JSS-2250/2500

2250N/2500N
MF/HF RADIO EQUIPMENT

INSTALLATION
MANUAL

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : [email protected]
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : [email protected]
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : [email protected]
CODE No.7ZPJD0537 01ETM ISO 9001, ISO 14001 Certified
SEP. 2012 Edition 1 JRC Printed in Japan
.
 CAUTIONS AGAINST HIGH VOLTAGE
Radio and radar devices are operated by high voltages of anywhere from a few hundred volts up to
many hundreds of thousands of volts. Although there is no danger with normal use, it is very
dangerous if contact is made with the internal parts of these devices. (Only specialists should attempt
any maintenance, checking or adjusting.)
There is a very high risk of death by even a few thousand volts, in some cases you can be fatally
electrocuted by just a few hundred volts. To prevent accidents, you should avoid contact with the
internal parts of these devices at all costs. If contact is inevitable as in the case of an emergency, you
must switch off the devices and ground a terminal in order to discharge the capacitors. After making
certain that all the electricity is discharged, only then can you insert your hand into the device.
Wearing cotton gloves and putting your left hand in your pocket, in order not to use both hands
simultaneously, are also very good methods of shock prevention.
Quite often, an injury occurs by secondary factors, therefore it is necessary to choose a sturdy and
level working surface. If someone is electrocuted it is necessary to thoroughly disinfect the affected
area and seek medical attention as soon as possible.

Cautions concerning treatment of

electrocution victims
When you find an electrocution victim, you must first switch off the machinery and ground all circuits. If
you are unable to cut off the machinery, move the victim away from it using a non-conductive material
such as dry boards or clothing.
When someone is electrocuted, and the electrical current reaches the breathing synapses of the
central nervous system inside the brain, breathing stops. If the victim's condition is stable, he or she
can be administered artificial respiration. An electrocution victim becomes very pale, and their pulse
can be very weak or even stop, consequently losing consciousness and becoming stiff.
Administration of first aid is critical in this situation.
 First aid

☆Note points for first aid

Unless there is impending danger leave the victim where he or she is, then begin artificial respiration.
Once you begin artificial respiration, you must continue without losing rhythm.

(1) Make contact with the victim cautiously, there is a risk that you may get electrocuted.

(2) Switch off the machinery and then move the victim away slowly if you must.

(3) Inform someone immediately (a hospital or doctor, dial emergency numbers, etc.).

(4) Lay the victim on his or her back and loosen any constrictive clothing (a tie, or belt).

(5) (a) Check the victim's pulse.

(b) Check for a heartbeat by pressing your ear against the victim's chest.
(c) Check if the victim is breathing by putting the back of your hand or face near the victim's
face.
(d) Check the pupils of the eyes.

(6) Open the victim's mouth and remove any artificial teeth, cigarette or chewing gum. Leave the
mouth opened and flatten the tongue with a towel or by putting something into the mouth to
prevent the victim's tongue from obstructing the throat. (If he or she is clenching the teeth and it is
difficult to open the mouth, use a spoon or the like to pry open the mouth.)

(7) Continually wipe the mouth to prevent the accumulation of saliva.

 ☆If the victim has a pulse but is not breathing
(“Mouth to mouth” resuscitation) Figure 1

(1) Place the victim’s head facing backward (place something under the neck like a pillow).
(2) Point the chin upward to widen the trachea.
(3) Pinch the victim’s nose, take a deep breath, then put your mouth over the victim’s mouth and exhale
completely, making sure that your mouth completely covers the victim’s mouth. Then remove your
mouth. Repeat this routine 10 to 15 times per minute (holding the nostrils).
(4) Pay attention to the victim to notice if he or she starts to breath. If breathing returns, stop
resuscitation.
(5) If it is impossible to open the victim’s mouth, put something like a plastic straw or vinyl tube into one
of the nostrils then blow air in while covering the mouth and the other nostril.
(6) Occasionally, when the victim comes back to consciousness, they immediately try to stand up.
Prevent this and keep them in a laying position. Give them something warm to drink and be sure
that they rest (do not give them any alcohol).

Administering artificial respiration by raising the head.

① (1) Raise the back of head, then place one

hand on the forehead and place the other
hand under the neck. → ①
Most victims open their mouth when this is
done, making “mouth to mouth”
resuscitation easier.

② (2) Cover the victim’s mouth by opening your

mouth widely, then push your cheek
against the victim’s nose, → ②
or pinch the victim’s nose to prevent air
from leaking out of it. → ③

(3) Completely exhale into the lungs.

Exhale into the lungs until the chest
inflates.
You have to blow as rapidly as possible for
the first 10 times.

“Mouse to mouse” artificial respiration

Figure 1
 ☆If the victim has no pulse and is not breathing
(Heart massage in combination with artificial respiration.) Figure 2

If the victim has no pulse, his or her pupils are dilated, and if you cannot detect a heartbeat, the heart may
have stopped, beginning artificial respiration is critical.

(1) Put both hands on the diaphragm, with hands on top of each other keeping both arms straight (If your
elbows are bent, you cannot push with as much power). Press the diaphragm with your body weight
until the chest sinks about 2 cm (about 50 times per minute).
(2) If administering first aid when alone:
Perform the heart massage about 15 times then blow in twice. Repeat this routine.
If administering first aid with two people:
One person performs the heart massage 5 times, and the other person blows air in once. Repeat
this routine (Heart massage and “mouth to mouth” resuscitation used together).
(3) Constantly check the pupils and the pulse, if the pupils become normal and the pulse steadies, keep
them in a laying position and give them something warm to drink, be sure that they rest (do not give
them any alcohol). In any case you have to entrust major decision making to a doctor. Having
understanding people around is essential to the victim’s recovery from the mental shock of
electrocution.

① ②

③ ④

Heart massage in combination with artificial respiration Figure 2

 Before Operation
Concerning the symbols
This manual uses the following symbols to explain correct operation and to
prevent injury or damage to property.
The symbols and descriptions are as follows. Understand them before
proceeding with this manual.

WARNING Indicates a warning that, if ignored, may

result in serious injury or even death.

CAUTION Indicates a caution that, if ignored, may

result in injury or damage to property.

Examples of symbols

The Δ symbol indicates caution (including DANGER and

WARNING). The illustration inside the Δ symbol specifies the
content of the caution more accurately. (This example warns of
possible electrical shock.)

The ; symbol indicates that performing an action is prohibited.

The illustration inside the ; symbol specifies the contents of the
prohibited operation. (in this example disassembly is prohibited.)

The z symbol indicates operations that must be performed. The

illustration inside the z symbol specifies obligatory instructions.
(In this example unplugging is the obligatory instruction.)

Concerning the WARNING labels

The WARNING labels are put on the NTD-2250/2500 Transceiver, NBD-2250/2500
Power supply, NFC-2250/2500 Antenna tuner, and NBB-714/724 Battery charger.
Do not take off, destroy, or modify the labels.

NTD-2250/2500 Transceiver (Upper view)

v
 NBD-2250/2500 Power supply (Upper view)

NFC-2250/2500 Antenna tuner

NBB-714/724 Battery charger

vi
 Handling Precautions

CAUTION
Do not distribute this INSTALLATION MANUAL to ordinary users, because
it has been created and published only for use by our service engineers.

Do not use this equipment for anything other than specified.

Doing so may cause failure or malfunction.

Do not turn the trimmer resistors or the trimmer capacitors on the PCB
unit, except when and if they need to be adjusted. Doing so may cause
failure or malfunction. They are preset at the factory.

Do not install this equipment in a place near water or in one with

excessive humidity, steam, dust or soot. Doing so may cause fire, electric
shock, or malfunction.

Do not test the distress call as doing so will inconvenience local shipping
and Rescue Centers.

Use an artificial antenna (antenna dummy load) in the case of the test of
equipment, or adjustment.
When using an antenna unavoidably, shorten transmitting time,

When repairing a RoHS compatible unit, use RoHS compatible parts and
lead-free solder, and also RoHS compatible wiring materials.

If a false distress alert is transmitted accidentally, follow the instructions below:

1. Press the CANCEL key on the controller (when appropriate, follow
the commands on screen) and terminate the transmission of the
distress call.
2. Report the false distress call to a nearby RCC (Rescue Coordination
Center).
(In Japan, inform the nearest Japan Coast Guard.)
Information to be reported:
The date/time, location, and reason why the false distress call was
transmitted. Also report the ship's name, type, nationality, and ID
number as well as the unit model name and manufacture number/date,
if possible.
3. Report the false distress call to nearby ships using 2182.0 kHz or
another frequency for distress and safety purposes on the
radiotelephone.
4. If any acknowledgements to the distress call are received, inform the
ships of the false distress call.

Do not short the lines of the mini plug. Doing so may cause malfunction.

vii
 CAUTION
Locate the antenna tuner, TX antenna and lead-in wire in locations as
far as possible from people and surrounding structures to satisfy the
following conditions.
• Far at least 30cm beyond anyone’s reach.
• Low vibration.
• Good ventilation and drainage.
• Protected from water (for above deck installation).
• Not exposed to smoke or corrosive gasses from the smokestack.
• Not exposed to heat.
• Protected from icing.

In the field maintenance mode, all DSC functions including distress alert
cannot be used. So when setup is complete, always restart by powering
off and on using breakers, or place the system in sleep mode.
If the equipment is left without operating in this mode, the maintenance
mode off timer automatically put the system into sleep mode.

Use F2.3.3 Calibration menu only when having errors obviously.

The batteries, except for sealed lead-acid batteries that require no

equalization, should be carried out the equalizing charge at least every
six months

When connecting the battery to the rack/console, first connect the cable
to the radio rack/console before connecting to the battery.

When connecting the AC mains, first turn off the power at the switchboard
before wiring the cables to the equipment.

viii
 Contents

Before Operation ........................................................................... v

Handling Precautions .................................................................... vii

1. CONFIGURATION AND SPECIFICATIONS ................................... 1-1

1.1 Basic configuration ........................................................................... 1-1

1.1.1 DSC model (JSS-2250/2500) ...................................................... 1-1

1.1.1.1 Standard components ....................................................................... 1-1
1.1.1.2 Options ......................................................................................... 1-1

1.1.2 DSC/NBDP model (JSS-2250N/2500N) ....................................... 1-2

1.1.2.1 Standard components ....................................................................... 1-2
1.1.2.2 Options ......................................................................................... 1-2

1.1.3 System configuration .................................................................... 1-3

1.2 Block diagram .................................................................................... 1-4

1.2.1 DSC model (JSS-2250/2500) ...................................................... 1-4

1.2.2 DSC/NBDP model (JSS-2250N/2500N) ....................................... 1-5
1.3 Specifications ................................................................................... 1-6

1.3.1 JSS-2250/2500 MF/HF Radio Equipment ..................................... 1-6

1.3.2 Options ........................................................................................ 1-10
1.3.3 Peripheral interfaces .................................................................... 1-12
1.4 Interconnection diagram ................................................................... 1-16
1.5 Radio rack internal wiring diagram .................................................... 1-18

2. INSTALLATIONS .......................................................................... 2-1

2.1 Installation procedure ....................................................................... 2-1
2.2 External dimensions and equipment overview ..................................... 2-5

2.2.1 NCU-515A Radio Rack ................................................................ 2-5

2.2.1.1 External dimensions and installation space ...................................... 2-5
2.2.1.2 Installation ...................................................................................... 2-7
2.2.1.3 Connecting the power cable ............................................................ 2-10
2.2.1.4 Connecting the signal lines .............................................................. 2-13
2.2.1.5 Connecting the coaxial cables ......................................................... 2-14
2.2.1.6 Removal of the eyebolts ................................................................ 2-15
2.2.1.7 Terminal description ........................................................................ 2-16

2.2.2 NTD-2250/2500 Transceiver ....................................................... 2-19

2.2.2.1 External dimensions ........................................................................ 2-19
2.2.3 NBD-2250/2500 Power Supply .................................................... 2-20
2.2.3.1 External dimensions ......................................................................... 2-20

2.2.4 NBB-714 Battery Charger ........................................................... 2-21

2.2.4.1 External dimensions ......................................................................... 2-21
2.2.4.2 Connecting the signal lines .............................................................. 2-23
2.2.4.3 Setting the AC input voltage (110 VAC/220 VAC) .............................. 2-24
2.2.4.4 Setting the battery charging voltage ................................................. 2-26
2.2.4.5 Accessory terminals ......................................................................... 2-27
2.2.4.6 Other functions (protection circuit) .................................................... 2-27

2.2.5 NBB-724 Battery Charger ........................................................... 2-28

2.2.5.1 External dimensions ......................................................................... 2-28
2.2.5.2 Connecting the signal lines .............................................................. 2-29
2.2.5.3 Setting the AC input voltage (110 VAC/220 VAC) .............................. 2-30
2.2.5.4 Setting the battery charging voltage ................................................. 2-32
2.2.5.5 Prohibiting equalized charging ......................................................... 2-33
2.2.5.6 Details on switches and controls in the blank panel .......................... 2-34
2.2.5.7 Accessory terminals ......................................................................... 2-36
2.2.5.8 Other functions (protection circuit) .................................................... 2-36

2.2.6 NCM-2150 MF/HF Controller ....................................................... 2-38

2.2.6.1 External dimensions and installation space ....................................... 2-38
2.2.6.2 Installation ....................................................................................... 2-39
2.2.6.3 Supplementary materials .................................................................. 2-43

2.2.7 NQW-261 Handset ...................................................................... 2-45

2.2.7.1 External dimensions ......................................................................... 2-45
2.2.7.2 Building the connector for the handset .............................................. 2-46

2.2.8 NQD-2250 Connection Box ......................................................... 2-47

2.2.8.1 External dimensions ......................................................................... 2-47
2.2.8.2 Installation ....................................................................................... 2-48
2.2.8.3 Connecting the signal lines .............................................................. 2-49
2.2.8.4 Terminal description ......................................................................... 2-50

2.2.9 NDZ-227 Data Terminal ............................................................... 2-51

2.2.9.1 External dimensions and installation space ....................................... 2-51
2.2.9.2 Data terminal installation .................................................................. 2-52
2.2.9.3 Wiring the power cable and the signal cable ..................................... 2-55

2.2.10 NDF-369 Keyboard ..................................................................... 2-56

2.2.6.1 External dimensions and installation space ....................................... 2-56

2.2.11 NFC-2250/2500 Antenna Tuner ................................................... 2-57

2.2.11.1 External dimensions and installation space ....................................... 2-57
2.2.11.2 Antenna tuner installation ................................................................. 2-58
 2.2.11.3 Cable processing ............................................................................ 2-64
2.2.11.4 Wiring the control signal lines .......................................................... 2-65

2.2.12 NQD-2253 Junction Box .............................................................. 2-66

2.2.12.1 External dimensions ........................................................................ 2-66
2.2.12.2 Handling the attached rubber board ................................................. 2-67

2.2.13 NKG-91 Printer ........................................................................... 2-68

2.2.13.1 External dimensions and installation when attached to a wall ........... 2-68
2.2.13.2 External dimensions and installation for a flush mount ..................... 2-70
2.2.13.3 Connecting the signal lines .............................................................. 2-72

2.2.14 DPU-414 Printer (desktop type) .................................................. 2-73

2.2.14.1 External dimensions and installation space ...................................... 2-73
2.2.14.2 Connecting to the MF/HF controller ................................................. 2-74

2.2.15 NKG-800 Printer (Centronics compliant/desktop type) ................. 2-75

2.2.15.1 External dimensions and installation space ...................................... 2-75
2.2.15.2 Connecting to the MF/HF controller ................................................... 2-76
2.2.15.3 Setting the DIP switch ..................................................................... 2-77

3. APPENDIX ................................................................................... 3-1

3.1 Block diagram ...................................................................................... 3-1
3.1.1 NTD-2250 TRANSCEIVER ............................................................ 3-1
3.1.2 NTD-2500 TRANSCEIVER ............................................................ 3-2
3.1.3 CMN-2250 TRX UNIT ................................................................... 3-3
3.1.4 CMJ-2250 WKR MODEM UNIT ..................................................... 3-4
3.1.5 NBD-2250 POWER SUPPLY ......................................................... 3-5
3.1.6 NBD-2500 POWER SUPPLY ......................................................... 3-6
3.1.7 NCM-2150 MF/HF CONTROLLER ................................................. 3-7
3.1.8 NDZ-227 DATA TERMINAL ........................................................... 3-8
3.1.9 NFC-2250 ANTENNA TUNER ....................................................... 3-9
3.1.10 NFC-2500 ANTENNA TUNER ....................................................... 3-10
 CONFIGURATION AND SPECIFICATIONS

1. CONFIGURATION AND SPECIFICATIONS

1.1 Basic configuration
This section describes the basic configuration. However note that according to the composition, the
model variants are as follows.
- JSS-2250 :250W Radiotelephone/ DSC
- JSS-2250N :250W Radiotelephone/ DSC & NBDP
- JSS-2500 :500W Radiotelephone/ DSC
- JSS-2500N :500W Radiotelephone/ DSC & NBDP
In this document, unless otherwise specified, “JSS-2250/2500” may include “JSS-2250N/2500N”.

1.1.1 DSC model (JSS-2250/2500)

1.1.1.1 Standard components

No. Description Model Qty Notes
1 Transceiver NTD-2250/2500 1 For 250W and 500W respectively
2 Power supply NBD-2250/2500 1 For 250W and 500W respectively
3 MF/HF controller NCM-2150 1
3-1 Controller cable 7ZCJD0343 1 5m
3-2 Handset NQW-261 1 Includes the cradle
4 Antenna tuner NFC-2250/2500 1 For 250W and 500W respectively
5 Instruction manual 7ZPJD0535 1

1.1.1.2 Options
No. Description Model Notes
1 Battery charger NBB-724 22A
2 Battery charger NBB-714 10A *For maintenance-free sealed battery only
3 Joint box JQD-69C For both RX and WKR
4 Junction box NQD-2253
5 Coaxial connector M-P-7, M-A-JJ For RG-12/UY and RG-10/UY
6 MF/HF controller NCM-2150 One additional controller available.
6-1 Controller cable 7ZCJD0343 5m
6-2 Handset NQW-261 Waterproof type (IP66 equivalent)
6-3 Flush mounting bracket MPBC42957
6-4 Mounting bracket MPBX44354
6-5 Connection box NQD-2250 For extension and expansion of the controller
7 Printer NKG-800 Desktop type
7-1 Printer connection cable 6ZCSC00407
7-2 Printer power cable 6JNKD00100B
7-3 Printer paper 5ZPCM00006
7-4 Ink ribbon (SP-16051) 5ZZCM00003
8 Printer NKG-91 Wall mount or flush mount type
8-1 Printer connection cable 7ZCJD0254A
8-2 Printer paper 7ZPJD0384
8-3 Wall mounting bracket MPBP31446
9 Printer DPU-414 Desktop type
9-1 Printer connection cable 7ZCJD0254A
9-2 Printer power cable 7ZCJD0257C
9-3 Printer paper 6ZCAF00252A
10 Distress message controller NCH-321A

1-1
CONFIGURATION AND SPECIFICATIONS

1.1.2 DSC/NBDP model (JSS-2250N/2500N)

1.1.2.1 Standard components

No. Description Model Qty Notes
1 Transceiver NTD-2250/2500 1 For 250W and 500W respectively
2 Power supply NBD-2250/2500 1 For 250W and 500W respectively
3 MF/HF controller NCM-2150 1
3-1 Controller cable 7ZCJD0343 1 5m
3-2 Handset NQW-261 1 Includes the cradle
4 Antenna tuner NFC-2250/2500 1 For 250W and 500W respectively
5 Data terminal NDZ-227 1
5-1 DTE cable 7ZCJD0388 1
5-2 DTE power cable 7ZCJD0419 1
5-3 Keyboard NDF-369 1 NBDP option
6 Printer NKG-800 1
6-1 Printer connection cable 7ZCSC0205A 1
6-2 Printer power cable 6JNKD00100B 1
7 Instruction manual 7ZPJD0535 1

1.1.2.2 Options
No. Description Model Notes
1 Battery charger NBB-724 22A
2 Battery charger NBB-714 10A *For maintenance-free sealed battery only
3 Joint box JQD-69C For both RX and WKR
4 Junction box NQD-2253
5 Coaxial connector M-P-7, M-A-JJ For RG-12/UY and RG-10/UY
6 MF/HF controller NCM-2150 One additional controller available.
6-1 Controller cable 7ZCJD0343 5m
6-2 Handset NQW-261 Waterproof type (IP66 equivalent)
6-3 Flush mounting bracket MPBC42957
6-4 Mounting bracket MPBX44354
6-5 Connection box NQD-2250 For extension and expansion of the controller
7 Data terminal NDZ-227
7-1 DTE cable 7ZCJD0388
For expansion of the controller
7-2 DTE power cable 7ZCJD0419
7-3 Keyboard NDF-369
7-4 Mounting bracket MPBP31721
7-5 USB memory UDG4-1GAR-JRC Hagiwara Sys-Com / 1GB
8 Printer NKG-800
8-1 Printer connection cable 7ZCSC0205A
8-2 Printer power cable 6JNKD00100B Desktop type
8-3 Printer paper 5ZPCM00006
8-4 Ink ribbon (SP-16051) 5ZZCM00003
9 Printer NKG-91
9-1 Printer connection cable 7ZCJD0254A Wall mount or
9-2 Printer paper 7ZPJD0384 flush mount type
9-3 Wall mounting bracket MPBP31446
10 Printer DPU-414
10-1 Printer connection cable 7ZCJD0254A
Desktop type
10-2 Printer power cable 7ZCJD0257C
10-3 Printer paper 6ZCAF00252A
11 Distress message controller NCH-321A

1-2
 CONFIGURATION AND SPECIFICATIONS

1.1.3 System configuration

NKG-800 Printer
NDZ-227 Data terminal
NDF-369 Keyboard
NCM-2150 MF/HF Controller (DSC/NBDP model only)
NQW-261 Handset

Expansion Controller

NTD-2250/2500 Transceiver GPS

NBD-2250/2500 Power supply

NFC-2250/2500
Antenna Tuner
NCH-321A DMC

NBB-724 Battery charger

* The equipment can also be

connected to the VDR
server to use the remote
maintenance system.

1-3
CONFIGURATION AND SPECIFICATIONS

1.2 Block diagram

1.2.1 DSC model (JSS-2250/2500)

Rx/WKR
Tx antenna
antenna

JQD-69C
Joint box

Lead wire
RG-12/UY
TH-19/1.2

NQW-261 M-P-7
Handset M-P-7/M-P-5
7ZCJD M-A-JJ
RX/WKR ANT TX ANT
0343 TTYCS- 4 M-P-7
7ZCJD
（5m） DPYC-2.5 RG-10/UY
NCM-2150 TX
0426
MF/HF Controller NTD-2250/2500 ANT
NFC-2250/2500
Transceiver Antenna tuner
TTYCYS-4
NQD-2250
NQD-2253
Connection Junction
box NBD-2250/2500
box
Power supply
6.5V DC 7ZCJD0254A
DPYC-16 100V/220V AC
NBB-724 50/60Hz 1φ
NKG-91 Battery charger DPYC-25 24V DC
Printer 200Ah

TTYCS- 4
DPYC-2.5

NQD-2250
Connection
box

TTYCS- 1
GPS

Expansion controller
MPYCS- 7
NCH-321A
DMC

TTYCS- 1
RMS
(VDR)

TTYCS- 4
AME

1-4
 CONFIGURATION AND SPECIFICATIONS

1.2.2 DSC/NBDP model (JSS-2250N/2500N)

Rx/WKR
Tx antenna
antenna

JQD-69C
Joint box

Lead wire
RG-12/UY
TH-19/1.2

NQW-261 M-P-7
Handset M-P-7/M-P-5
7ZCJD M-A-JJ
RX/WKR ANT TX ANT
0343 TTYCS- 4 M-P-7
7ZCJD
（5m） DPYC-2.5 RG-10/UY
NCM-2150 TX
0426
MF/HF Controller NTD-2250/2500 ANT
NFC-2250/2500
Transceiver Antenna tuner
TTYCYS-4
NQD-2250
NQD-2253
Connection Junction
box NBD-2250/2500
box
Power supply
7ZCJD0419 7ZCJD0388
DPYC-16 100V/220V AC
NBB-724 50/60Hz 1φ
Battery charger DPYC-25 24V DC
NDZ-227 200Ah
Data terminal

NDF-369
Keyboard

7ZCSC0205A 6JNKD00100B

TTYCS- 4
NKG-800 DPYC-2.5
Printer

NQD-2250
Connection
box

TTYCS- 1
GPS

Expansion controller
MPYCS- 7
NCH-321A
DMC

TTYCS- 1
RMS
(VDR)

TTYCS- 4
AME

1-5
CONFIGURATION AND SPECIFICATIONS

1.3 Specifications
1.3.1 JSS-2250/2500 MF/HF Radio Equipment

z General Specifications
Transmission frequency 1605.0 - 27500.0 kHz (100 Hz steps)
Reception frequency 90.0 - 29999.9 kHz (100 Hz steps)
Frequency stability Within ±10 Hz
Type of emission TEL mode : J3E
DSC/TLX mode : F1B
CW mode : A1A
AM mode : H3E
H2B mode : H2B
DATA mode : J2D
Channels User channels (TEL/DSC/CW) : Max. 400 ch (20 ch x 20 grp)
User channels (TLX) : Max. 400 ch (20 ch x 20 sta)
ITU preset channels : 1722 ch
Scan channels Max. 20 channels (group specification method)
Nominal frequency J3E/ A1A/ H3E/ H2B/ J2D : Carrier frequencies
F1B : Assigned frequency
Communication method in TEL Push-to-talk (simplex, semi-duplex)
Antenna impedance 50Ω unbalanced
Channel switching duration 15 sec or less
Interface IEC61162-1 (GPS/AME/RMS)
Compass safety distance 1.9 m
Main controls DSC call (sending and receiving), communication frequency/
channel settings, Tx power settings, RF gain adjustment, volume
adjustment, LCD adjustment
Performance criteria IMO A.806(19), A.694(17), MSC68(68), MSC/Circ.862
IEC 60945 Ed.4 2002-08
Power supply voltage 90 VAC to 132 VAC, 180 VAC to 264 VAC
24 VDC (21.6 VDC to 31.2 VDC)
Current consumption Transmission AC : 2kVA / 3kVA
(JSS-2250/ 2500) 24VDC : 40A / 40A
Reception AC : 0.5kVA / 0.5kVA
24VDC : 6A / 6A
Operating temperature range -15°C - +55°C(parts exposed to condensation -25°C - +55°C)
Storage temperature range -15°C - +55°C(parts exposed to condensation -25°C - +70°C)
Humidity resistance No abnormality after standing 4 hours in +40°C, 93%RH
Vibration resistance (3 axes) 2 Hz - 5 Hz to 13.2 Hz : Full amplitude ±1 mm±10%
2
13.2 Hz to 100 Hz : Max acceleration 7 m/s fixed
No abnormality after testing resonance points or at 30 Hz for 2 hours
Category type of Antenna tuner and the junction box : Exposed
the weather resistance Other units : Protected
Continuous operation (TEL) No abnormality after operating continuously for 8 hours
Continuous operation (DSC,WKR) No abnormality after operating continuously for 24 hours
Protection rating IP22 equivalent (controller panel)
Dimensions and mass (approx) Main unit (Incase of the NCU-515A Rack)
(JSS-2250/ 2500) 520mm(W) x 665mm(H) x 450mm(D) [ex. projections], 90kg/96kg
Antenna tuner
395mm(W) x 622mm(H) x 198mm(D) [ex. projections], 10kg/10kg
MF/HF controller
230mm(W) x 142mm(H) x 89mm(D) [ex. projections], 1.3kg
Data terminal
336mm(W) x 244mm(H) x 88mm(D) [ex. projections], 4.6kg

1-6
 CONFIGURATION AND SPECIFICATIONS

z Transmitter
Antenna output power 1605.0 AC ： 200Wpep / 400Wpep
(JSS-2250/ 2500) - 3999.9 kHz 24VDC ： 100Wpep / 100Wpep
4000.0 AC ： 250Wpep / 500Wpep
- 27500.0 kHz 24VDC ： 150Wpep / 150Wpep
Modulation method Low-power stage balanced modulation
Occupied bandwidth J3E/ J2D/ H2B : Within 3 kHz
F1B/ A1A : Within 0.5 kHz
Carrier suppression (J3E) 40 dB or more
Unwanted emissions in the Mean power of 50 mW or lower, or 43 dB or more lower than the
out-of-band domain mean power of the basic frequency
Unwanted emissions in the spurious At J3E:
domain 1.5 to 4.5 kHz : 31 dB or more
4.5 to 7.5 kHz : 38 dB or more
7.5 kHz and upwards : 43 dB or more
(Peak power of unwanted emissions is 50 mW or less.)

At F1B:

Attenuation [dB]

Mistuned frequency [Hz]

Overall distortion and noise -20 dB or less

AF frequency response Deviation is within 6 dB in 350 Hz to 2700 Hz range.
Tone frequency 1500 Hz or 1400 Hz

z Receiver
Receiving system Double superheterodyne
1st IF 70.036 MHz
2nd IF 36 kHz
Reception frequency stability Within ±10 Hz
Sensitivity (SINAD 20dB) J3E : 2.5 uV or less (1605.0 to 27500.0 kHz)
F1B : 0.7 uV or less (1605.0 to 27500.0 kHz)
A1A : 1.4 uV or less (1605.0 to 27500.0 kHz)
Pass band/Adjacent signal J3E : 2.4 - 3.0 kHz (6 dB bandwidth) within
selectivity ±2.1 kHz (66 dB bandwidth)
F1B : 270 - 300Hz (6 dB bandwidth) within
±550 Hz (60 dB bandwidth)
Spurious response J3E : 60 dB or more
F1B : Symbol error rate of 1% or better at a wanted signal level
of 10 uV and an unwanted signal level of 31.6 mV
separated by 750 Hz

1-7
CONFIGURATION AND SPECIFICATIONS

Blocking/Desensitization J3E : When an unwanted signal level separated by 3 kHz is

added to the wanted signal level of 10 uV, the unwanted
signal input voltage suppressing output of the wanted
signal by 3 dB is 10 mV or more.
F1B : Symbol error rate of 1% or better at a wanted signal level
of 10 uV and an unwanted signal level of 1 mV
separated by 500 Hz
Overall distortion and noise When an input signal level of 30 uV is applied, the ratio between
low-frequency output 1000 Hz and unwanted components contained
in that output is 30 dB or more.
Conducted spurious emission Power emitted from antenna terminal is 2 nW or less (9kHz - 2GHz)
and 20 nW or less (2GHz - 4GHz).
Clarifier variable range ±200 Hz (1 Hz steps)
Antenna impedance 50Ω unbalanced
Line output 0 dBm 600Ω (balanced)

z DSC Watchkeeping Receiver.

Reception frequency Distress and safety frequencies of 2187.5 kHz and 8414.5 kHz, and
additionally on one or more of the 4207.5 kHz/ 6312.0 kHz/ 12577.0
kHz/ 16804.5 kHz
Receiving system Double superheterodyne
1st IF 40.04025 MHz
2nd IF 40.25 kHz
Frequency stability Within ±10 Hz
Sensitivity 1% or lower symbol error rate at reception input voltage of 1µV
Passband 6 dB bandwidth : 270 - 300 Hz
30 dB bandwidth : Within ±380 Hz
60 dB bandwidth : Within ±550 Hz
Spurious response Symbol error rate of 1% or better when an unwanted signal level of
31.6 mV is applied to a wanted signal level of 10 uv from an
intermediate frequency separated by 750 Hz or more through to a
frequency 3x the test frequency
Blocking/Desensitization Symbol error rate of 1% or better at a wanted signal level of 10 uV
and an unwanted signal level of 1 mV separated by 500 Hz
Conducted spurious emission Power emitted from antenna terminal is 2 nW or less.
Antenna impedance 50Ω unbalanced

z DSC Modem
Modulation rate Within 100 baud ±30ｘ10-6
Modulation method FSK (sub-carrier: 1700 Hz)
Mark frequency (Y) Transmission : Within 1615 Hz ±0.5 Hz
Reception (permissible value) : Within 1615 Hz ±20 Hz
Space frequency (B) Transmission : Within 1785 Hz ±0.5 Hz
Reception (permissible value) : Within 1785 Hz ±20 Hz
DSC protocol ITU-R recommendation M.493-11 (Class A and B)
DSC operation standards ITU-R recommendation M.541-9, M.821-1
DSC code 10-bit error detecting code

z NBDP Modem
Modulation rate Within 100baud ±30ｘ10-6
Modulation method FSK （sub-carrier：1700Hz）
Mark frequency (Y) Transmission : Within 1615 Hz ±0.5 Hz
Reception (permissible value) : Within 1615 Hz ±20 Hz
Space frequency (B) Transmission : Within 1785 Hz ±0.5 Hz
Reception (permissible value) : Within 1785 Hz ±20 Hz
NBDP Protocol ITU-R recommendation M.476-5,M.491-1,M.492-6,M.625-4
ITU-T recommendation F.1、F.130、S.6
NBDP code 7-bit error detecting code

1-8
 CONFIGURATION AND SPECIFICATIONS

z Antenna Tuner
Frequency range 1605.0 - 27500.0 kHz
Maximum input power 1605.0 - 3999.9 kHz 250Wpep / 500Wpep
(JSS-2250/ 2500) 4000.0 - 27500.0 kHz 300Wpep / 700Wpep
SWR after tuning 2:1 or less
Tuning method Preset or auto-tuning
Tuning time Preset tuning: 0.5 seconds, auto-tuning: max. 45 seconds
Power supply 24 VDC (21.6 VDC to 24.7 VDC)

z MF/HF controller
Communication speed 57.6 kbps
Communication interface RS-485 and RS-232C, and Centronics compliant
Microphone input impedance 150Ω balanced
Standard modulation input -54 dBm
Audio output Internal loud speaker (8Ω) : 5W max
External speaker impedance : 8Ω or more
Handset phone (150Ω) : Rated 1mW or more
LCD display 3.8 inch FSTN monochrome, 320 x 240 dot, LED backlight

● Data terminal
Communication speed 4.8kbps
Communication interface RS-232C
USB interface USB 2.0, FAT16/32 file format
Keyboard interface PS/2
Printer interface Centronics compliant
LCD display 10.4 inch TFT color, 640x480 dots, CCFL backlight
Standard brightness 450cd/m2, Viewing angle 160 ﾟ/140 ﾟ Contrast
600：1

● Keyboard
Communication interface Serial two wire interactive transmission
Connector Mini DIN 5Pin
Durability 20,000,000 times

● Printer (NKG-800)
Printing system Serial impact dot matrix
Communication interface Centronics compliant
Supported fonts ANK FX850 mode : 324 characters
IBM Proprinter II mode : 264 characters
Paper feed system Roll paper holder
Paper type 209 - 216 mm (8.23 - 8.50") roll paper
Buffer size ANK FX850 mode : 21 kbytes
IBM Proprinter II mode : 9.3 kbytes
Density adjustment Manual (nonstepped)
Power supply voltage 10.2 VDC - 31.2 VDC
Power consumption Maximum 35 W

1-9
CONFIGURATION AND SPECIFICATIONS

1.3.2 Options

(1) Battery Charger (NBB-714)

Source voltage 90 VAC to 132 VAC or 180 VAC to 264 VAC (50/60 Hz)
Current consumption Charging : 8 A or less (100 VAC input)
4 A or less (220 VAC input)
Discharging : 0.3 A or less (at 24 VDC ope)
Charging current Maximum 10 A
Charging circuit/ characteristic Floating charge
16 VDC or more: Constant voltage or current characteristic
Less than 16 VDC: Reduced current characteristic*
(*) Foldback current limiting characteristic
Functions Overvoltage input protection, Reverse polarity protection,
Dimmer lamp, Alarm mute with remote control
Alarm type Batt low/high voltage, Internal temperature, AC fail,
Other abnormal charging
Temperature range for full performance -15°C - +55°C
Operating temperature range -15°C - +55°C
Storage temperature range -25°C - +65°C
Humidity resistance No abnormality after standing 4 hours in +40°C, 93% RH
Vibration resistance (3 axes) 2 Hz - 5 Hz to 13.2 Hz: : Full amplitude ±1 mm±10%
2
13.2 Hz to 100 Hz: : Maximum acceleration 7 m/s fixed
No abnormality after testing resonance points or at 30 Hz for more
than 2 hours

(2) Battery Charger (NBB-724)

Source voltage 90 VAC to 132 VAC or 180 VAC to 264 VAC (50/60 Hz)
Current consumption Charging : 15 A or less (100 VAC input)
8 A or less (220 VAC input)
Discharging : 0.5 A or less (at 24 VDC ope)
Charging current Maximum 22 A (Common to Floating & Equalizing charge)
Charging circuit/ characteristic Floating charge and equalizing charge
18 VDC or more: Constant voltage or current characteristic
Less than 18 VDC: Reduced current characteristic*
(*) Foldback current limiting characteristic
Functions Overvoltage input protection, Reverse polarity protection,
Dimmer lamp, Float/Equal changing, DC ope, Batt temp
Alarm type Batt low/high voltage, Internal temperature, Other abnormal charging

Temperature range for full performance -15°C - +55°C

Operating temperature range -15°C - +55°C
Storage temperature range -25°C - +65°C
Humidity resistance No abnormality after standing 4 hours in +40°C, 93% RH
Vibration resistance (3 axes) 2 Hz - 5 Hz to 13.2 Hz: : Full amplitude ±1 mm±10%
2
13.2 Hz to 100 Hz: : Maximum acceleration 7 m/s fixed
No abnormality after testing resonance points or at 30 Hz for more
than 2 hours

1-10
 CONFIGURATION AND SPECIFICATIONS

(3) Printer (NKG-91)

Printing system Thermal line dot
Communication interface RS-232C, 4.8/9.6/38.4 kbps
Data control RTS/CTS
Data buffer 4096 byte
Maximum print speed 20 mm/sec or more
Roll paper width 58 mm
Power supply voltage 6.5 VDC (5 VDC to 8.7 VDC)
Current consumption Maximum 2 A

(4) Printer (DPU-414)

Printing system Thermal serial dot
Communication interface RS-232C, 4.8k/9.6k/38.4kbps
Data control HW busy
Data buffer About 28kbyte
Maximum print speed 52.5cps
Roll paper width 112mm
Power voltage 6.5VDC
Current consumption Maximum 2A

1-11
CONFIGURATION AND SPECIFICATIONS

1.3.3 Peripheral interfaces

(1) GPS or other navigation aid interface

Interface standard NMEA0183/IEC61162-1 compliant
Protocol 4800 bps, start 1 bit, data 8 bit, stop 1 bit
Non parity
Input sentence NMEA0183 V1.5 : GGA/GLL/RMC
V2.0 : GGA/GLL/RMC/ZDA
V2.3 : GGA/GLL/RMC/GNS/ZDA
（Talker = "GP" or other）
Data type Ship position & time information : GGA/GNS/GLL/RMC
Date information : ZDA/RMC
Equipment time information : ZDA/GGA/GNS/GLL/RMC

(1.1) Electrical description

CQD-2417 CMC-2425/2450 CMN-2250 CMJ-2250

TERMINAL PA CONTROL TRX UNIT WKR MODEM UNIT
BOARD UNIT +3.3V
TR501 R541 R540
TB204 3.3k
J202 J102 J172 J1111 J1131 J502 R542

GPS_RX-A 26 1
W30 W13 W14
27 2 TR502 R543
GPS_RX-B
R544 CD503
PHT501
R541, R543: 270
R542, R544: 10k

■ Load requirements

Current consumption ：2mA at 2V or less

Maximum input voltage ：±15V or more

Recommended operating current ：2mA or more

1-12
 CONFIGURATION AND SPECIFICATIONS

(1.2) List of sentences and associated data fields

(1.2.1) GGA – Global positioning system (GPS) fix data

$--GGA, hhmmss, llll.ll, a, yyyyy.yy, a, x, xx, x.x, x.x, M, x.x, M, x.x, xxxx *hh<CR><LF>

Differential reference

station ID, 0000-1023

Age of differential GPS data

Units of geoidal separation, m

Geoidal separation

Units of antenna altitude, m

Antenna altitude above/below mean sea level

(geoid)

Horizontal dilution of precision

Number of satellites in use, 00-12, may be different

from the number in view

GPS quality indicator

Longitude E/W

Latitude N/S

UTC of position

(1.2.2) GLL – Geographic position – Latitude/longitude

$--GLL, llll.ll, a, yyyyy.yy, a, hhmmss.ss, A, a *hh<CR><LF>

Mode indicator:

A = Autonomous, D = Differential, E = Estimated

M = Manual input, S = Simulator, N = Data not valid

Status: A= data valid, V= data invalid

UTC of position

Longitude, E/W

Latitude, N/S

1-13
CONFIGURATION AND SPECIFICATIONS

(1.2.3) RMC – Recommended minimum specific GNSS data

$--RMC, hhmmss.ss, A, llll.ll, a, yyyyy.yy, a, x.x, x.x, xxxxxx, x.x, a, a *hh<CR><LF>

Mode indicator:
A = Autonomous, D = Differential,
E = Estimated, M = Manual input,
S = Simulator, N = Data not valid
Magnetic variation, degrees, E/W
Date: dd/mm/yy
Course over ground, degrees true
Speed over ground, knots
Longitude, E/W
Latitude, N/S
Status: A = data valid, V = navigation receiver warning
UTC of position fix

(1.2.4) GNS – GNSS fix data

$--GNS, hhmmss.ss, llll.ll, a, yyyyy.yy, a, c---c, xx, x.x, x.x, x.x, x.x, x.x *hh<CR><LF>

Differential reference station ID

Age of differential data
Geoidal separation, m
Antenna altitude, m, re:mean-sea-level (geoid)
HDOP
Total number of satellites in use, 00-99
Mode indicator:
N = No fix, A = Autonomous, D = Differential,
P = Precise, R = Real Time Kinematic, F = Float RTK,
E = Estimated, M = Manual input, S = Simulator
Longitude, E/W
Latitude, N/S
UTC of position

(1.2.5) ZDA – Time and date

$--ZDA, hhmmss.ss, xx, xx, xxxx, xx, xx *hh<CR><LF>

Local zone minutes, 00 to +59

Local zone hours, 00 h to ±13 h

Year (UTC)

Month, 01 to 12 (UTC)

Day, 01 to 31 (UTC)

UTC

1-14
 CONFIGURATION AND SPECIFICATIONS

(2) RMS interface

Interface standard IEC61162-1 compliant
Protocol 4800 bps, start 1 bit, data 8 bit, stop 1 bit
Non parity
Output message IEC61162-1 compliant proprietary sentence
$PJRCL sentence (for RMS log saving)
$PJRCM sentence
(Device ID = "CT")
Data type Model number, serial number, self-diagnosis information, etc.

(3) Accessory interface

DC_OPE Input circuit : Current loop (Photo coupler)
Input current(between a and b) : 4.4mA (DC24V)
+BK Output voltage (normal) : DC24V
Maximum output : 0.5A
-BK ・Input
Input current : 2mA
・Output
Maximum output current : 0.5A
RBK Maximum output current : 1.5A
EXT_KEY Input current : 2mA
SEL_BK Input current : 2mA
RBK（NCM-2150/ EXT MODEM） Maximum output current : 0.3A

1-15
CONFIGURATION AND SPECIFICATIONS

1.4 Interconnection diagram

TX ANT RX ANT WKR/RX ANT

Self supporting
ANTENNA 6m WHIP 6m WHIP
NAW-208S ANTENNA ANTENNA
NAW-60 NAW-60
NFC-2250/2500 GND
ANTENNA TUNER JQD-69C JQD-69C
NCU-515A MF/HF RADIO RACK
JOINT BOX JOINT BOX
ANT_CURR
PA_MUTE
ATU_RXD

ATU_TXD
ATU_24V

GND (OPTION) GND

(OPTION)
GND

GND
RBK

*RG-12/UY
NTD-2250/2500 TRANSCEIVER
RF_GND

TB1 TB2 WKR/RX ANT

RF_IN

1 8

NBD-2250/2500 POWER SUPPLY

WHT

GRN
GRY
RED

BRN
PNK
YEL

BLK

*RG-12/UY
TB4 TB3 RX ANT
GND (OPTION) NBB-724 BATTERY CHARGER
*RG-10/UY
TX ANT
M-P-5 M-P-7 CQD-2417 TERMINAL BOARD
L=1.3m L=0.3m CONTROLLER ACCESSORY-1 GPS ACCESSORY-2 TUNER
Attachment to NFC-2250/2500
7ZCJD0426

15 LINE_OUT+

42 ANT_CURR
4 DISP_LINE+

16 LINE_OUT-
10 DISP_PWR
11 DISP_PWR
5 DISP_LINE-

26 GPS_RX-A
27 GPS_RX-B

38 PA_MUTE
29 DC_OPE+

31 R_CONT+

39 ATU_RXD
6 DISP_KEY

37 ATU_RBK

43 ATU_TXD
20 EXT_KEY

30 DC_OPE-

32 R_CONT-
17 LINE_IN+

41 ATU_24V
7 SYS_RST

18 LINE_IN-
8 RS-485-A
9 RS-485-B

21 SEL_BK
19 GND

22 GND

25 GND

28 GND

33 GND

36 GND

40 GND

44 GND
45 GND
12 GND
13 GND
14 GND

35 RBK
1 GND

23 +BK

34 +BK
24 -BK
2 NC
3 NC
WHT

GRN
GRY
RED

BRN
PNK
YEL

BLK

TB201 TB202 TB203 TB204 TB205

1

10 12
37 38 39 40 41 42 43 44 45 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

NQD-2253 JUNCTION BOX

(OPTION)
*4 X 2 X 0.75mm2 (JIS TTYCYS-4)

ABOVE DECK
*1 X 2 X 0.75mm2
(JIS TTYCS-1) ANTENNA
MULTI
*4 X 2 X 0.75mm2 (JIS TTYCS-4) *1 X 2 X 0.75mm2 COUPLER
(JIS TTYCS-1)
INM-C_PS
*1X 2 X 2.5mm2 (JIS DPYC-2.5)
*1X 2 X 2.5mm2 (JIS DPYC-2.5) *1 X 2 X 0.75mm2 (JIS TTYCS-1) (D)GPS RECEIVER
(IEC61162-1)
*1 X 2 X 0.75mm2
*4 X 2 X 0.75mm2 (JIS TTYCS-4) (JIS TTYCS-1) OTHER SSB
W. FACSIMILE
*1 X 2 X 2.5mm2 NAVTEX
(JIS DPYC-2.5) 3-*1 X 2 X 0.75mm2 (JIS TTYCS-4)
SELCALL

2 3 4 5 6 7 8 9 + - 2 3 4 5 6 7 8 9 + -
10 12

1 9 10 14 1 9 10 14 1 9 10 14 1 9 10 14
DISP_LINE+

DISP_LINE+

DISP_LINE+

DISP_LINE+
DISP_LINE-

DISP_LINE-

DISP_LINE-

DISP_LINE-
DISP_PWR
DISP_PWR

DISP_PWR
DISP_PWR

DISP_PWR
DISP_PWR

DISP_PWR
DISP_PWR
DISP_KEY
DISP_KEY

DISP_KEY

DISP_KEY
SYS_RST

SYS_RST
SYS_RST

SYS_RST
RS-485-A
RS-485-B

RS-485-A
RS-485-B

RS-485-A
RS-485-B

RS-485-A
RS-485-B
GND

GND
GND
GND

GND

GND
GND
GND

GND

GND
GND
GND

GND

GND
GND
GND
NC
NC

NC
NC

NC
NC

NC
NC

EXTENSION-1 EXTENSION-2 EXTENSION-1 EXTENSION-2

CONTROLLER CONTROLLER
DISP_LINE+

DISP_LINE+
DISP_LINE-

DISP_LINE-
DISP_PWR
DISP_PWR

DISP_PWR
DISP_PWR
DISP_KEY

DISP_KEY
SYS_RST
SYS_RST
RS-485-A
RS-485-B

RS-485-A
RS-485-B

NQD-2250 CONNECTION BOX NQD-2250 CONNECTION BOX

GND

GND
GND
GND

GND

GND
GND
GND
NC
NC

NC
NC

(OPTION) (OPTION)
GND GND
1 9 10 14 1 9 10 14
WHT

WHT
GRN

ORN

GRN

ORN
GRY

GRY
BRN
RED

BRN
RED
PNK

PNK
SKY

SKY
BLU

BLU
BLK

YEL

BLK

YEL
BLK(SHLD)

BLK(SHLD)
PR

PR
H-7ZCJD0343 (5m)

H-7ZCJD0343 (5m)

EXT. SP EXT. SP
NDF-369 NDF-369
KEYBOARD KEYBOARD

H- H-
7ZCJD0388 7ZCJD0388
(1.5m) KBD (1.5m) KBD
TRANSCEIVER PRT-C SP TRANSCEIVER PRT-C SP
PRT-S SER PRT-S SER
NDZ-227 NDZ-227
ACCESSORY
1
DTE ACCESSORY
1
DTE
PRT_PWR DC PRT_PWR DC (Option)
GND PRT GND PRT
GND GND
H- H-
NCM-2150
H-6JNKD00100B

H-6JNKD00100B
H-7ZCSC0205A

H-7ZCSC0205A

NCM-2150 7ZCJD0419 7ZCJD0419

(2m) MF/HF CONTROLLER (2m)
(1.6m)

(1.6m)

MF/HF CONTROLLER
(4m)

(4m)

(Option)

HANDSET KEY GND HANDSET KEY GND

NKG-800
NKG-800
PRINTER
PRINTER
(Option)
NQW-261 NQW-261
KEYER KEYER
HANDSET HANDSET

JSS-2250/2500 MF/HF RADIO EQUIPMENT (RACK TYPE: NCU-515A)

INTERCONNECTION DIAGRAM (1/2)

1-16
 46 DMC_OAL
47 DMC_OAS
48 DMC_SEL
49 DMC_DRQ
50 GND
51 DMC_PWR

DMC

TB206
52 DMC_RDY
53 DMC_DRA
*7 X 1 X 1mm2 (JIS MPYCS-7)
54 DMC_DAL
55 DMC_DAS
*2 X 1 X 16mm2 (JIS DPYC-16)
56 GND
*1 X 2 X 0.75mm2 (JIS TTYCS-1)
57 RMS_TX-A

Power source
AC100V/220V
58 RMS_TX-B
59 GND
*4 X 2 X 0.75mm2 (JIS TTYCS-4)
60 AME_TX-A
61 AME_TX-B
*2 X 1 X 2.5mm2 (JIS DPYC-2.5)

CONTROLLER
62 AME_RX-A

TB207

AC OUT
For Inm-C
63 AME_RX-B
CQD-2417 TERMINAL BOARD

64 GND
RMS/AME/422RX

DISTRESS MESSAGE
65 422_RX-A
66 422_RX-B
*1 X 2 X 1mm2 (JIS MPYCS-2)
67 AC_FAIL+

SYSTEM(IEC61162-1)
*2 X 1 X 1.5mm2 (JIS DPYC-1.5)
68 AC_FAIL-

REMOTE MAINTENANCE
*1 X 2 X 1mm2 (JIS MPYCS-2)

Max.3A
GPS DC1
69 CHG_ALM+
ALM

70 CHG_ALM-
TB208

*1 X 2 X 1mm2 (JIS MPYCS-2)

ALM

ALARM MANAGEMENT
71 BATT_LV+

EQUIPMENT(IEC61162-1)
*2 X 1 X 1.5mm2 (JIS DPYC-1.5)
72 BATT_LV-

MONITOR

Max.3A
ALM

GPS DC2
MONITOR
ALM
*2 X 1 X 1.5mm2 (JIS DPYC-1.5)

MONITOR

Max.3A
E｡LIGHT
AC U
AC U
AC V
*2 X 1 X 4mm2 (JIS DPYC-4)
AC IN/OUT

AC V

Max.10A
Inm-C DC
DC+
GPS +
GPS +
*2 X 1 X 4mm2 (JIS DPYC-4)
E.L +

Max.10A
VHF DC1
BUF +
INM +
TB504

VHF +
*2 X 1 X 4mm2 (JIS DPYC-4)
VHF +

Max.10A
VHF DC2
DC-
GPS -
GPS -
BATT OUT

E.L -
BUF -

INTERCONNECTION DIAGRAM (2/2)

INM -
VHF -
VHF -
1 9 2 10 7 21 22 23 24 25 26 27 8 28 29 30 31 32 33 34

*2 X 1 X 25mm2
1

BATT+
(JIS DPYC-25)

+
BATT+
+ + -

BATT-

-
TB502

-
BATT IN

*2 X 1 X 25mm2
2 3 4

BATTERY
BATT-
(JIS DPYC-25)

DC24V 200Ah
(Dockyard Supply)
GND

JSS-2250/2500 MF/HF RADIO EQUIPMENT (RACK TYPE: NCU-515A)

1-17
CONFIGURATION AND SPECIFICATIONS
 GND

1-18
1
1 GND
2 NC
3 NC
4 DISP_LINE+
5 DISP_LINE-

TB201
6 DISP_KEY

CNT
J211
W52
7 SYS_RST
8 RS-485-A

GND

9
9 RS-485-B

1
10 DISP_PWR

CONTROLLER
11 DISP_PWR
12 GND
W29 H-7ZCJD0442A

TB202
13 GND

J201
J101

5
14 GND

1
15 LINE_OUT+

CONTROLLER
16 LINE_OUT-
17 LINE_IN+
18 LINE_IN-
19 GND
20 EXT_KEY

TB203
NTD-2250/2500 TRANSCEIVER
21 SEL_BK
22 GND
23 +BK

ACCESSORY-1
24 -BK
25 GND
W30 H-7ZCJD0443A

11
J202
J102
NCU-515A MF/HF RADIO RACK

1
26 GPS_RX-A
27 GPS_RX-B
28 GND

ACCESSORY-1
29 DC_OPE+
30 DC_OPE-
31 R_CONT+

TB204
32 R_CONT-
33 GND
W31 H-7ZCJD0444A

J203
J103
34 +BK

TUNER
35 RBK

GPS ACCESSORY-2
36 GND

11
1
37 ATU_RBK
38 PA_MUTE
CONFIGURATION AND SPECIFICATIONS

39 ATU_RXD
40 GND

CQD-2417 TERMINAL BOARD

41 ATU_24V

TB205
42 ANT_CURR

TUNER
43 ATU_TXD
W32 H-7ZCJD0445A

J204
J104

44 GND

9
45 GND

1
46 DMC_OAL
ACCESSORY-2

47 DMC_OAS

ATU
J212
48 DMC_SEL
49 DMC_DRQ
50 GND
51 DMC_PWR

TB206
DMC
52 DMC_RDY
53 DMC_DRA
54 DMC_DAL
55 DMC_DAS
56 GND

11
1
57 RMS_TX-A
58 RMS_TX-B
59 GND
60 AME_TX-A
61 AME_TX-B
62 AME_RX-A
1.5 Radio rack internal wiring diagram

TB207
63 AME_RX-B
64 GND BATT_VOLT+

RMS/AME/422RX
65 422_RX-A DC_OPE
66 422_RX-B CHG_ALM

10
CHG
BATT_LOW_VOLT
1 567 8

1
1 TB209 5
67 AC_FAIL+ S.GND
68 AC_FAIL-
69 CHG_ALM+
70 CHG_ALM-

ALM

TB208
71 BATT_LV+

6
72 BATT_LV-

TX ANT
W42 H-7ZCJD0378 TX ANT
W44 H-7ZCJD0380 WKR/RX ANT
W46 H-7ZCJD0450 (Option) RX ANT

NCU-515A MF/HF RADIO RACK

WKR/RX ANT
RX ANT
J112

INTERCONNECTION DIAGRAM (1/2)

J111
PWR IN PWR CONT

W14 H-7ZCJD0390 (Option)

 FG
GRN

1
AC U AC IN(U)

9
AC U AC_U RED

BLU
RED

DC-
DC+
AC V AC_V WHT

10 2
AC V AC IN(V)

7
(A2,3,B2,3) DC +
(A1) + (7)
F11 3A

21
GPS + (8)
W5 H-7ZCJD0449A
W4 H-7ZCJD0448A
W6 H-7ZCJD0447A
W23 H-7ZCJD0446A

F12 3A

22
GPS + (9)

(Option)

BATT OUT(+)
F13 3A

23
1
E.L + (10)
1

BATT_VOLT+

W15 H-7ZCJD0391
BATT_VOLT-
F14 1A

24
BUF + (11) BATT_CURR+

RED
BATT_CURR-
(B1) + (12)
DC_OPE
F15 10A CHG_ALM

25
INM + BATT_LOW_VOLT
234 5
J701

GND
F16 10A
ACCESSORY

26
BATT_HI_TEMP+
PWR CONT

VHF +
BATT_HI_TEMP-
NBD-2250/2500 POWER SUPPLY

F17 10A BATT_LOW_TEMP+

27
VHF + BATT_LOW_TEMP-
12

8
J3

(A7,8,B7,8) DC -
W51

(A6) (1)
PWR OUT

-
FG

F21 3A

28
GPS - (2)

F22 3A

29
GPS - (3) W1 7ZCJD0347
BATT OUT(-)
AC IN

F23 3A

30
E.L - (4)

F24 1A

31
BUF - (5)
BLK

(B6) - (6)
J1

F25 10A

32
AC IN

INM -
F26 10A

33
TB504

VHF - W2 7ZCJD0348
J2

NCU-515A MF/HF RADIO RACK

F27 10A

34
DC IN

VHF -
BATT OUT

H-7JTJD0051A

BATT(+)
W53

(9,10,11,12) W3 7ZCJD0349
1

INTERCONNECTION DIAGRAM (2/2)

BATT+ RED
BATT
NBB-724 BATTERY CHARGER
GND

TB502

BATT+ (13,14,15)
3

BATT- BATT(-)
(5,6,7)
4

BATT-
H-7JTJD0049

BLK
(1,2,3,4)

1-19
CONFIGURATION AND SPECIFICATIONS
CONFIGURATION AND SPECIFICATIONS

1-20
 INSTALLATIONS

2. INSTALLATIONS

2.1 Installation Procedure

The following procedure is for installing the equipment.

① Selecting a location to install the equipment

Carefully discuss the following points with the ship's owner when selecting a location.

• Install the equipment in a well ventilated area that is not humid.

• Install the MF/HF controller (NCM-2150) and the data terminal (NDZ-227) on the bridge or
someplace near the ship's controls. (If two controllers are being installed, install one near the
ship's controls.)

• Refer to the "External dimensions and equipment overview" and consider the maintenance of the
equipment when selecting a location. When installing the radio rack or console (NCU-515A/
531A) hereinafter called the main unit, work space is needed for pulling out units.

• Ground the main unit, the antenna tuner (NFC-2250/2500), the MF/HF controller (NCM-2150),
and the data terminal (NDZ-227) to the ship. Especially ground the MF/HF antenna tuner by
soldering one side of a copper sheet to the ship as explained later.

• The MF/HF controller (NCM-2150) is provided with a 5 meters length cable, but it can be relayed
through the connection box (NQD-2250) and extended up to 70 meters (between the transceiver
and the controller). In this case, it is needed to use one power cable DPYC-2.5 per one MF/HF
controller between the main unit and the connection box.

• The Antenna tuner (NFC-2250/2500) can be relayed through the Junction box (NQD-2253) and
extended up to 30 meters.

• Install the equipment far enough away from the compass to protect the compass.

NTD-2250 Transceiver NTD-2500 Transceiver

Standard compass: 1.1 m Standard compass: 1.1 m
Steering compass: 0.7 m Steering compass: 0.6 m

NBD-2250 Power supply NBD-2500 Power supply

Standard compass: 1.1 m Standard compass: 0.9 m
Steering compass: 0.7 m Steering compass: 0.6 m

NBB-714 Battery charger NBB-724 Battery charger

Standard compass: 1.5 m Standard compass: 1.0 m
Steering compass: 0.8 m Steering compass: 0.6 m

NFC-2250 Antenna tuner NFC-2500 Antenna tuner

Standard compass: 1.1 m Standard compass: 1.0 m
Steering compass: 0.7 m Steering compass: 0.6 m

NCM-2150 MF/HF controller NQD-2250 Connection box

Standard compass: 2.0 m Standard compass: 0.1 m
Steering compass: 1.5 m Steering compass: 0.1 m

NDZ-227 Data terminal NQD-2253 Junction box

Standard compass: 0.7 m Standard compass: 0.3 m
Steering compass: 0.4 m Steering compass: 0.1 m

2-1
INSTALLATIONS

② Selecting a position for and installing the antenna

The antenna is a conductor that emits RF energy (radio waves) from the transmitter, and receives
signals from other stations. There are many types of antennas. The most common of which are the
vertical whip antenna (10 meters long) and the wire antenna (10 to 20 meters long). Follow the
recommendations below for both types.

• Install the antenna as far as possible from any structures, wires, or other antennas to reduce any
effect to tuning or radiation patterns.

• Use an insulator with sufficient pressure resistance, and do not paint or get sand on it.

• Once the antenna is installed it is a part of the radio equipment and grounding it is considered
very important.

• The antenna's efficiency is proportional to the area of the antenna's ground (RF ground), so large
metal ships result in efficient antennas. Therefore, for smaller non-metal boats, provide sufficient
ground area (normally 30 m 2 or more).

• Connect all antenna grounds to the GND terminal of the antenna tuner.

• Refer to "Examples of antenna installations" in this manual for methods to install antennas.

Examples, particularly for transmitting antennas, of suitable and unsuitable grounds are described
below. In figure (a), the transmitting antenna, antenna tuner, radio, controller, and the user are
included as part of the radiating objective. Not only does this reduce efficiency, it also creates the
risk of electrocuting the user. Figure (b) shows an ideal example, in which the radiating objective
includes the transmitting antenna and the antenna tuner only.

2-2
 INSTALLATIONS

Transmitting antenna

* From this potential all

devices can become
antenna, i.e. there is a
chance of emissions
from the controller.

Antenna tuner Radio/controller

Poor ground line

Counterpoise
(RF ground)

a) Example of unsuitable antenna grounding

Transmission
送信アンテナ antenna

*※RFグラウンドに近いためコントロー
There are no emissions
from the controller because
ラなどからは輻射されない。
it is close to the RF ground.

Good ground
確実なアース アンテナ
Antenna tuner 無線機本体／
Radio/controller
チューナ コントローラ

Counterpoise
カウンタポイズ
(RF ground)
（RFグラウンド）

b) Example
b) of correct antenna grounding
適切なアンテナ接地例

2-3
INSTALLATIONS

③ Cable layout
Refer to the interconnection diagrams in chapter 1, the external dimensions and equipment
overview in this chapter, and the following recommendations to install the cables.

• Keep the cables as short as possible.

Note) As mentioned above, the maximum allowable distances between the main unit and the
MF/HF controller (NCM-2150) and between the main unit and the antenna tuner
(NFC-2250/2500) are 70 meters and 30 meters, respectively.

• Be sure to use twisted pair cable for control cables to connect the main unit, connection box
(NQD-2250), and the MF/HF controller (NCM-2150).

• When cutting cables, allow enough slack to connect and disconnect them from the terminals and
move the equipment for maintenance.

• Install the cables as far as possible from the smokestack or things that are hot. Protect the
antenna cables with a heat shield if they might be exposed to hot gas from the smokestack.

• Keep the cables as far as possible from magnetic compasses. The minimum distance from a
magnetic compass is 2 meters for braided armor cables and 1 meter for other cables.

• Use TTYCS (twisted pair) cable wherever it is specified in the interconnection diagram, even
when replacing the radio equipment.

④ Equipment installation
Refer to the external dimensions and equipment overview in this chapter when installing the
equipment.

⑤ Wiring
Refer to the interconnection diagrams in chapter 1 and the external dimensions and equipment
overview in this chapter when wiring the equipment.
Note) After connecting the wires but before turning on the power, check cable connections, wires
to the terminals, and the connecting bar setting for the AC input voltage of the battery
charger (NBB-714/724).

Additionally, regarding initial settings and operation check, refer to the service manual.

2-4
 INSTALLATIONS

2.2 External dimensions and equipment overview

2.2.1 NCU-515A Radio Rack

Attention

When removing or installing the NTD-2250/2500 Transceiver

and/or the NBD-2250/2500 Power supply, handle the transceiver
cables so that they are not pulled forcedly. If the connector lock
is caught to things such a cable as shown at right, it may be
damaged or broken.

2.2.1.1 External dimensions and installation space

Unit: mm
Weight: Approx. 90kg/96kg
Color: N4, N7

2-5
INSTALLATIONS

2-6
 INSTALLATIONS

2.2.1.2 Installation

（１） Preparation (removal of the power supply and the battery charger)

In order to secure the work space for installation, remove the power supply (NBD-2250/2500) and the
battery charger (NBB-714/724) from the radio rack NCU-515A.

1) Remove the screws of NBB-714/724, NBD-2250/

2500, and the blank panel.

2) Pull out NBB-714/724, and then remove the

cables on the back side and the earth wire.

3) Pull out NBD-2250/2500, and then remove the

cables on the back side.

Then remove the lowermost blank panel

Note: After the installation and the cables wiring

mentioned below, restore the power supply
and the battery charger to normal state.

2-7
INSTALLATIONS

（２） Installation

After removing the power supply, the battery charger

and the blank panel, fix four places in the radio rack
bottom with the four bolt nuts as shown at right.
Preliminarily, remove the CQD-2417 Terminal board
according to the following procedures.

1) Remove the cover of CQD-2417.

2) Remove the five cables. And also remove the

cable ties fixing the rack cables to the cable
clamp.

3) Remove the terminal board with the metal fitting.

After fixing the rack with the bolts and nuts,

restore the every part to normal state.

2-8
 INSTALLATIONS

（３） Connecting the ground

After installation, attach a grounded plate at the position of the radio rack bottom back shown in the
following figure.

Weld an earth plate. (A)

Earth plate

Weld around
Detail A. the earth plate.

2-9
INSTALLATIONS

2.2.1.3 Connecting the power cable

CAUTION
When connecting the battery to the rack/console, first connect the cable to the
radio rack/console before connecting to the battery.

When connecting the AC mains, first turn off the power at the switchboard before
wiring the cables to the equipment.

（１） Connecting the battery

Observe carefully the polarity (from the left, [+], [+], [-], [-]) on the terminal block, and connect battery
cables to the terminal block according to the following procedure:

BATT+: Standard 25 mm 2 x 2 cables

BATT-: Standard 25 mm 2 x 2

1) Strip 18 mm at insulating sheath the tip of its electric cable.

2) Loose a desirable screw on the terminal block, and then insert the appropriate electric
cable corresponding with the terminal’s battery DC (+/-) polarity.
3) Tighten the above screw, and then check the electric cable is securely fixed.
Fix other electric cables with the same method.

2-10
 INSTALLATIONS

（２） Connecting the AC mains

Connect AC mains cables to the terminal box according the following procedure:

AC power supply terminal (V):

Standard 16 mm 2 x 2 cables

AC power supply terminal (U):

Standard 16 mm 2 x 2 cables

1) Strip 18 mm at insulating sheath the tip of its electric cable.

2) Loose a desirable screw on the terminal block, and then insert the appropriate electric
cable corresponding with the terminal’s AC (U/V) phase.
3) Tighten the above screw, and then check the electric cable is securely fixed.
Fix other electric cables with the same method.

2-11
INSTALLATIONS

（３） Connecting the GPS power supply

Observe carefully the polarity (the left terminal block [+], and the right terminal one [-]), and connect
GPS power supply cables to the terminals in the blocks according to the following procedure:

DC + DC -

Fuse cases **

1) Strip 10 mm at insulating sheath the tip of its electric cable.

Insert a cable (standard
2) Slide a thin flathead screwdriver* to the back of a
1.5 mm 2 ).
slit at a desirable terminal. During the above
sliding screwdriver condition, insert an
appropriate DC (+/-) polarity electric cable to the
back of the slit.
(*) A suitable blade of a screwdriver for this work:
- Thin flathead and straight blade tip shape.
- No curving blade tip shape.
- Sufficient hardness blade. Thin flathead
OK NG screwdriver

3) Remove the screwdriver, and then confirm that

the cable is securely fixed.

(**) Replace the fuses as follows.

(Refer to the manual of the radio rack in detail.)

- For the small fuse cases, pull out and replace

the internal fuse as shown at right.
- For the large fuse cases, pull the upper side
and open it to replace the internal fuse as
shown at lower right.

2-12
 INSTALLATIONS

2.2.1.4 Connecting the signal lines

Connect an each signal line to its corresponding terminal on the terminal board (CQD-2417). Further,
refer to the details of the each signal shown in “2.2.1.7 Terminal description”.

① Slide a thin flathead screwdriver (blade tip width: 2.5

Flat-head
マイナスドライバ screw driver
- 3.5 mm) all the way into the slit as shown in the
figure to the right and then insert the signal line*.

*) Compatible wire sizes: 0.2 - 2.5 mm 2

Slit
スリット
(AWG 24~12)
Stripped length: 8 mm
Strip length: 8 mm

Signal line port

信号線挿入口

② Remove the screwdriver and make sure that the

signal line is securely connected.

③ When the wiring is finished, secure the cables in a

bundle with the cable clamp.

2-13
INSTALLATIONS

2.2.1.5 Connecting the coaxial cables

Connect the coaxial cables to the radio unit according to

the following procedures:
In addition, the coaxial connectors (panel mount
receptacle type) which are connected plugs of the
coaxial cables are on the right side of the lowest part in
the radio rack.

1) Process the each tip of the coaxial cables, and then connect the M type connector.
(Refer to "2.2.11.3 Cable processing" for the details of a processing procedure.)

2) Connect the each coaxial cables to the connectors according to the antenna distinction names of
TX ANT, WKR/RX ANT, and RX ANT respectively.

Coaxial Cables

RX ANT (Option)
(Coaxial cable for the specific RX antenna)

WKR/RX ANT
(Coaxial cable for the WKR/RX antenna)

TX ANT
(Coaxial cable for the antenna tuner)

2-14
 INSTALLATIONS

2.2.1.6 Removal of the eyebolts

If needed, remove eyebolts according to the following procedures.

- Remove the side panels.
- Remove the nuts on the back of the top panel with a wrench etc. and then remove the eyebolts.
- Attach the plastic bolts instead of the eyebolts.

Plastic bolt

Side panel

Side Panel

2-15
INSTALLATIONS

2.2.1.7 Terminal description

CQD-2417 TB201 - 204

Connection
No. Name Description
point
1 GND Ground for shielded connections
2 NC
(not used)
3 NC
4 DISP_LINE+ 600 Ω balanced, 0dBm
5 DISP_LINE- AF receiver signal
6 DISP_KEY PTT/KEY line
7 SYS_RST System reset line NCM-2150
MF/HF
8 RS-485-A Interface for RS-485 communication （ 57.6kbps / 8bit/ Controller
9 RS-485-B none）
10 DISP_PWR 24 VDC, maximum 3 A, MF/HF controller NCM-2150
11 DISP_PWR dedicated power supply
12 GND
Ground
13 GND
14 GND Ground for shielded connections
15 LINE_OUT+
Receiving signal output (600 Ω balanced, 0dBm)
16 LINE_OUT-
Selcall or
17 LINE_IN+ other
Transmitting signal input (600 Ω balanced, 0dBm)
18 LINE_IN- external
device
19 GND Ground for shielded connections
20 EXT_KEY External transmission request signal (Transmit=L)
21 SEL_BK Selcall transmission request signal (Transmit=L) Selcall
22 GND Ground for shielded connections device
Power supply for running -BK circuit of external device External
23 +BK
(+24 V, max. 0.5A) radio,
24 -BK -BK input/output signal weather
25 GND Ground for shielded connections FAX, etc.

26 GPS_RX-A IEC61162-1 compliant, 4800 bps, receiving only

27 GPS_RX-B (NMEA0183 V1.5, V2.0, V2.3: GGA/GLL/RMC/GNS/ZDA) GPS
28 GND Ground for shielded connections
29 DC_OPE+
Acknowledgement signal input when running on DC power Not used
30 DC_OPE-
Inmarsat-C power on permission signal on a battery
31 R_CONT+ operation
Set either Dual or Single on NCM-2150 menu F1.2.4.2
BATT use set. INM-C(SES)
32 R_CONT-
(Operation enable: Dual / operation disable: Single)
33 GND Ground for shielded connections
Power supply for running -BK circuit of external device External
34 +BK
(+24 V, max. 0.5A) radio,
35 RBK RBK output signal (Max. 1.5A) weather
36 GND Ground for shielded connections FAX, etc.

2-16
 INSTALLATIONS

CQD-2417 TB205 - 208

Connection
No. Name Description
point
ATU_RBK Transmitter ON/OFF signal* for such as ANT switch
37
(ON=L)
38 PA_MUTE Transmission inhibit signal (Inhibit=L)
39 ATU_RXD Serial receiving signal (4.8 kbps/7 bits/even/1 stop)
40 GND Serial receiving signal ground NFC-2250/2500
41 ATU_24V Power for the antenna tuner (+24 V, max. 1A) antenna tuner
etc.
42 ANT_CURR Antenna current signal input
43 ATU_TXD Serial transmitting signal (4.8 kbps/7 bit/even/1 stop)
44 GND Serial transmitting signal ground
45 GND Ground for shielded connections
Others reception alarm signal output (NCH-321A is not
46 DMC_OAL
used)
Others reception alarm stop signal input (NCH-321A is
47 DMC_OAS
not used)
Device selection/distress message transmit stop signal
48 DMC_SEL
input
49 DMC_DRQ Distress alert request signal input
50 GND Ground
NCH-321A DMC
51 DMC_PWR Common power supply output (+10V, max. 100 mA)
52 DMC_RDY Device selection ready signal output
53 DMC_DRA Distress-alert-request ACK signal output
54 DMC_DAL Distress message reception alarm signal output
Distress reception alarm stop signal input (NCH-321A is
55 DMC_DAS
not used)
56 GND Ground for shielded connections
57 RMS_TX-A IEC61162-1 compliant, 4800 bps, transmitting only
58 RMS_TX-B Output for remote maintenance system RMS
59 GND Ground for shielded connections
60 AME_TX-A IEC61162-1 compliant, 4800 bps, transmitting only
61 AME_TX-B
62 AME_RX-A IEC61162-1 compliant, 4800 bps, receiving only AME
63 AME_RX-B
64 GND Ground for shielded connections
65 422_RX-A
IEC61162-1 compliant, 4800 bps, receiving only Not used
66 422_RX-B
67 AC_FAIL+ AC power supply OFF signal output
AC power supply OFF is outputted with a contact signal.
68 AC_FAIL- (AC OFF: Short)
69 CHG_ALM+ Charger abnormal signal output
Charger abnormal is outputted with a contact signal. ALM MONITOR
70 CHG_ALM- (Charger abnormal: Short)
71 BATT_LV+ Battery low voltage signal output
Battery low voltage is outputted with a contact signal.
72 BATT_LV- (Battery low voltage: Short)

* After transmitting, the ATU_RBK keeps L output for 1 to 1800 seconds (factory default: 180 seconds).

2-17
INSTALLATIONS

H-7JTJD0051A TB504
Connection
No. Name Description
point
1 AC U
9 AC U AC input AC switchboard
AC90V~132V, AC180V~264V, max. 60A
2 AC V Permissible wire diameter max. 35mm
2 etc.

10 AC V
7 DC + DC output (battery) for MF/HF
DC21.6V~31.2V, max. 40A NBD-2250/2500
8 DC - Permissible wire diameter max. 16mm
2

21 GPS +
DC output (battery) for GPS
28 GPS - DC21.6V~31.2V, max. 3A
2 GPS
22 GPS + Permissible wire diameter max. 4mm
Short circuit protection with the fuse
29 GPS -
23 E.L + DC output (battery) for emergency lights
DC21.6V~31.2V, max. 3A
2 Emergency light
30 E.L - Permissible wire diameter max. 4mm
Short circuit protection with the fuse
24 BUF + DC output (battery) for GPS buffers
DC21.6V~31.2V, max. 1A
2 GPS BUFFER
31 BUF - Permissible wire diameter max. 4mm
Short circuit protection with the fuse
25 INM +
DC output (battery) for INM-C
32 INM - DC21.6V~31.2V, max. 10A
2 INM-C (SES)
35 INM + (*1) Permissible wire diameter max. 4mm
Short circuit protection with the fuse
36 INM - (*1)
26 VHF +
DC output (battery) for VHF
33 VHF - DC21.6V~31.2V, max. 10A
2 VHF
27 VHF + Permissible wire diameter max. 4mm
Short circuit protection with the fuse
34 VHF -
*1: INMARSAT C extension terminal.

H-7JTJD0049 TB502
Connection
Number Name Explanation
destination
1 BATT +
2 BATT + DC input (battery)
DC21.6V~31.2V, max. 50A (*2) BATTERY
3 BATT - Permissible wire diameter max. 35mm
2

4 BATT -
*2: BATT breaker trip current of NBB-724 charger.

2-18
 INSTALLATIONS

2.2.2 NTD-2250/2500 Transceiver

2.2.2.1 External dimensions

Unit: mm
Weight: Approx. 15 kg/17kg
Color: Munsell N4

Note) This figure shows the NTD-2250.

Incase of the NTD-2500, 3 fans

are mounted on the back.

2-19
INSTALLATIONS

2.2.3 NBD-2250/2500 Power Supply

2.2.3.1 External dimensions

Unit: mm
Weight: Approx 15 kg/18kg
Color: N4

2-20
 INSTALLATIONS

2.2.4 NBB-714 Battery Charger

2.2.4.1 External dimensions

● Rack mount type

Unit: mm
Weight: Approx. 8.4 kg
Color: N4

● Stand-alone type

Unit: mm
Weight: Approx. 8.6 kg
Color: N4

2-21
INSTALLATIONS

Note: As the factory default, the NBB-714 is the stand-alone type. To install it into the radio rack,
remove the bottom bracket and mount the optional rack mount kit (7ZZJD0073) as below.

(Figure for removing the bottom bracket and mounting the rack mount bracket)

2-22
 INSTALLATIONS

2.2.4.2 Connecting the signal lines

Use the specialized cables as shown below to connect the battery charger (NBB-714).

2-23
INSTALLATIONS

2.2.4.3 Setting the AC input voltage (110 VAC/220 VAC)

Open the cover on the back panel indicated by the arrow in the drawing and use the short plug to
switch the AC input voltage according to the setup manual provided. The factory setting is 220 VAC.

2-24
 INSTALLATIONS

After setting the AC input voltage, remove the appropriate label for the input voltage from the voltage
switching tag (following figure (1)) and stick it in the box on the voltage label (following figure (2)).

(2)
② Voltage label
電圧表示ラベル

(1) Voltage switching tag

Cut out

2-25
INSTALLATIONS

2.2.4.4 Setting the battery charging voltage

The battery charger (NBB-714) is only applied to batteries unneeded maintenance. Therefore the
battery charger (NBB-714) is set at the factory for lead sealed batteries.

Battery type and charging voltages

Type Model number Floating charge voltage
Lead (sealed) MSE 26.8V

Further adjust charging voltage according to the following procedure:

① Turn ON the AC switch and the BATT breaker.

Note:
• If there is a time lag at turning ON the AC switch and the BATT breaker, an alarm may
sound. This is not a malfunction, it happens because the battery charger alarm function
detects that the AC input is abnormal or the BATT breaker is off.
• If the BATT breaker is turned on while the battery poles are reversed, an internal
protection circuit trips the BATT breaker.
• When the AC switch and the BATT breaker are turned OFF after running the equipment,
an alarm may sound. This is not a malfunction, it happens during discharging a residual
electric charge.

② During checking the battery voltage with a tester, turn the variable resistor at the filter reverse
side shown the following figure arrow in order to adjust the floating charge voltage.

2-26
 INSTALLATIONS

2.2.4.5 Accessories Terminals

Functions and explanations of the accessory terminal located on the back panel are shown below.

No. Name Description

1 ALARM (+)
When an alarm occurs, output is open circuit.
2 ALARM (-)

3 ALARM MUTE (+)

When it is shorted at occurring alarm, its alarm is muted.
4 ALARM MUTE (-)

2.2.4.6 Other functions (protection circuit)

¾ Charge warning function

When the AC switch is off (AC input abnormal) and the BATT breaker is on (AC FAIL
condition), or when the AC switch is on and the BATT breaker is off (CHG ALARM condition),
the AC FAIL/CHG ALARM LED lights and a buzzer sounds.
* Auto recovery when the AC switch is on and/or the BATT breaker is on.

¾ Over voltage detection function

When the BATT voltage is more than +32.2 ~ 37.0 V, the connection between the charging
circuit and the battery is automatically broken (The BATT breaker is tripped). Also, the CHG
ALARM LED lights, and a buzzer sounds.
* When the BATT voltage is less than +32V, it is recovered by turning the AC breaker off and
then on, and turning the BATT breaker on.

¾ Temperature monitoring function 1

When a high temperature of over 60 C is detected on the circuit, the FAN starts cooling.
* The FAN automatically turns off when the temperature decreases.

¾ Temperature monitoring function 2

When a high temperature of over 80 C is detected, the charging circuit stops. Also, the CHG
ALARM LED lights, and a buzzer sounds.
* Auto recovery after temperature decreases.

¾ Low voltage detection function

When a drop in battery voltage (21.5 V or less) is detected, the BATT LOW VOLT LED lights,
and a buzzer sounds. When AC input is abnormal (during discharge) and the battery voltage
goes less than 19.5 V, the battery breaker is tripped in order to protect overcharge to the
battery. This does not operate for momentary voltage fluctuations from sudden currents when
starting the device due to 0.1 to 0.5 second hysteresis.
* Auto recovery when the battery voltage goes above 23.5 V during turning on the AC switch.

¾ Charge circuit
When the battery voltage is less than 16 V, current is reduced due to the fold-back type
drooping characteristic (Max. 10 A).

¾ AC input over voltage protection

When an AC input of over AC 135 V (100 V setting) or AC 270 V (220 V setting) is detected,
the equipment is protected with blown the FUSE.

¾ DC input over voltage protection

When a BATT input of over +32.2 ~ 37.0 V is detected, the BATT breaker is tripped.

2-27
INSTALLATIONS

2.2.5 NBB-724 Battery Charger

2.2.5.1 External dimensions

● Rack mount type

Unit: mm
Mass: Approx. 12kg
Color: N4

● Stand-alone type

Unit: mm
Mass: Approx. 12 kg
Color: N4

Note: As the factory default, the NBB-724 is the stand-alone type. To install it into the radio rack, refer
to “Figure for removing the bottom bracket and mounting the rack mount bracket” in the 2.2.4.1
External dimensions for the NBB-714 mentioned above.

2-28
 INSTALLATIONS

2.2.5.2 Connecting the signal lines

Use the specialized cables as shown below to connect the battery charger (NBB-724).

BATT BATT OUT AC IN

7ZCJD0349

7ZCJD0348

7ZCJD0347
Battery
NBD-2150 AC110V/
DC24V
DC24V IN AC220V
200Ah

2-29
INSTALLATIONS

2.2.5.3 Setting the AC input voltage (110 VAC/220 VAC)

Open the cover on the back panel indicated by the arrow in the drawing and use the short plug to
switch the AC input voltage according to the setup manual provided. The factory setting is 220 VAC.

After setting the AC input voltage, remove the appropriate label for the input voltage from the voltage
switching tag ((1) on the following page) and stick it in the box on the voltage label ((2) on the following
page).

2-30
 INSTALLATIONS

② Voltage
電圧表示ラベル label

① Voltage
電圧切替タグ switching tag

Cut out

2-31
INSTALLATIONS

2.2.5.4 Setting the battery charging voltage

The battery charger (NBB-724) is set at the factory for lead acid batteries. To use other types of
batteries, set it as shown below.

Reference: Battery types and charging voltages

Type Model number Floating charge voltage Equalizing charge voltage
Lead SS-200 26.2 V 29.4 V
Lead (sealed) MSE 26.8 V 26.8 V
Alkali AM-P 28.4 V 30.4 V

Factory default setting

① Open the blank panel indicated by the arrow in the diagram below.

② Turn the AC and DC breakers on. Check that the FLOAT lamp is lit to confirm floating charge
mode is on.

Note:
• An alarm sounds if the AC breaker is turned on before the BATT breaker, this is not a
malfunction, it happens because the battery charger alarm function detects that the
BATT breaker is off.
• If the BATT breaker is turned on while no battery is connected or the poles are
reversed, an internal protection circuit trips the BATT breaker.

③ Use the voltmeter on the panel to check the battery charger's voltage as you turn the control
RV2 inside the blank panel to set the floating charge voltage for the battery being used.

2-32
 INSTALLATIONS

④ After setting the floating charge voltage, move switch SW2 up to light the EQUAL lamp shown
below, to turn on equalizing charge mode.
Caution: Equalizing charge mode can be turned on by using the CHARGE switch on the
panel, but if the charge voltage goes below 3A it automatically returns to float
charge.

⑤ Use the voltmeter on the panel to check the battery charger's voltage as you turn the control
RV3 inside the blank panel to set the equalizing charge voltage for the battery being used.

⑥ After finishing the settings, move switch SW2 down (floating charge mode), and then replace
the blank panel.

2.2.5.5 Prohibiting equalizing charging

Because equalizing charge is unnecessary for lead sealed batteries, set the floating charge voltage
and the equalizing charge voltage to 26.8 V, and then move switch SW5 up as indicated by the arrow
below, inside the blank panel to prohibit equalizing charge (CHARGE switch is disabled).

2-33
INSTALLATIONS

2.2.5.6 Details on switches and controls in the blank panel

Functions and explanations of switches and controls in the blank panel are shown below.

Factory
No. Functions Setting Status after configuration
default
Equalizing charge timer Up Normal setting (timeout 10 h) z
SW1
(for factory testing) Down Test setting (timeout 10 sec)
Floating/equalizing charge voltage Up Equalizing charge voltage mode
SW2
switching (for voltage adjustment) Down Floating charge voltage mode z
Up Disabled
SW3 Over discharge prevention Enabled
Down (BATT breaker tripped at 19.5 V or less)
z
Up Enabled
SW4 BATT HI/LOW TEMP input control
Down Disabled z
Prohibit equalizing charge Up Enabled
SW5
(CHARGE SW operation prohibited) Down Disabled z
Up Disabled
SW6 Detect BATT connection Enabled
Down (detects disconnected or reversed connections)
z

¾ SW1 Equalizing charge timer (Remarks: Do not operate this switch.)

With the standard settings, when equalizing charge mode is set with the panel's CHARGE
switch, the device automatically returns to floating charge mode after 10 hours. Also, when
the equalizing charge current is less than 3 A, the device automatically returns to floating
charge mode.

¾ SW2 Floating/equalizing charge voltage switching

Used to switch the charging mode when adjusting the floating charge voltage and the
equalizing charge voltage for the battery connected.

¾ SW3 Over discharge prevention (Remarks: Do not operate this switch.)

When enabled, the BATT breaker is tripped when the battery voltage is less than 19.5 V.
Note 1: Functions only during discharge.
Note 2: Does not operate for momentary (approx 0.1sec or less) voltage fluctuations
from surges when starting the device.

¾ SW4 BATT HI/LOW TEMP input control

When this switch is enabled and a battery temperature detection signal *1 is connected to the
accessory terminal (described later) BATT HI TEMP or BATT LOW TEMP terminal, charging
voltage is output according to the input battery temperature (high or low).
*1. Output signal of the thermal lead switch attached to the battery.

¾ SW5 Prohibit equalizing charge

When enabled, the panel's CHARGE switch is disabled. Used to prohibit equalizing charge of
a lead sealed battery.

¾ SW6 Detect BATT connection (Remarks: Do not operate this switch.)

When enabled, if the battery is connected in reverse or a battery is not connected, the
protection circuit trips the BATT breaker.

2-34
 INSTALLATIONS

No. Functions Factory setting

RV2 Floating charge voltage adjustment control 26.2 V

RV3 Equalizing charge voltage adjustment control 29.4 V

RV4 Charging voltage adjustment control when BATT LOW TEMP detected 27.5 V

RV5 Charging voltage adjustment control when BATT HI TEMP detected 25.3 V

¾ RV2 Floating charge voltage adjustment control

Used when adjusting the floating charge voltage.

¾ RV3 Equalizing charge voltage adjustment control

Used when adjusting the equalizing charge voltage.

¾ RV4 Charging voltage adjustment control when BATT LOW TEMP detected
Used to adjust the higher charging voltage output to prevent insufficient charging when low
temperatures are detected on the battery.

Detecting low battery temperatures and adjusting charging voltage)

① Flip SW4 up to enable BATT HI/LOW TEMP input control.
② Short-circuit accessory terminal BATT LOW TEMP #11 (+) and #12 (-).
③ Adjust RV5 to the appropriate value. (Adjustment range: 26 to 28 V)
④ Disconnect the BATT LOW TEMP short, and connect the signal line of the thermal lead
switch used for low temperature detection on the battery to that terminal.

¾ RV5 Charging voltage adjustment control when BATT HI TEMP detected

Used to adjust the lower charging voltage output to control temperature increases when high
temperatures are detected on the battery.

Detecting high battery temperatures and adjusting charging voltage)

① Flip SW4 up to enable BATT HI/LOW TEMP input control.
② Short-circuit accessory terminal BATT HI TEMP #9 (+) and #10 (-).
③ Adjust RV4 to the appropriate value. (Adjustment range: 24 to 26 V)
④ Disconnect the BATT HI TEMP short, and connect the signal line of the thermal lead
switch used for high temperature detection on the battery to that terminal.

2-35
INSTALLATIONS

2.2.5.7 Accessory terminals

Functions and explanations of the accessory terminal located on the back panel are shown below.

No. Name Description

1 BATT VOLT (+)

BATT OUT voltage monitor output (max. 1.0 A)
2 BATT VOLT (-)

3 BATT CURR (+)

Outputs voltage proportional to the charge and discharge voltage as
an analog value
4 BATT CURR (-)

5 DC OPE Outputs as open collector when AC power is off (max. 24 V, 200 mA)
Outputs as open collector when a charging alarm occurs
6 CHG ALARM
(max. 24 V, 200 mA)
Outputs as open collector when a low voltage alarm occurs
7 BATT LOW VOLT
(max. 24 V, 200 mA)
8 GND GND

9 BATT HI TEMP (+) Input terminal for the thermal lead switch* signal for high temperature
detection attached to the battery
10 BATT HI TEMP (-) *35MLR, 40MLR, 45MLR, 50MLR, and 55MLR can be connected

11 BATT LOW TEMP (+) Input terminal for the thermal lead switch* signal for low temperature
detection attached to the battery
12 BATT LOW TEMP (-) *5BLR can be connected

2.2.5.8 Other functions (protection circuit)

¾ Charging warning function

When the AC breaker is on and the BATT breaker is off, the FLOAT/EQUAL LED goes out, the
CHG ALARM LED lights, and a buzzer sounds.
* Auto recovery when the BATT breaker is on.

¾ Over voltage detection function

Functions only when charging. When the BATT voltage is +34 V, the connection between the
charging circuit and the battery is automatically broken. Also, the FLOAT/EQUAL LED goes
out, the CHG ALARM LED lights, and a buzzer sounds.
* Recovered by turning the AC breaker off and then on.

¾ Temperature monitoring function 1

When a high temperature of over 60 C is detected on the circuit, the FAN starts cooling.
* The FAN automatically turns off when the temperature decreases.

¾ Temperature monitoring function 2

When a high temperature of over 80 C is detected on the circuit, the charging circuit stops.
Also, the FLOAT/EQUAL LED goes out, the CHG ALARM LED lights, and a buzzer sounds.
* Auto recovery after temperature decreases.

2-36
 INSTALLATIONS

¾ Low voltage detection function

When a drop in battery voltage (21.5 V or less) is detected, the BATT LOW VOLT LED lights
and a buzzer sounds. Does not operate for momentary voltage fluctuations from sudden
currents when starting the device due to 0.1 to 0.5 second hysteresis.
* Auto recovery when the battery voltage goes above 23.5 V.

¾ Charging circuit
When the battery voltage is less than 18 V, voltage is reduced due to the fold-back type
drooping characteristic, regardless of the charging mode (float or equalized).

¾ AC input over voltage protection

When an AC input of over AC 135 V (100 V setting) or AC 270 V (220 V setting) is detected,
the AC breaker is tripped.

¾ DC input over voltage protection

When a BATT input of over DC 36 V is detected, the BATT breaker is tripped.

2-37
INSTALLATIONS

2.2.6 NCM-2150 MF/HF Controller

2.2.6.1 External dimensions and installation space

Unit: mm
Weight: Approx. 1.3 kg
Color: N4

2-38
 INSTALLATIONS

2.2.6.2 Installation

（１） RS-485 signal line terminator settings

The RS-485 lines are used for signals between the NTD-2250/2500 Transceiver and the NCM-2150
MF/HF controller, so terminators must be placed on the first and last units. If there is only one MF/HF
controller this setting is not necessary because the load is terminated (on) at the MF/HF controller at
the factory. However, if there are 2 MF/HF controllers connected, the terminator on the unit nearest the
transceiver must be turned off.

To set the terminator to on or off, after checking that the breakers on the power supply (NBD-2250/
2500) is turned off, remove the back cover (shaded area in diagram) and short the TB101 jumper pin
on the CMV-3775 AF CONT UNIT appropriately as below.

TB101
1 2 3
Terminate
ON

TB101
1 2 3
Terminate
OFF

Note1. This termination also can be set on the CQD-2250 CONNECTION BOARD of the NQD-2250
Connection box. However do not set the both of the terminators to ON or OFF carelessly.

Note2. If the NKG-800 printer is installed, also set the printer power to DC24V for the NKG-800 while
opening the back cover as mentioned above. Regarding the NKG-800 printer power setting,
see “Connecting to the MF/HF controller” section of the NKG-800 printer.

Note3. Do not change the setting of the dip switch (S301) on the AF CONT UNIT (CMV-3775).

2-39
INSTALLATIONS

（２） Installation using the mounting bracket (MPBX44354)

Refer to the following diagram to use the mounting bracket.

Spacer

Double-sided tape

Spacer

Knob bolt

Knob bolt

2-40
 INSTALLATIONS

（３） Installation on the console (embedded)

Installation hardware is not needed when embedding the controller in the console because the screws
on the back of the MF/HF controller are used.
Refer to the following diagram to cut holes in the console panel and install the MF/HF controller.

2-41
INSTALLATIONS

（４） Installation using the flush mounting bracket (MPBC42957)

Refer to the following diagram to use the flush mounting bracket.

2-42
 INSTALLATIONS

2.2.6.3 Supplementary materials

（１） CW keyer terminal

When use a CW keyer, insert the key plug to the jack of the controller front panel (Φ3.5mm mini-plug).

key jack for Φ3.5mm mini plug)

（２） Connecting an external speaker

CAUTION
Do not short the lines of the mini plug. Doing so may cause malfunction.

Use the SP jack (Φ 3.5-mm mini-plug) on the back of the controller to connect an external speaker as
shown below.

• Use speakers that are rated for 5 W or more and have an impedance of 8 Ω or more.
• When the mini-plug is inserted the output from the internal loudspeaker is turned off.

Φ3.5-mm mini-plug

2-43
INSTALLATIONS

（３） Information

The red covered connector (Dsub-9 male) on the rear of the controller includes DC24V output pins.
Do not remove the cover except to use an external modem and so on. If the cover is always removed
and the power lines are shorted, it may cause a malfunction.

2-44
 INSTALLATIONS

2.2.7 NQW-261 Handset

2.2.7.1 External dimensions

Unit: mm
Mass: Approx. 0.4 kg (handset only)
Approx. 0.5 kg (including cradle)
Color: Black

2-45
INSTALLATIONS

2.2.7.2 Building the connector for the handset

Step 1. Stripping Step 5. * Insert the lock nut (8) into the housing term inal.
* The solder cable (6) is divided to contact positions in the housing
* Insert the O-ring (7) onto the front end of the housing.

Step 2. Insert seal ( 4) into the back half of the clam p ring (3).

Step 6. Screw the front of clamp ring (3) all the way onto the end of the
housing (1).

Step 3. Insert gask et (2) into the front half of the clam p ring (4).

Step 7. Screw sealing nut (5) onto the end of the clam p ring (3).
Tighten b y hand or with a tool.

Step 4. Insert the stripped cable into the sealing nut (2) and the clam p
ring (2).

Caution: 1. Ass'y tool (cap) can be substituted as the mating connector.

2. Ass'y hand tools (cap & wrench) must be purchased separately.

2-46
 INSTALLATIONS

2.2.8 NQD-2250 Connection Box

2.2.8.1 External dimensions

Unit: mm
Mass: Approx. 0.6 kg
Color: N4

2-47
INSTALLATIONS

2.2.8.2 Installation
Refer to the following diagram to install the connection box.

1. Remove the 4 screws (M4) holding the cover to the main unit and remove the

Cover

Main

Screw

2. Fix the main unit to the wall with 4 screws (M4) and wire the terminal
bl k

Screw
Termina
l block

Screw

3. Fix the cables to the main unit with nylon bands, and then fix the cover to the main
unit with 4 screws (M4).

Nylon band

Screw

Cable

Note) When terminating the RS-485 lines at the NQD-2250 connection TB4
1 2 3
box, set the TB4 jumper pins appropriately as shown at right. Terminate
ON

TB4
1 2 3
Terminate
OFF

2-48
 INSTALLATIONS

2.2.8.3 Connecting the signal lines

Use the following method to connect the signal lines to terminals TB1 - 2, TB 11 - 12, and TB21 - 22 on
the CQD-2250 connection board in the connection box.
Note: Connections on the terminal board of the transceiver are the same.

① Slide a thin flathead screwdriver all the way into Flathead

マイナスドライバscrewdriver
the slit as shown in the figure at the right and
then insert the signal line*.

*) Compatible wire sizes: 0.2 - 2.5 mm 2 スリット

Slit
(AWG 24~12)
Stripped length: 8 mm

Signal line port

信号線挿入口

② Remove the screwdriver and make sure that the

signal line is securely connected.

③ When the wiring is finished, secure the cables in

a bundle with the cable clamp.

Nylon band

2-49
INSTALLATIONS

2.2.8.4 Terminal description

TB1 - TB2 (CONTROLLER)

Connection
No. Name Description
point
1 GND Ground for shielded connections
2 NC
(Not used)
3 NC
4 DISP_LINE+ 600 Ω balanced, 0 dBm
5 DISP_LINE- AF receiver signal
6 DISP_KEY PTT/KEY line
NCM-2150
7 SYS_RST System reset line MF/HF
8 RS-485-A controller
Interface for RS-485 communication (57.6 kbps)
9 RS-485-B (No. 1)
10 DISP_PWR 24 VDC, maximum 3 A,
11 DISP_PWR MF/HF controller NCM-2150 dedicated power supply
12 GND
Ground
13 GND
14 GND Ground for shielded connections

TB11 - TB12 (EXTENSION 1) *Terminal board terminal

Connection
No. Name Description
point
1 GND Ground for shielded connections
2 NC
(Not used)
3 NC
4 DISP_LINE+ 600 Ω balanced, 0 dBm
5 DISP_LINE- AF receiver signal
6 DISP_KEY PTT/KEY line
7 SYS_RST System reset line CQD-2417
8 RS-485-A terminal
Interface for RS-485 communication (57.6 kbps) board
9 RS-485-B
10 DISP_PWR 24 VDC, maximum 3 A,
11 DISP_PWR MF/HF controller NCM-2150 dedicated power supply
12 GND
Ground
13 GND
14 GND Ground for shielded connections

TB21 - TB22 (EXTENSION 2) *Expansion controller terminal

Connection
No. Name Description
point
1 GND Ground for shielded connections
2 NC
(Not used)
3 NC
4 DISP_LINE+ 600 Ω balanced, 0 dBm
5 DISP_LINE- AF receiver signal
6 DISP_KEY PTT/KEY line
NCM-2150
7 SYS_RST System reset line MF/HF
8 RS-485-A controller
Interface for RS-485 communication (57.6 kbps)
9 RS-485-B (No. 2)
10 DISP_PWR 24 VDC, maximum 3 A,
11 DISP_PWR MF/HF controller NCM-2150 dedicated power supply
12 GND
Ground
13 GND
14 GND Ground for shielded connections

2-50
 INSTALLATIONS

2.2.9 NDZ-227 Data Terminal

2.2.9.1 External dimensions and installation space

Unit: mm
Weight: Approx. 2.0 kg
Color: N4

2-51
INSTALLATIONS

2.2.9.2 Data terminal installation

（１） Preparation

a. To select the MF/HF mode, set the DIP switch on the Inmarsat-C mode
back of the NDZ-227 as shown at right.
(Factory default setting: Inmarsat-C mode)

MF/HF mode

b. Put a void sticker included with the NDZ-227 as shown

at right.

Void sticker

c. Put the MF/HF sticker included with the NDZ-227 as

shown at right.

2-52
 INSTALLATIONS

（２） Installation using the mounting bracket (MPBP31721)

Refer to the following diagram to use the mounting bracket.

2-53
INSTALLATIONS

（３） Installation on the console (embedded)

Installation hardware is not needed when embedding the data terminal in the console. Remove the
covers on the four corners and install using screws. Then restore the four corners.

2-54
 INSTALLATIONS

2.2.9.3 Wiring the power cable and the signal cable

When connecting the NDZ-227 Data terminal to the controller, particularly regarding that power, use
the printer power terminal of the controller after setting to DC24V as follows.

① Remove the back cover (shaded

area in diagram) and use the AF
CONT UNIT (CMV-3775) jumper
pin (TB1) to set the terminator to
2-3 side (DISP_PWR).

TB1
② Restore the cover removed at ①
so as not to catch cables.

③ Remove the cover over the printer

power source. Then connect the

Serial connector cover DTE connection cable and the

Printer power cover DTE power cable.
After connecting the power cable,
fix it with the cable clamp and
replace the cover over the printer
power source.

Cable clamp

DC OUT

11mm

＋ －
7ZCJD0388

7ZCJD0419

2-55
INSTALLATIONS

2.2.10 NDF-369 Keyboard

2.2.10.1 External dimensions and installation space

Unit: mm
Weight: Approx. 0.4 kg
Color: Beige

Note: When installing the NDF-369 keyboard, fix it with the Velcro attached to the bottom.

2-56
 INSTALLATIONS

2.2.11 NFC-2250/2500 Antenna Tuner

CAUTION
Locate the antenna tuner, TX antenna and lead-in wire in locations as far as
possible from people and surrounding structures to satisfy the following
conditions.
• Far at least 30cm beyond anyone’s reach.
• Low vibration.
• Good ventilation and drainage.
• Protected from water (for above deck installation).
• Not exposed to smoke or corrosive gasses from the smokestack.
• Not exposed to heat.
• Protected from icing.

2.2.11.1 External dimensions and installation space

Antenna
insulator

Ventilation tube

Unit: mm
Mass: Approx. 10kg/10kg
Color: N9

2-57
 INSTALLATIONS

2.2.11.2 Antenna tuner installation

Refer to the following diagrams for the antenna tuner installation. Furthermore for this installation,
normally use the feeder kit (6ZPKD00073) and the installation materials (6ZPKD00074) mentioned on
the next pages.

Š Do not touch here

as high voltage.
Š See the following
pages for details.
600

MAX. 500
MIN. 1000

25

44
90

2-58
 INSTALLATIONS

To use the NAW-208S/208D as the MF/HF antenna to be connected to the antenna tuner, install it as
follows.

(Mounting the side whips)

2-59
INSTALLATIONS

When installing the antenna and the cables, refer to the following figures.

(Example of the NAW-208S)

2-60
 INSTALLATIONS

Tip) When installing the receiving antenna such as the NAW-60 6m whip antenna, refer to the
following figures.

When installing the Rx antenna/cable,

make more than two loops as shown at
left. However if impossible, use another
short wire to clip them all.

JQD-69C
Junction Box

Antenna wire Another

wire

Wire clip

2-61
INSTALLATIONS

List Name DWG. NO

Components list for attached parts
Feeder Kit 6ZPKD00073

ITEM NAME OF OUTLINE TYPE

Q'TY JRC CODE NO.
NO. PART (DIMENSION IN M/M) ( DESCRIPTION )

12

1 Insulator 3 NG-159A MPNG00069

148
190

2 Shackle 6 BP-O-58 MPXP0023W

3 Thimble 3 - BRXP00845

4 Wire Clip 16 PBC-3 BRBP00043

5 Shackle 3 - BRXP0016W

2-62
 INSTALLATIONS

List Name DWG. NO

Components list for accessories
Installation Materials 6ZPKD00074

ITEM NAME OF OUTLINE TYPE

Q'TY JRC CODE NO.
NO. PART (DIMENSION IN M/M) ( DESCRIPTION )

90
400
Earth
1 4 - 6ZPKD00084

130

51
Terminal
IRON COPPER

M8 3

50
2 Earth Bolt 3 - 6ZPKD00083
25 30

50
3 Earth Plate 2 - 6ZZKD01031
1200
COPPER 0.3t

φ6.4

4 Thermit 5 22-6 5JTCD00184

7.7
φ

φ13.0

5 Thermit 2 22-12 5JTAD00023

7.7
φ

φ6
Stand-off
φ30

71
59

6 2 SK-70 BRNG00153
Insulator
45 70

BP-0-59-3 2 BP-O-59-3 MTB6991W

BP-0-59-4
7 Clamp

15
2 BP-O-59-4 MTB6992W
32

Coaxial
φ19

8 5 MP-7 5JAAQ00005
Connector
40
φ19

Coaxial
9 2 M-A-JJ 5JAAA02241
Adopter
29

Antenna
10 - 3m PE-19/1.0 6ZCKD00131
Wire

11 Earth Wire - 5m 37/0.26 2265191794

2-63
INSTALLATIONS

2.2.11.3 Cable processing

（１） RF relay cable connections

Preparing tools: Cut the coating M-type coaxial connector

Coaxial cable
▸ Soldering iron (60 - 80 W)
▸ Pb-free solder
▸ Knife (for coating/ insulation)
▸ Scissors (for the shield)
Apply solder
▸ Tester

Shield

Cut the shielding

and insulation

First insert this part of

the connector Next, insert this part.

Center wire

Apply solder

Remarks: Do not melt the insulation inside.

Finished
* Finally check the
insulation resistance
between the center
wire and the shielding.

Note: When connecting the relay cable between the RF cable (7ZCJD0045) and the transceiver, use
self-fusing tape to seal the connectors and wrap vinyl tape on top of that.
Antenna tuner

After mating the connectors, seal

them with self-fusing tape, and then
wrap vinyl tape over them.

Wrap
Self fusing tape:
Wrap at least 5 times,
covering each layer half-way.

Vinyl tape:
Wrap at least 3 times,
covering each layer halfway.

2-64
 INSTALLATIONS

2.2.11.4 Wiring the control signal lines

（１） Junction box terminal

When using a junction box (NQD-2253) connect the signal lines as shown below.

Antenna tuner
Provided cable
Corresponding cable:φ8.5 ～ φ10.5

Cable gland 15b

NQD-2253 JUNCTION BOX

2
Vinyl electrical wire 7 wires/0.45 mm or more

Twist the shield and solder to vinyl wire.

Cable gland 30a

Corresponding cable:φ18.5 ～ φ20.5

TTYCYS-4

Transceiver

Antenna tuner
control cable

CQD-2415 TERMINAL UNIT

Terminal no.

PNK 24
YEL 25
WHT 26
BLK 27
RED 28
GRY 29
GRN 30
BRN 31
GND 32

Terminal block in the NQD-2253

TTYCYS-4
(To transceiver)

2-65
INSTALLATIONS

2.2.12 NQD-2253 Junction Box

2.2.12.1 External dimensions

Unit: mm
Mass: Approx. 1.2 kg

2-66
 INSTALLATIONS

2.2.12.2 Handling the attached rubber board

When installing the NQD-2253, if needed, use the attached rubber board referring below.

2-67
INSTALLATIONS

2.2.13 NKG-91 Printer

2.2.13.1 External dimensions and installation when attached to a wall

（１） External dimensions (using MPBP31446)

Installation hole

Wiring hole (back)

Wiring hole (side)

Unit: mm
Mass: Approx. 1.5 kg
Color: N4

2-68
 INSTALLATIONS

（２） Installation

Use the MPBP31446 and refer to the diagram below to install it.

M4 screw

2-69
INSTALLATIONS

2.2.13.2 External dimensions and installation for a flush mount

（１） External dimensions

Unit: mm
Mass: Approx. 0.8 kg
Color: N4

2-70
 INSTALLATIONS

（２） Installation

Refer to the diagram below during installation.

Installation hole

(Unit: mm)

Installation side cut dimensions

2-71
INSTALLATIONS

2.2.13.3 Connecting the signal lines

• Back of NKG-91 main unit

Connector terminal wiring example for power source
No. Signal name Direction Functions
DC +
1 DC + Input
power source
DC -
2 DC - Input
Serial connector power source
3 E － Ground

緑 Black
Green 黒 Red
赤

3 2 1
Power connector (6.5 V)
Printer cable:
7ZCJD0254A
(1.5 m)

Printer power cable:

DPYC-1.5
or
MVVS-20/0.18*2-6.5P-(8)

• Back of MF/HF controller (NCM-2150)

Serial connector cover

Remove the serial connector cover and the cover
Printer power cover over the printer power source. Then connect the
printer connection cable and the printer power cable.
After connecting the power cable, fix it with the cable
clamp and replace the cover over the printer power
source.
Note) When the NKG-91 is installed, set the
printer power supply to 6.5V (factory
Cable clamp default). For details of the printer power
supply setting, see the NKG-800 section.

DC 6.5 V
max. 2 A
(for printer)

2-72
 INSTALLATIONS

2.2.14 DPU-414 Printer (desktop type)

2.2.14.1 External dimensions and installation space

Velcro
(Provided)

Unit: mm
Mass: Approx. 0.6 kg
Color: Ivory

Note) When installing the DPU-414 printer, fix it with the Velcro attached to the bottom.

2-73
INSTALLATIONS

2.2.14.2 Connecting to the MF/HF controller

To connect the DPU-414 to the MF/HF controller* via the serial cable (7ZCJD0254A), set the DIP SW1-1 to OFF.
* If connecting to the NDZ-227 Data terminal, set the internal DIP SW1-1 to ON and SW2-1 to OFF, and then
connect the printer cable (7ZCSC0205A) to the PARALLEL connector on the back of the DPU-414.

• Back of DPU-414

Printer cable Printer power cable

GND
DC 6.5 V, 2 A
+ -
Printer cable:
7ZCJD0254A
(1.5 m)

Printer power cable:

7ZCJD0257C (1.5 m)

• Back of MF/HF controller (NCM-2150)

Remove the serial connector cover and the cover
Serial connector cover over the printer power source. Then connect the
Printer power cover printer connection cable and the printer power cable.
After connecting the power cable, fix it with the cable
clamp and replace the cover over the printer power
source.
Note) When the DPU-414 is installed, set the
printer power supply to 6.5V (factory
default). For details of the printer power
Cable clamp supply setting, see the NKG-800 section.

DC 6.5 V
max. 2 A
(for printer)

2-74
 INSTALLATIONS

2.2.15 NKG-800 Printer (Centronics compliant/desktop type)

2.2.15.1 External dimensions and installation space

Over
以上
150
150

430
430以上
Over
280
380 19

500
500以上
40
45

Over
193

108

65 31
150
Over
280
50 380 150
以上
376
Over
150
150
以上

Unit: mm
Mass: Approx. 3.7 kg

Note) When installing the NKG-800 printer, fix it with the Velcro attached to the bottom.

2-75
INSTALLATIONS

2.2.15.2 Connecting to the MF/HF controller

To connect to the MF/HF controller*, set the printer power and connect cables as follows.
* To connect to the NDZ-227 Data terminal, use the printer cable (7ZCSC0205A).

• Back of MF/HF controller (NCM-2150)

When connecting the NKG-800 printer to the controller, set the printer power of the controller to
DC24V as follows.
NOTICE) When using a 6.5V printer, always set (or confirm) the TB1 terminator to 1-2 side.

① Remove the back cover (shaded

area in diagram) and use the AF
CONT UNIT (CMV-3775) jumper pin
(TB1) to set the terminator to 2-3

TB1
side (DISP_PWR)
② Restore the cover removed at ①
so as not to catch cables.
③ Remove the cover over the printer
Printer power cover
プリンタ電源カバー power source. Then connect the
printer connection cable and the
printer power cable.

Parallel printer signal

パラレルプリンタ信号 After connecting the power cable,
(Centronics I/F)
（セントロニクスI/F） fix it with the cable clamp and
replace the cover over the printer
power source.
Cable clamp
ケーブルクランプ

DC OUT

DC6.5V
DC24V
(Common
最大2A to the
system power)
（プリンタ専用）

11mm

＋ －

6ZCSC00407 6JNKD00100B

• Back of the NKG-800

Power cable

Printer connection cable

2-76
 INSTALLATIONS

2.2.15.3 Setting the DIP switch

When connecting the printer (NKG-800) to the JSS-2xxx series, set the DIP switches as follows.

① Open the printer cover, remove the ink ribbon cartridge, and use your hand to move the print
head to the far right.

Print head

② Grab the protrusion on the compartment cover and remove by sliding it to the left.

Compartment cover

③ Turn all the DIP switches off.

Note: Set the NKG-800 DIP switches as follows according to the device it is connected to.

Connected device DIP switch setting

NCM-2150/ NDZ-227 (JSS-2xxx)
NCT-196(N)/ NDZ-127J (JSS-x96)
NCT-620D (JSS-825D)

NCH-851/852 (JSS-850)
NCH-1961/1962 (JSS-x96)
NDZ-127C (JUE-75C)

NDZ-127N (JSS-825NA/NC)

④ Replace the parts described above and the cover.

2-77
INSTALLATIONS

2-78
 DA_TEMP
DA
TEMP. LPF_OUT
TD62083 SWR
2SC5337 2SC5337X2 RD15HVF MRF171A PA(A) ARF475×2 TX_ANT
SENSOR
RF_IN

3.1.1
STEP AM-PM SWR
ATT ADJ. SENSOR

PA_VR_A ATT
PA_BIAS_A1～4
３ｄB 50ohm
DET PA （A) PA_VF_A
NJM2732 TD62083 TD62083
TEMP.
NJM2904
PA_TEMP_A

TX_OUT
DA_VF

BR24L02
DC24V ATT1～9 AM_PM１ ９V

TUNE
DA_ON
AM_PM2 Ic EEP

ANT_TX
ALM PA_PWR_A

PWR IN
RF_OUT_VR
PA_PWR_A SEN ROM

RF_OUT_VF
SOR
FAN1
RBK FAN1
OC_A Vc FAN1_ALM
PS_RBK
SEN
ALM SOR

9V
PA_PWR_OUT_A PA_PWR_OUT

PA_WP

3R3V
PA_SCL
PA_SDA
OC_A
ALM
PA_PWR_ON_A C.k.t FAN3
PA_PWR_ON_A
BAND TX Freq.
FAN3
LPF1 1.6～ 2.3MHz FAN3_ALM

PWR CONT
DC_OPE AC_OPE
LPF2 2.3～ 3.3MHz
LPF3 3.3～ 4.8MHz
PS ALM PS_ALM

OC_A
LPF4 4.8～ 6.9MHz

PA_IC_A
POLY LPF5 6.9～10.0MHz

PA_VC_Ａ

ALM_RST
CTRL PWR SWITCH
10V
LPF6 10.0～14.5MHz

IC_HI_RANG
3.1 Block diagram

LPF7 14.5～20.9MHz
24V LPF8 20.9～30.0MHz
POLY
SWITCH +BK 3R3V TC74VHC238
LPF_C
POLY 10V REG
LPF_B
NTD-2250 TRANSCEIVER

SWITCH 9V 24V DECODER

SW LPF_A
REG 3R3V
REG
RX_IN

WKR_RX_OUT
DISP_PWR2 PA_BIAS_A1～4
RX_OUT

DISP_PWR1
WKR_RX_IN

RX_ANT
TLP181GR
RBK

DA_ON
PT ２５LC256 ２５LC256 RX_OUT 50ohm

ATT1～9
AM_PM1
AM_PM2
PA_WP
ATU_TXD ATU_TXD RBK_ERR OC_A

PA_SCL
PA_SDA
NJM2732 RN1305
EEP EEP

IC_HI_RANG
PA_KEY LOAD_ALM LOAD DMC_OAL
ANT_CURR ANT_CURR ROM ROM NJM2732 DMC_OAL
TLP181GR ALM C.k.t
ATU_24V LOAD
PT TLP181GR
ATU_RXD ATU_RXD
TLP181GR SO/SCK/SI LOAD_A DMC_OAS PT

ATU
LOAD_ALM_RST DMC_OAS

FAN1
FAN3
PT ALM_RST

IRQ0
IRQ1
PA_MUTE PA_MUTE
ROM1_CS LOAD_ALM_RST TLP181GR
2SD2141 FAN_ON DMC_SEL PT
RBK DMC_SEL
SCLK
RBK PROTEC RBK FAN1_ALM，FAN3_ALM
-TOR DAC DATA TLP181GR
RBK_ERR 4ch SYNC_A DMC_DRQ PT
DMC_DRQ
-BK BK_ERR
DAC104S085×2 TUNE Deley
PROTEC 10V POLY
+BK +BK -TOR PA_PWR_OUT DMC_PWR
ANT_TX SWITCH
PA_PWR_ON_A
2SD2141 RN1305
CPU RX_OUT
DMC_RDY
-BK AC_OPE DMC_RDY
GPS_RX-B PS_ALM H8S2328
GPS_RX-A TEST_MONI
RN1305 ANT_CURR RN1305
RCONT- DA_ＴＥＭＰ DMC_DRA
RCONT DMC_DRA
RCONT+ PA_ON DA_VF
3. APPENDIX

ISL3172 RN1305
SEL_BK PA_TEMP_Ａ

ACCESSORY
TXD_485 ADC ports DMC_DAL
EXT_KEY DMC_DAL

ALM
TXD_232 PA_VF_A
LINE_IN-
RS-485-A RXD_485 TLP181GR
LINE_IN+ RS-485
TRAN- RXD_232 DMC_DAS PT
LINE_OUT- PA_VC_Ａ NJM2732 DMC_DAS
RS-485-B SCEIVER DE_485
LINE_OUT+
RE_485 PA_VF_A
４８５TX PA_IC_A SP3071

OC_A
DISP_PWR1 DISP_PWR1 RS-422 RMS_TX-A

LOAD_A
PA_SEL1 RMS_TXD
ICL3232 DRIVER

RBK_ERR
DISP_PWR2 DISP_PWR2 LOAD_A LOAD_A RMS_TX-B

TX

LOAD_ALM
MTN ALM C.k.t
PA_VR_A
RS-485-B PA_SEL2（NC) LOAD_A SP3071
TLP181GR
RS-485-A RCONT RS-422 AME_TX-A
PT RS-２３２C AME_TXD
SYS_RST SYS_RST TRAN- DRIVER AME_TX-B
LOAD_ALM_RST
DISP_KEY SCEIVER TRX_TXD 18.4332MHz TLP181GR

OPT_LPF

CONTROLLER
DISP_LINE- RXD_232C PT AME_RX-A
ATU_TXD
ATU_RXD
AME_RXD

PA_TYPE1,2

PA_MUTE
DISP_LINE+ MTN_RXD AME_RX-B
RESET

CNT_TYPE1～3
PC400J

MODEM_RST

TUNE_KEY
PA_ERR IC SYS_RST PT 422_RX-A

SEL_BK_OUT
D-SUB 422_RXD
PA_RDY TRX_RST 422_RX-B

10V
10V
9pin NJU7704

INF3R3V

RF_IN
LINE_IN+
LINE_IN-
EXT_KEY
SEL_BK
-BK_IN
BK_OUT
TRX_RST
TRX_MAIN
PA_KEY
TUNE_KEY
PA_RDY
SEL_BK_OUT
BK_ERR
TRX_TXD
MNT_RXD
MODEM_RST
GPS_RX-A
GPS_RX-B

MODEM_PWR
TRX_PWR
DISP_LINE+
DISP_LINE-
DISP_KEY
RS-485-A
RS-485-B
LINE_OUT+
LINE_OUT-
TX_OUT
RX_IN WKR_RX_OUT WKR_RX_ANT

RX_OUT WKR_RX_IN

WKR/RX_ANT

3-1
APPENDIX
 DA_TEMP
DA
TEMP. LPF_OUT

3-2
PA(A) ARF475×2
TD62083 SWR
2SC5337 2SC5337X2 RD15HVF MRF171AX2 TX_ANT
SWR SENSOR
RF_IN SENSOR 3.1.2
STEP AM-PM
ATT ADJ. TD62083
PA_VR_A
PA_BIAS_A1～4
ATT
PA （A) PA_VF_A

SPLITTER
TEMP.
３ｄB 50ohm
DET COMB.
NJM2904 NJM2732 TD62083 TD62083
APPENDIX

PA_TEMP_A
TD62083

TX_OUT
DA_VF

DET
NJM2406
DC24V ATT1～9 AM_PM１ ９V COMB_UNBL

TUNE
DA_ON
AM_PM2 Ic COMP

ANT_TX
ALM PA_PWR_A

RF_OUT_VR
PA_PWR_A SEN

RF_OUT_VF
SOR ONLY_A
Ic

PWR IN
PA_PWR_B PA_PWR_B FAN1
SEN
SOR ONLY_B
FAN1
OC_B OC_A Vc FAN1_ALM
PA(B) ARF475×2
PS RBK RBK SEN
COMB_A SOR SWR FAN2
PA_PWR_OUT_A
SENSOR
FAN2
OC_B OC_A Vc FAN2_ALM
PA_PWR_OUT_B COMB_B PA_VR_B
ALM ALM SEN PA_BIAS_B1～4
PA_PWR_ON_A PA_PWR_ON_A C.k.t C.k.t SOR FAN3
PA （B) PA_VF_B
TEMP.
BAND TX Freq.
PA_PWR_ON_B PA_PWR_ON_B FAN3
NJM2904 LPF1 1.6～ 2.3MHz FAN3_ALM

PWR CONT
DC_OPE AC_OPE PA_TEMP_B LPF2 2.3～ 3.3MHz
LPF3 3.3～ 4.8MHz

ALM
PS ALM PS_ALM

PA_PWR_OUT
OC_B
OC_A
BR24L02 LPF4 4.8～ 6.9MHz

PA_IC_B
PA_IC_A
POLY LPF5 6.9～10.0MHz

PA_VC_B
PA_VC_Ａ

ALM_RST
ALM_RST
CTRL PWR SWITCH
10V EEP
ROM
LPF6 10.0～14.5MHz

IC_HI_RANG
IC_HI_RANG
LPF7 14.5～20.9MHz
24V COMB_A ONLY_A LPF8 20.9～30.0MHz
POLY
SWITCH +BK 3R3V TC74VHC238
COMB_B LPF_C
NTD-2500 TRANSCEIVER

POLY 10V REG ONLY_B

SWITCH
LPF_B
9V 24V DECODER

9V
SW LPF_A

PA_WP
REG 3R3V

3R3V
PA_SCL
PA_SDA
REG
PA_BIAS_A1～4 RX_IN

COMB_UNBL
WKR_RX_OUT

DISP_PWR2 PA_BIAS_B1～4
RX_OUT

DISP_PWR1
WKR_RX_IN

PA BAL COMB_UNBL ALM_RST RX_ANT

TLP181GR
RBK LATCH

DA_ON
PT ２５LC256 ２５LC256 RX_OUT 50ohm

ATT1～9
AM_PM1
AM_PM2
PA_WP
ATU_TXD ATU_TXD RBK_ERR OC_A

PA_SCL
PA_SDA
NJM2732 RN1305
EEP EEP OC_B

IC_HI_RANG
PA_KEY LOAD_ALM LOAD DMC_OAL
ANT_CURR ANT_CURR ROM ROM NJM2732 DMC_OAL
TLP181GR ALM C.k.t
ATU_24V LOAD_B LOAD
PT TLP181GR
ATU_RXD ATU_RXD
TLP181GR SO/SCK/SI LOAD_A DMC_OAS PT

ATU
LOAD_ALM_RST DMC_OAS
FAN1
FAN2
FAN3

PT ALM_RST

IRQ0
IRQ1
PA_MUTE PA_MUTE
ROM1_CS LOAD_ALM_RST TLP181GR
2SD2141 FAN_ON DMC_SEL PT
RBK DMC_SEL
SCLK
RBK PROTEC RBK FAN1_ALM～FAN3_ALM
-TOR DAC DATA TLP181GR
RBK_ERR Deley
4ch SYNC_B COMB_B DMC_DRQ PT
DMC_DRQ
-BK BK_ERR SYNC_A
TUNE Deley
PROTEC DAC 10V POLY
+BK +BK -TOR PA_PWR_OUT DMC_PWR
4ch ANT_TX SWITCH
PA_PWR_ON_A
2SD2141 RN1305
PA_PWR_ON_B RX_OUT
DAC104S085×2 CPU DMC_RDY
-BK AC_OPE DMC_RDY
GPS_RX-B PS_ALM H8S2328
GPS_RX-A COMB_A TEST_MONI
RN1305 ANT_CURR RN1305
COMB_B
RCONT- DA_ＴＥＭＰ DMC_DRA
RCONT DMC_DRA
RCONT+ PA_ON DA_VF
PA_TEMP_Ａ RN1305
SEL_BK ISL3172

ACCESSORY
TXD_485 ADC ports PA_TEMP_B DMC_DAL
EXT_KEY PA_VF_A DMC_DAL

ALM
TXD_232
LINE_IN- PA_VF_B
RS-485-A RXD_485 TLP181GR
LINE_IN+ RS-485
TRAN- RXD_232 PA_VC_Ａ DMC_DAS PT
LINE_OUT- NJM2732 DMC_DAS
RS-485-B SCEIVER DE_485 PA_VC_B
LINE_OUT+
RE_485 PA_IC_A PA_VF_A
４８５TX SP3071

OC_A
OC_B
PA_IC_B
DISP_PWR1 DISP_PWR1 RS-422 RMS_TX-A

LOAD_A
LOAD_B
PA_SEL1 RMS_TXD
ICL3232 LOAD_A DRIVER

RBK_ERR
DISP_PWR2 DISP_PWR2 LOAD_A RMS_TX-B

TX

LOAD_ALM
MTN ALM C.k.t
PA_VR_A
RS-485-B PA_SEL2（NC) SP3071

COMB_UNBL
TLP181GR LOAD_A
RS-485-A RCONT RS-422 AME_TX-A
PT RS-２３２C AME_TXD
SYS_RST SYS_RST TRAN- DRIVER AME_TX-B
LOAD_ALM_RST PA_VF_B
DISP_KEY SCEIVER TRX_TXD 18.4332MHz TLP181GR

OPT_LPF

CONTROLLER
DISP_LINE- RXD_232C PT AME_RX-A
ATU_TXD
ATU_RXD

AME_RXD

PA_TYPE1,2

PA_MUTE
DISP_LINE+ MTN_RXD LOAD_B LOAD_B AME_RX-B
ALM C.k.t
PA_VR_B
RESET

CNT_TYPE1～3
LOAD_B PC400J
MODEM_RST

TUNE_KEY
PA_ERR IC SYS_RST PT 422_RX-A

SEL_BK_OUT
D-SUB 422_RXD
PA_RDY TRX_RST NJM2732 422_RX-B

10V
10V
9pin NJU7704 LOAD_ALM_RST

INF3R3V

RF_IN
LINE_IN+
LINE_IN-
EXT_KEY
SEL_BK
-BK_IN
BK_OUT
TRX_RST
TRX_MAIN
PA_KEY
TUNE_KEY
PA_RDY
SEL_BK_OUT
BK_ERR
TRX_TXD
MNT_RXD
MODEM_RST
GPS_RX-A
GPS_RX-B

MODEM_PWR
TRX_PWR
DISP_LINE+
DISP_LINE-
DISP_KEY
RS-485-A
RS-485-B
LINE_OUT+
LINE_OUT-
TX_OUT
RX_IN WKR_RX_OUT WKR_RX_ANT

RX_OUT WKR_RX_IN

WKR/RX_ANT
 TL3414AI
RX BPF8
PCM1742 NJM2746
RX ANT ATT 6 ATT 12 ADSP-21363 LINE OUT+
RX IN
3.1.3

RX BPF7
DAI D/A LINE OUT-

AGC
(90kHz SN74CBT3125 NJM2737 NJM2737
～29,999.9kHz)
2SC4116 2SC4116 2SC4116
RX BPF6 0° TL3414AI
MMBFJ310 MMBFJ310 1st IF FILTER +45° AK5385BVF
DAI D/A DEM OUT+
fc=35MHz fc=35MHz X4 X4 70.036MHz fs=156.25kHz
RX BPF5
DEM OUT-
fs=156.25kHz
A/D DAI
RX BPF4
M25P40
BF998R
FROM DEMOUT SEL

DIODE SWITCH
DIODE SWITCH
ATT ATT 0°
6dB 12dB
SPI (SPI) DUP DEMOUT
RX BPF3
-45°

TRX MAIN
4Mbit
MODEM MONI
DSP 20MHZ DSP BR25L640
BAND RX Freq. RX BPF2 EEPROM TL3414AI
TC7WH04
RX BPF1 1,600～29,999.9kHz 2SC5337 (SPI)
RX BPF2 90～399.9kHz 64kbit
RX BPF3 400～1,599.9kHz RX BPF1
IO UPDATA DAI
RX BPF4 1,600～3,199.9kHz
2ND LO DDS DAI NJM2746
RX BPF5 3,200～6,099.9kHz 0°
(70MHz) PLL DAI MAX4622
RX BPF6 6,100～10,499.9kHz 90°
DUC RST DAI DISP LINE+
RX BPF7 10,500～17,999.9kHz
RXTUNE1,2,4,8,16 DAI A/D
RX BPF8 18,000～29,999.9kHz TC74VHC238 A/D,D/A DISP LINE-
RX BAND1
DECODER RX BAND2 1ST LO
AK5385BVF
RX BAND4 (70.126～100.0359MHz) 2SC3357 TC74VHC4040 fs=156.25kHz
1/64 DAI LINE DISP LINE DISP ON
DPS RST
DAI

DAI
CMN-2250 TRX UNIT

MB15E03 2SC3356 X2 2SC3356 AD9951 2SC3357 LINE MODEM

NJM2746
LINE EXT

400MHz
NJU7704F-29A
PLL 20MHZ PLL DDS 1/2 RESET

RD
LINE IN+

WR
ALE
IC
2SC3356 2SC3356 IO UPDATE TC7WH74 2SC3356 OPE LINE IN-
PLL LOCK OSK RX ON
ATT

AD15～AD0
LO 20MHZ 1/2 AD 20MHZ MOD IN+
PLL RST

DAC RST
DDS RST
MOD IN-

WD OUT
RST
D3R3V
DUC 400MHZ FPGA:XC3S200PQG208I
DET TX DET
1
DAC RST 2SC4116
NJM2406F W.D.T
DAC5674 RS485 CONNECT
2SC5337 fc=35MHz
RS485DRV
1 DUC BLOCK ADDRESS
ATT D/A DECORDER RAM UART TX TXD485
TX OUT 14bit 0 128byte×1
0 57.6kbps RS-485
TRAN-
RS-485-A
(1.6MHz TEST DUC 100MHZ RAM sentenc UART RX SCEIVER
～29.9999MHz) 128byte×2 check RS-485-B
2SC4116 57.6kbps
ISL3172EIBZ
DUP TXD

DUC OUTEN
RAM UART TX TXD
TX ON 128byte×1
TRX TXD
DUC RST 38.4kbps CONT
TX ON MODEM TXD
RAM sentenc UART RX
128byte×2 check
MNT RXD
38.4kbps
AN7709SP NJM2885 NJM2880U1-33
DATA BUS

～16
REG REG REG A3R3V LINE MODEM
ADDRESS BUS

ATT 6
TLP181GR

TX ON
RX ON

ATT 12

RX ANT
DISP KEY IN
DEMOUT SEL
PT
LINE DISP ON
MODEM MONI

LINE EXT
A5V

ANALOG ON

PLL LOCK
LINE DISP

TX BAND3
TX BAND2
TX BAND1
DISP KEY
RS485 CONNECT

RX BAND1
RX BAND2
RX BAND4
AN7709SP C9V
2SC3324

RXTUNE1 5bit
REG A9V DISP KEY OUT

PLL 20MHZ
LO 20MHZ
AD 20MHZ
DSP 20MHZ
DUC ON
TC7W14 TC7WU04 PIO TLP181GR
TEST
ANALOG ON EXT KEY IN PT
PWR KEY CONT EXT KEY
NJM2374
TLP181GR

PA UNIT
SW SEL BK IN PT
REG
D3.3V SEL BK
FPGA 20MHZ

TXFIL

RXFIL
2bit
3bit
TLP181GR
ERR485

TX DET
BK IN

EXT CLK
DUP BK IN

NJM2861F25 PT
SCAN STOP IN

TCXO:20MHz

TRX MAIN
-BK IN

TXFIL DET
DUP BK OUT

NJM2860

INT DTCXO
D2.5V
REG TLP181GR
C9V REG
PT
BK OUT F BK OUT
NJM2885DL1-18
INT
INT DTCXO DTCXO R3112Q101A
REG D1.8V
NJM2406
SSB
FPGA RESET KEY IN
R1225N122K EXT CLK Comp NJM2887 Configration IC
BK ERR
BK OUT F

DIPSW1,2

ROM
HARD VER

SW NJM2741 C9V
SCAN STOP

D1.2V REG
REG
DISP KEY OUT

Comp XCF01SVOG20C
ERR485
PA KEY
TX RDY

DUP BK
PA RDY

DUPLEX
RX BUSY

TRX RST
TXFIL KEY
TUNE KEY

D1R2V
TXFIL TEST

SEL BK OUT
MODEM SEL
MODEM KEY

TXFIL BAND8
TXFIL BAND4
TXFIL BAND2
TXFIL BAND1

3-3
APPENDIX

DTCXO(OPTION) WKR MODEM UNIT

APPENDIX

3.1.4 CMJ-2250 WKR MODEM UNIT

DMC

DIODE SWITCH

DIODE SWITCH

TRX

3-4
 APPENDIX

3.1.5 NBD-2250 POWER SUPPLY

UCC28070DW

3-5
 3-6
PFC_ON_DC
（ｆrom DC_DC_UNIT）
PFC_DC
（ｆrom DC_DC_UNIT）
150V
（ｆrom DC_DC_UNIT）
UCC28070DW
+12VCONT
（ｆrom DC_DC_UNIT）
CLK_SYNC
（ｆrom DC_DC_UNIT）
24V+
PS_ALM
PS_RBK
PA_PWR_OUT
PA_PWR_ON
CTRL_PWR
NBD-2500 POWER SUPPLY 3.1.6
APPENDIX
 EXT SP AF CONT UNIT
CMV-3775
3.1.7

IC control D/A
P_BACK SP +/-
LINE_OUT LCD UNIT
A/D
SYS_RST CDE-3770
S5 Volume
S6 +3.3V VDD
ADD SP
ADD
SP OUT +26V
S7
S4 S2 Contrast VEE
FLM
0Ω
SIDETONE CL1
S9

150Ω

150Ω
CL2
LCD Control D0
S1 0Ω D1

SIDETONE
Phone D2
D3

Transceiver I/F
0Ω DISPLAYOFF
PT
DISP_KEY_OUT LINE_IN MIC
S3 LED+
PT S10 LCD Brightness
DISP_KEY_IN S11 LED-

DISP_PWR

MAIN PANEL UNIT

RS485
+3.3V CCK-3775
drv.
+5V
RS485DRV

(MF/HF)
RTN7-0

(MF/HF)
MEAS_ON

(MF/HF)
Key Scanning

TONE
RS485SEP

LINE_TX
TERM_ON
LINE_DUP
LINE_EXT
P_BACK
IC control
AF_MUTE
Vol control
TONE_SEL
TLEV_A/B/C
BP_CLICK
SHTDWN

MIC_GAIN
PVOL_A/B/C

TONE_L
(MF/HF)
SCAN2-0
Key Brightness KEY_BRT
(MF/HF) OFF_HOOK ENC_A/ENC_B ENC_A/ENC_B
SW ALM_LED ALM_LED
SEL422 PT
DET232 RBK_ON
DET422 RS485 I/F
SCIF1 BK_ERR
RXD/HOOKSW
OFF_HOOK
OCC SUB PANEL UNIT
232C Key Control
NCM-2150 MF/HF CONTROLLER

drv.
CCK-3776
RS232 I/F SEL422 +5V
SCIF0 RTN1-0
DET422 Key Scanning
IC control SIOF0 (SCI) DET232 SCAN0
PIO
F-R_SEL (MF/HF) CPU F-R_SEL Key Brightness KEY_BRT
SEL422 SIOF1 (SCI)
422 Vol control RS485DRV (DC)
VOL_IN VOL

Maintenance
Serial Printer/
drv. SH7720 RS485SEP
EPROM (DC)
64kbit IIC HD6417720BP133BV ENC_A, ENC_B SQL_GAIN SQL
PT Key Scanning
LCD Control PS_CONT PWR_CONT

FROM Data Bus ALM_LED PWR_DET PWR key

8Mbit PWR_DET
Printer Address Bus
PRT__PWR PRT_PWR PWR_OFF PWR_OFF
PS TXD/BIAS
TXD/BIAS CPU_KEY DISP_LINE+
BIAS SW PWR_CONT
SP+ SDRAM IRQ0 DISP_KEY_IN
SP +/- 64Mbit A/D Conv. D/A Conv.
SP- TPU0 TONE
CLK RESETP RESETM AN0 1 2 DA0 1 TPU1 LCD Brightness SP OUT Internal speaker
EXT_PWR
BK RBK_ON
Contrast
Control BK_ERR Printer Control PLD
EXT_KEY CLK Key Brightness Phone
Reset
(MF/HF) 11.0592M VOL_IN
LINE_IN SQL_GAIN MIC

Modem
External
6 sec Reset Temp
+1.5v
PWR_CONT delay RXD/HOOKSW
LINE_OUT (MF/HF)
AVR Temp.
CONTROL UNIT
Handset

RST_RTN
CDJ-3775 TXD/BIAS
(MF/HF) CPU_KEY OCC
EXT_PWR +3.3v +5v
Fuse DISP_KEY_OUT
PRT_PWR (MF/HF) PTT_IN
Fuse PT
DISP_PWR 6.5V PTT_SEL
AVR +9V_AF CW_KEY_SEL
PT
SYS_RST CW_KEY_IN
12V +12V
(VHF:9V) +12V_SP CW KEY
Printer Control EXT_KEY_SEL

Printer
AVR +5V_AF EXT_KEY_IN
Key Control
5V +5V
AVR +3.3V EXT_KEY

+26V +26V

GND

3-7
APPENDIX
APPENDIX

3.1.8 NDZ-227 DATA TERMINAL

3-8
 3.1.9

200Ω
50Ω:200Ω DUMMY ANT
CS RF_OUT
RF_IN ANT RF_OUT LOAD
SWR
RF_IN CURRENT ＡＮＴ
SENSOR
SENSOR ×2S

+24V
max.3.5kV±0.5kV
CP
7.5kV Latch
×2S ×2S ×2S ×2S ×2S ×2S
2a 2a×2S Relay
0.5kV
HI_VOLTAGE 2a×2S 6kV
NJM2904 SENSOR
L0 L1 L2 L3 L4 L5 L6 L7 L8 L9A L9B
2a×2S +24V
IA CS
SWR_VR SWR_VF 0.3kV
2a HI_VOLT

CP DUMMY_TEST
LOAD
2a 2a ×2S ×2S ×2S ×2S 2a
SENSOR ANT_ON

Set
Relay
Cont Reset
PHASE LOW_R +24V
SENSOR CI0 CI1 CI2 CI3 CI4 CI5 CI6 CI7 CI8 CI9 CO0 CO1 CO2 CO3 CO4 CO5 CO6
POLY
+24V SWITCH
+24V
NFC-2250 ANTENNA TUNER

L_PHASE TUNE
+24V

CO2～CO1,CP,
FAN
FAN L2～L0, CI4～CI1， DUMMY_TEST,CS
SWR_VF

SWR_VR

HI_VOLTAGE
L_PHASE
FAN_ALM +5V CO_ON

FAN
FAN_ALM
TUNER_TYPE
TUNE
LOW_R
IA
L3～L9A,L9B
CI9～CI5 CO6～CO3 ANT_ON

NJM2732 POLY
COMP. SWITCH
TEMP
NJM7805 TD62083 TD62083 TD62083 TD62083 DTC114

DRIVER DRIVER DRIVER DRIVER ＲＢＫ_IN

REG +5V
TC7S02 2SA1313

ANT_ON
+24V TC7S02
TLP181 DUMMY_TEST
PT ＲＢＫ_IN
ＲＢＫ IRQ3 RBK_IN
DTC114

VF_DET
PA_MUTE
BK_ERR
ALM
RXD2 IRQ2
HI_VOLTAGE
RBK TXD2 COMP.
ALM RES RES RESET
NJM2732 IC
ADRESS BUS NJM2903
TLP181 ２SA1162
DA1 ANT_CURR
PT BK_ERR TC7W53
PA_MUTE CPU
HV_SET
DATA BUS HD6413007F20 AN7/DA0
TLP181
PT
ATU_RXD FLASH
WR
ROM
NJM2732
MBM29F400
RD S-8110C
ATU_24V BC AN3 TEMP.

CE NJM2732
TEMP
ANT_CURR ANT_CURR AN2
RY/BY
TLP181 ２SA1162

RES
AN1
PT

RES0
ATU_TXD AN0
NJM2903

RES RST_OUT VF_DET COMP.

RESET
２SA1162
IC

NJU7704F3-45A 19.6608MHz

3-9
APPENDIX
 3-10
RES
RES0
+24V
FAN
FAN_ALM
DTC114
HI_VOLTAGE
TUNER_TYPE
IA
TUNE
HI_VOLTAGE
LOW_R
L_PHASE
IA
SWR_VR
SWR_VF
3.1.10 NFC-2500 ANTENNA TUNER
APPENDIX
 JSS-2250/2500
2250N/2500N
MF/HF RADIO EQUIPMENT

INSTALLATION
MANUAL

For further information,contact:

Not use the asbestos

URL http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
Facsimile : +81-3-3779-1420
e-mail : [email protected]
AMSTERDAM Branch
Telephone : +31-20-658-0750
Facsimile : +31-20-658-0755
e-mail : [email protected]
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile : +1-206-654-7030
e-mail : [email protected]
CODE No.7ZPJD0537 01ETM ISO 9001, ISO 14001 Certified
SEP. 2012 Edition 1 JRC Printed in Japan