 34.00 1700.00
1253 Polypropylene mechanical fastener
with plastic pin confirming to EOTA
ETAG 014 (European Technical
Approval) having dia 10mm &
L=200mm each 100.00 30.00 3000.00
1254 Moisture cure Polyurethane Foam 750 ml 0.80 600.00 480.00
1255 PVC Corner Bead of size 25mmx25mm
fixed with glass fibre mesh (100mm x
100mm) metre 5.00 90.00 450.00
1256 Cementitious polymer base coat
confirming to EOTA ETAG 004
(European Technical Approval) kg 50.00 40.00 2000.00
1257 Fiberglass mesh with alkali-resistant
coating having mass per unit area >
145 g/m2, mesh size: 3.9x4.0 mm
±10% sqm 10.00 75.00 750.00
Labour
0131 Painter day 4.00 714.00 2856.00
0114 Beldar day 4.00 645.00 2580.00
9999 Trowel, Angle Float, Brushes, sand
paper etc. L.S. 72.25 2.12 153.17
9999 Sundries (PVC drip bead with glass
fibre mesh wing (100mm x 100mm),
expansion joint, starter track of 1mm
thick aluminium alloy (120mm wide),
polyurethane sealent, scaffolding etc.) L.S. 1445.09 2.12 3063.59
Total 26107.76 W
Add 1 % Water charges on "W" 261.08
TOTAL 26368.84 X
Add GST on "X" 3704.82
TOTAL 30073.66 Y
Add 15% CPOH on "Y" 4511.05
TOTAL 34584.71 Z
Add Cess @ 1% on "Z" 345.85
Cost of 10 sqm 34930.56
Cost of 1 sqm 3493.06
Say 3493.05
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2145
26.68 Providing and laying factory made Precast concrete solid blocks of 200 mm
thickness of grade M10 made of C&D waste from approved manufacturer in
foundation and plinth in:
26.68.1 Cement mortar 1:6 (1 cement : 6 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
MATERIAL:
8658 Precast C&D waste concrete block 1000 Nos 0.1109 25150.00 2789.14
2201 Carriage of blocks 1000 Nos 0.1109 437.15 48.48
Cement mortar 1 : 6 (1 cement :
6 coarse sand)
3.11 Rate as per item No 3.11 of SH: Mortar cum 0.113 3686.30 416.55
9999 Sundries L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.33 784.00 258.72
0124 Mason (brick layer) 2nd class day 0.33 714.00 235.62
0115 Coolie day 1.00 645.00 645.00
0101 Bhisti day 0.18 714.00 128.52
Total 4527.81 W
Add 1 % Water charges on "W" 45.28
TOTAL 4573.09 X
Add GST on "X" (multiplying
factor 0.1405) 642.52
TOTAL 5215.61 Y
Add 15% CPOH on "Y" 782.34
TOTAL 5997.95 Z
Add Cess @ 1% on "Z" 59.98
Cost of 1 cum 6057.93
Say 6057.95
26.69 Providing and laying factory made Precast concrete solid blocks of 200 mm
thickness of grade M10 made of C&D waste from approved manufacturer in
superstructure above plinth level up to floor V level
26.69.1 Cement mortar 1:6 (1 cement : 6 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for 1 cum
MATERIAL:
8658 Precast C&D waste concrete block 1000 Nos 0.1109 25150.00 2789.14
2201 Carriage of blocks 1000 Nos 0.1109 437.15 48.48
Cement mortar 1 : 6 (1 cement :
6 coarse sand)
3.11 Rate as per item No 3.11 of SH: Mortar cum 0.113 3686.30 416.55
9999 Sundries L.S. 2.73 2.12 5.79
LABOUR
0123 Mason (brick layer) 1st class day 0.47 784.00 368.48
0124 Mason (brick layer) 2nd class day 0.47 714.00 335.58
0115 Coolie day 1.80 645.00 1161.00
0101 Bhisti day 0.20 714.00 142.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2146
Code Description Unit Quantity Rate Amount
9999 Scaffolding L.S. 22.36 2.12 47.40
Extra labour element required for lifting
of materials (above floor two level upto
floor five level)
0115 Coolie day 1.13 645.00 728.85
Total 6044.07 W
Add 1 % Water charges on "W" 60.44
TOTAL 6104.51 X
Add GST on "X" (multiplying
factor 0.1405) 857.68
TOTAL 6962.19 Y
Add 15% CPOH on "Y" 1044.33
TOTAL 8006.52 Z
Add Cess @ 1% on "Z" 80.07
Cost of 1 cum 8086.59
Say 8086.60
26.70 Providing and laying half block masonry with factory made Precast concrete
solid blocks of 100 mm thickness of grade M10 made of C&D waste from
approved manufacturer in foundation and plinth in:
26.70.1 Cement mortar 1:4(1 cement : 4 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL:
8658 Precast C&D waste concrete block 1000 Nos 0.1161 25150.00 2919.92
2201 Carriage of blocks 1000 Nos 0.1161 437.15 50.75
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per item No 3.9 of SH: Mortar cum 0.0708 4355.20 308.35
9999 Sundries L.S. 13.52 2.12 28.66
LABOUR
0123 Mason (brick layer) 1st class day 0.45 784.00 352.80
0124 Mason (brick layer) 2nd class day 0.45 714.00 321.30
0115 Coolie day 1.55 645.00 999.75
0101 Bhisti day 0.70 714.00 499.80
Total 5481.33 W
Add 1 % Water charges on "W" 54.81
TOTAL 5536.14 X
Add GST on "X" (multiplying
factor 0.1405) 777.83
TOTAL 6313.97 Y
Add 15% CPOH on "Y" 947.10
TOTAL 7261.07 Z
Add Cess @ 1% on "Z" 72.61
Cost of 10 sqm 7333.68
Cost of 1 sqm 733.37
Say 733.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2147
26.71 Providing and laying half block masonry with factory made Precast concrete
solid blocks of 100 mm thickness of grade M10 made of C&D waste from
approved manufacturer in superstructure above plinth level up to floor V level:
26.71.1 Cement mortar 1:4 (1 cement : 4 coarse sand)
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL:
8658 Precast C&D waste concrete block 1000 Nos 0.1161 25150.00 2919.92
2201 Carriage of blocks 1000 Nos 0.1161 437.15 50.75
Cement mortar 1 : 4 (1 cement :
4 coarse sand)
3.9 Rate as per item No 3.9 of SH: Mortar cum 0.0708 4355.20 308.35
9999 Sundries L.S. 13.52 2.12 28.66
LABOUR
0123 Mason (brick layer) 1st class day 0.60 784.00 470.40
0124 Mason (brick layer) 2nd class day 0.60 714.00 428.40
0115 Coolie day 2.00 645.00 1290.00
0101 Bhisti day 0.70 714.00 499.80
Extra labour for lifting materials:
0115 Coolie day 1.29 645.00 832.05
Total 6828.33 W
Add 1 % Water charges on "W" 68.28
TOTAL 6896.61 X
Add GST on "X" (multiplying
factor 0.1405) 968.97
TOTAL 7865.59 Y
Add 15% CPOH on "Y" 1179.84
TOTAL 9045.42 Z
Add Cess @ 1% on "Z" 90.45
Cost of 10 sqm 9135.88
Cost of 1 sqm 913.59
Say 913.60
26.72 Providing and laying 60mm thick factory made cement concrete paver block
of approved shape and colour of M -30 grade made of C&D waste by block
making machine with vibratory compaction laid in required pattern and
including over 50mm thick compacted bed of coarse sand, filling the joints
with fine sand etc. all complete as per the direction of Engineer-in-charge.
Code Description Unit Quantity Rate Amount
Details of cost for 10 sqm
MATERIAL:
7776 Concrete paver block of grade M-30
made of C&D waste (60mm thickness) sqm 10.00 295.00 2950.00
Bedding layer - 50mm thick
10x0.050=0.50 cum
0982 Coarse sand (zone III) cum 0.50 1500.00 750.00
2203 Carriage of Coarse sand cum 0.50 163.93 81.97
0983 Fine sand (zone IV) cum 0.15 900.00 135.00
2261 Carriage of fine sand cum 0.15 163.93 24.59
Laying charges (Based on actual
observation)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2148
Code Description Unit Quantity Rate Amount
LABOUR
0123 Mason (brick layer) 1st class day 0.50 784.00 392.00
0124 Mason (brick layer) 2nd class day 0.50 714.00 357.00
0114 Beldar day 1.00 645.00 645.00
0115 Coolie day 0.50 645.00 322.50
Total 5658.05 W
Add 1 % Water charges on "W" 56.58
TOTAL 5714.64 X
Add GST on "X" (multiplying
factor 0.1405) 802.91
TOTAL 6517.54 Y
Add 15% CPOH on "Y" 977.63
TOTAL 7495.17 Z
Add Cess @ 1% on "Z" 74.95
Cost of 10 sqm 7570.12
Cost of 1 sqm 757.01
Say 757.00
26.73 Fabrication & Manufacturing of Prestressed Hollow Core slab (Hollow area
25 to 30%) of different thickness & modular width 1200 mm in Controlled
Factory Environment with approved methodology confirming to IS 10297:1982
by using long line casting method having arrangement of proper steel bed.
Concreting should be done by batch mixing plant capable of producing zero
slump concrete, transported through automatic shuttels of standard make &
layed on bed with the help of extruder/Slipformer, finishing, curing and also
provision of steam curing. Cutting, making necessary cutout/holes of required
sizes for services in slab element after achieving required strength, yard
handling & stacking all complete as per approved shop drawings & design
mix as per the direction of the Engineer-in-charge. (Cost of strands should
be paid separately).
Note: Excess/less cement over the specified cement content used as per design
mix is payable/recoverable separately)
26.73.1 Concrete Grade-M-40 (cement content 400 kg )
26.73.1.1 100 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 10.80 cum (120 Rmt )
120 Rmt X 1.20 m X .10 (25 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of SH RCC cum 10.80 10730.90 115893.72 A
5.35 Rate as per item no 5.35 of SH RCC quintal 5.40 688.45 3717.63 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 10.80 500.00 5400.00
9999 Extra cost for preparing zero slump
concrete L.S. 936.00 2.12 1984.32
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2149
Code Description Unit Quantity Rate Amount
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.10)=312) sqm 312.00 57.50 17940.00 A
TOTAL 148946.71 W
Add 1 % Water charges on "W-A" 113.95
TOTAL 149060.66 X
Add GST on "X-A" (multiplying
factor 0.1405) 1617.06
TOTAL 150677.72 Y
Add 15% CPOH on "Y-A" 1968.96
TOTAL 152646.68 Z
Add Cess @ 1% on "Z-A" 150.95
Cost of 120 metre 152797.63
Cost of 1 metre 1273.31
Say 1273.30
26.73.1.2 120 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 12.96 cum (120 Rmt )
120 Rmt X 1.20 m X .12 (25 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of SH RCC cum 12.96 10730.95 139072.46 A
5.35 Rate as per item no 5.35 of SH RCC quintal 6.48 688.45 4461.16 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 12.96 500.00 6480.00
9999 Extra cost for preparing zero slump
concrete L.S. 1124.00 2.12 2382.88
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.12)=316.80) sqm 316.80 57.50 18216.00 A
TOTAL 174623.54 W
Add 1 % Water charges on "W-A" 128.74
TOTAL 174752.28 X
Add GST on "X-A" (multiplying
factor 0.1405) 1826.87
TOTAL 176579.15 Y
Add 15% CPOH on "Y-A" 2224.43
TOTAL 178803.58 Z
Add Cess @ 1% on "Z-A" 170.54
Cost of 120 metre 178974.12
Cost of 1 metre 1491.45
Say 1491.45
26.73.1.3 150 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 16.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.15 (25 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of SH RCC cum 16.20 10730.90 173840.58 A
5.35 Rate as per item no 5.35 of SH RCC quintal 8.10 688.45 5576.45 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2150
Code Description Unit Quantity Rate Amount
0031 Steam curing by using boiler /Heater cum 16.20 500.00 8100.00
9999 Extra cost for preparing zero slump
concrete L.S. 1405.00 2.12 2978.60
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.15)=324.00) sqm 324.00 57.50 18630.00 A
TOTAL 213136.67 W
Add 1 % Water charges on "W-A" 150.90
TOTAL 213287.56 X
Add GST on "X-A" (multiplying
factor 0.1405) 2141.30
TOTAL 215428.86 Y
Add 15% CPOH on "Y-A" 2607.27
TOTAL 218036.13 Z
Add Cess @ 1% on "Z-A" 199.89
Cost of 120 metre 218236.02
Cost of 1 metre 1818.63
Say 1818.65
26.73.1.4 200 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 20.160 cum (120 Rmt )
120 Rmt X 1.20 m X0.20 (30 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of SH RCC cum 20.16 10730.90 216334.94 A
5.35 Rate as per item no 5.35 of SH RCC quintal 10.08 688.45 6939.58 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 20.16 500.00 10080.00
9999 Extra cost for preparing zero slump
concrete L.S. 1748.00 2.12 3705.76
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.20)=336.00) sqm 336.00 57.50 19320.00 A
TOTAL 260391.32 W
Add 1 % Water charges on "W-A" 177.97
TOTAL 260569.29 X
Add GST on "X-A" (multiplying
factor 0.1405) 2525.45
TOTAL 263094.74 Y
Add 15% CPOH on "Y-A" 3075.03
TOTAL 266169.78 Z
Add Cess @ 1% on "Z-A" 235.75
Cost of 120 metre 266405.53
Cost of 1 metre 2220.05
Say 2220.05
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2151
26.73.1.5 250 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 25.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.25 (30 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of
SH RCC cum 25.20 10730.90 270418.68 A
5.35 Rate as per item no 5.35 of SH RCC quintal 12.60 688.45 8674.47 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 25.20 500.00 12600.00
9999 Extra cost for preparing zero slump
concrete L.S. 2185.00 2.12 4632.20
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.25)=348.00) sqm 348.00 57.50 20010.00 A
TOTAL 320346.39 W
Add 1 % Water charges on "W-A" 212.43
TOTAL 320558.82 X
Add GST on "X-A" (multiplying
factor 0.1405) 3014.52
TOTAL 323573.34 Y
Add 15% CPOH on "Y-A" 3670.53
TOTAL 327243.87 Z
Add Cess @ 1% on "Z-A" 281.41
Cost of 120 metre 327525.28
Cost of 1 metre 2729.38
Say 2729.40
26.73.1.6 300 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 30.24 cum (120 Rmt )
120 Rmt X 1.20 m X 0.30 (30 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of
SH RCC cum 30.24 10730.90 324502.42 A
5.35 Rate as per item no 5.35 of SH RCC quintal 15.12 688.45 10409.36 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 30.24 500.00 15120.00
9999 Extra cost for preparing zero slump
concrete L.S. 2622.00 2.12 5558.64
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.30)=360.00) sqm 360.00 57.50 20700.00 A
TOTAL 380301.46 W
Add 1 % Water charges on "W-A" 246.90
TOTAL 380548.36 X
Add GST on "X-A" (multiplying
factor 0.1405) 3503.59
TOTAL 385051.95 Y
Add 15% CPOH on "Y-A" 4266.02
TOTAL 388317.97 Z
Add Cess @ 1% on "Z-A" 327.06
Cost of 120 metre 388645.03
Cost of 1 metre 3238.71
Say 3238.70
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2152
26.73.1.7 350 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 35.28 cum (120 Rmt )
120 Rmt X 1.20 m X 0.35 (30 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of
SH RCC cum 35.28 10730.90 378586.15 A
5.35 Rate as per item no 5.35 of SH RCC quintal 17.64 688.45 12144.26 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 35.28 500.00 17640.00
9999 Extra cost for preparing zero slump
concrete L.S. 3059.00 2.12 6485.08
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.35)=372.00) sqm 372.00 57.50 21390.00 A
TOTAL 440256.53 W
Add 1 % Water charges on "W-A" 281.36
TOTAL 440537.89 X
Add GST on "X-A" (multiplying
factor 0.1405) 3992.66
TOTAL 444530.55 Y
Add 15% CPOH on "Y-A" 4861.52
TOTAL 449392.07 Z
Add Cess @ 1% on "Z-A" 372.72
Cost of 120 metre 449764.78
Cost of 1 metre 3748.04
Say 3748.05
26.73.1.8 400 mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 40.32 cum (120 Rmt )
120 Rmt X 1.20 m X 0.40 (30 % hollow)
5.33.2.4 Rate as per item no 5.33.2.4 of
SH RCC cum 40.32 10730.90 432669.89 A
5.35 Rate as per item no 5.35 of SH RCC quintal 20.16 688.45 13879.15 A
9999 Hollow core bed cost L.S. 1301.00 2.12 2758.12
0031 Steam curing by using boiler /Heater cum 40.32 500.00 20160.00
9999 Extra cost for preparing zero slump
concrete L.S. 3496.00 2.12 7411.52
9999 Cutting, marking, lifting & transportation L.S. 578.00 2.12 1225.36
9999 Sundries L.S. 13.00 2.12 27.56
5.41.1 Rate as per item no 5.41.1 of
SH RCC (120x2x(1.20+0.40)=384.00) sqm 384.00 57.50 22080.00 A
TOTAL 500211.60 W
Add 1 % Water charges on "W-A" 315.83
TOTAL 500527.43 X
Add GST on "X-A" (multiplying
factor 0.1405) 4481.72
TOTAL 505009.15 Y
Add 15% CPOH on "Y-A" 5457.02
TOTAL 510466.17 Z
Add Cess @ 1% on "Z-A" 418.37
Cost of 120 metre 510884.54
Cost of 1 metre 4257.37
Say 4257.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2153
26.73.2 Extra for using M-50 (Cement content 425 kg) instead of M-40
26.73.2.1 100mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 10.80 cum (120 Rmt )
120 Rmt X 1.20 m X .10 (25 % hollow)
Cement for M-50 Mix = 4.590 T
Cement for M-40 Mix = 4.320 T
Difference 0.270 T
0367 Portland Cement tonne 0.270 5000.00 1350.00
2209 Carriage of cement tonne 0.270 145.72 39.34
Plasticizer for M-50 Mix = 91.800 Kgs
Plasticizer for M-40 Mix = 86.400 Kgs
Difference 5.400 Kgs
7318 Plasticizer or Super Plasticizer 2% of
cement content kg 5.400 29.00 156.60
TOTAL 1545.94 W
Add 1 % Water charges on "W" 15.46
TOTAL 1561.40 X
Add GST on "X-A" (multiplying
factor 0.1405) 219.38
TOTAL 1780.78 Y
Add 15% CPOH on "Y" 267.12
TOTAL 2047.90 Z
Add Cess @ 1% on "Z" 20.48
Cost for 120 metre 2068.38
Cost of 1 metre 17.24
Say 17.25
26.73.2.2 120mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 12.96 cum (120 Rmt )
120 Rmt X 1.20 m X .12 (25 % hollow)
Cement for M-50 Mix = 5.508 T
Cement for M-40 Mix = 5.184 T
Difference 0.324 T
0367 Portland Cement tonne 0.324 5000.00 1620.00
2209 Carriage of cement tonne 0.324 145.72 47.21
Plasticizer for M-50 Mix = 110.160 Kgs
Plasticizer for M-40 Mix = 103.680 Kgs
Difference 6.480 Kgs
7318 Plasticizer or Super Plasticizer 2% of
cement content kg 6.48 29.00 187.92
TOTAL 1855.13 W
Add 1 % Water charges on "W" 18.55
TOTAL 1873.68 X
Add GST on "X" (multiplying
factor 0.1405) 263.25
TOTAL 2136.94 Y
Add 15% CPOH on "Y" 320.54
TOTAL 2457.48 Z
Add Cess @ 1% on "Z" 24.57
Cost for 120 metre 2482.05
Cost of 1 metre 20.68
Say 20.70
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2154
26.73.2.3 150mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 16.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.15 (25 % hollow)
Cement for M-50 Mix = 6.885 T
Cement for M-40 Mix = 6.480 T
Difference 0.405 T
0367 Portland Cement tonne 0.405 5000.00 2025.00
2209 Carriage of cement tonne 0.405 145.72 59.02
Plasticizer for M-50 Mix = 137.700 Kgs
Plasticizer for M-40 Mix = 129.600 Kgs
Difference 8.100 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 8.10 29.00 234.90
TOTAL 2318.92 W
Add 1 % Water charges on "W" 23.19
TOTAL 2342.11 X
Add GST on "X" (multiplying
factor 0.1405) 329.07
TOTAL 2671.17 Y
Add 15% CPOH on "Y" 400.68
TOTAL 3071.85 Z
Add Cess @ 1% on "Z" 30.72
Cost for 120 metre 3102.57
Cost of 1 metre 25.85
Say 25.85
26.73.2.4 200mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 20.160 cum (120 Rmt )
120 Rmt X 1.20 m X0.20 (30 % hollow)
Cement for M-50 Mix = 8.568 T
Cement for M-40 Mix = 8.064 T
Difference 0.504 T
0367 Portland Cement tonne 0.504 5000.00 2520.00
2209 Carriage of cement tonne 0.504 145.72 73.44
Plasticizer for M-50 Mix = 171.360 Kgs
Plasticizer for M-40 Mix = 161.280 Kgs
Difference 10.080 Kgs
7318 Plasticizer or Super Plasticizer 2% of
cement content kg 10.08 29.00 292.32
TOTAL 2885.76 W
Add 1 % Water charges on "W" 28.86
TOTAL 2914.62 X
Add GST on "X" (multiplying
factor 0.1405) 409.50
TOTAL 3324.12 Y
Add 15% CPOH on "Y" 498.62
TOTAL 3822.74 Z
Add Cess @ 1% on "Z" 38.23
Cost for 120 metre 3860.97
Cost of 1 metre 32.17
Say 32.15
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2155
26.73.2.5 250mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 25.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.25 (30 % hollow)
Cement for M-50 Mix = 10.710 T
Cement for M-40 Mix = 10.080 T
Difference 0.630 T
0367 Portland Cement tonne 0.63 5000.00 3150.00
2209 Carriage of cement tonne 0.63 145.72 91.80
Plasticizer for M-50 Mix = 214.200 Kgs
Plasticizer for M-40 Mix = 201.600 Kgs
Difference 12.600 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 12.60 29.00 365.40
TOTAL 3607.20 W
Add 1 % Water charges on "W" 36.07
TOTAL 3643.28 X
Add GST on "X" (multiplying
factor 0.1405) 511.88
TOTAL 4155.16 Y
Add 15% CPOH on "Y" 623.27
TOTAL 4778.43 Z
Add Cess @ 1% on "Z" 47.78
Cost for 120 metre 4826.21
Cost of 1 metre 40.22
Say 40.20
26.73.2.6 300mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 30.24 cum (120 Rmt )
120 Rmt X 1.20 m X 0.30 (30 % hollow)
Cement for M-50 Mix = 12.852 T
Cement for M-40 Mix = 12.096 T
Difference 0.756 T
0367 Portland Cement tonne 0.756 5000.00 3780.00
2209 Carriage of cement tonne 0.756 145.72 110.16
Plasticizer for M-50 Mix = 257.040 Kgs
Plasticizer for M-40 Mix = 241.920 Kgs
Difference 15.1200 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 15.12 29.00 438.48
TOTAL 4328.64 W
Add 1 % Water charges on "W" 43.29
TOTAL 4371.93 X
Add GST on "X" (multiplying
factor 0.1405) 614.26
TOTAL 4986.19 Y
Add 15% CPOH on "Y" 747.93
TOTAL 5734.12 Z
Add Cess @ 1% on "Z" 57.34
Cost for 120 metre 5791.46
Cost of 1 metre 48.26
Say 48.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2156
26.73.2.7 350mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 35.28 cum (120 Rmt )
120 Rmt X 1.20 m X 0.35 (30 % hollow)
Cement for M-50 Mix = 14.994 T
Cement for M-40 Mix = 14.112 T
Difference 0.882 T
0367 Portland Cement tonne 0.882 5000.00 4410.00
2209 Carriage of cement tonne 0.882 145.72 128.53
Plasticizer for M-50 Mix = 299.880 Kgs
Plasticizer for M-40 Mix = 282.240 Kgs
Difference 17.640 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 17.64 29.00 511.56
TOTAL 5050.09 W
Add 1 % Water charges on "W" 50.50
TOTAL 5100.59 X
Add GST on "X" (multiplying
factor 0.1405) 716.63
TOTAL 5817.22 Y
Add 15% CPOH on "Y" 872.58
TOTAL 6689.80 Z
Add Cess @ 1% on "Z" 66.90
Cost for 120 metre 6756.70
Cost of 1 metre 56.31
Say 56.30
26.73.2.8 400mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 40.32 cum (120 Rmt )
120 Rmt X 1.20 m X 0.40 (30 % hollow)
Cement for M-50 Mix = 17.136 T
Cement for M-40 Mix = 16.128 T
Difference 1.008 T
0367 Portland Cement tonne 1.008 5000.00 5040.00
2209 Carriage of cement tonne 1.008 145.72 146.89
Plasticizer for M-50 Mix = 342.720 Kgs
Plasticizer for M-40 Mix = 322.560 Kgs
Difference 20.160 Kgs
7318 Plasticizer or Super Plasticizer 2% of
cement content kg 20.16 29.00 584.64
TOTAL 5771.53 W
Add 1 % Water charges on "W" 57.72
TOTAL 5829.24 X
Add GST on "X" (multiplying
factor 0.1405) 819.01
TOTAL 6648.25 Y
Add 15% CPOH on "Y" 997.24
TOTAL 7645.49 Z
Add Cess @ 1% on "Z" 76.45
Cost for 120 metre 7721.94
Cost of 1 metre 64.35
Say 64.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2157
26.73.3 Extra for using M-60 (Cement content 440 kg) instead of M-40
26.73.3.1 100mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 10.80 cum (120 Rmt )
120 Rmt X 1.20 m X .10 (25 % hollow)
Cement for M-60 Mix = 4.752 T
Cement for M-40 Mix = 4.320 T
Difference 0.432 T
0367 Portland Cement tonne 0.432 5000.00 2160.00
2209 Carriage of cement tonne 0.432 145.72 62.95
Plasticizer for M-60 Mix = 95.040 Kgs
Plasticizer for M-40 Mix = 86.400 Kgs
Difference 8.640 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 8.640 29.00 250.56
TOTAL 2473.51 W
Add 1 % Water charges on "W" 24.74
TOTAL 2498.25 X
Add GST on "X" (multiplying
factor 0.1405) 351.00
TOTAL 2849.25 Y
Add 15% CPOH on "Y" 427.39
TOTAL 3276.64 Z
Add Cess @ 1% on "Z" 32.77
Cost for 120 metre 3309.40
Cost of 1 metre 27.58
Say 27.60
26.73.3.2 120mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 12.96 cum (120 Rmt )
120 Rmt X 1.20 m X .12 (25 % hollow)
Cement for M-60 Mix = 5.702 T
Cement for M-40 Mix = 5.184 T
Difference 0.518 T
0367 Portland Cement tonne 0.518 5000.00 2590.00
2209 Carriage of cement tonne 0.518 145.72 75.48
Plasticizer for M-60 Mix = 114.04 Kgs
Plasticizer for M-40 Mix = 103.680 Kgs
Difference 10.36 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 10.36 29.00 300.44
TOTAL 2965.92 W
Add 1 % Water charges on “W” 29.66
TOTAL 2995.58 X
Add GST on “X” (multiplying
factor 0.1405) 420.88
TOTAL 3416.46 Y
Add 15% CPOH on “Y” 512.47
TOTAL 3928.93 Z
Add Cess @ 1% on “Z” 39.29
Cost for 120 metre 3968.22
Cost of 1 metre 33.07
Say 33.05
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2158
26.73.3.3 150mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 16.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.15 (25 % hollow)
Cement for M-60 Mix = 7.128 T
Cement for M-40 Mix = 6.480 T
Difference 0.648 T
0367 Portland Cement tonne 0.648 5000.00 3240.00
2209 Carriage of cement tonne 0.648 145.72 94.43
Plasticizer for M-60 Mix = 142.56 Kgs
Plasticizer for M-40 Mix = 129.600 Kgs
Difference 12.960 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 12.96 29.00 375.84
TOTAL 3710.27 W
Add 1 % Water charges on "W" 37.10
TOTAL 3747.37 X
Add GST on "X" (multiplying
factor 0.1405) 526.51
TOTAL 4273.87 Y
Add 15% CPOH on "Y" 641.08
TOTAL 4914.96 Z
Add Cess @ 1% on "Z" 49.15
Cost for 120 metre 4964.11
Cost of 1 metre 41.37
Say 41.35
26.73.3.4 200mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 20.160 cum (120 Rmt )
120 Rmt X 1.20 m X0.20 (30 % hollow)
Cement for M-60 Mix = 8.870 T
Cement for M-40 Mix = 8.064 T
Difference 0.806 T
0367 Portland Cement tonne 0.806 5000.00 4030.00
2209 Carriage of cement tonne 0.806 145.72 117.45
Plasticizer for M-60 Mix = 177.40 Kgs
Plasticizer for M-40 Mix = 161.280 Kgs
Difference 16.12 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 16.12 29.00 467.48
TOTAL 4614.93 W
Add 1 % Water charges on "W" 46.15
TOTAL 4661.08 X
Add GST on "X" (multiplying
factor 0.1405) 654.88
TOTAL 5315.96 Y
Add 15% CPOH on "Y" 797.39
TOTAL 6113.36 Z
Add Cess @ 1% on "Z" 61.13
Cost for 120 metre 6174.49
Cost of 1 metre 51.45
Say 51.45
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2159
26.73.3.5 250mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 25.20 cum (120 Rmt )
120 Rmt X 1.20 m X 0.25 (30 % hollow)
Cement for M-60 Mix = 11.088 T
Cement for M-40 Mix = 10.080 T
Difference 1.008 T
0367 Portland Cement tonne 1.008 5000.00 5040.00
2209 Carriage of cement tonne 1.008 145.72 146.89
Plasticizer for M-60 Mix = 221.760 Kgs
Plasticizer for M-40 Mix = 201.600 Kgs
Difference 20.160 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 20.16 29.00 584.64
TOTAL 5771.53 W
Add 1 % Water charges on "W" 57.72
TOTAL 5829.24 X
Add GST on "X" (multiplying
factor 0.1405) 819.01
TOTAL 6648.25 Y
Add 15% CPOH on "Y" 997.24
TOTAL 7645.49 Z
Add Cess @ 1% on "Z" 76.45
Cost for 120 metre 7721.94
Cost of 1 metre 64.35
Say 64.35
26.73.3.6 300mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 30.24 cum (120 Rmt )
120 Rmt X 1.20 m X 0.30 (30 % hollow)
Cement for M-60 Mix = 13.306 T
Cement for M-40 Mix = 12.096 T
Difference 1.210 T
0367 Portland Cement tonne 1.21 5000.00 6050.00
2209 Carriage of cement tonne 1.21 145.72 176.32
Plasticizer for M-60 Mix = 266.12 Kgs
Plasticizer for M-40 Mix = 241.920 Kgs
Difference 24.20 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 24.20 29.00 701.80
TOTAL 6928.12 W
Add 1 % Water charges on "W" 69.28
TOTAL 6997.40 X
Add GST on "X" (multiplying
factor 0.1405) 983.14
TOTAL 7980.54 Y
Add 15% CPOH on "Y" 1197.08
TOTAL 9177.62 Z
Add Cess @ 1% on "Z" 91.78
Cost for 120 metre 9269.39
Cost of 1 metre 77.24
Say 77.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2160
26.73.3.7 350mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 35.28 cum (120 Rmt )
120 Rmt X 1.20 m X 0.35 (30 % hollow)
Cement for M-60 Mix = 15.523 T
Cement for M-40 Mix = 14.112 T
Difference 1.411 T
0367 Portland Cement tonne 1.411 5000.00 7055.00
2209 Carriage of cement tonne 1.411 145.72 205.61
Plasticizer for M-60 Mix = 310.46 Kgs
Plasticizer for M-40 Mix = 282.240 Kgs
Difference 28.22 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 27.22 29.00 789.38
TOTAL 8049.99 W
Add 1 % Water charges on "W" 80.50
TOTAL 8130.49 X
Add GST on "X" (multiplying
factor 0.1405) 1142.33
TOTAL 9272.82 Y
Add 15% CPOH on "Y" 1390.92
TOTAL 10663.75 Z
Add Cess @ 1% on "Z" 106.64
Cost for 120 metre 10770.39
Cost of 1 metre 89.75
Say 89.75
26.73.3.8 400mm thick hollow core slab
Code Description Unit Quantity Rate Amount
Detail cost of 40.32 cum (120 Rmt )
120 Rmt X 1.20 m X 0.40 (30 % hollow)
Cement for M-60 Mix = 17.741 T
Cement for M-40 Mix = 16.128 T
Difference 1.613 T
0367 Portland Cement tonne 1.613 5000.00 8065.00
2209 Carriage of cement tonne 1.613 145.72 235.05
Plasticizer for M-60 Mix = 352.82 Kgs
Plasticizer for M-40 Mix = 322.560 Kgs
Difference 32.26 Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 32.26 29.00 935.54
TOTAL 9235.59 W
Add 1 % Water charges on "W" 92.36
TOTAL 9327.94 X
Add GST on "X" (multiplying
factor 0.1405) 1310.58
TOTAL 10638.52 Y
Add 15% CPOH on "Y" 1595.78
TOTAL 12234.30 Z
Add Cess @ 1% on "Z" 122.34
Cost for 120 metre 12356.64
Cost of 1 metre 102.97
Say 102.95
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2161
26.74 Fabrication and manufacturing of solid precast concrete element with
provisions of shear keys, connecting loops, dowel tubes and proper lifting
accessories for walls, beams, slabs, stairs, column etc, of various thickness,
shape and size of different concrete grades manufactured in controlled factory
environment with approved methodology including moulds (Pallet system,
Tilts form, table moulds, battery moulds, vertical moulds, beam moulds,
column moulds, staircase moulds, Facade mould, etc.), mixing, transporting
and placing of concrete, vibrating, curing, finishing, making necessary cutout/
holes of required sizes for services, yard handling & stacking all complete as
per IS 11447:1985 and as per approved shop drawings and design mix as per
the direction of Engineer-in-Charge (Cost of reinforcement, Mechanical,
Electrical and Plumbing inserts will be paid separately).
Note: Excess/less cement over the specified cement content used as per design
mix is payable/recoverable separately)
26.74.1 Concrete grade M-35 (Cement content 370 kgs)
Code Description Unit Quantity Rate Amount
Detail of cost for 1.26 Cum Considers
a wall 2.80 X 3.00 X 0.15 = 1.260 Cum
5.33.2.3 Rate as per item no 5.33.2.3 of SH RCC cum 1.26 10,363.30 13057.76 A
5.35 Rate as per item no 5.35 of
SH RCC (M-35 (370 kgs)) quintal 0.252 688.45 173.49 A
9999 Cost of hosting and fixing moulds L.S 372.00 2.12 788.64
5.9.1 Rate as per item 5.9.1 of SH RCC,
Side Shuttering of walls
((2.8+3)x2x0.15=1.74) sqm 1.74 307.95 535.83 A
9999 Table buffing & oiling L.S 174.00 2.12 368.88
9999 Sundries (Extra labour for Lifting,
transportation, stacking of finished
precast elements) L.S 230.00 2.12 487.60
5.41.1 Rate as per item no 5.41.1 of SH RCC
(Curing using curing compound) sqm 18.54 57.50 1066.05 A
7929 Shear loops (6mm dia GI wire rope)
(For vertical joints) 6 nos on each side each 12.00 210.00 2520.00
7930 dowel tubes (Corrugated GI pipes 50 to
80mm dia) (For horizontal joints) metre 3.00 144.00 432.00
9999 Shear key (6mm thick mechanically
folded MS plate) L.S 115.00 2.12 243.80
7931 Hooks for lifting (Alloy steel) having
2.5 tonne capacity each 2.00 270.00 540.00
Labour for fixing accessories & inserts
such as shear loops, shear keys,
dowel tubes, lifting hooks
0155 Mason (Average) day 0.50 749.00 374.50
0115 Coolie day 0.50 645.00 322.50
Labour for operating of hoisting &
fixing moulds
0157 Operator day 0.50 784.00 392.00
0116 Fitter (Grade 1) day 0.30 784.00 235.20
0115 Coolie day 0.30 645.00 193.50
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2162
Code Description Unit Quantity Rate Amount
9999 Sundries (Labour cost such as crane,
trailer(flat bed & a frames) & panel
racks for stacking of precost concrete
panel wall) L.S 173.41 2.12 367.63
TOTAL 22099.38 W
Add 1 % Water charges on "W-A" 72.66
TOTAL 22172.04 X
Add GST on "X-A" (multiplying
factor 0.1405) 1031.12
TOTAL 23203.16 Y
Add 15% CPOH on "Y-A" 1255.50
TOTAL 24458.66 Z
Add Cess @ 1% on "Z-A" 96.26
Cost for 1.26 Cum 24554.92
Cost of 1 Cum 19488.03
Say 19488.05
26.74.2 Extra for using M-40 (Cement content 400 kg) instead of M-35
Code Description Unit Quantity Rate Amount
Cement for M-35 Mix = 0.370 T
Cement for M-40 Mix = 0.400 T
Difference 0.030 T
0367 Portland Cement tonne 0.03 5000.00 150.00
2209 Carriage of cement tonne 0.03 145.72 4.37
Plasticizer for M-35 Mix =7.400 Kgs
Plasticizer for M-40 Mix = 8.000 Kgs
Difference 0.600Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 0.60 29.00 17.40
TOTAL 171.77 W
Add 1 % Water charges on "W" 1.72
TOTAL 173.49 X
Add GST on "X" (multiplying
factor 0.1405) 24.38
TOTAL 197.86 Y
Add 15% CPOH on "Y" 29.68
TOTAL 227.54 Z
Add Cess @ 1% on "Z" 2.28
Cost of 1.00 Cum 229.82
Say 229.80
26.74.3 Extra for using M-50 (Cement content 425 kg) instead of M-35
Code Description Unit Quantity Rate Amount
Cement for M-35 Mix = 0.370 T
Cement for M-50 Mix = 0.425 T
Difference 0.055 T
0367 Portland Cement tonne 0.055 5000.00 275.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2163
Code Description Unit Quantity Rate Amount
2209 Carriage of cement tonne 0.055 145.72 8.01
Plasticizer for M-35 Mix =7.400 Kgs
Plasticizer for M-50 Mix = 8.500 Kgs
Difference 1.100Kgs
7318 Plasticizer or Super Plasticizer 2% of
cement content kg 1.10 29.00 31.90
TOTAL 314.91 W
Add 1 % Water charges on "W" 3.15
TOTAL 318.06 X
Add GST on "X" (multiplying
factor 0.1405) 44.69
TOTAL 362.75 Y
Add 15% CPOH on "Y" 54.41
TOTAL 417.16 Z
Add Cess @ 1% on "Z" 4.17
Cost of 1.00 Cum 421.34
Say 421.35
26.74.4 Extra for using M-60 (Cement content 440 kg) instead of M-35
Code Description Unit Quantity Rate Amount
Cement for M-35 Mix = 0.370 T
Cement for M-60 Mix = 0.440 T
Difference 0.070 T
0367 Portland Cement tonne 0.07 5000.00 350.00
2209 Carriage of cement tonne 0.07 145.72 10.20
Plasticizer for M-35 Mix =7.400 Kgs
Plasticizer for M-60 Mix = 8.800 Kgs
Difference 1.400Kgs
7318 Plasticizer or Super Plasticizer 2%
of cement content kg 1.40 29.00 40.60
TOTAL 400.80 W
Add 1 % Water charges on "W" 4.01
TOTAL 404.81 X
Add GST on "X" (multiplying
factor 0.1405) 56.88
TOTAL 461.68 Y
Add 15% CPOH on "Y" 69.25
TOTAL 530.94 Z
Add Cess @ 1% on "Z" 5.31
Cost of 1.00 Cum 536.25
Say 536.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2164
26.75 Providing & laying in position Prestressing steel strands (low relaxation) on
hollow core bed by using mechanical pulling arrangement like Rabbit/ Bed
master including all accessories for Stressing & destressing operations as
per approved make conforming to IS1343 & grade FY-1860 etc, complete as
per drawings and direction of Engineer -in-charge.
Code Description Unit Quantity Rate Amount
Considering Four beds
8 strands (each strand is of 9.53mm
dia consisting of 7 wires) X 4 beds X
120 Rmt X 0.453 Unit wt = 1739.52
kgs. Say 1740kgs.
Details of Cost for 1740 Kg
MATERIALS
Quantity = 17.40 quintal + Add
wastage 10 % = 1.74 q.
Total = 19.14 q
0993 FY-1860 grade wire strands quintal 19.14 5700.00 109098.00
2205 Carriage of material tonne 1.914 145.72 278.91
Cutting baldes required for strand cutting
9999 Strand cutting by cutting saw machine L.S. 555.00 2.12 1176.60
Wedges
9999 Cost of wedge L.S. 617.00 2.12 1308.04
Resources - For laying and fixing
cables, anchorages
0128 Mate day 1.00 714.00 714.00
0102 Blacksmith 1st class day 4.00 784.00 3136.00
0115 Coolie day 3.00 645.00 1935.00
Labour- For prestressting
0128 Mate day 2.00 714.00 1428.00
0116 Fitter (Grade-1) day 3.00 784.00 2352.00
0157 Operators day 2.00 784.00 1568.00
0115 Coolie day 2.00 645.00 1290.00
MACHINERY “(12 HRS Required to
Lay 1.914 Ton strands on 4 beds)
0032 Stressing Machine (jack with pump) day 1.50 11500.00 17250.00
0028 Hire & Running Charges of Crane 20
Ton Capacity to handle strands (8 Nos.
strand coils ( averege weight 3Ton
each) required to lay one bed of 8
strands as one coil can lay only one
strand at a time. Therefore to operate
one complete bed total 8 Nos strand
coils required, hence total 3X8= 24 Ton
weight will be handled for one bed) day 1.50 7000.00 10500.00
0034 Cutting Saw Machine day 1.50 1350.00 2025.00
0030 Hire charges of Generator 250 KVA day 1.50 3000.00 4500.00
0035 Strands Roller machinery for laying
strands day 1.50 3500.00 5250.00
0036 Bed master (Pulling strands) day 1.50 3000.00 4500.00
0028 Crane handling charges for bed master
& stressing machine. One bed master
approx wt = 03 Ton (to be placed on
each bed with the help of crane for
laying of strands ) One stressing
Machine approx wt = 2.5 Ton (to be
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2165
Code Description Unit Quantity Rate Amount
placed on each active ends of bed with
the help of crane for initial pulling &
stressing of strands ). Handling &
Shifting of bed master & stressing
machine has to be done for each bed
separately. day 1.50 7000.00 10500.00
1235 Diesel for generator set (14 litres per
hour for 11 hours) Litre 154.00 80.87 12453.98
TOTAL 191263.53 W
Add 1 % Water charges on "W" 1912.64
TOTAL 193176.16 X
Add GST on "X" (multiplying
factor 0.1405) 27141.25
TOTAL 220317.41 Y
Add 15% CPOH on "Y" 33047.61
TOTAL 253365.03 Z
Add Cess @ 1% on "Z" 2533.65
Cost for 1740 kgs 255898.68
Cost of 1 Kg 147.07
Say 147.05
26.76 Transportation of Precast Elements by flat bed Trailor (Double / Triple axle
40ft Length with proper accessories like A frame etc) from factory, including
the cost of loading, unloading & stacking at site with the help of required
capacity cranes.
26.76.1 Lead within 15km
Code Description Unit Quantity Rate Amount
Trailors having capcity 22MT
Hire charges of truck trailors
Number of trips in working day of
8 hours
N=8/{(2L/S)+2)}. Where L=Lead in Km.,
S=Speed in Km.per hour, 1 hour is
allowed for loading & 1 hour for
unloading.
L= 15 km.
S= 15 km / hr
N=8/{(30/15)+2)}=02 Trips / day
9999 Charges of Trailors having capcity
22MT including cost of fuel & driver
cost and maintenance L.S. 1738.00 2.12 3,684.56
0028 Hire charges of Crane capacity of
30MT for loading from stock yard and
unloading at site for 120 MT. day 0.3667 7000.00 2,566.90
0128 Mate day 0.50 714.00 357.00
0114 Beldar day 0.50 645.00 322.50
9999 wooden battens for tranporatation L.S. 57.80 2.12 122.54
9999 Chain for packing & binding precast
elements L.S. 57.80 2.12 122.54
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2166
Code Description Unit Quantity Rate Amount
9999 sundries L.S. 220.00 2.12 466.40
TOTAL 7642.43 W
Add 1 % Water charges on "W" 76.42
TOTAL 7718.86 X
Add GST on "X" (multiplying
factor 0.1405) 1084.50
TOTAL 8803.36 Y
Add 15% CPOH on "Y" 1320.50
TOTAL 10123.86 Z
Add Cess @ 1% on "Z" 101.24
Cost for 22 MT 10225.10
Cost of 1 MT 464.78
Say 464.80
26.76.2 Add/Deduct over item 26.76.1 for every additional lead of 5 km
Code Description Unit Quantity Rate Amount
Extra for lead 5 km
9999 Charges of Trailors having capcity
22MT including cost of fuel & driver
and maintenance L.S. 579.00 2.12 1227.48
9999 sundries L.S. 220.00 2.12 466.40
TOTAL 1693.88 W
Add 1 % Water charges on "W" 16.94
TOTAL 1710.82 X
Add GST on "X" (multiplying
factor 0.1405) 240.37
TOTAL 1951.19 Y
Add 15% CPOH on "Y" 292.68
TOTAL 2243.87 Z
Add Cess @ 1% on "Z" 22.44
Cost for 22 MT 2266.31
Cost of 1 MT 103.01
Say 103.00
26.77 Erection & Installation of Precast/Prestressed Concrete elements in correct
& final position with proper line level and plumb at site making all
arrangements (i.e cranes, push-pull jacks & all another T & P for lifting Placing
& Alignment of elements, within erection tolerance as per IS 15916 as per
approved shop drawings and all complete as per the direction of Engineer-
in-Charge but excluding the cost of sim pads, non shrink grout and steel
works i.e hangers. All work up to fifth floor.
26.77.1 Prestressed hollow core Slab up to 200 mm thickness
Code Description Unit Quantity Rate Amount
Detail of cost for 150 Sqm.
Length of element can be upto
8.00 metres.
Mobile crane (Tyre mounted) upto
25m height 100 feet boom
0044 Cost for crane upto 40 tonne capacity day 1.00 8000.00 8000.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2167
Code Description Unit Quantity Rate Amount
9999 Hire charges of props & Misc L.S. 434.00 2.12 920.08
0070 Genrator hiring 100kva hour 8.00 300.00 2400.00
Labour cost for erection
0111 Carpenter 1st class day 1.00 784.00 784.00
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0130 Mistry day 2.00 784.00 1568.00
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries (Miscellaneous tools and
lifting slings) L.S. 500.00 2.12 1060.00
TOTAL 19018.08 W
Add 1 % Water charges on "W" 190.18
TOTAL 19208.26 X
Add GST on "X" (multiplying
factor 0.1405) 2698.76
TOTAL 21907.02 Y
Add 15% CPOH on "Y" 3286.05
TOTAL 25193.07 Z
Add Cess @ 1% on "Z" 251.93
Cost for 150 Sqm 25445.01
Cost of 1 Sqm 169.63
Say 169.65
26.77.2 Prestressed hollow core slab above 200 mm up to 400 mm thickness
Code Description Unit Quantity Rate Amount
Detail of cost for 120 Sqm.
Length of element can be more than
8.00 metre and upto 14.00 metres.
0067 Cost for crane upto 80 tonne capacity day 1.00 15000.00 15000.00
9999 Hire charges of props & Misc L.S. 347.00 2.12 735.64
0070 Genrator hiring 100kva hour 8.00 300.00 2400.00
Labour cost for erection
0111 Carpenter 1st class day 1.00 784.00 784.00
0112 Carpenter 2nd class day 2.00 714.00 1428.00
0116 Fitter (grade 1) day 2.00 784.00 1568.00
0130 Mistry day 2.00 784.00 1568.00
0114 Beldar day 2.00 645.00 1290.00
9999 Sundries (Miscellaneous tools and
lifting slings) L.S. 500.00 2.12 1060.00
TOTAL 25833.64 W
Add 1 % Water charges on "W" 258.34
TOTAL 26091.98 X
Add GST on "X" (multiplying
factor 0.1405) 3665.92
TOTAL 29757.90 Y
Add 15% CPOH on "Y" 4463.68
TOTAL 34221.58 Z
Add Cess @ 1% on "Z" 342.22
Cost for 120 Sqm 34563.80
Cost of 1 Sqm 288.03
Say 288.05
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2168
26.77.3 Solid concrete wall elements
Code Description Unit Quantity Rate Amount
Detail of cost for 18 Cum. / Day
Considering volume of different type of
elements
wall elements = 15 cum (13 nos)
Beams / portal = 3 cum (02 nos)
Total no of elements = 15 nos
0072 Cost for crane (50 MT) duration 01 day day 1.00 8500.00 8500.00
9999 Shifting of elements L.S. 434.00 2.12 920.08
9999 Hire charges of props & Misc for
3 days (3x3 = 9 / pc) L.S. 780.00 2.12 1653.60
1027 Erection Bolts ( Minimum 04 nos for
each element) each 60.00 25.00 1500.00
0070 Genrator hiring 100kva hour 8.00 300.00 2400.00
Labour cost
0111 Carpenter 1st class day 2.00 784.00 1568
0112 Carpenter 2nd class day 2.00 714.00 1428
0116 Fitter (grade 1) day 2.00 784.00 1568
0130 Mistry day 3.00 784.00 2352
0116 Fitter (grade 1) day 2.00 784.00 1568
0114 Beldar day 8.00 645.00 5160
9999 Scaffolding, hire charge of drill
machine etc. L.S. 500.00 2.12 1060
9999 Sundries (Miscellaneous tools
and lifting slings) L.S. 500.00 2.12 1060
TOTAL 30737.68 W
Add 1 % Water charges on "W" 307.38
TOTAL 31045.06 X
Add GST on "X" (multiplying
factor 0.1405) 4361.83
TOTAL 35406.89 Y
Add 15% CPOH on "Y" 5311.03
TOTAL 40717.92 Z
Add Cess @ 1% on "Z" 407.18
Cost for 18 cum 41125.10
Cost of 1 cum 2284.73
Say 2284.75
26.78 Providing & Applying weather proof sealant on outer joints of approved make
confirming to IS & directed by Engineer-in-charge.
26.78.1 Sealant 25mmx10mm at joints
Code Description Unit Quantity Rate Amount
Detail of material required for =
1.00 metre including 5 % wastage
8646 Silicon sealant (including 5% wastage) cartridge 0.87 112.00 97.44
8654 Masking tape metre 2.00 2.18 4.36
9999 Scaffolding, hire charge etc. L.S. 2.87 2.12 6.08
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2169
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 2.87 2.12 6.08
TOTAL 113.97 W
Add 1 % Water charges on "W" 1.14
TOTAL 115.11 X
Add GST on "X" (multiplying
factor 0.1405) 16.17
TOTAL 131.28 Y
Add 15% CPOH on "Y" 19.69
TOTAL 150.97 Z
Add Cess @ 1% on "Z" 1.51
Cost of 1 metre 152.48
Say 152.50
26.79 Providing & Laying of levelling sim pads required sizes (5x5cm to 10x10cm)
of PVC / Rubber to adjust level of bearing surface of supporting members as
per the direction of Engineer in charge.
26.79.1 2mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 100 nos
MATERIAL
0246 2 mm thick sim pad each 100.00 10.00 1000.00
9977 Carriage of material L.S. 5.00 2.12 10.60
LABOUR
0116 Fitter (Grade-1) day 1.00 784.00 784.00
9999 Sundries L.S. 10.00 2.12 21.20
TOTAL 1815.80 W
Add 1 % Water charges on "W" 18.16
TOTAL 1833.96 X
Add GST on "X" (multiplying
factor 0.1405) 257.67
TOTAL 2091.63 Y
Add 15% CPOH on "Y" 313.74
TOTAL 2405.37 Z
Add Cess @ 1% on "Z" 24.05
Cost for100 Nos 2429.43
Cost of each 24.29
Say 24.30
26.79.2 5 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 100 nos
MATERIAL
0247 5 mm thick sim pad each 100.00 15.00 1500.00
9977 Carriage of material L.S. 5.00 2.12 10.60
LABOUR
0116 Fitter (Grade-1) day 1.00 784.00 784.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2170
Code Description Unit Quantity Rate Amount
9999 Sundries L.S. 10.00 2.12 21.20
TOTAL 2315.80 W
Add 1 % Water charges on “W” 23.16
TOTAL 2338.96 X
Add GST on “X” (multiplying
factor 0.1405) 328.62
TOTAL 2667.58 Y
Add 15% CPOH on “Y” 400.14
TOTAL 3067.72 Z
Add Cess @ 1% on “Z” 30.68
Cost for100 Nos 3098.40
Cost of each 30.98
Say 31.00
26.79.3 10 mm thick
Code Description Unit Quantity Rate Amount
Detail of cost for 100 nos
MATERIAL
0248 10 mm thick sim pad each 100.00 25.00 2500.00
9977 Carriage of material L.S 5.00 2.12 10.60
LABOUR
0116 Fitter (Grade-1) day 1.00 784.00 784.00
9999 Sundries LS 10.00 2.12 21.20
TOTAL 3315.80 W
Add 1 % Water charges on "W" 33.16
TOTAL 3348.96 X
Add GST on "X" (multiplying
factor 0.1405) 470.53
TOTAL 3819.49 Y
Add 15% CPOH on "Y" 572.92
TOTAL 4392.41 Z
Add Cess @ 1% on "Z" 43.92
Cost for100 Nos 4436.33
Cost of each 44.36
Say 44.35
26.80 Providing & Grouting of dowel tubes / Shear keys / Joints of precast members
with M-60 grade cementitious grout (Non Shrink) of approved make by suitable
means ( Free flowing /pump),curing etc. Complete as per directions of
Engineer-in-charge. (The payment shall be made on the basis of actual weight
of approved grout injected.)
26.80.1 Stirrer mixed cementitious grout (non shrink) of approved make in dowel
tubes / Shear keys / Joints of precast members.
Code Description Unit Quantity Rate Amount
Detail of cost for 250 kgs non shrink
cementitious grout
including 5 % wastage
1251 M-60 grade cemetitious grout
(Non Shrink) kg 262.50 28.00 7350.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2171
Code Description Unit Quantity Rate Amount
2209 Carriage of cementitious material tonne 0.25 145.72 36.43
9999 Grouting charges of Stirrer mixed
cementitious grout, rubber, pipe and
other accessories hire charges of
plant, machinery including necessary
fuel and transportation of site L.S. 2250.00 2.12 4770.00
LABOUR
0122 Mason (for plaster of paris work)
1st class day 1.00 784.00 784.00
0155 Masson (Average) day 1.00 749.00 749.00
0161 Helper (Technician) day 1.00 645.00 645.00
TOTAL 14334.43 W
Add 1 % Water charges on "W" 143.34
TOTAL 14477.77 X
Add GST on "X" (multiplying
factor 0.1405) 2034.13
TOTAL 16511.90 Y
Add 15% CPOH on "Y" 2476.79
TOTAL 18988.69 Z
Add Cess @ 1% on "Z" 189.89
Cost for 250 Kgs 19178.57
Cost of 1 Kg 76.71
Say 76.70
26.81 Providing and fixing Scaffolding net of required width made of high density
Polyethylene UV stabilized knitted on warp knitting machines having density
100grams/sqm and shading coefficient minimum 75% around the construction
site/ for vertical extension as per requirement including fastening/tying with
building/scaffolding pipes or with any other fixtures etc. complete as per
direction of Engineer-in-Charge. (One time payment shall be made for
providing Scaffolding net from start of work till completion of work including
shifting if any. The Scaffolding net shall be the property of the contractor on
completion of the work)
Code Description Unit Quantity Rate Amount
Details of cost for 300 sqm.
MATERIALS:
8761 Scaffolding net sqm 300.00 22.00 6600.00 P
9999 Carriage L.S. 3.00 2.12 6.36
Less Salvage value taken 25% on (P) -1650.00
LABOUR:
0114 Beldar day 1.00 645.00 645.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2172
Code Description Unit Quantity Rate Amount
9999 Sundries for tying the net L.S. 10.00 2.12 21.20
Total 5622.56 W
Add 1% for water charges 56.23
Total 5678.79 X
Add GST on "X" (multiplying
factor 0.1405) 797.87
Total 6476.65 Y
Add CPOH @ 15% on "Y" 971.50
Total 7448.15 Z
Add Cess @ 1% on "Z" 74.48
Cost of 300 Sqm. 7522.63
Cost of 1 Sqm. 25.08
Say 25.10
26.82 Providing and laying rigid EPS (cellular plastic material) blocks conforming
to ASTM standards/specifications of minimum density 21.60 Kg/cum on floors,
steps, stage etc. of required size and shape as per direction of the Engineer-
in-Charge. This shall include the following operation.
The EPS blocks shall be cut to required shape and sizes including cuttings for
passing of services, joined together with synthetic resin adhesives as per
relevant specifications and packed/placed in position for stepped floor or platform
formation. The top and sides surfaces to be provided with GI woven wire mesh
of aperture 5.45 mm (with wire dia 0.90 mm) secured to EPS blocks with wire
pins/clips. Horizontal top surface to be provided with 20 mm thick cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate upto 6mm
chippings) and vertical surface to be provided with 12mm cement plaster 1:4 (1
cement : 4 coarse sand). The concrete/plastered surfaces so prepared shall be
scratched with wire brushes to form burrs, so as to act as base for flooring or
veneering/panelling to be done later as per approved design (which shall be
paid for separately complete as per direction of the Engineer-in-Charge.
Code Description Unit Quantity Rate Amount
Details of cost for a Lecture Hall of
area 8.40 x 16.00= 134.40 Sqm
Assuming stepped floor for a Lecture
Hall having 8 rows and each row by
100mm higher than the previous one.
(Assuming 8 rows 1.50 meter wide and
four columns also 1.5 meter wide with
1.2 meter wide passage between row 1
and 2, 3 and 4 and front lecturer
pedestrian.
Material
EPS blocks in sizes of =
1.20x1.20x0.10 m
8.40 m x 12 m x 0.45 m = 45.90 cum
8.40 m x 3 m x 0.15 m = 3.78 cum
49.68 cum Say = 50.00 cum
50 cum @ 21.60 Kg/cum. Total =
1080.00 kg
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2173
Code Description Unit Quantity Rate Amount
5744 EPS blocks kg 1080.00 150.00 162000.00
GI woven mesh of aperture 5.45 mm
(with wire of dia 0.90 mm = 134.40
sqm + 13.60 sqm = 150.00 sqm @
1.61 Kg/sqm. Total = 241.50 kgs
5745 GI woven mesh of aperture 5.45 mm
(with wire of dia 0.90 mm kg 241.50 60.00 14490.00
Total surface area to be joined 504
sqm considering 1/6th area for
adhesive i.e. 84 sqm @ 100 Gm/sqm.
Total = 8.50 kgs
5746 SR adhesive for joining EPS blocks kg 8.50 180.00 1530.00
9999 Wire pins/clips to secure IRC mesh to
EPS blocks L.S. 675.00 2.12 1431.00
9999 T&P sundries i/c cutting tools etc. L.S. 340.00 2.12 720.80
Labour:- For cutting arranging &
packing the EPS blocks in position
including jointing with SR adhesive and
making arranging/cutting for fixing of
services and fixing IRC welded mesh
to EPS blocks.
0156 Fitter/Carpenter (average) day 2.00 749.00 1498.00
0114 Beldar day 1.00 645.00 645.00
Cement concrete 1:2:4 (1 cement : 2
cement sand : 4 graded stone clippings
upto 6 mm size)
134.4x0.025 = 3.36 cum
4.1.3 Rate as per item no 4.1.3
SH:4 (Cement Concrete) cum 3.36 7365.15 24746.90 A
12mm cement plaster
1:4 (1 cement : 4 coarse sand)
13.4.1 Rate as per item no 13.4.1
SH:13 (Finishing) sqm 9.24 307.25 2838.99 A
0155 Mason (average) for making burrs day 1.00 749.00 749.00
Total 210649.69 W
Add 1 % Water charges on "W-A" 1830.64
TOTAL 212480.33 X
Add GST on "X-A" (multiplying
factor 0.1405) 25977.67
TOTAL 238458.00 Y
Add 15% CPOH on "Y-A" 31630.82
TOTAL 270088.82 Z
Add Cess @ 1% on "Z-A" 2425.03
Cost of 134.40 sqm 272513.85
Cost of 1 sqm 2027.63
Say 2027.65
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2174
26.83 Applying stamping finish to the top surface of freshly laid plain/reinforced
cement concrete of specified grade in porticos, sidewalks, driveways, pool
decks and open yards as per direction of the Engineer-in-Charge. The process
shall include the following:-
• The concrete shall be placed and screeded to the finished grade, and floated
to a uniform surface by using standard finishing techniques. The approved
color hardener @ 2.7 kg/sqm shall be applied evenly to the surface of the
fresh concrete by the dry shake method by sprinkling in two or more shakes,
floated after each shake and trowelled only after the final floating. The approved
release agent @ 0.113 kg/sqm shall be applied evenly to the trowelled surface
before stamping or the said release agent can be applied to the flexible
polyurethane stamp moulds of approved design and in required sizes to
achieve final stamped pattern. These stampings shall be placed on the surface
of concrete in three to four pieces at a time and tapped gently with rammers
of sufficient size & weight to leave proper stamp marks and the process
repeated for the remaining concrete surface till the whole surface to be
stamped is completed within the time while concrete is in plastic stage of
setting.
• After stamping, the curing shall be done as per manufactures
specifications. After initial curing the imprinted joints shall be grouted using
cement slurry mixed with color hardener as per the requirement. The surface
shall be sealed by applying acrylic based sealer not less than 0.167 litre/sqm.on
finished surface.
• The construction joints shall be provided by groove cutting of size 4mm x
20mm in panel size 3m x 3 m or lesser as per the site conditions and filling
the same with 10 mm baker rod and providing and laying (PU) Polyurethane
based joint sealer of approved make as per manufacturer’s specifications
and finished by applying Polyurethane resin based top protective clear coat
of minimum 80 micron applied with rollers on properly cured and dry clean
surface. (Cost of concrete for flooring is not included in this item which shall
be paid separately.)
Code Description Unit Quantity Rate Amount
Details of cost for 100 Sqm
Material
7224 Concrete hardener Kg 297.00 20.00 5940.00
7225 Release agent Litres 1.35 200.00 270.00
7226 Sealer Kg 17.50 260.00 4550.00
7227 PU resin top coat Kg 23.00 225.00 5175.00
9999 T&P like tollers of various sizes
dewatering machines i/c floaters and
suckers, brushes and water jet etc.
(rentals only) L.S. 6000.00 2.12 12720.00
Labour for spreading/sprinkling the floor
hardeners, floating, trowelling,
spreading the release agent, stamp
molds, tapping of molds into concrete
shifting of molds for repeat process,
grouting the joints and applying sealers
and finishing etc.
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2175
Code Description Unit Quantity Rate Amount
0169 Specialized technicians day 6.00 853.00 5118.00
0124 Assistant/Operators (Second Class
Mason) day 6.00 714.00 4284.00
0123 Mason 1st class for grouting repairs &
applying sealer etc. day 2.00 784.00 1568.00
0131 Painter day 1.00 714.00 714.00
0114 Helper/Beldar day 10.00 645.00 6450.00
9999 Sundries for grouts pigments etc. L.S. 500.00 2.12 1060.00
Total 47849.00 W
Add 1 % Water charges on "W" 478.49
TOTAL 48327.49 X
Add GST on "X" (multiplying
factor 0.1405) 6790.01
TOTAL 55117.50 Y
Add 15% CPOH on "Y" 8267.63
TOTAL 63385.13 Z
Add Cess @ 1% on "Z" 633.85
Cost of 100 sqm 64018.98
Cost of 1 sqm 640.19
Say 640.20
26.84 Supplying and laying of Uni-Axial Woven Polyster Geogrid conforming to
MORTH 3100 and IRC113, as soil reinforcement/basal reinforcement including
accessories like tie-strips, nuts & bolts and loops/lugs for joining reinforcing
elements with the facia pannels, overlaps and other protective elements for
synthetic geo-grids and all other activities required for reinforced soil walls,
slopes etc complete as per design requirements, manufacturer specifications
and as per direction of engineer-in- charge.
26.84.1 Uni Axial Woven polyster geogrid of minimum tensile strength 40KN/m in the
Longitudinal direction and 20 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8979 Uni Axial Woven polyster geogrid of
minimum tensile strength 40KN/m in
the Longitudinal direction and 20 KN/m
in the Transverse direction. sqm 300.00 139.00 41700.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the item
in all respect including transportation.
i.e 5% of (P) 2085.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2176
Code Description Unit Quantity Rate Amount
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 50054.04 W
Add 1 % Water charges on "W" 500.54
TOTAL 50554.58 X
Add GST on "X" (multiplying
factor 0.1405) 7102.92
TOTAL 57657.50 Y
Add 15% CPOH on "Y" 8648.62
TOTAL 66306.12 Z
Add Cess @ 1% on "Z" 663.06
Cost of 300 sqm 66969.19
Cost of 1 sqm 223.23
Say 223.25
26.84.2 Uni Axial Woven polyster geogrid of minimum tensile strength 60KN/m in the
Longitudinal direction and 20 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8980 Uni Axial Woven polyster geogrid of
minimum tensile strength 60KN/m in
the Longitudinal direction and 20 KN/m
in the Transverse direction. sqm 300.00 161.00 48300.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 2415.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 56984.04 W
Add 1 % Water charges on "W" 569.84
TOTAL 57553.88 X
Add GST on "X" (multiplying
factor 0.1405) 8086.32
TOTAL 65640.20 Y
Add 15% CPOH on "Y" 9846.03
TOTAL 75486.23 Z
Add Cess @ 1% on "Z" 754.86
Cost of 300 sqm 76241.09
Cost of 1 sqm 254.14
Say 254.15
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2177
26.84.3 Uni Axial Woven polyster geogrid of minimum tensile strength 80 KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8981 Uni Axial Woven polyster geogrid of
minimum tensile strength 80 KN/m in
the Longitudinal direction and 30 KN/m
in the Transverse direction. sqm 300.00 205.00 61500.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 3075.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 70844.04 W
Add 1 % Water charges on "W" 708.44
TOTAL 71552.48 X
Add GST on "X" (multiplying
factor 0.1405) 10053.12
TOTAL 81605.60 Y
Add 15% CPOH on "Y" 12240.84
TOTAL 93846.44 Z
Add Cess @ 1% on "Z" 938.46
Cost of 300 sqm 94784.91
Cost of 1 sqm 315.95
Say 315.95
26.84.4 Uni Axial Woven polyster geogrid of minimum tensile strength 100KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8982 Uni Axial Woven polyster geogrid of
minimum tensile strength 100KN/m in
the Longitudinal direction and 30KN/m
in the Transverse direction. sqm 300.00 237.00 71100.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2178
Code Description Unit Quantity Rate Amount
item in all respect including
transportation.i.e 5% of (P) 3555.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 80924.04 W
Add 1 % Water charges on "W" 809.24
TOTAL 81733.28 X
Add GST on "X" (multiplying
factor 0.1405) 11483.53
TOTAL 93216.81 Y
Add 15% CPOH on "Y" 13982.52
TOTAL 107199.33 Z
Add Cess @ 1% on "Z" 1071.99
Cost of 300 sqm 108271.32
Cost of 1 sqm 360.90
Say 360.90
26.84.5 Uni Axial Woven polyster geogrid of minimum tensile strength 120KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8983 Uni Axial Woven polyster geogrid of
minimum tensile strength 120KN/m in
the Longitudinal direction and 30KN/m
in the Transverse direction. sqm 300.00 254.00 76200.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 3810.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 86279.04 W
Add 1 % Water charges on "W" 862.79
TOTAL 87141.83 X
Add GST on "X" (multiplying
factor 0.1405) 12243.43
TOTAL 99385.26 Y
Add 15% CPOH on "Y" 14907.79
TOTAL 114293.05 Z
Add Cess @ 1% on "Z" 1142.93
Cost of 300 sqm 115435.98
Cost of 1 sqm 384.79
Say 384.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2179
26.84.6 Uni Axial Woven polyster geogrid of minimum tensile strength 150KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8984 Uni Axial Woven polyster geogrid of
minimum tensile strength 150KN/m in
the Longitudinal direction and 30 KN/m
in the Transverse direction. sqm 300.00 319.00 95700.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation. i.e 5% of (P) 4785.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 106754.04 W
Add 1 % Water charges on "W" 1067.54
TOTAL 107821.58 X
Add GST on "X" (multiplying
factor 0.1405) 15148.93
TOTAL 122970.51 Y
Add 15% CPOH on "Y" 18445.58
TOTAL 141416.09 Z
Add Cess @ 1% on "Z" 1414.16
Cost of 300 sqm 142830.25
Cost of 1 sqm 476.10
Say 476.10
26.84.7 Uni Axial Woven polyster geogrid of minimum tensile strength 200KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8985 Uni Axial Woven polyster geogrid of
minimum tensile strength 200KN/m in
the Longitudinal direction and 30 KN/m
in the Transverse direction. sqm 300.00 375.00 112500.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2180
Code Description Unit Quantity Rate Amount
item in all respect including
transportation.i.e 5% of (P) 5625.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 124394.04 W
Add 1 % Water charges on "W" 1243.94
TOTAL 125637.98 X
Add GST on "X" (multiplying
factor 0.1405) 17652.14
TOTAL 143290.12 Y
Add 15% CPOH on "Y" 21493.52
TOTAL 164783.63 Z
Add Cess @ 1% on "Z" 1647.84
Cost of 300 sqm 166431.47
Cost of 1 sqm 554.77
Say 554.75
26.84.8 Uni Axial Woven polyster geogrid of minimum tensile strength 250KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8986 Uni Axial Woven polyster geogrid of
minimum tensile strength 250KN/m in
the Longitudinal direction and 30KN/m
in the Transverse direction. sqm 300.00 458.00 137400.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation. i.e 5% of (P) 6870.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 150539.04 W
Add 1 % Water charges on "W" 1505.39
TOTAL 152044.43 X
Add GST on "X" (multiplying
factor 0.1405) 21362.24
TOTAL 173406.67 Y
Add 15% CPOH on "Y" 26011.00
TOTAL 199417.67 Z
Add Cess @ 1% on "Z" 1994.18
Cost of 300 sqm 201411.85
Cost of 1 sqm 671.37
Say 671.35
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2181
26.84.9 Uni Axial Woven polyster geogrid of minimum tensile strength 300KN/m in
the Longitudinal direction and 30 KN/m in the Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8987 Uni Axial Woven polyster geogrid of
minimum tensile strength 300KN/m in
the Longitudinal direction and 30KN/m
in the Transverse direction. sqm 300.00 529.00 158700.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation. i.e 5% of (P) 7935.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 172904.04 W
Add 1 % Water charges on "W" 1729.04
TOTAL 174633.08 X
Add GST on "X" (multiplying
factor 0.1405) 24535.95
TOTAL 199169.03 Y
Add 15% CPOH on "Y" 29875.35
TOTAL 229044.38 Z
Add Cess @ 1% on "Z" 2290.44
Cost of 300 sqm 231334.83
Cost of 1 sqm 771.12
Say 771.10
26.85 Supplying and laying of Bi-Axial Woven Polyster Geogrid conforming to
MORTH 3100 and IRC113, as soil reinforcement/basal reinforcement of
granular road base and sub base, area stalilization, track bed stabilization,
load transfer platforms Including accessories like tie-strips, nuts & bolts and
loops/lugs for joining reinforcing elements with the facia pannels, overlaps
and other protective elements for synthetic geo-grids and all other activities
required etc. complete as per design requirements, manufacturer
specifications and as per direction of engineer-in- charge.
26.85.1 Bi Axial Woven polyster geogrid of minimum tensile strength 20KN/m in both
Longitudinal and Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2182
Code Description Unit Quantity Rate Amount
8988 Bi Axial Woven polyster geogrid of
minimum tensile strength 20KN/m in
both Longitudinal and Transverse
direction. sqm 300.00 114.00 34200.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 1710.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 42179.04 W
Add 1 % Water charges on "W" 421.79
TOTAL 42600.83 X
Add GST on "X" (multiplying
factor 0.1405) 5985.42
TOTAL 48586.25 Y
Add 15% CPOH on "Y" 7287.94
TOTAL 55874.18 Z
Add Cess @ 1% on "Z" 558.74
Cost of 300 sqm 56432.93
Cost of 1 sqm 188.11
Say 188.10
26.85.2 Bi Axial Woven polyster geogrid of minimum tensile strength 40KN/m in both
Longitudinal and Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8989 Bi Axial Woven polyster geogrid of
minimume tensile strength 40KN/m in
both Longitudinal and Transverse
direction. sqm 300.00 173.00 51900.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 2595.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2183
Code Description Unit Quantity Rate Amount
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 60764.04 W
Add 1 % Water charges on "W" 607.64
TOTAL 61371.68 X
Add GST on "X" (multiplying
factor 0.1405) 8622.72
TOTAL 69994.40 Y
Add 15% CPOH on "Y" 10499.16
TOTAL 80493.56 Z
Add Cess @ 1% on "Z" 804.94
Cost of 300 sqm 81298.50
Cost of 1 sqm 270.99
Say 271.00
26.85.3 Bi Axial Woven polyster geogrid of minimum tensile strength 60KN/m in both
Longitudinal and Transverse direction.
Code Description Unit Quantity Rate Amount
Details of Cost for 300 Sqm.
MATERIALS:
8990 Bi Axial Woven polyster geogrid of
minimum tensile strength 60KN/m in
both Longitudinal and Transverse
direction. sqm 300.00 223.00 66900.00 P
Add 5 percent of the cost of reinforcing
elements geogrid for wastage and
accessories like tie-strips, nuts and
bolts and loops/lungs for joining
reinforcing elements with the facia
panels, overlaps and other protective
elements for geogrid and all other
activities required to complete the
item in all respect including
transportation.i.e 5% of (P) 3345.00
LABOUR:
0128 Mate day 0.36 714.00 257.04
0114 Beldar day 6.00 645.00 3870.00
0139 Skilled Beldar day 3.00 714.00 2142.00
Total 76514.04 W
Add 1 % Water charges on "W" 765.14
TOTAL 77279.18 X
Add GST on "X" (multiplying
factor 0.1405) 10857.72
TOTAL 88136.91 Y
Add 15% CPOH on "Y" 13220.54
TOTAL 101357.44 Z
Add Cess @ 1% on "Z" 1013.57
Cost of 300 sqm 102371.02
Cost of 1 sqm 341.24
Say 341.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2184
26.86 Providing and fixing factory made single extruded WPC (Wood Polymer
Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat
comprising of virgin PVC polymer of K value 58-60 (Suspension Grade),
calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk)
and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated
with miter joints after applying PVC solvent cement and screwed with full
body threaded star headed SS screws having minimum frame density of 750
kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),
minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/
mm2 and resistance to spread of flame of Class A category with property of
being termite/borer proof, water/moisture proof and fire retardant and fixed
in position with M.S hold fast/lugs/SS dash fasteners of required dia and length
complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS
dash fasteners shall be paid for separately).
Note: For WPC solid door/window frames, minus 5mm tolerance in
dimensions i.e depth and width of profile shall be acceptable. Variation in
profile dimensions on plus side shall be acceptable but no extra payment on
this account shall be made.
26.86.1 Frame size 45 x 70 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre)"
MATERIAL
5747 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 45 x
70 mm including carriage of frame metre 5.20 375.00 1950.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 2457.23 W
Add 1 % Water charges on "W" 24.57
TOTAL 2481.80 X
Add GST on ''X'' (multiplying
factor 0.1405) 348.69
TOTAL 2830.50 Y
Add 15% CPOH on "Y" 424.57
TOTAL 3319.35 Z
Add Cess @ 1% on "Z" 33.19
Cost of 5.20 metre 3352.54
Cost of 1 metre 644.72
Say 644.70
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2185
26.86.2 Frame size 45 x 85 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre.)
MATERIAL
5748 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 45 x
85 mm including carriage of frame metre 5.20 525.00 2730.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 3237.23 W
Add 1 % Water charges on "W" 32.37
TOTAL 3269.60 X
Add GST on ''X'' (multiplying
factor 0.1405) 459.38
TOTAL 3728.98 Y
Add 15% CPOH on "Y" 559.35
TOTAL 4288.33 Z
Add Cess @ 1% on "Z" 42.88
Cost of 5.20 metre 4331.21
Cost of 1 metre 832.93
Say 832.95
26.86.3 Frame size 50 x 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre)
MATERIAL
5749 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 50 x
100 mm including carriage of frame metre 5.20 540.00 2808.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2186
Code Description Unit Quantity Rate Amount
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 3315.23 W
Add 1 % Water charges on "W" 33.15
TOTAL 3348.38 X
Add GST on ''X'' (multiplying
factor 0.1405) 470.45
TOTAL 3818.83 Y
Add 15% CPOH on "Y" 572.82
TOTAL 4391.65 Z
Add Cess @ 1% on "Z" 43.92
Cost of 5.20 metre 4435.57
Cost of 1 metre 852.99
Say 853.00
26.86.4 Frame size 50 x 125 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre.)
MATERIAL
5750 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 50 x
125 mm including carriage of frame metre 5.20 630.00 3276.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 3783.23 W
Add 1 % Water charges on "W" 37.83
TOTAL 3821.06 X
Add GST on ''X'' (multiplying
factor 0.1405) 536.86
TOTAL 4357.92 Y
Add 15% CPOH on "Y" 653.69
TOTAL 5011.61 Z
Add Cess @ 1% on "Z" 50.12
Cost of 5.20 metre 5061.73
Cost of 1 metre 973.41
Say 973.40
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2187
26.86.5 Frame size 65 x 100 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre.)
MATERIAL
5751 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 65 x
100 mm including carriage of frame metre 5.20 650.00 3380.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 3887.23 W
Add 1 % Water charges on "W" 38.87
TOTAL 3926.10 X
Add GST on ''X'' (multiplying
factor 0.1405) 551.62
TOTAL 4477.72 Y
Add 15% CPOH on "Y" 671.66
TOTAL 5149.38 Z
Add Cess @ 1% on "Z" 51.49
Cost of 5.20 metre 5200.87
Cost of 1 metre 1000.17
Say 1000.15
26.86.6 Frame size 65 x 125 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre.)
MATERIAL
5752 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 65 x
125 mm including carriage of frame metre 5.20 835.00 4342.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2188
Code Description Unit Quantity Rate Amount
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 4849.23 W
Add 1 % Water charges on "W" 48.49
TOTAL 4897.72 X
Add GST on ''X'' (multiplying
factor 0.1405) 688.13
TOTAL 5585.85 Y
Add 15% CPOH on "Y" 837.88
TOTAL 6423.73 Z
Add Cess @ 1% on "Z" 64.24
Cost of 5.20 metre 6487.97
Cost of 1 metre 1247.69
Say 1247.70
26.86.7 Frame size 65 x 150 mm
Code Description Unit Quantity Rate Amount
Details of cost for 5.20 metre of door
frame/chowkhat size 1.00 x 2.10 metre.
(1.00+2.10+2.10=5.20 metre.)
MATERIAL
5753 Factory made single extruded WPC
(Wood Polymer Composite) solid door/
window, clerestory windows & other
Frames/Chowkhat of frame size 65 x
150 mm including carriage of frame metre 5.20 1010.00 5252.00
LABOUR
For fabrication and fixing in position
0156 Carpenter (average) day 0.10 749.00 74.90
0155 Mason (average) day 0.17 749.00 127.33
0114 Beldar day 0.44 645.00 283.80
9999 Sundries includes PVC solvent cement
and SS screws etc. L.S. 10.00 2.12 21.20
TOTAL 5759.23 W
Add 1 % Water charges on "W" 57.59
TOTAL 5816.82 X
Add GST on ''X'' (multiplying
factor 0.1405) 817.26
TOTAL 6634.09 Y
Add 15% CPOH on "Y" 995.11
TOTAL 7629.20 Z
Add Cess @ 1% on "Z" 76.29
Cost of 5.20 metre 7705.49
Cost of 1 metre 1481.83
Say 1481.85
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2189
26.87 Providing and fixing factory made single extruded WPC (Wood Polymer
Composite) solid plain flush door shutter of required size comprising of virgin
polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural
fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum
toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and
screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum
compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and
resistance to spread of flame of Class A category with property of being
termite/borer proof, water/moisture proof and fire retardant and fixing with
stainless steel butt hinges of required size with necessary full body threaded
star headed counter sunk S.S screws, all as per direction of Engineer-In-
Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be
paid separately)
26.87.1 30 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for door shutter of
size 2.20 sqm.
MATERIAL
5754 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
flush door shutter 30mm thick sqm 2.20 2800.00 6160.00
9977 Carriage of door shutter L.S. 29.64 2.12 62.84
LABOUR
For fixing shutter
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 6501.64 W
Add 1 % Water charges on "W" 65.02
TOTAL 6566.65 X
Add GST on ''X'' (multiplying
factor 0.1405) 922.61
TOTAL 7489.27 Y
Add 15% CPOH on "Y" 1123.39
TOTAL 8612.66 Z
Add Cess @ 1% on "Z" 86.13
Cost of 2.20 sqm. 8698.78
Cost of 1 sqm. 3953.99
Say 3954.00
26.87.2 35 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for door shutter of
size 2.20 sqm.
MATERIAL
5755 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
flush door shutter 35 mm thick sqm 2.20 3250.00 7150.00
9977 Carriage of door shutter L.S. 29.64 2.12 62.84
LABOUR
For fixing shutter
0156 Carpenter (average) day 0.20 749.00 149.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2190
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.20 645.00 129.00
TOTAL 7491.64 W
Add 1 % Water charges on "W" 74.92
TOTAL 7566.55 X
Add GST on ''X'' (multiplying
factor 0.1405) 1063.10
TOTAL 8629.65 Y
Add 15% CPOH on "Y" 1294.45
TOTAL 9924.10 Z
Add Cess @ 1% on "Z" 99.24
Cost of 2.20 sqm. 10023.34
Cost of 1 sqm. 4556.06
Say 4556.05
26.88 Providing and fixing factory made single extruded WPC (Wood Polymer
Composite) solid decorative type flush door shutter of required size
comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium
carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non
toxic additives (maximum toxicity index of 12 for 100 gms) having minimum
density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900
N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity
850 N/mm2 and resistance to spread of flame of Class A category with
property of being termite/borer proof, water/moisture proof and fire retardant.
WPC to be laminated with PVC foil of minimum 14 microns thick of approved
design pasted with hot melt adhesive on both faces of shutter and fixing with
stainless steel butt hinges of required size with necessary full body threaded
star headed counter sunk S.S screws, all as per direction of Engineer-In-
Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be
paid separately)
26.88.1 30 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for door shutter of
size 2.20 sqm.
MATERIAL
5754 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
flush door shutter 30mm thick sqm 2.20 2800.00 6160.00
5761 PVC laminated foil of minimum
thickness of 14 microns of approved
design sqm 4.40 125.00 550.00
9977 Carriage of door shutter L.S. 29.64 2.12 62.84
LABOUR
For pasting PVC laminated foil to door
shutter and fixing door shutter at
position
0156 Carpenter (average) day 0.20 749.00 149.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2191
Code Description Unit Quantity Rate Amount
0114 Beldar day 0.30 645.00 193.50
TOTAL 7116.14 W
Add 1 % Water charges on "W" 71.16
TOTAL 7187.30 X
Add GST on ''X'' (multiplying
factor 0.1405) 1009.82
TOTAL 8197.11 Y
Add 15% CPOH on "Y" 1229.57
TOTAL 9426.68 Z
Add Cess @ 1% on "Z" 94.27
Cost of 2.20 sqm. 9520.95
Cost of 1 sqm. 4327.70
Say 4327.70
26.88.2 35 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for door shutter of
size 2.20 sqm.
MATERIAL
5755 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
flush door shutter 35 mm thick sqm 2.20 3250.00 7150.00
5761 PVC laminated foil of minimum
thickness of 14 microns of approved
design sqm 4.40 125.00 550.00
9977 Carriage of door shutter L.S. 29.64 2.12 62.84
LABOUR
For pasting PVC laminated foil to
door shutter and fixing door shutter
at position
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.30 645.00 193.50
TOTAL 8106.14 W
Add 1 % Water charges on "W" 81.06
TOTAL 8187.20 X
Add GST on ''X'' (multiplying
factor 0.1405) 1150.30
TOTAL 9337.50 Y
Add 15% CPOH on "Y" 1400.62
TOTAL 10738.12 Z
Add Cess @ 1% on "Z" 107.38
Cost of 2.20 sqm. 10845.51
Cost of 1 sqm. 4929.78
Say 4929.80
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2192
26.89 Providing and fixing factory made single extruded WPC (Wood Polymer
Composite) solid board one side white color and other side of board laminted
with PVC foil of minimum 14 micron thickness of approved design pasted
with hot melt adhesive for cup boards, work stations and bathroom/kitchen
cabinet etc. of required sizes comprising of virgin polymer of K value 58-60
(Suspension Grade), calcium carbonate and natural fibers (wood powder/
rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12
for 100 gms) having minimum density of 650 kg/cum and screw withdrawal
strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50
N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame
of Class A category with property of being termite/borer proof, water/moisture
proof and fire retardant and fixing with stainless steel piano hinges/soft close
clip on concealed hinges of required size with necessary full body threaded
star headed counter sunk S.S screws, all as per direction of Engineer-In-
Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges
and necessary S.S screws shall be paid separately)
26.89.1 18 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for 18 mm thick WPC
board for cupboard shutter of size
2.0x1.08 metre = 2.16 sqm
MATERIAL
5756 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
white colored board of 18 mm thick sqm 2.16 1750.00 3780.00
5761 PVC laminated foil of minimum
thickness of 14 microns of approved
design sqm 2.16 125.00 270.00
9977 Carriage of board L.S. 5.00 2.12 10.60
9999 Sundries L.S. 20.00 2.12 42.40
LABOUR
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 4381.80 W
Add 1 % Water charges on "W" 43.82
TOTAL 4425.62 X
Add GST on ''X'' (multiplying
factor 0.1405) 621.80
TOTAL 5047.42 Y
Add 15% CPOH on "Y" 757.11
TOTAL 5804.53 Z
Add Cess @ 1% on "Z" 58.05
Cost of 2.16 sqm. 5862.58
Cost of 1 sqm. 2714.16
Say 2714.15
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2193
26.89.2 25 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for 25 mm thick WPC
board for cupboard shutter of size
2.0x1.08 metre = 2.16 sqm
MATERIAL
5757 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
white colored board of 25 mm thick sqm 2.16 2360.00 5097.60
5761 PVC laminated foil of minimum
thickness of 14 microns of approved
design sqm 2.16 125.00 270.00
9977 Carriage of board L.S. 5.00 2.12 10.60
9999 Sundries L.S. 20.00 2.12 42.40
LABOUR
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 5699.40 W
Add 1 % Water charges on "W" 56.99
TOTAL 5756.39 X
Add GST on ''X'' (multiplying
factor 0.1405) 808.77
TOTAL 6565.17 Y
Add 15% CPOH on "Y" 984.78
TOTAL 7549.94 Z
Add Cess @ 1% on "Z" 75.50
Cost of 2.16 sqm. 7625.44
Cost of 1 sqm. 3530.30
Say 3530.30
26.90 Providing and fixing factory made single extruded WPC (Wood Polymer
Composite) solid plain white color board for backing of cup boards and
bathroom/kitchen cabinets etc. of required size comprising of virgin polymer
of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers
(wood powder/ rice husk/wheat husk) and non toxic additives (maximum
toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and
screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum
compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and
resistance to spread of flame of Class A category with property of being
termite/borer proof, water/moisture proof and fire retardant and fixing with
stainless steel screws etc. all as per direction of Engineer-In- Charge. (Note:
stainless steel screws shall be paid separately)
26.90.1 6 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for 6 mm thick WPC
board for backing of cupboard of size
2.0x1.08 metre = 2.16 sqm
MATERIAL
5758 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
white colored board of 6 mm thick sqm 2.16 600.00 1296.00
9977 Carriage of board L.S. 5.00 2.12 10.60
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2194
Code Description Unit Quantity Rate Amount
LABOUR
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 1585.40 W
Add 1 % Water charges on "W" 15.85
TOTAL 1601.25 X
Add GST on ''X'' (multiplying
factor 0.1405) 224.98
TOTAL 1826.23 Y
Add 15% CPOH on "Y" 273.93
TOTAL 2100.16 Z
Add Cess @ 1% on "Z" 21.00
Cost of 2.16 sqm. 2121.17
Cost of 1 sqm. 982.02
Say 982.00
26.90.2 12 mm thick
Code Description Unit Quantity Rate Amount
Details of cost for 12 mm thick WPC
board for cupboard shutter of size
2.0x1.08 metre = 2.16 sqm
MATERIAL
5759 Factory made single extruded WPC
(Wood Polymer Composite) solid plain
white colored board of 12 mm thick sqm 2.16 1020.00 2203.20
9977 Carriage of board L.S. 5.00 2.12 10.60
LABOUR
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.20 645.00 129.00
TOTAL 2492.60 W
Add 1 % Water charges on "W" 24.93
TOTAL 2517.53 X
Add GST on ''X'' (multiplying
factor 0.1405) 353.71
TOTAL 2871.24 Y
Add 15% CPOH on "Y" 430.69
TOTAL 3301.92 Z
Add Cess @ 1% on "Z" 33.02
Cost of 2.16 sqm. 3334.94
Cost of 1 sqm. 1543.96
Say 1543.95
26.91 Providing and fixing factory made 18 mm thick single extruded WPC (Wood
Polymer Composite) solid plain white colour board Jali, CNC (Computer
numeric control) routed of approved design by Engineer-in -charge which
are machine cut for duct/shaft covering, partitions and facades comprising
of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate
and natural fibers (wood powder/ rice husk/wheat husk) and non toxic
additives(maximum toxicity index of 12 for 100 gms) having minimum density
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2195
of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum
compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and
resistance to spread of flame of Class A category with properties of being
termite/borer proof, water/moisture proof and fire retardant and fixing on M.S
(mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section
including applying a priming coat of approved steel primer, placed at grid
made at 1.0 x 1.0 m or as per requirement at site with necessary stainless
steel fasteners and SS screws etc., all complete as per direction of Engineer-
In- Charge.
(Note: M.S (mild steel) framework with priming coat and necessary SS
fasteners and SS screws shall be paid separately.
Code Description Unit Quantity Rate Amount
Details of cost for WPC jali of
size 1.80 x 2.40 metre = 4.32 sqm
MATERIAL
5760 Factory made 18 mm thick single
extruded WPC (Wood Polymer
Composite) solid plain white colour
board Jali including carriage sqm 4.32 2260.00 9763.20
9999 Sundries L.S. 10.00 2.12 21.20
LABOUR
0156 Carpenter (average) day 0.20 749.00 149.80
0114 Beldar day 0.30 645.00 193.50
TOTAL 10127.70 W
Add 1 % Water charges on "W" 101.28
TOTAL 10228.98 X
Add GST on ''X'' (multiplying
factor 0.1405) 1437.17
TOTAL 11666.15 Y
Add 15% CPOH on "Y" 1749.92
TOTAL 13416.07 Z
Add Cess @ 1% on "Z" 134.16
Cost of 4.32 sqm. 13550.23
Cost of 1 sqm. 3136.63
Say 3136.65
26.92 Providing and fixing of façade at all heights with extruded hollow Clay /
Terracotta ventilated rainscreen tiles of height 250/ 300/ 400mm and length of
595 mm of approved texture,design and pattern having Flexural Strength/
Modulus of Rupture of ? 14 N/m² and maximum water absorption of 10% tested
as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level
fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of
vertical 'T' (for intermediates)/ 'L'(for ends/ termination)/ Tubular sections (at
corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at
maximum spacing of 600mm c/c matching to the tile vertical grid, and
horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length
150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on
top of the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the
tile horizontal grid with two numbers of self-drilling / self-tapping SS screws
of size 5.5x25 mm with EPDM washers.
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2196
The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-
dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80
microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and
of size 220x110x12 mm at outer corners and stainless steel grade 304,M10
full threaded anchor fasteners with nylon sleeve 100mm long (for brick work)
and M8 expansion anchor fasteners 75mm long for concrete surface, spacing
of brackets to be based on a structural/ static calculation. The brackets shall
be of length 175mm at junction of two vertical aluminium profiles and of length
100mm at intermediate points of vertical profiles and shall be fixed to the
vertical aluminium T / L / Tubular profiles using two numbers self-drilling/
self-tapping SS screws of size 5.5x25mm with EPDM washers.
EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles
shall be mounted on the ‘C’ clamps such that the tiles are supported at top
and bottom at both ends. The tiles shall be additionally secured to the
horizontal ‘C’ clamps using special SS clips of required size which shall be
inserted and pressed into position on the ‘C’ clamps holding the tiles and the
cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS
Polymer sealant adhesive. The vertical joint open groove between two adjacent
tiles shall be 5mm. The tiles and system shall be designed to resist wind load
as per IS 875 (Part 3) according to different zones. The tiles shall be installed
using the ventilated rain screen principle with provision for natural ventilation
of the space between the façade tiles and the structural wall. The work shall
be carried out as per specification, drawing and as per direction of the
Engineer-in-Charge.
Note : Scaffolding wherever required to be paid separately.
26.92.1 With 16mm thickness (+/- 10%) terracotta tiles of grey colour
Code Description Unit Quantity Rate Amount
Detail of cost for 10.80 sqm
(3.60 x 3.0 metre)
MATERIAL
Façade area = 10.80 sqm + Wastage
@ 5% = 0.54 sqm. Total = 11.34 sqm
5762 16mm thick extruded terracotta tiles of
grey colour of size 300 x 595mm sqm 11.34 2152.80 24412.75
7306 Aluminium Tube / T Profile kgs 17.10 190.00 3249.00
1). At outer corners tubular section
40x40x2 mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.82 kg/mtr. = 4.92 kg
2). At ends/termination angle 40x60x2
mm = 2 nos. 3 mtr. long = 6.00 mtr. @
0.53 kg/mtr. = 3.18 kg
3). At intermediate T section
80x60x2mm = 4 nos. 3 mtr. long =
12.00 mtr. @ 0.75 kg/mtr. = 9.00 kg
(Total = 4.92+3.18+9.00 = 17.10 kg.
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2197
Code Description Unit Quantity Rate Amount
7306 Aluminium “C” Clamps of size
80x25x2 mm - 150mm kgs 7.24 190.00 1375.60
(i) 150mm longh = 4x11 no. = 44.00
nos. x 0.15 = 6.6 mtr. @ 0.628 kg/mtr.
= 4.14 kg
(ii) 75mm long 6x11=66.00 nos. x
0.075 = 4.95 mtr. @ 0.628 kg/mtr.=
3.10 kg. Total=4.14 + 3.10 = 7.24 kg
7216 Self-Drilling/Self-Tapping Screws
M-6 25mm long each 284.00 3.00 852.00
(a) Bracket to vertical profile - 32 Nos.
(brackets) x2.00 nos. = 64.00 Nos
b) For fixing of C” clamps to vertical
profile (44+66=110)x2=220 nos.
Total = 220 Nos + 64 Nos = 284.00
Nos
1007 HDG Mild Steel Brackets (Minimum
18 microns Galvanizing) quintal 0.6034 4950.00 2986.83
a) Wall bracket = 110x80x6 mm thick
(i) 100 mm long = 12x0.10= 1.20 Mtr
@ 8.65 kg/mtr. = 10.38 kg “(ii) 175mm
long = 12x0.175=2.10 mtr. @ 8.65 kg/
mtr. = 18.17 kg
Total = 10.38 + 18.17 = 28.55 kg
b) Corner Bracket of size 200 x 100 x
12mm thick
(a) 100mm long - 4 Nos x0.10x = 0.40
mtr. @ 28.90 Kgs = 11.56 Kg
(b) 175mm long 4x0.175= 0.70 mtr. @
28.90 kg/mtr. = 20.23 kg
Total = 11.56 + 20.23 = 31.79 kg. Total
quantity of wall and corner bracket =
60.34 kgs = 0.6034 quintal
7217 SS anchor Fasteners (RCC / Brick) –
M-8x75mm/M-10x100mm each 32.00 70.00 2240.00
8x4 nos. = 32 Nos Bracket
7390 EPDM Gaskets of size 100x80 mm metre 3.20 15.00 48.00
32x0.10=3.20 mtr.
7218 MS Polymer Sealant Adhesive litre 0.15 1200.00 180.00
Area = 10.8 Sqm + wastage @
0.54 sqm. = 11.34 Sqm
Adhesive required = Approx.
150ml or 0.15 Ltr.
SS Clips
7219 SS Double Clip at intermediate each 140.00 7.00 980.00
7x10=70.00 Nos. x 2 clips
= 140.00 clips
7220 SS Single clip at top and bottom each 28.00 4.00 112.00
7x4= 28 Nos. clips
LABOUR
0166 Installation charges for fixing of façade
at all heights with extruded hollow clay/
terracotta ventillated rain screen tiles sqm 10.80 645.00 6966.00
9999 Carriage of materials L.S. 125.00 2.12 265.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2198
Code Description Unit Quantity Rate Amount
9999 T&P and materials Lead & Lift L.S. 250.00 2.12 530.00
TOTAL 44197.18 W
Add 1 % Water charges on "W" 441.97
TOTAL 44639.15 X
Add GST on "X" (multiplying
factor 0.1405) 6271.80
TOTAL 50910.95 Y
Add 15% CPOH on "Y" 7636.64
TOTAL 58547.60 Z
Add Cess @ 1% on "Z" 585.48
Cost of 10.80 sqm. 59133.07
Cost of 1 sqm 5475.28
Say 5475.30
26.92.2 With 16mm thickness (+/- 10%) terracotta tiles of other than grey colors
Code Description Unit Quantity Rate Amount
Detail of cost for 10.80 sqm
(3.60 x 3.0 metre)
MATERIAL
Façade area = 10.80 sqm + Wastage
@ 5% = 0.54sqm. Total = 11.34 sqm
5763 16mm thick extruded terracotta tiles of
other than grey colour of size 300 x
595mm sqm 11.34 1991.30 22581.34
7306 Aluminium Tube / T Profile kgs 17.10 190.00 3249.00
1). At outer corners tubular section
40x40x2 mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.82 kg/mtr. = 4.92 kg 2).
At ends/termination angle 40x60x2 mm
= 2 nos. 3 mtr. long = 6.00 mtr. @ 0.53
kg/mtr. = 3.18 kg 3). At intermediate T
section 80x60x2mm = 4 nos. 3 mtr.
long = 12.00 mtr. @ 0.75 kg/mtr. =
9.00 kg (Total = 4.92+3.18+9.00 =
17.10 kg.
7306 Aluminium “C” Clamps of size
56x25x2mm kgs 7.24 190.00 1375.60
(i) 150mm long = 4x11 no. = 44.00
nos. x 0.15 = 6.6 mtr. @ 0.628 kg/mtr.
= 4.14 kg (ii) 75mm long 6x11=66.00
nos. x 0.075 = 4.95 mtr. @ 0.628 kg/
mtr.= 3.10 kg. Total=4.14 + 3.10 =
7.24 kg
7216 Self-Drilling/Self-Tapping Screws
M-6 25mm long each 284.00 3.00 852.00
(a) Bracket to vertical profile - 32
Nos.x2.00 nos. = 64.00 Nos b) For
fixing of brackets to “C” clamps
(44+66=110)x2=220 nos. Total = 220
Nos + 64 Nos = 284.00 Nos
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2199
Code Description Unit Quantity Rate Amount
1007 HDG Mild Steel Brackets (Minimum 18
microns Galvanizing) quintal 0.6034 4950.00 2986.83
a) Wall bracket - Average 110 x 80 =
6mm thick
(i) 100 mm long = 12x0.10= 1.20 Mtr
@ 8.65 kg/mtr. = 10.38 kg
(ii) 175mm long = 12x0.175=2.10 mtr.
@ 8.65 kg/mtr. = 18.17 kg
Total = 10.38 + 18.17 = 28.55 kg
b) Corner Bracket of size 200 x 100 x
12mm thick
(a) 100mm long - 4 Nos x0.10x = 0.40
mtr. @ 28.90 Kgs = 11.56 Kg
(b) 175mm long 4x0.175= 0.70 mtr. @
28.90 kg/mtr. = 20.23 kg
Total = 11.56 + 20.23 = 31.79 kg.
Total quantity of wall and corner
bracket = 60.34 kgs = 0.6034 quintal
7217 SS anchor Fasteners (RCC / Brick) –
M-8x75 mm/M-10x100mm each 32.00 70.00 2240.00
8x4 nos. = 32 Nos Bracket
7390 EPDM Gaskets of size 100x80 mm metre 3.20 15.00 48.00
32x0.10=3.20 mtr.
7218 MS Polymer Sealant Adhesive litre 0.15 1200.00 180.00
Area - 10.8 Sqm + wastage @ 0.54
sqm. Total =11.34 Sqm Adhesive
required = Approx. 150ml or 0.15 ltr.
SS Clips
7219 SS Double Clip at intermediate each 140.00 7.00 980.00
7x10=70.00 Nos. x 2 clips
= 140.00 clips
7220 SS Single clip at Top and Bottom each 28.00 4.00 112.00
7x4= 28 Nos. clips
LABOUR
0166 Installation charges for fixing of façade
at all heights with extruded hollow clay/
terracotta ventillated rain screen tiles sqm 10.80 645.00 6966.00
9999 Carriage of materials L.S. 125.00 2.12 265.00
9999 T&P and materials Lead & Lift L.S. 250.00 2.12 530.00
TOTAL 42365.77 W
Add 1 % Water charges on "W" 423.66
TOTAL 42789.43 X
Add GST on "X" (multiplying
factor 0.1405) 6011.91
TOTAL 48801.34 Y
Add 15% CPOH on "Y" 7320.20
TOTAL 56121.55 Z
Add Cess @ 1% on "Z" 561.22
Cost of 10.80 sqm. 56682.76
Cost of 1 sqm 5248.40
Say 5248.40
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2200
26.93 Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta
ventilated rainscreen tiles of height 259/ 309/ 409mm and lengthof 1190 mm of
approved texture,design and pattern having Flexural Strength/ Modulus of
Rupture of ? 14 N/m² and maximum water absorption of 10% tested as per ISO
10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a
supporting aluminium framework (Alloy 6063 T5/T6) consisting of vertical 'T'
(for intermediates)/ 'L' (for ends/ termination)/ Tubular sections (at corners)of
size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum
spacing of 1200mm c/c matching to the tile vertical grid, and horizontal aluminium
'C'-clamps of size 56x34x2 mm thickness of length 150mm at junction of tiles
and of length 75mm at wall ends/ corners fixed on top of the vertical sections at
spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two
numbers of self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM
washers.
The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-
dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)
of size 110x80x6 mm at intermediate vertical aluminium profiles and of size
220x110x12 mmat outer corners and stainless steel grade 304,M10 full threaded
anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion
anchor fasteners 75mm long for concrete surface, spacing of brackets to be
based on a structural/ static calculation. The brackets shall be of length 175mm
at junction of two vertical aluminium profiles and of length 100mm at intermediate
points of vertical profiles and shall be fixed to the vertical aluminium T / L /
Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size
5.5x25 mm with EPDM washers.
EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles
shall be mounted on the ‘C’ clamps such that the tiles are supported at top and
bottom at both ends. The tiles shall be mounted on the C-clamps with EPDM
profiles in between such that the tiles are supported at top and bottom at both
ends. The vertical joint open groove between two adjacent tiles shall be 10mm.
The tiles and system shall be designed to resist wind load as per IS 875 (Part 3)
according to different zones. The tiles shall be installed using the ventilated rain
screen principle with provision for natural ventilation of the space between the
façade tiles and the structural wall. The work shall be carried out as per
specification, drawing and as per direction of the Engineer-in-Charge.“Note :
Scaffolding wherever required to be paid separately.
26.93.1 With 24mm thickness (+/- 10%) terracotta tiles of grey colour
Code Description Unit Quantity Rate Amount
Detail of cost for 12.60 sqm
(4.2 (0.3+3.6+0.3) x 3.0 metre)
MATERIAL
Façade area = 12.60 sqm + Wastage
@ 5% = 0.63 sqm. Total = 13.23 sqm
5764 24mm thick extruded terracotta tiles of
grey color of size 309x1190 mm and
length 1190mm sqm 13.23 2475.00 32744.25
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2201
Code Description Unit Quantity Rate Amount
7306 Aluminium Tube / T Profile kgs 12.60 190.00 2394.00
1). At outer corners tubular section
40x40x2 mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.82 kg/mtr. = 4.92 kg
2). At ends/termination angle 40x60x2
mm = 2 nos. 3 mtr. long = 6.00 mtr. @
0.53 kg/mtr. = 3.18 kg
3). At intermediate T section
80x60x2mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.75 kg/mtr. = 4.50 kg
(Total = 4.92+3.18+4.50 = 12.60 kg
7306 Aluminium C Clamps of size
56x34x2.0 mm kgs 5.07 190.00 963.30
(i) 150mm long - 2x11 no. = 22.00 nos.
x 0.15 = 3.3 mtr. @ 0.615 kg/mtr. =
2.03 kg
(ii) 75mm long - 6x11=66.00 nos. x
0.075 = 4.95 mtr. @ 0.615 kg/mtr.=
3.04 kg
Total=2.03 + 3.04 = 5.07 kg
7221 Self-Drilling/Self-Tapping Screws
5.5x25 mm long each 236.00 3.00 708.00
(a) Bracket to vertical profile -
30 Nos.x2.00 nos. = 60.00 Nos
b) For fixing of brackets to “C” clamps
(22+66=88)x2=176 nos.
Total = 176 Nos + 60 = 236.00 Nos
1007 HDG Mild Steel Brackets (Minimum
80 microns Galvanizing) quintal 0.6358 4950.00 3147.21
a) Wall bracket - 110 x 80x6mm thick
(i) 100 mm long = 10x0.10= 1.00 Mtr
@ 8.65 kg/mtr. = 8.65 kg
(ii) 175mm long = 10x0.175=1.75 mtr.
@ 8.65 kg/mtr. = 15.13 kg
Total = 8.65 + 15.13 = 23.85 kg
b) Corner Bracket of size 220 x
110 x 12mm thick
(a) 100mm long - 5 Nos x0.10
= 0.50 mtr. @ 28.90 kg/mtr. = 14.45 Kg
(b) 175mm long - 5x0.175= 0.875 mtr.
@ 28.90 kg/mtr. = 25.28 kg
Total = 14.45 + 25.28 = 39.73 kg
Gross total = 23.85+39.73 = 63.58 kg
= 0.6358 quintal
7222 SS Anchor Fasteners (RCC / Brick)
– M-8x100 mm each 30.00 70.00 2100.00
6x5 nos. = 30 Nos Bracket
7390 EPDM Gaskets of size 100x80 mm metre 3.00 15.00 45.00
30x0.10=3.00 mtr.
7218 MS Polymer Sealant Adhesive litre 0.175 1200.00 210.00
Area = 12.60 Sqm + 5% = 13.23 Sqm
Adhesive required = 175 ml. or 0.175 ltr.
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2202
Code Description Unit Quantity Rate Amount
7390 EPDM gasket for tiles mounting on
C - clamps metre 8.25 15.00 123.75
(i) 150mm long - 2x11 no.
= 22.00 nos. x 0.15 =3.3 mtr.
(ii) 75mm long - 6x11=66.00 nos.
x 0.075 = 4.95 mtr.
Total = 3.3 + 4.95 = 8.25 mtr.
LABOUR
0166 Installation charges for fixing of façade
at all heights with extruded hollow clay/
terracotta ventillated rain screen tiles sqm 12.60 645.00 8127.00
9999 Carriage of materials L.S. 125.00 2.12 265.00
9999 T&P and materials Lead & Lift L.S. 250.00 2.12 530.00
TOTAL 51357.51 W
Add 1 % Water charges on "W" 513.58
TOTAL 51871.09 X
Add GST on "X" (multiplying
factor 0.1405) 7287.89
TOTAL 59158.97 Y
Add 15% CPOH on "Y" 8873.85
TOTAL 69676.38 Z
Add Cess @ 1% on "Z" 696.76
Cost of 12.60 sqm. 70373.14
Cost of 1 sqm 5585.17
Say 5585.15
26.93.2 With 24mm thickness (+/- 10%) terracotta tiles of other than grey colors
Code Description Unit Quantity Rate Amount
Detail of cost for 12.60 sqm
(4.2 (0.3+3.6+0.3) x 3.0 metre)
MATERIAL
Façade area = 12.60 sqm + Wastage
@ 5% = 0.63 sqm. Total = 13.23 sqm
5765 24mm thick extruded terracotta tiles of
grey color of size 309x1190 mm and
length 1190mm sqm 13.23 2260.00 29899.80
7306 Aluminium Tube / T Profile kgs 12.60 190.00 2394.00
1). At outer corners tubular section
40x40x2 mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.82 kg/mtr. = 4.92 kg
2). At ends/termination angle 40x60x2
mm = 2 nos. 3 mtr. long = 6.00 mtr. @
0.53 kg/mtr. = 3.18 kg
3). At intermediate T section
80x60x2mm = 2 nos. 3 mtr. long =
6.00 mtr. @ 0.75 kg/mtr. = 4.50 kg
(Total = 4.92+3.18+4.50 = 12.60 kg)
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2203
Code Description Unit Quantity Rate Amount
7306 Aluminium C Clamps of size
56x34x2.0 mm kgs 5.07 190.00 963.30
(i) 150mm long - 2x11 no. = 22.00 nos.
x 0.15 = 3.3 mtr. @ 0.615 kg/mtr. =
2.03 kg
(ii) 75mm long - 6x11=66.00 nos. x
0.075 = 4.95 mtr. @ 0.615 kg/mtr.=
3.04 kg
Total=2.03 + 3.04 = 5.07 kg
7221 Self-Drilling/Self-Tapping Screws
5.5x25 mm long each 236.00 3.00 708.00
(a) Bracket to vertical profile
- 30 Nos.x2.00 nos. = 60.00 Nos
b) For fixing of brackets to “C”
clamps (22+66=88)x2=176 nos.
Total = 176 Nos + 60 = 236.00 Nos
1007 HDG Mild Steel Brackets (Minimum 80
microns Galvanizing) quintal 0.6358 4950.00 3147.21
a) Wall bracket - 110 x 80x6mm thick
(i) 100 mm long = 10x0.10= 1.00 Mtr
@ 8.65 kg/mtr. = 8.65 kg
(ii) 175mm long = 10x0.175=1.75 mtr.
@ 8.65 kg/mtr. = 15.13 kg
Total = 8.65 + 15.13 = 23.85 kg
b) Corner Bracket of size 220 x
110 x 12mm thick
(a) 100mm long - 5 Nos x0.10
= 0.50 mtr. @ 28.90 Kg/mtr. = 14.45 Kg
(b) 175mm long - 5x0.175= 0.875 mtr.
@ 28.90 kg/mtr. = 25.28 kg
Total = 14.45 + 25.28 = 39.73 kg
Gross total = 23.85+39.73 = 63.58 kg
= 0.6358 quintal
7222 SS Anchor Fasteners (RCC / Brick)
– M-8x100 mm each 30.00 70.00 2100.00
6x5 nos. = 30 Nos Bracket
7390 EPDM Gaskets of size 100x80 mm metre 3.00 15.00 45.00
30x0.10=3.00 mtr.
7218 MS Polymer Sealant Adhesive litre 0.175 1200.00 210.00
Area = 12.60 Sqm + 5% = 13.23 Sqm
Adhesive required = 175 ml. or 0.175 ltr.
7390 EPDM gasket for tiles mounting on
C - clamps metre 8.25 15.00 123.75
(i) 150mm long - 2x11 no. = 22.00 nos.
x 0.15 =3.3 mtr.
(ii) 75mm long - 6x11=66.00 nos.
x 0.075 = 4.95 mtr.
Total = 3.3 + 4.95 = 8.25 mtr.
LABOUR
0166 Installation charges for fixing of façade
at all heights with extruded hollow clay/
terracotta ventillated rain screen tiles sqm 12.60 645.00 8127.00
9999 Carriage of materials L.S. 125.00 2.12 265.00
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2204
Code Description Unit Quantity Rate Amount
9999 T&P and materials Lead & Lift L.S. 250.00 2.12 530.00
TOTAL 48513.06 W
Add 1 % Water charges on "W" 485.13
TOTAL 48998.19 X
Add GST on "X" (multiplying
factor 0.1405) 6884.25
TOTAL 55882.44 Y
Add 15% CPOH on "Y" 8382.37
TOTAL 64264.80 Z
Add Cess @ 1% on "Z" 642.65
Cost of 12.60 sqm. 64907.45
Cost of 1 sqm 5151.38
Say 5151.40
SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 2205
You might also like
- 1-CPWD - DAR - Vol - I - Introductions-Civil 1-90% (1)1-CPWD - DAR - Vol - I - Introductions-Civil 1-927 pages
- Drinking Water & Sanitation Department, Govt of Jharkahnd Schedule of Rates67% (9)Drinking Water & Sanitation Department, Govt of Jharkahnd Schedule of Rates245 pages
- Standard Rate Analysis For Site Specific Items 24.11.2023No ratings yetStandard Rate Analysis For Site Specific Items 24.11.202329 pages
- Analysis of Rate For Delhi - 2012 (Vol - I) .No ratings yetAnalysis of Rate For Delhi - 2012 (Vol - I) .712 pages
- DSR Book Vol 2 2016 (English Version) Final (Full Permission)88% (16)DSR Book Vol 2 2016 (English Version) Final (Full Permission)258 pages
- Constt. of 01 No Watch Towers: Add SICOP Service Charges@6% Total RsNo ratings yetConstt. of 01 No Watch Towers: Add SICOP Service Charges@6% Total Rs6 pages
- 14 Building Works Dismantaling DemolishingNo ratings yet14 Building Works Dismantaling Demolishing5 pages
- Pokhara Sub - Metropolitan City Office: Rate Analysis of Electrical Works (F/Y 2069/070)No ratings yetPokhara Sub - Metropolitan City Office: Rate Analysis of Electrical Works (F/Y 2069/070)10 pages
- Deviation Statement and Rate Analysis For Civil Work100% (1)Deviation Statement and Rate Analysis For Civil Work71 pages
- Tamilnadu SOR 2022 2023 APPROVED Watermark 2100% (1)Tamilnadu SOR 2022 2023 APPROVED Watermark 2177 pages
- Analysis of Rates For Delhi: Central Public Works DepartmentNo ratings yetAnalysis of Rates For Delhi: Central Public Works Department100 pages
- Lecture No. 5 Lime and Liming MaterialsNo ratings yetLecture No. 5 Lime and Liming Materials54 pages
- Influence of Binders On Combustion PropeNo ratings yetInfluence of Binders On Combustion Prope19 pages
- Metal Casting Processes: Manufacturing Processes, 1311 DR Simin Nasseri Southern Polytechnic State UniversityNo ratings yetMetal Casting Processes: Manufacturing Processes, 1311 DR Simin Nasseri Southern Polytechnic State University70 pages
- GTEC Chemical Cleaning, Pressure Testing & Flushing ProcedureNo ratings yetGTEC Chemical Cleaning, Pressure Testing & Flushing Procedure12 pages
- Scratch Test Methodology For Leadframe PlatingNo ratings yetScratch Test Methodology For Leadframe Plating5 pages
- Iia Exporter List: Sr. No. Exporter Id Member Id Unit Name Contact Person District Product Product CategoryNo ratings yetIia Exporter List: Sr. No. Exporter Id Member Id Unit Name Contact Person District Product Product Category2 pages
- The Effect of Hydrated Lime On The Petrography and Strength Characteristics of Illite ClayNo ratings yetThe Effect of Hydrated Lime On The Petrography and Strength Characteristics of Illite Clay10 pages
- Functional thiol ionic liquids as novel interfacial modifiers in SBRHNTs composites-交联密度 PDFNo ratings yetFunctional thiol ionic liquids as novel interfacial modifiers in SBRHNTs composites-交联密度 PDF8 pages
