Wavence UBT-m 80GHz Quick Start Guide 3DB 28459 AAAA TNZZA

UBT-m 80GHz [1+0] up to 1Gbps [1+0] 1 - 2.5Gbps [1+0] 2.5 – 10Gbps

Optical Optical
Electrical Optical
BNC
Antenna
Alignment
connector
UBT-m 80GHz

PWR 1 2 3 4

Ground point No optical connection

for MSS-0

DC power connector XPIC Port

-48 V (-30V to -57V), Fiber optic: 1G, 2.5G
copper pair or coaxial or 10G optical SFP+
Standalone
coupling/management (other
Electrical data port
Fiber optic data port equipment)
Ethernet Electrical
Ethernet 1G, 2.5G or 10G MSS-O MSS-1 MSS-4/8
PFoE SFP QMA SFP 10G QMA
optical SFP+

Antenna Dual Polar [2+0] XPIC Wavence powering

From Flexi Outdoor Power
2 x UBT-m 80GHz XPIC

From MSS QMA port (EAC)

Distribution Unit

Coaxial cable (DC)

Copper pair cable (DC) EAC 10G

(2 X QMA)
 48 V DC

DATA DC EAC
XPIC cable DATA
DC

SFP 10G QMA SFP 10G QMA

From Outdoor Power Injector

UBT-m 80GHz SFF Steerable pole mount UBT-m on steerable pole mount Power Feed over Ethernet (PFoE)
(OPI)
UBT-m (embedded antenna)

Max 1Gbps

SFF = Small Form Factor

CAT5e cable CAT5e cable

data and DC data and DC

PFoE towards UBT Ports (1, 3)

Data to/from other equipment Ports (2,4) EAC

Up to 2 UBT-m 80GHz can be powered by a
common OPI.
Note: Extended Power Unit (EPU)
can be used for indoor unit.
MSS-1
 Installing Wavence UBT-m 80GHz 3DB 28459 AAAA TNZZA

1 Install UBT-m 80GHz on integrated antenna 2 Install UBT-m 80GHz on

Dual Polar Antenna
3 Install UBT-m 80GHz SFF on steerable mount
1.1 Place the screws in the fixing points depending on the antenna’s polarization. 1.2 Place the UBT. 1.3 Insert UBT, insert the 3.1 Install the steerable
Vertical long screws and tighten. Mount the UBT-m 80Ghz on Dual Polar mount on the pole.
polarization Antenna only as shown in the picture (ports
mH mV pointing in the same direction).
Vertical Polarization Two possible positions for
V and H polarization (see
step 1.2).
mH mV

The V or H mark on top

of the plate indicates the
RFS mounting plate antenna’s polarization. 3.2 Install the UBT-m with
Horizontal its embedded antenna
mH polarization attached to it.
mV Horizontal Polarization
mV mH (H polarization is shown in
Note: Pay attention to the this picture)
positioning pins inside the
Note: Pay attention to the positioning pins
nose receptacle.
Tongyu mounting plate inside the nose receptacle.
Hint: Polarization is indicated
mH: UBT-m on H polarization by the diagonal from the
mV: UBT-m on V polarization power port.

4 Install Flat Panel on UBT-m 80GHz 5 Ground the UBT-m 80GHz 6 Assemble and connect DC
connector
Example of UBT installation with MSS
4.1 Install the UBT-m 80GHz on the steerable mount. 6.1 Assemble the OCTIS DC connector and
Connect the UBT ground point to the
connect the DC cable following the instructions’
UBT-m 80GHz 2 UBT-m 80GHz XPIC on OMT nearest grounding plate using the ground
leaflet.
cable 16mm² 3CC08166AAXX. Washer,
screw and lug are provided with the UBT. .

4.3 Attach the embedded antenna.

6.2 . Plug in to PWR port.

4.2 Attach the interface plate (positioning pin).

Data
Data DC

Data+DC XPIC cable

DC

MSS-8

7 10 Ground the indoor outdoor cables 11 Perform alignment

Assemble and connect
RJ45 connector 8 Assemble and connect
SFP connector 9 UBT-m 80GHz and OCTIS caps
10.1 Install one grounding kit : 11.1 Align the antenna.
7.1 Assemble the RJ45 on the ethernet 8.1 Assemble the OCTIS SFP 9.1 Plug cap of UBT port inside - On top, when it comes on the tower 11.1.1 Plug the BNC-to-banana
cable using the RJ45 tool. connector following the instructions’ SFP 10G QMA adapter on the UBT.
corresponding OCTIS cap. - On bottom, when it leaves the tower
leaflet. - At the entrance of the building
7.2 Assemble the OCTIS RJ45 connector (Either the left or the right BNC may be used.)
following the instructions’ leaflet. SFP 10G QMA
Maximum distance between 11.1.2 Plug the banana plugs into the multi-meter.
2 Grounding Kits: 50m 11.1.3 Adjust the elevation and azimuth to the
Self-amalgamating tape must be used. maximum RSL [lobe number 2 (Main lobe)].
Contact support
9. 2 Attach OCTIS cap with tie-rap
7.3 Plug in to port 1. 8.2 Plug in to port 2 or 3. to UBT lever (photo below) or to To access online customer support (NOLS), go to:
tower. https://online.networks.nokia.com

For product documentatiion:

On the NOLS page, select Sign In/Register (MyAccess) and Line A-A represents azimuth path of a
click on ALU Online Customer Support (OLCS). 10.2 Connect the grounding kit to the properly aligned antenna.
ground plate.
For technical support contact information: 11.2 For XPIC maximize the XPD value shown in
– Grounding kit for Ethernet cable or
On the top right side of the OLCS page, click Contact Support. the craft terminal by polarization alignment.
coaxial cable (Ø 6,85) 1AD040130004
Note: In this way, we avoid losing any Select your country from the drop-down list and click SUBMIT. – Grounding kit for coaxial cable (Ø 10,3) For systems with external OMT: rotate the OMT
caps during maintenance activity. The contact information is displayed. 1AB128500002 on its rotation range.