Scribd
Upload
46 views7 pages

Power Electronics Lab Assignment-XII: Objective

This document provides instructions for simulating a 3-phase half-wave fully controlled AC-DC converter in MATLAB Simulink. It describes the objective of simulating and analyzing the converter. It lists the required components as MATLAB Simulink and shows diagrams of the rectifier classification chart and 3-phase input. It provides steps for setting up the simulation, including required blocks from the Simulink library and their locations. Circuit diagrams show the Simulink model for the converter. Scope output waveforms are displayed for firing angles of 0, 30, and 60 degrees. Students are tasked to simulate configurations for all firing angles and plot signals, then calculate average current for a battery charging circuit.

Uploaded by

KASHIF zaman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
46 views7 pages

Power Electronics Lab Assignment-XII: Objective

This document provides instructions for simulating a 3-phase half-wave fully controlled AC-DC converter in MATLAB Simulink. It describes the objective of simulating and analyzing the converter. It lists the required components as MATLAB Simulink and shows diagrams of the rectifier classification chart and 3-phase input. It provides steps for setting up the simulation, including required blocks from the Simulink library and their locations. Circuit diagrams show the Simulink model for the converter. Scope output waveforms are displayed for firing angles of 0, 30, and 60 degrees. Students are tasked to simulate configurations for all firing angles and plot signals, then calculate average current for a battery charging circuit.

Uploaded by

KASHIF zaman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Power Electronics Lab Assignment-XII

SIMULATION OF 3-Ф HALF WAVE FULLY CONTROLLED AC-DC CONVERTER.

OBJECTIVE:

Simulation and Analysis of Three Phase Half Wave Fully Controlled AC-DC Converter.

COMPONENTS REQUIRED:

MATLAB Simulink.

Fig: 3.1: Rectifier Classification Chart.

Fig: 3.2: Three Phase Input.


Power Electronics Lab Assignment-XII

SETTING UP SIMULATION:

1) Run MATLAB software by double click on desktop icon.


2) Open blank untitled Simulink model window for creating a new model.
3) Drag and drop required blocks from Simulink library Browser window.
4) Make the circuits as shown in circuit diagrams.
5) Plot the waveforms for source and load voltage.

REQUIRED BLOCKS AND THEIR LOCATION IN SIMULINK LIBRARY:

S.NO Block Name Block set location in the


Simulink library browser
1 AC Voltage Source Simpower/Electrical Sources
2 Thyristor Simpower/Power Electronics

3 Three phase Simpower/ Electrical Sources


Programmable
Voltage Source
4 RLC Branch Simpower/Elements
5 Powergui Simpower
6 Three Phase V-I Simpower/Measurement
Measurement
7 Scope and Display Simulink/Sink
8 Pulse Generator Simulink/Sources
Table.3.1: Required Blocks and Their Location in Simulink Library.
Power Electronics Lab Assignment-XII

SIMULINK MODEL:

Fig: 3.3: 3 Ф Half Wave Rectifier Simulation.

Fig: 3.4: 3 Ф Voltage Source Setting.


Power Electronics Lab Assignment-XII

Fig: 3.5: Pulse Generator1 Setting.

Fig: 3.6: Pulse Generator2 Setting.


Power Electronics Lab Assignment-XII

Fig: 3.7: Pulse Generator3 Setting.

SCOPE OUTPUT:

Fig: 3.8: Scope Output for 3 Ф Half Wave Rectifier Simulation (α = 0).
Power Electronics Lab Assignment-XII

Fig: 3.9: Scope Output for 3 Ф Half Wave Rectifier Simulation (α = 30).

Fig: 3.10: Scope Output for 3 Ф Half Wave Rectifier Simulation (α = 60).
Power Electronics Lab Assignment-XII
Student Task:

1. Simulate the configuration for all angles (0, 30, 60, and 90) and plot source signal, output
voltage and output current for load R and RL. Set R=20Ω and L=50mH.

2. Figure below shows a battery charging circuit using SCRs. The input voltage from neutral
to any line is 230V V(rms) and firing angle for thyristor is 30 0 . Find the average current
flowing through the battery. (Iavg= 19.95A).

NOTE: Follow the “PE_LAB_REPORT_TEMPLATE” uploaded in Class Team.

You might also like