Car Alarm System [eraerunetion EE Operon as a] In disarming, press @ button once Arm { [arm re In arming, press mf button once Pe Silent arm In disarming, press >= button once, then press @ button ‘once within 38, Silent disarm In arming, press »=button once, then press ff button once within 3s Set arming, ignore shock'| In disarming, press @ button once, then press »= button rem once within 3s Car finder In arming, press @ button once Panic mode Press f@ button and mf button at the same time for 3s Temporary output” Press »=button for 1.5 ‘Shock sensor's _ sensiivit adjustment "Y | turn ACC from ON to OFF, then press @ button for 3s Trunk release Press *button for 2s or press mf button for 3s Activate Anti-hijack mode ACC-ON, press f@ button and »=button at the same time for 2s Features: 1. Arm In disarming, press @@ button once, light flash once, siren sound ‘once, car's door locked, engine locked, power window output for 30s(if F17 setting is’Power window’), LED flash quickly, enter into arming within 3s. 2. Disarm 'n arming, press sf button once, light flash twice, siren sound twice, system disarm, dome light Output for 30s. LED flash quickly, if don't open the door within 30s, LED don't flash, system auto re-arm. ee Escaneado con CamScanner3. Silent arm In disarming, press »=button once, then press f@ button once within 3s, light flash once (si ren don't sound), system arm, 4, Silent disarming P , ress »=button once; then press aff button once within 3s, light flash twice (siren don't sound), system disarm. 5. Car finder In armi f ing, press f@ button once, light flash five times, siren sound five times. 6. Stop alarm When system is triggered, siren sound. Press any button can stop alarm, system keep in arming. 7. Alarm prompt 1) Triggered by slight shock, siren sound quickly five times, parking flash twice. 2) Triggered by heavy shock, siren long sound for 30s, parking light flash for 30s. 3) If triggered by door, trunk or hood, siren long sound for 30s, parking light flash for 30s. 4) Triggered by ACC ON, siren long sound for 30s, parking light flash for 30s. Continue after 5s, until ACC OFF. 8, Auto re-arm (Programming table—F1) ‘After disarming, LED flash quickly. if ACC keep OFF, or don't open door within 30s, system auto re-arm and lock. 9. Passive arm with lock (Programming table—F2, F3) ACC OFF, close all the doors, system passive arm after 60s. Close all the doors, siren sound once after 1, lights flash once, LED flash quickly, indicating count down 60s. When count down, open any door, system stop counting, and start count down again after closing door. i'someone in the car, can cancel the function temporarily: Turn ignition key to ON position then turn to OFF position, LED stop flashing, passive arm stop. open the door and close, count down start again, light lash once. 10. Abnormal arming prompt Itpress &@ button to arm the system when door, hood or t Parking light flash four times, and system enter into arming and stop testing related trigger point, 2 runk don't close, siren sound four times, Escaneado con CamScanneruntil closing well. LED will fash Note: If F10 Som be times then stop one second to indicate it. indication. S “Delay 45s”, when arming, don’t close door, will only LED flash for 1. Shock sensor's sensitivity adjustment Five | /@ levels can be adjusted, factory default is the third level: 41) Tum ignition key to ON position then turn to OFF position, press €@ button for 3s, light keep light indicating enter into adjusting state 10s, siren sound once, confirm choosing level 1 2) Press f@ button again 3) Press @ button again, siren sound twice, confirm choosing level 2...... And level 3, 4, 5 4) Press »=button to confirm choosing, and exit “Shock sensors sensitivity adjustment’ ight stop flash indicating exit. 42. Turn off shock sensor (Programming table—F9) If shock sensor is broken, can cancel sensor function, see Programming table—F9. r temporarily 13. Arm and close senso! 9 .58 f@ button, then press »=button within 3s, siren sound once to ‘Arm and ignore sensor: pre’ indicate. 44,UItrasonic sensor / her arming for 3s, the uirasonic sensor Wil be activated, and ultrasonic sensor will work after 8s, fe, siren sound five times, light flash twice. If ultrasonic sensor is triggered at first tim System is tiggeP 49s, siren sound for 30s, light flash for 30s. triggered again wil nsor or shock sensor nic 21 45.Ignore ultraso" ersten : on or broken, after system keeps armit In arming, if ula tr ore ultrasonic Sensor or shock sensor unt th ps arming for ‘ tem will ig” il them return to normal. six times; § 46,Auto central Jock function ON, press B button will lock, and press af button wil unlock, yn tock programming table—F4) g ‘CC to ON. After 2s, all the doors lock, k: cc ON, Loc! a oats {programming table—F5) a othe myer, all the 400" unlock. A Escaneado con CamScanner17. Trunk release press Mbuton for 2s (orpress wf button for 35), unk Tease, output, ution to release trunk, the System will ignore jy { : i ms ; Note: In arming, press Mbt A closed (the BLUE wire must be connect trigger function until the trun! Sensor ang tun | 18.Engine lock In arming, system will output a signal to lock engine. Or to control ultrasonie Sst ny ing, 19.System memory | ; If power off, system will preserve the memory. When car in anti-iiack moge * power restore power, will keep in anti-hijack mode. Of, step 20.Trigger prompt In arming, if system is triggered, when disarming, siren sound four times and lght fash our imes o remind to check the car. In alarming, LED prompt as the following table, LED only incicates tha highest level of trigger type after disarming, If ACC ON, system will clear arming prompt, Situation LED prompt Slight trigger LED flash quickly twice and stop 1 seconds Heavy trigger or Ultrasonic trigger _| LED flash quickly three times and stop 1 seconds Door, front cover, trunk LED flash quickly four times and stop 1 seconds [ACC trigger LED flash quickly five times and stop 1 seconds \ 21.Open door reminder (Programming table —F18) | __ ACC ON, open door every time, direction lights will flash for 15 times. . 22.Emergency disarm If losing the remote control or in ant 1) Tum ignition key to ON posi 2) Press emergency switch six tim 3) Disarming after 2s, or cancel a es within 10s (The factory default PIN cod? § 6") | inti-hijack mode. | 23.P 1 | Not: -F19" uneteeaneY Password (PIN code) hanged set “ON”, a a | The facing oer lowing Mays. ON": please set “F13” to “OFF” fs hen ‘tory default Pi ; f 1) In disarmin Cods is “6”, can by , wing WAY" hin 78) reg e2M™ing, tum ignition ky n be changed according to the followin! -e-(yitin | Ben give one ong cy, rane)" “ON” to “OFF thre times, and stop” ip, indicatin, i itch N time (ran, it© Programming time © 0 operate, 2) © type a new password, on within 10s, system will exit progr” , a Escaneado con CamScannera . —~ 24.Panic mode ACC OFF, press @ button and af button at the same time for 3s, siren long sound and light flash for 30s, press any button to stop. 25.Remind other car When driving, if you want to overtake, press @ button and aff button at the same time for 38, siren) long sound and light flash quickly for 15s to remind the front driver, press any button fo stop. 26. The second channel, has two output: (Programming table—F'16) 1) Dome light output(-): after disarming, dome light keep lighting for 30s. If set arming or turn ACC. to ON, dome light stop lighting. 2) Horn output(-): need to add a relay. (Programming table—F17) id channel will send a signal for 30s to power el the signal of the third channel. the third channel will send a signal. Stop pressing 27.The third channel, there are two output: 4) Power window: there is a lock signal, the thi window system. Press the second button to canc 2) Temporary output: press »=button over 1.5s, will stop sending. 28. Intelligent anti-hijack function There are three ways to enter into ant ijack mode: 1) Remote control activates anti-hijack: press @ button and »=button at the same time for 2s. (Programming table—F11) jack automatically. 2) ACC ON aativates antiijack: turn ‘ACC to ON, system activates a (Programming table——F"®) 3) Driver's door activates anti (eo —F12) iNet eod0 connect with blue/ white wire.) there are two modes can be chosen (Programming table—F15) jack: ACC ON, open door will activate anti-hijack. (Programming Anti-hijack alarm: AwoalED ash quieky. ight flash quickly twice, sran don't sound (F14 setting is “ON"—siren sound oe sogin kl, LED fash quickly, sn dont sound (F14 setting fs “ON sien wll sound twice) ‘After 605, Site" 1 gound, ght flash, engine is biocked, car lock, light flash twice, siren don't sound (F14 setting is “ON"—siren will ‘—siren wi sound twice) sound, dome light flash at the same time ret ig iron sund, dome light flash at th A ight flash, siren 8K 'e Same time, engine begins kill Escaneado con CamScannerA , ter 60s, siren sound, light flash, engine is blocked, car lock. Exit anti-hijack If want to cancel anti-hijack: 1) Within 59s of anti-hijack, press emergency switch once can exit anti-hijack mode 2) After 60s of anti-hijack, turn ACC to ON, press emergency switch six times (or PIN code), can exit anti-hijack mode after 38 29:Valet mode 1) Turn ACC to ON 2) Press emergency switch for 2s, LED keep light, enter into valet mode 3) Repeat the above operation to exit valet mode 4) In valet mode, press sf button or @ button to unlockilock, but without arming or disarming. 30, Delay detecting door ((Programming table—F10) If dome light keep light, we can set “F10" to “ON” (delay 45s to check the door). When arming, it can avoid reminding door is open every time. When chose “Delay 45s”, after arming: door is open in 46s, after 45s system alarms, siren sound for 30s, light flash 30s. ‘System will continue six cycles. Press any button of remote control can stop alarming, and ignore detecting the door. eumatic lock choosing it-—the time of lock/unlock is 0.5s, $1 open 31.Electric lock/Pn 'e of unlock/lock: S1 short circuit Use $1 to set the tim circuit —the time of lock/unlock is 3.8, Note: setting before system publish a circular, setting is effective after publishing a circular. 32.Remote control learning code 4) Tum ACC to ON 2) Prose emergency switch five times within 3s, siren wil give one long chirp to confirm entering 76 teaming code mode. You have 10s to learn code, if you has no operation or turn ACC to OFF within 10s, system will exit learning code mode, siren will give 2 chirps to confirm. 3) Press any button of the first remote control, siren sound once to confirm learning code successful. 4) Within 10s, press the second remote control, siren sound twice to confirm 8) If the fourth remote control has been learned code, system will exit learning code mode, the siren will give two long chirp to confirm. 33. Resume to the factory default setting state pen any der, tum eco ON within 3s, press emergency switch three times (Note: if F13 " must press emergency switch four times—the first time is to exit anti-hijack), The last time long press for 10s. Siren sound six times, light flash six times, the function of programming table resume to the factory default setting state. Escaneado con CamScanner33. Remote control programming function Note: if F13 setting is “ON”, turn ACC to ON in disarming, and press emergency switch once to exit anti-hijack, and then follow the steps below; if F13 setting is “OFF”, ACC ON then follow the below steps directly to program the function of main box. 1) Tum ignition key to OFF position within 3s, ° 2) Press emergency switch five times within 105, siren wil give one fong chirp , ight fash for 10 times to confirm system has enter into function programming mode; 3) Press emergency switch. If want to change the eighth function, press emergencY ae times, siren sound eight times Siren sound Press time 1-4 short sound 1-4 times 4 long sound 5 times 4) Press @ button or sf button to choose. If press fi button, siren sound once, LED light. If press sf button, siren sound twice, LED don''t light. 5) Repeat step 3, 4, to adjust other function. 6) Turn ACC to ON, or no operation within 10s, exit program, siren sound five time Programming table Press [ button, Press _ button, siren Ne ome siren sound twice, sound once, LED ON Here 7_| Automatic re-arm ON. OFF 2_[ Passive Arm ‘ON. Fi 3 | Passive Arm with lock ON, lock ‘OFF, unlock 4 [AGC ON, Lock ‘ON OEE 5 | ACC OFF, unlock ON. ‘OFF @ | Close door pulse Single pulse Double pulse 7 Open door pulse Single pulse Double pulse 8 | Armidisarm ‘with sound ON OFF ‘9__| Shock sensor ON OFF 40 [Delay detecting door ‘ON (delay 45s) OFF (no delay) | Delay detecting +t Remote control anti-hijack _/ON FE Driver's door active ON GFE 12 anti-hijack 7a [ACG ON active anti-hijack ‘ON OEE Aes into anti-hijack, siren | ON OFF without sound 14 | sound 5 [Enter tnt antliack ‘A mode Bnd +6 the second channel Bome light © tees Laz [he thd cha ind | (On eras & Temporary output (> ‘Open door, light remind | Spock sensor delayed 30s oF [49 Escaneado con CamScanner1. The shadow part is factory default setting. 2. If “F16" choose dome light, and use the second channel to control dome light, suggest F410 choose “ON” 3. If “F17” choose power window, and use the third channel to control power window system, suggest F19 choose “30s” Wiring Diagram Built-in shock sensor Lock/Unlock pulse time is 05 second Sate aaaBIO Emergency Switch Start Killer (-S00ma) SHUN J (© méyno mopuim asojy <— ©) mop swoand Of) ang| ~ = Didang wap WHORE Fei Sara ane (+) sod 04 (© andyno yuna, ©) poor mang | (-) yndyno yy suzog opm, Escaneado con CamScanner 4