SIMOVERT MASTERDRIVES CUVC Short Guide to the Basic Functions

(Please pay attention to the Operating Instruction (BA) chapter and diagram references)

General: Connections 1 Connections 2

BA = Operating instruction (BA Power Connections): (BA Control Connections): Control commands:
WR = Inverter
PW = Pulse resistor or Default for
regenerative feedback Line 24V H X101.1 P368 = 1 P368=0,7
BEx = Binary input Terminal strip PMU, OP1S
0V L .2
BAx = Binary output 20mA
AEx = Analog input BA1 (BE1) .3 P651 =B107 No fault =B107
AAx = Analog output 20mA .4 P652 =B104 Operation =B104
PMU BA2 (BE2)
Bxxx = Number of a binary signal
(binector) B0=0, B1=1 20mA BA3 (BE3) .5 P653 =B115 No alarm BE3 P590=14
X101
Kxxx = Number of an analog signal (BA4) BE4 .6 B016 INV enable P561=16 P561=1
(connector) K0=0%, K1=100% X102
Pxxx = Number of a parameter BE5 .7 B018 ACK P567=18 P567=0
(Index = 1, if present and X103 BE6 .8 B020 OFF2 P555=20 P555=1
not otherwise designated)
BE7 .9 B022 ON/OFF1 P554=22 P554=5, 2100
Ref. values for analog signals:
2 wire  RS 485 P .10 1 3 Switch S2 IMPORTANT:
Motor
10 V = 100 % Ref Value If present: USS (SST2)  Dual connecting
P350 = Ref Amps set fan  RS 485 N .11
P352 = Ref Frequency of terminals
transformer to RS 485 ref .12 2 4
P353 = Ref Speed Bus termination X101.3 ... .6 as
line voltage
P353 = P352 * 60 / No. of pole pairs BAx and BEx
(BA Fan fuse)
Ref values can be changed only in not allowed!
+10 V 5 mA X102.13
P60=5 Drive Setting Setpoints / analog outputs are shown below
-10 V 5 mA .14
Parameterizing
±10 V AE1 .15 K11 3 Switch S3
1 P632.1, .2
(BA Parameterizing):
open: ± 10 V 0
•009
v/f characteristics:
Operator display 0V AE1 .16
(P100=0, 1, 2) 0 ... 10 V 1
005 : Drive setting
Diagram r0, r1, r2 ±10 V AE2 .17 K13 closed: ± 20 mA 2
008 : Switch-on inhibit 4 2
Operation via BA Quick 0 ... 20 mA 3
↓ P
↑ 009 : Ready for switching on
014 : Operation PMU: parameterizing 0V AE2 .18 AE2 AE1 4 ... 20 mA 4
I/O
P554 = B005 ±10 V, 5 mA AA1 .19 P640.1 3 6 Switch S4
Speed left : ± 10 V
r000
P
Monitoring Acknowledge fault 0V AA1 .20
P101

parameters P330=0 right : ± 20 mA

P571 = B006 M = const. ±10 V, 5 mA AA2 .21 P640.2 20 ... 0 mA
I
P572 = B007 Current 1 2 4 5 20 ... 4 mA
0V AA2 .22 AA1 AA2
P060
O P
Variable P573 = B008 Current outputs with
P325

parameters X300
P574 = B009 reversed sign
P 0V X103.23 Calculation: Diagram a0
Index (not Operation via Track A .24
f Note:
all parameters) OP1S: P326 P293 Track B .25 The screen of the tacho lead
T
P I/O P554 = B2100 must be earthed to the motor
Zero pulse .26
and converter housings over a
P101

P565 = B2107
1
R
Change Fault P330 = 1
Run
M ~ n2 Control input .27 wide area.
parameter Jog P568 = B2108
value
I
+ 15 V 190mA .28
0 P P571 = B2111 In P60=5 (Drive setting):
.29 P130=11=Pulse encoder
P325

7 8 9 P572 = B2112 Motor

5 4
1
5
2
6
3
P573 = B2113 temperature .30 P151=Increment (1024)
0 +/- P574 = B2114 PTC KTY84 sensor
P Save new f
value P380 = 1°C P380 = Alarm temp. in °C
For binectors: see control commands P293
P381 = 1°C P381 = Fault temp. in °C

Quick parameterization (BA Parameterizing steps) P382, P383 for i²t calculation with ROTEC induction motors (P95 = 2, P97 > 0) assigned automatically.
°021 P382: Motor Cooling (0=self-ventilated, 1=separately ventilated)
P060: Menu Select → 3 indications: P383: Motor thermal time constant (0s=n protection; value ≥ 100s: Table BA Quick parameterization)
P071: Line Volts (AC or DC, depending on unit) P370: Start quick parameterization → 1 (All reference values P350. .P354 are set to motor rated values)
P095: Type of Motor (IEC=10 NEMA=11 ROTEC=02 *) P60=0 (User menu)
P097: Motor Number --- --- 1PH7(=1PA6) 1PL6 1PH4 Type of t( 1=v/f curve; 2=v/f curve, textile; 3=Vector ctrl without encoder (f-Reg.); 4=Vector control with pulse encoder )
P100: Control Mode see right see right see right control (diagram r1) (diagram r2) (diagram r3) (diagram r4)
P101: Motor Rtd V Voltage (V) Voltage (V) ---
P102: Motor Rtd A Current (A) Current (A) --- P462 : Acceleration time on P352=reference frequency or P353=reference speed
P104: MotPwrFactor cos PHI --- --- P464 : Deceleration time on P352 or P353 on 0Hz
P105: Mot Rtd Power --- Power (hp) --- P60= 5 (Drive setting)
P106: Mot Rtd Effic. --- Efficiency % --- P330 : v/f type of characteristic -> 0=linear,
P107: Mot Rtd Freq Frequency Frequency (Hz) --- 1=parabolic (pump, fan) Fans, pumps in the case of vector control (P60=1):
P108: Mot Rtd Speed Speed Speed (1/min) --- see P291, P295, P303
P109: Motor #PolePairs is automatically calculated from P107 and P108 P452 : Maximum frequency FWD speed in % of P352 or P353 PMU displays by P
P114: Technol. Cond. (vector control only) = Standard → 0 P453 : Maximum frequency REV speed in % of P352 or P353 and I key:
with pumps/fans: = Part-load optimization → 5 P60=0 (User menu)
Motor identification at standstill (motor gets organized): P115=2* (also in the case of v/f characteristic) P A078 °009 I °018 °009

P368: Setpoint source 0 = PMU + motor potentiometer (diagram s0); Unit is ready for power up from now onwards
1 = Analog input + terminal strip (diagram s1); No-load measurement (motor rotating !): P115=4* ( not in the case of v/f characteristic) P A080 °009 I °019 °009
7 = OPS1 + Fixed setpoints (diagrams s7 and s71) Controller optimization (if no gear backlash !): P115=5* ( not in the case of v/f characteristic ) P A080 °009 I °019 °009
continued at right P471 : Precontrol, acceleration *The ON command must be given within 20s!
* List for ROTEC induction motors in BA Quick Parameterization

When P60=1 (parameter menü) more parameters are accessible than on diagrams ax, sx, rx of the BA (P60=0).
Further parameters (P60 = 0 = user menu): Further parameters (P60 = 1 = parameter menu): Further parameters (P60 = 1):
Parameters visible when P60=0 are defined in P360 Deceleration time for quick stop (OFF3) P466 in s Motor load limits i²t (i001=alarm,i002=fault) P384.x in %
Prot ramp gen. gain Kp (P100<=3, f<15%) P467 Flying restart (e.g. for fans) P583 (1=ON)
Current limitation P128 in A Ramp end/ramp start smooth P469 P470 in s Fly search speed P526 in Hz/s
Slip compensation (P100=1) P336 in % Minimum frequency P457 in % * DC bus volts reg. (if no pulse resistor) P515 (1=ON)
Static/dyn. torque (P100=3) P278/P279 in % * Skip frequency P455 in % * Frequency limit for turn-off value OFF1 P800 in % *
defines the current magnitude at f<10% Fixed setpoint 5 in Hz (K045) P405 in Hz
Torque limits (P100=3,4) P492/P498 in % * Excitation/de-magnetize time P602 P603 in s * % values are referred to P352, P353 or P354/P113
Speed controller Kp, Tn (P100=0,3,4) P235 P240 in ms

Control commands: Default for... (P368=0 diagrm s0) (P368=1 s1) (P368=7 diag s7) Setpoints: Default for... (368=0 diag. s0) (368=1 diag. s1) (368=7 diag. s71)
ON/OFF1 command P554 B005 (PMU) B022 (BE7) B2100 Main setpoint P443 = K058 K011 = Analog input1 K040 = Fxd setpoint
Coast (OFF2) P555, 556, 557 B001 = 1 B020 (BE6) 1 (=Motor pot.) (K013 = AE2) (P405=FSW 5 in Hz
Quick stop (OFF3) P558, 559, 560 1 1 1 & P417=1)
INV release P561 1 B016 (BE4) 1 Additional setpoint 1: P433 (P401=FSW 1 in %
Setpoint release P564 1 1 1 & P417=0)
Fault reset P565, 566, 567 B2107 (OP1S) B018 (BE5) B2107 Analog outputs P640.x (Index 1: AA 1; Index 2: AA 2) (see diagram a0 of Operating Instruction):
Jog (n/f: P448 in %) P568 B000 = 0 0 B2108 Default setting: P640.1 = speed = K148 (Speed n: P002 in Hz (K020))
FWD speed P571 1 (B006 = PMU) 1 B2111 P640.2 = output current = K022 (Current I: P004 in A (K022))
REV speed P572 1 (B007 = PMU) 1 B2112 Gain: P643.x Output voltage Ua: P003 in V (K021)
Motor pot. raise P573 B008 (PMU) 0 0 Offset: P644.x DC link voltage Ud: P006 in V (K025)
Motor pot. lower P574 B009 (PMU) 0 0
External fault P575 1 1 1 The control command defaults in the cass of P368=0 apply when:
BE3=0=BICO data set 1=basic data set!
Note: 0 = continuous 0 = L = 0V = terminal X101.2; 1 = continuous 1 = H = 24V = terminal X101.1 BICO data set changeover (basic/reserve data set): P590 = B014 = BE3
Example: ON/OFF1 command (P554) setpoint source P368=1 from BE7 (binector B022): P554=22 BA3 can only be used when P590=0 ! BE3 can only be used when P653=0 !

Problems? - Fault : Indication Fxxx (see Operating Instruction, Faults)

- Drive does not behave as it should: Reset : Clear the cause of the fault, then P
Parameter settings lost; repeat quick parameterization (contains factory settings); Check motor rating Return to parameterizing level : Press P and at the same time
plate data and type of connection (e.g.star/delta); then reset parameters.
- Drive does not start: - Alarm : Indication Axxx (see Operating Instruction, Alarms)
Where P100=1, 2 : Use P325 to increase the voltage boost at 0 Hz. Disappears automatically when the cause has been eliminated.
Where P100=3 : Use P278,P279 to increase the current at low speeds, or increase P467 The diagrams in the Operating instruction for quick parameterization refer to the detailed
Where P100=3,4 : Use P492 to increase the torque limit. If P100=4: check tachometer wiring diagrams of all functions and parameters in the "Compendium", e.g.: Sheet 90 terminal strip