Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Features

e·MMC™ Memory
MTFC4GMDEA-4M IT, MTFC8GLDEA-4M IT, MTFC16GJDEC-4M IT,
MTFC32GJDED-4M IT, MTFC64GJDDN-4M IT

Features Figure 1: Micron e·MMC Device

• MultiMediaCard (MMC) controller and NAND Flash

• 153- or 169-ball WFBGA/VFBGA/LFBGA (RoHS 6/6-
compliant)
• VCC: 2.7–3.6V
• VCCQ (dual voltage): 1.65–1.95V; 2.7–3.6V
• Industrial temperature ranges MMC MMC controller MMC
power interface
– Operating temperature: –40˚C to +85˚C
– Storage temperature: –40˚C to +85˚C
• Typical current consumption
– Standby current: 120µA for 4GB–16GB; 140µA for
32GB; 160µA for 64GB
– Active current (RMS): 80mA (4GB–64GB) NAND Flash
power NAND Flash

MMC-Specific Features
• JEDEC/MMC standard version 4.41-compliant
(JEDEC Standard No. 84-A441) – SPI mode not
supported (see www.jedec.org/sites/default/files/
docs/JESD84-A441.pdf)
– Advanced 11-signal interface MMC-Specific Features (Continued)
– x1, x4, and x8 I/Os, selectable by host – Enhanced reliable write
– MMC mode operation – Configurable reliability settings
– Command classes: class 0 (basic); class 2 (block – Background operation
read); class 4 (block write); class 5 (erase); – Fully enhanced configurable
class 6 (write protection); class 7 (lock card) – Backward-compatible with previous MMC
– MMCplus™ and MMCmobile™ protocols modes
– Temporary write protection • ECC and block management implemented
– 52 MHz clock speed (MAX)
– Boot operation (high-speed boot)
– Sleep mode
– Replay-protected memory block (RPMB)
– Secure erase and trim
– Hardware reset signal
– Multiple partitions with enhanced attribute
– Permanent and power-on write protection
– Double data rate (DDR) function
– High-priority interrupt (HPI)

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Features

e·MMC Performance

Table 1: MLC Partition Performance

Part Number
MTFC16GJDEC-4M IT
MTFC4GMDEA-4M IT MTFC32GJDED-4M IT
Condition MTFC8GLDEA-4M IT MTFC64GJDDN-4M IT Units
Sequential write 13.5 20 MB/s
Sequential read 44 44 MB/s
Random write 90 90 IOPs
Random read 1080 1100 IOPs

Note: 1. Bus in x8 I/O mode. Sequential access of 1MB chunk; random access of 4KB chunk. Additional performance
data, such as power consumption or timing for different device modes, will be provided in a separate docu-
ment upon customer request.
Ordering Information

Table 2: Ordering Information

Base Part Number Density Package NAND Flash Type Shipping Media
MTFC4GMDEA-4M IT 4GB 153-ball WFBGA 2 x 16Gb, MLC, 25nm Tray
11.5mm x 13.0mm x 0.8mm Tape and reel
MTFC8GLDEA-4M IT 8GB 153-ball WFBGA 2 x 32Gb, MLC, 25nm Tray
11.5mm x 13.0mm x 0.8mm Tape and reel
MTFC16GJDEC-4M IT 16GB 169-ball WFBGA 2 x 64Gb, MLC, 25nm Tray
14.0mm x 18.0mm x 0.8mm Tape and reel
MTFC32GJDED-4M IT 32GB 169-ball VFBGA 4 x 64Gb, MLC, 25nm Tray
14.0mm x 18.0mm x 1.0mm Tape and reel
MTFC64GJDDN-4M IT 64GB 169-ball LFBGA 8 x 64Gb, MLC, 25nm Tray
14.0mm x 18.0mm x 1.4mm Tape and reel

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Features

Part Numbering Information

Micron®e·MMC memory devices are available in different configurations and densities. Verify valid part numbers
by using Micron’s part catalog search at www.micron.com. To compare features and specifications by device type,
visit www.micron.com/products. Contact the factory for devices not found.

Figure 2: Marketing Part Number Chart

MT FC xx x x xx - xx xx x ES

Micron Technology Design Revision

FC = NAND Flash + Controller Production Status
NAND Flash Density Wafer Process Applied
NAND Flash Component Operating Temperature Range
Controller ID Special Options
Package Codes

Note: 1. Not all combinations are necessarily available. For a list of available devices or for further information on
any aspect of these products, please contact your nearest Micron sales office.

Device Marking
Due to the size of the package, the Micron-standard part number is not printed on the top of the device. Instead,
an abbreviated device mark consisting of a 5-digit alphanumeric code is used. The abbreviated device marks are
cross-referenced to the Micron part numbers at the FBGA Part Marking Decoder site: www.micron.com/decoder.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

General Description

General Description
Micron e·MMC is a communication and mass data storage device that includes a Multi-
MediaCard (MMC) interface, a NAND Flash component, and a controller on an ad-
vanced 11-signal bus, which is compliant with the MMC system specification. Its cost
per bit, small package sizes, and high reliability make it an ideal choice for industrial
applications like infrastructure and networking equipment, PC and servers, a variety of
other industrial products.
The nonvolatile e·MMC draws no power to maintain stored data, delivers high perform-
ance across a wide range of operating temperatures, and resists shock and vibration dis-
ruption.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Signal Descriptions

Signal Descriptions

Table 3: Signal Descriptions

Symbol Type Description

CLK Input Clock: Each cycle of the clock directs a transfer on the command line and on the data line(s). The
frequency can vary between the minimum and the maximum clock frequency.
RST_n Input Reset: The RST_n signal is used by the host for resetting the device, moving the device to the pre-
idle state. By default, the RST_n signal is temporarily disabled in the device. The host must set ECSD
register byte 162, bits[1:0] to 0x1 to enable this functionality before the host can use it.
CMD I/O Command: This signal is a bidirectional command channel used for command and response trans-
fers. The CMD signal has two bus modes: open-drain mode and push-pull mode (see Operating
Modes). Commands are sent from the MMC host to the device, and responses are sent from the
device to the host.
DAT[7:0] I/O Data I/O: These are bidirectional data signals. The DAT signals operate in push-pull mode. By de-
fault, after power-on or assertion of the RST_n signal, only DAT0 is used for data transfer. The
MMC controller can configure a wider data bus for data transfer either using DAT[3:0] (4-bit mode)
or DAT[7:0] (8-bit mode). e·MMC includes internal pull-up resistors for data lines DAT[7:1]. Immedi-
ately after entering the 4-bit mode, the device disconnects the internal pull-up resistors on the
DAT[3:1] lines. Upon entering the 8-bit mode, the device disconnects the internal pull-ups on the
DAT[7:1] lines.
VCC Supply VCC: NAND interface (I/F) I/O and NAND Flash power supply.
VCCQ Supply VCCQ: e·MMC controller core and e·MMC I/F I/O power supply.
VSS1 Supply VSS: NAND I/F I/O and NAND Flash ground connection.
VSSQ1 Supply VSSQ: e·MMC controller core and e·MMC I/F ground connection.
VDDIM Internal voltage node: At least a 0.1μF capacitor is required to connect VDDIM to ground. A 1μF ca-
pacitor is recommended. Do not tie to supply voltage or ground.
NC – No connect: No internal connection is present.
RFU – Reserved for future use: No internal connection is present. Leave it floating externally.

Note: 1. VSS and VSSQ are connected internally.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

153-Ball Signal Assignments

153-Ball Signal Assignments

Figure 3: 153-Ball FBGA (Top View, Ball Down)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

A NC NC DAT0 DAT1 DAT2 RFU RFU NC NC NC NC NC NC NC

B NC DAT3 DAT4 DAT5 DAT6 DAT7 NC NC NC NC NC NC NC NC

C NC VDDIM NC VSSQ RFU VCCQ NC NC NC NC NC NC NC NC

D NC NC NC NC NC NC NC

E NC NC NC RFU VCC VSS RFU RFU RFU NC NC NC

F NC NC NC VCC RFU NC NC NC

G NC NC RFU VSS RFU NC NC NC

H NC NC NC RFU VSS NC NC NC

J NC NC NC RFU VCC NC NC NC

K NC NC NC RST_n RFU RFU VSS VCC RFU NC NC NC

L NC NC NC NC NC NC

M NC NC NC VCCQ CMD CLK NC NC NC NC NC NC NC NC

N NC VSSQ NC VCCQ VSSQ NC NC NC NC NC NC NC NC NC

P NC NC VCCQ VSSQ VCCQ VSSQ RFU NC NC RFU NC NC NC NC

Notes: 1. Some previous versions of the JEDEC product or mechanical specification had defined
reserved for future use (RFU) balls as no connect (NC) balls. NC balls assigned in the pre-
vious specifications could have been connected to ground on the system board. To ena-
ble new feature introduction, some of these balls are assigned as RFU in the v4.4 me-
chanical specification. Any new PCB footprint implementations should use the new ball
assignments and leave the RFU balls floating on the system board.
2. VCC, VCCQ, VSS, and VSSQ balls must all be connected.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 6 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

169-Ball Signal Assignments

169-Ball Signal Assignments

Figure 4: 169-Ball FBGA (Top View, Ball Down)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

A NC NC NC NC

B NC NC

D NC NC

H NC NC DAT0 DAT1 DAT2 RFU RFU NC NC NC NC NC NC NC

J NC DAT3 DAT4 DAT5 DAT6 DAT7 NC NC NC NC NC NC NC NC

K NC VDDIM NC VSSQ RFU VCCQ NC NC NC NC NC NC NC NC

L NC NC NC NC NC NC NC

M NC NC NC RFU VCC VSS RFU RFU RFU NC NC NC

N NC NC NC VCC RFU NC NC NC

P NC NC RFU VSS RFU NC NC NC

R NC NC NC RFU VSS NC NC NC

T NC NC NC RFU VCC NC NC NC

U NC NC NC RST_n RFU RFU VSS VCC RFU NC NC NC

V NC NC NC NC NC NC

W NC NC NC VCCQ CMD CLK NC NC NC NC NC NC NC NC

Y NC VSSQ NC VCCQ VSSQ NC NC NC NC NC NC NC NC NC

AA NC NC VCCQ VSSQ VCCQ VSSQ RFU NC NC RFU NC NC NC NC

AB

AC

AD

AE NC NC

AF

AG NC NC

AH NC NC NC NC

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

169-Ball Signal Assignments

Notes: 1. Empty balls do not denote actual solder balls; they are position indicators only.
2. Some previous versions of the JEDEC product or mechanical specification had defined
reserved for future use (RFU) balls as no connect (NC) balls. NC balls assigned in the pre-
vious specifications could have been connected to ground on the system board. To ena-
ble new feature introduction, some of these balls are assigned as RFU in the v4.4 me-
chanical specification. Any new PCB footprint implementations should use the new ball
assignments and leave the RFU balls floating on the system board.
3. VCC, VCCQ, VSS, and VSSQ balls must all be connected.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Package Dimensions

Package Dimensions

Figure 5: 153-Ball WFBGA – 11.5mm x 13.0mm x 0.8mm (Package Code: EA)

Seating plane

A 0.08 A

153X Ø0.30
Dimensions apply Ball A1 ID
to solder balls post- (covered by SR)
reflow on Ø0.30 Ball A1 ID
SMD ball pads. 14 12 10 8 6 4 2
13 11 9 7 5 3 1

A
B
C
D
E
6.5 CTR F
G
H
13 ±0.1 J
K
L
M
N
P

0.5 TYP

0.5 TYP 0.7 ±0.1

6.5 CTR 0.17 MIN

11.5 ±0.1

Note: 1. Dimensions are in millimeters.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Package Dimensions

Figure 6: 169-Ball WFBGA – 14.0mm x 18.00mm x 0.8mm (Package Code: EC)

Seating plane

A 0.08 A

169X Ø0.3
Dimensions apply to
solder balls post-reflow Ball A1 ID Ball A1 ID
on Ø0.30 SMD OSP ball 14 12 10 8 6 4 2
pads. 13 11 9 7 5 3 1

A
B
C
D
E
F
G
H
J
K
13.5 CTR L
M
N
P
6.5 CTR R
T
U
18 ±0.1 V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH

0.5 TYP 0.5 TYP 0.7 ±0.1

6.5 CTR 0.17 MIN
14 ±0.1

Note: 1. Dimensions are in millimeters.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Package Dimensions

Figure 7: 169-Ball VFBGA – 14.0mm x 18.00mm x 1.0mm (Package Code: ED)

Seating plane

A 0.08 A

169X Ø0.3
Dimensions apply to
solder balls post-reflow Ball A1 ID Ball A1 ID
on Ø0.30 SMD ball pads. 14 12 10 8 6 4 2
13 11 9 7 5 3 1

A
B
C
D
E
F
G
H
J
K
13.5 CTR L
M
N
P
6.5 CTR R
T
U
V
18 ±0.1 W
Y
AA
AB
AC
AD
AE
AF
AG
AH

0.5 TYP 0.5 TYP 0.9 ±0.1

6.5 CTR 0.17 MIN
14 ±0.1

Note: 1. Dimensions are in millimeters.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Package Dimensions

Figure 8: 169-Ball LFBGA – 14.0mm x 18.00mm x 1.4mm (Package Code: DN)

Seating plane

A 0.08 A

169X Ø0.3
Ball A1 ID
Dimensions apply
(covered by SR)
to solder balls post- Ball A1 ID
reflow on Ø0.30 SMD
ball pads. 14 12 10 8 6 4 2
13 11 9 7 5 3 1

A
B
C
D
E
F
G
H
J
K
13.5 CTR L
M
N
P
6.5 CTR R
T
U
V
18 ±0.1 W
Y
AA
AB
AC
AD
AE
AF
AG
AH

0.5 TYP 0.5 TYP 1.3 ±0.1

6.5 CTR 0.16 MIN
14 ±0.1

Note: 1. Dimensions are in millimeters.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Architecture

Architecture
Figure 9: e·MMC Functional Block Diagram

e·MMC

MMC VCC
controller VCCQ
RST_n
CMD Registers
DAT[7:0]
CLK
OCR CSD RCA
VDDIM
VSS1
CID ECSD DSR
VSSQ1

NAND Flash

Note: 1. VSS and VSSQ are internally connected.

MMC Protocol Independent of NAND Flash Technology

The MMC specification defines the communication protocol between a host and a de-
vice. The protocol is independent of the NAND Flash features included in the device.
The device has an intelligent on-board controller that manages the MMC communica-
tion protocol.
The controller also handles block management functions such as logical block alloca-
tion and wear leveling. These management functions require complex algorithms and
depend entirely on NAND Flash technology (generation or memory cell type).
The device handles these management functions internally, making them invisible to
the host processor.

Defect and Error Management

Micron e·MMC incorporates advanced technology for defect and error management. If
a defective block is identified, the device completely replaces the defective block with
one of the spare blocks. This process is invisible to the host and does not affect data
space allocated for the user.
The device also includes a built-in error correction code (ECC) algorithm to ensure that
data integrity is maintained.
To make the best use of these advanced technologies and ensure proper data loading
and storage over the life of the device, the host must exercise the following precautions:
• Check the status after WRITE, READ, and ERASE operations.
• Avoid power-down during WRITE and ERASE operations.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

CID Register

CID Register
The card identification (CID) register is 128 bits wide. It contains the device identifica-
tion information used during the card identification phase as required by e·MMC proto-
col. Each device is created with a unique identification number.

Table 4: CID Register Field Parameters

Name Field Width CID Bits CID Value

Manufacturer ID MID 8 [127:120] FEh
Reserved – 6 [119:114] –
Card/BGA CBX 2 [113:112] 01h
OEM/application ID OID 8 [111:104] –
Product name PNM 48 [103:56] MMC04G
MMC08G
MMC16G
MMC32G
MMC64G
Product revision PRV 8 [55:48] –
Product serial number PSN 32 [47:16] –
Manufacturing date MDT 8 [15:8] –
CRC7 checksum CRC 7 [7:1] –
Not used; always 1 – 1 0 –

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

CSD Register

CSD Register
The card-specific data (CSD) register provides information about accessing the device
contents. The CSD register defines the data format, error correction type, maximum da-
ta access time, and data transfer speed, as well as whether the DS register can be used.
The programmable part of the register (entries marked with W or E in the following ta-
ble) can be changed by the PROGRAM_CSD (CMD27) command.

Table 5: CSD Register Field Parameters

Cell CSD CSD

Name Field Width Type1 Bits Value
CSD structure CSD_STRUCTURE 2 R [127:126] 03h
System specification version SPEC_VERS 4 R [125:122] 4h
Reserved2 – 2 TBD [121:120] –
Data read access time 1 TAAC 8 R [119:112] 4Fh
Data read access time 2 in CLK cy- NSAC 8 R [111:104] 01h
cles (NSAC × 100)
Maximum bus clock frequency TRAN_SPEED 8 R [103:96] 32h
Card command classes CCC 12 R [95:84] 0F5h
Maximum read data block length READ_BL_LEN 4 R [83:80] 9h
Partial blocks for reads supported READ_BL_PARTIAL 1 R 79 0h
Write block misalignment WRITE_BLK_MISALIGN 1 R 78 0h
Read block misalignment READ_BLK_MISALIGN 77 R 77 0h
DS register implemented DSR_IMP 1 R 76 1h
Reserved – 2 R [75:74] –
Device size C_SIZE 12 R [73:62] FFFh
Maximum read current at VDD,min VDD_R_CURR_MIN 3 R [61:59] 7h
Maximum read current at VDD,max VDD_R_CURR_MAX 3 R [58:56] 7h
Maximum write current at VDD,min VDD_W_CURR_MIN 3 R [55:53] 7h
Maximum write current at VDD,max VDD_W_CURR_MAX 3 R [52:50] 7h
Device size multiplier C_SIZE_MULT 3 R [49:47] 7h
Erase group size ERASE_GRP_SIZE 5 R [46:42] 1Fh
Erase group size multiplier ERASE_GRP_MULT 5 R [41:37] 1Fh
Write protect group size WP_GRP_SIZE 4GB, 5 R [36:32] 07h
8GB
16GB, 1Fh
32G,
64G
Write protect group enable WP_GRP_ENABLE 1 R 31 1h
Manufacturer default ECC DEFAULT_ECC 2 R [30:29] 0h
rite-speed factor R2W_FACTOR 3 R [28:26] 2h
Maximum write data block length WRITE_BL_LEN 4 R [25:22] 9h
Partial blocks for writes supported WRITE_BL_PARTIAL 1 R 21 0h

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

CSD Register

Table 5: CSD Register Field Parameters (Continued)

Cell CSD CSD

Name Field Width Type1 Bits Value
Reserved – 4 R [20:17] –
Content protection application CONTENT_PROT_APP 1 R 16 0h
File-format group FILE_FORMAT_GRP 1 R/W 15 0h
Copy flag (OTP) COPY 1 R/W 14 0h
Permanent write protection PERM_WRITE_PROTECT 1 R/W 13 0h
Temporary write protection TMP_WRITE_PROTECT 1 R/W/E 12 0h
File format FILE_FORMAT 2 R/W [11:10] 0h
ECC ECC 2 R/W/E [9:8] 0h
CRC CRC 7 R/W/E [7:1] –
Not used; always 1 – 1 – 0 1h

Notes: 1. R = Read-only
R/W = One-time programmable and readable
R/W/E = Multiple writable with value kept after a power cycle, assertion of the RST_n
signal, and any CMD0 reset, and readable
TBD = To be determined
2. Reserved bits should be read as 0.
3. The IPEAK, max driving capability can be modified according to the actual capacitive load
on the e·MMC interface signals in the user application board, using CMD4.

CMD4 Argument Driving Capability (mA)

0x01000000 4
0x02000000 8
0x04000000 12 (default)
0x08000000 16
0x10000000 20
0x20000000 24
0x40000000 28
0x80000000 32

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

ECSD Register

ECSD Register
The 512-byte extended card-specific data (ECSD) register defines device properties and
selected modes. The most significant 320 bytes are the properties segment. This seg-
ment defines device capabilities and cannot be modified by the host. The lower 192
bytes are the modes segment. The modes segment defines the configuration in which
the device is working. The host can change the properties of modes segments using the
SWITCH command.

Table 6: ECSD Register Field Parameters

Size Cell ECSD ECSD

Name Field (Bytes) Type1 Bytes Value
Properties Segment
Reserved2 – 7 – [511:505] –
Supported command sets S_CMD_SET 1 R 504 1h
HPI features HPI_FEATURES 1 R 503 3h
Background operations support BKOPS_SUPPORT 1 R 502 1h
Reserved – 255 – [501:247] –
Background operations status BKOPS_STATUS 1 R 246 0h
Number of correctly program- CORRECTLY_PRG_ 4 R [245:242] –
med sectors SECTORS_NUM
First initialization time after par- INI_TIMEOUT_PA 4GB 1 R 241 78h
titioning 8GB F4h
(first CMD1 to device ready)
16GB F6h
32GB, FFh
64GB
Reserved – 1 – 240 –
Power class for 52 MHz, DDR at PWR_CL_DDR_52_360 1 R 239 0h
3.6V3
Power class for 52 MHz, DDR at PWR_CL_DDR_52_195 1 R 238 0h
1.95V3
Reserved – 2 – [237:236] –
Minimum write performance for MIN_PERF_DDR_W_8_52 1 R 235 0h
8-bit at 52 MHz in DDR mode
Minimum read performance for MIN_PERF_DDR_R_8_52 1 R 234 0h
8-bit at 52 MHz in DDR mode
Reserved – 1 – 233 –
TRIM multiplier TRIM_MULT 4GB, 1 R 232 06h
8GB
16GB, 0Fh
32GB,
64GB
Secure feature support SEC_FEATURE_SUPPORT 1 R 231 15h

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

ECSD Register

Table 6: ECSD Register Field Parameters (Continued)

Size Cell ECSD ECSD

Name Field (Bytes) Type1 Bytes Value
SECURE ERASE multiplier SEC_ERASE_MULT 4GB, 1 R 230 02h
8GB
16GB, 06h
32GB,
64GB
SECURE TRIM multiplier SEC_TRIM_MULT 4GB, 1 R 229 03h
8GB
16GB, 09h
32GB,
64GB
Boot information BOOT_INFO 1 R 228 7h
Reserved – 1 – 227 –
Boot partition size BOOT_SIZE_MULT 1 R 226 80h
Access size ACC_SIZE 4GB, 1 R 225 06h
8GB
16GB, 07h
32GB,
64GB
High-capacity erase unit size HC_ERASE_GRP_SIZE 4GB, 1 R 224 08h
8GB
16GB, 10h
32GB,
64GB
High-capacity erase timeout ERASE_TIMEOUT_MULT 1 R 223 01h
Reliable write-sector count REL_WR_SEC_C 1 R 222 01h
High-capacity write protect HC_WP_GRP_SIZE 4GB 1 R 221 01h
group size 8GB, 02h
16GB
32GB 04h
64GB 08h
Sleep current (VCC) S_C_VCC 1 R 220 08h
Sleep current (VCCQ) S_C_VCCQ 1 R 219 08h
Reserved – 1 – 218 –
Sleep/awake timeout S_A_TIMEOUT 1 R 217 10h
Reserved – 1 – 216 –
Sector count SEC_COUNT 4GB 4 R [215:212] 0070C000h
8GB 00E88000h
16GB 01D30000h
32GB 03B20000h
64GB 07700000h

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

ECSD Register

Table 6: ECSD Register Field Parameters (Continued)

Size Cell ECSD ECSD

Name Field (Bytes) Type1 Bytes Value
Reserved – 1 – 211 –
Minimum write performance for MIN_PERF_W_8_52 1 R 210 08h
8-bit at 52 MHz
Minimum read performance for MIN_PERF_R_8_52 1 R 209 08h
8-bit at 52 MHz
Minimum write performance for MIN_PERF_W_8_26_4_52 1 R 208 08h
8-bit at 26 MHz and 4-bit at 52
MHz
Minimum read performance for MIN_PERF_R_8_26_4_52 1 R 207 08h
8-bit at 26 MHz and 4-bit at 52
MHz
Minimum write performance for MIN_PERF_W_4_26 1 R 206 08h
4-bit at 26 MHz
Minimum read performance for MIN_PERF_R_4_26 1 R 205 08h
4-bit at 26 MHz
Reserved – 1 – 204 –
Power class for 26 MHz at 3.6V3 PWR_CL_26_360 1 R 203 00h
Power class for 52 MHz at 3.6V3 PWR_CL_52_360 1 R 202 00h
Power class for 26 MHz at 1.95V3 PWR_CL_26_195 1 R 201 00h
Power class for 52 MHz at 1.95V3 PWR_CL_52_195 1 R 200 00h
Partition switching timing PARTITION_SWITCH_TIME 1 R 199 1h
Out-of-interrupt busy timing OUT_OF_INTERRUPT_TIME 1 R 198 02h
Reserved – 1 – 197 –
Card type CARD_TYPE 1 R 196 07h
Reserved – 1 – 195 –
CSD structure version CSD_STRUCTURE 1 R 194 2h
Reserved – 1 – 193 –
Extended CSD revision EXT_CSD_REV 1 R 192 5h
Modes Segment
Command set CMD_SET 1 R/W/E_ 191 0h
P
Reserved – 1 – 190 –
Command set revision CMD_SET_REV 1 R 189 0h
Reserved – 1 – 188 –
Power class POWER_CLASS 1 R/W/E_ 187 0h
P
Reserved – 1 – 186 –
High-speed interface timing HS_TIMING 1 R/W/E_ 185 0h
P
Reserved – 1 – 184 –

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

ECSD Register

Table 6: ECSD Register Field Parameters (Continued)

Size Cell ECSD ECSD

Name Field (Bytes) Type1 Bytes Value
Bus width mode BUS_WIDTH 1 W/E_P 183 0h
Reserved – 1 – 182 –
Erased memory content ERASED_MEM_CONT 1 R 181 0h
Reserved – 1 – 180 –
Partition configuration PARTITION_CONFIG 1 R/W/E, 179 0h
R/W/E_
P
Boot configuration protection BOOT_CONFIG_PROT 1 R/W, 178 0h
R/W/C_
P
Boot bus width BOOT_BUS_WIDTH 1 R/W/E 177 0h
Reserved – 1 – 176 –
High-density erase group defini- ERASE_GROUP_DEF 1 R/W/E_ 175 00h
tion P
Reserved – 1 – 174 –
Boot area write protection regis- BOOT_WP 1 R/W, 173 0h
ter R/W/C_
P
Reserved – 1 – 172 –
User write protection register USER_WP 1 R/W, 171 0h
R/W/
C_P,
R/W/E_
P
Reserved – 1 – 170 –
Firmware configuration FW_CONFIG 1 R/W 169 0h
RPMB size RPMB_SIZE_MULT 1 R 168 1h
Write reliability setting register3 WR_REL_SET 1 R/W 167 00h4
Write reliability parameter regis- WR_REL_PARAM 1 R 166 05h
ter
Reserved – 1 – 165 –
Manually start background oper- BKOPS_START 1 W/E_P 164 –
ations
Enable background operations BKOPS_EN 1 R/W 163 0h
handshake
Hardware reset function RST_n_FUNCTION 1 R/W 162 0h
HPI management HPI_MGMT 1 R/W/E_ 161 0h
P
Partitioning support PARTITIONING_SUPPORT 1 R 160 3h

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

ECSD Register

Table 6: ECSD Register Field Parameters (Continued)

Size Cell ECSD ECSD

Name Field (Bytes) Type1 Bytes Value
Maximum enhanced area size MAX_ENH_SIZE_MULT 4GB 3 R [159:157] 0001C3h
8GB 0001D1h
16GB 0001D3h
32GB 0001D9h
64GB 0001DCh
Partitions attribute PARTITIONS_ATTRIBUTE 1 R/W 156 0h
Partitioning setting PARTITION_SETTING_COMPLETED 1 R/W 155 0h
General-purpose partition size GP_SIZE_MULT 12 R/W [154:143] 0h
Enhanced user data area size ENH_SIZE_MULT 3 R/W [142:140] 0h
Enhanced user data start address ENH_START_ADDR 4 R/W [139:136] 0h
Reserved – 1 – 135 –
Bad block management mode SEC_BAD_BLK_MGMNT 1 R/W 134 0h
Reserved – 134 – [133:0] –

Notes: 1. R = Read-only
R/W = One-time programmable and readable
R/W/E = Multiple writable with the value kept after a power cycle, assertion of the
RST_n signal, and any CMD0 reset, and readable
R/W/C_P = Writable after the value is cleared by a power cycle and assertion of the
RST_n signal (the value not cleared by CMD0 reset) and readable
R/W/E_P = Multiple writable with the value reset after a power cycle, assertion of the
RST_n signal, and any CMD0 reset, and readable
W/E_P = Multiple writable with the value reset after power cycle, assertion of the RST_n
signal, and any CMD0 reset, and not readable
TBD = To be determined
2. Reserved bits should be read as 0.
3. Micron has tested power failure under best application knowledge conditions with posi-
tive results. Customers may request a dedicated test for their specific application condi-
tion.
4. Set at 00h when shipped for optimized write performance; can be set to 1Fh to enable
protection on previously written data if power failure occurs during a WRITE operation.
This byte is one-time programmable.
5. The first showing of 4GB refers to the 1-channel device, while the second showing of
4GB refers to the 2-channel device.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

DC Electrical Specifications – Device Power

DC Electrical Specifications – Device Power

The device current consumption for various device configurations is defined in the
power class fields of the ECSD register.
VCC is used for the NAND Flash device and its interface voltage; V CCQ is used for the
controller and the e·MMC interface voltage.

Figure 10: Device Power Diagram

VCC
C3 C4

VCCQ
C1 C2

Core regulator
NAND NAND Flash
VDDIM control signals
C5 C6
I/O block

I/O block
NAND
MMC

CLK
Core NAND
CMD
logic block
data bus

VCCQ
DAT[7:0]

MMC controller
VCCQ

Table 7: Power Domains

Parameter Symbol Comments

Host interface VCCQ High voltage range = 3.3V (nominal)
Low voltage range = 1.8V (nominal)
Memory VCC High voltage range = 3.3V (nominal)
Internal VDDIM The internal regulator connection to an external decoupling capacitor

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

DC Electrical Specifications – Device Power

Table 8: Capacitor and Resistance Specifications

Parameter Symbol Min Max Typ Units Notes

Pull-up resistance: CMD R_CMD 4.7 50 10 kΩ 1
Pull-up resistance: DAT[7:0] R_DAT 10 50 50 kΩ 1
Pull-up resistance: RST_n R_RST_n 4.7 50 50 kΩ 2
CLK/CMD/DAT[7:0] impedance 45 55 50 Ω 3
Serial resistance on CLK SR_CLK 0 47 22 Ω
VCCQ capacitor C1 2.2 4.7 2.2 µF 4
C2 0.1 0.22 0.1
VCC capacitor (≤8GB) C3 2.2 4.7 2.2 µF 5
C4 0.1 0.22 0.1
VCC capacitor (>8GB) C3 2.2 4.7 4.7 µF 5
C4 0.1 0.22 0.22
VDDIM capacitor (Creg) C5 1 4.7 1 µF 6
C6 0.1 0.1 0.1

Notes: 1. Used to prevent bus floating.

2. If host does not use H/W RESET (RST_n), pull-up resistance is not needed on RST_n line
(Extended_CSD[162] = 00h).
3. Impedance match.
4. The coupling capacitor should be connected with VCCQ and VSSQ as closely as possible.
5. The coupling capacitor should be connected with VCC and VSS as closely as possible.
6. The coupling capacitor should be connected with VDDIM and VSS as closely as possible.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
 Micron Confidential and Proprietary

4GB, 8GB, 16GB, 32GB, 64GB: e·MMC

Revision History

Revision History
Rev. B – 09/13
• To Production status
• Added channel note to ECSD Register

Rev. A – 03/13
• Initial release

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900

www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization some-
times occur.

PDF: 09005aef8523ca91
emmc_4gb-64gb_ctrd_441-it.pdf - Rev. B 09/13 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.