Heavy Duty

Roller Chain

An introduction to Heavy Duty and Super Series Chain

e
c
t
i

Tsubaki offers Heavy Duty and SUPER Series roller chains for applications that exceed the capabilities of Tsubaki ANSI standard RS
o
n

Roller Chain. These heavy duty applications include the following:

A

1. Severe operating conditions such as heavy shock loads.

2. Where space to put the chain is limited. A Heavy Duty chain will often deliver the same tensile strength of a larger size of
Standard RS Roller Chain.
3. Operating conditions that require higher horsepower ratings, maximum allowable load and tensile strength.

H (Heavy) Series roller chain differs from ANSI (RS) standard series roller chain only in the extra thickness of the link plates. These
H (Heavy) Series:

link plates have the same thickness as the link plates of the next larger size of ANSI standard series. The thicker link plates provide
(approximately 10%) greater capacity for absorbing shock loads. Through hardened pins are used up to size 140 chain. Above size
140, the pins are case hardened. H series chains are especially suited to situations where the load is heavy and operating speeds are
low (up to 165 ft./min.), or where operating conditions are severe.

The dimensions of this series are identical to those of ANSI (RS) standard series roller chain. The special design of the SUPER series
SUPER Series:

link plates delivers exceptional performance. The pitch holes are critically formed and drifted to improve their allowable tension by
25%-30%; and the pins are through hardened for greater shock resistance. SUPER series chains offer horsepower ratings 30%
greater than the equivalent size ANSI standard chain. SUPER series chains can be used to replace the next larger size of ANSI
standard chain, making it ideal for applications where space is limited.

HT series chains provide a (15%-30%) greater ultimate tensile strength over ANSI standard roller chain by using through hardened
HT Series:

pins and link plates of the next larger ANSI standard chain sizes. The dimensions of the chain are identical to the H Series (above).
HT Series chains also provide a greater shock load resistance and are best suited for low operating speeds – up to 165 ft./min.

The thickness of SUPER-H series link plates is the same as the next larger size of SUPER series chain. The pins are also through
SUPER-H Series:

hardened which provides a 13% greater ultimate tensile strength and 6% greater allowable tension than SUPER series chain.
SUPER-H series chains can be used to replace the next largest size of ANSI standard chain, making it ideal for applications where
space is limited. It is best suited for low speed operating conditions – up to 165 ft./min.

ULTRA SUPER series offer longer wear life, greater allowable load, higher tensile strength than any other Tsubaki roller chain. This
ULTRA SUPER Series:

chain is well suited for applications where there are space limitations. The heavy duty construction of the ULTRA SUPER series
chains allows it to replace an (up to) two sizes larger ANSI standard roller chain. It is best suited for low speed operating conditions –
up to 165 ft./min.

Drive Chain A48 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

Comparison of Tensile Strength and Maximum Allowable Load

S
e
c
t
i
o

Tensile Strength Comparison

n

Comparison of tensile strength

Standard Chain and Heavy Series 100
(average tensile strength) using
ANSI Standard Roller Chain
SUPER Chain 109
as a base.
HT Series Chain 119

SUPER-H Chain 123

ULTRA SUPER Chain 144

Maximum Allowable Load Comparison

Comparison of maximum
Standard Chain 100 allowable load (average
maximum allowable load)
SUPER Chain 132
using ANSI Standard Roller
HT Series Chain and Heavy Series Chain as a base.
109

SUPER-H Chain 140

ULTRA SUPER Chain 162

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A49
 Heavy Duty
Roller Chain

Heavy Series
S
e
c

Heavy Duty Roller Chain

t
i
o
n

All dimensions in inches unless otherwise stated.

Link Plate Pin
Width
Between Average Maximum
Bushing Inner Link Transverse Tensile Allowable Approximate
Pitch Diameter Plates Thickness Height Height Diameter Length Length Length Pitch Strength Load Weight
Chain Number P R W T H h D L 1 + L2 L1 L2 C (lbs.) (lbs.) (lbs./ft.)
Single Strand
RS60H 0.750 0.469 0.500 0.126 0.713 0.614 0.235 1.165 0.583 0.669 - 9,920 2,200 1.21
RS80H 1.000 0.625 0.625 0.157 0.949 0.819 0.313 1.441 0.720 0.823 - 17,640 3,630 2.08
RS100H 1.250 0.750 0.750 0.189 1.185 1.024 0.376 1.717 0.858 0.965 - 26,460 5,510 3.07
RS120H 1.500 0.875 1.000 0.220 1.425 1.228 0.437 2.122 1.061 1.203 - 37,480 7,270 4.38
RS140H 1.750 1.000 1.000 0.252 1.661 1.433 0.500 2.276 1.138 1.303 - 48,510 9,590 5.54
RS160H 2.000 1.125 1.250 0.283 1.898 1.638 0.563 2.673 1.337 1.514 - 60,360 12,500 7.35
RS200H 2.500 1.563 1.500 0.374 2.374 2.047 0.781 3.378 1.689 1.894 - 103,630 17,600 12.33
RS240H 3.000 1.875 1.875 0.500 2.850 2.457 0.937 4.315 2.157 2.453 - 152,140 25,300 19.54
Double Strand
RS60H-2 0.750 0.469 0.500 0.126 0.713 0.614 0.235 2.189 1.094 1.177 1.028 19,840 3,700 2.41
RS80H-2 1.000 0.625 0.625 0.157 0.949 0.819 0.313 2.724 1.362 1.465 1.283 35,280 6,100 4.15
RS100H-2 1.250 0.750 0.750 0.189 1.185 1.024 0.376 3.260 1.630 1.736 1.539 52,920 9,300 6.07
RS120H-2 1.500 0.875 1.000 0.220 1.425 1.228 0.437 4.047 2.024 2.165 1.924 71,880 12,300 8.67
RS140H-2 1.750 1.000 1.000 0.252 1.661 1.433 0.500 4.327 2.163 2.343 2.055 94,370 16,300 11.01
RS160H-2 2.000 1.125 1.250 0.283 1.898 1.638 0.563 5.110 2.555 2.740 2.437 121,260 21,200 14.64
RS200H-2 2.500 1.563 1.500 0.374 2.374 2.047 0.781 6.461 3.230 3.437 3.083 207,260 29,900 24.51
RS240H-2 3.000 1.875 1.875 0.500 2.850 2.457 0.937 8.291 4.146 4.445 3.985 304,280 43,000 38.47
Triple Strand
RS60H-3 0.750 0.469 0.500 0.126 0.713 0.614 0.235 3.217 1.608 1.691 1.028 29,760 5,500 3.60
RS80H-3 1.000 0.625 0.625 0.157 0.949 0.819 0.313 4.012 2.006 2.108 1.283 52,920 9,000 6.21
RS100H-3 1.250 0.750 0.750 0.189 1.185 1.024 0.376 4.803 2.402 2.504 1.539 79,380 13,700 9.10
RS120H-3 1.500 0.875 1.000 0.220 1.425 1.228 0.437 5.972 2.986 3.132 1.924 107,820 18,100 12.99
RS140H-3 1.750 1.000 1.000 0.252 1.661 1.433 0.500 6.390 3.195 3.356 2.055 141,550 23,900 16.48
RS160H-3 2.000 1.125 1.250 0.283 1.898 1.638 0.563 7.555 3.778 3.955 2.437 181,890 31,200 21.93
RS200H-3 2.500 1.563 1.500 0.374 2.374 2.047 0.781 9.547 4.774 4.982 3.083 310,890 44,000 36.81
Notes:
RS240H-3 3.000 1.875 1.875 0.500 2.850 2.457 0.937 12.287 6.144 6.439 3.985 456,420 63,200 57.33
1. Riveted type chain will be provided unless otherwise specified. Cotter pin type chain will be provided upon request.

Drive Chain A50 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

Super Series
e
c

Heavy Duty Roller Chain

t
i
o
n

A
T

T
L1

φR
φD
W
L2

L1

L1
C
C
L2

C
L2
H

P P

Link Plate Pin

Width
Between Average Maximum
Roller Inner Link Transverse Tensile Allowable Approx.
Chain Pitch Dia. Plates Thickness Height Height Dia. Length Length Length Pitch Strength Load Weight
Number P R W T H h D L1 + L2 L1 L2 C (lbs.) (lbs.) (lbs./ft.)
Single Strand
SUPER80 1.000 0.625 0.625 0.126 0.949 0.819 0.313 1.398 0.640 0.758 - 19,140 4,180 1.9
SUPER100 1.250 0.750 0.750 0.157 1.185 1.024 0.376 1.677 0.778 0.900 - 28,600 6,820 2.9
SUPER120 1.500 0.875 1.000 0.189 1.425 1.228 0.437 2.118 0.980 1.138 - 41,800 8,800 4.2
SUPER140 1.750 1.000 1.000 0.220 1.661 1.433 0.500 2.307 1.059 1.248 - 55,000 12,100 5.4
SUPER160 2.000 1.125 1.250 0.252 1.898 1.638 0.563 2.705 1.254 1.451 - 70,400 15,840 7.2
SUPER200 2.500 1.562 1.500 0.315 2.374 2.047 0.781 3.299 1.535 1.764 - 113,300 21,120 11.8
SUPER240 3.000 1.875 1.875 0.374 2.850 2.457 0.937 4.071 1.886 2.185 - 165,000 29,700 17.2
Double Strand
SUPER80-2 1.000 0.625 0.625 0.126 0.949 0.819 0.313 2.551 1.217 1.335 1.154 38,280 7,106 3.8
SUPER100-2 1.250 0.750 0.750 0.157 1.185 1.024 0.376 3.091 1.484 1.606 1.409 57,200 11,594 5.6
SUPER120-2 1.500 0.875 1.000 0.189 1.425 1.228 0.437 3.906 1.874 2.031 1.787 83,600 14,990 8.3
SUPER140-2 1.750 1.000 1.000 0.220 1.661 1.433 0.500 4.232 2.022 2.211 1.925 110,000 20,570 10.7
SUPER160-2 2.000 1.125 1.250 0.252 1.898 1.638 0.563 5.012 2.407 2.604 2.303 140,800 26,928 14.4
SUPER200-2 2.500 1.562 1.500 0.315 2.374 2.047 0.781 6.122 2.947 3.175 2.819 226,600 35,904 23.4
SUPER240-2 3.000 1.875 1.875 0.374 2.850 2.457 0.937 7.531 3.618 3.913 3.457 330,000 50,490 34.0
Triple Strand
SUPER80-3 1.000 0.625 0.625 0.126 0.949 0.819 0.313 3.705 1.795 1.909 1.154 57,420 10,450 5.6
SUPER100-3 1.250 0.750 0.750 0.157 1.185 1.024 0.376 4.504 2.191 2.313 1.409 85,800 17,050 8.4
SUPER120-3 1.500 0.875 1.000 0.189 1.425 1.228 0.437 5.701 2.772 2.929 1.787 125,400 22,000 12.5
SUPER140-3 1.750 1.000 1.000 0.220 1.661 1.433 0.500 6.165 2.986 3.179 1.925 165,000 30,250 16.0
SUPER160-3 2.000 1.125 1.250 0.252 1.898 1.638 0.563 7.319 3.561 3.758 2.303 211,200 39,600 21.5
SUPER200-3 2.500 1.562 1.500 0.315 2.374 2.047 0.781 8.720 4.360 4.585 2.819 339,900 52,800 35.1

Notes:
SUPER240-3 3.000 1.875 1.875 0.374 2.850 2.457 0.937 10.697 5.348 5.636 3.457 495,000 74,250 51.0

1. Four pitch offset link is available for single strand.

2. riveted type chain will be provided unless otherwise specified. Roll pin type chain will be provided upon request.
3. Semi press-fit type connecting links will be supplied.

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A51
 Heavy Duty
Roller Chain

Super Series-Size 80 and 100

e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

Super 80 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 25 50 100 200 300 400 500 600 700 800 900 1000
Small Lubrication System
Sprocket A B C
13 2.4 4.5 8.4 15.7 22.6 29.2 35.8 42.2 43.3 35.4 29.6
14 2.6 4.9 9.1 17.0 24.5 31.8 38.7 45.7 48.4 39.5 33.1
15 2.8 5.3 9.8 18.4 26.4 34.2 41.8 49.2 53.6 43.8 36.7
16 3.0 5.6 10.5 19.6 28.3 36.6 44.8 52.8 59.1 48.4 40.5
17 3.2 6.0 11.2 20.9 30.2 39.1 47.8 56.3 64.7 52.9 44.4

18 3.4 6.4 11.9 22.2 32.2 41.5 50.8 59.9 68.7 57.6 48.4
19 3.6 6.8 12.7 23.6 34.0 44.1 53.9 63.5 72.9 62.6 52.4
20 3.8 7.2 13.4 24.9 35.9 46.6 57.0 67.1 77.1 67.5 56.5 48.4
21 4.0 7.6 14.1 26.3 37.9 49.2 60.0 70.8 81.2 72.8 61.0 52.0
22 4.3 7.9 14.9 27.7 39.8 51.6 63.1 74.4 85.5 78.0 65.4 55.7

24 4.7 8.7 16.3 30.4 43.8 56.7 69.4 81.7 93.9 88.8 74.5 63.5
26 5.1 9.5 17.8 33.1 47.7 61.9 75.6 89.1 102.4 100.2 84.0 71.7
30 5.9 11.1 20.8 38.7 55.7 72.2 88.3 104.0 119.4 124.2 104.1 88.8
32 6.4 11.9 22.2 41.5 59.8 77.5 94.6 111.5 128.1 136.7 114.7 98.0
35 7.0 13.1 24.5 45.7 65.8 85.2 104.3 122.7 140.7 156.8 131.2 112.0

40 8.1 15.1 28.3 52.8 76.0 98.5 120.3 142.0 163.5 183.6 159.5 136.7

Super 100 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 10 25 50 100 150 200 300 400 500 600 700 800 900
Small Lubrication System
Sprocket A B C
13 1.9 4.4 8.3 15.4 22.2 28.8 41.4 53.6 65.5 65.3 51.7
14 2.1 4.8 8.9 16.8 24.0 31.1 44.9 58.2 71.0 72.9 57.9
15 2.3 5.2 9.6 18.0 25.9 33.5 48.4 62.6 76.5 80.8 64.2 52.4
16 2.4 5.5 10.3 19.3 27.7 35.9 51.9 67.1 82.0 89.0 70.6 57.8
17 2.6 5.9 11.0 20.6 29.6 38.5 55.3 71.7 87.6 97.6 77.3 63.2

18 2.8 6.3 11.7 21.8 31.5 40.9 58.8 76.2 93.1 106.3 84.3 69.0
19 2.9 6.7 12.4 23.2 33.4 43.3 62.4 80.8 98.8 115.2 91.4 74.8
20 3.1 7.0 13.1 24.5 35.4 45.8 65.9 85.4 104.4 123.0 98.8 80.8
21 3.3 7.4 13.8 25.9 37.3 48.2 69.5 90.0 110.0 129.7 106.3 869.7
22 3.4 7.8 14.6 27.2 39.1 50.8 73.0 94.7 115.8 136.7 113.9 93.3
24 3.8 8.6 15.9 29.9 43.0 55.7 80.3 104.0 127.2 150.1 129.8 106.3
26 4.1 9.4 17.4 32.6 46.9 60.7 87.5 113.4 138.0 163.5 146.1 119.8
30 4.8 10.9 20.4 38.1 54.8 70.9 102.1 132.4 162.1 190.3 180.9 147.4
32 5.1 11.7 21.8 40.7 58.7 76.0 109.5 142.0 172.9 205.0 199.7 163.5 136.7
35 5.7 12.9 24.1 44.9 64.7 83.8 120.6 156.8 191.6 225.1 227.8 186.3 156.8

Notes:
40 6.5 14.9 27.7 51.9 74.6 96.7 139.4 180.9 221.1 260.0 278.7 227.8 191.6

1. Multiply the value given above by the multi-strand factor in order to obtain the horsepower rating of multi-strand chain.
2. Refer to roller chain maintenance section for more information on lubrication systems and methods.

Drive Chain A52 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

Super Series-Size 120 and 140

e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

Super 120 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 10 25 50 100 150 200 300 350 400 450 500 600 700 800
Small Lubrication System
Sprocket A B C
13 3.3 7.5 13.9 26.0 37.5 48.6 69.9 80.4 90.7 100.9 99.2 75.4
14 3.6 8.1 15.1 28.3 40.6 52.7 75.8 87.1 98.2 109.2 110.8 84.3
15 3.8 8.7 16.3 30.4 43.8 56.7 81.7 93.8 105.9 117.7 122.9 93.5
16 4.1 9.4 17.4 32.6 46.9 60.8 87.6 100.6 113.5 126.2 135.3 103.0
17 4.4 10.0 18.6 34.8 50.1 65.0 93.5 107.5 121.1 135.3 147.4 112.8 89.5

18 4.7 10.6 19.8 37.0 53.3 69.0 99.4 114.3 128.9 143.4 158.1 122.9 97.6
19 4.9 11.3 21.0 39.3 56.5 73.2 105.5 121.1 136.7 151.4 167.5 133.3 105.7
20 5.2 11.9 22.2 41.5 59.8 77.5 111.5 128.1 144.7 160.8 176.9 143.4 114.3
21 5.5 12.6 23.5 43.7 63.0 81.6 117.5 135.3 152.8 168.8 186.3 154.1 122.9
22 5.8 13.2 24.7 46.0 66.2 85.8 123.5 142.0 159.5 178.2 195.6 166.2 131.9

24 6.4 14.5 27.1 50.5 72.8 94.2 135.3 155.4 175.5 195.6 214.4 188.9 150.1
26 6.9 15.8 29.5 55.1 79.3 102.8 147.4 170.2 191.6 213.1 234.5 213.1 168.8
30 8.1 18.5 34.4 64.3 92.6 119.9 172.9 198.3 223.8 249.2 273.4 264.0 209.0
32 8.7 19.8 37.0 68.9 99.3 128.6 184.9 213.1 239.9 266.7 293.5 290.8 230.5
35 9.6 21.8 40.7 75.8 109.3 142.0 203.7 234.5 264.0 293.5 322.9 332.3 264.0

40 11.0 25.2 47.0 87.6 126.2 163.5 235.8 270.7 305.5 339.0 373.9 407.4 322.9 264.0

Super 140 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 10 25 50 100 150 200 250 300 350 400 450 500 550 600 650 700
Small Lubrication System
Sprocket A B C
13 4.7 10.7 20.0 37.3 53.6 69.5 85.0 100.1 115.0 129.7 131.5 112.2 97.3
14 5.1 11.6 21.6 40.3 58.2 75.3 92.1 108.4 124.6 140.7 146.1 125.4 108.7
15 5.5 12.5 23.3 43.4 62.6 81.1 99.2 116.8 134.0 151.4 162.1 138.0 120.6
16 5.9 13.4 24.9 46.6 67.1 87.0 106.3 125.3 143.4 162.1 179.6 152.8 132.8
17 6.3 14.3 26.7 49.7 71.7 92.9 113.5 133.7 154.1 172.9 193.0 167.5 144.7 127.6

18 6.7 15.1 28.4 52.9 76.2 98.8 120.7 142.0 163.5 184.9 205.0 182.2 158.1 138.0
19 7.1 16.1 30.0 56.1 80.8 104.7 128.0 151.4 172.9 195.6 217.1 197.0 171.5 150.1
20 7.5 17.0 31.8 59.4 85.5 110.7 135.3 159.5 183.6 206.4 229.1 214.4 184.9 162.1
21 7.9 18.0 33.5 62.6 90.0 116.7 142.0 167.5 193.0 217.1 242.5 230.5 199.7 175.5
22 8.3 18.9 35.2 65.8 94.7 122.7 150.1 176.9 202.3 229.1 254.6 246.6 214.4 187.6

24 9.1 20.8 38.7 72.2 104.0 135.3 164.8 194.3 222.4 251.9 280.1 281.4 243.9 214.4
26 9.9 22.6 42.2 78.8 113.4 147.4 179.6 211.7 242.5 274.7 304.2 317.6 274.7 241.2
30 11.6 26.4 49.3 91.9 132.4 171.5 209.0 246.6 284.1 320.3 356.4 391.3 340.4 298.8 265.3
32 12.4 28.3 52.8 98.5 142.0 183.6 225.1 265.3 304.2 343.0 381.9 419.4 375.2 329.6 292.1
35 13.7 31.2 58.2 108.5 156.8 202.3 247.9 292.1 335.0 377.9 420.8 462.3 428.8 376.5 333.7 298.8

Notes:
40 15.8 36.0 67.1 125.4 180.9 234.5 285.4 337.7 387.3 436.8 485.1 533.3 525.3 461.0 408.7 365.8

1. Multiply the value given above by the multi-strand factor in order to obtain the horsepower rating of multi-strand chain.
2. Refer to roller chain maintenance section for more information on lubrication systems and methods.

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A53
 Heavy Duty
Roller Chain

Super Series-Size 160 and 200

e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

Super 160 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 10 15 25 40 50 80 100 150 200 250 300 350 400 450 500 550
Small Lubrication System
Sprocket A B C
13 7.0 10.2 16.1 24.5 30.0 45.8 56.0 80.7 104.5 127.7 150.1 172.9 174.2 146.1 124.9
14 7.6 11.0 17.4 26.7 32.6 49.6 60.7 87.4 113.2 138.0 163.5 187.6 194.3 163.5 139.4
15 8.2 11.9 18.8 28.7 35.0 53.5 65.4 94.2 121.9 148.7 175.5 202.3 215.7 180.9 154.1
16 8.8 12.7 20.1 30.7 37.5 57.4 70.1 100.9 130.8 159.5 188.9 217.1 238.5 199.7 170.2
17 9.4 13.5 21.4 32.8 40.1 61.2 74.8 107.7 139.4 170.2 201.0 230.5 260.0 218.4 186.3

18 10.0 14.5 22.9 35.9 42.6 65.1 79.6 114.7 148.7 180.9 214.4 245.2 277.4 237.2 202.3
19 10.6 15.3 24.3 37.0 45.3 69.0 84.4 121.5 158.1 193.0 226.5 260.0 293.5 257.3 219.8 190.3
20 11.2 16.2 25.6 39.1 47.8 73.0 89.2 128.5 166.2 203.7 239.9 276.0 310.9 278.7 237.2 206.4
21 11.8 17.0 27.1 41.3 50.4 76.9 94.1 135.3 175.5 214.4 253.3 290.8 327.0 300.2 255.9 221.1
22 12.4 18.0 28.4 43.3 52.9 80.9 98.9 142.0 184.9 225.1 265.3 305.5 344.4 321.6 274.7 237.2

24 13.7 19.7 31.2 47.6 58.2 88.8 108.5 156.8 202.3 247.9 292.1 335.0 377.9 365.8 312.2 270.7
26 14.9 21.4 34.0 51.9 63.5 96.9 118.5 170.2 221.1 270.7 318.9 365.8 412.7 412.7 352.4 305.5
30 17.4 25.1 39.7 60.6 74.1 113.1 138.0 199.7 257.3 314.9 371.2 426.1 481.1 511.9 436.8 379.2
32 18.6 26.9 42.6 65.0 79.5 121.3 148.7 213.1 276.0 337.7 398.0 456.9 515.9 564.1 482.4 418.1
35 20.5 29.6 46.9 71.6 87.5 133.5 163.5 234.5 304.2 372.5 438.2 503.8 568.2 632.5 550.7 477.0

40 23.7 34.2 54.1 82.7 101.0 154.1 188.9 272.0 352.4 430.1 506.5 581.6 656.6 730.3 674.0 584.2

Super 200 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 5 10 15 20 25 30 40 50 60 80 100 150 200 250
Small Lubrication System
Sprocket A B C
13 6.5 12.2 17.6 22.6 27.7 32.7 42.3 51.7 61.0 79.1 96.6 139.4 180.9 219.8
14 7.1 13.2 19.0 24.7 30.0 35.4 45.8 56.1 66.1 85.6 104.7 151.4 195.6 238.5
15 7.6 14.2 20.5 26.5 32.4 38.2 49.4 60.4 71.2 92.2 112.8 162.1 210.4 257.3
16 8.2 15.3 22.0 28.4 34.7 40.9 53.1 64.9 76.4 98.9 120.9 174.2 225.1 276.0
17 8.7 16.2 23.5 30.4 37.1 43.7 56.5 69.1 81.5 105.6 129.0 186.3 241.2 294.8

18 9.3 17.3 24.9 32.3 39.4 46.5 60.2 73.6 86.7 112.3 136.7 198.3 255.9 313.6
19 9.8 18.4 26.4 34.2 41.8 49.3 63.8 78.0 91.9 119.1 146.1 209.0 272.0 332.3
20 10.4 19.4 27.9 36.2 44.2 52.1 67.4 82.4 97.2 125.8 154.1 221.1 286.8 351.1
21 10.9 20.4 29.5 38.1 46.6 54.9 71.2 87.0 102.4 132.7 162.1 233.2 302.8 369.8
22 11.5 21.4 31.0 40.1 49.0 57.8 74.8 91.4 107.7 139.4 170.2 253.3 317.6 388.6

24 12.6 23.6 34.0 44.0 53.9 63.4 82.1 100.4 118.3 152.8 187.6 269.3 349.7 427.5
26 13.8 25.7 37.0 48.0 58.7 69.1 89.5 109.5 129.0 167.5 203.7 294.8 380.6
30 16.1 30.0 43.3 56.0 68.5 80.7 104.5 127.7 150.1 195.6 238.5 343.0 444.9
32 17.3 32.2 46.4 60.0 73.4 86.4 112.0 136.7 160.8 209.0 255.9 368.5 477.0
35 19.0 35.5 51.1 66.2 80.8 95.3 123.4 151.4 178.2 230.5 281.4 406.0 361.8

Notes:
40 22.0 41.0 59.0 76.4 93.4 110.0 142.0 174.2 205.0 266.7 325.6 469.0 394.0

1. Multiply the value given above by the multi-strand factor in order to obtain the horsepower rating of multi-strand chain.
2. Refer to roller chain maintenance section for more information on lubrication systems and methods.

Drive Chain A54 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

Super Series-Size 240

e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

Super 240 Maximum Horsepower Ratings

Number of Maximum Speed - Small Sprocket (rpm)
Teeth 5 10 15 20 25 30 40 50 60 80 100 125 150
Small Lubrication System
Sprocket A B C
13 8.0 15.0 21.6 28.0 34.2 40.3 52.2 63.8 75.2 97.5 119.0 146.0 112.0
14 8.7 16.3 23.4 30.3 37.1 43.7 56.6 69.2 81.5 106.0 129.0 158.0 118.0
15 9.4 17.5 25.2 32.7 39.9 47.1 61.0 74.5 87.8 114.0 139.0 170.0 126.0
16 10.1 18.8 27.0 35.0 42.8 50.4 65.4 79.9 94.1 122.0 149.0 182.0 133.0
17 10.7 20.0 28.9 37.4 45.7 53.9 69.8 85.3 101.0 130.0 159.0 195.0 139.0

18 11.4 21.3 30.7 39.8 48.6 57.3 74.2 90.7 107.0 138.0 169.0 207.0 146.0
19 12.1 22.6 32.5 42.2 51.5 60.7 78.7 96.2 113.0 147.0 179.0 219.0 153.0
20 12.8 23.9 34.4 44.6 54.5 64.2 83.2 102.0 120.0 155.0 190.0 232.0 159.0
21 13.5 25.2 36.3 47.0 57.4 67.7 87.7 107.0 126.0 164.0 200.0 244.0 165.0
22 14.2 26.5 38.1 49.4 60.4 71.2 92.2 113.0 133.0 172.0 210.0 257.0

24 15.6 29.1 41.9 54.3 66.3 78.2 101.0 124.0 146.0 189.0 231.0 282.0
26 17.0 31.7 45.7 59.2 72.3 85.2 110.0 135.0 159.0 206.0 252.0 308.0
30 19.8 37.0 53.3 69.1 84.4 99.5 129.0 158.0 186.0 240.0 294.0 215.0
32 21.3 39.7 57.1 74.0 90.5 107.0 138.0 169.0 199.0 258.0 315.0 225.0
35 23.4 43.7 63.0 81.6 99.7 117.0 152.0 186.0 219.0 284.0 347.0

Notes:
40 27.1 50.5 72.7 94.2 115.0 136.0 176.0 215.0 253.0 328.0 259.0

1. Multiply the value given above by the multi-strand factor in order to obtain the horsepower rating of multi-strand chain.
2. Refer to roller chain maintenance section for more information on lubrication systems and methods.

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A55
 Heavy Duty
Roller Chain

HT Series
e
c

Heavy Duty Roller Chain

t
i
o
n

A
T

T
L1

φD φR
W
L2

L1
L1

C
C
L2

C
L2
H
h

P P

All dimensions in inches unless otherwise stated.

Link Plate Pin
Width
Between Average Maximum
Roller Inner Link Transverse Tensile Allowable Approx.
Chain Pitch Dia. Plates Thickness Height Height Dia. Length Length Length Pitch Strength Load Weight
Number P R W T H h D L 1 + L2 L1 L2 C (lbs.) (lbs.) (lbs./ft.)
Single Strand
RS40HT 0.500 0.312 0.312 0.080 0.472 0.409 0.156 0.808 0.375 0.433 - 5,290 1,170 0.5
RS50HT 0.625 0.400 0.375 0.094 0.591 0.512 0.200 0.941 0.437 0.504 - 8,260 1,870 0.8
RS60HT 0.750 0.469 0.500 0.126 0.713 0.614 0.235 1.252 0.583 0.669 - 12,540 2,200 1.2
RS80HT 1.000 0.625 0.625 0.157 0.949 0.819 0.313 1.543 0.720 0.823 - 20,900 3,630 2.1
RS100HT 1.250 0.750 0.750 0.189 1.185 1.024 0.376 1.823 0.858 0.965 - 31,900 5,500 3.1
RS120HT 1.500 0.875 1.000 0.220 1.425 1.228 0.437 2.264 1.061 1.203 - 42,900 7,260 4.4
RS140HT 1.750 1.000 1.000 0.252 1.661 1.433 0.500 2.441 1.138 1.303 - 56,100 9,570 5.5
RS160HT 2.000 1.125 1.250 0.281 1.898 1.638 0.563 2.850 1.337 1.514 - 71,500 12,540 7.4
RS200HT 2.500 1.562 1.500 0.374 2.374 2.047 0.781 3.583 1.689 1.894 - 125,400 17,600 12.3
RS240HT 3.000 1.875 1.875 0.500 2.850 2.457 0.937 4.610 2.157 2.453 - 198,000 25,300 19.5
Double Strand
RS60HT-2 0.750 0.469 0.500 0.126 0.713 0.614 0.235 2.272 1.094 1.177 1.028 25,080 3,740 2.4
RS80HT-2 1.000 0.625 0.625 0.157 0.949 0.819 0.313 2.827 1.362 1.465 1.283 41,800 6,100 4.1
RS100HT-2 1.250 0.750 0.750 0.189 1.185 1.024 0.376 3.366 1.630 1.736 1.539 63,800 9,350 6.1
RS120HT-2 1.500 0.875 1.000 0.220 1.425 1.228 0.437 4.189 2.024 2.165 1.925 85,800 12,340 8.6
RS140HT-2 1.750 1.000 1.000 0.252 1.661 1.433 0.500 4.506 2.163 2.343 2.055 112,200 16,280 11.0
RS160HT-2 2.000 1.125 1.250 0.281 1.898 1.638 0.563 5.295 2.555 2.740 2.437 143,000 21,310 14.6
RS200HT-2 2.500 1.562 1.500 0.374 2.374 2.047 0.781 6.667 3.230 3.437 3.083 250,800 29,920 24.4
RS240HT-2 3.000 1.875 1.875 0.500 2.850 2.457 0.937 8.591 4.146 4.445 3.984 396,000 43,010 38.4
Triple Strand
RS60HT-3 0.750 0.469 0.500 0.126 0.713 0.614 0.235 3.299 1.608 1.691 1.028 37,620 5,500 3.6
RS80HT-3 1.000 0.625 0.625 0.157 0.949 0.819 0.313 4.114 2.006 2.108 1.283 62,700 9,080 6.2
RS100HT-3 1.250 0.750 0.750 0.189 1.185 1.024 0.376 4.906 2.402 2.504 1.539 95,700 13,750 9.1
RS120HT-3 1.500 0.875 1.000 0.220 1.425 1.228 0.437 6.118 2.986 3.132 1.925 128,700 18,150 13.0
RS140HT-3 1.750 1.000 1.000 0.252 1.661 1.433 0.500 6.551 3.195 3.356 2.055 168,300 23,930 16.4
RS160HT-3 2.000 1.125 1.250 0.281 1.898 1.638 0.563 7.732 3.778 3.955 2.437 214,500 31,350 21.9
RS200HT-3 2.500 1.562 1.500 0.374 2.374 2.047 0.781 9.756 4.774 4.982 3.083 376,200 44,000 36.7

Notes:
RS240HT-3 3.000 1.875 1.875 0.500 2.850 2.457 0.937 12.583 6.144 6.439 3.984 594,000 63,250 57.3

1. riveted type chain will be provided unless otherwise specified. Cottered type chain is available upon request.
2. Semi-press fit connecting links will be supplied.

Drive Chain A56 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

HT Series-Size
e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

60HT Maximum Horsepower Ratings

Number Maximum Speed - Small Sprocket (RPM)
of Teeth 10 25 50 100 150 200 300 400 500 600 700 800 900 1000 1100 1200
on Small Lubrciation System
Sprocket A B C
9 0.36 0.81 1.51 2.83 4.07 5.27 7.59 9.84 12.03 13.5 13.5 13.5 13.5
10 0.40 0.91 1.70 3.17 4.56 5.91 8.51 11.02 13.5 15.3 15.3 15.3 15.3
11 0.44 1.01 1.88 3.51 5.05 6.55 9.43 12.22 14.9 17.0 17.0 17.0 17.0
12 0.49 1.11 2.07 3.86 5.55 7.19 10.36 13.4 16.4 18.6 18.6 18.6 18.6
13 0.53 1.21 2.25 4.20 6.05 7.84 11.30 14.6 17.9 20.4 20.4 20.4 20.4
14 0.57 1.31 2.44 4.55 6.56 8.50 12.24 15.9 19.4 22.4 22.4 22.4 22.4 22.4
15 0.62 1.41 2.63 4.91 7.07 9.15 13.19 17.1 20.9 24.6 24.8 24.8 24.8 24.8
16 0.66 1.51 2.82 5.26 7.58 9.82 14.1 18.3 22.4 26.4 27.3 27.3 27.3 27.3
17 0.71 1.61 3.01 5.62 8.09 10.48 15.1 19.6 23.9 28.2 29.9 29.9 29.9 29.9
18 0.75 1.72 3.20 5.97 8.60 11.15 16.1 20.8 25.4 30.0 31.8 31.8 31.8 31.8
19 0.80 1.82 3.39 6.33 9.12 11.82 17.0 22.1 27.0 31.8 33.6 33.6 33.6 33.6
20 0.84 1.92 3.59 6.69 9.64 12.49 18.0 23.3 28.5 33.6 35.6 35.6 35.6 35.6
21 0.89 2.03 3.78 7.06 10.16 13.17 19.0 24.6 30.0 35.4 37.5 37.5 37.5 37.5
22 0.93 2.13 3.98 7.42 10.69 13.8 19.9 25.8 31.6 37.2 39.5 39.5 39.5 39.5
23 0.98 2.24 4.17 7.78 11.21 14.5 20.9 27.1 33.1 39.0 41.4 41.4 41.4 41.4
24 1.03 2.34 4.37 8.15 11.74 15.2 21.9 28.4 34.7 40.9 43.6 43.6 43.6 43.6 43.6
25 1.07 2.45 4.56 8.52 12.27 15.9 22.9 29.7 36.3 42.7 46.2 46.2 46.2 46.2 46.2
26 1.12 2.55 4.76 8.89 12.80 16.6 23.9 30.9 37.8 44.6 49.0 49.0 49.0 49.0 49.0
28 1.21 2.76 5.16 9.63 13.9 18.0 25.9 33.5 41.0 48.3 54.8 54.8 54.8 54.8 54.8
30 1.31 2.98 5.56 10.37 14.9 19.4 27.9 36.1 44.1 52.0 59.8 60.2 60.2 60.2 60.2
32 1.40 3.19 5.96 11.12 16.0 20.7 29.9 38.7 47.3 55.8 64.1 64.5 64.5 64.5 64.5
35 1.54 3.52 6.56 12.25 17.6 22.9 32.9 42.7 52.1 61.4 70.6 71.0 71.0 71.0 71.0
40 1.78 4.06 7.58 14.1 20.4 26.4 38.0 49.3 60.2 71.0 81.5 82.1 82.1 82.1 82.1 82.1

80HT Maximum Horsepower Ratings

45 2.02 4.61 8.61 16.1 23.1 30.0 43.2 56.0 68.4 80.6 92.6 98.1 98.1 98.1 98.1 98.1

Number Maximum Speed - Small Sprocket (RPM)

of Teeth 10 25 50 100 150 200 300 400 500 600 700
on Small Lubrciation System
Sprocket A B C
9 0.78 1.79 3.33 6.22 8.96 11.61 16.7 21.7 24.4 24.4
10 0.88 2.00 3.74 6.97 10.04 13.01 18.7 24.3 27.3 27.3
11 0.97 2.22 4.14 7.73 11.13 14.4 20.8 26.9 30.3 30.3
12 1.07 2.44 4.55 8.49 12.23 15.8 22.8 29.6 33.4 33.4
13 1.17 2.66 4.96 9.25 13.33 17.3 24.9 32.2 36.3 36.3
14 1.26 2.88 5.37 10.03 14.4 18.7 26.9 34.9 39.4 39.4
15 1.36 3.10 5.79 10.80 15.6 20.2 29.0 37.6 43.7 43.7
16 1.46 3.33 6.21 11.58 16.7 21.6 31.1 40.3 48.1 48.1
17 1.56 3.55 6.63 12.36 17.8 23.1 33.2 43.1 52.7 52.7
18 1.66 3.78 7.05 13.15 18.9 24.5 35.4 45.8 56.0 57.4
19 1.76 4.00 7.47 13.9 20.1 26.0 37.5 48.6 59.4 61.6
20 1.86 4.23 7.90 14.7 21.2 27.5 39.6 51.3 62.7 65.3
21 1.96 4.46 8.32 15.5 22.4 29.0 41.8 54.1 66.1 68.7
22 2.06 4.69 8.75 16.3 23.5 30.5 43.9 56.9 69.5 72.2
23 2.16 4.92 9.18 17.1 24.7 32.0 46.1 59.7 73.0 75.8
24 2.26 5.15 9.62 17.9 25.8 33.5 48.2 62.5 76.4 79.5
25 2.36 5.39 10.05 18.8 27.0 35.0 50.4 65.3 79.8 82.9
26 2.46 5.62 10.48 19.6 28.2 36.5 52.6 68.1 83.3 86.6
28 2.67 6.09 11.36 21.2 30.5 39.6 57.0 73.8 90.2 93.8
30 2.87 6.56 12.24 22.8 32.9 42.6 61.4 79.5 97.2 103.4
32 3.08 7.03 13.12 24.5 35.3 45.7 65.8 85.3 104.2 113.9 113.9
35 3.40 7.75 14.5 27.0 38.8 50.3 72.5 93.9 114.8 130.4 130.4
40 3.92 8.95 16.7 31.2 44.9 58.1 83.7 108.5 132.6 153 153
45 4.45 10.16 19.0 35.4 51.0 66.0 95.1 123.2 151 174 174

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A57
 Heavy Duty
Roller Chain

HT Series-Size
e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9

100HT Maximum Horsepower Ratings

6 4.6

Number Maximum Speed - Small Sprocket (RPM)

of Teeth 10 25 50 100 150 200 300 400 500
on Small Lubrciation System
Sprocket A B C
9 1.48 3.38 6.30 11.76 16.9 21.9 31.6 35.4
10 1.66 3.78 7.06 13.18 19.0 24.6 35.4 39.7
11 1.84 4.19 7.83 14.6 21.0 27.3 39.3 44.0
12 2.02 4.61 8.60 16.0 23.1 29.9 43.1 48.4
13 2.20 5.02 9.38 17.5 25.2 32.6 47.0 52.7
14 2.39 5.44 10.16 19.0 27.3 35.4 50.9 57.5
15 2.57 5.86 10.94 20.4 29.4 38.1 54.9 63.8
16 2.76 6.29 11.73 21.9 31.5 40.9 58.8 70.2
17 2.94 6.71 12.53 23.4 33.7 43.6 62.8 76.9 76.9
18 3.13 7.14 13.32 24.9 35.8 46.4 66.8 83.8 83.8
19 3.32 7.57 14.1 26.4 38.0 49.2 70.8 90.9 90.9
20 3.51 8.00 14.9 27.9 40.1 52.0 74.9 96.3 96.3
21 3.70 8.43 15.7 29.4 42.3 54.8 78.9 101.6 101.6
22 3.89 8.87 16.5 30.9 44.5 57.6 83.0 106.8 106.8
23 4.08 9.30 17.4 32.4 46.7 60.5 87.1 112.2 112.2
24 4.27 9.74 18.2 33.9 48.9 63.3 91.2 117.4 117.4
25 4.46 10.18 19.0 35.5 51.1 66.2 95.3 122.6 122.6
26 4.66 10.62 19.8 37.0 53.3 69.0 99.4 128.0 128.0
28 5.04 11.51 21.5 40.1 57.7 74.8 107.7 138 138
30 5.43 12.40 23.1 43.2 62.2 80.6 116.0 149 149
32 5.83 13.29 24.8 46.3 66.7 86.4 124.4 161 162
35 6.42 14.6 27.3 51.0 73.4 95.1 137 178 186
40 7.41 16.9 31.6 58.9 84.8 109.9 158 205 228

120HT Maximum Horsepower Ratings

45 8.42 19.2 35.8 66.9 96.3 124.8 180 233 263

Number Maximum Speed - Small Sprocket (RPM)

of Teeth 10 25 50 100 150 200 300 400 500
on Small Lubrciation System
Sprocket A B C
9 2.35 5.36 10.00 18.7 26.9 34.8 50.2 55.1
10 2.63 6.01 11.21 20.9 30.1 39.0 56.2 61.8
11 2.92 6.66 12.42 23.2 33.4 43.3 62.3 68.3
12 3.21 7.31 13.6 25.5 36.7 47.5 68.4 75.2
13 3.50 7.97 14.9 27.8 40.0 51.8 74.6 81.9
14 3.79 8.64 16.1 30.1 43.3 56.1 80.8 88.7
15 4.08 9.31 17.4 32.4 46.7 60.5 87.1 95.5
16 4.37 9.98 18.6 34.7 50.0 64.8 93.4 102.5
17 4.67 10.65 19.9 37.1 53.4 69.2 99.7 112.2
18 4.97 11.33 21.1 39.5 56.8 73.6 106.1 122.2
19 5.27 12.01 22.4 41.8 60.3 78.1 112.4 132.5
20 5.57 12.70 23.7 44.2 63.7 82.5 118.8 143
21 5.87 13.38 25.0 46.6 67.1 87.0 125.3 154 154
22 6.17 14.1 26.3 49.0 70.6 91.4 131.7 165 165
23 6.47 14.8 27.6 51.4 74.1 95.9 138 177 177
24 6.78 15.5 28.8 53.8 77.5 100.5 145 188 188
25 7.08 16.2 30.1 56.3 81.0 105.0 151 196 196
26 7.39 16.9 31.5 58.7 84.5 109.5 158 204 204
28 8.00 18.3 34.1 63.6 91.6 118.7 171 221 221
30 8.62 19.7 36.7 68.5 98.7 127.8 184 239 239
32 9.25 21.1 39.4 73.4 105.8 137 197 256 256
35 10.19 23.2 43.4 80.9 116.5 151 217 281 281
40 11.77 26.8 50.1 93.5 135 174 251 324 324
45 13.36 30.5 56.9 106.1 153 198 285 370 383

Drive Chain A58 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

HT Series-Size
e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

140HT Maximum Horsepower Ratings

Number Maximum Speed - Small Sprocket (RPM)
of Teeth 10 25 50 100 150 200 250 300 350 400 450
on Small Lubrciation System
Sprocket A B C
9 3.61 8.24 15.4 28.7 41.3 53.6 65.5 75.2 75.2
10 4.05 9.23 17.2 32.2 46.3 60.0 73.3 86.4 87.9
11 4.49 10.24 19.1 35.6 51.3 66.5 81.3 95.8 97.4
12 4.93 11.24 21.0 39.2 56.4 73.1 89.3 105.2 107.1
13 5.37 12.26 22.9 42.7 61.5 79.7 97.4 114.7 116.7
14 5.82 13.28 24.8 46.2 66.6 86.3 105.5 124.3 126.5
15 6.27 14.3 26.7 49.8 71.8 93.0 113.7 134 138
16 6.73 15.3 28.6 53.4 76.9 99.7 121.9 144 153
17 7.18 16.4 30.6 57.0 82.2 106.4 130.1 153 166
18 7.64 17.4 32.5 60.7 87.4 113.2 138 163 182 182
19 8.10 18.5 34.5 64.3 92.6 120.0 147 173 193 193
20 8.56 19.5 36.4 68.0 97.9 126.9 155 183 204 204
21 9.02 20.6 38.4 71.7 103.2 134 163 193 216 216
22 9.49 21.6 40.4 75.3 108.5 141 172 203 226 226
23 9.95 22.7 42.4 79.1 113.9 148 180 212 237 237
24 10.42 23.8 44.4 82.8 119.2 154 189 222 249 249
25 10.89 24.8 46.4 86.5 124.6 161 197 233 260 260
26 11.36 25.9 48.4 90.2 130.0 168 206 243 273 273
28 12.31 28.1 52.4 97.8 141 182 223 263 302 306
30 13.26 30.2 56.4 105.3 152 197 240 283 325 339
32 14.2 32.4 60.5 112.9 163 211 258 304 349 370
35 15.7 35.7 66.7 124.4 179 232 284 334 384 407
40 18.1 41.3 77.0 144 207 268 328 386 444 470

160HT Maximum Horsepower Ratings

45 20.5 46.9 87.5 163 235 305 372 439 504 547 547

160HT Maximum Speed - Small Sprocket (RPM)

Number
of Teeth 10 25 50 100 150 200 250 300 350 400
on Small Lubrciation System
Sprocket A B C
9 5.41 12.33 23.0 42.9 61.8 80.1 97.9 99.8
10 6.06 13.8 25.8 48.1 69.3 89.8 109.7 117.0
11 6.71 15.3 28.6 53.3 76.8 99.5 121.6 132.0
12 7.37 16.8 31.4 58.6 84.4 109.3 134 145
13 8.04 18.3 34.2 63.9 92.0 119.2 146 158
14 8.71 19.9 37.1 69.2 99.7 129.1 158 172
15 9.38 21.4 39.9 74.5 107.4 139 170 185
16 10.06 23.0 42.8 79.9 115.1 149 182 198
17 10.74 24.5 45.7 85.3 122.9 159 195 217
18 11.43 26.1 48.6 90.8 130.7 169 207 237 237
19 12.11 27.6 51.6 96.2 139 180 219 257 257
20 12.80 29.2 54.5 101.7 146 190 232 273 277
21 13.5 30.8 57.5 107.2 154 200 245 288 295
22 14.2 32.4 60.4 112.7 162 210 257 303 310
23 14.9 34.0 63.4 118.3 170 221 270 318 326
24 15.6 35.6 66.4 123.8 178 231 282 333 340
25 16.3 37.2 69.4 129.4 186 242 295 348 356
26 17.0 38.8 72.4 135 194 252 308 363 371
28 18.4 42.0 78.4 146 211 273 334 393 402
30 19.8 45.3 84.4 158 227 294 359 424 436
32 21.3 48.5 90.5 169 243 315 385 454 480
35 23.4 53.5 99.7 186 268 347 425 500 548 548
40 27.1 61.7 115.2 215 310 401 490 578 650 650
45 30.7 70.1 130.8 244 352 456 557 656 738 738

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A59
 Heavy Duty
Roller Chain

HT Series-Size
e
c

Maximum Horsepower Ratings

t
i
o
n

Multi Strand Factor

A

Lubricating Systems and Methods

Number of Multi-
Roller Chain Strand
Strands Factor
2 1.7 A Drip lubrication
3 2.5 B Oil bath lubrication or lubrication by slinger disc
4 3.3 C Lubrication using a pump
5 3.9
6 4.6

200HT Maximum Horsepower Ratings

Number Maximum Speed - Small Sprocket (RPM)
of Teeth 10 15 20 30 40 50 70 100 150 200 250 300
on Small Lubrciation System
Sprocket A B C
9 9.49 13.7 17.7 25.5 33.0 40.4 54.7 75.4 108.6 141 145
10 10.63 15.3 19.8 28.6 37.0 45.3 61.3 84.4 121.6 158 163
11 11.78 17.0 22.0 31.7 41.0 50.2 67.9 93.6 135 175 181
12 12.95 18.6 24.2 34.8 45.1 55.1 74.6 102.8 148 192 198
13 14.1 20.3 26.3 37.9 49.1 60.1 81.3 112.1 161 209 216
14 15.3 22.0 28.5 41.1 53.2 65.1 88.1 121.5 175 227 235
15 16.5 23.7 30.7 44.3 57.4 70.1 94.9 130.9 188 244 257
16 17.7 25.4 33.0 47.5 61.5 75.2 101.8 140 202 262 283
17 18.9 27.2 35.2 50.7 65.7 80.3 108.7 150 216 280 310
18 20.1 28.9 37.4 53.9 69.8 85.4 115.6 159 229 297 338 338
19 21.3 30.6 39.7 57.2 74.0 90.5 122.5 169 243 315 366 366
20 22.5 32.4 41.9 60.4 78.3 95.7 129.5 179 257 333 389 389
21 23.7 34.1 44.2 63.7 82.5 100.8 137 188 271 351 409 409
22 24.9 35.9 46.5 67.0 86.7 106.0 144 198 285 369 430 430
23 26.1 37.6 48.8 70.3 91.0 111.3 151 208 299 387 452 452
24 27.4 39.4 51.1 73.6 95.3 116.5 158 217 313 406 473 473
25 28.6 41.2 53.4 76.9 99.6 121.7 165 227 327 424 494 494

240HT Maximum Horsepower Ratings

26 29.8 43.0 55.7 80.2 103.9 127.0 172 237 341 442 516 516

Number Maximum Speed - Small Sprocket (RPM)

of Teeth 5 10 15 20 25 30 40 50 60 80 100 125 150 175 200 250
on Small Lubrciation System
Sprocket A B
9 8.78 16.4 23.6 30.6 37.4 44.1 57.1 69.8 82.2 106.5 130.2 159 188 213 213 0
10 9.84 18.4 26.5 34.3 41.9 49.4 64.0 78.2 92.1 119.3 146 178 210 241 245 245
11 10.91 20.4 29.3 38.0 46.4 54.7 70.9 86.6 102.1 132.3 162 198 233 268 271 271
12 11.98 22.4 32.2 41.7 51.0 60.1 77.9 95.2 112.2 145 178 217 256 294 297 297
13 13.07 24.4 35.1 45.5 55.6 65.5 84.9 103.8 122.3 158 194 237 279 320 324 324
14 14.2 26.4 38.0 49.3 60.2 71.0 92.0 112.4 132.5 172 210 256 302 347 352 352
15 15.2 28.5 41.0 53.1 64.9 76.5 99.1 121.1 143 185 226 276 326 374 379 379
16 16.3 30.5 43.9 56.9 69.6 82.0 106.2 129.9 153 198 242 296 349 401 401 401
17 17.5 32.6 46.9 60.8 74.3 87.6 113.4 139 163 212 259 316 373 402 402
18 18.6 34.6 49.9 64.7 79.0 93.1 120.7 147 174 225 275 336 396 406 406
19 19.7 36.7 52.9 68.5 83.8 98.7 127.9 156 184 239 292 357 420 425 425
20 20.8 38.8 55.9 72.4 88.6 104.4 135 165 195 252 308 377 442 442
21 21.9 40.9 58.9 76.4 93.4 110.0 143 174 205 266 325 397 462 462
22 23.1 43.0 62.0 80.3 98.2 115.7 150 183 216 280 342 418 464 464
23 24.2 45.1 65.0 84.3 103.0 121.4 157 192 226 293 359 438 496 496
24 25.3 47.3 68.1 88.2 107.8 127.1 165 201 237 307 376 459 531 531
25 26.5 49.4 71.2 92.2 112.7 132.8 172 210 248 321 392 480 549 549
26 27.6 51.5 74.2 96.2 117.6 139 179 219 259 335 409 500 560 560

Drive Chain A60 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]
 Heavy Duty
Roller Chain

Super-H Series
e
c

Heavy Duty Roller Chain

t
i
o
n

A
T

T
L1

φD φR
W

L1
L2

L1

C
C
L2

C
L2
H
h

P P

Link Plate Pin

Width
Between Average Maximum
Roller Inner Link Transverse Tensile Allowable Approx.
Pitch Dia. Plates Thickness Height Height Dia. Length Length Length Pitch Strength Load Weight
Chain Number P R W T H h D L 1 + L2 L1 L2 C (lbs.) (lbs.) (lbs./ft.)
Single Strand
SUPER80H 1.000 0.625 0.625 0.157 0.949 0.819 0.313 1.543 0.720 0.823 - 22,000 4,620 2.2
SUPER100H 1.250 0.750 0.750 0.189 1.185 1.024 0.376 1.823 0.858 0.965 - 32,560 7,260 3.3
SUPER120H 1.500 0.875 1.000 0.220 1.425 1.228 0.437 2.264 1.061 1.203 - 44,000 9,460 4.7
SUPER140H 1.750 1.000 1.000 0.252 1.661 1.433 0.500 2.441 1.138 1.303 - 57,200 12,760 6.0
SUPER160H 2.000 1.125 1.250 0.281 1.898 1.638 0.563 2.851 1.337 1.514 - 72,600 16,500 7.9
SUPER200H 2.500 1.500 1.500 0.374 2.374 2.047 0.781 3.583 1.689 1.894 - 134,200 22,400 13.2
SUPER240H 3.000 1.875 1.875 0.500 2.850 2.457 0.937 4.610 2.157 2.453 - 206,800 31,240 20.5
Double Strand
SUPER80H-2 1.000 0.625 0.625 0.157 0.949 0.819 0.313 2.823 1.358 1.465 1.283 44,000 7,854 4.4
SUPER100H-2 1.250 0.750 0.750 0.189 1.185 1.024 0.376 3.366 1.630 1.736 1.539 65,120 12,342 6.4
SUPER120H-2 1.500 0.875 1.000 0.220 1.425 1.228 0.437 4.179 2.014 2.165 1.925 88,000 16,082 9.1
SUPER140H-2 1.750 1.000 1.000 0.252 1.661 1.433 0.500 4.506 2.163 2.343 2.055 114,400 21,692 11.7
SUPER160H-2 2.000 1.125 1.250 0.281 1.898 1.638 0.563 5.295 2.555 2.740 2.437 145,200 28,050 15.4
SUPER200H-2 2.500 1.562 1.500 0.374 2.374 2.047 0.781 6.667 3.230 3.437 3.083 268,400 38,080 25.9
SUPER240H-2 3.000 1.875 1.875 0.500 2.850 2.457 0.937 8.591 4.146 4.445 3.984 413,600 53,108 40.2
Triple Strand
SUPER80H-3 1.000 0.625 0.625 0.157 0.949 0.819 0.313 4.106 1.998 2.108 1.283 66,000 11,550 6.6
SUPER100H-3 1.250 0.750 0.750 0.189 1.185 1.024 0.376 4.904 2.400 2.504 1.539 97,680 18,150 9.6
SUPER120H-3 1.500 0.875 1.000 0.220 1.425 1.228 0.437 6.086 2.954 3.132 1.925 132,000 23,650 13.6
SUPER140H-3 1.750 1.000 1.000 0.252 1.661 1.433 0.500 6.547 3.191 3.356 2.055 171,600 31,900 17.4
SUPER160H-3 2.000 1.125 1.250 0.281 1.898 1.638 0.563 7.711 3.756 3.955 2.437 217,800 41,250 23.0
SUPER200H-3 2.500 1.562 1.500 0.374 2.374 2.047 0.781 9.743 4.761 4.982 3.083 402,600 56,000 38.5

Notes:
SUPER240H-3 3.000 1.875 1.875 0.500 2.850 2.457 0.937 12.544 6.105 6.439 3.984 620,400 78,100 59.9

1. Offset links are not available.

2. riveted type chain will be provided unless otherwise specified. Roll pin type chain will be provided upon request.
3. Semi press-fit type connecting links will be supplied.

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] Drive Chain A61
 Heavy Duty
Roller Chain

Ultra Super Series

S
e
c

Heavy Duty Roller Chain

t
i
o
n

T
L1

φR
φD
L2

W
H

P P

All dimensions in inches unless otherwise stated.

Side Plates Pin
Width
Between Average Maximum
Roller Inner Link Tensile Allowable Approx.
Chain Pitch Dia. Plates Thickness Height Dia. Length Length Length Strength Load Weight
Number P R W T H D L 1 + L2 L1 L2 (lbs.) (lbs.) (lbs./ft.)
US100 1.250 0.750 0.750 0.187 1.185 0.406 1.878 0.880 0.998 38,500 8,800 3.40
US120 1.500 0.875 1.000 0.219 1.425 0.483 2.327 1.085 1.242 55,000 12,100 4.84
US140 1.750 1.000 1.000 0.250 1.661 0.550 2.508 1.161 1.346 70,400 14,300 6.19
US160 2.000 1.125 1.250 0.281 1.898 0.615 2.941 1.358 1.583 88,000 19,140 8.17
US200 2.500 1.562 1.500 0.375 2.374 0.804 3.697 1.691 2.006 149,600 24,200 13.71
US240 3.000 1.875 1.875 0.500 2.850 0.956 4.713 2.157 2.555 220,000 33,880 21.23
Notes:
1. RS Standard sprockets can be used if the sprocket teeth have been hardened and if the sprocket is not a cast iron type.
2. Chain should be lubricated using either the drip, oil bath or lubrication pump methods.
3. Offset links are not available.
4. riveted type chain will be supplied unless otherwise specified.
5. Chain must be used under 165 feet/min.
6. Multi-strand chain is not available.

Drive Chain A62 Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected]