Designed especially for use as a primary relief device on large

stationary pressurized storage containers with flanged openings.

These manifolds incorporate an additional relief valve, not included
in the flow rating, allowing for servicing or replacement of any one of
the relief valves without evacuating the container. The handwheel on
the manifold selectively closes off the entrance port to the relief valve
being removed while the remaining relief valves provide protection for
the container and its contents. All manifold flow ratings are based on
flow through the relief valves after one has been removed for service
or replacement.

• Allows for relief valve removal and replacement on a periodic

basis without shutting down and evacuating the container.

• “Pop-action” design of relief valves insures maximum protection

with only minimal product loss at moderately excessive pressures.

• A rubber plug with chain is provided to protect manifold outlet

threads where the relief valve has been removed.

• May be mounted directly to a welding neck flange or manhole

cover plate. Requires no inlet piping.

• Relief valves designed to automatically reseat firmly after

discharge.

• Resilient relief valve seat disc provides “bubble-tight” seal.

• Relief valves are ASME rated for use with LP-Gas and anhydrous
ammonia.

Body .............................................................................. Ductile Iron

Resilient Parts ........................................................................ Teflon
Clapper Disc ............................................................. Stainless Steel
Bleeder Valve ........................................................... Stainless Steel

7560-55 1-Bolt Stud All RegO and 4”-ANSI 300#

Welding Neck Flange 8
and Nut Multiports®
7560-56 Manhole Cover Plate
NOTE: Studs and Nuts are not included.

Body Upper Cold Rolled Steel Lower Ductile Iron

Liner Stainless Steel
Spring Guide Stainless Steel
Spring Coated Steel
Seat Disc Resilient Synthetic Rubber
*A special coating is applied to the inlet threads to minimize possibility of electrolytic action.

100 RegO Dr. Elon, NC 27244 USA www.regoproducts.com +1 (336) 449-7707

 Safety Groove
RegO Pressure Relief Valve
Excessive stress on vent piping
“Pop-action” insures maximum
attached to relief valve will break
protection with only minimum
valve body at this point, leaving
fluid loss at moderately
valve fully operative.
excessive pressures.
Handwheel
Large, heavy duty handwheel has
raised port numbers for selective
Weep Hole Deflector positioning of clapper disc. Raised
Port design of deflector prevents “arrow” below handwheel indicates
any ignited fluid ejected from the exact position of clapper disc at all
weep hole, while the relief valve is times.
functioning, from impinging on the
storage container or adjacent piping Clapper Disc
and equipment. Shown in position to remove relief
valve. Normally, clapper disc is
positioned between any two relief
valves.
Resilient Seat Disc
Assures positive shut-off. Bleeder Valve
Shown in “closed” position to bleed
off pressure trapped between relief
Manifold Seat Ring valve and clapper disc prior to
Has integral teflon seat ring for removal of relief valve.
positive shutoff of valve port by
clapper disc. Ductile Iron Body
Rugged. Has corrosion resistant
lacquered finish.
Instruction Plate Flanged Tank Connection
For relief valve replacement. Available with either a modified
ANSI 3” (4” port opening) or a 4”
Plug Assembly ANSI 300# flanged connection.
Protects manifold outlet threads Mates respectively with modified
and keeps foreign material out ANSI 3” 300 lb. flat face steel flange
of manifold when relief valve is
removed for retest. face steel flange.

Spacious Manifold Port

Passages large unobstructed throat
ensures minimum capacity loss.
Manifold is bolted directly to storage
container opening, eliminating any
3” restrictions.
A8560 300# 4”
7564-48
(4” Port Dia) Flat Faced.
Gasket
A8570 4” ANSI 4” Johns-Manville Flexitallic flange
4”
AA8570 300#
1/16 ” Raised Faced.
7565-48 gasket furnished with each manifold
assembly.

A8563G 3 18,500 (2)

3”-300#*
A8564G 4 27,750 (3) Not
A3149MG
A8573G 3 18,500 (2) Applicable
4”-300#
A8574G 4 27,750 (3)
250 Yes Yes 2½” ****
A8563AG 3 18,300 (2)
3”-300#*
A8564AG 4 Not 27,400 (3)
A3149G
A8573AG 3 Applicable 18,300 (2)
4”-300#
A8574AG 4 27,400 (3)
* For use with modified 300# ANSI flange with 4” port.
*** 2” F. NPT outlet connection.
** Flow rating based on number of relief valves indicated in parentheses ( ).
**** Outlet 3½-8N (F) thread, will accept 3” M. NPT pipe thread.
Flow rates shown are for bare relief valves. Adapters and pipeaways will
reduce flow rates as discussed in the Foreword section.

100 RegO Dr. Elon, NC 27244 USA www.regoproducts.com +1 (336) 449-7707