Scribd
Upload
85 views4 pages

6 DOF Sensor MPU6050 (SKU:SEN0142) : 1 2 Specification 3 Connection Diagram 4 Sample Code

Uploaded by

Ali TubeAccount
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views4 pages

6 DOF Sensor MPU6050 (SKU:SEN0142) : 1 2 Specification 3 Connection Diagram 4 Sample Code

Uploaded by

Ali TubeAccount
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

 

6 DOF Sensor‐MPU6050 (SKU:SEN0142) 

Contents

 1 Introduction
 2 Specification
 3 Connection Diagram
 4 Sample Code

Introduction
At the beginning,the inertial measurement unit is an electronic device that measures and reports on
a craft's velocity, orientation, and gravitational forces, using a combination of
accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-
computer interaction(HCI), navigational purposes and balancing technology used in the Segway
Personal Transporter as we all known.

The MPU-6000/MPU-6050 family of parts are the world’s first and only 6-axis MotionTracking
devices designed for the low power, low cost, and high performance requirements of smartphones,
tablets and wearable sensors.

The MPU-6000/6050 devices combine a 3-axis gyroscope and a 3-axis accelerometer on the same
silicon die together with an onboard Digital Motion Processor (DMP) capable of processing complex
9-axis MotionFusion algorithms. The parts’ integrated 9-axis MotionFusion algorithms access
external magnetometers or other sensors through an auxiliary master I2C bus, allowing the devices
to gather a full set of sensor data without intervention from the system processor.

The 6 Dof sensor breakout integrate with the MPU6050 sensor and the low noise 3.3v regulator and
pull-up resistors for the I2C bus. So it's available to directly hook up the sensor with the Arduino
processors for your robotics,HCI and wearable projects. With the Arduino library from i2cdevlib it's
easy for you to drive this sensor and get the pitch,roll,yaw,quaternion,euler data.

Specification
 Working voltage: 3~5v
 I2C Digital-output of 6 or 9-axis MotionFusion data in rotation matrix, quaternion, Euler Angle, or raw
data format
 Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of
±250, ±500, ±1000, and ±2000dps
 Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
 Digital Motion Processing (DMP) engine offloads complex MotionFusion, sensor timing
synchronization and gesture detection
 Embedded algorithms for run-time bias and compass calibration. No user intervention required
 Dimensions: 14 x 21mm

Connection Diagram 
 

Sample Code

Please download the libraries for the all the IMU sensors first!

/*
# Product: 6 DOF Sensor-MPU6050
# SKU : SEN0142
# Description:
# To read accel/gyro data from 6 DOF Sensor
*/

#include "Wire.h"
#include "I2Cdev.h"
#include "MPU6050.h"
MPU6050 accelgyro;
int16_t ax, ay, az; // define accel as ax,ay,az
int16_t gx, gy, gz; // define gyro as gx,gy,gz

#define LED_PIN 13
bool blinkState = false;

void setup() {
Wire.begin(); // join I2C bus
Serial.begin(38400); // initialize serial communication
Serial.println("Initializing I2C devices...");
accelgyro.initialize();

// verify connection
Serial.println("Testing device connections...");
Serial.println(accelgyro.testConnection() ? "MPU6050 connection successful"
: "MPU6050 connection failed");

pinMode(LED_PIN, OUTPUT); // configure LED pin


}

void loop() {
accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz); // read measurements f
rom device

// display tab-separated accel/gyro x/y/z values


Serial.print("a/g:\t");
Serial.print(ax);
Serial.print("\t");
Serial.print(ay);
Serial.print("\t");
Serial.print(az);
Serial.print("\t");
Serial.print(gx);
Serial.print("\t");
Serial.print(gy);
Serial.print("\t");
Serial.println(gz);

// blink LED to indicate activity


blinkState = !blinkState;
digitalWrite(LED_PIN, blinkState);

Powered By DFRobot © 2008-2017

You might also like