Cross Country Wireless Ltd, 7 Thirlmere Grove, BOLTON, BL4 0QB, UK Email [email protected] Web page http://www.crosscountrywireless.

net Telephone +44 (0) 1204 410626 Mobile +44 (0) 7752 391908

APRS TNC Digi Tracker USB version Operating Manual

version 1.9

Directors: Mr C.J.Moulding, Mrs S.M.Moulding Company no 7431559 registered in England and Wales

Contents
1 2 3 4 5 6 7 8 9 10 11 12 13 What is APRS? APRS TNC Digi Tracker Connections, switches and deviation adjustment Windows set-up Configuration with a Serial Terminal program Mobile configuration for GPS mode Internal GPS receiver information Fixed station configuration for Terminal mode Use with a Serial Terminal program Use with UI-View Use with WinPack Fill-in digipeater option Digipeat ALL option Tracker Manifesto by Bob Bruninga WB4APR, the inventor of

Appendix 1 APRS Appendix 2 Appendix 3 Appendix 4

TNC text commands APRS icon codes Acknowledgements

What is APRS?

APRS stands for Automatic Packet Reporting System. It was invented by Bob Bruninga, WB4APR in the early 1980's initially to track local mobile stations. It is based on the AX.25 packet radio system but used the unconnected mode to send positions, information and messages to all stations. Today it is widely used by amateur radio emergency communication networks throughout the world as a tactical emergency communications system of tremendous capability that allows local APRS networks to be viewed worldwide via internet gateways. It can also be used on HF and via satellite. An APRS digipeater is installed on the International Space Station and regularly re-transmits APRS packets from earth-bound stations. More information taken from Bob Bruninga's website http://aprs.org APRS provides situational awareness to all operators of everything that is going on in his local area, whether it be Weather reporting, traveller information, direction finding, objects pointing to Echolink or IRLP or traffic reporting and emergency response. All of this while providing not only instantaneous operator-to-operator keyboard messaging capability for special events but also an always-on Voice Alert back channel between mobiles in simplex range. There is even an APRS interface to the WinLINK system called APRSlink so that mobiles can send and receive Email without needing a PC. Think of APRS as a signalling channel to reveal ALL amateur radio resources and live activities that are in range of the operator at any instant in time. Consistent with providing information on all resources within range, APRS must also work across all boundaries and in all areas of the world for all travellers. For this reason, 144.800 MHz is dedicated to APRS throughout Europe. Other continents have similar single frequencies such as 144.390 MHz in North America and 145.175 MHz In Australia. Also after 14 years of evolution, APRS was greatly simplified beginning in 2004 to eliminate obsolete and inefficient routing. Now, there is only one recommended PATH everywhere, and it is VIA WIDEn-N for fixed stations where N is usually 2 in most metropolitan areas and no more than 3 most everywhere else. Mobiles can use VIA WIDE1-1,WIDE2-1 in those 2 hop areas to gain help from nearby WIDE1-1 fill-in digipeaters.

Cross Country Wireless APRS TNC Digi Tracker

At the 2008 UK RAYNET National Convention at Liverpool I was part of a small group giving a presentation on the latest developments in APRS (Automatic Packet Reporting System). As always at events such as the Convention the feedback from those attending the presentation was invaluable. Many RAYNET members had simple APRS trackers but wanted to upgrade to the next level where they could use APRS with a computer using UI-View or similar programs or operate a fill-in digipeater from home or from the car. The only hardware option at the time was to buy an old packet radio TNC (rarely available working these days) or to buy an expensive new product. The feedback from RAYNET members was that a simple to use low cost unit with basic TNC, digipeater and tracker facilities would be welcomed. After nine months research, development and testing the APRS TNC Digi Tracker is available for sale. The hardware has been designed for easy field operation with eight switches for power, mode, configuration and digipeater control and six LEDs to indicate correct operation. High performance audio filtering has been added to filter the receive audio. Extensive RFI suppression is employed. High quality components have been used to extend the working temperature range and life of the TNC. As an example metal film resistors are used throughout and the voltage regulator operates at 10% of it's maximum current rating even when powering a GPS receiver through the serial port. The APRS TNC Digi Tracker meets the requirements of EC Directives EN50082-1 EMC Generic Immunity Standard (Residential, Commercial and Light Industrial), RoHS (Restriction of Hazardous Substances) and WEEE (Waste Electrical and Electronic Equipment). The firmware has been developed to add APRS features and improve reliability. The features include a unique Digi All digipeater feature, compatibility with UI-View, compatibility with WinPack for converse packet radio, improved digipeater operation, fast text entry, simple configuration with a serial terminal program and position / status beaconing in GPS mode. Firmware reliability has been designed for use with poor or intermittent power supplies by employing the microcontroller on-chip power up, brown out and crystal oscillator timers. In addition a two second power up delay has been added to ensure that the power supply is stable before reading from the EEPROM. Write and code protection has also been added to avoid any possibility that an intermittent power supply could corrupt the firmware program or configuration data. The USB version uses the well regarded FTDI USB chip to provide a reliable USB connection. Extensive hardware and firmware testing has taken place to prove the TNC reliability. Like the earlier serial port versions, the USB prototypes have survived 2m drops onto concrete floors, freezing to -35 degrees Centigrade, heating to + 60 degrees Centigrade, being installed in a Land Rover off road competition vehicle during several events and just driving to the shops in the family car! I hope you enjoy using the APRS TNC Digi Tracker! 73, Chris Moulding, G4HYG

Connections, switches, deviation adjustment and specification

DB9 Male RADIO

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Transmit audio out No connection PTT out No connection Receive audio in Ground (negative earth only) + 7 to 28 V in No connection No connection The USB Digi Tracker can also be powered via the USB socket with a PC or netbook.

Pin numbers viewed looking into the connectors on the unit.

DIL switch
Switch 1 2 3 4 5 6 7 8 OFF Power off (radio port only) Terminal operation No PTT output (RX only) No PTT output on audio GPS receiver OFF Not used Transmit audio low level Digipeater off ON Power on (radio port only) GPS Tracker operation PTT output on PTT output on audio (HT) GPS receiver ON Not used Transmit audio high level Digipeater on (if DIGI ON or DIGI ALL selected)

Deviation Adjustment
The transmit audio output is adjusted by the sealed cermet potentiometer on the circuit board. Start adjustment with switch S7 in the OFF position. If the unit is in Terminal mode connected to a PC running a terminal program typing CAL will operate the transmitter PTT and send a continuous audio output. The tone can be toggled between high and low tone using the Space bar. Enter Ctrl-C to close the Calibration mode and release the transmitter PTT. Set the deviation using high tone (2200 Hz) because pre-emphasis in the transmitter will make this louder than the low tone (1200 Hz). The deviation should be set so that it is below the clipping level of the audio clipper in the transmitter. If the adjustment is done without a deviation meter listen to the high tone audio received using another receiver adjust until the audio limits and then back off from that. It is far better better to transmit at a low deviation than to over-drive the transmitter with the risk of spurious emissions to adjacent radio channels. If a high audio level is required for certain models of transceiver then switch S7 ON.

Specification
Size: 142 mm (5.6) length 110 mm (4.4) wide 35 mm (1.4) high Supply voltage: Supply current: 7 to 25 volts DC negative earth 35 mA (at 13.8 V) 100 mA with internal GPS receiver (at 13.8 V)

Windows set-up

Before connecting the Digi Tracker to your PC, download the USB driver for your operating system from the CD-ROM supplied or from the FTDI website: http://www.ftdichip.com/Drivers/VCP.htm Connect the Digi Tracker to the PC via the USB cable. Allow the new hardware set-up to run and when prompted select the location of the USB driver. The set-up will then continue. When the Digi Tracker is successfully installed on the PC check the comm port that has been selected by the PC. To do this (this example is Windows XP) Right click on "My Computer" Select "Manage" Select "Device Manager" Select "Ports (COM & LPT)" Open the USB Serial Port for the USB Digi Tracker Select the "Port Settings" tab Change the data speed to 4800 bits per second. Click on "Advanced" Change the Comm port number to a value used by UI-View or APRS Messenger (COM10 as an example) Click OK Click OK Close Device Manager Open APRS Messenger or UI-View Set the TNC baud setting to 4800 bd Set the TNC port to COM10 (in this example).

Configuration with a Serial Terminal program

The APRS TNC Digi Tracker can be configured by any personal computer using Microsoft Windows with a serial terminal program e.g. Hyper Terminal or Tera Term Pro or with a Linux personal computer using the Cutecom serial terminal program. The terminal program set-up table follows: Baud rate Data bits Stop bits Handshaking Host mode Parity Comm Port 4800 or 9600 bd depending on the TNC firmware 8 1 None None None The serial port that the TNC is connected to

When the APRS TNC Digi Tracker is powered up in Terminal mode (switch 2 set to Terminal mode or OFF) the following command text should be seen: cmd: The full list of TNC terminal commands is listed in Appendix 2 TNC Text Commands. The HELP text file showing typical commands follows: cmd: help Commands are case insensitive Use backspace key (<--) for correction Use the DISP command to display all options Switch 2 ON and connect to GPS for APRS tracker operation Switch 2 OFF and connect to terminal for command interpreter Commands (with example): MYCALL (mycall g4hyg-9) UNPROTO (unproto aprs v wide3-3) - Fixed station APRS unproto UNPROTO (unproto gpsc30 v wide1-1 v wide2-2) - Mobile station APRS unproto UNPROTO (unproto aprs v ariss v sgate v wide2-2) - ISS APRS unproto BTEXT (btext >Chris in Bolton) - beacon comment - 100 chars max BEACON (beacon every n)- n=0 is off and 1<n<60 mins MONitor (mon all, mon me, or mon off) DIGIpeat (digi all or digi on) switch 8 digi off) MYALIAS (myalias wide1-1) for fill-in digipeater PERM (to store set-up in EEPROM) ECHO (echo on or echo off) TXDELAY (txdelay n 0<n<201 n is number of delay flags to send) CAL (calibrate mode - testing only) CONV (converse mode - Ctrl C to exit) OK cmd:

Mobile GPS mode configuration

The main list of setup commands is displayed by typing DISP at the :cmd prompt in Terminal mode (switch 2 set to Terminal or OFF). Note that all text commands are case insensitive. During configuration the digipeater switch 8 should be ON to allow the digipeater function to be selected. After configuration the settings should be permanently saved to EEPROM using the PERM command. Set switch 2 set to GPS or ON before installation in the vehicle. A typical mobile configuration using GPS mode follows: cmd: disp ECHO ON TXDELAY 64 GPS GPRMC MONitor ALL DIGIpeater ON - fill-in digipeater BEACON On EVERY 3 UNPROTO GPSC86-0,WIDE1-1,WIDE2-2 MYCALL G4HYG-9 MYALIAS WIDE1-1 BTEXT >Chris testing new TNC firmware... OK cmd: ECHO ON allows typed text to be displayed on the terminal screen. TXDELAY has a default setting of 40. That number is the number of idle bytes sent before the APRS frame after the PTT is keyed. At 1200 bd that works out at 6.6 mS per byte so the default setting gives a delay of 260 mS. The maximum delay setting of 200 gives a delay of 1.33 seconds. The GPS NMEA GPRMC string is selected as default. GPGGA is an alternative option. The GPS NMEA string is transmitted as the APRS information string. This gives far greater position accuracy (typically +/- 1m under 2009 GPS conditions) than the standard APRS position format (+/- 18.5m) or the compressed format (+/- 3m). This is very useful when used with various modern internet tools using Google Maps where the inaccuracy of the other methods becomes readily apparent. Another reason for the use of the GPS NMEA string is that in many countries it is a condition of the amateur radio licence that no coded messages are transmitted. The standard APRS position format and the compressed format can be considered to be coded messages and may be illegal in those countries. The GPS NMEA string is an internationally recognised format and is transmitted unmodified. The string selected may be any one of three. The table below gives further details:

GPS NMEA string GPGGA GPRMC

Length 65 68

Information carried Time, validity, latitude, longitude, fix quality, satellites tracked, HDOP, altitude above the geoid (m), geoid (m) Time, validity, latitude, longitude, speed (knots), track angle, date, magnetic variation

The GPRMC string is chosen as the default as the date, time and speed are also included. MONItor defaults to ALL in GPS mode to allow other programs and attachments to translate the received APRS packets into GPS waypoints. DIGI ON will allow the APRS TNC Digi Tracker to digipeat other mobile stations with myalias WIDE1-1 in their unproto if MYALIAS is set to WIDE1-1. DIGI ALL is a unique option in the APRS TNC Digi Tracker. Any APRS packet received with a valid digipeater unproto setting is digipeated with call substitution. This is intended for two uses. The first is for emergency work. For example a mobile operator could have DIGI ALL configured in the TNC but switched off with switch 8. In an emergency he/she drives up to the local hilltop turns switch 8 on and digipeats all local APRS traffic to the emergency control station. The second use is to digipeat all traffic on a specific channel to the main APRS channel. This could be traffic on an emergency channel, ISS traffic on 145.825 MHz (as long as no satellite operator is within range) or in a recent (April 2009) example to digipeat an APRS tracker on a trans-atlantic balloon on the US APRS frequency of 144.390 MHz to the European APRS frequency of 144.800 MHz. DIGI OFF turns the digipeater off. Switch 8 can switch the digipeater manually to OFF if DIGI ON or DIGI ALL is set. The orange LED confirms that DIGI ON or DIGI ALL is on if selected. The APRS TNC Digi Tracker is firmware configured to send a status packet every 5 position packets when in GPS mode. If the beacon timing is set to BEACON EVERY 3 then the position packet is sent every 3 minutes with the status packet sent every 15 minutes. This complies with the net cycle time concept in the APRS specification. As the APRS symbol is not included in the position packet an alternative method using the AX.25 destination address in the UNPROTO is used. This method uses GPSCnn for primary symbols and GPSEnn for the secondary symbols. In the example above GPSC86 is a van. Other examples are GPSC30 car, GPSC59 pedestrian, GPSC74 jeep and GPSC85 truck. The APRS symbols are listed in APPENDIX 3 APRS symbol table. Optional GPSxyz settings for symbols with overlays are also included. The UNPROTO should also include the digipeater aliases WIDE1-1,WIDE2-2 to allow transmitted packets to be digipeated by the local APRS digipeater network. WIDE1-1,WIDE2-2 is now internationally agreed as the recommended mobile unproto settings used worldwide. In some countries like the UK with a limited digipeater and internet gateway network the settings can be increased up to WIDE1-1,WIDE7-7 to extend RF coverage via digipeater. RELAY and TRACE unproto settings are now obsolete worldwide. Use MYCALL to configure your own callsign and SSID. No SSID or SSID -0 is a fixed station. -7 is a hand portable and -9 is a mobile. MYALIAS is usually set to WIDE1-1 to digipeat mobile stations with a matching digipeater alias when DIGI ON is set. In GPS mode the BTEXT is sent as a status beacon. The status text should always start with a > APRS data type identifier i.e. BTEXT >Chris in Bolton The status text can be up to 62 characters long.

Internal GPS receiver information

The receiver is powered from switch 5. To use the internal GPS for APRS tracking turn switch 2 and switch 5 ON. To use as a TNC turn switch 2 and switch 5 OFF. To feed GPS NMEA data to a PC connected to the USB port turn switch 2 OFF and switch 5 ON.

The GPS receiver is based on the SiRF Star III architecture. It can track up to 20 satelites and use EGNOS or WAAS GPS correction. LED display status: LED ON when power is connected, LED flashing while searching for satellites and LED is permanently on when a position fix is available.

Fixed station Terminal mode configuration

The main list of setup commands is displayed by typing DISP at the :cmd prompt in Terminal mode (switch 2 set to Terminal or OFF). Note that all text commands are case insensitive. During configuration the digipeater switch 8 should be ON to allow the digipeater function to be selected. After configuration the settings should be permanently saved to EEPROM using the PERM command. A typical fixed station configuration follows: cmd: disp ECHO ON TXDELAY 64 GPS GPRMC MONitor ALL DIGIpeater ON - fill-in digipeater BEACON On EVERY 15 UNPROTO APRS-0,WIDE3-3 MYCALL G4HYG-0 MYALIAS WIDE1-1 BTEXT =5332.76N/00225.91W-Chris in Bolton OK cmd: ECHO ON allows typed text to be displayed on the terminal screen. TXDELAY has a default setting of 40. That number is the number of idle bytes sent before the APRS frame after the PTT is keyed. At 1200 bd that works out at 6.6 mS per byte so the default setting gives a delay of 260 mS. The maximum delay setting of 200 gives a delay of 1.33 seconds. The GPS NMEA GPRMC string is selected as default but is not used in Terminal mode. MONItor may be set to OFF (nothing sent to the terminal), ME (just packets addressed to mycall or myalias) or ALL (all packets received sent to terminal). DIGI ON will allow the APRS TNC Digi Tracker to digipeat mobile stations with digipeater alias WIDE1-1 in their unproto if MYALIAS is set to WIDE1-1. DIGI ALL is a unique option in the APRS TNC Digi Tracker. Any APRS packet received with a valid digipeater unproto setting is digipeated with call substitution. This is intended for two typical uses. The first is for emergency work. For example a fixed operator could have DIGI ALL configured but switched off with switch 8. In an emergency he/she diverts turns switch 8 on and digipeats all local APRS traffic to the emergency control station. The second use is to digipeat all traffic on a specific channel to the main APRS channel. This could be traffic on an emergency channel, ISS traffic on 145.825 MHz (as long as no satellite operator is within range) or in a recent (April 2009) example to digipeat an APRS tracker on a trans-atlantic balloon on the US APRS frequency of 144.390 MHz to the European APRS frequency of 144.800 MHz. DIGI OFF switches the digipeater off. Switch 8 can switch the digipeater manually to OFF. The orange LED confirms that DIGI ON or DIGI ALL is on or off. BEACON EVERY is set to 15 so that a beacon is sent every 15 minutes. BEACON EVERY 0 turns the beacon off.

The unproto is set to an AX.25 destination address of APRS with a digipeater unproto setting of WIDE2-2. WIDE2-2 is now internationally agreed as the recommended fixed station unproto settings. In some countries like the UK with a limited digipeater and internet gateway network the settings can be increased to WIDE7-7 to extend RF coverage via digipeaters. RELAY and TRACE settings are now obsolete worldwide. Use MYCALL to configure your own callsign and SSID. No SSID or SSID -0 is a fixed station. -7 is a hand portable and -9 is a mobile. MYALIAS is usually set to WIDE1-1 to digipeat mobile stations with a matching digipeater alias when DIGI ON is set. In Terminal mode BTEXT is transmitted as an APRS information field. In the following example the position is encoded as degrees and decimal minutes (to two decimal places) with a N/S or E/W character. The position accuracy is +/- 18.5m. BTEXT =5332.76N/00225.91W-Chris in Bolton The initial character can be either = to show messaging possible or ! to show that messaging is not possible. The character between latitude and longitude is either / for primary symbols or \ for secondary symbols. The character after the longitude direction (in this example W) is which is the primary APRS symbol for Home (VHF station). A full list of APRS symbols is included in Appendix 3 APRS symbol table. The text following the APRS symbol is comment text up to a maximum of 43 characters.

Use with a Serial Terminal program

The APRS TNC Digi Tracker works in Terminal mode with a serial terminal program. Move Switch 2 to the TNC (off) position. The TNC should be connected to the PC with a USB cable In the serial terminal program select the following options: Baud rate Data bits Stop bits Handshaking Host mode Parity Comm Port 4800 bd 8 1 None None None The serial port that the TNC is connected to

Incoming APRS packets will be displayed in the serial terminal program. A typical fixed station configuration demonstrating APRS messaging using a serial terminal program is shown below: cmd: disp ECHO ON TXDELAY 64 GPS GPRMC MONitor ALL DIGIpeater OFF BEACON On EVERY 15 UNPROTO APRS-0,WIDE3-3 MYCALL G4HYG-2 MYALIAS WIDE1-1 BTEXT =5332.76N/00225.91W-Chris in Bolton OK cmd: conv :mb7ubn :Test 123 G4HYG-2>APRS,MB7UBN*,WIDE3-2<UI>::mb7ubn :Test 123 MB7UBN>APU25N<UI>::G4HYG-2 :Test 123 received{03 The TNC is placed in Converse mode by typing CONV followed by Enter. The message format for unacknowledged messages consists of: : followed by nine character field for the addressee callsign followed by : followed by the message text. In the example the callsign is six characters long and three spaces are typed to fill in the remainder of the nine character field. The message text can be up to 67 characters long. In the example :mb7ubn :Test 123 is typed in followed by Enter. G4HYG-2>APRS,MB7UBN*,WIDE3-2<UI>::mb7ubn :Test 123 shows the transmitted packet digipeated by the MB7UBN digipeater.

MB7UBN>APU25N<UI>::G4HYG-2 :Test 123 received{03 is a message reply sent by the operator at MB7UBN indicating that the test message was received. Control-C closes Converse mode and returns to Command mode.

10

Using with UI-View

The APRS TNC Digi Tracker works in Terminal mode with UI-View. Move Switch 2 to the TNC (off) position to select Terminal mode. The TNC should be connected to the PC with a USB cable. Move the file ccw_tnc.cmd from the CD disc or downloaded from the Cross Country Wireless website into the CMD folder in UI-View. In a typical UI-View installation the CMD folder is found in Program Files / Peak Systems / UI-View32 / CMD In UI-View Comms Setup select the following options: Baud rate Data bits Stop bits Handshaking Host mode Parity TNC Type Comm Port 4800 bd 8 1 None None None CCW_TNC The serial port that the TNC is connected to

When UI-View boots up it will temporarily over-write the settings permanently stored in the TNC with the settings from UI-View Station Setup. If power is interrupted to the TNC during operation the TNC will reboot with it's original permanent settings. If it is planned to run the TNC with UI-View for a long period we recommend that the user sets the TNC configuration and UI-View Station Setup to the same settings to avoid re-boot changes due to power outage. UI-View puts the TNC into Converse mode so that any text sent from UI-View is transmitted by the TNC using the MYCALL and UNPROTO settings previously temporarily set in the TNC by UI-View. If there is a power outage to the TNC it will re-boot into Command mode. UI-View should recognise the cmd: prompt sent by the TNC and send the CONV command to re-set it into Converse mode. If the user wants to re-set the TNC manually in UI-View then open Terminal and click the Conv button. In the configuration file the digipeater function of the TNC is enabled as a fill-in digipeater (as long as MYALIAS is set to the recommended setting of WIDE1-1). The digipeater can be switched on and off manually independently of UI-View by switch 8 on the TNC.

11

Using with WinPack

The APRS TNC Digi Tracker works in Terminal mode with WinPack. Move Switch 2 to the TNC (off) position to select Terminal mode. The TNC should be connected to the PC with a USB cable. In WinPack Options / Comms Setup select the following options: Baud rate Data bits Stop bits Handshaking Host mode Parity DCD show con Comm Port 4800 bd 8 1 None None None No The serial port that the TNC is connected to

Before use with WinPack the TNC UNPROTO should be set to CQ,WIDE1-1,WIDE2-2. The TNC should be set to converse mode by typing CONV followed by Enter. The WinPack program will now work in unconnected mode with the TNC.

12

Fill-in digipeater

DIGI ON will allow the APRS TNC Digi Tracker to digipeat mobile stations with a digipeater alias WIDE1-1 in their unproto. In order for the digipeater to function MYCALL, MYALIAS and DIGI ON need to be configured. MYALIAS should be set to WIDE1-1 to digipeat mobile stations with a matching digipeater alias. DIGI OFF will switch the digipeater off. Switch 8 can switch the digipeater manually to OFF when DIGI ON is selected. The orange LED confirms that the digipeater is operating if DIGI ON or DIGI ALL is selected.

12

DIGIpeat ALL

DIGI ALL is a option unique to the APRS TNC Digi Tracker. Any APRS packet received with a valid digipeater unproto setting is digipeated with call substitution. This is intended for two typical uses. The first is for emergency work. For example a mobile operator could have DIGI ALL configured but switched off with switch 8. In an emergency he/she drives up to the local hilltop, turns switch 8 on and digipeats all local APRS traffic received to the emergency control station. The second use is to digipeat all traffic on a specific channel to the main APRS channel. This could be traffic on an emergency channel, ISS traffic on 145.825 MHz (as long as no satellite operator is within range) or in a recent (April 2009) example to digipeat an APRS tracker on a trans-atlantic balloon using the US APRS frequency of 144.390 MHz to the European APRS frequency of 144.800 MHz. In order for DIGIpeat ALL to function MYCALL, MYALIAS and DIGI ALL need to be configured. DIGI OFF will switch the digipeater off. Switch 8 can switch the digipeater manually to OFF if DIGI ON or DIGI ALL is selected. The orange LED confirms that the digipeater is operating if DIGI ON or DIGI ALL is selected. The sample text below shows DIGI ALL in operation: cmd: disp ECHO ON TXDELAY 64 GPS GPRMC MONitor ALL DIGIpeater ALL - DIGIPEAT EVERYTHING! ARE YOU SURE? BEACON On EVERY 15 UNPROTO APRS-0,WIDE3-3 MYCALL G4HYG-2 MYALIAS WIDE1-1 BTEXT =5332.76N/00225.91W-Chris in Bolton OK cmd: G1AAA>APU25N,MB7UBN*<UI>:;TRAFFIC *051408z5336.11N\00250.53W?10 In 10 Minutes G7HHH>APU25N,G1EUH,MB7UBN,WIDE2*<UI>:=5349.81N/00302.47W-g7hhh@???.com GX0ZZZ>APU25N,G4HYG-2*<UI>:=5322.16N/00201.36WK {UIV32} M0AAA>APU25N,G4HYG-2*<UI>:=5332.30N/00237.13W- {UIV32N} M0AAA>APU25N,G4HYG-2*<UI>:>051410zUI-View32 V2.03 M0AAA>APU25N,G4HYG-2*<UI>:?APRS? MB7UBN>APU25N,G4HYG-2*<UI>:=5332.76N/00225.91W&2m digi + 2m/30m igate Bolton GX0ZZZ>APU25N,G4HYG-2*<UI>:=5322.16N/00201.36WK {UIV32} The text after the DISP command shows typical fixed station operation using DIGI ALL. The first two APRS packets from G1AAA and G7HHH (original callsigns changed) shows that all digipeater unproto aliases have been used previously by other digipeaters and the packet is therefore NOT digipeated.

The remaining six APRS packets in the example have valid digipeater aliases and are digipeated with call substitution (in this example G4HYG-2*). This also stops the packets received being digipeated by other digipeaters. The DIGI ALL option is intended for emergency use only or to digipeat all traffic on a radio channel to the main APRS frequency.

Appendix 1

Tracker Manifesto

APRS TRACKER Manifesto: Welcome to APRS! Bob Bruninga, WB4APR

See website http://aprs.org

Thank you for investing in this exciting aspect of the Ham radio hobby. You will find APRS as a great real-time communications and information distribution system that keeps everyone informed of all surrounding APRS and other Ham Radio activity and that also facilitates communications by data and voice among all members of the APRS network. In that regard, APRS was intended to be a two-way communications system between operators. Although you have purchased an APRS Tracking Device which is sometimes connected to only a transmitter, you can still fully participate as an operator in the APRS net. The best way to do that is to connect your APRS tracking device to a transceiver and although the receiver is not used for data, the receiver and speaker with a CTCSS tone can still be fully used as an APRS intercom channel for back-channel voice coordination and radio-proximity detector. In effect, you get dual use out of the radio (Data and Voice)! As noted on the web page above, placing the frequency of your voice receiver in the Beacon Text of your tracker, everyone that receives your position report can also then see how to contact you, and include you in the voice net as needed. If you use the proper format then your frequency will show up properly on everyone elses displays such as shown here. This way, other operators can then easily tune to your calling channel and make needed contact. Although any voice calling channel can be used, we recommend using a radio with CTCSS-100 and tuned to the APRS data channel (144.39 in the USA, 144.800 in Europe). This way, your speaker is muted to all packets, yet you can be called by voice by anyone using PL-100. Another advantage of this method, is that your speaker also becomes a radio proximity detector to other similar mobiles in simplex range. This is called Voice Alert. Including your own voice monitoring frequency in all of your packets is just part of the use of the APRS frequency parameter. Under the New-N Paradigm, the locally recommended voice repeater for all travellers is also being transmitted by most digipeaters as an object. This informs travellers in the area, what frequency is useful to them right there, right now. These objects show up in the station list of all APRS stations for easy visibility as shown above. If your tracker device has its own transmitter and no receiver, you can still include your monitoring voice contact frequency in a periodic beacon to facilitate communications with you even if you are not onboard. If not a frequency, you might consider including your email address instead. If not in every packet, then once every 10 minutes is suggested. Both of these methods, Voice Alert and local Frequency Objects fulfil the objective in APRS of facilitating communications between all operators in any situation. Enjoy! Bob, WB4APR

Appendix 2
BEACON EVERY BTEXT CAL

TNC text commands

Set beacon timing from 1 to 60 mins. BEACON EVERY 0 is beacon off. Status text i.e. BTEXT >Chris in Bolton Keys transmitter with permanent tone for transmitter FM deviation adjustment. Use Space bar to toggle between high and low tones. Start Converse mode Exit Converse mode or Exit CAL mode Digipeat ALL received APRS packets with a valid digipeater alias Fill-in digipeat digipeats all WIDE1-1packets received Digipeater off (Switch 8 can also switch the digipeater off if DIGI ALL or DIGI ON are selected). Turn on echoed typed text to screen Turn off echoed typed text to screen Select GPGGA GPS NMEA data string for position packet in GPS mode Select GPRMC GPS NMEA data string for position packet in GPS mode Display HELP file in Terminal mode Send ALL received packets to GPS / Terminal port Send received packets addressed to mycall or myalias to GPS / Terminal port Send no received packets to GPS / Terminal port TNC digipeater alias (typically WIDE1-1 for fill-in digipeater) i.e. MYALIAS WIDE1-1 Your callsign and SSID I.e. MYCALL G4HYG-9 Store settings permanently in the EEPROM Re-boot TNC (for use by UI-View on closing program) TXDELAY has a default setting of 40. The number is the number of idle bytes sent before the APRS frame after the PTT is keyed. At 1200 bd that works out at 6.6 mS per byte so the default setting gives a delay of 260 mS. The maximum delay setting of 200 gives a delay of 1.33 seconds. APRS AX.25 destination address and digipeater settings. Typical options: Mobile Fixed ISS unproto GPSC30,WIDE1-1,WIDE2-2 unproto APRS,WIDE3-3 unproto GPSC30,ARISS,SGATE,WIDE2-2

CONV Ctrl C DIGI ALL DIGI ON DIGI OFF

ECHO ON ECHO OFF GPS GPGGA GPS GPRMC HELP MON ALL MON ME MON OFF MYALIAS

MYCALL PERM RESTART TXDELAY

UNPROTO

Appendix 3

APRS symbol tables

Alternate symbol table
Icon Police, Sheriff \ ! \ GPSxyz OBz GPSEnn 01 Emergency Icon

Primary symbol table

/ / ! GPSxyz BBz GPSCnn 01

BCz

02

(reserved)

OCz

02

(reserved)

/ #

BDz

03

Digi green star white centre Phone

\ #

ODz

03

Digi green star (with overlay) Bank or ATM

/ $

BEz

04

\ $

OEz

04

/ %

BFz

05

DX cluster

\ %

OFz

05

Power plant (with overlay) Gateway (with overlay)

/ &

BGz

06

HF gateway

\ &

OGz

06

/ '

BHz

07

Small aircraft

\ '

OHz

07

Incident site (with overlay) Cloudy

/ (

BIz

08

Mobile satellite ground station Wheelchair

\ (

OIz

08

/ )

BJz

09

\ )

OJz

09

Firenet MEO

/ *

BKz

10

Snowmobile

\ *

OKz

10

Snow

/ +

BLz

11

Red Cross

\ +

OLz

11

Church

/ ,

BMz

12

Boy Scouts

\ '

OMz

12

Girl Scouts

/ -

BNz

13

House QTH (VHF)

\ -

ONz

13

House (HF)

/ .

BOz

14

\ .

OOz

14

Indeterminate position

/ /

BPz

15

Dot

\ /

OPz

15

Waypoint or destination

/ 0

P0z

16

Numerical circle 0

\ 0

A0z

16

Circle (with overlay)

/ 1

P1z

17

Numerical circle 1

\ 1

A1z

17

Not used

/ 2

P2z

18

Numerical circle 3

\ 2

A2z

18

Not used

/ 3

P3z

19

Numerical circle 4

\ 3

A3z

19

Not used

/ 4

P4z

20

Numerical circle 4

\ 4

A4z

20

Not used

/ / 5

GPSxyz P5z

GPSCnn 21

Icon Numerical circle 5

\ \ 5

GPSxyz A5z

GPSEnn 21 Not used

Icon

/ 6

P6z

22

Numerical circle 6

\ 6

A6z

22

Not used

/ 7

P7z

23

Numerical circle 7

\ 7

A7z

23

Not used

/ 8

P8z

24

Numerical circle 8

\ 8

A8z

24

Network nodes (with overlays) Petrol station

/ 9

P9z

25

Numerical circle 9

\ 9

A9z

25

/ :

MRz

26

Fire

\ :

NRz

26

Hall

/ ;

MSz

27

Camp site

\ ;

NSz

27

Park / Picnic area

/ <

MTz

28

Motorcycle

\ <

NTz

28

NWS advisory (gale flag) (with overlays) APRS Touch Tone user

/ =

MUz

29

Railway Engine

\ =

NUz

29

/ >

MVz

30

Car

\ >

NVz

30

Car (with overlay)

/ ?

MWz

31

File server

\ ?

NWz

31

Information kiosk

/ @

MXz

32

Hurricane future prediction

\ @

NXz

32

Hurricane / Tropical Storm

/ A

PAz

33

Aid station

\ A

AAz

33

Numbered box

/ B

PBz

34

BBS

\ B

ABz

34

Blowing snow

/ C

PCz

35

Canoe

\ C

ACz

35

Coastguard

/ D

PDz

36

Not used

\ D

ADz

36

Drizzle

/ E

PEz

37

Eyeball (eyecatcher)

\ E

AEz

37

Smoke

/ F

PFz

38

Farm vehicle

\ F

AFz

38

Freezing Rain

/ G

PGz

39

Grid Square (6 character)

\ G

AGz

39

Snow shower

/ H

PHz

40

Hotel (blue bed icon)

\ H

AHz

40

Haze (overlays are Hazards) Rain Shower

/ I

PIz

41

TCP/IP

\ I

AIz

41

/ J

PJz

42

Not used

\ J

AJz

42

Lightning

/ K

PKz

43

School

\ K

AKz

43

Kenwood

/ / L

GPSxyz PLz

GPSCnn 44

Icon Logged on user via APRSIS MacAPRS

\ \ L

GPSxyz ALz

GPSEnn 44 Lighthouse

Icon

/ M

PMz

45

\ M

AMz

45

Not used

/ N

PNz

46

NTS station

\ N

ANz

46

Navigation Buoy

/ O

POz

47

Balloon

\ 0

AOz

47

Rocket

/ P

PPz

48

Police

\ P

AOz

48

Parking

/ Q

PQz

49

Earthquake

\ Q

AQz

49

Earthquake

/ R

PRz

50

Recreational Vehicle

\ R

ARz

50

Restaurant

/ S

PSz

51

Space shuttle

\ S

ASz

51

Satellite / PACSAT

/ T

PTz

52

SSTV

\ T

ATz

52

Thunderstorm

/ U

PUz

53

Bus

\ U

AUz

53

Sunny

/ V

PVz

54

Amateur TV

\ V

AVz

54

VORTAC Nav aid

/ W

PWz

55

National Weather Service site Helicopter

\ W

AWz

55

NWS site (with overlay)

/ X

PXz

56

\ X

AXz

56

Pharmacy

/ Y

PYz

57

Yacht

\ Y

AYz

57

Overlays for radios and other APRS devices Not used

/ Z

PZz

58

WinAPRS

\ Z

AZz

58

/ [

HSz

59

Human

\ [

DSz

59

Wall cloud (overlays are humans) Not used

/ \

HTz

60

Triangle (DF)

\ \

DTz

60

/ ]

HUz

61

PBBS

\ ]

DUz

61

Not used

/ ^

HVz

62

Large aircraft

\ ^

DVz

62

Aircraft

/ _

HWz

63

Weather station (blue)

\ _

DWz

63

WX station with digi (with overlay) Rain

/ '

Hxz

64

Dish antenna

\ '

DXz

64

/ a

LAz

65

Ambulance

\ a

SAz

65

A=ARRL, R=RACES

/ b

LBz

66

Bicycle

\ b

SBz

66

Blowing dust or sand

/ / c

GPSxyz LCz

GPSCnn 67

Icon Incident Command Post

\ \ c

GPSxyz SCz

GPSEnn 67

Icon Civil defence (RACES)

/ d

LDz

68

Fire station

\ d

SDz

68

DX spot (from callsign prefix) Sleet

/ e

LEz

69

Horse (equestrian)

\ e

SEz

69

/ f

LFz

70

Fire appliance or truck

\ f

SFz

70

Funnel cloud

/ g

LGz

71

Glider

\ g

SGz

71

Gale flags

/ h

LHz

72

Hospital

\ h

SHz

72

Amateur radio store

/ i

LIz

73

IOTA (Island on the Air)

\ i

SIz

73

Indoor short range digi (with overlay) Work Zone (mobile digger)

/ j

LJz

74

4x4 (Land Rover or Jeep)

\ j

SJz

74

/ k

LKz

75

Truck

\ k

SKz

75

Special vehicles (with overlays) Not used

/ l

LLz

76

Laptop

\ l

SLz

76

/ m

LMz

77

MIC repeater

\ m

SMz

77

Value signpost (3 character display) Triangle (with overlay)

/ n

LNz

78

Node

\ n

SNz

78

/ o

LOz

79

Emergency operations centre Rover (dog or puppy)

\ o

SOz

79

Small circle

/ p

LPz

80

\ p

SPz

80

Partly cloudy

/ q

LQz

81

Grid square shown above 128m Antenna

\ q

SQz

81

Not used

/ r

LRz

82

\ r

SRz

82

Rest rooms

/ s

LSz

83

Ship (or power boat)

\ s

SSz

83

Ship / Boat top view (with overlay) Tornado

/ t

LTz

84

Truck stop

\ t

STz

84

/ u

LUx

85

Large truck

\ u

SUz

85

Truck (with overlay)

/ v

LVz

86

Van

\ v

SVz

86

Van (with overlay)

/ w

LWz

87

Water station

\ w

SWz

87

Flooding

/ x

LXz

88

Xastir (Unix / Linux)

\ x

SXz

88

Not used

/ y

LYz

89

Yagi antenna at location

\ y

SYz

89

Skywarn

/ / z

GPSxyz LZz

GPSCnn 90 Shelter

Icon

\ \ z

GPSxyz SZz

GPSEnn 90

Icon Shelter (with overlay)

/ (

J1z

91

Not used

\ (

Q1z

91

Fog

/ |

J2z

92

Reserved (TNC stream switch) Not used

\ |

Q2z

92

Reserved (TNC stream switch) Not used

/ }

J3z

93

\ }

Q3z

93

/ ~

J4z

94

Reserved (TNC stream switch)

\ ~

Q4z

94

Reserved (TNC stream switch)

Appendix 4
Bob Ball WB8WGA

Acknowledgements
For allowing me to base the development of the APRS TNC Digi Tracker on a TNC design he originally described in QEX. For allowing me to use parts of his assembler code for a modemless receiver design. For inventing APRS in the first place, offering help and advice on APRS and licensing APRS to Cross Country Wireless Ltd so that the APRS TNC Digi Tracker can be sold as a commercial and amateur radio product. All members especially Ross Wilkinson G6GVI and Jack McEwan G8HIK for advice and feedback. For suggestions, feedback and comment

Mike Berg N0QBH

Bob Bruninga WB4APR

Bolton RAYNET Group

Many other radio amateurs in the UK, South Africa and New Zealand

And last but not least my wife Sadie and son Robert who have supported and inspired me throughout the project. 73, Chris Moulding, G4HYG