Model: A194518R0v06

DX-1710-2200-65-18i-M-R
EasyRET 2-Port High-Band Antenna with 1 Integrated RCU – 1.4 m

Antenna Specifications
Electrical Properties
1710–2200 (b)
Frequency range (MHz)
1710–1880 1850–1990 1920–2170 2170–2200

Polarization +45° , -45°

Electrical downtilt (°) 0–10 , continuously adjustable

At mid tilt 17.4 17.8 18.0 17.9

Gain (dBi)
Over all tilts 17.2±0.4 17.6±0.4 17.7±0.4 17.8±0.4
Side lobe suppression for first
> 19 > 19 > 18 > 17
side lobe above main beam (dB)
Horizontal 3 dB beam width (°) 68±1.5 67±1.5 66±2 63±2
Vertical 3 dB beam width (°) 7.4±0.4 6.9±0.4 6.5±0.4 6.0±0.3
VSWR < 1.5

Cross polar isolation (dB) ≥ 30

Front to back ratio, ±30° (dB) > 28 > 28 > 27 > 27

Cross polar ratio, 0° (dB) > 22 > 22 > 22 > 18

Max. effective power per port (W) 300 (at 50℃ ambient temperature)

Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)

Impedance (Ω) 50

Grounding DC grounding

1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).

64
2. Electrical datasheet is available in XML format.

Mechanical Properties
Antenna dimensions (H x W x D) (mm) 1365 x 155 x 89
Packing dimensions (H x W x D) (mm) 1695 x 195 x 155
Antenna weight (kg) 6.2
Antenna packing weight (kg) 10.8 (Including clamps)
Radome material Fiberglass
Radome colour Light grey
1392
1365

Operational temperature (℃) -40 to +65

Frontal: 220 (at 150 km/h)
Wind load (N) Lateral: 110 (at 150 km/h)
Maximum: 290 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 2 x 4.3-10 Female
Connector position Bottom

Accessories Unit: mm

Item Model Description Weight Units per antenna

2 clamps,
Clamp kit-A ASMC00012 2.1 kg 1
mast diameter: 38–115 mm
Downtilt kit-A ASMDT0A01 Mechanical downtilt: 0–12° 0.6 kg 1 (Separate packing)

1
 Model: A194518R0v06
DX-1710-2200-65-18i-M-R
EasyRET 2-Port High-Band Antenna with 1 Integrated RCU – 1.4 m

Antenna Information Management Module (AIMM) Specifications

Properties
RET type Integrated RET
RET protocols* AISG 2.0/3GPP
Input voltage range (V) 10–30 DC
< 0.5 (when the motor does not work, 12 V)
Power consumption (W) < 3 (when the motor is working, 12 V)
< 10 (when the motor is starting up or shutting down, 12 V)
Adjustment time (full range) (s) Typ. 30 (typically, depending on antenna type)
2 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male/Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC Not used RS-485B Not used RS-485A DC DC return Not used
2.5 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET
antenna software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more
details about protocol switching function, contact Huawei before system installation.
Standards: EN/IEC 60950-1(Safety), EN/IEC 60950-22(Safety – Equipment installed outdoor), EN 55032 (Emission),
EN/IEC 62368-1(Safety), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM, RoHS, REACH, WEEE

Port and Array Layout

1–2

b: Blue b

Port Array Freq(MHz) RET S/N

1–2 b 1710–2200 HWxxxxx……..b

Pattern Sample for Reference

1710–2200 MHz
NOTE (b)
1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to requirements
described in the antenna installation guide.
5. In the effort to improve our products, all specifications are subject to change without notice.

Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna

2 Issue: 2021–12–20