Wireless Multi-Circuit Monitoring

Revolutionizing multi-circuit monitoring

Packet Power provides a simple, cost-effective way to monitor single- and three-phase circuits
up to 600V and 10,000A. The complete pre-configured monitoring units transmit data from
1 to 72 current sensors using a self-configuring wireless network. All units are built to spec to
make installation fast and easy.

Monitoring Made to Measure

Cuts installation time in half

Comes pre-configured for:

• Voltage service - 100V to 600V AC
• Voltage source quantity
• Voltage lead color and length
• CT type - split core, solid core, or Rogowski coil
• CT ratings - 15A to 10,000A
• CT quantity - varies by model from 1 to 72
• CT lead length
• Distance from monitor to circuits
• Wire exit location and mounting option
• Over-current protection
• Mix of full power and current only monitoring
• Predefined panel circuit maps

BGS16-16P

Monitoring applications

Panelboard Select HVAC, Generators Existing Tenant Data Center

input feeds panelboard and high energy switchgear submetering PUE
circuits loads

© 2020 Packet Power LLC MCM V4

 Wireless Multi-Circuit Monitoring

Multi-Circuit Monitors
• Use full power monitoring to track power and energy
• Use current-only monitoring to lower costs
• Cut installation costs
- “Plug and Play” wireless data network
- No configuration needed on site
- Minimizes number of CT wires to run
- Choose prewired CT harnesses or loose CT leads
• Optional fusing
• Highly compact
• Wireless firmware updates
• Easy panel mapping tool

Access data instantly from the EMX Energy

Monitor cloud service or from existing
monitoring applications using SNMP,
Modbus TCP/IP, Ethernet/IP, BACnet/IP,
BGS32-16P12C
MTConnect, or MQTT

Current Transformers
Split Core CTs Rogowski Coil CTs
Inside Diameter Rated Amperage Inside Diameter Coil Length Typical Amperage
10 mm 15, 30, 50 68 mm 250 mm 100A to 1000A
16 mm 100 147 mm 500 mm 400A to 3000A
24 mm 100, 200, 300 211 mm 700 mm 1000A to 5000A
36 mm 200, 300, 400, 600 306 mm 1000 mm 2000A to 10,000A
50 x 50 mm 400, 600, 800
75x125 mm 300, 600, 800 Solid Core CTs
150x150 mm 800, 1000, 1200, 1600, 2000, 3000, 4000 Inside Diameter Rated Amperage
9 mm 35
Additional current ratings available 15 mm 60

Why Packet Power

Installs easily Cost effective
• Arrives fully configured • Match type and amount of metering
exactly to your needs
• No communication cables
• Lower installation costs
• Access date remotely with no
programming • Fully self-optimizing wireless network
lowers ongoing support costs

Open Secure
• Compatible with any existing hardware • Unique purpose-built wireless protocol
can only be used for monitoring
• Send data to any DCIM or BMS using SNMP.
Modbus TCP/IP, Ethernet/IP, BACnet/IP, • Full separation of wireless monitoring
MTConnect, or MQTT and wired data network
• Proven in data centers worldwide

© 2020 Packet Power LLC MCM V4 - Page 2

 Wireless Multi-Circuit Monitoring

Packet Power Monitor Configurations

100 - 480/277V AC Input Voltage 480V, 600/347V AC Input Voltage
Max Max CT Max Max
Full Power Current Interconnect Full Power Current
Model CTs Only CTs Boards Model CTs Only CTs

BGS16 BGS9H

BGS16-12C - 12 1 BGS9H-3P6C 3 6
BGS16-16P 16 - 1 BGS9H-6P 6 -

160 x 160 x 92 mm
(6.3 x 6.3 x 3.6 in)

BGS32 BGS15H

BGS32-16P12C 16 12 2 BGS15H-3P12C 3 12
BGS32-24P 24 - 2 BGS15H-6P6C 6 6
BGS32-32P 32 - 2 BGS15H-9P 9 -

241 x 160 x 96 mm
(9.5 x 6.3 x 3.8 in)

BGS18H

BGS18H-12P 12 -
BGS18H-15P 15 -
BGS18H-18P 18 -

254 x 305 x 64 mm
(10 x 12 x 2.5 in)

BGS72 BGS27H

BGS72-40P 40 - 3 BGS27H-21P 21 -
BGS72-48P 48 - 3 BGS27H-24P 24 -
BGS72-56P 56 - 4 BGS27H-27P 27 -
BGS72-64P 64 - 4
BGS72-72P 72 - 5

356 x 305 x 64 mm
(14 x 12 x 2.5 in)

For branch circuit monitoring solutions requiring 30 to 198 CTs, go to

www.packetpower.com/panel-board

© 2020 Packet Power LLC MCM V4 - Page 3

 Wireless Multi-Circuit Monitoring

Technical Specifications
Measurement
Measurements Full Power: V, A, Ah VA, W Wh, Power Factor, Hz, THDi, THDv
Current Only: A, Ah
Accuracy ± 1.0% (CT dependent); ± 0.5% available
Input voltage 100-480/277V AC; 480V or 600/347V AC
Input voltage configuration LLLN+E, LLL+E, LLN+E, LN+E, LL+E
Current range 15A to 10,000A
Frequency 50/60 Hz

Communications
Operating frequency 860 to 930 MHz and 2.4 GHz (frequencies vary by region)

Wireless network protocol Frequency hopping self-configuring load-balancing mesh

Wired network protocols HTTPS to Packet Power EMX running locally or as cloud service; SNMP V1/V2c/V3;
Modbus TCP/IP; Ethernet/IP; MTConnect; BACnet/IP; MQTT
Firmware updates Wireless
Typical transmission range 10 to 30 meters indoors between any two devices in mesh network
Antenna Fully enclosed, fixed configuration
Monitoring unit to gateway ratio 10 to 50 BGS units per gateway (depending on model) with unlimited gateways per site
Multi-site support Yes
Encryption HTTPS, optional 128-bit wireless
Local display Volts, Amps, Wh and communications status (varies by model)

Environmental & Mechanical

Operating environment 0° to 75°C (32° to 167°F); 5% to 95% non-condensing
Water and dust resistance NEMA 1/IP20 (indoor use); NEMA 4 available on some products
Power usage 1-7W depending on the product
Certifications UL 508A and CE, FCC and other communication standards

For detailed product specifications, go to: www.packetpower.com/multi-circuit-monitoring

Secure Wireless Technology

Proven in critical facilities worldwide
Packet Power’s wireless protocol was designed specifically for critical facilities. The unique protocol is different
than WiFi or Zigbee and can only be used for monitoring. It allows for a complete separation of the wireless
monitoring network from the wired data network. It is proven to work in data centers and other critical facilities
run by major financial services firms, government agencies, educational institutions, telcos and colos worldwide.

2716 Summer St. NE Ph +1 (877) 560-8770

Minneapolis, MN 55413 Fax +1 (866) 324-2511
USA www.packetpower.com

© 2020 Packet Power LLC MCM V4 - Page 4